From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- drivers/media/pci/cx18/cx18-dvb.c | 593 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 593 insertions(+) create mode 100644 drivers/media/pci/cx18/cx18-dvb.c (limited to 'drivers/media/pci/cx18/cx18-dvb.c') diff --git a/drivers/media/pci/cx18/cx18-dvb.c b/drivers/media/pci/cx18/cx18-dvb.c new file mode 100644 index 000000000..33e5a5b5f --- /dev/null +++ b/drivers/media/pci/cx18/cx18-dvb.c @@ -0,0 +1,593 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * cx18 functions for DVB support + * + * Copyright (c) 2008 Steven Toth + * Copyright (C) 2008 Andy Walls + */ + +#include "cx18-version.h" +#include "cx18-dvb.h" +#include "cx18-io.h" +#include "cx18-queue.h" +#include "cx18-streams.h" +#include "cx18-cards.h" +#include "cx18-gpio.h" +#include "s5h1409.h" +#include "mxl5005s.h" +#include "s5h1411.h" +#include "tda18271.h" +#include "zl10353.h" + +#include +#include "mt352.h" +#include "mt352_priv.h" +#include "xc2028.h" + +DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr); + +#define FWFILE "dvb-cx18-mpc718-mt352.fw" + +#define CX18_REG_DMUX_NUM_PORT_0_CONTROL 0xd5a000 +#define CX18_CLOCK_ENABLE2 0xc71024 +#define CX18_DMUX_CLK_MASK 0x0080 + +/* + * CX18_CARD_HVR_1600_ESMT + * CX18_CARD_HVR_1600_SAMSUNG + */ + +static struct mxl5005s_config hauppauge_hvr1600_tuner = { + .i2c_address = 0xC6 >> 1, + .if_freq = IF_FREQ_5380000HZ, + .xtal_freq = CRYSTAL_FREQ_16000000HZ, + .agc_mode = MXL_SINGLE_AGC, + .tracking_filter = MXL_TF_C_H, + .rssi_enable = MXL_RSSI_ENABLE, + .cap_select = MXL_CAP_SEL_ENABLE, + .div_out = MXL_DIV_OUT_4, + .clock_out = MXL_CLOCK_OUT_DISABLE, + .output_load = MXL5005S_IF_OUTPUT_LOAD_200_OHM, + .top = MXL5005S_TOP_25P2, + .mod_mode = MXL_DIGITAL_MODE, + .if_mode = MXL_ZERO_IF, + .qam_gain = 0x02, + .AgcMasterByte = 0x00, +}; + +static struct s5h1409_config hauppauge_hvr1600_config = { + .demod_address = 0x32 >> 1, + .output_mode = S5H1409_SERIAL_OUTPUT, + .gpio = S5H1409_GPIO_ON, + .qam_if = 44000, + .inversion = S5H1409_INVERSION_OFF, + .status_mode = S5H1409_DEMODLOCKING, + .mpeg_timing = S5H1409_MPEGTIMING_CONTINUOUS_NONINVERTING_CLOCK, + .hvr1600_opt = S5H1409_HVR1600_OPTIMIZE +}; + +/* + * CX18_CARD_HVR_1600_S5H1411 + */ +static struct s5h1411_config hcw_s5h1411_config = { + .output_mode = S5H1411_SERIAL_OUTPUT, + .gpio = S5H1411_GPIO_OFF, + .vsb_if = S5H1411_IF_44000, + .qam_if = S5H1411_IF_4000, + .inversion = S5H1411_INVERSION_ON, + .status_mode = S5H1411_DEMODLOCKING, + .mpeg_timing = S5H1411_MPEGTIMING_CONTINUOUS_NONINVERTING_CLOCK, +}; + +static struct tda18271_std_map hauppauge_tda18271_std_map = { + .atsc_6 = { .if_freq = 5380, .agc_mode = 3, .std = 3, + .if_lvl = 6, .rfagc_top = 0x37 }, + .qam_6 = { .if_freq = 4000, .agc_mode = 3, .std = 0, + .if_lvl = 6, .rfagc_top = 0x37 }, +}; + +static struct tda18271_config hauppauge_tda18271_config = { + .std_map = &hauppauge_tda18271_std_map, + .gate = TDA18271_GATE_DIGITAL, + .output_opt = TDA18271_OUTPUT_LT_OFF, +}; + +/* + * CX18_CARD_LEADTEK_DVR3100H + */ +/* Information/confirmation of proper config values provided by Terry Wu */ +static struct zl10353_config leadtek_dvr3100h_demod = { + .demod_address = 0x1e >> 1, /* Datasheet suggested straps */ + .if2 = 45600, /* 4.560 MHz IF from