Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

102 files changed, 10633 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mfd/88pm860x.txt b/Documentation/devicetree/bindings/mfd/88pm860x.txt
new file mode 100644
index 000000000..63f3ee337
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/88pm860x.txt
@@ -0,0 +1,85 @@
+* Marvell 88PM860x Power Management IC
+
+Required parent device properties:
+- compatible : "marvell,88pm860x"
+- reg : the I2C slave address for the 88pm860x chip
+- interrupts : IRQ line for the 88pm860x chip
+- interrupt-controller: describes the 88pm860x as an interrupt controller (has its own domain)
+- #interrupt-cells : should be 1.
+		- The cell is the 88pm860x local IRQ number
+
+Optional parent device properties:
+- marvell,88pm860x-irq-read-clr: inicates whether interrupt status is cleared by read
+- marvell,88pm860x-slave-addr: 88pm860x are two chips solution. <reg> stores the I2C address
+				of one chip, and this property stores the I2C address of
+				another chip.
+
+88pm860x consists of a large and varied group of sub-devices:
+
+Device			 Supply Names	 Description
+------			 ------------	 -----------
+88pm860x-onkey		:		: On key
+88pm860x-rtc		:		: RTC
+88pm8607		:		: Regulators
+88pm860x-backlight	:		: Backlight
+88pm860x-led		:		: Led
+88pm860x-touch		:		: Touchscreen
+
+Example:
+
+	pmic: 88pm860x@34 {
+		compatible = "marvell,88pm860x";
+		reg = <0x34>;
+		interrupts = <4>;
+		interrupt-parent = <&intc>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		marvell,88pm860x-irq-read-clr;
+		marvell,88pm860x-slave-addr = <0x11>;
+
+		regulators {
+			BUCK1 {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO1 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+		rtc {
+			marvell,88pm860x-vrtc = <1>;
+		};
+		touch {
+			marvell,88pm860x-gpadc-prebias = <1>;
+			marvell,88pm860x-gpadc-slot-cycle = <1>;
+			marvell,88pm860x-tsi-prebias = <6>;
+			marvell,88pm860x-pen-prebias = <16>;
+			marvell,88pm860x-pen-prechg = <2>;
+			marvell,88pm860x-resistor-X = <300>;
+		};
+		backlights {
+			backlight-0 {
+				marvell,88pm860x-iset = <4>;
+				marvell,88pm860x-pwm = <3>;
+			};
+			backlight-2 {
+			};
+		};
+		leds {
+			led0-red {
+				marvell,88pm860x-iset = <12>;
+			};
+			led0-green {
+				marvell,88pm860x-iset = <12>;
+			};
+			led0-blue {
+				marvell,88pm860x-iset = <12>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt
new file mode 100644
index 000000000..d2a6e835c
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/ab8500.txt
@@ -0,0 +1,280 @@
+* AB8500 Multi-Functional Device (MFD)
+
+Required parent device properties:
+- compatible             : contains "stericsson,ab8500" or "stericsson,ab8505";
+- interrupts             : contains the IRQ line for the AB8500
+- interrupt-controller   : describes the AB8500 as an Interrupt Controller (has its own domain)
+- #interrupt-cells       : should be 2, for 2-cell format
+                            - The first cell is the AB8500 local IRQ number
+                            - The second cell is used to specify optional parameters
+                              - bits[3:0] trigger type and level flags:
+                                  1 = low-to-high edge triggered
+                                  2 = high-to-low edge triggered
+                                  4 = active high level-sensitive
+                                  8 = active low level-sensitive
+
+The AB8500 consists of a large and varied group of sub-devices:
+
+Device                     IRQ Names              Supply Names   Description
+------                     ---------              ------------   -----------
+ab8500-bm                :                      :              : Battery Manager
+ab8500-btemp             :                      :              : Battery Temperature
+ab8500-charger           :                      :              : Battery Charger
+ab8500-codec             :                      :              : Audio Codec
+ab8500-fg                : 			: vddadc       : Fuel Gauge
+			 : NCONV_ACCU           :	       : Accumulate N Sample Conversion
+			 : BATT_OVV		:	       : Battery Over Voltage
+			 : LOW_BAT_F		:	       : LOW threshold battery voltage
+			 : CC_INT_CALIB		:	       : Coulomb Counter Internal Calibration
+			 : CCEOC		:	       : Coulomb Counter End of Conversion
+ab8500-btemp		 :			: vtvout       : Battery Temperature
+			 : BAT_CTRL_INDB        :              : Battery Removal Indicator
+			 : BTEMP_LOW            :              : Btemp < BtempLow, if battery temperature is lower than -10°C
+			 : BTEMP_LOW_MEDIUM     :              : BtempLow < Btemp < BtempMedium,if battery temperature is between -10 and 0°C
+			 : BTEMP_MEDIUM_HIGH    :	       : BtempMedium < Btemp < BtempHigh,if battery temperature is between 0°C and MaxTemp
+			 : BTEMP_HIGH           :              : Btemp > BtempHigh, if battery temperature is higher than MaxTemp
+ab8500-charger		 :			: vddadc       : Charger interface
+			 : MAIN_CH_UNPLUG_DET	:	       : main charger unplug detection management (not in 8505)
+			 : MAIN_CHARGE_PLUG_DET	:	       : main charger plug detection management (not in 8505)
+			 : MAIN_EXT_CH_NOT_OK	:	       : main charger not OK
+			 : MAIN_CH_TH_PROT_R	:	       : Die temp is above main charger
+			 : MAIN_CH_TH_PROT_F	:	       : Die temp is below main charger
+			 : VBUS_DET_F		:	       : VBUS falling detected
+			 : VBUS_DET_R		:	       : VBUS rising detected
+			 : USB_LINK_STATUS	:	       : USB link status has changed
+			 : USB_CH_TH_PROT_R	:	       : Die temp is above usb charger
+			 : USB_CH_TH_PROT_F	:	       : Die temp is below usb charger
+			 : USB_CHARGER_NOT_OKR	:	       : allowed USB charger not ok detection
+			 : VBUS_OVV		:	       : Overvoltage on Vbus ball detected (USB charge is stopped)
+			 : CH_WD_EXP		:	       : Charger watchdog detected
+ab8500-gpadc             : HW_CONV_END          : vddadc       : Analogue to Digital Converter
+                           SW_CONV_END          :              :
+ab8500-gpio              :                      :              : GPIO Controller (AB8500)
+ab8505-gpio              :                      :              : GPIO Controller (AB8505)
+ab8500-ponkey            : ONKEY_DBF            :              : Power-on Key
+                           ONKEY_DBR            :              :
+ab8500-pwm               :                      :              : Pulse Width Modulator
+ab8500-regulator         :                      :              : Regulators (AB8500)
+ab8505-regulator         :                      :              : Regulators (AB8505)
+ab8500-rtc               : 60S                  :              : Real Time Clock
+                         : ALARM                :              :
+ab8500-sysctrl           :                      :              : System Control
+ab8500-usb               : ID_WAKEUP_R          : vddulpivio18 : Universal Serial Bus
+                         : ID_WAKEUP_F          : v-ape        :
+                         : VBUS_DET_F           : musb_1v8     :
+                         : VBUS_DET_R           :              :
+                         : USB_LINK_STATUS      :              :
+                         : USB_ADP_PROBE_PLUG   :              :
+                         : USB_ADP_PROBE_UNPLUG :              :
+
+Required child device properties:
+- compatible             : "stericsson,ab8500-[bm|btemp|charger|fg|gpadc|gpio|ponkey|
+                                               pwm|regulator|rtc|sysctrl|usb]";
+
+  A few child devices require ADC channels from the GPADC node. Those follow the
+  standard bindings from iio/iio-bindings.txt and iio/adc/adc.txt
+
+  abx500-temp		 : io-channels "aux1" and "aux2" for measuring external
+			   temperatures.
+  ab8500-fg		 : io-channel "main_bat_v" for measuring main battery voltage,
+  ab8500-btemp		 : io-channels "btemp_ball" and "bat_ctrl" for measuring the
+			   battery voltage.
+  ab8500-charger	 : io-channels "main_charger_v", "main_charger_c", "vbus_v",
+			   "usb_charger_c" for measuring voltage and current of the
+			   different charging supplies.
+
+Optional child device properties:
+- interrupts             : contains the device IRQ(s) using the 2-cell format (see above)
+- interrupt-names        : contains names of IRQ resource in the order in which they were
+                           supplied in the interrupts property
+- <supply_name>-supply   : contains a phandle to the regulator supply node in Device Tree
+
+Non-standard child device properties:
+ - Audio CODEC:
+   - stericsson,amic[1|2]-type-single-ended : Single-ended Analoge Mic (default: differential)
+   - stericsson,amic1a-bias-vamic2          : Analoge Mic wishes to use a non-standard Vamic
+   - stericsson,amic1b-bias-vamic2          : Analoge Mic wishes to use a non-standard Vamic
+   - stericsson,amic2-bias-vamic1           : Analoge Mic wishes to use a non-standard Vamic
+   - stericsson,earpeice-cmv                : Earpeice voltage (only: 950 | 1100 | 1270 | 1580)
+
+ab8500 {
+         compatible = "stericsson,ab8500";
+         interrupts = <0 40 0x4>;
+         interrupt-controller;
+         #interrupt-cells = <2>;
+
+         ab8500-rtc {
+                 compatible = "stericsson,ab8500-rtc";
+                 interrupts = <17 0x4
+                               18 0x4>;
+                 interrupt-names = "60S", "ALARM";
+         };
+
+        ab8500-gpadc {
+                compatible = "stericsson,ab8500-gpadc";
+                interrupts = <32 0x4
+                              39 0x4>;
+                interrupt-names = "HW_CONV_END", "SW_CONV_END";
+                vddadc-supply = <&ab8500_ldo_tvout_reg>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#io-channel-cells = <1>;
+
+		/* GPADC channels */
+		bat_ctrl: channel@1 {
+			reg = <0x01>;
+		};
+		btemp_ball: channel@2 {
+			reg = <0x02>;
+		};
+		main_charger_v: channel@3 {
+			reg = <0x03>;
+		};
+		acc_detect1: channel@4 {
+			reg = <0x04>;
+		};
+		acc_detect2: channel@5 {
+			reg = <0x05>;
+		};
+		adc_aux1: channel@6 {
+			reg = <0x06>;
+		};
+		adc_aux2: channel@7 {
+			reg = <0x07>;
+		};
+		main_batt_v: channel@8 {
+			reg = <0x08>;
+		};
+		vbus_v: channel@9 {
+			reg = <0x09>;
+		};
+		main_charger_c: channel@a {
+			reg = <0x0a>;
+		};
+		usb_charger_c: channel@b {
+			reg = <0x0b>;
+		};
+		bk_bat_v: channel@c {
+			reg = <0x0c>;
+		};
+		die_temp: channel@d {
+			reg = <0x0d>;
+		};
+		usb_id: channel@e {
+			reg = <0x0e>;
+		};
+		xtal_temp: channel@12 {
+			reg = <0x12>;
+		};
+		vbat_true_meas: channel@13 {
+			reg = <0x13>;
+		};
+		bat_ctrl_and_ibat: channel@1c {
+			reg = <0x1c>;
+		};
+		vbat_meas_and_ibat: channel@1d {
+			reg = <0x1d>;
+		};
+		vbat_true_meas_and_ibat: channel@1e {
+			reg = <0x1e>;
+		};
+		bat_temp_and_ibat: channel@1f {
+			reg = <0x1f>;
+		};
+        };
+
+	ab8500_temp {
+		compatible = "stericsson,abx500-temp";
+		io-channels = <&gpadc 0x06>,
+			      <&gpadc 0x07>;
+		io-channel-name = "aux1", "aux2";
+	};
+
+	ab8500_battery: ab8500_battery {
+		stericsson,battery-type = "LIPO";
+		thermistor-on-batctrl;
+	};
+
+	ab8500_fg {
+		compatible = "stericsson,ab8500-fg";
+		battery	   = <&ab8500_battery>;
+		io-channels = <&gpadc 0x08>;
+		io-channel-name = "main_bat_v";
+	};
+
+	ab8500_btemp {
+		compatible = "stericsson,ab8500-btemp";
+		battery	   = <&ab8500_battery>;
+		io-channels = <&gpadc 0x02>,
+			      <&gpadc 0x01>;
+		io-channel-name = "btemp_ball",
+				"bat_ctrl";
+	};
+
+	ab8500_charger {
+		compatible	= "stericsson,ab8500-charger";
+		battery		= <&ab8500_battery>;
+		vddadc-supply	= <&ab8500_ldo_tvout_reg>;
+		io-channels = <&gpadc 0x03>,
+			      <&gpadc 0x0a>,
+			      <&gpadc 0x09>,
+			      <&gpadc 0x0b>;
+		io-channel-name = "main_charger_v",
+				"main_charger_c",
+				"vbus_v",
+				"usb_charger_c";
+	};
+
+        ab8500-usb {
+                compatible = "stericsson,ab8500-usb";
+                interrupts = < 90 0x4
+                               96 0x4
+                               14 0x4
+                               15 0x4
+                               79 0x4
+                               74 0x4
+                               75 0x4>;
+                interrupt-names = "ID_WAKEUP_R",
+                                  "ID_WAKEUP_F",
+                                  "VBUS_DET_F",
+                                  "VBUS_DET_R",
+                                  "USB_LINK_STATUS",
+                                  "USB_ADP_PROBE_PLUG",
+                                  "USB_ADP_PROBE_UNPLUG";
+                vddulpivio18-supply = <&ab8500_ldo_intcore_reg>;
+                v-ape-supply = <&db8500_vape_reg>;
+                musb_1v8-supply = <&db8500_vsmps2_reg>;
+        };
+
+        ab8500-ponkey {
+                compatible = "stericsson,ab8500-ponkey";
+                interrupts = <6 0x4
+                              7 0x4>;
+                interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
+        };
+
+        ab8500-sysctrl {
+                compatible = "stericsson,ab8500-sysctrl";
+        };
+
+        ab8500-pwm {
+                compatible = "stericsson,ab8500-pwm";
+        };
+
+	codec: ab8500-codec {
+		compatible = "stericsson,ab8500-codec";
+
+		stericsson,earpeice-cmv = <950>; /* Units in mV. */
+	};
+
+        ab8500-regulators {
+                compatible = "stericsson,ab8500-regulator";
+
+                ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
+                        /*
+                         * See: Documentation/devicetree/bindings/regulator/regulator.txt
+                         * for more information on regulators
+                         */
+                };
+        };
+};
diff --git a/Documentation/devicetree/bindings/mfd/ac100.txt b/Documentation/devicetree/bindings/mfd/ac100.txt
new file mode 100644
index 000000000..dff219f07
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/ac100.txt
@@ -0,0 +1,50 @@
+X-Powers AC100 Codec/RTC IC Device Tree bindings
+
+AC100 is a audio codec and RTC subsystem combo IC. The 2 parts are
+separated, including power supplies and interrupt lines, but share
+a common register address space and host interface.
+
+Required properties:
+- compatible: "x-powers,ac100"
+- reg: The I2C slave address or RSB hardware address for the chip
+- sub-nodes:
+  - codec
+    - compatible:		"x-powers,ac100-codec"
+    - interrupts:		SoC NMI / GPIO interrupt connected to the
+    				IRQ_AUDIO pin
+    - #clock-cells:		Shall be 0
+    - clock-output-names:	"4M_adda"
+
+    - see clock/clock-bindings.txt for common clock bindings
+
+  - rtc
+    - compatible:		"x-powers,ac100-rtc"
+    - clocks:			A phandle to the codec's "4M_adda" clock
+    - #clock-cells:		Shall be 1
+    - clock-output-names:	"cko1_rtc", "cko2_rtc", "cko3_rtc"
+
+    - see clock/clock-bindings.txt for common clock bindings
+
+Example:
+
+ac100: codec@e89 {
+	compatible = "x-powers,ac100";
+	reg = <0xe89>;
+
+	ac100_codec: codec {
+		compatible = "x-powers,ac100-codec";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */
+		#clock-cells = <0>;
+		clock-output-names = "4M_adda";
+	};
+
+	ac100_rtc: rtc {
+		compatible = "x-powers,ac100-rtc";
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&ac100_codec>;
+		#clock-cells = <1>;
+		clock-output-names = "cko1_rtc", "cko2_rtc", "cko3_rtc";
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/act8945a.txt b/Documentation/devicetree/bindings/mfd/act8945a.txt
new file mode 100644
index 000000000..5ca75d888
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/act8945a.txt
@@ -0,0 +1,82 @@
+Device-Tree bindings for Active-semi ACT8945A MFD driver
+
+Required properties:
+ - compatible: "active-semi,act8945a".
+ - reg: the I2C slave address for the ACT8945A chip
+
+The chip exposes two subdevices:
+ - a regulators: see ../regulator/act8945a-regulator.txt
+ - a charger: see ../power/act8945a-charger.txt
+
+Example:
+	pmic@5b {
+		compatible = "active-semi,act8945a";
+		reg = <0x5b>;
+
+		active-semi,vsel-high;
+
+		regulators {
+			vdd_1v35_reg: REG_DCDC1 {
+				regulator-name = "VDD_1V35";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+			};
+
+			vdd_1v2_reg: REG_DCDC2 {
+				regulator-name = "VDD_1V2";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+			};
+
+			vdd_3v3_reg: REG_DCDC3 {
+				regulator-name = "VDD_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_fuse_reg: REG_LDO1 {
+				regulator-name = "VDD_FUSE";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-always-on;
+			};
+
+			vdd_3v3_lp_reg: REG_LDO2 {
+				regulator-name = "VDD_3V3_LP";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_led_reg: REG_LDO3 {
+				regulator-name = "VDD_LED";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_sdhc_1v8_reg: REG_LDO4 {
+				regulator-name = "VDD_SDHC_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+		};
+
+		charger {
+			compatible = "active-semi,act8945a-charger";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>;
+			interrupt-parent = <&pioA>;
+			interrupts = <45 IRQ_TYPE_LEVEL_LOW>;
+
+			active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>;
+			active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>;
+			active-semi,input-voltage-threshold-microvolt = <6600>;
+			active-semi,precondition-timeout = <40>;
+			active-semi,total-timeout = <3>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/allwinner,sun4i-a10-ts.yaml b/Documentation/devicetree/bindings/mfd/allwinner,sun4i-a10-ts.yaml
new file mode 100644
index 000000000..f591332fc
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/allwinner,sun4i-a10-ts.yaml
@@ -0,0 +1,76 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/allwinner,sun4i-a10-ts.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A10 Resistive Touchscreen Controller Device Tree Bindings
+
+maintainers:
+  - Chen-Yu Tsai <wens@csie.org>
+  - Maxime Ripard <mripard@kernel.org>
+
+properties:
+  "#thermal-sensor-cells":
+    const: 0
+
+  compatible:
+    enum:
+      - allwinner,sun4i-a10-ts
+      - allwinner,sun5i-a13-ts
+      - allwinner,sun6i-a31-ts
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  allwinner,ts-attached:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: A touchscreen is attached to the controller
+
+  allwinner,tp-sensitive-adjust:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 15
+    default: 15
+
+    description: Sensitivity of pen down detection
+
+  allwinner,filter-type:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 3
+    default: 1
+
+    description: |
+      Select median and averaging filter. Sample used for median /
+      averaging filter:
+        0: 4/2
+        1: 5/3
+        2: 8/4
+        3: 16/8
+
+required:
+  - "#thermal-sensor-cells"
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    rtp: rtp@1c25000 {
+        compatible = "allwinner,sun4i-a10-ts";
+        reg = <0x01c25000 0x100>;
+        interrupts = <29>;
+        allwinner,ts-attached;
+        #thermal-sensor-cells = <0>;
+        /* sensitive/noisy touch panel */
+        allwinner,tp-sensitive-adjust = <0>;
+        allwinner,filter-type = <3>;
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mfd/allwinner,sun6i-a31-prcm.yaml b/Documentation/devicetree/bindings/mfd/allwinner,sun6i-a31-prcm.yaml
new file mode 100644
index 000000000..d131759cc
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/allwinner,sun6i-a31-prcm.yaml
@@ -0,0 +1,219 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/allwinner,sun6i-a31-prcm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A31 PRCM Device Tree Bindings
+
+maintainers:
+  - Chen-Yu Tsai <wens@csie.org>
+  - Maxime Ripard <mripard@kernel.org>
+
+deprecated: true
+
+properties:
+  compatible:
+    const: allwinner,sun6i-a31-prcm
+
+  reg:
+    maxItems: 1
+
+patternProperties:
+  "^.*_(clk|rst)$":
+    type: object
+
+    properties:
+      compatible:
+        enum:
+          - allwinner,sun4i-a10-mod0-clk
+          - allwinner,sun6i-a31-apb0-clk
+          - allwinner,sun6i-a31-apb0-gates-clk
+          - allwinner,sun6i-a31-ar100-clk
+          - allwinner,sun6i-a31-clock-reset
+          - fixed-factor-clock
+
+    allOf:
+      - if:
+          properties:
+            compatible:
+              contains:
+                const: allwinner,sun6i-a31-apb0-clk
+
+        then:
+          properties:
+            "#clock-cells":
+              const: 0
+
+            # Already checked in the main schema
+            compatible: true
+
+            clocks:
+              maxItems: 1
+
+            clock-output-names:
+              maxItems: 1
+
+            phandle: true
+
+          required:
+            - "#clock-cells"
+            - compatible
+            - clocks
+            - clock-output-names
+
+          additionalProperties: false
+
+      - if:
+          properties:
+            compatible:
+              contains:
+                const: allwinner,sun6i-a31-apb0-gates-clk
+
+        then:
+          properties:
+            "#clock-cells":
+              const: 1
+              description: >
+                This additional argument passed to that clock is the
+                offset of the bit controlling this particular gate in
+                the register.
+
+            # Already checked in the main schema
+            compatible: true
+
+            clocks:
+              maxItems: 1
+
+            clock-output-names:
+              minItems: 1
+              maxItems: 32
+
+            phandle: true
+
+          required:
+            - "#clock-cells"
+            - compatible
+            - clocks
+            - clock-output-names
+
+          additionalProperties: false
+
+      - if:
+          properties:
+            compatible:
+              contains:
+                const: allwinner,sun6i-a31-ar100-clk
+
+        then:
+          properties:
+            "#clock-cells":
+              const: 0
+
+            # Already checked in the main schema
+            compatible: true
+
+            clocks:
+              maxItems: 4
+              description: >
+                The parent order must match the hardware programming
+                order.
+
+            clock-output-names:
+              maxItems: 1
+
+            phandle: true
+
+          required:
+            - "#clock-cells"
+            - compatible
+            - clocks
+            - clock-output-names
+
+          additionalProperties: false
+
+      - if:
+          properties:
+            compatible:
+              contains:
+                const: allwinner,sun6i-a31-clock-reset
+
+        then:
+          properties:
+            "#reset-cells":
+              const: 1
+
+            # Already checked in the main schema
+            compatible: true
+
+            phandle: true
+
+          required:
+            - "#reset-cells"
+            - compatible
+
+          additionalProperties: false
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/sun6i-a31-ccu.h>
+
+    prcm@1f01400 {
+        compatible = "allwinner,sun6i-a31-prcm";
+        reg = <0x01f01400 0x200>;
+
+        ar100: ar100_clk {
+            compatible = "allwinner,sun6i-a31-ar100-clk";
+            #clock-cells = <0>;
+            clocks = <&rtc 0>, <&osc24M>,
+                     <&ccu CLK_PLL_PERIPH>,
+                     <&ccu CLK_PLL_PERIPH>;
+            clock-output-names = "ar100";
+        };
+
+        ahb0: ahb0_clk {
+            compatible = "fixed-factor-clock";
+            #clock-cells = <0>;
+            clock-div = <1>;
+            clock-mult = <1>;
+            clocks = <&ar100>;
+            clock-output-names = "ahb0";
+        };
+
+        apb0: apb0_clk {
+            compatible = "allwinner,sun6i-a31-apb0-clk";
+            #clock-cells = <0>;
+            clocks = <&ahb0>;
+            clock-output-names = "apb0";
+        };
+
+        apb0_gates: apb0_gates_clk {
+            compatible = "allwinner,sun6i-a31-apb0-gates-clk";
+            #clock-cells = <1>;
+            clocks = <&apb0>;
+            clock-output-names = "apb0_pio", "apb0_ir",
+                                 "apb0_timer", "apb0_p2wi",
+                                 "apb0_uart", "apb0_1wire",
+                                 "apb0_i2c";
+        };
+
+        ir_clk: ir_clk {
+            #clock-cells = <0>;
+            compatible = "allwinner,sun4i-a10-mod0-clk";
+            clocks = <&rtc 0>, <&osc24M>;
+            clock-output-names = "ir";
+        };
+
+        apb0_rst: apb0_rst {
+            compatible = "allwinner,sun6i-a31-clock-reset";
+            #reset-cells = <1>;
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mfd/allwinner,sun8i-a23-prcm.yaml b/Documentation/devicetree/bindings/mfd/allwinner,sun8i-a23-prcm.yaml
new file mode 100644
index 000000000..aa5e683b2
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/allwinner,sun8i-a23-prcm.yaml
@@ -0,0 +1,200 @@
+# SPDX-License-Identifier: GPL-2.0+
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/allwinner,sun8i-a23-prcm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A23 PRCM Device Tree Bindings
+
+maintainers:
+  - Chen-Yu Tsai <wens@csie.org>
+  - Maxime Ripard <mripard@kernel.org>
+
+deprecated: true
+
+properties:
+  compatible:
+    const: allwinner,sun8i-a23-prcm
+
+  reg:
+    maxItems: 1
+
+patternProperties:
+  "^.*(clk|rst|codec).*$":
+    type: object
+
+    properties:
+      compatible:
+        enum:
+          - fixed-factor-clock
+          - allwinner,sun8i-a23-apb0-clk
+          - allwinner,sun8i-a23-apb0-gates-clk
+          - allwinner,sun6i-a31-clock-reset
+          - allwinner,sun8i-a23-codec-analog
+
+    required:
+      - compatible
+
+    allOf:
+      - if:
+          properties:
+            compatible:
+              contains:
+                const: allwinner,sun8i-a23-apb0-clk
+
+        then:
+          properties:
+            "#clock-cells":
+              const: 0
+
+            # Already checked in the main schema
+            compatible: true
+
+            clocks:
+              maxItems: 1
+
+            clock-output-names:
+              maxItems: 1
+
+            phandle: true
+
+          required:
+            - "#clock-cells"
+            - compatible
+            - clocks
+            - clock-output-names
+
+          additionalProperties: false
+
+      - if:
+          properties:
+            compatible:
+              contains:
+                const: allwinner,sun8i-a23-apb0-gates-clk
+
+        then:
+          properties:
+            "#clock-cells":
+              const: 1
+              description: >
+                This additional argument passed to that clock is the
+                offset of the bit controlling this particular gate in
+                the register.
+
+            # Already checked in the main schema
+            compatible: true
+
+            clocks:
+              maxItems: 1
+
+            clock-output-names:
+              minItems: 1
+              maxItems: 32
+
+            phandle: true
+
+          required:
+            - "#clock-cells"
+            - compatible
+            - clocks
+            - clock-output-names
+
+          additionalProperties: false
+
+      - if:
+          properties:
+            compatible:
+              contains:
+                const: allwinner,sun6i-a31-clock-reset
+
+        then:
+          properties:
+            "#reset-cells":
+              const: 1
+
+            # Already checked in the main schema
+            compatible: true
+
+            phandle: true
+
+          required:
+            - "#reset-cells"
+            - compatible
+
+          additionalProperties: false
+
+      - if:
+          properties:
+            compatible:
+              contains:
+                const: allwinner,sun8i-a23-codec-analog
+
+        then:
+          properties:
+            # Already checked in the main schema
+            compatible: true
+
+            phandle: true
+
+          required:
+            - compatible
+
+          additionalProperties: false
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    prcm@1f01400 {
+        compatible = "allwinner,sun8i-a23-prcm";
+        reg = <0x01f01400 0x200>;
+
+        ar100: ar100_clk {
+            compatible = "fixed-factor-clock";
+            #clock-cells = <0>;
+            clock-div = <1>;
+            clock-mult = <1>;
+            clocks = <&osc24M>;
+            clock-output-names = "ar100";
+        };
+
+        ahb0: ahb0_clk {
+            compatible = "fixed-factor-clock";
+            #clock-cells = <0>;
+            clock-div = <1>;
+            clock-mult = <1>;
+            clocks = <&ar100>;
+            clock-output-names = "ahb0";
+        };
+
+        apb0: apb0_clk {
+            compatible = "allwinner,sun8i-a23-apb0-clk";
+            #clock-cells = <0>;
+            clocks = <&ahb0>;
+            clock-output-names = "apb0";
+        };
+
+        apb0_gates: apb0_gates_clk {
+            compatible = "allwinner,sun8i-a23-apb0-gates-clk";
+            #clock-cells = <1>;
+            clocks = <&apb0>;
+            clock-output-names = "apb0_pio", "apb0_timer",
+                                 "apb0_rsb", "apb0_uart",
+                                 "apb0_i2c";
+        };
+
+        apb0_rst: apb0_rst {
+            compatible = "allwinner,sun6i-a31-clock-reset";
+            #reset-cells = <1>;
+        };
+
+        codec_analog: codec-analog {
+            compatible = "allwinner,sun8i-a23-codec-analog";
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mfd/altera-a10sr.txt b/Documentation/devicetree/bindings/mfd/altera-a10sr.txt
new file mode 100644
index 000000000..a688520dd
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/altera-a10sr.txt
@@ -0,0 +1,56 @@
+* Altera Arria10 Development Kit System Resource Chip
+
+Required parent device properties:
+- compatible		: "altr,a10sr"
+- spi-max-frequency	: Maximum SPI frequency.
+- reg			: The SPI Chip Select address for the Arria10
+			  System Resource chip
+- interrupts		: The interrupt line the device is connected to.
+- interrupt-controller	: Marks the device node as an interrupt controller.
+- #interrupt-cells	: The number of cells to describe an IRQ, should be 2.
+			    The first cell is the IRQ number.
+			    The second cell is the flags, encoded as trigger
+			    masks from ../interrupt-controller/interrupts.txt.
+
+The A10SR consists of these sub-devices:
+
+Device                   Description
+------                   ----------
+a10sr_gpio               GPIO Controller
+a10sr_rst                Reset Controller
+
+Arria10 GPIO
+Required Properties:
+- compatible        : Should be "altr,a10sr-gpio"
+- gpio-controller   : Marks the device node as a GPIO Controller.
+- #gpio-cells       : Should be two.  The first cell is the pin number and
+                      the second cell is used to specify flags.
+                      See ../gpio/gpio.txt for more information.
+
+Arria10 Peripheral PHY Reset
+Required Properties:
+- compatible        : Should be "altr,a10sr-reset"
+- #reset-cells      : Should be one.
+
+Example:
+
+        resource-manager@0 {
+		compatible = "altr,a10sr";
+		reg = <0>;
+		spi-max-frequency = <100000>;
+		interrupt-parent = <&portb>;
+		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		a10sr_gpio: gpio-controller {
+			compatible = "altr,a10sr-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		a10sr_rst: reset-controller {
+			compatible = "altr,a10sr-reset";
+			#reset-cells = <1>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/as3711.txt b/Documentation/devicetree/bindings/mfd/as3711.txt
new file mode 100644
index 000000000..d98cf18c7
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/as3711.txt
@@ -0,0 +1,73 @@
+AS3711 is an I2C PMIC from Austria MicroSystems with multiple DCDC and LDO power
+supplies, a battery charger and an RTC. So far only bindings for the two stepup
+DCDC converters are defined. Other DCDC and LDO supplies are configured, using
+standard regulator properties, they must belong to a sub-node, called
+"regulators" and be called "sd1" to "sd4" and "ldo1" to "ldo8." Stepup converter
+configuration should be placed in a subnode, called "backlight."
+
+Compulsory properties:
+- compatible		: must be "ams,as3711"
+- reg			: specifies the I2C address
+
+To use the SU1 converter as a backlight source the following two properties must
+be provided:
+- su1-dev		: framebuffer phandle
+- su1-max-uA		: maximum current
+
+To use the SU2 converter as a backlight source the following two properties must
+be provided:
+- su2-dev		: framebuffer phandle
+- su1-max-uA		: maximum current
+
+Additionally one of these properties must be provided to select the type of
+feedback used:
+- su2-feedback-voltage	: voltage feedback is used
+- su2-feedback-curr1	: CURR1 input used for current feedback
+- su2-feedback-curr2	: CURR2 input used for current feedback
+- su2-feedback-curr3	: CURR3 input used for current feedback
+- su2-feedback-curr-auto: automatic current feedback selection
+
+and one of these to select the over-voltage protection pin
+- su2-fbprot-lx-sd4	: LX_SD4 is used for over-voltage protection
+- su2-fbprot-gpio2	: GPIO2 is used for over-voltage protection
+- su2-fbprot-gpio3	: GPIO3 is used for over-voltage protection
+- su2-fbprot-gpio4	: GPIO4 is used for over-voltage protection
+
+If "su2-feedback-curr-auto" is selected, one or more of the following properties
+have to be specified:
+- su2-auto-curr1	: use CURR1 input for current feedback
+- su2-auto-curr2	: use CURR2 input for current feedback
+- su2-auto-curr3	: use CURR3 input for current feedback
+
+Example:
+
+as3711@40 {
+	compatible = "ams,as3711";
+	reg = <0x40>;
+
+	regulators {
+		sd4 {
+			regulator-name = "1.215V";
+			regulator-min-microvolt = <1215000>;
+			regulator-max-microvolt = <1235000>;
+		};
+		ldo2 {
+			regulator-name = "2.8V CPU";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+	};
+
+	backlight {
+		compatible = "ams,as3711-bl";
+		su2-dev = <&lcdc>;
+		su2-max-uA = <36000>;
+		su2-feedback-curr-auto;
+		su2-fbprot-gpio4;
+		su2-auto-curr1;
+		su2-auto-curr2;
+		su2-auto-curr3;
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/as3722.txt b/Documentation/devicetree/bindings/mfd/as3722.txt
new file mode 100644
index 000000000..2a665741d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/as3722.txt
@@ -0,0 +1,214 @@
+* ams AS3722 Power management IC.
+
+Required properties:
+-------------------
+- compatible: Must be "ams,as3722".
+- reg: I2C device address.
+- interrupt-controller: AS3722 has internal interrupt controller which takes the
+  interrupt request from internal sub-blocks like RTC, regulators, GPIOs as well
+  as external input.
+- #interrupt-cells: Should be set to 2 for IRQ number and flags.
+  The first cell is the IRQ number. IRQ numbers for different interrupt source
+  of AS3722 are defined at dt-bindings/mfd/as3722.h
+  The second cell is the flags, encoded as the trigger masks from binding document
+	interrupts.txt, using dt-bindings/irq.
+
+Optional properties:
+--------------------
+- ams,enable-internal-int-pullup: Boolean property, to enable internal pullup on
+	interrupt pin. Missing this will disable internal pullup on INT pin.
+- ams,enable-internal-i2c-pullup: Boolean property, to enable internal pullup on
+	i2c scl/sda pins. Missing this will disable internal pullup on i2c
+	scl/sda lines.
+- ams,enable-ac-ok-power-on: Boolean property, to enable exit out of power off
+	mode with AC_OK pin (pin enabled in power off mode).
+
+Optional submodule and their properties:
+=======================================
+
+Pinmux and GPIO:
+===============
+Device has 8 GPIO pins which can be configured as GPIO as well as the special IO
+functions.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Following are properties which is needed if GPIO and pinmux functionality
+is required:
+    Required properties:
+    -------------------
+	- gpio-controller: Marks the device node as a GPIO controller.
+	- #gpio-cells: Number of GPIO cells. Refer to binding document
+			gpio/gpio.txt
+
+    Optional properties:
+    --------------------
+	Following properties are require if pin control setting is required
+	at boot.
+	- pinctrl-names: A pinctrl state named "default" be defined, using the
+		bindings in pinctrl/pinctrl-bindings.txt.
+	- pinctrl[0...n]: Properties to contain the phandle that refer to
+		different nodes of pin control settings. These nodes represents
+		the pin control setting of state 0 to state n. Each of these
+		nodes contains different subnodes to represents some desired
+		configuration for a list of pins. This configuration can
+		include the mux function to select on those pin(s), and
+		various pin configuration parameters, such as pull-up,
+		open drain.
+
+		Each subnode have following properties:
+		Required properties:
+		    - pins: List of pins. Valid values of pins properties are:
+				gpio0, gpio1, gpio2, gpio3, gpio4, gpio5,
+				gpio6, gpio7
+
+		Optional properties:
+			function, bias-disable, bias-pull-up, bias-pull-down,
+			bias-high-impedance, drive-open-drain.
+
+			Valid values for function properties are:
+				gpio, interrupt-out, gpio-in-interrupt,
+				vsup-vbat-low-undebounce-out,
+				vsup-vbat-low-debounce-out,
+				voltage-in-standby, oc-pg-sd0, oc-pg-sd6,
+				powergood-out, pwm-in, pwm-out, clk32k-out,
+				watchdog-in, soft-reset-in
+
+Regulators:
+===========
+Device has multiple DCDC and LDOs. The node "regulators" is require if regulator
+functionality is needed.
+
+Following are properties of regulator subnode.
+
+    Optional properties:
+    -------------------
+	The input supply of regulators are the optional properties on the
+	regulator node. The input supply of these regulators are provided
+	through following properties:
+		vsup-sd2-supply: Input supply for SD2.
+		vsup-sd3-supply: Input supply for SD3.
+		vsup-sd4-supply: Input supply for SD4.
+		vsup-sd5-supply: Input supply for SD5.
+		vin-ldo0-supply: Input supply for LDO0.
+		vin-ldo1-6-supply: Input supply for LDO1 and LDO6.
+		vin-ldo2-5-7-supply: Input supply for LDO2, LDO5 and LDO7.
+		vin-ldo3-4-supply: Input supply for LDO3 and LDO4.
+		vin-ldo9-10-supply: Input supply for LDO9 and LDO10.
+		vin-ldo11-supply: Input supply for LDO11.
+
+    Optional sub nodes for regulators:
+    ---------------------------------
+	The subnodes name is the name of regulator and it must be one of:
+	sd[0-6], ldo[0-7], ldo[9-11]
+
+	Each sub-node should contain the constraints and initialization
+	information for that regulator. See regulator.txt for a description
+	of standard properties for these sub-nodes.
+	Additional optional custom properties  are listed below.
+		ams,ext-control: External control of the rail. The option of
+			this properties will tell which external input is
+			controlling this rail. Valid values are 0, 1, 2 ad 3.
+			0: There is no external control of this rail.
+			1: Rail is controlled by ENABLE1 input pin.
+			2: Rail is controlled by ENABLE2 input pin.
+			3: Rail is controlled by ENABLE3 input pin.
+			Missing this property on DT will be assume as no
+			external control. The external control pin macros
+			are defined @dt-bindings/mfd/as3722.h
+
+		ams,enable-tracking: Enable tracking with SD1, only supported
+			by LDO3.
+
+Power-off:
+=========
+AS3722 supports the system power off by turning off all its rails.
+The device node should have the following properties to enable this
+functionality
+ams,system-power-controller: Boolean, to enable the power off functionality
+        through this device.
+
+Example:
+--------
+#include <dt-bindings/mfd/as3722.h>
+...
+ams3722 {
+	compatible = "ams,as3722";
+	reg = <0x48>;
+
+	ams,system-power-controller;
+
+	interrupt-parent = <&intc>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+
+	gpio-controller;
+	#gpio-cells = <2>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&as3722_default>;
+
+	as3722_default: pinmux {
+			gpio0 {
+				pins = "gpio0";
+				function = "gpio";
+				bias-pull-down;
+			};
+
+			gpio1_2_4_7 {
+				pins = "gpio1", "gpio2", "gpio4", "gpio7";
+				function = "gpio";
+				bias-pull-up;
+			};
+
+			gpio5 {
+				pins = "gpio5";
+				function = "clk32k_out";
+			};
+	}
+
+	regulators {
+			vsup-sd2-supply = <...>;
+			...
