diff options
Diffstat (limited to 'Documentation/hwmon/ltc2947.rst')
| -rw-r--r-- | Documentation/hwmon/ltc2947.rst | 100 |
1 files changed, 100 insertions, 0 deletions
diff --git a/Documentation/hwmon/ltc2947.rst b/Documentation/hwmon/ltc2947.rst new file mode 100644 index 000000000..419fc84fe --- /dev/null +++ b/Documentation/hwmon/ltc2947.rst @@ -0,0 +1,100 @@ +Kernel drivers ltc2947-i2c and ltc2947-spi +========================================== + +Supported chips: + + * Analog Devices LTC2947 + + Prefix: 'ltc2947' + + Addresses scanned: - + + Datasheet: + + https://www.analog.com/media/en/technical-documentation/data-sheets/LTC2947.pdf + +Author: Nuno Sá <nuno.sa@analog.com> + +Description +___________ + +The LTC2947 is a high precision power and energy monitor that measures current, +voltage, power, temperature, charge and energy. The device supports both SPI +and I2C depending on the chip configuration. +The device also measures accumulated quantities as energy. It has two banks of +register's to read/set energy related values. These banks can be configured +independently to have setups like: energy1 accumulates always and enrgy2 only +accumulates if current is positive (to check battery charging efficiency for +example). The device also supports a GPIO pin that can be configured as output +to control a fan as a function of measured temperature. Then, the GPIO becomes +active as soon as a temperature reading is higher than a defined threshold. The +temp2 channel is used to control this thresholds and to read the respective +alarms. + +Sysfs entries +_____________ + +The following attributes are supported. Limits are read-write, reset_history +is write-only and all the other attributes are read-only. + +======================= ========================================== +in0_input VP-VM voltage (mV). +in0_min Undervoltage threshold +in0_max Overvoltage threshold +in0_lowest Lowest measured voltage +in0_highest Highest measured voltage +in0_reset_history Write 1 to reset in1 history +in0_min_alarm Undervoltage alarm +in0_max_alarm Overvoltage alarm +in0_label Channel label (VP-VM) + +in1_input DVCC voltage (mV) +in1_min Undervoltage threshold +in1_max Overvoltage threshold +in1_lowest Lowest measured voltage +in1_highest Highest measured voltage +in1_reset_history Write 1 to reset in2 history +in1_min_alarm Undervoltage alarm +in1_max_alarm Overvoltage alarm +in1_label Channel label (DVCC) + +curr1_input IP-IM Sense current (mA) +curr1_min Undercurrent threshold +curr1_max Overcurrent threshold +curr1_lowest Lowest measured current +curr1_highest Highest measured current +curr1_reset_history Write 1 to reset curr1 history +curr1_min_alarm Undercurrent alarm +curr1_max_alarm Overcurrent alarm +curr1_label Channel label (IP-IM) + +power1_input Power (in uW) +power1_min Low power threshold +power1_max High power threshold +power1_input_lowest Historical minimum power use +power1_input_highest Historical maximum power use +power1_reset_history Write 1 to reset power1 history +power1_min_alarm Low power alarm +power1_max_alarm High power alarm +power1_label Channel label (Power) + +temp1_input Chip Temperature (in milliC) +temp1_min Low temperature threshold +temp1_max High temperature threshold +temp1_input_lowest Historical minimum temperature use +temp1_input_highest Historical maximum temperature use +temp1_reset_history Write 1 to reset temp1 history +temp1_min_alarm Low temperature alarm +temp1_max_alarm High temperature alarm +temp1_label Channel label (Ambient) + +temp2_min Low temperature threshold for fan control +temp2_max High temperature threshold for fan control +temp2_min_alarm Low temperature fan control alarm +temp2_max_alarm High temperature fan control alarm +temp2_label Channel label (TEMPFAN) + +energy1_input Measured energy over time (in microJoule) + +energy2_input Measured energy over time (in microJoule) +======================= ========================================== |