diff options
Diffstat (limited to 'arch/arm/common/locomo.c')
| -rw-r--r-- | arch/arm/common/locomo.c | 884 |
1 files changed, 884 insertions, 0 deletions
diff --git a/arch/arm/common/locomo.c b/arch/arm/common/locomo.c new file mode 100644 index 000000000..da30a4d4f --- /dev/null +++ b/arch/arm/common/locomo.c @@ -0,0 +1,884 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * linux/arch/arm/common/locomo.c + * + * Sharp LoCoMo support + * + * This file contains all generic LoCoMo support. + * + * All initialization functions provided here are intended to be called + * from machine specific code with proper arguments when required. + * + * Based on sa1111.c + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/delay.h> +#include <linux/errno.h> +#include <linux/ioport.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/spinlock.h> +#include <linux/io.h> + +#include <asm/irq.h> +#include <asm/mach/irq.h> + +#include <asm/hardware/locomo.h> + +/* LoCoMo Interrupts */ +#define IRQ_LOCOMO_KEY (0) +#define IRQ_LOCOMO_GPIO (1) +#define IRQ_LOCOMO_LT (2) +#define IRQ_LOCOMO_SPI (3) + +/* M62332 output channel selection */ +#define M62332_EVR_CH 1 /* M62332 volume channel number */ + /* 0 : CH.1 , 1 : CH. 2 */ +/* DAC send data */ +#define M62332_SLAVE_ADDR 0x4e /* Slave address */ +#define M62332_W_BIT 0x00 /* W bit (0 only) */ +#define M62332_SUB_ADDR 0x00 /* Sub address */ +#define M62332_A_BIT 0x00 /* A bit (0 only) */ + +/* DAC setup and hold times (expressed in us) */ +#define DAC_BUS_FREE_TIME 5 /* 4.7 us */ +#define DAC_START_SETUP_TIME 5 /* 4.7 us */ +#define DAC_STOP_SETUP_TIME 4 /* 4.0 us */ +#define DAC_START_HOLD_TIME 5 /* 4.7 us */ +#define DAC_SCL_LOW_HOLD_TIME 5 /* 4.7 us */ +#define DAC_SCL_HIGH_HOLD_TIME 4 /* 4.0 us */ +#define DAC_DATA_SETUP_TIME 1 /* 250 ns */ +#define DAC_DATA_HOLD_TIME 1 /* 300 ns */ +#define DAC_LOW_SETUP_TIME 1 /* 300 ns */ +#define DAC_HIGH_SETUP_TIME 1 /* 1000 ns */ + +/* the following is the overall data for the locomo chip */ +struct locomo { + struct device *dev; + unsigned long phys; + unsigned int irq; + int irq_base; + spinlock_t lock; + void __iomem *base; +#ifdef CONFIG_PM + void *saved_state; +#endif +}; + +struct locomo_dev_info { + unsigned long offset; + unsigned long length; + unsigned int devid; + unsigned int irq[1]; + const char * name; +}; + +/* All the locomo devices. If offset is non-zero, the mapbase for the + * locomo_dev will be set to the chip base plus offset. If offset is + * zero, then the mapbase for the locomo_dev will be set to zero. An + * offset of zero means the device only uses GPIOs or other helper + * functions inside this file */ +static struct locomo_dev_info locomo_devices[] = { + { + .devid = LOCOMO_DEVID_KEYBOARD, + .irq = { IRQ_LOCOMO_KEY }, + .name = "locomo-keyboard", + .offset = LOCOMO_KEYBOARD, + .length = 16, + }, + { + .devid = LOCOMO_DEVID_FRONTLIGHT, + .irq = {}, + .name = "locomo-frontlight", + .offset = LOCOMO_FRONTLIGHT, + .length = 8, + + }, + { + .devid = LOCOMO_DEVID_BACKLIGHT, + .irq = {}, + .name = "locomo-backlight", + .offset = LOCOMO_BACKLIGHT, + .length = 8, + }, + { + .devid = LOCOMO_DEVID_AUDIO, + .irq = {}, + .name = "locomo-audio", + .offset = LOCOMO_AUDIO, + .length = 4, + }, + { + .devid = LOCOMO_DEVID_LED, + .irq = {}, + .name = "locomo-led", + .offset = LOCOMO_LED, + .length = 8, + }, + { + .devid = LOCOMO_DEVID_UART, + .irq = {}, + .name = "locomo-uart", + .offset = 0, + .length = 0, + }, + { + .devid = LOCOMO_DEVID_SPI, + .irq = {}, + .name = "locomo-spi", + .offset = LOCOMO_SPI, + .length = 0x30, + }, +}; + +static void locomo_handler(struct irq_desc *desc) +{ + struct locomo *lchip = irq_desc_get_handler_data(desc); + int req, i; + + /* Acknowledge the parent IRQ */ + desc->irq_data.chip->irq_ack(&desc->irq_data); + + /* check why this interrupt was generated */ + req = locomo_readl(lchip->base + LOCOMO_ICR) & 0x0f00; + + if (req) { + unsigned int irq; + + /* generate the next interrupt(s) */ + irq = lchip->irq_base; + for (i = 0; i <= 3; i++, irq++) { + if (req & (0x0100 << i)) { + generic_handle_irq(irq); + } + + } + } +} + +static void locomo_ack_irq(struct irq_data *d) +{ +} + +static void locomo_mask_irq(struct irq_data *d) +{ + struct locomo *lchip = irq_data_get_irq_chip_data(d); + unsigned int r; + r = locomo_readl(lchip->base + LOCOMO_ICR); + r &= ~(0x0010 << (d->irq - lchip->irq_base)); + locomo_writel(r, lchip->base + LOCOMO_ICR); +} + +static void locomo_unmask_irq(struct irq_data *d) +{ + struct locomo *lchip = irq_data_get_irq_chip_data(d); + unsigned int r; + r = locomo_readl(lchip->base + LOCOMO_ICR); + r |= (0x0010 << (d->irq - lchip->irq_base)); + locomo_writel(r, lchip->base + LOCOMO_ICR); +} + +static struct irq_chip locomo_chip = { + .name = "LOCOMO", + .irq_ack = locomo_ack_irq, + .irq_mask = locomo_mask_irq, + .irq_unmask = locomo_unmask_irq, +}; + +static void locomo_setup_irq(struct locomo *lchip) +{ + int irq = lchip->irq_base; + + /* + * Install handler for IRQ_LOCOMO_HW. + */ + irq_set_irq_type(lchip->irq, IRQ_TYPE_EDGE_FALLING); + irq_set_chained_handler_and_data(lchip->irq, locomo_handler, lchip); + + /* Install handlers for IRQ_LOCOMO_* */ + for ( ; irq <= lchip->irq_base + 3; irq++) { + irq_set_chip_and_handler(irq, &locomo_chip, handle_level_irq); + irq_set_chip_data(irq, lchip); + irq_clear_status_flags(irq, IRQ_NOREQUEST | IRQ_NOPROBE); + } +} + + +static void locomo_dev_release(struct device *_dev) +{ + struct locomo_dev *dev = LOCOMO_DEV(_dev); + + kfree(dev); +} + +static int +locomo_init_one_child(struct locomo *lchip, struct locomo_dev_info *info) +{ + struct locomo_dev *dev; + int ret; + + dev = kzalloc(sizeof(struct locomo_dev), GFP_KERNEL); + if (!dev) { + ret = -ENOMEM; + goto out; + } + + /* + * If the parent device has a DMA mask associated with it, + * propagate it down to the children. + */ + if (lchip->dev->dma_mask) { + dev->dma_mask = *lchip->dev->dma_mask; + dev->dev.dma_mask = &dev->dma_mask; + } + + dev_set_name(&dev->dev, "%s", info->name); + dev->devid = info->devid; + dev->dev.parent = lchip->dev; + dev->dev.bus = &locomo_bus_type; + dev->dev.release = locomo_dev_release; + dev->dev.coherent_dma_mask = lchip->dev->coherent_dma_mask; + + if (info->offset) + dev->mapbase = lchip->base + info->offset; + else + dev->mapbase = 0; + dev->length = info->length; + + dev->irq[0] = (lchip->irq_base == NO_IRQ) ? + NO_IRQ : lchip->irq_base + info->irq[0]; + + ret = device_register(&dev->dev); + if (ret) { + out: + kfree(dev); + } + return ret; +} + +#ifdef CONFIG_PM + +struct locomo_save_data { + u16 LCM_GPO; + u16 LCM_SPICT; + u16 LCM_GPE; + u16 LCM_ASD; + u16 LCM_SPIMD; +}; + +static int locomo_suspend(struct platform_device *dev, pm_message_t state) +{ + struct