diff options
Diffstat (limited to 'drivers/mmc/host/sdhci-of-arasan.c')
| -rw-r--r-- | drivers/mmc/host/sdhci-of-arasan.c | 1729 |
1 files changed, 1729 insertions, 0 deletions
diff --git a/drivers/mmc/host/sdhci-of-arasan.c b/drivers/mmc/host/sdhci-of-arasan.c new file mode 100644 index 000000000..9da49dc15 --- /dev/null +++ b/drivers/mmc/host/sdhci-of-arasan.c @@ -0,0 +1,1729 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Arasan Secure Digital Host Controller Interface. + * Copyright (C) 2011 - 2012 Michal Simek <monstr@monstr.eu> + * Copyright (c) 2012 Wind River Systems, Inc. + * Copyright (C) 2013 Pengutronix e.K. + * Copyright (C) 2013 Xilinx Inc. + * + * Based on sdhci-of-esdhc.c + * + * Copyright (c) 2007 Freescale Semiconductor, Inc. + * Copyright (c) 2009 MontaVista Software, Inc. + * + * Authors: Xiaobo Xie <X.Xie@freescale.com> + * Anton Vorontsov <avorontsov@ru.mvista.com> + */ + +#include <linux/clk-provider.h> +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/phy/phy.h> +#include <linux/regmap.h> +#include <linux/of.h> +#include <linux/firmware/xlnx-zynqmp.h> + +#include "cqhci.h" +#include "sdhci-cqhci.h" +#include "sdhci-pltfm.h" + +#define SDHCI_ARASAN_VENDOR_REGISTER 0x78 + +#define SDHCI_ARASAN_ITAPDLY_REGISTER 0xF0F8 +#define SDHCI_ARASAN_ITAPDLY_SEL_MASK 0xFF + +#define SDHCI_ARASAN_OTAPDLY_REGISTER 0xF0FC +#define SDHCI_ARASAN_OTAPDLY_SEL_MASK 0x3F + +#define SDHCI_ARASAN_CQE_BASE_ADDR 0x200 +#define VENDOR_ENHANCED_STROBE BIT(0) + +#define PHY_CLK_TOO_SLOW_HZ 400000 + +#define SDHCI_ITAPDLY_CHGWIN 0x200 +#define SDHCI_ITAPDLY_ENABLE 0x100 +#define SDHCI_OTAPDLY_ENABLE 0x40 + +/* Default settings for ZynqMP Clock Phases */ +#define ZYNQMP_ICLK_PHASE {0, 63, 63, 0, 63, 0, 0, 183, 54, 0, 0} +#define ZYNQMP_OCLK_PHASE {0, 72, 60, 0, 60, 72, 135, 48, 72, 135, 0} + +#define VERSAL_ICLK_PHASE {0, 132, 132, 0, 132, 0, 0, 162, 90, 0, 0} +#define VERSAL_OCLK_PHASE {0, 60, 48, 0, 48, 72, 90, 36, 60, 90, 0} + +/* + * On some SoCs the syscon area has a feature where the upper 16-bits of + * each 32-bit register act as a write mask for the lower 16-bits. This allows + * atomic updates of the register without locking. This macro is used on SoCs + * that have that feature. + */ +#define HIWORD_UPDATE(val, mask, shift) \ + ((val) << (shift) | (mask) << ((shift) + 16)) + +/** + * struct sdhci_arasan_soc_ctl_field - Field used in sdhci_arasan_soc_ctl_map + * + * @reg: Offset within the syscon of the register containing this field + * @width: Number of bits for this field + * @shift: Bit offset within @reg of this field (or -1 if not avail) + */ +struct sdhci_arasan_soc_ctl_field { + u32 reg; + u16 width; + s16 shift; +}; + +/** + * struct sdhci_arasan_soc_ctl_map - Map in syscon to corecfg registers + * + * @baseclkfreq: Where to find corecfg_baseclkfreq + * @clockmultiplier: Where to find corecfg_clockmultiplier + * @support64b: Where to find SUPPORT64B bit + * @hiword_update: If true, use HIWORD_UPDATE to access the syscon + * + * It's up to the licensee of the Arsan IP block to make these available + * somewhere if needed. Presumably these will be scattered somewhere that's + * accessible via the syscon API. + */ +struct sdhci_arasan_soc_ctl_map { + struct sdhci_arasan_soc_ctl_field baseclkfreq; + struct sdhci_arasan_soc_ctl_field clockmultiplier; + struct sdhci_arasan_soc_ctl_field support64b; + bool hiword_update; +}; + +/** + * struct sdhci_arasan_clk_ops - Clock Operations for Arasan SD controller + * + * @sdcardclk_ops: The output clock related operations + * @sampleclk_ops: The sample clock related operations + */ +struct sdhci_arasan_clk_ops { + const struct clk_ops *sdcardclk_ops; + const struct clk_ops *sampleclk_ops; +}; + +/** + * struct sdhci_arasan_clk_data - Arasan Controller Clock Data. + * + * @sdcardclk_hw: Struct for the clock we might provide to a PHY. + * @sdcardclk: Pointer to normal 'struct clock' for sdcardclk_hw. + * @sampleclk_hw: Struct for the clock we might provide to a PHY. + * @sampleclk: Pointer to normal 'struct clock' for sampleclk_hw. + * @clk_phase_in: Array of Input Clock Phase Delays for all speed modes + * @clk_phase_out: Array of Output Clock Phase Delays for all speed modes + * @set_clk_delays: Function pointer for setting Clock Delays + * @clk_of_data: Platform specific runtime clock data storage pointer + */ +struct sdhci_arasan_clk_data { + struct clk_hw sdcardclk_hw; + struct clk *sdcardclk; + struct clk_hw sampleclk_hw; + struct clk *sampleclk; + int clk_phase_in[MMC_TIMING_MMC_HS400 + 1]; + int clk_phase_out[MMC_TIMING_MMC_HS400 + 1]; + void (*set_clk_delays)(struct sdhci_host *host); + void *clk_of_data; +}; + +/** + * struct sdhci_arasan_data - Arasan Controller Data + * + * @host: Pointer to the main SDHCI host structure. + * @clk_ahb: Pointer to the AHB clock + * @phy: Pointer to the generic phy + * @is_phy_on: True if the PHY is on; false if not. + * @has_cqe: True if controller has command queuing engine. + * @clk_data: Struct for the Arasan Controller Clock Data. + * @clk_ops: Struct for the Arasan Controller Clock Operations. + * @soc_ctl_base: Pointer to regmap for syscon for soc_ctl registers. + * @soc_ctl_map: Map to get offsets into soc_ctl registers. + * @quirks: Arasan deviations from spec. + */ +struct sdhci_arasan_data { + struct sdhci_host *host; + struct clk *clk_ahb; + struct phy *phy; + bool is_phy_on; + + bool has_cqe; + struct sdhci_arasan_clk_data clk_data; + const struct sdhci_arasan_clk_ops *clk_ops; + + struct regmap *soc_ctl_base; + const struct sdhci_arasan_soc_ctl_map *soc_ctl_map; + unsigned int quirks; + +/* Controller does not have CD wired and will not function normally without */ +#define SDHCI_ARASAN_QUIRK_FORCE_CDTEST BIT(0) +/* Controller immediately reports SDHCI_CLOCK_INT_STABLE after enabling the + * internal clock even when the clock isn't stable */ +#define SDHCI_ARASAN_QUIRK_CLOCK_UNSTABLE BIT(1) +/* + * Some of the Arasan variations might not have timing requirements + * met at 25MHz for Default Speed mode, those controllers work at + * 19MHz instead + */ +#define SDHCI_ARASAN_QUIRK_CLOCK_25_BROKEN BIT(2) +}; + +struct sdhci_arasan_of_data { + const struct sdhci_arasan_soc_ctl_map *soc_ctl_map; + const struct sdhci_pltfm_data *pdata; + const struct sdhci_arasan_clk_ops *clk_ops; +}; + +static const struct sdhci_arasan_soc_ctl_map rk3399_soc_ctl_map = { + .baseclkfreq = { .reg = 0xf000, .width = 8, .shift = 8 }, + .clockmultiplier = { .reg = 0xf02c, .width = 8, .shift = 0}, + .hiword_update = true, +}; + +static const struct sdhci_arasan_soc_ctl_map intel_lgm_emmc_soc_ctl_map = { + .baseclkfreq = { .reg = 0xa0, .width = 8, .shift = 2 }, + .clockmultiplier = { .reg = 0, .width = -1, .shift = -1 }, + .hiword_update = false, +}; + +static const struct sdhci_arasan_soc_ctl_map intel_lgm_sdxc_soc_ctl_map = { + .baseclkfreq = { .reg = 0x80, .width = 8, .shift = 2 }, + .clockmultiplier = { .reg = 0, .width = -1, .shift = -1 }, + .hiword_update = false, +}; + +static const struct sdhci_arasan_soc_ctl_map intel_keembay_soc_ctl_map = { + .baseclkfreq = { .reg = 0x0, .width = 8, .shift = 14 }, + .clockmultiplier = { .reg = 0x4, .width = 8, .shift = 14 }, + .support64b = { .reg = 0x4, .width = 1, .shift = 24 }, + .hiword_update = false, +}; + +/** + * sdhci_arasan_syscon_write - Write to a field in soc_ctl registers + * + * @host: The sdhci_host + * @fld: The field to write to + * @val: The value to write + * + * This function allows writing to fields in sdhci_arasan_soc_ctl_map. + * Note that if a field is specified as not available (shift < 0) then + * this function will silently return an error code. It will be noisy + * and print errors for any other (unexpected) errors. + * + * Return: 0 on success and error value on error + */ +static int sdhci_arasan_syscon_write(struct sdhci_host *host, + const struct sdhci_arasan_soc_ctl_field *fld, + u32 val) +{ + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host); + struct regmap *soc_ctl_base = sdhci_arasan->soc_ctl_base; + u32 reg = fld->reg; + u16 width = fld->width; + s16 shift = fld->shift; + int ret; + + /* + * Silently return errors for shift < 0 so caller doesn't have + * to check for fields which are optional. For fields that + * are required then caller needs to do something special + * anyway. + */ + if (shift < 0) + return -EINVAL; + + if (sdhci_arasan->soc_ctl_map->hiword_update) + ret = regmap_write(soc_ctl_base, reg, + HIWORD_UPDATE(val, GENMASK(width, 0), + shift)); + else + ret = regmap_update_bits(soc_ctl_base, reg, + GENMASK(shift + width, shift), + val << shift); + + /* Yell about (unexpected) regmap errors */ + if (ret) + pr_warn("%s: Regmap write fail: %d\n", + mmc_hostname(host->mmc), ret); + + return ret; +} + +static void sdhci_arasan_set_clock(struct sdhci_host *host, unsigned int clock) +{ + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host); + struct sdhci_arasan_clk_data *clk_data = &sdhci_arasan->clk_data; + bool ctrl_phy = false; + + if (!IS_ERR(sdhci_arasan->phy)) { + if (!sdhci_arasan->is_phy_on && clock <= PHY_CLK_TOO_SLOW_HZ) { + /* + * If PHY off, set clock to max speed and power PHY on. + * + * Although PHY docs apparently suggest power cycling + * when changing the clock the PHY doesn't like to be + * powered on while at low speeds like those used in ID + * mode. Even worse is powering the PHY on while the + * clock is off. + * + * To workaround the PHY limitations, the best we can + * do is to power it on at a faster speed and then slam + * through low speeds without power cycling. + */ + sdhci_set_clock(host, host->max_clk); + if (phy_power_on(sdhci_arasan->phy)) { + pr_err("%s: Cannot power on phy.\n", + mmc_hostname(host->mmc)); + return; + } + + sdhci_arasan->is_phy_on = true; + + /* + * We'll now fall through to the below case with + * ctrl_phy = false (so we won't turn off/on). The + * sdhci_set_clock() will set the real clock. + */ + } else if (clock > PHY_CLK_TOO_SLOW_HZ) { + /* + * At higher clock speeds the PHY is fine being power + * cycled and docs say you _should_ power cycle when + * changing clock speeds. + */ + ctrl_phy = true; + } + } + + if (ctrl_phy && sdhci_arasan->is_phy_on) { + phy_power_off(sdhci_arasan->phy); + sdhci_arasan->is_phy_on = false; + } + + if (sdhci_arasan->quirks & SDHCI_ARASAN_QUIRK_CLOCK_25_BROKEN) { + /* + * Some of the Arasan variations might not have timing + * requirements met at 25MHz for Default Speed mode, + * those controllers work at 19MHz instead. + */ + if (clock == DEFAULT_SPEED_MAX_DTR) + clock = (DEFAULT_SPEED_MAX_DTR * 19) / 25; + } + + /* Set the Input and Output Clock Phase Delays */ + if (clk_data->set_clk_delays) + clk_data->set_clk_delays(host); + + sdhci_set_clock(host, clock); + + if (sdhci_arasan->quirks & SDHCI_ARASAN_QUIRK_CLOCK_UNSTABLE) + /* + * Some controllers immediately report SDHCI_CLOCK_INT_STABLE + * after enabling the clock even though the clock is not + * stable. Trying to use a clock without waiting here results + * in EILSEQ while detecting some older/slower cards. The + * chosen delay is the maximum delay from sdhci_set_clock. + */ + msleep(20); + + if (ctrl_phy) { + if (phy_power_on(sdhci_arasan->phy)) { + pr_err("%s: Cannot power on phy.\n", + mmc_hostname(host->mmc)); + return; + } + + sdhci_arasan->is_phy_on = true; + } +} + +static void sdhci_arasan_hs400_enhanced_strobe(struct mmc_host *mmc, + struct mmc_ios *ios) +{ + u32 vendor; + struct sdhci_host *host = mmc_priv(mmc); + + vendor = sdhci_readl(host, SDHCI_ARASAN_VENDOR_REGISTER); + if (ios->enhanced_strobe) + vendor |= VENDOR_ENHANCED_STROBE; + else + vendor &= ~VENDOR_ENHANCED_STROBE; + + sdhci_writel(host, vendor, SDHCI_ARASAN_VENDOR_REGISTER); +} + +static void sdhci_arasan_reset(struct sdhci_host *host, u8 mask) +{ + u8 ctrl; + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host); + + sdhci_and_cqhci_reset(host, mask); + + if (sdhci_arasan->quirks & SDHCI_ARASAN_QUIRK_FORCE_CDTEST) { + ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL); + ctrl |= SDHCI_CTRL_CDTEST_INS | SDHCI_CTRL_CDTEST_EN; + sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL); + } +} + +static int sdhci_arasan_voltage_switch(struct mmc_host *mmc, + struct mmc_ios *ios) +{ + switch (ios->signal_voltage) { + case MMC_SIGNAL_VOLTAGE_180: + /* + * Plese don't switch to 1V8 as arasan,5.1 doesn't + * actually refer to this setting to indicate the + * signal voltage and the state machine will be broken + * actually if we force to enable 1V8. That's something + * like broken quirk but we could work around here. + */ + return 0; + case MMC_SIGNAL_VOLTAGE_330: + case MMC_SIGNAL_VOLTAGE_120: + /* We don't support 3V3 and 1V2 */ + break; + } + + return -EINVAL; +} + +static const struct sdhci_ops sdhci_arasan_ops = { + .set_clock = sdhci_arasan_set_clock, + .get_max_clock = sdhci_pltfm_clk_get_max_clock, + .get_timeout_clock = sdhci_pltfm_clk_get_max_clock, + .set_bus_width = sdhci_set_bus_width, + .reset = sdhci_arasan_reset, + .set_uhs_signaling = sdhci_set_uhs_signaling, + .set_power = sdhci_set_power_and_bus_voltage, +}; + +static u32 sdhci_arasan_cqhci_irq(struct sdhci_host *host, u32 intmask) +{ + int cmd_error = 0; + int data_error = 0; + + if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error)) + return intmask; + + cqhci_irq(host->mmc, intmask, cmd_error, data_error); + + return 0; +} + +static void sdhci_arasan_dumpregs(struct mmc_host *mmc) +{ + sdhci_dumpregs(mmc_priv(mmc)); +} + +static void sdhci_arasan_cqe_enable(struct mmc_host *mmc) +{ + struct sdhci_host *host = mmc_priv(mmc); + u32 reg; + + reg = sdhci_readl(host, SDHCI_PRESENT_STATE); + while (reg & SDHCI_DATA_AVAILABLE) { + sdhci_readl(host, SDHCI_BUFFER); + reg = sdhci_readl(host, SDHCI_PRESENT_STATE); + } + + sdhci_cqe_enable(mmc); +} + +static const struct cqhci_host_ops sdhci_arasan_cqhci_ops = { + .enable = sdhci_arasan_cqe_enable, + .disable = sdhci_cqe_disable, + .dumpregs = sdhci_arasan_dumpregs, +}; + +static const struct sdhci_ops sdhci_arasan_cqe_ops = { + .set_clock = sdhci_arasan_set_clock, + .get_max_clock = sdhci_pltfm_clk_get_max_clock, + .get_timeout_clock = sdhci_pltfm_clk_get_max_clock, + .set_bus_width = sdhci_set_bus_width, + .reset = sdhci_arasan_reset, + .set_uhs_signaling = sdhci_set_uhs_signaling, + .set_power = sdhci_set_power_and_bus_voltage, + .irq = sdhci_arasan_cqhci_irq, +}; + +static const struct sdhci_pltfm_data sdhci_arasan_cqe_pdata = { + .ops = &sdhci_arasan_cqe_ops, + .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN, + .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN | + SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN, +}; + +#ifdef CONFIG_PM_SLEEP +/** + * sdhci_arasan_suspend - Suspend method for the driver + * @dev: Address of the device structure + * + * Put the device in a low power state. + * + * Return: 0 on success and error value on error + */ +static int sdhci_arasan_suspend(struct device *dev) +{ + struct sdhci_host *host = dev_get_drvdata(dev); + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host); + int ret; + + if (host->tuning_mode != SDHCI_TUNING_MODE_3) + mmc_retune_needed(host->mmc); + + if (sdhci_arasan->has_cqe) { + ret = cqhci_suspend(host->mmc); + if (ret) + return ret; + } + + ret = sdhci_suspend_host(host); + if (ret) + return ret; + + if (!IS_ERR(sdhci_arasan->phy) && sdhci_arasan->is_phy_on) { + ret = phy_power_off(sdhci_arasan->phy); + if (ret) { + dev_err(dev, "Cannot power off phy.\n"); + if (sdhci_resume_host(host)) + dev_err(dev, "Cannot resume host.\n"); + + return ret; + } + sdhci_arasan->is_phy_on = false; + } + + clk_disable(pltfm_host->clk); + clk_disable(sdhci_arasan->clk_ahb); + + return 0; +} + +/** + * sdhci_arasan_resume - Resume method for the driver + * @dev: Address of the device structure + * + * Resume operation after suspend + * + * Return: 0 on success and error value on error + */ +static int sdhci_arasan_resume(struct device *dev) +{ + struct sdhci_host *host = dev_get_drvdata(dev); + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host); + int ret; + + ret = clk_enable(sdhci_arasan->clk_ahb); + if (ret) { + dev_err(dev, "Cannot enable AHB clock.\n"); + return ret; + } + + ret = clk_enable(pltfm_host->clk); + if (ret) { + dev_err(dev, "Cannot enable SD clock.\n"); + return ret; + } + + if (!IS_ERR(sdhci_arasan->phy) && host->mmc->actual_clock) { + ret = phy_power_on(sdhci_arasan->phy); + if (ret) { + dev_err(dev, "Cannot power on phy.\n"); + return ret; + } + sdhci_arasan->is_phy_on = true; + } + + ret = sdhci_resume_host(host); + if (ret) { + dev_err(dev, "Cannot resume host.\n"); + return ret; + } + + if (sdhci_arasan->has_cqe) + return cqhci_resume(host->mmc); + + return 0; +} +#endif /* ! CONFIG_PM_SLEEP */ + +static SIMPLE_DEV_PM_OPS(sdhci_arasan_dev_pm_ops, sdhci_arasan_suspend, + sdhci_arasan_resume); + +/** + * sdhci_arasan_sdcardclk_recalc_rate - Return the card clock rate + * + * @hw: Pointer to the hardware clock structure. + * @parent_rate: The parent rate (should be rate of clk_xin). + * + * Return the current actual rate of the SD card clock. This can be used + * to communicate with out PHY. + * + * Return: The card clock rate. + */ +static unsigned long sdhci_arasan_sdcardclk_recalc_rate(struct clk_hw *hw, + unsigned long parent_rate) +{ + struct sdhci_arasan_clk_data *clk_data = + container_of(hw, struct sdhci_arasan_clk_data, sdcardclk_hw); + struct sdhci_arasan_data *sdhci_arasan = + container_of(clk_data, struct sdhci_arasan_data, clk_data); + struct sdhci_host *host = sdhci_arasan->host; + + return host->mmc->actual_clock; +} + +static const struct clk_ops arasan_sdcardclk_ops = { + .recalc_rate = sdhci_arasan_sdcardclk_recalc_rate, +}; + +/** + * sdhci_arasan_sampleclk_recalc_rate - Return the sampling clock rate + * + * @hw: Pointer to the hardware clock structure. + * @parent_rate: The parent rate (should be rate of clk_xin). + * + * Return the current actual rate of the sampling clock. This can be used + * to communicate with out PHY. + * + * Return: The sample clock rate. + */ +static unsigned long sdhci_arasan_sampleclk_recalc_rate(struct clk_hw *hw, + unsigned long parent_rate) +{ + struct sdhci_arasan_clk_data *clk_data = + container_of(hw, struct sdhci_arasan_clk_data, sampleclk_hw); + struct sdhci_arasan_data *sdhci_arasan = + container_of(clk_data, struct sdhci_arasan_data, clk_data); + struct sdhci_host *host = sdhci_arasan->host; + + return host->mmc->actual_clock; +} + +static const struct clk_ops arasan_sampleclk_ops = { + .recalc_rate = sdhci_arasan_sampleclk_recalc_rate, +}; + +/** + * sdhci_zynqmp_sdcardclk_set_phase - Set the SD Output Clock Tap Delays + * + * @hw: Pointer to the hardware clock structure. + * @degrees: The clock phase shift between 0 - 359. + * + * Set the SD Output Clock Tap Delays for Output path + * + * Return: 0 on success and error value on error + */ +static int sdhci_zynqmp_sdcardclk_set_phase(struct clk_hw *hw, int degrees) +{ + struct sdhci_arasan_clk_data *clk_data = + container_of(hw, struct sdhci_arasan_clk_data, sdcardclk_hw); + struct sdhci_arasan_data *sdhci_arasan = + container_of(clk_data, struct sdhci_arasan_data, clk_data); + struct sdhci_host *host = sdhci_arasan->host; + const char *clk_name = clk_hw_get_name(hw); + u32 node_id = !strcmp(clk_name, "clk_out_sd0") ? NODE_SD_0 : NODE_SD_1; + u8 tap_delay, tap_max = 0; + int ret; + + /* This is applicable for SDHCI_SPEC_300 and above */ + if (host->version < SDHCI_SPEC_300) + return 0; + + switch (host->timing) { + case MMC_TIMING_MMC_HS: + case MMC_TIMING_SD_HS: + case MMC_TIMING_UHS_SDR25: + case MMC_TIMING_UHS_DDR50: + case MMC_TIMING_MMC_DDR52: + /* For 50MHz clock, 30 Taps are available */ + tap_max = 30; + break; + case MMC_TIMING_UHS_SDR50: + /* For 100MHz clock, 15 Taps are available */ + tap_max = 15; + break; + case MMC_TIMING_UHS_SDR104: + case MMC_TIMING_MMC_HS200: + /* For 200MHz clock, 8 Taps are available */ + tap_max = 8; + default: + break; + } + + tap_delay = (degrees * tap_max) / 360; + + /* Set the Clock Phase */ + ret = zynqmp_pm_set_sd_tapdelay(node_id, PM_TAPDELAY_OUTPUT, tap_delay); + if (ret) + pr_err("Error setting Output Tap Delay\n"); + + /* Release DLL Reset */ + zynqmp_pm_sd_dll_reset(node_id, PM_DLL_RESET_RELEASE); + + return ret; +} + +static const struct clk_ops zynqmp_sdcardclk_ops = { + .recalc_rate = sdhci_arasan_sdcardclk_recalc_rate, + .set_phase = sdhci_zynqmp_sdcardclk_set_phase, +}; + +/** + * sdhci_zynqmp_sampleclk_set_phase - Set the SD Input Clock Tap Delays + * + * @hw: Pointer to the hardware clock structure. + * @degrees: The clock phase shift between 0 - 359. + * + * Set the SD Input Clock Tap Delays for Input path + * + * Return: 0 on success and error value on error + */ +static int sdhci_zynqmp_sampleclk_set_phase(struct clk_hw *hw, int degrees) +{ + struct sdhci_arasan_clk_data *clk_data = + container_of(hw, struct sdhci_arasan_clk_data, sampleclk_hw); + struct sdhci_arasan_data *sdhci_arasan = + container_of(clk_data, struct sdhci_arasan_data, clk_data); + struct sdhci_host *host = sdhci_arasan->host; + const char *clk_name = clk_hw_get_name(hw); + u32 node_id = !strcmp(clk_name, "clk_in_sd0") ? NODE_SD_0 : NODE_SD_1; + u8 tap_delay, tap_max = 0; + int ret; + + /* This is applicable for SDHCI_SPEC_300 and above */ + if (host->version < SDHCI_SPEC_300) + return 0; + + /* Assert DLL Reset */ + zynqmp_pm_sd_dll_reset(node_id, PM_DLL_RESET_ASSERT); + + switch (host->timing) { + case MMC_TIMING_MMC_HS: + case MMC_TIMING_SD_HS: + case MMC_TIMING_UHS_SDR25: + case MMC_TIMING_UHS_DDR50: + case MMC_TIMING_MMC_DDR52: + /* For 50MHz clock, 120 Taps are available */ + tap_max = 120; + break; + case MMC_TIMING_UHS_SDR50: + /* For 100MHz clock, 60 Taps are available */ + tap_max = 60; + break; + case MMC_TIMING_UHS_SDR104: + case MMC_TIMING_MMC_HS200: + /* For 200MHz clock, 30 Taps are available */ + tap_max = 30; + default: + break; + } + + tap_delay = (degrees * tap_max) / 360; + + /* Set the Clock Phase */ + ret = zynqmp_pm_set_sd_tapdelay(node_id, PM_TAPDELAY_INPUT, tap_delay); + if (ret) + pr_err("Error setting Input Tap Delay\n"); + + return ret; +} + +static const struct clk_ops zynqmp_sampleclk_ops = { + .recalc_rate = sdhci_arasan_sampleclk_recalc_rate, + .set_phase = sdhci_zynqmp_sampleclk_set_phase, +}; + +/** + * sdhci_versal_sdcardclk_set_phase - Set the SD Output Clock Tap Delays + * + * @hw: Pointer to the hardware clock structure. + * @degrees: The clock phase shift between 0 - 359. + * + * Set the SD Output Clock Tap Delays for Output path + * + * Return: 0 on success and error value on error + */ +static int sdhci_versal_sdcardclk_set_phase(struct clk_hw *hw, int degrees) +{ + struct sdhci_arasan_clk_data *clk_data = + container_of(hw, struct sdhci_arasan_clk_data, sdcardclk_hw); + struct sdhci_arasan_data *sdhci_arasan = + container_of(clk_data, struct sdhci_arasan_data, clk_data); + struct sdhci_host *host = sdhci_arasan->host; + u8 tap_delay, tap_max = 0; + + /* This is applicable for SDHCI_SPEC_300 and above */ + if (host->version < SDHCI_SPEC_300) + return 0; + + switch (host->timing) { + case MMC_TIMING_MMC_HS: + case MMC_TIMING_SD_HS: + case MMC_TIMING_UHS_SDR25: + case MMC_TIMING_UHS_DDR50: + case MMC_TIMING_MMC_DDR52: + /* For 50MHz clock, 30 Taps are available */ + tap_max = 30; + break; + case MMC_TIMING_UHS_SDR50: + /* For 100MHz clock, 15 Taps are available */ + tap_max = 15; + break; + case MMC_TIMING_UHS_SDR104: + case MMC_TIMING_MMC_HS200: + /* For 200MHz clock, 8 Taps are available */ + tap_max = 8; + default: + break; + } + + tap_delay = (degrees * tap_max) / 360; + + /* Set the Clock Phase */ + if (tap_delay) { + u32 regval; + + regval = sdhci_readl(host, SDHCI_ARASAN_OTAPDLY_REGISTER); + regval |= SDHCI_OTAPDLY_ENABLE; + sdhci_writel(host, regval, SDHCI_ARASAN_OTAPDLY_REGISTER); + regval &= ~SDHCI_ARASAN_OTAPDLY_SEL_MASK; + regval |= tap_delay; + sdhci_writel(host, regval, SDHCI_ARASAN_OTAPDLY_REGISTER); + } + + return 0; +} + +static const struct clk_ops versal_sdcardclk_ops = { + .recalc_rate = sdhci_arasan_sdcardclk_recalc_rate, + .set_phase = sdhci_versal_sdcardclk_set_phase, +}; + +/** + * sdhci_versal_sampleclk_set_phase - Set the SD Input Clock Tap Delays + * + * @hw: Pointer to the hardware clock structure. + * @degrees: The clock phase shift between 0 - 359. + * + * Set the SD Input Clock Tap Delays for Input path + * + * Return: 0 on success and error value on error + */ +static int sdhci_versal_sampleclk_set_phase(struct clk_hw *hw, int degrees) +{ + struct sdhci_arasan_clk_data *clk_data = + container_of(hw, struct sdhci_arasan_clk_data, sampleclk_hw); + struct sdhci_arasan_data *sdhci_arasan = + container_of(clk_data, struct sdhci_arasan_data, clk_data); + struct sdhci_host *host = sdhci_arasan->host; + u8 tap_delay, tap_max = 0; + + /* This is applicable for SDHCI_SPEC_300 and above */ + if (host->version < SDHCI_SPEC_300) + return 0; + + switch (host->timing) { + case MMC_TIMING_MMC_HS: + case MMC_TIMING_SD_HS: + case MMC_TIMING_UHS_SDR25: + case MMC_TIMING_UHS_DDR50: + case MMC_TIMING_MMC_DDR52: + /* For 50MHz clock, 120 Taps are available */ + tap_max = 120; + break; + case MMC_TIMING_UHS_SDR50: + /* For 100MHz clock, 60 Taps are available */ + tap_max = 60; + break; + case MMC_TIMING_UHS_SDR104: + case MMC_TIMING_MMC_HS200: + /* For 200MHz clock, 30 Taps are available */ + tap_max = 30; + default: + break; + } + + tap_delay = (degrees * tap_max) / 360; + + /* Set the Clock Phase */ + if (tap_delay) { + u32 regval; + + regval = sdhci_readl(host, SDHCI_ARASAN_ITAPDLY_REGISTER); + regval |= SDHCI_ITAPDLY_CHGWIN; + sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER); + regval |= SDHCI_ITAPDLY_ENABLE; + sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER); + regval &= ~SDHCI_ARASAN_ITAPDLY_SEL_MASK; + regval |= tap_delay; + sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER); + regval &= ~SDHCI_ITAPDLY_CHGWIN; + sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER); + } + + return 0; +} + +static const struct clk_ops versal_sampleclk_ops = { + .recalc_rate = sdhci_arasan_sampleclk_recalc_rate, + .set_phase = sdhci_versal_sampleclk_set_phase, +}; + +static void arasan_zynqmp_dll_reset(struct sdhci_host *host, u32 deviceid) +{ + u16 clk; + + clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL); + clk &= ~(SDHCI_CLOCK_CARD_EN | SDHCI_CLOCK_INT_EN); + sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL); + + /* Issue DLL Reset */ + zynqmp_pm_sd_dll_reset(deviceid, PM_DLL_RESET_PULSE); + + clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL); + + sdhci_enable_clk(host, clk); +} + +static int arasan_zynqmp_execute_tuning(struct mmc_host *mmc, u32 opcode) +{ + struct sdhci_host *host = mmc_priv(mmc); + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host); + struct clk_hw *hw = &sdhci_arasan->clk_data.sdcardclk_hw; + const char *clk_name = clk_hw_get_name(hw); + u32 device_id = !strcmp(clk_name, "clk_out_sd0") ? NODE_SD_0 : + NODE_SD_1; + int err; + + arasan_zynqmp_dll_reset(host, device_id); + + err = sdhci_execute_tuning(mmc, opcode); + if (err) + return err; + + arasan_zynqmp_dll_reset(host, device_id); + + return 0; +} + +/** + * sdhci_arasan_update_clockmultiplier - Set corecfg_clockmultiplier + * + * @host: The sdhci_host + * @value: The value to write + * + * The corecfg_clockmultiplier is supposed to contain clock multiplier + * value of programmable clock generator. + * + * NOTES: + * - Many existing devices don't seem to do this and work fine. To keep + * compatibility for old hardware where the device tree doesn't provide a + * register map, this function is a noop if a soc_ctl_map hasn't been provided + * for this platform. + * - The value of corecfg_clockmultiplier should sync with that of corresponding + * value reading from sdhci_capability_register. So this function is called + * once at probe time and never called again. + */ +static void sdhci_arasan_update_clockmultiplier(struct sdhci_host *host, + u32 value) +{ + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host); + const struct sdhci_arasan_soc_ctl_map *soc_ctl_map = + sdhci_arasan->soc_ctl_map; + + /* Having a map is optional */ + if (!soc_ctl_map) + return; + + /* If we have a map, we expect to have a syscon */ + if (!sdhci_arasan->soc_ctl_base) { + pr_warn("%s: Have regmap, but no soc-ctl-syscon\n", + mmc_hostname(host->mmc)); + return; + } + + sdhci_arasan_syscon_write(host, &soc_ctl_map->clockmultiplier, value); +} + +/** + * sdhci_arasan_update_baseclkfreq - Set corecfg_baseclkfreq + * + * @host: The sdhci_host + * + * The corecfg_baseclkfreq is supposed to contain the MHz of clk_xin. This + * function can be used to make that happen. + * + * NOTES: + * - Many existing devices don't seem to do this and work fine. To keep + * compatibility for old hardware where the device tree doesn't provide a + * register map, this function is a noop if a soc_ctl_map hasn't been provided + * for this platform. + * - It's assumed that clk_xin is not dynamic and that we use the SDHCI divider + * to achieve lower clock rates. That means that this function is called once + * at probe time and never called again. + */ +static void sdhci_arasan_update_baseclkfreq(struct sdhci_host *host) +{ + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host); + const struct sdhci_arasan_soc_ctl_map *soc_ctl_map = + sdhci_arasan->soc_ctl_map; + u32 mhz = DIV_ROUND_CLOSEST(clk_get_rate(pltfm_host->clk), 1000000); + + /* Having a map is optional */ + if (!soc_ctl_map) + return; + + /* If we have a map, we expect to have a syscon */ + if (!sdhci_arasan->soc_ctl_base) { + pr_warn("%s: Have regmap, but no soc-ctl-syscon\n", + mmc_hostname(host->mmc)); + return; + } + + sdhci_arasan_syscon_write(host, &soc_ctl_map->baseclkfreq, mhz); +} + +static void sdhci_arasan_set_clk_delays(struct sdhci_host *host) +{ + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host); + struct sdhci_arasan_clk_data *clk_data = &sdhci_arasan->clk_data; + + clk_set_phase(clk_data->sampleclk, + clk_data->clk_phase_in[host->timing]); + clk_set_phase(clk_data->sdcardclk, + clk_data->clk_phase_out[host->timing]); +} + +static void arasan_dt_read_clk_phase(struct device *dev, + struct sdhci_arasan_clk_data *clk_data, + unsigned int timing, const char *prop) +{ + struct device_node *np = dev->of_node; + + int clk_phase[2] = {0}; + + /* + * Read Tap Delay values from DT, if the DT does not contain the + * Tap Values then use the pre-defined values. + */ + if (of_property_read_variable_u32_array(np, prop, &clk_phase[0], + 2, 0)) { + dev_dbg(dev, "Using predefined clock phase for %s = %d %d\n", + prop, clk_data->clk_phase_in[timing], + clk_data->clk_phase_out[timing]); + return; + } + + /* The values read are Input and Output Clock Delays in order */ + clk_data->clk_phase_in[timing] = clk_phase[0]; + clk_data->clk_phase_out[timing] = clk_phase[1]; +} + +/** + * arasan_dt_parse_clk_phases - Read Clock Delay values from DT + * + * @dev: Pointer to our struct device. + * @clk_data: Pointer to the Clock Data structure + * + * Called at initialization to parse the values of Clock Delays. + */ +static void arasan_dt_parse_clk_phases(struct device *dev, + struct sdhci_arasan_clk_data *clk_data) +{ + u32 mio_bank = 0; + int i; + + /* + * This has been kept as a pointer and is assigned a function here. + * So that different controller variants can assign their own handling + * function. + */ + clk_data->set_clk_delays = sdhci_arasan_set_clk_delays; + + if (of_device_is_compatible(dev->of_node, "xlnx,zynqmp-8.9a")) { + u32 zynqmp_iclk_phase[MMC_TIMING_MMC_HS400 + 1] = + ZYNQMP_ICLK_PHASE; + u32 zynqmp_oclk_phase[MMC_TIMING_MMC_HS400 + 1] = + ZYNQMP_OCLK_PHASE; + + of_property_read_u32(dev->of_node, "xlnx,mio-bank", &mio_bank); + if (mio_bank == 2) { + zynqmp_oclk_phase[MMC_TIMING_UHS_SDR104] = 90; + zynqmp_oclk_phase[MMC_TIMING_MMC_HS200] = 90; + } + + for (i = 0; i <= MMC_TIMING_MMC_HS400; i++) { + clk_data->clk_phase_in[i] = zynqmp_iclk_phase[i]; + clk_data->clk_phase_out[i] = zynqmp_oclk_phase[i]; + } + } + + if (of_device_is_compatible(dev->of_node, "xlnx,versal-8.9a")) { + u32 