diff options
Diffstat (limited to 'net/ipv4/Kconfig')
| -rw-r--r-- | net/ipv4/Kconfig | 753 |
1 files changed, 753 insertions, 0 deletions
diff --git a/net/ipv4/Kconfig b/net/ipv4/Kconfig new file mode 100644 index 000000000..2dfb12230 --- /dev/null +++ b/net/ipv4/Kconfig @@ -0,0 +1,753 @@ +# SPDX-License-Identifier: GPL-2.0-only +# +# IP configuration +# +config IP_MULTICAST + bool "IP: multicasting" + help + This is code for addressing several networked computers at once, + enlarging your kernel by about 2 KB. You need multicasting if you + intend to participate in the MBONE, a high bandwidth network on top + of the Internet which carries audio and video broadcasts. More + information about the MBONE is on the WWW at + <https://www.savetz.com/mbone/>. For most people, it's safe to say N. + +config IP_ADVANCED_ROUTER + bool "IP: advanced router" + help + If you intend to run your Linux box mostly as a router, i.e. as a + computer that forwards and redistributes network packets, say Y; you + will then be presented with several options that allow more precise + control about the routing process. + + The answer to this question won't directly affect the kernel: + answering N will just cause the configurator to skip all the + questions about advanced routing. + + Note that your box can only act as a router if you enable IP + forwarding in your kernel; you can do that by saying Y to "/proc + file system support" and "Sysctl support" below and executing the + line + + echo "1" > /proc/sys/net/ipv4/ip_forward + + at boot time after the /proc file system has been mounted. + + If you turn on IP forwarding, you should consider the rp_filter, which + automatically rejects incoming packets if the routing table entry + for their source address doesn't match the network interface they're + arriving on. This has security advantages because it prevents the + so-called IP spoofing, however it can pose problems if you use + asymmetric routing (packets from you to a host take a different path + than packets from that host to you) or if you operate a non-routing + host which has several IP addresses on different interfaces. To turn + rp_filter on use: + + echo 1 > /proc/sys/net/ipv4/conf/<device>/rp_filter + or + echo 1 > /proc/sys/net/ipv4/conf/all/rp_filter + + Note that some distributions enable it in startup scripts. + For details about rp_filter strict and loose mode read + <file:Documentation/networking/ip-sysctl.rst>. + + If unsure, say N here. + +config IP_FIB_TRIE_STATS + bool "FIB TRIE statistics" + depends on IP_ADVANCED_ROUTER + help + Keep track of statistics on structure of FIB TRIE table. + Useful for testing and measuring TRIE performance. + +config IP_MULTIPLE_TABLES + bool "IP: policy routing" + depends on IP_ADVANCED_ROUTER + select FIB_RULES + help + Normally, a router decides what to do with a received packet based + solely on the packet's final destination address. If you say Y here, + the Linux router will also be able to take the packet's source + address into account. Furthermore, the TOS (Type-Of-Service) field + of the packet can be used for routing decisions as well. + + If you need more information, see the Linux Advanced + Routing and Traffic Control documentation at + <https://lartc.org/howto/lartc.rpdb.html> + + If unsure, say N. + +config IP_ROUTE_MULTIPATH + bool "IP: equal cost multipath" + depends on IP_ADVANCED_ROUTER + help + Normally, the routing tables specify a single action to be taken in + a deterministic manner for a given packet. If you say Y here + however, it becomes possible to attach several actions to a packet + pattern, in effect specifying several alternative paths to travel + for those packets. The router considers all these paths to be of + equal "cost" and chooses one of them in a non-deterministic fashion + if a matching packet arrives. + +config IP_ROUTE_VERBOSE + bool "IP: verbose route monitoring" + depends on IP_ADVANCED_ROUTER + help + If you say Y here, which is recommended, then the kernel will print + verbose messages regarding the routing, for example warnings about + received packets which look strange and could be evidence of an + attack or a misconfigured system somewhere. The information is + handled by the klogd daemon which is responsible for kernel messages + ("man klogd"). + +config IP_ROUTE_CLASSID + bool + +config IP_PNP + bool "IP: kernel level autoconfiguration" + help + This enables automatic configuration of IP addresses of devices and + of the routing table during kernel boot, based on either