diff options
Diffstat (limited to 'drivers/ata/ahci.h')
| -rw-r--r-- | drivers/ata/ahci.h | 457 |
1 files changed, 457 insertions, 0 deletions
diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h new file mode 100644 index 000000000..ff8e6ae1c --- /dev/null +++ b/drivers/ata/ahci.h @@ -0,0 +1,457 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ +/* + * ahci.h - Common AHCI SATA definitions and declarations + * + * Maintained by: Tejun Heo <tj@kernel.org> + * Please ALWAYS copy linux-ide@vger.kernel.org + * on emails. + * + * Copyright 2004-2005 Red Hat, Inc. + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/driver-api/libata.rst + * + * AHCI hardware documentation: + * http://www.intel.com/technology/serialata/pdf/rev1_0.pdf + * http://www.intel.com/technology/serialata/pdf/rev1_1.pdf + */ + +#ifndef _AHCI_H +#define _AHCI_H + +#include <linux/pci.h> +#include <linux/clk.h> +#include <linux/libata.h> +#include <linux/phy/phy.h> +#include <linux/regulator/consumer.h> +#include <linux/bits.h> + +/* Enclosure Management Control */ +#define EM_CTRL_MSG_TYPE 0x000f0000 + +/* Enclosure Management LED Message Type */ +#define EM_MSG_LED_HBA_PORT 0x0000000f +#define EM_MSG_LED_PMP_SLOT 0x0000ff00 +#define EM_MSG_LED_VALUE 0xffff0000 +#define EM_MSG_LED_VALUE_ACTIVITY 0x00070000 +#define EM_MSG_LED_VALUE_OFF 0xfff80000 +#define EM_MSG_LED_VALUE_ON 0x00010000 + +enum { + AHCI_MAX_PORTS = 32, + AHCI_MAX_SG = 168, /* hardware max is 64K */ + AHCI_DMA_BOUNDARY = 0xffffffff, + AHCI_MAX_CMDS = 32, + AHCI_CMD_SZ = 32, + AHCI_CMD_SLOT_SZ = AHCI_MAX_CMDS * AHCI_CMD_SZ, + AHCI_RX_FIS_SZ = 256, + AHCI_CMD_TBL_CDB = 0x40, + AHCI_CMD_TBL_HDR_SZ = 0x80, + AHCI_CMD_TBL_SZ = AHCI_CMD_TBL_HDR_SZ + (AHCI_MAX_SG * 16), + AHCI_CMD_TBL_AR_SZ = AHCI_CMD_TBL_SZ * AHCI_MAX_CMDS, + AHCI_PORT_PRIV_DMA_SZ = AHCI_CMD_SLOT_SZ + AHCI_CMD_TBL_AR_SZ + + AHCI_RX_FIS_SZ, + AHCI_PORT_PRIV_FBS_DMA_SZ = AHCI_CMD_SLOT_SZ + + AHCI_CMD_TBL_AR_SZ + + (AHCI_RX_FIS_SZ * 16), + AHCI_IRQ_ON_SG = BIT(31), + AHCI_CMD_ATAPI = BIT(5), + AHCI_CMD_WRITE = BIT(6), + AHCI_CMD_PREFETCH = BIT(7), + AHCI_CMD_RESET = BIT(8), + AHCI_CMD_CLR_BUSY = BIT(10), + + RX_FIS_PIO_SETUP = 0x20, /* offset of PIO Setup FIS data */ + RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */ + RX_FIS_SDB = 0x58, /* offset of SDB FIS data */ + RX_FIS_UNK = 0x60, /* offset of Unknown FIS data */ + + /* global controller registers */ + HOST_CAP = 0x00, /* host capabilities */ + HOST_CTL = 0x04, /* global host control */ + HOST_IRQ_STAT = 0x08, /* interrupt status */ + HOST_PORTS_IMPL = 0x0c, /* bitmap of implemented ports */ + HOST_VERSION = 0x10, /* AHCI spec. version compliancy */ + HOST_EM_LOC = 0x1c, /* Enclosure Management location */ + HOST_EM_CTL = 0x20, /* Enclosure Management Control */ + HOST_CAP2 = 0x24, /* host capabilities, extended */ + + /* HOST_CTL bits */ + HOST_RESET = BIT(0), /* reset