Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

18 files changed, 818 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/misc/aspeed,cvic.txt b/Documentation/devicetree/bindings/misc/aspeed,cvic.txt
new file mode 100644
index 000000000..d62c783d1
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/aspeed,cvic.txt
@@ -0,0 +1,35 @@
+* ASPEED AST2400 and AST2500 coprocessor interrupt controller
+
+This file describes the bindings for the interrupt controller present
+in the AST2400 and AST2500 BMC SoCs which provides interrupt to the
+ColdFire coprocessor.
+
+It is not a normal interrupt controller and it would be rather
+inconvenient to create an interrupt tree for it as it somewhat shares
+some of the same sources as the main ARM interrupt controller but with
+different numbers.
+
+The AST2500 supports a SW generated interrupt
+
+Required properties:
+- reg: address and length of the register for the device.
+- compatible: "aspeed,cvic" and one of:
+		"aspeed,ast2400-cvic"
+	      or
+		"aspeed,ast2500-cvic"
+
+- valid-sources: One cell, bitmap of supported sources for the implementation
+
+Optional properties;
+- copro-sw-interrupts: List of interrupt numbers that can be used as
+		       SW interrupts from the ARM to the coprocessor.
+		       (AST2500 only)
+
+Example:
+
+	cvic: copro-interrupt-controller@1e6c2000 {
+		compatible = "aspeed,ast2500-cvic";
+		valid-sources = <0xffffffff>;
+		copro-sw-interrupts = <1>;
+		reg = <0x1e6c2000 0x80>;
+	};
diff --git a/Documentation/devicetree/bindings/misc/aspeed-p2a-ctrl.txt b/Documentation/devicetree/bindings/misc/aspeed-p2a-ctrl.txt
new file mode 100644
index 000000000..f2e2e28b3
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/aspeed-p2a-ctrl.txt
@@ -0,0 +1,46 @@
+======================================================================
+Device tree bindings for Aspeed AST2400/AST2500 PCI-to-AHB Bridge Control Driver
+======================================================================
+
+The bridge is available on platforms with the VGA enabled on the Aspeed device.
+In this case, the host has access to a 64KiB window into all of the BMC's
+memory.  The BMC can disable this bridge.  If the bridge is enabled, the host
+has read access to all the regions of memory, however the host only has read
+and write access depending on a register controlled by the BMC.
+
+Required properties:
+===================
+
+ - compatible: must be one of:
+	- "aspeed,ast2400-p2a-ctrl"
+	- "aspeed,ast2500-p2a-ctrl"
+
+Optional properties:
+===================
+
+- reg: A hint for the memory regions associated with the P2A controller
+- memory-region: A phandle to a reserved_memory region to be used for the PCI
+		to AHB mapping
+
+The p2a-control node should be the child of a syscon node with the required
+property:
+
+- compatible : Should be one of the following:
+		"aspeed,ast2400-scu", "syscon", "simple-mfd"
+		"aspeed,ast2500-scu", "syscon", "simple-mfd"
+
+Example
+===================
+
+g4 Example
+----------
+
+syscon: scu@1e6e2000 {
+	compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd";
+	reg = <0x1e6e2000 0x1a8>;
+
+	p2a: p2a-control {
+		compatible = "aspeed,ast2400-p2a-ctrl";
+		memory-region = <&reserved_memory>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/misc/atmel-ssc.txt b/Documentation/devicetree/bindings/misc/atmel-ssc.txt
new file mode 100644
index 000000000..f9fb41264
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/atmel-ssc.txt
@@ -0,0 +1,50 @@
+* Atmel SSC driver.
+
+Required properties:
+- compatible: "atmel,at91rm9200-ssc" or "atmel,at91sam9g45-ssc"
+	- atmel,at91rm9200-ssc: support pdc transfer
+	- atmel,at91sam9g45-ssc: support dma transfer
+- reg: Should contain SSC registers location and length
+- interrupts: Should contain SSC interrupt
+- clock-names: tuple listing input clock names.
+	Required elements: "pclk"
+- clocks: phandles to input clocks.
+
+
+Required properties for devices compatible with "atmel,at91sam9g45-ssc":
+- dmas: DMA specifier, consisting of a phandle to DMA controller node,
+  the memory interface and SSC DMA channel ID (for tx and rx).
