diff options
Diffstat (limited to '')
-rw-r--r-- | drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 149 |
1 files changed, 77 insertions, 72 deletions
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c index aa4bf6c9a..cdc912bba 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c @@ -206,13 +206,13 @@ static s32 ixgbe_reset_cs4227(struct ixgbe_hw *hw) } if (retry == IXGBE_CS4227_RETRIES) { hw_err(hw, "CS4227 reset did not complete\n"); - return IXGBE_ERR_PHY; + return -EIO; } status = ixgbe_read_cs4227(hw, IXGBE_CS4227_EEPROM_STATUS, &value); if (status || !(value & IXGBE_CS4227_EEPROM_LOAD_OK)) { hw_err(hw, "CS4227 EEPROM did not load successfully\n"); - return IXGBE_ERR_PHY; + return -EIO; } return 0; @@ -350,13 +350,13 @@ static s32 ixgbe_identify_phy_x550em(struct ixgbe_hw *hw) static s32 ixgbe_read_phy_reg_x550em(struct ixgbe_hw *hw, u32 reg_addr, u32 device_type, u16 *phy_data) { - return IXGBE_NOT_IMPLEMENTED; + return -EOPNOTSUPP; } static s32 ixgbe_write_phy_reg_x550em(struct ixgbe_hw *hw, u32 reg_addr, u32 device_type, u16 phy_data) { - return IXGBE_NOT_IMPLEMENTED; + return -EOPNOTSUPP; } /** @@ -463,7 +463,7 @@ s32 ixgbe_fw_phy_activity(struct ixgbe_hw *hw, u16 activity, --retries; } while (retries > 0); - return IXGBE_ERR_HOST_INTERFACE_COMMAND; + return -EIO; } static const struct { @@ -511,7 +511,7 @@ static s32 ixgbe_get_phy_id_fw(struct ixgbe_hw *hw) hw->phy.id |= phy_id_lo & IXGBE_PHY_REVISION_MASK; hw->phy.revision = phy_id_lo & ~IXGBE_PHY_REVISION_MASK; if (!hw->phy.id || hw->phy.id == IXGBE_PHY_REVISION_MASK) - return IXGBE_ERR_PHY_ADDR_INVALID; + return -EFAULT; hw->phy.autoneg_advertised = hw->phy.speeds_supported; hw->phy.eee_speeds_supported = IXGBE_LINK_SPEED_100_FULL | @@ -568,7 +568,7 @@ static s32 ixgbe_setup_fw_link(struct ixgbe_hw *hw) if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { hw_err(hw, "rx_pause not valid in strict IEEE mode\n"); - return IXGBE_ERR_INVALID_LINK_SETTINGS; + return -EINVAL; } switch (hw->fc.requested_mode) { @@ -600,8 +600,10 @@ static s32 ixgbe_setup_fw_link(struct ixgbe_hw *hw) rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_SETUP_LINK, &setup); if (rc) return rc; + if (setup[0] == FW_PHY_ACT_SETUP_LINK_RSP_DOWN) - return IXGBE_ERR_OVERTEMP; + return -EIO; + return 0; } @@ -675,7 +677,7 @@ static s32 ixgbe_iosf_wait(struct ixgbe_hw *hw, u32 *ctrl) *ctrl = command; if (i == IXGBE_MDIO_COMMAND_TIMEOUT) { hw_dbg(hw, "IOSF wait timed out\n"); - return IXGBE_ERR_PHY; + return -EIO; } return 0; @@ -715,7 +717,8 @@ static s32 ixgbe_read_iosf_sb_reg_x550(struct ixgbe_hw *hw, u32 reg_addr, error = (command & IXGBE_SB_IOSF_CTRL_CMPL_ERR_MASK) >> IXGBE_SB_IOSF_CTRL_CMPL_ERR_SHIFT; hw_dbg(hw, "Failed to read, error %x\n", error); - return IXGBE_ERR_PHY; + ret = -EIO; + goto out; } if (!ret) @@ -750,9 +753,9 @@ static s32 ixgbe_get_phy_token(struct ixgbe_hw *hw) if (token_cmd.hdr.cmd_or_resp.ret_status == FW_PHY_TOKEN_OK) return 0; if (token_cmd.hdr.cmd_or_resp.ret_status != FW_PHY_TOKEN_RETRY) - return IXGBE_ERR_FW_RESP_INVALID; + return -EIO; - return IXGBE_ERR_TOKEN_RETRY; + return -EAGAIN; } /** @@ -778,7 +781,7 @@ static s32 ixgbe_put_phy_token(struct ixgbe_hw *hw) return status; if (token_cmd.hdr.cmd_or_resp.ret_status == FW_PHY_TOKEN_OK) return 0; - return IXGBE_ERR_FW_RESP_INVALID; + return -EIO; } /** @@ -942,7 +945,7 @@ static s32 ixgbe_checksum_ptr_x550(struct ixgbe_hw *hw, u16 ptr, local_buffer = buf; } else { if (buffer_size < ptr) - return IXGBE_ERR_PARAM; + return -EINVAL; local_buffer = &buffer[ptr]; } @@ -960,7 +963,7 @@ static s32 ixgbe_checksum_ptr_x550(struct ixgbe_hw *hw, u16 ptr, } if (buffer && ((u32)start + (u32)length > buffer_size)) - return IXGBE_ERR_PARAM; + return -EINVAL; for (i = start; length; i++, length--) { if (i == bufsz && !buffer) { @@ -1012,7 +1015,7 @@ static s32 ixgbe_calc_checksum_X550(struct ixgbe_hw *hw, u16 *buffer, local_buffer = eeprom_ptrs; } else { if (buffer_size < IXGBE_EEPROM_LAST_WORD) - return IXGBE_ERR_PARAM; + return -EINVAL; local_buffer = buffer; } @@ -1148,7 +1151,7 @@ static s32 ixgbe_validate_eeprom_checksum_X550(struct ixgbe_hw *hw, * calculated checksum */ if (read_checksum != checksum) { - status = IXGBE_ERR_EEPROM_CHECKSUM; + status = -EIO; hw_dbg(hw, "Invalid EEPROM checksum"); } @@ -1203,7 +1206,7 @@ static s32 ixgbe_write_ee_hostif_X550(struct ixgbe_hw *hw, u16 offset, u16 data) hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); } else { hw_dbg(hw, "write ee hostif failed to get semaphore"); - status = IXGBE_ERR_SWFW_SYNC; + status = -EBUSY; } return status; @@ -1415,7 +1418,7 @@ static s32 ixgbe_write_iosf_sb_reg_x550(struct ixgbe_hw *hw, u32 reg_addr, error = (command & IXGBE_SB_IOSF_CTRL_CMPL_ERR_MASK) >> IXGBE_SB_IOSF_CTRL_CMPL_ERR_SHIFT; hw_dbg(hw, "Failed to write, error %x\n", error); - return IXGBE_ERR_PHY; + return -EIO; } out: @@ -1558,7 +1561,7 @@ static s32 ixgbe_setup_ixfi_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed) /* iXFI is only supported with X552 */ if (mac->type != ixgbe_mac_X550EM_x) - return IXGBE_ERR_LINK_SETUP; + return -EIO; /* Disable AN and force speed to 10G Serial. */ status = ixgbe_read_iosf_sb_reg_x550(hw, @@ -1580,7 +1583,7 @@ static s32 ixgbe_setup_ixfi_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed) break; default: /* Other link speeds are not supported by internal KR PHY. */ - return IXGBE_ERR_LINK_SETUP; + return -EINVAL; } status = ixgbe_write_iosf_sb_reg_x550(hw, @@ -1611,7 +1614,7 @@ static s32 ixgbe_supported_sfp_modules_X550em(struct ixgbe_hw *hw, bool *linear) { switch (hw->phy.sfp_type) { case ixgbe_sfp_type_not_present: - return IXGBE_ERR_SFP_NOT_PRESENT; + return -ENOENT; case ixgbe_sfp_type_da_cu_core0: case ixgbe_sfp_type_da_cu_core1: *linear = true; @@ -1630,7 +1633,7 @@ static s32 ixgbe_supported_sfp_modules_X550em(struct ixgbe_hw *hw, bool *linear) case ixgbe_sfp_type_1g_cu_core0: case ixgbe_sfp_type_1g_cu_core1: default: - return IXGBE_ERR_SFP_NOT_SUPPORTED; + return -EOPNOTSUPP; } return 0; @@ -1660,7 +1663,7 @@ ixgbe_setup_mac_link_sfp_x550em(struct ixgbe_hw *hw, * there is no reason to configure CS4227 