Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 285 insertions, 0 deletions

diff --git a/drivers/tty/serial/zs.h b/drivers/tty/serial/zs.h
new file mode 100644
index 000000000..26ef8eafa
--- /dev/null
+++ b/drivers/tty/serial/zs.h
@@ -0,0 +1,285 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * zs.h: Definitions for the DECstation Z85C30 serial driver.
+ *
+ * Adapted from drivers/sbus/char/sunserial.h by Paul Mackerras.
+ * Adapted from drivers/macintosh/macserial.h by Harald Koerfgen.
+ *
+ * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)
+ * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
+ * Copyright (C) 2004, 2005, 2007  Maciej W. Rozycki
+ */
+#ifndef _SERIAL_ZS_H
+#define _SERIAL_ZS_H
+
+#ifdef __KERNEL__
+
+#define ZS_NUM_REGS 16
+
+/*
+ * This is our internal structure for each serial port's state.
+ */
+struct zs_port {
+	struct zs_scc	*scc;			/* Containing SCC.  */
+	struct uart_port port;			/* Underlying UART.  */
+
+	int		clk_mode;		/* May be 1, 16, 32, or 64.  */
+
+	unsigned int	tty_break;		/* Set on BREAK condition.  */
+	int		tx_stopped;		/* Output is suspended.  */
+
+	unsigned int	mctrl;			/* State of modem lines.  */
+	u8		brk;			/* BREAK state from RR0.  */
+
+	u8		regs[ZS_NUM_REGS];	/* Channel write registers.  */
+};
+
+/*
+ * Per-SCC state for locking and the interrupt handler.
+ */
+struct zs_scc {
+	struct zs_port	zport[2];
+	spinlock_t	zlock;
+	atomic_t	irq_guard;
+	int		initialised;
+};
+
+#endif /* __KERNEL__ */
+
+/*
+ * Conversion routines to/from brg time constants from/to bits per second.
+ */
+#define ZS_BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
+#define ZS_BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
+
+/*
+ * The Zilog register set.
+ */
+
+/* Write Register 0 (Command) */
+#define R0		0	/* Register selects */
+#define R1		1
+#define R2		2
+#define R3		3
+#define R4		4
+#define R5		5
+#define R6		6
+#define R7		7
+#define R8		8
+#define R9		9
+#define R10		10
+#define R11		11
+#define R12		12
+#define R13		13
+#define R14		14
+#define R15		15
+
+#define NULLCODE	0	/* Null Code */
+#define POINT_HIGH	0x8	/* Select upper half of registers */
+#define RES_EXT_INT	0x10	/* Reset Ext. Status Interrupts */
+#define SEND_ABORT	0x18	/* HDLC Abort */
+#define RES_RxINT_FC	0x20	/* Reset RxINT on First Character */
+#define RES_Tx_P	0x28	/* Reset TxINT Pending */
+#define ERR_RES		0x30	/* Error Reset */
+#define RES_H_IUS	0x38	/* Reset highest IUS */
+
+#define RES_Rx_CRC	0x40	/* Reset Rx CRC Checker */
+#define RES_Tx_CRC	0x80	/* Reset Tx CRC Checker */
+#define RES_EOM_L	0xC0	/* Reset EOM latch */
+
+/* Write Register 1 (Tx/Rx/Ext Int Enable and WAIT/DMA Commands) */
+#define EXT_INT_ENAB	0x1	/* Ext Int Enable */
+#define TxINT_ENAB	0x2	/* Tx Int Enable */
+#define PAR_SPEC	0x4	/* Parity is special condition */
+
+#define RxINT_DISAB	0	/* Rx Int Disable */
+#define RxINT_FCERR	0x8	/* Rx Int on First Character Only or Error */
+#define RxINT_ALL	0x10	/* Int on all Rx Characters or error */
+#define RxINT_ERR	0x18	/* Int on error only */
+#define RxINT_MASK	0x18
+
+#define WT_RDY_RT	0x20	/* Wait/Ready on R/T */
+#define WT_FN_RDYFN	0x40	/* Wait/FN/Ready FN */
+#define WT_RDY_ENAB	0x80	/* Wait/Ready Enable */
+
+/* Write Register 2 (Interrupt Vector) */
+
+/* Write Register 3 (Receive Parameters and Control) */
+#define RxENABLE	0x1	/* Rx Enable */
+#define SYNC_L_INH	0x2	/* Sync Character Load Inhibit */
