1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
|
// SPDX-License-Identifier: ISC
/*
* Device Tree file for Iomega NAS 100D
*/
/dts-v1/;
#include "intel-ixp42x.dtsi"
#include <dt-bindings/input/input.h>
/ {
model = "Iomega NAS 100D";
compatible = "iom,nas-100d", "intel,ixp42x";
#address-cells = <1>;
#size-cells = <1>;
memory@0 {
/* 64 MB SDRAM */
device_type = "memory";
reg = <0x00000000 0x4000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
stdout-path = "uart0:115200n8";
};
aliases {
serial0 = &uart0;
};
leds {
compatible = "gpio-leds";
led-wlan {
label = "nas100d:red:wlan";
gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
default-state = "on";
/* We don't have WLAN trigger in the kernel (yet) */
linux,default-trigger = "netdev";
};
led-disk {
label = "nas100d:red:disk";
gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
default-state = "on";
linux,default-trigger = "disk-activity";
};
led-power {
label = "nas100d:red:power";
gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
default-state = "on";
linux,default-trigger = "heartbeat";
};
};
gpio_keys {
compatible = "gpio-keys";
button-power {
wakeup-source;
linux,code = <KEY_POWER>;
label = "power";
gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
};
button-reset {
wakeup-source;
linux,code = <KEY_ESC>;
label = "reset";
gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
};
};
i2c {
compatible = "i2c-gpio";
sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
#address-cells = <1>;
#size-cells = <0>;
rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
};
};
gpio-poweroff {
compatible = "gpio-poweroff";
gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
timeout-ms = <5000>;
};
soc {
bus@c4000000 {
/* The first 16MB region at CS0 on the expansion bus */
flash@0,0 {
compatible = "intel,ixp4xx-flash", "cfi-flash";
bank-width = <2>;
/*
* 8 MB of Flash in 0x20000 byte blocks
* mapped in at CS0.
*/
reg = <0 0x00000000 0x800000>;
partitions {
compatible = "redboot-fis";
/* Eraseblock at 0x7e0000 */
fis-index-block = <0x3f>;
};
};
};
pci@c0000000 {
status = "ok";
/*
* Taken from NAS 100D PCI boardfile (nas100d-pci.c)
* We have slots (IDSEL) 1, 2 and 3 and pins 1, 2 and 3.
*/
#interrupt-cells = <1>;
interrupt-map-mask = <0xf800 0 0 7>;
interrupt-map =
/* IDSEL 1 */
<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
/* IDSEL 2 */
<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
/* IDSEL 3 */
<0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */
<0x1800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */
<0x1800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>; /* INT C on slot 3 is irq 7 */
};
ethernet@c8009000 {
status = "ok";
queue-rx = <&qmgr 3>;
queue-txready = <&qmgr 20>;
phy-mode = "rgmii";
phy-handle = <&phy0>;
mdio {
#address-cells = <1>;
#size-cells = <0>;
phy0: ethernet-phy@0 {
reg = <0>;
};
};
};
};
};
|