+  See Documentation/devicetree/bindings/dma/atmel-dma.txt for details.
+- dma-names: Must be "tx", "rx".
+
+Optional properties:
+  - atmel,clk-from-rk-pin: bool property.
+     - When SSC works in slave mode, according to the hardware design, the
+       clock can get from TK pin, and also can get from RK pin. So, add
+       this parameter to choose where the clock from.
+     - By default the clock is from TK pin, if the clock from RK pin, this
+       property is needed.
+  - #sound-dai-cells: Should contain <0>.
+     - This property makes the SSC into an automatically registered DAI.
+
+Examples:
+- PDC transfer:
+ssc0: ssc@fffbc000 {
+	compatible = "atmel,at91rm9200-ssc";
+	reg = <0xfffbc000 0x4000>;
+	interrupts = <14 4 5>;
+	clocks = <&ssc0_clk>;
+	clock-names = "pclk";
+};
+
+- DMA transfer:
+ssc0: ssc@f0010000 {
+      compatible = "atmel,at91sam9g45-ssc";
+      reg = <0xf0010000 0x4000>;
+      interrupts = <28 4 5>;
+      dmas = <&dma0 1 13>,
+	     <&dma0 1 14>;
+      dma-names = "tx", "rx";
+      pinctrl-names = "default";
+      pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
+};
diff --git a/Documentation/devicetree/bindings/misc/brcm,kona-smc.txt b/Documentation/devicetree/bindings/misc/brcm,kona-smc.txt
new file mode 100644
index 000000000..05b47232e
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/brcm,kona-smc.txt
@@ -0,0 +1,15 @@
+Broadcom Secure Monitor Bounce buffer
+-----------------------------------------------------
+This binding defines the location of the bounce buffer
+used for non-secure to secure communications.
+
+Required properties:
+- compatible : "brcm,kona-smc"
+- DEPRECATED: compatible : "bcm,kona-smc"
+- reg : Location and size of bounce buffer
+
+Example:
+	smc@3404c000 {
+		compatible = "brcm,bcm11351-smc", "brcm,kona-smc";
+		reg = <0x3404c000 0x400>; //1 KiB in SRAM
+	};
diff --git a/Documentation/devicetree/bindings/misc/eeprom-93xx46.txt b/Documentation/devicetree/bindings/misc/eeprom-93xx46.txt
new file mode 100644
index 000000000..a8ebb4621
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/eeprom-93xx46.txt
@@ -0,0 +1,25 @@
+EEPROMs (SPI) compatible with Microchip Technology 93xx46 family.
+
+Required properties:
+- compatible : shall be one of:
+    "atmel,at93c46d"
+    "eeprom-93xx46"
+- data-size : number of data bits per word (either 8 or 16)
+
+Optional properties:
+- read-only : parameter-less property which disables writes to the EEPROM
+- select-gpios : if present, specifies the GPIO that will be asserted prior to
+  each access to the EEPROM (e.g. for SPI bus multiplexing)
+
+Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt
+apply.  In particular, "reg" and "spi-max-frequency" properties must be given.
+
+Example:
+	eeprom@0 {
+		compatible = "eeprom-93xx46";
+		reg = <0>;
+		spi-max-frequency = <1000000>;
+		spi-cs-high;
+		data-size = <8>;
+		select-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
+	};
diff --git a/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt b/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt
new file mode 100644
index 000000000..1442ba5d2
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt
@@ -0,0 +1,11 @@
+DPAA2 console support
+
+Required properties:
+
+    - compatible
+        Value type: <string>
+        Definition: Must be "fsl,dpaa2-console".
+    - reg
+        Value type: <prop-encoded-array>
+        Definition: A standard property.  Specifies the region where the MCFBA
+                    (MC firmware base address) register can be found.
diff --git a/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt b/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt
new file mode 100644
index 000000000..7b486d498
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt
@@ -0,0 +1,196 @@
+* Freescale Management Complex
+
+The Freescale Management Complex (fsl-mc) is a hardware resource
+manager that manages specialized hardware objects used in
+network-oriented packet processing applications. After the fsl-mc
+block is enabled, pools of hardware resources are available, such as
+queues, buffer pools, I/O interfaces. These resources are building
+blocks that can be used to create functional hardware objects/devices
+such as network interfaces, crypto accelerator instances, L2 switches,
+etc.