the XC3028 */ + .parallel_ts = 1, /* Not a serial TS */ + .no_tuner = 1, /* XC3028 is not behind the gate */ + .disable_i2c_gate_ctrl = 1, /* Disable the I2C gate */ +}; + +/* + * CX18_CARD_YUAN_MPC718 + */ +/* + * Due to + * + * 1. an absence of information on how to program the MT352 + * 2. the Linux mt352 module pushing MT352 initialization off onto us here + * + * We have to use an init sequence that *you* must extract from the Windows + * driver (yuanrap.sys) and which we load as a firmware. + * + * If someone can provide me with a Zarlink MT352 (Intel CE6352?) Design Manual + * with chip programming details, then I can remove this annoyance. + */ +static int yuan_mpc718_mt352_reqfw(struct cx18_stream *stream, + const struct firmware **fw) +{ + struct cx18 *cx = stream->cx; + const char *fn = FWFILE; + int ret; + + ret = request_firmware(fw, fn, &cx->pci_dev->dev); + if (ret) + CX18_ERR("Unable to open firmware file %s\n", fn); + else { + size_t sz = (*fw)->size; + if (sz < 2 || sz > 64 || (sz % 2) != 0) { + CX18_ERR("Firmware %s has a bad size: %lu bytes\n", + fn, (unsigned long) sz); + ret = -EILSEQ; + release_firmware(*fw); + *fw = NULL; + } + } + + if (ret) { + CX18_ERR("The MPC718 board variant with the MT352 DVB-T demodulator will not work without it\n"); + CX18_ERR("Run 'linux/scripts/get_dvb_firmware mpc718' if you need the firmware\n"); + } + return ret; +} + +static int yuan_mpc718_mt352_init(struct dvb_frontend *fe) +{ + struct cx18_dvb *dvb = container_of(fe->dvb, + struct cx18_dvb, dvb_adapter); + struct cx18_stream *stream = dvb->stream; + const struct firmware *fw = NULL; + int ret; + int i; + u8 buf[3]; + + ret = yuan_mpc718_mt352_reqfw(stream, &fw); + if (ret) + return ret; + + /* Loop through all the register-value pairs in the firmware file */ + for (i = 0; i < fw->size; i += 2) { + buf[0] = fw->data[i]; + /* Intercept a few registers we want to set ourselves */ + switch (buf[0]) { + case TRL_NOMINAL_RATE_0: + /* Set our custom OFDM bandwidth in the case below */ + break; + case TRL_NOMINAL_RATE_1: + /* 6 MHz: 64/7 * 6/8 / 20.48 * 2^16 = 0x55b6.db6 */ + /* 7 MHz: 64/7 * 7/8 / 20.48 * 2^16 = 0x6400 */ + /* 8 MHz: 64/7 * 8/8 / 20.48 * 2^16 = 0x7249.249 */ + buf[1] = 0x72; + buf[2] = 0x49; + mt352_write(fe, buf, 3); + break; + case INPUT_FREQ_0: + /* Set our custom IF in the case below */ + break; + case INPUT_FREQ_1: + /* 4.56 MHz IF: (20.48 - 4.56)/20.48 * 2^14 = 0x31c0 */ + buf[1] = 0x31; + buf[2] = 0xc0; + mt352_write(fe, buf, 3); + break; + default: + /* Pass through the register-value pair from the fw */ + buf[1] = fw->data[i+1]; + mt352_write(fe, buf, 2); + break; + } + } + + buf[0] = (u8) TUNER_GO; + buf[1] = 0x01; /* Go */ + mt352_write(fe, buf, 2); + release_firmware(fw); + return 0; +} + +static struct mt352_config yuan_mpc718_mt352_demod = { + .demod_address = 0x1e >> 1, + .adc_clock = 20480, /* 20.480 MHz */ + .if2 = 4560, /* 4.560 MHz */ + .no_tuner = 1, /* XC3028 is not behind the gate */ + .demod_init = yuan_mpc718_mt352_init, +}; + +static struct zl10353_config yuan_mpc718_zl10353_demod = { + .demod_address = 0x1e >> 1, /* Datasheet suggested straps */ + .if2 = 45600, /* 4.560 MHz IF from the XC3028 */ + .parallel_ts = 1, /* Not a serial TS */ + .no_tuner = 1, /* XC3028 is not behind the gate */ + .disable_i2c_gate_ctrl = 1, /* Disable the I2C gate */ +}; + +static struct zl10353_config gotview_dvd3_zl10353_demod = { + .demod_address = 0x1e >> 1, /* Datasheet suggested straps */ + .if2 = 45600, /* 4.560 MHz IF from the XC3028 */ + .parallel_ts = 1, /* Not a serial TS */ + .no_tuner = 1, /* XC3028 is not behind the gate */ + .disable_i2c_gate_ctrl = 1, /* Disable the I2C gate */ +}; + +static int dvb_register(struct cx18_stream *stream); + +/* Kernel DVB framework calls this when the feed needs to start. + * The CX18 framework should enable the transport DMA handling + * and queue processing. + */ +static int cx18_dvb_start_feed(struct dvb_demux_feed *feed) +{ + struct dvb_demux *demux = feed->demux; + struct cx18_stream *stream = (struct cx18_stream *) demux->priv; + struct cx18 *cx; + int ret; + u32 v; + + if (!stream) + return -EINVAL; + + cx = stream->cx; + CX18_DEBUG_INFO("Start feed: pid = 0x%x index = %d\n", + feed->pid, feed->index); + + mutex_lock(&cx->serialize_lock); + ret = cx18_init_on_first_open(cx); + mutex_unlock(&cx->serialize_lock); + if (ret) { + CX18_ERR("Failed to initialize firmware starting DVB feed\n"); + return ret; + } + ret = -EINVAL; + + switch (cx->card->type) { + case CX18_CARD_HVR_1600_ESMT: + case CX18_CARD_HVR_1600_SAMSUNG: + case CX18_CARD_HVR_1600_S5H1411: + v = cx18_read_reg(cx, CX18_REG_DMUX_NUM_PORT_0_CONTROL); + v |= 0x00400000; /* Serial Mode */ + v |= 0x00002000; /* Data Length - Byte */ + v |= 0x00010000; /* Error - Polarity */ + v |= 0x00020000; /* Error - Passthru */ + v |= 0x000c0000; /* Error - Ignore */ + cx18_write_reg(cx, v, CX18_REG_DMUX_NUM_PORT_0_CONTROL); + break; + + case CX18_CARD_LEADTEK_DVR3100H: + case CX18_CARD_YUAN_MPC718: + case CX18_CARD_GOTVIEW_PCI_DVD3: + default: + /* Assumption - Parallel transport - Signalling + * undefined or default. + */ + break; + } + + if (!demux->dmx.frontend) + return -EINVAL; + + mutex_lock(&stream->dvb->feedlock); + if (stream->dvb->feeding++ == 0) { + CX18_DEBUG_INFO("Starting Transport DMA\n"); + mutex_lock(&cx->serialize_lock); + set_bit(CX18_F_S_STREAMING, &stream->s_flags); + ret = cx18_start_v4l2_encode_stream(stream); + if (ret < 0) { + CX18_DEBUG_INFO("Failed to start Transport DMA\n"); + stream->dvb->feeding--; + if (stream->dvb->feeding == 0) + clear_bit(CX18_F_S_STREAMING, &stream->s_flags); + } + mutex_unlock(&cx->serialize_lock); + } else + ret = 0; + mutex_unlock(&stream->dvb->feedlock); + + return ret; +} + +/* Kernel DVB framework calls this when the feed needs to stop. */ +static int cx18_dvb_stop_feed(struct dvb_demux_feed *feed) +{ + struct dvb_demux *demux = feed->demux; + struct cx18_stream *stream = (struct cx18_stream *)demux->priv; + struct cx18 *cx; + int ret = -EINVAL; + + if (stream) { + cx = stream->cx; + CX18_DEBUG_INFO("Stop feed: pid = 0x%x index = %d\n", + feed->pid, feed->index); + + mutex_lock(&stream->dvb->feedlock); + if (--stream->dvb->feeding == 0) { + CX18_DEBUG_INFO("Stopping Transport DMA\n"); + mutex_lock(&cx->serialize_lock); + ret = cx18_stop_v4l2_encode_stream(stream, 0); + mutex_unlock(&cx->serialize_lock); + } else + ret = 0; + mutex_unlock(&stream->dvb->feedlock); + } + + return ret; +} + +int cx18_dvb_register(struct cx18_stream *stream) +{ + struct cx18 *cx = stream->cx; + struct