diff options
Diffstat (limited to 'arch/mips/sibyte/bcm1480')
| -rw-r--r-- | arch/mips/sibyte/bcm1480/Makefile | 4 | ||||
| -rw-r--r-- | arch/mips/sibyte/bcm1480/irq.c | 348 | ||||
| -rw-r--r-- | arch/mips/sibyte/bcm1480/setup.c | 128 | ||||
| -rw-r--r-- | arch/mips/sibyte/bcm1480/smp.c | 179 | ||||
| -rw-r--r-- | arch/mips/sibyte/bcm1480/time.c | 14 |
5 files changed, 673 insertions, 0 deletions
diff --git a/arch/mips/sibyte/bcm1480/Makefile b/arch/mips/sibyte/bcm1480/Makefile new file mode 100644 index 000000000..cf1327d3f --- /dev/null +++ b/arch/mips/sibyte/bcm1480/Makefile @@ -0,0 +1,4 @@ +# SPDX-License-Identifier: GPL-2.0-only +obj-y := setup.o irq.o time.o + +obj-$(CONFIG_SMP) += smp.o diff --git a/arch/mips/sibyte/bcm1480/irq.c b/arch/mips/sibyte/bcm1480/irq.c new file mode 100644 index 000000000..7929bee91 --- /dev/null +++ b/arch/mips/sibyte/bcm1480/irq.c @@ -0,0 +1,348 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Copyright (C) 2000,2001,2002,2003,2004 Broadcom Corporation + */ +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/linkage.h> +#include <linux/interrupt.h> +#include <linux/smp.h> +#include <linux/spinlock.h> +#include <linux/mm.h> +#include <linux/kernel_stat.h> + +#include <asm/errno.h> +#include <asm/irq_regs.h> +#include <asm/signal.h> +#include <asm/io.h> + +#include <asm/sibyte/bcm1480_regs.h> +#include <asm/sibyte/bcm1480_int.h> +#include <asm/sibyte/bcm1480_scd.h> + +#include <asm/sibyte/sb1250_uart.h> +#include <asm/sibyte/sb1250.h> + +/* + * These are the routines that handle all the low level interrupt stuff. + * Actions handled here are: initialization of the interrupt map, requesting of + * interrupt lines by handlers, dispatching if interrupts to handlers, probing + * for interrupt lines + */ + +#ifdef CONFIG_PCI +extern unsigned long ht_eoi_space; +#endif + +/* Store the CPU id (not the logical number) */ +int bcm1480_irq_owner[BCM1480_NR_IRQS]; + +static DEFINE_RAW_SPINLOCK(bcm1480_imr_lock); + +void bcm1480_mask_irq(int cpu, int irq) +{ + unsigned long flags, hl_spacing; + u64 cur_ints; + + raw_spin_lock_irqsave(&bcm1480_imr_lock, flags); + hl_spacing = 0; + if ((irq >= BCM1480_NR_IRQS_HALF) && (irq <= BCM1480_NR_IRQS)) { + hl_spacing = BCM1480_IMR_HL_SPACING; + irq -= BCM1480_NR_IRQS_HALF; + } + cur_ints = ____raw_readq(IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing)); + cur_ints |= (((u64) 1) << irq); + ____raw_writeq(cur_ints, IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing)); + raw_spin_unlock_irqrestore(&bcm1480_imr_lock, flags); +} + +void bcm1480_unmask_irq(int cpu, int irq) +{ + unsigned long flags, hl_spacing; + u64 cur_ints; + + raw_spin_lock_irqsave(&bcm1480_imr_lock, flags); + hl_spacing = 0; + if ((irq >= BCM1480_NR_IRQS_HALF) && (irq <= BCM1480_NR_IRQS)) { + hl_spacing = BCM1480_IMR_HL_SPACING; + irq -= BCM1480_NR_IRQS_HALF; + } + cur_ints = ____raw_readq(IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing)); + cur_ints &= ~(((u64) 1) << irq); + ____raw_writeq(cur_ints, IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing)); + raw_spin_unlock_irqrestore(&bcm1480_imr_lock, flags); +} + +#ifdef CONFIG_SMP +static int bcm1480_set_affinity(struct irq_data *d, const struct cpumask *mask, + bool force) +{ + unsigned int irq_dirty, irq = d->irq; + int i = 