+
+For an overview of the DPAA2 architecture and fsl-mc bus see:
+Documentation/networking/device_drivers/ethernet/freescale/dpaa2/overview.rst
+
+As described in the above overview, all DPAA2 objects in a DPRC share the
+same hardware "isolation context" and a 10-bit value called an ICID
+(isolation context id) is expressed by the hardware to identify
+the requester.
+
+The generic 'iommus' property is insufficient to describe the relationship
+between ICIDs and IOMMUs, so an iommu-map property is used to define
+the set of possible ICIDs under a root DPRC and how they map to
+an IOMMU.
+
+For generic IOMMU bindings, see
+Documentation/devicetree/bindings/iommu/iommu.txt.
+
+For arm-smmu binding, see:
+Documentation/devicetree/bindings/iommu/arm,smmu.yaml.
+
+The MSI writes are accompanied by sideband data which is derived from the ICID.
+The msi-map property is used to associate the devices with both the ITS
+controller and the sideband data which accompanies the writes.
+
+For generic MSI bindings, see
+Documentation/devicetree/bindings/interrupt-controller/msi.txt.
+
+For GICv3 and GIC ITS bindings, see:
+Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml.
+
+Required properties:
+
+    - compatible
+        Value type: <string>
+        Definition: Must be "fsl,qoriq-mc".  A Freescale Management Complex
+                    compatible with this binding must have Block Revision
+                    Registers BRR1 and BRR2 at offset 0x0BF8 and 0x0BFC in
+                    the MC control register region.
+
+    - reg
+        Value type: <prop-encoded-array>
+        Definition: A standard property.  Specifies one or two regions
+                    defining the MC's registers:
+
+                       -the first region is the command portal for the
+                        this machine and must always be present
+
+                       -the second region is the MC control registers. This
+                        region may not be present in some scenarios, such
+                        as in the device tree presented to a virtual machine.
+
+    - ranges
+        Value type: <prop-encoded-array>
+        Definition: A standard property.  Defines the mapping between the child
+                    MC address space and the parent system address space.
+
+                    The MC address space is defined by 3 components:
+                       <region type> <offset hi> <offset lo>
+
+                    Valid values for region type are
+                       0x0 - MC portals
+                       0x1 - QBMAN portals
+
+    - #address-cells
+        Value type: <u32>
+        Definition: Must be 3.  (see definition in 'ranges' property)
+
+    - #size-cells
+        Value type: <u32>
+        Definition: Must be 1.
+
+Sub-nodes:
+
+        The fsl-mc node may optionally have dpmac sub-nodes that describe
+        the relationship between the Ethernet MACs which belong to the MC
+        and the Ethernet PHYs on the system board.
+
+        The dpmac nodes must be under a node named "dpmacs" which contains
+        the following properties:
+
+            - #address-cells
+              Value type: <u32>
+              Definition: Must be present if dpmac sub-nodes are defined and must
+                          have a value of 1.
+
+            - #size-cells
+              Value type: <u32>
+              Definition: Must be present if dpmac sub-nodes are defined and must
+                          have a value of 0.
+
+        These nodes must have the following properties:
+
+            - compatible
+              Value type: <string>
+              Definition: Must be "fsl,qoriq-mc-dpmac".
+
+            - reg
+              Value type: <prop-encoded-array>
+              Definition: Specifies the id of the dpmac.
+
+            - phy-handle
+              Value type: <phandle>
+              Definition: Specifies the phandle to the PHY device node associated
+                          with the this dpmac.
+Optional properties:
+
+- iommu-map: Maps an ICID to an IOMMU and associated iommu-specifier
+  data.
+
+  The property is an arbitrary number of tuples of
+  (icid-base,iommu,iommu-base,length).
+
+  Any ICID i in the interval [icid-base, icid-base + length) is
+  associated with the listed IOMMU, with the iommu-specifier
+  (i - icid-base + iommu-base).
+
+- msi-map: Maps an ICID to a GIC ITS and associated msi-specifier
+  data.
+
+  The property is an arbitrary number of tuples of
+  (icid-base,gic-its,msi-base,length).
+
+  Any ICID in the interval [icid-base, icid-base + length) is
+  associated with the listed GIC ITS, with the msi-specifier
+  (i - icid-base + msi-base).
