diff options
Diffstat (limited to 'drivers/hwmon/pmbus/bpa-rs600.c')
| -rw-r--r-- | drivers/hwmon/pmbus/bpa-rs600.c | 208 |
1 files changed, 208 insertions, 0 deletions
diff --git a/drivers/hwmon/pmbus/bpa-rs600.c b/drivers/hwmon/pmbus/bpa-rs600.c new file mode 100644 index 000000000..f2d4e378a --- /dev/null +++ b/drivers/hwmon/pmbus/bpa-rs600.c @@ -0,0 +1,208 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Hardware monitoring driver for BluTek BPA-RS600 Power Supplies + * + * Copyright 2021 Allied Telesis Labs + */ + +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pmbus.h> +#include "pmbus.h" + +enum chips { bpa_rs600, bpd_rs600 }; + +static int bpa_rs600_read_byte_data(struct i2c_client *client, int page, int reg) +{ + int ret; + + if (page > 0) + return -ENXIO; + + switch (reg) { + case PMBUS_FAN_CONFIG_12: + /* + * Two fans are reported in PMBUS_FAN_CONFIG_12 but there is + * only one fan in the module. Mask out the FAN2 bits. + */ + ret = pmbus_read_byte_data(client, 0, PMBUS_FAN_CONFIG_12); + if (ret >= 0) + ret &= ~(PB_FAN_2_INSTALLED | PB_FAN_2_PULSE_MASK); + break; + default: + ret = -ENODATA; + break; + } + + return ret; +} + +/* + * The BPA-RS600 violates the PMBus spec. Specifically it treats the + * mantissa as unsigned. Deal with this here to allow the PMBus core + * to work with correctly encoded data. + */ +static int bpa_rs600_read_vin(struct i2c_client *client) +{ + int ret, exponent, mantissa; + + ret = pmbus_read_word_data(client, 0, 0xff, PMBUS_READ_VIN); + if (ret < 0) + return ret; + + if (ret & BIT(10)) { + exponent = ret >> 11; + mantissa = ret & 0x7ff; + + exponent++; + mantissa >>= 1; + + ret = (exponent << 11) | mantissa; + } + + return ret; +} + +/* + * Firmware V5.70 incorrectly reports 1640W for MFR_PIN_MAX. + * Deal with this by returning a sensible value. + */ +static int bpa_rs600_read_pin_max(struct i2c_client *client) +{ + int ret; + + ret = pmbus_read_word_data(client, 0, 0xff, PMBUS_MFR_PIN_MAX); + if (ret < 0) + return ret; + + /* Detect invalid 1640W (linear encoding) */ + if (ret == 0x0b34) + /* Report 700W (linear encoding) */ + return 0x095e; + + return ret; +} + +static int bpa_rs600_read_word_data(struct i2c_client *client, int page, int phase, int reg) +{ + int ret; + + if (page > 0) + return -ENXIO; + + switch (reg) { + case PMBUS_VIN_UV_WARN_LIMIT: + case PMBUS_VIN_OV_WARN_LIMIT: + case PMBUS_VOUT_UV_WARN_LIMIT: + case PMBUS_VOUT_OV_WARN_LIMIT: + case PMBUS_IIN_OC_WARN_LIMIT: + case PMBUS_IOUT_OC_WARN_LIMIT: + case PMBUS_PIN_OP_WARN_LIMIT: + case PMBUS_POUT_OP_WARN_LIMIT: + case PMBUS_VIN_UV_FAULT_LIMIT: + case PMBUS_VIN_OV_FAULT_LIMIT: + case PMBUS_VOUT_UV_FAULT_LIMIT: + case PMBUS_VOUT_OV_FAULT_LIMIT: + /* These commands return data but it is invalid/un-documented */ + ret = -ENXIO; + break; + case PMBUS_READ_VIN: + ret = bpa_rs600_read_vin(client); + break; + case PMBUS_MFR_PIN_MAX: + ret = bpa_rs600_read_pin_max(client); + break; + default: + if (reg >= PMBUS_VIRT_BASE) + ret = -ENXIO; + else + ret = -ENODATA; + break; + } + + return ret; +} + +static struct pmbus_driver_info bpa_rs600_info = { + .pages = 1, + .format[PSC_VOLTAGE_IN] = linear, + .format[PSC_VOLTAGE_OUT] = linear, + .format[PSC_CURRENT_IN] = linear, + .format[PSC_CURRENT_OUT] = linear, + .format[PSC_POWER] = linear, + .format[PSC_TEMPERATURE] = linear, + .format[PSC_FAN] = linear, + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | + PMBUS_HAVE_IIN | PMBUS_HAVE_IOUT | + PMBUS_HAVE_PIN | PMBUS_HAVE_POUT | + PMBUS_HAVE_TEMP | PMBUS_HAVE_TEMP2 | + PMBUS_HAVE_FAN12 | + PMBUS_HAVE_STATUS_VOUT | PMBUS_HAVE_STATUS_IOUT | + PMBUS_HAVE_STATUS_INPUT | PMBUS_HAVE_STATUS_TEMP | + PMBUS_HAVE_STATUS_FAN12, + .read_byte_data = bpa_rs600_read_byte_data, + .read_word_data = bpa_rs600_read_word_data, +}; + +static const struct i2c_device_id bpa_rs600_id[] = { + { "bpa-rs600", bpa_rs600 }, + { "bpd-rs600", bpd_rs600 }, + {}, +}; +MODULE_DEVICE_TABLE(i2c, bpa_rs600_id); + +static int bpa_rs600_probe(struct i2c_client *client) +{ + struct device *dev = &client->dev; + u8 buf[I2C_SMBUS_BLOCK_MAX + 1]; + int ret; + const struct i2c_device_id *mid; + + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_READ_BYTE_DATA + | I2C_FUNC_SMBUS_READ_WORD_DATA + | I2C_FUNC_SMBUS_READ_BLOCK_DATA)) + return -ENODEV; + + ret = i2c_smbus_read_block_data(client, PMBUS_MFR_MODEL, buf); + if (ret < 0) { + dev_err(dev, "Failed to read Manufacturer Model\n"); + return ret; + } + + for (mid = bpa_rs600_id; mid->name[0]; mid++) { + if (!strncasecmp(buf, mid->name, strlen(mid->name))) + break; + } + if (!mid->name[0]) { + buf[ret] = '\0'; + dev_err(dev, "Unsupported Manufacturer Model '%s'\n", buf); + return -ENODEV; + } + + return pmbus_do_probe(client, &bpa_rs600_info); +} + +static const struct of_device_id __maybe_unused bpa_rs600_of_match[] = { + { .compatible = "blutek,bpa-rs600" }, + {}, +}; +MODULE_DEVICE_TABLE(of, bpa_rs600_of_match); + +static struct i2c_driver bpa_rs600_driver = { + .driver = { + .name = "bpa-rs600", + .of_match_table = of_match_ptr(bpa_rs600_of_match), + }, + .probe_new = bpa_rs600_probe, + .id_table = bpa_rs600_id, +}; + +module_i2c_driver(bpa_rs600_driver); + +MODULE_AUTHOR("Chris Packham"); +MODULE_DESCRIPTION("PMBus driver for BluTek BPA-RS600"); +MODULE_LICENSE("GPL"); +MODULE_IMPORT_NS(PMBUS); |