information + supplied on the kernel command line or by BOOTP or RARP protocols. + You need to say Y only for diskless machines requiring network + access to boot (in which case you want to say Y to "Root file system + on NFS" as well), because all other machines configure the network + in their startup scripts. + +config IP_PNP_DHCP + bool "IP: DHCP support" + depends on IP_PNP + help + If you want your Linux box to mount its whole root file system (the + one containing the directory /) from some other computer over the + net via NFS and you want the IP address of your computer to be + discovered automatically at boot time using the DHCP protocol (a + special protocol designed for doing this job), say Y here. In case + the boot ROM of your network card was designed for booting Linux and + does DHCP itself, providing all necessary information on the kernel + command line, you can say N here. + + If unsure, say Y. Note that if you want to use DHCP, a DHCP server + must be operating on your network. Read + <file:Documentation/admin-guide/nfs/nfsroot.rst> for details. + +config IP_PNP_BOOTP + bool "IP: BOOTP support" + depends on IP_PNP + help + If you want your Linux box to mount its whole root file system (the + one containing the directory /) from some other computer over the + net via NFS and you want the IP address of your computer to be + discovered automatically at boot time using the BOOTP protocol (a + special protocol designed for doing this job), say Y here. In case + the boot ROM of your network card was designed for booting Linux and + does BOOTP itself, providing all necessary information on the kernel + command line, you can say N here. If unsure, say Y. Note that if you + want to use BOOTP, a BOOTP server must be operating on your network. + Read <file:Documentation/admin-guide/nfs/nfsroot.rst> for details. + +config IP_PNP_RARP + bool "IP: RARP support" + depends on IP_PNP + help + If you want your Linux box to mount its whole root file system (the + one containing the directory /) from some other computer over the + net via NFS and you want the IP address of your computer to be + discovered automatically at boot time using the RARP protocol (an + older protocol which is being obsoleted by BOOTP and DHCP), say Y + here. Note that if you want to use RARP, a RARP server must be + operating on your network. Read + <file:Documentation/admin-guide/nfs/nfsroot.rst> for details. + +config NET_IPIP + tristate "IP: tunneling" + select INET_TUNNEL + select NET_IP_TUNNEL + help + Tunneling means encapsulating data of one protocol type within + another protocol and sending it over a channel that understands the + encapsulating protocol. This particular tunneling driver implements + encapsulation of IP within IP, which sounds kind of pointless, but + can be useful if you want to make your (or some other) machine + appear on a different network than it physically is, or to use + mobile-IP facilities (allowing laptops to seamlessly move between + networks without changing their IP addresses). + + Saying Y to this option will produce two modules ( = code which can + be inserted in and removed from the running kernel whenever you + want). Most people won't need this and can say N. + +config NET_IPGRE_DEMUX + tristate "IP: GRE demultiplexer" + help + This is helper module to demultiplex GRE packets on GRE version field criteria. + Required by ip_gre and pptp modules. + +config NET_IP_TUNNEL + tristate + select DST_CACHE + select GRO_CELLS + default n + +config NET_IPGRE + tristate "IP: GRE tunnels over IP" + depends on (IPV6 || IPV6=n) && NET_IPGRE_DEMUX + select NET_IP_TUNNEL + help + Tunneling means encapsulating data of one protocol type within + another protocol and sending it over a channel that understands the + encapsulating protocol. This particular tunneling driver implements + GRE (Generic Routing Encapsulation) and at this time allows + encapsulating of IPv4 or IPv6 over existing IPv4 infrastructure. + This driver is useful if the other endpoint is a Cisco router: Cisco + likes GRE much better than the other Linux tunneling driver ("IP + tunneling" above). In addition, GRE allows multicast redistribution + through the tunnel. + +config NET_IPGRE_BROADCAST + bool "IP: broadcast GRE over IP" + depends on IP_MULTICAST && NET_IPGRE + help + One application of GRE/IP is to construct a broadcast WAN (Wide Area + Network), which looks like a normal Ethernet LAN (Local Area + Network), but can be distributed all over the Internet. If you want + to