0, old_cpu, cpu, int_on, k; + u64 cur_ints; + unsigned long flags; + + i = cpumask_first_and(mask, cpu_online_mask); + + /* Convert logical CPU to physical CPU */ + cpu = cpu_logical_map(i); + + /* Protect against other affinity changers and IMR manipulation */ + raw_spin_lock_irqsave(&bcm1480_imr_lock, flags); + + /* Swizzle each CPU's IMR (but leave the IP selection alone) */ + old_cpu = bcm1480_irq_owner[irq]; + irq_dirty = irq; + if ((irq_dirty >= BCM1480_NR_IRQS_HALF) && (irq_dirty <= BCM1480_NR_IRQS)) { + irq_dirty -= BCM1480_NR_IRQS_HALF; + } + + for (k=0; k<2; k++) { /* Loop through high and low interrupt mask register */ + cur_ints = ____raw_readq(IOADDR(A_BCM1480_IMR_MAPPER(old_cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + (k*BCM1480_IMR_HL_SPACING))); + int_on = !(cur_ints & (((u64) 1) << irq_dirty)); + if (int_on) { + /* If it was on, mask it */ + cur_ints |= (((u64) 1) << irq_dirty); + ____raw_writeq(cur_ints, IOADDR(A_BCM1480_IMR_MAPPER(old_cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + (k*BCM1480_IMR_HL_SPACING))); + } + bcm1480_irq_owner[irq] = cpu; + if (int_on) { + /* unmask for the new CPU */ + cur_ints = ____raw_readq(IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + (k*BCM1480_IMR_HL_SPACING))); + cur_ints &= ~(((u64) 1) << irq_dirty); + ____raw_writeq(cur_ints, IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + (k*BCM1480_IMR_HL_SPACING))); + } + } + raw_spin_unlock_irqrestore(&bcm1480_imr_lock, flags); + + return 0; +} +#endif + + +/*****************************************************************************/ + +static void disable_bcm1480_irq(struct irq_data *d) +{ + unsigned int irq = d->irq; + + bcm1480_mask_irq(bcm1480_irq_owner[irq], irq); +} + +static void enable_bcm1480_irq(struct irq_data *d) +{ + unsigned int irq = d->irq; + + bcm1480_unmask_irq(bcm1480_irq_owner[irq], irq); +} + + +static void ack_bcm1480_irq(struct irq_data *d) +{ + unsigned int irq_dirty, irq = d->irq; + u64 pending; + int k; + + /* + * If the interrupt was an HT interrupt, now is the time to + * clear it. NOTE: we assume the HT bridge was set up to + * deliver the interrupts to all CPUs (which makes affinity + * changing easier for us) + */ + irq_dirty = irq; + if ((irq_dirty >= BCM1480_NR_IRQS_HALF) && (irq_dirty <= BCM1480_NR_IRQS)) { + irq_dirty -= BCM1480_NR_IRQS_HALF; + } + for (k=0; k<2; k++) { /* Loop through high and low LDT interrupts */ + pending = __raw_readq(IOADDR(A_BCM1480_IMR_REGISTER(bcm1480_irq_owner[irq], + R_BCM1480_IMR_LDT_INTERRUPT_H + (k*BCM1480_IMR_HL_SPACING)))); + pending &= ((u64)1 << (irq_dirty)); + if (pending) { +#ifdef CONFIG_SMP + int i; + for (i=0; i<NR_CPUS; i++) { + /* + * Clear for all CPUs so an affinity switch + * doesn't find an old status + */ + __raw_writeq(pending, IOADDR(A_BCM1480_IMR_REGISTER(cpu_logical_map(i), + R_BCM1480_IMR_LDT_INTERRUPT_CLR_H + (k*BCM1480_IMR_HL_SPACING)))); + } +#else + __raw_writeq(pending, IOADDR(A_BCM1480_IMR_REGISTER(0, R_BCM1480_IMR_LDT_INTERRUPT_CLR_H + (k*BCM1480_IMR_HL_SPACING)))); +#endif + + /* + * Generate EOI. For Pass 1 parts, EOI is a nop. For + * Pass 2, the LDT world may be edge-triggered, but + * this EOI shouldn't hurt. If they are + * level-sensitive, the EOI is required. + */ +#ifdef CONFIG_PCI + if (ht_eoi_space) + *(uint32_t *)(ht_eoi_space+(irq<<16)+(7<<2)) = 