Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 380 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
new file mode 100644
index 000000000..7734ab6fe
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
@@ -0,0 +1,380 @@
+Samsung GPIO and Pin Mux/Config controller
+
+Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware
+controller. It controls the input/output settings on the available pads/pins
+and also provides ability to multiplex and configure the output of various
+on-chip controllers onto these pads.
+
+Required Properties:
+- compatible: should be one of the following.
+  - "samsung,s3c2412-pinctrl": for S3C2412-compatible pin-controller,
+  - "samsung,s3c2416-pinctrl": for S3C2416-compatible pin-controller,
+  - "samsung,s3c2440-pinctrl": for S3C2440-compatible pin-controller,
+  - "samsung,s3c2450-pinctrl": for S3C2450-compatible pin-controller,
+  - "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller,
+  - "samsung,s5pv210-pinctrl": for S5PV210-compatible pin-controller,
+  - "samsung,exynos3250-pinctrl": for Exynos3250 compatible pin-controller.
+  - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller.
+  - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller.
+  - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller.
+  - "samsung,exynos5260-pinctrl": for Exynos5260 compatible pin-controller.
+  - "samsung,exynos5410-pinctrl": for Exynos5410 compatible pin-controller.
+  - "samsung,exynos5420-pinctrl": for Exynos5420 compatible pin-controller.
+  - "samsung,exynos5433-pinctrl": for Exynos5433 compatible pin-controller.
+  - "samsung,exynos7-pinctrl": for Exynos7 compatible pin-controller.
+
+- reg: Base address of the pin controller hardware module and length of
+  the address space it occupies.
+
+  - reg: Second base address of the pin controller if the specific registers
+  of the pin controller are separated into the different base address.
+
+	Eg: GPF[1-5] of Exynos5433 are separated into the two base address.
+	- First base address is for GPAx and GPF[1-5] external interrupt
+	  registers.
+	- Second base address is for GPF[1-5] pinctrl registers.
+
+	pinctrl_0: pinctrl@10580000 {
+		compatible = "samsung,exynos5433-pinctrl";
+		reg = <0x10580000 0x1a20>, <0x11090000 0x100>;
+
+		wakeup-interrupt-controller {
+			compatible = "samsung,exynos7-wakeup-eint";
+			interrupts = <0 16 0>;
+		};
+	};
+
+- Pin banks as child nodes: Pin banks of the controller are represented by child
+  nodes of the controller node. Bank name is taken from name of the node. Each
+  bank node must contain following properties:
+
+  - gpio-controller: identifies the node as a gpio controller and pin bank.
+  - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
+    binding is used, the amount of cells must be specified as 2. See the below
+    mentioned gpio binding representation for description of particular cells.
+
+	Eg: <&gpx2 6 0>
+	<[phandle of the gpio controller node]
+	[pin number within the gpio controller]
+	[flags]>
+
+	Values for gpio specifier:
+	- Pin number: is a value between 0 to 7.
+	- Flags: 0 - Active High
+		 1 - Active Low
+
+- Pin mux/config groups as child nodes: The pin mux (selecting pin function
+  mode) and pin config (pull up/down, driver strength) settings are represented
+  as child nodes of the pin-controller node. There should be at least one
+  child node and there is no limit on the count of these child nodes. It is
+  also possible for a child node to consist of several further child nodes
+  to allow grouping multiple pinctrl groups into one. The format of second
+  level child nodes is exactly the same as for first level ones and is
+  described below.
+
+  The child node should contain a list of pin(s) on which a particular pin
+  function selection or pin configuration (or both) have to applied. This
+  list of pins is specified using the property name "samsung,pins". There
+  should be at least one pin specified for this property and there is no upper
+  limit on the count of pins that can be specified. The pins are specified
+  using pin names which are derived from the hardware manual of the SoC. As
+  an example, the pins in GPA0 bank of the pin controller can be represented
+  as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case.
+  The format of the pin names should be (as per the hardware manual)
+  "[pin bank name]-[pin number within the bank]".
+
+  The pin function selection that should be applied on the pins listed in the
+  child node is specified using the "samsung,pin-function" property. The value
+  of this property that should be applied to each of the pins listed in the
+  "samsung,pins" property should be picked from the hardware manual of the SoC
+  for the specified pin group. This property is optional in the child node if
+  no specific function selection is desired for the pins listed in the child
+  node. The value of this property is used as-is to program the pin-controller
+  function selector register of the pin-bank.
