diff options
Diffstat (limited to 'drivers/scsi/aic7xxx')
51 files changed, 57982 insertions, 0 deletions
diff --git a/drivers/scsi/aic7xxx/.gitignore b/drivers/scsi/aic7xxx/.gitignore new file mode 100644 index 000000000..9aa780221 --- /dev/null +++ b/drivers/scsi/aic7xxx/.gitignore @@ -0,0 +1,7 @@ +# SPDX-License-Identifier: GPL-2.0-only +aic79xx_reg.h +aic79xx_reg_print.c +aic79xx_seq.h +aic7xxx_reg.h +aic7xxx_reg_print.c +aic7xxx_seq.h diff --git a/drivers/scsi/aic7xxx/Kconfig.aic79xx b/drivers/scsi/aic7xxx/Kconfig.aic79xx new file mode 100644 index 000000000..a47dbd500 --- /dev/null +++ b/drivers/scsi/aic7xxx/Kconfig.aic79xx @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: GPL-2.0-only +# +# AIC79XX 2.5.X Kernel configuration File. +# $Id: //depot/linux-aic79xx-2.5.0/drivers/scsi/aic7xxx/Kconfig.aic79xx#4 $ +# +config SCSI_AIC79XX + tristate "Adaptec AIC79xx U320 support" + depends on PCI && SCSI + select SCSI_SPI_ATTRS + help + This driver supports all of Adaptec's Ultra 320 PCI-X + based SCSI controllers. + +config AIC79XX_CMDS_PER_DEVICE + int "Maximum number of TCQ commands per device" + depends on SCSI_AIC79XX + default "32" + help + Specify the number of commands you would like to allocate per SCSI + device when Tagged Command Queueing (TCQ) is enabled on that device. + + This is an upper bound value for the number of tagged transactions + to be used for any device. The aic7xxx driver will automatically + vary this number based on device behavior. For devices with a + fixed maximum, the driver will eventually lock to this maximum + and display a console message indicating this value. + + Due to resource allocation issues in the Linux SCSI mid-layer, using + a high number of commands per device may result in memory allocation + failures when many devices are attached to the system. For this reason, + the default is set to 32. Higher values may result in higher performance + on some devices. The upper bound is 253. 0 disables tagged queueing. + + Per device tag depth can be controlled via the kernel command line + "tag_info" option. See Documentation/scsi/aic79xx.rst for details. + +config AIC79XX_RESET_DELAY_MS + int "Initial bus reset delay in milli-seconds" + depends on SCSI_AIC79XX + default "5000" + help + The number of milliseconds to delay after an initial bus reset. + The bus settle delay following all error recovery actions is + dictated by the SCSI layer and is not affected by this value. + + Default: 5000 (5 seconds) + +config AIC79XX_BUILD_FIRMWARE + bool "Build Adapter Firmware with Kernel Build" + depends on SCSI_AIC79XX && !PREVENT_FIRMWARE_BUILD + help + This option should only be enabled if you are modifying the firmware + source to the aic79xx driver and wish to have the generated firmware + include files updated during a normal kernel build. The assembler + for the firmware requires lex and yacc or their equivalents, as well + as the db v1 library. You may have to install additional packages + or modify the assembler Makefile or the files it includes if your + build environment is different than that of the author. + +config AIC79XX_DEBUG_ENABLE + bool "Compile in Debugging Code" + depends on SCSI_AIC79XX + default y + help + Compile in aic79xx debugging code that can be useful in diagnosing + driver errors. + +config AIC79XX_DEBUG_MASK + int "Debug code enable mask (16383 for all debugging)" + depends on SCSI_AIC79XX + default "0" + help + Bit mask of debug options that is only valid if the + CONFIG_AIC79XX_DEBUG_ENABLE option is enabled. The bits in this mask + are defined in the drivers/scsi/aic7xxx/aic79xx.h - search for the + variable ahd_debug in that file to find them. + +config AIC79XX_REG_PRETTY_PRINT + bool "Decode registers during diagnostics" + depends on SCSI_AIC79XX + default y + help + Compile in register value tables for the output of expanded register + contents in diagnostics. This make it much easier to understand debug + output without having to refer to a data book and/or the aic7xxx.reg + file. diff --git a/drivers/scsi/aic7xxx/Kconfig.aic7xxx b/drivers/scsi/aic7xxx/Kconfig.aic7xxx new file mode 100644 index 000000000..0cfd92ce7 --- /dev/null +++ b/drivers/scsi/aic7xxx/Kconfig.aic7xxx @@ -0,0 +1,91 @@ +# SPDX-License-Identifier: GPL-2.0-only +# +# AIC7XXX and AIC79XX 2.5.X Kernel configuration File. +# $Id: //depot/linux-aic79xx-2.5.0/drivers/scsi/aic7xxx/Kconfig.aic7xxx#7 $ +# +config SCSI_AIC7XXX + tristate "Adaptec AIC7xxx Fast -> U160 support" + depends on (PCI || EISA) && SCSI + select SCSI_SPI_ATTRS + help + This driver supports all of Adaptec's Fast through Ultra 160 PCI + based SCSI controllers as well as the aic7770 based EISA and VLB + SCSI controllers (the 274x and 284x series). For AAA and ARO based + configurations, only SCSI functionality is provided. + + To compile this driver as a module, choose M here: the + module will be called aic7xxx. + +config AIC7XXX_CMDS_PER_DEVICE + int "Maximum number of TCQ commands per device" + depends on SCSI_AIC7XXX + default "32" + help + Specify the number of commands you would like to allocate per SCSI + device when Tagged Command Queueing (TCQ) is enabled on that device. + + This is an upper bound value for the number of tagged transactions + to be used for any device. The aic7xxx driver will automatically + vary this number based on device behavior. For devices with a + fixed maximum, the driver will eventually lock to this maximum + and display a console message indicating this value. + + Due to resource allocation issues in the Linux SCSI mid-layer, using + a high number of commands per device may result in memory allocation + failures when many devices are attached to the system. For this reason, + the default is set to 32. Higher values may result in higher performance + on some devices. The upper bound is 253. 0 disables tagged queueing. + + Per device tag depth can be controlled via the kernel command line + "tag_info" option. See Documentation/scsi/aic7xxx.rst for details. + +config AIC7XXX_RESET_DELAY_MS + int "Initial bus reset delay in milli-seconds" + depends on SCSI_AIC7XXX + default "5000" + help + The number of milliseconds to delay after an initial bus reset. + The bus settle delay following all error recovery actions is + dictated by the SCSI layer and is not affected by this value. + + Default: 5000 (5 seconds) + +config AIC7XXX_BUILD_FIRMWARE + bool "Build Adapter Firmware with Kernel Build" + depends on SCSI_AIC7XXX && !PREVENT_FIRMWARE_BUILD + help + This option should only be enabled if you are modifying the firmware + source to the aic7xxx driver and wish to have the generated firmware + include files updated during a normal kernel build. The assembler + for the firmware requires lex and yacc or their equivalents, as well + as the db v1 library. You may have to install additional packages + or modify the assembler Makefile or the files it includes if your + build environment is different than that of the author. + +config AIC7XXX_DEBUG_ENABLE + bool "Compile in Debugging Code" + depends on SCSI_AIC7XXX + default y + help + Compile in aic7xxx debugging code that can be useful in diagnosing + driver errors. + +config AIC7XXX_DEBUG_MASK + int "Debug code enable mask (2047 for all debugging)" + depends on SCSI_AIC7XXX + default "0" + help + Bit mask of debug options that is only valid if the + CONFIG_AIC7XXX_DEBUG_ENABLE option is enabled. The bits in this mask + are defined in the drivers/scsi/aic7xxx/aic7xxx.h - search for the + variable ahc_debug in that file to find them. + +config AIC7XXX_REG_PRETTY_PRINT + bool "Decode registers during diagnostics" + depends on SCSI_AIC7XXX + default y + help + Compile in register value tables for the output of expanded register + contents in diagnostics. This make it much easier to understand debug + output without having to refer to a data book and/or the aic7xxx.reg + file. diff --git a/drivers/scsi/aic7xxx/Makefile b/drivers/scsi/aic7xxx/Makefile new file mode 100644 index 000000000..e0188ecd8 --- /dev/null +++ b/drivers/scsi/aic7xxx/Makefile @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: GPL-2.0 +# +# Makefile for the Linux aic7xxx SCSI driver. +# +# $Id: //depot/linux-aic79xx-2.5.0/drivers/scsi/aic7xxx/Makefile#8 $ +# + +# Let kbuild descend into aicasm when cleaning +subdir- += aicasm + +obj-$(CONFIG_SCSI_AIC7XXX) += aic7xxx.o +obj-$(CONFIG_SCSI_AIC79XX) += aic79xx.o + +# Core Fast -> U160 files +aic7xxx-y += aic7xxx_core.o \ + aic7xxx_93cx6.o +aic7xxx-$(CONFIG_EISA) += aic7770.o +aic7xxx-$(CONFIG_PCI) += aic7xxx_pci.o +aic7xxx-$(CONFIG_AIC7XXX_REG_PRETTY_PRINT) += aic7xxx_reg_print.o + +# Platform Specific Fast -> U160 Files +aic7xxx-y += aic7xxx_osm.o \ + aic7xxx_proc.o +aic7xxx-$(CONFIG_EISA) += aic7770_osm.o +aic7xxx-$(CONFIG_PCI) += aic7xxx_osm_pci.o + +# Core U320 files +aic79xx-y += aic79xx_core.o \ + aic79xx_pci.o +aic79xx-$(CONFIG_AIC79XX_REG_PRETTY_PRINT) += aic79xx_reg_print.o + +# Platform Specific U320 Files +aic79xx-y += aic79xx_osm.o \ + aic79xx_proc.o \ + aic79xx_osm_pci.o + +ifdef WARNINGS_BECOME_ERRORS +ccflags-y += -Werror +endif + +# Files generated that shall be removed upon make clean +clean-files := aic7xxx_seq.h aic7xxx_reg.h aic7xxx_reg_print.c +clean-files += aic79xx_seq.h aic79xx_reg.h aic79xx_reg_print.c + +# Dependencies for generated files need to be listed explicitly + +$(addprefix $(obj)/,$(aic7xxx-y)): $(obj)/aic7xxx_seq.h $(obj)/aic7xxx_reg.h +$(addprefix $(obj)/,$(aic79xx-y)): $(obj)/aic79xx_seq.h $(obj)/aic79xx_reg.h + +aic7xxx-gen-$(CONFIG_AIC7XXX_BUILD_FIRMWARE) := $(obj)/aic7xxx_reg.h +aic7xxx-gen-$(CONFIG_AIC7XXX_REG_PRETTY_PRINT) += $(obj)/aic7xxx_reg_print.c + +aicasm-7xxx-opts-$(CONFIG_AIC7XXX_REG_PRETTY_PRINT) := \ + -p $(obj)/aic7xxx_reg_print.c -i aic7xxx_osm.h + +ifeq ($(CONFIG_AIC7XXX_BUILD_FIRMWARE),y) +$(obj)/aic7xxx_seq.h: $(src)/aic7xxx.seq $(src)/aic7xxx.reg $(obj)/aicasm/aicasm + $(obj)/aicasm/aicasm -I$(srctree)/$(src) -r $(obj)/aic7xxx_reg.h \ + $(aicasm-7xxx-opts-y) -o $(obj)/aic7xxx_seq.h \ + $(srctree)/$(src)/aic7xxx.seq + +$(aic7xxx-gen-y): $(objtree)/$(obj)/aic7xxx_seq.h + @true +else +$(obj)/aic7xxx_reg_print.c: $(src)/aic7xxx_reg_print.c_shipped +endif + +aic79xx-gen-$(CONFIG_AIC79XX_BUILD_FIRMWARE) := $(obj)/aic79xx_reg.h +aic79xx-gen-$(CONFIG_AIC79XX_REG_PRETTY_PRINT) += $(obj)/aic79xx_reg_print.c + +aicasm-79xx-opts-$(CONFIG_AIC79XX_REG_PRETTY_PRINT) := \ + -p $(obj)/aic79xx_reg_print.c -i aic79xx_osm.h + +ifeq ($(CONFIG_AIC79XX_BUILD_FIRMWARE),y) +$(obj)/aic79xx_seq.h: $(src)/aic79xx.seq $(src)/aic79xx.reg $(obj)/aicasm/aicasm + $(obj)/aicasm/aicasm -I$(srctree)/$(src) -r $(obj)/aic79xx_reg.h \ + $(aicasm-79xx-opts-y) -o $(obj)/aic79xx_seq.h \ + $(srctree)/$(src)/aic79xx.seq + +$(aic79xx-gen-y): $(objtree)/$(obj)/aic79xx_seq.h + @true +else +$(obj)/aic79xx_reg_print.c: $(src)/aic79xx_reg_print.c_shipped +endif + +$(obj)/aicasm/aicasm: $(srctree)/$(src)/aicasm/*.[chyl] + $(MAKE) -C $(srctree)/$(src)/aicasm OUTDIR=$(shell pwd)/$(obj)/aicasm/ diff --git a/drivers/scsi/aic7xxx/aic7770.c b/drivers/scsi/aic7xxx/aic7770.c new file mode 100644 index 000000000..176704b24 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7770.c @@ -0,0 +1,385 @@ +/* + * Product specific probe and attach routines for: + * 27/284X and aic7770 motherboard SCSI controllers + * + * Copyright (c) 1994-1998, 2000, 2001 Justin T. Gibbs. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aic7770.c#32 $ + * + * $FreeBSD$ + */ + +#include "aic7xxx_osm.h" +#include "aic7xxx_inline.h" +#include "aic7xxx_93cx6.h" + +#define ID_AIC7770 0x04907770 +#define ID_AHA_274x 0x04907771 +#define ID_AHA_284xB 0x04907756 /* BIOS enabled */ +#define ID_AHA_284x 0x04907757 /* BIOS disabled*/ +#define ID_OLV_274x 0x04907782 /* Olivetti OEM */ +#define ID_OLV_274xD 0x04907783 /* Olivetti OEM (Differential) */ + +static int aic7770_chip_init(struct ahc_softc *ahc); +static int aha2840_load_seeprom(struct ahc_softc *ahc); +static ahc_device_setup_t ahc_aic7770_VL_setup; +static ahc_device_setup_t ahc_aic7770_EISA_setup; +static ahc_device_setup_t ahc_aic7770_setup; + +struct aic7770_identity aic7770_ident_table[] = +{ + { + ID_AHA_274x, + 0xFFFFFFFF, + "Adaptec 274X SCSI adapter", + ahc_aic7770_EISA_setup + }, + { + ID_AHA_284xB, + 0xFFFFFFFE, + "Adaptec 284X SCSI adapter", + ahc_aic7770_VL_setup + }, + { + ID_AHA_284x, + 0xFFFFFFFE, + "Adaptec 284X SCSI adapter (BIOS Disabled)", + ahc_aic7770_VL_setup + }, + { + ID_OLV_274x, + 0xFFFFFFFF, + "Adaptec (Olivetti OEM) 274X SCSI adapter", + ahc_aic7770_EISA_setup + }, + { + ID_OLV_274xD, + 0xFFFFFFFF, + "Adaptec (Olivetti OEM) 274X Differential SCSI adapter", + ahc_aic7770_EISA_setup + }, + /* Generic chip probes for devices we don't know 'exactly' */ + { + ID_AIC7770, + 0xFFFFFFFF, + "Adaptec aic7770 SCSI adapter", + ahc_aic7770_EISA_setup + } +}; +const int ahc_num_aic7770_devs = ARRAY_SIZE(aic7770_ident_table); + +struct aic7770_identity * +aic7770_find_device(uint32_t id) +{ + struct aic7770_identity *entry; + int i; + + for (i = 0; i < ahc_num_aic7770_devs; i++) { + entry = &aic7770_ident_table[i]; + if (entry->full_id == (id & entry->id_mask)) + return (entry); + } + return (NULL); +} + +int +aic7770_config(struct ahc_softc *ahc, struct aic7770_identity *entry, u_int io) +{ + int error; + int have_seeprom; + u_int hostconf; + u_int irq; + u_int intdef; + + error = entry->setup(ahc); + have_seeprom = 0; + if (error != 0) + return (error); + + error = aic7770_map_registers(ahc, io); + if (error != 0) + return (error); + + /* + * Before we continue probing the card, ensure that + * its interrupts are *disabled*. We don't want + * a misstep to hang the machine in an interrupt + * storm. + */ + ahc_intr_enable(ahc, FALSE); + + ahc->description = entry->name; + error = ahc_softc_init(ahc); + if (error != 0) + return (error); + + ahc->bus_chip_init = aic7770_chip_init; + + error = ahc_reset(ahc, /*reinit*/FALSE); + if (error != 0) + return (error); + + /* Make sure we have a valid interrupt vector */ + intdef = ahc_inb(ahc, INTDEF); + irq = intdef & VECTOR; + switch (irq) { + case 9: + case 10: + case 11: + case 12: + case 14: + case 15: + break; + default: + printk("aic7770_config: invalid irq setting %d\n", intdef); + return (ENXIO); + } + + if ((intdef & EDGE_TRIG) != 0) + ahc->flags |= AHC_EDGE_INTERRUPT; + + switch (ahc->chip & (AHC_EISA|AHC_VL)) { + case AHC_EISA: + { + u_int biosctrl; + u_int scsiconf; + u_int scsiconf1; + + biosctrl = ahc_inb(ahc, HA_274_BIOSCTRL); + scsiconf = ahc_inb(ahc, SCSICONF); + scsiconf1 = ahc_inb(ahc, SCSICONF + 1); + + /* Get the primary channel information */ + if ((biosctrl & CHANNEL_B_PRIMARY) != 0) + ahc->flags |= 1; + + if ((biosctrl & BIOSMODE) == BIOSDISABLED) { + ahc->flags |= AHC_USEDEFAULTS; + } else { + if ((ahc->features & AHC_WIDE) != 0) { + ahc->our_id = scsiconf1 & HWSCSIID; + if (scsiconf & TERM_ENB) + ahc->flags |= AHC_TERM_ENB_A; + } else { + ahc->our_id = scsiconf & HSCSIID; + ahc->our_id_b = scsiconf1 & HSCSIID; + if (scsiconf & TERM_ENB) + ahc->flags |= AHC_TERM_ENB_A; + if (scsiconf1 & TERM_ENB) + ahc->flags |= AHC_TERM_ENB_B; + } + } + if ((ahc_inb(ahc, HA_274_BIOSGLOBAL) & HA_274_EXTENDED_TRANS)) + ahc->flags |= AHC_EXTENDED_TRANS_A|AHC_EXTENDED_TRANS_B; + break; + } + case AHC_VL: + { + have_seeprom = aha2840_load_seeprom(ahc); + break; + } + default: + break; + } + if (have_seeprom == 0) { + kfree(ahc->seep_config); + ahc->seep_config = NULL; + } + + /* + * Ensure autoflush is enabled + */ + ahc_outb(ahc, SBLKCTL, ahc_inb(ahc, SBLKCTL) & ~AUTOFLUSHDIS); + + /* Setup the FIFO threshold and the bus off time */ + hostconf = ahc_inb(ahc, HOSTCONF); + ahc_outb(ahc, BUSSPD, hostconf & DFTHRSH); + ahc_outb(ahc, BUSTIME, (hostconf << 2) & BOFF); + + ahc->bus_softc.aic7770_softc.busspd = hostconf & DFTHRSH; + ahc->bus_softc.aic7770_softc.bustime = (hostconf << 2) & BOFF; + + /* + * Generic aic7xxx initialization. + */ + error = ahc_init(ahc); + if (error != 0) + return (error); + + error = aic7770_map_int(ahc, irq); + if (error != 0) + return (error); + + ahc->init_level++; + + /* + * Enable the board's BUS drivers + */ + ahc_outb(ahc, BCTL, ENABLE); + return (0); +} + +static int +aic7770_chip_init(struct ahc_softc *ahc) +{ + ahc_outb(ahc, BUSSPD, ahc->bus_softc.aic7770_softc.busspd); + ahc_outb(ahc, BUSTIME, ahc->bus_softc.aic7770_softc.bustime); + ahc_outb(ahc, SBLKCTL, ahc_inb(ahc, SBLKCTL) & ~AUTOFLUSHDIS); + ahc_outb(ahc, BCTL, ENABLE); + return (ahc_chip_init(ahc)); +} + +/* + * Read the 284x SEEPROM. + */ +static int +aha2840_load_seeprom(struct ahc_softc *ahc) +{ + struct seeprom_descriptor sd; + struct seeprom_config *sc; + int have_seeprom; + uint8_t scsi_conf; + + sd.sd_ahc = ahc; + sd.sd_control_offset = SEECTL_2840; + sd.sd_status_offset = STATUS_2840; + sd.sd_dataout_offset = STATUS_2840; + sd.sd_chip = C46; + sd.sd_MS = 0; + sd.sd_RDY = EEPROM_TF; + sd.sd_CS = CS_2840; + sd.sd_CK = CK_2840; + sd.sd_DO = DO_2840; + sd.sd_DI = DI_2840; + sc = ahc->seep_config; + + if (bootverbose) + printk("%s: Reading SEEPROM...", ahc_name(ahc)); + have_seeprom = ahc_read_seeprom(&sd, (uint16_t *)sc, + /*start_addr*/0, sizeof(*sc)/2); + + if (have_seeprom) { + + if (ahc_verify_cksum(sc) == 0) { + if(bootverbose) + printk ("checksum error\n"); + have_seeprom = 0; + } else if (bootverbose) { + printk("done.\n"); + } + } + + if (!have_seeprom) { + if (bootverbose) + printk("%s: No SEEPROM available\n", ahc_name(ahc)); + ahc->flags |= AHC_USEDEFAULTS; + } else { + /* + * Put the data we've collected down into SRAM + * where ahc_init will find it. + */ + int i; + int max_targ; + uint16_t discenable; + + max_targ = (ahc->features & AHC_WIDE) != 0 ? 16 : 8; + discenable = 0; + for (i = 0; i < max_targ; i++){ + uint8_t target_settings; + + target_settings = (sc->device_flags[i] & CFXFER) << 4; + if (sc->device_flags[i] & CFSYNCH) + target_settings |= SOFS; + if (sc->device_flags[i] & CFWIDEB) + target_settings |= WIDEXFER; + if (sc->device_flags[i] & CFDISC) + discenable |= (0x01 << i); + ahc_outb(ahc, TARG_SCSIRATE + i, target_settings); + } + ahc_outb(ahc, DISC_DSB, ~(discenable & 0xff)); + ahc_outb(ahc, DISC_DSB + 1, ~((discenable >> 8) & 0xff)); + + ahc->our_id = sc->brtime_id & CFSCSIID; + + scsi_conf = (ahc->our_id & 0x7); + if (sc->adapter_control & CFSPARITY) + scsi_conf |= ENSPCHK; + if (sc->adapter_control & CFRESETB) + scsi_conf |= RESET_SCSI; + + if (sc->bios_control & CF284XEXTEND) + ahc->flags |= AHC_EXTENDED_TRANS_A; + /* Set SCSICONF info */ + ahc_outb(ahc, SCSICONF, scsi_conf); + + if (sc->adapter_control & CF284XSTERM) + ahc->flags |= AHC_TERM_ENB_A; + } + return (have_seeprom); +} + +static int +ahc_aic7770_VL_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7770_setup(ahc); + ahc->chip |= AHC_VL; + return (error); +} + +static int +ahc_aic7770_EISA_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7770_setup(ahc); + ahc->chip |= AHC_EISA; + return (error); +} + +static int +ahc_aic7770_setup(struct ahc_softc *ahc) +{ + ahc->channel = 'A'; + ahc->channel_b = 'B'; + ahc->chip = AHC_AIC7770; + ahc->features = AHC_AIC7770_FE; + ahc->bugs |= AHC_TMODE_WIDEODD_BUG; + ahc->flags |= AHC_PAGESCBS; + ahc->instruction_ram_size = 448; + return (0); +} diff --git a/drivers/scsi/aic7xxx/aic7770_osm.c b/drivers/scsi/aic7xxx/aic7770_osm.c new file mode 100644 index 000000000..bdd177e3d --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7770_osm.c @@ -0,0 +1,156 @@ +/* + * Linux driver attachment glue for aic7770 based controllers. + * + * Copyright (c) 2000-2003 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic7770_osm.c#14 $ + */ + +#include "aic7xxx_osm.h" + +#include <linux/device.h> +#include <linux/eisa.h> + +int +aic7770_map_registers(struct ahc_softc *ahc, u_int port) +{ + /* + * Lock out other contenders for our i/o space. + */ + if (!request_region(port, AHC_EISA_IOSIZE, "aic7xxx")) + return (ENOMEM); + ahc->tag = BUS_SPACE_PIO; + ahc->bsh.ioport = port; + return (0); +} + +int +aic7770_map_int(struct ahc_softc *ahc, u_int irq) +{ + int error; + int shared; + + shared = 0; + if ((ahc->flags & AHC_EDGE_INTERRUPT) == 0) + shared = IRQF_SHARED; + + error = request_irq(irq, ahc_linux_isr, shared, "aic7xxx", ahc); + if (error == 0) + ahc->platform_data->irq = irq; + + return (-error); +} + +static int +aic7770_probe(struct device *dev) +{ + struct eisa_device *edev = to_eisa_device(dev); + u_int eisaBase = edev->base_addr+AHC_EISA_SLOT_OFFSET; + struct ahc_softc *ahc; + char buf[80]; + char *name; + int error; + + sprintf(buf, "ahc_eisa:%d", eisaBase >> 12); + name = kstrdup(buf, GFP_ATOMIC); + if (name == NULL) + return (ENOMEM); + ahc = ahc_alloc(&aic7xxx_driver_template, name); + if (ahc == NULL) + return (ENOMEM); + ahc->dev = dev; + error = aic7770_config(ahc, aic7770_ident_table + edev->id.driver_data, + eisaBase); + if (error != 0) { + ahc->bsh.ioport = 0; + ahc_free(ahc); + return (error); + } + + dev_set_drvdata(dev, ahc); + + error = ahc_linux_register_host(ahc, &aic7xxx_driver_template); + return (error); +} + +static int +aic7770_remove(struct device *dev) +{ + struct ahc_softc *ahc = dev_get_drvdata(dev); + u_long s; + + if (ahc->platform_data && ahc->platform_data->host) + scsi_remove_host(ahc->platform_data->host); + + ahc_lock(ahc, &s); + ahc_intr_enable(ahc, FALSE); + ahc_unlock(ahc, &s); + + ahc_free(ahc); + return 0; +} + +static struct eisa_device_id aic7770_ids[] = { + { "ADP7771", 0 }, /* AHA 274x */ + { "ADP7756", 1 }, /* AHA 284x BIOS enabled */ + { "ADP7757", 2 }, /* AHA 284x BIOS disabled */ + { "ADP7782", 3 }, /* AHA 274x Olivetti OEM */ + { "ADP7783", 4 }, /* AHA 274x Olivetti OEM (Differential) */ + { "ADP7770", 5 }, /* AIC7770 generic */ + { "" } +}; +MODULE_DEVICE_TABLE(eisa, aic7770_ids); + +static struct eisa_driver aic7770_driver = { + .id_table = aic7770_ids, + .driver = { + .name = "aic7xxx", + .probe = aic7770_probe, + .remove = aic7770_remove, + } +}; + +int +ahc_linux_eisa_init(void) +{ + return eisa_driver_register(&aic7770_driver); +} + +void +ahc_linux_eisa_exit(void) +{ + eisa_driver_unregister(&aic7770_driver); +} diff --git a/drivers/scsi/aic7xxx/aic79xx.h b/drivers/scsi/aic7xxx/aic79xx.h new file mode 100644 index 000000000..9a5155516 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx.h @@ -0,0 +1,1469 @@ +/* + * Core definitions and data structures shareable across OS platforms. + * + * Copyright (c) 1994-2002 Justin T. Gibbs. + * Copyright (c) 2000-2002 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aic79xx.h#109 $ + * + * $FreeBSD$ + */ + +#ifndef _AIC79XX_H_ +#define _AIC79XX_H_ + +/* Register Definitions */ +#include "aic79xx_reg.h" + +/************************* Forward Declarations *******************************/ +struct ahd_platform_data; +struct scb_platform_data; + +/****************************** Useful Macros *********************************/ +#ifndef TRUE +#define TRUE 1 +#endif +#ifndef FALSE +#define FALSE 0 +#endif + +#define ALL_CHANNELS '\0' +#define ALL_TARGETS_MASK 0xFFFF +#define INITIATOR_WILDCARD (~0) +#define SCB_LIST_NULL 0xFF00 +#define SCB_LIST_NULL_LE (ahd_htole16(SCB_LIST_NULL)) +#define QOUTFIFO_ENTRY_VALID 0x80 +#define SCBID_IS_NULL(scbid) (((scbid) & 0xFF00 ) == SCB_LIST_NULL) + +#define SCSIID_TARGET(ahd, scsiid) \ + (((scsiid) & TID) >> TID_SHIFT) +#define SCSIID_OUR_ID(scsiid) \ + ((scsiid) & OID) +#define SCSIID_CHANNEL(ahd, scsiid) ('A') +#define SCB_IS_SCSIBUS_B(ahd, scb) (0) +#define SCB_GET_OUR_ID(scb) \ + SCSIID_OUR_ID((scb)->hscb->scsiid) +#define SCB_GET_TARGET(ahd, scb) \ + SCSIID_TARGET((ahd), (scb)->hscb->scsiid) +#define SCB_GET_CHANNEL(ahd, scb) \ + SCSIID_CHANNEL(ahd, (scb)->hscb->scsiid) +#define SCB_GET_LUN(scb) \ + ((scb)->hscb->lun) +#define SCB_GET_TARGET_OFFSET(ahd, scb) \ + SCB_GET_TARGET(ahd, scb) +#define SCB_GET_TARGET_MASK(ahd, scb) \ + (0x01 << (SCB_GET_TARGET_OFFSET(ahd, scb))) +#ifdef AHD_DEBUG +#define SCB_IS_SILENT(scb) \ + ((ahd_debug & AHD_SHOW_MASKED_ERRORS) == 0 \ + && (((scb)->flags & SCB_SILENT) != 0)) +#else +#define SCB_IS_SILENT(scb) \ + (((scb)->flags & SCB_SILENT) != 0) +#endif +/* + * TCLs have the following format: TTTTLLLLLLLL + */ +#define TCL_TARGET_OFFSET(tcl) \ + ((((tcl) >> 4) & TID) >> 4) +#define TCL_LUN(tcl) \ + (tcl & (AHD_NUM_LUNS - 1)) +#define BUILD_TCL(scsiid, lun) \ + ((lun) | (((scsiid) & TID) << 4)) +#define BUILD_TCL_RAW(target, channel, lun) \ + ((lun) | ((target) << 8)) + +#define SCB_GET_TAG(scb) \ + ahd_le16toh(scb->hscb->tag) + +#ifndef AHD_TARGET_MODE +#undef AHD_TMODE_ENABLE +#define AHD_TMODE_ENABLE 0 +#endif + +#define AHD_BUILD_COL_IDX(target, lun) \ + ((((u8)lun) << 4) | target) + +#define AHD_GET_SCB_COL_IDX(ahd, scb) \ + ((SCB_GET_LUN(scb) << 4) | SCB_GET_TARGET(ahd, scb)) + +#define AHD_SET_SCB_COL_IDX(scb, col_idx) \ +do { \ + (scb)->hscb->scsiid = ((col_idx) << TID_SHIFT) & TID; \ + (scb)->hscb->lun = ((col_idx) >> 4) & (AHD_NUM_LUNS_NONPKT-1); \ +} while (0) + +#define AHD_COPY_SCB_COL_IDX(dst, src) \ +do { \ + dst->hscb->scsiid = src->hscb->scsiid; \ + dst->hscb->lun = src->hscb->lun; \ +} while (0) + +#define AHD_NEVER_COL_IDX 0xFFFF + +/**************************** Driver Constants ********************************/ +/* + * The maximum number of supported targets. + */ +#define AHD_NUM_TARGETS 16 + +/* + * The maximum number of supported luns. + * The identify message only supports 64 luns in non-packetized transfers. + * You can have 2^64 luns when information unit transfers are enabled, + * but until we see a need to support that many, we support 256. + */ +#define AHD_NUM_LUNS_NONPKT 64 +#define AHD_NUM_LUNS 256 + +/* + * The maximum transfer per S/G segment. + */ +#define AHD_MAXTRANSFER_SIZE 0x00ffffff /* limited by 24bit counter */ + +/* + * The maximum amount of SCB storage in hardware on a controller. + * This value represents an upper bound. Due to software design, + * we may not be able to use this number. + */ +#define AHD_SCB_MAX 512 + +/* + * The maximum number of concurrent transactions supported per driver instance. + * Sequencer Control Blocks (SCBs) store per-transaction information. + */ +#define AHD_MAX_QUEUE AHD_SCB_MAX + +/* + * Define the size of our QIN and QOUT FIFOs. They must be a power of 2 + * in size and accommodate as many transactions as can be queued concurrently. + */ +#define AHD_QIN_SIZE AHD_MAX_QUEUE +#define AHD_QOUT_SIZE AHD_MAX_QUEUE + +#define AHD_QIN_WRAP(x) ((x) & (AHD_QIN_SIZE-1)) +/* + * The maximum amount of SCB storage we allocate in host memory. + */ +#define AHD_SCB_MAX_ALLOC AHD_MAX_QUEUE + +/* + * Ring Buffer of incoming target commands. + * We allocate 256 to simplify the logic in the sequencer + * by using the natural wrap point of an 8bit counter. + */ +#define AHD_TMODE_CMDS 256 + +/* Reset line assertion time in us */ +#define AHD_BUSRESET_DELAY 25 + +/******************* Chip Characteristics/Operating Settings *****************/ +/* + * Chip Type + * The chip order is from least sophisticated to most sophisticated. + */ +typedef enum { + AHD_NONE = 0x0000, + AHD_CHIPID_MASK = 0x00FF, + AHD_AIC7901 = 0x0001, + AHD_AIC7902 = 0x0002, + AHD_AIC7901A = 0x0003, + AHD_PCI = 0x0100, /* Bus type PCI */ + AHD_PCIX = 0x0200, /* Bus type PCIX */ + AHD_BUS_MASK = 0x0F00 +} ahd_chip; + +/* + * Features available in each chip type. + */ +typedef enum { + AHD_FENONE = 0x00000, + AHD_WIDE = 0x00001,/* Wide Channel */ + AHD_AIC79XXB_SLOWCRC = 0x00002,/* SLOWCRC bit should be set */ + AHD_MULTI_FUNC = 0x00100,/* Multi-Function/Channel Device */ + AHD_TARGETMODE = 0x01000,/* Has tested target mode support */ + AHD_MULTIROLE = 0x02000,/* Space for two roles at a time */ + AHD_RTI = 0x04000,/* Retained Training Support */ + AHD_NEW_IOCELL_OPTS = 0x08000,/* More Signal knobs in the IOCELL */ + AHD_NEW_DFCNTRL_OPTS = 0x10000,/* SCSIENWRDIS bit */ + AHD_FAST_CDB_DELIVERY = 0x20000,/* CDB acks released to Output Sync */ + AHD_REMOVABLE = 0x00000,/* Hot-Swap supported - None so far*/ + AHD_AIC7901_FE = AHD_FENONE, + AHD_AIC7901A_FE = AHD_FENONE, + AHD_AIC7902_FE = AHD_MULTI_FUNC +} ahd_feature; + +/* + * Bugs in the silicon that we work around in software. + */ +typedef enum { + AHD_BUGNONE = 0x0000, + /* + * Rev A hardware fails to update LAST/CURR/NEXTSCB + * correctly in certain packetized selection cases. + */ + AHD_SENT_SCB_UPDATE_BUG = 0x0001, + /* The wrong SCB is accessed to check the abort pending bit. */ + AHD_ABORT_LQI_BUG = 0x0002, + /* Packetized bitbucket crosses packet boundaries. */ + AHD_PKT_BITBUCKET_BUG = 0x0004, + /* The selection timer runs twice as long as its setting. */ + AHD_LONG_SETIMO_BUG = 0x0008, + /* The Non-LQ CRC error status is delayed until phase change. */ + AHD_NLQICRC_DELAYED_BUG = 0x0010, + /* The chip must be reset for all outgoing bus resets. */ + AHD_SCSIRST_BUG = 0x0020, + /* Some PCIX fields must be saved and restored across chip reset. */ + AHD_PCIX_CHIPRST_BUG = 0x0040, + /* MMAPIO is not functional in PCI-X mode. */ + AHD_PCIX_MMAPIO_BUG = 0x0080, + /* Reads to SCBRAM fail to reset the discard timer. */ + AHD_PCIX_SCBRAM_RD_BUG = 0x0100, + /* Bug workarounds that can be disabled on non-PCIX busses. */ + AHD_PCIX_BUG_MASK = AHD_PCIX_CHIPRST_BUG + | AHD_PCIX_MMAPIO_BUG + | AHD_PCIX_SCBRAM_RD_BUG, + /* + * LQOSTOP0 status set even for forced selections with ATN + * to perform non-packetized message delivery. + */ + AHD_LQO_ATNO_BUG = 0x0200, + /* FIFO auto-flush does not always trigger. */ + AHD_AUTOFLUSH_BUG = 0x0400, + /* The CLRLQO registers are not self-clearing. */ + AHD_CLRLQO_AUTOCLR_BUG = 0x0800, + /* The PACKETIZED status bit refers to the previous connection. */ + AHD_PKTIZED_STATUS_BUG = 0x1000, + /* "Short Luns" are not placed into outgoing LQ packets correctly. */ + AHD_PKT_LUN_BUG = 0x2000, + /* + * Only the FIFO allocated to the non-packetized connection may + * be in use during a non-packetzied connection. + */ + AHD_NONPACKFIFO_BUG = 0x4000, + /* + * Writing to a DFF SCBPTR register may fail if concurent with + * a hardware write to the other DFF SCBPTR register. This is + * not currently a concern in our sequencer since all chips with + * this bug have the AHD_NONPACKFIFO_BUG and all writes of concern + * occur in non-packetized connections. + */ + AHD_MDFF_WSCBPTR_BUG = 0x8000, + /* SGHADDR updates are slow. */ + AHD_REG_SLOW_SETTLE_BUG = 0x10000, + /* + * Changing the MODE_PTR coincident with an interrupt that + * switches to a different mode will cause the interrupt to + * be in the mode written outside of interrupt context. + */ + AHD_SET_MODE_BUG = 0x20000, + /* Non-packetized busfree revision does not work. */ + AHD_BUSFREEREV_BUG = 0x40000, + /* + * Paced transfers are indicated with a non-standard PPR + * option bit in the neg table, 160MHz is indicated by + * sync factor 0x7, and the offset if off by a factor of 2. + */ + AHD_PACED_NEGTABLE_BUG = 0x80000, + /* LQOOVERRUN false positives. */ + AHD_LQOOVERRUN_BUG = 0x100000, + /* + * Controller write to INTSTAT will lose to a host + * write to CLRINT. + */ + AHD_INTCOLLISION_BUG = 0x200000, + /* + * The GEM318 violates the SCSI spec by not waiting + * the mandated bus settle delay between phase changes + * in some situations. Some aic79xx chip revs. are more + * strict in this regard and will treat REQ assertions + * that fall within the bus settle delay window as + * glitches. This flag tells the firmware to tolerate + * early REQ assertions. + */ + AHD_EARLY_REQ_BUG = 0x400000, + /* + * The LED does not stay on long enough in packetized modes. + */ + AHD_FAINT_LED_BUG = 0x800000 +} ahd_bug; + +/* + * Configuration specific settings. + * The driver determines these settings by probing the + * chip/controller's configuration. + */ +typedef enum { + AHD_FNONE = 0x00000, + AHD_BOOT_CHANNEL = 0x00001,/* We were set as the boot channel. */ + AHD_USEDEFAULTS = 0x00004,/* + * For cards without an seeprom + * or a BIOS to initialize the chip's + * SRAM, we use the default target + * settings. + */ + AHD_SEQUENCER_DEBUG = 0x00008, + AHD_RESET_BUS_A = 0x00010, + AHD_EXTENDED_TRANS_A = 0x00020, + AHD_TERM_ENB_A = 0x00040, + AHD_SPCHK_ENB_A = 0x00080, + AHD_STPWLEVEL_A = 0x00100, + AHD_INITIATORROLE = 0x00200,/* + * Allow initiator operations on + * this controller. + */ + AHD_TARGETROLE = 0x00400,/* + * Allow target operations on this + * controller. + */ + AHD_RESOURCE_SHORTAGE = 0x00800, + AHD_TQINFIFO_BLOCKED = 0x01000,/* Blocked waiting for ATIOs */ + AHD_INT50_SPEEDFLEX = 0x02000,/* + * Internal 50pin connector + * sits behind an aic3860 + */ + AHD_BIOS_ENABLED = 0x04000, + AHD_ALL_INTERRUPTS = 0x08000, + AHD_39BIT_ADDRESSING = 0x10000,/* Use 39 bit addressing scheme. */ + AHD_64BIT_ADDRESSING = 0x20000,/* Use 64 bit addressing scheme. */ + AHD_CURRENT_SENSING = 0x40000, + AHD_SCB_CONFIG_USED = 0x80000,/* No SEEPROM but SCB had info. */ + AHD_HP_BOARD = 0x100000, + AHD_BUS_RESET_ACTIVE = 0x200000, + AHD_UPDATE_PEND_CMDS = 0x400000, + AHD_RUNNING_QOUTFIFO = 0x800000, + AHD_HAD_FIRST_SEL = 0x1000000 +} ahd_flag; + +/************************* Hardware SCB Definition ***************************/ + +/* + * The driver keeps up to MAX_SCB scb structures per card in memory. The SCB + * consists of a "hardware SCB" mirroring the fields available on the card + * and additional information the kernel stores for each transaction. + * + * To minimize space utilization, a portion of the hardware scb stores + * different data during different portions of a SCSI transaction. + * As initialized by the host driver for the initiator role, this area + * contains the SCSI cdb (or a pointer to the cdb) to be executed. After + * the cdb has been presented to the target, this area serves to store + * residual transfer information and the SCSI status byte. + * For the target role, the contents of this area do not change, but + * still serve a different purpose than for the initiator role. See + * struct target_data for details. + */ + +/* + * Status information embedded in the shared poriton of + * an SCB after passing the cdb to the target. The kernel + * driver will only read this data for transactions that + * complete abnormally. + */ +struct initiator_status { + uint32_t residual_datacnt; /* Residual in the current S/G seg */ + uint32_t residual_sgptr; /* The next S/G for this transfer */ + uint8_t scsi_status; /* Standard SCSI status byte */ +}; + +struct target_status { + uint32_t residual_datacnt; /* Residual in the current S/G seg */ + uint32_t residual_sgptr; /* The next S/G for this transfer */ + uint8_t scsi_status; /* SCSI status to give to initiator */ + uint8_t target_phases; /* Bitmap of phases to execute */ + uint8_t data_phase; /* Data-In or Data-Out */ + uint8_t initiator_tag; /* Initiator's transaction tag */ +}; + +/* + * Initiator mode SCB shared data area. + * If the embedded CDB is 12 bytes or less, we embed + * the sense buffer address in the SCB. This allows + * us to retrieve sense information without interrupting + * the host in packetized mode. + */ +typedef uint32_t sense_addr_t; +#define MAX_CDB_LEN 16 +#define MAX_CDB_LEN_WITH_SENSE_ADDR (MAX_CDB_LEN - sizeof(sense_addr_t)) +union initiator_data { + struct { + uint64_t cdbptr; + uint8_t cdblen; + } cdb_from_host; + uint8_t cdb[MAX_CDB_LEN]; + struct { + uint8_t cdb[MAX_CDB_LEN_WITH_SENSE_ADDR]; + sense_addr_t sense_addr; + } cdb_plus_saddr; +}; + +/* + * Target mode version of the shared data SCB segment. + */ +struct target_data { + uint32_t spare[2]; + uint8_t scsi_status; /* SCSI status to give to initiator */ + uint8_t target_phases; /* Bitmap of phases to execute */ + uint8_t data_phase; /* Data-In or Data-Out */ + uint8_t initiator_tag; /* Initiator's transaction tag */ +}; + +struct hardware_scb { +/*0*/ union { + union initiator_data idata; + struct target_data tdata; + struct initiator_status istatus; + struct target_status tstatus; + } shared_data; +/* + * A word about residuals. + * The scb is presented to the sequencer with the dataptr and datacnt + * fields initialized to the contents of the first S/G element to + * transfer. The sgptr field is initialized to the bus address for + * the S/G element that follows the first in the in core S/G array + * or'ed with the SG_FULL_RESID flag. Sgptr may point to an invalid + * S/G entry for this transfer (single S/G element transfer with the + * first elements address and length preloaded in the dataptr/datacnt + * fields). If no transfer is to occur, sgptr is set to SG_LIST_NULL. + * The SG_FULL_RESID flag ensures that the residual will be correctly + * noted even if no data transfers occur. Once the data phase is entered, + * the residual sgptr and datacnt are loaded from the sgptr and the + * datacnt fields. After each S/G element's dataptr and length are + * loaded into the hardware, the residual sgptr is advanced. After + * each S/G element is expired, its datacnt field is checked to see + * if the LAST_SEG flag is set. If so, SG_LIST_NULL is set in the + * residual sg ptr and the transfer is considered complete. If the + * sequencer determines that there is a residual in the tranfer, or + * there is non-zero status, it will set the SG_STATUS_VALID flag in + * sgptr and dma the scb back into host memory. To sumarize: + * + * Sequencer: + * o A residual has occurred if SG_FULL_RESID is set in sgptr, + * or residual_sgptr does not have SG_LIST_NULL set. + * + * o We are transferring the last segment if residual_datacnt has + * the SG_LAST_SEG flag set. + * + * Host: + * o A residual can only have occurred if a completed scb has the + * SG_STATUS_VALID flag set. Inspection of the SCSI status field, + * the residual_datacnt, and the residual_sgptr field will tell + * for sure. + * + * o residual_sgptr and sgptr refer to the "next" sg entry + * and so may point beyond the last valid sg entry for the + * transfer. + */ +#define SG_PTR_MASK 0xFFFFFFF8 +/*16*/ uint16_t tag; /* Reused by Sequencer. */ +/*18*/ uint8_t control; /* See SCB_CONTROL in aic79xx.reg for details */ +/*19*/ uint8_t scsiid; /* + * Selection out Id + * Our Id (bits 0-3) Their ID (bits 4-7) + */ +/*20*/ uint8_t lun; +/*21*/ uint8_t task_attribute; +/*22*/ uint8_t cdb_len; +/*23*/ uint8_t task_management; +/*24*/ uint64_t dataptr; +/*32*/ uint32_t datacnt; /* Byte 3 is spare. */ +/*36*/ uint32_t sgptr; +/*40*/ uint32_t hscb_busaddr; +/*44*/ uint32_t next_hscb_busaddr; +/********** Long lun field only downloaded for full 8 byte lun support ********/ +/*48*/ uint8_t pkt_long_lun[8]; +/******* Fields below are not Downloaded (Sequencer may use for scratch) ******/ +/*56*/ uint8_t spare[8]; +}; + +/************************ Kernel SCB Definitions ******************************/ +/* + * Some fields of the SCB are OS dependent. Here we collect the + * definitions for elements that all OS platforms need to include + * in there SCB definition. + */ + +/* + * Definition of a scatter/gather element as transferred to the controller. + * The aic7xxx chips only support a 24bit length. We use the top byte of + * the length to store additional address bits and a flag to indicate + * that a given segment terminates the transfer. This gives us an + * addressable range of 512GB on machines with 64bit PCI or with chips + * that can support dual address cycles on 32bit PCI busses. + */ +struct ahd_dma_seg { + uint32_t addr; + uint32_t len; +#define AHD_DMA_LAST_SEG 0x80000000 +#define AHD_SG_HIGH_ADDR_MASK 0x7F000000 +#define AHD_SG_LEN_MASK 0x00FFFFFF +}; + +struct ahd_dma64_seg { + uint64_t addr; + uint32_t len; + uint32_t pad; +}; + +struct map_node { + bus_dmamap_t dmamap; + dma_addr_t physaddr; + uint8_t *vaddr; + SLIST_ENTRY(map_node) links; +}; + +/* + * The current state of this SCB. + */ +typedef enum { + SCB_FLAG_NONE = 0x00000, + SCB_TRANSMISSION_ERROR = 0x00001,/* + * We detected a parity or CRC + * error that has effected the + * payload of the command. This + * flag is checked when normal + * status is returned to catch + * the case of a target not + * responding to our attempt + * to report the error. + */ + SCB_OTHERTCL_TIMEOUT = 0x00002,/* + * Another device was active + * during the first timeout for + * this SCB so we gave ourselves + * an additional timeout period + * in case it was hogging the + * bus. + */ + SCB_DEVICE_RESET = 0x00004, + SCB_SENSE = 0x00008, + SCB_CDB32_PTR = 0x00010, + SCB_RECOVERY_SCB = 0x00020, + SCB_AUTO_NEGOTIATE = 0x00040,/* Negotiate to achieve goal. */ + SCB_NEGOTIATE = 0x00080,/* Negotiation forced for command. */ + SCB_ABORT = 0x00100, + SCB_ACTIVE = 0x00200, + SCB_TARGET_IMMEDIATE = 0x00400, + SCB_PACKETIZED = 0x00800, + SCB_EXPECT_PPR_BUSFREE = 0x01000, + SCB_PKT_SENSE = 0x02000, + SCB_EXTERNAL_RESET = 0x04000,/* Device was reset externally */ + SCB_ON_COL_LIST = 0x08000, + SCB_SILENT = 0x10000 /* + * Be quiet about transmission type + * errors. They are expected and we + * don't want to upset the user. This + * flag is typically used during DV. + */ +} scb_flag; + +struct scb { + struct hardware_scb *hscb; + union { + SLIST_ENTRY(scb) sle; + LIST_ENTRY(scb) le; + TAILQ_ENTRY(scb) tqe; + } links; + union { + SLIST_ENTRY(scb) sle; + LIST_ENTRY(scb) le; + TAILQ_ENTRY(scb) tqe; + } links2; +#define pending_links links2.le +#define collision_links links2.le + struct scb *col_scb; + ahd_io_ctx_t io_ctx; + struct ahd_softc *ahd_softc; + scb_flag flags; + struct scb_platform_data *platform_data; + struct map_node *hscb_map; + struct map_node *sg_map; + struct map_node *sense_map; + void *sg_list; + uint8_t *sense_data; + dma_addr_t sg_list_busaddr; + dma_addr_t sense_busaddr; + u_int sg_count;/* How full ahd_dma_seg is */ +#define AHD_MAX_LQ_CRC_ERRORS 5 + u_int crc_retry_count; +}; + +TAILQ_HEAD(scb_tailq, scb); +BSD_LIST_HEAD(scb_list, scb); + +struct scb_data { + /* + * TAILQ of lists of free SCBs grouped by device + * collision domains. + */ + struct scb_tailq free_scbs; + + /* + * Per-device lists of SCBs whose tag ID would collide + * with an already active tag on the device. + */ + struct scb_list free_scb_lists[AHD_NUM_TARGETS * AHD_NUM_LUNS_NONPKT]; + + /* + * SCBs that will not collide with any active device. + */ + struct scb_list any_dev_free_scb_list; + + /* + * Mapping from tag to SCB. + */ + struct scb *scbindex[AHD_SCB_MAX]; + + /* + * "Bus" addresses of our data structures. + */ + bus_dma_tag_t hscb_dmat; /* dmat for our hardware SCB array */ + bus_dma_tag_t sg_dmat; /* dmat for our sg segments */ + bus_dma_tag_t sense_dmat; /* dmat for our sense buffers */ + SLIST_HEAD(, map_node) hscb_maps; + SLIST_HEAD(, map_node) sg_maps; + SLIST_HEAD(, map_node) sense_maps; + int scbs_left; /* unallocated scbs in head map_node */ + int sgs_left; /* unallocated sgs in head map_node */ + int sense_left; /* unallocated sense in head map_node */ + uint16_t numscbs; + uint16_t maxhscbs; /* Number of SCBs on the card */ + uint8_t init_level; /* + * How far we've initialized + * this structure. + */ +}; + +/************************ Target Mode Definitions *****************************/ + +/* + * Connection descriptor for select-in requests in target mode. + */ +struct target_cmd { + uint8_t scsiid; /* Our ID and the initiator's ID */ + uint8_t identify; /* Identify message */ + uint8_t bytes[22]; /* + * Bytes contains any additional message + * bytes terminated by 0xFF. The remainder + * is the cdb to execute. + */ + uint8_t cmd_valid; /* + * When a command is complete, the firmware + * will set cmd_valid to all bits set. + * After the host has seen the command, + * the bits are cleared. This allows us + * to just peek at host memory to determine + * if more work is complete. cmd_valid is on + * an 8 byte boundary to simplify setting + * it on aic7880 hardware which only has + * limited direct access to the DMA FIFO. + */ + uint8_t pad[7]; +}; + +/* + * Number of events we can buffer up if we run out + * of immediate notify ccbs. + */ +#define AHD_TMODE_EVENT_BUFFER_SIZE 8 +struct ahd_tmode_event { + uint8_t initiator_id; + uint8_t event_type; /* MSG type or EVENT_TYPE_BUS_RESET */ +#define EVENT_TYPE_BUS_RESET 0xFF + uint8_t event_arg; +}; + +/* + * Per enabled lun target mode state. + * As this state is directly influenced by the host OS'es target mode + * environment, we let the OS module define it. Forward declare the + * structure here so we can store arrays of them, etc. in OS neutral + * data structures. + */ +#ifdef AHD_TARGET_MODE +struct ahd_tmode_lstate { + struct cam_path *path; + struct ccb_hdr_slist accept_tios; + struct ccb_hdr_slist immed_notifies; + struct ahd_tmode_event event_buffer[AHD_TMODE_EVENT_BUFFER_SIZE]; + uint8_t event_r_idx; + uint8_t event_w_idx; +}; +#else +struct ahd_tmode_lstate; +#endif + +/******************** Transfer Negotiation Datastructures *********************/ +#define AHD_TRANS_CUR 0x01 /* Modify current neogtiation status */ +#define AHD_TRANS_ACTIVE 0x03 /* Assume this target is on the bus */ +#define AHD_TRANS_GOAL 0x04 /* Modify negotiation goal */ +#define AHD_TRANS_USER 0x08 /* Modify user negotiation settings */ +#define AHD_PERIOD_10MHz 0x19 + +#define AHD_WIDTH_UNKNOWN 0xFF +#define AHD_PERIOD_UNKNOWN 0xFF +#define AHD_OFFSET_UNKNOWN 0xFF +#define AHD_PPR_OPTS_UNKNOWN 0xFF + +/* + * Transfer Negotiation Information. + */ +struct ahd_transinfo { + uint8_t protocol_version; /* SCSI Revision level */ + uint8_t transport_version; /* SPI Revision level */ + uint8_t width; /* Bus width */ + uint8_t period; /* Sync rate factor */ + uint8_t offset; /* Sync offset */ + uint8_t ppr_options; /* Parallel Protocol Request options */ +}; + +/* + * Per-initiator current, goal and user transfer negotiation information. */ +struct ahd_initiator_tinfo { + struct ahd_transinfo curr; + struct ahd_transinfo goal; + struct ahd_transinfo user; +}; + +/* + * Per enabled target ID state. + * Pointers to lun target state as well as sync/wide negotiation information + * for each initiator<->target mapping. For the initiator role we pretend + * that we are the target and the targets are the initiators since the + * negotiation is the same regardless of role. + */ +struct ahd_tmode_tstate { + struct ahd_tmode_lstate* enabled_luns[AHD_NUM_LUNS]; + struct ahd_initiator_tinfo transinfo[AHD_NUM_TARGETS]; + + /* + * Per initiator state bitmasks. + */ + uint16_t auto_negotiate;/* Auto Negotiation Required */ + uint16_t discenable; /* Disconnection allowed */ + uint16_t tagenable; /* Tagged Queuing allowed */ +}; + +/* + * Points of interest along the negotiated transfer scale. + */ +#define AHD_SYNCRATE_160 0x8 +#define AHD_SYNCRATE_PACED 0x8 +#define AHD_SYNCRATE_DT 0x9 +#define AHD_SYNCRATE_ULTRA2 0xa +#define AHD_SYNCRATE_ULTRA 0xc +#define AHD_SYNCRATE_FAST 0x19 +#define AHD_SYNCRATE_MIN_DT AHD_SYNCRATE_FAST +#define AHD_SYNCRATE_SYNC 0x32 +#define AHD_SYNCRATE_MIN 0x60 +#define AHD_SYNCRATE_ASYNC 0xFF +#define AHD_SYNCRATE_MAX AHD_SYNCRATE_160 + +/* Safe and valid period for async negotiations. */ +#define AHD_ASYNC_XFER_PERIOD 0x44 + +/* + * In RevA, the synctable uses a 120MHz rate for the period + * factor 8 and 160MHz for the period factor 7. The 120MHz + * rate never made it into the official SCSI spec, so we must + * compensate when setting the negotiation table for Rev A + * parts. + */ +#define AHD_SYNCRATE_REVA_120 0x8 +#define AHD_SYNCRATE_REVA_160 0x7 + +/***************************** Lookup Tables **********************************/ +/* + * Phase -> name and message out response + * to parity errors in each phase table. + */ +struct ahd_phase_table_entry { + uint8_t phase; + uint8_t mesg_out; /* Message response to parity errors */ + const char *phasemsg; +}; + +/************************** Serial EEPROM Format ******************************/ + +struct seeprom_config { +/* + * Per SCSI ID Configuration Flags + */ + uint16_t device_flags[16]; /* words 0-15 */ +#define CFXFER 0x003F /* synchronous transfer rate */ +#define CFXFER_ASYNC 0x3F +#define CFQAS 0x0040 /* Negotiate QAS */ +#define CFPACKETIZED 0x0080 /* Negotiate Packetized Transfers */ +#define CFSTART 0x0100 /* send start unit SCSI command */ +#define CFINCBIOS 0x0200 /* include in BIOS scan */ +#define CFDISC 0x0400 /* enable disconnection */ +#define CFMULTILUNDEV 0x0800 /* Probe multiple luns in BIOS scan */ +#define CFWIDEB 0x1000 /* wide bus device */ +#define CFHOSTMANAGED 0x8000 /* Managed by a RAID controller */ + +/* + * BIOS Control Bits + */ + uint16_t bios_control; /* word 16 */ +#define CFSUPREM 0x0001 /* support all removeable drives */ +#define CFSUPREMB 0x0002 /* support removeable boot drives */ +#define CFBIOSSTATE 0x000C /* BIOS Action State */ +#define CFBS_DISABLED 0x00 +#define CFBS_ENABLED 0x04 +#define CFBS_DISABLED_SCAN 0x08 +#define CFENABLEDV 0x0010 /* Perform Domain Validation */ +#define CFCTRL_A 0x0020 /* BIOS displays Ctrl-A message */ +#define CFSPARITY 0x0040 /* SCSI parity */ +#define CFEXTEND 0x0080 /* extended translation enabled */ +#define CFBOOTCD 0x0100 /* Support Bootable CD-ROM */ +#define CFMSG_LEVEL 0x0600 /* BIOS Message Level */ +#define CFMSG_VERBOSE 0x0000 +#define CFMSG_SILENT 0x0200 +#define CFMSG_DIAG 0x0400 +#define CFRESETB 0x0800 /* reset SCSI bus at boot */ +/* UNUSED 0xf000 */ + +/* + * Host Adapter Control Bits + */ + uint16_t adapter_control; /* word 17 */ +#define CFAUTOTERM 0x0001 /* Perform Auto termination */ +#define CFSTERM 0x0002 /* SCSI low byte termination */ +#define CFWSTERM 0x0004 /* SCSI high byte termination */ +#define CFSEAUTOTERM 0x0008 /* Ultra2 Perform secondary Auto Term*/ +#define CFSELOWTERM 0x0010 /* Ultra2 secondary low term */ +#define CFSEHIGHTERM 0x0020 /* Ultra2 secondary high term */ +#define CFSTPWLEVEL 0x0040 /* Termination level control */ +#define CFBIOSAUTOTERM 0x0080 /* Perform Auto termination */ +#define CFTERM_MENU 0x0100 /* BIOS displays termination menu */ +#define CFCLUSTERENB 0x8000 /* Cluster Enable */ + +/* + * Bus Release Time, Host Adapter ID + */ + uint16_t brtime_id; /* word 18 */ +#define CFSCSIID 0x000f /* host adapter SCSI ID */ +/* UNUSED 0x00f0 */ +#define CFBRTIME 0xff00 /* bus release time/PCI Latency Time */ + +/* + * Maximum targets + */ + uint16_t max_targets; /* word 19 */ +#define CFMAXTARG 0x00ff /* maximum targets */ +#define CFBOOTLUN 0x0f00 /* Lun to boot from */ +#define CFBOOTID 0xf000 /* Target to boot from */ + uint16_t res_1[10]; /* words 20-29 */ + uint16_t signature; /* BIOS Signature */ +#define CFSIGNATURE 0x400 + uint16_t checksum; /* word 31 */ +}; + +/* + * Vital Product Data used during POST and by the BIOS. + */ +struct vpd_config { + uint8_t bios_flags; +#define VPDMASTERBIOS 0x0001 +#define VPDBOOTHOST 0x0002 + uint8_t reserved_1[21]; + uint8_t resource_type; + uint8_t resource_len[2]; + uint8_t resource_data[8]; + uint8_t vpd_tag; + uint16_t vpd_len; + uint8_t vpd_keyword[2]; + uint8_t length; + uint8_t revision; + uint8_t device_flags; + uint8_t termination_menus[2]; + uint8_t fifo_threshold; + uint8_t end_tag; + uint8_t vpd_checksum; + uint16_t default_target_flags; + uint16_t default_bios_flags; + uint16_t default_ctrl_flags; + uint8_t default_irq; + uint8_t pci_lattime; + uint8_t max_target; + uint8_t boot_lun; + uint16_t signature; + uint8_t reserved_2; + uint8_t checksum; + uint8_t reserved_3[4]; +}; + +/****************************** Flexport Logic ********************************/ +#define FLXADDR_TERMCTL 0x0 +#define FLX_TERMCTL_ENSECHIGH 0x8 +#define FLX_TERMCTL_ENSECLOW 0x4 +#define FLX_TERMCTL_ENPRIHIGH 0x2 +#define FLX_TERMCTL_ENPRILOW 0x1 +#define FLXADDR_ROMSTAT_CURSENSECTL 0x1 +#define FLX_ROMSTAT_SEECFG 0xF0 +#define FLX_ROMSTAT_EECFG 0x0F +#define FLX_ROMSTAT_SEE_93C66 0x00 +#define FLX_ROMSTAT_SEE_NONE 0xF0 +#define FLX_ROMSTAT_EE_512x8 0x0 +#define FLX_ROMSTAT_EE_1MBx8 0x1 +#define FLX_ROMSTAT_EE_2MBx8 0x2 +#define FLX_ROMSTAT_EE_4MBx8 0x3 +#define FLX_ROMSTAT_EE_16MBx8 0x4 +#define CURSENSE_ENB 0x1 +#define FLXADDR_FLEXSTAT 0x2 +#define FLX_FSTAT_BUSY 0x1 +#define FLXADDR_CURRENT_STAT 0x4 +#define FLX_CSTAT_SEC_HIGH 0xC0 +#define FLX_CSTAT_SEC_LOW 0x30 +#define FLX_CSTAT_PRI_HIGH 0x0C +#define FLX_CSTAT_PRI_LOW 0x03 +#define FLX_CSTAT_MASK 0x03 +#define FLX_CSTAT_SHIFT 2 +#define FLX_CSTAT_OKAY 0x0 +#define FLX_CSTAT_OVER 0x1 +#define FLX_CSTAT_UNDER 0x2 +#define FLX_CSTAT_INVALID 0x3 + +int ahd_read_seeprom(struct ahd_softc *ahd, uint16_t *buf, + u_int start_addr, u_int count, int bstream); + +int ahd_write_seeprom(struct ahd_softc *ahd, uint16_t *buf, + u_int start_addr, u_int count); +int ahd_verify_cksum(struct seeprom_config *sc); +int ahd_acquire_seeprom(struct ahd_softc *ahd); +void ahd_release_seeprom(struct ahd_softc *ahd); + +/**************************** Message Buffer *********************************/ +typedef enum { + MSG_FLAG_NONE = 0x00, + MSG_FLAG_EXPECT_PPR_BUSFREE = 0x01, + MSG_FLAG_IU_REQ_CHANGED = 0x02, + MSG_FLAG_EXPECT_IDE_BUSFREE = 0x04, + MSG_FLAG_EXPECT_QASREJ_BUSFREE = 0x08, + MSG_FLAG_PACKETIZED = 0x10 +} ahd_msg_flags; + +typedef enum { + MSG_TYPE_NONE = 0x00, + MSG_TYPE_INITIATOR_MSGOUT = 0x01, + MSG_TYPE_INITIATOR_MSGIN = 0x02, + MSG_TYPE_TARGET_MSGOUT = 0x03, + MSG_TYPE_TARGET_MSGIN = 0x04 +} ahd_msg_type; + +typedef enum { + MSGLOOP_IN_PROG, + MSGLOOP_MSGCOMPLETE, + MSGLOOP_TERMINATED +} msg_loop_stat; + +/*********************** Software Configuration Structure *********************/ +struct ahd_suspend_channel_state { + uint8_t scsiseq; + uint8_t sxfrctl0; + uint8_t sxfrctl1; + uint8_t simode0; + uint8_t simode1; + uint8_t seltimer; + uint8_t seqctl; +}; + +struct