+
+Deprecated properties:
+
+    - msi-parent
+        Value type: <phandle>
+        Definition: Describes the MSI controller node handling message
+                    interrupts for the MC. When there is no translation
+                    between the ICID and deviceID this property can be used
+                    to describe the MSI controller used by the devices on the
+                    mc-bus.
+                    The use of this property for mc-bus is deprecated. Please
+                    use msi-map.
+
+Example:
+
+        smmu: iommu@5000000 {
+               compatible = "arm,mmu-500";
+               #iommu-cells = <1>;
+               stream-match-mask = <0x7C00>;
+               ...
+        };
+
+        gic: interrupt-controller@6000000 {
+               compatible = "arm,gic-v3";
+               ...
+        }
+        its: gic-its@6020000 {
+               compatible = "arm,gic-v3-its";
+               msi-controller;
+               ...
+        };
+
+        fsl_mc: fsl-mc@80c000000 {
+                compatible = "fsl,qoriq-mc";
+                reg = <0x00000008 0x0c000000 0 0x40>,    /* MC portal base */
+                      <0x00000000 0x08340000 0 0x40000>; /* MC control reg */
+                /* define map for ICIDs 23-64 */
+                iommu-map = <23 &smmu 23 41>;
+                /* define msi map for ICIDs 23-64 */
+                msi-map = <23 &its 23 41>;
+                #address-cells = <3>;
+                #size-cells = <1>;
+
+                /*
+                 * Region type 0x0 - MC portals
+                 * Region type 0x1 - QBMAN portals
+                 */
+                ranges = <0x0 0x0 0x0 0x8 0x0c000000 0x4000000
+                          0x1 0x0 0x0 0x8 0x18000000 0x8000000>;
+
+                dpmacs {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    dpmac@1 {
+                        compatible = "fsl,qoriq-mc-dpmac";
+                        reg = <1>;
+                        phy-handle = <&mdio0_phy0>;
+                    }
+                }
+        };
diff --git a/Documentation/devicetree/bindings/misc/ge-achc.txt b/Documentation/devicetree/bindings/misc/ge-achc.txt
new file mode 100644
index 000000000..77df94d7a
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/ge-achc.txt
@@ -0,0 +1,26 @@
+* GE Healthcare USB Management Controller
+
+A device which handles data aquisition from compatible USB based peripherals.
+SPI is used for device management.
+
+Note: This device does not expose the peripherals as USB devices.
+
+Required properties:
+
+- compatible : Should be "ge,achc"
+
+Required SPI properties:
+
+- reg : Should be address of the device chip select within
+  the controller.
+
+- spi-max-frequency : Maximum SPI clocking speed of device in Hz, should be
+  1MHz for the GE ACHC.
+
+Example:
+
+spidev0: spi@0 {
+	compatible = "ge,achc";
+	reg = <0>;
+	spi-max-frequency = <1000000>;
+};
diff --git a/Documentation/devicetree/bindings/misc/idt_89hpesx.txt b/Documentation/devicetree/bindings/misc/idt_89hpesx.txt
new file mode 100644
index 000000000..b9093b79a
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/idt_89hpesx.txt
@@ -0,0 +1,44 @@
+EEPROM / CSR SMBus-slave interface of IDT 89HPESx devices
+
+Required properties:
+  - compatible : should be "<manufacturer>,<type>"
+		 Basically there is only one manufacturer: idt, but some
+		 compatible devices may be produced in future. Following devices
+		 are supported: 89hpes8nt2, 89hpes12nt3, 89hpes24nt6ag2,
+		 89hpes32nt8ag2, 89hpes32nt8bg2, 89hpes12nt12g2, 89hpes16nt16g2,
+		 89hpes24nt24g2, 89hpes32nt24ag2, 89hpes32nt24bg2;
+		 89hpes12n3, 89hpes12n3a, 89hpes24n3, 89hpes24n3a;
+		 89hpes32h8, 89hpes32h8g2, 89hpes48h12, 89hpes48h12g2,
+		 89hpes48h12ag2, 89hpes16h16, 89hpes22h16, 89hpes22h16g2,
+		 89hpes34h16, 89hpes34h16g2, 89hpes64h16, 89hpes64h16g2,
+		 89hpes64h16ag2;
+		 89hpes12t3g2, 89hpes24t3g2, 89hpes16t4, 89hpes4t4g2,
+		 89hpes10t4g2, 89hpes16t4g2, 89hpes16t4ag2, 89hpes5t5,
+		 89hpes6t5, 89hpes8t5, 89hpes8t5a, 89hpes24t6, 89hpes6t6g2,
+		 89hpes24t6g2, 89hpes16t7, 89hpes32t8, 89hpes32t8g2,
+		 89hpes48t12, 89hpes48t12g2.
