Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 102 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/dsa/lan9303.txt b/Documentation/devicetree/bindings/net/dsa/lan9303.txt
new file mode 100644
index 000000000..464d6bf87
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/lan9303.txt
@@ -0,0 +1,102 @@
+SMSC/MicroChip LAN9303 three port ethernet switch
+-------------------------------------------------
+
+Required properties:
+
+- compatible: should be
+  - "smsc,lan9303-i2c" for I2C managed mode
+    or
+  - "smsc,lan9303-mdio" for mdio managed mode
+
+Optional properties:
+
+- reset-gpios: GPIO to be used to reset the whole device
+- reset-duration: reset duration in milliseconds, defaults to 200 ms
+
+Subnodes:
+
+The integrated switch subnode should be specified according to the binding
+described in dsa/dsa.txt. The CPU port of this switch is always port 0.
+
+Note: always use 'reg = <0/1/2>;' for the three DSA ports, even if the device is
+configured to use 1/2/3 instead. This hardware configuration will be
+auto-detected and mapped accordingly.
+
+Example:
+
+I2C managed mode:
+
+	master: masterdevice@X {
+
+		fixed-link { /* RMII fixed link to LAN9303 */
+			speed = <100>;
+			full-duplex;
+		};
+	};
+
+	switch: switch@a {
+		compatible = "smsc,lan9303-i2c";
+		reg = <0xa>;
+		reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
+		reset-duration = <200>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 { /* RMII fixed link to master */
+				reg = <0>;
+				label = "cpu";
+				ethernet = <&master>;
+			};
+
+			port@1 { /* external port 1 */
+				reg = <1>;
+				label = "lan1";
+			};
+
+			port@2 { /* external port 2 */
+				reg = <2>;
+				label = "lan2";
+			};
+		};
+	};
+
+MDIO managed mode:
+
+	master: masterdevice@X {
+		phy-handle = <&switch>;
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch: switch-phy@0 {
+				compatible = "smsc,lan9303-mdio";
+				reg = <0>;
+				reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
+				reset-duration = <100>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						label = "cpu";
+						ethernet = <&master>;
+					};
+
+					port@1 { /* external port 1 */
+						reg = <1>;
+						label = "lan1";
+					};
+
+					port@2 { /* external port 2 */
+						reg = <2>;
+						label = "lan2";
+					};
+				};
+			};
+		};
+	};