Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 135 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt b/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt
new file mode 100644
index 000000000..5f8cb4962
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt
@@ -0,0 +1,135 @@
+Faraday Technology FTPCI100 PCI Host Bridge
+
+This PCI bridge is found inside that Cortina Systems Gemini SoC platform and
+is a generic IP block from Faraday Technology. It exists in two variants:
+plain and dual PCI. The plain version embeds a cascading interrupt controller
+into the host bridge. The dual version routes the interrupts to the host
+chips interrupt controller.
+
+The host controller appear on the PCI bus with vendor ID 0x159b (Faraday
+Technology) and product ID 0x4321.
+
+Mandatory properties:
+
+- compatible: ranging from specific to generic, should be one of
+  "cortina,gemini-pci", "faraday,ftpci100"
+  "cortina,gemini-pci-dual", "faraday,ftpci100-dual"
+  "faraday,ftpci100"
+  "faraday,ftpci100-dual"
+- reg: memory base and size for the host bridge
+- #address-cells: set to <3>
+- #size-cells: set to <2>
+- #interrupt-cells: set to <1>
+- bus-range: set to <0x00 0xff>
+- device_type, set to "pci"
+- ranges: see pci.txt
+- interrupt-map-mask: see pci.txt
+- interrupt-map: see pci.txt
+- dma-ranges: three ranges for the inbound memory region. The ranges must
+  be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, 64MB,
+  128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked as
+  pre-fetchable.
+
+Optional properties:
+- clocks: when present, this should contain the peripheral clock (PCLK) and the
+  PCI clock (PCICLK). If these are not present, they are assumed to be
+  hard-wired enabled and always on. The PCI clock will be 33 or 66 MHz.
+- clock-names: when present, this should contain "PCLK" for the peripheral
+  clock and "PCICLK" for the PCI-side clock.
+
+Mandatory subnodes:
+- For "faraday,ftpci100" a node representing the interrupt-controller inside the
+  host bridge is mandatory. It has the following mandatory properties:
+  - interrupt: see interrupt-controller/interrupts.txt
+  - interrupt-controller: see interrupt-controller/interrupts.txt
+  - #address-cells: set to <0>
+  - #interrupt-cells: set to <1>
+
+I/O space considerations:
+
+The plain variant has 128MiB of non-prefetchable memory space, whereas the
+"dual" variant has 64MiB. Take this into account when describing the ranges.
+
+Interrupt map considerations:
+
+The "dual" variant will get INT A, B, C, D from the system interrupt controller
+and should point to respective interrupt in that controller in its
+interrupt-map.
+
+The code which is the only documentation of how the Faraday PCI (the non-dual
+variant) interrupts assigns the default interrupt mapping/swizzling has
+typically been like this, doing the swizzling on the interrupt controller side
+rather than in the interconnect:
+
+interrupt-map-mask = <0xf800 0 0 7>;
+interrupt-map =
+	<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
+	<0x4800 0 0 2 &pci_intc 1>,
+	<0x4800 0 0 3 &pci_intc 2>,
+	<0x4800 0 0 4 &pci_intc 3>,
+	<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
+	<0x5000 0 0 2 &pci_intc 2>,
+	<0x5000 0 0 3 &pci_intc 3>,
+	<0x5000 0 0 4 &pci_intc 0>,
+	<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
+	<0x5800 0 0 2 &pci_intc 3>,
+	<0x5800 0 0 3 &pci_intc 0>,
+	<0x5800 0 0 4 &pci_intc 1>,
+	<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
+	<0x6000 0 0 2 &pci_intc 0>,
+	<0x6000 0 0 3 &pci_intc 1>,
+	<0x6000 0 0 4 &pci_intc 2>;
+
+Example:
+
+pci@50000000 {
+	compatible = "cortina,gemini-pci", "faraday,ftpci100";
+	reg = <0x50000000 0x100>;
+	interrupts = <8 IRQ_TYPE_LEVEL_HIGH>, /* PCI A */
+			<26 IRQ_TYPE_LEVEL_HIGH>, /* PCI B */
+			<27 IRQ_TYPE_LEVEL_HIGH>, /* PCI C */
+			<28 IRQ_TYPE_LEVEL_HIGH>; /* PCI D */
+	#address-cells = <3>;
+	#size-cells = <2>;
+	#interrupt-cells = <1>;
+
+	bus-range = <0x00 0xff>;
+	ranges = /* 1MiB I/O space 0x50000000-0x500fffff */
+		 <0x01000000 0 0          0x50000000 0 0x00100000>,
+		 /* 128MiB non-prefetchable memory 0x58000000-0x5fffffff */
+		 <0x02000000 0 0x58000000 0x58000000 0 0x08000000>;
+
+	/* DMA ranges */
+	dma-ranges =
+	/* 128MiB at 0x00000000-0x07ffffff */
+	<0x02000000 0 0x00000000 0x00000000 0 0x08000000>,
+	/* 64MiB at 0x00000000-0x03ffffff */
+	<0x02000000 0 0x00000000 0x00000000 0 0x04000000>,
+	/* 64MiB at 0x00000000-0x03ffffff */
+	<0x02000000 0 0x00000000 0x00000000 0 0x04000000>;
+
+	interrupt-map-mask = <0xf800 0 0 7>;
+	interrupt-map =
+		<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
+		<0x4800 0 0 2 &pci_intc 1>,
+		<0x4800 0 0 3 &pci_intc 2>,
+		<0x4800 0 0 4 &pci_intc 3>,
+		<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
+		<0x5000 0 0 2 &pci_intc 2>,
+		<0x5000 0 0 3 &pci_intc 3>,
+		<0x5000 0 0 4 &pci_intc 0>,
+		<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
+		<0x5800 0 0 2 &pci_intc 3>,
+		<0x5800 0 0 3 &pci_intc 0>,
+		<0x5800 0 0 4 &pci_intc 1>,
+		<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
+		<0x6000 0 0 2 &pci_intc 0>,
+		<0x6000 0 0 3 &pci_intc 0>,
+		<0x6000 0 0 4 &pci_intc 0>;
+	pci_intc: interrupt-controller {
+		interrupt-parent = <&intcon>;
+		interrupt-controller;
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+	};
+};