+
+  The child node can also optionally specify one or more of the pin
+  configuration that should be applied on all the pins listed in the
+  "samsung,pins" property of the child node. The following pin configuration
+  properties are supported.
+
+  - samsung,pin-val: Initial value of pin output buffer.
+  - samsung,pin-pud: Pull up/down configuration.
+  - samsung,pin-drv: Drive strength configuration.
+  - samsung,pin-pud-pdn: Pull up/down configuration in power down mode.
+  - samsung,pin-drv-pdn: Drive strength configuration in power down mode.
+
+  The values specified by these config properties should be derived from the
+  hardware manual and these values are programmed as-is into the pin
+  pull up/down and driver strength register of the pin-controller.
+
+  Note: A child should include at least a pin function selection property or
+  pin configuration property (one or more) or both.
+
+  The client nodes that require a particular pin function selection and/or
+  pin configuration should use the bindings listed in the "pinctrl-bindings.txt"
+  file.
+
+External GPIO and Wakeup Interrupts:
+
+The controller supports two types of external interrupts over gpio. The first
+is the external gpio interrupt and second is the external wakeup interrupts.
+The difference between the two is that the external wakeup interrupts can be
+used as system wakeup events.
+
+A. External GPIO Interrupts: For supporting external gpio interrupts, the
+   following properties should be specified in the pin-controller device node.
+
+   - interrupts: interrupt specifier for the controller. The format and value of
+     the interrupt specifier depends on the interrupt parent for the controller.
+
+   In addition, following properties must be present in node of every bank
+   of pins supporting GPIO interrupts:
+
+   - interrupt-controller: identifies the controller node as interrupt-parent.
+   - #interrupt-cells: the value of this property should be 2.
+     - First Cell: represents the external gpio interrupt number local to the
+       external gpio interrupt space of the controller.
+     - Second Cell: flags to identify the type of the interrupt
+       - 1 = rising edge triggered
+       - 2 = falling edge triggered
+       - 3 = rising and falling edge triggered
+       - 4 = high level triggered
+       - 8 = low level triggered
+
+B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
+   child node representing the external wakeup interrupt controller should be
+   included in the pin-controller device node.
+
+   Only one pin-controller device node can include external wakeup interrupts
+   child node (in other words, only one External Wakeup Interrupts
+   pin-controller is supported).
+
+   This child node should include following properties:
+
+   - compatible: identifies the type of the external wakeup interrupt controller
+     The possible values are:
+     - samsung,s3c2410-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung S3C24xx SoCs except S3C2412 and S3C2413,
+     - samsung,s3c2412-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung S3C2412 and S3C2413 SoCs,
+     - samsung,s3c64xx-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung S3C64xx SoCs,
+     - samsung,s5pv210-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung S5Pv210 SoCs,
+     - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung Exynos4210 and S5PC110/S5PV210 SoCs.
+     - samsung,exynos7-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung Exynos7 SoC.
+   - interrupts: interrupt used by multiplexed wakeup interrupts.
+
+   In addition, following properties must be present in node of every bank
+   of pins supporting wake-up interrupts:
+
+   - interrupt-controller: identifies the node as interrupt-parent.
+   - #interrupt-cells: the value of this property should be 2
+     - First Cell: represents the external wakeup interrupt number local to
+       the external wakeup interrupt space of the controller.
+     - Second Cell: flags to identify the type of the interrupt
+       - 1 = rising edge triggered
+       - 2 = falling edge triggered
+       - 3 = rising and falling edge triggered
+       - 4 = high level triggered
+       - 8 = low level triggered
+
+   Node of every bank of pins supporting direct wake-up interrupts (without
+   multiplexing) must contain following properties:
+
+   - interrupts: interrupts of the interrupt parent which are used for external
+     wakeup interrupts from pins of the bank, must contain interrupts for all
+     pins of the bank.
+
+Aliases:
+
+All the pin controller nodes should be represented in the aliases node using
+the following format 'pinctrl{n}' where n is a unique number for the alias.
