diff options
Diffstat (limited to '')
| -rw-r--r-- | arch/arm/boot/dts/armada-xp-db.dts | 245 |
1 files changed, 245 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts new file mode 100644 index 000000000..5d04dc68c --- /dev/null +++ b/arch/arm/boot/dts/armada-xp-db.dts @@ -0,0 +1,245 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Device Tree file for Marvell Armada XP evaluation board + * (DB-78460-BP) + * + * Copyright (C) 2012-2014 Marvell + * + * Lior Amsalem <alior@marvell.com> + * Gregory CLEMENT <gregory.clement@free-electrons.com> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> + * + * + * Note: this Device Tree assumes that the bootloader has remapped the + * internal registers to 0xf1000000 (instead of the default + * 0xd0000000). The 0xf1000000 is the default used by the recent, + * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier + * boards were delivered with an older version of the bootloader that + * left internal registers mapped at 0xd0000000. If you are in this + * situation, you should either update your bootloader (preferred + * solution) or the below Device Tree should be adjusted. + */ + +/dts-v1/; +#include "armada-xp-mv78460.dtsi" + +/ { + model = "Marvell Armada XP Evaluation Board"; + compatible = "marvell,axp-db", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0 0x00000000 0 0x80000000>; /* 2 GB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 + MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000 + MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000 + MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000 + MBUS_ID(0x0c, 0x04) 0 0 0xf1200000 0x100000>; + + devbus-bootcs { + status = "okay"; + + /* Device Bus parameters are required */ + + /* Read parameters */ + devbus,bus-width = <16>; + devbus,turn-off-ps = <60000>; + devbus,badr-skew-ps = <0>; + devbus,acc-first-ps = <124000>; + devbus,acc-next-ps = <248000>; + devbus,rd-setup-ps = <0>; + devbus,rd-hold-ps = <0>; + + /* Write parameters */ + devbus,sync-enable = <0>; + devbus,wr-high-ps = <60000>; + devbus,wr-low-ps = <60000>; + devbus,ale-wr-ps = <60000>; + + /* NOR 16 MiB */ + nor@0 { + compatible = "cfi-flash"; + reg = <0 0x1000000>; + bank-width = <2>; + }; + }; + + internal-regs { + serial@12000 { + status = "okay"; + }; + serial@12100 { + status = "okay"; + }; + serial@12200 { + status = "okay"; + }; + serial@12300 { + status = "okay"; + }; + + sata@a0000 { + nr-ports = <2>; + status = "okay"; + }; + + ethernet@70000 { + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; + buffer-manager = <&bm>; + bm,pool-long = <0>; + }; + ethernet@74000 { + status = "okay"; + phy = <&phy1>; + phy-mode = "rgmii-id"; + buffer-manager = <&bm>; + bm,pool-long = <1>; + }; + ethernet@30000 { + status = "okay"; + phy = <&phy2>; + phy-mode = "sgmii"; + buffer-manager = <&bm>; + bm,pool-long = <2>; + }; + ethernet@34000 { + status = "okay"; + phy = <&phy3>; + phy-mode = "sgmii"; + buffer-manager = <&bm>; + bm,pool-long = <3>; + }; + + bm@c0000 { + status = "okay"; + }; + + mvsdio@d4000 { + pinctrl-0 = <&sdio_pins>; + pinctrl-names = "default"; + status = "okay"; + /* No CD or WP GPIOs */ + broken-cd; + }; + + usb@50000 { + status = "okay"; + }; + + usb@51000 { + status = "okay"; + }; + + usb@52000 { + status = "okay"; + }; + + nand-controller@d0000 { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + nand-on-flash-bbt; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x800000>; + }; + partition@800000 { + label = "Linux"; + reg = <0x800000 0x800000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; + }; + }; + }; + }; + }; + + bm-bppi { + status = "okay"; + }; + }; +}; + +&pciec { + status = "okay"; + + /* + * All 6 slots are physically present as + * standard PCIe slots on the board. + */ + pcie@1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + pcie@2,0 { + /* Port 0, Lane 1 */ + status = "okay"; + }; + pcie@3,0 { + /* Port 0, Lane 2 */ + status = "okay"; + }; + pcie@4,0 { + /* Port 0, Lane 3 */ + status = "okay"; + }; + pcie@9,0 { + /* Port 2, Lane 0 */ + status = "okay"; + }; + pcie@a,0 { + /* Port 3, Lane 0 */ + status = "okay"; + }; +}; + +&mdio { + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + + phy2: ethernet-phy@2 { + reg = <25>; + }; + + phy3: ethernet-phy@3 { + reg = <27>; + }; +}; + +&spi0 { + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p64", "jedec,spi-nor"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <20000000>; + }; +}; |