diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt | 121 |
1 files changed, 121 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt new file mode 100644 index 000000000..42d8814f9 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt @@ -0,0 +1,121 @@ +MT8173 xHCI + +The device node for Mediatek SOC USB3.0 host controller + +There are two scenarios: the first one only supports xHCI driver; +the second one supports dual-role mode, and the host is based on xHCI +driver. Take account of backward compatibility, we divide bindings +into two parts. + +1st: only supports xHCI driver +------------------------------------------------------------------------ + +Required properties: + - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci", + soc-model is the name of SoC, such as mt8173, mt2712 etc, when using + "mediatek,mtk-xhci" compatible string, you need SoC specific ones in + addition, one of: + - "mediatek,mt8173-xhci" + - reg : specifies physical base address and size of the registers + - reg-names: should be "mac" for xHCI MAC and "ippc" for IP port control + - interrupts : interrupt used by the controller + - power-domains : a phandle to USB power domain node to control USB's + mtcmos + - vusb33-supply : regulator of USB avdd3.3v + + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must contain + "sys_ck": controller clock used by normal mode, + the following ones are optional: + "ref_ck": reference clock used by low power mode etc, + "mcu_ck": mcu_bus clock for register access, + "dma_ck": dma_bus clock for data transfer by DMA, + "xhci_ck": controller clock + + - phys : see usb-hcd.yaml in the current directory + +Optional properties: + - wakeup-source : enable USB remote wakeup; + - mediatek,syscon-wakeup : phandle to syscon used to access the register + of the USB wakeup glue layer between xHCI and SPM; it depends on + "wakeup-source", and has two arguments: + - the first one : register base address of the glue layer in syscon; + - the second one : hardware version of the glue layer + - 1 : used by mt8173 etc + - 2 : used by mt2712 etc + - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0, + bit1 for u3port1, ... etc; + - vbus-supply : reference to the VBUS regulator; + - usb3-lpm-capable : supports USB3.0 LPM + - pinctrl-names : a pinctrl state named "default" must be defined + - pinctrl-0 : pin control group + See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + - imod-interval-ns: default interrupt moderation interval is 5000ns + +additionally the properties from usb-hcd.yaml (in the current directory) are +supported. + +Example: +usb30: usb@11270000 { + compatible = "mediatek,mt8173-xhci"; + reg = <0 0x11270000 0 0x1000>, + <0 0x11280700 0 0x0100>; + reg-names = "mac", "ippc"; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>, + <&pericfg CLK_PERI_USB0>, + <&pericfg CLK_PERI_USB1>; + clock-names = "sys_ck", "ref_ck"; + phys = <&phy_port0 PHY_TYPE_USB3>, + <&phy_port1 PHY_TYPE_USB2>; + vusb33-supply = <&mt6397_vusb_reg>; + vbus-supply = <&usb_p1_vbus>; + usb3-lpm-capable; + mediatek,syscon-wakeup = <&pericfg 0x400 1>; + wakeup-source; + imod-interval-ns = <10000>; +}; + +2nd: dual-role mode with xHCI driver +------------------------------------------------------------------------ + +In the case, xhci is added as subnode to mtu3. An example and the DT binding +details of mtu3 can be found in: +Documentation/devicetree/bindings/usb/mediatek,mtu3.txt + +Required properties: + - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci", + soc-model is the name of SoC, such as mt8173, mt2712 etc, when using + "mediatek,mtk-xhci" compatible string, you need SoC specific ones in + addition, one of: + - "mediatek,mt8173-xhci" + - reg : specifies physical base address and size of the registers + - reg-names: should be "mac" for xHCI MAC + - interrupts : interrupt used by the host controller + - power-domains : a phandle to USB power domain node to control USB's + mtcmos + - vusb33-supply : regulator of USB avdd3.3v + + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must contain "sys_ck", and the following ones are optional: + "ref_ck", "mcu_ck" and "dma_ck", "xhci_ck" + +Optional properties: + - vbus-supply : reference to the VBUS regulator; + - usb3-lpm-capable : supports USB3.0 LPM + +Example: +usb30: usb@11270000 { + compatible = "mediatek,mt8173-xhci"; + reg = <0 0x11270000 0 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; + clock-names = "sys_ck", "ref_ck"; + vusb33-supply = <&mt6397_vusb_reg>; + usb3-lpm-capable; +}; |