Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 98 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mfd/atmel-usart.txt b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
new file mode 100644
index 000000000..a09133066
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
@@ -0,0 +1,98 @@
+* Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART)
+
+Required properties for USART:
+- compatible: Should be one of the following:
+	- "atmel,at91rm9200-usart"
+	- "atmel,at91sam9260-usart"
+	- "microchip,sam9x60-usart"
+	- "atmel,at91rm9200-dbgu", "atmel,at91rm9200-usart"
+	- "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart"
+	- "microchip,sam9x60-dbgu", "microchip,sam9x60-usart"
+- reg: Should contain registers location and length
+- interrupts: Should contain interrupt
+- clock-names: tuple listing input clock names.
+	Required elements: "usart"
+- clocks: phandles to input clocks.
+
+Required properties for USART in SPI mode:
+- #size-cells      : Must be <0>
+- #address-cells   : Must be <1>
+- cs-gpios: chipselects (internal cs not supported)
+- atmel,usart-mode : Must be <AT91_USART_MODE_SPI> (found in dt-bindings/mfd/at91-usart.h)
+
+Optional properties in serial and SPI mode:
+- dma bindings for dma transfer:
+	- dmas: DMA specifier, consisting of a phandle to DMA controller node,
+		memory peripheral interface and USART DMA channel ID, FIFO configuration.
+		The order of DMA channels is fixed. The first DMA channel must be TX
+		associated channel and the second one must be RX associated channel.
+		Refer to dma.txt and atmel-dma.txt for details.
+	- dma-names: "tx" for TX channel.
+		     "rx" for RX channel.
+		     The order of dma-names is also fixed. The first name must be "tx"
+		     and the second one must be "rx" as in the examples below.
+
+Optional properties in serial mode:
+- atmel,use-dma-rx: use of PDC or DMA for receiving data
+- atmel,use-dma-tx: use of PDC or DMA for transmitting data
+- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively.
+  It will use specified PIO instead of the peripheral function pin for the USART feature.
+  If unsure, don't specify this property.
+- atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO
+  capable USARTs.
+- rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt
+
+<chip> compatible description:
+- at91rm9200:  legacy USART support
+- at91sam9260: generic USART implementation for SAM9 SoCs
+
+Example:
+- use PDC:
+	usart0: serial@fff8c000 {
+		compatible = "atmel,at91sam9260-usart";
+		reg = <0xfff8c000 0x4000>;
+		interrupts = <7>;
+		clocks = <&usart0_clk>;
+		clock-names = "usart";
+		atmel,use-dma-rx;
+		atmel,use-dma-tx;
+		rts-gpios = <&pioD 15 GPIO_ACTIVE_LOW>;
+		cts-gpios = <&pioD 16 GPIO_ACTIVE_LOW>;
+		dtr-gpios = <&pioD 17 GPIO_ACTIVE_LOW>;
+		dsr-gpios = <&pioD 18 GPIO_ACTIVE_LOW>;
+		dcd-gpios = <&pioD 20 GPIO_ACTIVE_LOW>;
+		rng-gpios = <&pioD 19 GPIO_ACTIVE_LOW>;
+	};
+
+- use DMA:
+	usart0: serial@f001c000 {
+		compatible = "atmel,at91sam9260-usart";
+		reg = <0xf001c000 0x100>;
+		interrupts = <12 4 5>;
+		clocks = <&usart0_clk>;
+		clock-names = "usart";
+		atmel,use-dma-rx;
+		atmel,use-dma-tx;
+		dmas = <&dma0 2 0x3>,
+		       <&dma0 2 0x204>;
+		dma-names = "tx", "rx";
+		atmel,fifo-size = <32>;
+	};
+
+- SPI mode:
+	#include <dt-bindings/mfd/at91-usart.h>
+
+	spi0: spi@f001c000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "atmel,at91rm9200-usart", "atmel,at91sam9260-usart";
+		atmel,usart-mode = <AT91_USART_MODE_SPI>;
+		reg = <0xf001c000 0x100>;
+		interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>;
+		clocks = <&usart0_clk>;
+		clock-names = "usart";
+		dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>,
+		       <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+		dma-names = "tx", "rx";
+		cs-gpios = <&pioB 3 0>;
+	};