Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 116 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt
new file mode 100644
index 000000000..9ef5bacda
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt
@@ -0,0 +1,116 @@
+MediaTek SoC built-in Bluetooth Devices
+==================================
+
+This device is a serial attached device to BTIF device and thus it must be a
+child node of the serial node with BTIF. The dt-bindings details for BTIF
+device can be known via Documentation/devicetree/bindings/serial/8250.yaml.
+
+Required properties:
+
+- compatible:	Must be
+		  "mediatek,mt7622-bluetooth": for MT7622 SoC
+- clocks:	Should be the clock specifiers corresponding to the entry in
+		clock-names property.
+- clock-names:	Should contain "ref" entries.
+- power-domains: Phandle to the power domain that the device is part of
+
+Example:
+
+	btif: serial@1100c000 {
+		compatible = "mediatek,mt7622-btif",
+			     "mediatek,mtk-btif";
+		reg = <0 0x1100c000 0 0x1000>;
+		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&pericfg CLK_PERI_BTIF_PD>;
+		clock-names = "main";
+		reg-shift = <2>;
+		reg-io-width = <4>;
+
+		bluetooth {
+			compatible = "mediatek,mt7622-bluetooth";
+			power-domains = <&scpsys MT7622_POWER_DOMAIN_WB>;
+			clocks = <&clk25m>;
+			clock-names = "ref";
+		};
+	};
+
+MediaTek UART based Bluetooth Devices
+==================================
+
+This device is a serial attached device to UART device and thus it must be a
+child node of the serial node with UART.
+
+Please refer to the following documents for generic properties:
+
+	Documentation/devicetree/bindings/serial/serial.yaml
+
+Required properties:
+
+- compatible:	Must be
+		  "mediatek,mt7663u-bluetooth": for MT7663U device
+		  "mediatek,mt7668u-bluetooth": for MT7668U device
+- vcc-supply:	Main voltage regulator
+
+If the pin controller on the platform can support both pinmux and GPIO
+control such as the most of MediaTek platform. Please use below properties.
+
+- pinctrl-names: Should be "default", "runtime"
+- pinctrl-0: Should contain UART RXD low when the device is powered up to
+	     enter proper bootstrap mode.
+- pinctrl-1: Should contain UART mode pin ctrl
+
+Else, the pin controller on the platform only can support pinmux control and
+the GPIO control still has to rely on the dedicated GPIO controller such as
+a legacy MediaTek SoC, MT7621. Please use the below properties.
+
+- boot-gpios:	GPIO same to the pin as UART RXD and used to keep LOW when
+		the device is powered up to enter proper bootstrap mode when
+- pinctrl-names: Should be "default"
+- pinctrl-0: Should contain UART mode pin ctrl
+
+Optional properties:
+
+- reset-gpios:	GPIO used to reset the device whose initial state keeps low,
+		if the GPIO is missing, then board-level design should be
+		guaranteed.
+- clocks:	Should be the clock specifiers corresponding to the entry in
+		clock-names property. If the clock is missing, then board-level
+		design should be guaranteed.
+- clock-names:	Should contain "osc" entry for the external oscillator.
+- current-speed:  Current baud rate of the device whose defaults to 921600
+
+Example:
+
+	uart1_pins_boot: uart1-default {
+		pins-dat {
+			pinmux = <MT7623_PIN_81_URXD1_FUNC_GPIO81>;
+			output-low;
+		};
+	};
+
+	uart1_pins_runtime: uart1-runtime {
+		pins-dat {
+			pinmux = <MT7623_PIN_81_URXD1_FUNC_URXD1>,
+				 <MT7623_PIN_82_UTXD1_FUNC_UTXD1>;
+		};
+	};
+
+	uart1: serial@11003000 {
+		compatible = "mediatek,mt7623-uart",
+			     "mediatek,mt6577-uart";
+		reg = <0 0x11003000 0 0x400>;
+		interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&pericfg CLK_PERI_UART1_SEL>,
+			 <&pericfg CLK_PERI_UART1>;
+		clock-names = "baud", "bus";
+
+		bluetooth {
+			compatible = "mediatek,mt7663u-bluetooth";
+			vcc-supply = <&reg_5v>;
+			reset-gpios = <&pio 24 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default", "runtime";
+			pinctrl-0 = <&uart1_pins_boot>;
+			pinctrl-1 = <&uart1_pins_runtime>;
+			current-speed = <921600>;
+		};
+	};