diff options
Diffstat (limited to 'arch/sh/mm/Kconfig')
| -rw-r--r-- | arch/sh/mm/Kconfig | 262 |
1 files changed, 262 insertions, 0 deletions
diff --git a/arch/sh/mm/Kconfig b/arch/sh/mm/Kconfig new file mode 100644 index 000000000..703d30699 --- /dev/null +++ b/arch/sh/mm/Kconfig @@ -0,0 +1,262 @@ +# SPDX-License-Identifier: GPL-2.0 +menu "Memory management options" + +config MMU + bool "Support for memory management hardware" + depends on !CPU_SH2 + default y + help + Some SH processors (such as SH-2/SH-2A) lack an MMU. In order to + boot on these systems, this option must not be set. + + On other systems (such as the SH-3 and 4) where an MMU exists, + turning this off will boot the kernel on these machines with the + MMU implicitly switched off. + +config PAGE_OFFSET + hex + default "0x80000000" if MMU + default "0x00000000" + +config FORCE_MAX_ZONEORDER + int "Maximum zone order" + range 9 64 if PAGE_SIZE_16KB + default "9" if PAGE_SIZE_16KB + range 7 64 if PAGE_SIZE_64KB + default "7" if PAGE_SIZE_64KB + range 11 64 + default "14" if !MMU + default "11" + help + The kernel memory allocator divides physically contiguous memory + blocks into "zones", where each zone is a power of two number of + pages. This option selects the largest power of two that the kernel + keeps in the memory allocator. If you need to allocate very large + blocks of physically contiguous memory, then you may need to + increase this value. + + This config option is actually maximum order plus one. For example, + a value of 11 means that the largest free memory block is 2^10 pages. + + The page size is not necessarily 4KB. Keep this in mind when + choosing a value for this option. + +config MEMORY_START + hex "Physical memory start address" + default "0x08000000" + help + Computers built with Hitachi SuperH processors always + map the ROM starting at address zero. But the processor + does not specify the range that RAM takes. + + The physical memory (RAM) start address will be automatically + set to 08000000. Other platforms, such as the Solution Engine + boards typically map RAM at 0C000000. + + Tweak this only when porting to a new machine which does not + already have a defconfig. Changing it from the known correct + value on any of the known systems will only lead to disaster. + +config MEMORY_SIZE + hex "Physical memory size" + default "0x04000000" + help + This sets the default memory size assumed by your SH kernel. It can + be overridden as normal by the 'mem=' argument on the kernel command + line. If unsure, consult your board specifications or just leave it + as 0x04000000 which was the default value before this became + configurable. + +# Physical addressing modes + +config 29BIT + def_bool !32BIT + select UNCACHED_MAPPING + +config 32BIT + bool + default !MMU + +config PMB + bool "Support 32-bit physical addressing through PMB" + depends on MMU && CPU_SH4A && !CPU_SH4AL_DSP + select 32BIT + select UNCACHED_MAPPING + help + If you say Y here, physical addressing will be extended to + 32-bits through the SH-4A PMB. If this is not set, legacy + 29-bit physical addressing will be used. + +config X2TLB + def_bool y + depends on (CPU_SHX2 || CPU_SHX3) && MMU + +config VSYSCALL + bool "Support vsyscall page" + depends on MMU && (CPU_SH3 || CPU_SH4) + default y + help + This will enable support for the kernel mapping a vDSO page + in process space, and subsequently handing down the entry point + to the libc through the ELF auxiliary vector. + + From the kernel side this is used for the signal trampoline. + For systems with an MMU that can afford to give up a page, + (the default value) say Y. + +config NUMA + bool "Non Uniform Memory Access (NUMA) Support" + depends on MMU && SYS_SUPPORTS_NUMA + select ARCH_WANT_NUMA_VARIABLE_LOCALITY + default n + help + Some SH systems have many various memories scattered around + the address space, each with varying latencies. This enables + support for these blocks by binding them to nodes and allowing + memory policies to be used for prioritizing and controlling + allocation behaviour. + +config NODES_SHIFT + int + default "3" if CPU_SUBTYPE_SHX3 + default "1" + depends on NEED_MULTIPLE_NODES + +config ARCH_FLATMEM_ENABLE + def_bool y + depends on !NUMA + +config ARCH_SPARSEMEM_ENABLE + def_bool y + select SPARSEMEM_STATIC + +config ARCH_SPARSEMEM_DEFAULT + def_bool y + +config ARCH_SELECT_MEMORY_MODEL + def_bool y + +config ARCH_ENABLE_MEMORY_HOTPLUG + def_bool y + depends on SPARSEMEM && MMU + +config ARCH_ENABLE_MEMORY_HOTREMOVE + def_bool y + depends on SPARSEMEM && MMU + +config ARCH_MEMORY_PROBE + def_bool y + depends on MEMORY_HOTPLUG + +config IOREMAP_FIXED + def_bool y + depends on X2TLB + +config UNCACHED_MAPPING + bool + +config HAVE_SRAM_POOL + bool + select GENERIC_ALLOCATOR + +choice + prompt "Kernel page size" + default PAGE_SIZE_4KB + +config PAGE_SIZE_4KB + bool "4kB" + help + This is the default page size used by all SuperH CPUs. + +config PAGE_SIZE_8KB + bool "8kB" + depends on !MMU || X2TLB + help + This enables 8kB pages as supported by SH-X2 and later MMUs. + +config PAGE_SIZE_16KB + bool "16kB" + depends on !MMU + help + This enables 16kB pages on MMU-less SH systems. + +config PAGE_SIZE_64KB + bool "64kB" + depends on !MMU || CPU_SH4 + help + This enables support for 64kB pages, possible on all SH-4 + CPUs and later. + +endchoice + +choice + prompt "HugeTLB page size" + depends on HUGETLB_PAGE + default HUGETLB_PAGE_SIZE_1MB if PAGE_SIZE_64KB + default HUGETLB_PAGE_SIZE_64K + +config HUGETLB_PAGE_SIZE_64K + bool "64kB" + depends on !PAGE_SIZE_64KB + +config HUGETLB_PAGE_SIZE_256K + bool "256kB" + depends on X2TLB + +config HUGETLB_PAGE_SIZE_1MB + bool "1MB" + +config HUGETLB_PAGE_SIZE_4MB + bool "4MB" + depends on X2TLB + +config HUGETLB_PAGE_SIZE_64MB + bool "64MB" + depends on X2TLB + +endchoice + +config SCHED_MC + bool "Multi-core scheduler support" + depends on SMP + default y + help + Multi-core scheduler support improves the CPU scheduler's decision + making when dealing with multi-core CPU chips at a cost of slightly + increased overhead in some places. If unsure say N here. + +endmenu + +menu "Cache configuration" + +config SH7705_CACHE_32KB + bool "Enable 32KB cache size for SH7705" + depends on CPU_SUBTYPE_SH7705 + default y + +choice + prompt "Cache mode" + default CACHE_WRITEBACK if CPU_SH2A || CPU_SH3 || CPU_SH4 + default CACHE_WRITETHROUGH if (CPU_SH2 && !CPU_SH2A) + +config CACHE_WRITEBACK + bool "Write-back" + +config CACHE_WRITETHROUGH + bool "Write-through" + help + Selecting this option will configure the caches in write-through + mode, as opposed to the default write-back configuration. + + Since there's sill some aliasing issues on SH-4, this option will + unfortunately still require the majority of flushing functions to + be implemented to deal with aliasing. + + If unsure, say N. + +config CACHE_OFF + bool "Off" + +endchoice + +endmenu |