+
+			sd0 {
+				regulator-name = "vdd_cpu";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				ams,ext-control = <2>;
+			};
+
+			sd1 {
+				regulator-name = "vdd_core";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				ams,ext-control = <1>;
+			};
+
+			sd2 {
+				regulator-name = "vddio_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+			};
+
+			sd4 {
+				regulator-name = "avdd-hdmi-pex";
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1050000>;
+				regulator-always-on;
+			};
+
+			sd5 {
+				regulator-name = "vdd-1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+			....
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/aspeed-gfx.txt b/Documentation/devicetree/bindings/mfd/aspeed-gfx.txt
new file mode 100644
index 000000000..aea5370ef
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/aspeed-gfx.txt
@@ -0,0 +1,17 @@
+* Device tree bindings for Aspeed SoC Display Controller (GFX)
+
+The Aspeed SoC Display Controller primarily does as its name suggests, but also
+participates in pinmux requests on the g5 SoCs. It is therefore considered a
+syscon device.
+
+Required properties:
+- compatible:		"aspeed,ast2500-gfx", "syscon"
+- reg:			contains offset/length value of the GFX memory
+			region.
+
+Example:
+
+gfx: display@1e6e6000 {
+	compatible = "aspeed,ast2500-gfx", "syscon";
+	reg = <0x1e6e6000 0x1000>;
+};
diff --git a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt
new file mode 100644
index 000000000..a92acf1dd
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt
@@ -0,0 +1,201 @@
+======================================================================
+Device tree bindings for the Aspeed Low Pin Count (LPC) Bus Controller
+======================================================================
+
+The LPC bus is a means to bridge a host CPU to a number of low-bandwidth
+peripheral devices, replacing the use of the ISA bus in the age of PCI[0]. The
+primary use case of the Aspeed LPC controller is as a slave on the bus
+(typically in a Baseboard Management Controller SoC), but under certain
+conditions it can also take the role of bus master.
+
+The LPC controller is represented as a multi-function device to account for the
+mix of functionality it provides. The principle split is between the register
+layout at the start of the I/O space which is, to quote the Aspeed datasheet,
+"basically compatible with the [LPC registers from the] popular BMC controller
+H8S/2168[1]", and everything else, where everything else is an eclectic
+collection of functions with a esoteric register layout. "Everything else",
+here labeled the "host" portion of the controller, includes, but is not limited
+to:
+
+* An IPMI Block Transfer[2] Controller
+
+* An LPC Host Controller: Manages LPC functions such as host vs slave mode, the
+  physical properties of some LPC pins, configuration of serial IRQs, and
+  APB-to-LPC bridging amonst other functions.
+
+* An LPC Host Interface Controller: Manages functions exposed to the host such
+  as LPC firmware hub cycles, configuration of the LPC-to-AHB mapping, UART
+  management and bus snoop configuration.
+
+* A set of SuperIO[3] scratch registers: Enables implementation of e.g. custom
+  hardware management protocols for handover between the host and baseboard
+  management controller.
+
+Additionally the state of the LPC controller influences the pinmux
+configuration, therefore the host portion of the controller is exposed as a
+syscon as a means to arbitrate access.
+
+[0] http://www.intel.com/design/chipsets/industry/25128901.pdf
+[1] https://www.renesas.com/en-sg/doc/products/mpumcu/001/rej09b0078_h8s2168.pdf?key=7c88837454702128622bee53acbda8f4
+[2] https://www.intel.com/content/dam/www/public/us/en/documents/product-briefs/ipmi-second-gen-interface-spec-v2-rev1-1.pdf
+[3] https://en.wikipedia.org/wiki/Super_I/O
+
+Required properties
+===================
+
+- compatible:	One of:
+		"aspeed,ast2400-lpc", "simple-mfd"
+		"aspeed,ast2500-lpc", "simple-mfd"
+
+- reg:		contains the physical address and length values of the Aspeed
+                LPC memory region.
+
+- #address-cells: <1>
+- #size-cells:	<1>
+- ranges: 	Maps 0 to the physical address and length of the LPC memory
+                region
+
+Required LPC Child nodes
+========================
+
+BMC Node
+--------
+
+- compatible:	One of:
+		"aspeed,ast2400-lpc-bmc"
+		"aspeed,ast2500-lpc-bmc"
+
+- reg:		contains the physical address and length values of the
+                H8S/2168-compatible LPC controller memory region
+
+Host Node
+---------
+
+- compatible:   One of:
+		"aspeed,ast2400-lpc-host", "simple-mfd", "syscon"
+		"aspeed,ast2500-lpc-host", "simple-mfd", "syscon"
+
+- reg:		contains the address and length values of the host-related
+                register space for the Aspeed LPC controller
+
+- #address-cells: <1>
+- #size-cells:	<1>
+- ranges: 	Maps 0 to the address and length of the host-related LPC memory
+                region
+
+Example:
+
+lpc: lpc@1e789000 {
+	compatible = "aspeed,ast2500-lpc", "simple-mfd";
+	reg = <0x1e789000 0x1000>;
+
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges = <0x0 0x1e789000 0x1000>;
+
+	lpc_bmc: lpc-bmc@0 {
+		compatible = "aspeed,ast2500-lpc-bmc";
+		reg = <0x0 0x80>;
+	};
+
+	lpc_host: lpc-host@80 {
+		compatible = "aspeed,ast2500-lpc-host", "simple-mfd", "syscon";
+		reg = <0x80 0x1e0>;
+		reg-io-width = <4>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x80 0x1e0>;
+	};
+};
+
+BMC Node Children
+==================
+
+
+Host Node Children
+==================
+
+LPC Host Interface Controller
+-------------------
+
+The LPC Host Interface Controller manages functions exposed to the host such as
+LPC firmware hub cycles, configuration of the LPC-to-AHB mapping, UART
+management and bus snoop configuration.
+
+Required properties:
+
+- compatible:	One of:
+		"aspeed,ast2400-lpc-ctrl";
+		"aspeed,ast2500-lpc-ctrl";
+
+- reg:		contains offset/length values of the host interface controller
+		memory regions
+
+- clocks:	contains a phandle to the syscon node describing the clocks.
+		There should then be one cell representing the clock to use
+
+Optional properties:
+
+- memory-region: A phandle to a reserved_memory region to be used for the LPC
+		to AHB mapping
+
+- flash:	A phandle to the SPI flash controller containing the flash to
+		be exposed over the LPC to AHB mapping
+
+Example:
+
+lpc-host@80 {
+	lpc_ctrl: lpc-ctrl@0 {
+		compatible = "aspeed,ast2500-lpc-ctrl";
+		reg = <0x0 0x80>;
+		clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+		memory-region = <&flash_memory>;
+		flash = <&spi>;
+	};
+};
+
+LPC Host Controller
+-------------------
+
+The Aspeed LPC Host Controller configures the Low Pin Count (LPC) bus behaviour
+between the host and the baseboard management controller. The registers exist
+in the "host" portion of the Aspeed LPC controller, which must be the parent of
+the LPC host controller node.
+
+Required properties:
+
+- compatible:	One of:
+		"aspeed,ast2400-lhc";
+		"aspeed,ast2500-lhc";
+
+- reg:		contains offset/length values of the LHC memory regions. In the
+		AST2400 and AST2500 there are two regions.
+
+Example:
+
+lhc: lhc@20 {
+	compatible = "aspeed,ast2500-lhc";
+	reg = <0x20 0x24 0x48 0x8>;
+};
+
+LPC reset control
+-----------------
+
+The UARTs present in the ASPEED SoC can have their resets tied to the reset
+state of the LPC bus. Some systems may chose to modify this configuration.
+
+Required properties:
+
+ - compatible:		"aspeed,ast2500-lpc-reset" or
+			"aspeed,ast2400-lpc-reset"
+ - reg:			offset and length of the IP in the LHC memory region
+ - #reset-controller	indicates the number of reset cells expected
+
+Example:
+
+lpc_reset: reset-controller@18 {
+        compatible = "aspeed,ast2500-lpc-reset";
+        reg = <0x18 0x4>;
+        #reset-cells = <1>;
+};
diff --git a/Documentation/devicetree/bindings/mfd/aspeed-scu.txt b/Documentation/devicetree/bindings/mfd/aspeed-scu.txt
new file mode 100644
index 000000000..4d92c0bb6
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/aspeed-scu.txt
@@ -0,0 +1,22 @@
+The Aspeed System Control Unit manages the global behaviour of the SoC,
+configuring elements such as clocks, pinmux, and reset.
+
+Required properties:
+- compatible:	One of:
+		"aspeed,ast2400-scu", "syscon", "simple-mfd"
+		"aspeed,ast2500-scu", "syscon", "simple-mfd"
+
+- reg:		contains the offset and length of the SCU memory region
+- #clock-cells: should be set to <1> - the system controller is also a
+	clock provider
+- #reset-cells: should be set to <1> - the system controller is also a
+	reset line provider
+
+Example:
+
+syscon: syscon@1e6e2000 {
+	compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd";
+	reg = <0x1e6e2000 0x1a8>;
+	#clock-cells = <1>;
+	#reset-cells = <1>;
+};
diff --git a/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
new file mode 100644
index 000000000..692300117
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
@@ -0,0 +1,63 @@
+* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit)
+
+The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C
+controller and an USART. Only one function can be used at a time and is chosen
+at boot time according to the device tree.
+
+Required properties:
+- compatible:		Should be "atmel,sama5d2-flexcom"
+- reg:			Should be the offset/length value for Flexcom dedicated
+			I/O registers (without USART, TWI or SPI registers).
+- clocks:		Should be the Flexcom peripheral clock from PMC.
+- #address-cells:	Should be <1>
+- #size-cells:		Should be <1>
+- ranges:		Should be one range for the full I/O register region
+			(including USART, TWI and SPI registers).
+- atmel,flexcom-mode:	Should be one of the following values:
+			- <1> for USART
+			- <2> for SPI
+			- <3> for I2C
+
+Required child:
+A single available child device of type matching the "atmel,flexcom-mode"
+property.
+
+The phandle provided by the clocks property of the child is the same as one for
+the Flexcom parent.
+
+For other properties, please refer to the documentations of the respective
+device:
+- ../serial/atmel-usart.txt
+- ../spi/spi_atmel.txt
+- ../i2c/i2c-at91.txt
+
+Example:
+
+flexcom@f8034000 {
+	compatible = "atmel,sama5d2-flexcom";
+	reg = <0xf8034000 0x200>;
+	clocks = <&flx0_clk>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges = <0x0 0xf8034000 0x800>;
+	atmel,flexcom-mode = <2>;
+
+	spi@400 {
+		compatible = "atmel,at91rm9200-spi";
+		reg = <0x400 0x200>;
+		interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&flx0_clk>;
+		clock-names = "spi_clk";
+		atmel,fifo-size = <32>;
+
+		mtd_dataflash@0 {
+			compatible = "atmel,at25f512b";
+			reg = <0>;
+			spi-max-frequency = <20000000>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/atmel-gpbr.txt b/Documentation/devicetree/bindings/mfd/atmel-gpbr.txt
new file mode 100644
index 000000000..e8c525569
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/atmel-gpbr.txt
@@ -0,0 +1,17 @@
+* Device tree bindings for Atmel GPBR (General Purpose Backup Registers)
+
+The GPBR are a set of battery-backed registers.
+
+Required properties:
+- compatible:		Should be one of the following:
+			"atmel,at91sam9260-gpbr", "syscon"
+			"microchip,sam9x60-gpbr", "syscon"
+- reg:			contains offset/length value of the GPBR memory
+			region.
+
+Example:
+
+gpbr: gpbr@fffffd50 {
+	compatible = "atmel,at91sam9260-gpbr", "syscon";
+	reg = <0xfffffd50 0x10>;
+};
diff --git a/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt
new file mode 100644
index 000000000..5f8880cc7
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt
@@ -0,0 +1,55 @@
+Device-Tree bindings for Atmel's HLCDC (High LCD Controller) MFD driver
+
+Required properties:
+ - compatible: value should be one of the following:
+   "atmel,at91sam9n12-hlcdc"
+   "atmel,at91sam9x5-hlcdc"
+   "atmel,sama5d2-hlcdc"
+   "atmel,sama5d3-hlcdc"
+   "atmel,sama5d4-hlcdc"
+   "microchip,sam9x60-hlcdc"
+ - reg: base address and size of the HLCDC device registers.
+ - clock-names: the name of the 3 clocks requested by the HLCDC device.
+   Should contain "periph_clk", "sys_clk" and "slow_clk".
+ - clocks: should contain the 3 clocks requested by the HLCDC device.
+ - interrupts: should contain the description of the HLCDC interrupt line
+
+The HLCDC IP exposes two subdevices:
+ - a PWM chip: see ../pwm/atmel-hlcdc-pwm.txt
+ - a Display Controller: see ../display/atmel/hlcdc-dc.txt
+
+Example:
+
+	hlcdc: hlcdc@f0030000 {
+		compatible = "atmel,sama5d3-hlcdc";
+		reg = <0xf0030000 0x2000>;
+		clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>;
+		clock-names = "periph_clk","sys_clk", "slow_clk";
+		interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>;
+
+		hlcdc-display-controller {
+			compatible = "atmel,hlcdc-display-controller";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+
+				hlcdc_panel_output: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&panel_input>;
+				};
+			};
+		};
+
+		hlcdc_pwm: hlcdc-pwm {
+			compatible = "atmel,hlcdc-pwm";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_lcd_pwm>;
+			#pwm-cells = <3>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/atmel-matrix.txt b/Documentation/devicetree/bindings/mfd/atmel-matrix.txt
new file mode 100644
index 000000000..89d05c64f
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/atmel-matrix.txt
@@ -0,0 +1,25 @@
+* Device tree bindings for Atmel Bus Matrix
+
+The Bus Matrix registers are used to configure Atmel SoCs internal bus
+behavior (master/slave priorities, undefined burst length type, ...)
+
+Required properties:
+- compatible:		Should be one of the following
+			"atmel,at91sam9260-matrix", "syscon"
+			"atmel,at91sam9261-matrix", "syscon"
+			"atmel,at91sam9263-matrix", "syscon"
+			"atmel,at91sam9rl-matrix", "syscon"
+			"atmel,at91sam9g45-matrix", "syscon"
+			"atmel,at91sam9n12-matrix", "syscon"
+			"atmel,at91sam9x5-matrix", "syscon"
+			"atmel,sama5d3-matrix", "syscon"
+			"microchip,sam9x60-matrix", "syscon"
+- reg:			Contains offset/length value of the Bus Matrix
+			memory region.
+
+Example:
+
+matrix: matrix@ffffec00 {
+	compatible = "atmel,sama5d3-matrix", "syscon";
+	reg = <0xffffec00 0x200>;
+};
diff --git a/Documentation/devicetree/bindings/mfd/atmel-smc.txt b/Documentation/devicetree/bindings/mfd/atmel-smc.txt
new file mode 100644
index 000000000..5696d9fcb
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/atmel-smc.txt
@@ -0,0 +1,21 @@
+* Device tree bindings for Atmel SMC (Static Memory Controller)
+
+The SMC registers are used to configure Atmel EBI (External Bus Interface)
+to interface with standard memory devices (NAND, NOR, SRAM or specialized
+devices like FPGAs).
+
+Required properties:
+- compatible:		Should be one of the following
+			"atmel,at91sam9260-smc", "syscon"
+			"atmel,sama5d3-smc", "syscon"
+			"atmel,sama5d2-smc", "syscon"
+			"microchip,sam9x60-smc", "syscon"
+- reg:			Contains offset/length value of the SMC memory
+			region.
+
+Example:
+
+smc: smc@ffffc000 {
+	compatible = "atmel,sama5d3-smc", "syscon";
+	reg = <0xffffc000 0x1000>;
+};
diff --git a/Documentation/devicetree/bindings/mfd/atmel-usart.txt b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
new file mode 100644
index 000000000..a09133066
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
@@ -0,0 +1,98 @@
+* Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART)
+
+Required properties for USART:
+- compatible: Should be one of the following:
+	- "atmel,at91rm9200-usart"
+	- "atmel,at91sam9260-usart"
+	- "microchip,sam9x60-usart"
+	- "atmel,at91rm9200-dbgu", "atmel,at91rm9200-usart"
+	- "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart"
+	- "microchip,sam9x60-dbgu", "microchip,sam9x60-usart"
+- reg: Should contain registers location and length
+- interrupts: Should contain interrupt
+- clock-names: tuple listing input clock names.
+	Required elements: "usart"
+- clocks: phandles to input clocks.
+
+Required properties for USART in SPI mode:
+- #size-cells      : Must be <0>
+- #address-cells   : Must be <1>
+- cs-gpios: chipselects (internal cs not supported)
+- atmel,usart-mode : Must be <AT91_USART_MODE_SPI> (found in dt-bindings/mfd/at91-usart.h)
+
+Optional properties in serial and SPI mode:
+- dma bindings for dma transfer:
+	- dmas: DMA specifier, consisting of a phandle to DMA controller node,
+		memory peripheral interface and USART DMA channel ID, FIFO configuration.
+		The order of DMA channels is fixed. The first DMA channel must be TX
+		associated channel and the second one must be RX associated channel.
+		Refer to dma.txt and atmel-dma.txt for details.
+	- dma-names: "tx" for TX channel.
+		     "rx" for RX channel.
+		     The order of dma-names is also fixed. The first name must be "tx"
+		     and the second one must be "rx" as in the examples below.
+
+Optional properties in serial mode:
+- atmel,use-dma-rx: use of PDC or DMA for receiving data
+- atmel,use-dma-tx: use of PDC or DMA for transmitting data
+- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively.
+  It will use specified PIO instead of the peripheral function pin for the USART feature.
+  If unsure, don't specify this property.
+- atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO
+  capable USARTs.
+- rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt
+
+<chip> compatible description:
+- at91rm9200:  legacy USART support
+- at91sam9260: generic USART implementation for SAM9 SoCs
+
+Example:
+- use PDC:
+	usart0: serial@fff8c000 {
+		compatible = "atmel,at91sam9260-usart";
+		reg = <0xfff8c000 0x4000>;
+		interrupts = <7>;
+		clocks = <&usart0_clk>;
+		clock-names = "usart";
+		atmel,use-dma-rx;
+		atmel,use-dma-tx;
+		rts-gpios = <&pioD 15 GPIO_ACTIVE_LOW>;
+		cts-gpios = <&pioD 16 GPIO_ACTIVE_LOW>;
+		dtr-gpios = <&pioD 17 GPIO_ACTIVE_LOW>;
+		dsr-gpios = <&pioD 18 GPIO_ACTIVE_LOW>;
+		dcd-gpios = <&pioD 20 GPIO_ACTIVE_LOW>;
+		rng-gpios = <&pioD 19 GPIO_ACTIVE_LOW>;
+	};
+
+- use DMA:
+	usart0: serial@f001c000 {
+		compatible = "atmel,at91sam9260-usart";
+		reg = <0xf001c000 0x100>;
+		interrupts = <12 4 5>;
+		clocks = <&usart0_clk>;
+		clock-names = "usart";
+		atmel,use-dma-rx;
+		atmel,use-dma-tx;
+		dmas = <&dma0 2 0x3>,
+		       <&dma0 2 0x204>;
+		dma-names = "tx", "rx";
+		atmel,fifo-size = <32>;
+	};
+
+- SPI mode:
+	#include <dt-bindings/mfd/at91-usart.h>
+
+	spi0: spi@f001c000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "atmel,at91rm9200-usart", "atmel,at91sam9260-usart";
+		atmel,usart-mode = <AT91_USART_MODE_SPI>;
+		reg = <0xf001c000 0x100>;
+		interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>;
+		clocks = <&usart0_clk>;
+		clock-names = "usart";
+		dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>,
+		       <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+		dma-names = "tx", "rx";
+		cs-gpios = <&pioB 3 0>;
+	};
diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
new file mode 100644
index 000000000..4991a6415
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
@@ -0,0 +1,272 @@
+AXP family PMIC device tree bindings
+
+The axp20x family current members :
+axp152 (X-Powers)
+axp202 (X-Powers)
+axp209 (X-Powers)
+axp221 (X-Powers)
+axp223 (X-Powers)
+axp803 (X-Powers)
+axp806 (X-Powers)
+axp809 (X-Powers)
+axp813 (X-Powers)
+
+The AXP813 is 2 chips packaged into 1. The 2 chips do not share anything
+other than the packaging. Pins are routed separately. As such they should
+be treated as separate entities. The other half is an AC100 RTC/codec
+combo chip. Please see ./ac100.txt for its bindings.
+
+Required properties:
+- compatible: should be one of:
+    * "x-powers,axp152"
+    * "x-powers,axp202"
+    * "x-powers,axp209"
+    * "x-powers,axp221"
+    * "x-powers,axp223"
+    * "x-powers,axp803"
+    * "x-powers,axp806"
+    * "x-powers,axp805", "x-powers,axp806"
+    * "x-powers,axp809"
+    * "x-powers,axp813"
+- reg: The I2C slave address or RSB hardware address for the AXP chip
+- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
+- interrupt-controller: The PMIC has its own internal IRQs
+- #interrupt-cells: Should be set to 1
+
+Supported common regulator properties, see ../regulator/regulator.txt for
+more information:
+- regulator-ramp-delay: sets the ramp up delay in uV/us
+			AXP20x/DCDC2: 1600, 800
+			AXP20x/LDO3:  1600, 800
+- regulator-soft-start:	enable the output at the lowest possible voltage and
+			only then set the desired voltage
+			AXP20x/LDO3: software-based implementation
+
+Optional properties:
+- x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
+		      AXP152/20X: range:  750-1875, Default: 1.5 MHz
+		      AXP22X/8XX: range: 1800-4050, Default: 3   MHz
+
+- x-powers,drive-vbus-en: boolean, set this when the N_VBUSEN pin is
+			  used as an output pin to control an external
+			  regulator to drive the OTG VBus, rather then
+			  as an input pin which signals whether the
+			  board is driving OTG VBus or not.
+			  (axp221 / axp223 / axp803/ axp813 only)
+
+- x-powers,self-working-mode and
+  x-powers,master-mode: Boolean (axp806 only). Set either of these when the
+			PMIC is wired for self-working mode or master mode.
+			If neither is set then slave mode is assumed.
+			This corresponds to how the MODESET pin is wired.
+
+- <input>-supply: a phandle to the regulator supply node. May be omitted if
+		  inputs are unregulated, such as using the IPSOUT output
+		  from the PMIC.
+
+- regulators: A node that houses a sub-node for each regulator. Regulators
+	      not used but preferred to be managed by the OS should be
+	      listed as well.
+	      See Documentation/devicetree/bindings/regulator/regulator.txt
+	      for more information on standard regulator bindings.
+
+Optional properties for DCDC regulators:
+- x-powers,dcdc-workmode: 1 for PWM mode, 0 for AUTO (PWM/PFM) mode
+			  Default: Current hardware setting
+			  The DCDC regulators work in a mixed PWM/PFM mode,
+			  using PFM under light loads and switching to PWM
+			  for heavier loads. Forcing PWM mode trades efficiency
+			  under light loads for lower output noise. This
+			  probably makes sense for HiFi audio related
+			  applications that aren't battery constrained.
+
+AXP202/AXP209 regulators, type, and corresponding input supply names:
+
+Regulator	  Type		  Supply Name		  Notes
+---------	  ----		  -----------		  -----
+DCDC2		: DC-DC buck	: vin2-supply
+DCDC3		: DC-DC	buck	: vin3-supply
+LDO1		: LDO		: acin-supply		: always on
+LDO2		: LDO		: ldo24in-supply	: shared supply
+LDO3		: LDO		: ldo3in-supply
+LDO4		: LDO		: ldo24in-supply	: shared supply
+LDO5		: LDO		: ldo5in-supply
+
+AXP221/AXP223 regulators, type, and corresponding input supply names:
+
+Regulator	  Type		  Supply Name		  Notes
+---------	  ----		  -----------		  -----
+DCDC1		: DC-DC buck	: vin1-supply
+DCDC2		: DC-DC buck	: vin2-supply
+DCDC3		: DC-DC	buck	: vin3-supply
+DCDC4		: DC-DC	buck	: vin4-supply
+DCDC5		: DC-DC	buck	: vin5-supply
+DC1SW		: On/Off Switch	:			: DCDC1 secondary output
+DC5LDO		: LDO		:			: input from DCDC5
+ALDO1		: LDO		: aldoin-supply		: shared supply
+ALDO2		: LDO		: aldoin-supply		: shared supply
+ALDO3		: LDO		: aldoin-supply		: shared supply
+DLDO1		: LDO		: dldoin-supply		: shared supply
+DLDO2		: LDO		: dldoin-supply		: shared supply
+DLDO3		: LDO		: dldoin-supply		: shared supply
+DLDO4		: LDO		: dldoin-supply		: shared supply
+ELDO1		: LDO		: eldoin-supply		: shared supply
+ELDO2		: LDO		: eldoin-supply		: shared supply
+ELDO3		: LDO		: eldoin-supply		: shared supply
+LDO_IO0		: LDO		: ips-supply		: GPIO 0
+LDO_IO1		: LDO		: ips-supply		: GPIO 1
+RTC_LDO		: LDO		: ips-supply		: always on
+DRIVEVBUS	: Enable output	: drivevbus-supply	: external regulator
+
+AXP803 regulators, type, and corresponding input supply names:
+
+Regulator	  Type		  Supply Name		  Notes
+---------	  ----		  -----------		  -----
+DCDC1		: DC-DC buck	: vin1-supply
+DCDC2		: DC-DC buck	: vin2-supply		: poly-phase capable
+DCDC3		: DC-DC	buck	: vin3-supply		: poly-phase capable
+DCDC4		: DC-DC	buck	: vin4-supply
+DCDC5		: DC-DC	buck	: vin5-supply		: poly-phase capable
+DCDC6		: DC-DC	buck	: vin6-supply		: poly-phase capable
+DC1SW		: On/Off Switch	:			: DCDC1 secondary output
+ALDO1		: LDO		: aldoin-supply		: shared supply
+ALDO2		: LDO		: aldoin-supply		: shared supply
+ALDO3		: LDO		: aldoin-supply		: shared supply
+DLDO1		: LDO		: dldoin-supply		: shared supply
+DLDO2		: LDO		: dldoin-supply		: shared supply
+DLDO3		: LDO		: dldoin-supply		: shared supply
+DLDO4		: LDO		: dldoin-supply		: shared supply
+ELDO1		: LDO		: eldoin-supply		: shared supply
+ELDO2		: LDO		: eldoin-supply		: shared supply
+ELDO3		: LDO		: eldoin-supply		: shared supply
+FLDO1		: LDO		: fldoin-supply		: shared supply
+FLDO2		: LDO		: fldoin-supply		: shared supply
+LDO_IO0		: LDO		: ips-supply		: GPIO 0
+LDO_IO1		: LDO		: ips-supply		: GPIO 1
+RTC_LDO		: LDO		: ips-supply		: always on
+DRIVEVBUS	: Enable output	: drivevbus-supply	: external regulator
+
+AXP806 regulators, type, and corresponding input supply names:
+
+Regulator	  Type		  Supply Name		  Notes
+---------	  ----		  -----------		  -----
+DCDCA		: DC-DC buck	: vina-supply		: poly-phase capable
+DCDCB		: DC-DC buck	: vinb-supply		: poly-phase capable
+DCDCC		: DC-DC	buck	: vinc-supply		: poly-phase capable
+DCDCD		: DC-DC	buck	: vind-supply		: poly-phase capable
+DCDCE		: DC-DC	buck	: vine-supply		: poly-phase capable
+ALDO1		: LDO		: aldoin-supply		: shared supply
+ALDO2		: LDO		: aldoin-supply		: shared supply
+ALDO3		: LDO		: aldoin-supply		: shared supply
+BLDO1		: LDO		: bldoin-supply		: shared supply
+BLDO2		: LDO		: bldoin-supply		: shared supply
+BLDO3		: LDO		: bldoin-supply		: shared supply
+BLDO4		: LDO		: bldoin-supply		: shared supply
+CLDO1		: LDO		: cldoin-supply		: shared supply
+CLDO2		: LDO		: cldoin-supply		: shared supply
+CLDO3		: LDO		: cldoin-supply		: shared supply
+SW		: On/Off Switch : swin-supply
+
+Additionally, the AXP806 DC-DC regulators support poly-phase arrangements
+for higher output current. The possible groupings are: A+B, A+B+C, D+E.
+
+AXP809 regulators, type, and corresponding input supply names:
+
+Regulator	  Type		  Supply Name		  Notes
+---------	  ----		  -----------		  -----
+DCDC1		: DC-DC buck	: vin1-supply
+DCDC2		: DC-DC buck	: vin2-supply
+DCDC3		: DC-DC	buck	: vin3-supply
+DCDC4		: DC-DC	buck	: vin4-supply
+DCDC5		: DC-DC	buck	: vin5-supply
+DC1SW		: On/Off Switch	:			: DCDC1 secondary output
+DC5LDO		: LDO		:			: input from DCDC5
+ALDO1		: LDO		: aldoin-supply		: shared supply
+ALDO2		: LDO		: aldoin-supply		: shared supply
+ALDO3		: LDO		: aldoin-supply		: shared supply
+DLDO1		: LDO		: dldoin-supply		: shared supply
+DLDO2		: LDO		: dldoin-supply		: shared supply
+ELDO1		: LDO		: eldoin-supply		: shared supply
+ELDO2		: LDO		: eldoin-supply		: shared supply
+ELDO3		: LDO		: eldoin-supply		: shared supply
+LDO_IO0		: LDO		: ips-supply		: GPIO 0
+LDO_IO1		: LDO		: ips-supply		: GPIO 1
+RTC_LDO		: LDO		: ips-supply		: always on
+SW		: On/Off Switch : swin-supply
+
+AXP813 regulators, type, and corresponding input supply names:
+
+Regulator	  Type		  Supply Name		  Notes
+---------	  ----		  -----------		  -----
+DCDC1		: DC-DC buck	: vin1-supply
+DCDC2		: DC-DC buck	: vin2-supply		: poly-phase capable
+DCDC3		: DC-DC	buck	: vin3-supply		: poly-phase capable
+DCDC4		: DC-DC	buck	: vin4-supply
+DCDC5		: DC-DC	buck	: vin5-supply		: poly-phase capable
+DCDC6		: DC-DC	buck	: vin6-supply		: poly-phase capable
+DCDC7		: DC-DC	buck	: vin7-supply
+ALDO1		: LDO		: aldoin-supply		: shared supply
+ALDO2		: LDO		: aldoin-supply		: shared supply
+ALDO3		: LDO		: aldoin-supply		: shared supply
+DLDO1		: LDO		: dldoin-supply		: shared supply
+DLDO2		: LDO		: dldoin-supply		: shared supply
+DLDO3		: LDO		: dldoin-supply		: shared supply
+DLDO4		: LDO		: dldoin-supply		: shared supply
+ELDO1		: LDO		: eldoin-supply		: shared supply
+ELDO2		: LDO		: eldoin-supply		: shared supply
+ELDO3		: LDO		: eldoin-supply		: shared supply
+FLDO1		: LDO		: fldoin-supply		: shared supply
+FLDO2		: LDO		: fldoin-supply		: shared supply
+FLDO3		: LDO		: fldoin-supply		: shared supply
+LDO_IO0		: LDO		: ips-supply		: GPIO 0
+LDO_IO1		: LDO		: ips-supply		: GPIO 1
+RTC_LDO		: LDO		: ips-supply		: always on
+SW		: On/Off Switch : swin-supply
+DRIVEVBUS	: Enable output	: drivevbus-supply	: external regulator
+
+Example:
+
+axp209: pmic@34 {
+	compatible = "x-powers,axp209";
+	reg = <0x34>;
+	interrupt-parent = <&nmi_intc>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	interrupt-controller;
+	#interrupt-cells = <1>;
+
+	regulators {
+		x-powers,dcdc-freq = <1500>;
+
+		vdd_cpu: dcdc2 {
+			regulator-always-on;
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1450000>;
+			regulator-name = "vdd-cpu";
+		};
+
+		vdd_int_dll: dcdc3 {
+			regulator-always-on;
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1400000>;
+			regulator-name = "vdd-int-dll";
+		};
+
+		vdd_rtc: ldo1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1400000>;
+			regulator-name = "vdd-rtc";
+		};
+
+		avcc: ldo2 {
+			regulator-always-on;
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-name = "avcc";
+		};
+
+		ldo3 {
+			/* unused but preferred to be managed by OS */
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/bd9571mwv.txt b/Documentation/devicetree/bindings/mfd/bd9571mwv.txt
new file mode 100644
index 000000000..8c4678650
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/bd9571mwv.txt
@@ -0,0 +1,69 @@
+* ROHM BD9571MWV Power Management Integrated Circuit (PMIC) bindings
+
+Required properties:
+ - compatible		: Should be "rohm,bd9571mwv".
+ - reg			: I2C slave address.
+ - interrupts		: The interrupt line the device is connected to.
+ - interrupt-controller	: Marks the device node as an interrupt controller.
+ - #interrupt-cells	: The number of cells to describe an IRQ, should be 2.
+			    The first cell is the IRQ number.
+			    The second cell is the flags, encoded as trigger
+			    masks from ../interrupt-controller/interrupts.txt.
+ - gpio-controller      : Marks the device node as a GPIO Controller.
+ - #gpio-cells          : Should be two.  The first cell is the pin number and
+                            the second cell is used to specify flags.
+                            See ../gpio/gpio.txt for more information.
+ - regulators:          : List of child nodes that specify the regulator
+                            initialization data. Child nodes must be named
+                            after their hardware counterparts:
+			     - vd09
+			     - vd18
+			     - vd25
+			     - vd33
+			     - dvfs
+			    Each child node is defined using the standard
+			    binding for regulators.
+
+Optional properties:
+  - rohm,ddr-backup-power : Value to use for DDR-Backup Power (default 0).
+			    This is a bitmask that specifies which DDR power
+			    rails need to be kept powered when backup mode is
+			    entered, for system suspend:
+			      - bit 0: DDR0
+			      - bit 1: DDR1
+			      - bit 2: DDR0C
+			      - bit 3: DDR1C
+			    These bits match the KEEPON_DDR* bits in the
+			    documentation for the "BKUP Mode Cnt" register.
+  - rohm,rstbmode-level: The RSTB signal is configured for level mode, to
+			 accommodate a toggle power switch (the RSTBMODE pin is
+			 strapped low).
+  - rohm,rstbmode-pulse: The RSTB signal is configured for pulse mode, to
+			 accommodate a momentary power switch (the RSTBMODE pin
+			 is strapped high).
+			 The two properties above are mutually exclusive.
+
+Example:
+
+	pmic: pmic@30 {
+		compatible = "rohm,bd9571mwv";
+		reg = <0x30>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		rohm,ddr-backup-power = <0xf>;
+		rohm,rstbmode-pulse;
+
+		regulators {
+			dvfs: dvfs {
+				regulator-name = "dvfs";
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1030000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/bfticu.txt b/Documentation/devicetree/bindings/mfd/bfticu.txt
new file mode 100644
index 000000000..538192fda
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/bfticu.txt
@@ -0,0 +1,24 @@
+KEYMILE bfticu Chassis Management FPGA
+
+The bfticu is a multifunction device that manages the whole chassis.
+Its main functionality is to collect IRQs from the whole chassis and signals
+them to a single controller.
+
+Required properties:
+- compatible: "keymile,bfticu"
+- interrupt-controller: the bfticu FPGA is an interrupt controller
+- interrupts: the main IRQ line to signal the collected IRQs
+- #interrupt-cells : is 2 and their usage is compliant to the 2 cells variant
+  of Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+- reg: access on the parent local bus (chip select, offset in chip select, size)
+
+Example:
+
+	chassis-mgmt@3,0 {
+		compatible = "keymile,bfticu";
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		reg = <3 0 0x100>;
+		interrupt-parent = <&mpic>;
+		interrupts = <6 1 0 0>;
+	};
diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm59056.txt b/Documentation/devicetree/bindings/mfd/brcm,bcm59056.txt
new file mode 100644
index 000000000..be51a15e0
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/brcm,bcm59056.txt
@@ -0,0 +1,39 @@
+-------------------------------
+BCM590xx Power Management Units
+-------------------------------
+
+Required properties:
+- compatible: "brcm,bcm59056"
+- reg: I2C slave address
+- interrupts: interrupt for the PMU. Generic interrupt client node bindings
+  are described in interrupt-controller/interrupts.txt
+
+------------------
+Voltage Regulators
+------------------
+
+Optional child nodes:
+- regulators: container node for regulators following the generic
+  regulator binding in regulator/regulator.txt
+
+  The valid regulator node names for BCM59056 are:
+  	rfldo, camldo1, camldo2, simldo1, simldo2, sdldo, sdxldo,
+	mmcldo1, mmcldo2, audldo, micldo, usbldo, vibldo,
+	csr, iosr1, iosr2, msr, sdsr1, sdsr2, vsr,
+	gpldo1, gpldo2, gpldo3, gpldo4, gpldo5, gpldo6,
+	vbus
+
+Example:
+	pmu: bcm59056@8 {
+		compatible = "brcm,bcm59056";
+		reg = <0x08>;
+		interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+		regulators {
+			rfldo_reg: rfldo {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			...
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/brcm,iproc-cdru.txt b/Documentation/devicetree/bindings/mfd/brcm,iproc-cdru.txt
new file mode 100644
index 000000000..82f82e069
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/brcm,iproc-cdru.txt
@@ -0,0 +1,16 @@
+Broadcom iProc Chip Device Resource Unit (CDRU)
+
+Various Broadcom iProc SoCs have a set of registers that provide various
+chip specific device and resource configurations. This node allows access to
+these CDRU registers via syscon.
+
+Required properties:
+- compatible: should contain:
+		"brcm,sr-cdru", "syscon" for Stingray
+- reg: base address and range of the CDRU registers
+
+Example:
+	cdru: syscon@6641d000 {
+		compatible = "brcm,sr-cdru", "syscon";
+		reg = <0 0x6641d000 0 0x400>;
+	};
diff --git a/Documentation/devicetree/bindings/mfd/brcm,iproc-mhb.txt b/Documentation/devicetree/bindings/mfd/brcm,iproc-mhb.txt
new file mode 100644
index 000000000..4421e9771
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/brcm,iproc-mhb.txt
@@ -0,0 +1,18 @@
+Broadcom iProc Multi Host Bridge (MHB)
+
+Certain Broadcom iProc SoCs have a multi host bridge (MHB) block that controls
+the connection and configuration of 1) internal PCIe serdes; 2) PCIe endpoint
+interface; 3) access to the Nitro (network processing) engine
+
+This node allows access to these MHB registers via syscon.
+
+Required properties:
+- compatible: should contain:
+		"brcm,sr-mhb", "syscon" for Stingray
+- reg: base address and range of the MHB registers
+
+Example:
+	mhb: syscon@60401000 {
+		compatible = "brcm,sr-mhb", "syscon";
+		reg = <0 0x60401000 0 0x38c>;
+	};
diff --git a/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.yaml b/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.yaml
new file mode 100644
index 000000000..c00ad3e21
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.yaml
@@ -0,0 +1,360 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/cirrus,lochnagar.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic Lochnagar Audio Development Board
+
+maintainers:
+  - patches@opensource.cirrus.com
+
+description: |
+  Lochnagar is an evaluation and development board for Cirrus Logic
+  Smart CODEC and Amp devices. It allows the connection of most Cirrus
+  Logic devices on mini-cards, as well as allowing connection of
+  various application processor systems to provide a full evaluation
+  platform.  Audio system topology, clocking and power can all be
+  controlled through the Lochnagar, allowing the device under test
+  to be used in a variety of possible use cases.
