From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- .../devicetree/bindings/net/qca,qca7000.txt | 87 ++++++++++++++++++++++ 1 file changed, 87 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/qca,qca7000.txt (limited to 'Documentation/devicetree/bindings/net/qca,qca7000.txt') diff --git a/Documentation/devicetree/bindings/net/qca,qca7000.txt b/Documentation/devicetree/bindings/net/qca,qca7000.txt new file mode 100644 index 000000000..8f5ae0b84 --- /dev/null +++ b/Documentation/devicetree/bindings/net/qca,qca7000.txt @@ -0,0 +1,87 @@ +* Qualcomm QCA7000 + +The QCA7000 is a serial-to-powerline bridge with a host interface which could +be configured either as SPI or UART slave. This configuration is done by +the QCA7000 firmware. + +(a) Ethernet over SPI + +In order to use the QCA7000 as SPI device it must be defined as a child of a +SPI master in the device tree. + +Required properties: +- compatible : Should be "qca,qca7000" +- reg : Should specify the SPI chip select +- interrupts : The first cell should specify the index of the source + interrupt and the second cell should specify the trigger + type as rising edge +- spi-cpha : Must be set +- spi-cpol : Must be set + +Optional properties: +- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at. + Numbers smaller than 1000000 or greater than 16000000 + are invalid. Missing the property will set the SPI + frequency to 8000000 Hertz. +- qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode. + In this mode the SPI master must toggle the chip select + between each data word. In burst mode these gaps aren't + necessary, which is faster. This setting depends on how + the QCA7000 is setup via GPIO pin strapping. If the + property is missing the driver defaults to burst mode. + +The MAC address will be determined using the optional properties +defined in ethernet.txt. + +SPI Example: + +/* Freescale i.MX28 SPI master*/ +ssp2: spi@80014000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + + qca7000: ethernet@0 { + compatible = "qca,qca7000"; + reg = <0x0>; + interrupt-parent = <&gpio3>; /* GPIO Bank 3 */ + interrupts = <25 0x1>; /* Index: 25, rising edge */ + spi-cpha; /* SPI mode: CPHA=1 */ + spi-cpol; /* SPI mode: CPOL=1 */ + spi-max-frequency = <8000000>; /* freq: 8 MHz */ + local-mac-address = [ A0 B0 C0 D0 E0 F0 ]; + }; +}; + +(b) Ethernet over UART + +In order to use the QCA7000 as UART slave it must be defined as a child of a +UART master in the device tree. It is possible to preconfigure the UART +settings of the QCA7000 firmware, but it's not possible to change them during +runtime. + +Required properties: +- compatible : Should be "qca,qca7000" + +Optional properties: +- local-mac-address : see ./ethernet.txt +- current-speed : current baud rate of QCA7000 which defaults to 115200 + if absent, see also ../serial/serial.yaml + +UART Example: + +/* Freescale i.MX28 UART */ +auart0: serial@8006a000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x8006a000 0x2000>; + pinctrl-names = "default"; + pinctrl-0 = <&auart0_2pins_a>; + + qca7000: ethernet { + compatible = "qca,qca7000"; + local-mac-address = [ A0 B0 C0 D0 E0 F0 ]; + current-speed = <38400>; + }; +}; -- cgit v1.2.3