diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt | 185 |
1 files changed, 185 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt new file mode 100644 index 000000000..448d36a85 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt @@ -0,0 +1,185 @@ +Qualcomm PMIC Multi-Purpose Pin (MPP) block + +This binding describes the MPP block(s) found in the 8xxx series +of PMIC's from Qualcomm. + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain one of: + "qcom,pm8018-mpp", + "qcom,pm8038-mpp", + "qcom,pm8058-mpp", + "qcom,pm8821-mpp", + "qcom,pm8841-mpp", + "qcom,pm8916-mpp", + "qcom,pm8917-mpp", + "qcom,pm8921-mpp", + "qcom,pm8941-mpp", + "qcom,pm8950-mpp", + "qcom,pmi8950-mpp", + "qcom,pm8994-mpp", + "qcom,pma8084-mpp", + + And must contain either "qcom,spmi-mpp" or "qcom,ssbi-mpp" + if the device is on an spmi bus or an ssbi bus respectively. + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: Register base of the MPP block and length. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: Must contain an array of encoded interrupt specifiers for + each available MPP + +- gpio-controller: + Usage: required + Value type: <none> + Definition: Mark the device node as a GPIO controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: Must be 2; + the first cell will be used to define MPP number and the + second denotes the flags for this MPP + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin or a list of pins. This configuration can include the +mux function to select on those pin(s), and various pin configuration +parameters, as listed below. + +SUBNODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of MPP pins affected by the properties specified in + this subnode. Valid pins are: + mpp1-mpp4 for pm8841 + mpp1-mpp4 for pm8916 + mpp1-mpp8 for pm8941 + mpp1-mpp4 for pm8950 + mpp1-mpp4 for pmi8950 + mpp1-mpp4 for pma8084 + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Valid values are: + "digital", + "analog", + "sink" + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configured as no pull. + +- bias-pull-up: + Usage: optional + Value type: <u32> + Definition: The specified pins should be configured as pull up. + Valid values are 600, 10000 and 30000 in bidirectional mode + only, i.e. when operating in qcom,analog-mode and input and + outputs are enabled. The hardware ignores the configuration + when operating in other modes. + +- bias-high-impedance: + Usage: optional + Value type: <none> + Definition: The specified pins will put in high-Z mode and disabled. + +- input-enable: + Usage: optional + Value type: <none> + Definition: The specified pins are put in input mode, i.e. their input + buffer is enabled + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + +- power-source: + Usage: optional + Value type: <u32> + Definition: Selects the power source for the specified pins. Valid power + sources are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h> + +- qcom,analog-level: + Usage: optional + Value type: <u32> + Definition: Selects the source for analog output. Valued values are + defined in <dt-binding/pinctrl/qcom,pmic-mpp.h> + PMIC_MPP_AOUT_LVL_* + +- qcom,dtest: + Usage: optional + Value type: <u32> + Definition: Selects which dtest rail to be routed in the various functions. + Valid values are 1-4 + +- qcom,amux-route: + Usage: optional + Value type: <u32> + Definition: Selects the source for analog input. Valid values are + defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h> + PMIC_MPP_AMUX_ROUTE_CH5, PMIC_MPP_AMUX_ROUTE_CH6... +- qcom,paired: + Usage: optional + Value type: <none> + Definition: Indicates that the pin should be operating in paired mode. + +Example: + + mpps@a000 { + compatible = "qcom,pm8841-mpp", "qcom,spmi-mpp"; + reg = <0xa000>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <4 0xa0 0 0>, <4 0xa1 0 0>, <4 0xa2 0 0>, <4 0xa3 0 0>; + + pinctrl-names = "default"; + pinctrl-0 = <&pm8841_default>; + + pm8841_default: default { + gpio { + pins = "mpp1", "mpp2", "mpp3", "mpp4"; + function = "digital"; + input-enable; + power-source = <PM8841_MPP_S3>; + }; + }; + }; |