diff options
Diffstat (limited to 'arch/arm/boot/dts/ste-ux500-samsung-golden.dts')
| -rw-r--r-- | arch/arm/boot/dts/ste-ux500-samsung-golden.dts | 657 |
1 files changed, 657 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-golden.dts b/arch/arm/boot/dts/ste-ux500-samsung-golden.dts new file mode 100644 index 000000000..aed1f2d5f --- /dev/null +++ b/arch/arm/boot/dts/ste-ux500-samsung-golden.dts @@ -0,0 +1,657 @@ +// SPDX-License-Identifier: GPL-2.0-only +/dts-v1/; + +#include "ste-db8500.dtsi" +#include "ste-ab8505.dtsi" +#include "ste-dbx5x0-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> + +/* + * Note: This device tree cannot be booted directly with the Samsung bootloader. + * You need an intermediate, device-tree compatible bootloader + * that locks the L2 cache. Otherwise the kernel will crash after decompression. + * + * There is a port of (mainline) U-Boot, see + * https://wiki.postmarketos.org/wiki/ST-Ericsson_NovaThor_U8500#U-Boot + */ +/ { + model = "Samsung Galaxy S III mini (GT-I8190)"; + compatible = "samsung,golden", "st-ericsson,u8500"; + + chosen { + stdout-path = &serial2; + }; + + i2c-gpio-0 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio2 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio2 13 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + + pinctrl-names = "default"; + pinctrl-0 = <&i2c_gpio_0_default>; + + #address-cells = <1>; + #size-cells = <0>; + + touchkey@20 { + compatible = "coreriver,tc360-touchkey"; + reg = <0x20>; + vdd-supply = <&ab8500_ldo_aux4_reg>; + vcc-supply = <&ab8500_ldo_aux6_reg>; + + interrupt-parent = <&gpio2>; + interrupts = <15 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default"; + pinctrl-0 = <&touchkey_default>; + linux,keycodes = <KEY_MENU KEY_BACK>; + }; + }; + + i2c-gpio-1 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + + pinctrl-names = "default"; + pinctrl-0 = <&i2c_gpio_1_default>; + + #address-cells = <1>; + #size-cells = <0>; + + magnetometer@c { + compatible = "alps,hscdtd008a"; + reg = <0x0c>; + + avdd-supply = <&ab8500_ldo_aux1_reg>; + dvdd-supply = <&ab8500_ldo_aux8_reg>; + }; + }; + + soc { + /* External Micro SD card slot */ + sdi0_per1@80126000 { + status = "okay"; + + arm,primecell-periphid = <0x10480180>; + max-frequency = <100000000>; + bus-width = <4>; + + non-removable; + /* + * Unfortunately, there is no way to enable the UHS + * modes due to a limitation of the SD level translator: + * It will either translate to 2.9V or disconnect the + * DATA lines, so switching to 1.8V signal voltage fails. + */ + cap-sd-highspeed; + cap-mmc-highspeed; + st,sig-pin-fbclk; + full-pwr-cycle; + + vmmc-supply = <&ab8500_ldo_aux3_reg>; + vqmmc-supply = <&sd_level_translator>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mc0_a_2_default>; + pinctrl-1 = <&mc0_a_2_sleep>; + }; + + /* WLAN SDIO */ + sdi1_per2@80118000 { + status = "okay"; + + arm,primecell-periphid = <0x10480180>; + max-frequency = <50000000>; + bus-width = <4>; + + non-removable; + cap-sd-highspeed; + + vmmc-supply = <&wl_reg_on>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mc1_a_2_default>; + pinctrl-1 = <&mc1_a_2_sleep>; + + #address-cells = <1>; + #size-cells = <0>; + + wifi@1 { + compatible = "brcm,bcm4329-fmac"; + reg = <1>; + + /* GPIO216 (WLAN_HOST_WAKE) */ + interrupt-parent = <&gpio6>; + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; + interrupt-names = "host-wake"; + + pinctrl-names = "default"; + pinctrl-0 = <&wlan_default>; + }; + }; + + /* eMMC */ + sdi2_per3@80005000 { + status = "okay"; + + arm,primecell-periphid = <0x10480180>; + max-frequency = <100000000>; + bus-width = <8>; + + non-removable; + cap-mmc-highspeed; + mmc-ddr-1_8v; + + vmmc-supply = <&vmem_3v3>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mc2_a_1_default>; + pinctrl-1 = <&mc2_a_1_sleep>; + }; + + /* BT UART */ + uart@80120000 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&u0_a_1_default>; + pinctrl-1 = <&u0_a_1_sleep>; + + bluetooth { + compatible = "brcm,bcm4330-bt"; + /* GPIO222 (BT_VREG_ON) */ + shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>; + /* GPIO199 (BT_WAKE) */ + device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; + /* GPIO97 (BT_HOST_WAKE) */ + host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&bluetooth_default>; + }; + }; + + /* GPF UART */ + uart@80121000 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>; + pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>; + }; + + /* Debugging console UART */ + uart@80007000 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&u2rxtx_c_1_default>; + pinctrl-1 = <&u2rxtx_c_1_sleep>; + }; + + i2c@80004000 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c0_a_1_default>; + pinctrl-1 = <&i2c0_a_1_sleep>; + + proximity@44 { + compatible = "sharp,gp2ap002s00f"; + reg = <0x44>; + + /* GPIO146 (PS_INT) */ + interrupt-parent = <&gpio4>; + interrupts = <18 IRQ_TYPE_EDGE_FALLING>; + + vdd-supply = <&ab8500_ldo_aux1_reg>; + vio-supply = <&ab8500_ldo_aux8_reg>; + + pinctrl-names = "default"; + pinctrl-0 = <&proximity_default>; + + sharp,proximity-far-hysteresis = <0x40>; + sharp,proximity-close-hysteresis = <0x0f>; + }; + }; + + i2c@80128000 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c2_b_2_default>; + pinctrl-1 = <&i2c2_b_2_sleep>; + + imu@68 { + compatible = "invensense,mpu6050"; + reg = <0x68>; + + /* GPIO206 (ACC_INT) */ + interrupt-parent = <&gpio6>; + interrupts = <14 IRQ_TYPE_EDGE_RISING>; + + mount-matrix = "0", "1", "0", + "-1", "0", "0", + "0", "0", "1"; + + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&ab8500_ldo_aux8_reg>; + + pinctrl-names = "default"; + pinctrl-0 = <&imu_default>; + }; + }; + + i2c@80110000 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c3_c_2_default>; + pinctrl-1 = <&i2c3_c_2_sleep>; + + touchscreen@4a { + compatible = "atmel,maxtouch"; + reg = <0x4a>; + + /* GPIO218 (TSP_INT_1V8) */ + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default"; + pinctrl-0 = <&tsp_default>; + }; + }; + + prcmu@80157000 { + ab8505 { + ab8500_usb { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&usb_a_1_default>; + pinctrl-1 = <&usb_a_1_sleep>; + }; + + ab8505-regulators { + ab8500_ldo_aux1 { + regulator-name = "sensor_3v"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ab8500_ldo_aux2 { + regulator-name = "vreg_tsp_a3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; /* FIXME */ + }; + + ab8500_ldo_aux3 { + regulator-name = "vdd_tf_2v91"; + }; + + ab8500_ldo_aux4 { + regulator-name = "key_led_3.3v"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ab8500_ldo_aux5 { + regulator-name = "vreg_tsp_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; /* FIXME */ + }; + + ab8500_ldo_aux6 { + regulator-name = "touch_key_2.2v"; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + }; + + ab8500_ldo_aux8 { + regulator-name = "sensor_1v8"; + }; + }; + }; + }; + + mcde@a0350000 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dsi_default_mode>; + + dsi-controller@a0351000 { + panel@0 { + compatible = "samsung,s6e63m0"; + reg = <0>; + max-brightness = <15>; + vdd3-supply = <&panel_reg_3v0>; + vci-supply = <&panel_reg_1v8>; + reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; + /* ESD (electrostatic discharge) detection interrupt */ + interrupt-parent = <&gpio2>; + interrupts = <18 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "esd"; + pinctrl-names = "default"; + pinctrl-0 = <&display_default_mode>; + }; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default>; + + label = "GPIO Buttons"; + + volume-up { + label = "Volume Up"; + /* GPIO67 (VOL_UP) */ + gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + + volume-down { + label = "Volume Down"; + /* GPIO92 (VOL_DOWN) */ + gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEDOWN>; + }; + + home { + label = "Home"; + /* GPIO91 (HOME_KEY) */ + gpios = <&gpio2 27 GPIO_ACTIVE_LOW>; + linux,code = <KEY_HOMEPAGE>; + }; + }; + + vibrator { + compatible = "gpio-vibrator"; + /* GPIO195 (MOT_EN) */ + enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&vibrator_default>; + }; + + /* External LDO for eMMC */ + vmem_3v3: regulator-vmem { + compatible = "regulator-fixed"; + + regulator-name = "vmem_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + + startup-delay-us = <200>; + + /* GPIO223 (MEM_LDO_EN) */ + gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&mem_ldo_default>; + }; + + /* TI TXS0206-29 level translator for 2.9 V */ + sd_level_translator: regulator-sd-level-translator { + compatible = "regulator-fixed"; + + regulator-name = "sd-level-translator"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + + startup-delay-us = <200>; + + /* GPIO87 (TXS0206-29_EN) */ + gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&sd_level_translator_default>; + }; + + /* + * WL_REG_ON takes WLAN out of reset and enables the internal regulators. + * The voltage specified here is only used to determine the OCR mask, + * the BCM chip is actually connected directly to VBAT. + */ + wl_reg_on: regulator-wl-reg-on { + compatible = "regulator-fixed"; + + regulator-name = "wl-reg-on"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + + startup-delay-us = <100000>; + + /* GPIO215 (WLAN_EN) */ + gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&wlan_en_default>; + }; + + /* MIC5366 GPIO-controlled regulator */ + panel_reg_1v8: regulator-panel-1v8 { + compatible = "regulator-fixed"; + + regulator-name = "panel-fixed-supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + /* GPIO219 */ + gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; + + startup-delay-us = <200>; + enable-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&panel_reg_default_mode>; + }; + + /* MIC5366 GPIO-controlled regulator */ + panel_reg_3v0: regulator-panel-3v0 { + compatible = "regulator-fixed"; + + regulator-name = "panel-fixed-supply"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + /* GPIO219 */ + gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; + + startup-delay-us = <200>; + enable-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&panel_reg_default_mode>; + }; +}; + +&pinctrl { + gpio-keys { + gpio_keys_default: gpio_keys_default { + golden_cfg1 { + pins = "GPIO67", /* VOL_UP */ + "GPIO91", /* HOME_KEY */ + "GPIO92"; /* VOL_DOWN */ + ste,config = <&gpio_in_pu>; + }; + }; + }; + + i2c-gpio-0 { + i2c_gpio_0_default: i2c_gpio_0 { + golden_cfg1 { + pins = "GPIO77", /* TOUCHKEY_SCL */ + "GPIO78"; /* TOUCHKEY_SDA */ + ste,config = <&gpio_in_nopull>; + }; + }; + }; + + i2c-gpio-1 { + i2c_gpio_1_default: i2c_gpio_1 { + golden_cfg1 { + pins = "GPIO151", /* COMP_SCL */ + "GPIO152"; /* COMP_SDA */ + ste,config = <&gpio_in_nopull>; + }; + }; + }; + + touchkey { + touchkey_default: touchkey_default { + golden_cfg1 { + pins = "GPIO79"; /* TOUCHKEY_INT */ + ste,config = <&gpio_in_nopull>; + }; + }; + }; + + sdi0 { + sd_level_translator_default: sd_level_translator_default { + golden_cfg1 { + pins = "GPIO87_B3"; /* TXS0206-29_EN */ + ste,config = <&gpio_out_lo>; + }; + }; + }; + + sdi2 { + mem_ldo_default: mem_ldo_default { + golden_cfg1 { + pins = "GPIO223_AH9"; /* MEM_LDO_EN */ + ste,config = <&gpio_out_hi>; + }; + }; + }; + + mcde { + dsi_default_mode: dsi_default { + default_mux1 { + /* Mux in VSI0 used for DSI TE */ + function = "lcd"; + groups = + "lcdvsi0_a_1"; /* VSI0 for LCD */ + }; + default_cfg1 { + pins = + "GPIO68_E1"; /* VSI0 */ + ste,config = <&in_nopull>; + }; + }; + }; + + display { + display_default_mode: display_default { + golden_cfg1 { + pins = "GPIO139_C9"; /* MIPI_DSI0_RESET_N */ + ste,config = <&gpio_out_lo>; + }; + golden_cfg2 { + pins = "GPIO82_C1"; /* LDI_ESD_DET */ + ste,config = <&gpio_in_pu>; + }; + }; + panel_reg_default_mode: panel_reg_default { + golden_cfg1 { + pins = "GPIO219_AG10"; /* LCD_PWR_EN */ + ste,config = <&gpio_out_lo>; + }; + }; + }; + + proximity { + proximity_default: proximity_default { + golden_cfg1 { + pins = "GPIO146_D13"; /* PS_INT */ + ste,config = <&gpio_in_nopull>; + }; + }; + }; + + imu { + imu_default: imu_default { + golden_cfg1 { + pins = "GPIO206_AG24"; /* ACC_INT */ + ste,config = <&gpio_in_pd>; + }; + }; + }; + + tsp { + tsp_default: tsp_default { + golden_cfg1 { + pins = "GPIO218_AH11"; /* TSP_INT_1V8 */ + ste,config = <&gpio_in_nopull>; + }; + }; + }; + + wlan { + wlan_default: wlan_default { + golden_cfg1 { + pins = "GPIO216_AG12"; /* WLAN_HOST_WAKE */ + ste,config = <&gpio_in_pd>; + }; + }; + + wlan_en_default: wlan_en_default { + golden_cfg1 { + pins = "GPIO215_AH13"; /* WLAN_EN */ + ste,config = <&gpio_out_lo>; + }; + }; + }; + + bluetooth { + bluetooth_default: bluetooth_default { + golden_cfg1 { + pins = "GPIO199_AH23", /* BT_WAKE */ + "GPIO222_AJ9"; /* BT_VREG_ON */ + ste,config = <&gpio_out_lo>; + }; + golden_cfg2 { + pins = "GPIO97_D9"; /* BT_HOST_WAKE */ + ste,config = <&gpio_in_nopull>; + }; + }; + }; + + vibrator { + vibrator_default: vibrator_default { + golden_cfg1 { + pins = "GPIO195_AG28"; /* MOT_EN */ + ste,config = <&gpio_out_lo>; + }; + }; + }; +}; + +&ab8505_gpio { + /* Hog a few default settings */ + pinctrl-names = "default"; + pinctrl-0 = <&gpio_default>; + + gpio { + gpio_default: gpio_default { + golden_mux { + /* Change unused pins to GPIO mode */ + function = "gpio"; + groups = "gpio3_a_1", /* default: SysClkReq4 */ + "gpio14_a_1"; /* default: PWMOut1 */ + }; + golden_cfg1 { + pins = "GPIO11_B17", "GPIO13_D17", "GPIO50_L4"; + bias-disable; + }; + }; + }; +}; |