+
+  Also see these documents for generic binding information:
+    [1] GPIO : ../gpio/gpio.txt
+
+  And these for relevant defines:
+    [2] include/dt-bindings/pinctrl/lochnagar.h
+    [3] include/dt-bindings/clock/lochnagar.h
+
+  And these documents for the required sub-node binding details:
+    [4] Clock: ../clock/cirrus,lochnagar.yaml
+    [5] Pinctrl: ../pinctrl/cirrus,lochnagar.yaml
+    [6] Sound: ../sound/cirrus,lochnagar.yaml
+    [7] Hardware Monitor: ../hwmon/cirrus,lochnagar.yaml
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          enum:
+            - cirrus,lochnagar2
+    then:
+      properties:
+        lochnagar-hwmon:
+          type: object
+          $ref: /schemas/hwmon/cirrus,lochnagar.yaml#
+
+        lochnagar-sc:
+          type: object
+          $ref: /schemas/sound/cirrus,lochnagar.yaml#
+
+properties:
+  compatible:
+    enum:
+      - cirrus,lochnagar1
+      - cirrus,lochnagar2
+
+  reg:
+    const: 0x22
+
+  reset-gpios:
+    maxItems: 1
+
+  present-gpios:
+    description: |
+      Host present line, indicating the presence of a
+      host system, see [1]. This can be omitted if the present line is
+      tied in hardware.
+    maxItems: 1
+
+  lochnagar-clk:
+    type: object
+    $ref: /schemas/clock/cirrus,lochnagar.yaml#
+
+  lochnagar-pmic32k:
+    type: object
+    $ref: /schemas/clock/fixed-clock.yaml#
+    properties:
+      clock-frequency:
+        const: 32768
+
+  lochnagar-clk12m:
+    type: object
+    $ref: /schemas/clock/fixed-clock.yaml#
+    properties:
+      clock-frequency:
+        const: 12288000
+
+  lochnagar-clk11m:
+    type: object
+    $ref: /schemas/clock/fixed-clock.yaml#
+    properties:
+      clock-frequency:
+        const: 11298600
+
+  lochnagar-clk24m:
+    type: object
+    $ref: /schemas/clock/fixed-clock.yaml#
+    properties:
+      clock-frequency:
+        const: 24576000
+
+  lochnagar-clk22m:
+    type: object
+    $ref: /schemas/clock/fixed-clock.yaml#
+    properties:
+      clock-frequency:
+        const: 22579200
+
+  lochnagar-clk8m:
+    type: object
+    $ref: /schemas/clock/fixed-clock.yaml#
+    properties:
+      clock-frequency:
+        const: 8192000
+
+  lochnagar-usb24m:
+    type: object
+    $ref: /schemas/clock/fixed-clock.yaml#
+    properties:
+      clock-frequency:
+        const: 24576000
+
+  lochnagar-usb12m:
+    type: object
+    $ref: /schemas/clock/fixed-clock.yaml#
+    properties:
+      clock-frequency:
+        const: 12288000
+
+  lochnagar-pinctrl:
+    type: object
+    $ref: /schemas/pinctrl/cirrus,lochnagar.yaml#
+
+  lochnagar-hwmon:
+    type: object
+    $ref: /schemas/hwmon/cirrus,lochnagar.yaml#
+
+  lochnagar-sc:
+    type: object
+    $ref: /schemas/sound/cirrus,lochnagar.yaml#
+
+  VDDCORE:
+    description:
+      Initialisation data for the VDDCORE regulator, which supplies the
+      CODECs digital core if not being provided by an internal regulator.
+    type: object
+    $ref: /schemas/regulator/regulator.yaml#
+    properties:
+      compatible:
+        enum:
+          - cirrus,lochnagar2-vddcore
+
+      SYSVDD-supply:
+        description:
+          Primary power supply for the Lochnagar.
+    required:
+      - compatible
+
+  MICVDD:
+    description:
+      Initialisation data for the MICVDD regulator, which supplies the
+      CODECs MICVDD.
+    type: object
+    $ref: /schemas/regulator/regulator.yaml#
+    properties:
+      compatible:
+        enum:
+          - cirrus,lochnagar2-micvdd
+
+      SYSVDD-supply:
+        description:
+          Primary power supply for the Lochnagar.
+    required:
+      - compatible
+
+  MIC1VDD:
+    description:
+      Initialisation data for the MIC1VDD supplies.
+    type: object
+    $ref: /schemas/regulator/regulator.yaml#
+    properties:
+      compatible:
+        enum:
+          - cirrus,lochnagar2-mic1vdd
+
+      cirrus,micbias-input:
+        description:
+          A property selecting which of the CODEC minicard micbias outputs
+          should be used.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 1
+        maximum: 4
+
+      MICBIAS1-supply:
+        description:
+          Regulator supplies for the MIC1VDD outputs, supplying the digital
+          microphones, normally supplied from the attached CODEC.
+    required:
+      - compatible
+
+  MIC2VDD:
+    description:
+      Initialisation data for the MIC2VDD supplies.
+    type: object
+    $ref: /schemas/regulator/regulator.yaml#
+    properties:
+      compatible:
+        enum:
+          - cirrus,lochnagar2-mic2vdd
+
+      cirrus,micbias-input:
+        description:
+          A property selecting which of the CODEC minicard micbias outputs
+          should be used.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 1
+        maximum: 4
+
+      MICBIAS2-supply:
+        description:
+          Regulator supplies for the MIC2VDD outputs, supplying the digital
+          microphones, normally supplied from the attached CODEC.
+    required:
+      - compatible
+
+  VDD1V8:
+    description:
+      Recommended fixed regulator for the VDD1V8 regulator, which supplies
+      the CODECs analog and 1.8V digital supplies.
+    type: object
+    $ref: /schemas/regulator/regulator.yaml#
+    properties:
+      compatible:
+        enum:
+          - regulator-fixed
+
+      regulator-min-microvolt:
+        const: 1800000
+
+      regulator-max-microvolt:
+        const: 1800000
+
+      vin-supply:
+        description:
+          Should be set to same supply as SYSVDD
+    required:
+      - compatible
+      - regulator-min-microvolt
+      - regulator-max-microvolt
+      - regulator-boot-on
+      - regulator-always-on
+      - vin-supply
+
+required:
+  - compatible
+  - reg
+  - reset-gpios
+  - lochnagar-clk
+  - lochnagar-pinctrl
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clk/lochnagar.h>
+    #include <dt-bindings/pinctrl/lochnagar.h>
+    i2c@e0004000 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        reg = <0xe0004000 0x1000>;
+
+        lochnagar: lochnagar@22 {
+            compatible = "cirrus,lochnagar2";
+            reg = <0x22>;
+
+            reset-gpios = <&gpio0 55 0>;
+            present-gpios = <&gpio0 60 0>;
+
+            lochnagarclk: lochnagar-clk {
+                compatible = "cirrus,lochnagar2-clk";
+
+                #clock-cells = <1>;
+                clocks = <&clkaudio>, <&clkpmic>;
+                clock-names = "ln-gf-mclk2", "ln-pmic-32k";
+
+                assigned-clocks = <&lochnagarclk LOCHNAGAR_CDC_MCLK1>,
+                                  <&lochnagarclk LOCHNAGAR_CDC_MCLK2>;
+                assigned-clock-parents = <&clkaudio>, <&clkpmic>;
+            };
+
+            clkpmic: lochnagar-pmic32k {
+                compatible = "fixed-clock";
+                #clock-cells = <0>;
+                clock-frequency = <32768>;
+            };
+
+            lochnagar-pinctrl {
+                compatible = "cirrus,lochnagar-pinctrl";
+
+                gpio-controller;
+                #gpio-cells = <2>;
+                gpio-ranges = <&lochnagar 0 0 LOCHNAGAR2_PIN_NUM_GPIOS>;
+
+                pinctrl-names = "default";
+                pinctrl-0 = <&pinsettings>;
+
+                pinsettings: pin-settings {
+                    ap2aif-pins {
+                        input-enable;
+                        groups = "gf-aif1";
+                        function = "codec-aif3";
+                    };
+                    codec2aif-pins {
+                        output-enable;
+                        groups = "codec-aif3";
+                        function = "gf-aif1";
+                    };
+                };
+            };
+
+            lochnagar-sc {
+                compatible = "cirrus,lochnagar2-soundcard";
+
+                #sound-dai-cells = <1>;
+
+                clocks = <&lochnagarclk LOCHNAGAR_SOUNDCARD_MCLK>;
+                clock-names = "mclk";
+            };
+
+            lochnagar-hwmon {
+                compatible = "cirrus,lochnagar2-hwmon";
+            };
+
+            MIC1VDD {
+                compatible = "cirrus,lochnagar2-mic1vdd";
+
+                cirrus,micbias-input = <3>;
+            };
+
+            MICVDD {
+                compatible = "cirrus,lochnagar2-micvdd";
+
+                SYSVDD-supply = <&wallvdd>;
+
+                regulator-min-microvolt = <3300000>;
+                regulator-max-microvolt = <3300000>;
+            };
+
+            VDD1V8 {
+                compatible = "regulator-fixed";
+
+                regulator-name = "VDD1V8";
+                regulator-min-microvolt = <1800000>;
+                regulator-max-microvolt = <1800000>;
+                regulator-boot-on;
+                regulator-always-on;
+
+                vin-supply = <&wallvdd>;
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mfd/cirrus,madera.yaml b/Documentation/devicetree/bindings/mfd/cirrus,madera.yaml
new file mode 100644
index 000000000..499c62c04
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/cirrus,madera.yaml
@@ -0,0 +1,299 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/cirrus,madera.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic Madera class audio CODECs Multi-Functional Device
+
+maintainers:
+  - patches@opensource.cirrus.com
+
+description: |
+  These devices are audio SoCs with extensive digital capabilities and a range
+  of analogue I/O.
+
+  See also the child driver bindings in:
+
+    bindings/pinctrl/cirrus,madera.yaml
+    bindings/regulator/wlf,arizona.yaml
+    bindings/sound/cirrus,madera.yaml
+
+allOf:
+  - $ref: /schemas/pinctrl/cirrus,madera.yaml#
+  - $ref: /schemas/regulator/wlf,arizona.yaml#
+  - $ref: /schemas/sound/cirrus,madera.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - cirrus,cs47l85
+              - wlf,wm1840
+    then:
+      properties:
+        SPKVDDL-supply:
+          description:
+            Left speaker driver power supply.
+
+        SPKVDDR-supply:
+          description:
+            Right speaker driver power supply.
+
+      required:
+        - SPKVDDL-supply
+        - SPKVDDR-supply
+    else:
+      required:
+        - DCVDD-supply
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - cirrus,cs47l15
+              - cirrus,cs47l35
+    then:
+      properties:
+        SPKVDD-supply:
+          description:
+            Mono speaker driver power supply.
+
+      required:
+        - SPKVDD-supply
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - cirrus,cs47l35
+              - cirrus,cs47l85
+              - cirrus,cs47l90
+              - cirrus,cs47l91
+              - wlf,wm1840
+    then:
+      properties:
+        DBVDD2-supply:
+          description:
+            Databus power supply.
+
+      required:
+        - DBVDD2-supply
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - cirrus,cs47l85
+              - cirrus,cs47l90
+              - cirrus,cs47l91
+              - wlf,wm1840
+    then:
+      properties:
+        DBVDD3-supply:
+          description:
+            Databus power supply.
+
+        DBVDD4-supply:
+          description:
+            Databus power supply.
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - cirrus,cs47l15
+    then:
+      required:
+        - MICVDD-supply
+    else:
+      properties:
+        CPVDD2-supply:
+          description:
+            Secondary charge pump power supply.
+
+      required:
+        - CPVDD2-supply
+
+properties:
+  compatible:
+    enum:
+      - cirrus,cs47l15
+      - cirrus,cs47l35
+      - cirrus,cs47l85
+      - cirrus,cs47l90
+      - cirrus,cs47l91
+      - cirrus,cs42l92
+      - cirrus,cs47l92
+      - cirrus,cs47l93
+      - cirrus,wm1840
+
+  reg:
+    maxItems: 1
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    description:
+      The first cell is the pin number. The second cell is reserved for
+      future use and must be zero
+    const: 2
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    description:
+      The first cell is the IRQ number.
+      The second cell is the flags, encoded as the trigger masks from
+      bindings/interrupt-controller/interrupts.txt
+    const: 2
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    description:
+      One entry specifying the GPIO controlling /RESET.  As defined in
+      bindings/gpio.txt.  Although optional, it is strongly recommended
+      to use a hardware reset.
+    maxItems: 1
+
+  clocks:
+    description:
+      Should reference the clocks supplied on MCLK1, MCLK2 and MCLK3.
+    minItems: 1
+    maxItems: 3
+
+  clock-names:
+    description: |
+      May contain up to three strings:
+        "mclk1" For the clock supplied on MCLK1, recommended to be a
+                high quality audio reference clock.
+        "mclk2" For the clock supplied on MCLK2, required to be an
+                always on 32k clock.
+        "mclk3" For the clock supplied on MCLK3.
+    oneOf:
+      - items:
+          - const: mclk1
+      - items:
+          - const: mclk2
+      - items:
+          - const: mclk3
+      - items:
+          - const: mclk1
+          - const: mclk2
+      - items:
+          - const: mclk1
+          - const: mclk3
+      - items:
+          - const: mclk2
+          - const: mclk3
+      - items:
+          - const: mclk1
+          - const: mclk2
+          - const: mclk3
+
+  AVDD-supply:
+    description:
+      Analogue power supply.
+
+  DBVDD1-supply:
+    description:
+      Databus power supply.
+
+  CPVDD1-supply:
+    description:
+      Charge pump power supply.
+
+  DCVDD-supply:
+    description:
+      Digital power supply, optional on CS47L85, WM1840 where it can
+      be supplied internally.
+
+  MICVDD-supply:
+    description:
+      Microphone power supply, normally supplied internally except on
+      cs47l24, wm1831 where it is mandatory.
+
+required:
+  - compatible
+  - gpio-controller
+  - '#gpio-cells'
+  - interrupt-controller
+  - '#interrupt-cells'
+  - interrupt-parent
+  - interrupts
+  - AVDD-supply
+  - DBVDD1-supply
+  - CPVDD1-supply
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/sound/madera.h>
+    i2c@e0004000 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        reg = <0xe0004000 0x1000>;
+
+        cs47l85: codec@1a {
+            compatible = "cirrus,cs47l85";
+            reg = <0x1a>;
+
+            reset-gpios = <&gpio 0>;
+            wlf,ldoena = <&gpio 1>;
+
+            interrupt-controller;
+            #interrupt-cells = <2>;
+            interrupts = <&host_irq1>;
+            interrupt-parent = <&gic>;
+
+            gpio-controller;
+            #gpio-cells = <2>;
+
+            AVDD-supply = <&vdd1v8>;
+            DBVDD1-supply = <&vdd1v8>;
+            DBVDD2-supply = <&vdd1v8>;
+            DBVDD3-supply = <&vdd1v8>;
+            DBVDD4-supply = <&vdd1v8>;
+            CPVDD1-supply = <&vdd1v8>;
+            CPVDD2-supply = <&vdd1v2>;
+            SPKVDDL-supply = <&vdd5v>;
+            SPKVDDR-supply = <&vdd5v>;
+
+            clocks = <&clks 0>, <&clks 1>, <&clks 2>;
+            clock-names = "mclk1", "mclk2", "mclk3";
+
+            cirrus,dmic-ref = <0 0 MADERA_DMIC_REF_MICBIAS1>;
+            cirrus,inmode = <
+                MADERA_INMODE_SE   MADERA_INMODE_SE
+                MADERA_INMODE_SE   MADERA_INMODE_SE
+                MADERA_INMODE_DIFF MADERA_INMODE_DIFF
+            >;
+            cirrus,max-channels-clocked = <2 0 0>;
+
+            pinctrl-names = "default";
+            pinctrl-0 = <&pinsettings>;
+
+            pinsettings: pin-settings {
+                aif1-pins {
+                    groups = "aif1";
+                    function = "aif1";
+                    bias-bus-hold;
+                };
+
+                aif2-pins {
+                    groups = "aif2";
+                    function = "aif2";
+                    bias-bus-hold;
+                };
+
+                aif3-pins {
+                    groups = "aif3";
+                    function = "aif3";
+                    bias-bus-hold;
+                };
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt
new file mode 100644
index 000000000..07c69c0c6
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt
@@ -0,0 +1,67 @@
+* Dialog DA9052/53 Power Management Integrated Circuit (PMIC)
+
+Required properties:
+- compatible : Should be "dlg,da9052", "dlg,da9053-aa",
+			 "dlg,da9053-ab", or "dlg,da9053-bb"
+
+Optional properties:
+- dlg,tsi-as-adc : Boolean, if set the X+, X-, Y+, Y- touchscreen
+                    input lines are used as general purpose analogue
+					input.
+- tsiref-supply: Phandle to the regulator, which provides the reference
+                 voltage for the TSIREF pin. Must be provided when the
+			     touchscreen pins are used for ADC purposes.
+
+Sub-nodes:
+- regulators : Contain the regulator nodes. The DA9052/53 regulators are
+  bound using their names as listed below:
+
+    buck1     : regulator BUCK CORE
+    buck2     : regulator BUCK PRO
+    buck3     : regulator BUCK MEM
+    buck4     : regulator BUCK PERI
+    ldo1      : regulator LDO1
+    ldo2      : regulator LDO2
+    ldo3      : regulator LDO3
+    ldo4      : regulator LDO4
+    ldo5      : regulator LDO5
+    ldo6      : regulator LDO6
+    ldo7      : regulator LDO7
+    ldo8      : regulator LDO8
+    ldo9      : regulator LDO9
+    ldo10     : regulator LDO10
+
+  The bindings details of individual regulator device can be found in:
+  Documentation/devicetree/bindings/regulator/regulator.txt
+
+Examples:
+
+i2c@63fc8000 { /* I2C1 */
+
+	pmic: dialog@48 {
+		compatible = "dlg,da9053-aa";
+		reg = <0x48>;
+
+		regulators {
+			buck1 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <2075000>;
+			};
+
+			buck2 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <2075000>;
+			};
+
+			buck3 {
+				regulator-min-microvolt = <925000>;
+				regulator-max-microvolt = <2500000>;
+			};
+
+			buck4 {
+				regulator-min-microvolt = <925000>;
+				regulator-max-microvolt = <2500000>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/da9055.txt b/Documentation/devicetree/bindings/mfd/da9055.txt
new file mode 100644
index 000000000..131a53283
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/da9055.txt
@@ -0,0 +1,70 @@
+* Dialog DA9055 Power Management Integrated Circuit (PMIC)
+
+DA9055 consists of a large and varied group of sub-devices (I2C Only):
+
+Device			 Supply Names	 Description
+------			 ------------	 -----------
+da9055-gpio		:		: GPIOs
+da9055-regulator	:		: Regulators
+da9055-onkey		:		: On key
+da9055-rtc		:		: RTC
+da9055-hwmon		:		: ADC
+da9055-watchdog		:		: Watchdog
+
+The CODEC device in DA9055 has a separate, configurable I2C address and so
+is instantiated separately from the PMIC.
+
+For details on accompanying CODEC I2C device, see the following:
+Documentation/devicetree/bindings/sound/da9055.txt
+
+======
+
+Required properties:
+- compatible : Should be "dlg,da9055-pmic"
+- reg: Specifies the I2C slave address (defaults to 0x5a but can be modified)
+- interrupts: IRQ line info for da9055 chip.
+- interrupt-controller: da9055 has internal IRQs (has own IRQ domain).
+- #interrupt-cells: Should be 1, is the local IRQ number for da9055.
+
+Sub-nodes:
+- regulators : Contain the regulator nodes. The DA9055 regulators are
+  bound using their names as listed below:
+
+    buck1     : regulator BUCK1
+    buck2     : regulator BUCK2
+    ldo1      : regulator LDO1
+    ldo2      : regulator LDO2
+    ldo3      : regulator LDO3
+    ldo4      : regulator LDO4
+    ldo5      : regulator LDO5
+    ldo6      : regulator LDO6
+
+  The bindings details of individual regulator device can be found in:
+  Documentation/devicetree/bindings/regulator/regulator.txt
+
+
+Example:
+
+	pmic: da9055-pmic@5a {
+		compatible = "dlg,da9055-pmic";
+		reg = <0x5a>;
+		interrupt-parent = <&intc>;
+		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		regulators {
+			buck1: BUCK1 {
+				regulator-min-microvolt = <725000>;
+				regulator-max-microvolt = <2075000>;
+			};
+			buck2: BUCK2 {
+				regulator-min-microvolt = <925000>;
+				regulator-max-microvolt = <2500000>;
+			};
+			ldo1: LDO1 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/da9062.txt b/Documentation/devicetree/bindings/mfd/da9062.txt
new file mode 100644
index 000000000..bab0d0e66
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/da9062.txt
@@ -0,0 +1,123 @@
+* Dialog DA9062 Power Management Integrated Circuit (PMIC)
+
+Product information for the DA9062 and DA9061 devices can be found here:
+- https://www.dialog-semiconductor.com/products/da9062
+- https://www.dialog-semiconductor.com/products/da9061
+
+The DA9062 PMIC consists of:
+
+Device                   Supply Names    Description
+------                   ------------    -----------
+da9062-regulator        :               : LDOs & BUCKs
+da9062-rtc              :               : Real-Time Clock
+da9062-onkey            :               : On Key
+da9062-watchdog         :               : Watchdog Timer
+da9062-thermal          :               : Thermal
+da9062-gpio             :               : GPIOs
+
+The DA9061 PMIC consists of:
+
+Device                   Supply Names    Description
+------                   ------------    -----------
+da9062-regulator        :               : LDOs & BUCKs
+da9062-onkey            :               : On Key
+da9062-watchdog         :               : Watchdog Timer
+da9062-thermal          :               : Thermal
+
+======
+
+Required properties:
+
+- compatible : Should be
+    "dlg,da9062" for DA9062
+    "dlg,da9061" for DA9061
+- reg : Specifies the I2C slave address (this defaults to 0x58 but it can be
+  modified to match the chip's OTP settings).
+- interrupts : IRQ line information.
+- interrupt-controller
+
+See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for
+further information on IRQ bindings.
+
+Optional properties:
+
+- gpio-controller : Marks the device as a gpio controller.
+- #gpio-cells     : Should be two. The first cell is the pin number and the
+                    second cell is used to specify the gpio polarity.
+
+See Documentation/devicetree/bindings/gpio/gpio.txt for further information on
+GPIO bindings.
+
+Sub-nodes:
+
+- regulators : This node defines the settings for the LDOs and BUCKs.
+  The DA9062 regulators are bound using their names listed below:
+
+    buck1    : BUCK_1
+    buck2    : BUCK_2
+    buck3    : BUCK_3
+    buck4    : BUCK_4
+    ldo1     : LDO_1
+    ldo2     : LDO_2
+    ldo3     : LDO_3
+    ldo4     : LDO_4
+
+  The DA9061 regulators are bound using their names listed below:
+
+    buck1    : BUCK_1
+    buck2    : BUCK_2
+    buck3    : BUCK_3
+    ldo1     : LDO_1
+    ldo2     : LDO_2
+    ldo3     : LDO_3
+    ldo4     : LDO_4
+
+  The component follows the standard regulator framework and the bindings
+  details of individual regulator device can be found in:
+  Documentation/devicetree/bindings/regulator/regulator.txt
+
+  regulator-initial-mode may be specified for buck regulators using mode values
+  from include/dt-bindings/regulator/dlg,da9063-regulator.h.
+
+- rtc : This node defines settings required for the Real-Time Clock associated
+  with the DA9062. There are currently no entries in this binding, however
+  compatible = "dlg,da9062-rtc" should be added if a node is created.
+
+- onkey : See ../input/da9062-onkey.txt
+
+- watchdog: See ../watchdog/da9062-watchdog.txt
+
+- thermal : See ../thermal/da9062-thermal.txt
+
+Example:
+
+	pmic0: da9062@58 {
+		compatible = "dlg,da9062";
+		reg = <0x58>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+
+		rtc {
+			compatible = "dlg,da9062-rtc";
+		};
+
+		regulators {
+			DA9062_BUCK1: buck1 {
+				regulator-name = "BUCK1";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1570000>;
+				regulator-min-microamp = <500000>;
+				regulator-max-microamp = <2000000>;
+				regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
+				regulator-boot-on;
+			};
+			DA9062_LDO1: ldo1 {
+				regulator-name = "LDO_1";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-boot-on;
+			};
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/mfd/da9063.txt b/Documentation/devicetree/bindings/mfd/da9063.txt
new file mode 100644
index 000000000..8da879935
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/da9063.txt
@@ -0,0 +1,111 @@
+* Dialog DA9063/DA9063L Power Management Integrated Circuit (PMIC)
+
+DA9093 consists of a large and varied group of sub-devices (I2C Only):
+
+Device                   Supply Names    Description
+------                   ------------    -----------
+da9063-regulator        :               : LDOs & BUCKs
+da9063-onkey            :               : On Key
+da9063-rtc              :               : Real-Time Clock (DA9063 only)
+da9063-watchdog         :               : Watchdog
+
+======
+
+Required properties:
+
+- compatible : Should be "dlg,da9063" or "dlg,da9063l"
+- reg : Specifies the I2C slave address (this defaults to 0x58 but it can be
+  modified to match the chip's OTP settings).
+- interrupts : IRQ line information.
+- interrupt-controller
+
+Sub-nodes:
+
+- regulators : This node defines the settings for the LDOs and BUCKs.
+  The DA9063(L) regulators are bound using their names listed below:
+
+    bcore1    : BUCK CORE1
+    bcore2    : BUCK CORE2
+    bpro      : BUCK PRO
+    bmem      : BUCK MEM
+    bio       : BUCK IO
+    bperi     : BUCK PERI
+    ldo1      : LDO_1	(DA9063 only)
+    ldo2      : LDO_2	(DA9063 only)
+    ldo3      : LDO_3
+    ldo4      : LDO_4	(DA9063 only)
+    ldo5      : LDO_5	(DA9063 only)
+    ldo6      : LDO_6	(DA9063 only)
+    ldo7      : LDO_7
+    ldo8      : LDO_8
+    ldo9      : LDO_9
+    ldo10     : LDO_10	(DA9063 only)
+    ldo11     : LDO_11
+
+  The component follows the standard regulator framework and the bindings
+  details of individual regulator device can be found in:
+  Documentation/devicetree/bindings/regulator/regulator.txt
+
+- rtc : This node defines settings for the Real-Time Clock associated with
+  the DA9063 only. The RTC is not present in DA9063L. There are currently
+  no entries in this binding, however compatible = "dlg,da9063-rtc" should
+  be added if a node is created.
+
+- onkey : This node defines the OnKey settings for controlling the key
+  functionality of the device. The node should contain the compatible property
+  with the value "dlg,da9063-onkey".
+
+  Optional onkey properties:
+
+  - dlg,disable-key-power : Disable power-down using a long key-press. If this
+    entry exists the OnKey driver will remove support for the KEY_POWER key
+    press. If this entry does not exist then by default the key-press
+    triggered power down is enabled and the OnKey will support both KEY_POWER
+    and KEY_SLEEP.
+
+- watchdog : This node defines settings for the Watchdog timer associated
+  with the DA9063 and DA9063L. There are currently no entries in this
+  binding, however compatible = "dlg,da9063-watchdog" should be added
+  if a node is created.
+
+
+Example:
+
+	pmic0: da9063@58 {
+		compatible = "dlg,da9063"
+		reg = <0x58>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+
+		rtc {
+			compatible = "dlg,da9063-rtc";
+		};
+
+		wdt {
+			compatible = "dlg,da9063-watchdog";
+		};
+
+		onkey {
+			compatible = "dlg,da9063-onkey";
+			dlg,disable-key-power;
+		};
+
+		regulators {
+			DA9063_BCORE1: bcore1 {
+				regulator-name = "BCORE1";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1570000>;
+				regulator-min-microamp = <500000>;
+				regulator-max-microamp = <2000000>;
+				regulator-boot-on;
+			};
+			DA9063_LDO11: ldo11 {
+				regulator-name = "LDO_11";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-boot-on;
+			};
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/mfd/da9150.txt b/Documentation/devicetree/bindings/mfd/da9150.txt
new file mode 100644
index 000000000..f09b41fbd
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/da9150.txt
@@ -0,0 +1,60 @@
+Dialog Semiconductor DA9150 Combined Charger/Fuel-Gauge MFD bindings
+
+DA9150 consists of a group of sub-devices:
+
+Device			 Description
+------			 -----------
+da9150-gpadc		: General Purpose ADC
+da9150-charger		: Battery Charger
+da9150-fg		: Battery Fuel-Gauge
+
+======
+
+Required properties:
+- compatible : Should be "dlg,da9150"
+- reg: Specifies the I2C slave address
+- interrupts: IRQ line info for da9150 chip.
+- interrupt-controller: da9150 has internal IRQs (own IRQ domain).
+  (See ../interrupt-controller/interrupts.txt for
+   further information relating to interrupt properties)
+
+Sub-devices:
+- da9150-gpadc: See ../iio/adc/da9150-gpadc.txt
+- da9150-charger: See ../power/da9150-charger.txt
+- da9150-fg: See ../power/da9150-fg.txt
+
+Example:
+
+	charger_fg: da9150@58 {
+		compatible = "dlg,da9150";
+		reg = <0x58>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+
+		gpadc: da9150-gpadc {
+			compatible = "dlg,da9150-gpadc";
+			#io-channel-cells = <1>;
+		};
+
+		charger {
+			compatible = "dlg,da9150-charger";
+
+			io-channels = <&gpadc 0>,
+				      <&gpadc 2>,
+				      <&gpadc 8>,
+				      <&gpadc 5>;
+			io-channel-names = "CHAN_IBUS",
+					   "CHAN_VBUS",
+					   "CHAN_TJUNC",
+					   "CHAN_VBAT";
+		};
+
+		fuel-gauge {
+			compatible = "dlg,da9150-fuel-gauge";
+
+			dlg,update-interval = <10000>;
+			dlg,warn-soc-level = /bits/ 8 <15>;
+			dlg,crit-soc-level = /bits/ 8 <5>
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/ene-kb3930.yaml b/Documentation/devicetree/bindings/mfd/ene-kb3930.yaml
new file mode 100644
index 000000000..08af356f5
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/ene-kb3930.yaml
@@ -0,0 +1,55 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/ene-kb3930.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ENE KB3930 Embedded Controller bindings
+
+description: |
+  This binding describes the ENE KB3930 Embedded Controller attached to an
+  I2C bus.
+
+maintainers:
+  - Lubomir Rintel <lkundrak@v3.sk>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - dell,wyse-ariel-ec  # Dell Wyse Ariel board (3020)
+      - const: ene,kb3930
+  reg:
+    maxItems: 1
+
+  off-gpios:
+    description: GPIO used with the shutdown protocol on Ariel
+    maxItems: 2
+
+  system-power-controller: true
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      embedded-controller@58 {
+        compatible = "dell,wyse-ariel-ec", "ene,kb3930";
+        reg = <0x58>;
+        system-power-controller;
+
+        off-gpios = <&gpio 126 GPIO_ACTIVE_HIGH>,
+                    <&gpio 127 GPIO_ACTIVE_HIGH>;
+      };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt b/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt
new file mode 100644
index 000000000..b03505286
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt
@@ -0,0 +1,47 @@
+Freescale MX25 ADC/TSC MultiFunction Device (MFD)
+
+This device combines two general purpose conversion queues one used for general
+ADC and the other used for touchscreens.
+
+Required properties:
+ - compatible:			Should be "fsl,imx25-tsadc".
+ - reg:				Start address and size of the memory area of
+ 					the device
+ - interrupts:			Interrupt for this device
+					(See: ../interrupt-controller/interrupts.txt)
+ - clocks:			An 'ipg' clock (See: ../clock/clock-bindings.txt)
+ - interrupt-controller:	This device is an interrupt controller. It
+   					controls the interrupts of both
+					conversion queues.
+ - #interrupt-cells:		Should be '<1>'.
+ - #address-cells:		Should be '<1>'.
+ - #size-cells:			Should be '<1>'.
+
+This device includes two conversion queues which can be added as subnodes.
+The first queue is for the touchscreen, the second for general purpose ADC.
+
+Example:
+	tscadc: tscadc@50030000 {
+		compatible = "fsl,imx25-tsadc";
+		reg = <0x50030000 0xc>;
+		interrupts = <46>;
+		clocks = <&clks 119>;
+		clock-names = "ipg";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		tsc: tcq@50030400 {
+			compatible = "fsl,imx25-tcq";
+			reg = <0x50030400 0x60>;
+			...
+		};
+
+		adc: gcq@50030800 {
+			compatible = "fsl,imx25-gcq";
+			reg = <0x50030800 0x60>;
+			...
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/gateworks-gsc.yaml b/Documentation/devicetree/bindings/mfd/gateworks-gsc.yaml
new file mode 100644
index 000000000..d08e8fe76
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/gateworks-gsc.yaml
@@ -0,0 +1,200 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/gateworks-gsc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Gateworks System Controller
+
+description: |
+  The Gateworks System Controller (GSC) is a device present across various
+  Gateworks product families that provides a set of system related features
+  such as the following (refer to the board hardware user manuals to see what
+  features are present)
+   - Watchdog Timer
+   - GPIO
+   - Pushbutton controller
+   - Hardware monitor with ADC's for temperature and voltage rails and
+     fan controller
+
+maintainers:
+  - Tim Harvey <tharvey@gateworks.com>
+  - Robert Jones <rjones@gateworks.com>
+
+properties:
+  $nodename:
+    pattern: "gsc@[0-9a-f]{1,2}"
+  compatible:
+    const: gw,gsc
+
+  reg:
+    description: I2C device address
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  interrupt-controller: true
+
+  "#interrupt-cells":
+    const: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  adc:
+    type: object
+    description: Optional hardware monitoring module
+
+    properties:
+      compatible:
+        const: gw,gsc-adc
+
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+    patternProperties:
+      "^channel@[0-9]+$":
+        type: object
+        description: |
+          Properties for a single ADC which can report cooked values
+          (i.e. temperature sensor based on thermister), raw values
+          (i.e. voltage rail with a pre-scaling resistor divider).
+
+        properties:
+          reg:
+            description: Register of the ADC
+            maxItems: 1
+
+          label:
+            description: Name of the ADC input
+
+          gw,mode:
+            description: |
+              conversion mode:
+                0 - temperature, in C*10
+                1 - pre-scaled 24-bit voltage value
+                2 - scaled voltage based on an optional resistor divider
+                    and optional offset
+                3 - pre-scaled 16-bit voltage value
+            $ref: /schemas/types.yaml#/definitions/uint32
+            enum: [0, 1, 2, 3]
+
+          gw,voltage-divider-ohms:
+            description: Values of resistors for divider on raw ADC input
+            maxItems: 2
+            items:
+              minimum: 1000
+              maximum: 1000000
+
+          gw,voltage-offset-microvolt:
+            description: |
+              A positive voltage offset to apply to a raw ADC
+              (i.e. to compensate for a diode drop).
+            minimum: 0
+            maximum: 1000000
+
+        required:
+          - gw,mode
+          - reg
+          - label
+
+    required:
+      - compatible
+      - "#address-cells"
+      - "#size-cells"
+
+patternProperties:
+  "^fan-controller@[0-9a-f]+$":
+    type: object
+    description: Optional fan controller
+
+    properties:
+      compatible:
+        const: gw,gsc-fan
+
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+      reg:
+        description: The fan controller base address
+        maxItems: 1
+
+    required:
+      - compatible
+      - reg
+      - "#address-cells"
+      - "#size-cells"
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-controller
+  - "#interrupt-cells"
+  - "#address-cells"
+  - "#size-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        gsc@20 {
+            compatible = "gw,gsc";
+            reg = <0x20>;
+            interrupt-parent = <&gpio1>;
+            interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+            interrupt-controller;
+            #interrupt-cells = <1>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            adc {
+                compatible = "gw,gsc-adc";
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                channel@0 { /* A0: Board Temperature */
+                    reg = <0x00>;
+                    label = "temp";
+                    gw,mode = <0>;
+                };
+
+                channel@2 { /* A1: Input Voltage (raw ADC) */
+                    reg = <0x02>;
+                    label = "vdd_vin";
+                    gw,mode = <1>;
+                    gw,voltage-divider-ohms = <22100 1000>;
+                    gw,voltage-offset-microvolt = <800000>;
+                };
+
+                channel@b { /* A2: Battery voltage */
+                    reg = <0x0b>;
+                    label = "vdd_bat";
+                    gw,mode = <1>;
+                };
+            };
+
+            fan-controller@2c {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                compatible = "gw,gsc-fan";
+                reg = <0x2c>;
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mfd/google,cros-ec.yaml b/Documentation/devicetree/bindings/mfd/google,cros-ec.yaml
new file mode 100644
index 000000000..76bf16ee2
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/google,cros-ec.yaml
@@ -0,0 +1,193 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/google,cros-ec.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ChromeOS Embedded Controller
+
+maintainers:
+  - Benson Leung <bleung@chromium.org>
+  - Enric Balletbo i Serra <enric.balletbo@collabora.com>
+  - Guenter Roeck <groeck@chromium.org>
+
+description:
+  Google's ChromeOS EC is a microcontroller which talks to the AP and
+  implements various functions such as keyboard and battery charging.
+  The EC can be connected through various interfaces (I2C, SPI, and others)
+  and the compatible string specifies which interface is being used.
+
+properties:
+  compatible:
+    oneOf:
+      - description:
+          For implementations of the EC is connected through I2C.
+        const: google,cros-ec-i2c
+      - description:
+          For implementations of the EC is connected through SPI.
+        const: google,cros-ec-spi
+      - description:
+          For implementations of the EC is connected through RPMSG.
+        const: google,cros-ec-rpmsg
+
+  controller-data:
+    description:
+      SPI controller data, see bindings/spi/spi-samsung.txt
+    type: object
+
+  google,cros-ec-spi-pre-delay:
+    description:
+      This property specifies the delay in usecs between the
+      assertion of the CS and the first clock pulse.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - default: 0
+      - minimum: 0
+
+  google,cros-ec-spi-msg-delay:
+    description:
+      This property specifies the delay in usecs between messages.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - default: 0
+      - minimum: 0
+
+  google,has-vbc-nvram:
+    description:
+      Some implementations of the EC include a small nvram space used to
+      store verified boot context data. This boolean flag is used to specify
+      whether this nvram is present or not.
+    type: boolean
+
+  mtk,rpmsg-name:
+    description:
+      Must be defined if the cros-ec is a rpmsg device for a Mediatek
+      ARM Cortex M4 Co-processor. Contains the name pf the rpmsg
+      device. Used to match the subnode to the rpmsg device announced by
+      the SCP.
+    $ref: "/schemas/types.yaml#/definitions/string"
+
+  spi-max-frequency:
+    description: Maximum SPI frequency of the device in Hz.
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  wakeup-source:
+    description: Button can wake-up the system.
