diff options
Diffstat (limited to 'Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt | 177 |
1 files changed, 177 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt b/Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt new file mode 100644 index 000000000..e31511255 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt @@ -0,0 +1,177 @@ +Marvell Armada AP80x System Controller +====================================== + +The AP806/AP807 is one of the two core HW blocks of the Marvell Armada +7K/8K/931x SoCs. It contains system controllers, which provide several +registers giving access to numerous features: clocks, pin-muxing and +many other SoC configuration items. This DT binding allows to describe +these system controllers. + +For the top level node: + - compatible: must be: "syscon", "simple-mfd"; + - reg: register area of the AP80x system controller + +SYSTEM CONTROLLER 0 +=================== + +Clocks: +------- + + +The Device Tree node representing the AP806/AP807 system controller +provides a number of clocks: + + - 0: reference clock of CPU cluster 0 + - 1: reference clock of CPU cluster 1 + - 2: fixed PLL at 1200 Mhz + - 3: MSS clock, derived from the fixed PLL + +Required properties: + + - compatible: must be one of: + * "marvell,ap806-clock" + * "marvell,ap807-clock" + - #clock-cells: must be set to 1 + +Pinctrl: +-------- + +For common binding part and usage, refer to +Documentation/devicetree/bindings/pinctrl/marvell,mvebu-pinctrl.txt. + +Required properties: +- compatible must be "marvell,ap806-pinctrl", + +Available mpp pins/groups and functions: +Note: brackets (x) are not part of the mpp name for marvell,function and given +only for more detailed description in this document. + +name pins functions +================================================================================ +mpp0 0 gpio, sdio(clk), spi0(clk) +mpp1 1 gpio, sdio(cmd), spi0(miso) +mpp2 2 gpio, sdio(d0), spi0(mosi) +mpp3 3 gpio, sdio(d1), spi0(cs0n) +mpp4 4 gpio, sdio(d2), i2c0(sda) +mpp5 5 gpio, sdio(d3), i2c0(sdk) +mpp6 6 gpio, sdio(ds) +mpp7 7 gpio, sdio(d4), uart1(rxd) +mpp8 8 gpio, sdio(d5), uart1(txd) +mpp9 9 gpio, sdio(d6), spi0(cs1n) +mpp10 10 gpio, sdio(d7) +mpp11 11 gpio, uart0(txd) +mpp12 12 gpio, sdio(pw_off), sdio(hw_rst) +mpp13 13 gpio +mpp14 14 gpio +mpp15 15 gpio +mpp16 16 gpio +mpp17 17 gpio +mpp18 18 gpio +mpp19 19 gpio, uart0(rxd), sdio(pw_off) + +GPIO: +----- +For common binding part and usage, refer to +Documentation/devicetree/bindings/gpio/gpio-mvebu.txt. + +Required properties: + +- compatible: "marvell,armada-8k-gpio" + +- offset: offset address inside the syscon block + +Example: +ap_syscon: system-controller@6f4000 { + compatible = "syscon", "simple-mfd"; + reg = <0x6f4000 0x1000>; + + ap_clk: clock { + compatible = "marvell,ap806-clock"; + #clock-cells = <1>; + }; + + ap_pinctrl: pinctrl { + compatible = "marvell,ap806-pinctrl"; + }; + + ap_gpio: gpio { + compatible = "marvell,armada-8k-gpio"; + offset = <0x1040>; + ngpios = <19>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&ap_pinctrl 0 0 19>; + }; +}; + +SYSTEM CONTROLLER 1 +=================== + +Thermal: +-------- + +For common binding part and usage, refer to +Documentation/devicetree/bindings/thermal/thermal*.yaml + +The thermal IP can probe the temperature all around the processor. It +may feature several channels, each of them wired to one sensor. + +It is possible to setup an overheat interrupt by giving at least one +critical point to any subnode of the thermal-zone node. + +Required properties: +- compatible: must be one of: + * marvell,armada-ap806-thermal +- reg: register range associated with the thermal functions. + +Optional properties: +- interrupts: overheat interrupt handle. Should point to line 18 of the + SEI irqchip. See interrupt-controller/interrupts.txt +- #thermal-sensor-cells: shall be <1> when thermal-zones subnodes refer + to this IP and represents the channel ID. There is one sensor per + channel. O refers to the thermal IP internal channel, while positive + IDs refer to each CPU. + +Example: +ap_syscon1: system-controller@6f8000 { + compatible = "syscon", "simple-mfd"; + reg = <0x6f8000 0x1000>; + + ap_thermal: thermal-sensor@80 { + compatible = "marvell,armada-ap806-thermal"; + reg = <0x80 0x10>; + interrupt-parent = <&sei>; + interrupts = <18>; + #thermal-sensor-cells = <1>; + }; +}; + +Cluster clocks: +--------------- + +Device Tree Clock bindings for cluster clock of Marvell +AP806/AP807. Each cluster contain up to 2 CPUs running at the same +frequency. + +Required properties: + - compatible: must be one of: + * "marvell,ap806-cpu-clock" + * "marvell,ap807-cpu-clock" +- #clock-cells : should be set to 1. + +- clocks : shall be the input parent clock(s) phandle for the clock + (one per cluster) + +- reg: register range associated with the cluster clocks + +ap_syscon1: system-controller@6f8000 { + compatible = "marvell,armada-ap806-syscon1", "syscon", "simple-mfd"; + reg = <0x6f8000 0x1000>; + + cpu_clk: clock-cpu@278 { + compatible = "marvell,ap806-cpu-clock"; + clocks = <&ap_clk 0>, <&ap_clk 1>; + #clock-cells = <1>; + reg = <0x278 0xa30>; + }; +}; |