+
+Aliases for controllers compatible with "samsung,exynos7-pinctrl":
+- pinctrl0: pin controller of ALIVE block,
+- pinctrl1: pin controller of BUS0 block,
+- pinctrl2: pin controller of NFC block,
+- pinctrl3: pin controller of TOUCH block,
+- pinctrl4: pin controller of FF block,
+- pinctrl5: pin controller of ESE block,
+- pinctrl6: pin controller of FSYS0 block,
+- pinctrl7: pin controller of FSYS1 block,
+- pinctrl8: pin controller of BUS1 block,
+- pinctrl9: pin controller of AUDIO block,
+
+Example: A pin-controller node with pin banks:
+
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,exynos4210-pinctrl";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+
+		/* ... */
+
+		/* Pin bank without external interrupts */
+		gpy0: gpy0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		/* ... */
+
+		/* Pin bank with external GPIO or muxed wake-up interrupts */
+		gpj0: gpj0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		/* ... */
+
+		/* Pin bank with external direct wake-up interrupts */
+		gpx0: gpx0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+				     <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>;
+			#interrupt-cells = <2>;
+		};
+
+		/* ... */
+	};
+
+Example 1: A pin-controller node with pin groups.
+
+	#include <dt-bindings/pinctrl/samsung.h>
+
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,exynos4210-pinctrl";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+
+		/* ... */
+
+		uart0_data: uart0-data {
+			samsung,pins = "gpa0-0", "gpa0-1";
+			samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+			samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+			samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		};
+
+		uart0_fctl: uart0-fctl {
+			samsung,pins = "gpa0-2", "gpa0-3";
+			samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+			samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+			samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		};
+
+		uart1_data: uart1-data {
+			samsung,pins = "gpa0-4", "gpa0-5";
+			samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+			samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+			samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		};
+
+		uart1_fctl: uart1-fctl {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+			samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+			samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		};
+
+		i2c2_bus: i2c2-bus {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+			samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+			samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		};
+
+		sd4_bus8: sd4-bus-width8 {
+			part-1 {
+				samsung,pins = "gpk0-3", "gpk0-4",
+						"gpk0-5", "gpk0-6";
+				samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+				samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+				samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+			};
+			part-2 {
+				samsung,pins = "gpk1-3", "gpk1-4",
+						"gpk1-5", "gpk1-6";
+				samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+				samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+				samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+			};
+		};
+	};
+
+Example 2: A pin-controller node with external wakeup interrupt controller node.
+
+	pinctrl_1: pinctrl@11000000 {
+		compatible = "samsung,exynos4210-pinctrl";
+		reg = <0x11000000 0x1000>;
+		interrupts = <0 46 0>
+
+		/* ... */
+
+		wakeup-interrupt-controller {
+			compatible = "samsung,exynos4210-wakeup-eint";
+			interrupt-parent = <&gic>;
+			interrupts = <0 32 0>;
+		};
+	};
+
+Example 3: A uart client node that supports 'default' and 'flow-control' states.
+
+	uart@13800000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13800000 0x100>;
+		interrupts = <0 52 0>;
+		pinctrl-names = "default", "flow-control;
+		pinctrl-0 = <&uart0_data>;
+		pinctrl-1 = <&uart0_data &uart0_fctl>;
+	};
+
+Example 4: Set up the default pin state for uart controller.
+
+	static int s3c24xx_serial_probe(struct platform_device *pdev) {
+		struct pinctrl *pinctrl;
+
+		/* ... */
+
+		pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
+	}
+
+Example 5: A display port client node that supports 'default' pinctrl state
+	   and gpio binding.
+
+	display-port-controller {
+		/* ... */
+
+		samsung,hpd-gpio = <&gpx2 6 0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dp_hpd>;
+	};
+
+Example 6: Request the gpio for display port controller
+
+	static int exynos_dp_probe(struct platform_device *pdev)
+	{
+		int hpd_gpio, ret;
+		struct device *dev = &pdev->dev;
+		struct device_node *dp_node = dev->of_node;
+
+		/* ... */
+
+		hpd_gpio = of_get_named_gpio(dp_node, "samsung,hpd-gpio", 0);
+
+		/* ... */
+
+		ret = devm_gpio_request_one(&pdev->dev, hpd_gpio, GPIOF_IN,
+					    "hpd_gpio");
+		/* ... */
+	}