ahd_suspend_pci_state { + uint32_t devconfig; + uint8_t command; + uint8_t csize_lattime; +}; + +struct ahd_suspend_state { + struct ahd_suspend_channel_state channel[2]; + struct ahd_suspend_pci_state pci_state; + uint8_t optionmode; + uint8_t dscommand0; + uint8_t dspcistatus; + /* hsmailbox */ + uint8_t crccontrol1; + uint8_t scbbaddr; + /* Host and sequencer SCB counts */ + uint8_t dff_thrsh; + uint8_t *scratch_ram; + uint8_t *btt; +}; + +typedef void (*ahd_bus_intr_t)(struct ahd_softc *); + +typedef enum { + AHD_MODE_DFF0, + AHD_MODE_DFF1, + AHD_MODE_CCHAN, + AHD_MODE_SCSI, + AHD_MODE_CFG, + AHD_MODE_UNKNOWN +} ahd_mode; + +#define AHD_MK_MSK(x) (0x01 << (x)) +#define AHD_MODE_DFF0_MSK AHD_MK_MSK(AHD_MODE_DFF0) +#define AHD_MODE_DFF1_MSK AHD_MK_MSK(AHD_MODE_DFF1) +#define AHD_MODE_CCHAN_MSK AHD_MK_MSK(AHD_MODE_CCHAN) +#define AHD_MODE_SCSI_MSK AHD_MK_MSK(AHD_MODE_SCSI) +#define AHD_MODE_CFG_MSK AHD_MK_MSK(AHD_MODE_CFG) +#define AHD_MODE_UNKNOWN_MSK AHD_MK_MSK(AHD_MODE_UNKNOWN) +#define AHD_MODE_ANY_MSK (~0) + +typedef uint8_t ahd_mode_state; + +struct ahd_completion +{ + uint16_t tag; + uint8_t sg_status; + uint8_t valid_tag; +}; + +struct ahd_softc { + bus_space_tag_t tags[2]; + bus_space_handle_t bshs[2]; + struct scb_data scb_data; + + struct hardware_scb *next_queued_hscb; + struct map_node *next_queued_hscb_map; + + /* + * SCBs that have been sent to the controller + */ + BSD_LIST_HEAD(, scb) pending_scbs; + + /* + * Current register window mode information. + */ + ahd_mode dst_mode; + ahd_mode src_mode; + + /* + * Saved register window mode information + * used for restore on next unpause. + */ + ahd_mode saved_dst_mode; + ahd_mode saved_src_mode; + + /* + * Platform specific data. + */ + struct ahd_platform_data *platform_data; + + /* + * Platform specific device information. + */ + ahd_dev_softc_t dev_softc; + + /* + * Bus specific device information. + */ + ahd_bus_intr_t bus_intr; + + /* + * Target mode related state kept on a per enabled lun basis. + * Targets that are not enabled will have null entries. + * As an initiator, we keep one target entry for our initiator + * ID to store our sync/wide transfer settings. + */ + struct ahd_tmode_tstate *enabled_targets[AHD_NUM_TARGETS]; + + /* + * The black hole device responsible for handling requests for + * disabled luns on enabled targets. + */ + struct ahd_tmode_lstate *black_hole; + + /* + * Device instance currently on the bus awaiting a continue TIO + * for a command that was not given the disconnect priveledge. + */ + struct ahd_tmode_lstate *pending_device; + + /* + * Timer handles for timer driven callbacks. + */ + struct timer_list stat_timer; + + /* + * Statistics. + */ +#define AHD_STAT_UPDATE_US 250000 /* 250ms */ +#define AHD_STAT_BUCKETS 4 + u_int cmdcmplt_bucket; + uint32_t cmdcmplt_counts[AHD_STAT_BUCKETS]; + uint32_t cmdcmplt_total; + + /* + * Card characteristics + */ + ahd_chip chip; + ahd_feature features; + ahd_bug bugs; + ahd_flag flags; + struct seeprom_config *seep_config; + + /* Command Queues */ + struct ahd_completion *qoutfifo; + uint16_t qoutfifonext; + uint16_t qoutfifonext_valid_tag; + uint16_t qinfifonext; + uint16_t qinfifo[AHD_SCB_MAX]; + + /* + * Our qfreeze count. The sequencer compares + * this value with its own counter to determine + * whether to allow selections to occur. + */ + uint16_t qfreeze_cnt; + + /* Values to store in the SEQCTL register for pause and unpause */ + uint8_t unpause; + uint8_t pause; + + /* Critical Section Data */ + struct cs *critical_sections; + u_int num_critical_sections; + + /* Buffer for handling packetized bitbucket. */ + uint8_t *overrun_buf; + + /* Links for chaining softcs */ + TAILQ_ENTRY(ahd_softc) links; + + /* Channel Names ('A', 'B', etc.) */ + char channel; + + /* Initiator Bus ID */ + uint8_t our_id; + + /* + * Target incoming command FIFO. + */ + struct target_cmd *targetcmds; + uint8_t tqinfifonext; + + /* + * Cached verson of the hs_mailbox so we can avoid + * pausing the sequencer during mailbox updates. + */ + uint8_t hs_mailbox; + + /* + * Incoming and outgoing message handling. + */ + uint8_t send_msg_perror; + ahd_msg_flags msg_flags; + ahd_msg_type msg_type; + uint8_t msgout_buf[12];/* Message we are sending */ + uint8_t msgin_buf[12];/* Message we are receiving */ + u_int msgout_len; /* Length of message to send */ + u_int msgout_index; /* Current index in msgout */ + u_int msgin_index; /* Current index in msgin */ + + /* + * Mapping information for data structures shared + * between the sequencer and kernel. + */ + bus_dma_tag_t parent_dmat; + bus_dma_tag_t shared_data_dmat; + struct map_node shared_data_map; + + /* Information saved through suspend/resume cycles */ + struct ahd_suspend_state suspend_state; + + /* Number of enabled target mode device on this card */ + u_int enabled_luns; + + /* Initialization level of this data structure */ + u_int init_level; + + /* PCI cacheline size. */ + u_int pci_cachesize; + + /* IO Cell Parameters */ + uint8_t iocell_opts[AHD_NUM_PER_DEV_ANNEXCOLS]; + + u_int stack_size; + uint16_t *saved_stack; + + /* Per-Unit descriptive information */ + const char *description; + const char *bus_description; + char *name; + int unit; + + /* Selection Timer settings */ + int seltime; + + /* + * Interrupt coalescing settings. + */ +#define AHD_INT_COALESCING_TIMER_DEFAULT 250 /*us*/ +#define AHD_INT_COALESCING_MAXCMDS_DEFAULT 10 +#define AHD_INT_COALESCING_MAXCMDS_MAX 127 +#define AHD_INT_COALESCING_MINCMDS_DEFAULT 5 +#define AHD_INT_COALESCING_MINCMDS_MAX 127 +#define AHD_INT_COALESCING_THRESHOLD_DEFAULT 2000 +#define AHD_INT_COALESCING_STOP_THRESHOLD_DEFAULT 1000 + u_int int_coalescing_timer; + u_int int_coalescing_maxcmds; + u_int int_coalescing_mincmds; + u_int int_coalescing_threshold; + u_int int_coalescing_stop_threshold; + + uint16_t user_discenable;/* Disconnection allowed */ + uint16_t user_tagenable;/* Tagged Queuing allowed */ +}; + +/*************************** IO Cell Configuration ****************************/ +#define AHD_PRECOMP_SLEW_INDEX \ + (AHD_ANNEXCOL_PRECOMP_SLEW - AHD_ANNEXCOL_PER_DEV0) + +#define AHD_AMPLITUDE_INDEX \ + (AHD_ANNEXCOL_AMPLITUDE - AHD_ANNEXCOL_PER_DEV0) + +#define AHD_SET_SLEWRATE(ahd, new_slew) \ +do { \ + (ahd)->iocell_opts[AHD_PRECOMP_SLEW_INDEX] &= ~AHD_SLEWRATE_MASK; \ + (ahd)->iocell_opts[AHD_PRECOMP_SLEW_INDEX] |= \ + (((new_slew) << AHD_SLEWRATE_SHIFT) & AHD_SLEWRATE_MASK); \ +} while (0) + +#define AHD_SET_PRECOMP(ahd, new_pcomp) \ +do { \ + (ahd)->iocell_opts[AHD_PRECOMP_SLEW_INDEX] &= ~AHD_PRECOMP_MASK; \ + (ahd)->iocell_opts[AHD_PRECOMP_SLEW_INDEX] |= \ + (((new_pcomp) << AHD_PRECOMP_SHIFT) & AHD_PRECOMP_MASK); \ +} while (0) + +#define AHD_SET_AMPLITUDE(ahd, new_amp) \ +do { \ + (ahd)->iocell_opts[AHD_AMPLITUDE_INDEX] &= ~AHD_AMPLITUDE_MASK; \ + (ahd)->iocell_opts[AHD_AMPLITUDE_INDEX] |= \ + (((new_amp) << AHD_AMPLITUDE_SHIFT) & AHD_AMPLITUDE_MASK); \ +} while (0) + +/************************ Active Device Information ***************************/ +typedef enum { + ROLE_UNKNOWN, + ROLE_INITIATOR, + ROLE_TARGET +} role_t; + +struct ahd_devinfo { + int our_scsiid; + int target_offset; + uint16_t target_mask; + u_int target; + u_int lun; + char channel; + role_t role; /* + * Only guaranteed to be correct if not + * in the busfree state. + */ +}; + +/****************************** PCI Structures ********************************/ +#define AHD_PCI_IOADDR0 PCIR_BAR(0) /* I/O BAR*/ +#define AHD_PCI_MEMADDR PCIR_BAR(1) /* Memory BAR */ +#define AHD_PCI_IOADDR1 PCIR_BAR(3) /* Second I/O BAR */ + +typedef int (ahd_device_setup_t)(struct ahd_softc *); + +struct ahd_pci_identity { + uint64_t full_id; + uint64_t id_mask; + const char *name; + ahd_device_setup_t *setup; +}; + +/***************************** VL/EISA Declarations ***************************/ +struct aic7770_identity { + uint32_t full_id; + uint32_t id_mask; + const char *name; + ahd_device_setup_t *setup; +}; +extern struct aic7770_identity aic7770_ident_table []; +extern const int ahd_num_aic7770_devs; + +#define AHD_EISA_SLOT_OFFSET 0xc00 +#define AHD_EISA_IOSIZE 0x100 + +/*************************** Function Declarations ****************************/ +/******************************************************************************/ + +/***************************** PCI Front End *********************************/ +const struct ahd_pci_identity *ahd_find_pci_device(ahd_dev_softc_t); +int ahd_pci_config(struct ahd_softc *, + const struct ahd_pci_identity *); +int ahd_pci_test_register_access(struct ahd_softc *); +#ifdef CONFIG_PM +void ahd_pci_suspend(struct ahd_softc *); +void ahd_pci_resume(struct ahd_softc *); +#endif + +/************************** SCB and SCB queue management **********************/ +void ahd_qinfifo_requeue_tail(struct ahd_softc *ahd, + struct scb *scb); + +/****************************** Initialization ********************************/ +struct ahd_softc *ahd_alloc(void *platform_arg, char *name); +int ahd_softc_init(struct ahd_softc *); +void ahd_controller_info(struct ahd_softc *ahd, char *buf); +int ahd_init(struct ahd_softc *ahd); +#ifdef CONFIG_PM +int ahd_suspend(struct ahd_softc *ahd); +void ahd_resume(struct ahd_softc *ahd); +#endif +int ahd_default_config(struct ahd_softc *ahd); +int ahd_parse_vpddata(struct ahd_softc *ahd, + struct vpd_config *vpd); +int ahd_parse_cfgdata(struct ahd_softc *ahd, + struct seeprom_config *sc); +void ahd_intr_enable(struct ahd_softc *ahd, int enable); +void ahd_pause_and_flushwork(struct ahd_softc *ahd); +void ahd_set_unit(struct ahd_softc *, int); +void ahd_set_name(struct ahd_softc *, char *); +struct scb *ahd_get_scb(struct ahd_softc *ahd, u_int col_idx); +void ahd_free_scb(struct ahd_softc *ahd, struct scb *scb); +void ahd_free(struct ahd_softc *ahd); +int ahd_reset(struct ahd_softc *ahd, int reinit); +int ahd_write_flexport(struct ahd_softc *ahd, + u_int addr, u_int value); +int ahd_read_flexport(struct ahd_softc *ahd, u_int addr, + uint8_t *value); + +/***************************** Error Recovery *********************************/ +typedef enum { + SEARCH_COMPLETE, + SEARCH_COUNT, + SEARCH_REMOVE, + SEARCH_PRINT +} ahd_search_action; +int ahd_search_qinfifo(struct ahd_softc *ahd, int target, + char channel, int lun, u_int tag, + role_t role, uint32_t status, + ahd_search_action action); +int ahd_search_disc_list(struct ahd_softc *ahd, int target, + char channel, int lun, u_int tag, + int stop_on_first, int remove, + int save_state); +int ahd_reset_channel(struct ahd_softc *ahd, char channel, + int initiate_reset); +/*************************** Utility Functions ********************************/ +void ahd_compile_devinfo(struct ahd_devinfo *devinfo, + u_int our_id, u_int target, + u_int lun, char channel, + role_t role); +/************************** Transfer Negotiation ******************************/ +void ahd_find_syncrate(struct ahd_softc *ahd, u_int *period, + u_int *ppr_options, u_int maxsync); +/* + * Negotiation types. These are used to qualify if we should renegotiate + * even if our goal and current transport parameters are identical. + */ +typedef enum { + AHD_NEG_TO_GOAL, /* Renegotiate only if goal and curr differ. */ + AHD_NEG_IF_NON_ASYNC, /* Renegotiate so long as goal is non-async. */ + AHD_NEG_ALWAYS /* Renegotiat even if goal is async. */ +} ahd_neg_type; +int ahd_update_neg_request(struct ahd_softc*, + struct ahd_devinfo*, + struct ahd_tmode_tstate*, + struct ahd_initiator_tinfo*, + ahd_neg_type); +void ahd_set_width(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo, + u_int width, u_int type, int paused); +void ahd_set_syncrate(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo, + u_int period, u_int offset, + u_int ppr_options, + u_int type, int paused); +typedef enum { + AHD_QUEUE_NONE, + AHD_QUEUE_BASIC, + AHD_QUEUE_TAGGED +} ahd_queue_alg; + +/**************************** Target Mode *************************************/ +#ifdef AHD_TARGET_MODE +void ahd_send_lstate_events(struct ahd_softc *, + struct ahd_tmode_lstate *); +void ahd_handle_en_lun(struct ahd_softc *ahd, + struct cam_sim *sim, union ccb *ccb); +cam_status ahd_find_tmode_devs(struct ahd_softc *ahd, + struct cam_sim *sim, union ccb *ccb, + struct ahd_tmode_tstate **tstate, + struct ahd_tmode_lstate **lstate, + int notfound_failure); +#ifndef AHD_TMODE_ENABLE +#define AHD_TMODE_ENABLE 0 +#endif +#endif +/******************************* Debug ***************************************/ +#ifdef AHD_DEBUG +extern uint32_t ahd_debug; +#define AHD_SHOW_MISC 0x00001 +#define AHD_SHOW_SENSE 0x00002 +#define AHD_SHOW_RECOVERY 0x00004 +#define AHD_DUMP_SEEPROM 0x00008 +#define AHD_SHOW_TERMCTL 0x00010 +#define AHD_SHOW_MEMORY 0x00020 +#define AHD_SHOW_MESSAGES 0x00040 +#define AHD_SHOW_MODEPTR 0x00080 +#define AHD_SHOW_SELTO 0x00100 +#define AHD_SHOW_FIFOS 0x00200 +#define AHD_SHOW_QFULL 0x00400 +#define AHD_SHOW_DV 0x00800 +#define AHD_SHOW_MASKED_ERRORS 0x01000 +#define AHD_SHOW_QUEUE 0x02000 +#define AHD_SHOW_TQIN 0x04000 +#define AHD_SHOW_SG 0x08000 +#define AHD_SHOW_INT_COALESCING 0x10000 +#define AHD_DEBUG_SEQUENCER 0x20000 +#endif +void ahd_print_devinfo(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo); +void ahd_dump_card_state(struct ahd_softc *ahd); +int ahd_print_register(const ahd_reg_parse_entry_t *table, + u_int num_entries, + const char *name, + u_int address, + u_int value, + u_int *cur_column, + u_int wrap_point); +#endif /* _AIC79XX_H_ */ diff --git a/drivers/scsi/aic7xxx/aic79xx.reg b/drivers/scsi/aic7xxx/aic79xx.reg new file mode 100644 index 000000000..7e12c31cc --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx.reg @@ -0,0 +1,4281 @@ +/* + * Aic79xx register and scratch ram definitions. + * + * Copyright (c) 1994-2001, 2004 Justin T. Gibbs. + * Copyright (c) 2000-2002 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $FreeBSD$ + */ +VERSION = "$Id: //depot/aic7xxx/aic7xxx/aic79xx.reg#77 $" + +/* + * This file is processed by the aic7xxx_asm utility for use in assembling + * firmware for the aic79xx family of SCSI host adapters as well as to generate + * a C header file for use in the kernel portion of the Aic79xx driver. + */ + +/* Register window Modes */ +#define M_DFF0 0 +#define M_DFF1 1 +#define M_CCHAN 2 +#define M_SCSI 3 +#define M_CFG 4 +#define M_DST_SHIFT 4 + +#define MK_MODE(src, dst) ((src) | ((dst) << M_DST_SHIFT)) +#define SET_MODE(src, dst) \ + SET_SRC_MODE src; \ + SET_DST_MODE dst; \ + if ((ahd->bugs & AHD_SET_MODE_BUG) != 0) { \ + mvi MK_MODE(src, dst) call set_mode_work_around; \ + } else { \ + mvi MODE_PTR, MK_MODE(src, dst); \ + } + +#define RESTORE_MODE(mode) \ + if ((ahd->bugs & AHD_SET_MODE_BUG) != 0) { \ + mov mode call set_mode_work_around; \ + } else { \ + mov MODE_PTR, mode; \ + } + +#define SET_SEQINTCODE(code) \ + if ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0) { \ + mvi code call set_seqint_work_around; \ + } else { \ + mvi SEQINTCODE, code; \ + } + +/* + * Registers marked "dont_generate_debug_code" are not (yet) referenced + * from the driver code, and this keyword inhibit generation + * of debug code for them. + * + * REG_PRETTY_PRINT config will complain if dont_generate_debug_code + * is added to the register which is referenced in the driver. + * Unreferenced register with no dont_generate_debug_code will result + * in dead code. No warning is issued. + */ + +/* + * Mode Pointer + * Controls which of the 5, 512byte, address spaces should be used + * as the source and destination of any register accesses in our + * register window. + */ +register MODE_PTR { + address 0x000 + access_mode RW + field DST_MODE 0x70 + field SRC_MODE 0x07 + mode_pointer + dont_generate_debug_code +} + +const SRC_MODE_SHIFT 0 +const DST_MODE_SHIFT 4 + +/* + * Host Interrupt Status + */ +register INTSTAT { + address 0x001 + access_mode RW + field HWERRINT 0x80 + field BRKADRINT 0x40 + field SWTMINT 0x20 + field PCIINT 0x10 + field SCSIINT 0x08 + field SEQINT 0x04 + field CMDCMPLT 0x02 + field SPLTINT 0x01 + mask INT_PEND 0xFF +} + +/* + * Sequencer Interrupt Code + */ +register SEQINTCODE { + address 0x002 + access_mode RW + field { + NO_SEQINT, /* No seqint pending. */ + BAD_PHASE, /* unknown scsi bus phase */ + SEND_REJECT, /* sending a message reject */ + PROTO_VIOLATION, /* Protocol Violation */ + NO_MATCH, /* no cmd match for reconnect */ + IGN_WIDE_RES, /* Complex IGN Wide Res Msg */ + PDATA_REINIT, /* + * Returned to data phase + * that requires data + * transfer pointers to be + * recalculated from the + * transfer residual. + */ + HOST_MSG_LOOP, /* + * The bus is ready for the + * host to perform another + * message transaction. This + * mechanism is used for things + * like sync/wide negotiation + * that require a kernel based + * message state engine. + */ + BAD_STATUS, /* Bad status from target */ + DATA_OVERRUN, /* + * Target attempted to write + * beyond the bounds of its + * command. + */ + MKMSG_FAILED, /* + * Target completed command + * without honoring our ATN + * request to issue a message. + */ + MISSED_BUSFREE, /* + * The sequencer never saw + * the bus go free after + * either a command complete + * or disconnect message. + */ + DUMP_CARD_STATE, + ILLEGAL_PHASE, + INVALID_SEQINT, + CFG4ISTAT_INTR, + STATUS_OVERRUN, + CFG4OVERRUN, + ENTERING_NONPACK, + TASKMGMT_FUNC_COMPLETE, /* + * Task management function + * request completed with + * an expected busfree. + */ + TASKMGMT_CMD_CMPLT_OKAY, /* + * A command with a non-zero + * task management function + * has completed via the normal + * command completion method + * for commands with a zero + * task management function. + * This happens when an attempt + * to abort a command loses + * the race for the command to + * complete normally. + */ + TRACEPOINT0, + TRACEPOINT1, + TRACEPOINT2, + TRACEPOINT3, + SAW_HWERR, + BAD_SCB_STATUS + } + dont_generate_debug_code +} + +/* + * Clear Host Interrupt + */ +register CLRINT { + address 0x003 + access_mode WO + count 19 + field CLRHWERRINT 0x80 /* Rev B or greater */ + field CLRBRKADRINT 0x40 + field CLRSWTMINT 0x20 + field CLRPCIINT 0x10 + field CLRSCSIINT 0x08 + field CLRSEQINT 0x04 + field CLRCMDINT 0x02 + field CLRSPLTINT 0x01 + dont_generate_debug_code +} + +/* + * Error Register + */ +register ERROR { + address 0x004 + access_mode RO + field CIOPARERR 0x80 + field CIOACCESFAIL 0x40 /* Rev B or greater */ + field MPARERR 0x20 + field DPARERR 0x10 + field SQPARERR 0x08 + field ILLOPCODE 0x04 + field DSCTMOUT 0x02 + dont_generate_debug_code +} + +/* + * Clear Error + */ +register CLRERR { + address 0x004 + access_mode WO + field CLRCIOPARERR 0x80 + field CLRCIOACCESFAIL 0x40 /* Rev B or greater */ + field CLRMPARERR 0x20 + field CLRDPARERR 0x10 + field CLRSQPARERR 0x08 + field CLRILLOPCODE 0x04 + field CLRDSCTMOUT 0x02 +} + +/* + * Host Control Register + * Overall host control of the device. + */ +register HCNTRL { + address 0x005 + access_mode RW + count 12 + field SEQ_RESET 0x80 /* Rev B or greater */ + field POWRDN 0x40 + field SWINT 0x10 + field SWTIMER_START_B 0x08 /* Rev B or greater */ + field PAUSE 0x04 + field INTEN 0x02 + field CHIPRST 0x01 + field CHIPRSTACK 0x01 + dont_generate_debug_code +} + +/* + * Host New SCB Queue Offset + */ +register HNSCB_QOFF { + address 0x006 + access_mode RW + size 2 + count 2 + dont_generate_debug_code +} + +/* + * Host Empty SCB Queue Offset + */ +register HESCB_QOFF { + address 0x008 + access_mode RW + count 2 + dont_generate_debug_code +} + +/* + * Host Mailbox + */ +register HS_MAILBOX { + address 0x00B + access_mode RW + mask HOST_TQINPOS 0x80 /* Boundary at either 0 or 128 */ + mask ENINT_COALESCE 0x40 /* Perform interrupt coalescing */ +} + +/* + * Sequencer Interrupt Status + */ +register SEQINTSTAT { + address 0x00C + count 1 + access_mode RO + field SEQ_SWTMRTO 0x10 + field SEQ_SEQINT 0x08 + field SEQ_SCSIINT 0x04 + field SEQ_PCIINT 0x02 + field SEQ_SPLTINT 0x01 +} + +/* + * Clear SEQ Interrupt + */ +register CLRSEQINTSTAT { + address 0x00C + access_mode WO + field CLRSEQ_SWTMRTO 0x10 + field CLRSEQ_SEQINT 0x08 + field CLRSEQ_SCSIINT 0x04 + field CLRSEQ_PCIINT 0x02 + field CLRSEQ_SPLTINT 0x01 + dont_generate_debug_code +} + +/* + * Software Timer + */ +register SWTIMER { + address 0x00E + access_mode RW + size 2 + dont_generate_debug_code +} + +/* + * SEQ New SCB Queue Offset + */ +register SNSCB_QOFF { + address 0x010 + access_mode RW + size 2 + modes M_CCHAN + dont_generate_debug_code +} + +/* + * SEQ Empty SCB Queue Offset + */ +register SESCB_QOFF { + address 0x012 + count 2 + access_mode RW + modes M_CCHAN + dont_generate_debug_code +} + +/* + * SEQ Done SCB Queue Offset + */ +register SDSCB_QOFF { + address 0x014 + access_mode RW + modes M_CCHAN + size 2 + dont_generate_debug_code +} + +/* + * Queue Offset Control & Status + */ +register QOFF_CTLSTA { + address 0x016 + access_mode RW + modes M_CCHAN + field EMPTY_SCB_AVAIL 0x80 + field NEW_SCB_AVAIL 0x40 + field SDSCB_ROLLOVR 0x20 + field HS_MAILBOX_ACT 0x10 + field SCB_QSIZE 0x0F { + SCB_QSIZE_4, + SCB_QSIZE_8, + SCB_QSIZE_16, + SCB_QSIZE_32, + SCB_QSIZE_64, + SCB_QSIZE_128, + SCB_QSIZE_256, + SCB_QSIZE_512, + SCB_QSIZE_1024, + SCB_QSIZE_2048, + SCB_QSIZE_4096, + SCB_QSIZE_8192, + SCB_QSIZE_16384 + } + dont_generate_debug_code +} + +/* + * Interrupt Control + */ +register INTCTL { + address 0x018 + access_mode RW + field SWTMINTMASK 0x80 + field SWTMINTEN 0x40 + field SWTIMER_START 0x20 + field AUTOCLRCMDINT 0x10 + field PCIINTEN 0x08 + field SCSIINTEN 0x04 + field SEQINTEN 0x02 + field SPLTINTEN 0x01 +} + +/* + * Data FIFO Control + */ +register DFCNTRL { + address 0x019 + access_mode RW + modes M_DFF0, M_DFF1 + count 11 + field PRELOADEN 0x80 + field SCSIENWRDIS 0x40 /* Rev B only. */ + field SCSIEN 0x20 + field SCSIENACK 0x20 + field HDMAEN 0x08 + field HDMAENACK 0x08 + field DIRECTION 0x04 + field DIRECTIONACK 0x04 + field FIFOFLUSH 0x02 + field FIFOFLUSHACK 0x02 + field DIRECTIONEN 0x01 +} + +/* + * Device Space Command 0 + */ +register DSCOMMAND0 { + address 0x019 + count 1 + access_mode RW + modes M_CFG + field CACHETHEN 0x80 /* Cache Threshold enable */ + field DPARCKEN 0x40 /* Data Parity Check Enable */ + field MPARCKEN 0x20 /* Memory Parity Check Enable */ + field EXTREQLCK 0x10 /* External Request Lock */ + field DISABLE_TWATE 0x02 /* Rev B or greater */ + field CIOPARCKEN 0x01 /* Internal bus parity error enable */ + dont_generate_debug_code +} + +/* + * Data FIFO Status + */ +register DFSTATUS { + address 0x01A + access_mode RO + modes M_DFF0, M_DFF1 + field PRELOAD_AVAIL 0x80 + field PKT_PRELOAD_AVAIL 0x40 + field MREQPEND 0x10 + field HDONE 0x08 + field DFTHRESH 0x04 + field FIFOFULL 0x02 + field FIFOEMP 0x01 +} + +/* + * S/G Cache Pointer + */ +register SG_CACHE_PRE { + address 0x01B + access_mode WO + modes M_DFF0, M_DFF1 + field SG_ADDR_MASK 0xf8 + field ODD_SEG 0x04 + field LAST_SEG 0x02 + dont_generate_debug_code +} + +register SG_CACHE_SHADOW { + address 0x01B + access_mode RO + modes M_DFF0, M_DFF1 + field SG_ADDR_MASK 0xf8 + field ODD_SEG 0x04 + field LAST_SEG 0x02 + field LAST_SEG_DONE 0x01 +} + +/* + * Arbiter Control + */ +register ARBCTL { + address 0x01B + access_mode RW + modes M_CFG + field RESET_HARB 0x80 + field RETRY_SWEN 0x08 + field USE_TIME 0x07 +} + +/* + * Data Channel Host Address + */ +register HADDR { + address 0x070 + access_mode RW + size 8 + modes M_DFF0, M_DFF1 + dont_generate_debug_code +} + +/* + * Host Overlay DMA Address + */ +register HODMAADR { + address 0x070 + access_mode RW + size 8 + modes M_SCSI +} + +/* + * PCI PLL Delay. + */ +register PLLDELAY { + address 0x070 + access_mode RW + size 1 + modes M_CFG + field SPLIT_DROP_REQ 0x80 +} + +/* + * Data Channel Host Count + */ +register HCNT { + address 0x078 + access_mode RW + size 3 + modes M_DFF0, M_DFF1 + dont_generate_debug_code +} + +/* + * Host Overlay DMA Count + */ +register HODMACNT { + address 0x078 + access_mode RW + size 2 + modes M_SCSI +} + +/* + * Host Overlay DMA Enable + */ +register HODMAEN { + address 0x07A + access_mode RW + modes M_SCSI +} + +/* + * Scatter/Gather Host Address + */ +register SGHADDR { + address 0x07C + access_mode RW + size 8 + modes M_DFF0, M_DFF1 + dont_generate_debug_code +} + +/* + * SCB Host Address + */ +register SCBHADDR { + address 0x07C + access_mode RW + size 8 + modes M_CCHAN + dont_generate_debug_code +} + +/* + * Scatter/Gather Host Count + */ +register SGHCNT { + address 0x084 + access_mode RW + modes M_DFF0, M_DFF1 + dont_generate_debug_code +} + +/* + * SCB Host Count + */ +register SCBHCNT { + address 0x084 + access_mode RW + modes M_CCHAN + dont_generate_debug_code +} + +/* + * Data FIFO Threshold + */ +register DFF_THRSH { + address 0x088 + access_mode RW + modes M_CFG + count 1 + field WR_DFTHRSH 0x70 { + WR_DFTHRSH_MIN, + WR_DFTHRSH_25, + WR_DFTHRSH_50, + WR_DFTHRSH_63, + WR_DFTHRSH_75, + WR_DFTHRSH_85, + WR_DFTHRSH_90, + WR_DFTHRSH_MAX + } + field RD_DFTHRSH 0x07 { + RD_DFTHRSH_MIN, + RD_DFTHRSH_25, + RD_DFTHRSH_50, + RD_DFTHRSH_63, + RD_DFTHRSH_75, + RD_DFTHRSH_85, + RD_DFTHRSH_90, + RD_DFTHRSH_MAX + } + dont_generate_debug_code +} + +/* + * ROM Address + */ +register ROMADDR { + address 0x08A + access_mode RW + size 3 +} + +/* + * ROM Control + */ +register ROMCNTRL { + address 0x08D + access_mode RW + field ROMOP 0xE0 + field ROMSPD 0x18 + field REPEAT 0x02 + field RDY 0x01 +} + +/* + * ROM Data + */ +register ROMDATA { + address 0x08E + access_mode RW +} + +/* + * Data Channel Receive Message 0 + */ +register DCHRXMSG0 { + address 0x090 + access_mode RO + modes M_DFF0, M_DFF1 + field CDNUM 0xF8 + field CFNUM 0x07 +} + +/* + * CMC Receive Message 0 + */ +register CMCRXMSG0 { + address 0x090 + access_mode RO + modes M_CCHAN + field CDNUM 0xF8 + field CFNUM 0x07 +} + +/* + * Overlay Receive Message 0 + */ +register OVLYRXMSG0 { + address 0x090 + access_mode RO + modes M_SCSI + field CDNUM 0xF8 + field CFNUM 0x07 +} + +/* + * Relaxed Order Enable + */ +register ROENABLE { + address 0x090 + access_mode RW + modes M_CFG + field MSIROEN 0x20 + field OVLYROEN 0x10 + field CMCROEN 0x08 + field SGROEN 0x04 + field DCH1ROEN 0x02 + field DCH0ROEN 0x01 +} + +/* + * Data Channel Receive Message 1 + */ +register DCHRXMSG1 { + address 0x091 + access_mode RO + modes M_DFF0, M_DFF1 + field CBNUM 0xFF +} + +/* + * CMC Receive Message 1 + */ +register CMCRXMSG1 { + address 0x091 + access_mode RO + modes M_CCHAN + field CBNUM 0xFF +} + +/* + * Overlay Receive Message 1 + */ +register OVLYRXMSG1 { + address 0x091 + access_mode RO + modes M_SCSI + field CBNUM 0xFF +} + +/* + * No Snoop Enable + */ +register NSENABLE { + address 0x091 + access_mode RW + modes M_CFG + field MSINSEN 0x20 + field OVLYNSEN 0x10 + field CMCNSEN 0x08 + field SGNSEN 0x04 + field DCH1NSEN 0x02 + field DCH0NSEN 0x01 +} + +/* + * Data Channel Receive Message 2 + */ +register DCHRXMSG2 { + address 0x092 + access_mode RO + modes M_DFF0, M_DFF1 + field MINDEX 0xFF +} + +/* + * CMC Receive Message 2 + */ +register CMCRXMSG2 { + address 0x092 + access_mode RO + modes M_CCHAN + field MINDEX 0xFF +} + +/* + * Overlay Receive Message 2 + */ +register OVLYRXMSG2 { + address 0x092 + access_mode RO + modes M_SCSI + field MINDEX 0xFF +} + +/* + * Outstanding Split Transactions + */ +register OST { + address 0x092 + access_mode RW + modes M_CFG +} + +/* + * Data Channel Receive Message 3 + */ +register DCHRXMSG3 { + address 0x093 + access_mode RO + modes M_DFF0, M_DFF1 + field MCLASS 0x0F +} + +/* + * CMC Receive Message 3 + */ +register CMCRXMSG3 { + address 0x093 + access_mode RO + modes M_CCHAN + field MCLASS 0x0F +} + +/* + * Overlay Receive Message 3 + */ +register OVLYRXMSG3 { + address 0x093 + access_mode RO + modes M_SCSI + field MCLASS 0x0F +} + +/* + * PCI-X Control + */ +register PCIXCTL { + address 0x093 + access_mode RW + modes M_CFG + count 1 + field SERRPULSE 0x80 + field UNEXPSCIEN 0x20 + field SPLTSMADIS 0x10 + field SPLTSTADIS 0x08 + field SRSPDPEEN 0x04 + field TSCSERREN 0x02 + field CMPABCDIS 0x01 + dont_generate_debug_code +} + +/* + * CMC Sequencer Byte Count + */ +register CMCSEQBCNT { + address 0x094 + access_mode RO + modes M_CCHAN +} + +/* + * Overlay Sequencer Byte Count + */ +register OVLYSEQBCNT { + address 0x094 + access_mode RO + modes M_SCSI +} + +/* + * Data Channel Sequencer Byte Count + */ +register DCHSEQBCNT { + address 0x094 + access_mode RO + size 2 + modes M_DFF0, M_DFF1 +} + +/* + * Data Channel Split Status 0 + */ +register DCHSPLTSTAT0 { + address 0x096 + access_mode RW + modes M_DFF0, M_DFF1 + count 2 + field STAETERM 0x80 + field SCBCERR 0x40 + field SCADERR 0x20 + field SCDATBUCKET 0x10 + field CNTNOTCMPLT 0x08 + field RXOVRUN 0x04 + field RXSCEMSG 0x02 + field RXSPLTRSP 0x01 + dont_generate_debug_code +} + +/* + * CMC Split Status 0 + */ +register CMCSPLTSTAT0 { + address 0x096 + access_mode RW + modes M_CCHAN + field STAETERM 0x80 + field SCBCERR 0x40 + field SCADERR 0x20 + field SCDATBUCKET 0x10 + field CNTNOTCMPLT 0x08 + field RXOVRUN 0x04 + field RXSCEMSG 0x02 + field RXSPLTRSP 0x01 +} + +/* + * Overlay Split Status 0 + */ +register OVLYSPLTSTAT0 { + address 0x096 + access_mode RW + modes M_SCSI + field STAETERM 0x80 + field SCBCERR 0x40 + field SCADERR 0x20 + field SCDATBUCKET 0x10 + field CNTNOTCMPLT 0x08 + field RXOVRUN 0x04 + field RXSCEMSG 0x02 + field RXSPLTRSP 0x01 +} + +/* + * Data Channel Split Status 1 + */ +register DCHSPLTSTAT1 { + address 0x097 + access_mode RW + modes M_DFF0, M_DFF1 + count 2 + field RXDATABUCKET 0x01 + dont_generate_debug_code +} + +/* + * CMC Split Status 1 + */ +register CMCSPLTSTAT1 { + address 0x097 + access_mode RW + modes M_CCHAN + field RXDATABUCKET 0x01 +} + +/* + * Overlay Split Status 1 + */ +register OVLYSPLTSTAT1 { + address 0x097 + access_mode RW + modes M_SCSI + field RXDATABUCKET 0x01 +} + +/* + * S/G Receive Message 0 + */ +register SGRXMSG0 { + address 0x098 + access_mode RO + modes M_DFF0, M_DFF1 + field CDNUM 0xF8 + field CFNUM 0x07 +} + +/* + * S/G Receive Message 1 + */ +register SGRXMSG1 { + address 0x099 + access_mode RO + modes M_DFF0, M_DFF1 + field CBNUM 0xFF +} + +/* + * S/G Receive Message 2 + */ +register SGRXMSG2 { + address 0x09A + access_mode RO + modes M_DFF0, M_DFF1 + field MINDEX 0xFF +} + +/* + * S/G Receive Message 3 + */ +register SGRXMSG3 { + address 0x09B + access_mode RO + modes M_DFF0, M_DFF1 + field MCLASS 0x0F +} + +/* + * Slave Split Out Address 0 + */ +register SLVSPLTOUTADR0 { + address 0x098 + access_mode RO + modes M_SCSI + field LOWER_ADDR 0x7F +} + +/* + * Slave Split Out Address 1 + */ +register SLVSPLTOUTADR1 { + address 0x099 + access_mode RO + modes M_SCSI + field REQ_DNUM 0xF8 + field REQ_FNUM 0x07 +} + +/* + * Slave Split Out Address 2 + */ +register SLVSPLTOUTADR2 { + address 0x09A + access_mode RO + modes M_SCSI + field REQ_BNUM 0xFF +} + +/* + * Slave Split Out Address 3 + */ +register SLVSPLTOUTADR3 { + address 0x09B + access_mode RO + modes M_SCSI + field RLXORD 020 + field TAG_NUM 0x1F +} + +/* + * SG Sequencer Byte Count + */ +register SGSEQBCNT { + address 0x09C + access_mode RO + modes M_DFF0, M_DFF1 +} + +/* + * Slave Split Out Attribute 0 + */ +register SLVSPLTOUTATTR0 { + address 0x09C + access_mode RO + modes M_SCSI + field LOWER_BCNT 0xFF +} + +/* + * Slave Split Out Attribute 1 + */ +register SLVSPLTOUTATTR1 { + address 0x09D + access_mode RO + modes M_SCSI + field CMPLT_DNUM 0xF8 + field CMPLT_FNUM 0x07 +} + +/* + * Slave Split Out Attribute 2 + */ +register SLVSPLTOUTATTR2 { + address 0x09E + access_mode RO + size 2 + modes M_SCSI + field CMPLT_BNUM 0xFF +} +/* + * S/G Split Status 0 + */ +register SGSPLTSTAT0 { + address 0x09E + access_mode RW + modes M_DFF0, M_DFF1 + count 2 + field STAETERM 0x80 + field SCBCERR 0x40 + field SCADERR 0x20 + field SCDATBUCKET 0x10 + field CNTNOTCMPLT 0x08 + field RXOVRUN 0x04 + field RXSCEMSG 0x02 + field RXSPLTRSP 0x01 + dont_generate_debug_code +} + +/* + * S/G Split Status 1 + */ +register SGSPLTSTAT1 { + address 0x09F + access_mode RW + modes M_DFF0, M_DFF1 + count 2 + field RXDATABUCKET 0x01 + dont_generate_debug_code +} + +/* + * Special Function + */ +register SFUNCT { + address 0x09f + access_mode RW + modes M_CFG + field TEST_GROUP 0xF0 + field TEST_NUM 0x0F + dont_generate_debug_code +} + +/* + * Data FIFO 0 PCI Status + */ +register DF0PCISTAT { + address 0x0A0 + access_mode RW + modes M_CFG + count 1 + field DPE 0x80 + field SSE 0x40 + field RMA 0x20 + field RTA 0x10 + field SCAAPERR 0x08 + field RDPERR 0x04 + field TWATERR 0x02 + field DPR 0x01 + dont_generate_debug_code +} + +/* + * Data FIFO 1 PCI Status + */ +register DF1PCISTAT { + address 0x0A1 + access_mode RW + modes M_CFG + field DPE 0x80 + field SSE 0x40 + field RMA 0x20 + field RTA 0x10 + field SCAAPERR 0x08 + field RDPERR 0x04 + field TWATERR 0x02 + field DPR 0x01 +} + +/* + * S/G PCI Status + */ +register SGPCISTAT { + address 0x0A2 + access_mode RW + modes M_CFG + field DPE 0x80 + field SSE 0x40 + field RMA 0x20 + field RTA 0x10 + field SCAAPERR 0x08 + field RDPERR 0x04 + field DPR 0x01 +} + +/* + * CMC PCI Status + */ +register CMCPCISTAT { + address 0x0A3 + access_mode RW + modes M_CFG + field DPE 0x80 + field SSE 0x40 + field RMA 0x20 + field RTA 0x10 + field SCAAPERR 0x08 + field RDPERR 0x04 + field TWATERR 0x02 + field DPR 0x01 +} + +/* + * Overlay PCI Status + */ +register OVLYPCISTAT { + address 0x0A4 + access_mode RW + modes M_CFG + field DPE 0x80 + field SSE 0x40 + field RMA 0x20 + field RTA 0x10 + field SCAAPERR 0x08 + field RDPERR 0x04 + field DPR 0x01 +} + +/* + * PCI Status for MSI Master DMA Transfer + */ +register MSIPCISTAT { + address 0x0A6 + access_mode RW + modes M_CFG + field SSE 0x40 + field RMA 0x20 + field RTA 0x10 + field CLRPENDMSI 0x08 + field TWATERR 0x02 + field DPR 0x01 +} + +/* + * PCI Status for Target + */ +register TARGPCISTAT { + address 0x0A7 + access_mode RW + modes M_CFG + count 5 + field DPE 0x80 + field SSE 0x40 + field STA 0x08 + field TWATERR 0x02 + dont_generate_debug_code +} + +/* + * LQ Packet In + * The last LQ Packet received + */ +register LQIN { + address 0x020 + access_mode RW + size 20 + count 2 + modes M_DFF0, M_DFF1, M_SCSI + dont_generate_debug_code +} + +/* + * SCB Type Pointer + * SCB offset for Target Mode SCB type information + */ +register TYPEPTR { + address 0x020 + access_mode RW + modes M_CFG +} + +/* + * Queue Tag Pointer + * SCB offset to the Two Byte tag identifier used for target mode. + */ +register TAGPTR { + address 0x021 + access_mode RW + modes M_CFG +} + +/* + * Logical Unit Number Pointer + * SCB offset to the LSB (little endian) of the lun field. + */ +register LUNPTR { + address 0x022 + access_mode RW + modes M_CFG + count 2 + dont_generate_debug_code +} + +/* + * Data Length Pointer + * SCB offset for the 4 byte data length field in target mode. + */ +register DATALENPTR { + address 0x023 + access_mode RW + modes M_CFG +} + +/* + * Status Length Pointer + * SCB offset to the two byte status field in target SCBs. + */ +register STATLENPTR { + address 0x024 + access_mode RW + modes M_CFG +} + +/* + * Command Length Pointer + * Scb offset for the CDB length field in initiator SCBs. + */ +register CMDLENPTR { + address 0x025 + access_mode RW + modes M_CFG + count 1 + dont_generate_debug_code +} + +/* + * Task Attribute Pointer + * Scb offset for the byte field specifying the attribute byte + * to be used in command packets. + */ +register ATTRPTR { + address 0x026 + access_mode RW + modes M_CFG + count 1 + dont_generate_debug_code +} + +/* + * Task Management Flags Pointer + * Scb offset for the byte field specifying the attribute flags + * byte to be used in command packets. + */ +register FLAGPTR { + address 0x027 + access_mode RW + modes M_CFG + count 1 + dont_generate_debug_code +} + +/* + * Command Pointer + * Scb offset for the first byte in the CDB for initiator SCBs. + */ +register CMDPTR { + address 0x028 + access_mode RW + modes M_CFG + count 1 + dont_generate_debug_code +} + +/* + * Queue Next Pointer + * Scb offset for the 2 byte "next scb link". + */ +register QNEXTPTR { + address 0x029 + access_mode RW + modes M_CFG + count 1 + dont_generate_debug_code +} + +/* + * SCSI ID Pointer + * Scb offset to the value to place in the SCSIID register + * during target mode connections. + */ +register IDPTR { + address 0x02A + access_mode RW + modes M_CFG +} + +/* + * Command Aborted Byte Pointer + * Offset to the SCB flags field that includes the + * "SCB aborted" status bit. + */ +register ABRTBYTEPTR { + address 0x02B + access_mode RW + modes M_CFG + count 1 + dont_generate_debug_code +} + +/* + * Command Aborted Bit Pointer + * Bit offset in the SCB flags field for "SCB aborted" status. + */ +register ABRTBITPTR { + address 0x02C + access_mode RW + modes M_CFG + count 1 + dont_generate_debug_code +} + +/* + * Rev B or greater. + */ +register MAXCMDBYTES { + address 0x02D + access_mode RW + modes M_CFG +} + +/* + * Rev B or greater. + */ +register MAXCMD2RCV { + address 0x02E + access_mode RW + modes M_CFG +} + +/* + * Rev B or greater. + */ +register SHORTTHRESH { + address 0x02F + access_mode RW + modes M_CFG +} + +/* + * Logical Unit Number Length + * The length, in bytes, of the SCB lun field. + */ +register LUNLEN { + address 0x030 + access_mode RW + modes M_CFG + count 2 + mask ILUNLEN 0x0F + mask TLUNLEN 0xF0 + dont_generate_debug_code +} +const LUNLEN_SINGLE_LEVEL_LUN 0xF + +/* + * CDB Limit + * The size, in bytes, of the embedded CDB field in initator SCBs. + */ +register CDBLIMIT { + address 0x031 + access_mode RW + modes M_CFG + count 1 + dont_generate_debug_code +} + +/* + * Maximum Commands + * The maximum number of commands to issue during a + * single packetized connection. + */ +register MAXCMD { + address 0x032 + access_mode RW + modes M_CFG + count 9 + dont_generate_debug_code +} + +/* + * Maximum Command Counter + * The number of commands already sent during this connection + */ +register MAXCMDCNT { + address 0x033 + access_mode RW + modes M_CFG + dont_generate_debug_code +} + +/* + * LQ Packet Reserved Bytes + * The bytes to be sent in the currently reserved fileds + * of all LQ packets. + */ +register LQRSVD01 { + address 0x034 + access_mode RW + modes M_SCSI +} +register LQRSVD16 { + address 0x035 + access_mode RW + modes M_SCSI +} +register LQRSVD17 { + address 0x036 + access_mode RW + modes M_SCSI +} + +/* + * Command Reserved 0 + * The byte to be sent for the reserved byte 0 of + * outgoing command packets. + */ +register CMDRSVD0 { + address 0x037 + access_mode RW + modes M_CFG +} + +/* + * LQ Manager Control 0 + */ +register LQCTL0 { + address 0x038 + access_mode RW + modes M_CFG + field LQITARGCLT 0xC0 + field LQIINITGCLT 0x30 + field LQ0TARGCLT 0x0C + field LQ0INITGCLT 0x03 +} + +/* + * LQ Manager Control 1 + */ +register LQCTL1 { + address 0x038 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + count 2 + field PCI2PCI 0x04 + field SINGLECMD 0x02 + field ABORTPENDING 0x01 + dont_generate_debug_code +} + +/* + * LQ Manager Control 2 + */ +register LQCTL2 { + address 0x039 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + count 5 + field LQIRETRY 0x80 + field LQICONTINUE 0x40 + field LQITOIDLE 0x20 + field LQIPAUSE 0x10 + field LQORETRY 0x08 + field LQOCONTINUE 0x04 + field LQOTOIDLE 0x02 + field LQOPAUSE 0x01 + dont_generate_debug_code +} + +/* + * SCSI RAM BIST0 + */ +register SCSBIST0 { + address 0x039 + access_mode RW + modes M_CFG + field GSBISTERR 0x40 + field GSBISTDONE 0x20 + field GSBISTRUN 0x10 + field OSBISTERR 0x04 + field OSBISTDONE 0x02 + field OSBISTRUN 0x01 +} + +/* + * SCSI Sequence Control0 + */ +register SCSISEQ0 { + address 0x03A + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + field TEMODEO 0x80 + field ENSELO 0x40 + field ENARBO 0x20 + field FORCEBUSFREE 0x10 + field SCSIRSTO 0x01 +} + +/* + * SCSI RAM BIST 1 + */ +register SCSBIST1 { + address 0x03A + access_mode RW + modes M_CFG + field NTBISTERR 0x04 + field NTBISTDONE 0x02 + field NTBISTRUN 0x01 +} + +/* + * SCSI Sequence Control 1 + */ +register SCSISEQ1 { + address 0x03B + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + count 8 + field MANUALCTL 0x40 + field ENSELI 0x20 + field ENRSELI 0x10 + field MANUALP 0x0C + field ENAUTOATNP 0x02 + field ALTSTIM 0x01 +} + +/* + * SCSI Transfer Control 0 + */ +register SXFRCTL0 { + address 0x03C + access_mode RW + modes M_SCSI + field DFON 0x80 + field DFPEXP 0x40 + field BIOSCANCELEN 0x10 + field SPIOEN 0x08 + dont_generate_debug_code +} + +/* + * SCSI Transfer Control 1 + */ +register SXFRCTL1 { + address 0x03D + access_mode RW + modes M_SCSI + field BITBUCKET 0x80 + field ENSACHK 0x40 + field ENSPCHK 0x20 + field STIMESEL 0x18 + field ENSTIMER 0x04 + field ACTNEGEN 0x02 + field STPWEN 0x01 + dont_generate_debug_code +} + +/* + * SCSI Transfer Control 2 + */ +register SXFRCTL2 { + address 0x03E + access_mode RW + modes M_SCSI + field AUTORSTDIS 0x10 + field CMDDMAEN 0x08 + field ASU 0x07 +} + +/* + * SCSI Bus Initiator IDs + * Bitmask of observed initiators on the bus. + */ +register BUSINITID { + address 0x03C + access_mode RW + modes M_CFG + size 2 +} + +/* + * Data Length Counters + * Packet byte counter. + */ +register DLCOUNT { + address 0x03C + access_mode RW + modes M_DFF0, M_DFF1 + size 3 +} + +/* + * Data FIFO Status + */ +register DFFSTAT { + address 0x03F + access_mode RW + modes M_SCSI + field FIFO1FREE 0x20 + field FIFO0FREE 0x10 + /* + * On the B, this enum only works + * in the read direction. For writes, + * you must use the B version of the + * CURRFIFO_0 definition which is defined + * as a constant outside of this register + * definition to avoid confusing the + * register pretty printing code. + */ + enum CURRFIFO 0x03 { + CURRFIFO_0, + CURRFIFO_1, + CURRFIFO_NONE 0x3 + } +} + +const B_CURRFIFO_0 0x2 + +/* + * SCSI Bus Target IDs + * Bitmask of observed targets on the bus. + */ +register BUSTARGID { + address 0x03E + access_mode RW + modes M_CFG + size 2 +} + +/* + * SCSI Control Signal Out + */ +register SCSISIGO { + address 0x040 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + field CDO 0x80 + field IOO 0x40 + field MSGO 0x20 + field ATNO 0x10 + field SELO 0x08 + field BSYO 0x04 + field REQO 0x02 + field ACKO 0x01 +/* + * Possible phases to write into SCSISIG0 + */ + enum PHASE_MASK CDO|IOO|MSGO { + P_DATAOUT 0x0, + P_DATAIN IOO, + P_DATAOUT_DT P_DATAOUT|MSGO, + P_DATAIN_DT P_DATAIN|MSGO, + P_COMMAND CDO, + P_MESGOUT CDO|MSGO, + P_STATUS CDO|IOO, + P_MESGIN CDO|IOO|MSGO + } + dont_generate_debug_code +} + +/* + * SCSI Control Signal In + */ +register SCSISIGI { + address 0x041 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field CDI 0x80 + field IOI 0x40 + field MSGI 0x20 + field ATNI 0x10 + field SELI 0x08 + field BSYI 0x04 + field REQI 0x02 + field ACKI 0x01 +/* + * Possible phases in SCSISIGI + */ + enum PHASE_MASK CDO|IOO|MSGO { + P_DATAOUT 0x0, + P_DATAIN IOO, + P_DATAOUT_DT P_DATAOUT|MSGO, + P_DATAIN_DT P_DATAIN|MSGO, + P_COMMAND CDO, + P_MESGOUT CDO|MSGO, + P_STATUS CDO|IOO, + P_MESGIN CDO|IOO|MSGO + } +} + +/* + * Multiple Target IDs + * Bitmask of ids to respond as a target. + */ +register MULTARGID { + address 0x040 + access_mode RW + modes M_CFG + size 2 + count 2 + dont_generate_debug_code +} + +/* + * SCSI Phase + */ +register SCSIPHASE { + address 0x042 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field STATUS_PHASE 0x20 + field COMMAND_PHASE 0x10 + field MSG_IN_PHASE 0x08 + field MSG_OUT_PHASE 0x04 + field DATA_PHASE_MASK 0x03 { + DATA_OUT_PHASE 0x01, + DATA_IN_PHASE 0x02 + } +} + +/* + * SCSI Data 0 Image + */ +register SCSIDAT0_IMG { + address 0x043 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI +} + +/* + * SCSI Latched Data + */ +register SCSIDAT { + address 0x044 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + size 2 + dont_generate_debug_code +} + +/* + * SCSI Data Bus + */ +register SCSIBUS { + address 0x046 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + size 2 +} + +/* + * Target ID In + */ +register TARGIDIN { + address 0x048 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + count 2 + field CLKOUT 0x80 + field TARGID 0x0F + dont_generate_debug_code +} + +/* + * Selection/Reselection ID + * Upper four bits are the device id. The ONEBIT is set when the re/selecting + * device did not set its own ID. + */ +register SELID { + address 0x049 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + field SELID_MASK 0xf0 + field ONEBIT 0x08 +} + +/* + * SCSI Block Control + * Controls Bus type and channel selection. SELWIDE allows for the + * coexistence of 8bit and 16bit devices on a wide bus. + */ +register SBLKCTL { + address 0x04A + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + field DIAGLEDEN 0x80 + field DIAGLEDON 0x40 + field ENAB40 0x08 /* LVD transceiver active */ + field ENAB20 0x04 /* SE/HVD transceiver active */ + field SELWIDE 0x02 + dont_generate_debug_code +} + +/* + * Option Mode + */ +register OPTIONMODE { + address 0x04A + access_mode RW + modes M_CFG + count 4 + field BIOSCANCTL 0x80 + field AUTOACKEN 0x40 + field BIASCANCTL 0x20 + field BUSFREEREV 0x10 + field ENDGFORMCHK 0x04 + field AUTO_MSGOUT_DE 0x02 + mask OPTIONMODE_DEFAULTS AUTO_MSGOUT_DE + dont_generate_debug_code +} + +/* + * SCSI Status 0 + */ +register SSTAT0 { + address 0x04B + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field TARGET 0x80 /* Board acting as target */ + field SELDO 0x40 /* Selection Done */ + field SELDI 0x20 /* Board has been selected */ + field SELINGO 0x10 /* Selection In Progress */ + field IOERR 0x08 /* LVD Tranceiver mode changed */ + field OVERRUN 0x04 /* SCSI Offset overrun detected */ + field SPIORDY 0x02 /* SCSI PIO Ready */ + field ARBDO 0x01 /* Arbitration Done Out */ +} + +/* + * Clear SCSI Interrupt 0 + * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT0. + */ +register CLRSINT0 { + address 0x04B + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + field CLRSELDO 0x40 + field CLRSELDI 0x20 + field CLRSELINGO 0x10 + field CLRIOERR 0x08 + field CLROVERRUN 0x04 + field CLRSPIORDY 0x02 + field CLRARBDO 0x01 + dont_generate_debug_code +} + +/* + * SCSI Interrupt Mode 0 + * Setting any bit will enable the corresponding function + * in SIMODE0 to interrupt via the IRQ pin. + */ +register SIMODE0 { + address 0x04B + access_mode RW + modes M_CFG + count 8 + field ENSELDO 0x40 + field ENSELDI 0x20 + field ENSELINGO 0x10 + field ENIOERR 0x08 + field ENOVERRUN 0x04 + field ENSPIORDY 0x02 + field ENARBDO 0x01 +} + +/* + * SCSI Status 1 + */ +register SSTAT1 { + address 0x04C + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field SELTO 0x80 + field ATNTARG 0x40 + field SCSIRSTI 0x20 + field PHASEMIS 0x10 + field BUSFREE 0x08 + field SCSIPERR 0x04 + field STRB2FAST 0x02 + field REQINIT 0x01 +} + +/* + * Clear SCSI Interrupt 1 + * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT1. + */ +register CLRSINT1 { + address 0x04C + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + field CLRSELTIMEO 0x80 + field CLRATNO 0x40 + field CLRSCSIRSTI 0x20 + field CLRBUSFREE 0x08 + field CLRSCSIPERR 0x04 + field CLRSTRB2FAST 0x02 + field CLRREQINIT 0x01 + dont_generate_debug_code +} + +/* + * SCSI Status 2 + */ +register SSTAT2 { + address 0x04d + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field BUSFREETIME 0xc0 { + BUSFREE_LQO 0x40, + BUSFREE_DFF0 0x80, + BUSFREE_DFF1 0xC0 + } + field NONPACKREQ 0x20 + field EXP_ACTIVE 0x10 /* SCSI Expander Active */ + field BSYX 0x08 /* Busy Expander */ + field WIDE_RES 0x04 /* Modes 0 and 1 only */ + field SDONE 0x02 /* Modes 0 and 1 only */ + field DMADONE 0x01 /* Modes 0 and 1 only */ +} + +/* + * Clear SCSI Interrupt 2 + */ +register CLRSINT2 { + address 0x04D + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + field CLRNONPACKREQ 0x20 + field CLRWIDE_RES 0x04 /* Modes 0 and 1 only */ + field CLRSDONE 0x02 /* Modes 0 and 1 only */ + field CLRDMADONE 0x01 /* Modes 0 and 1 only */ + dont_generate_debug_code +} + +/* + * SCSI Interrupt Mode 2 + */ +register SIMODE2 { + address 0x04D + access_mode RW + modes M_CFG + field ENWIDE_RES 0x04 + field ENSDONE 0x02 + field ENDMADONE 0x01 +} + +/* + * Physical Error Diagnosis + */ +register PERRDIAG { + address 0x04E + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + count 3 + field HIZERO 0x80 + field HIPERR 0x40 + field PREVPHASE 0x20 + field PARITYERR 0x10 + field AIPERR 0x08 + field CRCERR 0x04 + field DGFORMERR 0x02 + field DTERR 0x01 +} + +/* + * LQI Manager Current State + */ +register LQISTATE { + address 0x04E + access_mode RO + modes M_CFG + count 6 + dont_generate_debug_code +} + +/* + * SCSI Offset Count + */ +register SOFFCNT { + address 0x04F + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + count 1 +} + +/* + * LQO Manager Current State + */ +register LQOSTATE { + address 0x04F + access_mode RO + modes M_CFG + count 2 + dont_generate_debug_code +} + +/* + * LQI Manager Status + */ +register LQISTAT0 { + address 0x050 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + count 2 + field LQIATNQAS 0x20 + field LQICRCT1 0x10 + field LQICRCT2 0x08 + field LQIBADLQT 0x04 + field LQIATNLQ 0x02 + field LQIATNCMD 0x01 +} + +/* + * Clear LQI Interrupts 0 + */ +register CLRLQIINT0 { + address 0x050 + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + count 1 + field CLRLQIATNQAS 0x20 + field CLRLQICRCT1 0x10 + field CLRLQICRCT2 0x08 + field CLRLQIBADLQT 0x04 + field CLRLQIATNLQ 0x02 + field CLRLQIATNCMD 0x01 + dont_generate_debug_code +} + +/* + * LQI Manager Interrupt Mode 0 + */ +register LQIMODE0 { + address 0x050 + access_mode RW + modes M_CFG + count 3 + field ENLQIATNQASK 0x20 + field ENLQICRCT1 0x10 + field ENLQICRCT2 0x08 + field ENLQIBADLQT 0x04 + field ENLQIATNLQ 0x02 + field ENLQIATNCMD 0x01 + dont_generate_debug_code +} + +/* + * LQI Manager Status 1 + */ +register LQISTAT1 { + address 0x051 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + count 3 + field LQIPHASE_LQ 0x80 + field LQIPHASE_NLQ 0x40 + field LQIABORT 0x20 + field LQICRCI_LQ 0x10 + field LQICRCI_NLQ 0x08 + field LQIBADLQI 0x04 + field LQIOVERI_LQ 0x02 + field LQIOVERI_NLQ 0x01 +} + +/* + * Clear LQI Manager Interrupts1 + */ +register CLRLQIINT1 { + address 0x051 + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + count 4 + field CLRLQIPHASE_LQ 0x80 + field CLRLQIPHASE_NLQ 0x40 + field CLRLIQABORT 0x20 + field CLRLQICRCI_LQ 0x10 + field CLRLQICRCI_NLQ 0x08 + field CLRLQIBADLQI 0x04 + field CLRLQIOVERI_LQ 0x02 + field CLRLQIOVERI_NLQ 0x01 + dont_generate_debug_code +} + +/* + * LQI Manager Interrupt Mode 1 + */ +register LQIMODE1 { + address 0x051 + access_mode RW + modes M_CFG + count 4 + field ENLQIPHASE_LQ 0x80 /* LQIPHASE1 */ + field ENLQIPHASE_NLQ 0x40 /* LQIPHASE2 */ + field ENLIQABORT 0x20 + field ENLQICRCI_LQ 0x10 /* LQICRCI1 */ + field ENLQICRCI_NLQ 0x08 /* LQICRCI2 */ + field ENLQIBADLQI 0x04 + field ENLQIOVERI_LQ 0x02 /* LQIOVERI1 */ + field ENLQIOVERI_NLQ 0x01 /* LQIOVERI2 */ + dont_generate_debug_code +} + +/* + * LQI Manager Status 2 + */ +register LQISTAT2 { + address 0x052 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field PACKETIZED 0x80 + field LQIPHASE_OUTPKT 0x40 + field LQIWORKONLQ 0x20 + field LQIWAITFIFO 0x10 + field LQISTOPPKT 0x08 + field LQISTOPLQ 0x04 + field LQISTOPCMD 0x02 + field LQIGSAVAIL 0x01 +} + +/* + * SCSI Status 3 + */ +register SSTAT3 { + address 0x053 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + count 3 + field NTRAMPERR 0x02 + field OSRAMPERR 0x01 +} + +/* + * Clear SCSI Status 3 + */ +register CLRSINT3 { + address 0x053 + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + count 3 + field CLRNTRAMPERR 0x02 + field CLROSRAMPERR 0x01 + dont_generate_debug_code +} + +/* + * SCSI Interrupt Mode 3 + */ +register SIMODE3 { + address 0x053 + access_mode RW + modes M_CFG + count 4 + field ENNTRAMPERR 0x02 + field ENOSRAMPERR 0x01 + dont_generate_debug_code +} + +/* + * LQO Manager Status 0 + */ +register LQOSTAT0 { + address 0x054 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + count 2 + field LQOTARGSCBPERR 0x10 + field LQOSTOPT2 0x08 + field LQOATNLQ 0x04 + field LQOATNPKT 0x02 + field LQOTCRC 0x01 +} + +/* + * Clear LQO Manager interrupt 0 + */ +register CLRLQOINT0 { + address 0x054 + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + count 3 + field CLRLQOTARGSCBPERR 0x10 + field CLRLQOSTOPT2 0x08 + field CLRLQOATNLQ 0x04 + field CLRLQOATNPKT 0x02 + field CLRLQOTCRC 0x01 + dont_generate_debug_code +} + +/* + * LQO Manager Interrupt Mode 0 + */ +register LQOMODE0 { + address 0x054 + access_mode RW + modes M_CFG + count 4 + field ENLQOTARGSCBPERR 0x10 + field ENLQOSTOPT2 0x08 + field ENLQOATNLQ 0x04 + field ENLQOATNPKT 0x02 + field ENLQOTCRC 0x01 + dont_generate_debug_code +} + +/* + * LQO Manager Status 1 + */ +register LQOSTAT1 { + address 0x055 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field LQOINITSCBPERR 0x10 + field LQOSTOPI2 0x08 + field LQOBADQAS 0x04 + field LQOBUSFREE 0x02 + field LQOPHACHGINPKT 0x01 +} + +/* + * Clear LOQ Interrupt 1 + */ +register CLRLQOINT1 { + address 0x055 + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + count 7 + field CLRLQOINITSCBPERR 0x10 + field CLRLQOSTOPI2 0x08 + field CLRLQOBADQAS 0x04 + field CLRLQOBUSFREE 0x02 + field CLRLQOPHACHGINPKT 0x01 + dont_generate_debug_code +} + +/* + * LQO Manager Interrupt Mode 1 + */ +register LQOMODE1 { + address 0x055 + access_mode RW + modes M_CFG + count 4 + field ENLQOINITSCBPERR 0x10 + field