Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 236 insertions, 0 deletions

diff --git a/drivers/ata/pata_triflex.c b/drivers/ata/pata_triflex.c
new file mode 100644
index 000000000..2a4d38b98
--- /dev/null
+++ b/drivers/ata/pata_triflex.c
@@ -0,0 +1,236 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * pata_triflex.c 	- Compaq PATA for new ATA layer
+ *			  (C) 2005 Red Hat Inc
+ *			  Alan Cox <alan@lxorguk.ukuu.org.uk>
+ *
+ * based upon
+ *
+ * triflex.c
+ *
+ * IDE Chipset driver for the Compaq TriFlex IDE controller.
+ *
+ * Known to work with the Compaq Workstation 5x00 series.
+ *
+ * Copyright (C) 2002 Hewlett-Packard Development Group, L.P.
+ * Author: Torben Mathiasen <torben.mathiasen@hp.com>
+ *
+ * Loosely based on the piix & svwks drivers.
+ *
+ * Documentation:
+ *	Not publicly available.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_triflex"
+#define DRV_VERSION "0.2.8"
+
+/**
+ *	triflex_prereset		-	probe begin
+ *	@link: ATA link
+ *	@deadline: deadline jiffies for the operation
+ *
+ *	Set up cable type and use generic probe init
+ */
+
+static int triflex_prereset(struct ata_link *link, unsigned long deadline)
+{
+	static const struct pci_bits triflex_enable_bits[] = {
+		{ 0x80, 1, 0x01, 0x01 },
+		{ 0x80, 1, 0x02, 0x02 }
+	};
+
+	struct ata_port *ap = link->ap;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+	if (!pci_test_config_bits(pdev, &triflex_enable_bits[ap->port_no]))
+		return -ENOENT;
+
+	return ata_sff_prereset(link, deadline);
+}
+
+
+
+/**
+ *	triflex_load_timing		-	timing configuration
+ *	@ap: ATA interface
+ *	@adev: Device on the bus
+ *	@speed: speed to configure
+ *
+ *	The Triflex has one set of timings per device per channel. This
+ *	means we must do some switching. As the PIO and DMA timings don't
+ *	match we have to do some reloading unlike PIIX devices where tuning
+ *	tricks can avoid it.
+ */
+
+static void triflex_load_timing(struct ata_port *ap, struct ata_device *adev, int speed)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u32 timing = 0;
+	u32 triflex_timing, old_triflex_timing;
+	int channel_offset = ap->port_no ? 0x74: 0x70;
+	unsigned int is_slave	= (adev->devno != 0);
+
+
+	pci_read_config_dword(pdev, channel_offset, &old_triflex_timing);
+	triflex_timing = old_triflex_timing;
+
+	switch(speed)
+	{
+		case XFER_MW_DMA_2:
+			timing = 0x0103;break;
+		case XFER_MW_DMA_1:
+			timing = 0x0203;break;
+		case XFER_MW_DMA_0:
+			timing = 0x0808;break;
+		case XFER_SW_DMA_2:
+		case XFER_SW_DMA_1:
+		case XFER_SW_DMA_0:
+			timing = 0x0F0F;break;
+		case XFER_PIO_4:
+			timing = 0x0202;break;
+		case XFER_PIO_3:
+			timing = 0x0204;break;
+		case XFER_PIO_2:
+			timing = 0x0404;break;
+		case XFER_PIO_1:
+			timing = 0x0508;break;
+		case XFER_PIO_0:
+			timing = 0x0808;break;
+		default:
+			BUG();
+	}
+	triflex_timing &= ~ (0xFFFF << (16 * is_slave));
+	triflex_timing |= (timing << (16 * is_slave));
+
+	if (triflex_timing != old_triflex_timing)
+		pci_write_config_dword(pdev, channel_offset, triflex_timing);
+}
+
+/**
+ *	triflex_set_piomode	-	set initial PIO mode data
+ *	@ap: ATA interface
+ *	@adev: ATA device
+ *
+ *	Use the timing loader to set up the PIO mode. We have to do this
+ *	because DMA start/stop will only be called once DMA occurs. If there
+ *	has been no DMA then the PIO timings are still needed.