+#define ADD_SM		0x4	/* Address Search Mode (SDLC) */
+#define RxCRC_ENAB	0x8	/* Rx CRC Enable */
+#define ENT_HM		0x10	/* Enter Hunt Mode */
+#define AUTO_ENAB	0x20	/* Auto Enables */
+#define Rx5		0x0	/* Rx 5 Bits/Character */
+#define Rx7		0x40	/* Rx 7 Bits/Character */
+#define Rx6		0x80	/* Rx 6 Bits/Character */
+#define Rx8		0xc0	/* Rx 8 Bits/Character */
+#define RxNBITS_MASK	0xc0
+
+/* Write Register 4 (Transmit/Receive Miscellaneous Parameters and Modes) */
+#define PAR_ENA		0x1	/* Parity Enable */
+#define PAR_EVEN	0x2	/* Parity Even/Odd* */
+
+#define SYNC_ENAB	0	/* Sync Modes Enable */
+#define SB1		0x4	/* 1 stop bit/char */
+#define SB15		0x8	/* 1.5 stop bits/char */
+#define SB2		0xc	/* 2 stop bits/char */
+#define SB_MASK		0xc
+
+#define MONSYNC		0	/* 8 Bit Sync character */
+#define BISYNC		0x10	/* 16 bit sync character */
+#define SDLC		0x20	/* SDLC Mode (01111110 Sync Flag) */
+#define EXTSYNC		0x30	/* External Sync Mode */
+
+#define X1CLK		0x0	/* x1 clock mode */
+#define X16CLK		0x40	/* x16 clock mode */
+#define X32CLK		0x80	/* x32 clock mode */
+#define X64CLK		0xc0	/* x64 clock mode */
+#define XCLK_MASK	0xc0
+
+/* Write Register 5 (Transmit Parameters and Controls) */
+#define TxCRC_ENAB	0x1	/* Tx CRC Enable */
+#define RTS		0x2	/* RTS */
+#define SDLC_CRC	0x4	/* SDLC/CRC-16 */
+#define TxENAB		0x8	/* Tx Enable */
+#define SND_BRK		0x10	/* Send Break */
+#define Tx5		0x0	/* Tx 5 bits (or less)/character */
+#define Tx7		0x20	/* Tx 7 bits/character */
+#define Tx6		0x40	/* Tx 6 bits/character */
+#define Tx8		0x60	/* Tx 8 bits/character */
+#define TxNBITS_MASK	0x60
+#define DTR		0x80	/* DTR */
+
+/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
+
+/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
+
+/* Write Register 8 (Transmit Buffer) */
+
+/* Write Register 9 (Master Interrupt Control) */
+#define VIS		1	/* Vector Includes Status */
+#define NV		2	/* No Vector */
+#define DLC		4	/* Disable Lower Chain */
+#define MIE		8	/* Master Interrupt Enable */
+#define STATHI		0x10	/* Status high */
+#define SOFTACK		0x20	/* Software Interrupt Acknowledge */
+#define NORESET		0	/* No reset on write to R9 */
+#define CHRB		0x40	/* Reset channel B */
+#define CHRA		0x80	/* Reset channel A */
+#define FHWRES		0xc0	/* Force hardware reset */
+
+/* Write Register 10 (Miscellaneous Transmitter/Receiver Control Bits) */
+#define BIT6		1	/* 6 bit/8bit sync */
+#define LOOPMODE	2	/* SDLC Loop mode */
+#define ABUNDER		4	/* Abort/flag on SDLC xmit underrun */
+#define MARKIDLE	8	/* Mark/flag on idle */
+#define GAOP		0x10	/* Go active on poll */
+#define NRZ		0	/* NRZ mode */
+#define NRZI		0x20	/* NRZI mode */
+#define FM1		0x40	/* FM1 (transition = 1) */
+#define FM0		0x60	/* FM0 (transition = 0) */
+#define CRCPS		0x80	/* CRC Preset I/O */
+
+/* Write Register 11 (Clock Mode Control) */
+#define TRxCXT		0	/* TRxC = Xtal output */
+#define TRxCTC		1	/* TRxC = Transmit clock */
+#define TRxCBR		2	/* TRxC = BR Generator Output */
+#define TRxCDP		3	/* TRxC = DPLL output */
+#define TRxCOI		4	/* TRxC O/I */
+#define TCRTxCP		0	/* Transmit clock = RTxC pin */
+#define TCTRxCP		8	/* Transmit clock = TRxC pin */
+#define TCBR		0x10	/* Transmit clock = BR Generator output */
+#define TCDPLL		0x18	/* Transmit clock = DPLL output */
+#define RCRTxCP		0	/* Receive clock = RTxC pin */
+#define RCTRxCP		0x20	/* Receive clock = TRxC pin */