locomo *lchip = platform_get_drvdata(dev); + struct locomo_save_data *save; + unsigned long flags; + + save = kmalloc(sizeof(struct locomo_save_data), GFP_KERNEL); + if (!save) + return -ENOMEM; + + lchip->saved_state = save; + + spin_lock_irqsave(&lchip->lock, flags); + + save->LCM_GPO = locomo_readl(lchip->base + LOCOMO_GPO); /* GPIO */ + locomo_writel(0x00, lchip->base + LOCOMO_GPO); + save->LCM_SPICT = locomo_readl(lchip->base + LOCOMO_SPI + LOCOMO_SPICT); /* SPI */ + locomo_writel(0x40, lchip->base + LOCOMO_SPI + LOCOMO_SPICT); + save->LCM_GPE = locomo_readl(lchip->base + LOCOMO_GPE); /* GPIO */ + locomo_writel(0x00, lchip->base + LOCOMO_GPE); + save->LCM_ASD = locomo_readl(lchip->base + LOCOMO_ASD); /* ADSTART */ + locomo_writel(0x00, lchip->base + LOCOMO_ASD); + save->LCM_SPIMD = locomo_readl(lchip->base + LOCOMO_SPI + LOCOMO_SPIMD); /* SPI */ + locomo_writel(0x3C14, lchip->base + LOCOMO_SPI + LOCOMO_SPIMD); + + locomo_writel(0x00, lchip->base + LOCOMO_PAIF); + locomo_writel(0x00, lchip->base + LOCOMO_DAC); + locomo_writel(0x00, lchip->base + LOCOMO_BACKLIGHT + LOCOMO_TC); + + if ((locomo_readl(lchip->base + LOCOMO_LED + LOCOMO_LPT0) & 0x88) && (locomo_readl(lchip->base + LOCOMO_LED + LOCOMO_LPT1) & 0x88)) + locomo_writel(0x00, lchip->base + LOCOMO_C32K); /* CLK32 off */ + else + /* 18MHz already enabled, so no wait */ + locomo_writel(0xc1, lchip->base + LOCOMO_C32K); /* CLK32 on */ + + locomo_writel(0x00, lchip->base + LOCOMO_TADC); /* 18MHz clock off*/ + locomo_writel(0x00, lchip->base + LOCOMO_AUDIO + LOCOMO_ACC); /* 22MHz/24MHz clock off */ + locomo_writel(0x00, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS); /* FL */ + + spin_unlock_irqrestore(&lchip->lock, flags); + + return 0; +} + +static int locomo_resume(struct platform_device *dev) +{ + struct locomo *lchip = platform_get_drvdata(dev); + struct locomo_save_data *save; + unsigned long r; + unsigned long flags; + + save = lchip->saved_state; + if (!save) + return 0; + + spin_lock_irqsave(&lchip->lock, flags); + + locomo_writel(save->LCM_GPO, lchip->base + LOCOMO_GPO); + locomo_writel(save->LCM_SPICT, lchip->base + LOCOMO_SPI + LOCOMO_SPICT); + locomo_writel(save->LCM_GPE, lchip->base + LOCOMO_GPE); + locomo_writel(save->LCM_ASD, lchip->base + LOCOMO_ASD); + locomo_writel(save->LCM_SPIMD, lchip->base + LOCOMO_SPI + LOCOMO_SPIMD); + + locomo_writel(0x00, lchip->base + LOCOMO_C32K); + locomo_writel(0x90, lchip->base + LOCOMO_TADC); + + locomo_writel(0, lchip->base + LOCOMO_KEYBOARD + LOCOMO_KSC); + r = locomo_readl(lchip->base + LOCOMO_KEYBOARD + LOCOMO_KIC); + r &= 0xFEFF; + locomo_writel(r, lchip->base + LOCOMO_KEYBOARD + LOCOMO_KIC); + locomo_writel(0x1, lchip->base + LOCOMO_KEYBOARD + LOCOMO_KCMD); + + spin_unlock_irqrestore(&lchip->lock, flags); + + lchip->saved_state = NULL; + kfree(save); + + return 0; +} +#endif + + +/** + * locomo_probe - probe for a single LoCoMo chip. + * @phys_addr: physical address of device. + * + * Probe for a LoCoMo chip. This must be called + * before any other locomo-specific code. + * + * Returns: + * %-ENODEV device not found. + * %-EBUSY physical address already marked in-use. + * %0 successful. + */ +static int +__locomo_probe(struct device *me, struct resource *mem, int irq) +{ + struct locomo_platform_data *pdata = me->platform_data; + struct locomo *lchip; + unsigned long r; + int i, ret = -ENODEV; + + lchip = kzalloc(sizeof(struct locomo), GFP_KERNEL); + if (!lchip) + return -ENOMEM; + + spin_lock_init(&lchip->lock); + + lchip->dev = me; + dev_set_drvdata(lchip->dev, lchip); + + lchip->phys = mem->start; + lchip->irq = irq; + lchip->irq_base = (pdata) ? pdata->irq_base : NO_IRQ; + + /* + * Map the whole region. This also maps the + * registers for our children. + */ + lchip->base = ioremap(mem->start, PAGE_SIZE); + if (!lchip->base) { + ret = -ENOMEM; + goto out; + } + + /* locomo initialize */ + locomo_writel(0, lchip->base + LOCOMO_ICR); + /* KEYBOARD */ + locomo_writel(0, lchip->base + LOCOMO_KEYBOARD + LOCOMO_KIC); + + /* GPIO */ + locomo_writel(0, lchip->base + LOCOMO_GPO); + locomo_writel((LOCOMO_GPIO(1) | LOCOMO_GPIO(2) | LOCOMO_GPIO(13) | LOCOMO_GPIO(14)) + , lchip->base + LOCOMO_GPE); + locomo_writel((LOCOMO_GPIO(1) | LOCOMO_GPIO(2) | LOCOMO_GPIO(13) | LOCOMO_GPIO(14)) + , lchip->base + LOCOMO_GPD); + locomo_writel(0, lchip->base + LOCOMO_GIE); + + /* Frontlight */ + locomo_writel(0, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS); + locomo_writel(0, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALD); + + /* Longtime timer */ + locomo_writel(0, lchip->base + LOCOMO_LTINT); + /* SPI */ + locomo_writel(0, lchip->base + LOCOMO_SPI + LOCOMO_SPIIE); + + locomo_writel(6 + 8 + 320 + 30 - 10, lchip->base + LOCOMO_ASD); + r = locomo_readl(lchip->base + LOCOMO_ASD); + r |= 0x8000; + locomo_writel(r, lchip->base + LOCOMO_ASD); + + locomo_writel(6 + 8 + 320 + 30 - 10 - 128 + 4, lchip->base + LOCOMO_HSD); + r = locomo_readl(lchip->base + LOCOMO_HSD); + r |= 0x8000; + locomo_writel(r, lchip->base + LOCOMO_HSD); + + locomo_writel(128 / 8, lchip->base + LOCOMO_HSC); + + /* XON */ + locomo_writel(0x80, lchip->base + LOCOMO_TADC); + udelay(1000); + /* CLK9MEN */ + r = locomo_readl(lchip->base + LOCOMO_TADC); + r |= 0x10; + locomo_writel(r, lchip->base + LOCOMO_TADC); + udelay(100); + + /* init DAC */ + r = locomo_readl(lchip->base + LOCOMO_DAC); + r |= LOCOMO_DAC_SCLOEB | LOCOMO_DAC_SDAOEB; + locomo_writel(r, lchip->base + LOCOMO_DAC); + + r = locomo_readl(lchip->base + LOCOMO_VER); + printk(KERN_INFO "LoCoMo Chip: %lu%lu\n", (r >> 8), (r & 0xff)); + + /* + * The interrupt controller must be initialised before any + * other device to ensure that the interrupts are available. + */ + if (lchip->irq != NO_IRQ && lchip->irq_base != NO_IRQ) + locomo_setup_irq(lchip); + + for (i = 0; i < ARRAY_SIZE(locomo_devices); i++) + locomo_init_one_child(lchip, &locomo_devices[i]); + return 0; + + out: + kfree(lchip); + return ret; +} + +static int locomo_remove_child(struct device *dev, void *data) +{ + device_unregister(dev); + return 0; +} + +static void __locomo_remove(struct locomo *lchip) +{ + device_for_each_child(lchip->dev, NULL, locomo_remove_child); + + if (lchip->irq != NO_IRQ) { + irq_set_chained_handler_and_data(lchip->irq, NULL, NULL); + } + + iounmap(lchip->base); + kfree(lchip); +} + +static int locomo_probe(struct platform_device *dev) +{ + struct resource *mem; + int irq; + + mem = platform_get_resource(dev, IORESOURCE_MEM, 0); + if (!mem) + return -EINVAL; + irq = platform_get_irq(dev, 0); + if (irq < 0) + return -ENXIO; + + return __locomo_probe(&dev->dev, mem, irq); +} + +static int locomo_remove(struct platform_device *dev) +{ + struct locomo *lchip = platform_get_drvdata(dev); + + if (lchip) { + __locomo_remove(lchip); + platform_set_drvdata(dev, NULL); + } + + return 0; +} + +/* + * Not sure if this should be on the system bus or not yet. + * We really want some way to register a system device at + * the per-machine level, and then have this driver pick + * up the registered devices. + */ +static struct platform_driver locomo_device_driver = { + .probe = locomo_probe, + .remove = locomo_remove, +#ifdef CONFIG_PM + .suspend = locomo_suspend, + .resume = locomo_resume, +#endif + .driver = { + .name = "locomo", + }, +}; + +/* + * Get the parent device driver (us) structure + * from a child function device + */ +static inline struct locomo *locomo_chip_driver(struct locomo_dev *ldev) +{ + return (struct locomo *)dev_get_drvdata(ldev->dev.parent); +} + +void locomo_gpio_set_dir(struct device *dev, unsigned int bits, unsigned int dir) +{ + struct locomo *lchip = dev_get_drvdata(dev); + unsigned long flags; + unsigned int r; + + if (!lchip) + return; + + spin_lock_irqsave(&lchip->lock, flags); + + r = locomo_readl(lchip->base + LOCOMO_GPD); + if (dir) + r |= bits; + else + r &= ~bits; + locomo_writel(r, lchip->base + LOCOMO_GPD); + + r = locomo_readl(lchip->base + LOCOMO_GPE); + if (dir) + r |= bits; + else + r &= ~bits; + locomo_writel(r, lchip->base + LOCOMO_GPE); + + spin_unlock_irqrestore(&lchip->lock, flags); +} +EXPORT_SYMBOL(locomo_gpio_set_dir); + +int locomo_gpio_read_level(struct device *dev, unsigned int bits) +{ + struct locomo *lchip = dev_get_drvdata(dev); + unsigned long flags; + unsigned int ret; + + if (!lchip) + return -ENODEV; + + spin_lock_irqsave(&lchip->lock, flags); + ret = locomo_readl(lchip->base + LOCOMO_GPL); + spin_unlock_irqrestore(&lchip->lock, flags); + + ret &= bits; + return ret; +} +EXPORT_SYMBOL(locomo_gpio_read_level); + +int locomo_gpio_read_output(struct device *dev, unsigned int bits) +{ + struct locomo *lchip = dev_get_drvdata(dev); + unsigned long flags; + unsigned int ret; + + if (!lchip) + return -ENODEV; + + spin_lock_irqsave(&lchip->lock, flags); + ret = locomo_readl(lchip->base + LOCOMO_GPO); + spin_unlock_irqrestore(&lchip->lock, flags); + + ret &= bits; + return ret; +} +EXPORT_SYMBOL(locomo_gpio_read_output); + +void locomo_gpio_write(struct device *dev, unsigned int bits, unsigned int set) +{ + struct locomo *lchip = dev_get_drvdata(dev); + unsigned long flags; + unsigned int r; + + if (!lchip) + return; + + spin_lock_irqsave(&lchip->lock, flags); + + r = locomo_readl(lchip->base + LOCOMO_GPO); + if (set) + r |= bits; + else + r &= ~bits; + locomo_writel(r, lchip->base + LOCOMO_GPO); + + spin_unlock_irqrestore(&lchip->lock, flags); +} +EXPORT_SYMBOL(locomo_gpio_write); + +static void locomo_m62332_sendbit(void *mapbase, int bit) +{ + unsigned int r; + + r = locomo_readl(mapbase + LOCOMO_DAC); + r &= ~(LOCOMO_DAC_SCLOEB); + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ + udelay(DAC_DATA_HOLD_TIME); /* 300 nsec */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r &= ~(LOCOMO_DAC_SCLOEB); + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ + udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ + + if (bit & 1) { + r = locomo_readl(mapbase + LOCOMO_DAC); + r |= LOCOMO_DAC_SDAOEB; + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ + } else { + r = locomo_readl(mapbase + LOCOMO_DAC); + r &= ~(LOCOMO_DAC_SDAOEB); + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ + } + + udelay(DAC_DATA_SETUP_TIME); /* 250 nsec */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r |= LOCOMO_DAC_SCLOEB; + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ + udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.0 usec */ +} + +void locomo_m62332_senddata(struct locomo_dev *ldev, unsigned int dac_data, int channel) +{ + struct locomo *lchip = locomo_chip_driver(ldev); + int i; + unsigned char data; + unsigned int r; + void *mapbase = lchip->base; + unsigned long flags; + + spin_lock_irqsave(&lchip->lock, flags); + + /* Start */ + udelay(DAC_BUS_FREE_TIME); /* 5.0 usec */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r |= LOCOMO_DAC_SCLOEB | LOCOMO_DAC_SDAOEB; + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ + udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.0 usec */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r &= ~(LOCOMO_DAC_SDAOEB); + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_START_HOLD_TIME); /* 5.0 usec */ + udelay(DAC_DATA_HOLD_TIME); /* 300 nsec */ + + /* Send slave address and W bit (LSB is W bit) */ + data = (M62332_SLAVE_ADDR << 1) | M62332_W_BIT; + for (i = 1; i <= 8; i++) { + locomo_m62332_sendbit(mapbase, data >> (8 - i)); + } + + /* Check A bit */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r &= ~(LOCOMO_DAC_SCLOEB); + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ + udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r &= ~(LOCOMO_DAC_SDAOEB); + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r |= LOCOMO_DAC_SCLOEB; + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ + udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.7 usec */ + if (locomo_readl(mapbase + LOCOMO_DAC) & LOCOMO_DAC_SDAOEB) { /* High is error */ + printk(KERN_WARNING "locomo: m62332_senddata Error 1\n"); + goto out; + } + + /* Send Sub address (LSB is channel select) */ + /* channel = 0 : ch1 select */ + /* = 1 : ch2 select */ + data = M62332_SUB_ADDR + channel; + for (i = 1; i <= 8; i++) { + locomo_m62332_sendbit(mapbase, data >> (8 - i)); + } + + /* Check A bit */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r &= ~(LOCOMO_DAC_SCLOEB); + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ + udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r &= ~(LOCOMO_DAC_SDAOEB); + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r |= LOCOMO_DAC_SCLOEB; + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ + udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.7 usec */ + if (locomo_readl(mapbase + LOCOMO_DAC) & LOCOMO_DAC_SDAOEB) { /* High is error */ + printk(KERN_WARNING "locomo: m62332_senddata Error 2\n"); + goto out; + } + + /* Send DAC data */ + for (i = 1; i <= 8; i++) { + locomo_m62332_sendbit(mapbase, dac_data >> (8 - i)); + } + + /* Check A bit */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r &= ~(LOCOMO_DAC_SCLOEB); + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ + udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r &= ~(LOCOMO_DAC_SDAOEB); + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r |= LOCOMO_DAC_SCLOEB; + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ + udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.7 usec */ + if (locomo_readl(mapbase + LOCOMO_DAC) & LOCOMO_DAC_SDAOEB) { /* High is error */ + printk(KERN_WARNING "locomo: m62332_senddata Error 