diff options
Diffstat (limited to 'drivers/phy/qualcomm/phy-qcom-ipq806x-usb.c')
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-ipq806x-usb.c | 566 |
1 files changed, 566 insertions, 0 deletions
diff --git a/drivers/phy/qualcomm/phy-qcom-ipq806x-usb.c b/drivers/phy/qualcomm/phy-qcom-ipq806x-usb.c new file mode 100644 index 000000000..7bacc527f --- /dev/null +++ b/drivers/phy/qualcomm/phy-qcom-ipq806x-usb.c @@ -0,0 +1,566 @@ +// SPDX-License-Identifier: GPL-2.0-only + +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/phy/phy.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/regmap.h> +#include <linux/mfd/syscon.h> +#include <linux/bitfield.h> + +/* USB QSCRATCH Hardware registers */ +#define QSCRATCH_GENERAL_CFG (0x08) +#define HSUSB_PHY_CTRL_REG (0x10) + +/* PHY_CTRL_REG */ +#define HSUSB_CTRL_DMSEHV_CLAMP BIT(24) +#define HSUSB_CTRL_USB2_SUSPEND BIT(23) +#define HSUSB_CTRL_UTMI_CLK_EN BIT(21) +#define HSUSB_CTRL_UTMI_OTG_VBUS_VALID BIT(20) +#define HSUSB_CTRL_USE_CLKCORE BIT(18) +#define HSUSB_CTRL_DPSEHV_CLAMP BIT(17) +#define HSUSB_CTRL_COMMONONN BIT(11) +#define HSUSB_CTRL_ID_HV_CLAMP BIT(9) +#define HSUSB_CTRL_OTGSESSVLD_CLAMP BIT(8) +#define HSUSB_CTRL_CLAMP_EN BIT(7) +#define HSUSB_CTRL_RETENABLEN BIT(1) +#define HSUSB_CTRL_POR BIT(0) + +/* QSCRATCH_GENERAL_CFG */ +#define HSUSB_GCFG_XHCI_REV BIT(2) + +/* USB QSCRATCH Hardware registers */ +#define SSUSB_PHY_CTRL_REG (0x00) +#define SSUSB_PHY_PARAM_CTRL_1 (0x04) +#define SSUSB_PHY_PARAM_CTRL_2 (0x08) +#define CR_PROTOCOL_DATA_IN_REG (0x0c) +#define CR_PROTOCOL_DATA_OUT_REG (0x10) +#define CR_PROTOCOL_CAP_ADDR_REG (0x14) +#define CR_PROTOCOL_CAP_DATA_REG (0x18) +#define CR_PROTOCOL_READ_REG (0x1c) +#define CR_PROTOCOL_WRITE_REG (0x20) + +/* PHY_CTRL_REG */ +#define SSUSB_CTRL_REF_USE_PAD BIT(28) +#define SSUSB_CTRL_TEST_POWERDOWN BIT(27) +#define SSUSB_CTRL_LANE0_PWR_PRESENT BIT(24) +#define SSUSB_CTRL_SS_PHY_EN BIT(8) +#define SSUSB_CTRL_SS_PHY_RESET BIT(7) + +/* SSPHY control registers - Does this need 0x30? */ +#define SSPHY_CTRL_RX_OVRD_IN_HI(lane) (0x1006 + 0x100 * (lane)) +#define SSPHY_CTRL_TX_OVRD_DRV_LO(lane) (0x1002 + 0x100 * (lane)) + +/* SSPHY SoC version specific values */ +#define SSPHY_RX_EQ_VALUE 4 /* Override value for rx_eq */ +/* Override value for transmit preemphasis */ +#define SSPHY_TX_DEEMPH_3_5DB 23 +/* Override value for mpll */ +#define SSPHY_MPLL_VALUE 0 + +/* QSCRATCH PHY_PARAM_CTRL1 fields */ +#define PHY_PARAM_CTRL1_TX_FULL_SWING_MASK GENMASK(26, 19) +#define PHY_PARAM_CTRL1_TX_DEEMPH_6DB_MASK GENMASK(19, 13) +#define PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB_MASK GENMASK(13, 7) +#define PHY_PARAM_CTRL1_LOS_BIAS_MASK GENMASK(7, 2) + +#define PHY_PARAM_CTRL1_MASK \ + (PHY_PARAM_CTRL1_TX_FULL_SWING_MASK | \ + PHY_PARAM_CTRL1_TX_DEEMPH_6DB_MASK | \ + PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB_MASK | \ + PHY_PARAM_CTRL1_LOS_BIAS_MASK) + +#define PHY_PARAM_CTRL1_TX_FULL_SWING(x) \ + FIELD_PREP(PHY_PARAM_CTRL1_TX_FULL_SWING_MASK, (x)) +#define PHY_PARAM_CTRL1_TX_DEEMPH_6DB(x) \ + FIELD_PREP(PHY_PARAM_CTRL1_TX_DEEMPH_6DB_MASK, (x)) +#define PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB(x) \ + FIELD_PREP(PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB_MASK, x) +#define PHY_PARAM_CTRL1_LOS_BIAS(x) \ + FIELD_PREP(PHY_PARAM_CTRL1_LOS_BIAS_MASK, (x)) + +/* RX OVRD IN HI bits */ +#define RX_OVRD_IN_HI_RX_RESET_OVRD BIT(13) +#define RX_OVRD_IN_HI_RX_RX_RESET BIT(12) +#define RX_OVRD_IN_HI_RX_EQ_OVRD BIT(11) +#define RX_OVRD_IN_HI_RX_EQ_MASK GENMASK(10, 7) +#define RX_OVRD_IN_HI_RX_EQ(x) FIELD_PREP(RX_OVRD_IN_HI_RX_EQ_MASK, (x)) +#define RX_OVRD_IN_HI_RX_EQ_EN_OVRD BIT(7) +#define RX_OVRD_IN_HI_RX_EQ_EN BIT(6) +#define RX_OVRD_IN_HI_RX_LOS_FILTER_OVRD BIT(5) +#define RX_OVRD_IN_HI_RX_LOS_FILTER_MASK GENMASK(4, 2) +#define RX_OVRD_IN_HI_RX_RATE_OVRD BIT(2) +#define RX_OVRD_IN_HI_RX_RATE_MASK GENMASK(2, 0) + +/* TX OVRD DRV LO register bits */ +#define TX_OVRD_DRV_LO_AMPLITUDE_MASK GENMASK(6, 0) +#define TX_OVRD_DRV_LO_PREEMPH_MASK GENMASK(13, 6) +#define TX_OVRD_DRV_LO_PREEMPH(x) ((x) << 7) +#define TX_OVRD_DRV_LO_EN BIT(14) + +/* MPLL bits */ +#define SSPHY_MPLL_MASK GENMASK(8, 5) +#define SSPHY_MPLL(x) ((x) << 5) + +/* SS CAP register bits */ +#define SS_CR_CAP_ADDR_REG BIT(0) +#define SS_CR_CAP_DATA_REG BIT(0) +#define SS_CR_READ_REG BIT(0) +#define SS_CR_WRITE_REG BIT(0) + +#define LATCH_SLEEP 40 +#define LATCH_TIMEOUT 100 + +struct usb_phy { + void __iomem *base; + struct device *dev; + struct clk *xo_clk; + struct clk *ref_clk; + u32 rx_eq; + u32 tx_deamp_3_5db; + u32 mpll; +}; + +struct phy_drvdata { + struct phy_ops ops; + u32 clk_rate; +}; + +/** + * usb_phy_write_readback() - Write register and read back masked value to + * confirm it is written + * + * @phy_dwc3: QCOM DWC3 phy context + * @offset: register offset. + * @mask: register bitmask specifying what should be updated + * @val: value to write. + */ +static inline void usb_phy_write_readback(struct usb_phy *phy_dwc3, + u32 offset, + const u32 mask, u32 val) +{ + u32 write_val, tmp = readl(phy_dwc3->base + offset); + + tmp &= ~mask; /* retain other bits */ + write_val = tmp | val; + + writel(write_val, phy_dwc3->base + offset); + + /* Read back to see if val was written */ + tmp = readl(phy_dwc3->base + offset); + tmp &= mask; /* clear other bits */ + + if (tmp != val) + dev_err(phy_dwc3->dev, "write: %x to QSCRATCH: %x FAILED\n", val, offset); +} + +static int wait_for_latch(void __iomem *addr) +{ + u32 val; + + return