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  typec:
+    $ref: "/schemas/chrome/google,cros-ec-typec.yaml#"
+
+  ec-pwm:
+    $ref: "/schemas/pwm/google,cros-ec-pwm.yaml#"
+
+  keyboard-controller:
+    $ref: "/schemas/input/google,cros-ec-keyb.yaml#"
+
+  codecs:
+    type: object
+    additionalProperties: false
+
+    properties:
+      '#address-cells':
+        const: 2
+
+      '#size-cells':
+        const: 1
+
+    patternProperties:
+      "^ec-codec@[a-f0-9]+$":
+        type: object
+        $ref: "/schemas/sound/google,cros-ec-codec.yaml#"
+
+    required:
+      - "#address-cells"
+      - "#size-cells"
+
+patternProperties:
+  "^i2c-tunnel[0-9]*$":
+    type: object
+    $ref: "/schemas/i2c/google,cros-ec-i2c-tunnel.yaml#"
+
+  "^regulator@[0-9]+$":
+    type: object
+    $ref: "/schemas/regulator/google,cros-ec-regulator.yaml#"
+
+  "^extcon[0-9]*$":
+    type: object
+    $ref: "/schemas/extcon/extcon-usbc-cros-ec.yaml#"
+
+required:
+  - compatible
+
+if:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - google,cros-ec-i2c
+          - google,cros-ec-rpmsg
+then:
+  properties:
+    google,cros-ec-spi-pre-delay: false
+    google,cros-ec-spi-msg-delay: false
+    spi-max-frequency: false
+
+additionalProperties: false
+
+examples:
+  # Example for I2C
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        cros-ec@1e {
+            compatible = "google,cros-ec-i2c";
+            reg = <0x1e>;
+            interrupts = <6 0>;
+            interrupt-parent = <&gpio0>;
+        };
+    };
+
+  # Example for SPI
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    spi0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        cros-ec@0 {
+            compatible = "google,cros-ec-spi";
+            reg = <0x0>;
+            google,cros-ec-spi-msg-delay = <30>;
+            google,cros-ec-spi-pre-delay = <10>;
+            interrupts = <99 0>;
+            interrupt-parent = <&gpio7>;
+            spi-max-frequency = <5000000>;
+        };
+    };
+
+  # Example for RPMSG
+  - |
+    scp0 {
+        cros-ec {
+            compatible = "google,cros-ec-rpmsg";
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/mfd/hi6421.txt b/Documentation/devicetree/bindings/mfd/hi6421.txt
new file mode 100644
index 000000000..22da96d34
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/hi6421.txt
@@ -0,0 +1,40 @@
+* HI6421 Multi-Functional Device (MFD), by HiSilicon Ltd.
+
+Required parent device properties:
+- compatible    : One of the following chip-specific strings:
+	"hisilicon,hi6421-pmic";
+	"hisilicon,hi6421v530-pmic";
+- reg		: register range space of hi6421;
+
+Supported Hi6421 sub-devices include:
+
+Device                     IRQ Names              Supply Names   Description
+------                     ---------              ------------   -----------
+regulators               :  None                 : None         : Regulators
+
+Required child device properties:
+None.
+
+Example:
+	hi6421 {
+		compatible = "hisilicon,hi6421-pmic";
+		reg = <0xfcc00000 0x0180>; /* 0x60 << 2 */
+
+		regulators {
+			// supply for MLC NAND/ eMMC
+			hi6421_vout0_reg: hi6421_vout0 {
+				regulator-name = "VOUT0";
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <2850000>;
+			};
+
+			// supply for 26M Oscillator
+			hi6421_vout1_reg: hi6421_vout1 {
+				regulator-name = "VOUT1";
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt
new file mode 100644
index 000000000..9630ac0e4
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt
@@ -0,0 +1,33 @@
+Hisilicon Hi655x Power Management Integrated Circuit (PMIC)
+
+The hardware layout for access PMIC Hi655x from AP SoC Hi6220.
+Between PMIC Hi655x and Hi6220, the physical signal channel is SSI.
+We can use memory-mapped I/O to communicate.
+
++----------------+             +-------------+
+|                |             |             |
+|    Hi6220      |   SSI bus   |   Hi655x    |
+|                |-------------|             |
+|                |(REGMAP_MMIO)|             |
++----------------+             +-------------+
+
+Required properties:
+- compatible:           Should be "hisilicon,hi655x-pmic".
+- reg:                  Base address of PMIC on Hi6220 SoC.
+- interrupt-controller: Hi655x has internal IRQs (has own IRQ domain).
+- pmic-gpios:           The GPIO used by PMIC IRQ.
+- #clock-cells:		From common clock binding; shall be set to 0
+
+Optional properties:
+- clock-output-names: From common clock binding to override the
+  default output clock name
+
+Example:
+	pmic: pmic@f8000000 {
+		compatible = "hisilicon,hi655x-pmic";
+		reg = <0x0 0xf8000000 0x0 0x1000>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		#clock-cells = <0>;
+	}
diff --git a/Documentation/devicetree/bindings/mfd/iqs62x.yaml b/Documentation/devicetree/bindings/mfd/iqs62x.yaml
new file mode 100644
index 000000000..541b06d80
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/iqs62x.yaml
@@ -0,0 +1,179 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/iqs62x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Azoteq IQS620A/621/622/624/625 Multi-Function Sensors
+
+maintainers:
+  - Jeff LaBundy <jeff@labundy.com>
+
+description: |
+  The Azoteq IQS620A, IQS621, IQS622, IQS624 and IQS625 multi-function sensors
+  integrate multiple sensing technologies in a single package.
+
+  Link to datasheets: https://www.azoteq.com/
+
+properties:
+  compatible:
+    enum:
+      - azoteq,iqs620a
+      - azoteq,iqs621
+      - azoteq,iqs622
+      - azoteq,iqs624
+      - azoteq,iqs625
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  firmware-name:
+    $ref: /schemas/types.yaml#/definitions/string
+    description:
+      Specifies the name of the calibration and configuration file selected by
+      the driver. If this property is omitted, the name is chosen based on the
+      device name with ".bin" as the extension (e.g. iqs620a.bin for IQS620A).
+
+  keys:
+    $ref: ../input/iqs62x-keys.yaml
+
+  pwm:
+    $ref: ../pwm/iqs620a-pwm.yaml
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    /*
+     * Dual capacitive buttons with proximity-activated function, unipolar lid
+     * switch and panel-mounted LED.
+     */
+    #include <dt-bindings/input/input.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            iqs620a@44 {
+                    compatible = "azoteq,iqs620a";
+                    reg = <0x44>;
+                    interrupt-parent = <&gpio>;
+                    interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+
+                    keys {
+                            compatible = "azoteq,iqs620a-keys";
+
+                            linux,keycodes = <KEY_SELECT>,
+                                             <KEY_MENU>,
+                                             <KEY_OK>,
+                                             <KEY_MENU>;
+
+                            hall-switch-south {
+                                    linux,code = <SW_LID>;
+                                    azoteq,use-prox;
+                            };
+                    };
+
+                    iqs620a_pwm: pwm {
+                            compatible = "azoteq,iqs620a-pwm";
+                            #pwm-cells = <2>;
+                    };
+            };
+    };
+
+    pwmleds {
+            compatible = "pwm-leds";
+
+            panel {
+                    pwms = <&iqs620a_pwm 0 1000000>;
+                    max-brightness = <255>;
+            };
+    };
+
+  - |
+    /* Single inductive button with bipolar dock/tablet-mode switch. */
+    #include <dt-bindings/input/input.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            iqs620a@44 {
+                    compatible = "azoteq,iqs620a";
+                    reg = <0x44>;
+                    interrupt-parent = <&gpio>;
+                    interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+
+                    firmware-name = "iqs620a_coil.bin";
+
+                    keys {
+                            compatible = "azoteq,iqs620a-keys";
+
+                            linux,keycodes = <0>,
+                                             <0>,
+                                             <0>,
+                                             <0>,
+                                             <0>,
+                                             <0>,
+                                             <KEY_MUTE>;
+
+                            hall-switch-north {
+                                    linux,code = <SW_DOCK>;
+                            };
+
+                            hall-switch-south {
+                                    linux,code = <SW_TABLET_MODE>;
+                            };
+                    };
+            };
+    };
+
+  - |
+    /* Dual capacitive buttons with volume knob. */
+    #include <dt-bindings/input/input.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            iqs624@44 {
+                    compatible = "azoteq,iqs624";
+                    reg = <0x44>;
+                    interrupt-parent = <&gpio>;
+                    interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+
+                    keys {
+                            compatible = "azoteq,iqs624-keys";
+
+                            linux,keycodes = <BTN_0>,
+                                             <0>,
+                                             <BTN_1>,
+                                             <0>,
+                                             <0>,
+                                             <0>,
+                                             <0>,
+                                             <0>,
+                                             <0>,
+                                             <0>,
+                                             <0>,
+                                             <0>,
+                                             <0>,
+                                             <0>,
+                                             <KEY_VOLUMEUP>,
+                                             <KEY_VOLUMEDOWN>;
+                    };
+            };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mfd/khadas,mcu.yaml b/Documentation/devicetree/bindings/mfd/khadas,mcu.yaml
new file mode 100644
index 000000000..a3b976f10
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/khadas,mcu.yaml
@@ -0,0 +1,44 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/khadas,mcu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Khadas on-board Microcontroller Device Tree Bindings
+
+maintainers:
+  - Neil Armstrong <narmstrong@baylibre.com>
+
+description: |
+  Khadas embeds a microcontroller on their VIM and Edge boards adding some
+  system feature as PWM Fan control (for VIM2 rev14 or VIM3), User memory
+  storage, IR/Key resume control, system power LED control and more.
+
+properties:
+  compatible:
+    enum:
+      - khadas,mcu # MCU revision is discoverable
+
+  "#cooling-cells": # Only needed for boards having FAN control feature
+    const: 2
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      khadas_mcu: system-controller@18 {
+        compatible = "khadas,mcu";
+        reg = <0x18>;
+        #cooling-cells = <2>;
+      };
+    };
diff --git a/Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml b/Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml
new file mode 100644
index 000000000..eb3b43547
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml
@@ -0,0 +1,153 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/kontron,sl28cpld.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Kontron's sl28cpld board management controller
+
+maintainers:
+  - Michael Walle <michael@walle.cc>
+
+description: |
+  The board management controller may contain different IP blocks like
+  watchdog, fan monitoring, PWM controller, interrupt controller and a
+  GPIO controller.
+
+properties:
+  compatible:
+    const: kontron,sl28cpld
+
+  reg:
+    description:
+      I2C device address.
+    maxItems: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  "#interrupt-cells":
+    const: 2
+
+  interrupts:
+    maxItems: 1
+
+  interrupt-controller: true
+
+patternProperties:
+  "^gpio(@[0-9a-f]+)?$":
+    $ref: ../gpio/kontron,sl28cpld-gpio.yaml
+
+  "^hwmon(@[0-9a-f]+)?$":
+    $ref: ../hwmon/kontron,sl28cpld-hwmon.yaml
+
+  "^interrupt-controller(@[0-9a-f]+)?$":
+    $ref: ../interrupt-controller/kontron,sl28cpld-intc.yaml
+
+  "^pwm(@[0-9a-f]+)?$":
+    $ref: ../pwm/kontron,sl28cpld-pwm.yaml
+
+  "^watchdog(@[0-9a-f]+)?$":
+    $ref: ../watchdog/kontron,sl28cpld-wdt.yaml
+
+required:
+  - "#address-cells"
+  - "#size-cells"
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        sl28cpld@4a {
+            compatible = "kontron,sl28cpld";
+            reg = <0x4a>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            watchdog@4 {
+                compatible = "kontron,sl28cpld-wdt";
+                reg = <0x4>;
+                kontron,assert-wdt-timeout-pin;
+            };
+
+            hwmon@b {
+                compatible = "kontron,sl28cpld-fan";
+                reg = <0xb>;
+            };
+
+            pwm@c {
+                compatible = "kontron,sl28cpld-pwm";
+                reg = <0xc>;
+                #pwm-cells = <2>;
+            };
+
+            pwm@e {
+                compatible = "kontron,sl28cpld-pwm";
+                reg = <0xe>;
+                #pwm-cells = <2>;
+            };
+
+            gpio@10 {
+                compatible = "kontron,sl28cpld-gpio";
+                reg = <0x10>;
+                interrupts-extended = <&gpio2 6
+                               IRQ_TYPE_EDGE_FALLING>;
+
+                gpio-controller;
+                #gpio-cells = <2>;
+                gpio-line-names = "a", "b", "c";
+
+                interrupt-controller;
+                #interrupt-cells = <2>;
+            };
+
+            gpio@15 {
+                compatible = "kontron,sl28cpld-gpio";
+                reg = <0x15>;
+                interrupts-extended = <&gpio2 6
+                               IRQ_TYPE_EDGE_FALLING>;
+
+                gpio-controller;
+                #gpio-cells = <2>;
+
+                interrupt-controller;
+                #interrupt-cells = <2>;
+            };
+
+            gpio@1a {
+                compatible = "kontron,sl28cpld-gpo";
+                reg = <0x1a>;
+
+                gpio-controller;
+                #gpio-cells = <2>;
+            };
+
+            gpio@1b {
+                compatible = "kontron,sl28cpld-gpi";
+                reg = <0x1b>;
+
+                gpio-controller;
+                #gpio-cells = <2>;
+            };
+
+            interrupt-controller@1c {
+                compatible = "kontron,sl28cpld-intc";
+                reg = <0x1c>;
+                interrupts-extended = <&gpio2 6
+                               IRQ_TYPE_EDGE_FALLING>;
+
+                interrupt-controller;
+                #interrupt-cells = <2>;
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mfd/lp3943.txt b/Documentation/devicetree/bindings/mfd/lp3943.txt
new file mode 100644
index 000000000..e8591d6b1
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/lp3943.txt
@@ -0,0 +1,33 @@
+TI/National Semiconductor LP3943 MFD driver
+
+Required properties:
+  - compatible: "ti,lp3943"
+  - reg: I2C slave address. From 0x60 to 0x67.
+
+LP3943 consists of two sub-devices, lp3943-gpio and lp3943-pwm.
+
+For the LP3943 GPIO properties please refer to:
+Documentation/devicetree/bindings/gpio/gpio-lp3943.txt
+
+For the LP3943 PWM properties please refer to:
+Documentation/devicetree/bindings/pwm/pwm-lp3943.txt
+
+Example:
+
+lp3943@60 {
+	compatible = "ti,lp3943";
+	reg = <0x60>;
+
+	gpioex: gpio {
+		compatible = "ti,lp3943-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pwm3943: pwm {
+		compatible = "ti,lp3943-pwm";
+		#pwm-cells = <2>;
+		ti,pwm0 = <8 9 10>;
+		ti,pwm1 = <15>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/lp873x.txt b/Documentation/devicetree/bindings/mfd/lp873x.txt
new file mode 100644
index 000000000..ae9cf39bd
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/lp873x.txt
@@ -0,0 +1,67 @@
+TI LP873X PMIC MFD driver
+
+Required properties:
+  - compatible:	"ti,lp8732", "ti,lp8733"
+  - reg:		I2C slave address.
+  - gpio-controller:	Marks the device node as a GPIO Controller.
+  - #gpio-cells:	Should be two.  The first cell is the pin number and
+			the second cell is used to specify flags.
+			See ../gpio/gpio.txt for more information.
+  - xxx-in-supply:	Phandle to parent supply node of each regulator
+			populated under regulators node. xxx can be
+			buck0, buck1, ldo0 or ldo1.
+  - regulators:	List of child nodes that specify the regulator
+			initialization data.
+Example:
+
+pmic: lp8733@60 {
+	compatible = "ti,lp8733";
+	reg = <0x60>;
+	gpio-controller;
+	#gpio-cells = <2>;
+
+	buck0-in-supply = <&vsys_3v3>;
+	buck1-in-supply = <&vsys_3v3>;
+	ldo0-in-supply = <&vsys_3v3>;
+	ldo1-in-supply = <&vsys_3v3>;
+
+	regulators {
+		lp8733_buck0: buck0 {
+			regulator-name = "lp8733-buck0";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1400000>;
+			regulator-min-microamp = <1500000>;
+			regulator-max-microamp = <4000000>;
+			regulator-ramp-delay = <10000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		lp8733_buck1: buck1 {
+			regulator-name = "lp8733-buck1";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1400000>;
+			regulator-min-microamp = <1500000>;
+			regulator-max-microamp = <4000000>;
+			regulator-ramp-delay = <10000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		lp8733_ldo0: ldo0 {
+			regulator-name = "lp8733-ldo0";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		lp8733_ldo1: ldo1 {
+			regulator-name = "lp8733-ldo1";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/max14577.txt b/Documentation/devicetree/bindings/mfd/max14577.txt
new file mode 100644
index 000000000..92070b346
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max14577.txt
@@ -0,0 +1,147 @@
+Maxim MAX14577/77836 Multi-Function Device
+
+MAX14577 is a Multi-Function Device with Micro-USB Interface Circuit, Li+
+Battery Charger and SFOUT LDO output for powering USB devices. It is
+interfaced to host controller using I2C.
+
+MAX77836 additionally contains PMIC (with two LDO regulators) and Fuel Gauge.
+For the description of Fuel Gauge low SOC alert interrupt see:
+../power/supply/max17040_battery.txt
+
+
+Required properties:
+- compatible : Must be "maxim,max14577" or "maxim,max77836".
+- reg : I2C slave address for the max14577 chip (0x25 for max14577/max77836)
+- interrupts : IRQ line for the chip.
+
+
+Required nodes:
+ - charger :
+	Node for configuring the charger driver.
+	Required properties:
+		- compatible : "maxim,max14577-charger"
+			or "maxim,max77836-charger"
+		- maxim,fast-charge-uamp : Current in uA for Fast Charge;
+			Valid values:
+			- for max14577: 90000 - 950000;
+			- for max77836: 45000 - 475000;
+		- maxim,eoc-uamp : Current in uA for End-Of-Charge mode;
+			Valid values:
+			- for max14577: 50000 - 200000;
+			- for max77836: 5000 - 100000;
+		- maxim,ovp-uvolt : OverVoltage Protection Threshold in uV;
+			In an overvoltage condition, INT asserts and charging
+			stops. Valid values:
+			- 6000000, 6500000, 7000000, 7500000;
+		- maxim,constant-uvolt : Battery Constant Voltage in uV;
+			Valid values:
+			- 4000000 - 4280000 (step by 20000);
+			- 4350000;
+
+
+Optional nodes:
+- max14577-muic/max77836-muic :
+	Node used only by extcon consumers.
+	Required properties:
+		- compatible : "maxim,max14577-muic" or "maxim,max77836-muic"
+
+- regulators :
+	Required properties:
+		- compatible : "maxim,max14577-regulator"
+			or "maxim,max77836-regulator"
+
+	May contain a sub-node per regulator from the list below. Each
+	sub-node should contain the constraints and initialization information
+	for that regulator. See regulator.txt for a description of standard
+	properties for these sub-nodes.
+
+	List of valid regulator names:
+	- for max14577: CHARGER, SAFEOUT.
+	- for max77836: CHARGER, SAFEOUT, LDO1, LDO2.
+
+	The SAFEOUT is a fixed voltage regulator so there is no need to specify
+	voltages for it.
+
+
+Example:
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+max14577@25 {
+	compatible = "maxim,max14577";
+	reg = <0x25>;
+	interrupt-parent = <&gpx1>;
+	interrupts = <5 IRQ_TYPE_NONE>;
+
+	muic: max14577-muic {
+		compatible = "maxim,max14577-muic";
+	};
+
+	regulators {
+		compatible = "maxim,max14577-regulator";
+
+		SAFEOUT {
+			regulator-name = "SAFEOUT";
+		};
+		CHARGER {
+			regulator-name = "CHARGER";
+			regulator-min-microamp = <90000>;
+			regulator-max-microamp = <950000>;
+			regulator-boot-on;
+		};
+	};
+
+	charger {
+		compatible = "maxim,max14577-charger";
+
+		maxim,constant-uvolt = <4350000>;
+		maxim,fast-charge-uamp = <450000>;
+		maxim,eoc-uamp = <50000>;
+		maxim,ovp-uvolt = <6500000>;
+	};
+};
+
+
+max77836@25 {
+	compatible = "maxim,max77836";
+	reg = <0x25>;
+	interrupt-parent = <&gpx1>;
+	interrupts = <5 IRQ_TYPE_NONE>;
+
+	muic: max77836-muic {
+		compatible = "maxim,max77836-muic";
+	};
+
+	regulators {
+		compatible = "maxim,max77836-regulator";
+
+		SAFEOUT {
+			regulator-name = "SAFEOUT";
+		};
+		CHARGER {
+			regulator-name = "CHARGER";
+			regulator-min-microamp = <90000>;
+			regulator-max-microamp = <950000>;
+			regulator-boot-on;
+		};
+		LDO1 {
+			regulator-name = "LDO1";
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+		LDO2 {
+			regulator-name = "LDO2";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <3950000>;
+		};
+	};
+
+	charger {
+		compatible = "maxim,max77836-charger";
+
+		maxim,constant-uvolt = <4350000>;
+		maxim,fast-charge-uamp = <225000>;
+		maxim,eoc-uamp = <7500>;
+		maxim,ovp-uvolt = <6500000>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/max77620.txt b/Documentation/devicetree/bindings/mfd/max77620.txt
new file mode 100644
index 000000000..5a642a51d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max77620.txt
@@ -0,0 +1,162 @@
+MAX77620 Power management IC from Maxim Semiconductor.
+
+Required properties:
+-------------------
+- compatible: Must be one of
+		"maxim,max77620"
+		"maxim,max20024"
+		"maxim,max77663"
+- reg: I2C device address.
+
+Optional properties:
+-------------------
+- interrupts:		The interrupt on the parent the controller is
+			connected to.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells:	is <2> and their usage is compliant to the 2 cells
+			variant of <../interrupt-controller/interrupts.txt>
+			IRQ numbers for different interrupt source of MAX77620
+			are defined at dt-bindings/mfd/max77620.h.
+
+- system-power-controller: Indicates that this PMIC is controlling the
+			   system power, see [1] for more details.
+
+[1] Documentation/devicetree/bindings/power/power-controller.txt
+
+Optional subnodes and their properties:
+=======================================
+
+Flexible power sequence configurations:
+--------------------------------------
+The Flexible Power Sequencer (FPS) allows each regulator to power up under
+hardware or software control. Additionally, each regulator can power on
+independently or among a group of other regulators with an adjustable power-up
+and power-down delays (sequencing). GPIO1, GPIO2, and GPIO3 can be programmed
+to be part of a sequence allowing external regulators to be sequenced along
+with internal regulators. 32KHz clock can be programmed to be part of a
+sequence.
+
+The flexible sequencing structure consists of two hardware enable inputs
+(EN0, EN1), and 3 master sequencing timers called FPS0, FPS1 and FPS2.
+Each master sequencing timer is programmable through its configuration
+register to have a hardware enable source (EN1 or EN2) or a software enable
+source (SW). When enabled/disabled, the master sequencing timer generates
+eight sequencing events on different time periods called slots. The time
+period between each event is programmable within the configuration register.
+Each regulator, GPIO1, GPIO2, GPIO3, and 32KHz clock has a flexible power
+sequence slave register which allows its enable source to be specified as
+a flexible power sequencer timer or a software bit. When a FPS source of
+regulators, GPIOs and clocks specifies the enable source to be a flexible
+power sequencer, the power up and power down delays can be specified in
+the regulators, GPIOs and clocks flexible power sequencer configuration
+registers.
+
+When FPS event cleared (set to LOW), regulators, GPIOs and 32KHz
+clock are set into following state at the sequencing event that
+corresponds to its flexible sequencer configuration register.
+	Sleep state: 			In this state, regulators, GPIOs
+					and 32KHz clock get disabled at
+					the sequencing event.
+	Global Low Power Mode (GLPM):	In this state, regulators are set in
+					low power mode at the sequencing event.
+
+The configuration parameters of FPS is provided through sub-node "fps"
+and their child for FPS specific. The child node name for FPS are "fps0",
+"fps1", and "fps2" for FPS0, FPS1 and FPS2 respectively.
+
+The FPS configurations like FPS source, power up and power down slots for
+regulators, GPIOs and 32kHz clocks are provided in their respective
+configuration nodes which is explained in respective sub-system DT
+binding document.
+
+There is need for different FPS configuration parameters based on system
+state like when system state changed from active to suspend or active to
+power off (shutdown).
+
+Optional properties:
+-------------------
+-maxim,fps-event-source:		u32, FPS event source like external
+					hardware input to PMIC i.e. EN0, EN1 or
+					software (SW).
+					The macros are defined on
+						dt-bindings/mfd/max77620.h
+					for different control source.
+					- MAX77620_FPS_EVENT_SRC_EN0
+						for hardware input pin EN0.
+					- MAX77620_FPS_EVENT_SRC_EN1
+						for hardware input pin EN1.
+					- MAX77620_FPS_EVENT_SRC_SW
+						for software control.
+
+-maxim,shutdown-fps-time-period-us:	u32, FPS time period in microseconds
+					when system enters in to shutdown
+					state.
+
+-maxim,suspend-fps-time-period-us:	u32, FPS time period in microseconds
+					when system enters in to suspend state.
+
+-maxim,device-state-on-disabled-event:	u32, describe the PMIC state when FPS
+					event cleared (set to LOW) whether it
+					should go to sleep state or low-power
+					state. Following are valid values:
+					- MAX77620_FPS_INACTIVE_STATE_SLEEP
+						to set the PMIC state to sleep.
+					- MAX77620_FPS_INACTIVE_STATE_LOW_POWER
+						to set the PMIC state to low
+						power.
+					Absence of this property or other value
+					will not change device state when FPS
+					event get cleared.
+
+Here supported time periods by device in microseconds are as follows:
+MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds.
+MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds.
+MAX77663 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds.
+
+-maxim,power-ok-control: configure map power ok bit
+			1: Enables POK(Power OK) to control nRST_IO and GPIO1
+			POK function.
+			0: Disables POK control.
+			if property missing, do not configure MPOK bit.
+			If POK mapping is enabled for GPIO1/nRST_IO then,
+			GPIO1/nRST_IO pins are HIGH only if all rails
+			that have POK control enabled are HIGH.
+			If any of the rails goes down(which are enabled for POK
+			control) then, GPIO1/nRST_IO goes LOW.
+			this property is valid for max20024 only.
+
+For DT binding details of different sub modules like GPIO, pincontrol,
+regulator, power, please refer respective device-tree binding document
+under their respective sub-system directories.
+
+Example:
+--------
+#include <dt-bindings/mfd/max77620.h>
+
+max77620@3c {
+	compatible = "maxim,max77620";
+	reg = <0x3c>;
+
+	interrupt-parent = <&intc>;
+	interrupts = <0 86 IRQ_TYPE_NONE>;
+
+	interrupt-controller;
+	#interrupt-cells = <2>;
+
+	fps {
+		fps0 {
+			maxim,shutdown-fps-time-period-us = <1280>;
+			maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>;
+		};
+
+		fps1 {
+			maxim,shutdown-fps-time-period-us = <1280>;
+			maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+		};
+
+		fps2 {
+			maxim,shutdown-fps-time-period-us = <1280>;
+			maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_SW>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/max77650.yaml b/Documentation/devicetree/bindings/mfd/max77650.yaml
new file mode 100644
index 000000000..b0a0f0d3d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max77650.yaml
@@ -0,0 +1,151 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/max77650.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MAX77650 ultra low-power PMIC from Maxim Integrated.
+
+maintainers:
+  - Bartosz Golaszewski <bgolaszewski@baylibre.com>
+
+description: |
+  MAX77650 is an ultra-low power PMIC providing battery charging and power
+  supply for low-power IoT and wearable applications.
+
+  The GPIO-controller module is represented as part of the top-level PMIC
+  node. The device exposes a single GPIO line.
+
+  For device-tree bindings of other sub-modules (regulator, power supply,
+  LEDs and onkey) refer to the binding documents under the respective
+  sub-system directories.
+
+properties:
+  compatible:
+    const: maxim,max77650
+
+  reg:
+    description:
+      I2C device address.
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  interrupt-controller: true
+
+  "#interrupt-cells":
+    const: 2
+    description:
+      The first cell is the IRQ number, the second cell is the trigger type.
+
+  gpio-controller: true
+
+  "#gpio-cells":
+    const: 2
+    description:
+      The first cell is the pin number and the second cell is used to specify
+      the gpio active state.
+
+  gpio-line-names:
+    maxItems: 1
+    description:
+      Single string containing the name of the GPIO line.
+
+  regulators:
+    $ref: ../regulator/max77650-regulator.yaml
+
+  charger:
+    $ref: ../power/supply/max77650-charger.yaml
+
+  leds:
+    $ref: ../leds/leds-max77650.yaml
+
+  onkey:
+    $ref: ../input/max77650-onkey.yaml
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-controller
+  - "#interrupt-cells"
+  - gpio-controller
+  - "#gpio-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/input/linux-event-codes.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pmic@48 {
+            compatible = "maxim,max77650";
+            reg = <0x48>;
+
+            interrupt-controller;
+            interrupt-parent = <&gpio2>;
+            #interrupt-cells = <2>;
+            interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+            gpio-controller;
+            #gpio-cells = <2>;
+            gpio-line-names = "max77650-charger";
+
+            regulators {
+                compatible = "maxim,max77650-regulator";
+
+                max77650_ldo: regulator-ldo {
+                    regulator-compatible = "ldo";
+                    regulator-name = "max77650-ldo";
+                    regulator-min-microvolt = <1350000>;
+                    regulator-max-microvolt = <2937500>;
+                };
+
+                max77650_sbb0: regulator-sbb0 {
+                    regulator-compatible = "sbb0";
+                    regulator-name = "max77650-sbb0";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <1587500>;
+                };
+            };
+
+            charger {
+                compatible = "maxim,max77650-charger";
+                input-voltage-min-microvolt = <4200000>;
+                input-current-limit-microamp = <285000>;
+            };
+
+            leds {
+                compatible = "maxim,max77650-led";
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                led@0 {
+                    reg = <0>;
+                    label = "blue:usr0";
+                };
+
+                led@1 {
+                    reg = <1>;
+                    label = "red:usr1";
+                    linux,default-trigger = "heartbeat";
+                };
+
+                led@2 {
+                    reg = <2>;
+                    label = "green:usr2";
+                };
+            };
+
+            onkey {
+                compatible = "maxim,max77650-onkey";
+                linux,code = <KEY_END>;
+                maxim,onkey-slide;
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt
new file mode 100644
index 000000000..42968b714
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max77686.txt
@@ -0,0 +1,26 @@
+Maxim MAX77686 multi-function device
+
+MAX77686 is a Multifunction device with PMIC, RTC and Charger on chip. It is
+interfaced to host controller using i2c interface. PMIC and Charger submodules
+are addressed using same i2c slave address whereas RTC submodule uses
+different i2c slave address,presently for which we are statically creating i2c
+client while probing.This document describes the binding for mfd device and
+PMIC submodule.
+
+Bindings for the built-in 32k clock generator block and
+regulators are defined in ../clk/maxim,max77686.txt and
+../regulator/max77686.txt respectively.
+
+Required properties:
+- compatible : Must be "maxim,max77686";
+- reg : Specifies the i2c slave address of PMIC block.
+- interrupts : This i2c device has an IRQ line connected to the main SoC.
+
+Example:
+
+	max77686: pmic@9 {
+		compatible = "maxim,max77686";
+		interrupt-parent = <&wakeup_eint>;
+		interrupts = <26 0>;
+		reg = <0x09>;
+	};
diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
new file mode 100644
index 000000000..0ced96e16
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max77693.txt
@@ -0,0 +1,194 @@
+Maxim MAX77693 multi-function device
+
+MAX77693 is a Multifunction device with the following submodules:
+- PMIC,
+- CHARGER,
+- LED,
+- MUIC,
+- HAPTIC
+
+It is interfaced to host controller using i2c.
+This document describes the bindings for the mfd device.
+
+Required properties:
+- compatible : Must be "maxim,max77693".
+- reg : Specifies the i2c slave address of PMIC block.
+- interrupts : This i2c device has an IRQ line connected to the main SoC.
+
+Optional properties:
+- regulators : The regulators of max77693 have to be instantiated under subnode
+  named "regulators" using the following format.
+
+	regulators {
+		regulator-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER
+		standard regulator constraints[*].
+	};
+
+	[*] refer Documentation/devicetree/bindings/regulator/regulator.txt
+
+- haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide
+  users with tactile feedback. PWM period and duty-cycle are varied in
+  order to provide the appropriate level of feedback.
+
+ Required properties:
+	- compatible : Must be "maxim,max77693-haptic"
+	- haptic-supply : power supply for the haptic motor
+	[*] refer Documentation/devicetree/bindings/regulator/regulator.txt
+	- pwms : phandle to the physical PWM(Pulse Width Modulation) device.
+	 PWM properties should be named "pwms". And number of cell is different
+	 for each pwm device.
+	 To get more information, please refer to documentation.
+	[*] refer Documentation/devicetree/bindings/pwm/pwm.txt
+
+- charger : Node configuring the charger driver.
+  If present, required properties:
+  - compatible : Must be "maxim,max77693-charger".
+
+  Optional properties (if not set, defaults will be used):
+  - maxim,constant-microvolt : Battery constant voltage in uV. The charger
+    will operate in fast charge constant current mode till battery voltage
+    reaches this level. Then the charger will switch to fast charge constant
+    voltage mode. Also vsys (system voltage) will be set to this value when
+    DC power is supplied but charger is not enabled.
+    Valid values: 3650000 - 4400000, step by 25000 (rounded down)
+    Default: 4200000
+
+  - maxim,min-system-microvolt : Minimal system voltage in uV.
+    Valid values: 3000000 - 3700000, step by 100000 (rounded down)
+    Default: 3600000
+
+  - maxim,thermal-regulation-celsius : Temperature in Celsius for entering
+    high temperature charging mode. If die temperature exceeds this value
+    the charging current will be reduced by 105 mA/Celsius.
+    Valid values: 70, 85, 100, 115
+    Default: 100
+
+  - maxim,battery-overcurrent-microamp : Overcurrent protection threshold
+    in uA (current from battery to system).
+    Valid values: 2000000 - 3500000, step by 250000 (rounded down)
+    Default: 3500000
+
+  - maxim,charge-input-threshold-microvolt : Threshold voltage in uV for
+    triggering input voltage regulation loop. If input voltage decreases
+    below this value, the input current will be reduced to reach the
+    threshold voltage.
+    Valid values: 4300000, 4700000, 4800000, 4900000
+    Default: 4300000
+
+- led : the LED submodule device node
+
+There are two LED outputs available - FLED1 and FLED2. Each of them can
+control a separate LED or they can be connected together to double
+the maximum current for a single connected LED. One LED is represented
+by one child node.
+
+Required properties:
+- compatible : Must be "maxim,max77693-led".
+
+Optional properties:
+- maxim,boost-mode :
+	In boost mode the device can produce up to 1.2A of total current
+	on both outputs. The maximum current on each output is reduced
+	to 625mA then. If not enabled explicitly, boost setting defaults to
+	LEDS_BOOST_FIXED in case both current sources are used.
+	Possible values:
+		LEDS_BOOST_OFF (0) - no boost,
+		LEDS_BOOST_ADAPTIVE (1) - adaptive mode,
+		LEDS_BOOST_FIXED (2) - fixed mode.
+- maxim,boost-mvout : Output voltage of the boost module in millivolts.
+	Valid values: 3300 - 5500, step by 25 (rounded down)
+	Default: 3300
+- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired
+	if chip estimates that system voltage could drop below this level due
+	to flash power consumption.
+	Valid values: 2400 - 3400, step by 33 (rounded down)
+	Default: 2400
+
+Required properties for the LED child node:
+- led-sources : see Documentation/devicetree/bindings/leds/common.txt;
+		device current output identifiers: 0 - FLED1, 1 - FLED2
+- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+	Valid values for a LED connected to one FLED output:
+		15625 - 250000, step by 15625 (rounded down)
+	Valid values for a LED connected to both FLED outputs:
+		15625 - 500000, step by 15625 (rounded down)
+- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+	Valid values for a single LED connected to one FLED output
+	(boost mode must be turned off):
+		15625 - 1000000, step by 15625 (rounded down)
+	Valid values for a single LED connected to both FLED outputs:
+		15625 - 1250000, step by 15625 (rounded down)
+	Valid values for two LEDs case:
+		15625 - 625000, step by 15625 (rounded down)
+- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
+	Valid values: 62500 - 1000000, step by 62500 (rounded down)
+
+Optional properties for the LED child node:
+- label : see Documentation/devicetree/bindings/leds/common.txt
+
+Optional nodes:
+- max77693-muic :
+	Node used only by extcon consumers.
+	Required properties:
+		- compatible : "maxim,max77693-muic"
+
+Example:
+#include <dt-bindings/leds/common.h>
+
+	max77693@66 {
+		compatible = "maxim,max77693";
+		reg = <0x66>;
+		interrupt-parent = <&gpx1>;
+		interrupts = <5 2>;
+
+		regulators {
+			esafeout@1 {
+				regulator-compatible = "ESAFEOUT1";
+				regulator-name = "ESAFEOUT1";
+				regulator-boot-on;
+			};
+			esafeout@2 {
+				regulator-compatible = "ESAFEOUT2";
+				regulator-name = "ESAFEOUT2";
+				};
+			charger@0 {
+				regulator-compatible = "CHARGER";
+				regulator-name = "CHARGER";
+				regulator-min-microamp = <60000>;
+				regulator-max-microamp = <2580000>;
+					regulator-boot-on;
+			};
+		};
+
+		haptic {
+			compatible = "maxim,max77693-haptic";
+			haptic-supply = <&haptic_supply>;
+			pwms = <&pwm 0 40000 0>;
+			pwm-names = "haptic";
+		};
+
+		charger {
+			compatible = "maxim,max77693-charger";
+
+			maxim,constant-microvolt = <4200000>;
+			maxim,min-system-microvolt = <3600000>;
+			maxim,thermal-regulation-celsius = <75>;
+			maxim,battery-overcurrent-microamp = <3000000>;
+			maxim,charge-input-threshold-microvolt = <4300000>;
+		};
+
+		led {
+			compatible = "maxim,max77693-led";
+			maxim,boost-mode = <LEDS_BOOST_FIXED>;
+			maxim,boost-mvout = <5000>;
+			maxim,mvsys-min = <2400>;
+
+			camera_flash: flash-led {
+				label = "max77693-flash";
+				led-sources = <0>, <1>;
+				led-max-microamp = <500000>;
+				flash-max-microamp = <1250000>;
+				flash-max-timeout-us = <1000000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/max77802.txt b/Documentation/devicetree/bindings/mfd/max77802.txt
new file mode 100644
index 000000000..09decac20
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max77802.txt
@@ -0,0 +1,25 @@
+Maxim MAX77802 multi-function device
+
+The Maxim MAX77802 is a Power Management IC (PMIC) that contains 10 high
+efficiency Buck regulators, 32 Low-DropOut (LDO) regulators used to power
+up application processors and peripherals, a 2-channel 32kHz clock outputs,
+a Real-Time-Clock (RTC) and a I2C interface to program the individual
+regulators, clocks outputs and the RTC.
+
+Bindings for the built-in 32k clock generator block and
+regulators are defined in ../clk/maxim,max77802.txt and
+../regulator/max77802.txt respectively.
+
+Required properties:
+- compatible		: Must be "maxim,max77802"
+- reg			: Specifies the I2C slave address of PMIC block.
+- interrupts		: I2C device IRQ line connected to the main SoC.
+
+Example:
+
+	max77802: pmic@9 {
+		compatible = "maxim,max77802";
+		interrupt-parent = <&intc>;
+		interrupts = <26 IRQ_TYPE_NONE>;
+		reg = <0x09>;
+	};
diff --git a/Documentation/devicetree/bindings/mfd/max8925.txt b/Documentation/devicetree/bindings/mfd/max8925.txt
new file mode 100644
index 000000000..4f0dc6638
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max8925.txt
@@ -0,0 +1,64 @@
+* Maxim max8925 Power Management IC
+
+Required parent device properties:
+- compatible : "maxim,max8925"
+- reg : the I2C slave address for the max8925 chip
+- interrupts : IRQ line for the max8925 chip
+- interrupt-controller: describes the max8925 as an interrupt
+  controller (has its own domain)
+- #interrupt-cells : should be 1.
+	- The cell is the max8925 local IRQ number
+
+Optional parent device properties:
+- maxim,tsc-irq: there are 2 IRQ lines for max8925, one is indicated in
+  interrupts property, the other is indicated here.
