diff options
Diffstat (limited to 'arch/arm/boot/dts/armada-xp-linksys-mamba.dts')
| -rw-r--r-- | arch/arm/boot/dts/armada-xp-linksys-mamba.dts | 399 |
1 files changed, 399 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts new file mode 100644 index 000000000..8480a1691 --- /dev/null +++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts @@ -0,0 +1,399 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Device Tree file for the Linksys WRT1900AC (Mamba). + * + * Note: this board is shipped with a new generation boot loader that + * remaps internal registers at 0xf1000000. Therefore, if earlyprintk + * is used, the CONFIG_DEBUG_MVEBU_UART0_ALTERNATE option should be + * used. + * + * Copyright (C) 2014 Imre Kaloz <kaloz@openwrt.org> + * + * Based on armada-xp-axpwifiap.dts: + * + * Copyright (C) 2013 Marvell + * + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> + */ + +/dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include "armada-xp-mv78230.dtsi" + +/ { + model = "Linksys WRT1900AC"; + compatible = "linksys,mamba", "marvell,armadaxp-mv78230", + "marvell,armadaxp", "marvell,armada-370-xp"; + + chosen { + bootargs = "console=ttyS0,115200"; + stdout-path = &uart0; + }; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x00000000 0x00000000 0x10000000>; /* 256MB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000 + MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000 + MBUS_ID(0x0c, 0x04) 0 0 0xf1200000 0x100000>; + + internal-regs { + + rtc@10300 { + /* No crystal connected to the internal RTC */ + status = "disabled"; + }; + + /* J10: VCC, NC, RX, NC, TX, GND */ + serial@12000 { + status = "okay"; + }; + + sata@a0000 { + nr-ports = <1>; + status = "okay"; + }; + + ethernet@70000 { + pinctrl-0 = <&ge0_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy-mode = "rgmii-id"; + buffer-manager = <&bm>; + bm,pool-long = <0>; + bm,pool-short = <1>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + ethernet@74000 { + pinctrl-0 = <&ge1_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy-mode = "rgmii-id"; + buffer-manager = <&bm>; + bm,pool-long = <2>; + bm,pool-short = <3>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + /* USB part of the eSATA/USB 2.0 port */ + usb@50000 { + status = "okay"; + }; + + i2c@11000 { + status = "okay"; + clock-frequency = <100000>; + + tmp421@4c { + compatible = "ti,tmp421"; + reg = <0x4c>; + }; + + tlc59116@68 { + #address-cells = <1>; + #size-cells = <0>; + #gpio-cells = <2>; + compatible = "ti,tlc59116"; + reg = <0x68>; + + wan_amber@0 { + label = "mamba:amber:wan"; + reg = <0x0>; + }; + + wan_white@1 { + label = "mamba:white:wan"; + reg = <0x1>; + }; + + wlan_2g@2 { + label = "mamba:white:wlan_2g"; + reg = <0x2>; + }; + + wlan_5g@3 { + label = "mamba:white:wlan_5g"; + reg = <0x3>; + }; + + esata@4 { + label = "mamba:white:esata"; + reg = <0x4>; + linux,default-trigger = "disk-activity"; + }; + + usb2@5 { + label = "mamba:white:usb2"; + reg = <0x5>; + }; + + usb3_1@6 { + label = "mamba:white:usb3_1"; + reg = <0x6>; + }; + + usb3_2@7 { + label = "mamba:white:usb3_2"; + reg = <0x7>; + }; + + wps_white@8 { + label = "mamba:white:wps"; + reg = <0x8>; + }; + + wps_amber@9 { + label = "mamba:amber:wps"; + reg = <0x9>; + }; + }; + }; + + bm@c8000 { + status = "okay"; + }; + }; + + bm-bppi { + status = "okay"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&keys_pin>; + pinctrl-names = "default"; + + wps { + label = "WPS"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; + }; + + reset { + label = "Factory Reset Button"; + linux,code = <KEY_RESTART>; + gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&power_led_pin>; + pinctrl-names = "default"; + + power { + label = "mamba:white:power"; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + pwm_fan { + /* SUNON HA4010V4-0000-C99 */ + + compatible = "pwm-fan"; + pwms = <&gpio0 24 4000>; + }; +}; + +&pciec { + status = "okay"; + + /* Etron EJ168 USB 3.0 controller */ + pcie@1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + + /* First mini-PCIe port */ + pcie@2,0 { + /* Port 0, Lane 1 */ + status = "okay"; + }; + + /* Second mini-PCIe port */ + pcie@3,0 { + /* Port 0, Lane 3 */ + status = "okay"; + }; +}; + +&pinctrl { + + keys_pin: keys-pin { + marvell,pins = "mpp32", "mpp33"; + marvell,function = "gpio"; + }; + + power_led_pin: power-led-pin { + marvell,pins = "mpp40"; + marvell,function = "gpio"; + }; + + gpio_fan_pin: gpio-fan-pin { + marvell,pins = "mpp24"; + marvell,function = "gpio"; + }; +}; + +&spi0 { + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "everspin,mr25h256"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <40000000>; + }; +}; + +&mdio { + status = "okay"; + + switch@0 { + compatible = "marvell,mv88e6085"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan4"; + }; + + port@1 { + reg = <1>; + label = "lan3"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan1"; + }; + + port@4 { + reg = <4>; + label = "internet"; + }; + + port@5 { + reg = <5>; + label = "cpu"; + ethernet = <ð0>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; +}; + +&nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; /* 1MB */ + read-only; + }; + + partition@100000 { + label = "u_env"; + reg = <0x100000 0x40000>; /* 256KB */ + }; + + partition@140000 { + label = "s_env"; + reg = <0x140000 0x40000>; /* 256KB */ + }; + + partition@900000 { + label = "devinfo"; + reg = <0x900000 0x100000>; /* 1MB */ + read-only; + }; + + /* kernel1 overlaps with rootfs1 by design */ + partition@a00000 { + label = "kernel1"; + reg = <0xa00000 0x2800000>; /* 40MB */ + }; + + partition@d00000 { + label = "rootfs1"; + reg = <0xd00000 0x2500000>; /* 37MB */ + }; + + /* kernel2 overlaps with rootfs2 by design */ + partition@3200000 { + label = "kernel2"; + reg = <0x3200000 0x2800000>; /* 40MB */ + }; + + partition@3500000 { + label = "rootfs2"; + reg = <0x3500000 0x2500000>; /* 37MB */ + }; + + /* + * 38MB, last MB is for the BBT, not writable + */ + partition@5a00000 { + label = "syscfg"; + reg = <0x5a00000 0x2600000>; + }; + + /* + * Unused area between "s_env" and "devinfo". + * Moved here because otherwise the renumbered + * partitions would break the bootloader + * supplied bootargs + */ + partition@180000 { + label = "unused_area"; + reg = <0x180000 0x780000>; /* 7.5MB */ + }; + }; + }; +}; |