readl_poll_timeout(addr, val, !val, LATCH_SLEEP, LATCH_TIMEOUT); +} + +/** + * usb_ss_write_phycreg() - Write SSPHY register + * + * @phy_dwc3: QCOM DWC3 phy context + * @addr: SSPHY address to write. + * @val: value to write. + */ +static int usb_ss_write_phycreg(struct usb_phy *phy_dwc3, + u32 addr, u32 val) +{ + int ret; + + writel(addr, phy_dwc3->base + CR_PROTOCOL_DATA_IN_REG); + writel(SS_CR_CAP_ADDR_REG, + phy_dwc3->base + CR_PROTOCOL_CAP_ADDR_REG); + + ret = wait_for_latch(phy_dwc3->base + CR_PROTOCOL_CAP_ADDR_REG); + if (ret) + goto err_wait; + + writel(val, phy_dwc3->base + CR_PROTOCOL_DATA_IN_REG); + writel(SS_CR_CAP_DATA_REG, + phy_dwc3->base + CR_PROTOCOL_CAP_DATA_REG); + + ret = wait_for_latch(phy_dwc3->base + CR_PROTOCOL_CAP_DATA_REG); + if (ret) + goto err_wait; + + writel(SS_CR_WRITE_REG, phy_dwc3->base + CR_PROTOCOL_WRITE_REG); + + ret = wait_for_latch(phy_dwc3->base + CR_PROTOCOL_WRITE_REG); + +err_wait: + if (ret) + dev_err(phy_dwc3->dev, "timeout waiting for latch\n"); + return ret; +} + +/** + * usb_ss_read_phycreg() - Read SSPHY register. + * + * @phy_dwc3: QCOM DWC3 phy context + * @addr: SSPHY address to read. + * @val: pointer in which read is store. + */ +static int usb_ss_read_phycreg(struct usb_phy *phy_dwc3, + u32 addr, u32 *val) +{ + int ret; + + writel(addr, phy_dwc3->base + CR_PROTOCOL_DATA_IN_REG); + writel(SS_CR_CAP_ADDR_REG, + phy_dwc3->base + CR_PROTOCOL_CAP_ADDR_REG); + + ret = wait_for_latch(phy_dwc3->base + CR_PROTOCOL_CAP_ADDR_REG); + if (ret) + goto err_wait; + + /* + * Due to hardware bug, first read of SSPHY register might be + * incorrect. Hence as workaround, SW should perform SSPHY register + * read twice, but use only second read and ignore first read. + */ + writel(SS_CR_READ_REG, phy_dwc3->base + CR_PROTOCOL_READ_REG); + + ret = wait_for_latch(phy_dwc3->base + CR_PROTOCOL_READ_REG); + if (ret) + goto err_wait; + + /* throwaway read */ + readl(phy_dwc3->base + CR_PROTOCOL_DATA_OUT_REG); + + writel(SS_CR_READ_REG, phy_dwc3->base + CR_PROTOCOL_READ_REG); + + ret = wait_for_latch(phy_dwc3->base + CR_PROTOCOL_READ_REG); + if (ret) + goto err_wait; + + *val = readl(phy_dwc3->base + CR_PROTOCOL_DATA_OUT_REG); + +err_wait: + return ret; +} + +static int qcom_ipq806x_usb_hs_phy_init(struct phy *phy) +{ + struct usb_phy *phy_dwc3 = phy_get_drvdata(phy); + int ret; + u32 val; + + ret = clk_prepare_enable(phy_dwc3->xo_clk); + if (ret) + return ret; + + ret = clk_prepare_enable(phy_dwc3->ref_clk); + if (ret) { + clk_disable_unprepare(phy_dwc3->xo_clk); + return ret; + } + + /* + * HSPHY Initialization: Enable UTMI clock, select 19.2MHz fsel + * enable clamping, and disable RETENTION (power-on default is ENABLED) + */ + val = HSUSB_CTRL_DPSEHV_CLAMP | HSUSB_CTRL_DMSEHV_CLAMP | + HSUSB_CTRL_RETENABLEN | HSUSB_CTRL_COMMONONN | + HSUSB_CTRL_OTGSESSVLD_CLAMP | HSUSB_CTRL_ID_HV_CLAMP | + HSUSB_CTRL_UTMI_OTG_VBUS_VALID | HSUSB_CTRL_UTMI_CLK_EN | + HSUSB_CTRL_CLAMP_EN | 0x70; + + /* use core clock if external reference is not present */ + if (!phy_dwc3->xo_clk) + val |= HSUSB_CTRL_USE_CLKCORE; + + writel(val, phy_dwc3->base + HSUSB_PHY_CTRL_REG); + usleep_range(2000, 2200); + + /* Disable (bypass) VBUS and ID filters */ + writel(HSUSB_GCFG_XHCI_REV, phy_dwc3->base + QSCRATCH_GENERAL_CFG); + + return 0; +} + +static int qcom_ipq806x_usb_hs_phy_exit(struct phy *phy) +{ + struct usb_phy *phy_dwc3 = phy_get_drvdata(phy); + + clk_disable_unprepare(phy_dwc3->ref_clk); + clk_disable_unprepare(phy_dwc3->xo_clk); + + return 0; +} + +static int qcom_ipq806x_usb_ss_phy_init(struct phy *phy) +{ + struct usb_phy *phy_dwc3 = phy_get_drvdata(phy); + int ret; + u32 data; + + ret = clk_prepare_enable(phy_dwc3->xo_clk); + if (ret) + return ret; + + ret = clk_prepare_enable(phy_dwc3->ref_clk); + if (ret) { + clk_disable_unprepare(phy_dwc3->xo_clk); + return ret; + } + + /* reset phy */ + data = readl(phy_dwc3->base + SSUSB_PHY_CTRL_REG); + writel(data | SSUSB_CTRL_SS_PHY_RESET, + phy_dwc3->base + SSUSB_PHY_CTRL_REG); + usleep_range(2000, 2200); + writel(data, phy_dwc3->base + SSUSB_PHY_CTRL_REG); + + /* clear REF_PAD if we don't have XO clk */ + if (!phy_dwc3->xo_clk) + data &= ~SSUSB_CTRL_REF_USE_PAD; + else + data |= SSUSB_CTRL_REF_USE_PAD; + + writel(data, phy_dwc3->base + SSUSB_PHY_CTRL_REG); + + /* wait for ref clk to become stable, this can take up to 30ms */ + msleep(30); + + data |= SSUSB_CTRL_SS_PHY_EN | SSUSB_CTRL_LANE0_PWR_PRESENT; + writel(data, phy_dwc3->base + SSUSB_PHY_CTRL_REG); + + /* + * WORKAROUND: There is SSPHY suspend bug due to which USB enumerates + * in HS mode instead of SS mode. Workaround it by asserting + * LANE0.TX_ALT_BLOCK.EN_ALT_BUS to enable TX to use alt bus mode + */ + ret = usb_ss_read_phycreg(phy_dwc3, 0x102D, &data); + if (ret) + goto err_phy_trans; + + data |= (1 << 7); + ret = usb_ss_write_phycreg(phy_dwc3, 0x102D, data); + if (ret) + goto err_phy_trans; + + ret = usb_ss_read_phycreg(phy_dwc3, 0x1010, &data); + if (ret) + goto err_phy_trans; + + data &= ~0xff0; + data |= 0x20; + ret = usb_ss_write_phycreg(phy_dwc3, 0x1010, data); + if (ret) + goto err_phy_trans; + + /* + * Fix RX Equalization setting as follows + * LANE0.RX_OVRD_IN_HI. RX_EQ_EN set to 0 + * LANE0.RX_OVRD_IN_HI.RX_EQ_EN_OVRD set to 1 + * LANE0.RX_OVRD_IN_HI.RX_EQ set based on SoC version + * LANE0.RX_OVRD_IN_HI.RX_EQ_OVRD set to 1 + */ + ret = usb_ss_read_phycreg(phy_dwc3, SSPHY_CTRL_RX_OVRD_IN_HI(0), &data); + if (ret) + goto err_phy_trans; + + data &= ~RX_OVRD_IN_HI_RX_EQ_EN; + data |= RX_OVRD_IN_HI_RX_EQ_EN_OVRD; + data &= ~RX_OVRD_IN_HI_RX_EQ_MASK; + data |= RX_OVRD_IN_HI_RX_EQ(phy_dwc3->rx_eq); + data |= RX_OVRD_IN_HI_RX_EQ_OVRD; + ret = usb_ss_write_phycreg(phy_dwc3, + SSPHY_CTRL_RX_OVRD_IN_HI(0), data); + if (ret) + goto err_phy_trans; + + /* + * Set EQ and TX launch amplitudes as follows + * LANE0.TX_OVRD_DRV_LO.PREEMPH set based on SoC version + * LANE0.TX_OVRD_DRV_LO.AMPLITUDE set to 110 + * LANE0.TX_OVRD_DRV_LO.EN set to 1. + */ + ret = usb_ss_read_phycreg(phy_dwc3, + SSPHY_CTRL_TX_OVRD_DRV_LO(0), &data); + if (ret) + goto err_phy_trans; + + data &= ~TX_OVRD_DRV_LO_PREEMPH_MASK; + data |= TX_OVRD_DRV_LO_PREEMPH(phy_dwc3->tx_deamp_3_5db); + data &= ~TX_OVRD_DRV_LO_AMPLITUDE_MASK; + data |= 0x6E; + data |= TX_OVRD_DRV_LO_EN; + ret = usb_ss_write_phycreg(phy_dwc3, + SSPHY_CTRL_TX_OVRD_DRV_LO(0), data); + if (ret) + goto err_phy_trans; + + data = 0; + data &= ~SSPHY_MPLL_MASK; + data |= SSPHY_MPLL(phy_dwc3->mpll); + usb_ss_write_phycreg(phy_dwc3, 0x30, data); + + /* + * Set the QSCRATCH PHY_PARAM_CTRL1 parameters as follows + * TX_FULL_SWING [26:20] amplitude to 110 + * TX_DEEMPH_6DB [19:14] to 32 + * TX_DEEMPH_3_5DB [13:8] set based on SoC version + * LOS_BIAS [7:3] to 9 + */ + data = readl(phy_dwc3->base + SSUSB_PHY_PARAM_CTRL_1); + + data &= ~PHY_PARAM_CTRL1_MASK; + + data |= PHY_PARAM_CTRL1_TX_FULL_SWING(0x6e) | + PHY_PARAM_CTRL1_TX_DEEMPH_6DB(0x20) | + PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB(phy_dwc3->tx_deamp_3_5db) | + PHY_PARAM_CTRL1_LOS_BIAS(0x9); + + usb_phy_write_readback(phy_dwc3, SSUSB_PHY_PARAM_CTRL_1, + PHY_PARAM_CTRL1_MASK, data); + +err_phy_trans: + return ret; +} + +static int qcom_ipq806x_usb_ss_phy_exit(struct phy *phy) +{ + struct usb_phy *phy_dwc3 = phy_get_drvdata(phy); + + /* Sequence to put SSPHY in low power state: + * 1. Clear REF_PHY_EN in PHY_CTRL_REG + * 2. Clear REF_USE_PAD in PHY_CTRL_REG + * 3. Set TEST_POWERED_DOWN in PHY_CTRL_REG to enable PHY retention + */ + usb_phy_write_readback(phy_dwc3, SSUSB_PHY_CTRL_REG, + SSUSB_CTRL_SS_PHY_EN, 0x0); + usb_phy_write_readback(phy_dwc3, SSUSB_PHY_CTRL_REG, + SSUSB_CTRL_REF_USE_PAD, 0x0); + usb_phy_write_readback(phy_dwc3, SSUSB_PHY_CTRL_REG, + SSUSB_CTRL_TEST_POWERDOWN, 0x0); + + clk_disable_unprepare(phy_dwc3->ref_clk); + clk_disable_unprepare(phy_dwc3->xo_clk); + + return 0; +} + +static const struct phy_drvdata qcom_ipq806x_usb_hs_drvdata = { + .ops = { + .init = qcom_ipq806x_usb_hs_phy_init, + .exit = qcom_ipq806x_usb_hs_phy_exit, + .owner = THIS_MODULE, + }, + .clk_rate = 60000000, +}; + +static const struct phy_drvdata qcom_ipq806x_usb_ss_drvdata = { + .ops = { + .init = qcom_ipq806x_usb_ss_phy_init, + .exit = qcom_ipq806x_usb_ss_phy_exit, + .owner = THIS_MODULE, + }, + .clk_rate = 125000000, +}; + +static const struct