+
+max8925 consists of a large and varied group of sub-devices:
+
+Device			 Supply Names	 Description
+------			 ------------	 -----------
+max8925-onkey		:		: On key
+max8925-rtc		:		: RTC
+max8925-regulator	:		: Regulators
+max8925-backlight	:		: Backlight
+max8925-touch		:		: Touchscreen
+max8925-power		:		: Charger
+
+Example:
+
+	pmic: max8925@3c {
+		compatible = "maxim,max8925";
+		reg = <0x3c>;
+		interrupts = <1>;
+		interrupt-parent = <&intcmux4>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		maxim,tsc-irq = <0>;
+
+		regulators {
+			SDV1 {
+				regulator-min-microvolt = <637500>;
+				regulator-max-microvolt = <1425000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO1 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+		};
+		backlight {
+			maxim,max8925-dual-string = <0>;
+		};
+		charger {
+			batt-detect = <0>;
+			topoff-threshold = <1>;
+			fast-charge = <7>;
+			no-temp-support = <0>;
+			no-insert-detect = <0>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/max8998.txt b/Documentation/devicetree/bindings/mfd/max8998.txt
new file mode 100644
index 000000000..4ed52184d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max8998.txt
@@ -0,0 +1,125 @@
+* Maxim MAX8998, National/TI LP3974 multi-function device
+
+The Maxim MAX8998 is a multi-function device which includes voltage/current
+regulators, real time clock, battery charging controller and several
+other sub-blocks. It is interfaced using an I2C interface. Each sub-block
+is addressed by the host system using different i2c slave address.
+
+PMIC sub-block
+--------------
+
+The PMIC sub-block contains a number of voltage and current regulators,
+with controllable parameters and dynamic voltage scaling capability.
+In addition, it includes a real time clock and battery charging controller
+as well. It is accessible at I2C address 0x66.
+
+Required properties:
+- compatible: Should be one of the following:
+    - "maxim,max8998" for Maxim MAX8998
+    - "national,lp3974" or "ti,lp3974" for National/TI LP3974.
+- reg: Specifies the i2c slave address of the pmic block. It should be 0x66.
+
+Optional properties:
+- interrupts: Interrupt specifiers for two interrupt sources.
+  - First interrupt specifier is for main interrupt.
+  - Second interrupt specifier is for power-on/-off interrupt.
+- max8998,pmic-buck1-dvs-gpios: GPIO specifiers for two host gpios used
+  for buck 1 dvs. The format of the gpio specifier depends on the gpio
+  controller.
+- max8998,pmic-buck2-dvs-gpio: GPIO specifier for host gpio used
+  for buck 2 dvs. The format of the gpio specifier depends on the gpio
+  controller.
+- max8998,pmic-buck1-default-dvs-idx: Default voltage setting selected from
+  the possible 4 options selectable by the dvs gpios. The value of this
+  property should be 0, 1, 2 or 3. If not specified or out of range,
+  a default value of 0 is taken.
+- max8998,pmic-buck2-default-dvs-idx: Default voltage setting selected from
+  the possible 2 options selectable by the dvs gpios. The value of this
+  property should be 0 or 1. If not specified or out of range, a default
+  value of 0 is taken.
+- max8998,pmic-buck-voltage-lock: If present, disallows changing of
+  preprogrammed buck dvfs voltages.
+
+Additional properties required if max8998,pmic-buck1-dvs-gpios is defined:
+- max8998,pmic-buck1-dvs-voltage: An array of 4 voltage values in microvolts
+  for buck1 regulator that can be selected using dvs gpio.
+
+Additional properties required if max8998,pmic-buck2-dvs-gpio is defined:
+- max8998,pmic-buck2-dvs-voltage: An array of 2 voltage values in microvolts
+  for buck2 regulator that can be selected using dvs gpio.
+
+Regulators: All the regulators of MAX8998 to be instantiated shall be
+listed in a child node named 'regulators'. Each regulator is represented
+by a child node of the 'regulators' node.
+
+	regulator-name {
+		/* standard regulator bindings here */
+	};
+
+Following regulators of the MAX8998 PMIC block are supported. Note that
+the 'n' in regulator name, as in LDOn or BUCKn, represents the LDO or BUCK
+number as described in MAX8998 datasheet.
+
+	- LDOn
+		  - valid values for n are 2 to 17
+		  - Example: LDO2, LDO10, LDO17
+	- BUCKn
+		  - valid values for n are 1 to 4.
+		  - Example: BUCK1, BUCK2, BUCK3, BUCK4
+
+	- ENVICHG: Battery Charging Current Monitor Output. This is a fixed
+		   voltage type regulator
+
+	- ESAFEOUT1: (ldo19)
+	- ESAFEOUT2: (ld020)
+
+	- CHARGER: main battery charger current control
+
+Standard regulator bindings are used inside regulator subnodes. Check
+  Documentation/devicetree/bindings/regulator/regulator.txt
+for more details.
+
+Example:
+
+	pmic@66 {
+		compatible = "maxim,max8998-pmic";
+		reg = <0x66>;
+		interrupt-parent = <&wakeup_eint>;
+		interrupts = <4 0>, <3 0>;
+
+		/* Buck 1 DVS settings */
+		max8998,pmic-buck1-default-dvs-idx = <0>;
+		max8998,pmic-buck1-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */
+					       <&gpx0 1 1 0 0>; /* SET2 */
+		max8998,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
+						 <1000000>, <950000>;
+
+		/* Buck 2 DVS settings */
+		max8998,pmic-buck2-default-dvs-idx = <0>;
+		max8998,pmic-buck2-dvs-gpio = <&gpx0 0 3 0 0>; /* SET3 */
+		max8998,pmic-buck2-dvs-voltage = <1350000>, <1300000>;
+
+		/* Regulators to instantiate */
+		regulators {
+			ldo2_reg: LDO2 {
+				regulator-name = "VDD_ALIVE_1.1V";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "VDD_ARM_1.2V";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			charger_reg: CHARGER {
+				regulator-name = "CHARGER";
+				regulator-min-microamp = <90000>;
+				regulator-max-microamp = <800000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt
new file mode 100644
index 000000000..8261ea732
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt
@@ -0,0 +1,156 @@
+* Freescale MC13783/MC13892 Power Management Integrated Circuit (PMIC)
+
+Required properties:
+- compatible : Should be "fsl,mc13783" or "fsl,mc13892"
+
+Optional properties:
+- fsl,mc13xxx-uses-adc : Indicate the ADC is being used
+- fsl,mc13xxx-uses-codec : Indicate the Audio Codec is being used
+- fsl,mc13xxx-uses-rtc : Indicate the RTC is being used
+- fsl,mc13xxx-uses-touch : Indicate the touchscreen controller is being used
+
+Sub-nodes:
+- codec: Contain the Audio Codec node.
+  - adc-port: Contain PMIC SSI port number used for ADC.
+  - dac-port: Contain PMIC SSI port number used for DAC.
+- leds : Contain the led nodes and initial register values in property
+  "led-control". Number of register depends of used IC, for MC13783 is 6,
+  for MC13892 is 4, for MC34708 is 1. See datasheet for bits definitions of
+  these registers.
+  - #address-cells: Must be 1.
+  - #size-cells: Must be 0.
+  Each led node should contain "reg", which used as LED ID (described below).
+  Optional properties "label" and "linux,default-trigger" is described in
+  Documentation/devicetree/bindings/leds/common.txt.
+- regulators : Contain the regulator nodes. The regulators are bound using
+  their names as listed below with their registers and bits for enabling.
+
+MC13783 LED IDs:
+    0  : Main display
+    1  : AUX display
+    2  : Keypad
+    3  : Red 1
+    4  : Green 1
+    5  : Blue 1
+    6  : Red 2
+    7  : Green 2
+    8  : Blue 2
+    9  : Red 3
+    10 : Green 3
+    11 : Blue 3
+
+MC13892 LED IDs:
+    0  : Main display
+    1  : AUX display
+    2  : Keypad
+    3  : Red
+    4  : Green
+    5  : Blue
+
+MC34708 LED IDs:
+    0  : Charger Red
+    1  : Charger Green
+
+MC13783 regulators:
+    sw1a      : regulator SW1A      (register 24, bit 0)
+    sw1b      : regulator SW1B      (register 25, bit 0)
+    sw2a      : regulator SW2A      (register 26, bit 0)
+    sw2b      : regulator SW2B      (register 27, bit 0)
+    sw3       : regulator SW3       (register 29, bit 20)
+    vaudio    : regulator VAUDIO    (register 32, bit 0)
+    viohi     : regulator VIOHI     (register 32, bit 3)
+    violo     : regulator VIOLO     (register 32, bit 6)
+    vdig      : regulator VDIG      (register 32, bit 9)
+    vgen      : regulator VGEN      (register 32, bit 12)
+    vrfdig    : regulator VRFDIG    (register 32, bit 15)
+    vrfref    : regulator VRFREF    (register 32, bit 18)
+    vrfcp     : regulator VRFCP     (register 32, bit 21)
+    vsim      : regulator VSIM      (register 33, bit 0)
+    vesim     : regulator VESIM     (register 33, bit 3)
+    vcam      : regulator VCAM      (register 33, bit 6)
+    vrfbg     : regulator VRFBG     (register 33, bit 9)
+    vvib      : regulator VVIB      (register 33, bit 11)
+    vrf1      : regulator VRF1      (register 33, bit 12)
+    vrf2      : regulator VRF2      (register 33, bit 15)
+    vmmc1     : regulator VMMC1     (register 33, bit 18)
+    vmmc2     : regulator VMMC2     (register 33, bit 21)
+    gpo1      : regulator GPO1      (register 34, bit 6)
+    gpo2      : regulator GPO2      (register 34, bit 8)
+    gpo3      : regulator GPO3      (register 34, bit 10)
+    gpo4      : regulator GPO4      (register 34, bit 12)
+    pwgt1spi  : regulator PWGT1SPI  (register 34, bit 15)
+    pwgt2spi  : regulator PWGT2SPI  (register 34, bit 16)
+
+MC13892 regulators:
+    vcoincell : regulator VCOINCELL (register 13, bit 23)
+    sw1       : regulator SW1	    (register 24, bit 0)
+    sw2       : regulator SW2	    (register 25, bit 0)
+    sw3       : regulator SW3	    (register 26, bit 0)
+    sw4       : regulator SW4	    (register 27, bit 0)
+    swbst     : regulator SWBST	    (register 29, bit 20)
+    vgen1     : regulator VGEN1	    (register 32, bit 0)
+    viohi     : regulator VIOHI	    (register 32, bit 3)
+    vdig      : regulator VDIG	    (register 32, bit 9)
+    vgen2     : regulator VGEN2	    (register 32, bit 12)
+    vpll      : regulator VPLL	    (register 32, bit 15)
+    vusb2     : regulator VUSB2	    (register 32, bit 18)
+    vgen3     : regulator VGEN3	    (register 33, bit 0)
+    vcam      : regulator VCAM	    (register 33, bit 6)
+    vvideo    : regulator VVIDEO    (register 33, bit 12)
+    vaudio    : regulator VAUDIO    (register 33, bit 15)
+    vsd       : regulator VSD	    (register 33, bit 18)
+    gpo1      : regulator GPO1	    (register 34, bit 6)
+    gpo2      : regulator GPO2	    (register 34, bit 8)
+    gpo3      : regulator GPO3	    (register 34, bit 10)
+    gpo4      : regulator GPO4	    (register 34, bit 12)
+    pwgt1spi  : regulator PWGT1SPI  (register 34, bit 15)
+    pwgt2spi  : regulator PWGT2SPI  (register 34, bit 16)
+    vusb      : regulator VUSB	    (register 50, bit 3)
+
+  The bindings details of individual regulator device can be found in:
+  Documentation/devicetree/bindings/regulator/regulator.txt
+
+Examples:
+
+ecspi@70010000 { /* ECSPI1 */
+	cs-gpios = <&gpio4 24 0>, /* GPIO4_24 */
+		   <&gpio4 25 0>; /* GPIO4_25 */
+
+	pmic: mc13892@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mc13892";
+		spi-max-frequency = <6000000>;
+		reg = <0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <8>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			led-control = <0x000 0x000 0x0e0 0x000>;
+
+			sysled@3 {
+				reg = <3>;
+				label = "system:red:live";
+				linux,default-trigger = "heartbeat";
+			};
+		};
+
+		regulators {
+			sw1_reg: mc13892__sw1 {
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <1375000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw2_reg: mc13892__sw2 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/mfd.txt b/Documentation/devicetree/bindings/mfd/mfd.txt
new file mode 100644
index 000000000..336c0495c
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/mfd.txt
@@ -0,0 +1,51 @@
+Multi-Function Devices (MFD)
+
+These devices comprise a nexus for heterogeneous hardware blocks containing
+more than one non-unique yet varying hardware functionality.
+
+A typical MFD can be:
+
+- A mixed signal ASIC on an external bus, sometimes a PMIC (Power Management
+  Integrated Circuit) that is manufactured in a lower technology node (rough
+  silicon) that handles analog drivers for things like audio amplifiers, LED
+  drivers, level shifters, PHY (physical interfaces to things like USB or
+  ethernet), regulators etc.
+
+- A range of memory registers containing "miscellaneous system registers" also
+  known as a system controller "syscon" or any other memory range containing a
+  mix of unrelated hardware devices.
+
+Optional properties:
+
+- compatible : "simple-mfd" - this signifies that the operating system should
+  consider all subnodes of the MFD device as separate devices akin to how
+  "simple-bus" indicates when to see subnodes as children for a simple
+  memory-mapped bus. For more complex devices, when the nexus driver has to
+  probe registers to figure out what child devices exist etc, this should not
+  be used. In the latter case the child devices will be determined by the
+  operating system.
+
+- ranges: Describes the address mapping relationship to the parent. Should set
+  the child's base address to 0, the physical address within parent's address
+  space, and the length of the address map.
+
+- #address-cells: Specifies the number of cells used to represent physical base
+  addresses. Must be present if ranges is used.
+
+- #size-cells: Specifies the number of cells used to represent the size of an
+  address. Must be present if ranges is used.
+
+Example:
+
+foo@1000 {
+	compatible = "syscon", "simple-mfd";
+	reg = <0x01000 0x1000>;
+
+	led@8.0 {
+		compatible = "register-bit-led";
+		offset = <0x08>;
+		mask = <0x01>;
+		label = "myled";
+		default-state = "on";
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/motorola-cpcap.txt b/Documentation/devicetree/bindings/mfd/motorola-cpcap.txt
new file mode 100644
index 000000000..5ddcc8f4f
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/motorola-cpcap.txt
@@ -0,0 +1,72 @@
+Motorola CPCAP PMIC device tree binding
+
+Required properties:
+- compatible		: One or both of "motorola,cpcap" or "ste,6556002"
+- reg			: SPI chip select
+- interrupts		: The interrupt line the device is connected to
+- interrupt-controller	: Marks the device node as an interrupt controller
+- #interrupt-cells	: The number of cells to describe an IRQ, should be 2
+- #address-cells	: Child device offset number of cells, should be 1
+- #size-cells		: Child device size number of cells, should be 0
+- spi-max-frequency	: Typically set to 3000000
+- spi-cs-high		: SPI chip select direction
+
+Optional subnodes:
+
+The sub-functions of CPCAP get their own node with their own compatible values,
+which are described in the following files:
+
+- ../power/supply/cpcap-battery.txt
+- ../power/supply/cpcap-charger.txt
+- ../regulator/cpcap-regulator.txt
+- ../phy/phy-cpcap-usb.txt
+- ../input/cpcap-pwrbutton.txt
+- ../rtc/cpcap-rtc.txt
+- ../leds/leds-cpcap.txt
+- ../iio/adc/cpcap-adc.txt
+
+The only exception is the audio codec. Instead of a compatible value its
+node must be named "audio-codec".
+
+Required properties for the audio-codec subnode:
+
+- #sound-dai-cells = <1>;
+
+The audio-codec provides two DAIs. The first one is connected to the
+Stereo HiFi DAC and the second one is connected to the Voice DAC.
+
+Example:
+
+&mcspi1 {
+	cpcap: pmic@0 {
+		compatible = "motorola,cpcap", "ste,6556002";
+		reg = <0>;	/* cs0 */
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_EDGE_RISING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <3000000>;
+		spi-cs-high;
+
+		audio-codec {
+			#sound-dai-cells = <1>;
+
+			/* HiFi */
+			port@0 {
+				endpoint {
+					remote-endpoint = <&cpu_dai1>;
+				};
+			};
+
+			/* Voice */
+			port@1 {
+				endpoint {
+					remote-endpoint = <&cpu_dai2>;
+				};
+			};
+		};
+	};
+};
+
diff --git a/Documentation/devicetree/bindings/mfd/mps,mp2629.yaml b/Documentation/devicetree/bindings/mfd/mps,mp2629.yaml
new file mode 100644
index 000000000..f91acc42d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/mps,mp2629.yaml
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/mps,mp2629.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MP2629 Battery Charger PMIC from Monolithic Power System.
+
+maintainers:
+  - Saravanan Sekar <sravanhome@gmail.com>
+
+description: |
+  MP2629 is a PMIC providing battery charging and power supply for smartphones,
+  wireless camera and portable devices. Chip is controlled over I2C.
+
+  The battery charge management device handles battery charger controller and
+  ADC IIO device for battery, system voltage
+
+properties:
+  compatible:
+    const: mps,mp2629
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  interrupt-controller: true
+
+  "#interrupt-cells":
+    const: 2
+    description:
+      The first cell is the IRQ number, the second cell is the trigger type.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-controller
+  - "#interrupt-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/input/linux-event-codes.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pmic@4b {
+            compatible = "mps,mp2629";
+            reg = <0x4b>;
+
+            interrupt-controller;
+            interrupt-parent = <&gpio2>;
+            #interrupt-cells = <2>;
+            interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mfd/mt6397.txt b/Documentation/devicetree/bindings/mfd/mt6397.txt
new file mode 100644
index 000000000..2661775a3
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/mt6397.txt
@@ -0,0 +1,102 @@
+MediaTek MT6397/MT6323 Multifunction Device Driver
+
+MT6397/MT6323 is a multifunction device with the following sub modules:
+- Regulator
+- RTC
+- Audio codec
+- GPIO
+- Clock
+- LED
+- Keys
+- Power controller
+
+It is interfaced to host controller using SPI interface by a proprietary hardware
+called PMIC wrapper or pwrap. MT6397/MT6323 MFD is a child device of pwrap.
+See the following for pwarp node definitions:
+../soc/mediatek/pwrap.txt
+
+This document describes the binding for MFD device and its sub module.
+
+Required properties:
+compatible:
+	"mediatek,mt6323" for PMIC MT6323
+	"mediatek,mt6358" for PMIC MT6358
+	"mediatek,mt6397" for PMIC MT6397
+
+Optional subnodes:
+
+- rtc
+	Required properties: Should be one of follows
+		- compatible: "mediatek,mt6323-rtc"
+		- compatible: "mediatek,mt6358-rtc"
+		- compatible: "mediatek,mt6397-rtc"
+	For details, see ../rtc/rtc-mt6397.txt
+- regulators
+	Required properties:
+		- compatible: "mediatek,mt6323-regulator"
+	see ../regulator/mt6323-regulator.txt
+		- compatible: "mediatek,mt6358-regulator"
+	see ../regulator/mt6358-regulator.txt
+		- compatible: "mediatek,mt6397-regulator"
+	see ../regulator/mt6397-regulator.txt
+- codec
+	Required properties:
+		- compatible: "mediatek,mt6397-codec" or "mediatek,mt6358-sound"
+- clk
+	Required properties:
+		- compatible: "mediatek,mt6397-clk"
+- led
+	Required properties:
+		- compatible: "mediatek,mt6323-led"
+	see ../leds/leds-mt6323.txt
+
+- keys
+	Required properties:
+		- compatible: "mediatek,mt6397-keys" or "mediatek,mt6323-keys"
+	see ../input/mtk-pmic-keys.txt
+
+- power-controller
+	Required properties:
+		- compatible: "mediatek,mt6323-pwrc"
+	For details, see ../power/reset/mt6323-poweroff.txt
+
+- pin-controller
+	Required properties:
+		- compatible: "mediatek,mt6397-pinctrl"
+	For details, see ../pinctrl/pinctrl-mt65xx.txt
+
+Example:
+	pwrap: pwrap@1000f000 {
+		compatible = "mediatek,mt8135-pwrap";
+
+		...
+
+		pmic {
+			compatible = "mediatek,mt6397";
+
+			codec: mt6397codec {
+				compatible = "mediatek,mt6397-codec";
+			};
+
+			regulators {
+				compatible = "mediatek,mt6397-regulator";
+
+				mt6397_vpca15_reg: buck_vpca15 {
+					regulator-compatible = "buck_vpca15";
+					regulator-name = "vpca15";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1400000>;
+					regulator-ramp-delay = <12500>;
+					regulator-always-on;
+				};
+
+				mt6397_vgp4_reg: ldo_vgp4 {
+					regulator-compatible = "ldo_vgp4";
+					regulator-name = "vgp4";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-enable-ramp-delay = <218>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/mxs-lradc.txt b/Documentation/devicetree/bindings/mfd/mxs-lradc.txt
new file mode 100644
index 000000000..755cbef06
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/mxs-lradc.txt
@@ -0,0 +1,45 @@
+* Freescale MXS LRADC device driver
+
+Required properties:
+- compatible: Should be "fsl,imx23-lradc" for i.MX23 SoC and "fsl,imx28-lradc"
+              for i.MX28 SoC
+- reg: Address and length of the register set for the device
+- interrupts: Should contain the LRADC interrupts
+
+Optional properties:
+- fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen
+                               to LRADC. Valid value is either 4 or 5. If this
+                               property is not present, then the touchscreen is
+                               disabled. 5 wires is valid for i.MX28 SoC only.
+- fsl,ave-ctrl: number of samples per direction to calculate an average value.
+                Allowed value is 1 ... 32, default is 4
+- fsl,ave-delay: delay between consecutive samples. Allowed value is
+                 2 ... 2048. It is used if 'fsl,ave-ctrl' > 1, counts at
+                 2 kHz and its default is 2 (= 1 ms)
+- fsl,settling: delay between plate switch to next sample. Allowed value is
+                1 ... 2047. It counts at 2 kHz and its default is
+                10 (= 5 ms)
+
+Example for i.MX23 SoC:
+
+	lradc@80050000 {
+		compatible = "fsl,imx23-lradc";
+		reg = <0x80050000 0x2000>;
+		interrupts = <36 37 38 39 40 41 42 43 44>;
+		fsl,lradc-touchscreen-wires = <4>;
+		fsl,ave-ctrl = <4>;
+		fsl,ave-delay = <2>;
+		fsl,settling = <10>;
+	};
+
+Example for i.MX28 SoC:
+
+	lradc@80050000 {
+		compatible = "fsl,imx28-lradc";
+		reg = <0x80050000 0x2000>;
+		interrupts = <10 14 15 16 17 18 19 20 21 22 23 24 25>;
+		fsl,lradc-touchscreen-wires = <5>;
+		fsl,ave-ctrl = <4>;
+		fsl,ave-delay = <2>;
+		fsl,settling = <10>;
+	};
diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt
new file mode 100644
index 000000000..aa1eaa595
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt
@@ -0,0 +1,103 @@
+OMAP HS USB Host
+
+Required properties:
+
+- compatible: should be "ti,usbhs-host"
+- reg: should contain one register range i.e. start and length
+- ti,hwmods: must contain "usb_host_hs"
+
+Optional properties:
+
+- num-ports: number of USB ports. Usually this is automatically detected
+  from the IP's revision register but can be overridden by specifying
+  this property. A maximum of 3 ports are supported at the moment.
+
+- portN-mode: String specifying the port mode for port N, where N can be
+  from 1 to 3. If the port mode is not specified, that port is treated
+  as unused. When specified, it must be one of the following.
+	"ehci-phy",
+        "ehci-tll",
+        "ehci-hsic",
+        "ohci-phy-6pin-datse0",
+        "ohci-phy-6pin-dpdm",
+        "ohci-phy-3pin-datse0",
+        "ohci-phy-4pin-dpdm",
+        "ohci-tll-6pin-datse0",
+        "ohci-tll-6pin-dpdm",
+        "ohci-tll-3pin-datse0",
+        "ohci-tll-4pin-dpdm",
+        "ohci-tll-2pin-datse0",
+        "ohci-tll-2pin-dpdm",
+
+- single-ulpi-bypass: Must be present if the controller contains a single
+  ULPI bypass control bit. e.g. OMAP3 silicon <= ES2.1
+
+- clocks: a list of phandles and clock-specifier pairs, one for each entry in
+  clock-names.
+
+- clock-names: should include:
+  For OMAP3
+  * "usbhost_120m_fck" - 120MHz Functional clock.
+
+  For OMAP4+
+  * "refclk_60m_int" - 60MHz internal reference clock for UTMI clock mux
+  * "refclk_60m_ext_p1" - 60MHz external ref. clock for Port 1's UTMI clock mux.
+  * "refclk_60m_ext_p2" - 60MHz external ref. clock for Port 2's UTMI clock mux
+  * "utmi_p1_gfclk" - Port 1 UTMI clock mux.
+  * "utmi_p2_gfclk" - Port 2 UTMI clock mux.
+  * "usb_host_hs_utmi_p1_clk" - Port 1 UTMI clock gate.
+  * "usb_host_hs_utmi_p2_clk" - Port 2 UTMI clock gate.
+  * "usb_host_hs_utmi_p3_clk" - Port 3 UTMI clock gate.
+  * "usb_host_hs_hsic480m_p1_clk" - Port 1 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic480m_p2_clk" - Port 2 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic480m_p3_clk" - Port 3 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p1_clk" - Port 1 60MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p2_clk" - Port 2 60MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p3_clk" - Port 3 60MHz HSIC clock gate.
+
+Required properties if child node exists:
+
+- #address-cells: Must be 1
+- #size-cells: Must be 1
+- ranges: must be present
+
+Properties for children:
+
+The OMAP HS USB Host subsystem contains EHCI and OHCI controllers.
+See Documentation/devicetree/bindings/usb/ehci-omap.txt and
+Documentation/devicetree/bindings/usb/ohci-omap3.txt.
+
+Example for OMAP4:
+
+usbhshost: usbhshost@4a064000 {
+	compatible = "ti,usbhs-host";
+	reg = <0x4a064000 0x800>;
+	ti,hwmods = "usb_host_hs";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	usbhsohci: ohci@4a064800 {
+		compatible = "ti,ohci-omap3", "usb-ohci";
+		reg = <0x4a064800 0x400>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 76 0x4>;
+	};
+
+	usbhsehci: ehci@4a064c00 {
+		compatible = "ti,ehci-omap", "usb-ehci";
+		reg = <0x4a064c00 0x400>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 77 0x4>;
+	};
+};
+
+&usbhshost {
+	port1-mode = "ehci-phy";
+	port2-mode = "ehci-tll";
+	port3-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <&hsusb1_phy 0 &hsusb3_phy>;
+};
diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt
new file mode 100644
index 000000000..c58d70437
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt
@@ -0,0 +1,27 @@
+OMAP HS USB Host TLL (Transceiver-Less Interface)
+
+Required properties:
+
+- compatible : should be "ti,usbhs-tll"
+- reg : should contain one register range i.e. start and length
+- interrupts : should contain the TLL module's interrupt
+- ti,hwmod : must contain "usb_tll_hs"
+
+Optional properties:
+
+- clocks: a list of phandles and clock-specifier pairs, one for each entry in
+  clock-names.
+
+- clock-names: should include:
+  * "usb_tll_hs_usb_ch0_clk" - USB TLL channel 0 clock
+  * "usb_tll_hs_usb_ch1_clk" - USB TLL channel 1 clock
+  * "usb_tll_hs_usb_ch2_clk" - USB TLL channel 2 clock
+
+Example:
+
+	usbhstll: usbhstll@4a062000 {
+		compatible = "ti,usbhs-tll";
+		reg = <0x4a062000 0x1000>;
+		interrupts = <78>;
+		ti,hwmods = "usb_tll_hs";
+	  };
diff --git a/Documentation/devicetree/bindings/mfd/palmas.txt b/Documentation/devicetree/bindings/mfd/palmas.txt
new file mode 100644
index 000000000..e736ab301
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/palmas.txt
@@ -0,0 +1,52 @@
+* palmas device tree bindings
+
+The TI palmas family current members :-
+twl6035 (palmas)
+twl6037 (palmas)
+tps65913 (palmas)
+tps65914 (palmas)
+tps659038
+tps65917
+
+Required properties:
+- compatible : Should be from the list
+  ti,twl6035
+  ti,twl6036
+  ti,twl6037
+  ti,tps65913
+  ti,tps65914
+  ti,tps80036
+  ti,tps659038
+  ti,tps65917
+and also the generic series names
+  ti,palmas
+- interrupt-controller : palmas has its own internal IRQs
+- #interrupt-cells : should be set to 2 for IRQ number and flags
+  The first cell is the IRQ number.
+  The second cell is the flags, encoded as the trigger masks from
+  Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+Optional properties:
+  ti,mux-padX : set the pad register X (1-2) to the correct muxing for the
+		hardware, if not set will use muxing in OTP.
+
+Example:
+
+palmas {
+	compatible = "ti,twl6035", "ti,palmas";
+	reg = <0x48>
+	interrupt-parent = <&intc>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+
+	ti,mux-pad1 = <0>;
+	ti,mux-pad2 = <0>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pmic {
+		compatible = "ti,twl6035-pmic", "ti,palmas-pmic";
+		....
+	};
+}
diff --git a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt
new file mode 100644
index 000000000..79367a43b
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt
@@ -0,0 +1,80 @@
+          Qualcomm SPMI PMICs multi-function device bindings
+
+The Qualcomm SPMI series presently includes PM8941, PM8841 and PMA8084
+PMICs.  These PMICs use a QPNP scheme through SPMI interface.
+QPNP is effectively a partitioning scheme for dividing the SPMI extended
+register space up into logical pieces, and set of fixed register
+locations/definitions within these regions, with some of these regions
+specifically used for interrupt handling.
+
+The QPNP PMICs are used with the Qualcomm Snapdragon series SoCs, and are
+interfaced to the chip via the SPMI (System Power Management Interface) bus.
+Support for multiple independent functions are implemented by splitting the
+16-bit SPMI slave address space into 256 smaller fixed-size regions, 256 bytes
+each. A function can consume one or more of these fixed-size register regions.
+
+Required properties:
+- compatible:      Should contain one of:
+                   "qcom,pm8941",
+                   "qcom,pm8841",
+                   "qcom,pma8084",
+                   "qcom,pm8019",
+                   "qcom,pm8226",
+                   "qcom,pm8110",
+                   "qcom,pma8084",
+                   "qcom,pmi8962",
+                   "qcom,pmd9635",
+                   "qcom,pm8994",
+                   "qcom,pmi8994",
+                   "qcom,pm8916",
+                   "qcom,pm8004",
+                   "qcom,pm8909",
+                   "qcom,pm8950",
+                   "qcom,pmi8950",
+                   "qcom,pm8998",
+                   "qcom,pmi8998",
+                   "qcom,pm8005",
+                   or generalized "qcom,spmi-pmic".
+- reg:             Specifies the SPMI USID slave address for this device.
+                   For more information see:
+                   Documentation/devicetree/bindings/spmi/spmi.yaml
+
+Required properties for peripheral child nodes:
+- compatible:      Should contain "qcom,xxx", where "xxx" is a peripheral name.
+
+Optional properties for peripheral child nodes:
+- interrupts:      Interrupts are specified as a 4-tuple. For more information
+                   see:
+                   Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
+- interrupt-names: Corresponding interrupt name to the interrupts property
+
+Each child node of SPMI slave id represents a function of the PMIC. In the
+example below the rtc device node represents a peripheral of pm8941
+SID = 0. The regulator device node represents a peripheral of pm8941 SID = 1.
+
+Example:
+
+	spmi {
+		compatible = "qcom,spmi-pmic-arb";
+
+		pm8941@0 {
+			compatible = "qcom,pm8941", "qcom,spmi-pmic";
+			reg = <0x0 SPMI_USID>;
+
+			rtc {
+				compatible = "qcom,rtc";
+				interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+				interrupt-names = "alarm";
+			};
+		};
+
+		pm8941@1 {
+			compatible = "qcom,pm8941", "qcom,spmi-pmic";
+			reg = <0x1 SPMI_USID>;
+
+			regulator {
+				compatible = "qcom,regulator";
+				regulator-name = "8941_boost";
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/qcom,tcsr.txt b/Documentation/devicetree/bindings/mfd/qcom,tcsr.txt
new file mode 100644
index 000000000..e90519d56
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/qcom,tcsr.txt
@@ -0,0 +1,22 @@
+QCOM Top Control and Status Register
+
+Qualcomm devices have a set of registers that provide various control and status
+functions for their peripherals.  This node is intended to allow access to these
+registers via syscon.
+
+Required properties:
+- compatible:	Should contain:
+		"qcom,tcsr-ipq8064", "syscon" for IPQ8064
+		"qcom,tcsr-apq8064", "syscon" for APQ8064
+		"qcom,tcsr-msm8660", "syscon" for MSM8660
+		"qcom,tcsr-msm8960", "syscon" for MSM8960
+		"qcom,tcsr-msm8974", "syscon" for MSM8974
+		"qcom,tcsr-apq8084", "syscon" for APQ8084
+		"qcom,tcsr-msm8916", "syscon" for MSM8916
+- reg: Address range for TCSR registers
+
+Example:
+	tcsr: syscon@1a400000 {
+		compatible = "qcom,tcsr-msm8960", "syscon";
+		reg = <0x1a400000 0x100>;
+	};
diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt
new file mode 100644
index 000000000..9e5eba4a4
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt
@@ -0,0 +1,99 @@
+Qualcomm PM8xxx PMIC multi-function devices
+
+The PM8xxx family of Power Management ICs are used to provide regulated
+voltages and other various functionality to Qualcomm SoCs.
+
+= PROPERTIES
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,pm8058"
+		    "qcom,pm8821"
+		    "qcom,pm8921"
+
+- #address-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 1
+
+- #size-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 0
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: specifies the interrupt that indicates a subdevice
+		    has generated an interrupt (summary interrupt). The
+		    format of the specifier is defined by the binding document
+		    describing the node's interrupt parent.
+
+- #interrupt-cells:
+	Usage: required
+	Value type : <u32>
+	Definition: must be 2. Specifies the number of cells needed to encode
+		    an interrupt source. The 1st cell contains the interrupt
+		    number. The 2nd cell is the trigger type and level flags
+		    encoded as follows:
+
+			1 = low-to-high edge triggered
+			2 = high-to-low edge triggered
+			4 = active high level-sensitive
+			8 = active low level-sensitive
+
+- interrupt-controller:
+	Usage: required
+	Value type: <empty>
+	Definition: identifies this node as an interrupt controller
+
+= SUBCOMPONENTS
+
+The PMIC contains multiple independent functions, each described in a subnode.
+The below bindings specify the set of valid subnodes.
+
+== Real-Time Clock
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,pm8058-rtc"
+		    "qcom,pm8921-rtc"
+		    "qcom,pm8941-rtc"
+		    "qcom,pm8018-rtc"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: single entry specifying the base address of the RTC registers
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: single entry specifying the RTC's alarm interrupt
+
+- allow-set-time:
+	Usage: optional
+	Value type: <empty>
+	Definition: indicates that the setting of RTC time is allowed by
+		    the host CPU
+
+= EXAMPLE
+
+	pmicintc: pmic@0 {
+		compatible = "qcom,pm8921";
+		interrupts = <104 8>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtc@11d {
+			compatible = "qcom,pm8921-rtc";
+			reg = <0x11d>;
+			interrupts = <0x27 0>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
new file mode 100644
index 000000000..b823b8625
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
@@ -0,0 +1,283 @@
+Qualcomm Resource Power Manager (RPM)
+
+This driver is used to interface with the Resource Power Manager (RPM) found in
+various Qualcomm platforms. The RPM allows each component in the system to vote
+for state of the system resources, such as clocks, regulators and bus
+frequencies.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,rpm-apq8064"
+		    "qcom,rpm-msm8660"
+		    "qcom,rpm-msm8960"
+		    "qcom,rpm-ipq8064"
+		    "qcom,rpm-mdm9615"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: base address and size of the RPM's message ram
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: three entries specifying the RPM's:
+		    1. acknowledgement interrupt
+		    2. error interrupt
+		    3. wakeup interrupt
+
+- interrupt-names:
+	Usage: required
+	Value type: <string-array>
+	Definition: must be the three strings "ack", "err" and "wakeup", in order
+
+- qcom,ipc:
+	Usage: required
+	Value type: <prop-encoded-array>
+
+	Definition: three entries specifying the outgoing ipc bit used for
+		    signaling the RPM:
+		    - phandle to a syscon node representing the apcs registers
+		    - u32 representing offset to the register within the syscon
+		    - u32 representing the ipc bit within the register
+
+
+= SUBNODES
+
+The RPM exposes resources to its subnodes. The below bindings specify the set
+of valid subnodes that can operate on these resources.
+
+== Regulators
+
+Regulator nodes are identified by their compatible:
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,rpm-pm8058-regulators"
+		    "qcom,rpm-pm8901-regulators"
+		    "qcom,rpm-pm8921-regulators"
+		    "qcom,rpm-pm8018-regulators"
+		    "qcom,rpm-smb208-regulators"
+
+- vdd_l0_l1_lvs-supply:
+- vdd_l2_l11_l12-supply:
+- vdd_l3_l4_l5-supply:
+- vdd_l6_l7-supply:
+- vdd_l8-supply:
+- vdd_l9-supply:
+- vdd_l10-supply:
+- vdd_l13_l16-supply:
+- vdd_l14_l15-supply:
+- vdd_l17_l18-supply:
+- vdd_l19_l20-supply:
+- vdd_l21-supply:
+- vdd_l22-supply:
+- vdd_l23_l24_l25-supply:
+- vdd_ncp-supply:
+- vdd_s0-supply:
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+	Usage: optional (pm8058 only)
+	Value type: <phandle>
+	Definition: reference to regulator supplying the input pin, as
+		    described in the data sheet
+
+- lvs0_in-supply:
+- lvs1_in-supply:
+- lvs2_in-supply:
+- lvs3_in-supply:
+- mvs_in-supply:
+- vdd_l0-supply:
+- vdd_l1-supply:
+- vdd_l2-supply:
+- vdd_l3-supply:
+- vdd_l4-supply:
+- vdd_l5-supply:
+- vdd_l6-supply:
+- vdd_s0-supply:
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+	Usage: optional (pm8901 only)
+	Value type: <phandle>
+	Definition: reference to regulator supplying the input pin, as
+		    described in the data sheet
+
+- vdd_l1_l2_l12_l18-supply:
+- vdd_l3_l15_l17-supply:
+- vdd_l4_l14-supply:
+- vdd_l5_l8_l16-supply:
+- vdd_l6_l7-supply:
+- vdd_l9_l11-supply:
+- vdd_l10_l22-supply:
+- vdd_l21_l23_l29-supply:
+- vdd_l24-supply:
+- vdd_l25-supply:
+- vdd_l26-supply:
+- vdd_l27-supply:
+- vdd_l28-supply:
+- vdd_ncp-supply:
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s4-supply:
+- vdd_s5-supply:
+- vdd_s6-supply:
+- vdd_s7-supply:
+- vdd_s8-supply:
+- vin_5vs-supply:
+- vin_lvs1_3_6-supply:
+- vin_lvs2-supply:
+- vin_lvs4_5_7-supply:
+	Usage: optional (pm8921 only)
+	Value type: <phandle>
+	Definition: reference to regulator supplying the input pin, as
+		    described in the data sheet
+
+- vin_lvs1-supply:
+- vdd_l7-supply:
+- vdd_l8-supply:
+- vdd_l9_l10_l11_l12-supply:
+	Usage: optional (pm8018 only)
+	Value type: <phandle>
+	Definition: reference to regulator supplying the input pin, as
+		    described in the data sheet
+
+The regulator node houses sub-nodes for each regulator within the device. Each
+sub-node is identified using the node's name, with valid values listed for each
+of the pmics below.