+  - reg :	 I2C address of the IDT 89HPESx device.
+
+Optionally there can be EEPROM-compatible subnode:
+  - compatible:  There are five EEPROM devices supported: 24c32, 24c64, 24c128,
+		 24c256 and 24c512 differed by size.
+  - reg:         Custom address of EEPROM device (If not specified IDT 89HPESx
+    (optional)	 device will try to communicate with EEPROM sited by default
+		 address - 0x50)
+  - read-only :	 Parameterless property disables writes to the EEPROM
+    (optional)
+
+Example:
+	idt@60 {
+		compatible = "idt,89hpes32nt8ag2";
+		reg = <0x74>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eeprom@50 {
+			compatible = "onsemi,24c64";
+			reg = <0x50>;
+			read-only;
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/misc/ifm-csi.txt b/Documentation/devicetree/bindings/misc/ifm-csi.txt
new file mode 100644
index 000000000..5bdfffb0b
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/ifm-csi.txt
@@ -0,0 +1,41 @@
+IFM camera sensor interface on mpc5200 LocalPlus bus
+
+Required properties:
+- compatible: "ifm,o2d-csi"
+- reg: specifies sensor chip select number and associated address range
+- interrupts: external interrupt line number and interrupt sense mode
+  of the interrupt line signaling frame valid events
+- gpios: three gpio-specifiers for "capture", "reset" and "master enable"
+  GPIOs (strictly in this order).
+- ifm,csi-clk-handle: the phandle to a node in the DT describing the sensor
+  clock generator. This node is usually a general purpose timer controller.
+- ifm,csi-addr-bus-width: address bus width (valid values are 16, 24, 25)
+- ifm,csi-data-bus-width: data bus width (valid values are 8 and 16)
+- ifm,csi-wait-cycles: sensor bus wait cycles
+
+Optional properties:
+- ifm,csi-byte-swap: if this property is present, the byte swapping on
+  the bus will be enabled.
+
+Example:
+
+	csi@3,0 {
+		compatible = "ifm,o2d-csi";
+		reg = <3 0 0x00100000>;		/* CS 3, 1 MiB range */
+		interrupts = <1 1 2>;		/* IRQ1, edge falling */
+
+		ifm,csi-clk-handle = <&timer7>;
+		gpios = <&gpio_simple 23 0	/* image_capture */
+			 &gpio_simple 26 0	/* image_reset */
+			 &gpio_simple 29 0>;	/* image_master_en */
+
+		ifm,csi-addr-bus-width = <24>;
+		ifm,csi-data-bus-width = <8>;
+		ifm,csi-wait-cycles = <0>;
+	};
+
+The base address of the used chip select is specified in the
+ranges property of the parent localbus node, for example:
+
+	ranges = <0 0 0xff000000 0x01000000
+		  3 0 0xe3000000 0x00100000>;
diff --git a/Documentation/devicetree/bindings/misc/intel,ixp4xx-ahb-queue-manager.yaml b/Documentation/devicetree/bindings/misc/intel,ixp4xx-ahb-queue-manager.yaml
new file mode 100644
index 000000000..38ab04991
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/intel,ixp4xx-ahb-queue-manager.yaml
@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright 2019 Linaro Ltd.
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/misc/intel,ixp4xx-ahb-queue-manager.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Intel IXP4xx AHB Queue Manager
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+description: |
+  The IXP4xx AHB Queue Manager maintains queues as circular buffers in
+  an 8KB embedded SRAM along with hardware pointers. It is used by both
+  the XScale processor and the NPEs (Network Processing Units) in the
+  IXP4xx for accelerating queues, especially for networking. Clients pick
+  queues from the queue manager with foo-queue = <&qmgr N> where the
+  &qmgr is a phandle to the queue manager and N is the queue resource
+  number. The queue resources available and their specific purpose
+  on a certain IXP4xx system will vary.
