From 116e0f61852489520aaad930b8fcbe40834819bf Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sat, 4 May 2024 12:10:26 +0200 Subject: Merging upstream version 6.1.82. Signed-off-by: Daniel Baumann --- arch/x86/boot/compressed/head_64.S | 593 +++++++------------------------------ 1 file changed, 104 insertions(+), 489 deletions(-) (limited to 'arch/x86/boot/compressed/head_64.S') diff --git a/arch/x86/boot/compressed/head_64.S b/arch/x86/boot/compressed/head_64.S index b4bd6df29..0d7aef10b 100644 --- a/arch/x86/boot/compressed/head_64.S +++ b/arch/x86/boot/compressed/head_64.S @@ -118,7 +118,9 @@ SYM_FUNC_START(startup_32) 1: /* Setup Exception handling for SEV-ES */ +#ifdef CONFIG_AMD_MEM_ENCRYPT call startup32_load_idt +#endif /* Make sure cpu supports long mode. */ call verify_cpu @@ -136,19 +138,6 @@ SYM_FUNC_START(startup_32) #ifdef CONFIG_RELOCATABLE movl %ebp, %ebx - -#ifdef CONFIG_EFI_STUB -/* - * If we were loaded via the EFI LoadImage service, startup_32 will be at an - * offset to the start of the space allocated for the image. efi_pe_entry will - * set up image_offset to tell us where the image actually starts, so that we - * can use the full available buffer. - * image_offset = startup_32 - image_base - * Otherwise image_offset will be zero and has no effect on the calculations. - */ - subl rva(image_offset)(%ebp), %ebx -#endif - movl BP_kernel_alignment(%esi), %eax decl %eax addl %eax, %ebx @@ -178,12 +167,13 @@ SYM_FUNC_START(startup_32) */ /* * If SEV is active then set the encryption mask in the page tables. - * This will insure that when the kernel is copied and decompressed + * This will ensure that when the kernel is copied and decompressed * it will be done so encrypted. */ - call get_sev_encryption_bit xorl %edx, %edx #ifdef CONFIG_AMD_MEM_ENCRYPT + call get_sev_encryption_bit + xorl %edx, %edx testl %eax, %eax jz 1f subl $32, %eax /* Encryption bit is always above bit 31 */ @@ -249,6 +239,11 @@ SYM_FUNC_START(startup_32) movl $__BOOT_TSS, %eax ltr %ax +#ifdef CONFIG_AMD_MEM_ENCRYPT + /* Check if the C-bit position is correct when SEV is active */ + call startup32_check_sev_cbit +#endif + /* * Setup for the jump to 64bit mode * @@ -261,29 +256,11 @@ SYM_FUNC_START(startup_32) */ leal rva(startup_64)(%ebp), %eax #ifdef CONFIG_EFI_MIXED - movl rva(efi32_boot_args)(%ebp), %edi - testl %edi, %edi - jz 1f - leal rva(efi64_stub_entry)(%ebp), %eax - movl rva(efi32_boot_args+4)(%ebp), %esi - movl rva(efi32_boot_args+8)(%ebp), %edx // saved bootparams pointer - testl %edx, %edx - jnz 1f - /* - * efi_pe_entry uses MS calling convention, which requires 32 bytes of - * shadow space on the stack even if all arguments are passed in - * registers. We also need an additional 8 bytes for the space that - * would be occupied by the return address, and this also results in - * the correct stack alignment for entry. - */ - subl $40, %esp - leal rva(efi_pe_entry)(%ebp), %eax - movl %edi, %ecx // MS calling convention - movl %esi, %edx + cmpb $1, rva(efi_is64)(%ebp) + je 1f + leal rva(startup_64_mixed_mode)(%ebp), %eax 1: #endif - /* Check if the C-bit position is correct when SEV is active */ - call startup32_check_sev_cbit pushl $__KERNEL_CS pushl %eax @@ -296,41 +273,6 @@ SYM_FUNC_START(startup_32) lret SYM_FUNC_END(startup_32) -#ifdef CONFIG_EFI_MIXED - .org 0x190 -SYM_FUNC_START(efi32_stub_entry) - add $0x4, %esp /* Discard return address */ - popl %ecx - popl %edx - popl %esi - - call 1f -1: pop %ebp - subl $ rva(1b), %ebp - - movl %esi, rva(efi32_boot_args+8)(%ebp) -SYM_INNER_LABEL(efi32_pe_stub_entry, SYM_L_LOCAL) - movl %ecx, rva(efi32_boot_args)(%ebp) - movl %edx, rva(efi32_boot_args+4)(%ebp) - movb $0, rva(efi_is64)(%ebp) - - /* Save firmware GDTR and code/data selectors */ - sgdtl rva(efi32_boot_gdt)(%ebp) - movw %cs, rva(efi32_boot_cs)(%ebp) - movw %ds, rva(efi32_boot_ds)(%ebp) - - /* Store firmware IDT descriptor */ - sidtl rva(efi32_boot_idt)(%ebp) - - /* Disable paging */ - movl %cr0, %eax - btrl $X86_CR0_PG_BIT, %eax - movl %eax, %cr0 - - jmp startup_32 -SYM_FUNC_END(efi32_stub_entry) -#endif - .code64 .org 0x200 SYM_CODE_START(startup_64) @@ -372,20 +314,6 @@ SYM_CODE_START(startup_64) /* Start with the delta to where the kernel will run at. */ #ifdef CONFIG_RELOCATABLE leaq startup_32(%rip) /* - $startup_32 */, %rbp - -#ifdef CONFIG_EFI_STUB -/* - * If we were loaded via the EFI LoadImage service, startup_32 will be at an - * offset to the start of the space allocated for the image. efi_pe_entry will - * set up image_offset to tell us where the image actually starts, so that we - * can use the full available buffer. - * image_offset = startup_32 - image_base - * Otherwise image_offset will be zero and has no effect on the calculations. - */ - movl image_offset(%rip), %eax - subq %rax, %rbp -#endif - movl BP_kernel_alignment(%rsi), %eax decl %eax addq %rax, %rbp @@ -424,10 +352,6 @@ SYM_CODE_START(startup_64) * For the trampoline, we need the top page table to reside in lower * memory as we don't have a way to load 64-bit values into CR3 in * 32-bit mode. - * - * We go though the trampoline even if we don't have to: if we're - * already in a desired paging mode. This way the trampoline code gets - * tested on every boot. */ /* Make sure we have GDT with 32-bit code segment */ @@ -442,10 +366,14 @@ SYM_CODE_START(startup_64) lretq .Lon_kernel_cs: + /* + * RSI holds a pointer to a boot_params structure provided by the + * loader, and this needs to be preserved across C function calls. So + * move it into a callee saved register. + */ + movq %rsi, %r15 - pushq %rsi call load_stage1_idt - popq %rsi #ifdef CONFIG_AMD_MEM_ENCRYPT /* @@ -456,82 +384,24 @@ SYM_CODE_START(startup_64) * CPUID instructions being issued, so go ahead and do that now via * sev_enable(), which will also handle the rest of the SEV-related * detection/setup to ensure that has been done in advance of any dependent - * code. + * code. Pass the boot_params pointer as the first argument. */ - pushq %rsi - movq %rsi, %rdi /* real mode address */ + movq %r15, %rdi call sev_enable - popq %rsi #endif /* - * paging_prepare() sets up the trampoline and checks if we need to - * enable 5-level paging. - * - * paging_prepare() returns a two-quadword structure which lands - * into RDX:RAX: - * - Address of the trampoline is returned in RAX. - * - Non zero RDX means trampoline needs to enable 5-level - * paging. - * - * RSI holds real mode data and needs to be preserved across - * this function call. - */ - pushq %rsi - movq %rsi, %rdi /* real mode address */ - call paging_prepare - popq %rsi - - /* Save the trampoline address in RCX */ - movq %rax, %rcx - - /* Set up 32-bit addressable stack */ - leaq TRAMPOLINE_32BIT_STACK_END(%rcx), %rsp - - /* - * Preserve live 64-bit registers on the stack: this is necessary - * because the architecture does not guarantee that GPRs will retain - * their full 64-bit values across a 32-bit mode switch. - */ - pushq %rbp - pushq %rbx - pushq %rsi - - /* - * Push the 64-bit address of trampoline_return() onto the new stack. - * It will be used by the trampoline to return to the main code. Due to - * the 32-bit mode switch, it cannot be kept it in a register either. - */ - leaq