+
+pm8058:
+	l0, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15,
+	l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, s0, s1, s2, s3, s4,
+	lvs0, lvs1, ncp
+
+pm8901:
+	l0, l1, l2, l3, l4, l5, l6, s0, s1, s2, s3, s4, lvs0, lvs1, lvs2, lvs3,
+	mvs
+
+pm8921:
+	s1, s2, s3, s4, s7, s8, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
+	l12, l14, l15, l16, l17, l18, l21, l22, l23, l24, l25, l26, l27, l28,
+	l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch,
+	ncp
+
+pm8018:
+	s1, s2, s3, s4, s5, , l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
+	l12, l14, lvs1
+
+smb208:
+	s1a, s1b, s2a, s2b
+
+The content of each sub-node is defined by the standard binding for regulators -
+see regulator.txt - with additional custom properties described below:
+
+=== Switch-mode Power Supply regulator custom properties
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <empty>
+	Definition: enable pull down of the regulator when inactive
+
+- qcom,switch-mode-frequency:
+	Usage: required
+	Value type: <u32>
+	Definition: Frequency (Hz) of the switch-mode power supply;
+		    must be one of:
+		    19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
+		    2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
+		    1480000, 1370000, 1280000, 1200000
+
+- qcom,force-mode:
+	Usage: optional (default if no other qcom,force-mode is specified)
+	Value type: <u32>
+	Definition: indicates that the regulator should be forced to a
+		   particular mode, valid values are:
+		   QCOM_RPM_FORCE_MODE_NONE - do not force any mode
+		   QCOM_RPM_FORCE_MODE_LPM - force into low power mode
+		   QCOM_RPM_FORCE_MODE_HPM - force into high power mode
+		   QCOM_RPM_FORCE_MODE_AUTO - allow regulator to automatically
+					      select its own mode based on
+					      realtime current draw, only for:
+					      pm8921 smps and ftsmps
+
+- qcom,power-mode-hysteretic:
+	Usage: optional
+	Value type: <empty>
+	Definition: select that the power supply should operate in hysteretic
+		    mode, instead of the default pwm mode
+
+=== Low-dropout regulator custom properties
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <empty>
+	Definition: enable pull down of the regulator when inactive
+
+- qcom,force-mode:
+	Usage: optional
+	Value type: <u32>
+	Definition: indicates that the regulator should not be forced to any
+		   particular mode, valid values are:
+		   QCOM_RPM_FORCE_MODE_NONE - do not force any mode
+		   QCOM_RPM_FORCE_MODE_LPM - force into low power mode
+		   QCOM_RPM_FORCE_MODE_HPM - force into high power mode
+		   QCOM_RPM_FORCE_MODE_BYPASS - set regulator to use bypass
+						mode, i.e.  to act as a switch
+						and not regulate, only for:
+						pm8921 pldo, nldo and nldo1200
+
+=== Negative Charge Pump custom properties
+
+- qcom,switch-mode-frequency:
+	Usage: required
+	Value type: <u32>
+	Definition: Frequency (Hz) of the switch mode power supply;
+		    must be one of:
+		    19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
+		    2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
+		    1480000, 1370000, 1280000, 1200000
+
+= EXAMPLE
+
+	#include <dt-bindings/mfd/qcom-rpm.h>
+
+	rpm@108000 {
+		compatible = "qcom,rpm-msm8960";
+		reg = <0x108000 0x1000>;
+		qcom,ipc = <&apcs 0x8 2>;
+
+		interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
+		interrupt-names = "ack", "err", "wakeup";
+
+		regulators {
+			compatible = "qcom,rpm-pm8921-regulators";
+			vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+
+			s1 {
+				regulator-min-microvolt = <1225000>;
+				regulator-max-microvolt = <1225000>;
+
+				bias-pull-down;
+
+				qcom,switch-mode-frequency = <3200000>;
+			};
+
+			pm8921_s4: s4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				qcom,switch-mode-frequency = <1600000>;
+				bias-pull-down;
+
+				qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+			};
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/mfd/qriox.txt b/Documentation/devicetree/bindings/mfd/qriox.txt
new file mode 100644
index 000000000..f301e2d4c
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/qriox.txt
@@ -0,0 +1,17 @@
+KEYMILE qrio Board Control CPLD
+
+The qrio is a multifunction device that controls the KEYMILE boards based on
+the kmp204x design.
+It is consists of a reset controller, watchdog timer, LEDs, and 2 IRQ capable
+GPIO blocks.
+
+Required properties:
+- compatible: "keymile,qriox"
+- reg: access on the parent local bus (chip select, offset in chip select, size)
+
+Example:
+
+	board-control@1,0 {
+		compatible = "keymile,qriox";
+		reg = <1 0 0x80>;
+	};
diff --git a/Documentation/devicetree/bindings/mfd/retu.txt b/Documentation/devicetree/bindings/mfd/retu.txt
new file mode 100644
index 000000000..df3005dd3
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/retu.txt
@@ -0,0 +1,24 @@
+* Device tree bindings for Nokia Retu and Tahvo multi-function device
+
+Retu and Tahvo are a multi-function devices found on Nokia Internet
+Tablets (770, N800 and N810). The Retu chip provides watchdog timer
+and power button control functionalities while Tahvo chip provides
+USB transceiver functionality.
+
+Required properties:
+- compatible:		"nokia,retu" or "nokia,tahvo"
+- reg:			Specifies the CBUS slave address of the ASIC chip
+- interrupts: 		The interrupt line the device is connected to
+
+Example:
+
+cbus0 {
+	compatible = "i2c-cbus-gpio";
+	...
+	retu: retu@1 {
+		compatible = "nokia,retu";
+		interrupt-parent = <&gpio4>;
+		interrupts = <12 IRQ_TYPE_EDGE_RISING>;
+		reg = <0x1>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt
new file mode 100644
index 000000000..04df07f6f
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rk808.txt
@@ -0,0 +1,277 @@
+RK8XX Power Management Integrated Circuit
+
+The rk8xx family current members:
+rk805
+rk808
+rk809
+rk817
+rk818
+
+Required properties:
+- compatible: "rockchip,rk805"
+- compatible: "rockchip,rk808"
+- compatible: "rockchip,rk809"
+- compatible: "rockchip,rk817"
+- compatible: "rockchip,rk818"
+- reg: I2C slave address
+- interrupts: the interrupt outputs of the controller.
+- #clock-cells: from common clock binding; shall be set to 1 (multiple clock
+  outputs). See <dt-bindings/clock/rockchip,rk808.h> for clock IDs.
+
+Optional properties:
+- clock-output-names: From common clock binding to override the
+  default output clock name
+- rockchip,system-power-controller: Telling whether or not this pmic is controlling
+  the system power.
+
+Optional RK805 properties:
+- vcc1-supply:  The input supply for DCDC_REG1
+- vcc2-supply:  The input supply for DCDC_REG2
+- vcc3-supply:  The input supply for DCDC_REG3
+- vcc4-supply:  The input supply for DCDC_REG4
+- vcc5-supply:  The input supply for LDO_REG1 and LDO_REG2
+- vcc6-supply:  The input supply for LDO_REG3
+
+Optional RK808 properties:
+- vcc1-supply:  The input supply for DCDC_REG1
+- vcc2-supply:  The input supply for DCDC_REG2
+- vcc3-supply:  The input supply for DCDC_REG3
+- vcc4-supply:  The input supply for DCDC_REG4
+- vcc6-supply:  The input supply for LDO_REG1 and LDO_REG2
+- vcc7-supply:  The input supply for LDO_REG3 and LDO_REG7
+- vcc8-supply:  The input supply for SWITCH_REG1
+- vcc9-supply:  The input supply for LDO_REG4 and LDO_REG5
+- vcc10-supply: The input supply for LDO_REG6
+- vcc11-supply: The input supply for LDO_REG8
+- vcc12-supply: The input supply for SWITCH_REG2
+- dvs-gpios:  buck1/2 can be controlled by gpio dvs, this is GPIO specifiers
+  for 2 host gpio's used for dvs. The format of the gpio specifier depends in
+  the gpio controller. If DVS GPIOs aren't present, voltage changes will happen
+  very quickly with no slow ramp time.
+
+Optional shared RK809 and RK817 properties:
+- vcc1-supply:  The input supply for DCDC_REG1
+- vcc2-supply:  The input supply for DCDC_REG2
+- vcc3-supply:  The input supply for DCDC_REG3
+- vcc4-supply:  The input supply for DCDC_REG4
+- vcc5-supply:  The input supply for LDO_REG1, LDO_REG2, LDO_REG3
+- vcc6-supply:  The input supply for LDO_REG4, LDO_REG5, LDO_REG6
+- vcc7-supply:  The input supply for LDO_REG7, LDO_REG8, LDO_REG9
+
+Optional RK809 properties:
+- vcc8-supply:  The input supply for SWITCH_REG1
+- vcc9-supply:  The input supply for DCDC_REG5, SWITCH_REG2
+
+Optional RK817 properties:
+- vcc8-supply:  The input supply for BOOST
+- vcc9-supply:  The input supply for OTG_SWITCH
+
+Optional RK818 properties:
+- vcc1-supply:  The input supply for DCDC_REG1
+- vcc2-supply:  The input supply for DCDC_REG2
+- vcc3-supply:  The input supply for DCDC_REG3
+- vcc4-supply:  The input supply for DCDC_REG4
+- boost-supply: The input supply for DCDC_BOOST
+- vcc6-supply:  The input supply for LDO_REG1 and LDO_REG2
+- vcc7-supply:  The input supply for LDO_REG3, LDO_REG5 and LDO_REG7
+- vcc8-supply:  The input supply for LDO_REG4, LDO_REG6 and LDO_REG8
+- vcc9-supply:  The input supply for LDO_REG9 and SWITCH_REG
+- h_5v-supply:  The input supply for HDMI_SWITCH
+- usb-supply:   The input supply for OTG_SWITCH
+
+Regulators: All the regulators of RK8XX to be instantiated shall be
+listed in a child node named 'regulators'. Each regulator is represented
+by a child node of the 'regulators' node.
+
+	regulator-name {
+		/* standard regulator bindings here */
+	};
+
+Following regulators of the RK805 PMIC regulators are supported. Note that
+the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO
+number as described in RK805 datasheet.
+
+	- DCDC_REGn
+		- valid values for n are 1 to 4.
+	- LDO_REGn
+		- valid values for n are 1 to 3
+
+Following regulators of the RK808 PMIC block are supported. Note that
+the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO
+number as described in RK808 datasheet.
+
+	- DCDC_REGn
+		- valid values for n are 1 to 4.
+	- LDO_REGn
+		- valid values for n are 1 to 8.
+	- SWITCH_REGn
+		- valid values for n are 1 to 2
+
+Following regulators of the RK809 and RK817 PMIC blocks are supported. Note that
+the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO
+number as described in RK809 and RK817 datasheets.
+
+	- DCDC_REGn
+		- valid values for n are 1 to 5 for RK809.
+		- valid values for n are 1 to 4 for RK817.
+	- LDO_REGn
+		- valid values for n are 1 to 9 for RK809.
+		- valid values for n are 1 to 9 for RK817.
+	- SWITCH_REGn
+		- valid values for n are 1 to 2 for RK809.
+	- BOOST for RK817
+	- OTG_SWITCH for RK817
+
+Following regulators of the RK818 PMIC block are supported. Note that
+the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO
+number as described in RK818 datasheet.
+
+	- DCDC_REGn
+		- valid values for n are 1 to 4.
+	- LDO_REGn
+		- valid values for n are 1 to 9.
+	- SWITCH_REG
+	- HDMI_SWITCH
+	- OTG_SWITCH
+
+It is necessary to configure three pins for both the RK809 and RK817, the three
+pins are "gpio_ts" "gpio_gt" "gpio_slp".
+	The gpio_gt and gpio_ts pins support the gpio function.
+	The gpio_slp pin is for controlling the pmic states, as below:
+		- reset
+		- power down
+		- sleep
+
+Standard regulator bindings are used inside regulator subnodes. Check
+  Documentation/devicetree/bindings/regulator/regulator.txt
+for more details
+
+Example:
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		clock-output-names = "xin32k", "rk808-clkout2";
+		interrupt-parent = <&gpio0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int &dvs_1 &dvs_2>;
+		dvs-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>,
+			    <&gpio7 15 GPIO_ACTIVE_HIGH>;
+		reg = <0x1b>;
+		rockchip,system-power-controller;
+		wakeup-source;
+		#clock-cells = <1>;
+
+		vcc8-supply = <&vcc_18>;
+		vcc9-supply = <&vcc_io>;
+		vcc10-supply = <&vcc_io>;
+		vcc12-supply = <&vcc_io>;
+		vddio-supply = <&vccio_pmu>;
+
+		regulators {
+			vdd_cpu: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-name = "vdd_arm";
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-name = "vdd_gpu";
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_ddr";
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_io";
+			};
+
+			vccio_pmu: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_pmu";
+			};
+
+			vcc_tp: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_tp";
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd_10";
+			};
+
+			vcc18_lcd: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_lcd";
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+			};
+
+			vdd10_lcd: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd10_lcd";
+			};
+
+			vcc_18: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_18";
+			};
+
+			vcca_codec: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcca_codec";
+			};
+
+			vcc_wl: SWITCH_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_wl";
+			};
+
+			vcc_lcd: SWITCH_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_lcd";
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt
new file mode 100644
index 000000000..16778ea00
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt
@@ -0,0 +1,52 @@
+* Ricoh RN5T567/RN5T618 PMIC
+
+Ricoh RN5T567/RN5T618/RC5T619 is a power management IC family which
+integrates 3 to 5 step-down DCDC converters, 7 to 10 low-dropout regulators,
+GPIOs, and a watchdog timer. It can be controlled through an I2C interface.
+The RN5T618/RC5T619 provides additionally a Li-ion battery charger,
+fuel gauge, and an ADC.
+The RC5T619 additionnally includes USB charger detection and an RTC.
+
+Required properties:
+ - compatible: must be one of
+		"ricoh,rn5t567"
+		"ricoh,rn5t618"
+		"ricoh,rc5t619"
+ - reg: the I2C slave address of the device
+
+Optional properties:
+ - interrupts: interrupt mapping for IRQ
+   See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+ - system-power-controller:
+   See Documentation/devicetree/bindings/power/power-controller.txt
+
+Sub-nodes:
+ - regulators: the node is required if the regulator functionality is
+   needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4
+   (RN5T567/RC5T619), LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, LDO8,
+   LDO9, LDO10, LDORTC1 and LDORTC2.
+   LDO7-10 are specific to RC5T619.
+   The common bindings for each individual regulator can be found in:
+   Documentation/devicetree/bindings/regulator/regulator.txt
+
+Example:
+
+	pmic@32 {
+		compatible = "ricoh,rn5t618";
+		reg = <0x32>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+		system-power-controller;
+
+		regulators {
+			DCDC1 {
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1050000>;
+			};
+
+			DCDC2 {
+				regulator-min-microvolt = <1175000>;
+				regulator-max-microvolt = <1175000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt
new file mode 100644
index 000000000..386eec06c
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt
@@ -0,0 +1,102 @@
+* ROHM BD70528 Power Management Integrated Circuit bindings
+
+BD70528MWV is an ultra-low quiescent current general purpose, single-chip,
+power management IC for battery-powered portable devices. The IC
+integrates 3 ultra-low current consumption buck converters, 3 LDOs and 2
+LED Drivers. Also included are 4 GPIOs, a real-time clock (RTC), a 32kHz
+clock gate, high-accuracy VREF for use with an external ADC, flexible
+dual-input power path, 10 bit SAR ADC for battery temperature monitor and
+1S battery charger with scalable charge currents.
+
+Required properties:
+ - compatible		: Should be "rohm,bd70528"
+ - reg			: I2C slave address.
+ - interrupts		: The interrupt line the device is connected to.
+ - interrupt-controller	: To indicate BD70528 acts as an interrupt controller.
+ - #interrupt-cells	: Should be 2. Usage is compliant to the 2 cells
+			  variant of ../interrupt-controller/interrupts.txt
+ - gpio-controller	: To indicate BD70528 acts as a GPIO controller.
+ - #gpio-cells		: Should be 2. The first cell is the pin number and
+			  the second cell is used to specify flags. See
+			  ../gpio/gpio.txt for more information.
+ - #clock-cells		: Should be 0.
+ - regulators:		: List of child nodes that specify the regulators.
+			  Please see ../regulator/rohm,bd70528-regulator.txt
+
+Optional properties:
+ - clock-output-names	: Should contain name for output clock.
+
+Example:
+/* External oscillator */
+osc: oscillator {
+	compatible = "fixed-clock";
+	#clock-cells = <1>;
+	clock-frequency  = <32768>;
+	clock-output-names = "osc";
+};
+
+pmic: pmic@4b {
+	compatible = "rohm,bd70528";
+	reg = <0x4b>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+	clocks = <&osc 0>;
+	#clock-cells = <0>;
+	clock-output-names = "bd70528-32k-out";
+	#gpio-cells = <2>;
+	gpio-controller;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+
+	regulators {
+		buck1: BUCK1 {
+			regulator-name = "buck1";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-boot-on;
+			regulator-ramp-delay = <125>;
+		};
+		buck2: BUCK2 {
+			regulator-name = "buck2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+			regulator-ramp-delay = <125>;
+		};
+		buck3: BUCK3 {
+			regulator-name = "buck3";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+			regulator-ramp-delay = <250>;
+		};
+		ldo1: LDO1 {
+			regulator-name = "ldo1";
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+		};
+		ldo2: LDO2 {
+			regulator-name = "ldo2";
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+		};
+
+		ldo3: LDO3 {
+			regulator-name = "ldo3";
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <3300000>;
+		};
+		led_ldo1: LED_LDO1 {
+			regulator-name = "led_ldo1";
+			regulator-min-microvolt = <200000>;
+			regulator-max-microvolt = <300000>;
+		};
+		led_ldo2: LED_LDO2 {
+			regulator-name = "led_ldo2";
+			regulator-min-microvolt = <200000>;
+			regulator-max-microvolt = <300000>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml
new file mode 100644
index 000000000..3a6a1a26e
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml
@@ -0,0 +1,198 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rohm,bd71828-pmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD71828 Power Management Integrated Circuit bindings
+
+maintainers:
+  - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description: |
+  BD71828GW is a single-chip power management IC for battery-powered portable
+  devices. The IC integrates 7 buck converters, 7 LDOs, and a 1500 mA
+  single-cell linear charger. Also included is a Coulomb counter, a real-time
+  clock (RTC), and a 32.768 kHz clock gate.
+
+properties:
+  compatible:
+    const: rohm,bd71828
+
+  reg:
+    description:
+      I2C slave address.
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  gpio-controller: true
+
+  "#gpio-cells":
+    const: 2
+    description: |
+      The first cell is the pin number and the second cell is used to specify
+      flags. See ../gpio/gpio.txt for more information.
+
+  clocks:
+    maxItems: 1
+
+  "#clock-cells":
+    const: 0
+
+  clock-output-names:
+    const: bd71828-32k-out
+
+  rohm,charger-sense-resistor-ohms:
+    minimum: 10000000
+    maximum: 50000000
+    description: |
+      BD71827 and BD71828 have SAR ADC for measuring charging currents.
+      External sense resistor (RSENSE in data sheet) should be used. If some
+      other but 30MOhm resistor is used the resistance value should be given
+      here in Ohms.
+
+  regulators:
+    $ref: ../regulator/rohm,bd71828-regulator.yaml
+    description:
+      List of child nodes that specify the regulators.
+
+  leds:
+    $ref: ../leds/rohm,bd71828-leds.yaml
+
+  gpio-reserved-ranges:
+    description: |
+      Usage of BD71828 GPIO pins can be changed via OTP. This property can be
+      used to mark the pins which should not be configured for GPIO. Please see
+      the ../gpio/gpio.txt for more information.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - "#clock-cells"
+  - regulators
+  - gpio-controller
+  - "#gpio-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/leds/common.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pmic: pmic@4b {
+            compatible = "rohm,bd71828";
+            reg = <0x4b>;
+
+            interrupt-parent = <&gpio1>;
+            interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+
+            clocks = <&osc 0>;
+            #clock-cells = <0>;
+            clock-output-names = "bd71828-32k-out";
+
+            gpio-controller;
+            #gpio-cells = <2>;
+            gpio-reserved-ranges = <0 1>, <2 1>;
+
+            rohm,charger-sense-resistor-ohms = <10000000>;
+
+            regulators {
+                buck1: BUCK1 {
+                    regulator-name = "buck1";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <2000000>;
+                    regulator-ramp-delay = <2500>;
+                };
+                buck2: BUCK2 {
+                    regulator-name = "buck2";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <2000000>;
+                    regulator-ramp-delay = <2500>;
+                };
+                buck3: BUCK3 {
+                    regulator-name = "buck3";
+                    regulator-min-microvolt = <1200000>;
+                    regulator-max-microvolt = <2000000>;
+                };
+                buck4: BUCK4 {
+                    regulator-name = "buck4";
+                    regulator-min-microvolt = <1000000>;
+                    regulator-max-microvolt = <1800000>;
+                };
+                buck5: BUCK5 {
+                    regulator-name = "buck5";
+                    regulator-min-microvolt = <2500000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                buck6: BUCK6 {
+                    regulator-name = "buck6";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <2000000>;
+                    regulator-ramp-delay = <2500>;
+                };
+                buck7: BUCK7 {
+                    regulator-name = "buck7";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <2000000>;
+                    regulator-ramp-delay = <2500>;
+                };
+                ldo1: LDO1 {
+                    regulator-name = "ldo1";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                ldo2: LDO2 {
+                    regulator-name = "ldo2";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                ldo3: LDO3 {
+                    regulator-name = "ldo3";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                ldo4: LDO4 {
+                    regulator-name = "ldo4";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                ldo5: LDO5 {
+                    regulator-name = "ldo5";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                ldo6: LDO6 {
+                    regulator-name = "ldo6";
+                    regulator-min-microvolt = <1800000>;
+                    regulator-max-microvolt = <1800000>;
+                };
+                ldo7_reg: LDO7 {
+                    regulator-name = "ldo7";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+            };
+
+            leds {
+                compatible = "rohm,bd71828-leds";
+
+                led-1 {
+                    rohm,led-compatible = "bd71828-grnled";
+                    function = LED_FUNCTION_INDICATOR;
+                    color = <LED_COLOR_ID_GREEN>;
+                };
+                led-2 {
+                    rohm,led-compatible = "bd71828-ambled";
+                    function = LED_FUNCTION_CHARGING;
+                    color = <LED_COLOR_ID_AMBER>;
+                };
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.yaml
new file mode 100644
index 000000000..65018a019
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.yaml
@@ -0,0 +1,238 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rohm,bd71837-pmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD71837 Power Management Integrated Circuit bindings
+
+maintainers:
+  - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description: |
+  BD71837MWV is programmable Power Management ICs for powering single-core,
+  dual-core, and quad-core SoCs such as NXP-i.MX 8M. It is optimized for low
+  BOM cost and compact solution footprint. BD71837MWV  integrates 8 Buck
+  regulators and 7 LDOs.
+  Datasheet for BD71837 is available at
+  https://www.rohm.com/products/power-management/power-management-ic-for-system/industrial-consumer-applications/nxp-imx/bd71837amwv-product
+
+properties:
+  compatible:
+    const: rohm,bd71837
+
+  reg:
+    description:
+      I2C slave address.
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  "#clock-cells":
+    const: 0
+
+# The BD718x7 supports two different HW states as reset target states. States
+# are called as SNVS and READY. At READY state all the PMIC power outputs go
+# down and OTP is reload. At the SNVS state all other logic and external
+# devices apart from the SNVS power domain are shut off. Please refer to NXP
+# i.MX8 documentation for further information regarding SNVS state. When a
+# reset is done via SNVS state the PMIC OTP data is not reload. This causes
+# power outputs that have been under SW control to stay down when reset has
+# switched power state to SNVS. If reset is done via READY state the power
+# outputs will be returned to HW control by OTP loading. Thus the reset
+# target state is set to READY by default. If SNVS state is used the boot
+# crucial regulators must have the regulator-always-on and regulator-boot-on
+# properties set in regulator node.
+
+  rohm,reset-snvs-powered:
+    description: |
+      Transfer PMIC to SNVS state at reset
+    type: boolean
+
+# Configure the "short press" and "long press" timers for the power button.
+# Values are rounded to what hardware supports
+# Short-press:
+#   Shortest being 10ms, next 500ms and then multiple of 500ms up to 7,5s
+# Long-press:
+#   Shortest being 10ms, next 1000ms and then multiple of 1000ms up to 15s
+# If these properties are not present the existing configuration (from
+# bootloader or OTP) is not touched.
+
+  rohm,short-press-ms:
+    description:
+      Short press duration in milliseconds
+    enum:
+      - 10
+      - 500
+      - 1000
+      - 1500
+      - 2000
+      - 2500
+      - 3000
+      - 3500
+      - 4000
+      - 4500
+      - 5000
+      - 5500
+      - 6000
+      - 6500
+      - 7000
+
+  rohm,long-press-ms:
+    description:
+      Long press duration in milliseconds
+    enum:
+      - 10
+      - 1000
+      - 2000
+      - 3000
+      - 4000
+      - 5000
+      - 6000
+      - 7000
+      - 8000
+      - 9000
+      - 10000
+      - 11000
+      - 12000
+      - 13000
+      - 14000
+
+  regulators:
+    $ref: ../regulator/rohm,bd71837-regulator.yaml
+    description:
+      List of child nodes that specify the regulators.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - "#clock-cells"
+  - regulators
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/leds/common.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pmic: pmic@4b {
+            compatible = "rohm,bd71837";
+            reg = <0x4b>;
+            interrupt-parent = <&gpio1>;
+            interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+            #clock-cells = <0>;
+            clocks = <&osc 0>;
+            rohm,reset-snvs-powered;
+            rohm,short-press-ms = <10>;
+            rohm,long-press-ms = <2000>;
+
+            regulators {
+                buck1: BUCK1 {
+                    regulator-name = "buck1";
+                    regulator-min-microvolt = <700000>;
+                    regulator-max-microvolt = <1300000>;
+                    regulator-boot-on;
+                    regulator-always-on;
+                    regulator-ramp-delay = <1250>;
+                    rohm,dvs-run-voltage = <900000>;
+                    rohm,dvs-idle-voltage = <850000>;
+                    rohm,dvs-suspend-voltage = <800000>;
+                };
+                buck2: BUCK2 {
+                    regulator-name = "buck2";
+                    regulator-min-microvolt = <700000>;
+                    regulator-max-microvolt = <1300000>;
+                    regulator-boot-on;
+                    regulator-always-on;
+                    regulator-ramp-delay = <1250>;
+                    rohm,dvs-run-voltage = <1000000>;
+                    rohm,dvs-idle-voltage = <900000>;
+                };
+                buck3: BUCK3 {
+                    regulator-name = "buck3";
+                    regulator-min-microvolt = <700000>;
+                    regulator-max-microvolt = <1300000>;
+                    regulator-boot-on;
+                    rohm,dvs-run-voltage = <1000000>;
+                };
+                buck4: BUCK4 {
+                    regulator-name = "buck4";
+                    regulator-min-microvolt = <700000>;
+                    regulator-max-microvolt = <1300000>;
+                    regulator-boot-on;
+                    rohm,dvs-run-voltage = <1000000>;
+                };
+                buck5: BUCK5 {
+                    regulator-name = "buck5";
+                    regulator-min-microvolt = <700000>;
+                    regulator-max-microvolt = <1350000>;
+                    regulator-boot-on;
+                };
+                buck6: BUCK6 {
+                    regulator-name = "buck6";
+                    regulator-min-microvolt = <3000000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-boot-on;
+                };
+                buck7: BUCK7 {
+                    regulator-name = "buck7";
+                    regulator-min-microvolt = <1605000>;
+                    regulator-max-microvolt = <1995000>;
+                    regulator-boot-on;
+                };
+                buck8: BUCK8 {
+                    regulator-name = "buck8";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <1400000>;
+                };
+
+                ldo1: LDO1 {
+                    regulator-name = "ldo1";
+                    regulator-min-microvolt = <3000000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-boot-on;
+                };
+                ldo2: LDO2 {
+                    regulator-name = "ldo2";
+                    regulator-min-microvolt = <900000>;
+                    regulator-max-microvolt = <900000>;
+                    regulator-boot-on;
+                };
+                ldo3: LDO3 {
+                    regulator-name = "ldo3";
+                    regulator-min-microvolt = <1800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                ldo4: LDO4 {
+                    regulator-name = "ldo4";
+                    regulator-min-microvolt = <900000>;
+                    regulator-max-microvolt = <1800000>;
+                };
+                ldo5: LDO5 {
+                    regulator-name = "ldo5";
+                    regulator-min-microvolt = <1800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                ldo6: LDO6 {
+                    regulator-name = "ldo6";
+                    regulator-min-microvolt = <900000>;
+                    regulator-max-microvolt = <1800000>;
+                };
+                ldo7_reg: LDO7 {
+                    regulator-name = "ldo7";
+                    regulator-min-microvolt = <1800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71847-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71847-pmic.yaml
new file mode 100644
index 000000000..5d531051a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd71847-pmic.yaml
@@ -0,0 +1,229 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rohm,bd71847-pmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD71847 and BD71850 Power Management Integrated Circuit bindings
+
+maintainers:
+  - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description: |
+  BD71847AMWV and BD71850MWV are programmable Power Management ICs for powering
+  single-core,  dual-core, and quad-core SoCs such as NXP-i.MX 8M. It is
+  optimized for low BOM cost and compact solution footprint. BD71847MWV and
+  BD71850MWV integrate 6 Buck regulators and 6 LDOs.
+  Datasheets are available at
+  https://www.rohm.com/products/power-management/power-management-ic-for-system/industrial-consumer-applications/nxp-imx/bd71847amwv-product
+  https://www.rohm.com/products/power-management/power-management-ic-for-system/industrial-consumer-applications/nxp-imx/bd71850mwv-product
+
+properties:
+  compatible:
+    enum:
+      - rohm,bd71847
+      - rohm,bd71850
+
+  reg:
+    description:
+      I2C slave address.
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  "#clock-cells":
+    const: 0
+
+  clock-output-names:
+    maxItems: 1
+
+# The BD71847 abd BD71850 support two different HW states as reset target
+# states. States are called as SNVS and READY. At READY state all the PMIC
+# power outputs go down and OTP is reload. At the SNVS state all other logic
+# and external devices apart from the SNVS power domain are shut off. Please
+# refer to NXP i.MX8 documentation for further information regarding SNVS
+# state. When a reset is done via SNVS state the PMIC OTP data is not reload.
+# This causes power outputs that have been under SW control to stay down when
+# reset has switched power state to SNVS. If reset is done via READY state the
+# power outputs will be returned to HW control by OTP loading. Thus the reset
+# target state is set to READY by default. If SNVS state is used the boot
+# crucial regulators must have the regulator-always-on and regulator-boot-on
+# properties set in regulator node.
+
+  rohm,reset-snvs-powered:
+    description:
+      Transfer PMIC to SNVS state at reset.
+    type: boolean
+
+# Configure the "short press" and "long press" timers for the power button.
+# Values are rounded to what hardware supports
+# Short-press:
+#   Shortest being 10ms, next 500ms and then multiple of 500ms up to 7,5s
+# Long-press:
+#   Shortest being 10ms, next 1000ms and then multiple of 1000ms up to 15s
+# If these properties are not present the existing # configuration (from
+# bootloader or OTP) is not touched.
+
+  rohm,short-press-ms:
+    description:
+      Short press duration in milliseconds
+    enum:
+      - 10
+      - 500
+      - 1000
+      - 1500
+      - 2000
+      - 2500
+      - 3000
+      - 3500
+      - 4000
+      - 4500
+      - 5000
+      - 5500
+      - 6000
+      - 6500
+      - 7000
+      - 7500
+
+  rohm,long-press-ms:
+    description:
+      Long press duration in milliseconds
+    enum:
+      - 10
+      - 1000
+      - 2000
+      - 3000
+      - 4000
+      - 5000
+      - 6000
+      - 7000
+      - 8000
+      - 9000
+      - 10000
+      - 11000
+      - 12000
+      - 13000
+      - 14000
+      - 15000
+
+  regulators:
+    $ref: ../regulator/rohm,bd71847-regulator.yaml
+    description:
+      List of child nodes that specify the regulators.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - regulators
+
+additionalProperties: false
+
+dependencies:
+  '#clock-cells': [clocks]
+  clocks: ['#clock-cells']
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/leds/common.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pmic: pmic@4b {
+            compatible = "rohm,bd71847";
+            reg = <0x4b>;
+            interrupt-parent = <&gpio1>;
+            interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+            #clock-cells = <0>;
+            clocks = <&osc 0>;
+            rohm,reset-snvs-powered;
+            rohm,short-press-ms = <10>;
+            rohm,long-press-ms = <2000>;
+
+            regulators {
+                buck1: BUCK1 {
+                    regulator-name = "buck1";
+                    regulator-min-microvolt = <700000>;
+                    regulator-max-microvolt = <1300000>;
+                    regulator-boot-on;
+                    regulator-always-on;
+                    regulator-ramp-delay = <1250>;
+                    rohm,dvs-run-voltage = <900000>;
+                    rohm,dvs-idle-voltage = <850000>;
+                    rohm,dvs-suspend-voltage = <800000>;
+                };
+                buck2: BUCK2 {
+                    regulator-name = "buck2";
+                    regulator-min-microvolt = <700000>;
+                    regulator-max-microvolt = <1300000>;
+                    regulator-boot-on;
+                    regulator-always-on;
+                    regulator-ramp-delay = <1250>;
+                    rohm,dvs-run-voltage = <1000000>;
+                    rohm,dvs-idle-voltage = <900000>;
+                };
+                buck3: BUCK3 {
+                    regulator-name = "buck3";
+                    regulator-min-microvolt = <550000>;
+                    regulator-max-microvolt = <1350000>;
+                    regulator-boot-on;
+                };
+                buck4: BUCK4 {
+                    regulator-name = "buck4";
+                    regulator-min-microvolt = <2600000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-boot-on;
+                };
+                buck5: BUCK5 {
+                    regulator-name = "buck5";
+                    regulator-min-microvolt = <1605000>;
+                    regulator-max-microvolt = <1995000>;
+                    regulator-boot-on;
+                };
+                buck8: BUCK6 {
+                    regulator-name = "buck6";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <1400000>;
+                };
+
+                ldo1: LDO1 {
+                    regulator-name = "ldo1";
+                    regulator-min-microvolt = <1600000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-boot-on;
+                };
+                ldo2: LDO2 {
+                    regulator-name = "ldo2";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <900000>;
+                    regulator-boot-on;
+                };
+                ldo3: LDO3 {
+                    regulator-name = "ldo3";
+                    regulator-min-microvolt = <1800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                ldo4: LDO4 {
+                    regulator-name = "ldo4";
+                    regulator-min-microvolt = <900000>;
+                    regulator-max-microvolt = <1800000>;
+                };
+                ldo5: LDO5 {
+                    regulator-name = "ldo5";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                ldo6: LDO6 {
+                    regulator-name = "ldo6";
+                    regulator-min-microvolt = <900000>;
+                    regulator-max-microvolt = <1800000>;
+                };
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt b/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt
new file mode 100644
index 000000000..30ea27c39
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt
@@ -0,0 +1,72 @@
+Samsung Exynos SoC Low Power Audio Subsystem (LPASS)
+
+Required properties:
+
+ - compatible		: "samsung,exynos5433-lpass"
+ - reg			: should contain the LPASS top SFR region location
+			  and size
+ - clock-names		: should contain following required clocks: "sfr0_ctrl"
+ - clocks		: should contain clock specifiers of all clocks, which
+			  input names have been specified in clock-names
+			  property, in same order.
+ - #address-cells	: should be 1
+ - #size-cells		: should be 1
+ - ranges		: must be present
+
+Each IP block of the Low Power Audio Subsystem should be specified as
+an optional sub-node. For "samsung,exynos5433-lpass" compatible this includes:
+UART, SLIMBUS, PCM, I2S, DMAC, Timers 0...4, VIC, WDT 0...1 devices.
+
+Bindings of the sub-nodes are described in:
+  ../serial/samsung_uart.yaml
+  ../sound/samsung-i2s.txt
+  ../dma/arm-pl330.txt
+
+
+Example:
+
+audio-subsystem {
+	compatible = "samsung,exynos5433-lpass";
+	reg = <0x11400000 0x100>, <0x11500000 0x08>;
+	clocks = <&cmu_aud CLK_PCLK_SFR0_CTRL>;
+	clock-names = "sfr0_ctrl";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	adma: adma@11420000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x11420000 0x1000>;
+		interrupts = <0 73 0>;
+		clocks = <&cmu_aud CLK_ACLK_DMAC>;
+		clock-names = "apb_pclk";
+		#dma-cells = <1>;
+		#dma-channels = <8>;
+		#dma-requests = <32>;
+	};
+
+	i2s0: i2s0@11440000 {
+		compatible = "samsung,exynos7-i2s";
+		reg = <0x11440000 0x100>;
+		dmas = <&adma 0 &adma 2>;
+		dma-names = "tx", "rx";
+		interrupts = <0 70 0>;
+		clocks = <&cmu_aud CLK_PCLK_AUD_I2S>,
+			 <&cmu_aud CLK_SCLK_AUD_I2S>,
+			 <&cmu_aud CLK_SCLK_I2S_BCLK>;
+		clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s0_bus>;
+	};
+
+	serial_3: serial@11460000 {
+		compatible = "samsung,exynos5433-uart";
+		reg = <0x11460000 0x100>;
+		interrupts = <0 67 0>;
+		clocks = <&cmu_aud CLK_PCLK_AUD_UART>,
+			 <&cmu_aud CLK_SCLK_AUD_UART>;
+		clock-names = "uart", "clk_uart_baud0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart_aud_bus>;
+	};
+ };
diff --git a/Documentation/devicetree/bindings/mfd/samsung,sec-core.txt b/Documentation/devicetree/bindings/mfd/samsung,sec-core.txt
new file mode 100644
index 000000000..c68cdd365
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/samsung,sec-core.txt
@@ -0,0 +1,86 @@
+Binding for Samsung S2M and S5M family multi-function device
+============================================================
+
+This is a part of device tree bindings for S2M and S5M family multi-function
+devices.
+
+The Samsung S2MPA01, S2MPS11/13/14/15, S2MPU02 and S5M8767 is a family
+of multi-function devices which include voltage and current regulators, RTC,
+charger controller, clock outputs and other sub-blocks. It is interfaced
+to the host controller using an I2C interface. Each sub-block is usually
+addressed by the host system using different I2C slave addresses.
+
+
+This document describes bindings for main device node. Optional sub-blocks
+must be a sub-nodes to it. Bindings for them can be found in:
+ - bindings/regulator/samsung,s2mpa01.txt
+ - bindings/regulator/samsung,s2mps11.txt
+ - bindings/regulator/samsung,s5m8767.txt
+ - bindings/clock/samsung,s2mps11.txt
+
+
+Required properties:
+ - compatible: Should be one of the following
+	- "samsung,s2mpa01-pmic",
+	- "samsung,s2mps11-pmic",
+	- "samsung,s2mps13-pmic",
+	- "samsung,s2mps14-pmic",
+	- "samsung,s2mps15-pmic",
+	- "samsung,s2mpu02-pmic",
+	- "samsung,s5m8767-pmic".
+ - reg: Specifies the I2C slave address of the pmic block. It should be 0x66.
+
+Optional properties:
+ - interrupts: Interrupt specifiers for interrupt sources.
+ - samsung,s2mps11-wrstbi-ground: Indicates that WRSTBI pin of PMIC is pulled
+   down. When the system is suspended it will always go down thus triggerring
+   unwanted buck warm reset (setting buck voltages to default values).