controller; self-clear */ + HOST_IRQ_EN = BIT(1), /* global IRQ enable */ + HOST_MRSM = BIT(2), /* MSI Revert to Single Message */ + HOST_AHCI_EN = BIT(31), /* AHCI enabled */ + + /* HOST_CAP bits */ + HOST_CAP_SXS = BIT(5), /* Supports External SATA */ + HOST_CAP_EMS = BIT(6), /* Enclosure Management support */ + HOST_CAP_CCC = BIT(7), /* Command Completion Coalescing */ + HOST_CAP_PART = BIT(13), /* Partial state capable */ + HOST_CAP_SSC = BIT(14), /* Slumber state capable */ + HOST_CAP_PIO_MULTI = BIT(15), /* PIO multiple DRQ support */ + HOST_CAP_FBS = BIT(16), /* FIS-based switching support */ + HOST_CAP_PMP = BIT(17), /* Port Multiplier support */ + HOST_CAP_ONLY = BIT(18), /* Supports AHCI mode only */ + HOST_CAP_CLO = BIT(24), /* Command List Override support */ + HOST_CAP_LED = BIT(25), /* Supports activity LED */ + HOST_CAP_ALPM = BIT(26), /* Aggressive Link PM support */ + HOST_CAP_SSS = BIT(27), /* Staggered Spin-up */ + HOST_CAP_MPS = BIT(28), /* Mechanical presence switch */ + HOST_CAP_SNTF = BIT(29), /* SNotification register */ + HOST_CAP_NCQ = BIT(30), /* Native Command Queueing */ + HOST_CAP_64 = BIT(31), /* PCI DAC (64-bit DMA) support */ + + /* HOST_CAP2 bits */ + HOST_CAP2_BOH = BIT(0), /* BIOS/OS handoff supported */ + HOST_CAP2_NVMHCI = BIT(1), /* NVMHCI supported */ + HOST_CAP2_APST = BIT(2), /* Automatic partial to slumber */ + HOST_CAP2_SDS = BIT(3), /* Support device sleep */ + HOST_CAP2_SADM = BIT(4), /* Support aggressive DevSlp */ + HOST_CAP2_DESO = BIT(5), /* DevSlp from slumber only */ + + /* registers for each SATA port */ + PORT_LST_ADDR = 0x00, /* command list DMA addr */ + PORT_LST_ADDR_HI = 0x04, /* command list DMA addr hi */ + PORT_FIS_ADDR = 0x08, /* FIS rx buf addr */ + PORT_FIS_ADDR_HI = 0x0c, /* FIS rx buf addr hi */ + PORT_IRQ_STAT = 0x10, /* interrupt status */ + PORT_IRQ_MASK = 0x14, /* interrupt enable/disable mask */ + PORT_CMD = 0x18, /* port command */ + PORT_TFDATA = 0x20, /* taskfile data */ + PORT_SIG = 0x24, /* device TF signature */ + PORT_CMD_ISSUE = 0x38, /* command issue */ + PORT_SCR_STAT = 0x28, /* SATA phy register: SStatus */ + PORT_SCR_CTL = 0x2c, /* SATA phy register: SControl */ + PORT_SCR_ERR = 0x30, /* SATA phy register: SError */ + PORT_SCR_ACT = 0x34, /* SATA phy register: SActive */ + PORT_SCR_NTF = 0x3c, /* SATA phy register: SNotification */ + PORT_FBS = 0x40, /* FIS-based Switching */ + PORT_DEVSLP = 0x44, /* device sleep */ + + /* PORT_IRQ_{STAT,MASK} bits */ + PORT_IRQ_COLD_PRES = BIT(31), /* cold presence detect */ + PORT_IRQ_TF_ERR = BIT(30), /* task file error */ + PORT_IRQ_HBUS_ERR = BIT(29), /* host bus fatal error */ + PORT_IRQ_HBUS_DATA_ERR = BIT(28), /* host bus data error */ + PORT_IRQ_IF_ERR = BIT(27), /* interface fatal error */ + PORT_IRQ_IF_NONFATAL = BIT(26), /* interface non-fatal error */ + PORT_IRQ_OVERFLOW = BIT(24), /* xfer exhausted available S/G */ + PORT_IRQ_BAD_PMP = BIT(23), /* incorrect port multiplier */ + + PORT_IRQ_PHYRDY = BIT(22), /* PhyRdy changed */ + PORT_IRQ_DMPS = BIT(7), /* mechanical presence status */ + PORT_IRQ_CONNECT = BIT(6), /* port connect change status */ + PORT_IRQ_SG_DONE = BIT(5), /* descriptor processed */ + PORT_IRQ_UNK_FIS = BIT(4), /* unknown FIS rx'd */ + PORT_IRQ_SDB_FIS = BIT(3), /* Set Device Bits FIS rx'd */ + PORT_IRQ_DMAS_FIS = BIT(2), /* DMA Setup FIS rx'd */ + PORT_IRQ_PIOS_FIS = BIT(1), /* PIO Setup FIS rx'd */ + PORT_IRQ_D2H_REG_FIS = BIT(0), /* D2H Register FIS rx'd */ + + PORT_IRQ_FREEZE = PORT_IRQ_HBUS_ERR | + PORT_IRQ_IF_ERR | + PORT_IRQ_CONNECT | + PORT_IRQ_PHYRDY | + PORT_IRQ_UNK_FIS | + PORT_IRQ_BAD_PMP, + PORT_IRQ_ERROR = PORT_IRQ_FREEZE | + PORT_IRQ_TF_ERR | + PORT_IRQ_HBUS_DATA_ERR, + DEF_PORT_IRQ = PORT_IRQ_ERROR | PORT_IRQ_SG_DONE | + PORT_IRQ_SDB_FIS | PORT_IRQ_DMAS_FIS | + PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS, + + /* PORT_CMD bits */ + PORT_CMD_ASP = BIT(27), /* Aggressive Slumber/Partial */ + PORT_CMD_ALPE = BIT(26), /* Aggressive Link PM enable */ + PORT_CMD_ATAPI = BIT(24), /* Device is ATAPI */ + PORT_CMD_FBSCP = BIT(22), /* FBS Capable Port */ + PORT_CMD_ESP = BIT(21), /* External Sata Port */ + PORT_CMD_CPD = BIT(20), /* Cold Presence Detection */ + PORT_CMD_MPSP = BIT(19), /* Mechanical Presence Switch */ + PORT_CMD_HPCP = BIT(18), /* HotPlug Capable Port */ + PORT_CMD_PMP = BIT(17), /* PMP attached */ + PORT_CMD_LIST_ON = BIT(15), /* cmd list DMA engine running */ + PORT_CMD_FIS_ON = BIT(14), /* FIS DMA engine running */ + PORT_CMD_FIS_RX = BIT(4), /* Enable FIS receive DMA engine */ + PORT_CMD_CLO = BIT(3), /* Command list override */ + PORT_CMD_POWER_ON = BIT(2), /* Power up device */ + PORT_CMD_SPIN_UP = BIT(1), /* Spin up device */ + PORT_CMD_START = BIT(0), /* Enable port DMA engine */ + + PORT_CMD_ICC_MASK = (0xfu << 28), /* i/f ICC state mask */ + PORT_CMD_ICC_ACTIVE = (0x1u << 28), /* Put i/f in active state */ + PORT_CMD_ICC_PARTIAL = (0x2u << 28), /* Put i/f in partial state */ + PORT_CMD_ICC_SLUMBER = (0x6u << 28), /* Put i/f in slumber state */ + + /* PORT_CMD capabilities mask */ + PORT_CMD_CAP = PORT_CMD_HPCP | PORT_CMD_MPSP | + PORT_CMD_CPD | PORT_CMD_ESP | PORT_CMD_FBSCP, + + /* PORT_FBS bits */ + PORT_FBS_DWE_OFFSET = 16, /* FBS device with error offset */ + PORT_FBS_ADO_OFFSET = 12, /* FBS active dev optimization offset */ + PORT_FBS_DEV_OFFSET = 8, /* FBS device to issue offset */ + PORT_FBS_DEV_MASK = (0xf << PORT_FBS_DEV_OFFSET), /* FBS.DEV */ + PORT_FBS_SDE = BIT(2), /* FBS single device error */ + PORT_FBS_DEC = BIT(1), /* FBS device error clear */ + PORT_FBS_EN = BIT(0), /* Enable FBS */ + + /* PORT_DEVSLP bits */ + PORT_DEVSLP_DM_OFFSET = 25, /* DITO multiplier offset */ + PORT_DEVSLP_DM_MASK = (0xf << 25), /* DITO multiplier mask */ + PORT_DEVSLP_DITO_OFFSET = 15, /* DITO offset */ + PORT_DEVSLP_MDAT_OFFSET = 10, /* Minimum assertion time */ + PORT_DEVSLP_DETO_OFFSET = 2, /* DevSlp exit timeout */ + PORT_DEVSLP_DSP = BIT(1), /* DevSlp present */ + PORT_DEVSLP_ADSE = BIT(0), /* Aggressive DevSlp enable */ + + /* hpriv->flags bits */ + +#define AHCI_HFLAGS(flags) .private_data = (void *)(flags) + + AHCI_HFLAG_NO_NCQ = BIT(0), + AHCI_HFLAG_IGN_IRQ_IF_ERR = BIT(1), /* ignore IRQ_IF_ERR */ + AHCI_HFLAG_IGN_SERR_INTERNAL = BIT(2), /* ignore SERR_INTERNAL */ + AHCI_HFLAG_32BIT_ONLY = BIT(3), /* force 32bit */ + AHCI_HFLAG_MV_PATA = BIT(4), /* PATA port */ + AHCI_HFLAG_NO_MSI = BIT(5), /* no PCI MSI */ + AHCI_HFLAG_NO_PMP = BIT(6), /* no PMP */ + AHCI_HFLAG_SECT255 = BIT(8), /* max 255 sectors */ + AHCI_HFLAG_YES_NCQ = BIT(9), /* force NCQ cap on */ + AHCI_HFLAG_NO_SUSPEND = BIT(10), /* don't suspend */ + AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = BIT(11), /* treat SRST timeout as + link offline */ + AHCI_HFLAG_NO_SNTF = BIT(12), /* no sntf */ + AHCI_HFLAG_NO_FPDMA_AA = BIT(13), /* no FPDMA AA */ + AHCI_HFLAG_YES_FBS = BIT(14), /* force FBS cap on */ + AHCI_HFLAG_DELAY_ENGINE = BIT(15), /* do not start engine on + port start (wait until + error-handling stage) */ + AHCI_HFLAG_NO_DEVSLP = BIT(17), /* no device sleep */ + AHCI_HFLAG_NO_FBS = BIT(18), /* no FBS */ + +#ifdef CONFIG_PCI_MSI + AHCI_HFLAG_MULTI_MSI = BIT(20), /* per-port MSI(-X) */ +#else + /* compile out MSI infrastructure */ + AHCI_HFLAG_MULTI_MSI = 0, +#endif + AHCI_HFLAG_WAKE_BEFORE_STOP = BIT(22), /* wake before DMA stop */ + AHCI_HFLAG_YES_ALPM = BIT(23), /* force ALPM cap on */ + AHCI_HFLAG_NO_WRITE_TO_RO = BIT(24), /* don't write to read + only registers */ + AHCI_HFLAG_USE_LPM_POLICY = BIT(25), /* chipset that should use + SATA_MOBILE_LPM_POLICY + as default lpm_policy */ + AHCI_HFLAG_SUSPEND_PHYS = BIT(26), /* handle PHYs during + suspend/resume */ + AHCI_HFLAG_NO_SXS = BIT(28), /* SXS not supported */ + + /* ap->flags bits */ + + AHCI_FLAG_COMMON = ATA_FLAG_SATA | ATA_FLAG_PIO_DMA | + ATA_FLAG_ACPI_SATA | ATA_FLAG_AN, + + ICH_MAP = 0x90, /* ICH MAP register */ + PCS_6 = 0x92, /* 6 port PCS */ + PCS_7 = 0x94, /* 7+ port PCS (Denverton) */ + + /* em constants */ + EM_MAX_SLOTS = SATA_PMP_MAX_PORTS, + EM_MAX_RETRY = 5, + + /* em_ctl bits */ + EM_CTL_RST = BIT(9), /* Reset */ + EM_CTL_TM = BIT(8), /* Transmit Message */ + EM_CTL_MR = BIT(0), /* Message Received */ + EM_CTL_ALHD = BIT(26), /* Activity LED */ + EM_CTL_XMT = BIT(25), /* Transmit Only */ + EM_CTL_SMB = BIT(24), /* Single Message Buffer */ + EM_CTL_SGPIO = BIT(19), /* SGPIO messages supported */ + EM_CTL_SES = BIT(18), /* SES-2 messages supported */ + EM_CTL_SAFTE = BIT(17), /* SAF-TE messages supported */ + EM_CTL_LED = BIT(16), /* LED messages supported */ + + /* em message type */ + EM_MSG_TYPE_LED = BIT(0), /* LED */ + EM_MSG_TYPE_SAFTE = BIT(1), /* SAF-TE */ + EM_MSG_TYPE_SES2 = BIT(2), /* SES-2 */ + EM_MSG_TYPE_SGPIO = BIT(3), /* SGPIO */ +}; + +struct ahci_cmd_hdr { + __le32 opts; + __le32 status; + __le32 tbl_addr; + __le32 tbl_addr_hi; + __le32 reserved[4]; +}; + +struct ahci_sg { + __le32 addr; + __le32 addr_hi; + __le32 reserved; + __le32 flags_size; +}; + +struct ahci_em_priv { + enum sw_activity blink_policy; + struct timer_list timer; + unsigned long saved_activity; + unsigned long activity; + unsigned long led_state; + struct ata_link *link; +}; + +struct ahci_port_priv { + struct ata_link *active_link; + struct ahci_cmd_hdr *cmd_slot; + dma_addr_t cmd_slot_dma; + void *cmd_tbl; + dma_addr_t cmd_tbl_dma; + void *rx_fis; + dma_addr_t rx_fis_dma; + /* for NCQ spurious interrupt analysis */ + unsigned int ncq_saw_d2h:1; + unsigned int ncq_saw_dmas:1; + unsigned int ncq_saw_sdb:1; + spinlock_t lock; /* protects parent ata_port */ + u32 intr_mask; /* interrupts to enable */ + bool fbs_supported; /* set iff FBS is supported */ + bool fbs_enabled; /* set iff FBS is enabled */ + int fbs_last_dev; /* save FBS.DEV of last FIS */ + /* enclosure management info per PM slot */ + struct ahci_em_priv em_priv[EM_MAX_SLOTS]; + char *irq_desc; /* desc in /proc/interrupts */ +}; + +struct ahci_host_priv { + /* Input fields */ + unsigned int flags; /* AHCI_HFLAG_* */ + u32 mask_port_map; /* mask out particular bits */ + + void __iomem * mmio; /* bus-independent mem map */ + u32 cap; /* cap to use */ + u32 cap2; /* cap2 to use */ + u32 version; /* cached version */ + u32 port_map; /* port map to use */ + u32 saved_cap; /* saved initial cap */ + u32 saved_cap2; /* saved initial cap2 */ + u32 saved_port_map; /* saved initial port_map */ + u32 saved_port_cap[AHCI_MAX_PORTS]; /* saved port_cap */ + u32 em_loc; /* enclosure management location */ + u32 em_buf_sz; /* EM buffer size in byte */ + u32 em_msg_type; /* EM message type */ + u32 remapped_nvme; /* NVMe remapped device count */ + bool got_runtime_pm; /* Did we do pm_runtime_get? */ + unsigned int n_clks; + struct clk_bulk_data *clks; /* Optional */ + unsigned int f_rsts; + struct reset_control *rsts; /* Optional */ + struct regulator **target_pwrs; /* Optional */ + struct regulator *ahci_regulator;/* Optional */ + struct regulator *phy_regulator;/* Optional */ + /* + * If platform uses PHYs. There is a 1:1 relation between the port number and + * the PHY position in this array. + */ + struct phy **phys; + unsigned nports; /* Number of ports */ + void *plat_data; /* Other platform data */ + unsigned int irq; /* interrupt line */ + /* + * Optional ahci_start_engine override, if not set this gets set to the + * default ahci_start_engine during ahci_save_initial_config, this can + * be overridden anytime before the host is activated. + */ + void (*start_engine)(struct ata_port *ap); + /* + * Optional ahci_stop_engine override, if not set this gets set to the + * default