trampoline_return(%rip), %rdi - pushq %rdi - - /* Switch to compatibility mode (CS.L = 0 CS.D = 1) via far return */ - pushq $__KERNEL32_CS - leaq TRAMPOLINE_32BIT_CODE_OFFSET(%rax), %rax - pushq %rax - lretq -trampoline_return: - /* Restore live 64-bit registers */ - popq %rsi - popq %rbx - popq %rbp - - /* Restore the stack, the 32-bit trampoline uses its own stack */ - leaq rva(boot_stack_end)(%rbx), %rsp - - /* - * cleanup_trampoline() would restore trampoline memory. - * - * RDI is address of the page table to use instead of page table - * in trampoline memory (if required). + * configure_5level_paging() updates the number of paging levels using + * a trampoline in 32-bit addressable memory if the current number does + * not match the desired number. * - * RSI holds real mode data and needs to be preserved across - * this function call. + * Pass the boot_params pointer as the first argument. The second + * argument is the relocated address of the page table to use instead + * of the page table in trampoline memory (if required). */ - pushq %rsi - leaq rva(top_pgtable)(%rbx), %rdi - call cleanup_trampoline - popq %rsi + movq %r15, %rdi + leaq rva(top_pgtable)(%rbx), %rsi + call configure_5level_paging /* Zero EFLAGS */ pushq $0 @@ -541,7 +411,6 @@ trampoline_return: * Copy the compressed kernel to the end of our buffer * where decompression in place becomes safe. */ - pushq %rsi leaq (_bss-8)(%rip), %rsi leaq rva(_bss-8)(%rbx), %rdi movl $(_bss - startup_32), %ecx @@ -549,7 +418,6 @@ trampoline_return: std rep movsq cld - popq %rsi /* * The GDT may get overwritten either during the copy we just did or @@ -568,19 +436,6 @@ trampoline_return: jmp *%rax SYM_CODE_END(startup_64) -#ifdef CONFIG_EFI_STUB - .org 0x390 -SYM_FUNC_START(efi64_stub_entry) - and $~0xf, %rsp /* realign the stack */ - movq %rdx, %rbx /* save boot_params pointer */ - call efi_main - movq %rbx,%rsi - leaq rva(startup_64)(%rax), %rax - jmp *%rax -SYM_FUNC_END(efi64_stub_entry) -SYM_FUNC_ALIAS(efi_stub_entry, efi64_stub_entry) -#endif - .text SYM_FUNC_START_LOCAL_NOALIGN(.Lrelocated) @@ -594,125 +449,122 @@ SYM_FUNC_START_LOCAL_NOALIGN(.Lrelocated) shrq $3, %rcx rep stosq - pushq %rsi call load_stage2_idt /* Pass boot_params to initialize_identity_maps() */ - movq (%rsp), %rdi + movq %r15, %rdi call initialize_identity_maps - popq %rsi /* * Do the extraction, and jump to the new kernel.. */ - pushq %rsi /* Save the real mode argument */ - movq %rsi, %rdi /* real mode address */ - leaq boot_heap(%rip), %rsi /* malloc area for uncompression */ - leaq input_data(%rip), %rdx /* input_data */ - movl input_len(%rip), %ecx /* input_len */ - movq %rbp, %r8 /* output target address */ - movl output_len(%rip), %r9d /* decompressed length, end of relocs */ - call extract_kernel /* returns kernel location in %rax */ - popq %rsi + /* pass struct boot_params pointer and output target address */ + movq %r15, %rdi + movq %rbp, %rsi + call extract_kernel /* returns kernel entry point in %rax */ /* * Jump to the decompressed kernel. */ + movq %r15, %rsi jmp *%rax SYM_FUNC_END(.Lrelocated) - .code32 /* - * This is the 32-bit trampoline that will be copied over to low memory. + * This is the 32-bit trampoline that will be copied over to low memory. It + * will be called using the ordinary 64-bit calling convention from code + * running in 64-bit mode. * * Return address is at the top of the stack (might be above 4G). - * ECX contains the base address of the trampoline memory. - * Non zero RDX means trampoline needs to enable 5-level paging. + * The first argument (EDI) contains the address of the temporary