Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 129 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.yaml b/Documentation/devicetree/bindings/net/ti,dp83867.yaml
new file mode 100644
index 000000000..4050a3608
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/ti,dp83867.yaml
@@ -0,0 +1,129 @@
+# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause)
+# Copyright (C) 2019 Texas Instruments Incorporated
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/net/ti,dp83867.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: TI DP83867 ethernet PHY
+
+allOf:
+  - $ref: "ethernet-controller.yaml#"
+
+maintainers:
+  - Dan Murphy <dmurphy@ti.com>
+
+description: |
+  The DP83867 device is a robust, low power, fully featured Physical Layer
+  transceiver with integrated PMD sublayers to support 10BASE-Te, 100BASE-TX
+  and 1000BASE-T Ethernet protocols.
+
+  The DP83867 is designed for easy implementation of 10/100/1000 Mbps Ethernet
+  LANs. It interfaces directly to twisted pair media via an external
+  transformer. This device interfaces directly to the MAC layer through the
+  IEEE 802.3 Standard Media Independent Interface (MII), the IEEE 802.3 Gigabit
+  Media Independent Interface (GMII) or Reduced GMII (RGMII).
+
+  Specifications about the Ethernet PHY can be found at:
+    https://www.ti.com/lit/gpn/dp83867ir
+
+properties:
+  reg:
+    maxItems: 1
+
+  ti,min-output-impedance:
+    type: boolean
+    description: |
+       MAC Interface Impedance control to set the programmable output impedance
+       to a minimum value (35 ohms).
+
+  ti,max-output-impedance:
+    type: boolean
+    description: |
+      MAC Interface Impedance control to set the programmable output impedance
+      to a maximum value (70 ohms).
+      Note: ti,min-output-impedance and ti,max-output-impedance are mutually
+        exclusive. When both properties are present ti,max-output-impedance
+        takes precedence.
+
+  tx-fifo-depth:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description: |
+       Transmitt FIFO depth see dt-bindings/net/ti-dp83867.h for values
+
+  rx-fifo-depth:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description: |
+       Receive FIFO depth see dt-bindings/net/ti-dp83867.h for values
+
+  ti,clk-output-sel:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description: |
+      Muxing option for CLK_OUT pin.  See dt-bindings/net/ti-dp83867.h
+      for applicable values. The CLK_OUT pin can also be disabled by this
+      property.  When omitted, the PHY's default will be left as is.
+
+  ti,rx-internal-delay:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description: |
+      RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h
+      for applicable values. Required only if interface type is
+      PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_RXID.
+
+  ti,tx-internal-delay:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description: |
+      RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h
+      for applicable values. Required only if interface type is
+      PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_TXID.
+
+        Note: If the interface type is PHY_INTERFACE_MODE_RGMII the TX/RX clock
+          delays will be left at their default values, as set by the PHY's pin
+          strapping. The default strapping will use a delay of 2.00 ns.  Thus
+          PHY_INTERFACE_MODE_RGMII, by default, does not behave as RGMII with no
+          internal delay, but as PHY_INTERFACE_MODE_RGMII_ID.  The device tree
+          should use "rgmii-id" if internal delays are desired as this may be
+          changed in future to cause "rgmii" mode to disable delays.
+
+  ti,dp83867-rxctrl-strap-quirk:
+    type: boolean
+    description: |
+      This denotes the fact that the board has RX_DV/RX_CTRL pin strapped in
+      mode 1 or 2. To ensure PHY operation, there are specific actions that
+      software needs to take when this pin is strapped in these modes.
+      See data manual for details.
+
+  ti,sgmii-ref-clock-output-enable:
+    type: boolean
+    description: |
+      This denotes which SGMII configuration is used (4 or 6-wire modes).
+      Some MACs work with differential SGMII clock. See data manual for details.
+
+  ti,fifo-depth:
+    deprecated: true
+    $ref: /schemas/types.yaml#definitions/uint32
+    description: |
+      Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h for applicable
+      values.
+
+required:
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/net/ti-dp83867.h>
+    mdio0 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      ethphy0: ethernet-phy@0 {
+        reg = <0>;
+        tx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+        rx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+        ti,max-output-impedance;
+        ti,clk-output-sel = <DP83867_CLK_O_SEL_CHN_A_RCLK>;
+        ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+        ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+      };
+    };