Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 90 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt
new file mode 100644
index 000000000..8ee4b1ced
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt
@@ -0,0 +1,90 @@
+Hisilicon DSA Fabric device controller
+
+Required properties:
+- compatible: should be "hisilicon,hns-dsaf-v1" or "hisilicon,hns-dsaf-v2".
+  "hisilicon,hns-dsaf-v1" is for hip05.
+  "hisilicon,hns-dsaf-v2" is for Hi1610 and Hi1612.
+- mode: dsa fabric mode string. only support one of dsaf modes like these:
+		"2port-64vf",
+		"6port-16rss",
+		"6port-16vf",
+		"single-port".
+- interrupts: should contain the DSA Fabric and rcb interrupt.
+- reg: specifies base physical address(es) and size of the device registers.
+  The first region is external interface control register base and size(optional,
+  only used when subctrl-syscon does not exist). It is recommended using
+  subctrl-syscon rather than this address.
+  The second region is SerDes base register and size(optional, only used when
+  serdes-syscon in port node does not exist). It is recommended using
+  serdes-syscon rather than this address.
+  The third region is the PPE register base and size.
+  The fourth region is dsa fabric base register and size. It is not required for
+  single-port mode.
+- reg-names: may be ppe-base and(or) dsaf-base. It is used to find the
+  corresponding reg's index.
+
+- phy-handle: phy handle of physical port, 0 if not any phy device. It is optional
+  attribute. If port node exists, phy-handle in each port node will be used.
+  see ethernet.txt [1].
+- subctrl-syscon: is syscon handle for external interface control register.
+- reset-field-offset: is offset of reset field. Its value depends on the hardware
+  user manual.
+- buf-size: rx buffer size, should be 16-1024.
+- desc-num: number of description in TX and RX queue, should be 512, 1024, 2048 or 4096.
+
+- port: subnodes of dsaf. A dsaf node may contain several port nodes(Depending
+  on mode of dsaf). Port node contain some attributes listed below:
+- reg: is physical port index in one dsaf.
+- phy-handle: phy handle of physical port. It is not required if there isn't
+  phy device. see ethernet.txt [1].
+- serdes-syscon: is syscon handle for SerDes register.
+- cpld-syscon: is syscon handle + register offset pair for cpld register. It is
+  not required if there isn't cpld device.
+- port-rst-offset: is offset of reset field for each port in dsaf. Its value
+  depends on the hardware user manual.
+- port-mode-offset: is offset of port mode field for each port in dsaf. Its
+  value depends on the hardware user manual.
+- mc-mac-mask: mask of multicast address, determines bit in multicast address
+  to set:
+  1 stands for this bit will be precisely matched, TCAM will check this bit of
+    MAC address.
+  0 stands for this bit will be fuzzy matched, TCAM won't care about this bit
+    of MAC address.
+
+[1] Documentation/devicetree/bindings/net/phy.txt
+
+Example:
+
+dsaf0: dsa@c7000000 {
+	compatible = "hisilicon,hns-dsaf-v1";
+	mode = "6port-16rss";
+	interrupt-parent = <&mbigen_dsa>;
+	reg = <0x0 0xc5000000 0x0 0x890000
+	       0x0 0xc7000000 0x0 0x60000>;
+	reg-names = "ppe-base", "dsaf-base";
+	subctrl-syscon = <&subctrl>;
+	reset-field-offset = 0;
+	interrupts = <131 4>,<132 4>, <133 4>,<134 4>,
+		     <135 4>,<136 4>, <137 4>,<138 4>,
+		     <139 4>,<140 4>, <141 4>,<142 4>,
+		     <143 4>,<144 4>, <145 4>,<146 4>,
+		     <147 4>,<148 4>, <384 1>,<385 1>,
+		     <386 1>,<387 1>, <388 1>,<389 1>,
+		     <390 1>,<391 1>,
+	buf-size = <4096>;
+	desc-num = <1024>;
+	dma-coherent;
+
+	port@0 {
+		reg = 0;
+		phy-handle = <&phy0>;
+		serdes-syscon = <&serdes>;
+		mc-mac-mask = [ff f0 00 00 00 00];
+	};
+
+	port@1 {
+                reg = 1;
+                serdes-syscon = <&serdes>;
+		mc-mac-mask = [ff f0 00 00 00 00];
+        };
+};