Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 121 insertions, 0 deletions

diff --git a/Documentation/openrisc/openrisc_port.rst b/Documentation/openrisc/openrisc_port.rst
new file mode 100644
index 000000000..657ac4af7
--- /dev/null
+++ b/Documentation/openrisc/openrisc_port.rst
@@ -0,0 +1,121 @@
+==============
+OpenRISC Linux
+==============
+
+This is a port of Linux to the OpenRISC class of microprocessors; the initial
+target architecture, specifically, is the 32-bit OpenRISC 1000 family (or1k).
+
+For information about OpenRISC processors and ongoing development:
+
+	=======		=============================
+	website		https://openrisc.io
+	email		openrisc@lists.librecores.org
+	=======		=============================
+
+---------------------------------------------------------------------
+
+Build instructions for OpenRISC toolchain and Linux
+===================================================
+
+In order to build and run Linux for OpenRISC, you'll need at least a basic
+toolchain and, perhaps, the architectural simulator.  Steps to get these bits
+in place are outlined here.
+
+1) Toolchain
+
+Toolchain binaries can be obtained from openrisc.io or our github releases page.
+Instructions for building the different toolchains can be found on openrisc.io
+or Stafford's toolchain build and release scripts.
+
+	==========	=================================================
+	binaries	https://github.com/openrisc/or1k-gcc/releases
+	toolchains	https://openrisc.io/software
+	building	https://github.com/stffrdhrn/or1k-toolchain-build
+	==========	=================================================
+
+2) Building
+
+Build the Linux kernel as usual::
+
+	make ARCH=openrisc CROSS_COMPILE="or1k-linux-" defconfig
+	make ARCH=openrisc CROSS_COMPILE="or1k-linux-"
+
+3) Running on FPGA (optional)
+
+The OpenRISC community typically uses FuseSoC to manage building and programming
+an SoC into an FPGA.  The below is an example of programming a De0 Nano
+development board with the OpenRISC SoC.  During the build FPGA RTL is code
+downloaded from the FuseSoC IP cores repository and built using the FPGA vendor
+tools.  Binaries are loaded onto the board with openocd.
+
+::
+
+	git clone https://github.com/olofk/fusesoc
+	cd fusesoc
+	sudo pip install -e .
+
+	fusesoc init
+	fusesoc build de0_nano
+	fusesoc pgm de0_nano
+
+	openocd -f interface/altera-usb-blaster.cfg \
+		-f board/or1k_generic.cfg
+
+	telnet localhost 4444
+	> init
+	> halt; load_image vmlinux ; reset
+
+4) Running on a Simulator (optional)
+
+QEMU is a processor emulator which we recommend for simulating the OpenRISC
+platform.  Please follow the OpenRISC instructions on the QEMU website to get
+Linux running on QEMU.  You can build QEMU yourself, but your Linux distribution
+likely provides binary packages to support OpenRISC.
+
+	=============	======================================================
+	qemu openrisc	https://wiki.qemu.org/Documentation/Platforms/OpenRISC
+	=============	======================================================
+
+---------------------------------------------------------------------
+
+Terminology
+===========
+
+In the code, the following particles are used on symbols to limit the scope
+to more or less specific processor implementations:
+
+========= =======================================
+openrisc: the OpenRISC class of processors
+or1k:     the OpenRISC 1000 family of processors
+or1200:   the OpenRISC 1200 processor
+========= =======================================
+
+---------------------------------------------------------------------
+
+History
+========
+
+18-11-2003	Matjaz Breskvar (phoenix@bsemi.com)
+	initial port of linux to OpenRISC/or32 architecture.
+        all the core stuff is implemented and seams usable.
+
+08-12-2003	Matjaz Breskvar (phoenix@bsemi.com)
+	complete change of TLB miss handling.
+	rewrite of exceptions handling.
+	fully functional sash-3.6 in default initrd.
+	a much improved version with changes all around.
+
+10-04-2004	Matjaz Breskvar (phoenix@bsemi.com)
+	alot of bugfixes all over.
+	ethernet support, functional http and telnet servers.
+	running many standard linux apps.
+
+26-06-2004	Matjaz Breskvar (phoenix@bsemi.com)
+	port to 2.6.x
+
+30-11-2004	Matjaz Breskvar (phoenix@bsemi.com)
+	lots of bugfixes and enhancments.
+	added opencores framebuffer driver.
+
+09-10-2010    Jonas Bonn (jonas@southpole.se)
+	major rewrite to bring up to par with upstream Linux 2.6.36