+ */
+static void triflex_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	triflex_load_timing(ap, adev, adev->pio_mode);
+}
+
+/**
+ *	triflex_dma_start	-	DMA start callback
+ *	@qc: Command in progress
+ *
+ *	Usually drivers set the DMA timing at the point the set_dmamode call
+ *	is made. Triflex however requires we load new timings on the
+ *	transition or keep matching PIO/DMA pairs (ie MWDMA2/PIO4 etc).
+ *	We load the DMA timings just before starting DMA and then restore
+ *	the PIO timing when the DMA is finished.
+ */
+
+static void triflex_bmdma_start(struct ata_queued_cmd *qc)
+{
+	triflex_load_timing(qc->ap, qc->dev, qc->dev->dma_mode);
+	ata_bmdma_start(qc);
+}
+
+/**
+ *	triflex_dma_stop	-	DMA stop callback
+ *	@ap: ATA interface
+ *	@adev: ATA device
+ *
+ *	We loaded new timings in dma_start, as a result we need to restore
+ *	the PIO timings in dma_stop so that the next command issue gets the
+ *	right clock values.
+ */
+
+static void triflex_bmdma_stop(struct ata_queued_cmd *qc)
+{
+	ata_bmdma_stop(qc);
+	triflex_load_timing(qc->ap, qc->dev, qc->dev->pio_mode);
+}
+
+static struct scsi_host_template triflex_sht = {
+	ATA_BMDMA_SHT(DRV_NAME),
+};
+
+static struct ata_port_operations triflex_port_ops = {
+	.inherits	= &ata_bmdma_port_ops,
+	.bmdma_start 	= triflex_bmdma_start,
+	.bmdma_stop	= triflex_bmdma_stop,
+	.cable_detect	= ata_cable_40wire,
+	.set_piomode	= triflex_set_piomode,
+	.prereset	= triflex_prereset,
+};
+
+static int triflex_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	static const struct ata_port_info info = {
+		.flags = ATA_FLAG_SLAVE_POSS,
+		.pio_mask = ATA_PIO4,
+		.mwdma_mask = ATA_MWDMA2,
+		.port_ops = &triflex_port_ops
+	};
+	const struct ata_port_info *ppi[] = { &info, NULL };
+
+	ata_print_version_once(&dev->dev, DRV_VERSION);
+
+	return ata_pci_bmdma_init_one(dev, ppi, &triflex_sht, NULL, 0);
+}
+
+static const struct pci_device_id triflex[] = {
+	{ PCI_VDEVICE(COMPAQ, PCI_DEVICE_ID_COMPAQ_TRIFLEX_IDE), },
+
+	{ },
+};
+
+#ifdef CONFIG_PM_SLEEP
+static int triflex_ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
+{
+	struct ata_host *host = pci_get_drvdata(pdev);
+	int rc = 0;
+
+	rc = ata_host_suspend(host, mesg);
+	if (rc)
+		return rc;
+
+	/*
+	 * We must not disable or powerdown the device.
+	 * APM bios refuses to suspend if IDE is not accessible.
+	 */
+	pci_save_state(pdev);
+
+	return 0;
+}
+
+#endif
+
+static struct pci_driver triflex_pci_driver = {
+	.name 		= DRV_NAME,
+	.id_table	= triflex,
+	.probe 		= triflex_init_one,
+	.remove		= ata_pci_remove_one,
+#ifdef CONFIG_PM_SLEEP
+	.suspend	= triflex_ata_pci_device_suspend,
+	.resume		= ata_pci_device_resume,
+#endif
+};
+
+module_pci_driver(triflex_pci_driver);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for Compaq Triflex");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, triflex);
+MODULE_VERSION(DRV_VERSION);