ENLQOSTOPI2 0x08 + field ENLQOBADQAS 0x04 + field ENLQOBUSFREE 0x02 + field ENLQOPHACHGINPKT 0x01 + dont_generate_debug_code +} + +/* + * LQO Manager Status 2 + */ +register LQOSTAT2 { + address 0x056 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field LQOPKT 0xE0 + field LQOWAITFIFO 0x10 + field LQOPHACHGOUTPKT 0x02 /* outside of packet boundaries. */ + field LQOSTOP0 0x01 /* Stopped after sending all packets */ +} + +/* + * Output Synchronizer Space Count + */ +register OS_SPACE_CNT { + address 0x056 + access_mode RO + modes M_CFG + count 2 + dont_generate_debug_code +} + +/* + * SCSI Interrupt Mode 1 + * Setting any bit will enable the corresponding function + * in SIMODE1 to interrupt via the IRQ pin. + */ +register SIMODE1 { + address 0x057 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + field ENSELTIMO 0x80 + field ENATNTARG 0x40 + field ENSCSIRST 0x20 + field ENPHASEMIS 0x10 + field ENBUSFREE 0x08 + field ENSCSIPERR 0x04 + field ENSTRB2FAST 0x02 + field ENREQINIT 0x01 +} + +/* + * Good Status FIFO + */ +register GSFIFO { + address 0x058 + access_mode RO + size 2 + modes M_DFF0, M_DFF1, M_SCSI + dont_generate_debug_code +} + +/* + * Data FIFO SCSI Transfer Control + */ +register DFFSXFRCTL { + address 0x05A + access_mode RW + modes M_DFF0, M_DFF1 + field DFFBITBUCKET 0x08 + field CLRSHCNT 0x04 + field CLRCHN 0x02 + field RSTCHN 0x01 +} + +/* + * Next SCSI Control Block + */ +register NEXTSCB { + address 0x05A + access_mode RW + size 2 + modes M_SCSI + dont_generate_debug_code +} + +/* + * LQO SCSI Control + * (Rev B only.) + */ +register LQOSCSCTL { + address 0x05A + access_mode RW + size 1 + modes M_CFG + count 1 + field LQOH2A_VERSION 0x80 + field LQOBUSETDLY 0x40 + field LQONOHOLDLACK 0x02 + field LQONOCHKOVER 0x01 + dont_generate_debug_code +} + +/* + * SEQ Interrupts + */ +register SEQINTSRC { + address 0x05B + access_mode RO + modes M_DFF0, M_DFF1 + field CTXTDONE 0x40 + field SAVEPTRS 0x20 + field CFG4DATA 0x10 + field CFG4ISTAT 0x08 + field CFG4TSTAT 0x04 + field CFG4ICMD 0x02 + field CFG4TCMD 0x01 +} + +/* + * Clear Arp Interrupts + */ +register CLRSEQINTSRC { + address 0x05B + access_mode WO + modes M_DFF0, M_DFF1 + field CLRCTXTDONE 0x40 + field CLRSAVEPTRS 0x20 + field CLRCFG4DATA 0x10 + field CLRCFG4ISTAT 0x08 + field CLRCFG4TSTAT 0x04 + field CLRCFG4ICMD 0x02 + field CLRCFG4TCMD 0x01 + dont_generate_debug_code +} + +/* + * SEQ Interrupt Enabled (Shared) + */ +register SEQIMODE { + address 0x05C + access_mode RW + modes M_DFF0, M_DFF1 + field ENCTXTDONE 0x40 + field ENSAVEPTRS 0x20 + field ENCFG4DATA 0x10 + field ENCFG4ISTAT 0x08 + field ENCFG4TSTAT 0x04 + field ENCFG4ICMD 0x02 + field ENCFG4TCMD 0x01 +} + +/* + * Current SCSI Control Block + */ +register CURRSCB { + address 0x05C + access_mode RW + size 2 + modes M_SCSI + dont_generate_debug_code +} + +/* + * Data FIFO Status + */ +register MDFFSTAT { + address 0x05D + access_mode RO + modes M_DFF0, M_DFF1 + field SHCNTNEGATIVE 0x40 /* Rev B or higher */ + field SHCNTMINUS1 0x20 /* Rev B or higher */ + field LASTSDONE 0x10 + field SHVALID 0x08 + field DLZERO 0x04 /* FIFO data ends on packet boundary. */ + field DATAINFIFO 0x02 + field FIFOFREE 0x01 +} + +/* + * CRC Control + */ +register CRCCONTROL { + address 0x05d + access_mode RW + modes M_CFG + field CRCVALCHKEN 0x40 +} + +/* + * SCSI Test Control + */ +register SCSITEST { + address 0x05E + access_mode RW + modes M_CFG + field CNTRTEST 0x08 + field SEL_TXPLL_DEBUG 0x04 +} + +/* + * Data FIFO Queue Tag + */ +register DFFTAG { + address 0x05E + access_mode RW + size 2 + modes M_DFF0, M_DFF1 +} + +/* + * Last SCSI Control Block + */ +register LASTSCB { + address 0x05E + access_mode RW + size 2 + modes M_SCSI + dont_generate_debug_code +} + +/* + * SCSI I/O Cell Power-down Control + */ +register IOPDNCTL { + address 0x05F + access_mode RW + modes M_CFG + field DISABLE_OE 0x80 + field PDN_IDIST 0x04 + field PDN_DIFFSENSE 0x01 +} + +/* + * Shadow Host Address. + */ +register SHADDR { + address 0x060 + access_mode RO + size 8 + modes M_DFF0, M_DFF1 + dont_generate_debug_code +} + +/* + * Data Group CRC Interval. + */ +register DGRPCRCI { + address 0x060 + access_mode RW + size 2 + modes M_CFG +} + +/* + * Data Transfer Negotiation Address + */ +register NEGOADDR { + address 0x060 + access_mode RW + modes M_SCSI + dont_generate_debug_code +} + +/* + * Data Transfer Negotiation Data - Period Byte + */ +register NEGPERIOD { + address 0x061 + access_mode RW + modes M_SCSI + count 1 + dont_generate_debug_code +} + +/* + * Packetized CRC Interval + */ +register PACKCRCI { + address 0x062 + access_mode RW + size 2 + modes M_CFG +} + +/* + * Data Transfer Negotiation Data - Offset Byte + */ +register NEGOFFSET { + address 0x062 + access_mode RW + modes M_SCSI + count 1 + dont_generate_debug_code +} + +/* + * Data Transfer Negotiation Data - PPR Options + */ +register NEGPPROPTS { + address 0x063 + access_mode RW + modes M_SCSI + count 1 + field PPROPT_PACE 0x08 + field PPROPT_QAS 0x04 + field PPROPT_DT 0x02 + field PPROPT_IUT 0x01 + dont_generate_debug_code +} + +/* + * Data Transfer Negotiation Data - Connection Options + */ +register NEGCONOPTS { + address 0x064 + access_mode RW + modes M_SCSI + field ENSNAPSHOT 0x40 + field RTI_WRTDIS 0x20 + field RTI_OVRDTRN 0x10 + field ENSLOWCRC 0x08 + field ENAUTOATNI 0x04 + field ENAUTOATNO 0x02 + field WIDEXFER 0x01 + dont_generate_debug_code +} + +/* + * Negotiation Table Annex Column Index. + */ +register ANNEXCOL { + address 0x065 + access_mode RW + modes M_SCSI + count 7 + dont_generate_debug_code +} + +/* + * SCSI Check + * (Rev. B only) + */ +register SCSCHKN { + address 0x066 + access_mode RW + modes M_CFG + count 1 + field BIDICHKDIS 0x80 + field STSELSKIDDIS 0x40 + field CURRFIFODEF 0x20 + field WIDERESEN 0x10 + field SDONEMSKDIS 0x08 + field DFFACTCLR 0x04 + field SHVALIDSTDIS 0x02 + field LSTSGCLRDIS 0x01 + dont_generate_debug_code +} + +const AHD_ANNEXCOL_PER_DEV0 4 +const AHD_NUM_PER_DEV_ANNEXCOLS 4 +const AHD_ANNEXCOL_PRECOMP_SLEW 4 +const AHD_PRECOMP_MASK 0x07 +const AHD_PRECOMP_SHIFT 0 +const AHD_PRECOMP_CUTBACK_17 0x04 +const AHD_PRECOMP_CUTBACK_29 0x06 +const AHD_PRECOMP_CUTBACK_37 0x07 +const AHD_SLEWRATE_MASK 0x78 +const AHD_SLEWRATE_SHIFT 3 +/* + * Rev A has only a single bit (high bit of field) of slew adjustment. + * Rev B has 4 bits. The current default happens to be the same for both. + */ +const AHD_SLEWRATE_DEF_REVA 0x08 +const AHD_SLEWRATE_DEF_REVB 0x08 + +/* Rev A does not have any amplitude setting. */ +const AHD_ANNEXCOL_AMPLITUDE 6 +const AHD_AMPLITUDE_MASK 0x7 +const AHD_AMPLITUDE_SHIFT 0 +const AHD_AMPLITUDE_DEF 0x7 + +/* + * Negotiation Table Annex Data Port. + */ +register ANNEXDAT { + address 0x066 + access_mode RW + modes M_SCSI + count 3 + dont_generate_debug_code +} + +/* + * Initiator's Own Id. + * The SCSI ID to use for Selection Out and seen during a reselection.. + */ +register IOWNID { + address 0x067 + access_mode RW + modes M_SCSI + dont_generate_debug_code +} + +/* + * 960MHz Phase-Locked Loop Control 0 + */ +register PLL960CTL0 { + address 0x068 + access_mode RW + modes M_CFG + field PLL_VCOSEL 0x80 + field PLL_PWDN 0x40 + field PLL_NS 0x30 + field PLL_ENLUD 0x08 + field PLL_ENLPF 0x04 + field PLL_DLPF 0x02 + field PLL_ENFBM 0x01 +} + +/* + * Target Own Id + */ +register TOWNID { + address 0x069 + access_mode RW + modes M_SCSI + count 2 + dont_generate_debug_code +} + +/* + * 960MHz Phase-Locked Loop Control 1 + */ +register PLL960CTL1 { + address 0x069 + access_mode RW + modes M_CFG + field PLL_CNTEN 0x80 + field PLL_CNTCLR 0x40 + field PLL_RST 0x01 +} + +/* + * Expander Signature + */ +register XSIG { + address 0x06A + access_mode RW + modes M_SCSI +} + +/* + * Shadow Byte Count + */ +register SHCNT { + address 0x068 + access_mode RW + size 3 + modes M_DFF0, M_DFF1 + dont_generate_debug_code +} + +/* + * Selection Out ID + */ +register SELOID { + address 0x06B + access_mode RW + modes M_SCSI +} + +/* + * 960-MHz Phase-Locked Loop Test Count + */ +register PLL960CNT0 { + address 0x06A + access_mode RO + size 2 + modes M_CFG +} + +/* + * 400-MHz Phase-Locked Loop Control 0 + */ +register PLL400CTL0 { + address 0x06C + access_mode RW + modes M_CFG + field PLL_VCOSEL 0x80 + field PLL_PWDN 0x40 + field PLL_NS 0x30 + field PLL_ENLUD 0x08 + field PLL_ENLPF 0x04 + field PLL_DLPF 0x02 + field PLL_ENFBM 0x01 +} + +/* + * Arbitration Fairness + */ +register FAIRNESS { + address 0x06C + access_mode RW + size 2 + modes M_SCSI +} + +/* + * 400-MHz Phase-Locked Loop Control 1 + */ +register PLL400CTL1 { + address 0x06D + access_mode RW + modes M_CFG + field PLL_CNTEN 0x80 + field PLL_CNTCLR 0x40 + field PLL_RST 0x01 +} + +/* + * Arbitration Unfairness + */ +register UNFAIRNESS { + address 0x06E + access_mode RW + size 2 + modes M_SCSI +} + +/* + * 400-MHz Phase-Locked Loop Test Count + */ +register PLL400CNT0 { + address 0x06E + access_mode RO + size 2 + modes M_CFG +} + +/* + * SCB Page Pointer + */ +register SCBPTR { + address 0x0A8 + access_mode RW + size 2 + modes M_DFF0, M_DFF1, M_CCHAN, M_SCSI + dont_generate_debug_code +} + +/* + * CMC SCB Array Count + * Number of bytes to transfer between CMC SCB memory and SCBRAM. + * Transfers must be 8byte aligned and sized. + */ +register CCSCBACNT { + address 0x0AB + access_mode RW + modes M_CCHAN +} + +/* + * SCB Autopointer + * SCB-Next Address Snooping logic. When an SCB is transferred to + * the card, the next SCB address to be used by the CMC array can + * be autoloaded from that transfer. + */ +register SCBAUTOPTR { + address 0x0AB + access_mode RW + modes M_CFG + count 1 + field AUSCBPTR_EN 0x80 + field SCBPTR_ADDR 0x38 + field SCBPTR_OFF 0x07 + dont_generate_debug_code +} + +/* + * CMC SG Ram Address Pointer + */ +register CCSGADDR { + address 0x0AC + access_mode RW + modes M_DFF0, M_DFF1 + dont_generate_debug_code +} + +/* + * CMC SCB RAM Address Pointer + */ +register CCSCBADDR { + address 0x0AC + access_mode RW + modes M_CCHAN + dont_generate_debug_code +} + +/* + * CMC SCB Ram Back-up Address Pointer + * Indicates the true stop location of transfers halted prior + * to SCBHCNT going to 0. + */ +register CCSCBADR_BK { + address 0x0AC + access_mode RO + modes M_CFG +} + +/* + * CMC SG Control + */ +register CCSGCTL { + address 0x0AD + access_mode RW + modes M_DFF0, M_DFF1 + field CCSGDONE 0x80 + field SG_CACHE_AVAIL 0x10 + field CCSGENACK 0x08 + mask CCSGEN 0x0C + field SG_FETCH_REQ 0x02 + field CCSGRESET 0x01 +} + +/* + * CMD SCB Control + */ +register CCSCBCTL { + address 0x0AD + access_mode RW + modes M_CCHAN + field CCSCBDONE 0x80 + field ARRDONE 0x40 + field CCARREN 0x10 + field CCSCBEN 0x08 + field CCSCBDIR 0x04 + field CCSCBRESET 0x01 +} + +/* + * CMC Ram BIST + */ +register CMC_RAMBIST { + address 0x0AD + access_mode RW + modes M_CFG + field SG_ELEMENT_SIZE 0x80 + field SCBRAMBIST_FAIL 0x40 + field SG_BIST_FAIL 0x20 + field SG_BIST_EN 0x10 + field CMC_BUFFER_BIST_FAIL 0x02 + field CMC_BUFFER_BIST_EN 0x01 +} + +/* + * CMC SG RAM Data Port + */ +register CCSGRAM { + address 0x0B0 + access_mode RW + modes M_DFF0, M_DFF1 + dont_generate_debug_code +} + +/* + * CMC SCB RAM Data Port + */ +register CCSCBRAM { + address 0x0B0 + access_mode RW + modes M_CCHAN + dont_generate_debug_code +} + +/* + * Flex DMA Address. + */ +register FLEXADR { + address 0x0B0 + access_mode RW + size 3 + modes M_SCSI +} + +/* + * Flex DMA Byte Count + */ +register FLEXCNT { + address 0x0B3 + access_mode RW + size 2 + modes M_SCSI +} + +/* + * Flex DMA Status + */ +register FLEXDMASTAT { + address 0x0B5 + access_mode RW + modes M_SCSI + field FLEXDMAERR 0x02 + field FLEXDMADONE 0x01 +} + +/* + * Flex DMA Data Port + */ +register FLEXDATA { + address 0x0B6 + access_mode RW + modes M_SCSI +} + +/* + * Board Data + */ +register BRDDAT { + address 0x0B8 + access_mode RW + modes M_SCSI + count 2 + dont_generate_debug_code +} + +/* + * Board Control + */ +register BRDCTL { + address 0x0B9 + access_mode RW + modes M_SCSI + count 7 + field FLXARBACK 0x80 + field FLXARBREQ 0x40 + field BRDADDR 0x38 + field BRDEN 0x04 + field BRDRW 0x02 + field BRDSTB 0x01 + dont_generate_debug_code +} + +/* + * Serial EEPROM Address + */ +register SEEADR { + address 0x0BA + access_mode RW + modes M_SCSI + count 4 + dont_generate_debug_code +} + +/* + * Serial EEPROM Data + */ +register SEEDAT { + address 0x0BC + access_mode RW + size 2 + modes M_SCSI + count 4 + dont_generate_debug_code +} + +/* + * Serial EEPROM Status + */ +register SEESTAT { + address 0x0BE + access_mode RO + modes M_SCSI + count 1 + field INIT_DONE 0x80 + field SEEOPCODE 0x70 + field LDALTID_L 0x08 + field SEEARBACK 0x04 + field SEEBUSY 0x02 + field SEESTART 0x01 + dont_generate_debug_code +} + +/* + * Serial EEPROM Control + */ +register SEECTL { + address 0x0BE + access_mode RW + modes M_SCSI + count 4 + field SEEOPCODE 0x70 { + SEEOP_ERASE 0x70, + SEEOP_READ 0x60, + SEEOP_WRITE 0x50, + /* + * The following four commands use special + * addresses for differentiation. + */ + SEEOP_ERAL 0x40 + } + mask SEEOP_EWEN 0x40 + mask SEEOP_WALL 0x40 + mask SEEOP_EWDS 0x40 + field SEERST 0x02 + field SEESTART 0x01 + dont_generate_debug_code +} + +const SEEOP_ERAL_ADDR 0x80 +const SEEOP_EWEN_ADDR 0xC0 +const SEEOP_WRAL_ADDR 0x40 +const SEEOP_EWDS_ADDR 0x00 + +/* + * SCB Counter + */ +register SCBCNT { + address 0x0BF + access_mode RW + modes M_SCSI + dont_generate_debug_code +} + +/* + * Data FIFO Write Address + * Pointer to the next QWD location to be written to the data FIFO. + */ +register DFWADDR { + address 0x0C0 + access_mode RW + size 2 + modes M_DFF0, M_DFF1 + dont_generate_debug_code +} + +/* + * DSP Filter Control + */ +register DSPFLTRCTL { + address 0x0C0 + access_mode RW + modes M_CFG + field FLTRDISABLE 0x20 + field EDGESENSE 0x10 + field DSPFCNTSEL 0x0F +} + +/* + * DSP Data Channel Control + */ +register DSPDATACTL { + address 0x0C1 + access_mode RW + modes M_CFG + count 3 + field BYPASSENAB 0x80 + field DESQDIS 0x10 + field RCVROFFSTDIS 0x04 + field XMITOFFSTDIS 0x02 + dont_generate_debug_code +} + +/* + * Data FIFO Read Address + * Pointer to the next QWD location to be read from the data FIFO. + */ +register DFRADDR { + address 0x0C2 + access_mode RW + size 2 + modes M_DFF0, M_DFF1 +} + +/* + * DSP REQ Control + */ +register DSPREQCTL { + address 0x0C2 + access_mode RW + modes M_CFG + field MANREQCTL 0xC0 + field MANREQDLY 0x3F +} + +/* + * DSP ACK Control + */ +register DSPACKCTL { + address 0x0C3 + access_mode RW + modes M_CFG + field MANACKCTL 0xC0 + field MANACKDLY 0x3F +} + +/* + * Data FIFO Data + * Read/Write byte port into the data FIFO. The read and write + * FIFO pointers increment with each read and write respectively + * to this port. + */ +register DFDAT { + address 0x0C4 + access_mode RW + modes M_DFF0, M_DFF1 + dont_generate_debug_code +} + +/* + * DSP Channel Select + */ +register DSPSELECT { + address 0x0C4 + access_mode RW + modes M_CFG + count 1 + field AUTOINCEN 0x80 + field DSPSEL 0x1F + dont_generate_debug_code +} + +const NUMDSPS 0x14 + +/* + * Write Bias Control + */ +register WRTBIASCTL { + address 0x0C5 + access_mode WO + modes M_CFG + count 3 + field AUTOXBCDIS 0x80 + field XMITMANVAL 0x3F + dont_generate_debug_code +} + +/* + * Currently the WRTBIASCTL is the same as the default. + */ +const WRTBIASCTL_HP_DEFAULT 0x0 + +/* + * Receiver Bias Control + */ +register RCVRBIOSCTL { + address 0x0C6 + access_mode WO + modes M_CFG + field AUTORBCDIS 0x80 + field RCVRMANVAL 0x3F +} + +/* + * Write Bias Calculator + */ +register WRTBIASCALC { + address 0x0C7 + access_mode RO + modes M_CFG +} + +/* + * Data FIFO Pointers + * Contains the byte offset from DFWADDR and DWRADDR to the current + * FIFO write/read locations. + */ +register DFPTRS { + address 0x0C8 + access_mode RW + modes M_DFF0, M_DFF1 +} + +/* + * Receiver Bias Calculator + */ +register RCVRBIASCALC { + address 0x0C8 + access_mode RO + modes M_CFG +} + +/* + * Data FIFO Backup Read Pointer + * Contains the data FIFO address to be restored if the last + * data accessed from the data FIFO was not transferred successfully. + */ +register DFBKPTR { + address 0x0C9 + access_mode RW + size 2 + modes M_DFF0, M_DFF1 +} + +/* + * Skew Calculator + */ +register SKEWCALC { + address 0x0C9 + access_mode RO + modes M_CFG +} + +/* + * Data FIFO Debug Control + */ +register DFDBCTL { + address 0x0CB + access_mode RW + modes M_DFF0, M_DFF1 + field DFF_CIO_WR_RDY 0x20 + field DFF_CIO_RD_RDY 0x10 + field DFF_DIR_ERR 0x08 + field DFF_RAMBIST_FAIL 0x04 + field DFF_RAMBIST_DONE 0x02 + field DFF_RAMBIST_EN 0x01 +} + +/* + * Data FIFO Space Count + * Number of FIFO locations that are free. + */ +register DFSCNT { + address 0x0CC + access_mode RO + size 2 + modes M_DFF0, M_DFF1 +} + +/* + * Data FIFO Byte Count + * Number of filled FIFO locations. + */ +register DFBCNT { + address 0x0CE + access_mode RO + size 2 + modes M_DFF0, M_DFF1 +} + +/* + * Sequencer Program Overlay Address. + * Low address must be written prior to high address. + */ +register OVLYADDR { + address 0x0D4 + modes M_SCSI + size 2 + access_mode RW +} + +/* + * Sequencer Control 0 + * Error detection mode, speed configuration, + * single step, breakpoints and program load. + */ +register SEQCTL0 { + address 0x0D6 + access_mode RW + count 11 + field PERRORDIS 0x80 + field PAUSEDIS 0x40 + field FAILDIS 0x20 + field FASTMODE 0x10 + field BRKADRINTEN 0x08 + field STEP 0x04 + field SEQRESET 0x02 + field LOADRAM 0x01 +} + +/* + * Sequencer Control 1 + * Instruction RAM Diagnostics + */ +register SEQCTL1 { + address 0x0D7 + access_mode RW + field OVRLAY_DATA_CHK 0x08 + field RAMBIST_DONE 0x04 + field RAMBIST_FAIL 0x02 + field RAMBIST_EN 0x01 +} + +/* + * Sequencer Flags + * Zero and Carry state of the ALU. + */ +register FLAGS { + address 0x0D8 + access_mode RO + count 23 + field ZERO 0x02 + field CARRY 0x01 + dont_generate_debug_code +} + +/* + * Sequencer Interrupt Control + */ +register SEQINTCTL { + address 0x0D9 + access_mode RW + field INTVEC1DSL 0x80 + field INT1_CONTEXT 0x20 + field SCS_SEQ_INT1M1 0x10 + field SCS_SEQ_INT1M0 0x08 + field INTMASK2 0x04 + field INTMASK1 0x02 + field IRET 0x01 +} + +/* + * Sequencer RAM Data Port + * Single byte window into the Sequencer Instruction Ram area starting + * at the address specified by OVLYADDR. To write a full instruction word, + * simply write four bytes in succession. OVLYADDR will increment after the + * most significant instrution byte (the byte with the parity bit) is written. + */ +register SEQRAM { + address 0x0DA + access_mode RW + count 2 + dont_generate_debug_code +} + +/* + * Sequencer Program Counter + * Low byte must be written prior to high byte. + */ +register PRGMCNT { + address 0x0DE + access_mode RW + size 2 + count 5 + dont_generate_debug_code +} + +/* + * Accumulator + */ +register ACCUM { + address 0x0E0 + access_mode RW + accumulator + dont_generate_debug_code +} + +/* + * Source Index Register + * Incrementing index for reads of SINDIR and the destination (low byte only) + * for any immediate operands passed in jmp, jc, jnc, call instructions. + * Example: + * mvi 0xFF call some_routine; + * + * Will set SINDEX[0] to 0xFF and call the routine "some_routine. + */ +register SINDEX { + address 0x0E2 + access_mode RW + size 2 + sindex + dont_generate_debug_code +} + +/* + * Destination Index Register + * Incrementing index for writes to DINDIR. Can be used as a scratch register. + */ +register DINDEX { + address 0x0E4 + access_mode RW + size 2 + dont_generate_debug_code +} + +/* + * Break Address + * Sequencer instruction breakpoint address address. + */ +register BRKADDR0 { + address 0x0E6 + access_mode RW +} + +register BRKADDR1 { + address 0x0E6 + access_mode RW + field BRKDIS 0x80 /* Disable Breakpoint */ +} + +/* + * All Ones + * All reads to this register return the value 0xFF. + */ +register ALLONES { + address 0x0E8 + access_mode RO + allones + dont_generate_debug_code +} + +/* + * All Zeros + * All reads to this register return the value 0. + */ +register ALLZEROS { + address 0x0EA + access_mode RO + allzeros + dont_generate_debug_code +} + +/* + * No Destination + * Writes to this register have no effect. + */ +register NONE { + address 0x0EA + access_mode WO + none + dont_generate_debug_code +} + +/* + * Source Index Indirect + * Reading this register is equivalent to reading (register_base + SINDEX) and + * incrementing SINDEX by 1. + */ +register SINDIR { + address 0x0EC + access_mode RO + dont_generate_debug_code +} + +/* + * Destination Index Indirect + * Writing this register is equivalent to writing to (register_base + DINDEX) + * and incrementing DINDEX by 1. + */ +register DINDIR { + address 0x0ED + access_mode WO + dont_generate_debug_code +} + +/* + * Function One + * 2's complement to bit value conversion. Write the 2's complement value + * (0-7 only) to the top nibble and retrieve the bit indexed by that value + * on the next read of this register. + * Example: + * Write 0x60 + * Read 0x40 + */ +register FUNCTION1 { + address 0x0F0 + access_mode RW +} + +/* + * Stack + * Window into the stack. Each stack location is 10 bits wide reported + * low byte followed by high byte. There are 8 stack locations. + */ +register STACK { + address 0x0F2 + access_mode RW + dont_generate_debug_code +} + +/* + * Interrupt Vector 1 Address + * Interrupt branch address for SCS SEQ_INT1 mode 0 and 1 interrupts. + */ +register INTVEC1_ADDR { + address 0x0F4 + access_mode RW + size 2 + modes M_CFG + count 1 + dont_generate_debug_code +} + +/* + * Current Address + * Address of the SEQRAM instruction currently executing instruction. + */ +register CURADDR { + address 0x0F4 + access_mode RW + size 2 + modes M_SCSI + count 2 + dont_generate_debug_code +} + +/* + * Interrupt Vector 2 Address + * Interrupt branch address for HST_SEQ_INT2 interrupts. + */ +register INTVEC2_ADDR { + address 0x0F6 + access_mode RW + size 2 + modes M_CFG + count 1 + dont_generate_debug_code +} + +/* + * Last Address + * Address of the SEQRAM instruction executed prior to the current instruction. + */ +register LASTADDR { + address 0x0F6 + access_mode RW + size 2 + modes M_SCSI +} + +register AHD_PCI_CONFIG_BASE { + address 0x100 + access_mode RW + size 256 + modes M_CFG +} + +/* ---------------------- Scratch RAM Offsets ------------------------- */ +scratch_ram { + /* Mode Specific */ + address 0x0A0 + size 8 + modes 0, 1, 2, 3 + REG0 { + size 2 + dont_generate_debug_code + } + REG1 { + size 2 + } + REG_ISR { + size 2 + dont_generate_debug_code + } + SG_STATE { + size 1 + field SEGS_AVAIL 0x01 + field LOADING_NEEDED 0x02 + field FETCH_INPROG 0x04 + } + /* + * Track whether the transfer byte count for + * the current data phase is odd. + */ + DATA_COUNT_ODD { + size 1 + } +} + +scratch_ram { + /* Mode Specific */ + address 0x0F8 + size 8 + modes 0, 1, 2, 3 + LONGJMP_ADDR { + size 2 + dont_generate_debug_code + } + ACCUM_SAVE { + size 1 + dont_generate_debug_code + } +} + + +scratch_ram { + address 0x100 + size 128 + modes 0, 1, 2, 3 + /* + * Per "other-id" execution queues. We use an array of + * tail pointers into lists of SCBs sorted by "other-id". + * The execution head pointer threads the head SCBs for + * each list. + */ + WAITING_SCB_TAILS { + size 32 + dont_generate_debug_code + } + WAITING_TID_HEAD { + size 2 + dont_generate_debug_code + } + WAITING_TID_TAIL { + size 2 + dont_generate_debug_code + } + /* + * SCBID of the next SCB in the new SCB queue. + */ + NEXT_QUEUED_SCB_ADDR { + size 4 + dont_generate_debug_code + } + /* + * head of list of SCBs that have + * completed but have not been + * put into the qoutfifo. + */ + COMPLETE_SCB_HEAD { + size 2 + dont_generate_debug_code + } + /* + * The list of completed SCBs in + * the active DMA. + */ + COMPLETE_SCB_DMAINPROG_HEAD { + size 2 + dont_generate_debug_code + } + /* + * head of list of SCBs that have + * completed but need to be uploaded + * to the host prior to being completed. + */ + COMPLETE_DMA_SCB_HEAD { + size 2 + dont_generate_debug_code + } + /* + * tail of list of SCBs that have + * completed but need to be uploaded + * to the host prior to being completed. + */ + COMPLETE_DMA_SCB_TAIL { + size 2 + dont_generate_debug_code + } + /* + * head of list of SCBs that have + * been uploaded to the host, but cannot + * be completed until the QFREEZE is in + * full effect (i.e. no selections pending). + */ + COMPLETE_ON_QFREEZE_HEAD { + size 2 + dont_generate_debug_code + } + /* + * Counting semaphore to prevent new select-outs + * The queue is frozen so long as the sequencer + * and kernel freeze counts differ. + */ + QFREEZE_COUNT { + size 2 + } + KERNEL_QFREEZE_COUNT { + size 2 + } + /* + * Mode to restore on legacy idle loop exit. + */ + SAVED_MODE { + size 1 + } + /* + * Single byte buffer used to designate the type or message + * to send to a target. + */ + MSG_OUT { + size 1 + dont_generate_debug_code + } + /* Parameters for DMA Logic */ + DMAPARAMS { + size 1 + count 8 + field PRELOADEN 0x80 + field WIDEODD 0x40 + field SCSIEN 0x20 + field SDMAEN 0x10 + field SDMAENACK 0x10 + field HDMAEN 0x08 + field HDMAENACK 0x08 + field DIRECTION 0x04 /* Set indicates PCI->SCSI */ + field FIFOFLUSH 0x02 + field FIFORESET 0x01 + dont_generate_debug_code + } + SEQ_FLAGS { + size 1 + field NOT_IDENTIFIED 0x80 + field NO_CDB_SENT 0x40 + field TARGET_CMD_IS_TAGGED 0x40 + field DPHASE 0x20 + /* Target flags */ + field TARG_CMD_PENDING 0x10 + field CMDPHASE_PENDING 0x08 + field DPHASE_PENDING 0x04 + field SPHASE_PENDING 0x02 + field NO_DISCONNECT 0x01 + } + /* + * Temporary storage for the + * target/channel/lun of a + * reconnecting target + */ + SAVED_SCSIID { + size 1 + dont_generate_debug_code + } + SAVED_LUN { + size 1 + dont_generate_debug_code + } + /* + * The last bus phase as seen by the sequencer. + */ + LASTPHASE { + size 1 + field CDI 0x80 + field IOI 0x40 + field MSGI 0x20 + field P_BUSFREE 0x01 + enum PHASE_MASK CDO|IOO|MSGO { + P_DATAOUT 0x0, + P_DATAIN IOO, + P_DATAOUT_DT P_DATAOUT|MSGO, + P_DATAIN_DT P_DATAIN|MSGO, + P_COMMAND CDO, + P_MESGOUT CDO|MSGO, + P_STATUS CDO|IOO, + P_MESGIN CDO|IOO|MSGO + } + } + /* + * Value to "or" into the SCBPTR[1] value to + * indicate that an entry in the QINFIFO is valid. + */ + QOUTFIFO_ENTRY_VALID_TAG { + size 1 + dont_generate_debug_code + } + /* + * Kernel and sequencer offsets into the queue of + * incoming target mode command descriptors. The + * queue is full when the KERNEL_TQINPOS == TQINPOS. + */ + KERNEL_TQINPOS { + size 1 + count 1 + dont_generate_debug_code + } + TQINPOS { + size 1 + count 8 + dont_generate_debug_code + } + /* + * Base address of our shared data with the kernel driver in host + * memory. This includes the qoutfifo and target mode + * incoming command queue. + */ + SHARED_DATA_ADDR { + size 4 + dont_generate_debug_code + } + /* + * Pointer to location in host memory for next + * position in the qoutfifo. + */ + QOUTFIFO_NEXT_ADDR { + size 4 + dont_generate_debug_code + } + ARG_1 { + size 1 + mask SEND_MSG 0x80 + mask SEND_SENSE 0x40 + mask SEND_REJ 0x20 + mask MSGOUT_PHASEMIS 0x10 + mask EXIT_MSG_LOOP 0x08 + mask CONT_MSG_LOOP_WRITE 0x04 + mask CONT_MSG_LOOP_READ 0x03 + mask CONT_MSG_LOOP_TARG 0x02 + alias RETURN_1 + dont_generate_debug_code + } + ARG_2 { + size 1 + count 1 + alias RETURN_2 + dont_generate_debug_code + } + + /* + * Snapshot of MSG_OUT taken after each message is sent. + */ + LAST_MSG { + size 1 + dont_generate_debug_code + } + + /* + * Sequences the kernel driver has okayed for us. This allows + * the driver to do things like prevent initiator or target + * operations. + */ + SCSISEQ_TEMPLATE { + size 1 + count 7 + field MANUALCTL 0x40 + field ENSELI 0x20 + field ENRSELI 0x10 + field MANUALP 0x0C + field ENAUTOATNP 0x02 + field ALTSTIM 0x01 + dont_generate_debug_code + } + + /* + * The initiator specified tag for this target mode transaction. + */ + INITIATOR_TAG { + size 1 + count 1 + dont_generate_debug_code + } + + SEQ_FLAGS2 { + size 1 + field PENDING_MK_MESSAGE 0x01 + field TARGET_MSG_PENDING 0x02 + field SELECTOUT_QFROZEN 0x04 + } + + ALLOCFIFO_SCBPTR { + size 2 + dont_generate_debug_code + } + + /* + * The maximum amount of time to wait, when interrupt coalescing + * is enabled, before issuing a CMDCMPLT interrupt for a completed + * command. + */ + INT_COALESCING_TIMER { + size 2 + dont_generate_debug_code + } + + /* + * The maximum number of commands to coalesce into a single interrupt. + * Actually the 2's complement of that value to simplify sequencer + * code. + */ + INT_COALESCING_MAXCMDS { + size 1 + dont_generate_debug_code + } + + /* + * The minimum number of commands still outstanding required + * to continue coalescing (2's complement of value). + */ + INT_COALESCING_MINCMDS { + size 1 + dont_generate_debug_code + } + + /* + * Number of commands "in-flight". + */ + CMDS_PENDING { + size 2 + dont_generate_debug_code + } + + /* + * The count of commands that have been coalesced. + */ + INT_COALESCING_CMDCOUNT { + size 1 + dont_generate_debug_code + } + + /* + * Since the HS_MAIBOX is self clearing, copy its contents to + * this position in scratch ram every time it changes. + */ + LOCAL_HS_MAILBOX { + size 1 + dont_generate_debug_code + } + /* + * Target-mode CDB type to CDB length table used + * in non-packetized operation. + */ + CMDSIZE_TABLE { + size 8 + count 8 + dont_generate_debug_code + } + /* + * When an SCB with the MK_MESSAGE flag is + * queued to the controller, it cannot enter + * the waiting for selection list until the + * selections for any previously queued + * commands to that target complete. During + * the wait, the MK_MESSAGE SCB is queued + * here. + */ + MK_MESSAGE_SCB { + size 2 + } + /* + * Saved SCSIID of MK_MESSAGE_SCB to avoid + * an extra SCBPTR operation when deciding + * if the MK_MESSAGE_SCB can be run. + */ + MK_MESSAGE_SCSIID { + size 1 + } +} + +/************************* Hardware SCB Definition ****************************/ +scb { + address 0x180 + size 64 + modes 0, 1, 2, 3 + SCB_RESIDUAL_DATACNT { + size 4 + alias SCB_CDB_STORE + alias SCB_HOST_CDB_PTR + dont_generate_debug_code + } + SCB_RESIDUAL_SGPTR { + size 4 + field SG_ADDR_MASK 0xf8 /* In the last byte */ + field SG_OVERRUN_RESID 0x02 /* In the first byte */ + field SG_LIST_NULL 0x01 /* In the first byte */ + dont_generate_debug_code + } + SCB_SCSI_STATUS { + size 1 + alias SCB_HOST_CDB_LEN + dont_generate_debug_code + } + SCB_TARGET_PHASES { + size 1 + dont_generate_debug_code + } + SCB_TARGET_DATA_DIR { + size 1 + dont_generate_debug_code + } + SCB_TARGET_ITAG { + size 1 + dont_generate_debug_code + } + SCB_SENSE_BUSADDR { + /* + * Only valid if CDB length is less than 13 bytes or + * we are using a CDB pointer. Otherwise contains + * the last 4 bytes of embedded cdb information. + */ + size 4 + alias SCB_NEXT_COMPLETE + dont_generate_debug_code + } + SCB_TAG { + alias SCB_FIFO_USE_COUNT + size 2 + dont_generate_debug_code + } + SCB_CONTROL { + size 1 + field TARGET_SCB 0x80 + field DISCENB 0x40 + field TAG_ENB 0x20 + field MK_MESSAGE 0x10 + field STATUS_RCVD 0x08 + field DISCONNECTED 0x04 + field SCB_TAG_TYPE 0x03 + } + SCB_SCSIID { + size 1 + field TID 0xF0 + field OID 0x0F + } + SCB_LUN { + size 1 + field LID 0xff + dont_generate_debug_code + } + SCB_TASK_ATTRIBUTE { + size 1 + /* + * Overloaded field for non-packetized + * ignore wide residue message handling. + */ + field SCB_XFERLEN_ODD 0x01 + dont_generate_debug_code + } + SCB_CDB_LEN { + size 1 + field SCB_CDB_LEN_PTR 0x80 /* CDB in host memory */ + dont_generate_debug_code + } + SCB_TASK_MANAGEMENT { + size 1 + dont_generate_debug_code + } + SCB_DATAPTR { + size 8 + dont_generate_debug_code + } + SCB_DATACNT { + /* + * The last byte is really the high address bits for + * the data address. + */ + size 4 + field SG_LAST_SEG 0x80 /* In the fourth byte */ + field SG_HIGH_ADDR_BITS 0x7F /* In the fourth byte */ + dont_generate_debug_code + } + SCB_SGPTR { + size 4 + field SG_STATUS_VALID 0x04 /* In the first byte */ + field SG_FULL_RESID 0x02 /* In the first byte */ + field SG_LIST_NULL 0x01 /* In the first byte */ + dont_generate_debug_code + } + SCB_BUSADDR { + size 4 + dont_generate_debug_code + } + SCB_NEXT { + alias SCB_NEXT_SCB_BUSADDR + size 2 + dont_generate_debug_code + } + SCB_NEXT2 { + size 2 + dont_generate_debug_code + } + SCB_SPARE { + size 8 + alias SCB_PKT_LUN + } + SCB_DISCONNECTED_LISTS { + size 8 + dont_generate_debug_code + } +} + +/*********************************** Constants ********************************/ +const MK_MESSAGE_BIT_OFFSET 4 +const TID_SHIFT 4 +const TARGET_CMD_CMPLT 0xfe +const INVALID_ADDR 0x80 +#define SCB_LIST_NULL 0xff +#define QOUTFIFO_ENTRY_VALID_TOGGLE 0x80 + +const CCSGADDR_MAX 0x80 +const CCSCBADDR_MAX 0x80 +const CCSGRAM_MAXSEGS 16 + +/* Selection Timeout Timer Constants */ +const STIMESEL_SHIFT 3 +const STIMESEL_MIN 0x18 +const STIMESEL_BUG_ADJ 0x8 + +/* WDTR Message values */ +const BUS_8_BIT 0x00 +const BUS_16_BIT 0x01 +const BUS_32_BIT 0x02 + +/* Offset maximums */ +const MAX_OFFSET 0xfe +const MAX_OFFSET_PACED 0xfe +const MAX_OFFSET_PACED_BUG 0x7f +/* + * Some 160 devices incorrectly accept 0xfe as a + * sync offset, but will overrun this value. Limit + * to 0x7f for speed lower than U320 which will + * avoid the persistent sync offset overruns. + */ +const MAX_OFFSET_NON_PACED 0x7f +const HOST_MSG 0xff + +/* + * The size of our sense buffers. + * Sense buffer mapping can be handled in either of two ways. + * The first is to allocate a dmamap for each transaction. + * Depending on the architecture, dmamaps can be costly. The + * alternative is to statically map the buffers in much the same + * way we handle our scatter gather lists. The driver implements + * the later. + */ +const AHD_SENSE_BUFSIZE 256 + +/* Target mode command processing constants */ +const CMD_GROUP_CODE_SHIFT 0x05 + +const STATUS_BUSY 0x08 +const STATUS_QUEUE_FULL 0x28 +const STATUS_PKT_SENSE 0xFF +const TARGET_DATA_IN 1 + +const SCB_TRANSFER_SIZE_FULL_LUN 56 +const SCB_TRANSFER_SIZE_1BYTE_LUN 48 +/* PKT_OVERRUN_BUFSIZE must be a multiple of 256 less than 64K */ +const PKT_OVERRUN_BUFSIZE 512 + +/* + * Timer parameters. + */ +const AHD_TIMER_US_PER_TICK 25 +const AHD_TIMER_MAX_TICKS 0xFFFF +const AHD_TIMER_MAX_US (AHD_TIMER_MAX_TICKS * AHD_TIMER_US_PER_TICK) + +/* + * Downloaded (kernel inserted) constants + */ +const SG_PREFETCH_CNT download +const SG_PREFETCH_CNT_LIMIT download +const SG_PREFETCH_ALIGN_MASK download +const SG_PREFETCH_ADDR_MASK download +const SG_SIZEOF download +const PKT_OVERRUN_BUFOFFSET download +const SCB_TRANSFER_SIZE download +const CACHELINE_MASK download + +/* + * BIOS SCB offsets + */ +const NVRAM_SCB_OFFSET 0x2C diff --git a/drivers/scsi/aic7xxx/aic79xx.seq b/drivers/scsi/aic7xxx/aic79xx.seq new file mode 100644 index 000000000..3a36d9362 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx.seq @@ -0,0 +1,2290 @@ +/* + * Adaptec U320 device driver firmware for Linux and FreeBSD. + * + * Copyright (c) 1994-2001, 2004 Justin T. Gibbs. + * Copyright (c) 2000-2002 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $FreeBSD$ + */ + +VERSION = "$Id: //depot/aic7xxx/aic7xxx/aic79xx.seq#120 $" +PATCH_ARG_LIST = "struct ahd_softc *ahd" +PREFIX = "ahd_" + +#include "aic79xx.reg" +#include "scsi_message.h" + +restart: +if ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0) { + test SEQINTCODE, 0xFF jz idle_loop; + SET_SEQINTCODE(NO_SEQINT) +} + +idle_loop: + + if ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0) { + /* + * Convert ERROR status into a sequencer + * interrupt to handle the case of an + * interrupt collision on the hardware + * setting of HWERR. + */ + test ERROR, 0xFF jz no_error_set; + SET_SEQINTCODE(SAW_HWERR) +no_error_set: + } + SET_MODE(M_SCSI, M_SCSI) + test SCSISEQ0, ENSELO|ENARBO jnz idle_loop_checkbus; + test SEQ_FLAGS2, SELECTOUT_QFROZEN jz check_waiting_list; + /* + * If the kernel has caught up with us, thaw the queue. + */ + mov A, KERNEL_QFREEZE_COUNT; + cmp QFREEZE_COUNT, A jne check_frozen_completions; + mov A, KERNEL_QFREEZE_COUNT[1]; + cmp QFREEZE_COUNT[1], A jne check_frozen_completions; + and SEQ_FLAGS2, ~SELECTOUT_QFROZEN; + jmp check_waiting_list; +check_frozen_completions: + test SSTAT0, SELDO|SELINGO jnz idle_loop_checkbus; +BEGIN_CRITICAL; + /* + * If we have completions stalled waiting for the qfreeze + * to take effect, move them over to the complete_scb list + * now that no selections are pending. + */ + cmp COMPLETE_ON_QFREEZE_HEAD[1],SCB_LIST_NULL je idle_loop_checkbus; + /* + * Find the end of the qfreeze list. The first element has + * to be treated specially. + */ + bmov SCBPTR, COMPLETE_ON_QFREEZE_HEAD, 2; + cmp SCB_NEXT_COMPLETE[1], SCB_LIST_NULL je join_lists; + /* + * Now the normal loop. + */ + bmov SCBPTR, SCB_NEXT_COMPLETE, 2; + cmp SCB_NEXT_COMPLETE[1], SCB_LIST_NULL jne . - 1; +join_lists: + bmov SCB_NEXT_COMPLETE, COMPLETE_SCB_HEAD, 2; + bmov COMPLETE_SCB_HEAD, COMPLETE_ON_QFREEZE_HEAD, 2; + mvi COMPLETE_ON_QFREEZE_HEAD[1], SCB_LIST_NULL; + jmp idle_loop_checkbus; +check_waiting_list: + cmp WAITING_TID_HEAD[1], SCB_LIST_NULL je idle_loop_checkbus; + /* + * ENSELO is cleared by a SELDO, so we must test for SELDO + * one last time. + */ + test SSTAT0, SELDO jnz select_out; + call start_selection; +idle_loop_checkbus: + test SSTAT0, SELDO jnz select_out; +END_CRITICAL; + test SSTAT0, SELDI jnz select_in; + test SCSIPHASE, ~DATA_PHASE_MASK jz idle_loop_check_nonpackreq; + test SCSISIGO, ATNO jz idle_loop_check_nonpackreq; + call unexpected_nonpkt_phase_find_ctxt; +idle_loop_check_nonpackreq: + test SSTAT2, NONPACKREQ jz . + 2; + call unexpected_nonpkt_phase_find_ctxt; + if ((ahd->bugs & AHD_FAINT_LED_BUG) != 0) { + /* + * On Rev A. hardware, the busy LED is only + * turned on automaically during selections + * and re-selections. Make the LED status + * more useful by forcing it to be on so + * long as one of our data FIFOs is active. + */ + and A, FIFO0FREE|FIFO1FREE, DFFSTAT; + cmp A, FIFO0FREE|FIFO1FREE jne . + 3; + and SBLKCTL, ~DIAGLEDEN|DIAGLEDON; + jmp . + 2; + or SBLKCTL, DIAGLEDEN|DIAGLEDON; + } + call idle_loop_gsfifo_in_scsi_mode; + call idle_loop_service_fifos; + call idle_loop_cchan; + jmp idle_loop; + +idle_loop_gsfifo: + SET_MODE(M_SCSI, M_SCSI) +BEGIN_CRITICAL; +idle_loop_gsfifo_in_scsi_mode: + test LQISTAT2, LQIGSAVAIL jz return; + /* + * We have received good status for this transaction. There may + * still be data in our FIFOs draining to the host. Complete + * the SCB only if all data has transferred to the host. + */ +good_status_IU_done: + bmov SCBPTR, GSFIFO, 2; + clr SCB_SCSI_STATUS; + /* + * If a command completed before an attempted task management + * function completed, notify the host after disabling any + * pending select-outs. + */ + test SCB_TASK_MANAGEMENT, 0xFF jz gsfifo_complete_normally; + test SSTAT0, SELDO|SELINGO jnz . + 2; + and SCSISEQ0, ~ENSELO; + SET_SEQINTCODE(TASKMGMT_CMD_CMPLT_OKAY) +gsfifo_complete_normally: + or SCB_CONTROL, STATUS_RCVD; + + /* + * Since this status did not consume a FIFO, we have to + * be a bit more dilligent in how we check for FIFOs pertaining + * to this transaction. There are two states that a FIFO still + * transferring data may be in. + * + * 1) Configured and draining to the host, with a FIFO handler. + * 2) Pending cfg4data, fifo not empty. + * + * Case 1 can be detected by noticing a non-zero FIFO active + * count in the SCB. In this case, we allow the routine servicing + * the FIFO to complete the SCB. + * + * Case 2 implies either a pending or yet to occur save data + * pointers for this same context in the other FIFO. So, if + * we detect case 1, we will properly defer the post of the SCB + * and achieve the desired result. The pending cfg4data will + * notice that status has been received and complete the SCB. + */ + test SCB_FIFO_USE_COUNT, 0xFF jnz idle_loop_gsfifo_in_scsi_mode; + call complete; +END_CRITICAL; + jmp idle_loop_gsfifo_in_scsi_mode; + +idle_loop_service_fifos: + SET_MODE(M_DFF0, M_DFF0) +BEGIN_CRITICAL; + test LONGJMP_ADDR[1], INVALID_ADDR jnz idle_loop_next_fifo; + call longjmp; +END_CRITICAL; +idle_loop_next_fifo: + SET_MODE(M_DFF1, M_DFF1) +BEGIN_CRITICAL; + test LONGJMP_ADDR[1], INVALID_ADDR jz longjmp; +END_CRITICAL; +return: + ret; + +idle_loop_cchan: + SET_MODE(M_CCHAN, M_CCHAN) + test QOFF_CTLSTA, HS_MAILBOX_ACT jz hs_mailbox_empty; + or QOFF_CTLSTA, HS_MAILBOX_ACT; + mov LOCAL_HS_MAILBOX, HS_MAILBOX; +hs_mailbox_empty: +BEGIN_CRITICAL; + test CCSCBCTL, CCARREN|CCSCBEN jz scbdma_idle; + test CCSCBCTL, CCSCBDIR jnz fetch_new_scb_inprog; + test CCSCBCTL, CCSCBDONE jz return; + /* FALLTHROUGH */ +scbdma_tohost_done: + test CCSCBCTL, CCARREN jz fill_qoutfifo_dmadone; + /* + * An SCB has been successfully uploaded to the host. + * If the SCB was uploaded for some reason other than + * bad SCSI status (currently only for underruns), we + * queue the SCB for normal completion. Otherwise, we + * wait until any select-out activity has halted, and + * then queue the completion. + */ + and CCSCBCTL, ~(CCARREN|CCSCBEN); + bmov COMPLETE_DMA_SCB_HEAD, SCB_NEXT_COMPLETE, 2; + cmp SCB_NEXT_COMPLETE[1], SCB_LIST_NULL jne . + 2; + mvi COMPLETE_DMA_SCB_TAIL[1], SCB_LIST_NULL; + test SCB_SCSI_STATUS, 0xff jz scbdma_queue_completion; + bmov SCB_NEXT_COMPLETE, COMPLETE_ON_QFREEZE_HEAD, 2; + bmov COMPLETE_ON_QFREEZE_HEAD, SCBPTR, 2 ret; +scbdma_queue_completion: + bmov SCB_NEXT_COMPLETE, COMPLETE_SCB_HEAD, 2; + bmov COMPLETE_SCB_HEAD, SCBPTR, 2 ret; +fill_qoutfifo_dmadone: + and CCSCBCTL, ~(CCARREN|CCSCBEN); + call qoutfifo_updated; + mvi COMPLETE_SCB_DMAINPROG_HEAD[1], SCB_LIST_NULL; + bmov QOUTFIFO_NEXT_ADDR, SCBHADDR, 4; + test QOFF_CTLSTA, SDSCB_ROLLOVR jz return; + bmov QOUTFIFO_NEXT_ADDR, SHARED_DATA_ADDR, 4; + xor QOUTFIFO_ENTRY_VALID_TAG, QOUTFIFO_ENTRY_VALID_TOGGLE ret; +END_CRITICAL; + +qoutfifo_updated: + /* + * If there are more commands waiting to be dma'ed + * to the host, always coalesce. Otherwise honor the + * host's wishes. + */ + cmp COMPLETE_DMA_SCB_HEAD[1], SCB_LIST_NULL jne coalesce_by_count; + cmp COMPLETE_SCB_HEAD[1], SCB_LIST_NULL jne coalesce_by_count; + test LOCAL_HS_MAILBOX, ENINT_COALESCE jz issue_cmdcmplt; + + /* + * If we have relatively few commands outstanding, don't + * bother waiting for another command to complete. + */ + test CMDS_PENDING[1], 0xFF jnz coalesce_by_count; + /* Add -1 so that jnc means <= not just < */ + add A, -1, INT_COALESCING_MINCMDS; + add NONE, A, CMDS_PENDING; + jnc issue_cmdcmplt; + + /* + * If coalescing, only coalesce up to the limit + * provided by the host driver. + */ +coalesce_by_count: + mov A, INT_COALESCING_MAXCMDS; + add NONE, A, INT_COALESCING_CMDCOUNT; + jc issue_cmdcmplt; + /* + * If the timer is not currently active, + * fire it up. + */ + test INTCTL, SWTMINTMASK jz return; + bmov SWTIMER, INT_COALESCING_TIMER, 2; + mvi CLRSEQINTSTAT, CLRSEQ_SWTMRTO; + or INTCTL, SWTMINTEN|SWTIMER_START; + and INTCTL, ~SWTMINTMASK ret; + +issue_cmdcmplt: + mvi INTSTAT, CMDCMPLT; + clr INT_COALESCING_CMDCOUNT; + or INTCTL, SWTMINTMASK ret; + +BEGIN_CRITICAL; +fetch_new_scb_inprog: + test CCSCBCTL, ARRDONE jz return; +fetch_new_scb_done: + and CCSCBCTL, ~(CCARREN|CCSCBEN); + clr A; + add CMDS_PENDING, 1; + adc CMDS_PENDING[1], A; + if ((ahd->bugs & AHD_PKT_LUN_BUG) != 0) { + /* + * "Short Luns" are not placed into outgoing LQ + * packets in the correct byte order. Use a full + * sized lun field instead and fill it with the + * one byte of lun information we support. + */ + mov SCB_PKT_LUN[6], SCB_LUN; + } + /* + * The FIFO use count field is shared with the + * tag set by the host so that our SCB dma engine + * knows the correct location to store the SCB. + * Set it to zero before processing the SCB. + */ + clr SCB_FIFO_USE_COUNT; + /* Update the next SCB address to download. */ + bmov NEXT_QUEUED_SCB_ADDR, SCB_NEXT_SCB_BUSADDR, 4; + /* + * NULL out the SCB links since these fields + * occupy the same location as SCB_NEXT_SCB_BUSADDR. + */ + mvi SCB_NEXT[1], SCB_LIST_NULL; + mvi SCB_NEXT2[1], SCB_LIST_NULL; + /* Increment our position in the QINFIFO. */ + mov NONE, SNSCB_QOFF; + + /* + * Save SCBID of this SCB in REG0 since + * SCBPTR will be clobbered during target + * list updates. We also record the SCB's + * flags so that we can refer to them even + * after SCBPTR has been changed. + */ + bmov REG0, SCBPTR, 2; + mov A, SCB_CONTROL; + + /* + * Find the tail SCB of the execution queue + * for this target. + */ + shr SINDEX, 3, SCB_SCSIID; + and SINDEX, ~0x1; + mvi SINDEX[1], (WAITING_SCB_TAILS >> 8); + bmov DINDEX, SINDEX, 2; + bmov SCBPTR, SINDIR, 2; + + /* + * Update the tail to point to the new SCB. + */ + bmov DINDIR, REG0, 2; + + /* + * If the queue was empty, queue this SCB as + * the first for this target. + */ + cmp SCBPTR[1], SCB_LIST_NULL je first_new_target_scb; + + /* + * SCBs that want to send messages must always be + * at the head of their per-target queue so that + * ATN can be asserted even if the current + * negotiation agreement is packetized. If the + * target queue is empty, the SCB can be queued + * immediately. If the queue is not empty, we must + * wait for it to empty before entering this SCB + * into the waiting for selection queue. Otherwise + * our batching and round-robin selection scheme + * could allow commands to be queued out of order. + * To simplify the implementation, we stop pulling + * new commands from the host until the MK_MESSAGE + * SCB can be queued to the waiting for selection + * list. + */ + test A, MK_MESSAGE jz batch_scb; + + /* + * If the last SCB is also a MK_MESSAGE SCB, then + * order is preserved even if we batch. + */ + test SCB_CONTROL, MK_MESSAGE jz batch_scb; + + /* + * Defer this SCB and stop fetching new SCBs until + * it can be queued. Since the SCB_SCSIID of the + * tail SCB must be the same as that of the newly + * queued SCB, there is no need to restore the SCBID + * here. + */ + or SEQ_FLAGS2, PENDING_MK_MESSAGE; + bmov MK_MESSAGE_SCB, REG0, 2; + mov MK_MESSAGE_SCSIID, SCB_SCSIID ret; + +batch_scb: + /* + * Otherwise just update the previous tail SCB to + * point to the new tail. + */ + bmov SCB_NEXT, REG0, 2 ret; + +first_new_target_scb: + /* + * Append SCB to the tail of the waiting for + * selection list. + */ + cmp WAITING_TID_HEAD[1], SCB_LIST_NULL je first_new_scb; + bmov SCBPTR, WAITING_TID_TAIL, 2; + bmov SCB_NEXT2, REG0, 2; + bmov WAITING_TID_TAIL, REG0, 2 ret; +first_new_scb: + /* + * Whole list is empty, so the head of + * the list must be initialized too. + */ + bmov WAITING_TID_HEAD, REG0, 2; + bmov WAITING_TID_TAIL, REG0, 2 ret; +END_CRITICAL; + +scbdma_idle: + /* + * Don't bother downloading new SCBs to execute + * if select-outs are currently frozen or we have + * a MK_MESSAGE SCB waiting to enter the queue. + */ + test SEQ_FLAGS2, SELECTOUT_QFROZEN|PENDING_MK_MESSAGE + jnz scbdma_no_new_scbs; +BEGIN_CRITICAL; + test QOFF_CTLSTA, NEW_SCB_AVAIL jnz fetch_new_scb; +scbdma_no_new_scbs: + cmp COMPLETE_DMA_SCB_HEAD[1], SCB_LIST_NULL jne dma_complete_scb; + cmp COMPLETE_SCB_HEAD[1], SCB_LIST_NULL je return; + /* FALLTHROUGH */ +fill_qoutfifo: + /* + * Keep track of the SCBs we are dmaing just + * in case the DMA fails or is aborted. + */ + bmov COMPLETE_SCB_DMAINPROG_HEAD, COMPLETE_SCB_HEAD, 2; + mvi CCSCBCTL, CCSCBRESET; + bmov SCBHADDR, QOUTFIFO_NEXT_ADDR, 4; + mov A, QOUTFIFO_NEXT_ADDR; + bmov SCBPTR, COMPLETE_SCB_HEAD, 2; +fill_qoutfifo_loop: + bmov CCSCBRAM, SCBPTR, 2; + mov CCSCBRAM, SCB_SGPTR[0]; + mov CCSCBRAM, QOUTFIFO_ENTRY_VALID_TAG; + mov NONE, SDSCB_QOFF; + inc INT_COALESCING_CMDCOUNT; + add CMDS_PENDING, -1; + adc CMDS_PENDING[1], -1; + cmp SCB_NEXT_COMPLETE[1], SCB_LIST_NULL je fill_qoutfifo_done; + cmp CCSCBADDR, CCSCBADDR_MAX je fill_qoutfifo_done; + test QOFF_CTLSTA, SDSCB_ROLLOVR jnz fill_qoutfifo_done; + /* + * Don't cross an ADB or Cachline boundary when DMA'ing + * completion entries. In PCI mode, at least in 32/33 + * configurations, the SCB DMA engine may lose its place + * in the data-stream should the target force a retry on + * something other than an 8byte aligned boundary. In + * PCI-X mode, we do this to avoid split transactions since + * many chipsets seem to be unable to format proper split + * completions to continue the data transfer. + */ + add SINDEX, A, CCSCBADDR; + test SINDEX, CACHELINE_MASK jz fill_qoutfifo_done; + bmov SCBPTR, SCB_NEXT_COMPLETE, 2; + jmp fill_qoutfifo_loop; +fill_qoutfifo_done: + mov SCBHCNT, CCSCBADDR; + mvi CCSCBCTL, CCSCBEN|CCSCBRESET; + bmov COMPLETE_SCB_HEAD, SCB_NEXT_COMPLETE, 2; + mvi SCB_NEXT_COMPLETE[1], SCB_LIST_NULL ret; + +fetch_new_scb: + bmov SCBHADDR, NEXT_QUEUED_SCB_ADDR, 4; + mvi CCARREN|CCSCBEN|CCSCBDIR|CCSCBRESET jmp dma_scb; +dma_complete_scb: + bmov SCBPTR, COMPLETE_DMA_SCB_HEAD, 2; + bmov SCBHADDR, SCB_BUSADDR, 4; + mvi CCARREN|CCSCBEN|CCSCBRESET jmp dma_scb; + +/* + * Either post or fetch an SCB from host memory. The caller + * is responsible for polling for transfer completion. + * + * Prerequisits: Mode == M_CCHAN + * SINDEX contains CCSCBCTL flags + * SCBHADDR set to Host SCB address + * SCBPTR set to SCB src location on "push" operations + */ +SET_SRC_MODE M_CCHAN; +SET_DST_MODE M_CCHAN; +dma_scb: + mvi SCBHCNT, SCB_TRANSFER_SIZE; + mov CCSCBCTL, SINDEX ret; + +setjmp: + /* + * At least on the A, a return in the same + * instruction as the bmov results in a return + * to the caller, not to the new address at the + * top of the stack. Since we want the latter + * (we use setjmp to register a handler from an + * interrupt context but not invoke that handler + * until we return to our idle loop), use a + * separate ret instruction. + */ + bmov LONGJMP_ADDR, STACK, 2; + ret; +setjmp_inline: + bmov LONGJMP_ADDR, STACK, 2; +longjmp: + bmov STACK, LONGJMP_ADDR, 2 ret; +END_CRITICAL; + +/*************************** Chip Bug Work Arounds ****************************/ +/* + * Must disable interrupts when setting the mode pointer + * register as an interrupt occurring mid update will + * fail to store the new mode value for restoration on + * an iret. + */ +if ((ahd->bugs & AHD_SET_MODE_BUG) != 0) { +set_mode_work_around: + mvi SEQINTCTL, INTVEC1DSL; + mov MODE_PTR, SINDEX; + clr SEQINTCTL ret; +} + + +if ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0) { +set_seqint_work_around: + mov SEQINTCODE, SINDEX; + mvi SEQINTCODE, NO_SEQINT ret; +} + +/************************ Packetized LongJmp Routines *************************/ +SET_SRC_MODE M_SCSI; +SET_DST_MODE M_SCSI; +start_selection: +BEGIN_CRITICAL; + if ((ahd->bugs & AHD_SENT_SCB_UPDATE_BUG) != 0) { + /* + * Razor #494 + * Rev A hardware fails to update LAST/CURR/NEXTSCB + * correctly after a packetized selection in several + * situations: + * + * 1) If only one command existed in the queue, the + * LAST/CURR/NEXTSCB are unchanged. + * + * 2) In a non QAS, protocol allowed phase change, + * the queue is shifted 1 too far. LASTSCB is + * the last SCB that was correctly processed. + * + * 3) In the QAS case, if the full list of commands + * was successfully sent, NEXTSCB is NULL and neither + * CURRSCB nor LASTSCB can be trusted. We must + * manually walk the list counting MAXCMDCNT elements + * to find the last SCB that was sent correctly. + * + * To simplify the workaround for this bug in SELDO + * handling, we initialize LASTSCB prior to enabling + * selection so we can rely on it even for case #1 above. + */ + bmov LASTSCB, WAITING_TID_HEAD, 2; + } + bmov CURRSCB, WAITING_TID_HEAD, 2; + bmov SCBPTR, WAITING_TID_HEAD, 2; + shr SELOID, 4, SCB_SCSIID; + /* + * If we want to send a message to the device, ensure + * we are selecting with atn regardless of our packetized + * agreement. Since SPI4 only allows target reset or PPR + * messages if this is a packetized connection, the change + * to our negotiation table entry for this selection will + * be cleared when the message is acted on. + */ + test SCB_CONTROL, MK_MESSAGE jz . + 3; + mov NEGOADDR, SELOID; + or NEGCONOPTS, ENAUTOATNO; + or SCSISEQ0, ENSELO ret; +END_CRITICAL; + +/* + * Allocate a FIFO for a non-packetized transaction. + * In RevA hardware, both FIFOs must be free before we + * can allocate a FIFO for a non-packetized transaction. + */ +allocate_fifo_loop: + /* + * Do whatever work is required to free a FIFO. + */ + call idle_loop_service_fifos; + SET_MODE(M_SCSI, M_SCSI) +allocate_fifo: + if ((ahd->bugs & AHD_NONPACKFIFO_BUG) != 0) { + and A, FIFO0FREE|FIFO1FREE, DFFSTAT; + cmp A, FIFO0FREE|FIFO1FREE jne allocate_fifo_loop; + } else { + test DFFSTAT, FIFO1FREE jnz allocate_fifo1; + test DFFSTAT, FIFO0FREE jz allocate_fifo_loop; + mvi DFFSTAT, B_CURRFIFO_0; + SET_MODE(M_DFF0, M_DFF0) + bmov SCBPTR, ALLOCFIFO_SCBPTR, 2 ret; + } +SET_SRC_MODE M_SCSI; +SET_DST_MODE M_SCSI; +allocate_fifo1: + mvi DFFSTAT, CURRFIFO_1; + SET_MODE(M_DFF1, M_DFF1) + bmov SCBPTR, ALLOCFIFO_SCBPTR, 2 ret; + +/* + * We have been reselected as an initiator + * or selected as a target. + */ +SET_SRC_MODE M_SCSI; +SET_DST_MODE M_SCSI; +select_in: + if ((ahd->bugs & AHD_FAINT_LED_BUG) != 0) { + /* + * On Rev A. hardware, the busy LED is only + * turned on automaically during selections + * and re-selections. Make the LED status + * more useful by forcing it to be on from + * the point of selection until our idle + * loop determines that neither of our FIFOs + * are busy. This handles the non-packetized + * case