diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/dsa/mt7530.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/net/dsa/mt7530.txt | 315 |
1 files changed, 315 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/mt7530.txt b/Documentation/devicetree/bindings/net/dsa/mt7530.txt new file mode 100644 index 000000000..560369efa --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/mt7530.txt @@ -0,0 +1,315 @@ +Mediatek MT7530 Ethernet switch +================================ + +Required properties: + +- compatible: may be compatible = "mediatek,mt7530" + or compatible = "mediatek,mt7621" + or compatible = "mediatek,mt7531" +- #address-cells: Must be 1. +- #size-cells: Must be 0. +- mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part + on multi-chip module belong to MT7623A has or the remotely standalone + chip as the function MT7623N reference board provided for. + +If compatible mediatek,mt7530 is set then the following properties are required + +- core-supply: Phandle to the regulator node necessary for the core power. +- io-supply: Phandle to the regulator node necessary for the I/O power. + See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt + for details for the regulator setup on these boards. + +If the property mediatek,mcm isn't defined, following property is required + +- reset-gpios: Should be a gpio specifier for a reset line. + +Else, following properties are required + +- resets : Phandle pointing to the system reset controller with + line index for the ethsys. +- reset-names : Should be set to "mcm". + +Required properties for the child nodes within ports container: + +- reg: Port address described must be 6 for CPU port and from 0 to 5 for + user ports. +- phy-mode: String, the following values are acceptable for port labeled + "cpu": + If compatible mediatek,mt7530 or mediatek,mt7621 is set, + must be either "trgmii" or "rgmii" + If compatible mediatek,mt7531 is set, + must be either "sgmii", "1000base-x" or "2500base-x" + +Port 5 of mt7530 and mt7621 switch is muxed between: +1. GMAC5: GMAC5 can interface with another external MAC or PHY. +2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC + of the SOC. Used in many setups where port 0/4 becomes the WAN port. + Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to + GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not + connected to external component! + +Port 5 modes/configurations: +1. Port 5 is disabled and isolated: An external phy can interface to the 2nd + GMAC of the SOC. + In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd + GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC! +2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC. + It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode + and RGMII delay. +3. Port 5 is muxed to GMAC5 and can interface to an external phy. + Port 5 becomes an extra switch port. + Only works on platform where external phy TX<->RX lines are swapped. + Like in the Ubiquiti ER-X-SFP. +4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port. + Currently a 2nd CPU port is not supported by DSA code. + +Depending on how the external PHY is wired: +1. normal: The PHY can only connect to 2nd GMAC but not to the switch +2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as + a ethernet port. But can't interface to the 2nd GMAC. + +Based on the DT the port 5 mode is configured. + +Driver tries to lookup the phy-handle of the 2nd GMAC of the master device. +When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2. +phy-mode must be set, see also example 2 below! + * mt7621: phy-mode = "rgmii-txid"; + * mt7623: phy-mode = "rgmii"; + +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional +required, optional properties and how the integrated switch subnodes must +be specified. + +Example: + + &mdio0 { + switch@0 { + compatible = "mediatek,mt7530"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + core-supply = <&mt6323_vpa_reg>; + io-supply = <&mt6323_vemc3v3_reg>; + reset-gpios = <&pio 33 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; + +Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4. + +ð { + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "rgmii-txid"; + phy-handle = <&phy4>; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + /* Internal phy */ + phy4: ethernet-phy@4 { + reg = <4>; + }; + + mt7530: switch@1f { + compatible = "mediatek,mt7621"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1f>; + pinctrl-names = "default"; + mediatek,mcm; + + resets = <&rstctrl 2>; + reset-names = "mcm"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + +/* Commented out. Port 4 is handled by 2nd GMAC. + port@4 { + reg = <4>; + label = "lan4"; + }; +*/ + + cpu_port0: port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; +}; + +Example 3: MT7621: Port 5 is connected to external PHY: Port 5 -> external PHY. + +ð { + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + /* External phy */ + ephy5: ethernet-phy@7 { + reg = <7>; + }; + + mt7530: switch@1f { + compatible = "mediatek,mt7621"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1f>; + pinctrl-names = "default"; + mediatek,mcm; + + resets = <&rstctrl 2>; + reset-names = "mcm"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan4"; + }; + + port@5 { + reg = <5>; + label = "lan5"; + phy-mode = "rgmii"; + phy-handle = <&ephy5>; + }; + + cpu_port0: port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; +}; |