diff options
Diffstat (limited to 'Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt | 109 |
1 files changed, 109 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt new file mode 100644 index 000000000..e7caefa0b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt @@ -0,0 +1,109 @@ +MediaTek XS-PHY binding +-------------------------- + +The XS-PHY controller supports physical layer functionality for USB3.1 +GEN2 controller on MediaTek SoCs. + +Required properties (controller (parent) node): + - compatible : should be "mediatek,<soc-model>-xsphy", "mediatek,xsphy", + soc-model is the name of SoC, such as mt3611 etc; + when using "mediatek,xsphy" compatible string, you need SoC specific + ones in addition, one of: + - "mediatek,mt3611-xsphy" + + - #address-cells, #size-cells : should use the same values as the root node + - ranges: must be present + +Optional properties (controller (parent) node): + - reg : offset and length of register shared by multiple U3 ports, + exclude port's private register, if only U2 ports provided, + shouldn't use the property. + - mediatek,src-ref-clk-mhz : u32, frequency of reference clock for slew rate + calibrate + - mediatek,src-coef : u32, coefficient for slew rate calibrate, depends on + SoC process + +Required nodes : a sub-node is required for each port the controller + provides. Address range information including the usual + 'reg' property is used inside these nodes to describe + the controller's topology. + +Required properties (port (child) node): +- reg : address and length of the register set for the port. +- clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names +- clock-names : must contain + "ref": 48M reference clock for HighSpeed analog phy; and 26M + reference clock for SuperSpeedPlus analog phy, sometimes is + 24M, 25M or 27M, depended on platform. +- #phy-cells : should be 1 + cell after port phandle is phy type from: + - PHY_TYPE_USB2 + - PHY_TYPE_USB3 + +The following optional properties are only for debug or HQA test +Optional properties (PHY_TYPE_USB2 port (child) node): +- mediatek,eye-src : u32, the value of slew rate calibrate +- mediatek,eye-vrt : u32, the selection of VRT reference voltage +- mediatek,eye-term : u32, the selection of HS_TX TERM reference voltage +- mediatek,efuse-intr : u32, the selection of Internal Resistor + +Optional properties (PHY_TYPE_USB3 port (child) node): +- mediatek,efuse-intr : u32, the selection of Internal Resistor +- mediatek,efuse-tx-imp : u32, the selection of TX Impedance +- mediatek,efuse-rx-imp : u32, the selection of RX Impedance + +Banks layout of xsphy +------------------------------------------------------------- +port offset bank +u2 port0 0x0000 MISC + 0x0100 FMREG + 0x0300 U2PHY_COM +u2 port1 0x1000 MISC + 0x1100 FMREG + 0x1300 U2PHY_COM +u2 port2 0x2000 MISC + ... +u31 common 0x3000 DIG_GLB + 0x3100 PHYA_GLB +u31 port0 0x3400 DIG_LN_TOP + 0x3500 DIG_LN_TX0 + 0x3600 DIG_LN_RX0 + 0x3700 DIG_LN_DAIF + 0x3800 PHYA_LN +u31 port1 0x3a00 DIG_LN_TOP + 0x3b00 DIG_LN_TX0 + 0x3c00 DIG_LN_RX0 + 0x3d00 DIG_LN_DAIF + 0x3e00 PHYA_LN + ... + +DIG_GLB & PHYA_GLB are shared by U31 ports. + +Example: + +u3phy: usb-phy@11c40000 { + compatible = "mediatek,mt3611-xsphy", "mediatek,xsphy"; + reg = <0 0x11c43000 0 0x0200>; + mediatek,src-ref-clk-mhz = <26>; + mediatek,src-coef = <17>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + u2port0: usb-phy@11c40000 { + reg = <0 0x11c40000 0 0x0400>; + clocks = <&clk48m>; + clock-names = "ref"; + mediatek,eye-src = <4>; + #phy-cells = <1>; + }; + + u3port0: usb-phy@11c43000 { + reg = <0 0x11c43400 0 0x0500>; + clocks = <&clk26m>; + clock-names = "ref"; + mediatek,efuse-intr = <28>; + #phy-cells = <1>; + }; +}; |