nicely as we will not return to the + * idle loop until the busfree at the end of + * each transaction. + */ + or SBLKCTL, DIAGLEDEN|DIAGLEDON; + } + if ((ahd->bugs & AHD_BUSFREEREV_BUG) != 0) { + /* + * Test to ensure that the bus has not + * already gone free prior to clearing + * any stale busfree status. This avoids + * a window whereby a busfree just after + * a selection could be missed. + */ + test SCSISIGI, BSYI jz . + 2; + mvi CLRSINT1,CLRBUSFREE; + or SIMODE1, ENBUSFREE; + } + or SXFRCTL0, SPIOEN; + and SAVED_SCSIID, SELID_MASK, SELID; + and A, OID, IOWNID; + or SAVED_SCSIID, A; + mvi CLRSINT0, CLRSELDI; + jmp ITloop; + +/* + * We have successfully selected out. + * + * Clear SELDO. + * Dequeue all SCBs sent from the waiting queue + * Requeue all SCBs *not* sent to the tail of the waiting queue + * Take Razor #494 into account for above. + * + * In Packetized Mode: + * Return to the idle loop. Our interrupt handler will take + * care of any incoming L_Qs. + * + * In Non-Packetize Mode: + * Continue to our normal state machine. + */ +SET_SRC_MODE M_SCSI; +SET_DST_MODE M_SCSI; +select_out: +BEGIN_CRITICAL; + if ((ahd->bugs & AHD_FAINT_LED_BUG) != 0) { + /* + * On Rev A. hardware, the busy LED is only + * turned on automaically during selections + * and re-selections. Make the LED status + * more useful by forcing it to be on from + * the point of re-selection until our idle + * loop determines that neither of our FIFOs + * are busy. This handles the non-packetized + * case nicely as we will not return to the + * idle loop until the busfree at the end of + * each transaction. + */ + or SBLKCTL, DIAGLEDEN|DIAGLEDON; + } + /* Clear out all SCBs that have been successfully sent. */ + if ((ahd->bugs & AHD_SENT_SCB_UPDATE_BUG) != 0) { + /* + * For packetized, the LQO manager clears ENSELO on + * the assertion of SELDO. If we are non-packetized, + * LASTSCB and CURRSCB are accurate. + */ + test SCSISEQ0, ENSELO jnz use_lastscb; + + /* + * The update is correct for LQOSTAT1 errors. All + * but LQOBUSFREE are handled by kernel interrupts. + * If we see LQOBUSFREE, return to the idle loop. + * Once we are out of the select_out critical section, + * the kernel will cleanup the LQOBUSFREE and we will + * eventually restart the selection if appropriate. + */ + test LQOSTAT1, LQOBUSFREE jnz idle_loop; + + /* + * On a phase change oustside of packet boundaries, + * LASTSCB points to the currently active SCB context + * on the bus. + */ + test LQOSTAT2, LQOPHACHGOUTPKT jnz use_lastscb; + + /* + * If the hardware has traversed the whole list, NEXTSCB + * will be NULL, CURRSCB and LASTSCB cannot be trusted, + * but MAXCMDCNT is accurate. If we stop part way through + * the list or only had one command to issue, NEXTSCB[1] is + * not NULL and LASTSCB is the last command to go out. + */ + cmp NEXTSCB[1], SCB_LIST_NULL jne use_lastscb; + + /* + * Brute force walk. + */ + bmov SCBPTR, WAITING_TID_HEAD, 2; + mvi SEQINTCTL, INTVEC1DSL; + mvi MODE_PTR, MK_MODE(M_CFG, M_CFG); + mov A, MAXCMDCNT; + mvi MODE_PTR, MK_MODE(M_SCSI, M_SCSI); + clr SEQINTCTL; +find_lastscb_loop: + dec A; + test A, 0xFF jz found_last_sent_scb; + bmov SCBPTR, SCB_NEXT, 2; + jmp find_lastscb_loop; +use_lastscb: + bmov SCBPTR, LASTSCB, 2; +found_last_sent_scb: + bmov CURRSCB, SCBPTR, 2; +curscb_ww_done: + } else { + bmov SCBPTR, CURRSCB, 2; + } + + /* + * The whole list made it. Clear our tail pointer to indicate + * that the per-target selection queue is now empty. + */ + cmp SCB_NEXT[1], SCB_LIST_NULL je select_out_clear_tail; + + /* + * Requeue any SCBs not sent, to the tail of the waiting Q. + * We know that neither the per-TID list nor the list of + * TIDs is empty. Use this knowledge to our advantage and + * queue the remainder to the tail of the global execution + * queue. + */ + bmov REG0, SCB_NEXT, 2; +select_out_queue_remainder: + bmov SCBPTR, WAITING_TID_TAIL, 2; + bmov SCB_NEXT2, REG0, 2; + bmov WAITING_TID_TAIL, REG0, 2; + jmp select_out_inc_tid_q; + +select_out_clear_tail: + /* + * Queue any pending MK_MESSAGE SCB for this target now + * that the queue is empty. + */ + test SEQ_FLAGS2, PENDING_MK_MESSAGE jz select_out_no_mk_message_scb; + mov A, MK_MESSAGE_SCSIID; + cmp SCB_SCSIID, A jne select_out_no_mk_message_scb; + and SEQ_FLAGS2, ~PENDING_MK_MESSAGE; + bmov REG0, MK_MESSAGE_SCB, 2; + jmp select_out_queue_remainder; + +select_out_no_mk_message_scb: + /* + * Clear this target's execution tail and increment the queue. + */ + shr DINDEX, 3, SCB_SCSIID; + or DINDEX, 1; /* Want only the second byte */ + mvi DINDEX[1], ((WAITING_SCB_TAILS) >> 8); + mvi DINDIR, SCB_LIST_NULL; +select_out_inc_tid_q: + bmov SCBPTR, WAITING_TID_HEAD, 2; + bmov WAITING_TID_HEAD, SCB_NEXT2, 2; + cmp WAITING_TID_HEAD[1], SCB_LIST_NULL jne . + 2; + mvi WAITING_TID_TAIL[1], SCB_LIST_NULL; + bmov SCBPTR, CURRSCB, 2; + mvi CLRSINT0, CLRSELDO; + test LQOSTAT2, LQOPHACHGOUTPKT jnz unexpected_nonpkt_mode_cleared; + test LQOSTAT1, LQOPHACHGINPKT jnz unexpected_nonpkt_mode_cleared; + + /* + * If this is a packetized connection, return to our + * idle_loop and let our interrupt handler deal with + * any connection setup/teardown issues. The only + * exceptions are the case of MK_MESSAGE and task management + * SCBs. + */ + if ((ahd->bugs & AHD_LQO_ATNO_BUG) != 0) { + /* + * In the A, the LQO manager transitions to LQOSTOP0 even if + * we have selected out with ATN asserted and the target + * REQs in a non-packet phase. + */ + test SCB_CONTROL, MK_MESSAGE jz select_out_no_message; + test SCSISIGO, ATNO jnz select_out_non_packetized; +select_out_no_message: + } + test LQOSTAT2, LQOSTOP0 jz select_out_non_packetized; + test SCB_TASK_MANAGEMENT, 0xFF jz idle_loop; + SET_SEQINTCODE(TASKMGMT_FUNC_COMPLETE) + jmp idle_loop; + +select_out_non_packetized: + /* Non packetized request. */ + and SCSISEQ0, ~ENSELO; + if ((ahd->bugs & AHD_BUSFREEREV_BUG) != 0) { + /* + * Test to ensure that the bus has not + * already gone free prior to clearing + * any stale busfree status. This avoids + * a window whereby a busfree just after + * a selection could be missed. + */ + test SCSISIGI, BSYI jz . + 2; + mvi CLRSINT1,CLRBUSFREE; + or SIMODE1, ENBUSFREE; + } + mov SAVED_SCSIID, SCB_SCSIID; + mov SAVED_LUN, SCB_LUN; + mvi SEQ_FLAGS, NO_CDB_SENT; +END_CRITICAL; + or SXFRCTL0, SPIOEN; + + /* + * As soon as we get a successful selection, the target + * should go into the message out phase since we have ATN + * asserted. + */ + mvi MSG_OUT, MSG_IDENTIFYFLAG; + + /* + * Main loop for information transfer phases. Wait for the + * target to assert REQ before checking MSG, C/D and I/O for + * the bus phase. + */ +mesgin_phasemis: +ITloop: + call phase_lock; + + mov A, LASTPHASE; + + test A, ~P_DATAIN_DT jz p_data; + cmp A,P_COMMAND je p_command; + cmp A,P_MESGOUT je p_mesgout; + cmp A,P_STATUS je p_status; + cmp A,P_MESGIN je p_mesgin; + + SET_SEQINTCODE(BAD_PHASE) + jmp ITloop; /* Try reading the bus again. */ + +/* + * Command phase. Set up the DMA registers and let 'er rip. + */ +p_command: + test SEQ_FLAGS, NOT_IDENTIFIED jz p_command_okay; + SET_SEQINTCODE(PROTO_VIOLATION) +p_command_okay: + test MODE_PTR, ~(MK_MODE(M_DFF1, M_DFF1)) + jnz p_command_allocate_fifo; + /* + * Command retry. Free our current FIFO and + * re-allocate a FIFO so transfer state is + * reset. + */ +SET_SRC_MODE M_DFF1; +SET_DST_MODE M_DFF1; + mvi DFFSXFRCTL, RSTCHN|CLRSHCNT; + SET_MODE(M_SCSI, M_SCSI) +p_command_allocate_fifo: + bmov ALLOCFIFO_SCBPTR, SCBPTR, 2; + call allocate_fifo; +SET_SRC_MODE M_DFF1; +SET_DST_MODE M_DFF1; + add NONE, -17, SCB_CDB_LEN; + jnc p_command_embedded; +p_command_from_host: + bmov HADDR[0], SCB_HOST_CDB_PTR, 9; + mvi SG_CACHE_PRE, LAST_SEG; + mvi DFCNTRL, (PRELOADEN|SCSIEN|HDMAEN); + jmp p_command_xfer; +p_command_embedded: + bmov SHCNT[0], SCB_CDB_LEN, 1; + bmov DFDAT, SCB_CDB_STORE, 16; + mvi DFCNTRL, SCSIEN; +p_command_xfer: + and SEQ_FLAGS, ~NO_CDB_SENT; + if ((ahd->features & AHD_FAST_CDB_DELIVERY) != 0) { + /* + * To speed up CDB delivery in Rev B, all CDB acks + * are "released" to the output sync as soon as the + * command phase starts. There is only one problem + * with this approach. If the target changes phase + * before all data are sent, we have left over acks + * that can go out on the bus in a data phase. Due + * to other chip contraints, this only happens if + * the target goes to data-in, but if the acks go + * out before we can test SDONE, we'll think that + * the transfer has completed successfully. Work + * around this by taking advantage of the 400ns or + * 800ns dead time between command phase and the REQ + * of the new phase. If the transfer has completed + * successfully, SCSIEN should fall *long* before we + * see a phase change. We thus treat any phasemiss + * that occurs before SCSIEN falls as an incomplete + * transfer. + */ + test SSTAT1, PHASEMIS jnz p_command_xfer_failed; + test DFCNTRL, SCSIEN jnz . - 1; + } else { + test DFCNTRL, SCSIEN jnz .; + } + /* + * DMA Channel automatically disabled. + * Don't allow a data phase if the command + * was not fully transferred. + */ + test SSTAT2, SDONE jnz ITloop; +p_command_xfer_failed: + or SEQ_FLAGS, NO_CDB_SENT; + jmp ITloop; + + +/* + * Status phase. Wait for the data byte to appear, then read it + * and store it into the SCB. + */ +SET_SRC_MODE M_SCSI; +SET_DST_MODE M_SCSI; +p_status: + test SEQ_FLAGS,NOT_IDENTIFIED jnz mesgin_proto_violation; +p_status_okay: + mov SCB_SCSI_STATUS, SCSIDAT; + or SCB_CONTROL, STATUS_RCVD; + jmp ITloop; + +/* + * Message out phase. If MSG_OUT is MSG_IDENTIFYFLAG, build a full + * indentify message sequence and send it to the target. The host may + * override this behavior by setting the MK_MESSAGE bit in the SCB + * control byte. This will cause us to interrupt the host and allow + * it to handle the message phase completely on its own. If the bit + * associated with this target is set, we will also interrupt the host, + * thereby allowing it to send a message on the next selection regardless + * of the transaction being sent. + * + * If MSG_OUT is == HOST_MSG, also interrupt the host and take a message. + * This is done to allow the host to send messages outside of an identify + * sequence while protecting the seqencer from testing the MK_MESSAGE bit + * on an SCB that might not be for the current nexus. (For example, a + * BDR message in response to a bad reselection would leave us pointed to + * an SCB that doesn't have anything to do with the current target). + * + * Otherwise, treat MSG_OUT as a 1 byte message to send (abort, abort tag, + * bus device reset). + * + * When there are no messages to send, MSG_OUT should be set to MSG_NOOP, + * in case the target decides to put us in this phase for some strange + * reason. + */ +p_mesgout_retry: + /* Turn on ATN for the retry */ + mvi SCSISIGO, ATNO; +p_mesgout: + mov SINDEX, MSG_OUT; + cmp SINDEX, MSG_IDENTIFYFLAG jne p_mesgout_from_host; + test SCB_CONTROL,MK_MESSAGE jnz host_message_loop; +p_mesgout_identify: + or SINDEX, MSG_IDENTIFYFLAG|DISCENB, SCB_LUN; + test SCB_CONTROL, DISCENB jnz . + 2; + and SINDEX, ~DISCENB; +/* + * Send a tag message if TAG_ENB is set in the SCB control block. + * Use SCB_NONPACKET_TAG as the tag value. + */ +p_mesgout_tag: + test SCB_CONTROL,TAG_ENB jz p_mesgout_onebyte; + mov SCSIDAT, SINDEX; /* Send the identify message */ + call phase_lock; + cmp LASTPHASE, P_MESGOUT jne p_mesgout_done; + and SCSIDAT,TAG_ENB|SCB_TAG_TYPE,SCB_CONTROL; + call phase_lock; + cmp LASTPHASE, P_MESGOUT jne p_mesgout_done; + mov SCBPTR jmp p_mesgout_onebyte; +/* + * Interrupt the driver, and allow it to handle this message + * phase and any required retries. + */ +p_mesgout_from_host: + cmp SINDEX, HOST_MSG jne p_mesgout_onebyte; + jmp host_message_loop; + +p_mesgout_onebyte: + mvi CLRSINT1, CLRATNO; + mov SCSIDAT, SINDEX; + +/* + * If the next bus phase after ATN drops is message out, it means + * that the target is requesting that the last message(s) be resent. + */ + call phase_lock; + cmp LASTPHASE, P_MESGOUT je p_mesgout_retry; + +p_mesgout_done: + mvi CLRSINT1,CLRATNO; /* Be sure to turn ATNO off */ + mov LAST_MSG, MSG_OUT; + mvi MSG_OUT, MSG_NOOP; /* No message left */ + jmp ITloop; + +/* + * Message in phase. Bytes are read using Automatic PIO mode. + */ +p_mesgin: + /* read the 1st message byte */ + mvi ACCUM call inb_first; + + test A,MSG_IDENTIFYFLAG jnz mesgin_identify; + cmp A,MSG_DISCONNECT je mesgin_disconnect; + cmp A,MSG_SAVEDATAPOINTER je mesgin_sdptrs; + cmp ALLZEROS,A je mesgin_complete; + cmp A,MSG_RESTOREPOINTERS je mesgin_rdptrs; + cmp A,MSG_IGN_WIDE_RESIDUE je mesgin_ign_wide_residue; + cmp A,MSG_NOOP je mesgin_done; + +/* + * Pushed message loop to allow the kernel to + * run it's own message state engine. To avoid an + * extra nop instruction after signaling the kernel, + * we perform the phase_lock before checking to see + * if we should exit the loop and skip the phase_lock + * in the ITloop. Performing back to back phase_locks + * shouldn't hurt, but why do it twice... + */ +host_message_loop: + call phase_lock; /* Benign the first time through. */ + SET_SEQINTCODE(HOST_MSG_LOOP) + cmp RETURN_1, EXIT_MSG_LOOP je ITloop; + cmp RETURN_1, CONT_MSG_LOOP_WRITE jne . + 3; + mov SCSIDAT, RETURN_2; + jmp host_message_loop; + /* Must be CONT_MSG_LOOP_READ */ + mov NONE, SCSIDAT; /* ACK Byte */ + jmp host_message_loop; + +mesgin_ign_wide_residue: + mov SAVED_MODE, MODE_PTR; + SET_MODE(M_SCSI, M_SCSI) + shr NEGOADDR, 4, SAVED_SCSIID; + mov A, NEGCONOPTS; + RESTORE_MODE(SAVED_MODE) + test A, WIDEXFER jz mesgin_reject; + /* Pull the residue byte */ + mvi REG0 call inb_next; + cmp REG0, 0x01 jne mesgin_reject; + test SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL jz . + 2; + test SCB_TASK_ATTRIBUTE, SCB_XFERLEN_ODD jnz mesgin_done; + SET_SEQINTCODE(IGN_WIDE_RES) + jmp mesgin_done; + +mesgin_proto_violation: + SET_SEQINTCODE(PROTO_VIOLATION) + jmp mesgin_done; +mesgin_reject: + mvi MSG_MESSAGE_REJECT call mk_mesg; +mesgin_done: + mov NONE,SCSIDAT; /*dummy read from latch to ACK*/ + jmp ITloop; + +#define INDEX_DISC_LIST(scsiid, lun) \ + and A, 0xC0, scsiid; \ + or SCBPTR, A, lun; \ + clr SCBPTR[1]; \ + and SINDEX, 0x30, scsiid; \ + shr SINDEX, 3; /* Multiply by 2 */ \ + add SINDEX, (SCB_DISCONNECTED_LISTS & 0xFF); \ + mvi SINDEX[1], ((SCB_DISCONNECTED_LISTS >> 8) & 0xFF) + +mesgin_identify: + /* + * Determine whether a target is using tagged or non-tagged + * transactions by first looking at the transaction stored in + * the per-device, disconnected array. If there is no untagged + * transaction for this target, this must be a tagged transaction. + */ + and SAVED_LUN, MSG_IDENTIFY_LUNMASK, A; + INDEX_DISC_LIST(SAVED_SCSIID, SAVED_LUN); + bmov DINDEX, SINDEX, 2; + bmov REG0, SINDIR, 2; + cmp REG0[1], SCB_LIST_NULL je snoop_tag; + /* Untagged. Clear the busy table entry and setup the SCB. */ + bmov DINDIR, ALLONES, 2; + bmov SCBPTR, REG0, 2; + jmp setup_SCB; + +/* + * Here we "snoop" the bus looking for a SIMPLE QUEUE TAG message. + * If we get one, we use the tag returned to find the proper + * SCB. After receiving the tag, look for the SCB at SCB locations tag and + * tag + 256. + */ +snoop_tag: + if ((ahd->flags & AHD_SEQUENCER_DEBUG) != 0) { + or SEQ_FLAGS, 0x80; + } + mov NONE, SCSIDAT; /* ACK Identify MSG */ + call phase_lock; + if ((ahd->flags & AHD_SEQUENCER_DEBUG) != 0) { + or SEQ_FLAGS, 0x1; + } + cmp LASTPHASE, P_MESGIN jne not_found_ITloop; + if ((ahd->flags & AHD_SEQUENCER_DEBUG) != 0) { + or SEQ_FLAGS, 0x2; + } + cmp SCSIBUS, MSG_SIMPLE_Q_TAG jne not_found; +get_tag: + clr SCBPTR[1]; + mvi SCBPTR call inb_next; /* tag value */ +verify_scb: + test SCB_CONTROL,DISCONNECTED jz verify_other_scb; + mov A, SAVED_SCSIID; + cmp SCB_SCSIID, A jne verify_other_scb; + mov A, SAVED_LUN; + cmp SCB_LUN, A je setup_SCB_disconnected; +verify_other_scb: + xor SCBPTR[1], 1; + test SCBPTR[1], 0xFF jnz verify_scb; + jmp not_found; + +/* + * Ensure that the SCB the tag points to is for + * an SCB transaction to the reconnecting target. + */ +setup_SCB: + if ((ahd->flags & AHD_SEQUENCER_DEBUG) != 0) { + or SEQ_FLAGS, 0x10; + } + test SCB_CONTROL,DISCONNECTED jz not_found; +setup_SCB_disconnected: + and SCB_CONTROL,~DISCONNECTED; + clr SEQ_FLAGS; /* make note of IDENTIFY */ + test SCB_SGPTR, SG_LIST_NULL jnz . + 3; + bmov ALLOCFIFO_SCBPTR, SCBPTR, 2; + call allocate_fifo; + /* See if the host wants to send a message upon reconnection */ + test SCB_CONTROL, MK_MESSAGE jz mesgin_done; + mvi HOST_MSG call mk_mesg; + jmp mesgin_done; + +not_found: + SET_SEQINTCODE(NO_MATCH) + jmp mesgin_done; + +not_found_ITloop: + SET_SEQINTCODE(NO_MATCH) + jmp ITloop; + +/* + * We received a "command complete" message. Put the SCB on the complete + * queue and trigger a completion interrupt via the idle loop. Before doing + * so, check to see if there is a residual or the status byte is something + * other than STATUS_GOOD (0). In either of these conditions, we upload the + * SCB back to the host so it can process this information. + */ +mesgin_complete: + + /* + * If ATN is raised, we still want to give the target a message. + * Perhaps there was a parity error on this last message byte. + * Either way, the target should take us to message out phase + * and then attempt to complete the command again. We should use a + * critical section here to guard against a timeout triggering + * for this command and setting ATN while we are still processing + * the completion. + test SCSISIGI, ATNI jnz mesgin_done; + */ + + /* + * If we are identified and have successfully sent the CDB, + * any status will do. Optimize this fast path. + */ + test SCB_CONTROL, STATUS_RCVD jz mesgin_proto_violation; + test SEQ_FLAGS, NOT_IDENTIFIED|NO_CDB_SENT jz complete_accepted; + + /* + * If the target never sent an identify message but instead went + * to mesgin to give an invalid message, let the host abort us. + */ + test SEQ_FLAGS, NOT_IDENTIFIED jnz mesgin_proto_violation; + + /* + * If we recevied good status but never successfully sent the + * cdb, abort the command. + */ + test SCB_SCSI_STATUS,0xff jnz complete_accepted; + test SEQ_FLAGS, NO_CDB_SENT jnz mesgin_proto_violation; +complete_accepted: + + /* + * See if we attempted to deliver a message but the target ingnored us. + */ + test SCB_CONTROL, MK_MESSAGE jz complete_nomsg; + SET_SEQINTCODE(MKMSG_FAILED) +complete_nomsg: + call queue_scb_completion; + jmp await_busfree; + +BEGIN_CRITICAL; +freeze_queue: + /* Cancel any pending select-out. */ + test SSTAT0, SELDO|SELINGO jnz . + 2; + and SCSISEQ0, ~ENSELO; + mov ACCUM_SAVE, A; + clr A; + add QFREEZE_COUNT, 1; + adc QFREEZE_COUNT[1], A; + or SEQ_FLAGS2, SELECTOUT_QFROZEN; + mov A, ACCUM_SAVE ret; +END_CRITICAL; + +/* + * Complete the current FIFO's SCB if data for this same + * SCB is not transferring in the other FIFO. + */ +SET_SRC_MODE M_DFF1; +SET_DST_MODE M_DFF1; +pkt_complete_scb_if_fifos_idle: + bmov ARG_1, SCBPTR, 2; + mvi DFFSXFRCTL, CLRCHN; + SET_MODE(M_SCSI, M_SCSI) + bmov SCBPTR, ARG_1, 2; + test SCB_FIFO_USE_COUNT, 0xFF jnz return; +queue_scb_completion: + test SCB_SCSI_STATUS,0xff jnz bad_status; + /* + * Check for residuals + */ + test SCB_SGPTR, SG_LIST_NULL jnz complete; /* No xfer */ + test SCB_SGPTR, SG_FULL_RESID jnz upload_scb;/* Never xfered */ + test SCB_RESIDUAL_SGPTR, SG_LIST_NULL jz upload_scb; +complete: +BEGIN_CRITICAL; + bmov SCB_NEXT_COMPLETE, COMPLETE_SCB_HEAD, 2; + bmov COMPLETE_SCB_HEAD, SCBPTR, 2 ret; +END_CRITICAL; +bad_status: + cmp SCB_SCSI_STATUS, STATUS_PKT_SENSE je upload_scb; + call freeze_queue; +upload_scb: + /* + * Restore SCB TAG since we reuse this field + * in the sequencer. We don't want to corrupt + * it on the host. + */ + bmov SCB_TAG, SCBPTR, 2; +BEGIN_CRITICAL; + or SCB_SGPTR, SG_STATUS_VALID; + mvi SCB_NEXT_COMPLETE[1], SCB_LIST_NULL; + cmp COMPLETE_DMA_SCB_HEAD[1], SCB_LIST_NULL jne add_dma_scb_tail; + bmov COMPLETE_DMA_SCB_HEAD, SCBPTR, 2; + bmov COMPLETE_DMA_SCB_TAIL, SCBPTR, 2 ret; +add_dma_scb_tail: + bmov REG0, SCBPTR, 2; + bmov SCBPTR, COMPLETE_DMA_SCB_TAIL, 2; + bmov SCB_NEXT_COMPLETE, REG0, 2; + bmov COMPLETE_DMA_SCB_TAIL, REG0, 2 ret; +END_CRITICAL; + +/* + * Is it a disconnect message? Set a flag in the SCB to remind us + * and await the bus going free. If this is an untagged transaction + * store the SCB id for it in our untagged target table for lookup on + * a reselection. + */ +mesgin_disconnect: + /* + * If ATN is raised, we still want to give the target a message. + * Perhaps there was a parity error on this last message byte + * or we want to abort this command. Either way, the target + * should take us to message out phase and then attempt to + * disconnect again. + * XXX - Wait for more testing. + test SCSISIGI, ATNI jnz mesgin_done; + */ + test SEQ_FLAGS, NOT_IDENTIFIED|NO_CDB_SENT + jnz mesgin_proto_violation; + or SCB_CONTROL,DISCONNECTED; + test SCB_CONTROL, TAG_ENB jnz await_busfree; +queue_disc_scb: + bmov REG0, SCBPTR, 2; + INDEX_DISC_LIST(SAVED_SCSIID, SAVED_LUN); + bmov DINDEX, SINDEX, 2; + bmov DINDIR, REG0, 2; + bmov SCBPTR, REG0, 2; + /* FALLTHROUGH */ +await_busfree: + and SIMODE1, ~ENBUSFREE; + if ((ahd->bugs & AHD_BUSFREEREV_BUG) == 0) { + /* + * In the BUSFREEREV_BUG case, the + * busfree status was cleared at the + * beginning of the connection. + */ + mvi CLRSINT1,CLRBUSFREE; + } + mov NONE, SCSIDAT; /* Ack the last byte */ + test MODE_PTR, ~(MK_MODE(M_DFF1, M_DFF1)) + jnz await_busfree_not_m_dff; +SET_SRC_MODE M_DFF1; +SET_DST_MODE M_DFF1; +await_busfree_clrchn: + mvi DFFSXFRCTL, CLRCHN; +await_busfree_not_m_dff: + /* clear target specific flags */ + mvi SEQ_FLAGS, NOT_IDENTIFIED|NO_CDB_SENT; + test SSTAT1,REQINIT|BUSFREE jz .; + /* + * We only set BUSFREE status once either a new + * phase has been detected or we are really + * BUSFREE. This allows the driver to know + * that we are active on the bus even though + * no identified transaction exists should a + * timeout occur while awaiting busfree. + */ + mvi LASTPHASE, P_BUSFREE; + test SSTAT1, BUSFREE jnz idle_loop; + SET_SEQINTCODE(MISSED_BUSFREE) + + +/* + * Save data pointers message: + * Copying RAM values back to SCB, for Save Data Pointers message, but + * only if we've actually been into a data phase to change them. This + * protects against bogus data in scratch ram and the residual counts + * since they are only initialized when we go into data_in or data_out. + * Ack the message as soon as possible. + */ +SET_SRC_MODE M_DFF1; +SET_DST_MODE M_DFF1; +mesgin_sdptrs: + mov NONE,SCSIDAT; /*dummy read from latch to ACK*/ + test SEQ_FLAGS, DPHASE jz ITloop; + call save_pointers; + jmp ITloop; + +save_pointers: + /* + * If we are asked to save our position at the end of the + * transfer, just mark us at the end rather than perform a + * full save. + */ + test SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL jz save_pointers_full; + or SCB_SGPTR, SG_LIST_NULL ret; + +save_pointers_full: + /* + * The SCB_DATAPTR becomes the current SHADDR. + * All other information comes directly from our residual + * state. + */ + bmov SCB_DATAPTR, SHADDR, 8; + bmov SCB_DATACNT, SCB_RESIDUAL_DATACNT, 8 ret; + +/* + * Restore pointers message? Data pointers are recopied from the + * SCB anytime we enter a data phase for the first time, so all + * we need to do is clear the DPHASE flag and let the data phase + * code do the rest. We also reset/reallocate the FIFO to make + * sure we have a clean start for the next data or command phase. + */ +mesgin_rdptrs: + and SEQ_FLAGS, ~DPHASE; + test MODE_PTR, ~(MK_MODE(M_DFF1, M_DFF1)) jnz msgin_rdptrs_get_fifo; + mvi DFFSXFRCTL, RSTCHN|CLRSHCNT; + SET_MODE(M_SCSI, M_SCSI) +msgin_rdptrs_get_fifo: + call allocate_fifo; + jmp mesgin_done; + +phase_lock: + if ((ahd->bugs & AHD_EARLY_REQ_BUG) != 0) { + /* + * Don't ignore persistent REQ assertions just because + * they were asserted within the bus settle delay window. + * This allows us to tolerate devices like the GEM318 + * that violate the SCSI spec. We are careful not to + * count REQ while we are waiting for it to fall during + * an async phase due to our asserted ACK. Each + * sequencer instruction takes ~25ns, so the REQ must + * last at least 100ns in order to be counted as a true + * REQ. + */ + test SCSIPHASE, 0xFF jnz phase_locked; + test SCSISIGI, ACKI jnz phase_lock; + test SCSISIGI, REQI jz phase_lock; + test SCSIPHASE, 0xFF jnz phase_locked; + test SCSISIGI, ACKI jnz phase_lock; + test SCSISIGI, REQI jz phase_lock; +phase_locked: + } else { + test SCSIPHASE, 0xFF jz .; + } + test SSTAT1, SCSIPERR jnz phase_lock; +phase_lock_latch_phase: + and LASTPHASE, PHASE_MASK, SCSISIGI ret; + +/* + * Functions to read data in Automatic PIO mode. + * + * An ACK is not sent on input from the target until SCSIDATL is read from. + * So we wait until SCSIDATL is latched (the usual way), then read the data + * byte directly off the bus using SCSIBUSL. When we have pulled the ATN + * line, or we just want to acknowledge the byte, then we do a dummy read + * from SCISDATL. The SCSI spec guarantees that the target will hold the + * data byte on the bus until we send our ACK. + * + * The assumption here is that these are called in a particular sequence, + * and that REQ is already set when inb_first is called. inb_{first,next} + * use the same calling convention as inb. + */ +inb_next: + mov NONE,SCSIDAT; /*dummy read from latch to ACK*/ +inb_next_wait: + /* + * If there is a parity error, wait for the kernel to + * see the interrupt and prepare our message response + * before continuing. + */ + test SCSIPHASE, 0xFF jz .; + test SSTAT1, SCSIPERR jnz inb_next_wait; +inb_next_check_phase: + and LASTPHASE, PHASE_MASK, SCSISIGI; + cmp LASTPHASE, P_MESGIN jne mesgin_phasemis; +inb_first: + clr DINDEX[1]; + mov DINDEX,SINDEX; + mov DINDIR,SCSIBUS ret; /*read byte directly from bus*/ +inb_last: + mov NONE,SCSIDAT ret; /*dummy read from latch to ACK*/ + +mk_mesg: + mvi SCSISIGO, ATNO; + mov MSG_OUT,SINDEX ret; + +SET_SRC_MODE M_DFF1; +SET_DST_MODE M_DFF1; +disable_ccsgen: + test SG_STATE, FETCH_INPROG jz disable_ccsgen_fetch_done; + clr CCSGCTL; +disable_ccsgen_fetch_done: + clr SG_STATE ret; + +service_fifo: + /* + * Do we have any prefetch left??? + */ + test SG_STATE, SEGS_AVAIL jnz idle_sg_avail; + + /* + * Can this FIFO have access to the S/G cache yet? + */ + test CCSGCTL, SG_CACHE_AVAIL jz return; + + /* Did we just finish fetching segs? */ + test CCSGCTL, CCSGDONE jnz idle_sgfetch_complete; + + /* Are we actively fetching segments? */ + test CCSGCTL, CCSGENACK jnz return; + + /* + * Should the other FIFO get the S/G cache first? If + * both FIFOs have been allocated since we last checked + * any FIFO, it is important that we service a FIFO + * that is not actively on the bus first. This guarantees + * that a FIFO will be freed to handle snapshot requests for + * any FIFO that is still on the bus. Chips with RTI do not + * perform snapshots, so don't bother with this test there. + */ + if ((ahd->features & AHD_RTI) == 0) { + /* + * If we're not still receiving SCSI data, + * it is safe to allocate the S/G cache to + * this FIFO. + */ + test DFCNTRL, SCSIEN jz idle_sgfetch_start; + + /* + * Switch to the other FIFO. Non-RTI chips + * also have the "set mode" bug, so we must + * disable interrupts during the switch. + */ + mvi SEQINTCTL, INTVEC1DSL; + xor MODE_PTR, MK_MODE(M_DFF1, M_DFF1); + + /* + * If the other FIFO needs loading, then it + * must not have claimed the S/G cache yet + * (SG_CACHE_AVAIL would have been cleared in + * the original FIFO mode and we test this above). + * Return to the idle loop so we can process the + * FIFO not currently on the bus first. + */ + test SG_STATE, LOADING_NEEDED jz idle_sgfetch_okay; + clr SEQINTCTL ret; +idle_sgfetch_okay: + xor MODE_PTR, MK_MODE(M_DFF1, M_DFF1); + clr SEQINTCTL; + } + +idle_sgfetch_start: + /* + * We fetch a "cacheline aligned" and sized amount of data + * so we don't end up referencing a non-existent page. + * Cacheline aligned is in quotes because the kernel will + * set the prefetch amount to a reasonable level if the + * cacheline size is unknown. + */ + bmov SGHADDR, SCB_RESIDUAL_SGPTR, 4; + mvi SGHCNT, SG_PREFETCH_CNT; + if ((ahd->bugs & AHD_REG_SLOW_SETTLE_BUG) != 0) { + /* + * Need two instructions between "touches" of SGHADDR. + */ + nop; + } + and SGHADDR[0], SG_PREFETCH_ALIGN_MASK, SCB_RESIDUAL_SGPTR; + mvi CCSGCTL, CCSGEN|CCSGRESET; + or SG_STATE, FETCH_INPROG ret; +idle_sgfetch_complete: + /* + * Guard against SG_CACHE_AVAIL activating during sg fetch + * request in the other FIFO. + */ + test SG_STATE, FETCH_INPROG jz return; + clr CCSGCTL; + and CCSGADDR, SG_PREFETCH_ADDR_MASK, SCB_RESIDUAL_SGPTR; + mvi SG_STATE, SEGS_AVAIL|LOADING_NEEDED; +idle_sg_avail: + /* Does the hardware have space for another SG entry? */ + test DFSTATUS, PRELOAD_AVAIL jz return; + /* + * On the A, preloading a segment before HDMAENACK + * comes true can clobber the shadow address of the + * first segment in the S/G FIFO. Wait until it is + * safe to proceed. + */ + if ((ahd->features & AHD_NEW_DFCNTRL_OPTS) == 0) { + test DFCNTRL, HDMAENACK jz return; + } + if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) { + bmov HADDR, CCSGRAM, 8; + } else { + bmov HADDR, CCSGRAM, 4; + } + bmov HCNT, CCSGRAM, 3; + bmov SCB_RESIDUAL_DATACNT[3], CCSGRAM, 1; + if ((ahd->flags & AHD_39BIT_ADDRESSING) != 0) { + and HADDR[4], SG_HIGH_ADDR_BITS, SCB_RESIDUAL_DATACNT[3]; + } + if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) { + /* Skip 4 bytes of pad. */ + add CCSGADDR, 4; + } +sg_advance: + clr A; /* add sizeof(struct scatter) */ + add SCB_RESIDUAL_SGPTR[0],SG_SIZEOF; + adc SCB_RESIDUAL_SGPTR[1],A; + adc SCB_RESIDUAL_SGPTR[2],A; + adc SCB_RESIDUAL_SGPTR[3],A; + mov SINDEX, SCB_RESIDUAL_SGPTR[0]; + test SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG jz . + 3; + or SINDEX, LAST_SEG; + clr SG_STATE; + mov SG_CACHE_PRE, SINDEX; + if ((ahd->features & AHD_NEW_DFCNTRL_OPTS) != 0) { + /* + * Use SCSIENWRDIS so that SCSIEN is never + * modified by this operation. + */ + or DFCNTRL, PRELOADEN|HDMAEN|SCSIENWRDIS; + } else { + or DFCNTRL, PRELOADEN|HDMAEN; + } + /* + * Do we have another segment in the cache? + */ + add NONE, SG_PREFETCH_CNT_LIMIT, CCSGADDR; + jnc return; + and SG_STATE, ~SEGS_AVAIL ret; + +/* + * Initialize the DMA address and counter from the SCB. + */ +load_first_seg: + bmov HADDR, SCB_DATAPTR, 11; + and REG_ISR, ~SG_FULL_RESID, SCB_SGPTR[0]; + test SCB_DATACNT[3], SG_LAST_SEG jz . + 2; + or REG_ISR, LAST_SEG; + mov SG_CACHE_PRE, REG_ISR; + mvi DFCNTRL, (PRELOADEN|SCSIEN|HDMAEN); + /* + * Since we've are entering a data phase, we will + * rely on the SCB_RESID* fields. Initialize the + * residual and clear the full residual flag. + */ + and SCB_SGPTR[0], ~SG_FULL_RESID; + bmov SCB_RESIDUAL_DATACNT[3], SCB_DATACNT[3], 5; + /* If we need more S/G elements, tell the idle loop */ + test SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG jnz . + 2; + mvi SG_STATE, LOADING_NEEDED ret; + clr SG_STATE ret; + +p_data_handle_xfer: + call setjmp; + test SG_STATE, LOADING_NEEDED jnz service_fifo; +p_data_clear_handler: + or LONGJMP_ADDR[1], INVALID_ADDR ret; + +p_data: + test SEQ_FLAGS, NOT_IDENTIFIED|NO_CDB_SENT jz p_data_allowed; + SET_SEQINTCODE(PROTO_VIOLATION) +p_data_allowed: + + test SEQ_FLAGS, DPHASE jz data_phase_initialize; + + /* + * If we re-enter the data phase after going through another + * phase, our transfer location has almost certainly been + * corrupted by the interveining, non-data, transfers. Ask + * the host driver to fix us up based on the transfer residual + * unless we already know that we should be bitbucketing. + */ + test SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL jnz p_data_bitbucket; + SET_SEQINTCODE(PDATA_REINIT) + jmp data_phase_inbounds; + +p_data_bitbucket: + /* + * Turn on `Bit Bucket' mode, wait until the target takes + * us to another phase, and then notify the host. + */ + mov SAVED_MODE, MODE_PTR; + test MODE_PTR, ~(MK_MODE(M_DFF1, M_DFF1)) + jnz bitbucket_not_m_dff; + /* + * Ensure that any FIFO contents are cleared out and the + * FIFO free'd prior to starting the BITBUCKET. BITBUCKET + * doesn't discard data already in the FIFO. + */ + mvi DFFSXFRCTL, RSTCHN|CLRSHCNT; + SET_MODE(M_SCSI, M_SCSI) +bitbucket_not_m_dff: + or SXFRCTL1,BITBUCKET; + /* Wait for non-data phase. */ + test SCSIPHASE, ~DATA_PHASE_MASK jz .; + and SXFRCTL1, ~BITBUCKET; + RESTORE_MODE(SAVED_MODE) +SET_SRC_MODE M_DFF1; +SET_DST_MODE M_DFF1; + SET_SEQINTCODE(DATA_OVERRUN) + jmp ITloop; + +data_phase_initialize: + test SCB_SGPTR[0], SG_LIST_NULL jnz p_data_bitbucket; + call load_first_seg; +data_phase_inbounds: + /* We have seen a data phase at least once. */ + or SEQ_FLAGS, DPHASE; + mov SAVED_MODE, MODE_PTR; + test SG_STATE, LOADING_NEEDED jz data_group_dma_loop; + call p_data_handle_xfer; +data_group_dma_loop: + /* + * The transfer is complete if either the last segment + * completes or the target changes phase. Both conditions + * will clear SCSIEN. + */ + call idle_loop_service_fifos; + call idle_loop_cchan; + call idle_loop_gsfifo; + RESTORE_MODE(SAVED_MODE) + test DFCNTRL, SCSIEN jnz data_group_dma_loop; + +data_group_dmafinish: + /* + * The transfer has terminated either due to a phase + * change, and/or the completion of the last segment. + * We have two goals here. Do as much other work + * as possible while the data fifo drains on a read + * and respond as quickly as possible to the standard + * messages (save data pointers/disconnect and command + * complete) that usually follow a data phase. + */ + call calc_residual; + + /* + * Go ahead and shut down the DMA engine now. + */ + test DFCNTRL, DIRECTION jnz data_phase_finish; +data_group_fifoflush: + if ((ahd->bugs & AHD_AUTOFLUSH_BUG) != 0) { + or DFCNTRL, FIFOFLUSH; + } + /* + * We have enabled the auto-ack feature. This means + * that the controller may have already transferred + * some overrun bytes into the data FIFO and acked them + * on the bus. The only way to detect this situation is + * to wait for LAST_SEG_DONE to come true on a completed + * transfer and then test to see if the data FIFO is + * non-empty. We know there is more data yet to transfer + * if SG_LIST_NULL is not yet set, thus there cannot be + * an overrun. + */ + test SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL jz data_phase_finish; + test SG_CACHE_SHADOW, LAST_SEG_DONE jz .; + test DFSTATUS, FIFOEMP jnz data_phase_finish; + /* Overrun */ + jmp p_data; +data_phase_finish: + /* + * If the target has left us in data phase, loop through + * the dma code again. We will only loop if there is a + * data overrun. + */ + if ((ahd->flags & AHD_TARGETROLE) != 0) { + test SSTAT0, TARGET jnz data_phase_done; + } + if ((ahd->flags & AHD_INITIATORROLE) != 0) { + test SSTAT1, REQINIT jz .; + test SCSIPHASE, DATA_PHASE_MASK jnz p_data; + } + +data_phase_done: + /* Kill off any pending prefetch */ + call disable_ccsgen; + or LONGJMP_ADDR[1], INVALID_ADDR; + + if ((ahd->flags & AHD_TARGETROLE) != 0) { + test SEQ_FLAGS, DPHASE_PENDING jz ITloop; + /* + and SEQ_FLAGS, ~DPHASE_PENDING; + * For data-in phases, wait for any pending acks from the + * initiator before changing phase. We only need to + * send Ignore Wide Residue messages for data-in phases. + test DFCNTRL, DIRECTION jz target_ITloop; + test SSTAT1, REQINIT jnz .; + test SCB_TASK_ATTRIBUTE, SCB_XFERLEN_ODD jz target_ITloop; + SET_MODE(M_SCSI, M_SCSI) + test NEGCONOPTS, WIDEXFER jz target_ITloop; + */ + /* + * Issue an Ignore Wide Residue Message. + mvi P_MESGIN|BSYO call change_phase; + mvi MSG_IGN_WIDE_RESIDUE call target_outb; + mvi 1 call target_outb; + jmp target_ITloop; + */ + } else { + jmp ITloop; + } + +/* + * We assume that, even though data may still be + * transferring to the host, that the SCSI side of + * the DMA engine is now in a static state. This + * allows us to update our notion of where we are + * in this transfer. + * + * If, by chance, we stopped before being able + * to fetch additional segments for this transfer, + * yet the last S/G was completely exhausted, + * call our idle loop until it is able to load + * another segment. This will allow us to immediately + * pickup on the next segment on the next data phase. + * + * If we happened to stop on the last segment, then + * our residual information is still correct from + * the idle loop and there is no need to perform + * any fixups. + */ +residual_before_last_seg: + test MDFFSTAT, SHVALID jnz sgptr_fixup; + /* + * Can never happen from an interrupt as the packetized + * hardware will only interrupt us once SHVALID or + * LAST_SEG_DONE. + */ + call idle_loop_service_fifos; + RESTORE_MODE(SAVED_MODE) + /* FALLTHROUGH */ +calc_residual: + test SG_CACHE_SHADOW, LAST_SEG jz residual_before_last_seg; + /* Record if we've consumed all S/G entries */ + test MDFFSTAT, SHVALID jz . + 2; + bmov SCB_RESIDUAL_DATACNT, SHCNT, 3 ret; + or SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL ret; + +sgptr_fixup: + /* + * Fixup the residual next S/G pointer. The S/G preload + * feature of the chip allows us to load two elements + * in addition to the currently active element. We + * store the bottom byte of the next S/G pointer in + * the SG_CACHE_PTR register so we can restore the + * correct value when the DMA completes. If the next + * sg ptr value has advanced to the point where higher + * bytes in the address have been affected, fix them + * too. + */ + test SG_CACHE_SHADOW, 0x80 jz sgptr_fixup_done; + test SCB_RESIDUAL_SGPTR[0], 0x80 jnz sgptr_fixup_done; + add SCB_RESIDUAL_SGPTR[1], -1; + adc SCB_RESIDUAL_SGPTR[2], -1; + adc SCB_RESIDUAL_SGPTR[3], -1; +sgptr_fixup_done: + and SCB_RESIDUAL_SGPTR[0], SG_ADDR_MASK, SG_CACHE_SHADOW; + clr SCB_RESIDUAL_DATACNT[3]; /* We are not the last seg */ + bmov SCB_RESIDUAL_DATACNT, SHCNT, 3 ret; + +export timer_isr: + call issue_cmdcmplt; + mvi CLRSEQINTSTAT, CLRSEQ_SWTMRTO; + if ((ahd->bugs & AHD_SET_MODE_BUG) != 0) { + /* + * In H2A4, the mode pointer is not saved + * for intvec2, but is restored on iret. + * This can lead to the restoration of a + * bogus mode ptr. Manually clear the + * intmask bits and do a normal return + * to compensate. + */ + and SEQINTCTL, ~(INTMASK2|INTMASK1) ret; + } else { + or SEQINTCTL, IRET ret; + } + +export seq_isr: + if ((ahd->features & AHD_RTI) == 0) { + /* + * On RevA Silicon, if the target returns us to data-out + * after we have already trained for data-out, it is + * possible for us to transition the free running clock to + * data-valid before the required 100ns P1 setup time (8 P1 + * assertions in fast-160 mode). This will only happen if + * this L-Q is a continuation of a data transfer for which + * we have already prefetched data into our FIFO (LQ/Data + * followed by LQ/Data for the same write transaction). + * This can cause some target implementations to miss the + * first few data transfers on the bus. We detect this + * situation by noticing that this is the first data transfer + * after an LQ (LQIWORKONLQ true), that the data transfer is + * a continuation of a transfer already setup in our FIFO + * (SAVEPTRS interrupt), and that the transaction is a write + * (DIRECTION set in DFCNTRL). The delay is performed by + * disabling SCSIEN until we see the first REQ from the + * target. + * + * First instruction in an ISR cannot be a branch on + * Rev A. Snapshot LQISTAT2 so the status is not missed + * and deffer the test by one instruction. + */ + mov REG_ISR, LQISTAT2; + test REG_ISR, LQIWORKONLQ jz main_isr; + test SEQINTSRC, SAVEPTRS jz main_isr; + test LONGJMP_ADDR[1], INVALID_ADDR jz saveptr_active_fifo; + /* + * Switch to the active FIFO after clearing the snapshot + * savepointer in the current FIFO. We do this so that + * a pending CTXTDONE or SAVEPTR is visible in the active + * FIFO. This status is the only way we can detect if we + * have lost the race (e.g. host paused us) and our attempts + * to disable the channel occurred after all REQs were + * already seen and acked (REQINIT never comes true). + */ + mvi DFFSXFRCTL, CLRCHN; + xor MODE_PTR, MK_MODE(M_DFF1, M_DFF1); + test DFCNTRL, DIRECTION jz interrupt_return; + and DFCNTRL, ~SCSIEN; +snapshot_wait_data_valid: + test SEQINTSRC, (CTXTDONE|SAVEPTRS) jnz interrupt_return; + test SSTAT1, REQINIT jz snapshot_wait_data_valid; +snapshot_data_valid: + or DFCNTRL, SCSIEN; + or SEQINTCTL, IRET ret; +snapshot_saveptr: + mvi DFFSXFRCTL, CLRCHN; + or SEQINTCTL, IRET ret; +main_isr: + } + test SEQINTSRC, CFG4DATA jnz cfg4data_intr; + test SEQINTSRC, CFG4ISTAT jnz cfg4istat_intr; + test SEQINTSRC, SAVEPTRS jnz saveptr_intr; + test SEQINTSRC, CFG4ICMD jnz cfg4icmd_intr; + SET_SEQINTCODE(INVALID_SEQINT) + +/* + * There are two types of save pointers interrupts: + * The first is a snapshot save pointers where the current FIFO is not + * active and contains a snapshot of the current poniter information. + * This happens between packets in a stream for a single L_Q. Since we + * are not performing a pointer save, we can safely clear the channel + * so it can be used for other transactions. On RTI capable controllers, + * where snapshots can, and are, disabled, the code to handle this type + * of snapshot is not active. + * + * The second case is a save pointers on an active FIFO which occurs + * if the target changes to a new L_Q or busfrees/QASes and the transfer + * has a residual. This should occur coincident with a ctxtdone. We + * disable the interrupt and allow our active routine to handle the + * save. + */ +saveptr_intr: + if ((ahd->features & AHD_RTI) == 0) { + test LONGJMP_ADDR[1], INVALID_ADDR jnz snapshot_saveptr; + } +saveptr_active_fifo: + and SEQIMODE, ~ENSAVEPTRS; + or SEQINTCTL, IRET ret; + +cfg4data_intr: + test SCB_SGPTR[0], SG_LIST_NULL jnz pkt_handle_overrun_inc_use_count; + call load_first_seg; + call pkt_handle_xfer; + inc SCB_FIFO_USE_COUNT; +interrupt_return: + or SEQINTCTL, IRET ret; + +cfg4istat_intr: + call freeze_queue; + add NONE, -13, SCB_CDB_LEN; + jnc cfg4istat_have_sense_addr; + test SCB_CDB_LEN, SCB_CDB_LEN_PTR jnz cfg4istat_have_sense_addr; + /* + * Host sets up address/count and enables transfer. + */ + SET_SEQINTCODE(CFG4ISTAT_INTR) + jmp cfg4istat_setup_handler; +cfg4istat_have_sense_addr: + bmov HADDR, SCB_SENSE_BUSADDR, 4; + mvi HCNT[1], (AHD_SENSE_BUFSIZE >> 8); + mvi SG_CACHE_PRE, LAST_SEG; + mvi DFCNTRL, PRELOADEN|SCSIEN|HDMAEN; +cfg4istat_setup_handler: + /* + * Status pkt is transferring to host. + * Wait in idle loop for transfer to complete. + * If a command completed before an attempted + * task management function completed, notify the host. + */ + test SCB_TASK_MANAGEMENT, 0xFF jz cfg4istat_no_taskmgmt_func; + SET_SEQINTCODE(TASKMGMT_CMD_CMPLT_OKAY) +cfg4istat_no_taskmgmt_func: + call pkt_handle_status; + or SEQINTCTL, IRET ret; + +cfg4icmd_intr: + /* + * In the case of DMAing a CDB from the host, the normal + * CDB buffer is formatted with an 8 byte address followed + * by a 1 byte count. + */ + bmov HADDR[0], SCB_HOST_CDB_PTR, 9; + mvi SG_CACHE_PRE, LAST_SEG; + mvi DFCNTRL, (PRELOADEN|SCSIEN|HDMAEN); + call pkt_handle_cdb; + or SEQINTCTL, IRET ret; + +/* + * See if the target has gone on in this context creating an + * overrun condition. For the write case, the hardware cannot + * ack bytes until data are provided. So, if the target begins + * another packet without changing contexts, implying we are + * not sitting on a packet boundary, we are in an overrun + * situation. For the read case, the hardware will continue to + * ack bytes into the FIFO, and may even ack the last overrun packet + * into the FIFO. If the FIFO should become non-empty, we are in + * a read overrun case. + */ +#define check_overrun \ + /* Not on a packet boundary. */ \ + test MDFFSTAT, DLZERO jz pkt_handle_overrun; \ + test DFSTATUS, FIFOEMP jz pkt_handle_overrun + +pkt_handle_xfer: + test SG_STATE, LOADING_NEEDED jz pkt_last_seg; + call setjmp; + test SEQINTSRC, SAVEPTRS jnz pkt_saveptrs; + test SCSIPHASE, ~DATA_PHASE_MASK jz . + 2; + test SCSISIGO, ATNO jnz . + 2; + test SSTAT2, NONPACKREQ jz pkt_service_fifo; + /* + * Defer handling of this NONPACKREQ until we + * can be sure it pertains to this FIFO. SAVEPTRS + * will not be asserted if the NONPACKREQ is for us, + * so we must simulate it if shadow is valid. If + * shadow is not valid, keep running this FIFO until we + * have satisfied the transfer by loading segments and + * waiting for either shadow valid or last_seg_done. + */ + test MDFFSTAT, SHVALID jnz pkt_saveptrs; +pkt_service_fifo: + test SG_STATE, LOADING_NEEDED jnz service_fifo; +pkt_last_seg: + call setjmp; + test SEQINTSRC, SAVEPTRS jnz pkt_saveptrs; + test SG_CACHE_SHADOW, LAST_SEG_DONE jnz pkt_last_seg_done; + test SCSIPHASE, ~DATA_PHASE_MASK jz . + 2; + test SCSISIGO, ATNO jnz . + 2; + test SSTAT2, NONPACKREQ jz return; + test MDFFSTAT, SHVALID jz return; + /* FALLTHROUGH */ + +/* + * Either a SAVEPTRS interrupt condition is pending for this FIFO + * or we have a pending NONPACKREQ for this FIFO. We differentiate + * between the two by capturing the state of the SAVEPTRS interrupt + * prior to clearing this status and executing the common code for + * these two cases. + */ +pkt_saveptrs: +BEGIN_CRITICAL; + if ((ahd->bugs & AHD_AUTOFLUSH_BUG) != 0) { + or DFCNTRL, FIFOFLUSH; + } + mov REG0, SEQINTSRC; + call calc_residual; + call save_pointers; + mvi CLRSEQINTSRC, CLRSAVEPTRS; + call disable_ccsgen; + or SEQIMODE, ENSAVEPTRS; + test DFCNTRL, DIRECTION jnz pkt_saveptrs_check_status; + test DFSTATUS, FIFOEMP jnz pkt_saveptrs_check_status; + /* + * Keep a handler around for this FIFO until it drains + * to the host to guarantee that we don't complete the + * command to the host before the data arrives. + */ +pkt_saveptrs_wait_fifoemp: + call setjmp; + test DFSTATUS, FIFOEMP jz return; +pkt_saveptrs_check_status: + or LONGJMP_ADDR[1], INVALID_ADDR; + test REG0, SAVEPTRS jz unexpected_nonpkt_phase; + dec SCB_FIFO_USE_COUNT; + test SCB_CONTROL, STATUS_RCVD jnz pkt_complete_scb_if_fifos_idle; + mvi DFFSXFRCTL, CLRCHN ret; + +/* + * LAST_SEG_DONE status has been seen in the current FIFO. + * This indicates that all of the allowed data for this + * command has transferred across the SCSI and host buses. + * Check for overrun and see if we can complete this command. + */ +pkt_last_seg_done: + /* + * Mark transfer as completed. + */ + or SCB_SGPTR, SG_LIST_NULL; + + /* + * Wait for the current context to finish to verify that + * no overrun condition has occurred. + */ + test SEQINTSRC, CTXTDONE jnz pkt_ctxt_done; + call setjmp; +pkt_wait_ctxt_done_loop: + test SEQINTSRC, CTXTDONE jnz pkt_ctxt_done; + /* + * A sufficiently large overrun or a NONPACKREQ may + * prevent CTXTDONE from ever asserting, so we must + * poll for these statuses too. + */ + check_overrun; + test SSTAT2, NONPACKREQ jz return; + test SEQINTSRC, CTXTDONE jz unexpected_nonpkt_phase; + /* FALLTHROUGH */ + +pkt_ctxt_done: + check_overrun; + or LONGJMP_ADDR[1], INVALID_ADDR; + /* + * If status has been received, it is safe to skip + * the check to see if another FIFO is active because + * LAST_SEG_DONE has been observed. However, we check + * the FIFO anyway since it costs us only one extra + * instruction to leverage common code to perform the + * SCB completion. + */ + dec SCB_FIFO_USE_COUNT; + test SCB_CONTROL, STATUS_RCVD jnz pkt_complete_scb_if_fifos_idle; + mvi DFFSXFRCTL, CLRCHN ret; +END_CRITICAL; + +/* + * Must wait until CDB xfer is over before issuing the + * clear channel. + */ +pkt_handle_cdb: + call setjmp; + test SG_CACHE_SHADOW, LAST_SEG_DONE jz return; + or LONGJMP_ADDR[1], INVALID_ADDR; + mvi DFFSXFRCTL, CLRCHN ret; + +/* + * Watch over the status transfer. Our host sense buffer is + * large enough to take the maximum allowed status packet. + * None-the-less, we must still catch and report overruns to + * the host. Additionally, properly catch unexpected non-packet + * phases that are typically caused by CRC errors in status packet + * transmission. + */ +pkt_handle_status: + call setjmp; + test SG_CACHE_SHADOW, LAST_SEG_DONE jnz pkt_status_check_overrun; + test SEQINTSRC, CTXTDONE jz pkt_status_check_nonpackreq; + test SG_CACHE_SHADOW, LAST_SEG_DONE jnz pkt_status_check_overrun; +pkt_status_IU_done: + if ((ahd->bugs & AHD_AUTOFLUSH_BUG) != 0) { + or DFCNTRL, FIFOFLUSH; + } + test DFSTATUS, FIFOEMP jz return; +BEGIN_CRITICAL; + or LONGJMP_ADDR[1], INVALID_ADDR; + mvi SCB_SCSI_STATUS, STATUS_PKT_SENSE; + or SCB_CONTROL, STATUS_RCVD; + jmp pkt_complete_scb_if_fifos_idle; +END_CRITICAL; +pkt_status_check_overrun: + /* + * Status PKT overruns are uncerimoniously recovered with a + * bus reset. If we've overrun, let the host know so that + * recovery can be performed. + * + * LAST_SEG_DONE has been observed. If either CTXTDONE or + * a NONPACKREQ phase change have occurred and the FIFO is + * empty, there is no overrun. + */ + test DFSTATUS, FIFOEMP jz pkt_status_report_overrun; + test SEQINTSRC, CTXTDONE jz . + 2; + test DFSTATUS, FIFOEMP jnz pkt_status_IU_done; + test SCSIPHASE, ~DATA_PHASE_MASK jz return; + test DFSTATUS, FIFOEMP jnz pkt_status_check_nonpackreq; +pkt_status_report_overrun: + SET_SEQINTCODE(STATUS_OVERRUN) + /* SEQUENCER RESTARTED */ +pkt_status_check_nonpackreq: + /* + * CTXTDONE may be held off if a NONPACKREQ is associated with + * the current context. If a NONPACKREQ is observed, decide + * if it is for the current context. If it is for the current + * context, we must defer NONPACKREQ processing until all data + * has transferred to the host. + */ + test SCSIPHASE, ~DATA_PHASE_MASK jz return; + test SCSISIGO, ATNO jnz . + 2; + test SSTAT2, NONPACKREQ jz return; + test SEQINTSRC, CTXTDONE jnz pkt_status_IU_done; + test DFSTATUS, FIFOEMP jz return; + /* + * The unexpected nonpkt phase handler assumes that any + * data channel use will have a FIFO reference count. It + * turns out that the status handler doesn't need a references + * count since the status received flag, and thus completion + * processing, cannot be set until the handler is finished. + * We increment the count here to make the nonpkt handler + * happy. + */ + inc SCB_FIFO_USE_COUNT; + /* FALLTHROUGH */ + +/* + * Nonpackreq is a polled status. It can come true in three situations: + * we have received an L_Q, we have sent one or more L_Qs, or there is no + * L_Q context associated with this REQ (REQ occurs immediately after a + * (re)selection). Routines that know that the context responsible for this + * nonpackreq call directly into unexpected_nonpkt_phase. In the case of the + * top level idle loop, we exhaust all active contexts prior to determining that + * we simply do not have the full I_T_L_Q for this phase. + */ +unexpected_nonpkt_phase_find_ctxt: + /* + * This nonpackreq is most likely associated with one of the tags + * in a FIFO or an outgoing LQ. Only treat it as an I_T only + * nonpackreq if we've cleared out the FIFOs and handled any + * pending SELDO. + */ +SET_SRC_MODE M_SCSI; +SET_DST_MODE M_SCSI; + and A, FIFO1FREE|FIFO0FREE, DFFSTAT; + cmp A, FIFO1FREE|FIFO0FREE jne return; + test SSTAT0, SELDO jnz return; + mvi SCBPTR[1], SCB_LIST_NULL; +unexpected_nonpkt_phase: + test MODE_PTR, ~(MK_MODE(M_DFF1, M_DFF1)) + jnz unexpected_nonpkt_mode_cleared; +SET_SRC_MODE M_DFF0; +SET_DST_MODE M_DFF0; + or LONGJMP_ADDR[1], INVALID_ADDR; + dec SCB_FIFO_USE_COUNT; + mvi DFFSXFRCTL, CLRCHN; +unexpected_nonpkt_mode_cleared: + mvi CLRSINT2, CLRNONPACKREQ; + if ((ahd->bugs & AHD_BUSFREEREV_BUG) != 0) { + /* + * Test to ensure that the bus has not + * already gone free prior to clearing + * any stale busfree status. This avoids + * a window whereby a busfree just after + * a selection could be missed. + */ + test SCSISIGI, BSYI jz . + 2; + mvi CLRSINT1,CLRBUSFREE; + or SIMODE1, ENBUSFREE; + } + test SCSIPHASE, ~(MSG_IN_PHASE|MSG_OUT_PHASE) jnz illegal_phase; + SET_SEQINTCODE(ENTERING_NONPACK) + jmp ITloop; + +illegal_phase: + SET_SEQINTCODE(ILLEGAL_PHASE) + jmp ITloop; + +/* + * We have entered an overrun situation. If we have working + * BITBUCKET, flip that on and let the hardware eat any overrun + * data. Otherwise use an overrun buffer in the host to simulate + * BITBUCKET. + */ +pkt_handle_overrun_inc_use_count: + inc SCB_FIFO_USE_COUNT; +pkt_handle_overrun: + SET_SEQINTCODE(CFG4OVERRUN) + call freeze_queue; + if ((ahd->bugs & AHD_PKT_BITBUCKET_BUG) == 0) { + or DFFSXFRCTL, DFFBITBUCKET; +SET_SRC_MODE M_DFF1; +SET_DST_MODE M_DFF1; + } else { + call load_overrun_buf; + mvi DFCNTRL, (HDMAEN|SCSIEN|PRELOADEN); + } + call setjmp; + if ((ahd->bugs & AHD_PKT_BITBUCKET_BUG) != 0) { + test DFSTATUS, PRELOAD_AVAIL jz overrun_load_done; + call load_overrun_buf; + or DFCNTRL, PRELOADEN; +overrun_load_done: + test SEQINTSRC, CTXTDONE jnz pkt_overrun_end; + } else { + test DFFSXFRCTL, DFFBITBUCKET jz pkt_overrun_end; + } + test SSTAT2, NONPACKREQ jz return; +pkt_overrun_end: + or SCB_RESIDUAL_SGPTR, SG_OVERRUN_RESID; + test SEQINTSRC, CTXTDONE jz unexpected_nonpkt_phase; + dec SCB_FIFO_USE_COUNT; + or LONGJMP_ADDR[1], INVALID_ADDR; + test SCB_CONTROL, STATUS_RCVD jnz pkt_complete_scb_if_fifos_idle; + mvi DFFSXFRCTL, CLRCHN ret; + +if ((ahd->bugs & AHD_PKT_BITBUCKET_BUG) != 0) { +load_overrun_buf: + /* + * Load a dummy segment if preload space is available. + */ + mov HADDR[0], SHARED_DATA_ADDR; + add HADDR[1], PKT_OVERRUN_BUFOFFSET, SHARED_DATA_ADDR[1]; + mov