PGD level + * page table in 32-bit addressable memory which will be programmed into + * register CR3. */ + .section ".rodata", "a", @progbits SYM_CODE_START(trampoline_32bit_src) - /* Set up data and stack segments */ - movl $__KERNEL_DS, %eax - movl %eax, %ds - movl %eax, %ss + /* + * Preserve callee save 64-bit registers on the stack: this is + * necessary because the architecture does not guarantee that GPRs will + * retain their full 64-bit values across a 32-bit mode switch. + */ + pushq %r15 + pushq %r14 + pushq %r13 + pushq %r12 + pushq %rbp + pushq %rbx + + /* Preserve top half of RSP in a legacy mode GPR to avoid truncation */ + movq %rsp, %rbx + shrq $32, %rbx + /* Switch to compatibility mode (CS.L = 0 CS.D = 1) via far return */ + pushq $__KERNEL32_CS + leaq 0f(%rip), %rax + pushq %rax + lretq + + /* + * The 32-bit code below will do a far jump back to long mode and end + * up here after reconfiguring the number of paging levels. First, the + * stack pointer needs to be restored to its full 64-bit value before + * the callee save register contents can be popped from the stack. + */ +.Lret: + shlq $32, %rbx + orq %rbx, %rsp + + /* Restore the preserved 64-bit registers */ + popq %rbx + popq %rbp + popq %r12 + popq %r13 + popq %r14 + popq %r15 + retq + + .code32 +0: /* Disable paging */ movl %cr0, %eax btrl $X86_CR0_PG_BIT, %eax movl %eax, %cr0 - /* Check what paging mode we want to be in after the trampoline */ - testl %edx, %edx - jz 1f - - /* We want 5-level paging: don't touch CR3 if it already points to 5-level page tables */ - movl %cr4, %eax - testl $X86_CR4_LA57, %eax - jnz 3f - jmp 2f -1: - /* We want 4-level paging: don't touch CR3 if it already points to 4-level page tables */ - movl %cr4, %eax - testl $X86_CR4_LA57, %eax - jz 3f -2: /* Point CR3 to the trampoline's new top level page table */ - leal TRAMPOLINE_32BIT_PGTABLE_OFFSET(%ecx), %eax - movl %eax, %cr3 -3: + movl %edi, %cr3 + /* Set EFER.LME=1 as a precaution in case hypervsior pulls the rug */ - pushl %ecx - pushl %edx movl $MSR_EFER, %ecx rdmsr btsl $_EFER_LME, %eax /* Avoid writing EFER if no change was made (for TDX guest) */ jc 1f wrmsr -1: popl %edx - popl %ecx - -#ifdef CONFIG_X86_MCE - /* - * Preserve CR4.MCE if the kernel will enable #MC support. - * Clearing MCE may fault in some environments (that also force #MC - * support). Any machine check that occurs before #MC support is fully - * configured will crash the system regardless of the CR4.MCE value set - * here. - */ - movl %cr4, %eax - andl $X86_CR4_MCE, %eax -#else - movl $0, %eax -#endif - - /* Enable PAE and LA57 (if required) paging modes */ - orl $X86_CR4_PAE, %eax - testl %edx, %edx - jz 1f - orl $X86_CR4_LA57, %eax 1: + /* Toggle CR4.LA57 */ + movl %cr4, %eax + btcl $X86_CR4_LA57_BIT, %eax movl %eax, %cr4 - /* Calculate address of paging_enabled() once we are executing in the trampoline */ - leal .Lpaging_enabled - trampoline_32bit_src + TRAMPOLINE_32BIT_CODE_OFFSET(%ecx), %eax - - /* Prepare the stack for far return to Long Mode */ - pushl $__KERNEL_CS - pushl %eax - /* Enable paging again. */ movl %cr0, %eax btsl $X86_CR0_PG_BIT, %eax movl %eax, %cr0 - lret + /* + * Return to the 64-bit calling code using LJMP rather than LRET, to + * avoid the need for a 32-bit addressable stack. The destination + * address will be adjusted after the template code is copied into a + * 32-bit addressable buffer. + */ +.Ljmp: ljmpl $__KERNEL_CS, $(.Lret - trampoline_32bit_src) SYM_CODE_END(trampoline_32bit_src) - .code64 -SYM_FUNC_START_LOCAL_NOALIGN(.Lpaging_enabled) - /* Return from the trampoline */ - retq -SYM_FUNC_END(.Lpaging_enabled) +/* + * This symbol is placed right after trampoline_32bit_src() so its address can + * be used to infer the size of the trampoline code. + */ +SYM_DATA(trampoline_ljmp_imm_offset, .word .Ljmp + 1 - trampoline_32bit_src) /* * The trampoline code has a size limit. @@ -721,7 +573,7 @@ SYM_FUNC_END(.Lpaging_enabled) */ .org trampoline_32bit_src + TRAMPOLINE_32BIT_CODE_SIZE - .code32 + .text SYM_FUNC_START_LOCAL_NOALIGN(.Lno_longmode) /* This isn't an x86-64 CPU, so hang intentionally, we cannot continue */ 1: @@ -729,6 +581,7 @@ SYM_FUNC_START_LOCAL_NOALIGN(.Lno_longmode) jmp 1b SYM_FUNC_END(.Lno_longmode) + .globl verify_cpu #include "../../kernel/verify_cpu.S" .data @@ -760,249 +613,11 @@ SYM_DATA_START(boot_idt) .endr SYM_DATA_END_LABEL(boot_idt, SYM_L_GLOBAL, boot_idt_end) -#ifdef CONFIG_AMD_MEM_ENCRYPT -SYM_DATA_START(boot32_idt_desc) - .word boot32_idt_end - boot32_idt - 1 - .long 0 -SYM_DATA_END(boot32_idt_desc) - .balign 8 -SYM_DATA_START(boot32_idt) - .rept 32 - .quad 0 - .endr -SYM_DATA_END_LABEL(boot32_idt, SYM_L_GLOBAL, boot32_idt_end) -#endif - -#ifdef CONFIG_EFI_STUB -SYM_DATA(image_offset, .long 0) -#endif -#ifdef CONFIG_EFI_MIXED -SYM_DATA_LOCAL(efi32_boot_args, .long 0, 0, 0) -SYM_DATA(efi_is64, .byte 1) - -#define ST32_boottime 60 // offsetof(efi_system_table_32_t, boottime) -#define BS32_handle_protocol 88 // offsetof(efi_boot_services_32_t, handle_protocol) -#define LI32_image_base 32 // offsetof(efi_loaded_image_32_t, image_base) - - __HEAD - .code32 -SYM_FUNC_START(efi32_pe_entry) -/* - * efi_status_t efi32_pe_entry(efi_handle_t image_handle, - * efi_system_table_32_t *sys_table) - */ - - pushl %ebp - movl %esp, %ebp - pushl %eax // dummy push to allocate loaded_image - - pushl %ebx // save callee-save registers - pushl %edi - - call verify_cpu // check for long mode support - testl %eax, %eax - movl $0x80000003, %eax // EFI_UNSUPPORTED - jnz 2f - - call 1f -1: pop %ebx - subl $ rva(1b), %ebx - - /* Get the loaded image protocol pointer from the image handle */ - leal -4(%ebp), %eax - pushl %eax // &loaded_image - leal rva(loaded_image_proto)(%ebx), %eax - pushl %eax // pass the GUID address - pushl 8(%ebp) // pass the image handle - - /* - * Note the alignment of the stack frame. - * sys_table - * handle <-- 16-byte aligned on entry by ABI - * return address - * frame pointer - * loaded_image <-- local variable - * saved %ebx <-- 16-byte aligned here - * saved %edi - * &loaded_image - * &loaded_image_proto - * handle <-- 16-byte aligned for call to handle_protocol - */ - - movl 12(%ebp), %eax // sys_table - movl ST32_boottime(%eax), %eax // sys_table->boottime - call *BS32_handle_protocol(%eax) // sys_table->boottime->handle_protocol - addl $12, %esp // restore argument space - testl %eax, %eax - jnz 2f - - movl 8(%ebp), %ecx // image_handle - movl 12(%ebp), %edx // sys_table - movl -4(%ebp), %esi // loaded_image - movl LI32_image_base(%esi), %esi // loaded_image->image_base - movl %ebx, %ebp // startup_32 for efi32_pe_stub_entry - /* - * We need to set the image_offset variable here since startup_32() will - * use it before we get to the 64-bit efi_pe_entry() in C code. - */ - subl %esi, %ebx - movl %ebx, rva(image_offset)(%ebp) // save image_offset - jmp efi32_pe_stub_entry - -2: popl %edi // restore callee-save registers - popl %ebx - leave - RET -SYM_FUNC_END(efi32_pe_entry) - - .section ".rodata" - /* EFI loaded image protocol GUID */ - .balign 4 -SYM_DATA_START_LOCAL(loaded_image_proto) - .long 0x5b1b31a1 - .word 0x9562, 0x11d2 - .byte 0x8e, 0x3f, 0x00, 0xa0, 0xc9, 0x69, 0x72, 0x3b -SYM_DATA_END(loaded_image_proto) -#endif - -#ifdef CONFIG_AMD_MEM_ENCRYPT - __HEAD - .code32 -/* - * Write an IDT entry into boot32_idt - * - * Parameters: - * - * %eax: Handler address - * %edx: Vector number - * - * Physical offset is expected in %ebp - */ -SYM_FUNC_START(startup32_set_idt_entry) - push %ebx - push %ecx - - /* IDT entry address to %ebx */ - leal rva(boot32_idt)(%ebp), %ebx - shl $3, %edx - addl %edx, %ebx - - /* Build IDT entry, lower 4 bytes */ - movl %eax, %edx - andl $0x0000ffff, %edx # Target code segment offset [15:0] - movl $__KERNEL32_CS, %ecx # Target code segment selector - shl $16, %ecx - orl %ecx, %edx - - /* Store lower 4 bytes to IDT */ - movl %edx, (%ebx) - - /* Build IDT entry, upper 4 bytes */ - movl %eax, %edx - andl $0xffff0000, %edx # Target code segment offset [31:16] - orl $0x00008e00, %edx # Present, Type 32-bit Interrupt Gate - - /* Store upper 4 bytes to IDT */ - movl %edx, 4(%ebx) - - pop %ecx - pop %ebx - RET -SYM_FUNC_END(startup32_set_idt_entry) -#endif - -SYM_FUNC_START(startup32_load_idt) -#ifdef CONFIG_AMD_MEM_ENCRYPT - /* #VC handler */ - leal rva(startup32_vc_handler)(%ebp), %eax - movl $X86_TRAP_VC, %edx - call startup32_set_idt_entry - - /* Load IDT */ - leal rva(boot32_idt)(%ebp), %eax - movl %eax, rva(boot32_idt_desc+2)(%ebp) - lidt rva(boot32_idt_desc)(%ebp) -#endif - RET -SYM_FUNC_END(startup32_load_idt) - -/* - * Check for the correct C-bit position when the startup_32 boot-path is used. - * - * The check makes use of the fact that all memory is encrypted when paging is - * disabled. The function creates 64 bits of random data using the RDRAND - * instruction. RDRAND is mandatory for SEV guests, so always available. If the - * hypervisor violates that the kernel will crash right here. - * - * The 64 bits of random data are stored to a memory location and at the same - * time kept in the %eax and %ebx registers. Since encryption is always active - * when paging is off the random data will be stored encrypted in main memory. - * - * Then paging is enabled. When the C-bit position is correct all memory is - * still mapped encrypted and comparing the register values with memory will - * succeed. An incorrect C-bit position will map all memory unencrypted, so that - * the compare will use the encrypted random data and fail. - */ -SYM_FUNC_START(startup32_check_sev_cbit) -#ifdef CONFIG_AMD_MEM_ENCRYPT - pushl %eax - pushl %ebx - pushl %ecx - pushl %edx - - /* Check for non-zero sev_status */ - movl rva(sev_status)(%ebp), %eax - testl %eax, %eax - jz 4f - - /* - * Get two 32-bit random values - Don't bail out if RDRAND fails - * because it is better to prevent forward progress if no random value - * can be gathered. - */ -1: rdrand %eax - jnc 1b -2: rdrand %ebx - jnc 2b - - /* Store to memory and keep it in the registers */ - movl %eax, rva(sev_check_data)(%ebp) - movl %ebx, rva(sev_check_data+4)(%ebp) - - /* Enable paging to see if encryption is active */ - movl %cr0, %edx /* Backup %cr0 in %edx */ - movl $(X86_CR0_PG | X86_CR0_PE), %ecx /* Enable Paging and Protected mode */ - movl %ecx, %cr0 - - cmpl %eax, rva(sev_check_data)(%ebp) - jne 3f - cmpl %ebx, rva(sev_check_data+4)(%ebp) - jne 3f - - movl %edx, %cr0 /* Restore previous %cr0 */ - - jmp 4f - -3: /* Check failed - hlt the machine */ - hlt - jmp 3b - -4: - popl %edx - popl %ecx - popl %ebx - popl %eax -#endif - RET -SYM_FUNC_END(startup32_check_sev_cbit) - /* * Stack and heap for uncompression */ .bss .balign 4 -SYM_DATA_LOCAL(boot_heap, .fill BOOT_HEAP_SIZE, 1, 0) - SYM_DATA_START_LOCAL(boot_stack) .fill BOOT_STACK_SIZE, 1, 0 .balign 16 -- cgit v1.2.3