versal_iclk_phase[MMC_TIMING_MMC_HS400 + 1] = + VERSAL_ICLK_PHASE; + u32 versal_oclk_phase[MMC_TIMING_MMC_HS400 + 1] = + VERSAL_OCLK_PHASE; + + for (i = 0; i <= MMC_TIMING_MMC_HS400; i++) { + clk_data->clk_phase_in[i] = versal_iclk_phase[i]; + clk_data->clk_phase_out[i] = versal_oclk_phase[i]; + } + } + + arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_LEGACY, + "clk-phase-legacy"); + arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_MMC_HS, + "clk-phase-mmc-hs"); + arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_SD_HS, + "clk-phase-sd-hs"); + arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_UHS_SDR12, + "clk-phase-uhs-sdr12"); + arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_UHS_SDR25, + "clk-phase-uhs-sdr25"); + arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_UHS_SDR50, + "clk-phase-uhs-sdr50"); + arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_UHS_SDR104, + "clk-phase-uhs-sdr104"); + arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_UHS_DDR50, + "clk-phase-uhs-ddr50"); + arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_MMC_DDR52, + "clk-phase-mmc-ddr52"); + arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_MMC_HS200, + "clk-phase-mmc-hs200"); + arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_MMC_HS400, + "clk-phase-mmc-hs400"); +} + +static const struct sdhci_pltfm_data sdhci_arasan_pdata = { + .ops = &sdhci_arasan_ops, + .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN, + .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN | + SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN | + SDHCI_QUIRK2_STOP_WITH_TC, +}; + +static const struct sdhci_arasan_clk_ops arasan_clk_ops = { + .sdcardclk_ops = &arasan_sdcardclk_ops, + .sampleclk_ops = &arasan_sampleclk_ops, +}; + +static struct sdhci_arasan_of_data sdhci_arasan_generic_data = { + .pdata = &sdhci_arasan_pdata, + .clk_ops = &arasan_clk_ops, +}; + +static const struct sdhci_pltfm_data sdhci_keembay_emmc_pdata = { + .ops = &sdhci_arasan_cqe_ops, + .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN | + SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC | + SDHCI_QUIRK_NO_LED | + SDHCI_QUIRK_32BIT_DMA_ADDR | + SDHCI_QUIRK_32BIT_DMA_SIZE | + SDHCI_QUIRK_32BIT_ADMA_SIZE, + .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN | + SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN | + SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 | + SDHCI_QUIRK2_STOP_WITH_TC | + SDHCI_QUIRK2_BROKEN_64_BIT_DMA, +}; + +static const struct sdhci_pltfm_data sdhci_keembay_sd_pdata = { + .ops = &sdhci_arasan_ops, + .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN | + SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC | + SDHCI_QUIRK_NO_LED | + SDHCI_QUIRK_32BIT_DMA_ADDR | + SDHCI_QUIRK_32BIT_DMA_SIZE | + SDHCI_QUIRK_32BIT_ADMA_SIZE, + .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN | + SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN | + SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON | + SDHCI_QUIRK2_STOP_WITH_TC | + SDHCI_QUIRK2_BROKEN_64_BIT_DMA, +}; + +static const struct sdhci_pltfm_data sdhci_keembay_sdio_pdata = { + .ops = &sdhci_arasan_ops, + .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN | + SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC | + SDHCI_QUIRK_NO_LED | + SDHCI_QUIRK_32BIT_DMA_ADDR | + SDHCI_QUIRK_32BIT_DMA_SIZE | + SDHCI_QUIRK_32BIT_ADMA_SIZE, + .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN | + SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN | + SDHCI_QUIRK2_HOST_OFF_CARD_ON | + SDHCI_QUIRK2_BROKEN_64_BIT_DMA, +}; + +static struct sdhci_arasan_of_data sdhci_arasan_rk3399_data = { + .soc_ctl_map = &rk3399_soc_ctl_map, + .pdata = &sdhci_arasan_cqe_pdata, + .clk_ops = &arasan_clk_ops, +}; + +static struct sdhci_arasan_of_data intel_lgm_emmc_data = { + .soc_ctl_map = &intel_lgm_emmc_soc_ctl_map, + .pdata = &sdhci_arasan_cqe_pdata, + .clk_ops = &arasan_clk_ops, +}; + +static struct sdhci_arasan_of_data intel_lgm_sdxc_data = { + .soc_ctl_map = &intel_lgm_sdxc_soc_ctl_map, + .pdata = &sdhci_arasan_cqe_pdata, + .clk_ops = &arasan_clk_ops, +}; + +static const struct sdhci_pltfm_data sdhci_arasan_zynqmp_pdata = { + .ops = &sdhci_arasan_ops, + .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN | + SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN | + SDHCI_QUIRK2_STOP_WITH_TC, +}; + +static const struct sdhci_arasan_clk_ops zynqmp_clk_ops = { + .sdcardclk_ops = &zynqmp_sdcardclk_ops, + .sampleclk_ops = &zynqmp_sampleclk_ops, +}; + +static struct sdhci_arasan_of_data sdhci_arasan_zynqmp_data = { + .pdata = &sdhci_arasan_zynqmp_pdata, + .clk_ops = &zynqmp_clk_ops, +}; + +static const struct sdhci_arasan_clk_ops versal_clk_ops = { + .sdcardclk_ops = &versal_sdcardclk_ops, + .sampleclk_ops = &versal_sampleclk_ops, +}; + +static struct sdhci_arasan_of_data sdhci_arasan_versal_data = { + .pdata = &sdhci_arasan_zynqmp_pdata, + .clk_ops = &versal_clk_ops, +}; + +static struct sdhci_arasan_of_data intel_keembay_emmc_data = { + .soc_ctl_map = &intel_keembay_soc_ctl_map, + .pdata = &sdhci_keembay_emmc_pdata, + .clk_ops = &arasan_clk_ops, +}; + +static struct sdhci_arasan_of_data intel_keembay_sd_data = { + .soc_ctl_map = &intel_keembay_soc_ctl_map, + .pdata = &sdhci_keembay_sd_pdata, + .clk_ops = &arasan_clk_ops, +}; + +static struct sdhci_arasan_of_data intel_keembay_sdio_data = { + .soc_ctl_map = &intel_keembay_soc_ctl_map, + .pdata = &sdhci_keembay_sdio_pdata, + .clk_ops = &arasan_clk_ops, +}; + +static const struct of_device_id sdhci_arasan_of_match[] = { + /* SoC-specific compatible strings w/ soc_ctl_map */ + { + .compatible = "rockchip,rk3399-sdhci-5.1", + .data = &sdhci_arasan_rk3399_data, + }, + { + .compatible = "intel,lgm-sdhci-5.1-emmc", + .data = &intel_lgm_emmc_data, + }, + { + .compatible = "intel,lgm-sdhci-5.1-sdxc", + .data = &intel_lgm_sdxc_data, + }, + { + .compatible = "intel,keembay-sdhci-5.1-emmc", + .data = &intel_keembay_emmc_data, + }, + { + .compatible = "intel,keembay-sdhci-5.1-sd", + .data = &intel_keembay_sd_data, + }, + { + .compatible = "intel,keembay-sdhci-5.1-sdio", + .data = &intel_keembay_sdio_data, + }, + /* Generic compatible below here */ + { + .compatible = "arasan,sdhci-8.9a", + .data = &sdhci_arasan_generic_data, + }, + { + .compatible = "arasan,sdhci-5.1", + .data = &sdhci_arasan_generic_data, + }, + { + .compatible = "arasan,sdhci-4.9a", + .data = &sdhci_arasan_generic_data, + }, + { + .compatible = "xlnx,zynqmp-8.9a", + .data = &sdhci_arasan_zynqmp_data, + }, + { + .compatible = "xlnx,versal-8.9a", + .data = &sdhci_arasan_versal_data, + }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, sdhci_arasan_of_match); + +/** + * sdhci_arasan_register_sdcardclk - Register the sdcardclk for a PHY to use + * + * @sdhci_arasan: Our private data structure. + * @clk_xin: Pointer to the functional clock + * @dev: Pointer to our struct device. + * + * Some PHY devices need to know what the actual card clock is. In order for + * them to find out, we'll provide a clock through the common clock framework + * for them to query. + * + * Return: 0 on success and error value on error + */ +static int +sdhci_arasan_register_sdcardclk(struct sdhci_arasan_data *sdhci_arasan, + struct clk *clk_xin, + struct device *dev) +{ + struct sdhci_arasan_clk_data *clk_data = &sdhci_arasan->clk_data; + struct device_node *np = dev->of_node; + struct clk_init_data sdcardclk_init; + const char *parent_clk_name; + int ret; + + ret = of_property_read_string_index(np, "clock-output-names", 0, + &sdcardclk_init.name); + if (ret) { + dev_err(dev, "DT has #clock-cells but no clock-output-names\n"); + return ret; + } + + parent_clk_name = __clk_get_name(clk_xin); + sdcardclk_init.parent_names = &parent_clk_name; + sdcardclk_init.num_parents = 1; + sdcardclk_init.flags = CLK_GET_RATE_NOCACHE; + sdcardclk_init.ops = sdhci_arasan->clk_ops->sdcardclk_ops; + + clk_data->sdcardclk_hw.init = &sdcardclk_init; + clk_data->sdcardclk = + devm_clk_register(dev, &clk_data->sdcardclk_hw); + if (IS_ERR(clk_data->sdcardclk)) + return PTR_ERR(clk_data->sdcardclk); + clk_data->sdcardclk_hw.init = NULL; + + ret = of_clk_add_provider(np, of_clk_src_simple_get, + clk_data->sdcardclk); + if (ret) + dev_err(dev, "Failed to add sdcard clock provider\n"); + + return ret; +} + +/** + * sdhci_arasan_register_sampleclk - Register the sampleclk for a PHY to use + * + * @sdhci_arasan: Our private data structure. + * @clk_xin: Pointer to the functional clock + * @dev: Pointer to our struct device. + * + * Some PHY devices need to know what the actual card clock is. In order for + * them to find out, we'll provide a clock through the common clock framework + * for them to query. + * + * Return: 0 on success and error value on error + */ +static int +sdhci_arasan_register_sampleclk(struct sdhci_arasan_data *sdhci_arasan, + struct clk *clk_xin, + struct device *dev) +{ + struct sdhci_arasan_clk_data *clk_data = &sdhci_arasan->clk_data; + struct device_node *np = dev->of_node; + struct clk_init_data sampleclk_init; + const char *parent_clk_name; + int ret; + + ret = of_property_read_string_index(np, "clock-output-names", 1, + &sampleclk_init.name); + if (ret) { + dev_err(dev, "DT has #clock-cells but no clock-output-names\n"); + return ret; + } + + parent_clk_name = __clk_get_name(clk_xin); + sampleclk_init.parent_names = &parent_clk_name; + sampleclk_init.num_parents = 1; + sampleclk_init.flags = CLK_GET_RATE_NOCACHE; + sampleclk_init.ops = sdhci_arasan->clk_ops->sampleclk_ops; + + clk_data->sampleclk_hw.init = &sampleclk_init; + clk_data->sampleclk = + devm_clk_register(dev, &clk_data->sampleclk_hw); + if (IS_ERR(clk_data->sampleclk)) + return PTR_ERR(clk_data->sampleclk); + clk_data->sampleclk_hw.init = NULL; + + ret = of_clk_add_provider(np, of_clk_src_simple_get, + clk_data->sampleclk); + if (ret) + dev_err(dev, "Failed to add sample clock provider\n"); + + return ret; +} + +/** + * sdhci_arasan_unregister_sdclk - Undoes sdhci_arasan_register_sdclk() + * + * @dev: Pointer to our struct device. + * + * Should be called any time we're exiting and sdhci_arasan_register_sdclk() + * returned success. + */ +static void sdhci_arasan_unregister_sdclk(struct device *dev) +{ + struct device_node *np = dev->of_node; + + if (!of_find_property(np, "#clock-cells", NULL)) + return; + + of_clk_del_provider(dev->of_node); +} + +/** + * sdhci_arasan_update_support64b - Set SUPPORT_64B (64-bit System Bus Support) + * + * This should be set based on the System Address Bus. + * 0: the Core supports only 32-bit System Address Bus. + * 1: the Core supports 64-bit System Address Bus. + * + * NOTES: + * - For Keem Bay, it is required to clear this bit. Its default value is 1'b1. + * Keem Bay does not support 64-bit access. + * + * @host: The sdhci_host + * @value: The value to write + */ +static void sdhci_arasan_update_support64b(struct sdhci_host *host, u32 value) +{ + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host); + const struct sdhci_arasan_soc_ctl_map *soc_ctl_map = + sdhci_arasan->soc_ctl_map; + + /* Having a map is optional */ + if (!soc_ctl_map) + return; + + /* If we have a map, we expect to have a syscon */ + if (!sdhci_arasan->soc_ctl_base) { + pr_warn("%s: Have regmap, but no soc-ctl-syscon\n", + mmc_hostname(host->mmc)); + return; + } + + sdhci_arasan_syscon_write(host, &soc_ctl_map->support64b, value); +} + +/** + * sdhci_arasan_register_sdclk - Register the sdcardclk for a PHY to use + * + * @sdhci_arasan: Our private data structure. + * @clk_xin: Pointer to the functional clock + * @dev: Pointer to our struct device. + * + * Some PHY devices need to know what the actual card clock is. In order for + * them to find out, we'll provide a clock through the common clock framework + * for them to query. + * + * Note: without seriously re-architecting SDHCI's clock code and testing on + * all platforms, there's no way to create a totally beautiful clock here + * with all clock ops implemented. Instead, we'll just create a clock that can + * be queried and set the CLK_GET_RATE_NOCACHE attribute to tell common clock + * framework that we're doing things behind its back. This should be sufficient + * to create nice clean device tree bindings and later (if needed) we can try + * re-architecting SDHCI if we see some benefit to it. + * + * Return: 0 on success and error value on error + */ +static int sdhci_arasan_register_sdclk(struct sdhci_arasan_data *sdhci_arasan, + struct clk *clk_xin, + struct device *dev) +{ + struct device_node *np = dev->of_node; + u32 num_clks = 0; + int ret; + + /* Providing a clock to the PHY is optional; no error if missing */ + if (of_property_read_u32(np, "#clock-cells", &num_clks) < 0) + return 0; + + ret = sdhci_arasan_register_sdcardclk(sdhci_arasan, clk_xin, dev); + if (ret) + return ret; + + if (num_clks) { + ret = sdhci_arasan_register_sampleclk(sdhci_arasan, clk_xin, + dev); + if (ret) { + sdhci_arasan_unregister_sdclk(dev); + return ret; + } + } + + return 0; +} + +static int sdhci_arasan_add_host(struct sdhci_arasan_data *sdhci_arasan) +{ + struct sdhci_host *host = sdhci_arasan->host; + struct cqhci_host *cq_host; + bool dma64; + int ret; + + if (!sdhci_arasan->has_cqe) + return sdhci_add_host(host); + + ret = sdhci_setup_host(host); + if (ret) + return ret; + + cq_host = devm_kzalloc(host->mmc->parent, + sizeof(*cq_host), GFP_KERNEL); + if (!cq_host) { + ret = -ENOMEM; + goto cleanup; + } + + cq_host->mmio = host->ioaddr + SDHCI_ARASAN_CQE_BASE_ADDR; + cq_host->ops = &sdhci_arasan_cqhci_ops; + + dma64 = host->flags & SDHCI_USE_64_BIT_DMA; + if (dma64) + cq_host->caps |= CQHCI_TASK_DESC_SZ_128; + + ret = cqhci_init(cq_host, host->mmc, dma64); + if (ret) + goto cleanup; + + ret = __sdhci_add_host(host); + if (ret) + goto cleanup; + + return 0; + +cleanup: + sdhci_cleanup_host(host); + return ret; +} + +static int sdhci_arasan_probe(struct platform_device *pdev) +{ + int ret; + const struct of_device_id *match; + struct device_node *node; + struct clk *clk_xin; + struct sdhci_host *host; + struct sdhci_pltfm_host *pltfm_host; + struct sdhci_arasan_data *sdhci_arasan; + struct device_node *np = pdev->dev.of_node; + const struct sdhci_arasan_of_data *data; + + match = of_match_node(sdhci_arasan_of_match, pdev->dev.of_node); + data = match->data; + host = sdhci_pltfm_init(pdev, data->pdata, sizeof(*sdhci_arasan)); + + if (IS_ERR(host)) + return PTR_ERR(host); + + pltfm_host = sdhci_priv(host); + sdhci_arasan = sdhci_pltfm_priv(pltfm_host); + sdhci_arasan->host = host; + + sdhci_arasan->soc_ctl_map = data->soc_ctl_map; + sdhci_arasan->clk_ops = data->clk_ops; + + node = of_parse_phandle(pdev->dev.of_node, "arasan,soc-ctl-syscon", 0); + if (node) { + sdhci_arasan->soc_ctl_base = syscon_node_to_regmap(node); + of_node_put(node); + + if (IS_ERR(sdhci_arasan->soc_ctl_base)) { + ret = dev_err_probe(&pdev->dev, + PTR_ERR(sdhci_arasan->soc_ctl_base), + "Can't get syscon\n"); + goto err_pltfm_free; + } + } + + sdhci_arasan->clk_ahb = devm_clk_get(&pdev->dev, "clk_ahb"); + if (IS_ERR(sdhci_arasan->clk_ahb)) { + dev_err(&pdev->dev, "clk_ahb clock not found.\n"); + ret = PTR_ERR(sdhci_arasan->clk_ahb); + goto err_pltfm_free; + } + + clk_xin = devm_clk_get(&pdev->dev, "clk_xin"); + if (IS_ERR(clk_xin)) { + dev_err(&pdev->dev, "clk_xin clock not found.\n"); + ret = PTR_ERR(clk_xin); + goto err_pltfm_free; + } + + ret = clk_prepare_enable(sdhci_arasan->clk_ahb); + if (ret) { + dev_err(&pdev->dev, "Unable to enable AHB clock.\n"); + goto err_pltfm_free; + } + + ret = clk_prepare_enable(clk_xin); + if (ret) { + dev_err(&pdev->dev, "Unable to enable SD clock.\n"); + goto clk_dis_ahb; + } + + sdhci_get_of_property(pdev); + + if (of_property_read_bool(np, "xlnx,fails-without-test-cd")) + sdhci_arasan->quirks |= SDHCI_ARASAN_QUIRK_FORCE_CDTEST; + + if (of_property_read_bool(np, "xlnx,int-clock-stable-broken")) + sdhci_arasan->quirks |= SDHCI_ARASAN_QUIRK_CLOCK_UNSTABLE; + + pltfm_host->clk = clk_xin; + + if (of_device_is_compatible(pdev->dev.of_node, + "rockchip,rk3399-sdhci-5.1")) + sdhci_arasan_update_clockmultiplier(host, 0x0); + + if (of_device_is_compatible(np, "intel,keembay-sdhci-5.1-emmc") || + of_device_is_compatible(np, "intel,keembay-sdhci-5.1-sd") || + of_device_is_compatible(np, "intel,keembay-sdhci-5.1-sdio")) { + sdhci_arasan_update_clockmultiplier(host, 0x0); + sdhci_arasan_update_support64b(host, 0x0); + + host->mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY; + } + + sdhci_arasan_update_baseclkfreq(host); + + ret = sdhci_arasan_register_sdclk(sdhci_arasan, clk_xin, &pdev->dev); + if (ret) + goto clk_disable_all; + + if (of_device_is_compatible(np, "xlnx,zynqmp-8.9a")) { + host->mmc_host_ops.execute_tuning = + arasan_zynqmp_execute_tuning; + + sdhci_arasan->quirks |= SDHCI_ARASAN_QUIRK_CLOCK_25_BROKEN; + } + + arasan_dt_parse_clk_phases(&pdev->dev, &sdhci_arasan->clk_data); + + ret = mmc_of_parse(host->mmc); + if (ret) { + if (ret != -EPROBE_DEFER) + dev_err(&pdev->dev, "parsing dt failed (%d)\n", ret); + goto unreg_clk; + } + + sdhci_arasan->phy = ERR_PTR(-ENODEV); + if (of_device_is_compatible(pdev->dev.of_node, + "arasan,sdhci-5.1")) { + sdhci_arasan->phy = devm_phy_get(&pdev->dev, + "phy_arasan"); + if (IS_ERR(sdhci_arasan->phy)) { + ret = PTR_ERR(sdhci_arasan->phy); + dev_err(&pdev->dev, "No phy for arasan,sdhci-5.1.\n"); + goto unreg_clk; + } + + ret = phy_init(sdhci_arasan->phy); + if (ret < 0) { + dev_err(&pdev->dev, "phy_init err.\n"); + goto unreg_clk; + } + + host->mmc_host_ops.hs400_enhanced_strobe = + sdhci_arasan_hs400_enhanced_strobe; + host->mmc_host_ops.start_signal_voltage_switch = + sdhci_arasan_voltage_switch; + sdhci_arasan->has_cqe = true; + host->mmc->caps2 |= MMC_CAP2_CQE; + + if (!of_property_read_bool(np, "disable-cqe-dcmd")) + host->mmc->caps2 |= MMC_CAP2_CQE_DCMD; + } + + ret = sdhci_arasan_add_host(sdhci_arasan); + if (ret) + goto err_add_host; + + return 0; + +err_add_host: + if (!IS_ERR(sdhci_arasan->phy)) + phy_exit(sdhci_arasan->phy); +unreg_clk: + sdhci_arasan_unregister_sdclk(&pdev->dev); +clk_disable_all: + clk_disable_unprepare(clk_xin); +clk_dis_ahb: + clk_disable_unprepare(sdhci_arasan->clk_ahb); +err_pltfm_free: + sdhci_pltfm_free(pdev); + return ret; +} + +static int sdhci_arasan_remove(struct platform_device *pdev) +{ + int ret; + struct sdhci_host *host = platform_get_drvdata(pdev); + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host); + struct clk *clk_ahb = sdhci_arasan->clk_ahb; + + if (!IS_ERR(sdhci_arasan->phy)) { + if (sdhci_arasan->is_phy_on) + phy_power_off(sdhci_arasan->phy); + phy_exit(sdhci_arasan->phy); + } + + sdhci_arasan_unregister_sdclk(&pdev->dev); + + ret = sdhci_pltfm_unregister(pdev); + + clk_disable_unprepare(clk_ahb); + + return ret; +} + +static struct platform_driver sdhci_arasan_driver = { + .driver = { + .name = "sdhci-arasan", + .probe_type = PROBE_PREFER_ASYNCHRONOUS, + .of_match_table = sdhci_arasan_of_match, + .pm = &sdhci_arasan_dev_pm_ops, + }, + .probe = sdhci_arasan_probe, + .remove = sdhci_arasan_remove, +}; + +module_platform_driver(sdhci_arasan_driver); + +MODULE_DESCRIPTION("Driver for the Arasan SDHCI Controller"); +MODULE_AUTHOR("Soeren Brinkmann <soren.brinkmann@xilinx.com>"); +MODULE_LICENSE("GPL"); |