ACCUM_SAVE, A; + clr A; + adc HADDR[2], A, SHARED_DATA_ADDR[2]; + adc HADDR[3], A, SHARED_DATA_ADDR[3]; + mov A, ACCUM_SAVE; + bmov HADDR[4], ALLZEROS, 4; + /* PKT_OVERRUN_BUFSIZE is a multiple of 256 */ + clr HCNT[0]; + mvi HCNT[1], ((PKT_OVERRUN_BUFSIZE >> 8) & 0xFF); + clr HCNT[2] ret; +} diff --git a/drivers/scsi/aic7xxx/aic79xx_core.c b/drivers/scsi/aic7xxx/aic79xx_core.c new file mode 100644 index 000000000..98b02e7d3 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx_core.c @@ -0,0 +1,10729 @@ +/* + * Core routines and tables shareable across OS platforms. + * + * Copyright (c) 1994-2002 Justin T. Gibbs. + * Copyright (c) 2000-2003 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aic79xx.c#250 $ + */ + +#include "aic79xx_osm.h" +#include "aic79xx_inline.h" +#include "aicasm/aicasm_insformat.h" + +/***************************** Lookup Tables **********************************/ +static const char *const ahd_chip_names[] = +{ + "NONE", + "aic7901", + "aic7902", + "aic7901A" +}; + +/* + * Hardware error codes. + */ +struct ahd_hard_error_entry { + uint8_t errno; + const char *errmesg; +}; + +static const struct ahd_hard_error_entry ahd_hard_errors[] = { + { DSCTMOUT, "Discard Timer has timed out" }, + { ILLOPCODE, "Illegal Opcode in sequencer program" }, + { SQPARERR, "Sequencer Parity Error" }, + { DPARERR, "Data-path Parity Error" }, + { MPARERR, "Scratch or SCB Memory Parity Error" }, + { CIOPARERR, "CIOBUS Parity Error" }, +}; +static const u_int num_errors = ARRAY_SIZE(ahd_hard_errors); + +static const struct ahd_phase_table_entry ahd_phase_table[] = +{ + { P_DATAOUT, MSG_NOOP, "in Data-out phase" }, + { P_DATAIN, MSG_INITIATOR_DET_ERR, "in Data-in phase" }, + { P_DATAOUT_DT, MSG_NOOP, "in DT Data-out phase" }, + { P_DATAIN_DT, MSG_INITIATOR_DET_ERR, "in DT Data-in phase" }, + { P_COMMAND, MSG_NOOP, "in Command phase" }, + { P_MESGOUT, MSG_NOOP, "in Message-out phase" }, + { P_STATUS, MSG_INITIATOR_DET_ERR, "in Status phase" }, + { P_MESGIN, MSG_PARITY_ERROR, "in Message-in phase" }, + { P_BUSFREE, MSG_NOOP, "while idle" }, + { 0, MSG_NOOP, "in unknown phase" } +}; + +/* + * In most cases we only wish to itterate over real phases, so + * exclude the last element from the count. + */ +static const u_int num_phases = ARRAY_SIZE(ahd_phase_table) - 1; + +/* Our Sequencer Program */ +#include "aic79xx_seq.h" + +/**************************** Function Declarations ***************************/ +static void ahd_handle_transmission_error(struct ahd_softc *ahd); +static void ahd_handle_lqiphase_error(struct ahd_softc *ahd, + u_int lqistat1); +static int ahd_handle_pkt_busfree(struct ahd_softc *ahd, + u_int busfreetime); +static int ahd_handle_nonpkt_busfree(struct ahd_softc *ahd); +static void ahd_handle_proto_violation(struct ahd_softc *ahd); +static void ahd_force_renegotiation(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo); + +static struct ahd_tmode_tstate* + ahd_alloc_tstate(struct ahd_softc *ahd, + u_int scsi_id, char channel); +#ifdef AHD_TARGET_MODE +static void ahd_free_tstate(struct ahd_softc *ahd, + u_int scsi_id, char channel, int force); +#endif +static void ahd_devlimited_syncrate(struct ahd_softc *ahd, + struct ahd_initiator_tinfo *, + u_int *period, + u_int *ppr_options, + role_t role); +static void ahd_update_neg_table(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo, + struct ahd_transinfo *tinfo); +static void ahd_update_pending_scbs(struct ahd_softc *ahd); +static void ahd_fetch_devinfo(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo); +static void ahd_scb_devinfo(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo, + struct scb *scb); +static void ahd_setup_initiator_msgout(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo, + struct scb *scb); +static void ahd_build_transfer_msg(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo); +static void ahd_construct_sdtr(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo, + u_int period, u_int offset); +static void ahd_construct_wdtr(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo, + u_int bus_width); +static void ahd_construct_ppr(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo, + u_int period, u_int offset, + u_int bus_width, u_int ppr_options); +static void ahd_clear_msg_state(struct ahd_softc *ahd); +static void ahd_handle_message_phase(struct ahd_softc *ahd); +typedef enum { + AHDMSG_1B, + AHDMSG_2B, + AHDMSG_EXT +} ahd_msgtype; +static int ahd_sent_msg(struct ahd_softc *ahd, ahd_msgtype type, + u_int msgval, int full); +static int ahd_parse_msg(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo); +static int ahd_handle_msg_reject(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo); +static void ahd_handle_ign_wide_residue(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo); +static void ahd_reinitialize_dataptrs(struct ahd_softc *ahd); +static void ahd_handle_devreset(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo, + u_int lun, cam_status status, + char *message, int verbose_level); +#ifdef AHD_TARGET_MODE +static void ahd_setup_target_msgin(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo, + struct scb *scb); +#endif + +static u_int ahd_sglist_size(struct ahd_softc *ahd); +static u_int ahd_sglist_allocsize(struct ahd_softc *ahd); +static bus_dmamap_callback_t + ahd_dmamap_cb; +static void ahd_initialize_hscbs(struct ahd_softc *ahd); +static int ahd_init_scbdata(struct ahd_softc *ahd); +static void ahd_fini_scbdata(struct ahd_softc *ahd); +static void ahd_setup_iocell_workaround(struct ahd_softc *ahd); +static void ahd_iocell_first_selection(struct ahd_softc *ahd); +static void ahd_add_col_list(struct ahd_softc *ahd, + struct scb *scb, u_int col_idx); +static void ahd_rem_col_list(struct ahd_softc *ahd, + struct scb *scb); +static void ahd_chip_init(struct ahd_softc *ahd); +static void ahd_qinfifo_requeue(struct ahd_softc *ahd, + struct scb *prev_scb, + struct scb *scb); +static int ahd_qinfifo_count(struct ahd_softc *ahd); +static int ahd_search_scb_list(struct ahd_softc *ahd, int target, + char channel, int lun, u_int tag, + role_t role, uint32_t status, + ahd_search_action action, + u_int *list_head, u_int *list_tail, + u_int tid); +static void ahd_stitch_tid_list(struct ahd_softc *ahd, + u_int tid_prev, u_int tid_cur, + u_int tid_next); +static void ahd_add_scb_to_free_list(struct ahd_softc *ahd, + u_int scbid); +static u_int ahd_rem_wscb(struct ahd_softc *ahd, u_int scbid, + u_int prev, u_int next, u_int tid); +static void ahd_reset_current_bus(struct ahd_softc *ahd); +static void ahd_stat_timer(struct timer_list *t); +#ifdef AHD_DUMP_SEQ +static void ahd_dumpseq(struct ahd_softc *ahd); +#endif +static void ahd_loadseq(struct ahd_softc *ahd); +static int ahd_check_patch(struct ahd_softc *ahd, + const struct patch **start_patch, + u_int start_instr, u_int *skip_addr); +static u_int ahd_resolve_seqaddr(struct ahd_softc *ahd, + u_int address); +static void ahd_download_instr(struct ahd_softc *ahd, + u_int instrptr, uint8_t *dconsts); +static int ahd_probe_stack_size(struct ahd_softc *ahd); +static int ahd_scb_active_in_fifo(struct ahd_softc *ahd, + struct scb *scb); +static void ahd_run_data_fifo(struct ahd_softc *ahd, + struct scb *scb); + +#ifdef AHD_TARGET_MODE +static void ahd_queue_lstate_event(struct ahd_softc *ahd, + struct ahd_tmode_lstate *lstate, + u_int initiator_id, + u_int event_type, + u_int event_arg); +static void ahd_update_scsiid(struct ahd_softc *ahd, + u_int targid_mask); +static int ahd_handle_target_cmd(struct ahd_softc *ahd, + struct target_cmd *cmd); +#endif + +static int ahd_abort_scbs(struct ahd_softc *ahd, int target, + char channel, int lun, u_int tag, + role_t role, uint32_t status); +static void ahd_alloc_scbs(struct ahd_softc *ahd); +static void ahd_busy_tcl(struct ahd_softc *ahd, u_int tcl, + u_int scbid); +static void ahd_calc_residual(struct ahd_softc *ahd, + struct scb *scb); +static void ahd_clear_critical_section(struct ahd_softc *ahd); +static void ahd_clear_intstat(struct ahd_softc *ahd); +static void ahd_enable_coalescing(struct ahd_softc *ahd, + int enable); +static u_int ahd_find_busy_tcl(struct ahd_softc *ahd, u_int tcl); +static void ahd_freeze_devq(struct ahd_softc *ahd, + struct scb *scb); +static void ahd_handle_scb_status(struct ahd_softc *ahd, + struct scb *scb); +static const struct ahd_phase_table_entry* ahd_lookup_phase_entry(int phase); +static void ahd_shutdown(void *arg); +static void ahd_update_coalescing_values(struct ahd_softc *ahd, + u_int timer, + u_int maxcmds, + u_int mincmds); +static int ahd_verify_vpd_cksum(struct vpd_config *vpd); +static int ahd_wait_seeprom(struct ahd_softc *ahd); +static int ahd_match_scb(struct ahd_softc *ahd, struct scb *scb, + int target, char channel, int lun, + u_int tag, role_t role); + +static void ahd_reset_cmds_pending(struct ahd_softc *ahd); + +/*************************** Interrupt Services *******************************/ +static void ahd_run_qoutfifo(struct ahd_softc *ahd); +#ifdef AHD_TARGET_MODE +static void ahd_run_tqinfifo(struct ahd_softc *ahd, int paused); +#endif +static void ahd_handle_hwerrint(struct ahd_softc *ahd); +static void ahd_handle_seqint(struct ahd_softc *ahd, u_int intstat); +static void ahd_handle_scsiint(struct ahd_softc *ahd, + u_int intstat); + +/************************ Sequencer Execution Control *************************/ +void +ahd_set_modes(struct ahd_softc *ahd, ahd_mode src, ahd_mode dst) +{ + if (ahd->src_mode == src && ahd->dst_mode == dst) + return; +#ifdef AHD_DEBUG + if (ahd->src_mode == AHD_MODE_UNKNOWN + || ahd->dst_mode == AHD_MODE_UNKNOWN) + panic("Setting mode prior to saving it.\n"); + if ((ahd_debug & AHD_SHOW_MODEPTR) != 0) + printk("%s: Setting mode 0x%x\n", ahd_name(ahd), + ahd_build_mode_state(ahd, src, dst)); +#endif + ahd_outb(ahd, MODE_PTR, ahd_build_mode_state(ahd, src, dst)); + ahd->src_mode = src; + ahd->dst_mode = dst; +} + +static void +ahd_update_modes(struct ahd_softc *ahd) +{ + ahd_mode_state mode_ptr; + ahd_mode src; + ahd_mode dst; + + mode_ptr = ahd_inb(ahd, MODE_PTR); +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MODEPTR) != 0) + printk("Reading mode 0x%x\n", mode_ptr); +#endif + ahd_extract_mode_state(ahd, mode_ptr, &src, &dst); + ahd_known_modes(ahd, src, dst); +} + +static void +ahd_assert_modes(struct ahd_softc *ahd, ahd_mode srcmode, + ahd_mode dstmode, const char *file, int line) +{ +#ifdef AHD_DEBUG + if ((srcmode & AHD_MK_MSK(ahd->src_mode)) == 0 + || (dstmode & AHD_MK_MSK(ahd->dst_mode)) == 0) { + panic("%s:%s:%d: Mode assertion failed.\n", + ahd_name(ahd), file, line); + } +#endif +} + +#define AHD_ASSERT_MODES(ahd, source, dest) \ + ahd_assert_modes(ahd, source, dest, __FILE__, __LINE__); + +ahd_mode_state +ahd_save_modes(struct ahd_softc *ahd) +{ + if (ahd->src_mode == AHD_MODE_UNKNOWN + || ahd->dst_mode == AHD_MODE_UNKNOWN) + ahd_update_modes(ahd); + + return (ahd_build_mode_state(ahd, ahd->src_mode, ahd->dst_mode)); +} + +void +ahd_restore_modes(struct ahd_softc *ahd, ahd_mode_state state) +{ + ahd_mode src; + ahd_mode dst; + + ahd_extract_mode_state(ahd, state, &src, &dst); + ahd_set_modes(ahd, src, dst); +} + +/* + * Determine whether the sequencer has halted code execution. + * Returns non-zero status if the sequencer is stopped. + */ +int +ahd_is_paused(struct ahd_softc *ahd) +{ + return ((ahd_inb(ahd, HCNTRL) & PAUSE) != 0); +} + +/* + * Request that the sequencer stop and wait, indefinitely, for it + * to stop. The sequencer will only acknowledge that it is paused + * once it has reached an instruction boundary and PAUSEDIS is + * cleared in the SEQCTL register. The sequencer may use PAUSEDIS + * for critical sections. + */ +void +ahd_pause(struct ahd_softc *ahd) +{ + ahd_outb(ahd, HCNTRL, ahd->pause); + + /* + * Since the sequencer can disable pausing in a critical section, we + * must loop until it actually stops. + */ + while (ahd_is_paused(ahd) == 0) + ; +} + +/* + * Allow the sequencer to continue program execution. + * We check here to ensure that no additional interrupt + * sources that would cause the sequencer to halt have been + * asserted. If, for example, a SCSI bus reset is detected + * while we are fielding a different, pausing, interrupt type, + * we don't want to release the sequencer before going back + * into our interrupt handler and dealing with this new + * condition. + */ +void +ahd_unpause(struct ahd_softc *ahd) +{ + /* + * Automatically restore our modes to those saved + * prior to the first change of the mode. + */ + if (ahd->saved_src_mode != AHD_MODE_UNKNOWN + && ahd->saved_dst_mode != AHD_MODE_UNKNOWN) { + if ((ahd->flags & AHD_UPDATE_PEND_CMDS) != 0) + ahd_reset_cmds_pending(ahd); + ahd_set_modes(ahd, ahd->saved_src_mode, ahd->saved_dst_mode); + } + + if ((ahd_inb(ahd, INTSTAT) & ~CMDCMPLT) == 0) + ahd_outb(ahd, HCNTRL, ahd->unpause); + + ahd_known_modes(ahd, AHD_MODE_UNKNOWN, AHD_MODE_UNKNOWN); +} + +/*********************** Scatter Gather List Handling *************************/ +void * +ahd_sg_setup(struct ahd_softc *ahd, struct scb *scb, + void *sgptr, dma_addr_t addr, bus_size_t len, int last) +{ + scb->sg_count++; + if (sizeof(dma_addr_t) > 4 + && (ahd->flags & AHD_64BIT_ADDRESSING) != 0) { + struct ahd_dma64_seg *sg; + + sg = (struct ahd_dma64_seg *)sgptr; + sg->addr = ahd_htole64(addr); + sg->len = ahd_htole32(len | (last ? AHD_DMA_LAST_SEG : 0)); + return (sg + 1); + } else { + struct ahd_dma_seg *sg; + + sg = (struct ahd_dma_seg *)sgptr; + sg->addr = ahd_htole32(addr & 0xFFFFFFFF); + sg->len = ahd_htole32(len | ((addr >> 8) & 0x7F000000) + | (last ? AHD_DMA_LAST_SEG : 0)); + return (sg + 1); + } +} + +static void +ahd_setup_scb_common(struct ahd_softc *ahd, struct scb *scb) +{ + /* XXX Handle target mode SCBs. */ + scb->crc_retry_count = 0; + if ((scb->flags & SCB_PACKETIZED) != 0) { + /* XXX what about ACA?? It is type 4, but TAG_TYPE == 0x3. */ + scb->hscb->task_attribute = scb->hscb->control & SCB_TAG_TYPE; + } else { + if (ahd_get_transfer_length(scb) & 0x01) + scb->hscb->task_attribute = SCB_XFERLEN_ODD; + else + scb->hscb->task_attribute = 0; + } + + if (scb->hscb->cdb_len <= MAX_CDB_LEN_WITH_SENSE_ADDR + || (scb->hscb->cdb_len & SCB_CDB_LEN_PTR) != 0) + scb->hscb->shared_data.idata.cdb_plus_saddr.sense_addr = + ahd_htole32(scb->sense_busaddr); +} + +static void +ahd_setup_data_scb(struct ahd_softc *ahd, struct scb *scb) +{ + /* + * Copy the first SG into the "current" data ponter area. + */ + if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) { + struct ahd_dma64_seg *sg; + + sg = (struct ahd_dma64_seg *)scb->sg_list; + scb->hscb->dataptr = sg->addr; + scb->hscb->datacnt = sg->len; + } else { + struct ahd_dma_seg *sg; + uint32_t *dataptr_words; + + sg = (struct ahd_dma_seg *)scb->sg_list; + dataptr_words = (uint32_t*)&scb->hscb->dataptr; + dataptr_words[0] = sg->addr; + dataptr_words[1] = 0; + if ((ahd->flags & AHD_39BIT_ADDRESSING) != 0) { + uint64_t high_addr; + + high_addr = ahd_le32toh(sg->len) & 0x7F000000; + scb->hscb->dataptr |= ahd_htole64(high_addr << 8); + } + scb->hscb->datacnt = sg->len; + } + /* + * Note where to find the SG entries in bus space. + * We also set the full residual flag which the + * sequencer will clear as soon as a data transfer + * occurs. + */ + scb->hscb->sgptr = ahd_htole32(scb->sg_list_busaddr|SG_FULL_RESID); +} + +static void +ahd_setup_noxfer_scb(struct ahd_softc *ahd, struct scb *scb) +{ + scb->hscb->sgptr = ahd_htole32(SG_LIST_NULL); + scb->hscb->dataptr = 0; + scb->hscb->datacnt = 0; +} + +/************************** Memory mapping routines ***************************/ +static void * +ahd_sg_bus_to_virt(struct ahd_softc *ahd, struct scb *scb, uint32_t sg_busaddr) +{ + dma_addr_t sg_offset; + + /* sg_list_phys points to entry 1, not 0 */ + sg_offset = sg_busaddr - (scb->sg_list_busaddr - ahd_sg_size(ahd)); + return ((uint8_t *)scb->sg_list + sg_offset); +} + +static uint32_t +ahd_sg_virt_to_bus(struct ahd_softc *ahd, struct scb *scb, void *sg) +{ + dma_addr_t sg_offset; + + /* sg_list_phys points to entry 1, not 0 */ + sg_offset = ((uint8_t *)sg - (uint8_t *)scb->sg_list) + - ahd_sg_size(ahd); + + return (scb->sg_list_busaddr + sg_offset); +} + +static void +ahd_sync_scb(struct ahd_softc *ahd, struct scb *scb, int op) +{ + ahd_dmamap_sync(ahd, ahd->scb_data.hscb_dmat, + scb->hscb_map->dmamap, + /*offset*/(uint8_t*)scb->hscb - scb->hscb_map->vaddr, + /*len*/sizeof(*scb->hscb), op); +} + +void +ahd_sync_sglist(struct ahd_softc *ahd, struct scb *scb, int op) +{ + if (scb->sg_count == 0) + return; + + ahd_dmamap_sync(ahd, ahd->scb_data.sg_dmat, + scb->sg_map->dmamap, + /*offset*/scb->sg_list_busaddr - ahd_sg_size(ahd), + /*len*/ahd_sg_size(ahd) * scb->sg_count, op); +} + +static void +ahd_sync_sense(struct ahd_softc *ahd, struct scb *scb, int op) +{ + ahd_dmamap_sync(ahd, ahd->scb_data.sense_dmat, + scb->sense_map->dmamap, + /*offset*/scb->sense_busaddr, + /*len*/AHD_SENSE_BUFSIZE, op); +} + +#ifdef AHD_TARGET_MODE +static uint32_t +ahd_targetcmd_offset(struct ahd_softc *ahd, u_int index) +{ + return (((uint8_t *)&ahd->targetcmds[index]) + - (uint8_t *)ahd->qoutfifo); +} +#endif + +/*********************** Miscellaneous Support Functions ***********************/ +/* + * Return pointers to the transfer negotiation information + * for the specified our_id/remote_id pair. + */ +struct ahd_initiator_tinfo * +ahd_fetch_transinfo(struct ahd_softc *ahd, char channel, u_int our_id, + u_int remote_id, struct ahd_tmode_tstate **tstate) +{ + /* + * Transfer data structures are stored from the perspective + * of the target role. Since the parameters for a connection + * in the initiator role to a given target are the same as + * when the roles are reversed, we pretend we are the target. + */ + if (channel == 'B') + our_id += 8; + *tstate = ahd->enabled_targets[our_id]; + return (&(*tstate)->transinfo[remote_id]); +} + +uint16_t +ahd_inw(struct ahd_softc *ahd, u_int port) +{ + /* + * Read high byte first as some registers increment + * or have other side effects when the low byte is + * read. + */ + uint16_t r = ahd_inb(ahd, port+1) << 8; + return r | ahd_inb(ahd, port); +} + +void +ahd_outw(struct ahd_softc *ahd, u_int port, u_int value) +{ + /* + * Write low byte first to accommodate registers + * such as PRGMCNT where the order maters. + */ + ahd_outb(ahd, port, value & 0xFF); + ahd_outb(ahd, port+1, (value >> 8) & 0xFF); +} + +uint32_t +ahd_inl(struct ahd_softc *ahd, u_int port) +{ + return ((ahd_inb(ahd, port)) + | (ahd_inb(ahd, port+1) << 8) + | (ahd_inb(ahd, port+2) << 16) + | (ahd_inb(ahd, port+3) << 24)); +} + +void +ahd_outl(struct ahd_softc *ahd, u_int port, uint32_t value) +{ + ahd_outb(ahd, port, (value) & 0xFF); + ahd_outb(ahd, port+1, ((value) >> 8) & 0xFF); + ahd_outb(ahd, port+2, ((value) >> 16) & 0xFF); + ahd_outb(ahd, port+3, ((value) >> 24) & 0xFF); +} + +uint64_t +ahd_inq(struct ahd_softc *ahd, u_int port) +{ + return ((ahd_inb(ahd, port)) + | (ahd_inb(ahd, port+1) << 8) + | (ahd_inb(ahd, port+2) << 16) + | (ahd_inb(ahd, port+3) << 24) + | (((uint64_t)ahd_inb(ahd, port+4)) << 32) + | (((uint64_t)ahd_inb(ahd, port+5)) << 40) + | (((uint64_t)ahd_inb(ahd, port+6)) << 48) + | (((uint64_t)ahd_inb(ahd, port+7)) << 56)); +} + +void +ahd_outq(struct ahd_softc *ahd, u_int port, uint64_t value) +{ + ahd_outb(ahd, port, value & 0xFF); + ahd_outb(ahd, port+1, (value >> 8) & 0xFF); + ahd_outb(ahd, port+2, (value >> 16) & 0xFF); + ahd_outb(ahd, port+3, (value >> 24) & 0xFF); + ahd_outb(ahd, port+4, (value >> 32) & 0xFF); + ahd_outb(ahd, port+5, (value >> 40) & 0xFF); + ahd_outb(ahd, port+6, (value >> 48) & 0xFF); + ahd_outb(ahd, port+7, (value >> 56) & 0xFF); +} + +u_int +ahd_get_scbptr(struct ahd_softc *ahd) +{ + AHD_ASSERT_MODES(ahd, ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK), + ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK)); + return (ahd_inb(ahd, SCBPTR) | (ahd_inb(ahd, SCBPTR + 1) << 8)); +} + +void +ahd_set_scbptr(struct ahd_softc *ahd, u_int scbptr) +{ + AHD_ASSERT_MODES(ahd, ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK), + ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK)); + ahd_outb(ahd, SCBPTR, scbptr & 0xFF); + ahd_outb(ahd, SCBPTR+1, (scbptr >> 8) & 0xFF); +} + +#if 0 /* unused */ +static u_int +ahd_get_hnscb_qoff(struct ahd_softc *ahd) +{ + return (ahd_inw_atomic(ahd, HNSCB_QOFF)); +} +#endif + +static void +ahd_set_hnscb_qoff(struct ahd_softc *ahd, u_int value) +{ + ahd_outw_atomic(ahd, HNSCB_QOFF, value); +} + +#if 0 /* unused */ +static u_int +ahd_get_hescb_qoff(struct ahd_softc *ahd) +{ + return (ahd_inb(ahd, HESCB_QOFF)); +} +#endif + +static void +ahd_set_hescb_qoff(struct ahd_softc *ahd, u_int value) +{ + ahd_outb(ahd, HESCB_QOFF, value); +} + +static u_int +ahd_get_snscb_qoff(struct ahd_softc *ahd) +{ + u_int oldvalue; + + AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK); + oldvalue = ahd_inw(ahd, SNSCB_QOFF); + ahd_outw(ahd, SNSCB_QOFF, oldvalue); + return (oldvalue); +} + +static void +ahd_set_snscb_qoff(struct ahd_softc *ahd, u_int value) +{ + AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK); + ahd_outw(ahd, SNSCB_QOFF, value); +} + +#if 0 /* unused */ +static u_int +ahd_get_sescb_qoff(struct ahd_softc *ahd) +{ + AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK); + return (ahd_inb(ahd, SESCB_QOFF)); +} +#endif + +static void +ahd_set_sescb_qoff(struct ahd_softc *ahd, u_int value) +{ + AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK); + ahd_outb(ahd, SESCB_QOFF, value); +} + +#if 0 /* unused */ +static u_int +ahd_get_sdscb_qoff(struct ahd_softc *ahd) +{ + AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK); + return (ahd_inb(ahd, SDSCB_QOFF) | (ahd_inb(ahd, SDSCB_QOFF + 1) << 8)); +} +#endif + +static void +ahd_set_sdscb_qoff(struct ahd_softc *ahd, u_int value) +{ + AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK); + ahd_outb(ahd, SDSCB_QOFF, value & 0xFF); + ahd_outb(ahd, SDSCB_QOFF+1, (value >> 8) & 0xFF); +} + +u_int +ahd_inb_scbram(struct ahd_softc *ahd, u_int offset) +{ + u_int value; + + /* + * Workaround PCI-X Rev A. hardware bug. + * After a host read of SCB memory, the chip + * may become confused into thinking prefetch + * was required. This starts the discard timer + * running and can cause an unexpected discard + * timer interrupt. The work around is to read + * a normal register prior to the exhaustion of + * the discard timer. The mode pointer register + * has no side effects and so serves well for + * this purpose. + * + * Razor #528 + */ + value = ahd_inb(ahd, offset); + if ((ahd->bugs & AHD_PCIX_SCBRAM_RD_BUG) != 0) + ahd_inb(ahd, MODE_PTR); + return (value); +} + +u_int +ahd_inw_scbram(struct ahd_softc *ahd, u_int offset) +{ + return (ahd_inb_scbram(ahd, offset) + | (ahd_inb_scbram(ahd, offset+1) << 8)); +} + +static uint32_t +ahd_inl_scbram(struct ahd_softc *ahd, u_int offset) +{ + return (ahd_inw_scbram(ahd, offset) + | (ahd_inw_scbram(ahd, offset+2) << 16)); +} + +static uint64_t +ahd_inq_scbram(struct ahd_softc *ahd, u_int offset) +{ + return (ahd_inl_scbram(ahd, offset) + | ((uint64_t)ahd_inl_scbram(ahd, offset+4)) << 32); +} + +struct scb * +ahd_lookup_scb(struct ahd_softc *ahd, u_int tag) +{ + struct scb* scb; + + if (tag >= AHD_SCB_MAX) + return (NULL); + scb = ahd->scb_data.scbindex[tag]; + if (scb != NULL) + ahd_sync_scb(ahd, scb, + BUS_DMASYNC_POSTREAD|BUS_DMASYNC_POSTWRITE); + return (scb); +} + +static void +ahd_swap_with_next_hscb(struct ahd_softc *ahd, struct scb *scb) +{ + struct hardware_scb *q_hscb; + struct map_node *q_hscb_map; + uint32_t saved_hscb_busaddr; + + /* + * Our queuing method is a bit tricky. The card + * knows in advance which HSCB (by address) to download, + * and we can't disappoint it. To achieve this, the next + * HSCB to download is saved off in ahd->next_queued_hscb. + * When we are called to queue "an arbitrary scb", + * we copy the contents of the incoming HSCB to the one + * the sequencer knows about, swap HSCB pointers and + * finally assign the SCB to the tag indexed location + * in the scb_array. This makes sure that we can still + * locate the correct SCB by SCB_TAG. + */ + q_hscb = ahd->next_queued_hscb; + q_hscb_map = ahd->next_queued_hscb_map; + saved_hscb_busaddr = q_hscb->hscb_busaddr; + memcpy(q_hscb, scb->hscb, sizeof(*scb->hscb)); + q_hscb->hscb_busaddr = saved_hscb_busaddr; + q_hscb->next_hscb_busaddr = scb->hscb->hscb_busaddr; + + /* Now swap HSCB pointers. */ + ahd->next_queued_hscb = scb->hscb; + ahd->next_queued_hscb_map = scb->hscb_map; + scb->hscb = q_hscb; + scb->hscb_map = q_hscb_map; + + /* Now define the mapping from tag to SCB in the scbindex */ + ahd->scb_data.scbindex[SCB_GET_TAG(scb)] = scb; +} + +/* + * Tell the sequencer about a new transaction to execute. + */ +void +ahd_queue_scb(struct ahd_softc *ahd, struct scb *scb) +{ + ahd_swap_with_next_hscb(ahd, scb); + + if (SCBID_IS_NULL(SCB_GET_TAG(scb))) + panic("Attempt to queue invalid SCB tag %x\n", + SCB_GET_TAG(scb)); + + /* + * Keep a history of SCBs we've downloaded in the qinfifo. + */ + ahd->qinfifo[AHD_QIN_WRAP(ahd->qinfifonext)] = SCB_GET_TAG(scb); + ahd->qinfifonext++; + + if (scb->sg_count != 0) + ahd_setup_data_scb(ahd, scb); + else + ahd_setup_noxfer_scb(ahd, scb); + ahd_setup_scb_common(ahd, scb); + + /* + * Make sure our data is consistent from the + * perspective of the adapter. + */ + ahd_sync_scb(ahd, scb, BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_QUEUE) != 0) { + uint64_t host_dataptr; + + host_dataptr = ahd_le64toh(scb->hscb->dataptr); + printk("%s: Queueing SCB %d:0x%x bus addr 0x%x - 0x%x%x/0x%x\n", + ahd_name(ahd), + SCB_GET_TAG(scb), scb->hscb->scsiid, + ahd_le32toh(scb->hscb->hscb_busaddr), + (u_int)((host_dataptr >> 32) & 0xFFFFFFFF), + (u_int)(host_dataptr & 0xFFFFFFFF), + ahd_le32toh(scb->hscb->datacnt)); + } +#endif + /* Tell the adapter about the newly queued SCB */ + ahd_set_hnscb_qoff(ahd, ahd->qinfifonext); +} + +/************************** Interrupt Processing ******************************/ +static void +ahd_sync_qoutfifo(struct ahd_softc *ahd, int op) +{ + ahd_dmamap_sync(ahd, ahd->shared_data_dmat, ahd->shared_data_map.dmamap, + /*offset*/0, + /*len*/AHD_SCB_MAX * sizeof(struct ahd_completion), op); +} + +static void +ahd_sync_tqinfifo(struct ahd_softc *ahd, int op) +{ +#ifdef AHD_TARGET_MODE + if ((ahd->flags & AHD_TARGETROLE) != 0) { + ahd_dmamap_sync(ahd, ahd->shared_data_dmat, + ahd->shared_data_map.dmamap, + ahd_targetcmd_offset(ahd, 0), + sizeof(struct target_cmd) * AHD_TMODE_CMDS, + op); + } +#endif +} + +/* + * See if the firmware has posted any completed commands + * into our in-core command complete fifos. + */ +#define AHD_RUN_QOUTFIFO 0x1 +#define AHD_RUN_TQINFIFO 0x2 +static u_int +ahd_check_cmdcmpltqueues(struct ahd_softc *ahd) +{ + u_int retval; + + retval = 0; + ahd_dmamap_sync(ahd, ahd->shared_data_dmat, ahd->shared_data_map.dmamap, + /*offset*/ahd->qoutfifonext * sizeof(*ahd->qoutfifo), + /*len*/sizeof(*ahd->qoutfifo), BUS_DMASYNC_POSTREAD); + if (ahd->qoutfifo[ahd->qoutfifonext].valid_tag + == ahd->qoutfifonext_valid_tag) + retval |= AHD_RUN_QOUTFIFO; +#ifdef AHD_TARGET_MODE + if ((ahd->flags & AHD_TARGETROLE) != 0 + && (ahd->flags & AHD_TQINFIFO_BLOCKED) == 0) { + ahd_dmamap_sync(ahd, ahd->shared_data_dmat, + ahd->shared_data_map.dmamap, + ahd_targetcmd_offset(ahd, ahd->tqinfifofnext), + /*len*/sizeof(struct target_cmd), + BUS_DMASYNC_POSTREAD); + if (ahd->targetcmds[ahd->tqinfifonext].cmd_valid != 0) + retval |= AHD_RUN_TQINFIFO; + } +#endif + return (retval); +} + +/* + * Catch an interrupt from the adapter + */ +int +ahd_intr(struct ahd_softc *ahd) +{ + u_int intstat; + + if ((ahd->pause & INTEN) == 0) { + /* + * Our interrupt is not enabled on the chip + * and may be disabled for re-entrancy reasons, + * so just return. This is likely just a shared + * interrupt. + */ + return (0); + } + + /* + * Instead of directly reading the interrupt status register, + * infer the cause of the interrupt by checking our in-core + * completion queues. This avoids a costly PCI bus read in + * most cases. + */ + if ((ahd->flags & AHD_ALL_INTERRUPTS) == 0 + && (ahd_check_cmdcmpltqueues(ahd) != 0)) + intstat = CMDCMPLT; + else + intstat = ahd_inb(ahd, INTSTAT); + + if ((intstat & INT_PEND) == 0) + return (0); + + if (intstat & CMDCMPLT) { + ahd_outb(ahd, CLRINT, CLRCMDINT); + + /* + * Ensure that the chip sees that we've cleared + * this interrupt before we walk the output fifo. + * Otherwise, we may, due to posted bus writes, + * clear the interrupt after we finish the scan, + * and after the sequencer has added new entries + * and asserted the interrupt again. + */ + if ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0) { + if (ahd_is_paused(ahd)) { + /* + * Potentially lost SEQINT. + * If SEQINTCODE is non-zero, + * simulate the SEQINT. + */ + if (ahd_inb(ahd, SEQINTCODE) != NO_SEQINT) + intstat |= SEQINT; + } + } else { + ahd_flush_device_writes(ahd); + } + ahd_run_qoutfifo(ahd); + ahd->cmdcmplt_counts[ahd->cmdcmplt_bucket]++; + ahd->cmdcmplt_total++; +#ifdef AHD_TARGET_MODE + if ((ahd->flags & AHD_TARGETROLE) != 0) + ahd_run_tqinfifo(ahd, /*paused*/FALSE); +#endif + } + + /* + * Handle statuses that may invalidate our cached + * copy of INTSTAT separately. + */ + if (intstat == 0xFF && (ahd->features & AHD_REMOVABLE) != 0) { + /* Hot eject. Do nothing */ + } else if (intstat & HWERRINT) { + ahd_handle_hwerrint(ahd); + } else if ((intstat & (PCIINT|SPLTINT)) != 0) { + ahd->bus_intr(ahd); + } else { + + if ((intstat & SEQINT) != 0) + ahd_handle_seqint(ahd, intstat); + + if ((intstat & SCSIINT) != 0) + ahd_handle_scsiint(ahd, intstat); + } + return (1); +} + +/******************************** Private Inlines *****************************/ +static inline void +ahd_assert_atn(struct ahd_softc *ahd) +{ + ahd_outb(ahd, SCSISIGO, ATNO); +} + +/* + * Determine if the current connection has a packetized + * agreement. This does not necessarily mean that we + * are currently in a packetized transfer. We could + * just as easily be sending or receiving a message. + */ +static int +ahd_currently_packetized(struct ahd_softc *ahd) +{ + ahd_mode_state saved_modes; + int packetized; + + saved_modes = ahd_save_modes(ahd); + if ((ahd->bugs & AHD_PKTIZED_STATUS_BUG) != 0) { + /* + * The packetized bit refers to the last + * connection, not the current one. Check + * for non-zero LQISTATE instead. + */ + ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); + packetized = ahd_inb(ahd, LQISTATE) != 0; + } else { + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + packetized = ahd_inb(ahd, LQISTAT2) & PACKETIZED; + } + ahd_restore_modes(ahd, saved_modes); + return (packetized); +} + +static inline int +ahd_set_active_fifo(struct ahd_softc *ahd) +{ + u_int active_fifo; + + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + active_fifo = ahd_inb(ahd, DFFSTAT) & CURRFIFO; + switch (active_fifo) { + case 0: + case 1: + ahd_set_modes(ahd, active_fifo, active_fifo); + return (1); + default: + return (0); + } +} + +static inline void +ahd_unbusy_tcl(struct ahd_softc *ahd, u_int tcl) +{ + ahd_busy_tcl(ahd, tcl, SCB_LIST_NULL); +} + +/* + * Determine whether the sequencer reported a residual + * for this SCB/transaction. + */ +static inline void +ahd_update_residual(struct ahd_softc *ahd, struct scb *scb) +{ + uint32_t sgptr; + + sgptr = ahd_le32toh(scb->hscb->sgptr); + if ((sgptr & SG_STATUS_VALID) != 0) + ahd_calc_residual(ahd, scb); +} + +static inline void +ahd_complete_scb(struct ahd_softc *ahd, struct scb *scb) +{ + uint32_t sgptr; + + sgptr = ahd_le32toh(scb->hscb->sgptr); + if ((sgptr & SG_STATUS_VALID) != 0) + ahd_handle_scb_status(ahd, scb); + else + ahd_done(ahd, scb); +} + + +/************************* Sequencer Execution Control ************************/ +/* + * Restart the sequencer program from address zero + */ +static void +ahd_restart(struct ahd_softc *ahd) +{ + + ahd_pause(ahd); + + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + + /* No more pending messages */ + ahd_clear_msg_state(ahd); + ahd_outb(ahd, SCSISIGO, 0); /* De-assert BSY */ + ahd_outb(ahd, MSG_OUT, MSG_NOOP); /* No message to send */ + ahd_outb(ahd, SXFRCTL1, ahd_inb(ahd, SXFRCTL1) & ~BITBUCKET); + ahd_outb(ahd, SEQINTCTL, 0); + ahd_outb(ahd, LASTPHASE, P_BUSFREE); + ahd_outb(ahd, SEQ_FLAGS, 0); + ahd_outb(ahd, SAVED_SCSIID, 0xFF); + ahd_outb(ahd, SAVED_LUN, 0xFF); + + /* + * Ensure that the sequencer's idea of TQINPOS + * matches our own. The sequencer increments TQINPOS + * only after it sees a DMA complete and a reset could + * occur before the increment leaving the kernel to believe + * the command arrived but the sequencer to not. + */ + ahd_outb(ahd, TQINPOS, ahd->tqinfifonext); + + /* Always allow reselection */ + ahd_outb(ahd, SCSISEQ1, + ahd_inb(ahd, SCSISEQ_TEMPLATE) & (ENSELI|ENRSELI|ENAUTOATNP)); + ahd_set_modes(ahd, AHD_MODE_CCHAN, AHD_MODE_CCHAN); + + /* + * Clear any pending sequencer interrupt. It is no + * longer relevant since we're resetting the Program + * Counter. + */ + ahd_outb(ahd, CLRINT, CLRSEQINT); + + ahd_outb(ahd, SEQCTL0, FASTMODE|SEQRESET); + ahd_unpause(ahd); +} + +static void +ahd_clear_fifo(struct ahd_softc *ahd, u_int fifo) +{ + ahd_mode_state saved_modes; + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_FIFOS) != 0) + printk("%s: Clearing FIFO %d\n", ahd_name(ahd), fifo); +#endif + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, fifo, fifo); + ahd_outb(ahd, DFFSXFRCTL, RSTCHN|CLRSHCNT); + if ((ahd_inb(ahd, SG_STATE) & FETCH_INPROG) != 0) + ahd_outb(ahd, CCSGCTL, CCSGRESET); + ahd_outb(ahd, LONGJMP_ADDR + 1, INVALID_ADDR); + ahd_outb(ahd, SG_STATE, 0); + ahd_restore_modes(ahd, saved_modes); +} + +/************************* Input/Output Queues ********************************/ +/* + * Flush and completed commands that are sitting in the command + * complete queues down on the chip but have yet to be dma'ed back up. + */ +static void +ahd_flush_qoutfifo(struct ahd_softc *ahd) +{ + struct scb *scb; + ahd_mode_state saved_modes; + u_int saved_scbptr; + u_int ccscbctl; + u_int scbid; + u_int next_scbid; + + saved_modes = ahd_save_modes(ahd); + + /* + * Flush the good status FIFO for completed packetized commands. + */ + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + saved_scbptr = ahd_get_scbptr(ahd); + while ((ahd_inb(ahd, LQISTAT2) & LQIGSAVAIL) != 0) { + u_int fifo_mode; + u_int i; + + scbid = ahd_inw(ahd, GSFIFO); + scb = ahd_lookup_scb(ahd, scbid); + if (scb == NULL) { + printk("%s: Warning - GSFIFO SCB %d invalid\n", + ahd_name(ahd), scbid); + continue; + } + /* + * Determine if this transaction is still active in + * any FIFO. If it is, we must flush that FIFO to + * the host before completing the command. + */ + fifo_mode = 0; +rescan_fifos: + for (i = 0; i < 2; i++) { + /* Toggle to the other mode. */ + fifo_mode ^= 1; + ahd_set_modes(ahd, fifo_mode, fifo_mode); + + if (ahd_scb_active_in_fifo(ahd, scb) == 0) + continue; + + ahd_run_data_fifo(ahd, scb); + + /* + * Running this FIFO may cause a CFG4DATA for + * this same transaction to assert in the other + * FIFO or a new snapshot SAVEPTRS interrupt + * in this FIFO. Even running a FIFO may not + * clear the transaction if we are still waiting + * for data to drain to the host. We must loop + * until the transaction is not active in either + * FIFO just to be sure. Reset our loop counter + * so we will visit both FIFOs again before + * declaring this transaction finished. We + * also delay a bit so that status has a chance + * to change before we look at this FIFO again. + */ + ahd_delay(200); + goto rescan_fifos; + } + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + ahd_set_scbptr(ahd, scbid); + if ((ahd_inb_scbram(ahd, SCB_SGPTR) & SG_LIST_NULL) == 0 + && ((ahd_inb_scbram(ahd, SCB_SGPTR) & SG_FULL_RESID) != 0 + || (ahd_inb_scbram(ahd, SCB_RESIDUAL_SGPTR) + & SG_LIST_NULL) != 0)) { + u_int comp_head; + + /* + * The transfer completed with a residual. + * Place this SCB on the complete DMA list + * so that we update our in-core copy of the + * SCB before completing the command. + */ + ahd_outb(ahd, SCB_SCSI_STATUS, 0); + ahd_outb(ahd, SCB_SGPTR, + ahd_inb_scbram(ahd, SCB_SGPTR) + | SG_STATUS_VALID); + ahd_outw(ahd, SCB_TAG, scbid); + ahd_outw(ahd, SCB_NEXT_COMPLETE, SCB_LIST_NULL); + comp_head = ahd_inw(ahd, COMPLETE_DMA_SCB_HEAD); + if (SCBID_IS_NULL(comp_head)) { + ahd_outw(ahd, COMPLETE_DMA_SCB_HEAD, scbid); + ahd_outw(ahd, COMPLETE_DMA_SCB_TAIL, scbid); + } else { + u_int tail; + + tail = ahd_inw(ahd, COMPLETE_DMA_SCB_TAIL); + ahd_set_scbptr(ahd, tail); + ahd_outw(ahd, SCB_NEXT_COMPLETE, scbid); + ahd_outw(ahd, COMPLETE_DMA_SCB_TAIL, scbid); + ahd_set_scbptr(ahd, scbid); + } + } else + ahd_complete_scb(ahd, scb); + } + ahd_set_scbptr(ahd, saved_scbptr); + + /* + * Setup for command channel portion of flush. + */ + ahd_set_modes(ahd, AHD_MODE_CCHAN, AHD_MODE_CCHAN); + + /* + * Wait for any inprogress DMA to complete and clear DMA state + * if this is for an SCB in the qinfifo. + */ + while (((ccscbctl = ahd_inb(ahd, CCSCBCTL)) & (CCARREN|CCSCBEN)) != 0) { + + if ((ccscbctl & (CCSCBDIR|CCARREN)) == (CCSCBDIR|CCARREN)) { + if ((ccscbctl & ARRDONE) != 0) + break; + } else if ((ccscbctl & CCSCBDONE) != 0) + break; + ahd_delay(200); + } + /* + * We leave the sequencer to cleanup in the case of DMA's to + * update the qoutfifo. In all other cases (DMA's to the + * chip or a push of an SCB from the COMPLETE_DMA_SCB list), + * we disable the DMA engine so that the sequencer will not + * attempt to handle the DMA completion. + */ + if ((ccscbctl & CCSCBDIR) != 0 || (ccscbctl & ARRDONE) != 0) + ahd_outb(ahd, CCSCBCTL, ccscbctl & ~(CCARREN|CCSCBEN)); + + /* + * Complete any SCBs that just finished + * being DMA'ed into the qoutfifo. + */ + ahd_run_qoutfifo(ahd); + + saved_scbptr = ahd_get_scbptr(ahd); + /* + * Manually update/complete any completed SCBs that are waiting to be + * DMA'ed back up to the host. + */ + scbid = ahd_inw(ahd, COMPLETE_DMA_SCB_HEAD); + while (!SCBID_IS_NULL(scbid)) { + uint8_t *hscb_ptr; + u_int i; + + ahd_set_scbptr(ahd, scbid); + next_scbid = ahd_inw_scbram(ahd, SCB_NEXT_COMPLETE); + scb = ahd_lookup_scb(ahd, scbid); + if (scb == NULL) { + printk("%s: Warning - DMA-up and complete " + "SCB %d invalid\n", ahd_name(ahd), scbid); + continue; + } + hscb_ptr = (uint8_t *)scb->hscb; + for (i = 0; i < sizeof(struct hardware_scb); i++) + *hscb_ptr++ = ahd_inb_scbram(ahd, SCB_BASE + i); + + ahd_complete_scb(ahd, scb); + scbid = next_scbid; + } + ahd_outw(ahd, COMPLETE_DMA_SCB_HEAD, SCB_LIST_NULL); + ahd_outw(ahd, COMPLETE_DMA_SCB_TAIL, SCB_LIST_NULL); + + scbid = ahd_inw(ahd, COMPLETE_ON_QFREEZE_HEAD); + while (!SCBID_IS_NULL(scbid)) { + + ahd_set_scbptr(ahd, scbid); + next_scbid = ahd_inw_scbram(ahd, SCB_NEXT_COMPLETE); + scb = ahd_lookup_scb(ahd, scbid); + if (scb == NULL) { + printk("%s: Warning - Complete Qfrz SCB %d invalid\n", + ahd_name(ahd), scbid); + continue; + } + + ahd_complete_scb(ahd, scb); + scbid = next_scbid; + } + ahd_outw(ahd, COMPLETE_ON_QFREEZE_HEAD, SCB_LIST_NULL); + + scbid = ahd_inw(ahd, COMPLETE_SCB_HEAD); + while (!SCBID_IS_NULL(scbid)) { + + ahd_set_scbptr(ahd, scbid); + next_scbid = ahd_inw_scbram(ahd, SCB_NEXT_COMPLETE); + scb = ahd_lookup_scb(ahd, scbid); + if (scb == NULL) { + printk("%s: Warning - Complete SCB %d invalid\n", + ahd_name(ahd), scbid); + continue; + } + + ahd_complete_scb(ahd, scb); + scbid = next_scbid; + } + ahd_outw(ahd, COMPLETE_SCB_HEAD, SCB_LIST_NULL); + + /* + * Restore state. + */ + ahd_set_scbptr(ahd, saved_scbptr); + ahd_restore_modes(ahd, saved_modes); + ahd->flags |= AHD_UPDATE_PEND_CMDS; +} + +/* + * Determine if an SCB for a packetized transaction + * is active in a FIFO. + */ +static int +ahd_scb_active_in_fifo(struct ahd_softc *ahd, struct scb *scb) +{ + + /* + * The FIFO is only active for our transaction if + * the SCBPTR matches the SCB's ID and the firmware + * has installed a handler for the FIFO or we have + * a pending SAVEPTRS or CFG4DATA interrupt. + */ + if (ahd_get_scbptr(ahd) != SCB_GET_TAG(scb) + || ((ahd_inb(ahd, LONGJMP_ADDR+1) & INVALID_ADDR) != 0 + && (ahd_inb(ahd, SEQINTSRC) & (CFG4DATA|SAVEPTRS)) == 0)) + return (0); + + return (1); +} + +/* + * Run a data fifo to completion for a transaction we know + * has completed across the SCSI bus (good status has been + * received). We are already set to the correct FIFO mode + * on entry to this routine. + * + * This function attempts to operate exactly as the firmware + * would when running this FIFO. Care must be taken to update + * this routine any time the firmware's FIFO algorithm is + * changed. + */ +static void +ahd_run_data_fifo(struct ahd_softc *ahd, struct scb *scb) +{ + u_int seqintsrc; + + seqintsrc = ahd_inb(ahd, SEQINTSRC); + if ((seqintsrc & CFG4DATA) != 0) { + uint32_t datacnt; + uint32_t sgptr; + + /* + * Clear full residual flag. + */ + sgptr = ahd_inl_scbram(ahd, SCB_SGPTR) & ~SG_FULL_RESID; + ahd_outb(ahd, SCB_SGPTR, sgptr); + + /* + * Load datacnt and address. + */ + datacnt = ahd_inl_scbram(ahd, SCB_DATACNT); + if ((datacnt & AHD_DMA_LAST_SEG) != 0) { + sgptr |= LAST_SEG; + ahd_outb(ahd, SG_STATE, 0); + } else + ahd_outb(ahd, SG_STATE, LOADING_NEEDED); + ahd_outq(ahd, HADDR, ahd_inq_scbram(ahd, SCB_DATAPTR)); + ahd_outl(ahd, HCNT, datacnt & AHD_SG_LEN_MASK); + ahd_outb(ahd, SG_CACHE_PRE, sgptr); + ahd_outb(ahd, DFCNTRL, PRELOADEN|SCSIEN|HDMAEN); + + /* + * Initialize Residual Fields. + */ + ahd_outb(ahd, SCB_RESIDUAL_DATACNT+3, datacnt >> 24); + ahd_outl(ahd, SCB_RESIDUAL_SGPTR, sgptr & SG_PTR_MASK); + + /* + * Mark the SCB as having a FIFO in use. + */ + ahd_outb(ahd, SCB_FIFO_USE_COUNT, + ahd_inb_scbram(ahd, SCB_FIFO_USE_COUNT) + 1); + + /* + * Install a "fake" handler for this FIFO. + */ + ahd_outw(ahd, LONGJMP_ADDR, 0); + + /* + * Notify the hardware that we have satisfied + * this sequencer interrupt. + */ + ahd_outb(ahd, CLRSEQINTSRC, CLRCFG4DATA); + } else if ((seqintsrc & SAVEPTRS) != 0) { + uint32_t sgptr; + uint32_t resid; + + if ((ahd_inb(ahd, LONGJMP_ADDR+1)&INVALID_ADDR) != 0) { + /* + * Snapshot Save Pointers. All that + * is necessary to clear the snapshot + * is a CLRCHN. + */ + goto clrchn; + } + + /* + * Disable S/G fetch so the DMA engine + * is available to future users. + */ + if ((ahd_inb(ahd, SG_STATE) & FETCH_INPROG) != 0) + ahd_outb(ahd, CCSGCTL, 0); + ahd_outb(ahd, SG_STATE, 0); + + /* + * Flush the data FIFO. Strickly only + * necessary for Rev A parts. + */ + ahd_outb(ahd, DFCNTRL, ahd_inb(ahd, DFCNTRL) | FIFOFLUSH); + + /* + * Calculate residual. + */ + sgptr = ahd_inl_scbram(ahd, SCB_RESIDUAL_SGPTR); + resid = ahd_inl(ahd, SHCNT); + resid |= ahd_inb_scbram(ahd, SCB_RESIDUAL_DATACNT+3) << 24; + ahd_outl(ahd, SCB_RESIDUAL_DATACNT, resid); + if ((ahd_inb(ahd, SG_CACHE_SHADOW) & LAST_SEG) == 0) { + /* + * Must back up to the correct S/G element. + * Typically this just means resetting our + * low byte to the offset in the SG_CACHE, + * but if we wrapped, we have to correct + * the other bytes of the sgptr too. + */ + if ((ahd_inb(ahd, SG_CACHE_SHADOW) & 0x80) != 0 + && (sgptr & 0x80) == 0) + sgptr -= 0x100; + sgptr &= ~0xFF; + sgptr |= ahd_inb(ahd, SG_CACHE_SHADOW) + & SG_ADDR_MASK; + ahd_outl(ahd, SCB_RESIDUAL_SGPTR, sgptr); + ahd_outb(ahd, SCB_RESIDUAL_DATACNT + 3, 0); + } else if ((resid & AHD_SG_LEN_MASK) == 0) { + ahd_outb(ahd, SCB_RESIDUAL_SGPTR, + sgptr | SG_LIST_NULL); + } + /* + * Save Pointers. + */ + ahd_outq(ahd, SCB_DATAPTR, ahd_inq(ahd, SHADDR)); + ahd_outl(ahd, SCB_DATACNT, resid); + ahd_outl(ahd, SCB_SGPTR, sgptr); + ahd_outb(ahd, CLRSEQINTSRC, CLRSAVEPTRS); + ahd_outb(ahd, SEQIMODE, + ahd_inb(ahd, SEQIMODE) | ENSAVEPTRS); + /* + * If the data is to the SCSI bus, we are + * done, otherwise wait for FIFOEMP. + */ + if ((ahd_inb(ahd, DFCNTRL) & DIRECTION) != 0) + goto clrchn; + } else if ((ahd_inb(ahd, SG_STATE) & LOADING_NEEDED) != 0) { + uint32_t sgptr; + uint64_t data_addr; + uint32_t data_len; + u_int dfcntrl; + + /* + * Disable S/G fetch so the DMA engine + * is available to future users. We won't + * be using the DMA engine to load segments. + */ + if ((ahd_inb(ahd, SG_STATE) & FETCH_INPROG) != 0) { + ahd_outb(ahd, CCSGCTL, 0); + ahd_outb(ahd, SG_STATE, LOADING_NEEDED); + } + + /* + * Wait for the DMA engine to notice that the + * host transfer is enabled and that there is + * space in the S/G FIFO for new segments before + * loading more segments. + */ + if ((ahd_inb(ahd, DFSTATUS) & PRELOAD_AVAIL) != 0 + && (ahd_inb(ahd, DFCNTRL) & HDMAENACK) != 0) { + + /* + * Determine the offset of the next S/G + * element to load. + */ + sgptr = ahd_inl_scbram(ahd, SCB_RESIDUAL_SGPTR); + sgptr &= SG_PTR_MASK; + if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) { + struct ahd_dma64_seg *sg; + + sg = ahd_sg_bus_to_virt(ahd, scb, sgptr); + data_addr = sg->addr; + data_len = sg->len; + sgptr += sizeof(*sg); + } else { + struct ahd_dma_seg *sg; + + sg = ahd_sg_bus_to_virt(ahd, scb, sgptr); + data_addr = sg->len & AHD_SG_HIGH_ADDR_MASK; + data_addr <<= 8; + data_addr |= sg->addr; + data_len = sg->len; + sgptr += sizeof(*sg); + } + + /* + * Update residual information. + */ + ahd_outb(ahd, SCB_RESIDUAL_DATACNT+3, data_len >> 24); + ahd_outl(ahd, SCB_RESIDUAL_SGPTR, sgptr); + + /* + * Load the S/G. + */ + if (data_len & AHD_DMA_LAST_SEG) { + sgptr |= LAST_SEG; + ahd_outb(ahd, SG_STATE, 0); + } + ahd_outq(ahd, HADDR, data_addr); + ahd_outl(ahd, HCNT, data_len & AHD_SG_LEN_MASK); + ahd_outb(ahd, SG_CACHE_PRE, sgptr & 0xFF); + + /* + * Advertise the segment to the hardware. + */ + dfcntrl = ahd_inb(ahd, DFCNTRL)|PRELOADEN|HDMAEN; + if ((ahd->features & AHD_NEW_DFCNTRL_OPTS) != 0) { + /* + * Use SCSIENWRDIS so that SCSIEN + * is never modified by this + * operation. + */ + dfcntrl |= SCSIENWRDIS; + } + ahd_outb(ahd, DFCNTRL, dfcntrl); + } + } else if ((ahd_inb(ahd, SG_CACHE_SHADOW) & LAST_SEG_DONE) != 0) { + + /* + * Transfer completed to the end of SG list + * and has flushed to the host. + */ + ahd_outb(ahd, SCB_SGPTR, + ahd_inb_scbram(ahd, SCB_SGPTR) | SG_LIST_NULL); + goto clrchn; + } else if ((ahd_inb(ahd, DFSTATUS) & FIFOEMP) != 0) { +clrchn: + /* + * Clear any handler for this FIFO, decrement + * the FIFO use count for the SCB, and release + * the FIFO. + */ + ahd_outb(ahd, LONGJMP_ADDR + 1, INVALID_ADDR); + ahd_outb(ahd, SCB_FIFO_USE_COUNT, + ahd_inb_scbram(ahd, SCB_FIFO_USE_COUNT) - 1); + ahd_outb(ahd, DFFSXFRCTL, CLRCHN); + } +} + +/* + * Look for entries in the QoutFIFO that have completed. + * The valid_tag completion field indicates the validity + * of the entry - the valid value toggles each time through + * the queue. We use the sg_status field in the completion + * entry to avoid referencing the hscb if the completion + * occurred with no errors and no residual. sg_status is + * a copy of the first byte (little endian) of the sgptr + * hscb field. + */ +static void +ahd_run_qoutfifo(struct ahd_softc *ahd) +{ + struct ahd_completion *completion; + struct scb *scb; + u_int scb_index; + + if ((ahd->flags & AHD_RUNNING_QOUTFIFO) != 0) + panic("ahd_run_qoutfifo recursion"); + ahd->flags |= AHD_RUNNING_QOUTFIFO; + ahd_sync_qoutfifo(ahd, BUS_DMASYNC_POSTREAD); + for (;;) { + completion = &ahd->qoutfifo[ahd->qoutfifonext]; + + if (completion->valid_tag != ahd->qoutfifonext_valid_tag) + break; + + scb_index = ahd_le16toh(completion->tag); + scb = ahd_lookup_scb(ahd, scb_index); + if (scb == NULL) { + printk("%s: WARNING no command for scb %d " + "(cmdcmplt)\nQOUTPOS = %d\n", + ahd_name(ahd), scb_index, + ahd->qoutfifonext); + ahd_dump_card_state(ahd); + } else if ((completion->sg_status & SG_STATUS_VALID) != 0) { + ahd_handle_scb_status(ahd, scb); + } else { + ahd_done(ahd, scb); + } + + ahd->qoutfifonext = (ahd->qoutfifonext+1) & (AHD_QOUT_SIZE-1); + if (ahd->qoutfifonext == 0) + ahd->qoutfifonext_valid_tag ^= QOUTFIFO_ENTRY_VALID; + } + ahd->flags &= ~AHD_RUNNING_QOUTFIFO; +} + +/************************* Interrupt Handling *********************************/ +static void +ahd_handle_hwerrint(struct ahd_softc *ahd) +{ + /* + * Some catastrophic hardware error has occurred. + * Print it for the user and disable the controller. + */ + int i; + int error; + + error = ahd_inb(ahd, ERROR); + for (i = 0; i < num_errors; i++) { + if ((error & ahd_hard_errors[i].errno) != 0) + printk("%s: hwerrint, %s\n", + ahd_name(ahd), ahd_hard_errors[i].errmesg); + } + + ahd_dump_card_state(ahd); + panic("BRKADRINT"); + + /* Tell everyone that this HBA is no longer available */ + ahd_abort_scbs(ahd, CAM_TARGET_WILDCARD, ALL_CHANNELS, + CAM_LUN_WILDCARD, SCB_LIST_NULL, ROLE_UNKNOWN, + CAM_NO_HBA); + + /* Tell the system that this controller has gone away. */ + ahd_free(ahd); +} + +#ifdef AHD_DEBUG +static void +ahd_dump_sglist(struct scb *scb) +{ + int i; + + if (scb->sg_count > 0) { + if ((scb->ahd_softc->flags & AHD_64BIT_ADDRESSING) != 0) { + struct ahd_dma64_seg *sg_list; + + sg_list = (struct ahd_dma64_seg*)scb->sg_list; + for (i = 0; i < scb->sg_count; i++) { + uint64_t addr; + + addr = ahd_le64toh(sg_list[i].addr); + printk("sg[%d] - Addr 0x%x%x : Length %d%s\n", + i, + (uint32_t)((addr >> 32) & 0xFFFFFFFF), + (uint32_t)(addr & 0xFFFFFFFF), + sg_list[i].len & AHD_SG_LEN_MASK, + (sg_list[i].len & AHD_DMA_LAST_SEG) + ? " Last" : ""); + } + } else { + struct ahd_dma_seg *sg_list; + + sg_list = (struct ahd_dma_seg*)scb->sg_list; + for (i = 0; i < scb->sg_count; i++) { + uint32_t len; + + len = ahd_le32toh(sg_list[i].len); + printk("sg[%d] - Addr 0x%x%x : Length %d%s\n", + i, + (len & AHD_SG_HIGH_ADDR_MASK) >> 24, + ahd_le32toh(sg_list[i].addr), + len & AHD_SG_LEN_MASK, + len & AHD_DMA_LAST_SEG ? " Last" : ""); + } + } + } +} +#endif /* AHD_DEBUG */ + +static void +ahd_handle_seqint(struct ahd_softc *ahd, u_int intstat) +{ + u_int seqintcode; + + /* + * Save the sequencer interrupt code and clear the SEQINT + * bit. We will unpause the sequencer, if appropriate, + * after servicing the request. + */ + seqintcode = ahd_inb(ahd, SEQINTCODE); + ahd_outb(ahd, CLRINT, CLRSEQINT); + if ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0) { + /* + * Unpause the sequencer and let it clear + * SEQINT by writing NO_SEQINT to it. This + * will cause the sequencer to be paused again, + * which is the expected state of this routine. + */ + ahd_unpause(ahd); + while (!ahd_is_paused(ahd)) + ; + ahd_outb(ahd, CLRINT, CLRSEQINT); + } + ahd_update_modes(ahd); +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MISC) != 0) + printk("%s: Handle Seqint Called for code %d\n", + ahd_name(ahd), seqintcode); +#endif + switch (seqintcode) { + case ENTERING_NONPACK: + { + struct scb *scb; + u_int scbid; + + AHD_ASSERT_MODES(ahd, ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK), + ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK)); + scbid = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scbid); + if (scb == NULL) { + /* + * Somehow need to know if this + * is from a selection or reselection. + * From that, we can determine target + * ID so we at least have an I_T nexus. + */ + } else { + ahd_outb(ahd, SAVED_SCSIID, scb->hscb->scsiid); + ahd_outb(ahd, SAVED_LUN, scb->hscb->lun); + ahd_outb(ahd, SEQ_FLAGS, 0x0); + } + if ((ahd_inb(ahd, LQISTAT2) & LQIPHASE_OUTPKT) != 0 + && (ahd_inb(ahd, SCSISIGO) & ATNO) != 0) { + /* + * Phase change after read stream with + * CRC error with P0 asserted on last + * packet. + */ +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_RECOVERY) != 0) + printk("%s: Assuming LQIPHASE_NLQ with " + "P0 assertion\n", ahd_name(ahd)); +#endif + } +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_RECOVERY) != 0) + printk("%s: Entering NONPACK\n", ahd_name(ahd)); +#endif + break; + } + case INVALID_SEQINT: + printk("%s: Invalid Sequencer interrupt occurred, " + "resetting channel.\n", + ahd_name(ahd)); +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_RECOVERY) != 0) + ahd_dump_card_state(ahd); +#endif + ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE); + break; + case STATUS_OVERRUN: + { + struct scb *scb; + u_int scbid; + + scbid = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scbid); + if (scb != NULL) + ahd_print_path(ahd, scb); + else + printk("%s: ", ahd_name(ahd)); + printk("SCB %d Packetized Status Overrun", scbid); + ahd_dump_card_state(ahd); + ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE); + break; + } + case CFG4ISTAT_INTR: + { + struct scb *scb; + u_int scbid; + + scbid = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scbid); + if (scb == NULL) { + ahd_dump_card_state(ahd); + printk("CFG4ISTAT: Free SCB %d referenced", scbid); + panic("For safety"); + } + ahd_outq(ahd, HADDR, scb->sense_busaddr); + ahd_outw(ahd, HCNT, AHD_SENSE_BUFSIZE); + ahd_outb(ahd, HCNT + 2, 0); + ahd_outb(ahd, SG_CACHE_PRE, SG_LAST_SEG); + ahd_outb(ahd, DFCNTRL, PRELOADEN|SCSIEN|HDMAEN); + break; + } + case ILLEGAL_PHASE: + { + u_int bus_phase; + + bus_phase = ahd_inb(ahd, SCSISIGI) & PHASE_MASK; + printk("%s: ILLEGAL_PHASE 0x%x\n", + ahd_name(ahd), bus_phase); + + switch (bus_phase) { + case P_DATAOUT: + case P_DATAIN: + case P_DATAOUT_DT: + case P_DATAIN_DT: + case P_MESGOUT: + case P_STATUS: + case P_MESGIN: + ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE); + printk("%s: Issued Bus Reset.