diff options
Diffstat (limited to '')
| -rw-r--r-- | arch/arm/boot/dts/armada-388-helios4.dts | 324 |
1 files changed, 324 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/armada-388-helios4.dts b/arch/arm/boot/dts/armada-388-helios4.dts new file mode 100644 index 000000000..a7ff774d7 --- /dev/null +++ b/arch/arm/boot/dts/armada-388-helios4.dts @@ -0,0 +1,324 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Device Tree file for Helios4 + * based on SolidRun Clearfog revision A1 rev 2.0 (88F6828) + * + * Copyright (C) 2017 Aditya Prayoga <aditya@kobol.io> + * + */ + +/dts-v1/; +#include "armada-388.dtsi" +#include "armada-38x-solidrun-microsom.dtsi" + +/ { + model = "Helios4"; + compatible = "kobol,helios4", "marvell,armada388", + "marvell,armada385", "marvell,armada380"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x80000000>; /* 2 GB */ + }; + + aliases { + /* So that mvebu u-boot can update the MAC addresses */ + ethernet1 = ð0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reg_12v: regulator-12v { + compatible = "regulator-fixed"; + regulator-name = "power_brick_12V"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + vin-supply = <®_12v>; + }; + + reg_5p0v_hdd: regulator-5v-hdd { + compatible = "regulator-fixed"; + regulator-name = "5V_HDD"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <®_12v>; + }; + + reg_5p0v_usb: regulator-5v-usb { + compatible = "regulator-fixed"; + regulator-name = "USB-PWR"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + enable-active-high; + gpio = <&expander0 6 GPIO_ACTIVE_HIGH>; + vin-supply = <®_12v>; + }; + + system-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&helios_system_led_pins>; + + status-led { + label = "helios4:green:status"; + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + default-state = "on"; + }; + + fault-led { + label = "helios4:red:fault"; + gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + }; + + io-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&helios_io_led_pins>; + + sata1-led { + label = "helios4:green:ata1"; + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; + linux,default-trigger = "ata1"; + default-state = "off"; + }; + sata2-led { + label = "helios4:green:ata2"; + gpios = <&gpio1 18 GPIO_ACTIVE_LOW>; + linux,default-trigger = "ata2"; + default-state = "off"; + }; + sata3-led { + label = "helios4:green:ata3"; + gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + linux,default-trigger = "ata3"; + default-state = "off"; + }; + sata4-led { + label = "helios4:green:ata4"; + gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; + linux,default-trigger = "ata4"; + default-state = "off"; + }; + usb-led { + label = "helios4:green:usb"; + gpios = <&gpio1 22 GPIO_ACTIVE_LOW>; + linux,default-trigger = "usb-host"; + default-state = "off"; + }; + }; + + fan1: j10-pwm { + compatible = "pwm-fan"; + pwms = <&gpio1 9 40000>; /* Target freq:25 kHz */ + pinctrl-names = "default"; + pinctrl-0 = <&helios_fan1_pins>; + }; + + fan2: j17-pwm { + compatible = "pwm-fan"; + pwms = <&gpio1 23 40000>; /* Target freq:25 kHz */ + pinctrl-names = "default"; + pinctrl-0 = <&helios_fan2_pins>; + }; + + usb2_phy: usb2-phy { + compatible = "usb-nop-xceiv"; + vbus-regulator = <®_5p0v_usb>; + }; + + usb3_phy: usb3-phy { + compatible = "usb-nop-xceiv"; + }; + + soc { + internal-regs { + i2c@11000 { + /* + * PCA9655 GPIO expander, up to 1MHz clock. + * 0-Board Revision bit 0 # + * 1-Board Revision bit 1 # + * 5-USB3 overcurrent + * 6-USB3 power + */ + expander0: gpio-expander@20 { + /* + * This is how it should be: + * compatible = "onnn,pca9655", + * "nxp,pca9555"; + * but you can't do this because of + * the way I2C works. + */ + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&pca0_pins>; + interrupt-parent = <&gpio0>; + interrupts = <23 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + + board_rev_bit_0 { + gpio-hog; + gpios = <0 GPIO_ACTIVE_LOW>; + input; + line-name = "board-rev-0"; + }; + board_rev_bit_1 { + gpio-hog; + gpios = <1 GPIO_ACTIVE_LOW>; + input; + line-name = "board-rev-1"; + }; + usb3_ilimit { + gpio-hog; + gpios = <5 GPIO_ACTIVE_HIGH>; + input; + line-name = "usb-overcurrent-status"; + }; + }; + + temp_sensor: temp@4c { + compatible = "ti,lm75"; + reg = <0x4c>; + vcc-supply = <®_3p3v>; + }; + }; + + i2c@11100 { + /* + * External I2C Bus for user peripheral + */ + clock-frequency = <400000>; + pinctrl-0 = <&helios_i2c1_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + sata@a8000 { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + sata0: sata-port@0 { + reg = <0>; + }; + + sata1: sata-port@1 { + reg = <1>; + }; + }; + + sata@e0000 { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + sata2: sata-port@0 { + reg = <0>; + }; + + sata3: sata-port@1 { + reg = <1>; + }; + }; + + spi@10680 { + pinctrl-0 = <&spi1_pins + µsom_spi1_cs_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + sdhci@d8000 { + bus-width = <4>; + cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + no-1-8-v; + pinctrl-0 = <&helios_sdhci_pins + &helios_sdhci_cd_pins>; + pinctrl-names = "default"; + status = "okay"; + vmmc = <®_3p3v>; + wp-inverted; + }; + + usb@58000 { + usb-phy = <&usb2_phy>; + status = "okay"; + }; + + usb3@f0000 { + status = "okay"; + }; + + usb3@f8000 { + status = "okay"; + }; + + pinctrl@18000 { + pca0_pins: pca0-pins { + marvell,pins = "mpp23"; + marvell,function = "gpio"; + }; + microsom_phy0_int_pins: microsom-phy0-int-pins { + marvell,pins = "mpp18"; + marvell,function = "gpio"; + }; + helios_i2c1_pins: i2c1-pins { + marvell,pins = "mpp26", "mpp27"; + marvell,function = "i2c1"; + }; + helios_sdhci_cd_pins: helios-sdhci-cd-pins { + marvell,pins = "mpp20"; + marvell,function = "gpio"; + }; + helios_sdhci_pins: helios-sdhci-pins { + marvell,pins = "mpp21", "mpp28", + "mpp37", "mpp38", + "mpp39", "mpp40"; + marvell,function = "sd0"; + }; + helios_system_led_pins: helios-system-led-pins { + marvell,pins = "mpp24", "mpp25"; + marvell,function = "gpio"; + }; + helios_io_led_pins: helios-io-led-pins { + marvell,pins = "mpp49", "mpp50", + "mpp52", "mpp53", + "mpp54"; + marvell,function = "gpio"; + }; + helios_fan1_pins: helios_fan1_pins { + marvell,pins = "mpp41", "mpp43"; + marvell,function = "gpio"; + }; + helios_fan2_pins: helios_fan2_pins { + marvell,pins = "mpp48", "mpp55"; + marvell,function = "gpio"; + }; + microsom_spi1_cs_pins: spi1-cs-pins { + marvell,pins = "mpp59"; + marvell,function = "spi1"; + }; + }; + }; + }; +}; |