3\n"); + } + +out: + /* stop */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r &= ~(LOCOMO_DAC_SCLOEB); + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ + udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r |= LOCOMO_DAC_SCLOEB; + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ + udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4 usec */ + r = locomo_readl(mapbase + LOCOMO_DAC); + r |= LOCOMO_DAC_SDAOEB; + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ + udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4 usec */ + + r = locomo_readl(mapbase + LOCOMO_DAC); + r |= LOCOMO_DAC_SCLOEB | LOCOMO_DAC_SDAOEB; + locomo_writel(r, mapbase + LOCOMO_DAC); + udelay(DAC_LOW_SETUP_TIME); /* 1000 nsec */ + udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ + + spin_unlock_irqrestore(&lchip->lock, flags); +} +EXPORT_SYMBOL(locomo_m62332_senddata); + +/* + * Frontlight control + */ + +void locomo_frontlight_set(struct locomo_dev *dev, int duty, int vr, int bpwf) +{ + unsigned long flags; + struct locomo *lchip = locomo_chip_driver(dev); + + if (vr) + locomo_gpio_write(dev->dev.parent, LOCOMO_GPIO_FL_VR, 1); + else + locomo_gpio_write(dev->dev.parent, LOCOMO_GPIO_FL_VR, 0); + + spin_lock_irqsave(&lchip->lock, flags); + locomo_writel(bpwf, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS); + udelay(100); + locomo_writel(duty, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALD); + locomo_writel(bpwf | LOCOMO_ALC_EN, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS); + spin_unlock_irqrestore(&lchip->lock, flags); +} +EXPORT_SYMBOL(locomo_frontlight_set); + +/* + * LoCoMo "Register Access Bus." + * + * We model this as a regular bus type, and hang devices directly + * off this. + */ +static int locomo_match(struct device *_dev, struct device_driver *_drv) +{ + struct locomo_dev *dev = LOCOMO_DEV(_dev); + struct locomo_driver *drv = LOCOMO_DRV(_drv); + + return dev->devid == drv->devid; +} + +static int locomo_bus_probe(struct device *dev) +{ + struct locomo_dev *ldev = LOCOMO_DEV(dev); + struct locomo_driver *drv = LOCOMO_DRV(dev->driver); + int ret = -ENODEV; + + if (drv->probe) + ret = drv->probe(ldev); + return ret; +} + +static void locomo_bus_remove(struct device *dev) +{ + struct locomo_dev *ldev = LOCOMO_DEV(dev); + struct locomo_driver *drv = LOCOMO_DRV(dev->driver); + + if (drv->remove) + drv->remove(ldev); +} + +struct bus_type locomo_bus_type = { + .name = "locomo-bus", + .match = locomo_match, + .probe = locomo_bus_probe, + .remove = locomo_bus_remove, +}; + +int locomo_driver_register(struct locomo_driver *driver) +{ + driver->drv.bus = &locomo_bus_type; + return driver_register(&driver->drv); +} +EXPORT_SYMBOL(locomo_driver_register); + +void locomo_driver_unregister(struct locomo_driver *driver) +{ + driver_unregister(&driver->drv); +} +EXPORT_SYMBOL(locomo_driver_unregister); + +static int __init locomo_init(void) +{ + int ret = bus_register(&locomo_bus_type); + if (ret == 0) + platform_driver_register(&locomo_device_driver); + return ret; +} + +static void __exit locomo_exit(void) +{ + platform_driver_unregister(&locomo_device_driver); + bus_unregister(&locomo_bus_type); +} + +module_init(locomo_init); +module_exit(locomo_exit); + +MODULE_DESCRIPTION("Sharp LoCoMo core driver"); +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("John Lenz <lenz@cs.wisc.edu>"); |