do that, say Y here and to "IP multicast routing" below. + +config IP_MROUTE_COMMON + bool + depends on IP_MROUTE || IPV6_MROUTE + +config IP_MROUTE + bool "IP: multicast routing" + depends on IP_MULTICAST + select IP_MROUTE_COMMON + help + This is used if you want your machine to act as a router for IP + packets that have several destination addresses. It is needed on the + MBONE, a high bandwidth network on top of the Internet which carries + audio and video broadcasts. In order to do that, you would most + likely run the program mrouted. If you haven't heard about it, you + don't need it. + +config IP_MROUTE_MULTIPLE_TABLES + bool "IP: multicast policy routing" + depends on IP_MROUTE && IP_ADVANCED_ROUTER + select FIB_RULES + help + Normally, a multicast router runs a userspace daemon and decides + what to do with a multicast packet based on the source and + destination addresses. If you say Y here, the multicast router + will also be able to take interfaces and packet marks into + account and run multiple instances of userspace daemons + simultaneously, each one handling a single table. + + If unsure, say N. + +config IP_PIMSM_V1 + bool "IP: PIM-SM version 1 support" + depends on IP_MROUTE + help + Kernel side support for Sparse Mode PIM (Protocol Independent + Multicast) version 1. This multicast routing protocol is used widely + because Cisco supports it. You need special software to use it + (pimd-v1). Please see <http://netweb.usc.edu/pim/> for more + information about PIM. + + Say Y if you want to use PIM-SM v1. Note that you can say N here if + you just want to use Dense Mode PIM. + +config IP_PIMSM_V2 + bool "IP: PIM-SM version 2 support" + depends on IP_MROUTE + help + Kernel side support for Sparse Mode PIM version 2. In order to use + this, you need an experimental routing daemon supporting it (pimd or + gated-5). This routing protocol is not used widely, so say N unless + you want to play with it. + +config SYN_COOKIES + bool "IP: TCP syncookie support" + help + Normal TCP/IP networking is open to an attack known as "SYN + flooding". This denial-of-service attack prevents legitimate remote + users from being able to connect to your computer during an ongoing + attack and requires very little work from the attacker, who can + operate from anywhere on the Internet. + + SYN cookies provide protection against this type of attack. If you + say Y here, the TCP/IP stack will use a cryptographic challenge + protocol known as "SYN cookies" to enable legitimate users to + continue to connect, even when your machine is under attack. There + is no need for the legitimate users to change their TCP/IP software; + SYN cookies work transparently to them. For technical information + about SYN cookies, check out <https://cr.yp.to/syncookies.html>. + + If you are SYN flooded, the source address reported by the kernel is + likely to have been forged by the attacker; it is only reported as + an aid in tracing the packets to their actual source and should not + be taken as absolute truth. + + SYN cookies may prevent correct error reporting on clients when the + server is really overloaded. If this happens frequently better turn + them off. + + If you say Y here, you can disable SYN cookies at run time by + saying Y to "/proc file system support" and + "Sysctl support" below and executing the command + + echo 0 > /proc/sys/net/ipv4/tcp_syncookies + + after the /proc file system has been mounted. + + If unsure, say N. + +config NET_IPVTI + tristate "Virtual (secure) IP: tunneling" + depends on IPV6 || IPV6=n + select INET_TUNNEL + select NET_IP_TUNNEL + select XFRM + help + Tunneling means encapsulating data of one protocol type within + another protocol and sending it over a channel that understands the + encapsulating protocol. This can be used with xfrm mode tunnel to give + the notion of a secure tunnel for IPSEC and then use routing protocol + on top. + +config NET_UDP_TUNNEL + tristate + select NET_IP_TUNNEL + default n + +config NET_FOU + tristate "IP: Foo (IP protocols) over UDP" + select NET_UDP_TUNNEL + help + Foo over UDP allows any IP protocol to be directly encapsulated + over UDP include tunnels (IPIP, GRE, SIT). By encapsulating in UDP + network mechanisms and optimizations for UDP (such as ECMP + and RSS) can be leveraged to provide better service. + +config NET_FOU_IP_TUNNELS + bool "IP: FOU encapsulation of IP tunnels" + depends on NET_IPIP || NET_IPGRE || IPV6_SIT + select NET_FOU + help + Allow configuration of FOU or GUE encapsulation for