\n", ahd_name(ahd)); + break; + case P_COMMAND: + { + struct ahd_devinfo devinfo; + struct scb *scb; + u_int scbid; + + /* + * If a target takes us into the command phase + * assume that it has been externally reset and + * has thus lost our previous packetized negotiation + * agreement. Since we have not sent an identify + * message and may not have fully qualified the + * connection, we change our command to TUR, assert + * ATN and ABORT the task when we go to message in + * phase. The OSM will see the REQUEUE_REQUEST + * status and retry the command. + */ + scbid = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scbid); + if (scb == NULL) { + printk("Invalid phase with no valid SCB. " + "Resetting bus.\n"); + ahd_reset_channel(ahd, 'A', + /*Initiate Reset*/TRUE); + break; + } + ahd_compile_devinfo(&devinfo, SCB_GET_OUR_ID(scb), + SCB_GET_TARGET(ahd, scb), + SCB_GET_LUN(scb), + SCB_GET_CHANNEL(ahd, scb), + ROLE_INITIATOR); + ahd_set_width(ahd, &devinfo, MSG_EXT_WDTR_BUS_8_BIT, + AHD_TRANS_ACTIVE, /*paused*/TRUE); + ahd_set_syncrate(ahd, &devinfo, /*period*/0, + /*offset*/0, /*ppr_options*/0, + AHD_TRANS_ACTIVE, /*paused*/TRUE); + /* Hand-craft TUR command */ + ahd_outb(ahd, SCB_CDB_STORE, 0); + ahd_outb(ahd, SCB_CDB_STORE+1, 0); + ahd_outb(ahd, SCB_CDB_STORE+2, 0); + ahd_outb(ahd, SCB_CDB_STORE+3, 0); + ahd_outb(ahd, SCB_CDB_STORE+4, 0); + ahd_outb(ahd, SCB_CDB_STORE+5, 0); + ahd_outb(ahd, SCB_CDB_LEN, 6); + scb->hscb->control &= ~(TAG_ENB|SCB_TAG_TYPE); + scb->hscb->control |= MK_MESSAGE; + ahd_outb(ahd, SCB_CONTROL, scb->hscb->control); + ahd_outb(ahd, MSG_OUT, HOST_MSG); + ahd_outb(ahd, SAVED_SCSIID, scb->hscb->scsiid); + /* + * The lun is 0, regardless of the SCB's lun + * as we have not sent an identify message. + */ + ahd_outb(ahd, SAVED_LUN, 0); + ahd_outb(ahd, SEQ_FLAGS, 0); + ahd_assert_atn(ahd); + scb->flags &= ~SCB_PACKETIZED; + scb->flags |= SCB_ABORT|SCB_EXTERNAL_RESET; + ahd_freeze_devq(ahd, scb); + ahd_set_transaction_status(scb, CAM_REQUEUE_REQ); + ahd_freeze_scb(scb); + + /* Notify XPT */ + ahd_send_async(ahd, devinfo.channel, devinfo.target, + CAM_LUN_WILDCARD, AC_SENT_BDR); + + /* + * Allow the sequencer to continue with + * non-pack processing. + */ + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + ahd_outb(ahd, CLRLQOINT1, CLRLQOPHACHGINPKT); + if ((ahd->bugs & AHD_CLRLQO_AUTOCLR_BUG) != 0) { + ahd_outb(ahd, CLRLQOINT1, 0); + } +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_RECOVERY) != 0) { + ahd_print_path(ahd, scb); + printk("Unexpected command phase from " + "packetized target\n"); + } +#endif + break; + } + } + break; + } + case CFG4OVERRUN: + { + struct scb *scb; + u_int scb_index; + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_RECOVERY) != 0) { + printk("%s: CFG4OVERRUN mode = %x\n", ahd_name(ahd), + ahd_inb(ahd, MODE_PTR)); + } +#endif + scb_index = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scb_index); + if (scb == NULL) { + /* + * Attempt to transfer to an SCB that is + * not outstanding. + */ + ahd_assert_atn(ahd); + ahd_outb(ahd, MSG_OUT, HOST_MSG); + ahd->msgout_buf[0] = MSG_ABORT_TASK; + ahd->msgout_len = 1; + ahd->msgout_index = 0; + ahd->msg_type = MSG_TYPE_INITIATOR_MSGOUT; + /* + * Clear status received flag to prevent any + * attempt to complete this bogus SCB. + */ + ahd_outb(ahd, SCB_CONTROL, + ahd_inb_scbram(ahd, SCB_CONTROL) + & ~STATUS_RCVD); + } + break; + } + case DUMP_CARD_STATE: + { + ahd_dump_card_state(ahd); + break; + } + case PDATA_REINIT: + { +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_RECOVERY) != 0) { + printk("%s: PDATA_REINIT - DFCNTRL = 0x%x " + "SG_CACHE_SHADOW = 0x%x\n", + ahd_name(ahd), ahd_inb(ahd, DFCNTRL), + ahd_inb(ahd, SG_CACHE_SHADOW)); + } +#endif + ahd_reinitialize_dataptrs(ahd); + break; + } + case HOST_MSG_LOOP: + { + struct ahd_devinfo devinfo; + + /* + * The sequencer has encountered a message phase + * that requires host assistance for completion. + * While handling the message phase(s), we will be + * notified by the sequencer after each byte is + * transferred so we can track bus phase changes. + * + * If this is the first time we've seen a HOST_MSG_LOOP + * interrupt, initialize the state of the host message + * loop. + */ + ahd_fetch_devinfo(ahd, &devinfo); + if (ahd->msg_type == MSG_TYPE_NONE) { + struct scb *scb; + u_int scb_index; + u_int bus_phase; + + bus_phase = ahd_inb(ahd, SCSISIGI) & PHASE_MASK; + if (bus_phase != P_MESGIN + && bus_phase != P_MESGOUT) { + printk("ahd_intr: HOST_MSG_LOOP bad " + "phase 0x%x\n", bus_phase); + /* + * Probably transitioned to bus free before + * we got here. Just punt the message. + */ + ahd_dump_card_state(ahd); + ahd_clear_intstat(ahd); + ahd_restart(ahd); + return; + } + + scb_index = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scb_index); + if (devinfo.role == ROLE_INITIATOR) { + if (bus_phase == P_MESGOUT) + ahd_setup_initiator_msgout(ahd, + &devinfo, + scb); + else { + ahd->msg_type = + MSG_TYPE_INITIATOR_MSGIN; + ahd->msgin_index = 0; + } + } +#ifdef AHD_TARGET_MODE + else { + if (bus_phase == P_MESGOUT) { + ahd->msg_type = + MSG_TYPE_TARGET_MSGOUT; + ahd->msgin_index = 0; + } + else + ahd_setup_target_msgin(ahd, + &devinfo, + scb); + } +#endif + } + + ahd_handle_message_phase(ahd); + break; + } + case NO_MATCH: + { + /* Ensure we don't leave the selection hardware on */ + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + ahd_outb(ahd, SCSISEQ0, ahd_inb(ahd, SCSISEQ0) & ~ENSELO); + + printk("%s:%c:%d: no active SCB for reconnecting " + "target - issuing BUS DEVICE RESET\n", + ahd_name(ahd), 'A', ahd_inb(ahd, SELID) >> 4); + printk("SAVED_SCSIID == 0x%x, SAVED_LUN == 0x%x, " + "REG0 == 0x%x ACCUM = 0x%x\n", + ahd_inb(ahd, SAVED_SCSIID), ahd_inb(ahd, SAVED_LUN), + ahd_inw(ahd, REG0), ahd_inb(ahd, ACCUM)); + printk("SEQ_FLAGS == 0x%x, SCBPTR == 0x%x, BTT == 0x%x, " + "SINDEX == 0x%x\n", + ahd_inb(ahd, SEQ_FLAGS), ahd_get_scbptr(ahd), + ahd_find_busy_tcl(ahd, + BUILD_TCL(ahd_inb(ahd, SAVED_SCSIID), + ahd_inb(ahd, SAVED_LUN))), + ahd_inw(ahd, SINDEX)); + printk("SELID == 0x%x, SCB_SCSIID == 0x%x, SCB_LUN == 0x%x, " + "SCB_CONTROL == 0x%x\n", + ahd_inb(ahd, SELID), ahd_inb_scbram(ahd, SCB_SCSIID), + ahd_inb_scbram(ahd, SCB_LUN), + ahd_inb_scbram(ahd, SCB_CONTROL)); + printk("SCSIBUS[0] == 0x%x, SCSISIGI == 0x%x\n", + ahd_inb(ahd, SCSIBUS), ahd_inb(ahd, SCSISIGI)); + printk("SXFRCTL0 == 0x%x\n", ahd_inb(ahd, SXFRCTL0)); + printk("SEQCTL0 == 0x%x\n", ahd_inb(ahd, SEQCTL0)); + ahd_dump_card_state(ahd); + ahd->msgout_buf[0] = MSG_BUS_DEV_RESET; + ahd->msgout_len = 1; + ahd->msgout_index = 0; + ahd->msg_type = MSG_TYPE_INITIATOR_MSGOUT; + ahd_outb(ahd, MSG_OUT, HOST_MSG); + ahd_assert_atn(ahd); + break; + } + case PROTO_VIOLATION: + { + ahd_handle_proto_violation(ahd); + break; + } + case IGN_WIDE_RES: + { + struct ahd_devinfo devinfo; + + ahd_fetch_devinfo(ahd, &devinfo); + ahd_handle_ign_wide_residue(ahd, &devinfo); + break; + } + case BAD_PHASE: + { + u_int lastphase; + + lastphase = ahd_inb(ahd, LASTPHASE); + printk("%s:%c:%d: unknown scsi bus phase %x, " + "lastphase = 0x%x. Attempting to continue\n", + ahd_name(ahd), 'A', + SCSIID_TARGET(ahd, ahd_inb(ahd, SAVED_SCSIID)), + lastphase, ahd_inb(ahd, SCSISIGI)); + break; + } + case MISSED_BUSFREE: + { + u_int lastphase; + + lastphase = ahd_inb(ahd, LASTPHASE); + printk("%s:%c:%d: Missed busfree. " + "Lastphase = 0x%x, Curphase = 0x%x\n", + ahd_name(ahd), 'A', + SCSIID_TARGET(ahd, ahd_inb(ahd, SAVED_SCSIID)), + lastphase, ahd_inb(ahd, SCSISIGI)); + ahd_restart(ahd); + return; + } + case DATA_OVERRUN: + { + /* + * When the sequencer detects an overrun, it + * places the controller in "BITBUCKET" mode + * and allows the target to complete its transfer. + * Unfortunately, none of the counters get updated + * when the controller is in this mode, so we have + * no way of knowing how large the overrun was. + */ + struct scb *scb; + u_int scbindex; +#ifdef AHD_DEBUG + u_int lastphase; +#endif + + scbindex = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scbindex); +#ifdef AHD_DEBUG + lastphase = ahd_inb(ahd, LASTPHASE); + if ((ahd_debug & AHD_SHOW_RECOVERY) != 0) { + ahd_print_path(ahd, scb); + printk("data overrun detected %s. Tag == 0x%x.\n", + ahd_lookup_phase_entry(lastphase)->phasemsg, + SCB_GET_TAG(scb)); + ahd_print_path(ahd, scb); + printk("%s seen Data Phase. Length = %ld. " + "NumSGs = %d.\n", + ahd_inb(ahd, SEQ_FLAGS) & DPHASE + ? "Have" : "Haven't", + ahd_get_transfer_length(scb), scb->sg_count); + ahd_dump_sglist(scb); + } +#endif + + /* + * Set this and it will take effect when the + * target does a command complete. + */ + ahd_freeze_devq(ahd, scb); + ahd_set_transaction_status(scb, CAM_DATA_RUN_ERR); + ahd_freeze_scb(scb); + break; + } + case MKMSG_FAILED: + { + struct ahd_devinfo devinfo; + struct scb *scb; + u_int scbid; + + ahd_fetch_devinfo(ahd, &devinfo); + printk("%s:%c:%d:%d: Attempt to issue message failed\n", + ahd_name(ahd), devinfo.channel, devinfo.target, + devinfo.lun); + scbid = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scbid); + if (scb != NULL + && (scb->flags & SCB_RECOVERY_SCB) != 0) + /* + * Ensure that we didn't put a second instance of this + * SCB into the QINFIFO. + */ + ahd_search_qinfifo(ahd, SCB_GET_TARGET(ahd, scb), + SCB_GET_CHANNEL(ahd, scb), + SCB_GET_LUN(scb), SCB_GET_TAG(scb), + ROLE_INITIATOR, /*status*/0, + SEARCH_REMOVE); + ahd_outb(ahd, SCB_CONTROL, + ahd_inb_scbram(ahd, SCB_CONTROL) & ~MK_MESSAGE); + break; + } + case TASKMGMT_FUNC_COMPLETE: + { + u_int scbid; + struct scb *scb; + + scbid = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scbid); + if (scb != NULL) { + u_int lun; + u_int tag; + cam_status error; + + ahd_print_path(ahd, scb); + printk("Task Management Func 0x%x Complete\n", + scb->hscb->task_management); + lun = CAM_LUN_WILDCARD; + tag = SCB_LIST_NULL; + + switch (scb->hscb->task_management) { + case SIU_TASKMGMT_ABORT_TASK: + tag = SCB_GET_TAG(scb); + fallthrough; + case SIU_TASKMGMT_ABORT_TASK_SET: + case SIU_TASKMGMT_CLEAR_TASK_SET: + lun = scb->hscb->lun; + error = CAM_REQ_ABORTED; + ahd_abort_scbs(ahd, SCB_GET_TARGET(ahd, scb), + 'A', lun, tag, ROLE_INITIATOR, + error); + break; + case SIU_TASKMGMT_LUN_RESET: + lun = scb->hscb->lun; + fallthrough; + case SIU_TASKMGMT_TARGET_RESET: + { + struct ahd_devinfo devinfo; + + ahd_scb_devinfo(ahd, &devinfo, scb); + error = CAM_BDR_SENT; + ahd_handle_devreset(ahd, &devinfo, lun, + CAM_BDR_SENT, + lun != CAM_LUN_WILDCARD + ? "Lun Reset" + : "Target Reset", + /*verbose_level*/0); + break; + } + default: + panic("Unexpected TaskMgmt Func\n"); + break; + } + } + break; + } + case TASKMGMT_CMD_CMPLT_OKAY: + { + u_int scbid; + struct scb *scb; + + /* + * An ABORT TASK TMF failed to be delivered before + * the targeted command completed normally. + */ + scbid = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scbid); + if (scb != NULL) { + /* + * Remove the second instance of this SCB from + * the QINFIFO if it is still there. + */ + ahd_print_path(ahd, scb); + printk("SCB completes before TMF\n"); + /* + * Handle losing the race. Wait until any + * current selection completes. We will then + * set the TMF back to zero in this SCB so that + * the sequencer doesn't bother to issue another + * sequencer interrupt for its completion. + */ + while ((ahd_inb(ahd, SCSISEQ0) & ENSELO) != 0 + && (ahd_inb(ahd, SSTAT0) & SELDO) == 0 + && (ahd_inb(ahd, SSTAT1) & SELTO) == 0) + ; + ahd_outb(ahd, SCB_TASK_MANAGEMENT, 0); + ahd_search_qinfifo(ahd, SCB_GET_TARGET(ahd, scb), + SCB_GET_CHANNEL(ahd, scb), + SCB_GET_LUN(scb), SCB_GET_TAG(scb), + ROLE_INITIATOR, /*status*/0, + SEARCH_REMOVE); + } + break; + } + case TRACEPOINT0: + case TRACEPOINT1: + case TRACEPOINT2: + case TRACEPOINT3: + printk("%s: Tracepoint %d\n", ahd_name(ahd), + seqintcode - TRACEPOINT0); + break; + case NO_SEQINT: + break; + case SAW_HWERR: + ahd_handle_hwerrint(ahd); + break; + default: + printk("%s: Unexpected SEQINTCODE %d\n", ahd_name(ahd), + seqintcode); + break; + } + /* + * The sequencer is paused immediately on + * a SEQINT, so we should restart it when + * we're done. + */ + ahd_unpause(ahd); +} + +static void +ahd_handle_scsiint(struct ahd_softc *ahd, u_int intstat) +{ + struct scb *scb; + u_int status0; + u_int status3; + u_int status; + u_int lqistat1; + u_int lqostat0; + u_int scbid; + u_int busfreetime; + + ahd_update_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + + status3 = ahd_inb(ahd, SSTAT3) & (NTRAMPERR|OSRAMPERR); + status0 = ahd_inb(ahd, SSTAT0) & (IOERR|OVERRUN|SELDI|SELDO); + status = ahd_inb(ahd, SSTAT1) & (SELTO|SCSIRSTI|BUSFREE|SCSIPERR); + lqistat1 = ahd_inb(ahd, LQISTAT1); + lqostat0 = ahd_inb(ahd, LQOSTAT0); + busfreetime = ahd_inb(ahd, SSTAT2) & BUSFREETIME; + + /* + * Ignore external resets after a bus reset. + */ + if (((status & SCSIRSTI) != 0) && (ahd->flags & AHD_BUS_RESET_ACTIVE)) { + ahd_outb(ahd, CLRSINT1, CLRSCSIRSTI); + return; + } + + /* + * Clear bus reset flag + */ + ahd->flags &= ~AHD_BUS_RESET_ACTIVE; + + if ((status0 & (SELDI|SELDO)) != 0) { + u_int simode0; + + ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); + simode0 = ahd_inb(ahd, SIMODE0); + status0 &= simode0 & (IOERR|OVERRUN|SELDI|SELDO); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + } + scbid = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scbid); + if (scb != NULL + && (ahd_inb(ahd, SEQ_FLAGS) & NOT_IDENTIFIED) != 0) + scb = NULL; + + if ((status0 & IOERR) != 0) { + u_int now_lvd; + + now_lvd = ahd_inb(ahd, SBLKCTL) & ENAB40; + printk("%s: Transceiver State Has Changed to %s mode\n", + ahd_name(ahd), now_lvd ? "LVD" : "SE"); + ahd_outb(ahd, CLRSINT0, CLRIOERR); + /* + * A change in I/O mode is equivalent to a bus reset. + */ + ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE); + ahd_pause(ahd); + ahd_setup_iocell_workaround(ahd); + ahd_unpause(ahd); + } else if ((status0 & OVERRUN) != 0) { + + printk("%s: SCSI offset overrun detected. Resetting bus.\n", + ahd_name(ahd)); + ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE); + } else if ((status & SCSIRSTI) != 0) { + + printk("%s: Someone reset channel A\n", ahd_name(ahd)); + ahd_reset_channel(ahd, 'A', /*Initiate Reset*/FALSE); + } else if ((status & SCSIPERR) != 0) { + + /* Make sure the sequencer is in a safe location. */ + ahd_clear_critical_section(ahd); + + ahd_handle_transmission_error(ahd); + } else if (lqostat0 != 0) { + + printk("%s: lqostat0 == 0x%x!\n", ahd_name(ahd), lqostat0); + ahd_outb(ahd, CLRLQOINT0, lqostat0); + if ((ahd->bugs & AHD_CLRLQO_AUTOCLR_BUG) != 0) + ahd_outb(ahd, CLRLQOINT1, 0); + } else if ((status & SELTO) != 0) { + /* Stop the selection */ + ahd_outb(ahd, SCSISEQ0, 0); + + /* Make sure the sequencer is in a safe location. */ + ahd_clear_critical_section(ahd); + + /* No more pending messages */ + ahd_clear_msg_state(ahd); + + /* Clear interrupt state */ + ahd_outb(ahd, CLRSINT1, CLRSELTIMEO|CLRBUSFREE|CLRSCSIPERR); + + /* + * Although the driver does not care about the + * 'Selection in Progress' status bit, the busy + * LED does. SELINGO is only cleared by a successful + * selection, so we must manually clear it to insure + * the LED turns off just incase no future successful + * selections occur (e.g. no devices on the bus). + */ + ahd_outb(ahd, CLRSINT0, CLRSELINGO); + + scbid = ahd_inw(ahd, WAITING_TID_HEAD); + scb = ahd_lookup_scb(ahd, scbid); + if (scb == NULL) { + printk("%s: ahd_intr - referenced scb not " + "valid during SELTO scb(0x%x)\n", + ahd_name(ahd), scbid); + ahd_dump_card_state(ahd); + } else { + struct ahd_devinfo devinfo; +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_SELTO) != 0) { + ahd_print_path(ahd, scb); + printk("Saw Selection Timeout for SCB 0x%x\n", + scbid); + } +#endif + ahd_scb_devinfo(ahd, &devinfo, scb); + ahd_set_transaction_status(scb, CAM_SEL_TIMEOUT); + ahd_freeze_devq(ahd, scb); + + /* + * Cancel any pending transactions on the device + * now that it seems to be missing. This will + * also revert us to async/narrow transfers until + * we can renegotiate with the device. + */ + ahd_handle_devreset(ahd, &devinfo, + CAM_LUN_WILDCARD, + CAM_SEL_TIMEOUT, + "Selection Timeout", + /*verbose_level*/1); + } + ahd_outb(ahd, CLRINT, CLRSCSIINT); + ahd_iocell_first_selection(ahd); + ahd_unpause(ahd); + } else if ((status0 & (SELDI|SELDO)) != 0) { + + ahd_iocell_first_selection(ahd); + ahd_unpause(ahd); + } else if (status3 != 0) { + printk("%s: SCSI Cell parity error SSTAT3 == 0x%x\n", + ahd_name(ahd), status3); + ahd_outb(ahd, CLRSINT3, status3); + } else if ((lqistat1 & (LQIPHASE_LQ|LQIPHASE_NLQ)) != 0) { + + /* Make sure the sequencer is in a safe location. */ + ahd_clear_critical_section(ahd); + + ahd_handle_lqiphase_error(ahd, lqistat1); + } else if ((lqistat1 & LQICRCI_NLQ) != 0) { + /* + * This status can be delayed during some + * streaming operations. The SCSIPHASE + * handler has already dealt with this case + * so just clear the error. + */ + ahd_outb(ahd, CLRLQIINT1, CLRLQICRCI_NLQ); + } else if ((status & BUSFREE) != 0 + || (lqistat1 & LQOBUSFREE) != 0) { + u_int lqostat1; + int restart; + int clear_fifo; + int packetized; + u_int mode; + + /* + * Clear our selection hardware as soon as possible. + * We may have an entry in the waiting Q for this target, + * that is affected by this busfree and we don't want to + * go about selecting the target while we handle the event. + */ + ahd_outb(ahd, SCSISEQ0, 0); + + /* Make sure the sequencer is in a safe location. */ + ahd_clear_critical_section(ahd); + + /* + * Determine what we were up to at the time of + * the busfree. + */ + mode = AHD_MODE_SCSI; + busfreetime = ahd_inb(ahd, SSTAT2) & BUSFREETIME; + lqostat1 = ahd_inb(ahd, LQOSTAT1); + switch (busfreetime) { + case BUSFREE_DFF0: + case BUSFREE_DFF1: + { + mode = busfreetime == BUSFREE_DFF0 + ? AHD_MODE_DFF0 : AHD_MODE_DFF1; + ahd_set_modes(ahd, mode, mode); + scbid = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scbid); + if (scb == NULL) { + printk("%s: Invalid SCB %d in DFF%d " + "during unexpected busfree\n", + ahd_name(ahd), scbid, mode); + packetized = 0; + } else + packetized = (scb->flags & SCB_PACKETIZED) != 0; + clear_fifo = 1; + break; + } + case BUSFREE_LQO: + clear_fifo = 0; + packetized = 1; + break; + default: + clear_fifo = 0; + packetized = (lqostat1 & LQOBUSFREE) != 0; + if (!packetized + && ahd_inb(ahd, LASTPHASE) == P_BUSFREE + && (ahd_inb(ahd, SSTAT0) & SELDI) == 0 + && ((ahd_inb(ahd, SSTAT0) & SELDO) == 0 + || (ahd_inb(ahd, SCSISEQ0) & ENSELO) == 0)) + /* + * Assume packetized if we are not + * on the bus in a non-packetized + * capacity and any pending selection + * was a packetized selection. + */ + packetized = 1; + break; + } + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MISC) != 0) + printk("Saw Busfree. Busfreetime = 0x%x.\n", + busfreetime); +#endif + /* + * Busfrees that occur in non-packetized phases are + * handled by the nonpkt_busfree handler. + */ + if (packetized && ahd_inb(ahd, LASTPHASE) == P_BUSFREE) { + restart = ahd_handle_pkt_busfree(ahd, busfreetime); + } else { + packetized = 0; + restart = ahd_handle_nonpkt_busfree(ahd); + } + /* + * Clear the busfree interrupt status. The setting of + * the interrupt is a pulse, so in a perfect world, we + * would not need to muck with the ENBUSFREE logic. This + * would ensure that if the bus moves on to another + * connection, busfree protection is still in force. If + * BUSFREEREV is broken, however, we must manually clear + * the ENBUSFREE if the busfree occurred during a non-pack + * connection so that we don't get false positives during + * future, packetized, connections. + */ + ahd_outb(ahd, CLRSINT1, CLRBUSFREE); + if (packetized == 0 + && (ahd->bugs & AHD_BUSFREEREV_BUG) != 0) + ahd_outb(ahd, SIMODE1, + ahd_inb(ahd, SIMODE1) & ~ENBUSFREE); + + if (clear_fifo) + ahd_clear_fifo(ahd, mode); + + ahd_clear_msg_state(ahd); + ahd_outb(ahd, CLRINT, CLRSCSIINT); + if (restart) { + ahd_restart(ahd); + } else { + ahd_unpause(ahd); + } + } else { + printk("%s: Missing case in ahd_handle_scsiint. status = %x\n", + ahd_name(ahd), status); + ahd_dump_card_state(ahd); + ahd_clear_intstat(ahd); + ahd_unpause(ahd); + } +} + +static void +ahd_handle_transmission_error(struct ahd_softc *ahd) +{ + struct scb *scb; + u_int scbid; + u_int lqistat1; + u_int msg_out; + u_int curphase; + u_int lastphase; + u_int perrdiag; + u_int cur_col; + int silent; + + scb = NULL; + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + lqistat1 = ahd_inb(ahd, LQISTAT1) & ~(LQIPHASE_LQ|LQIPHASE_NLQ); + ahd_inb(ahd, LQISTAT2); + if ((lqistat1 & (LQICRCI_NLQ|LQICRCI_LQ)) == 0 + && (ahd->bugs & AHD_NLQICRC_DELAYED_BUG) != 0) { + u_int lqistate; + + ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); + lqistate = ahd_inb(ahd, LQISTATE); + if ((lqistate >= 0x1E && lqistate <= 0x24) + || (lqistate == 0x29)) { +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_RECOVERY) != 0) { + printk("%s: NLQCRC found via LQISTATE\n", + ahd_name(ahd)); + } +#endif + lqistat1 |= LQICRCI_NLQ; + } + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + } + + ahd_outb(ahd, CLRLQIINT1, lqistat1); + lastphase = ahd_inb(ahd, LASTPHASE); + curphase = ahd_inb(ahd, SCSISIGI) & PHASE_MASK; + perrdiag = ahd_inb(ahd, PERRDIAG); + msg_out = MSG_INITIATOR_DET_ERR; + ahd_outb(ahd, CLRSINT1, CLRSCSIPERR); + + /* + * Try to find the SCB associated with this error. + */ + silent = FALSE; + if (lqistat1 == 0 + || (lqistat1 & LQICRCI_NLQ) != 0) { + if ((lqistat1 & (LQICRCI_NLQ|LQIOVERI_NLQ)) != 0) + ahd_set_active_fifo(ahd); + scbid = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scbid); + if (scb != NULL && SCB_IS_SILENT(scb)) + silent = TRUE; + } + + cur_col = 0; + if (silent == FALSE) { + printk("%s: Transmission error detected\n", ahd_name(ahd)); + ahd_lqistat1_print(lqistat1, &cur_col, 50); + ahd_lastphase_print(lastphase, &cur_col, 50); + ahd_scsisigi_print(curphase, &cur_col, 50); + ahd_perrdiag_print(perrdiag, &cur_col, 50); + printk("\n"); + ahd_dump_card_state(ahd); + } + + if ((lqistat1 & (LQIOVERI_LQ|LQIOVERI_NLQ)) != 0) { + if (silent == FALSE) { + printk("%s: Gross protocol error during incoming " + "packet. lqistat1 == 0x%x. Resetting bus.\n", + ahd_name(ahd), lqistat1); + } + ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE); + return; + } else if ((lqistat1 & LQICRCI_LQ) != 0) { + /* + * A CRC error has been detected on an incoming LQ. + * The bus is currently hung on the last ACK. + * Hit LQIRETRY to release the last ack, and + * wait for the sequencer to determine that ATNO + * is asserted while in message out to take us + * to our host message loop. No NONPACKREQ or + * LQIPHASE type errors will occur in this + * scenario. After this first LQIRETRY, the LQI + * manager will be in ISELO where it will + * happily sit until another packet phase begins. + * Unexpected bus free detection is enabled + * through any phases that occur after we release + * this last ack until the LQI manager sees a + * packet phase. This implies we may have to + * ignore a perfectly valid "unexected busfree" + * after our "initiator detected error" message is + * sent. A busfree is the expected response after + * we tell the target that it's L_Q was corrupted. + * (SPI4R09 10.7.3.3.3) + */ + ahd_outb(ahd, LQCTL2, LQIRETRY); + printk("LQIRetry for LQICRCI_LQ to release ACK\n"); + } else if ((lqistat1 & LQICRCI_NLQ) != 0) { + /* + * We detected a CRC error in a NON-LQ packet. + * The hardware has varying behavior in this situation + * depending on whether this packet was part of a + * stream or not. + * + * PKT by PKT mode: + * The hardware has already acked the complete packet. + * If the target honors our outstanding ATN condition, + * we should be (or soon will be) in MSGOUT phase. + * This will trigger the LQIPHASE_LQ status bit as the + * hardware was expecting another LQ. Unexpected + * busfree detection is enabled. Once LQIPHASE_LQ is + * true (first entry into host message loop is much + * the same), we must clear LQIPHASE_LQ and hit + * LQIRETRY so the hardware is ready to handle + * a future LQ. NONPACKREQ will not be asserted again + * once we hit LQIRETRY until another packet is + * processed. The target may either go busfree + * or start another packet in response to our message. + * + * Read Streaming P0 asserted: + * If we raise ATN and the target completes the entire + * stream (P0 asserted during the last packet), the + * hardware will ack all data and return to the ISTART + * state. When the target reponds to our ATN condition, + * LQIPHASE_LQ will be asserted. We should respond to + * this with an LQIRETRY to prepare for any future + * packets. NONPACKREQ will not be asserted again + * once we hit LQIRETRY until another packet is + * processed. The target may either go busfree or + * start another packet in response to our message. + * Busfree detection is enabled. + * + * Read Streaming P0 not asserted: + * If we raise ATN and the target transitions to + * MSGOUT in or after a packet where P0 is not + * asserted, the hardware will assert LQIPHASE_NLQ. + * We should respond to the LQIPHASE_NLQ with an + * LQIRETRY. Should the target stay in a non-pkt + * phase after we send our message, the hardware + * will assert LQIPHASE_LQ. Recovery is then just as + * listed above for the read streaming with P0 asserted. + * Busfree detection is enabled. + */ + if (silent == FALSE) + printk("LQICRC_NLQ\n"); + if (scb == NULL) { + printk("%s: No SCB valid for LQICRC_NLQ. " + "Resetting bus\n", ahd_name(ahd)); + ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE); + return; + } + } else if ((lqistat1 & LQIBADLQI) != 0) { + printk("Need to handle BADLQI!\n"); + ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE); + return; + } else if ((perrdiag & (PARITYERR|PREVPHASE)) == PARITYERR) { + if ((curphase & ~P_DATAIN_DT) != 0) { + /* Ack the byte. So we can continue. */ + if (silent == FALSE) + printk("Acking %s to clear perror\n", + ahd_lookup_phase_entry(curphase)->phasemsg); + ahd_inb(ahd, SCSIDAT); + } + + if (curphase == P_MESGIN) + msg_out = MSG_PARITY_ERROR; + } + + /* + * We've set the hardware to assert ATN if we + * get a parity error on "in" phases, so all we + * need to do is stuff the message buffer with + * the appropriate message. "In" phases have set + * mesg_out to something other than MSG_NOP. + */ + ahd->send_msg_perror = msg_out; + if (scb != NULL && msg_out == MSG_INITIATOR_DET_ERR) + scb->flags |= SCB_TRANSMISSION_ERROR; + ahd_outb(ahd, MSG_OUT, HOST_MSG); + ahd_outb(ahd, CLRINT, CLRSCSIINT); + ahd_unpause(ahd); +} + +static void +ahd_handle_lqiphase_error(struct ahd_softc *ahd, u_int lqistat1) +{ + /* + * Clear the sources of the interrupts. + */ + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + ahd_outb(ahd, CLRLQIINT1, lqistat1); + + /* + * If the "illegal" phase changes were in response + * to our ATN to flag a CRC error, AND we ended up + * on packet boundaries, clear the error, restart the + * LQI manager as appropriate, and go on our merry + * way toward sending the message. Otherwise, reset + * the bus to clear the error. + */ + ahd_set_active_fifo(ahd); + if ((ahd_inb(ahd, SCSISIGO) & ATNO) != 0 + && (ahd_inb(ahd, MDFFSTAT) & DLZERO) != 0) { + if ((lqistat1 & LQIPHASE_LQ) != 0) { + printk("LQIRETRY for LQIPHASE_LQ\n"); + ahd_outb(ahd, LQCTL2, LQIRETRY); + } else if ((lqistat1 & LQIPHASE_NLQ) != 0) { + printk("LQIRETRY for LQIPHASE_NLQ\n"); + ahd_outb(ahd, LQCTL2, LQIRETRY); + } else + panic("ahd_handle_lqiphase_error: No phase errors\n"); + ahd_dump_card_state(ahd); + ahd_outb(ahd, CLRINT, CLRSCSIINT); + ahd_unpause(ahd); + } else { + printk("Resetting Channel for LQI Phase error\n"); + ahd_dump_card_state(ahd); + ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE); + } +} + +/* + * Packetized unexpected or expected busfree. + * Entered in mode based on busfreetime. + */ +static int +ahd_handle_pkt_busfree(struct ahd_softc *ahd, u_int busfreetime) +{ + u_int lqostat1; + + AHD_ASSERT_MODES(ahd, ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK), + ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK)); + lqostat1 = ahd_inb(ahd, LQOSTAT1); + if ((lqostat1 & LQOBUSFREE) != 0) { + struct scb *scb; + u_int scbid; + u_int saved_scbptr; + u_int waiting_h; + u_int waiting_t; + u_int next; + + /* + * The LQO manager detected an unexpected busfree + * either: + * + * 1) During an outgoing LQ. + * 2) After an outgoing LQ but before the first + * REQ of the command packet. + * 3) During an outgoing command packet. + * + * In all cases, CURRSCB is pointing to the + * SCB that encountered the failure. Clean + * up the queue, clear SELDO and LQOBUSFREE, + * and allow the sequencer to restart the select + * out at its lesure. + */ + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + scbid = ahd_inw(ahd, CURRSCB); + scb = ahd_lookup_scb(ahd, scbid); + if (scb == NULL) + panic("SCB not valid during LQOBUSFREE"); + /* + * Clear the status. + */ + ahd_outb(ahd, CLRLQOINT1, CLRLQOBUSFREE); + if ((ahd->bugs & AHD_CLRLQO_AUTOCLR_BUG) != 0) + ahd_outb(ahd, CLRLQOINT1, 0); + ahd_outb(ahd, SCSISEQ0, ahd_inb(ahd, SCSISEQ0) & ~ENSELO); + ahd_flush_device_writes(ahd); + ahd_outb(ahd, CLRSINT0, CLRSELDO); + + /* + * Return the LQO manager to its idle loop. It will + * not do this automatically if the busfree occurs + * after the first REQ of either the LQ or command + * packet or between the LQ and command packet. + */ + ahd_outb(ahd, LQCTL2, ahd_inb(ahd, LQCTL2) | LQOTOIDLE); + + /* + * Update the waiting for selection queue so + * we restart on the correct SCB. + */ + waiting_h = ahd_inw(ahd, WAITING_TID_HEAD); + saved_scbptr = ahd_get_scbptr(ahd); + if (waiting_h != scbid) { + + ahd_outw(ahd, WAITING_TID_HEAD, scbid); + waiting_t = ahd_inw(ahd, WAITING_TID_TAIL); + if (waiting_t == waiting_h) { + ahd_outw(ahd, WAITING_TID_TAIL, scbid); + next = SCB_LIST_NULL; + } else { + ahd_set_scbptr(ahd, waiting_h); + next = ahd_inw_scbram(ahd, SCB_NEXT2); + } + ahd_set_scbptr(ahd, scbid); + ahd_outw(ahd, SCB_NEXT2, next); + } + ahd_set_scbptr(ahd, saved_scbptr); + if (scb->crc_retry_count < AHD_MAX_LQ_CRC_ERRORS) { + if (SCB_IS_SILENT(scb) == FALSE) { + ahd_print_path(ahd, scb); + printk("Probable outgoing LQ CRC error. " + "Retrying command\n"); + } + scb->crc_retry_count++; + } else { + ahd_set_transaction_status(scb, CAM_UNCOR_PARITY); + ahd_freeze_scb(scb); + ahd_freeze_devq(ahd, scb); + } + /* Return unpausing the sequencer. */ + return (0); + } else if ((ahd_inb(ahd, PERRDIAG) & PARITYERR) != 0) { + /* + * Ignore what are really parity errors that + * occur on the last REQ of a free running + * clock prior to going busfree. Some drives + * do not properly active negate just before + * going busfree resulting in a parity glitch. + */ + ahd_outb(ahd, CLRSINT1, CLRSCSIPERR|CLRBUSFREE); +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MASKED_ERRORS) != 0) + printk("%s: Parity on last REQ detected " + "during busfree phase.\n", + ahd_name(ahd)); +#endif + /* Return unpausing the sequencer. */ + return (0); + } + if (ahd->src_mode != AHD_MODE_SCSI) { + u_int scbid; + struct scb *scb; + + scbid = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scbid); + ahd_print_path(ahd, scb); + printk("Unexpected PKT busfree condition\n"); + ahd_dump_card_state(ahd); + ahd_abort_scbs(ahd, SCB_GET_TARGET(ahd, scb), 'A', + SCB_GET_LUN(scb), SCB_GET_TAG(scb), + ROLE_INITIATOR, CAM_UNEXP_BUSFREE); + + /* Return restarting the sequencer. */ + return (1); + } + printk("%s: Unexpected PKT busfree condition\n", ahd_name(ahd)); + ahd_dump_card_state(ahd); + /* Restart the sequencer. */ + return (1); +} + +/* + * Non-packetized unexpected or expected busfree. + */ +static int +ahd_handle_nonpkt_busfree(struct ahd_softc *ahd) +{ + struct ahd_devinfo devinfo; + struct scb *scb; + u_int lastphase; + u_int saved_scsiid; + u_int saved_lun; + u_int target; + u_int initiator_role_id; + u_int scbid; + u_int ppr_busfree; + int printerror; + + /* + * Look at what phase we were last in. If its message out, + * chances are pretty good that the busfree was in response + * to one of our abort requests. + */ + lastphase = ahd_inb(ahd, LASTPHASE); + saved_scsiid = ahd_inb(ahd, SAVED_SCSIID); + saved_lun = ahd_inb(ahd, SAVED_LUN); + target = SCSIID_TARGET(ahd, saved_scsiid); + initiator_role_id = SCSIID_OUR_ID(saved_scsiid); + ahd_compile_devinfo(&devinfo, initiator_role_id, + target, saved_lun, 'A', ROLE_INITIATOR); + printerror = 1; + + scbid = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scbid); + if (scb != NULL + && (ahd_inb(ahd, SEQ_FLAGS) & NOT_IDENTIFIED) != 0) + scb = NULL; + + ppr_busfree = (ahd->msg_flags & MSG_FLAG_EXPECT_PPR_BUSFREE) != 0; + if (lastphase == P_MESGOUT) { + u_int tag; + + tag = SCB_LIST_NULL; + if (ahd_sent_msg(ahd, AHDMSG_1B, MSG_ABORT_TAG, TRUE) + || ahd_sent_msg(ahd, AHDMSG_1B, MSG_ABORT, TRUE)) { + int found; + int sent_msg; + + if (scb == NULL) { + ahd_print_devinfo(ahd, &devinfo); + printk("Abort for unidentified " + "connection completed.\n"); + /* restart the sequencer. */ + return (1); + } + sent_msg = ahd->msgout_buf[ahd->msgout_index - 1]; + ahd_print_path(ahd, scb); + printk("SCB %d - Abort%s Completed.\n", + SCB_GET_TAG(scb), + sent_msg == MSG_ABORT_TAG ? "" : " Tag"); + + if (sent_msg == MSG_ABORT_TAG) + tag = SCB_GET_TAG(scb); + + if ((scb->flags & SCB_EXTERNAL_RESET) != 0) { + /* + * This abort is in response to an + * unexpected switch to command phase + * for a packetized connection. Since + * the identify message was never sent, + * "saved lun" is 0. We really want to + * abort only the SCB that encountered + * this error, which could have a different + * lun. The SCB will be retried so the OS + * will see the UA after renegotiating to + * packetized. + */ + tag = SCB_GET_TAG(scb); + saved_lun = scb->hscb->lun; + } + found = ahd_abort_scbs(ahd, target, 'A', saved_lun, + tag, ROLE_INITIATOR, + CAM_REQ_ABORTED); + printk("found == 0x%x\n", found); + printerror = 0; + } else if (ahd_sent_msg(ahd, AHDMSG_1B, + MSG_BUS_DEV_RESET, TRUE)) { + ahd_handle_devreset(ahd, &devinfo, CAM_LUN_WILDCARD, + CAM_BDR_SENT, "Bus Device Reset", + /*verbose_level*/0); + printerror = 0; + } else if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_PPR, FALSE) + && ppr_busfree == 0) { + struct ahd_initiator_tinfo *tinfo; + struct ahd_tmode_tstate *tstate; + + /* + * PPR Rejected. + * + * If the previous negotiation was packetized, + * this could be because the device has been + * reset without our knowledge. Force our + * current negotiation to async and retry the + * negotiation. Otherwise retry the command + * with non-ppr negotiation. + */ +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) + printk("PPR negotiation rejected busfree.\n"); +#endif + tinfo = ahd_fetch_transinfo(ahd, devinfo.channel, + devinfo.our_scsiid, + devinfo.target, &tstate); + if ((tinfo->curr.ppr_options & MSG_EXT_PPR_IU_REQ)!=0) { + ahd_set_width(ahd, &devinfo, + MSG_EXT_WDTR_BUS_8_BIT, + AHD_TRANS_CUR, + /*paused*/TRUE); + ahd_set_syncrate(ahd, &devinfo, + /*period*/0, /*offset*/0, + /*ppr_options*/0, + AHD_TRANS_CUR, + /*paused*/TRUE); + /* + * The expect PPR busfree handler below + * will effect the retry and necessary + * abort. + */ + } else { + tinfo->curr.transport_version = 2; + tinfo->goal.transport_version = 2; + tinfo->goal.ppr_options = 0; + if (scb != NULL) { + /* + * Remove any SCBs in the waiting + * for selection queue that may + * also be for this target so that + * command ordering is preserved. + */ + ahd_freeze_devq(ahd, scb); + ahd_qinfifo_requeue_tail(ahd, scb); + } + printerror = 0; + } + } else if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_WDTR, FALSE) + && ppr_busfree == 0) { + /* + * Negotiation Rejected. Go-narrow and + * retry command. + */ +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) + printk("WDTR negotiation rejected busfree.\n"); +#endif + ahd_set_width(ahd, &devinfo, + MSG_EXT_WDTR_BUS_8_BIT, + AHD_TRANS_CUR|AHD_TRANS_GOAL, + /*paused*/TRUE); + if (scb != NULL) { + /* + * Remove any SCBs in the waiting for + * selection queue that may also be for + * this target so that command ordering + * is preserved. + */ + ahd_freeze_devq(ahd, scb); + ahd_qinfifo_requeue_tail(ahd, scb); + } + printerror = 0; + } else if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_SDTR, FALSE) + && ppr_busfree == 0) { + /* + * Negotiation Rejected. Go-async and + * retry command. + */ +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) + printk("SDTR negotiation rejected busfree.\n"); +#endif + ahd_set_syncrate(ahd, &devinfo, + /*period*/0, /*offset*/0, + /*ppr_options*/0, + AHD_TRANS_CUR|AHD_TRANS_GOAL, + /*paused*/TRUE); + if (scb != NULL) { + /* + * Remove any SCBs in the waiting for + * selection queue that may also be for + * this target so that command ordering + * is preserved. + */ + ahd_freeze_devq(ahd, scb); + ahd_qinfifo_requeue_tail(ahd, scb); + } + printerror = 0; + } else if ((ahd->msg_flags & MSG_FLAG_EXPECT_IDE_BUSFREE) != 0 + && ahd_sent_msg(ahd, AHDMSG_1B, + MSG_INITIATOR_DET_ERR, TRUE)) { + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) + printk("Expected IDE Busfree\n"); +#endif + printerror = 0; + } else if ((ahd->msg_flags & MSG_FLAG_EXPECT_QASREJ_BUSFREE) + && ahd_sent_msg(ahd, AHDMSG_1B, + MSG_MESSAGE_REJECT, TRUE)) { + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) + printk("Expected QAS Reject Busfree\n"); +#endif + printerror = 0; + } + } + + /* + * The busfree required flag is honored at the end of + * the message phases. We check it last in case we + * had to send some other message that caused a busfree. + */ + if (scb != NULL && printerror != 0 + && (lastphase == P_MESGIN || lastphase == P_MESGOUT) + && ((ahd->msg_flags & MSG_FLAG_EXPECT_PPR_BUSFREE) != 0)) { + + ahd_freeze_devq(ahd, scb); + ahd_set_transaction_status(scb, CAM_REQUEUE_REQ); + ahd_freeze_scb(scb); + if ((ahd->msg_flags & MSG_FLAG_IU_REQ_CHANGED) != 0) { + ahd_abort_scbs(ahd, SCB_GET_TARGET(ahd, scb), + SCB_GET_CHANNEL(ahd, scb), + SCB_GET_LUN(scb), SCB_LIST_NULL, + ROLE_INITIATOR, CAM_REQ_ABORTED); + } else { +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) + printk("PPR Negotiation Busfree.\n"); +#endif + ahd_done(ahd, scb); + } + printerror = 0; + } + if (printerror != 0) { + int aborted; + + aborted = 0; + if (scb != NULL) { + u_int tag; + + if ((scb->hscb->control & TAG_ENB) != 0) + tag = SCB_GET_TAG(scb); + else + tag = SCB_LIST_NULL; + ahd_print_path(ahd, scb); + aborted = ahd_abort_scbs(ahd, target, 'A', + SCB_GET_LUN(scb), tag, + ROLE_INITIATOR, + CAM_UNEXP_BUSFREE); + } else { + /* + * We had not fully identified this connection, + * so we cannot abort anything. + */ + printk("%s: ", ahd_name(ahd)); + } + printk("Unexpected busfree %s, %d SCBs aborted, " + "PRGMCNT == 0x%x\n", + ahd_lookup_phase_entry(lastphase)->phasemsg, + aborted, + ahd_inw(ahd, PRGMCNT)); + ahd_dump_card_state(ahd); + if (lastphase != P_BUSFREE) + ahd_force_renegotiation(ahd, &devinfo); + } + /* Always restart the sequencer. */ + return (1); +} + +static void +ahd_handle_proto_violation(struct ahd_softc *ahd) +{ + struct ahd_devinfo devinfo; + struct scb *scb; + u_int scbid; + u_int seq_flags; + u_int curphase; + u_int lastphase; + int found; + + ahd_fetch_devinfo(ahd, &devinfo); + scbid = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scbid); + seq_flags = ahd_inb(ahd, SEQ_FLAGS); + curphase = ahd_inb(ahd, SCSISIGI) & PHASE_MASK; + lastphase = ahd_inb(ahd, LASTPHASE); + if ((seq_flags & NOT_IDENTIFIED) != 0) { + + /* + * The reconnecting target either did not send an + * identify message, or did, but we didn't find an SCB + * to match. + */ + ahd_print_devinfo(ahd, &devinfo); + printk("Target did not send an IDENTIFY message. " + "LASTPHASE = 0x%x.\n", lastphase); + scb = NULL; + } else if (scb == NULL) { + /* + * We don't seem to have an SCB active for this + * transaction. Print an error and reset the bus. + */ + ahd_print_devinfo(ahd, &devinfo); + printk("No SCB found during protocol violation\n"); + goto proto_violation_reset; + } else { + ahd_set_transaction_status(scb, CAM_SEQUENCE_FAIL); + if ((seq_flags & NO_CDB_SENT) != 0) { + ahd_print_path(ahd, scb); + printk("No or incomplete CDB sent to device.\n"); + } else if ((ahd_inb_scbram(ahd, SCB_CONTROL) + & STATUS_RCVD) == 0) { + /* + * The target never bothered to provide status to + * us prior to completing the command. Since we don't + * know the disposition of this command, we must attempt + * to abort it. Assert ATN and prepare to send an abort + * message. + */ + ahd_print_path(ahd, scb); + printk("Completed command without status.\n"); + } else { + ahd_print_path(ahd, scb); + printk("Unknown protocol violation.\n"); + ahd_dump_card_state(ahd); + } + } + if ((lastphase & ~P_DATAIN_DT) == 0 + || lastphase == P_COMMAND) { +proto_violation_reset: + /* + * Target either went directly to data + * phase or didn't respond to our ATN. + * The only safe thing to do is to blow + * it away with a bus reset. + */ + found = ahd_reset_channel(ahd, 'A', TRUE); + printk("%s: Issued Channel %c Bus Reset. " + "%d SCBs aborted\n", ahd_name(ahd), 'A', found); + } else { + /* + * Leave the selection hardware off in case + * this abort attempt will affect yet to + * be sent commands. + */ + ahd_outb(ahd, SCSISEQ0, + ahd_inb(ahd, SCSISEQ0) & ~ENSELO); + ahd_assert_atn(ahd); + ahd_outb(ahd, MSG_OUT, HOST_MSG); + if (scb == NULL) { + ahd_print_devinfo(ahd, &devinfo); + ahd->msgout_buf[0] = MSG_ABORT_TASK; + ahd->msgout_len = 1; + ahd->msgout_index = 0; + ahd->msg_type = MSG_TYPE_INITIATOR_MSGOUT; + } else { + ahd_print_path(ahd, scb); + scb->flags |= SCB_ABORT; + } + printk("Protocol violation %s. Attempting to abort.\n", + ahd_lookup_phase_entry(curphase)->phasemsg); + } +} + +/* + * Force renegotiation to occur the next time we initiate + * a command to the current device. + */ +static void +ahd_force_renegotiation(struct ahd_softc *ahd, struct ahd_devinfo *devinfo) +{ + struct ahd_initiator_tinfo *targ_info; + struct ahd_tmode_tstate *tstate; + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) { + ahd_print_devinfo(ahd, devinfo); + printk("Forcing renegotiation\n"); + } +#endif + targ_info = ahd_fetch_transinfo(ahd, + devinfo->channel, + devinfo->our_scsiid, + devinfo->target, + &tstate); + ahd_update_neg_request(ahd, devinfo, tstate, + targ_info, AHD_NEG_IF_NON_ASYNC); +} + +#define AHD_MAX_STEPS 2000 +static void +ahd_clear_critical_section(struct ahd_softc *ahd) +{ + ahd_mode_state saved_modes; + int stepping; + int steps; + int first_instr; + u_int simode0; + u_int simode1; + u_int simode3; + u_int lqimode0; + u_int lqimode1; + u_int lqomode0; + u_int lqomode1; + + if (ahd->num_critical_sections == 0) + return; + + stepping = FALSE; + steps = 0; + first_instr = 0; + simode0 = 0; + simode1 = 0; + simode3 = 0; + lqimode0 = 0; + lqimode1 = 0; + lqomode0 = 0; + lqomode1 = 0; + saved_modes = ahd_save_modes(ahd); + for (;;) { + struct cs *cs; + u_int seqaddr; + u_int i; + + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + seqaddr = ahd_inw(ahd, CURADDR); + + cs = ahd->critical_sections; + for (i = 0; i < ahd->num_critical_sections; i++, cs++) { + + if (cs->begin < seqaddr && cs->end >= seqaddr) + break; + } + + if (i == ahd->num_critical_sections) + break; + + if (steps > AHD_MAX_STEPS) { + printk("%s: Infinite loop in critical section\n" + "%s: First Instruction 0x%x now 0x%x\n", + ahd_name(ahd), ahd_name(ahd), first_instr, + seqaddr); + ahd_dump_card_state(ahd); + panic("critical section loop"); + } + + steps++; +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MISC) != 0) + printk("%s: Single stepping at 0x%x\n", ahd_name(ahd), + seqaddr); +#endif + if (stepping == FALSE) { + + first_instr = seqaddr; + ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); + simode0 = ahd_inb(ahd, SIMODE0); + simode3 = ahd_inb(ahd, SIMODE3); + lqimode0 = ahd_inb(ahd, LQIMODE0); + lqimode1 = ahd_inb(ahd, LQIMODE1); + lqomode0 = ahd_inb(ahd, LQOMODE0); + lqomode1 = ahd_inb(ahd, LQOMODE1); + ahd_outb(ahd, SIMODE0, 0); + ahd_outb(ahd, SIMODE3, 0); + ahd_outb(ahd, LQIMODE0, 0); + ahd_outb(ahd, LQIMODE1, 0); + ahd_outb(ahd, LQOMODE0, 0); + ahd_outb(ahd, LQOMODE1, 0); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + simode1 = ahd_inb(ahd, SIMODE1); + /* + * We don't clear ENBUSFREE. Unfortunately + * we cannot re-enable busfree detection within + * the current connection, so we must leave it + * on while single stepping. + */ + ahd_outb(ahd, SIMODE1, simode1 & ENBUSFREE); + ahd_outb(ahd, SEQCTL0, ahd_inb(ahd, SEQCTL0) | STEP); + stepping = TRUE; + } + ahd_outb(ahd, CLRSINT1, CLRBUSFREE); + ahd_outb(ahd, CLRINT, CLRSCSIINT); + ahd_set_modes(ahd, ahd->saved_src_mode, ahd->saved_dst_mode); + ahd_outb(ahd, HCNTRL, ahd->unpause); + while (!ahd_is_paused(ahd)) + ahd_delay(200); + ahd_update_modes(ahd); + } + if (stepping) { + ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); + ahd_outb(ahd, SIMODE0, simode0); + ahd_outb(ahd, SIMODE3, simode3); + ahd_outb(ahd, LQIMODE0, lqimode0); + ahd_outb(ahd, LQIMODE1, lqimode1); + ahd_outb(ahd, LQOMODE0, lqomode0); + ahd_outb(ahd, LQOMODE1, lqomode1); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + ahd_outb(ahd, SEQCTL0, ahd_inb(ahd, SEQCTL0) & ~STEP); + ahd_outb(ahd, SIMODE1, simode1); + /* + * SCSIINT seems to glitch occasionally when + * the interrupt masks are restored. Clear SCSIINT + * one more time so that only persistent errors + * are seen as a real interrupt. + */ + ahd_outb(ahd, CLRINT, CLRSCSIINT); + } + ahd_restore_modes(ahd, saved_modes); +} + +/* + * Clear any pending interrupt status. + */ +static void +ahd_clear_intstat(struct ahd_softc *ahd) +{ + AHD_ASSERT_MODES(ahd, ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK), + ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK)); + /* Clear any interrupt conditions this may have caused */ + ahd_outb(ahd, CLRLQIINT0, CLRLQIATNQAS|CLRLQICRCT1|CLRLQICRCT2 + |CLRLQIBADLQT|CLRLQIATNLQ|CLRLQIATNCMD); + ahd_outb(ahd, CLRLQIINT1, CLRLQIPHASE_LQ|CLRLQIPHASE_NLQ|CLRLIQABORT + |CLRLQICRCI_LQ|CLRLQICRCI_NLQ|CLRLQIBADLQI + |CLRLQIOVERI_LQ|CLRLQIOVERI_NLQ|CLRNONPACKREQ); + ahd_outb(ahd, CLRLQOINT0, CLRLQOTARGSCBPERR|CLRLQOSTOPT2|CLRLQOATNLQ + |CLRLQOATNPKT|CLRLQOTCRC); + ahd_outb(ahd, CLRLQOINT1, CLRLQOINITSCBPERR|CLRLQOSTOPI2|CLRLQOBADQAS + |CLRLQOBUSFREE|CLRLQOPHACHGINPKT); + if ((ahd->bugs & AHD_CLRLQO_AUTOCLR_BUG) != 0) { + ahd_outb(ahd, CLRLQOINT0, 0); + ahd_outb(ahd, CLRLQOINT1, 0); + } + ahd_outb(ahd, CLRSINT3, CLRNTRAMPERR|CLROSRAMPERR); + ahd_outb(ahd, CLRSINT1, CLRSELTIMEO|CLRATNO|CLRSCSIRSTI + |CLRBUSFREE|CLRSCSIPERR|CLRREQINIT); + ahd_outb(ahd, CLRSINT0, CLRSELDO|CLRSELDI|CLRSELINGO + |CLRIOERR|CLROVERRUN); + ahd_outb(ahd, CLRINT, CLRSCSIINT); +} + +/**************************** Debugging Routines ******************************/ +#ifdef AHD_DEBUG +uint32_t ahd_debug = AHD_DEBUG_OPTS; +#endif + +#if 0 +void +ahd_print_scb(struct scb *scb) +{ + struct hardware_scb *hscb; + int i; + + hscb = scb->hscb; + printk("scb:%p control:0x%x scsiid:0x%x lun:%d cdb_len:%d\n", + (void *)scb, + hscb->control, + hscb->scsiid, + hscb->lun, + hscb->cdb_len); + printk("Shared Data: "); + for (i = 0; i < sizeof(hscb->shared_data.idata.cdb); i++) + printk("%#02x", hscb->shared_data.idata.cdb[i]); + printk(" dataptr:%#x%x datacnt:%#x sgptr:%#x tag:%#x\n", + (uint32_t)((ahd_le64toh(hscb->dataptr) >> 32) & 0xFFFFFFFF), + (uint32_t)(ahd_le64toh(hscb->dataptr) & 0xFFFFFFFF), + ahd_le32toh(hscb->datacnt), + ahd_le32toh(hscb->sgptr), + SCB_GET_TAG(scb)); + ahd_dump_sglist(scb); +} +#endif /* 0 */ + +/************************* Transfer Negotiation *******************************/ +/* + * Allocate per target mode instance (ID we respond to as a target) + * transfer negotiation data structures. + */ +static struct ahd_tmode_tstate * +ahd_alloc_tstate(struct ahd_softc *ahd, u_int scsi_id, char channel) +{ + struct ahd_tmode_tstate *master_tstate; + struct ahd_tmode_tstate *tstate; + int i; + + master_tstate = ahd->enabled_targets[ahd->our_id]; + if (ahd->enabled_targets[scsi_id] != NULL + && ahd->enabled_targets[scsi_id] != master_tstate) + panic("%s: ahd_alloc_tstate - Target already allocated", + ahd_name(ahd)); + tstate = kmalloc(sizeof(*tstate), GFP_ATOMIC); + if (tstate == NULL) + return (NULL); + + /* + * If we have allocated a master tstate, copy user settings from + * the master tstate (taken from SRAM or the EEPROM) for this + * channel, but reset our current and goal settings to async/narrow + * until an initiator talks to us. + */ + if (master_tstate != NULL) { + memcpy(tstate, master_tstate, sizeof(*tstate)); + memset(tstate->enabled_luns, 0, sizeof(tstate->enabled_luns)); + for (i = 0; i < 16; i++) { + memset(&tstate->transinfo[i].curr, 0, + sizeof(tstate->transinfo[i].curr)); + memset(&tstate->transinfo[i].goal, 0, + sizeof(tstate->transinfo[i].goal)); + } + } else + memset(tstate, 0, sizeof(*tstate)); + ahd->enabled_targets[scsi_id] = tstate; + return (tstate); +} + +#ifdef AHD_TARGET_MODE +/* + * Free per target mode instance (ID we respond to as a target) + * transfer negotiation data structures. + */ +static void +ahd_free_tstate(struct ahd_softc *ahd, u_int scsi_id, char channel, int force) +{ + struct ahd_tmode_tstate *tstate; + + /* + * Don't clean up our "master" tstate. + * It has our default user settings. + */ + if (scsi_id == ahd->our_id + && force == FALSE) + return; + + tstate = ahd->enabled_targets[scsi_id]; + kfree(tstate); + ahd->enabled_targets[scsi_id] = NULL; +} +#endif + +/* + * Called when we have an active connection to a target on the bus, + * this function finds the nearest period to the input period limited + * by the capabilities of the bus connectivity of and sync settings for + * the target. + */ +static void +ahd_devlimited_syncrate(struct ahd_softc *ahd, + struct ahd_initiator_tinfo *tinfo, + u_int *period, u_int *ppr_options, role_t role) +{ + struct ahd_transinfo *transinfo; + u_int maxsync; + + if ((ahd_inb(ahd, SBLKCTL) & ENAB40) != 0 + && (ahd_inb(ahd, SSTAT2) & EXP_ACTIVE) == 0) { + maxsync = AHD_SYNCRATE_PACED; + } else { + maxsync = AHD_SYNCRATE_ULTRA; + /* Can't do DT related options on an SE bus */ + *ppr_options &= MSG_EXT_PPR_QAS_REQ; + } + /* + * Never allow a value higher than our current goal + * period otherwise we may allow a target initiated + * negotiation to go above the limit as set by the + * user. In the case of an initiator initiated + * sync negotiation, we limit based on the user + * setting. This allows the system to still accept + * incoming negotiations even if target initiated + * negotiation is not performed. + */ + if (role == ROLE_TARGET) + transinfo = &tinfo->user; + else + transinfo = &tinfo->goal; + *ppr_options &= (transinfo->ppr_options|MSG_EXT_PPR_PCOMP_EN); + if (transinfo->width == MSG_EXT_WDTR_BUS_8_BIT) { + maxsync = max(maxsync, (u_int)AHD_SYNCRATE_ULTRA2); + *ppr_options &= ~MSG_EXT_PPR_DT_REQ; + } + if (transinfo->period == 0) { + *period = 0; + *ppr_options = 0; + } else { + *period = max(*period, (u_int)transinfo->period); + ahd_find_syncrate(ahd, period, ppr_options, maxsync); + } +} + +/* + * Look up the valid period to SCSIRATE conversion in our table. + * Return the period and offset that should be sent to the target + * if this was the beginning of an SDTR. + */ +void +ahd_find_syncrate(struct ahd_softc *ahd, u_int *period, + u_int *ppr_options, u_int maxsync) +{ + if (*period < maxsync) + *period = maxsync; + + if ((*ppr_options & MSG_EXT_PPR_DT_REQ) != 0 + && *period > AHD_SYNCRATE_MIN_DT) + *ppr_options &= ~MSG_EXT_PPR_DT_REQ; + + if (*period > AHD_SYNCRATE_MIN) + *period = 0; + + /* Honor PPR option conformance rules. */ + if (*period > AHD_SYNCRATE_PACED) + *ppr_options &= ~MSG_EXT_PPR_RTI; + + if ((*ppr_options & MSG_EXT_PPR_IU_REQ) == 0) + *ppr_options &= (MSG_EXT_PPR_DT_REQ|MSG_EXT_PPR_QAS_REQ); + + if ((*ppr_options & MSG_EXT_PPR_DT_REQ) == 0) + *ppr_options &= MSG_EXT_PPR_QAS_REQ; + + /* Skip all PACED only entries if IU is not available */ + if ((*ppr_options & MSG_EXT_PPR_IU_REQ) == 0 + && *period < AHD_SYNCRATE_DT) + *period = AHD_SYNCRATE_DT; + + /* Skip all DT only entries if DT is not available */ + if ((*ppr_options & MSG_EXT_PPR_DT_REQ) == 0 + && *period < AHD_SYNCRATE_ULTRA2) + *period = AHD_SYNCRATE_ULTRA2; +} + +/* + * Truncate the given synchronous offset to a value the + * current adapter type and syncrate are capable of. + */ +static void +ahd_validate_offset(struct ahd_softc *ahd, + struct ahd_initiator_tinfo *tinfo, + u_int period, u_int *offset, int wide, + role_t role) +{ + u_int maxoffset; + + /* Limit offset to what we can do */ + if (period == 0) + maxoffset = 0; + else if (period <= AHD_SYNCRATE_PACED) { + if ((ahd->bugs & AHD_PACED_NEGTABLE_BUG) != 0) + maxoffset = MAX_OFFSET_PACED_BUG; + else + maxoffset = MAX_OFFSET_PACED; + } else + maxoffset = MAX_OFFSET_NON_PACED; + *offset = min(*offset, maxoffset); + if (tinfo != NULL) { + if (role == ROLE_TARGET) + *offset = min(*offset, (u_int)tinfo->user.offset); + else + *offset = min(*offset, (u_int)tinfo->goal.offset); + } +} + +/* + * Truncate the given transfer width parameter to a value the + * current adapter type is capable of. + */ +static void +ahd_validate_width(struct ahd_softc *ahd, struct ahd_initiator_tinfo *tinfo, + u_int *bus_width, role_t role) +{ + switch (*bus_width) { + default: + if (ahd->features & AHD_WIDE) { + /* Respond Wide */ + *bus_width = MSG_EXT_WDTR_BUS_16_BIT; + break; + } + fallthrough; + case MSG_EXT_WDTR_BUS_8_BIT: + *bus_width = MSG_EXT_WDTR_BUS_8_BIT; + break; + } + if (tinfo != NULL) { + if (role == ROLE_TARGET) + *bus_width = min((u_int)tinfo->user.width, *bus_width); + else + *bus_width = min((u_int)tinfo->goal.width, *bus_width); + } +} + +/* + * Update the bitmask of targets for which the controller should + * negotiate with at the next convenient opportunity. This currently + * means the next time we send the initial identify messages for + * a new transaction. + */ +int +ahd_update_neg_request(struct ahd_softc *ahd, struct ahd_devinfo *devinfo, + struct ahd_tmode_tstate *tstate, + struct ahd_initiator_tinfo *tinfo, ahd_neg_type neg_type) +{ + u_int auto_negotiate_orig; + + auto_negotiate_orig = tstate->auto_negotiate; + if (neg_type == AHD_NEG_ALWAYS) { + /* + * Force our "current" settings to be + * unknown so that unless a bus reset + * occurs the need to renegotiate is + * recorded persistently. + */ + if ((ahd->features & AHD_WIDE) != 0) + tinfo->curr.width = AHD_WIDTH_UNKNOWN; + tinfo->curr.period = AHD_PERIOD_UNKNOWN; + tinfo->curr.offset = AHD_OFFSET_UNKNOWN; + } + if (tinfo->curr.period != tinfo->goal.period + || tinfo->curr.width != tinfo->goal.width + || tinfo->curr.offset != tinfo->goal.offset + || tinfo->curr.ppr_options != tinfo->goal.ppr_options + || (neg_type == AHD_NEG_IF_NON_ASYNC + && (tinfo->goal.offset != 0 + || tinfo->goal.width != MSG_EXT_WDTR_BUS_8_BIT + || tinfo->goal.ppr_options != 0))) + tstate->auto_negotiate |= devinfo->target_mask; + else + tstate->auto_negotiate &= ~devinfo->target_mask; + + return (auto_negotiate_orig != tstate->auto_negotiate); +} + +/* + * Update the user/goal/curr tables of synchronous negotiation + * parameters as well as, in the case of a current or active update, + * any data structures on the host controller. In the case of an + * active update, the specified target is currently talking to us on + * the bus, so the transfer parameter update must take effect + * immediately. + */ +void +ahd_set_syncrate(struct ahd_softc *ahd, struct ahd_devinfo *devinfo, + u_int period, u_int offset, u_int ppr_options, + u_int type, int paused) +{ + struct ahd_initiator_tinfo *tinfo; + struct ahd_tmode_tstate *tstate; + u_int old_period; + u_int old_offset; + u_int old_ppr; + int active; + int update_needed; + + active = (type & AHD_TRANS_ACTIVE) == AHD_TRANS_ACTIVE; + update_needed = 0; + + if (period == 0 || offset == 0) { + period = 0; + offset = 0; + } + + tinfo = ahd_fetch_transinfo(ahd, devinfo->channel, devinfo->our_scsiid, + devinfo->target, &tstate); + + if ((type & AHD_TRANS_USER) != 0) { + tinfo->user.period = period; + tinfo->user.offset = offset; + tinfo->user.ppr_options = ppr_options; + } + + if ((type & AHD_TRANS_GOAL) != 0) { + tinfo->goal.period = period; + tinfo->goal.offset = offset; + tinfo->goal.ppr_options = ppr_options; + } + + old_period = tinfo->curr.period; + old_offset = tinfo->curr.offset; + old_ppr = tinfo->curr.ppr_options; + + if ((type & AHD_TRANS_CUR) != 0 + && (old_period != period + || old_offset != offset + || old_ppr != ppr_options)) { + + update_needed++; + + tinfo->curr.period = period; + tinfo->curr.offset = offset; + tinfo->curr.ppr_options = ppr_options; + + ahd_send_async(ahd, devinfo->channel, devinfo->target, + CAM_LUN_WILDCARD, AC_TRANSFER_NEG); + if (bootverbose) { + if (offset != 0) { + int options; + + printk("%s: target %d synchronous with " + "period = 0x%x, offset = 0x%x", + ahd_name(ahd), devinfo->target, + period, offset); + options = 0; + if ((ppr_options & MSG_EXT_PPR_RD_STRM) != 0) { + printk("(RDSTRM"); + options++; + } + if ((ppr_options & MSG_EXT_PPR_DT_REQ) != 0) { + printk("%s", options ? "|DT" : "(DT"); + options++; + } + if ((ppr_options & MSG_EXT_PPR_IU_REQ) != 0) { + printk("%s", options ? "|IU" : "(IU"); + options++; + } + if ((ppr_options & MSG_EXT_PPR_RTI) != 0) { + printk("%s", options ? "|RTI" : "(RTI"); + options++; + } + if ((ppr_options & MSG_EXT_PPR_QAS_REQ) != 0) { + printk("%s", options ? "|QAS" : "(QAS"); + options++; + } + if (options != 0) + printk(")\n"); + else + printk("\n"); + } else { + printk("%s: target %d using " + "asynchronous transfers%s\n", + ahd_name(ahd), devinfo->target, + (ppr_options & MSG_EXT_PPR_QAS_REQ) != 0 + ? "(QAS)" : ""); + } + } + } + /* + * Always refresh the neg-table to handle the case of the + * sequencer setting the ENATNO bit for a MK_MESSAGE request. + * We will always renegotiate in that case if this is a + * packetized request. Also manage the busfree expected flag + * from this common routine so that we catch changes due to + * WDTR or SDTR messages. + */ + if ((type & AHD_TRANS_CUR) != 0) { + if (!paused) + ahd_pause(ahd); + ahd_update_neg_table(ahd, devinfo, &tinfo->curr); + if (!paused) + ahd_unpause(ahd); + if (ahd->msg_type != MSG_TYPE_NONE) { + if ((old_ppr & MSG_EXT_PPR_IU_REQ) + != (ppr_options & MSG_EXT_PPR_IU_REQ)) { +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) { + ahd_print_devinfo(ahd, devinfo); + printk("Expecting IU Change busfree\n"); + } +#endif + ahd->msg_flags |= MSG_FLAG_EXPECT_PPR_BUSFREE + | MSG_FLAG_IU_REQ_CHANGED; + } + if ((old_ppr & MSG_EXT_PPR_IU_REQ) != 0) { +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) + printk("PPR with IU_REQ outstanding\n"); +#endif + ahd->msg_flags |= MSG_FLAG_EXPECT_PPR_BUSFREE; + } + } + } + + update_needed += ahd_update_neg_request(ahd, devinfo, tstate, + tinfo, AHD_NEG_TO_GOAL); + + if (update_needed && active) + ahd_update_pending_scbs(ahd); +} + +/* + * Update the user/goal/curr tables of wide negotiation + * parameters as well as, in the case of a current or active update, + * any data structures on the host controller. In the case of an + * active update, the specified target is currently talking to us on + * the bus, so the transfer parameter update must take effect + * immediately. + */ +void +ahd_set_width(struct ahd_softc *ahd, struct ahd_devinfo *devinfo, + u_int width, u_int type, int paused) +{ + struct ahd_initiator_tinfo *tinfo; + struct ahd_tmode_tstate *tstate; + u_int oldwidth; + int active; + int update_needed; + + active = (type & AHD_TRANS_ACTIVE) == AHD_TRANS_ACTIVE; + update_needed = 0; + tinfo = ahd_fetch_transinfo(ahd, devinfo->channel, devinfo->our_scsiid, + devinfo->target, &tstate); + + if ((type & AHD_TRANS_USER) != 0) + tinfo->user.width = width; + + if ((type & AHD_TRANS_GOAL) != 0) + tinfo->goal.width = width; + + oldwidth = tinfo->curr.width; + if ((type & AHD_TRANS_CUR) != 0 && oldwidth != width) { + + update_needed++; + + tinfo->curr.width = width; + ahd_send_async(ahd, devinfo->channel, devinfo->target, + CAM_LUN_WILDCARD, AC_TRANSFER_NEG); + if (bootverbose) { + printk("%s: target %d using %dbit transfers\n", + ahd_name(ahd), devinfo->target, + 8 * (0x01 << width)); + } + } + + if ((type & AHD_TRANS_CUR) != 0) { + if (!paused) + ahd_pause(ahd); + ahd_update_neg_table(ahd, devinfo, &tinfo->curr); + if (!paused) + ahd_unpause(ahd); + } + + update_needed += ahd_update_neg_request(ahd, devinfo, tstate, + tinfo, AHD_NEG_TO_GOAL); + if (update_needed && active) + ahd_update_pending_scbs(ahd); + +} + +/* + * Update the current state of tagged queuing for a given target. + */ +static void +ahd_set_tags(struct ahd_softc *ahd, struct scsi_cmnd *cmd, + struct ahd_devinfo *devinfo, ahd_queue_alg alg) +{ + struct scsi_device *sdev = cmd->device; + + ahd_platform_set_tags(ahd, sdev, devinfo, alg); + ahd_send_async(ahd, devinfo->channel, devinfo->target, + devinfo->lun, AC_TRANSFER_NEG); +} + +static void +ahd_update_neg_table(struct ahd_softc *ahd, struct ahd_devinfo *devinfo, + struct ahd_transinfo *tinfo) +{ + ahd_mode_state saved_modes; + u_int period; + u_int ppr_opts; + u_int con_opts; + u_int offset; + u_int saved_negoaddr; + uint8_t iocell_opts[sizeof(ahd->iocell_opts)]; + + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + + saved_negoaddr = ahd_inb(ahd, NEGOADDR); + ahd_outb(ahd, NEGOADDR, devinfo->target); + period = tinfo->period; + offset = tinfo->offset; + memcpy(iocell_opts, ahd->iocell_opts, sizeof(ahd->iocell_opts)); + ppr_opts = tinfo->ppr_options & (MSG_EXT_PPR_QAS_REQ|MSG_EXT_PPR_DT_REQ + |MSG_EXT_PPR_IU_REQ|MSG_EXT_PPR_RTI); + con_opts = 0; + if (period == 0) + period = AHD_SYNCRATE_ASYNC; + if (period == AHD_SYNCRATE_160) { + + if ((ahd->bugs & AHD_PACED_NEGTABLE_BUG) != 0) { + /* + * When the SPI4 spec was finalized, PACE transfers + * was not made a configurable option in the PPR + * message. Instead it is assumed to be enabled for + * any syncrate faster than 80MHz. Nevertheless, + * Harpoon2A4 allows this to be configurable. + * + * Harpoon2A4 also assumes at most 2 data bytes per + * negotiated REQ/ACK offset. Paced transfers take + * 4, so we must adjust our offset. + */ + ppr_opts |= PPROPT_PACE; + offset *= 2; + + /* + * Harpoon2A assumed that there would be a + * fallback rate between 160MHz and 80MHz, + * so 7 is used as the period factor rather + * than 8 for 160MHz. + */ + period = AHD_SYNCRATE_REVA_160; + } + if ((tinfo->ppr_options & MSG_EXT_PPR_PCOMP_EN) == 0) + iocell_opts[AHD_PRECOMP_SLEW_INDEX] &= + ~AHD_PRECOMP_MASK; + } else { + /* + * Precomp should be disabled for non-paced transfers. + */ + iocell_opts[AHD_PRECOMP_SLEW_INDEX] &= ~AHD_PRECOMP_MASK; + + if ((ahd->features & AHD_NEW_IOCELL_OPTS) != 0 + && (ppr_opts & MSG_EXT_PPR_DT_REQ) != 0 + && (ppr_opts & MSG_EXT_PPR_IU_REQ) == 0) { + /* + * Slow down our CRC interval to be + * compatible with non-packetized + * U160 devices that can't handle a + * CRC at full speed. + */ + con_opts |= ENSLOWCRC; + } + + if ((ahd->bugs & AHD_PACED_NEGTABLE_BUG) != 0) { + /* + * On H2A4, revert to a slower slewrate + * on non-paced transfers. + */ + iocell_opts[AHD_PRECOMP_SLEW_INDEX] &= + ~AHD_SLEWRATE_MASK; + } + } + + ahd_outb(ahd, ANNEXCOL, AHD_ANNEXCOL_PRECOMP_SLEW); + ahd_outb(ahd, ANNEXDAT, iocell_opts[AHD_PRECOMP_SLEW_INDEX]); + ahd_outb(ahd, ANNEXCOL, AHD_ANNEXCOL_AMPLITUDE); + ahd_outb(ahd, ANNEXDAT, iocell_opts[AHD_AMPLITUDE_INDEX]); + + ahd_outb(ahd, NEGPERIOD, period); + ahd_outb(ahd, NEGPPROPTS, ppr_opts); + ahd_outb(ahd, NEGOFFSET, offset); + + if (tinfo->width == MSG_EXT_WDTR_BUS_16_BIT) + con_opts |= WIDEXFER; + + /* + * Slow down our CRC interval to be + * compatible with packetized U320 devices + * that can't handle a CRC at full speed + */ + if (ahd->features & AHD_AIC79XXB_SLOWCRC) { + con_opts |= ENSLOWCRC; + } + + /* + * During packetized transfers, the target will + * give us the opportunity to send command packets + * without us asserting attention. + */ + if ((tinfo->ppr_options & MSG_EXT_PPR_IU_REQ) == 0) + con_opts |= ENAUTOATNO; + ahd_outb(ahd, NEGCONOPTS, con_opts); + ahd_outb(ahd, NEGOADDR, saved_negoaddr); + ahd_restore_modes(ahd, saved_modes); +} + +/* + * When the transfer settings for a connection change, setup for + * negotiation in pending SCBs to effect the change as quickly as + * possible. We also cancel any negotiations that are scheduled + * for inflight SCBs that have not been started yet. + */ +static void +ahd_update_pending_scbs(struct ahd_softc *ahd) +{ + struct scb *pending_scb; + int pending_scb_count; + int paused; + u_int saved_scbptr; + ahd_mode_state saved_modes; + + /* + * Traverse the pending SCB list and ensure that all of the + * SCBs there have the proper settings. We can only safely + * clear the negotiation required flag (setting requires the + * execution queue to be modified) and this is only possible + * if we are not already attempting to select out for this + * SCB. For this reason, all callers only call this routine + * if we are changing the negotiation settings for the currently + * active transaction on the bus. + */ + pending_scb_count = 0; + LIST_FOREACH(pending_scb, &ahd->pending_scbs, pending_links) { + struct ahd_devinfo devinfo; + struct ahd_tmode_tstate *tstate; + + ahd_scb_devinfo(ahd, &devinfo, pending_scb); + ahd_fetch_transinfo(ahd, devinfo.channel, devinfo.our_scsiid, + devinfo.target, &tstate); + if ((tstate->auto_negotiate & devinfo.target_mask) == 0 + && (pending_scb->flags & SCB_AUTO_NEGOTIATE) != 0) { + pending_scb->flags &= ~SCB_AUTO_NEGOTIATE; + pending_scb->hscb->control &= ~MK_MESSAGE; + } + ahd_sync_scb(ahd, pending_scb, + BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); + pending_scb_count++; + } + + if (pending_scb_count == 0) + return; + + if (ahd_is_paused(ahd)) { + paused = 1; + } else { + paused = 0; + ahd_pause(ahd); + } + + /* + * Force the sequencer to reinitialize the selection for + * the command at the head of the execution queue if it + * has already been setup. The negotiation changes may + * effect whether we select-out with ATN. It is only + * safe to clear ENSELO when the bus is not free and no + * selection is in progres or completed. + */ + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + if ((ahd_inb(ahd, SCSISIGI) & BSYI) != 0 + && (ahd_inb(ahd, SSTAT0) & (SELDO|SELINGO)) == 0) + ahd_outb(ahd, SCSISEQ0, ahd_inb(ahd, SCSISEQ0) & ~ENSELO); + saved_scbptr = ahd_get_scbptr(ahd); + /* Ensure that the hscbs down on the card match the new information */ + LIST_FOREACH(pending_scb, &ahd->pending_scbs, pending_links) { + u_int scb_tag; + u_int control; + + scb_tag = SCB_GET_TAG(pending_scb); + ahd_set_scbptr(ahd, scb_tag); + control = ahd_inb_scbram(ahd, SCB_CONTROL); + control &= ~MK_MESSAGE; + control |= pending_scb->hscb->control & MK_MESSAGE; + ahd_outb(ahd, SCB_CONTROL, control); + } + ahd_set_scbptr(ahd, saved_scbptr); + ahd_restore_modes(ahd, saved_modes); + + if (paused == 0) + ahd_unpause(ahd); +} + +/**************************** Pathing Information *****************************/ +static void +ahd_fetch_devinfo(struct ahd_softc *ahd, struct ahd_devinfo *devinfo) +{ + ahd_mode_state saved_modes; + u_int saved_scsiid; + role_t role; + int our_id; + + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + + if (ahd_inb(ahd, SSTAT0) & TARGET) + role = ROLE_TARGET; + else + role = ROLE_INITIATOR; + + if (role == ROLE_TARGET + && (ahd_inb(ahd, SEQ_FLAGS) & CMDPHASE_PENDING) != 0) { + /* We were selected, so pull our id from TARGIDIN */ + our_id = ahd_inb(ahd, TARGIDIN) & OID; + } else if (role == ROLE_TARGET) + our_id = ahd_inb(ahd, TOWNID); + else + our_id = ahd_inb(ahd, IOWNID); + + saved_scsiid = ahd_inb(ahd, SAVED_SCSIID); + ahd_compile_devinfo(devinfo, + our_id, + SCSIID_TARGET(ahd, saved_scsiid), + ahd_inb(ahd, SAVED_LUN), + SCSIID_CHANNEL(ahd, saved_scsiid), + role); + ahd_restore_modes(ahd, saved_modes); +} + +void +ahd_print_devinfo(struct ahd_softc *ahd, struct ahd_devinfo *devinfo) +{ + printk("%s:%c:%d:%d: ", ahd_name(ahd), 'A', + devinfo->target, devinfo->lun); +} + +static const struct ahd_phase_table_entry* +ahd_lookup_phase_entry(int phase) +{ + const struct ahd_phase_table_entry *entry; + const struct ahd_phase_table_entry *last_entry; + + /* + * num_phases doesn't include the default entry which + * will be returned if the phase doesn't match. + */ + last_entry = &ahd_phase_table[num_phases]; + for (entry = ahd_phase_table; entry < last_entry; entry++) { + if (phase == entry->phase) + break; + } + return (entry); +} + +void +ahd_compile_devinfo(struct ahd_devinfo *devinfo, u_int our_id, u_int target, + u_int lun, char channel, role_t role) +{ + devinfo->our_scsiid = our_id; + devinfo->target = target; + devinfo->lun = lun; + devinfo->target_offset = target; + devinfo->channel = channel; + devinfo->role = role; + if (channel == 'B') + devinfo->target_offset += 8; + devinfo->target_mask = (0x01 << devinfo->target_offset); +} + +static void +ahd_scb_devinfo(struct ahd_softc *ahd, struct ahd_devinfo *devinfo, + struct scb *scb) +{ + role_t role; + int our_id; + + our_id = SCSIID_OUR_ID(scb->hscb->scsiid); + role = ROLE_INITIATOR; + if ((scb->hscb->control & TARGET_SCB) != 0) + role = ROLE_TARGET; + ahd_compile_devinfo(devinfo, our_id, SCB_GET_TARGET(ahd, scb), + SCB_GET_LUN(scb), SCB_GET_CHANNEL(ahd, scb), role); +} + + +/************************ Message Phase Processing ****************************/ +/* + * When an initiator transaction with the MK_MESSAGE flag either reconnects + * or enters the initial message out phase, we are interrupted. Fill our + * outgoing message buffer with the appropriate message and beging handing + * the message phase(s) manually. + */ +static void +ahd_setup_initiator_msgout(struct ahd_softc *ahd, struct ahd_devinfo *devinfo, + struct scb *scb) +{ + /* + * To facilitate adding multiple messages together, + * each routine should increment the index and len + * variables instead of setting them explicitly. + */ + ahd->msgout_index = 0; + ahd->msgout_len = 0; + + if (ahd_currently_packetized(ahd)) + ahd->msg_flags |= MSG_FLAG_PACKETIZED; + + if (ahd->send_msg_perror + && ahd_inb(ahd, MSG_OUT) == HOST_MSG) { + ahd->msgout_buf[ahd->msgout_index++] = ahd->send_msg_perror; + ahd->msgout_len++; + ahd->msg_type = MSG_TYPE_INITIATOR_MSGOUT; +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) + printk("Setting up for Parity Error delivery\n"); +#endif + return; + } else if (scb == NULL) { + printk("%s: WARNING. No pending message for " + "I_T msgin. Issuing NO-OP\n", ahd_name(ahd)); + ahd->msgout_buf[ahd->msgout_index++] = MSG_NOOP; + ahd->msgout_len++; + ahd->msg_type = MSG_TYPE_INITIATOR_MSGOUT; + return; + } + + if ((scb->flags & SCB_DEVICE_RESET) == 0 + && (scb->flags & SCB_PACKETIZED) == 0 + && ahd_inb(ahd, MSG_OUT) == MSG_IDENTIFYFLAG) { + u_int identify_msg; + + identify_msg = MSG_IDENTIFYFLAG | SCB_GET_LUN(scb); + if ((scb->hscb->control & DISCENB) != 0) + identify_msg |= MSG_IDENTIFY_DISCFLAG; + ahd->msgout_buf[ahd->msgout_index++] = identify_msg; + ahd->msgout_len++; + + if ((scb->hscb->control & TAG_ENB) != 0) { + ahd->msgout_buf[ahd->msgout_index++] = + scb->hscb->control & (TAG_ENB|SCB_TAG_TYPE); + ahd->msgout_buf[ahd->msgout_index++] = SCB_GET_TAG(scb); + ahd->msgout_len += 2; + } + } + + if (scb->flags & SCB_DEVICE_RESET) { + ahd->msgout_buf[ahd->msgout_index++] = MSG_BUS_DEV_RESET; + ahd->msgout_len++; + ahd_print_path(ahd, scb); + printk("Bus Device Reset Message Sent\n"); + /* + * Clear our selection hardware in advance of + * the busfree. We may have an entry in the waiting + * Q for this target, and we don't want to go about + * selecting while we handle the busfree and blow it + * away. + */ + ahd_outb(ahd, SCSISEQ0, 0); + } else if ((scb->flags & SCB_ABORT) != 0) { + + if ((scb->hscb->control & TAG_ENB) != 0) { + ahd->msgout_buf[ahd->msgout_index++] = MSG_ABORT_TAG; + } else { + ahd->msgout_buf[ahd->msgout_index++] = MSG_ABORT; + } + ahd->msgout_len++; + ahd_print_path(ahd, scb); + printk("Abort%s Message Sent\n", + (scb->hscb->control & TAG_ENB) != 0 ? " Tag" : ""); + /* + * Clear our selection hardware in advance of + * the busfree. We may have an entry in the waiting + * Q for this target, and we don't want to go about + * selecting while we handle the busfree and blow it + * away. + */ + ahd_outb(ahd, SCSISEQ0, 0); + } else if ((scb->flags & (SCB_AUTO_NEGOTIATE|SCB_NEGOTIATE)) != 0) { + ahd_build_transfer_msg(ahd, devinfo); + /* + * Clear our selection hardware in advance of potential + * PPR IU status change busfree. We may have an entry in + * the waiting Q for this target, and we don't want to go + * about selecting while we handle the busfree and blow + * it away. + */ + ahd_outb(ahd, SCSISEQ0, 0); + } else { + printk("ahd_intr: AWAITING_MSG for an SCB that " + "does not have a waiting message\n"); + printk("SCSIID = %x, target_mask = %x\n", scb->hscb->scsiid, + devinfo->target_mask); + panic("SCB = %d, SCB Control = %x:%x, MSG_OUT = %x " + "SCB flags = %x", SCB_GET_TAG(scb), scb->hscb->control, + ahd_inb_scbram(ahd, SCB_CONTROL), ahd_inb(ahd, MSG_OUT), + scb->flags); + } + + /* + * Clear the MK_MESSAGE flag from the SCB so we aren't + * asked to send this message again. + */ + ahd_outb(ahd, SCB_CONTROL, + ahd_inb_scbram(ahd, SCB_CONTROL) & ~MK_MESSAGE); + scb->hscb->control &= ~MK_MESSAGE; + ahd->msgout_index = 0; + ahd->msg_type = MSG_TYPE_INITIATOR_MSGOUT; +} + +/* + * Build an appropriate transfer negotiation message for the + * currently active target. + */ +static void +ahd_build_transfer_msg(struct ahd_softc *ahd, struct ahd_devinfo *devinfo) +{ + /* + * We need to initiate transfer negotiations. + * If our current and goal settings are identical, + * we want to renegotiate due to a check condition. + */ + struct ahd_initiator_tinfo *tinfo; + struct ahd_tmode_tstate *tstate; + int dowide; + int dosync; + int doppr; + u_int period; + u_int ppr_options; + u_int offset; + + tinfo = ahd_fetch_transinfo(ahd, devinfo->channel, devinfo->our_scsiid, + devinfo->target, &tstate); + /* + * Filter our period based on the current connection. + * If we can't perform DT transfers on this segment (not in LVD + * mode for instance), then our decision to issue a PPR message + * may change. + */ + period = tinfo->goal.period; + offset = tinfo->goal.offset; + ppr_options = tinfo->goal.ppr_options; + /* Target initiated PPR is not allowed in the SCSI spec */ + if (devinfo->role == ROLE_TARGET) + ppr_options = 0; + ahd_devlimited_syncrate(ahd, tinfo, &period, + &ppr_options, devinfo->role); + dowide = tinfo->curr.width != tinfo->goal.width; + dosync = tinfo->curr.offset != offset || tinfo->curr.period != period; + /* + * Only use PPR if we have options that need it, even if the device + * claims to support it. There might be an expander in the way + * that doesn't. + */ + doppr = ppr_options != 0; + + if (!dowide && !dosync && !doppr) { + dowide = tinfo->goal.width != MSG_EXT_WDTR_BUS_8_BIT; + dosync = tinfo->goal.offset != 0; + } + + if (!dowide && !dosync && !doppr) { + /* + * Force async with a WDTR message if we have a wide bus, + * or just issue an SDTR with a 0 offset. + */ + if ((ahd->features & AHD_WIDE) != 0) + dowide = 1; + else + dosync = 1; + + if (bootverbose) { + ahd_print_devinfo(ahd, devinfo); + printk("Ensuring async\n"); + } + } + /* Target initiated PPR is not allowed in the SCSI spec */ + if (devinfo->role == ROLE_TARGET) + doppr = 0; + + /* + * Both the PPR message and SDTR message require the + * goal syncrate to be limited to what the target device + * is capable of handling (based on whether an LVD->SE + * expander is on the bus), so combine these two cases. + * Regardless, guarantee that if we are using WDTR and SDTR + * messages that WDTR comes first. + */ + if (doppr || (dosync && !dowide)) { + + offset = tinfo->goal.offset; + ahd_validate_offset(ahd, tinfo, period, &offset, + doppr ? tinfo->goal.width + : tinfo->curr.width, + devinfo->role); + if (doppr) { + ahd_construct_ppr(ahd, devinfo, period, offset, + tinfo->goal.width, ppr_options); + } else { + ahd_construct_sdtr(ahd, devinfo, period, offset); + } + } else { + ahd_construct_wdtr(ahd, devinfo, tinfo->goal.width); + } +} + +/* + * Build a synchronous negotiation message in our message + * buffer based on the input parameters. + */ +static void +ahd_construct_sdtr(struct ahd_softc *ahd, struct ahd_devinfo *devinfo, + u_int period, u_int offset) +{ + if (offset == 0) + period = AHD_ASYNC_XFER_PERIOD; + ahd->msgout_index += spi_populate_sync_msg( + ahd->msgout_buf + ahd->msgout_index, period, offset); + ahd->msgout_len += 5; + if (bootverbose) { + printk("(%s:%c:%d:%d): Sending SDTR period %x, offset %x\n", + ahd_name(ahd), devinfo->channel, devinfo->target, + devinfo->lun, period, offset); + } +} + +/* + * Build a wide negotiateion message in our message + * buffer based on the input parameters. + */ +static void +ahd_construct_wdtr(struct ahd_softc *ahd, struct ahd_devinfo *devinfo, + u_int bus_width) +{ + ahd->msgout_index += spi_populate_width_msg( + ahd->msgout_buf + ahd->msgout_index, bus_width); + ahd->msgout_len += 4; + if (bootverbose) { + printk("(%s:%c:%d:%d): Sending WDTR %x\n", + ahd_name(ahd), devinfo->channel, devinfo->target, + devinfo->lun, bus_width); + } +} + +/* + * Build a parallel protocol request message in our message + * buffer based on the input parameters. + */ +static void +ahd_construct_ppr(struct ahd_softc *ahd, struct ahd_devinfo *devinfo, + u_int period, u_int offset, u_int bus_width, + u_int ppr_options) +{ + /* + * Always request precompensation from + * the other target if we are running + * at paced syncrates. + */ + if (period <= AHD_SYNCRATE_PACED) + ppr_options |= MSG_EXT_PPR_PCOMP_EN; + if (offset == 0) + period = AHD_ASYNC_XFER_PERIOD; + ahd->msgout_index += spi_populate_ppr_msg( + ahd->msgout_buf + ahd->msgout_index, period, offset, + bus_width, ppr_options); + ahd->msgout_len += 8; + if (bootverbose) { + printk("(%s:%c:%d:%d): Sending PPR bus_width %x, period %x, " + "offset %x, ppr_options %x\n", ahd_name(ahd), + devinfo->channel, devinfo->target, devinfo->lun, + bus_width, period, offset, ppr_options); + } +} + +/* + * Clear any active message state. + */ +static void +ahd_clear_msg_state(struct ahd_softc *ahd) +{ + ahd_mode_state saved_modes; + + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + ahd->send_msg_perror = 0; + ahd->msg_flags = MSG_FLAG_NONE; + ahd->msgout_len = 0; + ahd->msgin_index = 0; + ahd->msg_type = MSG_TYPE_NONE; + if ((ahd_inb(ahd, SCSISIGO) & ATNO) != 0) { + /* + * The target didn't care to respond to our + * message request, so clear ATN. + */ + ahd_outb(ahd, CLRSINT1, CLRATNO); + } + ahd_outb(ahd, MSG_OUT, MSG_NOOP); + ahd_outb(ahd, SEQ_FLAGS2, + ahd_inb(ahd, SEQ_FLAGS2) & ~TARGET_MSG_PENDING); + ahd_restore_modes(ahd, saved_modes); +} + +/* + * Manual message loop handler. + */ +static void +ahd_handle_message_phase(struct ahd_softc *ahd) +{ + struct ahd_devinfo devinfo; + u_int bus_phase; + int end_session; + + ahd_fetch_devinfo(ahd, &devinfo); + end_session = FALSE; + bus_phase = ahd_inb(ahd, LASTPHASE); + + if ((ahd_inb(ahd, LQISTAT2) & LQIPHASE_OUTPKT) != 0) { + printk("LQIRETRY for LQIPHASE_OUTPKT\n"); + ahd_outb(ahd, LQCTL2, LQIRETRY); + } +reswitch: + switch (ahd->msg_type) { + case MSG_TYPE_INITIATOR_MSGOUT: + { + int lastbyte; + int phasemis; + int msgdone; + + if (ahd->msgout_len == 0 && ahd->send_msg_perror == 0) + panic("HOST_MSG_LOOP interrupt with no active message"); + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) { + ahd_print_devinfo(ahd, &devinfo); + printk("INITIATOR_MSG_OUT"); + } +#endif + phasemis = bus_phase != P_MESGOUT; + if (phasemis) { +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) { + printk(" PHASEMIS %s\n", + ahd_lookup_phase_entry(bus_phase) + ->phasemsg); + } +#endif + if (bus_phase == P_MESGIN) { + /* + * Change gears and see if + * this messages is of interest to + * us or should be passed back to + * the sequencer. + */ + ahd_outb(ahd, CLRSINT1, CLRATNO); + ahd->send_msg_perror = 0; + ahd->msg_type = MSG_TYPE_INITIATOR_MSGIN; + ahd->msgin_index = 0; + goto reswitch; + } + end_session = TRUE; + break; + } + + if (ahd->send_msg_perror) { + ahd_outb(ahd, CLRSINT1, CLRATNO); + ahd_outb(ahd, CLRSINT1, CLRREQINIT); +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) + printk(" byte 0x%x\n", ahd->send_msg_perror); +#endif + /* + * If we are notifying the target of a CRC error + * during packetized operations, the target is + * within its rights to acknowledge our message + * with a busfree. + */ + if ((ahd->msg_flags & MSG_FLAG_PACKETIZED) != 0 + && ahd->send_msg_perror == MSG_INITIATOR_DET_ERR) + ahd->msg_flags |= MSG_FLAG_EXPECT_IDE_BUSFREE; + + ahd_outb(ahd, RETURN_2, ahd->send_msg_perror); + ahd_outb(ahd, RETURN_1, CONT_MSG_LOOP_WRITE); + break; + } + + msgdone = ahd->msgout_index == ahd->msgout_len; + if (msgdone) { + /* + * The target has requested a retry. + * Re-assert ATN, reset our message index to + * 0, and try again. + */ + ahd->msgout_index = 0; + ahd_assert_atn(ahd); + } + + lastbyte = ahd->msgout_index == (ahd->msgout_len - 1); + if (lastbyte) { + /* Last byte is signified by dropping ATN */ + ahd_outb(ahd, CLRSINT1, CLRATNO); + } + + /* + * Clear our interrupt status and present + * the next byte on the bus. + */ + ahd_outb(ahd, CLRSINT1, CLRREQINIT); +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) + printk(" byte 0x%x\n", + ahd->msgout_buf[ahd->msgout_index]); +#endif + ahd_outb(ahd, RETURN_2, ahd->msgout_buf[ahd->msgout_index++]); + ahd_outb(ahd, RETURN_1, CONT_MSG_LOOP_WRITE); + break; + } + case MSG_TYPE_INITIATOR_MSGIN: + { + int phasemis; + int message_done; + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) { + ahd_print_devinfo(ahd, &devinfo); + printk("INITIATOR_MSG_IN"); + } +#endif + phasemis = bus_phase != P_MESGIN; + if (phasemis) { +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) { + printk(" PHASEMIS %s\n", + ahd_lookup_phase_entry(bus_phase) + ->phasemsg); + } +#endif + ahd->msgin_index = 0; + if (bus_phase == P_MESGOUT + && (ahd->send_msg_perror != 0 + || (ahd->msgout_len != 0 + && ahd->msgout_index == 0))) { + ahd->msg_type = MSG_TYPE_INITIATOR_MSGOUT; + goto reswitch; + } + end_session = TRUE; + break; + } + + /* Pull the byte in without acking it */ + ahd->msgin_buf[ahd->msgin_index] = ahd_inb(ahd, SCSIBUS); +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) + printk(" byte 0x%x\n", + ahd->msgin_buf[ahd->msgin_index]); +#endif + + message_done = ahd_parse_msg(ahd, &devinfo); + + if (message_done) { + /* + * Clear our incoming message buffer in case there + * is another message following this one. + */ + ahd->msgin_index = 0; + + /* + * If this message illicited a response, + * assert ATN so the target takes us to the + * message out phase. + */ + if (ahd->msgout_len != 0) { +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) { + ahd_print_devinfo(ahd, &devinfo); + printk("Asserting ATN for response\n"); + } +#endif + ahd_assert_atn(ahd); + } + } else + ahd->msgin_index++; + + if (message_done == MSGLOOP_TERMINATED) { + end_session = TRUE; + } else { + /* Ack the byte */ + ahd_outb(ahd, CLRSINT1, CLRREQINIT); + ahd_outb(ahd, RETURN_1, CONT_MSG_LOOP_READ); + } + break; + } + case MSG_TYPE_TARGET_MSGIN: + { + int msgdone; + int msgout_request; + + /* + * By default, the message loop will continue. + */ + ahd_outb(ahd, RETURN_1, CONT_MSG_LOOP_TARG); + + if (ahd->msgout_len == 0) + panic("Target MSGIN with no active message"); + + /* + * If we interrupted a mesgout session, the initiator + * will not know this until our first REQ. So, we + * only honor mesgout requests after we've sent our + * first byte. + */ + if ((ahd_inb(ahd, SCSISIGI) & ATNI) != 0 + && ahd->msgout_index > 0) + msgout_request = TRUE; + else + msgout_request = FALSE; + + if (msgout_request) { + + /* + * Change gears and see if + * this messages is of interest to + * us or should be passed back to + * the sequencer. + */ + ahd->msg_type = MSG_TYPE_TARGET_MSGOUT; + ahd_outb(ahd, SCSISIGO, P_MESGOUT | BSYO); + ahd->msgin_index = 0; + /* Dummy read to REQ for first byte */ + ahd_inb(ahd, SCSIDAT); + ahd_outb(ahd, SXFRCTL0, + ahd_inb(ahd, SXFRCTL0) | SPIOEN); + break; + } + + msgdone = ahd->msgout_index == ahd->msgout_len; + if (msgdone) { + ahd_outb(ahd, SXFRCTL0, + ahd_inb(ahd, SXFRCTL0) & ~SPIOEN); + end_session = TRUE; + break; + } + + /* + * Present the next byte on the bus. + */ + ahd_outb(ahd, SXFRCTL0, ahd_inb(ahd, SXFRCTL0) | SPIOEN); + ahd_outb(ahd, SCSIDAT, ahd->msgout_buf[ahd->msgout_index++]); + break; + } + case MSG_TYPE_TARGET_MSGOUT: + { + int lastbyte; + int msgdone; + + /* + * By default, the message loop will continue. + */ + ahd_outb(ahd, RETURN_1, CONT_MSG_LOOP_TARG); + + /* + * The initiator signals that this is + * the last byte by dropping ATN. + */ + lastbyte = (ahd_inb(ahd, SCSISIGI) & ATNI) == 0; + + /* + * Read the latched byte, but turn off SPIOEN first + * so that we don't inadvertently cause a REQ for the + * next byte. + */ + ahd_outb(ahd, SXFRCTL0, ahd_inb(ahd, SXFRCTL0) & ~SPIOEN); + ahd->msgin_buf[ahd->msgin_index] = ahd_inb(ahd, SCSIDAT); + msgdone = ahd_parse_msg(ahd, &devinfo); + if (msgdone == MSGLOOP_TERMINATED) { + /* + * The message is *really* done in that it caused + * us to go to bus free. The sequencer has already + * been reset at this point, so pull the ejection + * handle. + */ + return; + } + + ahd->msgin_index++; + + /* + * XXX Read spec about initiator dropping ATN too soon + * and use msgdone to detect it. + */ + if (msgdone == MSGLOOP_MSGCOMPLETE) { + ahd->msgin_index = 0; + + /* + * If this message illicited a response, transition + * to the Message in phase and send it. + */ + if (ahd->msgout_len != 0) { + ahd_outb(ahd, SCSISIGO, P_MESGIN | BSYO); + ahd_outb(ahd, SXFRCTL0, + ahd_inb(ahd, SXFRCTL0) | SPIOEN); + ahd->msg_type = MSG_TYPE_TARGET_MSGIN; + ahd->msgin_index = 0; + break; + } + } + + if (lastbyte) + end_session = TRUE; + else { + /* Ask for the next byte. */ + ahd_outb(ahd, SXFRCTL0, + ahd_inb(ahd, SXFRCTL0) | SPIOEN); + } + + break; + } + default: + panic("Unknown REQINIT message type"); + } + + if (end_session) { + if ((ahd->msg_flags & MSG_FLAG_PACKETIZED) != 0) { + printk("%s: Returning to Idle Loop\n", + ahd_name(ahd)); + ahd_clear_msg_state(ahd); + + /* + * Perform the equivalent of a clear_target_state. + */ + ahd_outb(ahd, LASTPHASE, P_BUSFREE); + ahd_outb(ahd, SEQ_FLAGS, NOT_IDENTIFIED|NO_CDB_SENT); + ahd_outb(ahd, SEQCTL0, FASTMODE|SEQRESET); + } else { + ahd_clear_msg_state(ahd); + ahd_outb(ahd, RETURN_1, EXIT_MSG_LOOP); + } + } +} + +/* + * See if we sent a particular extended message to the target. + * If "full" is true, return true only if the target saw the full + * message. If "full" is false, return true if the target saw at + * least the first byte of the message. + */ +static int +ahd_sent_msg(struct ahd_softc *ahd, ahd_msgtype type, u_int msgval, int full) +{ + int found; + u_int index; + + found = FALSE; + index = 0; + + while (index < ahd->msgout_len) { + if (ahd->msgout_buf[index] == MSG_EXTENDED) { + u_int end_index; + + end_index = index + 1 + ahd->msgout_buf[index + 1]; + if (ahd->msgout_buf[index+2] == msgval + && type == AHDMSG_EXT) { + + if (full) { + if (ahd->msgout_index > end_index) + found = TRUE; + } else if (ahd->msgout_index > index) + found = TRUE; + } + index = end_index; + } else if (ahd->msgout_buf[index] >= MSG_SIMPLE_TASK + && ahd->msgout_buf[index] <= MSG_IGN_WIDE_RESIDUE) { + + /* Skip tag type and tag id or residue param*/ + index += 2; + } else { + /* Single byte message */ + if (type == AHDMSG_1B + && ahd->msgout_index > index + && (ahd->msgout_buf[index] == msgval + || ((ahd->msgout_buf[index] & MSG_IDENTIFYFLAG) != 0 + && msgval == MSG_IDENTIFYFLAG))) + found = TRUE; + index++; + } + + if (found) + break; + } + return (found); +} + +/* + * Wait for a complete incoming message, parse it, and respond accordingly. + */ +static int +ahd_parse_msg(struct ahd_softc *ahd, struct ahd_devinfo *devinfo) +{ + struct ahd_initiator_tinfo *tinfo; + struct ahd_tmode_tstate *tstate; + int reject; + int done; + int response; + + done = MSGLOOP_IN_PROG; + response = FALSE; + reject = FALSE; + tinfo = ahd_fetch_transinfo(ahd, devinfo->channel, devinfo->our_scsiid, + devinfo->target, &tstate); + + /* + * Parse as much of the message as is available, + * rejecting it if we don't support it. When + * the entire message is available and has been + * handled, return MSGLOOP_MSGCOMPLETE, indicating + * that we have parsed an entire message. + * + * In the case of extended messages, we accept the length + * byte outright and perform more checking once we know the + * extended message type. + */ + switch (ahd->msgin_buf[0]) { + case MSG_DISCONNECT: + case MSG_SAVEDATAPOINTER: + case MSG_CMDCOMPLETE: + case MSG_RESTOREPOINTERS: + case MSG_IGN_WIDE_RESIDUE: + /* + * End our message loop as these are messages + * the sequencer handles on its own. + */ + done = MSGLOOP_TERMINATED; + break; + case MSG_MESSAGE_REJECT: + response = ahd_handle_msg_reject(ahd, devinfo); + fallthrough; + case MSG_NOOP: + done = MSGLOOP_MSGCOMPLETE; + break; + case MSG_EXTENDED: + { + /* Wait for enough of the message to begin validation */ + if (ahd->msgin_index < 2) + break; + switch (ahd->msgin_buf[2]) { + case MSG_EXT_SDTR: + { + u_int period; + u_int ppr_options; + u_int offset; + u_int saved_offset; + + if (ahd->msgin_buf[1] != MSG_EXT_SDTR_LEN) { + reject = TRUE; + break; + } + + /* + * Wait until we have both args before validating + * and acting on this message. + * + * Add one to MSG_EXT_SDTR_LEN to account for + * the extended message preamble. + */ + if (ahd->msgin_index < (MSG_EXT_SDTR_LEN + 1)) + break; + + period = ahd->msgin_buf[3]; + ppr_options = 0; + saved_offset = offset = ahd->msgin_buf[4]; + ahd_devlimited_syncrate(ahd, tinfo, &period, + &ppr_options, devinfo->role); + ahd_validate_offset(ahd, tinfo, period, &offset, + tinfo->curr.width, devinfo->role); + if (bootverbose) { + printk("(%s:%c:%d:%d): Received " + "SDTR period %x, offset %x\n\t" + "Filtered to period %x, offset %x\n", + ahd_name(ahd), devinfo->channel, + devinfo->target, devinfo->lun, + ahd->msgin_buf[3], saved_offset, + period, offset); + } + ahd_set_syncrate(ahd, devinfo, period, + offset, ppr_options, + AHD_TRANS_ACTIVE|AHD_TRANS_GOAL, + /*paused*/TRUE); + + /* + * See if we initiated Sync Negotiation + * and didn't have to fall down to async + * transfers. + */ + if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_SDTR, TRUE)) { + /* We started it */ + if (saved_offset != offset) { + /* Went too low - force async */ + reject = TRUE; + } + } else { + /* + * Send our own SDTR in reply + */ + if (bootverbose + && devinfo->role == ROLE_INITIATOR) { + printk("(%s:%c:%d:%d): Target " + "Initiated SDTR\n", + ahd_name(ahd), devinfo->channel, + devinfo->target, devinfo->lun); + } + ahd->msgout_index = 0; + ahd->msgout_len = 0; + ahd_construct_sdtr(ahd, devinfo, + period, offset); + ahd->msgout_index = 0; + response = TRUE; + } + done = MSGLOOP_MSGCOMPLETE; + break; + } + case MSG_EXT_WDTR: + { + u_int bus_width; + u_int saved_width; + u_int sending_reply; + + sending_reply = FALSE; + if (ahd->msgin_buf[1] != MSG_EXT_WDTR_LEN) { + reject = TRUE; + break; + } + + /* + * Wait until we have our arg before validating + * and acting on this message. + * + * Add one to MSG_EXT_WDTR_LEN to account for + * the extended message preamble. + */ + if (ahd->msgin_index < (MSG_EXT_WDTR_LEN + 1)) + break; + + bus_width = ahd->msgin_buf[3]; + saved_width = bus_width; + ahd_validate_width(ahd, tinfo, &bus_width, + devinfo->role); + if (bootverbose) { + printk("(%s:%c:%d:%d): Received WDTR " + "%x filtered to %x\n", + ahd_name(ahd), devinfo->channel, + devinfo->target, devinfo->lun, + saved_width, bus_width); + } + + if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_WDTR, TRUE)) { + /* + * Don't send a WDTR back to the + * target, since we asked first. + * If the width went higher than our + * request, reject it. + */ + if (saved_width > bus_width) { + reject = TRUE; + printk("(%s:%c:%d:%d): requested %dBit " + "transfers. Rejecting...\n", + ahd_name(ahd), devinfo->channel, + devinfo->target, devinfo->lun, + 8 * (0x01 << bus_width)); + bus_width = 0; + } + } else { + /* + * Send our own WDTR in reply + */ + if (bootverbose + && devinfo->role == ROLE_INITIATOR) { + printk("(%s:%c:%d:%d): Target " + "Initiated WDTR\n", + ahd_name(ahd), devinfo->channel, + devinfo->target, devinfo->lun); + } + ahd->msgout_index = 0; + ahd->msgout_len = 0; + ahd_construct_wdtr(ahd, devinfo, bus_width); + ahd->msgout_index = 0; + response = TRUE; + sending_reply = TRUE; + } + /* + * After a wide message, we are async, but + * some devices don't seem to honor this portion + * of the spec. Force a renegotiation of the + * sync component of our transfer agreement even + * if our goal is async. By updating our width + * after forcing the negotiation, we avoid + * renegotiating for width. + */ + ahd_update_neg_request(ahd, devinfo, tstate, + tinfo, AHD_NEG_ALWAYS); + ahd_set_width(ahd, devinfo, bus_width, + AHD_TRANS_ACTIVE|AHD_TRANS_GOAL, + /*paused*/TRUE); + if (sending_reply == FALSE && reject == FALSE) { + + /* + * We will always have an SDTR to send. + */ + ahd->msgout_index = 0; + ahd->msgout_len = 0; + ahd_build_transfer_msg(ahd, devinfo); + ahd->msgout_index = 0; + response = TRUE; + } + done = MSGLOOP_MSGCOMPLETE; + break; + } + case MSG_EXT_PPR: + { + u_int period; + u_int offset; + u_int bus_width; + u_int ppr_options; + u_int saved_width; + u_int saved_offset; + u_int saved_ppr_options; + + if (ahd->msgin_buf[1] != MSG_EXT_PPR_LEN) { + reject = TRUE; + break; + } + + /* + * Wait until we have all args before validating + * and acting on this message. + * + * Add one to MSG_EXT_PPR_LEN to account for + * the extended message preamble. + */ + if (ahd->msgin_index < (MSG_EXT_PPR_LEN + 1)) + break; + + period = ahd->msgin_buf[3]; + offset = ahd->msgin_buf[5]; + bus_width = ahd->msgin_buf[6]; + saved_width = bus_width; + ppr_options = ahd->msgin_buf[7]; + /* + * According to the spec, a DT only + * period factor with no DT option + * set implies async. + */ + if ((ppr_options & MSG_EXT_PPR_DT_REQ) == 0 + && period <= 9) + offset = 0; + saved_ppr_options = ppr_options; + saved_offset = offset; + + /* + * Transfer options are only available if we + * are negotiating wide. + */ + if (bus_width == 0) + ppr_options &= MSG_EXT_PPR_QAS_REQ; + + ahd_validate_width(ahd, tinfo, &bus_width, + devinfo->role); + ahd_devlimited_syncrate(ahd, tinfo, &period, + &ppr_options, devinfo->role); + ahd_validate_offset(ahd, tinfo, period, &offset, + bus_width, devinfo->role); + + if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_PPR, TRUE)) { + /* + * If we are unable to do any of the + * requested options (we went too low), + * then we'll have to reject the message. + */ + if (saved_width > bus_width + || saved_offset != offset + || saved_ppr_options != ppr_options) { + reject = TRUE; + period = 0; + offset = 0; + bus_width = 0; + ppr_options = 0; + } + } else { + if (devinfo->role != ROLE_TARGET) + printk("(%s:%c:%d:%d): Target " + "Initiated PPR\n", + ahd_name(ahd), devinfo->channel, + devinfo->target, devinfo->lun); + else + printk("(%s:%c:%d:%d): Initiator " + "Initiated PPR\n", + ahd_name(ahd), devinfo->channel, + devinfo->target, devinfo->lun); + ahd->msgout_index = 0; + ahd->msgout_len = 0; + ahd_construct_ppr(ahd, devinfo, period, offset, + bus_width, ppr_options); + ahd->msgout_index = 0; + response = TRUE; + } + if (bootverbose) { + printk("(%s:%c:%d:%d): Received PPR width %x, " + "period %x, offset %x,options %x\n" + "\tFiltered to width %x, period %x, " + "offset %x, options %x\n", + ahd_name(ahd), devinfo->channel, + devinfo->target, devinfo->lun, + saved_width, ahd->msgin_buf[3], + saved_offset, saved_ppr_options, + bus_width, period, offset, ppr_options); + } + ahd_set_width(ahd, devinfo, bus_width, + AHD_TRANS_ACTIVE|AHD_TRANS_GOAL, + /*paused*/TRUE); + ahd_set_syncrate(ahd, devinfo, period, + offset, ppr_options, + AHD_TRANS_ACTIVE|AHD_TRANS_GOAL, + /*paused*/TRUE); + + done = MSGLOOP_MSGCOMPLETE; + break; + } + default: + /* Unknown extended message. Reject it. */ + reject = TRUE; + break; + } + break; + } +#ifdef AHD_TARGET_MODE + case MSG_BUS_DEV_RESET: + ahd_handle_devreset(ahd, devinfo, CAM_LUN_WILDCARD, + CAM_BDR_SENT, + "Bus Device Reset Received", + /*verbose_level*/0); + ahd_restart(ahd); + done = MSGLOOP_TERMINATED; + break; + case MSG_ABORT_TAG: + case MSG_ABORT: + case MSG_CLEAR_QUEUE: + { + int tag; + + /* Target mode messages */ + if (devinfo->role != ROLE_TARGET) { + reject = TRUE; + break; + } + tag = SCB_LIST_NULL; + if (ahd->msgin_buf[0] == MSG_ABORT_TAG) + tag = ahd_inb(ahd, INITIATOR_TAG); + ahd_abort_scbs(ahd, devinfo->target, devinfo->channel, + devinfo->lun, tag, ROLE_TARGET, + CAM_REQ_ABORTED); + + tstate = ahd->enabled_targets[devinfo->our_scsiid]; + if (tstate != NULL) { + struct ahd_tmode_lstate* lstate; + + lstate = tstate->enabled_luns[devinfo->lun]; + if (lstate != NULL) { + ahd_queue_lstate_event(ahd, lstate, + devinfo->our_scsiid, + ahd->msgin_buf[0], + /*arg*/tag); + ahd_send_lstate_events(ahd, lstate); + } + } + ahd_restart(ahd); + done = MSGLOOP_TERMINATED; + break; + } +#endif + case MSG_QAS_REQUEST: +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) + printk("%s: QAS request. SCSISIGI == 0x%x\n", + ahd_name(ahd), ahd_inb(ahd, SCSISIGI)); +#endif + ahd->msg_flags |= MSG_FLAG_EXPECT_QASREJ_BUSFREE; + fallthrough; + case MSG_TERM_IO_PROC: + default: + reject = TRUE; + break; + } + + if (reject) { + /* + * Setup to reject the message. + */ + ahd->msgout_index = 0; + ahd->msgout_len = 1; + ahd->msgout_buf[0] = MSG_MESSAGE_REJECT; + done = MSGLOOP_MSGCOMPLETE; + response = TRUE; + } + + if (done != MSGLOOP_IN_PROG && !response) + /* Clear the outgoing message buffer */ + ahd->msgout_len = 0; + + return (done); +} + +/* + * Process a message reject message. + */ +static int +ahd_handle_msg_reject(struct ahd_softc *ahd, struct ahd_devinfo *devinfo) +{ + /* + * What we care about here is if we had an + * outstanding SDTR or WDTR message for this + * target. If we did, this is a signal that + * the target is refusing negotiation. + */ + struct scb *scb; + struct ahd_initiator_tinfo *tinfo; + struct ahd_tmode_tstate *tstate; + u_int scb_index; + u_int last_msg; + int response = 0; + + scb_index = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scb_index); + tinfo = ahd_fetch_transinfo(ahd, devinfo->channel, + devinfo->our_scsiid, + devinfo->target, &tstate); + /* Might be necessary */ + last_msg = ahd_inb(ahd, LAST_MSG); + + if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_PPR, /*full*/FALSE)) { + if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_PPR, /*full*/TRUE) + && tinfo->goal.period <= AHD_SYNCRATE_PACED) { + /* + * Target may not like our SPI-4 PPR Options. + * Attempt to negotiate 80MHz which will turn + * off these options. + */ + if (bootverbose) { + printk("(%s:%c:%d:%d): PPR Rejected. " + "Trying simple U160 PPR\n", + ahd_name(ahd), devinfo->channel, + devinfo->target, devinfo->lun); + } + tinfo->goal.period = AHD_SYNCRATE_DT; + tinfo->goal.ppr_options &= MSG_EXT_PPR_IU_REQ + | MSG_EXT_PPR_QAS_REQ + | MSG_EXT_PPR_DT_REQ; + } else { + /* + * Target does not support the PPR message. + * Attempt to negotiate SPI-2 style. + */ + if (bootverbose) { + printk("(%s:%c:%d:%d): PPR Rejected. " + "Trying WDTR/SDTR\n", + ahd_name(ahd), devinfo->channel, + devinfo->target, devinfo->lun); + } + tinfo->goal.ppr_options = 0; + tinfo->curr.transport_version = 2; + tinfo->goal.transport_version = 2; + } + ahd->msgout_index = 0; + ahd->msgout_len = 0; + ahd_build_transfer_msg(ahd, devinfo); + ahd->msgout_index = 0; + response = 1; + } else if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_WDTR, /*full*/FALSE)) { + + /* note 8bit xfers */ + printk("(%s:%c:%d:%d): refuses WIDE negotiation. Using " + "8bit transfers\n", ahd_name(ahd), + devinfo->channel, devinfo->target, devinfo->lun); + ahd_set_width(ahd, devinfo, MSG_EXT_WDTR_BUS_8_BIT, + AHD_TRANS_ACTIVE|AHD_TRANS_GOAL, + /*paused*/TRUE); + /* + * No need to clear the sync rate. If the target + * did not accept the command, our syncrate is + * unaffected. If the target started the negotiation, + * but rejected our response, we already cleared the + * sync rate before sending our WDTR. + */ + if (tinfo->goal.offset != tinfo->curr.offset) { + + /* Start the sync negotiation */ + ahd->msgout_index = 0; + ahd->msgout_len = 0; + ahd_build_transfer_msg(ahd, devinfo); + ahd->msgout_index = 0; + response = 1; + } + } else if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_SDTR, /*full*/FALSE)) { + /* note asynch xfers and clear flag */ + ahd_set_syncrate(ahd, devinfo, /*period*/0, + /*offset*/0, /*ppr_options*/0, + AHD_TRANS_ACTIVE|AHD_TRANS_GOAL, + /*paused*/TRUE); + printk("(%s:%c:%d:%d): refuses synchronous negotiation. " + "Using asynchronous transfers\n", + ahd_name(ahd), devinfo->channel, + devinfo->target, devinfo->lun); + } else if ((scb->hscb->control & MSG_SIMPLE_TASK) != 0) { + int tag_type; + int mask; + + tag_type = (scb->hscb->control & MSG_SIMPLE_TASK); + + if (tag_type == MSG_SIMPLE_TASK) { + printk("(%s:%c:%d:%d): refuses tagged commands. " + "Performing non-tagged I/O\n", ahd_name(ahd), + devinfo->channel, devinfo->target, devinfo->lun); + ahd_set_tags(ahd, scb->io_ctx, devinfo, AHD_QUEUE_NONE); + mask = ~0x23; + } else { + printk("(%s:%c:%d:%d): refuses %s tagged commands. " + "Performing simple queue tagged I/O only\n", + ahd_name(ahd), devinfo->channel, devinfo->target, + devinfo->lun, tag_type == MSG_ORDERED_TASK + ? "ordered" : "head of queue"); + ahd_set_tags(ahd, scb->io_ctx, devinfo, AHD_QUEUE_BASIC); + mask = ~0x03; + } + + /* + * Resend the identify for this CCB as the target + * may believe that the selection is invalid otherwise. + */ + ahd_outb(ahd, SCB_CONTROL, + ahd_inb_scbram(ahd, SCB_CONTROL) & mask); + scb->hscb->control &= mask; + ahd_set_transaction_tag(scb, /*enabled*/FALSE, + /*type*/MSG_SIMPLE_TASK); + ahd_outb(ahd, MSG_OUT, MSG_IDENTIFYFLAG); + ahd_assert_atn(ahd); + ahd_busy_tcl(ahd, BUILD_TCL(scb->hscb->scsiid, devinfo->lun), + SCB_GET_TAG(scb)); + + /* + * Requeue all tagged commands for this target + * currently in our possession so they can be + * converted to untagged commands. + */ + ahd_search_qinfifo(ahd, SCB_GET_TARGET(ahd, scb), + SCB_GET_CHANNEL(ahd, scb), + SCB_GET_LUN(scb), /*tag*/SCB_LIST_NULL, + ROLE_INITIATOR, CAM_REQUEUE_REQ, + SEARCH_COMPLETE); + } else if (ahd_sent_msg(ahd, AHDMSG_1B, MSG_IDENTIFYFLAG, TRUE)) { + /* + * Most likely the device believes that we had + * previously negotiated packetized. + */ + ahd->msg_flags |= MSG_FLAG_EXPECT_PPR_BUSFREE + | MSG_FLAG_IU_REQ_CHANGED; + + ahd_force_renegotiation(ahd, devinfo); + ahd->msgout_index = 0; + ahd->msgout_len = 0; + ahd_build_transfer_msg(ahd, devinfo); + ahd->msgout_index = 0; + response = 1; + } else { + /* + * Otherwise, we ignore it. + */ + printk("%s:%c:%d: Message reject for %x -- ignored\n", + ahd_name(ahd), devinfo->channel, devinfo->target, + last_msg); + } + return (response); +} + +/* + * Process an ingnore wide residue message. + */ +static void +ahd_handle_ign_wide_residue(struct ahd_softc *ahd, struct ahd_devinfo *devinfo) +{ + u_int scb_index; + struct scb *scb; + + scb_index = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scb_index); + /* + * XXX Actually check data direction in the sequencer? + * Perhaps add datadir to some spare bits in the hscb? + */ + if ((ahd_inb(ahd, SEQ_FLAGS) & DPHASE) == 0 + || ahd_get_transfer_dir(scb) != CAM_DIR_IN) { + /* + * Ignore the message if we haven't + * seen an appropriate data phase yet. + */ + } else { + /* + * If the residual occurred on the last + * transfer and the transfer request was + * expected to end on an odd count, do + * nothing. Otherwise, subtract a byte + * and update the residual count accordingly. + */ + uint32_t sgptr; + + sgptr = ahd_inb_scbram(ahd, SCB_RESIDUAL_SGPTR); + if ((sgptr & SG_LIST_NULL) != 0 + && (ahd_inb_scbram(ahd, SCB_TASK_ATTRIBUTE) + & SCB_XFERLEN_ODD) != 0) { + /* + * If the residual occurred on the last + * transfer and the transfer request was + * expected to end on an odd count, do + * nothing. + */ + } else { + uint32_t data_cnt; + uint64_t data_addr; + uint32_t sglen; + + /* Pull in the rest of the sgptr */ + sgptr = ahd_inl_scbram(ahd, SCB_RESIDUAL_SGPTR); + data_cnt = ahd_inl_scbram(ahd, SCB_RESIDUAL_DATACNT); + if ((sgptr & SG_LIST_NULL) != 0) { + /* + * The residual data count is not updated + * for the command run to completion case. + * Explicitly zero the count. + */ + data_cnt &= ~AHD_SG_LEN_MASK; + } + data_addr = ahd_inq(ahd, SHADDR); + data_cnt += 1; + data_addr -= 1; + sgptr &= SG_PTR_MASK; + if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) { + struct ahd_dma64_seg *sg; + + sg = ahd_sg_bus_to_virt(ahd, scb, sgptr); + + /* + * The residual sg ptr points to the next S/G + * to load so we must go back one. + */ + sg--; + sglen = ahd_le32toh(sg->len) & AHD_SG_LEN_MASK; + if (sg != scb->sg_list + && sglen < (data_cnt & AHD_SG_LEN_MASK)) { + + sg--; + sglen = ahd_le32toh(sg->len); + /* + * Preserve High Address and SG_LIST + * bits while setting the count to 1. + */ + data_cnt = 1|(sglen&(~AHD_SG_LEN_MASK)); + data_addr = ahd_le64toh(sg->addr) + + (sglen & AHD_SG_LEN_MASK) + - 1; + + /* + * Increment sg so it points to the + * "next" sg. + */ + sg++; + sgptr = ahd_sg_virt_to_bus(ahd, scb, + sg); + } + } else { + struct ahd_dma_seg *sg; + + sg = ahd_sg_bus_to_virt(ahd, scb, sgptr); + + /* + * The residual sg ptr points to the next S/G + * to load so we must go back one. + */ + sg--; + sglen = ahd_le32toh(sg->len) & AHD_SG_LEN_MASK; + if (sg != scb->sg_list + && sglen < (data_cnt & AHD_SG_LEN_MASK)) { + + sg--; + sglen = ahd_le32toh(sg->len); + /* + * Preserve High Address and SG_LIST + * bits while setting the count to 1. + */ + data_cnt = 1|(sglen&(~AHD_SG_LEN_MASK)); + data_addr = ahd_le32toh(sg->addr) + + (sglen & AHD_SG_LEN_MASK) + - 1; + + /* + * Increment sg so it points to the + * "next" sg. + */ + sg++; + sgptr = ahd_sg_virt_to_bus(ahd, scb, + sg); + } + } + /* + * Toggle the "oddness" of the transfer length + * to handle this mid-transfer ignore wide + * residue. This ensures that the oddness is + * correct for subsequent data transfers. + */ + ahd_outb(ahd, SCB_TASK_ATTRIBUTE, + ahd_inb_scbram(ahd, SCB_TASK_ATTRIBUTE) + ^ SCB_XFERLEN_ODD); + + ahd_outl(ahd, SCB_RESIDUAL_SGPTR, sgptr); + ahd_outl(ahd, SCB_RESIDUAL_DATACNT, data_cnt); + /* + * The FIFO's pointers will be updated if/when the + * sequencer re-enters a data phase. + */ + } + } +} + + +/* + * Reinitialize the data pointers for the active transfer + * based on its current residual. + */ +static void +ahd_reinitialize_dataptrs(struct ahd_softc *ahd) +{ + struct scb *scb; + ahd_mode_state saved_modes; + u_int scb_index; + u_int wait; + uint32_t sgptr; + uint32_t resid; + uint64_t dataptr; + + AHD_ASSERT_MODES(ahd, AHD_MODE_DFF0_MSK|AHD_MODE_DFF1_MSK, + AHD_MODE_DFF0_MSK|AHD_MODE_DFF1_MSK); + + scb_index = ahd_get_scbptr(ahd); + scb = ahd_lookup_scb(ahd, scb_index); + + /* + * Release and reacquire the FIFO so we + * have a clean slate. + */ + ahd_outb(ahd, DFFSXFRCTL, CLRCHN); + wait = 1000; + while (--wait && !