and SFP not present error is * not accepted in the setup MAC link flow. */ - if (status == IXGBE_ERR_SFP_NOT_PRESENT) + if (status == -ENOENT) return 0; if (status) @@ -1718,7 +1721,7 @@ static s32 ixgbe_setup_sfi_x550a(struct ixgbe_hw *hw, ixgbe_link_speed *speed) break; default: /* Other link speeds are not supported by internal PHY. */ - return IXGBE_ERR_LINK_SETUP; + return -EINVAL; } (void)mac->ops.write_iosf_sb_reg(hw, @@ -1803,7 +1806,7 @@ ixgbe_setup_mac_link_sfp_n(struct ixgbe_hw *hw, ixgbe_link_speed speed, /* If no SFP module present, then return success. Return success since * SFP not present error is not excepted in the setup MAC link flow. */ - if (ret_val == IXGBE_ERR_SFP_NOT_PRESENT) + if (ret_val == -ENOENT) return 0; if (ret_val) @@ -1853,7 +1856,7 @@ ixgbe_setup_mac_link_sfp_x550a(struct ixgbe_hw *hw, ixgbe_link_speed speed, /* If no SFP module present, then return success. Return success since * SFP not present error is not excepted in the setup MAC link flow. */ - if (ret_val == IXGBE_ERR_SFP_NOT_PRESENT) + if (ret_val == -ENOENT) return 0; if (ret_val) @@ -1863,7 +1866,7 @@ ixgbe_setup_mac_link_sfp_x550a(struct ixgbe_hw *hw, ixgbe_link_speed speed, ixgbe_setup_kr_speed_x550em(hw, speed); if (hw->phy.mdio.prtad == MDIO_PRTAD_NONE) - return IXGBE_ERR_PHY_ADDR_INVALID; + return -EFAULT; /* Get external PHY SKU id */ ret_val = hw->phy.ops.read_reg(hw, IXGBE_CS4227_EFUSE_PDF_SKU, @@ -1962,7 +1965,7 @@ static s32 ixgbe_check_link_t_X550em(struct ixgbe_hw *hw, u16 i, autoneg_status; if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper) - return IXGBE_ERR_CONFIG; + return -EIO; status = ixgbe_check_mac_link_generic(hw, speed, link_up, link_up_wait_to_complete); @@ -2145,9 +2148,9 @@ static s32 ixgbe_setup_sgmii_fw(struct ixgbe_hw *hw, ixgbe_link_speed speed, */ static void ixgbe_fc_autoneg_sgmii_x550em_a(struct ixgbe_hw *hw) { - s32 status = IXGBE_ERR_FC_NOT_NEGOTIATED; u32 info[FW_PHY_ACT_DATA_COUNT] = { 0 }; ixgbe_link_speed speed; + s32 status = -EIO; bool link_up; /* AN should have completed when the cable was plugged in. @@ -2165,7 +2168,7 @@ static void ixgbe_fc_autoneg_sgmii_x550em_a(struct ixgbe_hw *hw) /* Check if auto-negotiation has completed */ status = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &info); if (status || !(info[0] & FW_PHY_ACT_GET_LINK_INFO_AN_COMPLETE)) { - status = IXGBE_ERR_FC_NOT_NEGOTIATED; + status = -EIO; goto out; } @@ -2369,18 +2372,18 @@ static s32 ixgbe_get_link_capabilities_X550em(struct ixgbe_hw *hw, * @hw: pointer to hardware structure * @lsc: pointer to boolean flag which indicates whether external Base T * PHY interrupt is lsc + * @is_overtemp: indicate whether an overtemp event encountered * * Determime if external Base T PHY interrupt cause is high temperature * failure alarm or link status change. - * - * Return IXGBE_ERR_OVERTEMP if interrupt is high temperature - * failure alarm, else return PHY access status. **/ -static s32 ixgbe_get_lasi_ext_t_x550em(struct ixgbe_hw *hw, bool *lsc) +static s32 ixgbe_get_lasi_ext_t_x550em(struct ixgbe_hw *hw, bool *lsc, + bool *is_overtemp) { u32 status; u16 reg; + *is_overtemp = false; *lsc = false; /* Vendor alarm triggered */ @@ -2412,7 +2415,8 @@ static s32 ixgbe_get_lasi_ext_t_x550em(struct ixgbe_hw *hw, bool *lsc) if (reg & IXGBE_MDIO_GLOBAL_ALM_1_HI_TMP_FAIL) { /* power down the PHY in case the PHY FW didn't already */ ixgbe_set_copper_phy_power(hw, false); - return IXGBE_ERR_OVERTEMP; + *is_overtemp = true; + return -EIO; } if (reg & IXGBE_MDIO_GLOBAL_ALM_1_DEV_FAULT) { /* device fault alarm triggered */ @@ -2426,7 +2430,8 @@ static s32 ixgbe_get_lasi_ext_t_x550em(struct ixgbe_hw *hw, bool *lsc) if (reg == IXGBE_MDIO_GLOBAL_FAULT_MSG_HI_TMP) { /* power down the PHY in case the PHY FW didn't */ ixgbe_set_copper_phy_power(hw, false); - return IXGBE_ERR_OVERTEMP; + *is_overtemp = true; + return -EIO; } } @@ -2462,12 +2467,12 @@ static s32 ixgbe_get_lasi_ext_t_x550em(struct ixgbe_hw *hw, bool *lsc) **/ static s32 ixgbe_enable_lasi_ext_t_x550em(struct ixgbe_hw *hw) { + bool lsc, overtemp; u32 status; u16 reg; - bool lsc; /* Clear interrupt flags */ - status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc); + status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc, &overtemp); /* Enable link status change alarm */ @@ -2546,21 +2551,20 @@ static s32 ixgbe_enable_lasi_ext_t_x550em(struct ixgbe_hw *hw) /** * ixgbe_handle_lasi_ext_t_x550em - Handle external Base T PHY interrupt * @hw: pointer to hardware structure + * @is_overtemp: indicate whether an overtemp event encountered * * Handle external Base T PHY interrupt. If high temperature * failure alarm then return error, else if link status change * then setup internal/external PHY link - * - * Return IXGBE_ERR_OVERTEMP if interrupt is high temperature - * failure alarm, else return PHY access status. **/ -static s32 ixgbe_handle_lasi_ext_t_x550em(struct ixgbe_hw *hw) +static s32 ixgbe_handle_lasi_ext_t_x550em(struct ixgbe_hw *hw, + bool *is_overtemp) { struct ixgbe_phy_info *phy = &hw->phy; bool lsc; u32 status; - status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc); + status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc, is_overtemp); if (status) return status; @@ -2692,7 +2696,7 @@ static s32 ixgbe_setup_internal_phy_t_x550em(struct ixgbe_hw *hw) u16 speed; if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper) - return IXGBE_ERR_CONFIG; + return -EIO; if (!(hw->mac.type == ixgbe_mac_X550EM_x && !(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE))) { @@ -2735,7 +2739,7 @@ static s32 ixgbe_setup_internal_phy_t_x550em(struct ixgbe_hw *hw) break; default: /* Internal PHY does not support anything else */ - return IXGBE_ERR_INVALID_LINK_SETTINGS; + return -EINVAL; } return ixgbe_setup_ixfi_x550em(hw, &force_speed); @@ -2767,7 +2771,7 @@ static s32 ixgbe_led_on_t_x550em(struct ixgbe_hw *hw, u32 led_idx) u16 phy_data; if (led_idx >= IXGBE_X557_MAX_LED_INDEX) - return IXGBE_ERR_PARAM; + return -EINVAL; /* To turn on the LED, set mode to ON. */ hw->phy.ops.read_reg(hw, IXGBE_X557_LED_PROVISIONING + led_idx, @@ -2789,7 +2793,7 @@ static s32 ixgbe_led_off_t_x550em(struct ixgbe_hw *hw, u32 led_idx) u16 phy_data; if (led_idx >= IXGBE_X557_MAX_LED_INDEX) - return IXGBE_ERR_PARAM; + return -EINVAL; /* To turn on the LED, set mode to ON. */ hw->phy.ops.read_reg(hw, IXGBE_X557_LED_PROVISIONING + led_idx, @@ -2813,8 +2817,9 @@ static s32 ixgbe_led_off_t_x550em(struct ixgbe_hw *hw, u32 led_idx) * * Sends driver version number to firmware through the manageability * block. On success return 0 - * else returns IXGBE_ERR_SWFW_SYNC when encountering an error acquiring - * semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails. + * else returns -EBUSY when encountering an error acquiring + * semaphore, -EIO when command fails or -ENIVAL when incorrect + * params passed. **/ static s32 ixgbe_set_fw_drv_ver_x550(struct ixgbe_hw *hw, u8 maj, u8 min, u8 build, u8 sub, u16 len, @@ -2825,7 +2830,7 @@ static s32 ixgbe_set_fw_drv_ver_x550(struct ixgbe_hw *hw, u8 maj, u8 min, int i; if (!len || !driver_ver || (len > sizeof(fw_cmd.driver_string))) - return IXGBE_ERR_INVALID_ARGUMENT; + return -EINVAL; fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO; fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN + len; @@ -2850,7 +2855,7 @@ static s32 ixgbe_set_fw_drv_ver_x550(struct ixgbe_hw *hw, u8 maj, u8 min, if (fw_cmd.hdr.cmd_or_resp.ret_status != FW_CEM_RESP_STATUS_SUCCESS) - return IXGBE_ERR_HOST_INTERFACE_COMMAND; + return -EIO; return 0; } @@ -2907,7 +2912,7 @@ static s32 ixgbe_setup_fc_x550em(struct ixgbe_hw *hw) /* Validate the requested mode */ if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { hw_err(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n"); - return IXGBE_ERR_INVALID_LINK_SETTINGS; + return -EINVAL; } /* 10gig parts do not have a word in the EEPROM to determine the @@ -2942,7 +2947,7 @@ static s32 ixgbe_setup_fc_x550em(struct ixgbe_hw *hw) break; default: hw_err(hw, "Flow control param set incorrectly\n"); - return IXGBE_ERR_CONFIG; + return -EIO; } switch (hw->device_id) { @@ -2986,8 +2991,8 @@ static s32 ixgbe_setup_fc_x550em(struct ixgbe_hw *hw) static void ixgbe_fc_autoneg_backplane_x550em_a(struct ixgbe_hw *hw) { u32 link_s1, lp_an_page_low, an_cntl_1; - s32 status = IXGBE_ERR_FC_NOT_NEGOTIATED; ixgbe_link_speed speed; + s32 status = -EIO; bool link_up; /* AN should have completed when the cable was plugged in. @@ -3013,7 +3018,7 @@ static void ixgbe_fc_autoneg_backplane_x550em_a(struct ixgbe_hw *hw) if (status || (link_s1 & IXGBE_KRM_LINK_S1_MAC_AN_COMPLETE) == 0) { hw_dbg(hw, "Auto-Negotiation did not complete\n"); - status = IXGBE_ERR_FC_NOT_NEGOTIATED; + status = -EIO; goto out; } @@ -3187,21 +3192,23 @@ static s32 ixgbe_reset_phy_fw(struct ixgbe_hw *hw) /** * ixgbe_check_overtemp_fw - Check firmware-controlled PHYs for overtemp * @hw: pointer to hardware structure + * + * Return true when an overtemp event detected, otherwise false. */ -static s32 ixgbe_check_overtemp_fw(struct ixgbe_hw *hw) +static bool ixgbe_check_overtemp_fw(struct ixgbe_hw *hw) { u32 store[FW_PHY_ACT_DATA_COUNT] = { 0 }; s32 