+
+properties:
+  compatible:
+    items:
+      - const: intel,ixp4xx-ahb-queue-manager
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    items:
+      - description: Interrupt for queues 0-31
+      - description: Interrupt for queues 32-63
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    qmgr: queue-manager@60000000 {
+         compatible = "intel,ixp4xx-ahb-queue-manager";
+         reg = <0x60000000 0x4000>;
+         interrupts = <3 IRQ_TYPE_LEVEL_HIGH>, <4 IRQ_TYPE_LEVEL_HIGH>;
+    };
diff --git a/Documentation/devicetree/bindings/misc/lwn-bk4.txt b/Documentation/devicetree/bindings/misc/lwn-bk4.txt
new file mode 100644
index 000000000..d6a8c188c
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/lwn-bk4.txt
@@ -0,0 +1,26 @@
+* Liebherr's BK4 controller external SPI
+
+A device which handles data acquisition from compatible industrial
+peripherals.
+The SPI is used for data and management purposes in both master and
+slave modes.
+
+Required properties:
+
+- compatible : Should be "lwn,bk4"
+
+Required SPI properties:
+
+- reg : Should be address of the device chip select within
+  the controller.
+
+- spi-max-frequency : Maximum SPI clocking speed of device in Hz, should be
+  30MHz at most for the Liebherr's BK4 external bus.
+
+Example:
+
+spidev0: spi@0 {
+	compatible = "lwn,bk4";
+	spi-max-frequency = <30000000>;
+	reg = <0>;
+};
diff --git a/Documentation/devicetree/bindings/misc/nvidia,tegra186-misc.txt b/Documentation/devicetree/bindings/misc/nvidia,tegra186-misc.txt
new file mode 100644
index 000000000..43d777ed8
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/nvidia,tegra186-misc.txt
@@ -0,0 +1,14 @@
+NVIDIA Tegra186 (and later) MISC register block
+
+The MISC register block found on Tegra186 and later SoCs contains registers
+that can be used to identify a given chip and various strapping options.
+
+Required properties:
+- compatible: Must be:
+  - Tegra186: "nvidia,tegra186-misc"
+  - Tegra194: "nvidia,tegra194-misc"
+  - Tegra234: "nvidia,tegra234-misc"
+- reg: Should contain 2 entries: The first entry gives the physical address
+       and length of the register region which contains revision and debug
+       features. The second entry specifies the physical address and length
+       of the register region indicating the strapping options.
diff --git a/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt b/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt
new file mode 100644
index 000000000..83f6a251b
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt
@@ -0,0 +1,17 @@
+NVIDIA Tegra APBMISC block
+
+Required properties:
+- compatible: Must be:
+  - Tegra20: "nvidia,tegra20-apbmisc"
+  - Tegra30: "nvidia,tegra30-apbmisc", "nvidia,tegra20-apbmisc"
+  - Tegra114: "nvidia,tegra114-apbmisc", "nvidia,tegra20-apbmisc"
+  - Tegra124: "nvidia,tegra124-apbmisc", "nvidia,tegra20-apbmisc"
+  - Tegra132: "nvidia,tegra124-apbmisc", "nvidia,tegra20-apbmisc"
+  - Tegra210: "nvidia,tegra210-apbmisc", "nvidia,tegra20-apbmisc"
+- reg: Should contain 2 entries: the first entry gives the physical address
+       and length of the registers which contain revision and debug features.
+       The second entry gives the physical address and length of the
+       registers indicating the strapping options.
+
+Optional properties:
+- nvidia,long-ram-code: If present, the RAM code is long (4 bit). If not, short (2 bit).
diff --git a/Documentation/devicetree/bindings/misc/olpc,xo1.75-ec.yaml b/Documentation/devicetree/bindings/misc/olpc,xo1.75-ec.yaml
new file mode 100644
index 000000000..b3c45c046
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/olpc,xo1.75-ec.yaml
@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+# Copyright (C) 2019,2020 Lubomir Rintel <lkundrak@v3.sk>
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/misc/olpc,xo1.75-ec.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: OLPC XO-1.75 Embedded Controller bindings
+
+description: |
+  This binding describes the Embedded Controller acting as a SPI bus master
+  on a OLPC XO-1.75 laptop computer.
