diff options
Diffstat (limited to 'Documentation/devicetree/bindings/phy/phy-miphy28lp.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/phy/phy-miphy28lp.txt | 117 |
1 files changed, 117 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt new file mode 100644 index 000000000..89caa885d --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt @@ -0,0 +1,117 @@ +STMicroelectronics STi MIPHY28LP PHY binding +============================================ + +This binding describes a miphy device that is used to control PHY hardware +for SATA, PCIe or USB3. + +Required properties (controller (parent) node): +- compatible : Should be "st,miphy28lp-phy". +- st,syscfg : Should be a phandle of the system configuration register group + which contain the SATA, PCIe or USB3 mode setting bits. + +Required nodes : A sub-node is required for each channel the controller + provides. Address range information including the usual + 'reg' and 'reg-names' properties are used inside these + nodes to describe the controller's topology. These nodes + are translated by the driver's .xlate() function. + +Required properties (port (child) node): +- #phy-cells : Should be 1 (See second example) + Cell after port phandle is device type from: + - PHY_TYPE_SATA + - PHY_TYPE_PCI + - PHY_TYPE_USB3 +- reg : Address and length of the register set for the device. +- reg-names : The names of the register addresses corresponding to the registers + filled in "reg". It can also contain the offset of the system configuration + registers used as glue-logic to setup the device for SATA/PCIe or USB3 + devices. +- st,syscfg : Offset of the parent configuration register. +- resets : phandle to the parent reset controller. +- reset-names : Associated name must be "miphy-sw-rst". + +Optional properties (port (child) node): +- st,osc-rdy : to check the MIPHY0_OSC_RDY status in the glue-logic. This + is not available in all the MiPHY. For example, for STiH407, only the + MiPHY0 has this bit. +- st,osc-force-ext : to select the external oscillator. This can change from + different MiPHY inside the same SoC. +- st,sata_gen : to select which SATA_SPDMODE has to be set in the SATA system config + register. +- st,px_rx_pol_inv : to invert polarity of RXn/RXp (respectively negative line and positive + line). +- st,scc-on : enable ssc to reduce effects of EMI (only for sata or PCIe). +- st,tx-impedance-comp : to compensate tx impedance avoiding out of range values. + +example: + + miphy28lp_phy: miphy28lp@9b22000 { + compatible = "st,miphy28lp-phy"; + st,syscfg = <&syscfg_core>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + phy_port0: port@9b22000 { + reg = <0x9b22000 0xff>, + <0x9b09000 0xff>, + <0x9b04000 0xff>; + reg-names = "sata-up", + "pcie-up", + "pipew"; + + st,syscfg = <0x114 0x818 0xe0 0xec>; + #phy-cells = <1>; + st,osc-rdy; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY0_SOFTRESET>; + }; + + phy_port1: port@9b2a000 { + reg = <0x9b2a000 0xff>, + <0x9b19000 0xff>, + <0x9b14000 0xff>; + reg-names = "sata-up", + "pcie-up", + "pipew"; + + st,syscfg = <0x118 0x81c 0xe4 0xf0>; + + #phy-cells = <1>; + st,osc-force-ext; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY1_SOFTRESET>; + }; + + phy_port2: port@8f95000 { + reg = <0x8f95000 0xff>, + <0x8f90000 0xff>; + reg-names = "pipew", + "usb3-up"; + + st,syscfg = <0x11c 0x820>; + + #phy-cells = <1>; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY2_SOFTRESET>; + }; + }; + + +Specifying phy control of devices +================================= + +Device nodes should specify the configuration required in their "phys" +property, containing a phandle to the miphy device node and an index +specifying which configuration to use, as described in phy-bindings.txt. + +example: + sata0: sata@9b20000 { + ... + phys = <&phy_port0 PHY_TYPE_SATA>; + ... + }; + +Macro definitions for the supported miphy configuration can be found in: + +include/dt-bindings/phy/phy.h |