diff options
Diffstat (limited to 'drivers/ata/pata_jmicron.c')
| -rw-r--r-- | drivers/ata/pata_jmicron.c | 174 |
1 files changed, 174 insertions, 0 deletions
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c new file mode 100644 index 000000000..d1b3ce895 --- /dev/null +++ b/drivers/ata/pata_jmicron.c @@ -0,0 +1,174 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * pata_jmicron.c - JMicron ATA driver for non AHCI mode. This drives the + * PATA port of the controller. The SATA ports are + * driven by AHCI in the usual configuration although + * this driver can handle other setups if we need it. + * + * (c) 2006 Red Hat + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/ata.h> + +#define DRV_NAME "pata_jmicron" +#define DRV_VERSION "0.1.5" + +typedef enum { + PORT_PATA0 = 0, + PORT_PATA1 = 1, + PORT_SATA = 2, +} port_type; + +/** + * jmicron_pre_reset - check for 40/80 pin + * @link: ATA link + * @deadline: deadline jiffies for the operation + * + * Perform the PATA port setup we need. + * + * On the Jmicron 361/363 there is a single PATA port that can be mapped + * either as primary or secondary (or neither). We don't do any policy + * and setup here. We assume that has been done by init_one and the + * BIOS. + */ +static int jmicron_pre_reset(struct ata_link *link, unsigned long deadline) +{ + struct ata_port *ap = link->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 control; + u32 control5; + int port_mask = 1<< (4 * ap->port_no); + int port = ap->port_no; + port_type port_map[2]; + + /* Check if our port is enabled */ + pci_read_config_dword(pdev, 0x40, &control); + if ((control & port_mask) == 0) + return -ENOENT; + + /* There are two basic mappings. One has the two SATA ports merged + as master/slave and the secondary as PATA, the other has only the + SATA port mapped */ + if (control & (1 << 23)) { + port_map[0] = PORT_SATA; + port_map[1] = PORT_PATA0; + } else { + port_map[0] = PORT_SATA; + port_map[1] = PORT_SATA; + } + + /* The 365/366 may have this bit set to map the second PATA port + as the internal primary channel */ + pci_read_config_dword(pdev, 0x80, &control5); + if (control5 & (1<<24)) + port_map[0] = PORT_PATA1; + + /* The two ports may then be logically swapped by the firmware */ + if (control & (1 << 22)) + port = port ^ 1; + + /* + * Now we know which physical port we are talking about we can + * actually do our cable checking etc. Thankfully we don't need + * to do the plumbing for other cases. + */ + switch (port_map[port]) { + case PORT_PATA0: + if ((control & (1 << 5)) == 0) + return -ENOENT; + if (control & (1 << 3)) /* 40/80 pin primary */ + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + break; + case PORT_PATA1: + /* Bit 21 is set if the port is enabled */ + if ((control5 & (1 << 21)) == 0) + return -ENOENT; + if (control5 & (1 << 19)) /* 40/80 pin secondary */ + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + break; + case PORT_SATA: + ap->cbl = ATA_CBL_SATA; + break; + } + return ata_sff_prereset(link, deadline); +} + +/* No PIO or DMA methods needed for this device */ + +static struct scsi_host_template jmicron_sht = { + ATA_BMDMA_SHT(DRV_NAME), +}; + +static struct ata_port_operations jmicron_ops = { + .inherits = &ata_bmdma_port_ops, + .prereset = jmicron_pre_reset, +}; + + +/** + * jmicron_init_one - Register Jmicron ATA PCI device with kernel services + * @pdev: PCI device to register + * @id: PCI device ID + * + * Called from kernel PCI layer. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *id) +{ + static const struct ata_port_info info = { + .flags = ATA_FLAG_SLAVE_POSS, + + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA5, + + .port_ops = &jmicron_ops, + }; + const struct ata_port_info *ppi[] = { &info, NULL }; + + return ata_pci_bmdma_init_one(pdev, ppi, &jmicron_sht, NULL, 0); +} + +static const struct pci_device_id jmicron_pci_tbl[] = { + { PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, + PCI_CLASS_STORAGE_IDE << 8, 0xffff00, 0 }, + { } /* terminate list */ +}; + +static struct pci_driver jmicron_pci_driver = { + .name = DRV_NAME, + .id_table = jmicron_pci_tbl, + .probe = jmicron_init_one, + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM_SLEEP + .suspend = ata_pci_device_suspend, + .resume = ata_pci_device_resume, +#endif +}; + +module_pci_driver(jmicron_pci_driver); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("SCSI low-level driver for Jmicron PATA ports"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, jmicron_pci_tbl); +MODULE_VERSION(DRV_VERSION); + |