cx18_dvb *dvb = stream->dvb; + struct dvb_adapter *dvb_adapter; + struct dvb_demux *dvbdemux; + struct dmx_demux *dmx; + int ret; + + if (!dvb) + return -EINVAL; + + dvb->enabled = 0; + dvb->stream = stream; + + ret = dvb_register_adapter(&dvb->dvb_adapter, + CX18_DRIVER_NAME, + THIS_MODULE, &cx->pci_dev->dev, adapter_nr); + if (ret < 0) + goto err_out; + + dvb_adapter = &dvb->dvb_adapter; + + dvbdemux = &dvb->demux; + + dvbdemux->priv = (void *)stream; + + dvbdemux->filternum = 256; + dvbdemux->feednum = 256; + dvbdemux->start_feed = cx18_dvb_start_feed; + dvbdemux->stop_feed = cx18_dvb_stop_feed; + dvbdemux->dmx.capabilities = (DMX_TS_FILTERING | + DMX_SECTION_FILTERING | DMX_MEMORY_BASED_FILTERING); + ret = dvb_dmx_init(dvbdemux); + if (ret < 0) + goto err_dvb_unregister_adapter; + + dmx = &dvbdemux->dmx; + + dvb->hw_frontend.source = DMX_FRONTEND_0; + dvb->mem_frontend.source = DMX_MEMORY_FE; + dvb->dmxdev.filternum = 256; + dvb->dmxdev.demux = dmx; + + ret = dvb_dmxdev_init(&dvb->dmxdev, dvb_adapter); + if (ret < 0) + goto err_dvb_dmx_release; + + ret = dmx->add_frontend(dmx, &dvb->hw_frontend); + if (ret < 0) + goto err_dvb_dmxdev_release; + + ret = dmx->add_frontend(dmx, &dvb->mem_frontend); + if (ret < 0) + goto err_remove_hw_frontend; + + ret = dmx->connect_frontend(dmx, &dvb->hw_frontend); + if (ret < 0) + goto err_remove_mem_frontend; + + ret = dvb_register(stream); + if (ret < 0) + goto err_disconnect_frontend; + + dvb_net_init(dvb_adapter, &dvb->dvbnet, dmx); + + CX18_INFO("DVB Frontend registered\n"); + CX18_INFO("Registered DVB adapter%d for %s (%d x %d.%02d kB)\n", + stream->dvb->dvb_adapter.num, stream->name, + stream->buffers, stream->buf_size/1024, + (stream->buf_size * 100 / 1024) % 100); + + mutex_init(&dvb->feedlock); + dvb->enabled = 1; + return ret; + +err_disconnect_frontend: + dmx->disconnect_frontend(dmx); +err_remove_mem_frontend: + dmx->remove_frontend(dmx, &dvb->mem_frontend); +err_remove_hw_frontend: + dmx->remove_frontend(dmx, &dvb->hw_frontend); +err_dvb_dmxdev_release: + dvb_dmxdev_release(&dvb->dmxdev); +err_dvb_dmx_release: + dvb_dmx_release(dvbdemux); +err_dvb_unregister_adapter: + dvb_unregister_adapter(dvb_adapter); +err_out: + return ret; +} + +void cx18_dvb_unregister(struct cx18_stream *stream) +{ + struct cx18 *cx = stream->cx; + struct cx18_dvb *dvb = stream->dvb; + struct dvb_adapter *dvb_adapter; + struct dvb_demux *dvbdemux; + struct dmx_demux *dmx; + + CX18_INFO("unregister DVB\n"); + + if (dvb == NULL || !dvb->enabled) + return; + + dvb_adapter = &dvb->dvb_adapter; + dvbdemux = &dvb->demux; + dmx = &dvbdemux->dmx; + + dmx->close(dmx); + dvb_net_release(&dvb->dvbnet); + dmx->remove_frontend(dmx, &dvb->mem_frontend); + dmx->remove_frontend(dmx, &dvb->hw_frontend); + dvb_dmxdev_release(&dvb->dmxdev); + dvb_dmx_release(dvbdemux); + dvb_unregister_frontend(dvb->fe); + dvb_frontend_detach(dvb->fe); + dvb_unregister_adapter(dvb_adapter); +} + +/* All the DVB attach calls go here, this function gets modified + * for each new card. cx18_dvb_start_feed() will also need changes. + */ +static int dvb_register(struct cx18_stream *stream) +{ + struct cx18_dvb *dvb = stream->dvb; + struct cx18 *cx = stream->cx; + int ret = 0; + + switch (cx->card->type) { + case CX18_CARD_HVR_1600_ESMT: + case