ahci_stop_engine during ahci_save_initial_config, this can + * be overridden anytime before the host is activated. + */ + int (*stop_engine)(struct ata_port *ap); + + irqreturn_t (*irq_handler)(int irq, void *dev_instance); + + /* only required for per-port MSI(-X) support */ + int (*get_irq_vector)(struct ata_host *host, + int port); +}; + +extern int ahci_ignore_sss; + +extern const struct attribute_group *ahci_shost_groups[]; +extern const struct attribute_group *ahci_sdev_groups[]; + +/* + * This must be instantiated by the edge drivers. Read the comments + * for ATA_BASE_SHT + */ +#define AHCI_SHT(drv_name) \ + __ATA_BASE_SHT(drv_name), \ + .can_queue = AHCI_MAX_CMDS, \ + .sg_tablesize = AHCI_MAX_SG, \ + .dma_boundary = AHCI_DMA_BOUNDARY, \ + .shost_groups = ahci_shost_groups, \ + .sdev_groups = ahci_sdev_groups, \ + .change_queue_depth = ata_scsi_change_queue_depth, \ + .tag_alloc_policy = BLK_TAG_ALLOC_RR, \ + .slave_configure = ata_scsi_slave_config + +extern struct ata_port_operations ahci_ops; +extern struct ata_port_operations ahci_platform_ops; +extern struct ata_port_operations ahci_pmp_retry_srst_ops; + +unsigned int ahci_dev_classify(struct ata_port *ap); +void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag, + u32 opts); +void ahci_save_initial_config(struct device *dev, + struct ahci_host_priv *hpriv); +void ahci_init_controller(struct ata_host *host); +int ahci_reset_controller(struct ata_host *host); + +int ahci_do_softreset(struct ata_link *link, unsigned int *class, + int pmp, unsigned long deadline, + int (*check_ready)(struct ata_link *link)); + +int ahci_do_hardreset(struct ata_link *link, unsigned int *class, + unsigned long deadline, bool *online); + +unsigned int ahci_qc_issue(struct ata_queued_cmd *qc); +int ahci_stop_engine(struct ata_port *ap); +void ahci_start_fis_rx(struct ata_port *ap); +void ahci_start_engine(struct ata_port *ap); +int ahci_check_ready(struct ata_link *link); +int ahci_kick_engine(struct ata_port *ap); +int ahci_port_resume(struct ata_port *ap); +void ahci_set_em_messages(struct ahci_host_priv *hpriv, + struct ata_port_info *pi); +int ahci_reset_em(struct ata_host *host); +void ahci_print_info(struct ata_host *host, const char *scc_s); +int ahci_host_activate(struct ata_host *host, struct scsi_host_template *sht); +void ahci_error_handler(struct ata_port *ap); +u32 ahci_handle_port_intr(struct ata_host *host, u32 irq_masked); + +static inline void __iomem *__ahci_port_base(struct ahci_host_priv *hpriv, + unsigned int port_no) +{ + void __iomem *mmio = hpriv->mmio; + + return mmio + 0x100 + (port_no * 0x80); +} + +static inline void __iomem *ahci_port_base(struct ata_port *ap) +{ + struct ahci_host_priv *hpriv = ap->host->private_data; + + return __ahci_port_base(hpriv, ap->port_no); +} + +static inline int ahci_nr_ports(u32 cap) +{ + return (cap & 0x1f) + 1; +} + +#endif /* _AHCI_H */ |