rc; rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &store); if (rc) - return rc; + return false; if (store[0] & FW_PHY_ACT_GET_LINK_INFO_TEMP) { ixgbe_shutdown_fw_phy(hw); - return IXGBE_ERR_OVERTEMP; + return true; } - return 0; + return false; } /** @@ -3251,8 +3258,7 @@ static s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw) /* Identify the PHY or SFP module */ ret_val = phy->ops.identify(hw); - if (ret_val == IXGBE_ERR_SFP_NOT_SUPPORTED || - ret_val == IXGBE_ERR_PHY_ADDR_INVALID) + if (ret_val == -EOPNOTSUPP || ret_val == -EFAULT) return ret_val; /* Setup function pointers based on detected hardware */ @@ -3460,8 +3466,7 @@ static s32 ixgbe_reset_hw_X550em(struct ixgbe_hw *hw) /* PHY ops must be identified and initialized prior to reset */ status = hw->phy.ops.init(hw); - if (status == IXGBE_ERR_SFP_NOT_SUPPORTED || - status == IXGBE_ERR_PHY_ADDR_INVALID) + if (status == -EOPNOTSUPP || status == -EFAULT) return status; /* start the external PHY */ @@ -3477,7 +3482,7 @@ static s32 ixgbe_reset_hw_X550em(struct ixgbe_hw *hw) hw->phy.sfp_setup_needed = false; } - if (status == IXGBE_ERR_SFP_NOT_SUPPORTED) + if (status == -EOPNOTSUPP) return status; /* Reset PHY */ @@ -3501,7 +3506,7 @@ mac_reset_top: status = hw->mac.ops.acquire_swfw_sync(hw, swfw_mask); if (status) { hw_dbg(hw, "semaphore failed with %d", status); - return IXGBE_ERR_SWFW_SYNC; + return -EBUSY; } ctrl |= IXGBE_READ_REG(hw, IXGBE_CTRL); @@ -3519,7 +3524,7 @@ mac_reset_top: } if (ctrl & IXGBE_CTRL_RST_MASK) { - status = IXGBE_ERR_RESET_FAILED; + status = -EIO; hw_dbg(hw, "Reset polling failed to complete.\n"); } @@ -3615,7 +3620,7 @@ static s32 ixgbe_setup_fc_backplane_x550em_a(struct ixgbe_hw *hw) /* Validate the requested mode */ if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { hw_err(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n"); - return IXGBE_ERR_INVALID_LINK_SETTINGS; + return -EINVAL; } if (hw->fc.requested_mode == ixgbe_fc_default) @@ -3672,7 +3677,7 @@ static s32 ixgbe_setup_fc_backplane_x550em_a(struct ixgbe_hw *hw) break; default: hw_err(hw, "Flow control param set incorrectly\n"); - return IXGBE_ERR_CONFIG; + return -EIO; } status = hw->mac.ops.write_iosf_sb_reg(hw, @@ -3768,7 +3773,7 @@ static s32 ixgbe_acquire_swfw_sync_x550em_a(struct ixgbe_hw *hw, u32 mask) return 0; if (hmask) ixgbe_release_swfw_sync_X540(hw, hmask); - if (status != IXGBE_ERR_TOKEN_RETRY) + if (status != -EAGAIN) return status; msleep(FW_PHY_TOKEN_DELAY); } @@ -3812,7 +3817,7 @@ static s32 ixgbe_read_phy_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr, s32 status; if (hw->mac.ops.acquire_swfw_sync(hw, mask)) - return IXGBE_ERR_SWFW_SYNC; + return -EBUSY; status = hw->phy.ops.read_reg_mdi(hw, reg_addr, device_type, phy_data); @@ -3838,7 +3843,7 @@ static s32 ixgbe_write_phy_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr, s32 status; if (hw->mac.ops.acquire_swfw_sync(hw, mask)) - return IXGBE_ERR_SWFW_SYNC; + return -EBUSY; status = ixgbe_write_phy_reg_mdi(hw, reg_addr, device_type, phy_data); hw->mac.ops.release_swfw_sync(hw, mask); |