IP tunnels. + When this option is enabled IP tunnels can be configured to use + FOU or GUE encapsulation. + +config INET_AH + tristate "IP: AH transformation" + select XFRM_AH + help + Support for IPsec AH (Authentication Header). + + AH can be used with various authentication algorithms. Besides + enabling AH support itself, this option enables the generic + implementations of the algorithms that RFC 8221 lists as MUST be + implemented. If you need any other algorithms, you'll need to enable + them in the crypto API. You should also enable accelerated + implementations of any needed algorithms when available. + + If unsure, say Y. + +config INET_ESP + tristate "IP: ESP transformation" + select XFRM_ESP + help + Support for IPsec ESP (Encapsulating Security Payload). + + ESP can be used with various encryption and authentication algorithms. + Besides enabling ESP support itself, this option enables the generic + implementations of the algorithms that RFC 8221 lists as MUST be + implemented. If you need any other algorithms, you'll need to enable + them in the crypto API. You should also enable accelerated + implementations of any needed algorithms when available. + + If unsure, say Y. + +config INET_ESP_OFFLOAD + tristate "IP: ESP transformation offload" + depends on INET_ESP + select XFRM_OFFLOAD + default n + help + Support for ESP transformation offload. This makes sense + only if this system really does IPsec and want to do it + with high throughput. A typical desktop system does not + need it, even if it does IPsec. + + If unsure, say N. + +config INET_ESPINTCP + bool "IP: ESP in TCP encapsulation (RFC 8229)" + depends on XFRM && INET_ESP + select STREAM_PARSER + select NET_SOCK_MSG + select XFRM_ESPINTCP + help + Support for RFC 8229 encapsulation of ESP and IKE over + TCP/IPv4 sockets. + + If unsure, say N. + +config INET_IPCOMP + tristate "IP: IPComp transformation" + select INET_XFRM_TUNNEL + select XFRM_IPCOMP + help + Support for IP Payload Compression Protocol (IPComp) (RFC3173), + typically needed for IPsec. + + If unsure, say Y. + +config INET_TABLE_PERTURB_ORDER + int "INET: Source port perturbation table size (as power of 2)" if EXPERT + default 16 + help + Source port perturbation table size (as power of 2) for + RFC 6056 3.3.4. Algorithm 4: Double-Hash Port Selection Algorithm. + + The default is almost always what you want. + Only change this if you know what you are doing. + +config INET_XFRM_TUNNEL + tristate + select INET_TUNNEL + default n + +config INET_TUNNEL + tristate + default n + +config INET_DIAG + tristate "INET: socket monitoring interface" + default y + help + Support for INET (TCP, DCCP, etc) socket monitoring interface used by + native Linux tools such as ss. ss is included in iproute2, currently + downloadable at: + + http://www.linuxfoundation.org/collaborate/workgroups/networking/iproute2 + + If unsure, say Y. + +config INET_TCP_DIAG + depends on INET_DIAG + def_tristate INET_DIAG + +config INET_UDP_DIAG + tristate "UDP: socket monitoring interface" + depends on INET_DIAG && (IPV6 || IPV6=n) + default n + help + Support for UDP socket monitoring interface used by the ss tool. + If unsure, say Y. + +config INET_RAW_DIAG + tristate "RAW: socket monitoring interface" + depends on INET_DIAG && (IPV6 || IPV6=n) + default n + help + Support for RAW socket monitoring interface used by the ss tool. + If unsure, say Y. + +config INET_DIAG_DESTROY + bool "INET: allow privileged process to administratively close sockets" + depends on INET_DIAG + default n + help + Provides a SOCK_DESTROY operation that allows privileged processes + (e.g., a connection manager or a network administration tool such as + ss) to close sockets opened by other processes. Closing a socket in + this way interrupts any blocking read/write/connect operations on + the socket and causes future socket calls to behave as if the socket + had been disconnected. + If unsure, say N. + +menuconfig TCP_CONG_ADVANCED + bool "TCP: advanced congestion control" + help + Support for selection of various TCP congestion control + modules. + + Nearly all users can safely say no here, and a safe default + selection will be made (CUBIC with new Reno as a fallback). + + If unsure, say N. + +if TCP_CONG_ADVANCED + +config TCP_CONG_BIC + tristate "Binary Increase Congestion (BIC) control" + default m + help + BIC-TCP is a sender-side only change that ensures a linear RTT + fairness under large windows while offering both scalability and + bounded TCP-friendliness. The