CX18_CARD_HVR_1600_SAMSUNG: + dvb->fe = dvb_attach(s5h1409_attach, + &hauppauge_hvr1600_config, + &cx->i2c_adap[0]); + if (dvb->fe != NULL) { + dvb_attach(mxl5005s_attach, dvb->fe, + &cx->i2c_adap[0], + &hauppauge_hvr1600_tuner); + ret = 0; + } + break; + case CX18_CARD_HVR_1600_S5H1411: + dvb->fe = dvb_attach(s5h1411_attach, + &hcw_s5h1411_config, + &cx->i2c_adap[0]); + if (dvb->fe != NULL) + dvb_attach(tda18271_attach, dvb->fe, + 0x60, &cx->i2c_adap[0], + &hauppauge_tda18271_config); + break; + case CX18_CARD_LEADTEK_DVR3100H: + dvb->fe = dvb_attach(zl10353_attach, + &leadtek_dvr3100h_demod, + &cx->i2c_adap[1]); + if (dvb->fe != NULL) { + struct dvb_frontend *fe; + struct xc2028_config cfg = { + .i2c_adap = &cx->i2c_adap[1], + .i2c_addr = 0xc2 >> 1, + .ctrl = NULL, + }; + static struct xc2028_ctrl ctrl = { + .fname = XC2028_DEFAULT_FIRMWARE, + .max_len = 64, + .demod = XC3028_FE_ZARLINK456, + .type = XC2028_AUTO, + }; + + fe = dvb_attach(xc2028_attach, dvb->fe, &cfg); + if (fe != NULL && fe->ops.tuner_ops.set_config != NULL) + fe->ops.tuner_ops.set_config(fe, &ctrl); + } + break; + case CX18_CARD_YUAN_MPC718: + /* + * TODO + * Apparently, these cards also could instead have a + * DiBcom demod supported by one of the db7000 drivers + */ + dvb->fe = dvb_attach(mt352_attach, + &yuan_mpc718_mt352_demod, + &cx->i2c_adap[1]); + if (dvb->fe == NULL) + dvb->fe = dvb_attach(zl10353_attach, + &yuan_mpc718_zl10353_demod, + &cx->i2c_adap[1]); + if (dvb->fe != NULL) { + struct dvb_frontend *fe; + struct xc2028_config cfg = { + .i2c_adap = &cx->i2c_adap[1], + .i2c_addr = 0xc2 >> 1, + .ctrl = NULL, + }; + static struct xc2028_ctrl ctrl = { + .fname = XC2028_DEFAULT_FIRMWARE, + .max_len = 64, + .demod = XC3028_FE_ZARLINK456, + .type = XC2028_AUTO, + }; + + fe = dvb_attach(xc2028_attach, dvb->fe, &cfg); + if (fe != NULL && fe->ops.tuner_ops.set_config != NULL) + fe->ops.tuner_ops.set_config(fe, &ctrl); + } + break; + case CX18_CARD_GOTVIEW_PCI_DVD3: + dvb->fe = dvb_attach(zl10353_attach, + &gotview_dvd3_zl10353_demod, + &cx->i2c_adap[1]); + if (dvb->fe != NULL) { + struct dvb_frontend *fe; + struct xc2028_config cfg = { + .i2c_adap = &cx->i2c_adap[1], + .i2c_addr = 0xc2 >> 1, + .ctrl = NULL, + }; + static struct xc2028_ctrl ctrl = { + .fname = XC2028_DEFAULT_FIRMWARE, + .max_len = 64, + .demod = XC3028_FE_ZARLINK456, + .type = XC2028_AUTO, + }; + + fe = dvb_attach(xc2028_attach, dvb->fe, &cfg); + if (fe != NULL && fe->ops.tuner_ops.set_config != NULL) + fe->ops.tuner_ops.set_config(fe, &ctrl); + } + break; + default: + /* No Digital Tv Support */ + break; + } + + if (dvb->fe == NULL) { + CX18_ERR("frontend initialization failed\n"); + return -1; + } + + dvb->fe->callback = cx18_reset_tuner_gpio; + + ret = dvb_register_frontend(&dvb->dvb_adapter, dvb->fe); + if (ret < 0) { + if (dvb->fe->ops.release) + dvb->fe->ops.release(dvb->fe); + return ret; + } + + /* + * The firmware seems to enable the TS DMUX clock + * under various circumstances. However, since we know we + * might use it, let's just turn it on ourselves here. + */ + cx18_write_reg_expect(cx, + (CX18_DMUX_CLK_MASK << 16) | CX18_DMUX_CLK_MASK, + CX18_CLOCK_ENABLE2, + CX18_DMUX_CLK_MASK, + (CX18_DMUX_CLK_MASK << 16) | CX18_DMUX_CLK_MASK); + + return ret; +} + +MODULE_FIRMWARE(FWFILE); -- cgit v1.2.3