+ - samsung,s2mps11-acokb-ground: Indicates that ACOKB pin of S2MPS11 PMIC is
+   connected to the ground so the PMIC must manually set PWRHOLD bit in CTRL1
+   register to turn off the power. Usually the ACOKB is pulled up to VBATT so
+   when PWRHOLD pin goes low, the rising ACOKB will trigger power off.
+
+Example:
+
+	s2mps11_pmic@66 {
+		compatible = "samsung,s2mps11-pmic";
+		reg = <0x66>;
+
+		s2m_osc: clocks {
+			compatible = "samsung,s2mps11-clk";
+			#clock-cells = <1>;
+			clock-output-names = "xx", "yy", "zz";
+		};
+
+		regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "VDD_ABB_3.3V";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "VDD_ALIVE_1.1V";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "vdd_mif";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-ramp-delay = <50000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/sky81452.txt b/Documentation/devicetree/bindings/mfd/sky81452.txt
new file mode 100644
index 000000000..511764acd
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/sky81452.txt
@@ -0,0 +1,35 @@
+SKY81452 bindings
+
+Required properties:
+- compatible	: Must be "skyworks,sky81452"
+- reg		: I2C slave address
+
+Required child nodes:
+- backlight	: container node for backlight following the binding
+		in leds/backlight/sky81452-backlight.txt
+- regulator	: container node for regulators following the binding
+		in regulator/sky81452-regulator.txt
+
+Example:
+
+	sky81452@2c {
+		compatible = "skyworks,sky81452";
+		reg = <0x2c>;
+
+		backlight {
+			compatible = "skyworks,sky81452-backlight";
+			name = "pwm-backlight";
+			led-sources = <0 1 2 3 6>;
+			skyworks,ignore-pwm;
+			skyworks,phase-shift;
+			skyworks,current-limit = <2300>;
+		};
+
+		regulator {
+			lout {
+				regulator-name = "sky81452-lout";
+				regulator-min-microvolt = <4500000>;
+				regulator-max-microvolt = <8000000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/sprd,sc27xx-pmic.txt b/Documentation/devicetree/bindings/mfd/sprd,sc27xx-pmic.txt
new file mode 100644
index 000000000..21b9a897f
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/sprd,sc27xx-pmic.txt
@@ -0,0 +1,40 @@
+Spreadtrum SC27xx Power Management Integrated Circuit (PMIC)
+
+The Spreadtrum SC27xx series PMICs contain SC2720, SC2721, SC2723, SC2730
+and SC2731. The Spreadtrum PMIC belonging to SC27xx series integrates all
+mobile handset power management, audio codec, battery management and user
+interface support function in a single chip. It has 6 major functional
+blocks:
+- DCDCs to support CPU, memory.
+- LDOs to support both internal and external requirement.
+- Battery management system, such as charger, fuel gauge.
+- Audio codec.
+- User interface function, such as indicator, flash LED and so on.
+- IC level interface, such as power on/off control, RTC and typec and so on.
+
+Required properties:
+- compatible: Should be one of the following:
+	"sprd,sc2720"
+	"sprd,sc2721"
+	"sprd,sc2723"
+	"sprd,sc2730"
+	"sprd,sc2731"
+- reg: The address of the device chip select, should be 0.
+- spi-max-frequency: Typically set to 26000000.
+- interrupts: The interrupt line the device is connected to.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: The number of cells to describe an PMIC IRQ, must be 2.
+- #address-cells: Child device offset number of cells, must be 1.
+- #size-cells: Child device size number of cells, must be 0.
+
+Example:
+pmic@0 {
+	compatible = "sprd,sc2731";
+	reg = <0>;
+	spi-max-frequency = <26000000>;
+	interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
diff --git a/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml b/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml
new file mode 100644
index 000000000..8bcea8dd7
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml
@@ -0,0 +1,141 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/st,stm32-lptimer.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics STM32 Low-Power Timers bindings
+
+description: |
+  The STM32 Low-Power Timer (LPTIM) is a 16-bit timer that provides several
+  functions
+   - PWM output (with programmable prescaler, configurable polarity)
+   - Trigger source for STM32 ADC/DAC (LPTIM_OUT)
+   - Several counter modes:
+     - quadrature encoder to detect angular position and direction of rotary
+       elements, from IN1 and IN2 input signals.
+     - simple counter from IN1 input signal.
+
+maintainers:
+  - Fabrice Gasnier <fabrice.gasnier@st.com>
+
+properties:
+  compatible:
+    const: st,stm32-lptimer
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: mux
+
+  interrupts:
+    maxItems: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  wakeup-source: true
+
+  pwm:
+    type: object
+
+    properties:
+      compatible:
+        const: st,stm32-pwm-lp
+
+      "#pwm-cells":
+        const: 3
+
+    required:
+      - "#pwm-cells"
+      - compatible
+
+patternProperties:
+  "^trigger@[0-9]+$":
+    type: object
+
+    properties:
+      compatible:
+        const: st,stm32-lptimer-trigger
+
+      reg:
+        description: Identify trigger hardware block.
+        items:
+          minimum: 0
+          maximum: 2
+
+    required:
+      - compatible
+      - reg
+
+  counter:
+    type: object
+
+    properties:
+      compatible:
+        const: st,stm32-lptimer-counter
+
+    required:
+      - compatible
+
+  timer:
+    type: object
+
+    properties:
+      compatible:
+        const: st,stm32-lptimer-timer
+
+    required:
+      - compatible
+
+required:
+  - "#address-cells"
+  - "#size-cells"
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/stm32mp1-clks.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    timer@40002400 {
+      compatible = "st,stm32-lptimer";
+      reg = <0x40002400 0x400>;
+      clocks = <&timer_clk>;
+      clock-names = "mux";
+      interrupts-extended = <&exti 47 IRQ_TYPE_LEVEL_HIGH>;
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      pwm {
+        compatible = "st,stm32-pwm-lp";
+        #pwm-cells = <3>;
+      };
+
+      trigger@0 {
+        compatible = "st,stm32-lptimer-trigger";
+        reg = <0>;
+      };
+
+      counter {
+        compatible = "st,stm32-lptimer-counter";
+      };
+
+      timer {
+        compatible = "st,stm32-lptimer-timer";
+      };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml b/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml
new file mode 100644
index 000000000..f212fc6e1
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml
@@ -0,0 +1,161 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/st,stm32-timers.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics STM32 Timers bindings
+
+description: |
+  This hardware block provides 3 types of timer along with PWM functionality:
+    - advanced-control timers consist of a 16-bit auto-reload counter driven
+      by a programmable prescaler, break input feature, PWM outputs and
+      complementary PWM outputs channels.
+    - general-purpose timers consist of a 16-bit or 32-bit auto-reload counter
+      driven by a programmable prescaler and PWM outputs.
+    - basic timers consist of a 16-bit auto-reload counter driven by a
+      programmable prescaler.
+
+maintainers:
+  - Benjamin Gaignard <benjamin.gaignard@st.com>
+  - Fabrice Gasnier <fabrice.gasnier@st.com>
+
+properties:
+  compatible:
+    const: st,stm32-timers
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: int
+
+  reset:
+    maxItems: 1
+
+  dmas:
+    minItems: 1
+    maxItems: 7
+
+  dma-names:
+    items:
+      enum: [ ch1, ch2, ch3, ch4, up, trig, com ]
+    minItems: 1
+    maxItems: 7
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  pwm:
+    type: object
+
+    properties:
+      compatible:
+        const: st,stm32-pwm
+
+      "#pwm-cells":
+        const: 3
+
+      st,breakinput:
+        description:
+          One or two <index level filter> to describe break input
+          configurations.
+        $ref: /schemas/types.yaml#/definitions/uint32-matrix
+        items:
+          items:
+            - description: |
+                "index" indicates on which break input (0 or 1) the
+                configuration should be applied.
+              enum: [0, 1]
+            - description: |
+                "level" gives the active level (0=low or 1=high) of the
+                input signal for this configuration
+              enum: [0, 1]
+            - description: |
+                "filter" gives the filtering value (up to 15) to be applied.
+              maximum: 15
+        minItems: 1
+        maxItems: 2
+
+    required:
+      - "#pwm-cells"
+      - compatible
+
+patternProperties:
+  "^timer@[0-9]+$":
+    type: object
+
+    properties:
+      compatible:
+        enum:
+          - st,stm32-timer-trigger
+          - st,stm32h7-timer-trigger
+
+      reg:
+        description: Identify trigger hardware block.
+        items:
+          minimum: 0
+          maximum: 16
+
+    required:
+      - compatible
+      - reg
+
+  counter:
+    type: object
+
+    properties:
+      compatible:
+        const: st,stm32-timer-counter
+
+    required:
+      - compatible
+
+required:
+  - "#address-cells"
+  - "#size-cells"
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/stm32mp1-clks.h>
+    timers2: timers@40000000 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      compatible = "st,stm32-timers";
+      reg = <0x40000000 0x400>;
+      clocks = <&rcc TIM2_K>;
+      clock-names = "int";
+      dmas = <&dmamux1 18 0x400 0x1>,
+             <&dmamux1 19 0x400 0x1>,
+             <&dmamux1 20 0x400 0x1>,
+             <&dmamux1 21 0x400 0x1>,
+             <&dmamux1 22 0x400 0x1>;
+      dma-names = "ch1", "ch2", "ch3", "ch4", "up";
+      pwm {
+        compatible = "st,stm32-pwm";
+        #pwm-cells = <3>;
+        st,breakinput = <0 1 5>;
+      };
+      timer@0 {
+        compatible = "st,stm32-timer-trigger";
+        reg = <0>;
+      };
+      counter {
+        compatible = "st,stm32-timer-counter";
+      };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mfd/st,stmfx.yaml b/Documentation/devicetree/bindings/mfd/st,stmfx.yaml
new file mode 100644
index 000000000..888ab4b5d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/st,stmfx.yaml
@@ -0,0 +1,122 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/st,stmfx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectonics Multi-Function eXpander (STMFX) bindings
+
+description: ST Multi-Function eXpander (STMFX) is a slave controller using I2C for
+               communication with the main MCU. Its main features are GPIO expansion,
+               main MCU IDD measurement (IDD is the amount of current that flows
+               through VDD) and resistive touchscreen controller.
+
+maintainers:
+  - Amelie Delaunay <amelie.delaunay@st.com>
+
+properties:
+  compatible:
+    const: st,stmfx-0300
+
+  reg:
+    enum: [ 0x42, 0x43 ]
+
+  interrupts:
+    maxItems: 1
+
+  drive-open-drain: true
+
+  vdd-supply:
+    maxItems: 1
+
+  pinctrl:
+    type: object
+
+    properties:
+      compatible:
+        const: st,stmfx-0300-pinctrl
+
+      "#gpio-cells":
+        const: 2
+
+      "#interrupt-cells":
+        const: 2
+
+      gpio-controller: true
+
+      interrupt-controller: true
+
+      gpio-ranges:
+        description: if all STMFX pins[24:0] are available (no other STMFX function in use),
+                     you should use gpio-ranges = <&stmfx_pinctrl 0 0 24>;
+                     if agpio[3:0] are not available (STMFX Touchscreen function in use),
+                     you should use gpio-ranges = <&stmfx_pinctrl 0 0 16>, <&stmfx_pinctrl 20 20 4>;
+                     if agpio[7:4] are not available (STMFX IDD function in use),
+                     you should use gpio-ranges = <&stmfx_pinctrl 0 0 20>;
+        maxItems: 1
+
+    patternProperties:
+      "^[a-zA-Z]*-pins$":
+        type: object
+
+        allOf:
+          - $ref: ../pinctrl/pinmux-node.yaml
+
+        properties:
+          pins: true
+          bias-disable: true
+          bias-pull-up: true
+          bias-pull-pin-default: true
+          bias-pull-down: true
+          drive-open-drain: true
+          drive-push-pull: true
+          output-high: true
+          output-low: true
+
+    additionalProperties: false
+
+    required:
+      - compatible
+      - "#gpio-cells"
+      - "#interrupt-cells"
+      - gpio-controller
+      - interrupt-controller
+      - gpio-ranges
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      stmfx@42 {
+        compatible = "st,stmfx-0300";
+        reg = <0x42>;
+        interrupts = <8 IRQ_TYPE_EDGE_RISING>;
+        interrupt-parent = <&gpioi>;
+        vdd-supply = <&v3v3>;
+
+        stmfx_pinctrl: pinctrl {
+          compatible = "st,stmfx-0300-pinctrl";
+          #gpio-cells = <2>;
+          #interrupt-cells = <2>;
+          gpio-controller;
+          interrupt-controller;
+          gpio-ranges = <&stmfx_pinctrl 0 0 24>;
+
+          joystick_pins: joystick-pins {
+            pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
+            drive-push-pull;
+            bias-pull-up;
+          };
+        };
+      };
+    };
+...
diff --git a/Documentation/devicetree/bindings/mfd/st,stpmic1.yaml b/Documentation/devicetree/bindings/mfd/st,stpmic1.yaml
new file mode 100644
index 000000000..305123e74
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/st,stpmic1.yaml
@@ -0,0 +1,334 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/st,stpmic1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectonics STPMIC1 Power Management IC bindings
+
+description: STMicroelectronics STPMIC1 Power Management IC
+
+maintainers:
+  - pascal Paillet <p.paillet@st.com>
+
+properties:
+  compatible:
+    const: st,stpmic1
+
+  reg:
+    const: 0x33
+
+  interrupts:
+    maxItems: 1
+
+  "#interrupt-cells":
+    const: 2
+
+  interrupt-controller: true
+
+  onkey:
+    type: object
+
+    $ref: ../input/input.yaml
+
+    properties:
+      compatible:
+        const: st,stpmic1-onkey
+
+      interrupts:
+        items:
+          - description: onkey-falling, happens when onkey is pressed. IT_PONKEY_F of pmic
+          - description: onkey-rising, happens when onkey is released. IT_PONKEY_R of pmic
+
+      interrupt-names:
+        items:
+          - const: onkey-falling
+          - const: onkey-rising
+
+      st,onkey-clear-cc-flag:
+        description: onkey is able power on after an over-current shutdown event.
+        $ref: /schemas/types.yaml#/definitions/flag
+
+      st,onkey-pu-inactive:
+        description: onkey pull up is not active
+        $ref: /schemas/types.yaml#/definitions/flag
+
+      power-off-time-sec:
+        minimum: 1
+        maximum: 16
+
+    required:
+      - compatible
+      - interrupts
+      - interrupt-names
+
+    additionalProperties: false
+
+  watchdog:
+    type: object
+
+    $ref: ../watchdog/watchdog.yaml
+
+    properties:
+      compatible:
+        const: st,stpmic1-wdt
+
+      timeout-sec: true
+
+    required:
+      - compatible
+
+    additionalProperties: false
+
+  regulators:
+    type: object
+
+    description: |
+      Available Regulators in STPMIC1 device are:
+        - buck1 for Buck BUCK1
+        - buck2 for Buck BUCK2
+        - buck3 for Buck BUCK3
+        - buck4 for Buck BUCK4
+        - ldo1 for LDO LDO1
+        - ldo2 for LDO LDO2
+        - ldo3 for LDO LDO3
+        - ldo4 for LDO LDO4
+        - ldo5 for LDO LDO5
+        - ldo6 for LDO LDO6
+        - vref_ddr for LDO Vref DDR
+        - boost for Buck BOOST
+        - pwr_sw1 for VBUS_OTG switch
+        - pwr_sw2 for SW_OUT switch
+      Switches are fixed voltage regulators with only enable/disable capability.
+
+    properties:
+      compatible:
+        const: st,stpmic1-regulators
+
+      ldo3:
+        type: object
+
+        properties:
+          interrupts:
+            maxItems: 1
+
+          st,mask-reset:
+            description: mask reset for this regulator, the regulator configuration
+              is maintained during pmic reset.
+            $ref: /schemas/types.yaml#/definitions/flag
+
+          regulator-name: true
+          regulator-boot-on: true
+          regulator-always-on: true
+          regulator-min-microvolt: true
+          regulator-max-microvolt: true
+          regulator-allow-bypass: true
+          regulator-over-current-protection: true
+
+        additionalProperties: false
+
+      ldo4:
+        type: object
+
+        properties:
+          interrupts:
+            maxItems: 1
+
+          st,mask-reset:
+            description: mask reset for this regulator, the regulator configuration
+              is maintained during pmic reset.
+            $ref: /schemas/types.yaml#/definitions/flag
+
+          regulator-name: true
+          regulator-boot-on: true
+          regulator-always-on: true
+          regulator-over-current-protection: true
+
+        additionalProperties: false
+
+      vref_ddr:
+        type: object
+
+        properties:
+          interrupts:
+            maxItems: 1
+
+          st,mask-reset:
+            description: mask reset for this regulator, the regulator configuration
+              is maintained during pmic reset.
+            $ref: /schemas/types.yaml#/definitions/flag
+
+          regulator-name: true
+          regulator-boot-on: true
+          regulator-always-on: true
+
+        additionalProperties: false
+
+      boost:
+        type: object
+
+        properties:
+          interrupts:
+            maxItems: 1
+
+          st,mask-reset:
+            description: mask reset for this regulator, the regulator configuration
+              is maintained during pmic reset.
+            $ref: /schemas/types.yaml#/definitions/flag
+
+          regulator-name: true
+          regulator-boot-on: true
+          regulator-always-on: true
+          regulator-over-current-protection: true
+
+        additionalProperties: false
+
+    patternProperties:
+      "^(buck[1-4]|ldo[1-6]|boost|pwr_sw[1-2])-supply$":
+        description: STPMIC1 voltage regulators supplies
+
+      "^(buck[1-4]|ldo[1-6]|boost|vref_ddr|pwr_sw[1-2])$":
+        $ref: ../regulator/regulator.yaml
+
+      "^ldo[1-2,5-6]$":
+        type: object
+
+        properties:
+          interrupts:
+            maxItems: 1
+
+          st,mask-reset:
+            description: mask reset for this regulator, the regulator configuration
+              is maintained during pmic reset.
+            $ref: /schemas/types.yaml#/definitions/flag
+
+          regulator-name: true
+          regulator-boot-on: true
+          regulator-always-on: true
+          regulator-min-microvolt: true
+          regulator-max-microvolt: true
+          regulator-over-current-protection: true
+          regulator-enable-ramp-delay: true
+
+        additionalProperties: false
+
+      "^buck[1-4]$":
+        type: object
+
+        properties:
+          interrupts:
+            maxItems: 1
+
+          st,mask-reset:
+            description: mask reset for this regulator, the regulator configuration
+              is maintained during pmic reset.
+            $ref: /schemas/types.yaml#/definitions/flag
+
+          regulator-name: true
+          regulator-boot-on: true
+          regulator-always-on: true
+          regulator-min-microvolt: true
+          regulator-max-microvolt: true
+          regulator-initial-mode: true
+          regulator-pull-down: true
+          regulator-over-current-protection: true
+          regulator-enable-ramp-delay: true
+
+        additionalProperties: false
+
+      "^pwr_sw[1-2]$":
+        type: object
+
+        properties:
+          interrupts:
+            maxItems: 1
+
+          regulator-name: true
+          regulator-boot-on: true
+          regulator-always-on: true
+          regulator-over-current-protection: true
+          regulator-active-discharge: true
+
+        additionalProperties: false
+
+    required:
+      - compatible
+
+    additionalProperties: false
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - "#interrupt-cells"
+  - interrupt-controller
+
+examples:
+  - |
+    #include <dt-bindings/mfd/st,stpmic1.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      pmic@33 {
+        compatible = "st,stpmic1";
+        reg = <0x33>;
+        interrupt-parent = <&gpioa>;
+        interrupts = <0 2>;
+
+        interrupt-controller;
+        #interrupt-cells = <2>;
+
+        onkey {
+          compatible = "st,stpmic1-onkey";
+          interrupts = <IT_PONKEY_F 0>,<IT_PONKEY_R 1>;
+          interrupt-names = "onkey-falling", "onkey-rising";
+          power-off-time-sec = <10>;
+        };
+
+        watchdog {
+          compatible = "st,stpmic1-wdt";
+        };
+
+        regulators {
+          compatible = "st,stpmic1-regulators";
+
+          ldo6-supply = <&v3v3>;
+
+          buck1 {
+            regulator-name = "vdd_core";
+            interrupts = <IT_CURLIM_BUCK1 0>;
+            st,mask-reset;
+            regulator-boot-on;
+            regulator-min-microvolt = <700000>;
+            regulator-max-microvolt = <1200000>;
+          };
+
+          buck3 {
+            regulator-name = "vdd";
+            regulator-min-microvolt = <3300000>;
+            regulator-max-microvolt = <3300000>;
+            regulator-boot-on;
+            regulator-pull-down;
+          };
+
+          buck4 {
+            regulator-name = "v3v3";
+            interrupts = <IT_CURLIM_BUCK4 0>;
+            regulator-min-microvolt = <3300000>;
+            regulator-max-microvolt = <3300000>;
+          };
+
+          ldo6 {
+            regulator-name = "v1v8";
+            regulator-min-microvolt = <1800000>;
+            regulator-max-microvolt = <1800000>;
+            regulator-over-current-protection;
+          };
+        };
+      };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt
new file mode 100644
index 000000000..d4408a417
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/stmpe.txt
@@ -0,0 +1,42 @@
+* ST Microelectronics STMPE Multi-Functional Device
+
+STMPE is an MFD device which may expose the following inbuilt devices: gpio,
+keypad, touchscreen, adc, pwm, rotator.
+
+Required properties:
+ - compatible			: "st,stmpe[610|801|811|1600|1601|2401|2403]"
+ - reg				: I2C/SPI address of the device
+
+Optional properties:
+ - interrupts			: The interrupt outputs from the controller
+ - interrupt-controller		: Marks the device node as an interrupt controller
+ - wakeup-source		: Marks the input device as wakable
+ - st,autosleep-timeout		: Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024
+ - irq-gpio			: If present, which GPIO to use for event IRQ
+
+Optional properties for devices with touch and ADC (STMPE811|STMPE610):
+ - st,sample-time		: ADC conversion time in number of clock.
+					0 -> 36 clocks		4 -> 80 clocks (recommended)
+					1 -> 44 clocks		5 -> 96 clocks
+					2 -> 56 clocks		6 -> 124 clocks
+					3 -> 64 clocks
+ - st,mod-12b			: ADC Bit mode
+					0 -> 10bit ADC		1 -> 12bit ADC
+ - st,ref-sel			: ADC reference source
+					0 -> internal		1 -> external
+ - st,adc-freq			: ADC Clock speed
+					0 -> 1.625 MHz		2 || 3 -> 6.5 MHz
+					1 -> 3.25 MHz
+
+Example:
+
+	stmpe1601: stmpe1601@40 {
+		compatible = "st,stmpe1601";
+		reg = <0x40>;
+		interrupts = <26 0x4>;
+		interrupt-parent = <&gpio6>;
+		interrupt-controller;
+
+		wakeup-source;
+		st,autosleep-timeout = <1024>;
+	};
diff --git a/Documentation/devicetree/bindings/mfd/syscon.yaml b/Documentation/devicetree/bindings/mfd/syscon.yaml
new file mode 100644
index 000000000..8f4764a9e
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/syscon.yaml
@@ -0,0 +1,94 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/syscon.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: System Controller Registers R/W Device Tree Bindings
+
+description: |
+  System controller node represents a register region containing a set
+  of miscellaneous registers. The registers are not cohesive enough to
+  represent as any specific type of device. The typical use-case is
+  for some other node's driver, or platform-specific code, to acquire
+  a reference to the syscon node (e.g. by phandle, node path, or
+  search using a specific compatible value), interrogate the node (or
+  associated OS driver) to determine the location of the registers,
+  and access the registers directly.
+
+maintainers:
+  - Lee Jones <lee.jones@linaro.org>
+
+select:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - syscon
+
+  required:
+    - compatible
+
+properties:
+  compatible:
+    anyOf:
+      - items:
+          - enum:
+              - allwinner,sun8i-a83t-system-controller
+              - allwinner,sun8i-h3-system-controller
+              - allwinner,sun8i-v3s-system-controller
+              - allwinner,sun50i-a64-system-controller
+              - hisilicon,dsa-subctrl
+              - hisilicon,hi6220-sramctrl
+              - hisilicon,pcie-sas-subctrl
+              - hisilicon,peri-subctrl
+              - microchip,sparx5-cpu-syscon
+              - mstar,msc313-pmsleep
+              - samsung,exynos3-sysreg
+              - samsung,exynos4-sysreg
+              - samsung,exynos5-sysreg
+              - samsung,exynos5433-sysreg
+
+          - const: syscon
+
+      - contains:
+          const: syscon
+        minItems: 2
+        maxItems: 4  # Should be enough
+
+  reg:
+    maxItems: 1
+
+  reg-io-width:
+    description: |
+      The size (in bytes) of the IO accesses that should be performed
+      on the device.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [1, 2, 4, 8]
+
+  hwlocks:
+    maxItems: 1
+    description:
+      Reference to a phandle of a hardware spinlock provider node.
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: true
+
+examples:
+  - |
+    syscon: syscon@1c00000 {
+        compatible = "allwinner,sun8i-h3-system-controller", "syscon";
+        reg = <0x01c00000 0x1000>;
+    };
+
+  - |
+    gpr: iomuxc-gpr@20e0000 {
+        compatible = "fsl,imx6q-iomuxc-gpr", "syscon";
+        reg = <0x020e0000 0x38>;
+        hwlocks = <&hwlock1 1>;
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mfd/tc3589x.txt b/Documentation/devicetree/bindings/mfd/tc3589x.txt
new file mode 100644
index 000000000..4f22b2b07
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/tc3589x.txt
@@ -0,0 +1,107 @@
+* Toshiba TC3589x multi-purpose expander
+
+The Toshiba TC3589x series are I2C-based MFD devices which may expose the
+following built-in devices: gpio, keypad, rotator (vibrator), PWM (for
+e.g. LEDs or vibrators) The included models are:
+
+- TC35890
+- TC35892
+- TC35893
+- TC35894
+- TC35895
+- TC35896
+
+Required properties:
+ - compatible : must be "toshiba,tc35890", "toshiba,tc35892", "toshiba,tc35893",
+   "toshiba,tc35894", "toshiba,tc35895" or "toshiba,tc35896"
+ - reg : I2C address of the device
+ - interrupts : the interrupt on the parent the controller is connected to
+ - interrupt-controller : marks the device node as an interrupt controller
+ - #interrupt-cells : should be <1>, the first cell is the IRQ offset on this
+   TC3589x interrupt controller.
+
+Optional nodes:
+
+- GPIO
+  This GPIO module inside the TC3589x has 24 (TC35890, TC35892) or 20
+  (other models) GPIO lines.
+ - compatible : must be "toshiba,tc3589x-gpio"
+ - interrupts : interrupt on the parent, which must be the tc3589x MFD device
+ - interrupt-controller : marks the device node as an interrupt controller
+ - #interrupt-cells : should be <2>, the first cell is the IRQ offset on this
+   TC3589x GPIO interrupt controller, the second cell is the interrupt flags
+   in accordance with <dt-bindings/interrupt-controller/irq.h>. The following
+   flags are valid:
+   - IRQ_TYPE_LEVEL_LOW
+   - IRQ_TYPE_LEVEL_HIGH
+   - IRQ_TYPE_EDGE_RISING
+   - IRQ_TYPE_EDGE_FALLING
+   - IRQ_TYPE_EDGE_BOTH
+ - gpio-controller : marks the device node as a GPIO controller
+ - #gpio-cells : should be <2>, the first cell is the GPIO offset on this
+   GPIO controller, the second cell is the flags.
+
+- Keypad
+  This keypad is the same on all variants, supporting up to 96 different
+  keys. The linux-specific properties are modeled on those already existing
+  in other input drivers.
+ - compatible : must be "toshiba,tc3589x-keypad"
+ - debounce-delay-ms : debounce interval in milliseconds
+ - keypad,num-rows : number of rows in the matrix, see
+   bindings/input/matrix-keymap.txt
+ - keypad,num-columns : number of columns in the matrix, see
+   bindings/input/matrix-keymap.txt
+ - linux,keymap: the definition can be found in
+   bindings/input/matrix-keymap.txt
+ - linux,no-autorepeat: do no enable autorepeat feature.
+ - wakeup-source: use any event on keypad as wakeup event.
+		  (Legacy property supported: "linux,wakeup")
+
+Example:
+
+tc35893@44 {
+	compatible = "toshiba,tc35893";
+	reg = <0x44>;
+	interrupt-parent = <&gpio6>;
+	interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+
+	interrupt-controller;
+	#interrupt-cells = <1>;
+
+	tc3589x_gpio {
+		compatible = "toshiba,tc3589x-gpio";
+		interrupts = <0>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+	tc3589x_keypad {
+		compatible = "toshiba,tc3589x-keypad";
+		interrupts = <6>;
+		debounce-delay-ms = <4>;
+		keypad,num-columns = <8>;
+		keypad,num-rows = <8>;
+		linux,no-autorepeat;
+		linux,keymap = <0x0301006b
+				0x04010066
+				0x06040072
+				0x040200d7
+				0x0303006a
+				0x0205000e
+				0x0607008b
+				0x0500001c
+				0x0403000b
+				0x03040034
+				0x05020067
+				0x0305006c
+				0x040500e7
+				0x0005009e
+				0x06020073
+				0x01030039
+				0x07060069
+				0x050500d9>;
+		wakeup-source;
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml b/Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml
new file mode 100644
index 000000000..19fcf59fd
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml
@@ -0,0 +1,76 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com/
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/ti,j721e-system-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI J721e System Controller Registers R/W Device Tree Bindings
+
+description: |
+  This represents the Control Module registers (CTRL_MMR0) on the SoC.
+  System controller node represents a register region containing a set
+  of miscellaneous registers. The registers are not cohesive enough to
+  represent as any specific type of device. The typical use-case is
+  for some other node's driver, or platform-specific code, to acquire
+  a reference to the syscon node (e.g. by phandle, node path, or
+  search using a specific compatible value), interrogate the node (or
+  associated OS driver) to determine the location of the registers,
+  and access the registers directly.
+
+maintainers:
+  - Kishon Vijay Abraham I <kishon@ti.com>
+  - Roger Quadros <rogerq@ti.com
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - ti,j721e-system-controller
+      - const: syscon
+      - const: simple-mfd
+
+  reg:
+    maxItems: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 1
+
+  ranges: true
+
+patternProperties:
+  # Optional children
+  "^serdes-ln-ctrl@[0-9a-f]+$":
+    type: object
+    description: |
+      This is the SERDES lane control mux. It should follow the bindings
+      specified in
+      Documentation/devicetree/bindings/mux/reg-mux.txt
+
+required:
+  - compatible
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+  - ranges
+
+additionalProperties: false
+
+examples:
+  - |
+    scm_conf: scm-conf@100000 {
+        compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+        reg = <0x00100000 0x1c000>;
+        #address-cells = <1>;
+        #size-cells = <1>;
+        ranges;
+
+        serdes_ln_ctrl: serdes-ln-ctrl@4080 {
+            compatible = "mmio-mux";
+            reg = <0x00004080 0x50>;
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/mfd/ti,lp87524-q1.yaml b/Documentation/devicetree/bindings/mfd/ti,lp87524-q1.yaml
new file mode 100644
index 000000000..c4fc5345d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/ti,lp87524-q1.yaml
@@ -0,0 +1,112 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/ti,lp87524-q1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI LP87524-Q1 four 1-phase output buck converter
+
+maintainers:
+  - Keerthy <j-keerthy@ti.com>
+
+properties:
+  compatible:
+    const: ti,lp87524-q1
+
+  reg:
+    description: I2C slave address
+    const: 0x60
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    description:
+      The first cell is the pin number.
+      The second cell is is used to specify flags.
+      See ../gpio/gpio.txt for more information.
+    const: 2
+
+  regulators:
+    type: object
+
+    patternProperties:
+      "^buck[0123]$":
+        type: object
+        $ref: /schemas/regulator/regulator.yaml#
+
+    required:
+      - buck0
+      - buck1
+      - buck2
+      - buck3
+
+    additionalProperties: false
+
+patternProperties:
+  "^buck[0123]-in-supply$":
+    description: Voltage regulator supply for each BUCK converter
+
+required:
+  - compatible
+  - reg
+  - gpio-controller
+  - '#gpio-cells'
+  - buck0-in-supply
+  - buck1-in-supply
+  - buck2-in-supply
+  - buck3-in-supply
+  - regulators
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c@0 {
+        reg = <0x0 0x100>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pmic@60 {
+            compatible = "ti,lp87524-q1";
+            reg = <0x60>;
+            gpio-controller;
+            #gpio-cells = <2>;
+
+            buck0-in-supply = <&vdd_5v0>;
+            buck1-in-supply = <&vdd_5v0>;
+            buck2-in-supply = <&vdd_5v0>;
+            buck3-in-supply = <&vdd_5v0>;
+
+            regulators {
+                buck0_reg: buck0 {
+                    regulator-name = "buck0";
+                    regulator-min-microvolt = <3300000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-always-on;
+                };
+
+                buck1_reg: buck1 {
+                    regulator-name = "buck1";
+                    regulator-min-microvolt = <1350000>;
+                    regulator-max-microvolt = <1350000>;
+                    regulator-always-on;
+                };
+
+                buck2_reg: buck2 {
+                    regulator-name = "buck2";
+                    regulator-min-microvolt = <950000>;
+                    regulator-max-microvolt = <950000>;
+                    regulator-always-on;
+                };
+
+                buck3_reg: buck3 {
+                    regulator-name = "buck3";
+                    regulator-min-microvolt = <1800000>;
+                    regulator-max-microvolt = <1800000>;
+                    regulator-always-on;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mfd/ti,lp87561-q1.yaml b/Documentation/devicetree/bindings/mfd/ti,lp87561-q1.yaml
new file mode 100644
index 000000000..a7e57c091
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/ti,lp87561-q1.yaml
@@ -0,0 +1,83 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/ti,lp87561-q1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI LP87561-Q1 single 4-phase output buck converter
+
+maintainers:
+  - Keerthy <j-keerthy@ti.com>
+
+properties:
+  compatible:
+    const: ti,lp87561-q1
+
+  reg:
+    description: I2C slave address
+    const: 0x60
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    description:
+      The first cell is the pin number.
+      The second cell is is used to specify flags.
+      See ../gpio/gpio.txt for more information.
+    const: 2
+
+  buck3210-in-supply:
+    description:
+      Voltage regulator supply for all the four BUCK converters.
+
+  regulators:
+    type: object
+
+    properties:
+      buck3210:
+        type: object
+        $ref: /schemas/regulator/regulator.yaml#
+
+    required:
+      - buck3210
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - gpio-controller
+  - '#gpio-cells'
+  - buck3210-in-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c@0 {
+        reg = <0x0 0x100>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pmic@60 {
+            compatible = "ti,lp87561-q1";
+            reg = <0x60>;
+            gpio-controller;
+            #gpio-cells = <2>;
+
+            buck3210-in-supply = <&vsys_3v3>;
+
+            regulators {
+                buck3210_reg: buck3210 {
+                    /* VDD_CORE */
+                    regulator-name = "buck3210";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <800000>;
+                    regulator-always-on;
+                    regulator-boot-on;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mfd/ti,lp87565-q1.yaml b/Documentation/devicetree/bindings/mfd/ti,lp87565-q1.yaml
new file mode 100644
index 000000000..1da6d6a95
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/ti,lp87565-q1.yaml
@@ -0,0 +1,101 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/ti,lp87565-q1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI LP87565-Q1 / LP87565 dual 2-phase output buck converter
+
+maintainers:
+  - Keerthy <j-keerthy@ti.com>
+
+properties:
+  compatible:
+    oneOf:
+      - const: ti,lp87565
+      - const: ti,lp87565-q1
+
+  reg:
+    description: I2C slave address
+    const: 0x60
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    description:
+      The first cell is the pin number.
+      The second cell is is used to specify flags.
+      See ../gpio/gpio.txt for more information.
+    const: 2
+
+  buck10-in-supply:
+    description:
+      Voltage regulator supply for BUCK0 and BUCK1 converters.
+
+  buck23-in-supply:
+    description:
+      Voltage regulator supply for BUCK2 and BUCK3 converters.
+
+  regulators:
+    type: object
+
+    patternProperties:
+      "^buck(10|23)$":
+        type: object
+        $ref: /schemas/regulator/regulator.yaml#
+
+    required:
+      - buck10
+      - buck23
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - gpio-controller
+  - '#gpio-cells'
+  - buck10-in-supply
+  - buck23-in-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c@0 {
+        reg = <0x0 0x100>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pmic@60 {
+            compatible = "ti,lp87565-q1";
+            reg = <0x60>;
+            gpio-controller;
+            #gpio-cells = <2>;
+
+            buck10-in-supply = <&vsys_3v3>;
+            buck23-in-supply = <&vsys_3v3>;
+
+            regulators {
+                buck10_reg: buck10 {
+                    /* VDD_MPU */
+                    regulator-name = "buck10";
+                    regulator-min-microvolt = <850000>;
+                    regulator-max-microvolt = <1250000>;
+                    regulator-always-on;
+                    regulator-boot-on;
+                };
+
+                buck23_reg: buck23 {
+                    /* VDD_GPU */
+                    regulator-name = "buck23";
+                    regulator-min-microvolt = <850000>;
+                    regulator-max-microvolt = <1250000>;
+                    regulator-boot-on;
+                    regulator-always-on;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mfd/ti-keystone-devctrl.txt b/Documentation/devicetree/bindings/mfd/ti-keystone-devctrl.txt
new file mode 100644
index 000000000..71a1f5963
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/ti-keystone-devctrl.txt
@@ -0,0 +1,19 @@
+* Device tree bindings for Texas Instruments keystone device state control
+
+The Keystone II devices have a set of registers that are used to control
+the status of its peripherals. This node is intended to allow access to
+this functionality.
+
+Required properties:
+
+- compatible:		"ti,keystone-devctrl", "syscon"
+
+- reg:			contains offset/length value for device state control
+			registers space.
+
+Example:
+
+devctrl: device-state-control@02620000 {
+	compatible = "ti,keystone-devctrl", "syscon";
+	reg = <0x02620000 0x1000>;
+};
diff --git a/Documentation/devicetree/bindings/mfd/ti-lmu.txt b/Documentation/devicetree/bindings/mfd/ti-lmu.txt
new file mode 100644
index 000000000..2296b8f24
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/ti-lmu.txt
@@ -0,0 +1,269 @@
+TI LMU (Lighting Management Unit) device tree bindings
+
+TI LMU driver supports lighting devices below.
+
+   Name                  Child nodes
+  ------      ---------------------------------
+  LM3631       Backlight and regulator
+  LM3632       Backlight and regulator
+  LM3633       Backlight, LED and fault monitor
+  LM3695       Backlight
+  LM36274      Backlight and regulator
+
+Required properties:
+  - compatible: Should be one of:
+                "ti,lm3631"
+                "ti,lm3632"
+                "ti,lm3633"
+                "ti,lm3695"
+		"ti,lm36274"
+  - reg: I2C slave address.
+         0x11 for LM3632
+         0x29 for LM3631
+         0x36 for LM3633
+         0x63 for LM3695
+         0x11 for LM36274
+
+Optional properties:
+  - enable-gpios: A GPIO specifier for hardware enable pin.
+  - ramp-up-us: Current ramping from one brightness level to
+		the a higher brightness level.
+		Range from 2048 us - 117.44 s
+  - ramp-down-us: Current ramping from one brightness level to
+		  the a lower brightness level.
+		  Range from 2048 us - 117.44 s
+  - ti,brightness-resolution - This determines whether to use 8 bit brightness
+			       mode or 11 bit brightness mode.  If this value is
+			       not set the device is defaulted to the preferred
+			       8bit brightness mode per 7.3.4.1 of the data
+			       sheet.  This setting can either be in the parent
+			       node or as part of the LED child nodes.  This
+			       is determined by the part itself if the strings
+			       have a common brightness register or individual
+			       brightness registers.