+
+  The embedded controller requires the SPI controller driver to signal
+  readiness to receive a transfer (that is, when TX FIFO contains the
+  response data) by strobing the ACK pin with the ready signal. See the
+  "ready-gpios" property of the SSP binding as documented in:
+  <Documentation/devicetree/bindings/spi/marvell,mmp2-ssp.yaml>.
+
+maintainers:
+  - Lubomir Rintel <lkundrak@v3.sk>
+
+properties:
+  compatible:
+    const: olpc,xo1.75-ec
+
+  cmd-gpios:
+    description: GPIO uspecifier of the CMD pin
+    maxItems: 1
+
+  spi-cpha: true
+
+required:
+  - compatible
+  - cmd-gpios
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    spi {
+      spi-slave;
+      #address-cells = <0>;
+      #size-cells = <0>;
+      ready-gpios = <&gpio 125 GPIO_ACTIVE_HIGH>;
+
+      slave {
+        compatible = "olpc,xo1.75-ec";
+        spi-cpha;
+        cmd-gpios = <&gpio 155 GPIO_ACTIVE_HIGH>;
+      };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/misc/pvpanic-mmio.txt b/Documentation/devicetree/bindings/misc/pvpanic-mmio.txt
new file mode 100644
index 000000000..985e90736
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/pvpanic-mmio.txt
@@ -0,0 +1,29 @@
+* QEMU PVPANIC MMIO Configuration bindings
+
+QEMU's emulation / virtualization targets provide the following PVPANIC
+MMIO Configuration interface on the "virt" machine.
+type:
+
+- a read-write, 16-bit wide data register.
+
+QEMU exposes the data register to guests as memory mapped registers.
+
+Required properties:
+
+- compatible: "qemu,pvpanic-mmio".
+- reg: the MMIO region used by the device.
+  * Bytes 0x0  Write panic event to the reg when guest OS panics.
+  * Bytes 0x1  Reserved.
+
+Example:
+
+/ {
+        #size-cells = <0x2>;
+        #address-cells = <0x2>;
+
+        pvpanic-mmio@9060000 {
+                compatible = "qemu,pvpanic-mmio";
+                reg = <0x0 0x9060000 0x0 0x2>;
+        };
+};
+
diff --git a/Documentation/devicetree/bindings/misc/qcom,fastrpc.txt b/Documentation/devicetree/bindings/misc/qcom,fastrpc.txt
new file mode 100644
index 000000000..2a1827ab5
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/qcom,fastrpc.txt
@@ -0,0 +1,78 @@
+Qualcomm Technologies, Inc. FastRPC Driver
+
+The FastRPC implements an IPC (Inter-Processor Communication)
+mechanism that allows for clients to transparently make remote method
+invocations across DSP and APPS boundaries. This enables developers
+to offload tasks to the DSP and free up the application processor for
+other tasks.
+
+- compatible:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must be "qcom,fastrpc"
+
+- label
+	Usage: required
+	Value type: <string>
+	Definition: should specify the dsp domain name this fastrpc
+	corresponds to. must be one of this: "adsp", "mdsp", "sdsp", "cdsp"
+
+- #address-cells
+	Usage: required
+	Value type: <u32>
+	Definition: Must be 1
+
+- #size-cells
+	Usage: required
+	Value type: <u32>
+	Definition: Must be 0
+
+= COMPUTE BANKS
+Each subnode of the Fastrpc represents compute context banks available
+on the dsp.
+- All Compute context banks MUST contain the following properties:
+
+- compatible:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must be "qcom,fastrpc-compute-cb"
+
+- reg
+	Usage: required
+	Value type: <u32>
+	Definition: Context Bank ID.
+
+- qcom,nsessions:
+	Usage: Optional
+	Value type: <u32>
+	Defination: A value indicating how many sessions can share this
+		    context bank. Defaults to 1 when this property
+		    is not specified.
+
+Example:
+
+adsp-pil {
+	compatible = "qcom,msm8996-adsp-pil";
+	...