0; +#endif + } + } + bcm1480_mask_irq(bcm1480_irq_owner[irq], irq); +} + +static struct irq_chip bcm1480_irq_type = { + .name = "BCM1480-IMR", + .irq_mask_ack = ack_bcm1480_irq, + .irq_mask = disable_bcm1480_irq, + .irq_unmask = enable_bcm1480_irq, +#ifdef CONFIG_SMP + .irq_set_affinity = bcm1480_set_affinity +#endif +}; + +void __init init_bcm1480_irqs(void) +{ + int i; + + for (i = 0; i < BCM1480_NR_IRQS; i++) { + irq_set_chip_and_handler(i, &bcm1480_irq_type, + handle_level_irq); + bcm1480_irq_owner[i] = 0; + } +} + +/* + * init_IRQ is called early in the boot sequence from init/main.c. It + * is responsible for setting up the interrupt mapper and installing the + * handler that will be responsible for dispatching interrupts to the + * "right" place. + */ +/* + * For now, map all interrupts to IP[2]. We could save + * some cycles by parceling out system interrupts to different + * IP lines, but keep it simple for bringup. We'll also direct + * all interrupts to a single CPU; we should probably route + * PCI and LDT to one cpu and everything else to the other + * to balance the load a bit. + * + * On the second cpu, everything is set to IP5, which is + * ignored, EXCEPT the mailbox interrupt. That one is + * set to IP[2] so it is handled. This is needed so we + * can do cross-cpu function calls, as required by SMP + */ + +#define IMR_IP2_VAL K_BCM1480_INT_MAP_I0 +#define IMR_IP3_VAL K_BCM1480_INT_MAP_I1 +#define IMR_IP4_VAL K_BCM1480_INT_MAP_I2 +#define IMR_IP5_VAL K_BCM1480_INT_MAP_I3 +#define IMR_IP6_VAL K_BCM1480_INT_MAP_I4 + +void __init arch_init_irq(void) +{ + unsigned int i, cpu; + u64 tmp; + unsigned int imask = STATUSF_IP4 | STATUSF_IP3 | STATUSF_IP2 | + STATUSF_IP1 | STATUSF_IP0; + + /* Default everything to IP2 */ + /* Start with _high registers which has no bit 0 interrupt source */ + for (i = 1; i < BCM1480_NR_IRQS_HALF; i++) { /* was I0 */ + for (cpu = 0; cpu < 4; cpu++) { + __raw_writeq(IMR_IP2_VAL, + IOADDR(A_BCM1480_IMR_REGISTER(cpu, + R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) + (i << 3))); + } + } + + /* Now do _low registers */ + for (i = 0; i < BCM1480_NR_IRQS_HALF; i++) { + for (cpu = 0; cpu < 4; cpu++) { + __raw_writeq(IMR_IP2_VAL, + IOADDR(A_BCM1480_IMR_REGISTER(cpu, + R_BCM1480_IMR_INTERRUPT_MAP_BASE_L) + (i << 3))); + } + } + + init_bcm1480_irqs(); + + /* + * Map the high 16 bits of mailbox_0 registers to IP[3], for + * inter-cpu messages + */ + /* Was I1 */ + for (cpu = 0; cpu < 4; cpu++) { + __raw_writeq(IMR_IP3_VAL, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) + + (K_BCM1480_INT_MBOX_0_0 << 3))); + } + + + /* Clear the mailboxes. The firmware may leave them dirty */ + for (cpu = 0; cpu < 4; cpu++) { + __raw_writeq(0xffffffffffffffffULL, + IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_MAILBOX_0_CLR_CPU))); + __raw_writeq(0xffffffffffffffffULL, + IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_MAILBOX_1_CLR_CPU))); + } + + + /* Mask everything except the high 16 bit of mailbox_0 registers for all cpus */ + tmp = ~((u64) 0) ^ ( (((u64) 1) << K_BCM1480_INT_MBOX_0_0)); + for (cpu = 0; cpu < 4; cpu++) { + __raw_writeq(tmp, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MASK_H))); + } + tmp = ~((u64) 0); + for (cpu = 0; cpu < 4; cpu++) { + __raw_writeq(tmp, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MASK_L))); + } + + /* + * Note