diff options
Diffstat (limited to 'drivers/ata/pata_radisys.c')
| -rw-r--r-- | drivers/ata/pata_radisys.c | 253 |
1 files changed, 253 insertions, 0 deletions
diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c new file mode 100644 index 000000000..8fde4a864 --- /dev/null +++ b/drivers/ata/pata_radisys.c @@ -0,0 +1,253 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * pata_radisys.c - Intel PATA/SATA controllers + * + * (C) 2006 Red Hat <alan@lxorguk.ukuu.org.uk> + * + * Some parts based on ata_piix.c by Jeff Garzik and others. + * + * A PIIX relative, this device has a single ATA channel and no + * slave timings, SITRE or PPE. In that sense it is a close relative + * of the original PIIX. It does however support UDMA 33/66 per channel + * although no other modes/timings. Also lacking is 32bit I/O on the ATA + * port. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/ata.h> + +#define DRV_NAME "pata_radisys" +#define DRV_VERSION "0.4.4" + +/** + * radisys_set_piomode - Initialize host controller PATA PIO timings + * @ap: ATA port + * @adev: Device whose timings we are configuring + * + * Set PIO mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void radisys_set_piomode (struct ata_port *ap, struct ata_device *adev) +{ + unsigned int pio = adev->pio_mode - XFER_PIO_0; + struct pci_dev *dev = to_pci_dev(ap->host->dev); + u16 idetm_data; + int control = 0; + + /* + * See Intel Document 298600-004 for the timing programing rules + * for PIIX/ICH. Note that the early PIIX does not have the slave + * timing port at 0x44. The Radisys is a relative of the PIIX + * but not the same so be careful. + */ + + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, /* Check me */ + { 0, 0 }, + { 1, 1 }, + { 2, 2 }, + { 3, 3 }, }; + + if (pio > 0) + control |= 1; /* TIME1 enable */ + if (ata_pio_need_iordy(adev)) + control |= 2; /* IE IORDY */ + + pci_read_config_word(dev, 0x40, &idetm_data); + + /* Enable IE and TIME as appropriate. Clear the other + drive timing bits */ + idetm_data &= 0xCCCC; + idetm_data |= (control << (4 * adev->devno)); + idetm_data |= (timings[pio][0] << 12) | + (timings[pio][1] << 8); + pci_write_config_word(dev, 0x40, idetm_data); + + /* Track which port is configured */ + ap->private_data = adev; +} + +/** + * radisys_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * + * Set MWDMA mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void radisys_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *dev = to_pci_dev(ap->host->dev); + u16 idetm_data; + u8 udma_enable; + + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, + { 0, 0 }, + { 1, 1 }, + { 2, 2 }, + { 3, 3 }, }; + + /* + * MWDMA is driven by the PIO timings. We must also enable + * IORDY unconditionally. + */ + + pci_read_config_word(dev, 0x40, &idetm_data); + pci_read_config_byte(dev, 0x48, &udma_enable); + + if (adev->dma_mode < XFER_UDMA_0) { + unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0; + const unsigned int needed_pio[3] = { + XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 + }; + int pio = needed_pio[mwdma] - XFER_PIO_0; + int control = 3; /* IORDY|TIME0 */ + + /* If the drive MWDMA is faster than it can do PIO then + we must force PIO0 for PIO cycles. */ + + if (adev->pio_mode < needed_pio[mwdma]) + control = 1; + + /* Mask out the relevant control and timing bits we will load. Also + clear the other drive TIME register as a precaution */ + + idetm_data &= 0xCCCC; + idetm_data |= control << (4 * adev->devno); + idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8); + + udma_enable &= ~(1 << adev->devno); + } else { + u8 udma_mode; + + /* UDMA66 on: UDMA 33 and 66 are switchable via register 0x4A */ + + pci_read_config_byte(dev, 0x4A, &udma_mode); + + if (adev->xfer_mode == XFER_UDMA_2) + udma_mode &= ~(2 << (adev->devno * 4)); + else /* UDMA 4 */ + udma_mode |= (2 << (adev->devno * 4)); + + pci_write_config_byte(dev, 0x4A, udma_mode); + + udma_enable |= (1 << adev->devno); + } + pci_write_config_word(dev, 0x40, idetm_data); + pci_write_config_byte(dev, 0x48, udma_enable); + + /* Track which port is configured */ + ap->private_data = adev; +} + +/** + * radisys_qc_issue - command issue + * @qc: command pending + * + * Called when the libata layer is about to issue a command. We wrap + * this interface so that we can load the correct ATA timings if + * necessary. Our logic also clears TIME0/TIME1 for the other device so + * that, even if we get this wrong, cycles to the other device will + * be made PIO0. + */ + +static unsigned int radisys_qc_issue(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + + if (adev != ap->private_data) { + /* UDMA timing is not shared */ + if (adev->dma_mode < XFER_UDMA_0) { + if (adev->dma_mode) + radisys_set_dmamode(ap, adev); + else if (adev->pio_mode) + radisys_set_piomode(ap, adev); + } + } + return ata_bmdma_qc_issue(qc); +} + + +static struct scsi_host_template radisys_sht = { + ATA_BMDMA_SHT(DRV_NAME), +}; + +static struct ata_port_operations radisys_pata_ops = { + .inherits = &ata_bmdma_port_ops, + .qc_issue = radisys_qc_issue, + .cable_detect = ata_cable_unknown, + .set_piomode = radisys_set_piomode, + .set_dmamode = radisys_set_dmamode, +}; + + +/** + * radisys_init_one - Register PIIX ATA PCI device with kernel services + * @pdev: PCI device to register + * @ent: Entry in radisys_pci_tbl matching with @pdev + * + * Called from kernel PCI layer. We probe for combined mode (sigh), + * and then hand over control to libata, for it to do the rest. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static const struct ata_port_info info = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA12_ONLY, + .udma_mask = ATA_UDMA24_ONLY, + .port_ops = &radisys_pata_ops, + }; + const struct ata_port_info *ppi[] = { &info, NULL }; + + ata_print_version_once(&pdev->dev, DRV_VERSION); + + return ata_pci_bmdma_init_one(pdev, ppi, &radisys_sht, NULL, 0); +} + +static const struct pci_device_id radisys_pci_tbl[] = { + { PCI_VDEVICE(RADISYS, 0x8201), }, + + { } /* terminate list */ +}; + +static struct pci_driver radisys_pci_driver = { + .name = DRV_NAME, + .id_table = radisys_pci_tbl, + .probe = radisys_init_one, + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM_SLEEP + .suspend = ata_pci_device_suspend, + .resume = ata_pci_device_resume, +#endif +}; + +module_pci_driver(radisys_pci_driver); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("SCSI low-level driver for Radisys R82600 controllers"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, radisys_pci_tbl); +MODULE_VERSION(DRV_VERSION); |