protocol combines two schemes + called additive increase and binary search increase. When the + congestion window is large, additive increase with a large + increment ensures linear RTT fairness as well as good + scalability. Under small congestion windows, binary search + increase provides TCP friendliness. + See http://www.csc.ncsu.edu/faculty/rhee/export/bitcp/ + +config TCP_CONG_CUBIC + tristate "CUBIC TCP" + default y + help + This is version 2.0 of BIC-TCP which uses a cubic growth function + among other techniques. + See http://www.csc.ncsu.edu/faculty/rhee/export/bitcp/cubic-paper.pdf + +config TCP_CONG_WESTWOOD + tristate "TCP Westwood+" + default m + help + TCP Westwood+ is a sender-side only modification of the TCP Reno + protocol stack that optimizes the performance of TCP congestion + control. It is based on end-to-end bandwidth estimation to set + congestion window and slow start threshold after a congestion + episode. Using this estimation, TCP Westwood+ adaptively sets a + slow start threshold and a congestion window which takes into + account the bandwidth used at the time congestion is experienced. + TCP Westwood+ significantly increases fairness wrt TCP Reno in + wired networks and throughput over wireless links. + +config TCP_CONG_HTCP + tristate "H-TCP" + default m + help + H-TCP is a send-side only modifications of the TCP Reno + protocol stack that optimizes the performance of TCP + congestion control for high speed network links. It uses a + modeswitch to change the alpha and beta parameters of TCP Reno + based on network conditions and in a way so as to be fair with + other Reno and H-TCP flows. + +config TCP_CONG_HSTCP + tristate "High Speed TCP" + default n + help + Sally Floyd's High Speed TCP (RFC 3649) congestion control. + A modification to TCP's congestion control mechanism for use + with large congestion windows. A table indicates how much to + increase the congestion window by when an ACK is received. + For more detail see https://www.icir.org/floyd/hstcp.html + +config TCP_CONG_HYBLA + tristate "TCP-Hybla congestion control algorithm" + default n + help + TCP-Hybla is a sender-side only change that eliminates penalization of + long-RTT, large-bandwidth connections, like when satellite legs are + involved, especially when sharing a common bottleneck with normal + terrestrial connections. + +config TCP_CONG_VEGAS + tristate "TCP Vegas" + default n + help + TCP Vegas is a sender-side only change to TCP that anticipates + the onset of congestion by estimating the bandwidth. TCP Vegas + adjusts the sending rate by modifying the congestion + window. TCP Vegas should provide less packet loss, but it is + not as aggressive as TCP Reno. + +config TCP_CONG_NV + tristate "TCP NV" + default n + help + TCP NV is a follow up to TCP Vegas. It has been modified to deal with + 10G networks, measurement noise introduced by LRO, GRO and interrupt + coalescence. In addition, it will decrease its cwnd multiplicatively + instead of linearly. + + Note that in general congestion avoidance (cwnd decreased when # packets + queued grows) cannot coexist with congestion control (cwnd decreased only + when there is packet loss) due to fairness issues. One scenario when they + can coexist safely is when the CA flows have RTTs << CC flows RTTs. + + For further details see http://www.brakmo.org/networking/tcp-nv/ + +config TCP_CONG_SCALABLE + tristate "Scalable TCP" + default n + help + Scalable TCP is a sender-side only change to TCP which uses a + MIMD congestion control algorithm which has some nice scaling + properties, though is known to have fairness issues. + See http://www.deneholme.net/tom/scalable/ + +config TCP_CONG_LP + tristate "TCP Low Priority" + default n + help + TCP Low Priority (TCP-LP), a distributed algorithm whose goal is + to utilize only the excess network bandwidth as compared to the + ``fair share`` of bandwidth as targeted by TCP. + See http://www-ece.rice.edu/networks/TCP-LP/ + +config TCP_CONG_VENO + tristate "TCP Veno" + default n + help + TCP Veno is a sender-side only enhancement of TCP to obtain better + throughput over wireless networks. TCP Veno makes use of state + distinguishing to circumvent the difficult judgment of the packet loss + type. TCP Veno cuts down less congestion window in response to random + loss packets. + See <http://ieeexplore.ieee.org/xpl/freeabs_all.jsp?arnumber=1177186> + +config TCP_CONG_YEAH + tristate "YeAH TCP" + select TCP_CONG_VEGAS + default n + help + YeAH-TCP is a sender-side high-speed