+	smd-edge {
+		label = "lpass";
+		fastrpc {
+			compatible = "qcom,fastrpc";
+			qcom,smd-channels = "fastrpcsmd-apps-dsp";
+			label = "adsp";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cb@1 {
+				compatible = "qcom,fastrpc-compute-cb";
+				reg = <1>;
+			};
+
+			cb@2 {
+				compatible = "qcom,fastrpc-compute-cb";
+				reg = <2>;
+			};
+			...
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/misc/xlnx,sd-fec.txt b/Documentation/devicetree/bindings/misc/xlnx,sd-fec.txt
new file mode 100644
index 000000000..e3289634f
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/xlnx,sd-fec.txt
@@ -0,0 +1,58 @@
+* Xilinx SDFEC(16nm) IP *
+
+The Soft Decision Forward Error Correction (SDFEC) Engine is a Hard IP block
+which provides high-throughput LDPC and Turbo Code implementations.
+The LDPC decode & encode functionality is capable of covering a range of
+customer specified Quasi-cyclic (QC) codes. The Turbo decode functionality
+principally covers codes used by LTE. The FEC Engine offers significant
+power and area savings versus implementations done in the FPGA fabric.
+
+
+Required properties:
+- compatible: Must be "xlnx,sd-fec-1.1"
+- clock-names : List of input clock names from the following:
+    - "core_clk", Main processing clock for processing core (required)
+    - "s_axi_aclk", AXI4-Lite memory-mapped slave interface clock (required)
+    - "s_axis_din_aclk", DIN AXI4-Stream Slave interface clock (optional)
+    - "s_axis_din_words-aclk", DIN_WORDS AXI4-Stream Slave interface clock (optional)
+    - "s_axis_ctrl_aclk",  Control input AXI4-Stream Slave interface clock (optional)
+    - "m_axis_dout_aclk", DOUT AXI4-Stream Master interface clock (optional)
+    - "m_axis_dout_words_aclk", DOUT_WORDS AXI4-Stream Master interface clock (optional)
+    - "m_axis_status_aclk", Status output AXI4-Stream Master interface clock (optional)
+- clocks : Clock phandles (see clock_bindings.txt for details).
+- reg: Should contain Xilinx SDFEC 16nm Hardened IP block registers
+  location and length.
+- xlnx,sdfec-code : Should contain "ldpc" or "turbo" to describe the codes
+  being used.
+- xlnx,sdfec-din-words : A value 0 indicates that the DIN_WORDS interface is
+  driven with a fixed value and is not present on the device, a value of 1
+  configures the DIN_WORDS to be block based, while a value of 2 configures the
+  DIN_WORDS input to be supplied for each AXI transaction.
+- xlnx,sdfec-din-width : Configures the DIN AXI stream where a value of 1
+  configures a width of "1x128b", 2 a width of "2x128b" and 4 configures a width
+  of "4x128b".
+- xlnx,sdfec-dout-words : A value 0 indicates that the DOUT_WORDS interface is
+  driven with a fixed value and is not present on the device, a value of 1
+  configures the DOUT_WORDS to be block based, while a value of 2 configures the
+  DOUT_WORDS input to be supplied for each AXI transaction.
+- xlnx,sdfec-dout-width : Configures the DOUT AXI stream where a value of 1
+  configures a width of "1x128b", 2 a width of "2x128b" and 4 configures a width
+  of "4x128b".
+Optional properties:
+- interrupts: should contain SDFEC interrupt number
+
+Example
+---------------------------------------
+	sd_fec_0: sd-fec@a0040000 {
+		compatible = "xlnx,sd-fec-1.1";
+		clock-names = "core_clk","s_axi_aclk","s_axis_ctrl_aclk","s_axis_din_aclk","m_axis_status_aclk","m_axis_dout_aclk";
+		clocks = <&misc_clk_2>,<&misc_clk_0>,<&misc_clk_1>,<&misc_clk_1>,<&misc_clk_1>, <&misc_clk_1>;
+		reg = <0x0 0xa0040000 0x0 0x40000>;
+		interrupt-parent = <&axi_intc>;
+		interrupts = <1 0>;
+		xlnx,sdfec-code = "ldpc";
+		xlnx,sdfec-din-words = <0>;
+		xlnx,sdfec-din-width = <2>;
+		xlnx,sdfec-dout-words = <0>;
+		xlnx,sdfec-dout-width = <1>;
+	};