+			       The values are 255 (8bit) or 2047 (11bit).
+
+Required node:
+  - backlight: All LMU devices have backlight child nodes.
+               For the properties, please refer to [1].
+
+Optional nodes:
+  - fault-monitor: Hardware fault monitoring driver for LM3633 and LM3697.
+    Required properties:
+      - compatible: Should be one of:
+                    "ti,lm3633-fault-monitor"
+  - leds: LED properties for LM3633. Please refer to [2].
+	  LED properties for LM36274. Please refer to [4].
+  - regulators: Regulator properties for LM3631 and LM3632.
+                Please refer to [3].
+
+[1] ../leds/backlight/ti-lmu-backlight.txt
+[2] ../leds/leds-lm3633.txt
+[3] ../regulator/lm363x-regulator.txt
+[4] ../leds/leds-lm36274.txt
+
+lm3631@29 {
+	compatible = "ti,lm3631";
+	reg = <0x29>;
+
+	regulators {
+		compatible = "ti,lm363x-regulator";
+
+		vboost {
+			regulator-name = "lcd_boost";
+			regulator-min-microvolt = <4500000>;
+			regulator-max-microvolt = <6350000>;
+			regulator-always-on;
+		};
+
+		vcont {
+			regulator-name = "lcd_vcont";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		voref {
+			regulator-name = "lcd_voref";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6000000>;
+		};
+
+		vpos {
+			regulator-name = "lcd_vpos";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6000000>;
+			regulator-boot-on;
+		};
+
+		vneg {
+			regulator-name = "lcd_vneg";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6000000>;
+			regulator-boot-on;
+		};
+	};
+
+	backlight {
+		compatible = "ti,lm3631-backlight";
+
+		lcd_bl {
+			led-sources = <0 1>;
+			ramp-up-us = <300000>;
+		};
+	};
+};
+
+lm3632@11 {
+	compatible = "ti,lm3632";
+	reg = <0x11>;
+
+	enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; /* PC2 */
+
+	regulators {
+		compatible = "ti,lm363x-regulator";
+
+		enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>,
+			       <&pioC 1 GPIO_ACTIVE_HIGH>;
+
+		vboost {
+			regulator-name = "lcd_boost";
+			regulator-min-microvolt = <4500000>;
+			regulator-max-microvolt = <6400000>;
+			regulator-always-on;
+		};
+
+		vpos {
+			regulator-name = "lcd_vpos";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6000000>;
+		};
+
+		vneg {
+			regulator-name = "lcd_vneg";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6000000>;
+		};
+	};
+
+	backlight {
+		compatible = "ti,lm3632-backlight";
+
+		pwms = <&pwm0 0 10000 0>; /* pwm number, period, polarity */
+		pwm-names = "lmu-backlight";
+
+		lcd {
+			led-sources = <0 1>;
+			pwm-period = <10000>;
+		};
+	};
+};
+
+lm3633@36 {
+	compatible = "ti,lm3633";
+	reg = <0x36>;
+
+	enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
+
+	backlight {
+		compatible = "ti,lm3633-backlight";
+
+		main {
+			label = "main_lcd";
+			led-sources = <1 2>;
+			ramp-up-us = <500000>;
+			ramp-down-us = <500000>;
+		};
+
+		front {
+			label = "front_lcd";
+			led-sources = <0>;
+			ramp-up-us = <1000000>;
+			ramp-down-us = <0>;
+		};
+	};
+
+	leds {
+		compatible = "ti,lm3633-leds";
+
+		chan1 {
+			label = "status";
+			led-sources = <1>;
+			led-max-microamp = <6000>;
+		};
+
+		chan345 {
+			label = "rgb";
+			led-sources = <3 4 5>;
+			led-max-microamp = <10000>;
+		};
+	};
+
+	fault-monitor {
+		compatible = "ti,lm3633-fault-monitor";
+	};
+};
+
+lm3695@63 {
+	compatible = "ti,lm3695";
+	reg = <0x63>;
+
+	enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
+
+	backlight {
+		compatible = "ti,lm3695-backlight";
+
+		lcd {
+			label = "bl";
+			led-sources = <0 1>;
+		};
+	};
+};
+
+lm36274@11 {
+	compatible = "ti,lm36274";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0x11>;
+
+	enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
+	regulators {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "ti,lm363x-regulator";
+
+		enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>,
+			       <&pioC 1 GPIO_ACTIVE_HIGH>;
+
+		vboost {
+			regulator-name = "lcd_boost";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <7150000>;
+			regulator-always-on;
+		};
+
+		vpos {
+			regulator-name = "lcd_vpos";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6500000>;
+		};
+
+		vneg {
+			regulator-name = "lcd_vneg";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6500000>;
+		};
+	};
+
+	backlight {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "ti,lm36274-backlight";
+
+		led@0 {
+			reg = <0>;
+			led-sources = <0 2>;
+			label = "white:backlight_cluster";
+			linux,default-trigger = "backlight";
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/tps6105x.txt b/Documentation/devicetree/bindings/mfd/tps6105x.txt
new file mode 100644
index 000000000..dc448a9d5
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/tps6105x.txt
@@ -0,0 +1,62 @@
+* Device tree bindings for TI TPS61050/61052 Boost Converters
+
+The TP61050/TPS61052 is a high-power "white LED driver". The
+device provides LED, GPIO and regulator functionalities.
+
+Required properties:
+- compatible:		"ti,tps61050" or "ti,tps61052"
+- reg:			Specifies the I2C slave address
+
+Optional sub-node:
+
+This subnode selects the chip's operational mode.
+There can be at most one single available subnode.
+
+- regulator: presence of this sub-node puts the chip in regulator mode.
+	see ../regulator/regulator.yaml
+
+- led: presence of this sub-node puts the chip in led mode.
+	Optional properties:
+	- function : see ../leds/common.txt
+	- color    : see ../leds/common.txt
+	- label    : see ../leds/common.txt
+			(deprecated)
+
+Example (GPIO operation only):
+
+i2c0 {
+	tps61052@33 {
+		compatible = "ti,tps61052";
+		reg = <0x33>;
+	};
+};
+
+Example (GPIO + regulator operation):
+
+i2c0 {
+	tps61052@33 {
+		compatible = "ti,tps61052";
+		reg = <0x33>;
+
+		regulator {
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			regulator-always-on;
+		};
+	};
+};
+
+Example (GPIO + led operation):
+
+#include <dt-bindings/leds/common.h>
+
+i2c0 {
+	tps61052@33 {
+		compatible = "ti,tps61052";
+		reg = <0x33>;
+
+		led {
+			color = <LED_COLOR_ID_WHITE>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/tps6507x.txt b/Documentation/devicetree/bindings/mfd/tps6507x.txt
new file mode 100644
index 000000000..8fffa3c5e
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/tps6507x.txt
@@ -0,0 +1,91 @@
+TPS6507x Power Management Integrated Circuit
+
+Required properties:
+- compatible: "ti,tps6507x"
+- reg: I2C slave address
+- regulators: This is the list of child nodes that specify the regulator
+  initialization data for defined regulators. Not all regulators for the
+  given device need to be present. The definition for each of these nodes
+  is defined using the standard binding for regulators found at
+  Documentation/devicetree/bindings/regulator/regulator.txt.
+  The regulator is matched with the regulator-compatible.
+
+  The valid regulator-compatible values are:
+  tps6507x: vdcdc1, vdcdc2, vdcdc3, vldo1, vldo2
+- xxx-supply: Input voltage supply regulator.
+  These entries are required if regulators are enabled for a device.
+  Missing of these properties can cause the regulator registration
+  fails.
+  If some of input supply is powered through battery or always-on
+  supply then also it is require to have these parameters with proper
+  node handle of always on power supply.
+  tps6507x:
+       vindcdc1_2-supply: VDCDC1 and VDCDC2 input.
+       vindcdc3-supply  : VDCDC3 input.
+       vldo1_2-supply   : VLDO1 and VLDO2 input.
+
+Regulator Optional properties:
+- defdcdc_default: It's property of DCDC2 and DCDC3 regulators.
+			0: If defdcdc pin of DCDC2/DCDC3 is pulled to GND.
+			1: If defdcdc pin of DCDC2/DCDC3 is driven HIGH.
+  If this property is not defined, it defaults to 0 (not enabled).
+
+Example:
+
+	pmu: tps6507x@48 {
+		compatible = "ti,tps6507x";
+		reg = <0x48>;
+
+		vindcdc1_2-supply = <&vbat>;
+		vindcdc3-supply = <...>;
+		vinldo1_2-supply = <...>;
+
+		regulators {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			vdcdc1_reg: regulator@0 {
+				regulator-compatible = "VDCDC1";
+				reg = <0>;
+				regulator-min-microvolt = <3150000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+			vdcdc2_reg: regulator@1 {
+				regulator-compatible = "VDCDC2";
+				reg = <1>;
+				regulator-min-microvolt = <1710000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-always-on;
+				regulator-boot-on;
+				defdcdc_default = <1>;
+			};
+			vdcdc3_reg: regulator@2 {
+				regulator-compatible = "VDCDC3";
+				reg = <2>;
+				regulator-min-microvolt = <950000>
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+				defdcdc_default = <1>;
+			};
+			ldo1_reg: regulator@3 {
+				regulator-compatible = "LDO1";
+				reg = <3>;
+				regulator-min-microvolt = <1710000>;
+				regulator-max-microvolt = <1890000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+			ldo2_reg: regulator@4 {
+				regulator-compatible = "LDO2";
+				reg = <4>;
+				regulator-min-microvolt = <1140000>;
+				regulator-max-microvolt = <1320000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+
+	};
diff --git a/Documentation/devicetree/bindings/mfd/tps65086.txt b/Documentation/devicetree/bindings/mfd/tps65086.txt
new file mode 100644
index 000000000..67eac0ed3
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/tps65086.txt
@@ -0,0 +1,54 @@
+* TPS65086 Power Management Integrated Circuit (PMIC) bindings
+
+Required properties:
+ - compatible		: Should be "ti,tps65086".
+ - reg			: I2C slave address.
+ - interrupts		: The interrupt line the device is connected to.
+ - interrupt-controller	: Marks the device node as an interrupt controller.
+ - #interrupt-cells	: The number of cells to describe an IRQ, should be 2.
+			    The first cell is the IRQ number.
+			    The second cell is the flags, encoded as trigger
+			    masks from ../interrupt-controller/interrupts.txt.
+ - gpio-controller      : Marks the device node as a GPIO Controller.
+ - #gpio-cells          : Should be two.  The first cell is the pin number and
+                            the second cell is used to specify flags.
+                            See ../gpio/gpio.txt for more information.
+ - regulators:          : List of child nodes that specify the regulator
+                            initialization data. Child nodes must be named
+                            after their hardware counterparts: buck[1-6],
+                            ldoa[1-3], swa1, swb[1-2], and vtt. Each child
+                            node is defined using the standard binding for
+                            regulators and the optional regulator properties
+                            defined below.
+
+Optional regulator properties:
+ - ti,regulator-step-size-25mv	: This is applicable for buck[1-6], set this
+				    if the regulator is factory set with a 25mv
+				    step voltage mapping.
+ - ti,regulator-decay		: This is applicable for buck[1-6], set this if
+				    the output needs to decay, default is for
+				    the output to slew down.
+
+Example:
+
+	pmic: tps65086@5e {
+		compatible = "ti,tps65086";
+		reg = <0x5e>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		regulators {
+			buck1 {
+				regulator-name = "vcc1";
+				regulator-min-microvolt = <1600000>;
+				regulator-max-microvolt = <1600000>;
+				regulator-boot-on;
+				ti,regulator-decay;
+				ti,regulator-step-size-25mv;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt
new file mode 100644
index 000000000..a5ced46bb
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/tps65910.txt
@@ -0,0 +1,205 @@
+TPS65910 Power Management Integrated Circuit
+
+Required properties:
+- compatible: "ti,tps65910" or "ti,tps65911"
+- reg: I2C slave address
+- interrupts: the interrupt outputs of the controller
+- #gpio-cells: number of cells to describe a GPIO, this should be 2.
+  The first cell is the GPIO number.
+  The second cell is used to specify additional options <unused>.
+- gpio-controller: mark the device as a GPIO controller
+- #interrupt-cells: the number of cells to describe an IRQ, this should be 2.
+  The first cell is the IRQ number.
+  The second cell is the flags, encoded as the trigger masks from
+  Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+- regulators: This is the list of child nodes that specify the regulator
+  initialization data for defined regulators. Not all regulators for the given
+  device need to be present. The definition for each of these nodes is defined
+  using the standard binding for regulators found at
+  Documentation/devicetree/bindings/regulator/regulator.txt.
+  The regulator is matched with the regulator-compatible.
+
+  The valid regulator-compatible values are:
+  tps65910: vrtc, vio, vdd1, vdd2, vdd3, vdig1, vdig2, vpll, vdac, vaux1,
+            vaux2, vaux33, vmmc, vbb
+  tps65911: vrtc, vio, vdd1, vdd2, vddctrl, ldo1, ldo2, ldo3, ldo4, ldo5,
+            ldo6, ldo7, ldo8
+
+- xxx-supply: Input voltage supply regulator.
+  These entries are required if regulators are enabled for a device. Missing these
+  properties can cause the regulator registration to fail.
+  If some of input supply is powered through battery or always-on supply then
+  also it is require to have these parameters with proper node handle of always
+  on power supply.
+  tps65910:
+	vcc1-supply: VDD1 input.
+	vcc2-supply: VDD2 input.
+	vcc3-supply: VAUX33 and VMMC input.
+	vcc4-supply: VAUX1 and VAUX2 input.
+	vcc5-supply: VPLL and VDAC input.
+	vcc6-supply: VDIG1 and VDIG2 input.
+	vcc7-supply: VRTC and VBB input.
+	vccio-supply: VIO input.
+  tps65911:
+	vcc1-supply: VDD1 input.
+	vcc2-supply: VDD2 input.
+	vcc3-supply: LDO6, LDO7 and LDO8 input.
+	vcc4-supply: LDO5 input.
+	vcc5-supply: LDO3 and LDO4 input.
+	vcc6-supply: LDO1 and LDO2 input.
+	vcc7-supply: VRTC input.
+	vccio-supply: VIO input.
+
+Optional properties:
+- ti,vmbch-threshold: (tps65911) main battery charged threshold
+  comparator. (see VMBCH_VSEL in TPS65910 datasheet)
+- ti,vmbch2-threshold: (tps65911) main battery discharged threshold
+  comparator. (see VMBCH_VSEL in TPS65910 datasheet)
+- ti,en-ck32k-xtal: enable external 32-kHz crystal oscillator (see CK32K_CTRL
+  in TPS6591X datasheet)
+- ti,en-gpio-sleep: enable sleep control for gpios
+  There should be 9 entries here, one for each gpio.
+- ti,system-power-controller: Telling whether or not this pmic is controlling
+  the system power.
+- ti,sleep-enable: Enable SLEEP state.
+- ti,sleep-keep-therm: Keep thermal monitoring on in sleep state.
+- ti,sleep-keep-ck32k: Keep the 32KHz clock output on in sleep state.
+- ti,sleep-keep-hsclk: Keep high speed internal clock on in sleep state.
+
+Regulator Optional properties:
+- ti,regulator-ext-sleep-control: enable external sleep
+  control through external inputs [0 (not enabled), 1 (EN1), 2 (EN2) or 4(EN3)]
+  If this property is not defined, it defaults to 0 (not enabled).
+
+Example:
+
+	pmu: tps65910@d2 {
+		compatible = "ti,tps65910";
+		reg = <0xd2>;
+		interrupt-parent = <&intc>;
+		interrupts = < 0 118 0x04 >;
+
+		#gpio-cells = <2>;
+		gpio-controller;
+
+		#interrupt-cells = <2>;
+		interrupt-controller;
+
+		ti,system-power-controller;
+
+		ti,vmbch-threshold = 0;
+		ti,vmbch2-threshold = 0;
+		ti,en-ck32k-xtal;
+		ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>;
+
+		vcc1-supply = <&reg_parent>;
+		vcc2-supply = <&some_reg>;
+		vcc3-supply = <...>;
+		vcc4-supply = <...>;
+		vcc5-supply = <...>;
+		vcc6-supply = <...>;
+		vcc7-supply = <...>;
+		vccio-supply = <...>;
+
+		regulators {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			vdd1_reg: regulator@0 {
+				regulator-compatible = "vdd1";
+				reg = <0>;
+				regulator-min-microvolt = < 600000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+				ti,regulator-ext-sleep-control = <0>;
+			};
+			vdd2_reg: regulator@1 {
+				regulator-compatible = "vdd2";
+				reg = <1>;
+				regulator-min-microvolt = < 600000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+				ti,regulator-ext-sleep-control = <4>;
+			};
+			vddctrl_reg: regulator@2 {
+				regulator-compatible = "vddctrl";
+				reg = <2>;
+				regulator-min-microvolt = < 600000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				regulator-boot-on;
+				ti,regulator-ext-sleep-control = <0>;
+			};
+			vio_reg: regulator@3 {
+				regulator-compatible = "vio";
+				reg = <3>;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				ti,regulator-ext-sleep-control = <1>;
+			};
+			ldo1_reg: regulator@4 {
+				regulator-compatible = "ldo1";
+				reg = <4>;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3300000>;
+				ti,regulator-ext-sleep-control = <0>;
+			};
+			ldo2_reg: regulator@5 {
+				regulator-compatible = "ldo2";
+				reg = <5>;
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1050000>;
+				ti,regulator-ext-sleep-control = <0>;
+			};
+			ldo3_reg: regulator@6 {
+				regulator-compatible = "ldo3";
+				reg = <6>;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3300000>;
+				ti,regulator-ext-sleep-control = <0>;
+			};
+			ldo4_reg: regulator@7 {
+				regulator-compatible = "ldo4";
+				reg = <7>;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				ti,regulator-ext-sleep-control = <0>;
+			};
+			ldo5_reg: regulator@8 {
+				regulator-compatible = "ldo5";
+				reg = <8>;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3300000>;
+				ti,regulator-ext-sleep-control = <0>;
+			};
+			ldo6_reg: regulator@9 {
+				regulator-compatible = "ldo6";
+				reg = <9>;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				ti,regulator-ext-sleep-control = <0>;
+			};
+			ldo7_reg: regulator@10 {
+				regulator-compatible = "ldo7";
+				reg = <10>;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+				ti,regulator-ext-sleep-control = <1>;
+			};
+			ldo8_reg: regulator@11 {
+				regulator-compatible = "ldo8";
+				reg = <11>;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				ti,regulator-ext-sleep-control = <1>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/tps65912.txt b/Documentation/devicetree/bindings/mfd/tps65912.txt
new file mode 100644
index 000000000..8becb183a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/tps65912.txt
@@ -0,0 +1,49 @@
+* TPS65912 Power Management Integrated Circuit bindings
+
+Required properties:
+ - compatible		: Should be "ti,tps65912".
+ - reg			: Slave address or chip select number (I2C / SPI).
+ - interrupts		: The interrupt line the device is connected to.
+ - interrupt-controller	: Marks the device node as an interrupt controller.
+ - #interrupt-cells	: The number of cells to describe an IRQ, should be 2.
+			    The first cell is the IRQ number.
+			    The second cell is the flags, encoded as trigger
+			    masks from ../interrupt-controller/interrupts.txt.
+ - gpio-controller	: Marks the device node as a GPIO Controller.
+ - #gpio-cells		: Should be two.  The first cell is the pin number and
+			    the second cell is used to specify flags.
+			    See ../gpio/gpio.txt for more information.
+ - regulators:		: List of child nodes that specify the regulator
+			    initialization data. Child nodes must be named
+			    after their hardware counterparts: dcdc[1-4] and
+			    ldo[1-10]. Each child nodes is defined using the
+			    standard binding for regulators.
+
+Example:
+
+	pmic: tps65912@2d {
+		compatible = "ti,tps65912";
+		reg = <0x2d>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		regulators {
+			dcdc1 {
+				regulator-name = "vdd_core";
+				regulator-min-microvolt = <912000>;
+				regulator-max-microvolt = <1144000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <1900000>;
+				regulator-max-microvolt = <1900000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/twl-family.txt b/Documentation/devicetree/bindings/mfd/twl-family.txt
new file mode 100644
index 000000000..c2f930296
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/twl-family.txt
@@ -0,0 +1,46 @@
+Texas Instruments TWL family
+
+The TWLs are Integrated Power Management Chips.
+Some version might contain much more analog function like
+USB transceiver or Audio amplifier.
+These chips are connected to an i2c bus.
+
+
+Required properties:
+- compatible : Must be "ti,twl4030";
+  For Integrated power-management/audio CODEC device used in OMAP3
+  based boards
+- compatible : Must be "ti,twl6030";
+  For Integrated power-management used in OMAP4 based boards
+- interrupts : This i2c device has an IRQ line connected to the main SoC
+- interrupt-controller : Since the twl support several interrupts internally,
+  it is considered as an interrupt controller cascaded to the SoC one.
+- #interrupt-cells = <1>;
+
+Optional node:
+- Child nodes contain in the twl. The twl family is made of several variants
+  that support a different number of features.
+  The children nodes will thus depend of the capability of the variant.
+
+
+Example:
+/*
+ * Integrated Power Management Chip
+ * https://www.ti.com/lit/ds/symlink/twl6030.pdf
+ */
+twl@48 {
+    compatible = "ti,twl6030";
+    reg = <0x48>;
+    interrupts = <39>; /* IRQ_SYS_1N cascaded to gic */
+    interrupt-controller;
+    #interrupt-cells = <1>;
+    interrupt-parent = <&gic>;
+    #address-cells = <1>;
+    #size-cells = <0>;
+
+    twl_rtc {
+        compatible = "ti,twl_rtc";
+        interrupts = <11>;
+        reg = <0>;
+    };
+};
diff --git a/Documentation/devicetree/bindings/mfd/twl4030-audio.txt b/Documentation/devicetree/bindings/mfd/twl4030-audio.txt
new file mode 100644
index 000000000..414d2ae0a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/twl4030-audio.txt
@@ -0,0 +1,46 @@
+Texas Instruments TWL family (twl4030) audio module
+
+The audio module inside the TWL family consist of an audio codec and a vibra
+driver.
+
+Required properties:
+- compatible : must be "ti,twl4030-audio"
+
+Optional properties, nodes:
+
+Audio functionality:
+- codec { }: Need to be present if the audio functionality is used. Within this
+	     section the following options can be used:
+- ti,digimic_delay: Delay need after enabling the digimic to reduce artifacts
+		    from the start of the recorded sample (in ms)
+-ti,ramp_delay_value: HS ramp delay configuration to reduce pop noise
+-ti,hs_extmute: Use external mute for HS pop reduction
+-ti,hs_extmute_gpio: Use external GPIO to control the external mute
+-ti,offset_cncl_path: Offset cancellation path selection, refer to TRM for the
+		      valid values.
+
+Vibra functionality
+- ti,enable-vibra: Need to be set to <1> if the vibra functionality is used. if
+		   missing or it is 0, the vibra functionality is disabled.
+
+Example:
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+
+			ti,enable-vibra = <1>;
+
+			codec {
+				ti,ramp_delay_value = <3>;
+			};
+
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/twl4030-power.txt b/Documentation/devicetree/bindings/mfd/twl4030-power.txt
new file mode 100644
index 000000000..3d1996331
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/twl4030-power.txt
@@ -0,0 +1,48 @@
+Texas Instruments TWL family (twl4030) reset and power management module
+
+The power management module inside the TWL family provides several facilities
+to control the power resources, including power scripts. For now, the
+binding only supports the complete shutdown of the system after poweroff.
+
+Required properties:
+- compatible : must be one of the following
+	"ti,twl4030-power"
+	"ti,twl4030-power-reset"
+	"ti,twl4030-power-idle"
+	"ti,twl4030-power-idle-osc-off"
+
+The use of ti,twl4030-power-reset is recommended at least on
+3530 that needs a special configuration for warm reset to work.
+
+When using ti,twl4030-power-idle, the TI recommended configuration
+for idle modes is loaded to the tlw4030 PMIC.
+
+When using ti,twl4030-power-idle-osc-off, the TI recommended
+configuration is used with the external oscillator being shut
+down during off-idle. Note that this does not work on all boards
+depending on how the external oscillator is wired.
+
+Optional properties:
+
+- ti,system-power-controller: This indicates that TWL4030 is the
+  power supply master of the system. With this flag, the chip will
+  initiate an ACTIVE-to-OFF or SLEEP-to-OFF transition when the
+  system poweroffs.
+
+- ti,use_poweroff: Deprecated name for ti,system-power-controller
+
+Example:
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+
+		twl_power: power {
+			compatible = "ti,twl4030-power";
+			ti,use_poweroff;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/twl6040.txt b/Documentation/devicetree/bindings/mfd/twl6040.txt
new file mode 100644
index 000000000..06e9dd7a0
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/twl6040.txt
@@ -0,0 +1,67 @@
+Texas Instruments TWL6040 family
+
+The TWL6040s are 8-channel high quality low-power audio codecs providing audio,
+vibra and GPO functionality on OMAP4+ platforms.
+They are connected ot the host processor via i2c for commands, McPDM for audio
+data and commands.
+
+Required properties:
+- compatible : "ti,twl6040" for twl6040, "ti,twl6041" for twl6041
+- reg: must be 0x4b for i2c address
+- interrupts: twl6040 has one interrupt line connecteded to the main SoC
+- gpio-controller:
+- #gpio-cells = <1>: twl6040 provides GPO lines.
+- #clock-cells = <0>; twl6040 is a provider of pdmclk which is used by McPDM
+- twl6040,audpwron-gpio: Power on GPIO line for the twl6040
+
+- vio-supply: Regulator for the twl6040 VIO supply
+- v2v1-supply: Regulator for the twl6040 V2V1 supply
+
+Optional properties, nodes:
+- enable-active-high: To power on the twl6040 during boot.
+- clocks: phandle to the clk32k and/or to mclk clock provider
+- clock-names: Must be "clk32k" for the 32K clock and "mclk" for the MCLK.
+
+Vibra functionality
+Required properties:
+- vddvibl-supply: Regulator for the left vibra motor
+- vddvibr-supply: Regulator for the right vibra motor
+- vibra { }: Configuration section for vibra parameters containing the following
+	     properties:
+- ti,vibldrv-res: Resistance parameter for left driver
+- ti,vibrdrv-res: Resistance parameter for right driver
+- ti,viblmotor-res: Resistance parameter for left motor
+- ti,viblmotor-res: Resistance parameter for right motor
+
+Optional properties within vibra { } section:
+- vddvibl_uV: If the vddvibl default voltage need to be changed
+- vddvibr_uV: If the vddvibr default voltage need to be changed
+
+Example:
+&i2c1 {
+	twl6040: twl@4b {
+		compatible = "ti,twl6040";
+
+		interrupts = <0 119 4>;
+		interrupt-parent = <&gic>;
+		twl6040,audpwron-gpio = <&gpio4 31 0>;
+
+		vio-supply = <&v1v8>;
+		v2v1-supply = <&v2v1>;
+		enable-active-high;
+
+		/* regulators for vibra motor */
+		vddvibl-supply = <&vbat>;
+		vddvibr-supply = <&vbat>;
+
+		vibra {
+			/* Vibra driver, motor resistance parameters */
+			ti,vibldrv-res = <8>;
+			ti,vibrdrv-res = <3>;
+			ti,viblmotor-res = <10>;
+			ti,vibrmotor-res = <10>;
+		};
+	};
+};
+
+/include/ "twl6040.dtsi"
diff --git a/Documentation/devicetree/bindings/mfd/wlf,arizona.yaml b/Documentation/devicetree/bindings/mfd/wlf,arizona.yaml
new file mode 100644
index 000000000..9e762d474
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/wlf,arizona.yaml
@@ -0,0 +1,280 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/wlf,arizona.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic/Wolfson Microelectronics Arizona class audio SoCs
+
+maintainers:
+  - patches@opensource.cirrus.com
+
+description: |
+  These devices are audio SoCs with extensive digital capabilities and a
+  range of analogue I/O.
+
+allOf:
+  - $ref: /schemas/sound/wlf,arizona.yaml#
+  - $ref: /schemas/regulator/wlf,arizona.yaml#
+  - $ref: /schemas/extcon/wlf,arizona.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - cirrus,cs47l24
+              - wlf,wm1831
+    then:
+      required:
+        - DCVDD-supply
+        - MICVDD-supply
+    else:
+      properties:
+        LDOVDD-supply:
+          description:
+            Digital power supply, used internally to generate DCVDD when
+            internally supplied.
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - wlf,wm1814
+              - wlf,wm5102
+              - wlf,wm5110
+              - wlf,wm8280
+              - wlf,wm8997
+              - wlf,wm8998
+    then:
+      properties:
+        DBVDD2-supply:
+          description:
+            Databus power supply.
+
+      required:
+        - DBVDD2-supply
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - wlf,wm1814
+              - wlf,wm5102
+              - wlf,wm5110
+              - wlf,wm8280
+              - wlf,wm8998
+    then:
+      properties:
+        DBVDD3-supply:
+          description:
+            Databus power supply.
+
+      required:
+        - DBVDD3-supply
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - cirrus,cs47l24
+              - wlf,wm1831
+              - wlf,wm8997
+    then:
+      properties:
+        SPKVDD-supply:
+          description:
+            Mono speaker driver power supply.
+
+      required:
+        - SPKVDD-supply
+    else:
+      properties:
+        SPKVDDL-supply:
+          description:
+            Left speaker driver power supply.
+
+        SPKVDDR-supply:
+          description:
+            Right speaker driver power supply.
+
+      required:
+        - SPKVDDL-supply
+        - SPKVDDR-supply
+
+properties:
+  compatible:
+    enum:
+      - cirrus,cs47l24
+      - wlf,wm1814
+      - wlf,wm1831
+      - wlf,wm5102
+      - wlf,wm5110
+      - wlf,wm8280
+      - wlf,wm8997
+      - wlf,wm8998
+
+  reg:
+    maxItems: 1
+
+  AVDD-supply:
+    description:
+      Analogue power supply.
+
+  CPVDD-supply:
+    description:
+      Charge pump power supply.
+
+  DBVDD1-supply:
+    description:
+      Databus power supply.
+
+  DCVDD-supply:
+    description:
+      Digital power supply, normally supplied internally except on cs47l24,
+      wm1831 where it is mandatory.
+
+  MICVDD-supply:
+    description:
+      Microphone power supply, normally supplied internally except on
+      cs47l24, wm1831 where it is mandatory.
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    description:
+      The first cell is the pin number and the second cell is used to
+      specify optional parameters.
+    const: 2
+
+  wlf,gpio-defaults:
+    description:
+      A list of GPIO configuration register values. Defines for the
+      appropriate values can found in dt-bindings/mfd/arizona.h. If
+      absent, no configuration of these registers is performed. If any
+      entry has a value that is out of range for a 16 bit register then the
+      chip default will be used. If present exactly five values must be
+      specified.
+    $ref: "/schemas/types.yaml#/definitions/uint32-array"
+    minItems: 1
+    maxItems: 5
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    description:
+      The first cell is the IRQ number.  The second cell is the flags,
+      encoded as trigger masks.
+    const: 2
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    description:
+      Should reference the clocks supplied on MCLK1 and MCLK2.
+    minItems: 1
+    maxItems: 2
+
+  clock-names:
+    description:
+      Should contains two strings mclk1 for the clock supplied on MCLK1,
+      recommended to be a high quality audio reference clock mclk2 for the
+      clock supplied on MCLK2, recommended to be an always on 32k clock.
+    oneOf:
+      - items:
+          - const: mclk1
+      - items:
+          - const: mclk2
+      - items:
+          - const: mclk1
+          - const: mclk2
+
+  reset-gpios:
+    maxItems: 1
+
+  wlf,reset:
+    description:
+      GPIO specifier for the GPIO controlling RESET
+    deprecated: true
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    maxItems: 1
+
+required:
+  - compatible
+  - AVDD-supply
+  - CPVDD-supply
+  - DBVDD1-supply
+  - gpio-controller
+  - '#gpio-cells'
+  - interrupt-controller
+  - '#interrupt-cells'
+  - interrupts
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/mfd/arizona.h>
+    i2c@e0004000 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        reg = <0xe0004000 0x1000>;
+
+        wm5102: codec@1a {
+            compatible = "wlf,wm5102";
+            reg = <0x1a>;
+
+            reset-gpios = <&gpio 0>;
+            wlf,ldoena = <&gpio 1>;
+
+            AVDD-supply = <&vdd1v8>;
+            DBVDD1-supply = <&vdd1v8>;
+            DBVDD2-supply = <&vdd1v8>;
+            DBVDD3-supply = <&vdd1v8>;
+            CPVDD-supply = <&vdd1v8>;
+            LDOVDD-supply = <&vdd1v8>;
+            SPKVDDL-supply = <&vdd5v>;
+            SPKVDDR-supply = <&vdd5v>;
+
+            interrupts = <347>;
+            interrupt-controller;
+            #interrupt-cells = <2>;
+            interrupt-parent = <&gic>;
+
+            gpio-controller;
+            #gpio-cells = <2>;
+
+            #sound-dai-cells = <1>;
+
+            wlf,gpio-defaults = <
+                ARIZONA_GP_FN_TXLRCLK
+                ARIZONA_GP_DEFAULT
+                ARIZONA_GP_DEFAULT
+                ARIZONA_GP_DEFAULT
+                ARIZONA_GP_DEFAULT
+            >;
+
+            clocks = <&clks 0>, <&clks 1>;
+            clock-names = "mclk1", "mclk2";
+
+            wlf,inmode = <ARIZONA_INMODE_DIFF ARIZONA_INMODE_DMIC>;
+            wlf,dmic-ref = <ARIZONA_DMIC_MICBIAS1 ARIZONA_DMIC_MICBIAS3>;
+
+            wlf,use-jd2;
+            wlf,use-jd2-nopull;
+            wlf,jd-invert;
+
+            wlf,micd-software-compare;
+            wlf,micd-detect-debounce = <0>;
+            wlf,micd-pol-gpio = <&codec 2 0>;
+            wlf,micd-rate = <ARIZONA_MICD_TIME_8MS>;
+            wlf,micd-dbtime = <4>;
+            wlf,micd-timeout-ms = <100>;
+            wlf,micd-force-micbias;
+            wlf,micd-configs = <0 ARIZONA_DMIC_MICBIAS1 0>,
+                               <0x2000 ARIZONA_DMIC_MICBIAS2 1>;
+
+            wlf,gpsw = <ARIZONA_GPSW_OPEN>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mfd/wm831x.txt b/Documentation/devicetree/bindings/mfd/wm831x.txt
new file mode 100644
index 000000000..6b84b1b0d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/wm831x.txt
@@ -0,0 +1,81 @@
+Cirrus Logic/Wolfson Microelectronics wm831x PMICs
+
+System PMICs with a wide range of additional features.
+
+Required properties:
+
+  - compatible : One of the following chip-specific strings:
+        "wlf,wm8310"
+        "wlf,wm8311"
+        "wlf,wm8312"
+        "wlf,wm8320"
+        "wlf,wm8321"
+        "wlf,wm8325"
+        "wlf,wm8326"
+
+  - reg : I2C slave address when connected using I2C, chip select number
+    when using SPI.
+
+  - gpio-controller : Indicates this device is a GPIO controller.
+  - #gpio-cells : Must be 2. The first cell is the pin number and the
+    second cell is used to specify optional parameters (currently unused).
+
+  - interrupts : The interrupt line the IRQ signal for the device is
+    connected to.
+
+  - interrupt-controller : wm831x devices contain interrupt controllers and
+    may provide interrupt services to other devices.
+  - #interrupt-cells: Must be 2. The first cell is the IRQ number, and the
+    second cell is the flags, encoded as the trigger masks from
+    ../interrupt-controller/interrupts.txt
+
+Optional sub-nodes:
+  - phys : Contains a phandle to the USB PHY.
+  - regulators : Contains sub-nodes for each of the regulators supplied by
+    the device. The regulators are bound using their names listed below:
+
+    dcdc1 : DCDC1
+    dcdc2 : DCDC2
+    dcdc3 : DCDC3
+    dcdc4 : DCDC3
+    isink1 : ISINK1
+    isink2 : ISINK2
+    ldo1 : LDO1
+    ldo2 : LDO2
+    ldo3 : LDO3
+    ldo4 : LDO4
+    ldo5 : LDO5
+    ldo7 : LDO7
+    ldo11 : LDO11
+
+    The bindings details of each regulator can be found in:
+    ../regulator/regulator.txt
+
+Example:
+
+wm8310: pmic@36 {
+	compatible = "wlf,wm8310";
+	reg = <0x36>;
+
+	gpio-controller;
+	#gpio-cells = <2>;
+
+	interrupts = <347>;
+	interrupt-parent = <&gic>;
+
+	interrupt-controller;
+	#interrupt-cells = <2>;
+
+	regulators {
+		dcdc1: dcdc1 {
+			regulator-name = "DCDC1";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <600000>;
+		};
+		ldo1: ldo1 {
+			regulator-name = "LDO1";
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1700000>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/xylon,logicvc.yaml b/Documentation/devicetree/bindings/mfd/xylon,logicvc.yaml
new file mode 100644
index 000000000..8a1a6625c
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/xylon,logicvc.yaml
@@ -0,0 +1,60 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright 2019 Bootlin
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/mfd/xylon,logicvc.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Xylon LogiCVC multi-function device
+
+maintainers:
+  - Paul Kocialkowski <paul.kocialkowski@bootlin.com>
+
+description: |
+  The LogiCVC is a display controller that also contains a GPIO controller.
+  As a result, a multi-function device is exposed as parent of the display
+  and GPIO blocks.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - xylon,logicvc-3.02.a
+      - const: syscon
+      - const: simple-mfd
+
+  reg:
+    maxItems: 1
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 1
+
+select:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - xylon,logicvc-3.02.a
+
+  required:
+    - compatible
+
+patternProperties:
+  "^gpio@[0-9a-f]+$":
+    $ref: /schemas/gpio/xylon,logicvc-gpio.yaml#
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    logicvc: logicvc@43c00000 {
+      compatible = "xylon,logicvc-3.02.a", "syscon", "simple-mfd";
+      reg = <0x43c00000 0x6000>;
+    };
diff --git a/Documentation/devicetree/bindings/mfd/zii,rave-sp.txt b/Documentation/devicetree/bindings/mfd/zii,rave-sp.txt
new file mode 100644
index 000000000..e0f901edc
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/zii,rave-sp.txt
@@ -0,0 +1,39 @@
+Zodiac Inflight Innovations RAVE Supervisory Processor
+
+RAVE Supervisory Processor communicates with SoC over UART. It is
+expected that its Device Tree node is specified as a child of a node
+corresponding to UART controller used for communication.
+
+Required parent device properties:
+
+ - compatible: Should be one of:
+	- "zii,rave-sp-niu"
+	- "zii,rave-sp-mezz"
+	- "zii,rave-sp-esb"
+	- "zii,rave-sp-rdu1"
+	- "zii,rave-sp-rdu2"
+
+ - current-speed: Should be set to baud rate SP device is using
+
+RAVE SP consists of the following sub-devices:
+
+Device				 Description
+------				 -----------
+rave-sp-wdt			: Watchdog
+rave-sp-nvmem			: Interface to onboard EEPROM
+rave-sp-backlight		: Display backlight
+rave-sp-hwmon			: Interface to onboard hardware sensors
+rave-sp-leds			: Interface to onboard LEDs
+rave-sp-input			: Interface to onboard power button
+
+Example of usage:
+
+	rdu {
+		compatible = "zii,rave-sp-rdu2";
+		current-speed = <1000000>;
+
+		watchdog {
+			compatible = "zii,rave-sp-watchdog";
+		};
+	};
+