+#define RCBR		0x40	/* Receive clock = BR Generator output */
+#define RCDPLL		0x60	/* Receive clock = DPLL output */
+#define RTxCX		0x80	/* RTxC Xtal/No Xtal */
+
+/* Write Register 12 (Lower Byte of Baud Rate Generator Time Constant) */
+
+/* Write Register 13 (Upper Byte of Baud Rate Generator Time Constant) */
+
+/* Write Register 14 (Miscellaneous Control Bits) */
+#define BRENABL		1	/* Baud rate generator enable */
+#define BRSRC		2	/* Baud rate generator source */
+#define DTRREQ		4	/* DTR/Request function */
+#define AUTOECHO	8	/* Auto Echo */
+#define LOOPBAK		0x10	/* Local loopback */
+#define SEARCH		0x20	/* Enter search mode */
+#define RMC		0x40	/* Reset missing clock */
+#define DISDPLL		0x60	/* Disable DPLL */
+#define SSBR		0x80	/* Set DPLL source = BR generator */
+#define SSRTxC		0xa0	/* Set DPLL source = RTxC */
+#define SFMM		0xc0	/* Set FM mode */
+#define SNRZI		0xe0	/* Set NRZI mode */
+
+/* Write Register 15 (External/Status Interrupt Control) */
+#define WR7P_EN		1	/* WR7 Prime SDLC Feature Enable */
+#define ZCIE		2	/* Zero count IE */
+#define DCDIE		8	/* DCD IE */
+#define SYNCIE		0x10	/* Sync/hunt IE */
+#define CTSIE		0x20	/* CTS IE */
+#define TxUIE		0x40	/* Tx Underrun/EOM IE */
+#define BRKIE		0x80	/* Break/Abort IE */
+
+
+/* Read Register 0 (Transmit/Receive Buffer Status and External Status) */
+#define Rx_CH_AV	0x1	/* Rx Character Available */
+#define ZCOUNT		0x2	/* Zero count */
+#define Tx_BUF_EMP	0x4	/* Tx Buffer empty */
+#define DCD		0x8	/* DCD */
+#define SYNC_HUNT	0x10	/* Sync/hunt */
+#define CTS		0x20	/* CTS */
+#define TxEOM		0x40	/* Tx underrun */
+#define BRK_ABRT	0x80	/* Break/Abort */
+
+/* Read Register 1 (Special Receive Condition Status) */
+#define ALL_SNT		0x1	/* All sent */
+/* Residue Data for 8 Rx bits/char programmed */
+#define RES3		0x8	/* 0/3 */
+#define RES4		0x4	/* 0/4 */
+#define RES5		0xc	/* 0/5 */
+#define RES6		0x2	/* 0/6 */
+#define RES7		0xa	/* 0/7 */
+#define RES8		0x6	/* 0/8 */
+#define RES18		0xe	/* 1/8 */
+#define RES28		0x0	/* 2/8 */
+/* Special Rx Condition Interrupts */
+#define PAR_ERR		0x10	/* Parity Error */
+#define Rx_OVR		0x20	/* Rx Overrun Error */
+#define FRM_ERR		0x40	/* CRC/Framing Error */
+#define END_FR		0x80	/* End of Frame (SDLC) */
+
+/* Read Register 2 (Interrupt Vector (WR2) -- channel A).  */
+
+/* Read Register 2 (Modified Interrupt Vector -- channel B).  */
+
+/* Read Register 3 (Interrupt Pending Bits -- channel A only).  */
+#define CHBEXT		0x1	/* Channel B Ext/Stat IP */
+#define CHBTxIP		0x2	/* Channel B Tx IP */
+#define CHBRxIP		0x4	/* Channel B Rx IP */
+#define CHAEXT		0x8	/* Channel A Ext/Stat IP */
+#define CHATxIP		0x10	/* Channel A Tx IP */
+#define CHARxIP		0x20	/* Channel A Rx IP */
+
+/* Read Register 6 (SDLC FIFO Status and Byte Count LSB) */
+
+/* Read Register 7 (SDLC FIFO Status and Byte Count MSB) */
+
+/* Read Register 8 (Receive Data) */
+
+/* Read Register 10 (Miscellaneous Status Bits) */
+#define ONLOOP		2	/* On loop */
+#define LOOPSEND	0x10	/* Loop sending */
+#define CLK2MIS		0x40	/* Two clocks missing */
+#define CLK1MIS		0x80	/* One clock missing */
+
+/* Read Register 12 (Lower Byte of Baud Rate Generator Constant (WR12)) */
+
+/* Read Register 13 (Upper Byte of Baud Rate Generator Constant (WR13) */
+
+/* Read Register 15 (External/Status Interrupt Control (WR15)) */
+
+#endif /* _SERIAL_ZS_H */