1 files changed, 106 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt
new file mode 100644
index 000000000..e47c7ccc5
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt
@@ -0,0 +1,106 @@
+Texas Instruments VPIF
+----------------------
+
+The TI Video Port InterFace (VPIF) is the primary component for video
+capture and display on the DA850/AM18x family of TI DaVinci/Sitara
+SoCs.
+
+TI Document reference: SPRUH82C, Chapter 35
+http://www.ti.com/lit/pdf/spruh82
+
+Required properties:
+- compatible: must be "ti,da850-vpif"
+- reg: physical base address and length of the registers set for the device;
+- interrupts: should contain IRQ line for the VPIF
+
+Video Capture:
+
+VPIF has a 16-bit parallel bus input, supporting 2 8-bit channels or a
+single 16-bit channel. It should contain one or two port child nodes
+with child 'endpoint' node. If there are two ports then port@0 must
+describe the input and port@1 output channels. Please refer to the
+bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example using 2 8-bit input channels, one of which is connected to an
+I2C-connected TVP5147 decoder:
+
+	vpif: vpif@217000 {
+		compatible = "ti,da850-vpif";
+		reg = <0x217000 0x1000>;
+		interrupts = <92>;
+
+		port@0 {
+			vpif_input_ch0: endpoint@0 {
+				reg = <0>;
+				bus-width = <8>;
+				remote-endpoint = <&composite_in>;
+			};
+
+			vpif_input_ch1: endpoint@1 {
+				reg = <1>;
+				bus-width = <8>;
+				data-shift = <8>;
+			};
+		};
+
+		port@1 {
+			vpif_output_ch0: endpoint {
+				bus-width = <8>;
+				remote-endpoint = <&composite_out>;
+			};
+		};
+	};
+
+[ ... ]
+
+&i2c0 {
+
+	tvp5147@5d {
+		compatible = "ti,tvp5147";
+		reg = <0x5d>;
+
+		port {
+			composite_in: endpoint {
+				hsync-active = <1>;
+				vsync-active = <1>;
+				pclk-sample = <0>;
+
+				/* VPIF channel 0 (lower 8-bits) */
+				remote-endpoint = <&vpif_input_ch0>;
+				bus-width = <8>;
+			};
+		};
+	};
+
+	adv7343@2a {
+		compatible = "adi,adv7343";
+		reg = <0x2a>;
+
+		port {
+			composite_out: endpoint {
+				adi,dac-enable = <1 1 1>;
+				adi,sd-dac-enable = <1>;
+
+				remote-endpoint = <&vpif_output_ch0>;
+				bus-width = <8>;
+			};
+		};
+	};
+};
+
+
+Alternatively, an example when the bus is configured as a single
+16-bit input (e.g. for raw-capture mode):
+
+	vpif: vpif@217000 {
+		compatible = "ti,da850-vpif";
+		reg = <0x217000 0x1000>;
+		interrupts = <92>;
+
+		port {
+			vpif_ch0: endpoint {
+				  bus-width = <16>;
+			};
+		};
+	};