that the timer interrupts are also mapped, but this is + * done in bcm1480_time_init(). Also, the profiling driver + * does its own management of IP7. + */ + + /* Enable necessary IPs, disable the rest */ + change_c0_status(ST0_IM, imask); +} + +extern void bcm1480_mailbox_interrupt(void); + +static inline void dispatch_ip2(void) +{ + unsigned long long mask_h, mask_l; + unsigned int cpu = smp_processor_id(); + unsigned long base; + + /* + * Default...we've hit an IP[2] interrupt, which means we've got to + * check the 1480 interrupt registers to figure out what to do. Need + * to detect which CPU we're on, now that smp_affinity is supported. + */ + base = A_BCM1480_IMR_MAPPER(cpu); + mask_h = __raw_readq( + IOADDR(base + R_BCM1480_IMR_INTERRUPT_STATUS_BASE_H)); + mask_l = __raw_readq( + IOADDR(base + R_BCM1480_IMR_INTERRUPT_STATUS_BASE_L)); + + if (mask_h) { + if (mask_h ^ 1) + do_IRQ(fls64(mask_h) - 1); + else if (mask_l) + do_IRQ(63 + fls64(mask_l)); + } +} + +asmlinkage void plat_irq_dispatch(void) +{ + unsigned int cpu = smp_processor_id(); + unsigned int pending; + + pending = read_c0_cause() & read_c0_status(); + + if (pending & CAUSEF_IP4) + do_IRQ(K_BCM1480_INT_TIMER_0 + cpu); +#ifdef CONFIG_SMP + else if (pending & CAUSEF_IP3) + bcm1480_mailbox_interrupt(); +#endif + + else if (pending & CAUSEF_IP2) + dispatch_ip2(); +} diff --git a/arch/mips/sibyte/bcm1480/setup.c b/arch/mips/sibyte/bcm1480/setup.c new file mode 100644 index 000000000..6f34b871b --- /dev/null +++ b/arch/mips/sibyte/bcm1480/setup.c @@ -0,0 +1,128 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Copyright (C) 2000,2001,2002,2003,2004 Broadcom Corporation + */ +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/export.h> +#include <linux/reboot.h> +#include <linux/string.h> + +#include <asm/bootinfo.h> +#include <asm/cpu.h> +#include <asm/mipsregs.h> +#include <asm/io.h> +#include <asm/sibyte/sb1250.h> + +#include <asm/sibyte/bcm1480_regs.h> +#include <asm/sibyte/bcm1480_scd.h> +#include <asm/sibyte/sb1250_scd.h> + +unsigned int sb1_pass; +unsigned int soc_pass; +unsigned int soc_type; +EXPORT_SYMBOL(soc_type); +unsigned int periph_rev; +EXPORT_SYMBOL_GPL(periph_rev); +unsigned int zbbus_mhz; +EXPORT_SYMBOL(zbbus_mhz); + +static unsigned int part_type; + +static char *soc_str; +static char *pass_str; + +static int __init setup_bcm1x80_bcm1x55(void) +{ + int ret = 0; + + switch (soc_pass) { + case K_SYS_REVISION_BCM1480_S0: + periph_rev = 1; + pass_str = "S0 (pass1)"; + break; + case K_SYS_REVISION_BCM1480_A1: + periph_rev = 1; + pass_str = "A1 (pass1)"; + break; + case K_SYS_REVISION_BCM1480_A2: + periph_rev = 1; + pass_str = "A2 (pass1)"; + break; + case K_SYS_REVISION_BCM1480_A3: + periph_rev = 1; + pass_str = "A3 (pass1)"; + break; + case K_SYS_REVISION_BCM1480_B0: + periph_rev = 1; + pass_str = "B0 (pass2)"; + break; + default: + printk("Unknown %s rev %x\n", soc_str, soc_pass); + periph_rev = 1; + pass_str = "Unknown Revision"; + break; + } + + return ret; +} + +/* Setup code likely to be common to all SiByte platforms */ + +static int __init sys_rev_decode(void) +{ + int ret = 0; + + switch (soc_type) { + case K_SYS_SOC_TYPE_BCM1x80: + if (part_type == K_SYS_PART_BCM1480) + soc_str = "BCM1480"; + else if (part_type == K_SYS_PART_BCM1280) + soc_str = "BCM1280"; + else + soc_str = "BCM1x80"; + ret = setup_bcm1x80_bcm1x55(); + break; + + case K_SYS_SOC_TYPE_BCM1x55: + if (part_type == K_SYS_PART_BCM1455) + soc_str = "BCM1455"; + else if (part_type == K_SYS_PART_BCM1255) + soc_str = "BCM1255"; + else + soc_str = "BCM1x55"; + ret = setup_bcm1x80_bcm1x55(); + break; + + default: + printk("Unknown part type %x\n", part_type); + ret = 1; + break; + } + + return ret; +} + +void __init bcm1480_setup(void) +{ + uint64_t sys_rev; + int plldiv; + + sb1_pass = read_c0_prid() & PRID_REV_MASK; + sys_rev = __raw_readq(IOADDR(A_SCD_SYSTEM_REVISION)); + soc_type = SYS_SOC_TYPE(sys_rev); + part_type = G_SYS_PART(sys_rev); + soc_pass = G_SYS_REVISION(sys_rev); + + if (sys_rev_decode()) { + printk("Restart after failure to identify SiByte chip\n"); + machine_restart(NULL); + } + + plldiv = G_BCM1480_SYS_PLL_DIV(__raw_readq(IOADDR(A_SCD_SYSTEM_CFG))); + zbbus_mhz = ((plldiv >> 1) * 50) + ((plldiv & 1) * 25); + + printk("Broadcom SiByte %s %s @ %d MHz (SB-1A rev %d)\n", + soc_str, pass_str, zbbus_mhz * 2, sb1_pass); + printk("Board type: %s\n", get_system_type()); +} diff --git a/arch/mips/sibyte/bcm1480/smp.c b/arch/mips/sibyte/bcm1480/smp.c new file mode 100644 index 000000000..5861e5025 --- /dev/null +++ b/arch/mips/sibyte/bcm1480/smp.c @@ -0,0 +1,179 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Copyright (C) 2001,2002,2004 Broadcom Corporation + */ + +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/smp.h> +#include <linux/kernel_stat.h> +#include <linux/sched.h> +#include <linux/sched/task_stack.h> + +#include <asm/mmu_context.h> +#include <asm/io.h> +#include <asm/fw/cfe/cfe_api.h> +#include <asm/sibyte/sb1250.h> +#include <asm/sibyte/bcm1480_regs.h> +#include <asm/sibyte/bcm1480_int.h> + +/* + * These are routines for dealing with the bcm1480 smp capabilities + * independent of board/firmware + */ + +static void *mailbox_0_set_regs[] = { + IOADDR(A_BCM1480_IMR_CPU0_BASE + R_BCM1480_IMR_MAILBOX_0_SET_CPU), + IOADDR(A_BCM1480_IMR_CPU1_BASE + R_BCM1480_IMR_MAILBOX_0_SET_CPU), + IOADDR(A_BCM1480_IMR_CPU2_BASE + R_BCM1480_IMR_MAILBOX_0_SET_CPU), + IOADDR(A_BCM1480_IMR_CPU3_BASE + R_BCM1480_IMR_MAILBOX_0_SET_CPU), +}; + +static void *mailbox_0_clear_regs[] = { + IOADDR(A_BCM1480_IMR_CPU0_BASE + R_BCM1480_IMR_MAILBOX_0_CLR_CPU), + IOADDR(A_BCM1480_IMR_CPU1_BASE + R_BCM1480_IMR_MAILBOX_0_CLR_CPU), + IOADDR(A_BCM1480_IMR_CPU2_BASE + R_BCM1480_IMR_MAILBOX_0_CLR_CPU), + IOADDR(A_BCM1480_IMR_CPU3_BASE + R_BCM1480_IMR_MAILBOX_0_CLR_CPU), +}; + +static void *mailbox_0_regs[] = { + IOADDR(A_BCM1480_IMR_CPU0_BASE + R_BCM1480_IMR_MAILBOX_0_CPU), + IOADDR(A_BCM1480_IMR_CPU1_BASE + R_BCM1480_IMR_MAILBOX_0_CPU), + IOADDR(A_BCM1480_IMR_CPU2_BASE + R_BCM1480_IMR_MAILBOX_0_CPU), + IOADDR(A_BCM1480_IMR_CPU3_BASE + R_BCM1480_IMR_MAILBOX_0_CPU), +}; + +/* + * SMP init and finish on secondary CPUs + */ +void bcm1480_smp_init(void) +{ + unsigned int imask = STATUSF_IP4 | STATUSF_IP3 | STATUSF_IP2 | + STATUSF_IP1 | STATUSF_IP0; + + /* Set interrupt mask, but don't enable */ + change_c0_status(ST0_IM, imask); +} + +/* + * These are routines for dealing with the sb1250 smp capabilities + * independent of board/firmware + */ + +/* + * Simple enough; everything is set up, so just poke the appropriate mailbox + * register, and we should be set + */ +static void bcm1480_send_ipi_single(int cpu, unsigned int action) +{ + __raw_writeq((((u64)action)<< 48), mailbox_0_set_regs[cpu]); +} + +static void bcm1480_send_ipi_mask(const struct cpumask *mask, + unsigned int action) +{ + unsigned int i; + + for_each_cpu(i, mask) + bcm1480_send_ipi_single(i, action); +} + +/* + * Code to run on secondary just after probing the CPU + */ +static void bcm1480_init_secondary(void) +{ + extern void bcm1480_smp_init(void); + + bcm1480_smp_init(); +} + +/* + * Do any tidying up before marking online and running the idle + * loop + */ +static void bcm1480_smp_finish(void) +{ + extern void sb1480_clockevent_init(void); + + sb1480_clockevent_init(); + local_irq_enable(); +} + +/* + * Setup the PC, SP, and GP of a secondary processor and start it + * running! + */ +static int bcm1480_boot_secondary(int cpu, struct task_struct *idle) +{ + int retval; + + retval = cfe_cpu_start(cpu_logical_map(cpu), &smp_bootstrap, + __KSTK_TOS(idle), + (unsigned long)task_thread_info(idle), 0); + if (retval != 0) + printk("cfe_start_cpu(%i) returned %i\n" , cpu, retval); + return retval; +} + +/* + * Use CFE to find out how many CPUs are available, setting up + * cpu_possible_mask and the logical/physical mappings. + * XXXKW will the boot CPU ever not be physical 0? + * + * Common setup before any secondaries are started + */ +static void __init bcm1480_smp_setup(void) +{ + int i, num; + + init_cpu_possible(cpumask_of(0)); + __cpu_number_map[0] = 0; + __cpu_logical_map[0] = 0; + + for (i = 1, num = 0; i < NR_CPUS; i++) { + if (cfe_cpu_stop(i) == 0) { + set_cpu_possible(i, true); + __cpu_number_map[i] = ++num; + __cpu_logical_map[num] = i; + } + } + printk(KERN_INFO "Detected %i available secondary CPU(s)\n", num); +} + +static void __init bcm1480_prepare_cpus(unsigned int max_cpus) +{ +} + +const struct plat_smp_ops bcm1480_smp_ops = { + .send_ipi_single = bcm1480_send_ipi_single, + .send_ipi_mask = bcm1480_send_ipi_mask, + .init_secondary = bcm1480_init_secondary, + .smp_finish = bcm1480_smp_finish, + .boot_secondary = bcm1480_boot_secondary, + .smp_setup = bcm1480_smp_setup, + .prepare_cpus = bcm1480_prepare_cpus, +}; + +void bcm1480_mailbox_interrupt(void) +{ + int cpu = smp_processor_id(); + int irq = K_BCM1480_INT_MBOX_0_0; + unsigned int action; + + kstat_incr_irq_this_cpu(irq); + /* Load the mailbox register to figure out what we're supposed to do */ + action = (__raw_readq(mailbox_0_regs[cpu]) >> 48) & 0xffff; + + /* Clear the mailbox to clear the interrupt */ + __raw_writeq(((u64)action)<<48, mailbox_0_clear_regs[cpu]); + + if (action & SMP_RESCHEDULE_YOURSELF) + scheduler_ipi(); + + if (action & SMP_CALL_FUNCTION) { + irq_enter(); + generic_smp_call_function_interrupt(); + irq_exit(); + } +} diff --git a/arch/mips/sibyte/bcm1480/time.c b/arch/mips/sibyte/bcm1480/time.c new file mode 100644 index 000000000..e6450d79f --- /dev/null +++ b/arch/mips/sibyte/bcm1480/time.c @@ -0,0 +1,14 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Copyright (C) 2000,2001,2004 Broadcom Corporation + */ +#include <linux/init.h> + +extern void sb1480_clockevent_init(void); +extern void sb1480_clocksource_init(void); + +void __init plat_time_init(void) +{ + sb1480_clocksource_init(); + sb1480_clockevent_init(); +} |