diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/w1/w1-generic.rst | 133 |
1 files changed, 133 insertions, 0 deletions
diff --git a/Documentation/w1/w1-generic.rst b/Documentation/w1/w1-generic.rst new file mode 100644 index 000000000..da4e8b4e9 --- /dev/null +++ b/Documentation/w1/w1-generic.rst @@ -0,0 +1,133 @@ +========================================= +Introduction to the 1-wire (w1) subsystem +========================================= + +The 1-wire bus is a simple master-slave bus that communicates via a single +signal wire (plus ground, so two wires). + +Devices communicate on the bus by pulling the signal to ground via an open +drain output and by sampling the logic level of the signal line. + +The w1 subsystem provides the framework for managing w1 masters and +communication with slaves. + +All w1 slave devices must be connected to a w1 bus master device. + +Example w1 master devices: + + - DS9490 usb device + - W1-over-GPIO + - DS2482 (i2c to w1 bridge) + - Emulated devices, such as a RS232 converter, parallel port adapter, etc + + +What does the w1 subsystem do? +------------------------------ + +When a w1 master driver registers with the w1 subsystem, the following occurs: + + - sysfs entries for that w1 master are created + - the w1 bus is periodically searched for new slave devices + +When a device is found on the bus, w1 core tries to load the driver for its family +and check if it is loaded. If so, the family driver is attached to the slave. +If there is no driver for the family, default one is assigned, which allows to perform +almost any kind of operations. Each logical operation is a transaction +in nature, which can contain several (two or one) low-level operations. +Let's see how one can read EEPROM context: +1. one must write control buffer, i.e. buffer containing command byte +and two byte address. At this step bus is reset and appropriate device +is selected using either W1_SKIP_ROM or W1_MATCH_ROM command. +Then provided control buffer is being written to the wire. +2. reading. This will issue reading eeprom response. + +It is possible that between 1. and 2. w1 master thread will reset bus for searching +and slave device will be even removed, but in this case 0xff will +be read, since no device was selected. + + +W1 device families +------------------ + +Slave devices are handled by a driver written for a family of w1 devices. + +A family driver populates a struct w1_family_ops (see w1_family.h) and +registers with the w1 subsystem. + +Current family drivers: + +w1_therm + - (ds18?20 thermal sensor family driver) + provides temperature reading function which is bound to ->rbin() method + of the above w1_family_ops structure. + +w1_smem + - driver for simple 64bit memory cell provides ID reading method. + +You can call above methods by reading appropriate sysfs files. + + +What does a w1 master driver need to implement? +----------------------------------------------- + +The driver for w1 bus master must provide at minimum two functions. + +Emulated devices must provide the ability to set the output signal level +(write_bit) and sample the signal level (read_bit). + +Devices that support the 1-wire natively must provide the ability to write and +sample a bit (touch_bit) and reset the bus (reset_bus). + +Most hardware provides higher-level functions that offload w1 handling. +See struct w1_bus_master definition in w1.h for details. + + +w1 master sysfs interface +------------------------- + +========================= ===================================================== +<xx-xxxxxxxxxxxx> A directory for a found device. The format is + family-serial +bus (standard) symlink to the w1 bus +driver (standard) symlink to the w1 driver +w1_master_add (rw) manually register a slave device +w1_master_attempts (ro) the number of times a search was attempted +w1_master_max_slave_count (rw) maximum number of slaves to search for at a time +w1_master_name (ro) the name of the device (w1_bus_masterX) +w1_master_pullup (rw) 5V strong pullup 0 enabled, 1 disabled +w1_master_remove (rw) manually remove a slave device +w1_master_search (rw) the number of searches left to do, + -1=continual (default) +w1_master_slave_count (ro) the number of slaves found +w1_master_slaves (ro) the names of the slaves, one per line +w1_master_timeout (ro) the delay in seconds between searches +w1_master_timeout_us (ro) the delay in microseconds beetwen searches +========================= ===================================================== + +If you have a w1 bus that never changes (you don't add or remove devices), +you can set the module parameter search_count to a small positive number +for an initially small number of bus searches. Alternatively it could be +set to zero, then manually add the slave device serial numbers by +w1_master_add device file. The w1_master_add and w1_master_remove files +generally only make sense when searching is disabled, as a search will +redetect manually removed devices that are present and timeout manually +added devices that aren't on the bus. + +Bus searches occur at an interval, specified as a summ of timeout and +timeout_us module parameters (either of which may be 0) for as long as +w1_master_search remains greater than 0 or is -1. Each search attempt +decrements w1_master_search by 1 (down to 0) and increments +w1_master_attempts by 1. + +w1 slave sysfs interface +------------------------ + +=================== ============================================================ +bus (standard) symlink to the w1 bus +driver (standard) symlink to the w1 driver +name the device name, usually the same as the directory name +w1_slave (optional) a binary file whose meaning depends on the + family driver +rw (optional) created for slave devices which do not have + appropriate family driver. Allows to read/write binary data. +=================== ============================================================ |