enabled TCP congestion control + algorithm, which uses a mixed loss/delay approach to compute the + congestion window. It's design goals target high efficiency, + internal, RTT and Reno fairness, resilience to link loss while + keeping network elements load as low as possible. + + For further details look here: + http://wil.cs.caltech.edu/pfldnet2007/paper/YeAH_TCP.pdf + +config TCP_CONG_ILLINOIS + tristate "TCP Illinois" + default n + help + TCP-Illinois is a sender-side modification of TCP Reno for + high speed long delay links. It uses round-trip-time to + adjust the alpha and beta parameters to achieve a higher average + throughput and maintain fairness. + + For further details see: + http://www.ews.uiuc.edu/~shaoliu/tcpillinois/index.html + +config TCP_CONG_DCTCP + tristate "DataCenter TCP (DCTCP)" + default n + help + DCTCP leverages Explicit Congestion Notification (ECN) in the network to + provide multi-bit feedback to the end hosts. It is designed to provide: + + - High burst tolerance (incast due to partition/aggregate), + - Low latency (short flows, queries), + - High throughput (continuous data updates, large file transfers) with + commodity, shallow-buffered switches. + + All switches in the data center network running DCTCP must support + ECN marking and be configured for marking when reaching defined switch + buffer thresholds. The default ECN marking threshold heuristic for + DCTCP on switches is 20 packets (30KB) at 1Gbps, and 65 packets + (~100KB) at 10Gbps, but might need further careful tweaking. + + For further details see: + http://simula.stanford.edu/~alizade/Site/DCTCP_files/dctcp-final.pdf + +config TCP_CONG_CDG + tristate "CAIA Delay-Gradient (CDG)" + default n + help + CAIA Delay-Gradient (CDG) is a TCP congestion control that modifies + the TCP sender in order to: + + o Use the delay gradient as a congestion signal. + o Back off with an average probability that is independent of the RTT. + o Coexist with flows that use loss-based congestion control. + o Tolerate packet loss unrelated to congestion. + + For further details see: + D.A. Hayes and G. Armitage. "Revisiting TCP congestion control using + delay gradients." In Networking 2011. Preprint: http://goo.gl/No3vdg + +config TCP_CONG_BBR + tristate "BBR TCP" + default n + help + + BBR (Bottleneck Bandwidth and RTT) TCP congestion control aims to + maximize network utilization and minimize queues. It builds an explicit + model of the bottleneck delivery rate and path round-trip propagation + delay. It tolerates packet loss and delay unrelated to congestion. It + can operate over LAN, WAN, cellular, wifi, or cable modem links. It can + coexist with flows that use loss-based congestion control, and can + operate with shallow buffers, deep buffers, bufferbloat, policers, or + AQM schemes that do not provide a delay signal. It requires the fq + ("Fair Queue") pacing packet scheduler. + +choice + prompt "Default TCP congestion control" + default DEFAULT_CUBIC + help + Select the TCP congestion control that will be used by default + for all connections. + + config DEFAULT_BIC + bool "Bic" if TCP_CONG_BIC=y + + config DEFAULT_CUBIC + bool "Cubic" if TCP_CONG_CUBIC=y + + config DEFAULT_HTCP + bool "Htcp" if TCP_CONG_HTCP=y + + config DEFAULT_HYBLA + bool "Hybla" if TCP_CONG_HYBLA=y + + config DEFAULT_VEGAS + bool "Vegas" if TCP_CONG_VEGAS=y + + config DEFAULT_VENO + bool "Veno" if TCP_CONG_VENO=y + + config DEFAULT_WESTWOOD + bool "Westwood" if TCP_CONG_WESTWOOD=y + + config DEFAULT_DCTCP + bool "DCTCP" if TCP_CONG_DCTCP=y + + config DEFAULT_CDG + bool "CDG" if TCP_CONG_CDG=y + + config DEFAULT_BBR + bool "BBR" if TCP_CONG_BBR=y + + config DEFAULT_RENO + bool "Reno" +endchoice + +endif + +config TCP_CONG_CUBIC + tristate + depends on !TCP_CONG_ADVANCED + default y + +config DEFAULT_TCP_CONG + string + default "bic" if DEFAULT_BIC + default "cubic" if DEFAULT_CUBIC + default "htcp" if DEFAULT_HTCP + default "hybla" if DEFAULT_HYBLA + default "vegas" if DEFAULT_VEGAS + default "westwood" if DEFAULT_WESTWOOD + default "veno" if DEFAULT_VENO + default "reno" if DEFAULT_RENO + default "dctcp" if DEFAULT_DCTCP + default "cdg" if DEFAULT_CDG + default "bbr" if DEFAULT_BBR + default "cubic" + +config TCP_MD5SIG + bool "TCP: MD5 Signature Option support (RFC2385)" + select CRYPTO + select CRYPTO_MD5 + help + RFC2385 specifies a method of giving MD5 protection to TCP sessions. + Its main (only?) use is to protect BGP sessions between core routers + on the Internet. + + If unsure, say N. |