of_device_id qcom_ipq806x_usb_phy_table[] = { + { .compatible = "qcom,ipq806x-usb-phy-hs", + .data = &qcom_ipq806x_usb_hs_drvdata }, + { .compatible = "qcom,ipq806x-usb-phy-ss", + .data = &qcom_ipq806x_usb_ss_drvdata }, + { /* Sentinel */ } +}; +MODULE_DEVICE_TABLE(of, qcom_ipq806x_usb_phy_table); + +static int qcom_ipq806x_usb_phy_probe(struct platform_device *pdev) +{ + struct resource *res; + resource_size_t size; + struct phy *generic_phy; + struct usb_phy *phy_dwc3; + const struct phy_drvdata *data; + struct phy_provider *phy_provider; + + phy_dwc3 = devm_kzalloc(&pdev->dev, sizeof(*phy_dwc3), GFP_KERNEL); + if (!phy_dwc3) + return -ENOMEM; + + data = of_device_get_match_data(&pdev->dev); + + phy_dwc3->dev = &pdev->dev; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) + return -EINVAL; + size = resource_size(res); + phy_dwc3->base = devm_ioremap(phy_dwc3->dev, res->start, size); + + if (!phy_dwc3->base) { + dev_err(phy_dwc3->dev, "failed to map reg\n"); + return -ENOMEM; + } + + phy_dwc3->ref_clk = devm_clk_get(phy_dwc3->dev, "ref"); + if (IS_ERR(phy_dwc3->ref_clk)) { + dev_dbg(phy_dwc3->dev, "cannot get reference clock\n"); + return PTR_ERR(phy_dwc3->ref_clk); + } + + clk_set_rate(phy_dwc3->ref_clk, data->clk_rate); + + phy_dwc3->xo_clk = devm_clk_get(phy_dwc3->dev, "xo"); + if (IS_ERR(phy_dwc3->xo_clk)) { + dev_dbg(phy_dwc3->dev, "cannot get TCXO clock\n"); + phy_dwc3->xo_clk = NULL; + } + + /* Parse device node to probe HSIO settings */ + if (device_property_read_u32(&pdev->dev, "qcom,rx-eq", + &phy_dwc3->rx_eq)) + phy_dwc3->rx_eq = SSPHY_RX_EQ_VALUE; + + if (device_property_read_u32(&pdev->dev, "qcom,tx-deamp_3_5db", + &phy_dwc3->tx_deamp_3_5db)) + phy_dwc3->tx_deamp_3_5db = SSPHY_TX_DEEMPH_3_5DB; + + if (device_property_read_u32(&pdev->dev, "qcom,mpll", &phy_dwc3->mpll)) + phy_dwc3->mpll = SSPHY_MPLL_VALUE; + + generic_phy = devm_phy_create(phy_dwc3->dev, pdev->dev.of_node, &data->ops); + + if (IS_ERR(generic_phy)) + return PTR_ERR(generic_phy); + + phy_set_drvdata(generic_phy, phy_dwc3); + platform_set_drvdata(pdev, phy_dwc3); + + phy_provider = devm_of_phy_provider_register(phy_dwc3->dev, + of_phy_simple_xlate); + + if (IS_ERR(phy_provider)) + return PTR_ERR(phy_provider); + + return 0; +} + +static struct platform_driver qcom_ipq806x_usb_phy_driver = { + .probe = qcom_ipq806x_usb_phy_probe, + .driver = { + .name = "qcom-ipq806x-usb-phy", + .of_match_table = qcom_ipq806x_usb_phy_table, + }, +}; + +module_platform_driver(qcom_ipq806x_usb_phy_driver); + +MODULE_ALIAS("platform:phy-qcom-ipq806x-usb"); +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Andy Gross <agross@codeaurora.org>"); +MODULE_AUTHOR("Ivan T. Ivanov <iivanov@mm-sol.com>"); +MODULE_DESCRIPTION("DesignWare USB3 QCOM PHY driver"); |