(ahd_inb(ahd, MDFFSTAT) & FIFOFREE)) + ahd_delay(100); + if (wait == 0) { + ahd_print_path(ahd, scb); + printk("ahd_reinitialize_dataptrs: Forcing FIFO free.\n"); + ahd_outb(ahd, DFFSXFRCTL, RSTCHN|CLRSHCNT); + } + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + ahd_outb(ahd, DFFSTAT, + ahd_inb(ahd, DFFSTAT) + | (saved_modes == 0x11 ? CURRFIFO_1 : CURRFIFO_0)); + + /* + * Determine initial values for data_addr and data_cnt + * for resuming the data phase. + */ + sgptr = ahd_inl_scbram(ahd, SCB_RESIDUAL_SGPTR); + sgptr &= SG_PTR_MASK; + + resid = (ahd_inb_scbram(ahd, SCB_RESIDUAL_DATACNT + 2) << 16) + | (ahd_inb_scbram(ahd, SCB_RESIDUAL_DATACNT + 1) << 8) + | ahd_inb_scbram(ahd, SCB_RESIDUAL_DATACNT); + + if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) { + struct ahd_dma64_seg *sg; + + sg = ahd_sg_bus_to_virt(ahd, scb, sgptr); + + /* The residual sg_ptr always points to the next sg */ + sg--; + + dataptr = ahd_le64toh(sg->addr) + + (ahd_le32toh(sg->len) & AHD_SG_LEN_MASK) + - resid; + ahd_outl(ahd, HADDR + 4, dataptr >> 32); + } else { + struct ahd_dma_seg *sg; + + sg = ahd_sg_bus_to_virt(ahd, scb, sgptr); + + /* The residual sg_ptr always points to the next sg */ + sg--; + + dataptr = ahd_le32toh(sg->addr) + + (ahd_le32toh(sg->len) & AHD_SG_LEN_MASK) + - resid; + ahd_outb(ahd, HADDR + 4, + (ahd_le32toh(sg->len) & ~AHD_SG_LEN_MASK) >> 24); + } + ahd_outl(ahd, HADDR, dataptr); + ahd_outb(ahd, HCNT + 2, resid >> 16); + ahd_outb(ahd, HCNT + 1, resid >> 8); + ahd_outb(ahd, HCNT, resid); +} + +/* + * Handle the effects of issuing a bus device reset message. + */ +static void +ahd_handle_devreset(struct ahd_softc *ahd, struct ahd_devinfo *devinfo, + u_int lun, cam_status status, char *message, + int verbose_level) +{ +#ifdef AHD_TARGET_MODE + struct ahd_tmode_tstate* tstate; +#endif + int found; + + found = ahd_abort_scbs(ahd, devinfo->target, devinfo->channel, + lun, SCB_LIST_NULL, devinfo->role, + status); + +#ifdef AHD_TARGET_MODE + /* + * Send an immediate notify ccb to all target mord peripheral + * drivers affected by this action. + */ + tstate = ahd->enabled_targets[devinfo->our_scsiid]; + if (tstate != NULL) { + u_int cur_lun; + u_int max_lun; + + if (lun != CAM_LUN_WILDCARD) { + cur_lun = 0; + max_lun = AHD_NUM_LUNS - 1; + } else { + cur_lun = lun; + max_lun = lun; + } + for (;cur_lun <= max_lun; cur_lun++) { + struct ahd_tmode_lstate* lstate; + + lstate = tstate->enabled_luns[cur_lun]; + if (lstate == NULL) + continue; + + ahd_queue_lstate_event(ahd, lstate, devinfo->our_scsiid, + MSG_BUS_DEV_RESET, /*arg*/0); + ahd_send_lstate_events(ahd, lstate); + } + } +#endif + + /* + * Go back to async/narrow transfers and renegotiate. + */ + ahd_set_width(ahd, devinfo, MSG_EXT_WDTR_BUS_8_BIT, + AHD_TRANS_CUR, /*paused*/TRUE); + ahd_set_syncrate(ahd, devinfo, /*period*/0, /*offset*/0, + /*ppr_options*/0, AHD_TRANS_CUR, + /*paused*/TRUE); + + if (status != CAM_SEL_TIMEOUT) + ahd_send_async(ahd, devinfo->channel, devinfo->target, + CAM_LUN_WILDCARD, AC_SENT_BDR); + + if (message != NULL && bootverbose) + printk("%s: %s on %c:%d. %d SCBs aborted\n", ahd_name(ahd), + message, devinfo->channel, devinfo->target, found); +} + +#ifdef AHD_TARGET_MODE +static void +ahd_setup_target_msgin(struct ahd_softc *ahd, struct ahd_devinfo *devinfo, + struct scb *scb) +{ + + /* + * To facilitate adding multiple messages together, + * each routine should increment the index and len + * variables instead of setting them explicitly. + */ + ahd->msgout_index = 0; + ahd->msgout_len = 0; + + if (scb != NULL && (scb->flags & SCB_AUTO_NEGOTIATE) != 0) + ahd_build_transfer_msg(ahd, devinfo); + else + panic("ahd_intr: AWAITING target message with no message"); + + ahd->msgout_index = 0; + ahd->msg_type = MSG_TYPE_TARGET_MSGIN; +} +#endif +/**************************** Initialization **********************************/ +static u_int +ahd_sglist_size(struct ahd_softc *ahd) +{ + bus_size_t list_size; + + list_size = sizeof(struct ahd_dma_seg) * AHD_NSEG; + if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) + list_size = sizeof(struct ahd_dma64_seg) * AHD_NSEG; + return (list_size); +} + +/* + * Calculate the optimum S/G List allocation size. S/G elements used + * for a given transaction must be physically contiguous. Assume the + * OS will allocate full pages to us, so it doesn't make sense to request + * less than a page. + */ +static u_int +ahd_sglist_allocsize(struct ahd_softc *ahd) +{ + bus_size_t sg_list_increment; + bus_size_t sg_list_size; + bus_size_t max_list_size; + bus_size_t best_list_size; + + /* Start out with the minimum required for AHD_NSEG. */ + sg_list_increment = ahd_sglist_size(ahd); + sg_list_size = sg_list_increment; + + /* Get us as close as possible to a page in size. */ + while ((sg_list_size + sg_list_increment) <= PAGE_SIZE) + sg_list_size += sg_list_increment; + + /* + * Try to reduce the amount of wastage by allocating + * multiple pages. + */ + best_list_size = sg_list_size; + max_list_size = roundup(sg_list_increment, PAGE_SIZE); + if (max_list_size < 4 * PAGE_SIZE) + max_list_size = 4 * PAGE_SIZE; + if (max_list_size > (AHD_SCB_MAX_ALLOC * sg_list_increment)) + max_list_size = (AHD_SCB_MAX_ALLOC * sg_list_increment); + while ((sg_list_size + sg_list_increment) <= max_list_size + && (sg_list_size % PAGE_SIZE) != 0) { + bus_size_t new_mod; + bus_size_t best_mod; + + sg_list_size += sg_list_increment; + new_mod = sg_list_size % PAGE_SIZE; + best_mod = best_list_size % PAGE_SIZE; + if (new_mod > best_mod || new_mod == 0) { + best_list_size = sg_list_size; + } + } + return (best_list_size); +} + +/* + * Allocate a controller structure for a new device + * and perform initial initializion. + */ +struct ahd_softc * +ahd_alloc(void *platform_arg, char *name) +{ + struct ahd_softc *ahd; + + ahd = kzalloc(sizeof(*ahd), GFP_ATOMIC); + if (!ahd) { + printk("aic7xxx: cannot malloc softc!\n"); + kfree(name); + return NULL; + } + + ahd->seep_config = kmalloc(sizeof(*ahd->seep_config), GFP_ATOMIC); + if (ahd->seep_config == NULL) { + kfree(ahd); + kfree(name); + return (NULL); + } + LIST_INIT(&ahd->pending_scbs); + /* We don't know our unit number until the OSM sets it */ + ahd->name = name; + ahd->unit = -1; + ahd->description = NULL; + ahd->bus_description = NULL; + ahd->channel = 'A'; + ahd->chip = AHD_NONE; + ahd->features = AHD_FENONE; + ahd->bugs = AHD_BUGNONE; + ahd->flags = AHD_SPCHK_ENB_A|AHD_RESET_BUS_A|AHD_TERM_ENB_A + | AHD_EXTENDED_TRANS_A|AHD_STPWLEVEL_A; + timer_setup(&ahd->stat_timer, ahd_stat_timer, 0); + ahd->int_coalescing_timer = AHD_INT_COALESCING_TIMER_DEFAULT; + ahd->int_coalescing_maxcmds = AHD_INT_COALESCING_MAXCMDS_DEFAULT; + ahd->int_coalescing_mincmds = AHD_INT_COALESCING_MINCMDS_DEFAULT; + ahd->int_coalescing_threshold = AHD_INT_COALESCING_THRESHOLD_DEFAULT; + ahd->int_coalescing_stop_threshold = + AHD_INT_COALESCING_STOP_THRESHOLD_DEFAULT; + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MEMORY) != 0) { + printk("%s: scb size = 0x%x, hscb size = 0x%x\n", + ahd_name(ahd), (u_int)sizeof(struct scb), + (u_int)sizeof(struct hardware_scb)); + } +#endif + if (ahd_platform_alloc(ahd, platform_arg) != 0) { + ahd_free(ahd); + ahd = NULL; + } + return (ahd); +} + +int +ahd_softc_init(struct ahd_softc *ahd) +{ + + ahd->unpause = 0; + ahd->pause = PAUSE; + return (0); +} + +void +ahd_set_unit(struct ahd_softc *ahd, int unit) +{ + ahd->unit = unit; +} + +void +ahd_set_name(struct ahd_softc *ahd, char *name) +{ + kfree(ahd->name); + ahd->name = name; +} + +void +ahd_free(struct ahd_softc *ahd) +{ + int i; + + switch (ahd->init_level) { + default: + case 5: + ahd_shutdown(ahd); + fallthrough; + case 4: + ahd_dmamap_unload(ahd, ahd->shared_data_dmat, + ahd->shared_data_map.dmamap); + fallthrough; + case 3: + ahd_dmamem_free(ahd, ahd->shared_data_dmat, ahd->qoutfifo, + ahd->shared_data_map.dmamap); + ahd_dmamap_destroy(ahd, ahd->shared_data_dmat, + ahd->shared_data_map.dmamap); + fallthrough; + case 2: + ahd_dma_tag_destroy(ahd, ahd->shared_data_dmat); + case 1: + break; + case 0: + break; + } + + ahd_platform_free(ahd); + ahd_fini_scbdata(ahd); + for (i = 0; i < AHD_NUM_TARGETS; i++) { + struct ahd_tmode_tstate *tstate; + + tstate = ahd->enabled_targets[i]; + if (tstate != NULL) { +#ifdef AHD_TARGET_MODE + int j; + + for (j = 0; j < AHD_NUM_LUNS; j++) { + struct ahd_tmode_lstate *lstate; + + lstate = tstate->enabled_luns[j]; + if (lstate != NULL) { + xpt_free_path(lstate->path); + kfree(lstate); + } + } +#endif + kfree(tstate); + } + } +#ifdef AHD_TARGET_MODE + if (ahd->black_hole != NULL) { + xpt_free_path(ahd->black_hole->path); + kfree(ahd->black_hole); + } +#endif + kfree(ahd->name); + kfree(ahd->seep_config); + kfree(ahd->saved_stack); + kfree(ahd); + return; +} + +static void +ahd_shutdown(void *arg) +{ + struct ahd_softc *ahd; + + ahd = (struct ahd_softc *)arg; + + /* + * Stop periodic timer callbacks. + */ + del_timer_sync(&ahd->stat_timer); + + /* This will reset most registers to 0, but not all */ + ahd_reset(ahd, /*reinit*/FALSE); +} + +/* + * Reset the controller and record some information about it + * that is only available just after a reset. If "reinit" is + * non-zero, this reset occurred after initial configuration + * and the caller requests that the chip be fully reinitialized + * to a runable state. Chip interrupts are *not* enabled after + * a reinitialization. The caller must enable interrupts via + * ahd_intr_enable(). + */ +int +ahd_reset(struct ahd_softc *ahd, int reinit) +{ + u_int sxfrctl1; + int wait; + uint32_t cmd; + + /* + * Preserve the value of the SXFRCTL1 register for all channels. + * It contains settings that affect termination and we don't want + * to disturb the integrity of the bus. + */ + ahd_pause(ahd); + ahd_update_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + sxfrctl1 = ahd_inb(ahd, SXFRCTL1); + + cmd = ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2); + if ((ahd->bugs & AHD_PCIX_CHIPRST_BUG) != 0) { + uint32_t mod_cmd; + + /* + * A4 Razor #632 + * During the assertion of CHIPRST, the chip + * does not disable its parity logic prior to + * the start of the reset. This may cause a + * parity error to be detected and thus a + * spurious SERR or PERR assertion. Disable + * PERR and SERR responses during the CHIPRST. + */ + mod_cmd = cmd & ~(PCIM_CMD_PERRESPEN|PCIM_CMD_SERRESPEN); + ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, + mod_cmd, /*bytes*/2); + } + ahd_outb(ahd, HCNTRL, CHIPRST | ahd->pause); + + /* + * Ensure that the reset has finished. We delay 1000us + * prior to reading the register to make sure the chip + * has sufficiently completed its reset to handle register + * accesses. + */ + wait = 1000; + do { + ahd_delay(1000); + } while (--wait && !(ahd_inb(ahd, HCNTRL) & CHIPRSTACK)); + + if (wait == 0) { + printk("%s: WARNING - Failed chip reset! " + "Trying to initialize anyway.\n", ahd_name(ahd)); + } + ahd_outb(ahd, HCNTRL, ahd->pause); + + if ((ahd->bugs & AHD_PCIX_CHIPRST_BUG) != 0) { + /* + * Clear any latched PCI error status and restore + * previous SERR and PERR response enables. + */ + ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, + 0xFF, /*bytes*/1); + ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, + cmd, /*bytes*/2); + } + + /* + * Mode should be SCSI after a chip reset, but lets + * set it just to be safe. We touch the MODE_PTR + * register directly so as to bypass the lazy update + * code in ahd_set_modes(). + */ + ahd_known_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + ahd_outb(ahd, MODE_PTR, + ahd_build_mode_state(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI)); + + /* + * Restore SXFRCTL1. + * + * We must always initialize STPWEN to 1 before we + * restore the saved values. STPWEN is initialized + * to a tri-state condition which can only be cleared + * by turning it on. + */ + ahd_outb(ahd, SXFRCTL1, sxfrctl1|STPWEN); + ahd_outb(ahd, SXFRCTL1, sxfrctl1); + + /* Determine chip configuration */ + ahd->features &= ~AHD_WIDE; + if ((ahd_inb(ahd, SBLKCTL) & SELWIDE) != 0) + ahd->features |= AHD_WIDE; + + /* + * If a recovery action has forced a chip reset, + * re-initialize the chip to our liking. + */ + if (reinit != 0) + ahd_chip_init(ahd); + + return (0); +} + +/* + * Determine the number of SCBs available on the controller + */ +static int +ahd_probe_scbs(struct ahd_softc *ahd) { + int i; + + AHD_ASSERT_MODES(ahd, ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK), + ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK)); + for (i = 0; i < AHD_SCB_MAX; i++) { + int j; + + ahd_set_scbptr(ahd, i); + ahd_outw(ahd, SCB_BASE, i); + for (j = 2; j < 64; j++) + ahd_outb(ahd, SCB_BASE+j, 0); + /* Start out life as unallocated (needing an abort) */ + ahd_outb(ahd, SCB_CONTROL, MK_MESSAGE); + if (ahd_inw_scbram(ahd, SCB_BASE) != i) + break; + ahd_set_scbptr(ahd, 0); + if (ahd_inw_scbram(ahd, SCB_BASE) != 0) + break; + } + return (i); +} + +static void +ahd_dmamap_cb(void *arg, bus_dma_segment_t *segs, int nseg, int error) +{ + dma_addr_t *baddr; + + baddr = (dma_addr_t *)arg; + *baddr = segs->ds_addr; +} + +static void +ahd_initialize_hscbs(struct ahd_softc *ahd) +{ + int i; + + for (i = 0; i < ahd->scb_data.maxhscbs; i++) { + ahd_set_scbptr(ahd, i); + + /* Clear the control byte. */ + ahd_outb(ahd, SCB_CONTROL, 0); + + /* Set the next pointer */ + ahd_outw(ahd, SCB_NEXT, SCB_LIST_NULL); + } +} + +static int +ahd_init_scbdata(struct ahd_softc *ahd) +{ + struct scb_data *scb_data; + int i; + + scb_data = &ahd->scb_data; + TAILQ_INIT(&scb_data->free_scbs); + for (i = 0; i < AHD_NUM_TARGETS * AHD_NUM_LUNS_NONPKT; i++) + LIST_INIT(&scb_data->free_scb_lists[i]); + LIST_INIT(&scb_data->any_dev_free_scb_list); + SLIST_INIT(&scb_data->hscb_maps); + SLIST_INIT(&scb_data->sg_maps); + SLIST_INIT(&scb_data->sense_maps); + + /* Determine the number of hardware SCBs and initialize them */ + scb_data->maxhscbs = ahd_probe_scbs(ahd); + if (scb_data->maxhscbs == 0) { + printk("%s: No SCB space found\n", ahd_name(ahd)); + return (ENXIO); + } + + ahd_initialize_hscbs(ahd); + + /* + * Create our DMA tags. These tags define the kinds of device + * accessible memory allocations and memory mappings we will + * need to perform during normal operation. + * + * Unless we need to further restrict the allocation, we rely + * on the restrictions of the parent dmat, hence the common + * use of MAXADDR and MAXSIZE. + */ + + /* DMA tag for our hardware scb structures */ + if (ahd_dma_tag_create(ahd, ahd->parent_dmat, /*alignment*/1, + /*boundary*/BUS_SPACE_MAXADDR_32BIT + 1, + /*lowaddr*/BUS_SPACE_MAXADDR_32BIT, + /*highaddr*/BUS_SPACE_MAXADDR, + /*filter*/NULL, /*filterarg*/NULL, + PAGE_SIZE, /*nsegments*/1, + /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, + /*flags*/0, &scb_data->hscb_dmat) != 0) { + goto error_exit; + } + + scb_data->init_level++; + + /* DMA tag for our S/G structures. */ + if (ahd_dma_tag_create(ahd, ahd->parent_dmat, /*alignment*/8, + /*boundary*/BUS_SPACE_MAXADDR_32BIT + 1, + /*lowaddr*/BUS_SPACE_MAXADDR_32BIT, + /*highaddr*/BUS_SPACE_MAXADDR, + /*filter*/NULL, /*filterarg*/NULL, + ahd_sglist_allocsize(ahd), /*nsegments*/1, + /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, + /*flags*/0, &scb_data->sg_dmat) != 0) { + goto error_exit; + } +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MEMORY) != 0) + printk("%s: ahd_sglist_allocsize = 0x%x\n", ahd_name(ahd), + ahd_sglist_allocsize(ahd)); +#endif + + scb_data->init_level++; + + /* DMA tag for our sense buffers. We allocate in page sized chunks */ + if (ahd_dma_tag_create(ahd, ahd->parent_dmat, /*alignment*/1, + /*boundary*/BUS_SPACE_MAXADDR_32BIT + 1, + /*lowaddr*/BUS_SPACE_MAXADDR_32BIT, + /*highaddr*/BUS_SPACE_MAXADDR, + /*filter*/NULL, /*filterarg*/NULL, + PAGE_SIZE, /*nsegments*/1, + /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, + /*flags*/0, &scb_data->sense_dmat) != 0) { + goto error_exit; + } + + scb_data->init_level++; + + /* Perform initial CCB allocation */ + ahd_alloc_scbs(ahd); + + if (scb_data->numscbs == 0) { + printk("%s: ahd_init_scbdata - " + "Unable to allocate initial scbs\n", + ahd_name(ahd)); + goto error_exit; + } + + /* + * Note that we were successful + */ + return (0); + +error_exit: + + return (ENOMEM); +} + +static struct scb * +ahd_find_scb_by_tag(struct ahd_softc *ahd, u_int tag) +{ + struct scb *scb; + + /* + * Look on the pending list. + */ + LIST_FOREACH(scb, &ahd->pending_scbs, pending_links) { + if (SCB_GET_TAG(scb) == tag) + return (scb); + } + + /* + * Then on all of the collision free lists. + */ + TAILQ_FOREACH(scb, &ahd->scb_data.free_scbs, links.tqe) { + struct scb *list_scb; + + list_scb = scb; + do { + if (SCB_GET_TAG(list_scb) == tag) + return (list_scb); + list_scb = LIST_NEXT(list_scb, collision_links); + } while (list_scb); + } + + /* + * And finally on the generic free list. + */ + LIST_FOREACH(scb, &ahd->scb_data.any_dev_free_scb_list, links.le) { + if (SCB_GET_TAG(scb) == tag) + return (scb); + } + + return (NULL); +} + +static void +ahd_fini_scbdata(struct ahd_softc *ahd) +{ + struct scb_data *scb_data; + + scb_data = &ahd->scb_data; + if (scb_data == NULL) + return; + + switch (scb_data->init_level) { + default: + case 7: + { + struct map_node *sns_map; + + while ((sns_map = SLIST_FIRST(&scb_data->sense_maps)) != NULL) { + SLIST_REMOVE_HEAD(&scb_data->sense_maps, links); + ahd_dmamap_unload(ahd, scb_data->sense_dmat, + sns_map->dmamap); + ahd_dmamem_free(ahd, scb_data->sense_dmat, + sns_map->vaddr, sns_map->dmamap); + kfree(sns_map); + } + ahd_dma_tag_destroy(ahd, scb_data->sense_dmat); + } + fallthrough; + case 6: + { + struct map_node *sg_map; + + while ((sg_map = SLIST_FIRST(&scb_data->sg_maps)) != NULL) { + SLIST_REMOVE_HEAD(&scb_data->sg_maps, links); + ahd_dmamap_unload(ahd, scb_data->sg_dmat, + sg_map->dmamap); + ahd_dmamem_free(ahd, scb_data->sg_dmat, + sg_map->vaddr, sg_map->dmamap); + kfree(sg_map); + } + ahd_dma_tag_destroy(ahd, scb_data->sg_dmat); + } + fallthrough; + case 5: + { + struct map_node *hscb_map; + + while ((hscb_map = SLIST_FIRST(&scb_data->hscb_maps)) != NULL) { + SLIST_REMOVE_HEAD(&scb_data->hscb_maps, links); + ahd_dmamap_unload(ahd, scb_data->hscb_dmat, + hscb_map->dmamap); + ahd_dmamem_free(ahd, scb_data->hscb_dmat, + hscb_map->vaddr, hscb_map->dmamap); + kfree(hscb_map); + } + ahd_dma_tag_destroy(ahd, scb_data->hscb_dmat); + /* FALLTHROUGH */ + } + case 4: + case 3: + case 2: + case 1: + case 0: + break; + } +} + +/* + * DSP filter Bypass must be enabled until the first selection + * after a change in bus mode (Razor #491 and #493). + */ +static void +ahd_setup_iocell_workaround(struct ahd_softc *ahd) +{ + ahd_mode_state saved_modes; + + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); + ahd_outb(ahd, DSPDATACTL, ahd_inb(ahd, DSPDATACTL) + | BYPASSENAB | RCVROFFSTDIS | XMITOFFSTDIS); + ahd_outb(ahd, SIMODE0, ahd_inb(ahd, SIMODE0) | (ENSELDO|ENSELDI)); +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MISC) != 0) + printk("%s: Setting up iocell workaround\n", ahd_name(ahd)); +#endif + ahd_restore_modes(ahd, saved_modes); + ahd->flags &= ~AHD_HAD_FIRST_SEL; +} + +static void +ahd_iocell_first_selection(struct ahd_softc *ahd) +{ + ahd_mode_state saved_modes; + u_int sblkctl; + + if ((ahd->flags & AHD_HAD_FIRST_SEL) != 0) + return; + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + sblkctl = ahd_inb(ahd, SBLKCTL); + ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MISC) != 0) + printk("%s: iocell first selection\n", ahd_name(ahd)); +#endif + if ((sblkctl & ENAB40) != 0) { + ahd_outb(ahd, DSPDATACTL, + ahd_inb(ahd, DSPDATACTL) & ~BYPASSENAB); +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MISC) != 0) + printk("%s: BYPASS now disabled\n", ahd_name(ahd)); +#endif + } + ahd_outb(ahd, SIMODE0, ahd_inb(ahd, SIMODE0) & ~(ENSELDO|ENSELDI)); + ahd_outb(ahd, CLRINT, CLRSCSIINT); + ahd_restore_modes(ahd, saved_modes); + ahd->flags |= AHD_HAD_FIRST_SEL; +} + +/*************************** SCB Management ***********************************/ +static void +ahd_add_col_list(struct ahd_softc *ahd, struct scb *scb, u_int col_idx) +{ + struct scb_list *free_list; + struct scb_tailq *free_tailq; + struct scb *first_scb; + + scb->flags |= SCB_ON_COL_LIST; + AHD_SET_SCB_COL_IDX(scb, col_idx); + free_list = &ahd->scb_data.free_scb_lists[col_idx]; + free_tailq = &ahd->scb_data.free_scbs; + first_scb = LIST_FIRST(free_list); + if (first_scb != NULL) { + LIST_INSERT_AFTER(first_scb, scb, collision_links); + } else { + LIST_INSERT_HEAD(free_list, scb, collision_links); + TAILQ_INSERT_TAIL(free_tailq, scb, links.tqe); + } +} + +static void +ahd_rem_col_list(struct ahd_softc *ahd, struct scb *scb) +{ + struct scb_list *free_list; + struct scb_tailq *free_tailq; + struct scb *first_scb; + u_int col_idx; + + scb->flags &= ~SCB_ON_COL_LIST; + col_idx = AHD_GET_SCB_COL_IDX(ahd, scb); + free_list = &ahd->scb_data.free_scb_lists[col_idx]; + free_tailq = &ahd->scb_data.free_scbs; + first_scb = LIST_FIRST(free_list); + if (first_scb == scb) { + struct scb *next_scb; + + /* + * Maintain order in the collision free + * lists for fairness if this device has + * other colliding tags active. + */ + next_scb = LIST_NEXT(scb, collision_links); + if (next_scb != NULL) { + TAILQ_INSERT_AFTER(free_tailq, scb, + next_scb, links.tqe); + } + TAILQ_REMOVE(free_tailq, scb, links.tqe); + } + LIST_REMOVE(scb, collision_links); +} + +/* + * Get a free scb. If there are none, see if we can allocate a new SCB. + */ +struct scb * +ahd_get_scb(struct ahd_softc *ahd, u_int col_idx) +{ + struct scb *scb; + int tries; + + tries = 0; +look_again: + TAILQ_FOREACH(scb, &ahd->scb_data.free_scbs, links.tqe) { + if (AHD_GET_SCB_COL_IDX(ahd, scb) != col_idx) { + ahd_rem_col_list(ahd, scb); + goto found; + } + } + if ((scb = LIST_FIRST(&ahd->scb_data.any_dev_free_scb_list)) == NULL) { + + if (tries++ != 0) + return (NULL); + ahd_alloc_scbs(ahd); + goto look_again; + } + LIST_REMOVE(scb, links.le); + if (col_idx != AHD_NEVER_COL_IDX + && (scb->col_scb != NULL) + && (scb->col_scb->flags & SCB_ACTIVE) == 0) { + LIST_REMOVE(scb->col_scb, links.le); + ahd_add_col_list(ahd, scb->col_scb, col_idx); + } +found: + scb->flags |= SCB_ACTIVE; + return (scb); +} + +/* + * Return an SCB resource to the free list. + */ +void +ahd_free_scb(struct ahd_softc *ahd, struct scb *scb) +{ + /* Clean up for the next user */ + scb->flags = SCB_FLAG_NONE; + scb->hscb->control = 0; + ahd->scb_data.scbindex[SCB_GET_TAG(scb)] = NULL; + + if (scb->col_scb == NULL) { + + /* + * No collision possible. Just free normally. + */ + LIST_INSERT_HEAD(&ahd->scb_data.any_dev_free_scb_list, + scb, links.le); + } else if ((scb->col_scb->flags & SCB_ON_COL_LIST) != 0) { + + /* + * The SCB we might have collided with is on + * a free collision list. Put both SCBs on + * the generic list. + */ + ahd_rem_col_list(ahd, scb->col_scb); + LIST_INSERT_HEAD(&ahd->scb_data.any_dev_free_scb_list, + scb, links.le); + LIST_INSERT_HEAD(&ahd->scb_data.any_dev_free_scb_list, + scb->col_scb, links.le); + } else if ((scb->col_scb->flags + & (SCB_PACKETIZED|SCB_ACTIVE)) == SCB_ACTIVE + && (scb->col_scb->hscb->control & TAG_ENB) != 0) { + + /* + * The SCB we might collide with on the next allocation + * is still active in a non-packetized, tagged, context. + * Put us on the SCB collision list. + */ + ahd_add_col_list(ahd, scb, + AHD_GET_SCB_COL_IDX(ahd, scb->col_scb)); + } else { + /* + * The SCB we might collide with on the next allocation + * is either active in a packetized context, or free. + * Since we can't collide, put this SCB on the generic + * free list. + */ + LIST_INSERT_HEAD(&ahd->scb_data.any_dev_free_scb_list, + scb, links.le); + } + + ahd_platform_scb_free(ahd, scb); +} + +static void +ahd_alloc_scbs(struct ahd_softc *ahd) +{ + struct scb_data *scb_data; + struct scb *next_scb; + struct hardware_scb *hscb; + struct map_node *hscb_map; + struct map_node *sg_map; + struct map_node *sense_map; + uint8_t *segs; + uint8_t *sense_data; + dma_addr_t hscb_busaddr; + dma_addr_t sg_busaddr; + dma_addr_t sense_busaddr; + int newcount; + int i; + + scb_data = &ahd->scb_data; + if (scb_data->numscbs >= AHD_SCB_MAX_ALLOC) + /* Can't allocate any more */ + return; + + if (scb_data->scbs_left != 0) { + int offset; + + offset = (PAGE_SIZE / sizeof(*hscb)) - scb_data->scbs_left; + hscb_map = SLIST_FIRST(&scb_data->hscb_maps); + hscb = &((struct hardware_scb *)hscb_map->vaddr)[offset]; + hscb_busaddr = hscb_map->physaddr + (offset * sizeof(*hscb)); + } else { + hscb_map = kmalloc(sizeof(*hscb_map), GFP_ATOMIC); + + if (hscb_map == NULL) + return; + + /* Allocate the next batch of hardware SCBs */ + if (ahd_dmamem_alloc(ahd, scb_data->hscb_dmat, + (void **)&hscb_map->vaddr, + BUS_DMA_NOWAIT, &hscb_map->dmamap) != 0) { + kfree(hscb_map); + return; + } + + SLIST_INSERT_HEAD(&scb_data->hscb_maps, hscb_map, links); + + ahd_dmamap_load(ahd, scb_data->hscb_dmat, hscb_map->dmamap, + hscb_map->vaddr, PAGE_SIZE, ahd_dmamap_cb, + &hscb_map->physaddr, /*flags*/0); + + hscb = (struct hardware_scb *)hscb_map->vaddr; + hscb_busaddr = hscb_map->physaddr; + scb_data->scbs_left = PAGE_SIZE / sizeof(*hscb); + } + + if (scb_data->sgs_left != 0) { + int offset; + + offset = ((ahd_sglist_allocsize(ahd) / ahd_sglist_size(ahd)) + - scb_data->sgs_left) * ahd_sglist_size(ahd); + sg_map = SLIST_FIRST(&scb_data->sg_maps); + segs = sg_map->vaddr + offset; + sg_busaddr = sg_map->physaddr + offset; + } else { + sg_map = kmalloc(sizeof(*sg_map), GFP_ATOMIC); + + if (sg_map == NULL) + return; + + /* Allocate the next batch of S/G lists */ + if (ahd_dmamem_alloc(ahd, scb_data->sg_dmat, + (void **)&sg_map->vaddr, + BUS_DMA_NOWAIT, &sg_map->dmamap) != 0) { + kfree(sg_map); + return; + } + + SLIST_INSERT_HEAD(&scb_data->sg_maps, sg_map, links); + + ahd_dmamap_load(ahd, scb_data->sg_dmat, sg_map->dmamap, + sg_map->vaddr, ahd_sglist_allocsize(ahd), + ahd_dmamap_cb, &sg_map->physaddr, /*flags*/0); + + segs = sg_map->vaddr; + sg_busaddr = sg_map->physaddr; + scb_data->sgs_left = + ahd_sglist_allocsize(ahd) / ahd_sglist_size(ahd); +#ifdef AHD_DEBUG + if (ahd_debug & AHD_SHOW_MEMORY) + printk("Mapped SG data\n"); +#endif + } + + if (scb_data->sense_left != 0) { + int offset; + + offset = PAGE_SIZE - (AHD_SENSE_BUFSIZE * scb_data->sense_left); + sense_map = SLIST_FIRST(&scb_data->sense_maps); + sense_data = sense_map->vaddr + offset; + sense_busaddr = sense_map->physaddr + offset; + } else { + sense_map = kmalloc(sizeof(*sense_map), GFP_ATOMIC); + + if (sense_map == NULL) + return; + + /* Allocate the next batch of sense buffers */ + if (ahd_dmamem_alloc(ahd, scb_data->sense_dmat, + (void **)&sense_map->vaddr, + BUS_DMA_NOWAIT, &sense_map->dmamap) != 0) { + kfree(sense_map); + return; + } + + SLIST_INSERT_HEAD(&scb_data->sense_maps, sense_map, links); + + ahd_dmamap_load(ahd, scb_data->sense_dmat, sense_map->dmamap, + sense_map->vaddr, PAGE_SIZE, ahd_dmamap_cb, + &sense_map->physaddr, /*flags*/0); + + sense_data = sense_map->vaddr; + sense_busaddr = sense_map->physaddr; + scb_data->sense_left = PAGE_SIZE / AHD_SENSE_BUFSIZE; +#ifdef AHD_DEBUG + if (ahd_debug & AHD_SHOW_MEMORY) + printk("Mapped sense data\n"); +#endif + } + + newcount = min(scb_data->sense_left, scb_data->scbs_left); + newcount = min(newcount, scb_data->sgs_left); + newcount = min(newcount, (AHD_SCB_MAX_ALLOC - scb_data->numscbs)); + for (i = 0; i < newcount; i++) { + struct scb_platform_data *pdata; + u_int col_tag; + + next_scb = kmalloc(sizeof(*next_scb), GFP_ATOMIC); + if (next_scb == NULL) + break; + + pdata = kmalloc(sizeof(*pdata), GFP_ATOMIC); + if (pdata == NULL) { + kfree(next_scb); + break; + } + next_scb->platform_data = pdata; + next_scb->hscb_map = hscb_map; + next_scb->sg_map = sg_map; + next_scb->sense_map = sense_map; + next_scb->sg_list = segs; + next_scb->sense_data = sense_data; + next_scb->sense_busaddr = sense_busaddr; + memset(hscb, 0, sizeof(*hscb)); + next_scb->hscb = hscb; + hscb->hscb_busaddr = ahd_htole32(hscb_busaddr); + + /* + * The sequencer always starts with the second entry. + * The first entry is embedded in the scb. + */ + next_scb->sg_list_busaddr = sg_busaddr; + if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) + next_scb->sg_list_busaddr + += sizeof(struct ahd_dma64_seg); + else + next_scb->sg_list_busaddr += sizeof(struct ahd_dma_seg); + next_scb->ahd_softc = ahd; + next_scb->flags = SCB_FLAG_NONE; + next_scb->hscb->tag = ahd_htole16(scb_data->numscbs); + col_tag = scb_data->numscbs ^ 0x100; + next_scb->col_scb = ahd_find_scb_by_tag(ahd, col_tag); + if (next_scb->col_scb != NULL) + next_scb->col_scb->col_scb = next_scb; + ahd_free_scb(ahd, next_scb); + hscb++; + hscb_busaddr += sizeof(*hscb); + segs += ahd_sglist_size(ahd); + sg_busaddr += ahd_sglist_size(ahd); + sense_data += AHD_SENSE_BUFSIZE; + sense_busaddr += AHD_SENSE_BUFSIZE; + scb_data->numscbs++; + scb_data->sense_left--; + scb_data->scbs_left--; + scb_data->sgs_left--; + } +} + +void +ahd_controller_info(struct ahd_softc *ahd, char *buf) +{ + const char *speed; + const char *type; + int len; + + len = sprintf(buf, "%s: ", ahd_chip_names[ahd->chip & AHD_CHIPID_MASK]); + buf += len; + + speed = "Ultra320 "; + if ((ahd->features & AHD_WIDE) != 0) { + type = "Wide "; + } else { + type = "Single "; + } + len = sprintf(buf, "%s%sChannel %c, SCSI Id=%d, ", + speed, type, ahd->channel, ahd->our_id); + buf += len; + + sprintf(buf, "%s, %d SCBs", ahd->bus_description, + ahd->scb_data.maxhscbs); +} + +static const char *channel_strings[] = { + "Primary Low", + "Primary High", + "Secondary Low", + "Secondary High" +}; + +static const char *termstat_strings[] = { + "Terminated Correctly", + "Over Terminated", + "Under Terminated", + "Not Configured" +}; + +/***************************** Timer Facilities *******************************/ +static void +ahd_timer_reset(struct timer_list *timer, int usec) +{ + del_timer(timer); + timer->expires = jiffies + (usec * HZ)/1000000; + add_timer(timer); +} + +/* + * Start the board, ready for normal operation + */ +int +ahd_init(struct ahd_softc *ahd) +{ + uint8_t *next_vaddr; + dma_addr_t next_baddr; + size_t driver_data_size; + int i; + int error; + u_int warn_user; + uint8_t current_sensing; + uint8_t fstat; + + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + + ahd->stack_size = ahd_probe_stack_size(ahd); + ahd->saved_stack = kmalloc_array(ahd->stack_size, sizeof(uint16_t), + GFP_ATOMIC); + if (ahd->saved_stack == NULL) + return (ENOMEM); + + /* + * Verify that the compiler hasn't over-aggressively + * padded important structures. + */ + if (sizeof(struct hardware_scb) != 64) + panic("Hardware SCB size is incorrect"); + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_DEBUG_SEQUENCER) != 0) + ahd->flags |= AHD_SEQUENCER_DEBUG; +#endif + + /* + * Default to allowing initiator operations. + */ + ahd->flags |= AHD_INITIATORROLE; + + /* + * Only allow target mode features if this unit has them enabled. + */ + if ((AHD_TMODE_ENABLE & (0x1 << ahd->unit)) == 0) + ahd->features &= ~AHD_TARGETMODE; + + ahd->init_level++; + + /* + * DMA tag for our command fifos and other data in system memory + * the card's sequencer must be able to access. For initiator + * roles, we need to allocate space for the qoutfifo. When providing + * for the target mode role, we must additionally provide space for + * the incoming target command fifo. + */ + driver_data_size = AHD_SCB_MAX * sizeof(*ahd->qoutfifo) + + sizeof(struct hardware_scb); + if ((ahd->features & AHD_TARGETMODE) != 0) + driver_data_size += AHD_TMODE_CMDS * sizeof(struct target_cmd); + if ((ahd->bugs & AHD_PKT_BITBUCKET_BUG) != 0) + driver_data_size += PKT_OVERRUN_BUFSIZE; + if (ahd_dma_tag_create(ahd, ahd->parent_dmat, /*alignment*/1, + /*boundary*/BUS_SPACE_MAXADDR_32BIT + 1, + /*lowaddr*/BUS_SPACE_MAXADDR_32BIT, + /*highaddr*/BUS_SPACE_MAXADDR, + /*filter*/NULL, /*filterarg*/NULL, + driver_data_size, + /*nsegments*/1, + /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, + /*flags*/0, &ahd->shared_data_dmat) != 0) { + return (ENOMEM); + } + + ahd->init_level++; + + /* Allocation of driver data */ + if (ahd_dmamem_alloc(ahd, ahd->shared_data_dmat, + (void **)&ahd->shared_data_map.vaddr, + BUS_DMA_NOWAIT, + &ahd->shared_data_map.dmamap) != 0) { + return (ENOMEM); + } + + ahd->init_level++; + + /* And permanently map it in */ + ahd_dmamap_load(ahd, ahd->shared_data_dmat, ahd->shared_data_map.dmamap, + ahd->shared_data_map.vaddr, driver_data_size, + ahd_dmamap_cb, &ahd->shared_data_map.physaddr, + /*flags*/0); + ahd->qoutfifo = (struct ahd_completion *)ahd->shared_data_map.vaddr; + next_vaddr = (uint8_t *)&ahd->qoutfifo[AHD_QOUT_SIZE]; + next_baddr = ahd->shared_data_map.physaddr + + AHD_QOUT_SIZE*sizeof(struct ahd_completion); + if ((ahd->features & AHD_TARGETMODE) != 0) { + ahd->targetcmds = (struct target_cmd *)next_vaddr; + next_vaddr += AHD_TMODE_CMDS * sizeof(struct target_cmd); + next_baddr += AHD_TMODE_CMDS * sizeof(struct target_cmd); + } + + if ((ahd->bugs & AHD_PKT_BITBUCKET_BUG) != 0) { + ahd->overrun_buf = next_vaddr; + next_vaddr += PKT_OVERRUN_BUFSIZE; + next_baddr += PKT_OVERRUN_BUFSIZE; + } + + /* + * We need one SCB to serve as the "next SCB". Since the + * tag identifier in this SCB will never be used, there is + * no point in using a valid HSCB tag from an SCB pulled from + * the standard free pool. So, we allocate this "sentinel" + * specially from the DMA safe memory chunk used for the QOUTFIFO. + */ + ahd->next_queued_hscb = (struct hardware_scb *)next_vaddr; + ahd->next_queued_hscb_map = &ahd->shared_data_map; + ahd->next_queued_hscb->hscb_busaddr = ahd_htole32(next_baddr); + + ahd->init_level++; + + /* Allocate SCB data now that buffer_dmat is initialized */ + if (ahd_init_scbdata(ahd) != 0) + return (ENOMEM); + + if ((ahd->flags & AHD_INITIATORROLE) == 0) + ahd->flags &= ~AHD_RESET_BUS_A; + + /* + * Before committing these settings to the chip, give + * the OSM one last chance to modify our configuration. + */ + ahd_platform_init(ahd); + + /* Bring up the chip. */ + ahd_chip_init(ahd); + + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + + if ((ahd->flags & AHD_CURRENT_SENSING) == 0) + goto init_done; + + /* + * Verify termination based on current draw and + * warn user if the bus is over/under terminated. + */ + error = ahd_write_flexport(ahd, FLXADDR_ROMSTAT_CURSENSECTL, + CURSENSE_ENB); + if (error != 0) { + printk("%s: current sensing timeout 1\n", ahd_name(ahd)); + goto init_done; + } + for (i = 20, fstat = FLX_FSTAT_BUSY; + (fstat & FLX_FSTAT_BUSY) != 0 && i; i--) { + error = ahd_read_flexport(ahd, FLXADDR_FLEXSTAT, &fstat); + if (error != 0) { + printk("%s: current sensing timeout 2\n", + ahd_name(ahd)); + goto init_done; + } + } + if (i == 0) { + printk("%s: Timedout during current-sensing test\n", + ahd_name(ahd)); + goto init_done; + } + + /* Latch Current Sensing status. */ + error = ahd_read_flexport(ahd, FLXADDR_CURRENT_STAT, ¤t_sensing); + if (error != 0) { + printk("%s: current sensing timeout 3\n", ahd_name(ahd)); + goto init_done; + } + + /* Diable current sensing. */ + ahd_write_flexport(ahd, FLXADDR_ROMSTAT_CURSENSECTL, 0); + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_TERMCTL) != 0) { + printk("%s: current_sensing == 0x%x\n", + ahd_name(ahd), current_sensing); + } +#endif + warn_user = 0; + for (i = 0; i < 4; i++, current_sensing >>= FLX_CSTAT_SHIFT) { + u_int term_stat; + + term_stat = (current_sensing & FLX_CSTAT_MASK); + switch (term_stat) { + case FLX_CSTAT_OVER: + case FLX_CSTAT_UNDER: + warn_user++; + fallthrough; + case FLX_CSTAT_INVALID: + case FLX_CSTAT_OKAY: + if (warn_user == 0 && bootverbose == 0) + break; + printk("%s: %s Channel %s\n", ahd_name(ahd), + channel_strings[i], termstat_strings[term_stat]); + break; + } + } + if (warn_user) { + printk("%s: WARNING. Termination is not configured correctly.\n" + "%s: WARNING. SCSI bus operations may FAIL.\n", + ahd_name(ahd), ahd_name(ahd)); + } +init_done: + ahd_restart(ahd); + ahd_timer_reset(&ahd->stat_timer, AHD_STAT_UPDATE_US); + return (0); +} + +/* + * (Re)initialize chip state after a chip reset. + */ +static void +ahd_chip_init(struct ahd_softc *ahd) +{ + uint32_t busaddr; + u_int sxfrctl1; + u_int scsiseq_template; + u_int wait; + u_int i; + u_int target; + + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + /* + * Take the LED out of diagnostic mode + */ + ahd_outb(ahd, SBLKCTL, ahd_inb(ahd, SBLKCTL) & ~(DIAGLEDEN|DIAGLEDON)); + + /* + * Return HS_MAILBOX to its default value. + */ + ahd->hs_mailbox = 0; + ahd_outb(ahd, HS_MAILBOX, 0); + + /* Set the SCSI Id, SXFRCTL0, SXFRCTL1, and SIMODE1. */ + ahd_outb(ahd, IOWNID, ahd->our_id); + ahd_outb(ahd, TOWNID, ahd->our_id); + sxfrctl1 = (ahd->flags & AHD_TERM_ENB_A) != 0 ? STPWEN : 0; + sxfrctl1 |= (ahd->flags & AHD_SPCHK_ENB_A) != 0 ? ENSPCHK : 0; + if ((ahd->bugs & AHD_LONG_SETIMO_BUG) + && (ahd->seltime != STIMESEL_MIN)) { + /* + * The selection timer duration is twice as long + * as it should be. Halve it by adding "1" to + * the user specified setting. + */ + sxfrctl1 |= ahd->seltime + STIMESEL_BUG_ADJ; + } else { + sxfrctl1 |= ahd->seltime; + } + + ahd_outb(ahd, SXFRCTL0, DFON); + ahd_outb(ahd, SXFRCTL1, sxfrctl1|ahd->seltime|ENSTIMER|ACTNEGEN); + ahd_outb(ahd, SIMODE1, ENSELTIMO|ENSCSIRST|ENSCSIPERR); + + /* + * Now that termination is set, wait for up + * to 500ms for our transceivers to settle. If + * the adapter does not have a cable attached, + * the transceivers may never settle, so don't + * complain if we fail here. + */ + for (wait = 10000; + (ahd_inb(ahd, SBLKCTL) & (ENAB40|ENAB20)) == 0 && wait; + wait--) + ahd_delay(100); + + /* Clear any false bus resets due to the transceivers settling */ + ahd_outb(ahd, CLRSINT1, CLRSCSIRSTI); + ahd_outb(ahd, CLRINT, CLRSCSIINT); + + /* Initialize mode specific S/G state. */ + for (i = 0; i < 2; i++) { + ahd_set_modes(ahd, AHD_MODE_DFF0 + i, AHD_MODE_DFF0 + i); + ahd_outb(ahd, LONGJMP_ADDR + 1, INVALID_ADDR); + ahd_outb(ahd, SG_STATE, 0); + ahd_outb(ahd, CLRSEQINTSRC, 0xFF); + ahd_outb(ahd, SEQIMODE, + ENSAVEPTRS|ENCFG4DATA|ENCFG4ISTAT + |ENCFG4TSTAT|ENCFG4ICMD|ENCFG4TCMD); + } + + ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); + ahd_outb(ahd, DSCOMMAND0, ahd_inb(ahd, DSCOMMAND0)|MPARCKEN|CACHETHEN); + ahd_outb(ahd, DFF_THRSH, RD_DFTHRSH_75|WR_DFTHRSH_75); + ahd_outb(ahd, SIMODE0, ENIOERR|ENOVERRUN); + ahd_outb(ahd, SIMODE3, ENNTRAMPERR|ENOSRAMPERR); + if ((ahd->bugs & AHD_BUSFREEREV_BUG) != 0) { + ahd_outb(ahd, OPTIONMODE, AUTOACKEN|AUTO_MSGOUT_DE); + } else { + ahd_outb(ahd, OPTIONMODE, AUTOACKEN|BUSFREEREV|AUTO_MSGOUT_DE); + } + ahd_outb(ahd, SCSCHKN, CURRFIFODEF|WIDERESEN|SHVALIDSTDIS); + if ((ahd->chip & AHD_BUS_MASK) == AHD_PCIX) + /* + * Do not issue a target abort when a split completion + * error occurs. Let our PCIX interrupt handler deal + * with it instead. H2A4 Razor #625 + */ + ahd_outb(ahd, PCIXCTL, ahd_inb(ahd, PCIXCTL) | SPLTSTADIS); + + if ((ahd->bugs & AHD_LQOOVERRUN_BUG) != 0) + ahd_outb(ahd, LQOSCSCTL, LQONOCHKOVER); + + /* + * Tweak IOCELL settings. + */ + if ((ahd->flags & AHD_HP_BOARD) != 0) { + for (i = 0; i < NUMDSPS; i++) { + ahd_outb(ahd, DSPSELECT, i); + ahd_outb(ahd, WRTBIASCTL, WRTBIASCTL_HP_DEFAULT); + } +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MISC) != 0) + printk("%s: WRTBIASCTL now 0x%x\n", ahd_name(ahd), + WRTBIASCTL_HP_DEFAULT); +#endif + } + ahd_setup_iocell_workaround(ahd); + + /* + * Enable LQI Manager interrupts. + */ + ahd_outb(ahd, LQIMODE1, ENLQIPHASE_LQ|ENLQIPHASE_NLQ|ENLIQABORT + | ENLQICRCI_LQ|ENLQICRCI_NLQ|ENLQIBADLQI + | ENLQIOVERI_LQ|ENLQIOVERI_NLQ); + ahd_outb(ahd, LQOMODE0, ENLQOATNLQ|ENLQOATNPKT|ENLQOTCRC); + /* + * We choose to have the sequencer catch LQOPHCHGINPKT errors + * manually for the command phase at the start of a packetized + * selection case. ENLQOBUSFREE should be made redundant by + * the BUSFREE interrupt, but it seems that some LQOBUSFREE + * events fail to assert the BUSFREE interrupt so we must + * also enable LQOBUSFREE interrupts. + */ + ahd_outb(ahd, LQOMODE1, ENLQOBUSFREE); + + /* + * Setup sequencer interrupt handlers. + */ + ahd_outw(ahd, INTVEC1_ADDR, ahd_resolve_seqaddr(ahd, LABEL_seq_isr)); + ahd_outw(ahd, INTVEC2_ADDR, ahd_resolve_seqaddr(ahd, LABEL_timer_isr)); + + /* + * Setup SCB Offset registers. + */ + if ((ahd->bugs & AHD_PKT_LUN_BUG) != 0) { + ahd_outb(ahd, LUNPTR, offsetof(struct hardware_scb, + pkt_long_lun)); + } else { + ahd_outb(ahd, LUNPTR, offsetof(struct hardware_scb, lun)); + } + ahd_outb(ahd, CMDLENPTR, offsetof(struct hardware_scb, cdb_len)); + ahd_outb(ahd, ATTRPTR, offsetof(struct hardware_scb, task_attribute)); + ahd_outb(ahd, FLAGPTR, offsetof(struct hardware_scb, task_management)); + ahd_outb(ahd, CMDPTR, offsetof(struct hardware_scb, + shared_data.idata.cdb)); + ahd_outb(ahd, QNEXTPTR, + offsetof(struct hardware_scb, next_hscb_busaddr)); + ahd_outb(ahd, ABRTBITPTR, MK_MESSAGE_BIT_OFFSET); + ahd_outb(ahd, ABRTBYTEPTR, offsetof(struct hardware_scb, control)); + if ((ahd->bugs & AHD_PKT_LUN_BUG) != 0) { + ahd_outb(ahd, LUNLEN, + sizeof(ahd->next_queued_hscb->pkt_long_lun) - 1); + } else { + ahd_outb(ahd, LUNLEN, LUNLEN_SINGLE_LEVEL_LUN); + } + ahd_outb(ahd, CDBLIMIT, SCB_CDB_LEN_PTR - 1); + ahd_outb(ahd, MAXCMD, 0xFF); + ahd_outb(ahd, SCBAUTOPTR, + AUSCBPTR_EN | offsetof(struct hardware_scb, tag)); + + /* We haven't been enabled for target mode yet. */ + ahd_outb(ahd, MULTARGID, 0); + ahd_outb(ahd, MULTARGID + 1, 0); + + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + /* Initialize the negotiation table. */ + if ((ahd->features & AHD_NEW_IOCELL_OPTS) == 0) { + /* + * Clear the spare bytes in the neg table to avoid + * spurious parity errors. + */ + for (target = 0; target < AHD_NUM_TARGETS; target++) { + ahd_outb(ahd, NEGOADDR, target); + ahd_outb(ahd, ANNEXCOL, AHD_ANNEXCOL_PER_DEV0); + for (i = 0; i < AHD_NUM_PER_DEV_ANNEXCOLS; i++) + ahd_outb(ahd, ANNEXDAT, 0); + } + } + for (target = 0; target < AHD_NUM_TARGETS; target++) { + struct ahd_devinfo devinfo; + struct ahd_initiator_tinfo *tinfo; + struct ahd_tmode_tstate *tstate; + + tinfo = ahd_fetch_transinfo(ahd, 'A', ahd->our_id, + target, &tstate); + ahd_compile_devinfo(&devinfo, ahd->our_id, + target, CAM_LUN_WILDCARD, + 'A', ROLE_INITIATOR); + ahd_update_neg_table(ahd, &devinfo, &tinfo->curr); + } + + ahd_outb(ahd, CLRSINT3, NTRAMPERR|OSRAMPERR); + ahd_outb(ahd, CLRINT, CLRSCSIINT); + +#ifdef NEEDS_MORE_TESTING + /* + * Always enable abort on incoming L_Qs if this feature is + * supported. We use this to catch invalid SCB references. + */ + if ((ahd->bugs & AHD_ABORT_LQI_BUG) == 0) + ahd_outb(ahd, LQCTL1, ABORTPENDING); + else +#endif + ahd_outb(ahd, LQCTL1, 0); + + /* All of our queues are empty */ + ahd->qoutfifonext = 0; + ahd->qoutfifonext_valid_tag = QOUTFIFO_ENTRY_VALID; + ahd_outb(ahd, QOUTFIFO_ENTRY_VALID_TAG, QOUTFIFO_ENTRY_VALID); + for (i = 0; i < AHD_QOUT_SIZE; i++) + ahd->qoutfifo[i].valid_tag = 0; + ahd_sync_qoutfifo(ahd, BUS_DMASYNC_PREREAD); + + ahd->qinfifonext = 0; + for (i = 0; i < AHD_QIN_SIZE; i++) + ahd->qinfifo[i] = SCB_LIST_NULL; + + if ((ahd->features & AHD_TARGETMODE) != 0) { + /* All target command blocks start out invalid. */ + for (i = 0; i < AHD_TMODE_CMDS; i++) + ahd->targetcmds[i].cmd_valid = 0; + ahd_sync_tqinfifo(ahd, BUS_DMASYNC_PREREAD); + ahd->tqinfifonext = 1; + ahd_outb(ahd, KERNEL_TQINPOS, ahd->tqinfifonext - 1); + ahd_outb(ahd, TQINPOS, ahd->tqinfifonext); + } + + /* Initialize Scratch Ram. */ + ahd_outb(ahd, SEQ_FLAGS, 0); + ahd_outb(ahd, SEQ_FLAGS2, 0); + + /* We don't have any waiting selections */ + ahd_outw(ahd, WAITING_TID_HEAD, SCB_LIST_NULL); + ahd_outw(ahd, WAITING_TID_TAIL, SCB_LIST_NULL); + ahd_outw(ahd, MK_MESSAGE_SCB, SCB_LIST_NULL); + ahd_outw(ahd, MK_MESSAGE_SCSIID, 0xFF); + for (i = 0; i < AHD_NUM_TARGETS; i++) + ahd_outw(ahd, WAITING_SCB_TAILS + (2 * i), SCB_LIST_NULL); + + /* + * Nobody is waiting to be DMAed into the QOUTFIFO. + */ + ahd_outw(ahd, COMPLETE_SCB_HEAD, SCB_LIST_NULL); + ahd_outw(ahd, COMPLETE_SCB_DMAINPROG_HEAD, SCB_LIST_NULL); + ahd_outw(ahd, COMPLETE_DMA_SCB_HEAD, SCB_LIST_NULL); + ahd_outw(ahd, COMPLETE_DMA_SCB_TAIL, SCB_LIST_NULL); + ahd_outw(ahd, COMPLETE_ON_QFREEZE_HEAD, SCB_LIST_NULL); + + /* + * The Freeze Count is 0. + */ + ahd->qfreeze_cnt = 0; + ahd_outw(ahd, QFREEZE_COUNT, 0); + ahd_outw(ahd, KERNEL_QFREEZE_COUNT, 0); + + /* + * Tell the sequencer where it can find our arrays in memory. + */ + busaddr = ahd->shared_data_map.physaddr; + ahd_outl(ahd, SHARED_DATA_ADDR, busaddr); + ahd_outl(ahd, QOUTFIFO_NEXT_ADDR, busaddr); + + /* + * Setup the allowed SCSI Sequences based on operational mode. + * If we are a target, we'll enable select in operations once + * we've had a lun enabled. + */ + scsiseq_template = ENAUTOATNP; + if ((ahd->flags & AHD_INITIATORROLE) != 0) + scsiseq_template |= ENRSELI; + ahd_outb(ahd, SCSISEQ_TEMPLATE, scsiseq_template); + + /* There are no busy SCBs yet. */ + for (target = 0; target < AHD_NUM_TARGETS; target++) { + int lun; + + for (lun = 0; lun < AHD_NUM_LUNS_NONPKT; lun++) + ahd_unbusy_tcl(ahd, BUILD_TCL_RAW(target, 'A', lun)); + } + + /* + * Initialize the group code to command length table. + * Vendor Unique codes are set to 0 so we only capture + * the first byte of the cdb. These can be overridden + * when target mode is enabled. + */ + ahd_outb(ahd, CMDSIZE_TABLE, 5); + ahd_outb(ahd, CMDSIZE_TABLE + 1, 9); + ahd_outb(ahd, CMDSIZE_TABLE + 2, 9); + ahd_outb(ahd, CMDSIZE_TABLE + 3, 0); + ahd_outb(ahd, CMDSIZE_TABLE + 4, 15); + ahd_outb(ahd, CMDSIZE_TABLE + 5, 11); + ahd_outb(ahd, CMDSIZE_TABLE + 6, 0); + ahd_outb(ahd, CMDSIZE_TABLE + 7, 0); + + /* Tell the sequencer of our initial queue positions */ + ahd_set_modes(ahd, AHD_MODE_CCHAN, AHD_MODE_CCHAN); + ahd_outb(ahd, QOFF_CTLSTA, SCB_QSIZE_512); + ahd->qinfifonext = 0; + ahd_set_hnscb_qoff(ahd, ahd->qinfifonext); + ahd_set_hescb_qoff(ahd, 0); + ahd_set_snscb_qoff(ahd, 0); + ahd_set_sescb_qoff(ahd, 0); + ahd_set_sdscb_qoff(ahd, 0); + + /* + * Tell the sequencer which SCB will be the next one it receives. + */ + busaddr = ahd_le32toh(ahd->next_queued_hscb->hscb_busaddr); + ahd_outl(ahd, NEXT_QUEUED_SCB_ADDR, busaddr); + + /* + * Default to coalescing disabled. + */ + ahd_outw(ahd, INT_COALESCING_CMDCOUNT, 0); + ahd_outw(ahd, CMDS_PENDING, 0); + ahd_update_coalescing_values(ahd, ahd->int_coalescing_timer, + ahd->int_coalescing_maxcmds, + ahd->int_coalescing_mincmds); + ahd_enable_coalescing(ahd, FALSE); + + ahd_loadseq(ahd); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + + if (ahd->features & AHD_AIC79XXB_SLOWCRC) { + u_int negodat3 = ahd_inb(ahd, NEGCONOPTS); + + negodat3 |= ENSLOWCRC; + ahd_outb(ahd, NEGCONOPTS, negodat3); + negodat3 = ahd_inb(ahd, NEGCONOPTS); + if (!(negodat3 & ENSLOWCRC)) + printk("aic79xx: failed to set the SLOWCRC bit\n"); + else + printk("aic79xx: SLOWCRC bit set\n"); + } +} + +/* + * Setup default device and controller settings. + * This should only be called if our probe has + * determined that no configuration data is available. + */ +int +ahd_default_config(struct ahd_softc *ahd) +{ + int targ; + + ahd->our_id = 7; + + /* + * Allocate a tstate to house information for our + * initiator presence on the bus as well as the user + * data for any target mode initiator. + */ + if (ahd_alloc_tstate(ahd, ahd->our_id, 'A') == NULL) { + printk("%s: unable to allocate ahd_tmode_tstate. " + "Failing attach\n", ahd_name(ahd)); + return (ENOMEM); + } + + for (targ = 0; targ < AHD_NUM_TARGETS; targ++) { + struct ahd_devinfo devinfo; + struct ahd_initiator_tinfo *tinfo; + struct ahd_tmode_tstate *tstate; + uint16_t target_mask; + + tinfo = ahd_fetch_transinfo(ahd, 'A', ahd->our_id, + targ, &tstate); + /* + * We support SPC2 and SPI4. + */ + tinfo->user.protocol_version = 4; + tinfo->user.transport_version = 4; + + target_mask = 0x01 << targ; + ahd->user_discenable |= target_mask; + tstate->discenable |= target_mask; + ahd->user_tagenable |= target_mask; +#ifdef AHD_FORCE_160 + tinfo->user.period = AHD_SYNCRATE_DT; +#else + tinfo->user.period = AHD_SYNCRATE_160; +#endif + tinfo->user.offset = MAX_OFFSET; + tinfo->user.ppr_options = MSG_EXT_PPR_RD_STRM + | MSG_EXT_PPR_WR_FLOW + | MSG_EXT_PPR_HOLD_MCS + | MSG_EXT_PPR_IU_REQ + | MSG_EXT_PPR_QAS_REQ + | MSG_EXT_PPR_DT_REQ; + if ((ahd->features & AHD_RTI) != 0) + tinfo->user.ppr_options |= MSG_EXT_PPR_RTI; + + tinfo->user.width = MSG_EXT_WDTR_BUS_16_BIT; + + /* + * Start out Async/Narrow/Untagged and with + * conservative protocol support. + */ + tinfo->goal.protocol_version = 2; + tinfo->goal.transport_version = 2; + tinfo->curr.protocol_version = 2; + tinfo->curr.transport_version = 2; + ahd_compile_devinfo(&devinfo, ahd->our_id, + targ, CAM_LUN_WILDCARD, + 'A', ROLE_INITIATOR); + tstate->tagenable &= ~target_mask; + ahd_set_width(ahd, &devinfo, MSG_EXT_WDTR_BUS_8_BIT, + AHD_TRANS_CUR|AHD_TRANS_GOAL, /*paused*/TRUE); + ahd_set_syncrate(ahd, &devinfo, /*period*/0, /*offset*/0, + /*ppr_options*/0, AHD_TRANS_CUR|AHD_TRANS_GOAL, + /*paused*/TRUE); + } + return (0); +} + +/* + * Parse device configuration information. + */ +int +ahd_parse_cfgdata(struct ahd_softc *ahd, struct seeprom_config *sc) +{ + int targ; + int max_targ; + + max_targ = sc->max_targets & CFMAXTARG; + ahd->our_id = sc->brtime_id & CFSCSIID; + + /* + * Allocate a tstate to house information for our + * initiator presence on the bus as well as the user + * data for any target mode initiator. + */ + if (ahd_alloc_tstate(ahd, ahd->our_id, 'A') == NULL) { + printk("%s: unable to allocate ahd_tmode_tstate. " + "Failing attach\n", ahd_name(ahd)); + return (ENOMEM); + } + + for (targ = 0; targ < max_targ; targ++) { + struct ahd_devinfo devinfo; + struct ahd_initiator_tinfo *tinfo; + struct ahd_transinfo *user_tinfo; + struct ahd_tmode_tstate *tstate; + uint16_t target_mask; + + tinfo = ahd_fetch_transinfo(ahd, 'A', ahd->our_id, + targ, &tstate); + user_tinfo = &tinfo->user; + + /* + * We support SPC2 and SPI4. + */ + tinfo->user.protocol_version = 4; + tinfo->user.transport_version = 4; + + target_mask = 0x01 << targ; + ahd->user_discenable &= ~target_mask; + tstate->discenable &= ~target_mask; + ahd->user_tagenable &= ~target_mask; + if (sc->device_flags[targ] & CFDISC) { + tstate->discenable |= target_mask; + ahd->user_discenable |= target_mask; + ahd->user_tagenable |= target_mask; + } else { + /* + * Cannot be packetized without disconnection. + */ + sc->device_flags[targ] &= ~CFPACKETIZED; + } + + user_tinfo->ppr_options = 0; + user_tinfo->period = (sc->device_flags[targ] & CFXFER); + if (user_tinfo->period < CFXFER_ASYNC) { + if (user_tinfo->period <= AHD_PERIOD_10MHz) + user_tinfo->ppr_options |= MSG_EXT_PPR_DT_REQ; + user_tinfo->offset = MAX_OFFSET; + } else { + user_tinfo->offset = 0; + user_tinfo->period = AHD_ASYNC_XFER_PERIOD; + } +#ifdef AHD_FORCE_160 + if (user_tinfo->period <= AHD_SYNCRATE_160) + user_tinfo->period = AHD_SYNCRATE_DT; +#endif + + if ((sc->device_flags[targ] & CFPACKETIZED) != 0) { + user_tinfo->ppr_options |= MSG_EXT_PPR_RD_STRM + | MSG_EXT_PPR_WR_FLOW + | MSG_EXT_PPR_HOLD_MCS + | MSG_EXT_PPR_IU_REQ; + if ((ahd->features & AHD_RTI) != 0) + user_tinfo->ppr_options |= MSG_EXT_PPR_RTI; + } + + if ((sc->device_flags[targ] & CFQAS) != 0) + user_tinfo->ppr_options |= MSG_EXT_PPR_QAS_REQ; + + if ((sc->device_flags[targ] & CFWIDEB) != 0) + user_tinfo->width = MSG_EXT_WDTR_BUS_16_BIT; + else + user_tinfo->width = MSG_EXT_WDTR_BUS_8_BIT; +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MISC) != 0) + printk("(%d): %x:%x:%x:%x\n", targ, user_tinfo->width, + user_tinfo->period, user_tinfo->offset, + user_tinfo->ppr_options); +#endif + /* + * Start out Async/Narrow/Untagged and with + * conservative protocol support. + */ + tstate->tagenable &= ~target_mask; + tinfo->goal.protocol_version = 2; + tinfo->goal.transport_version = 2; + tinfo->curr.protocol_version = 2; + tinfo->curr.transport_version = 2; + ahd_compile_devinfo(&devinfo, ahd->our_id, + targ, CAM_LUN_WILDCARD, + 'A', ROLE_INITIATOR); + ahd_set_width(ahd, &devinfo, MSG_EXT_WDTR_BUS_8_BIT, + AHD_TRANS_CUR|AHD_TRANS_GOAL, /*paused*/TRUE); + ahd_set_syncrate(ahd, &devinfo, /*period*/0, /*offset*/0, + /*ppr_options*/0, AHD_TRANS_CUR|AHD_TRANS_GOAL, + /*paused*/TRUE); + } + + ahd->flags &= ~AHD_SPCHK_ENB_A; + if (sc->bios_control & CFSPARITY) + ahd->flags |= AHD_SPCHK_ENB_A; + + ahd->flags &= ~AHD_RESET_BUS_A; + if (sc->bios_control & CFRESETB) + ahd->flags |= AHD_RESET_BUS_A; + + ahd->flags &= ~AHD_EXTENDED_TRANS_A; + if (sc->bios_control & CFEXTEND) + ahd->flags |= AHD_EXTENDED_TRANS_A; + + ahd->flags &= ~AHD_BIOS_ENABLED; + if ((sc->bios_control & CFBIOSSTATE) == CFBS_ENABLED) + ahd->flags |= AHD_BIOS_ENABLED; + + ahd->flags &= ~AHD_STPWLEVEL_A; + if ((sc->adapter_control & CFSTPWLEVEL) != 0) + ahd->flags |= AHD_STPWLEVEL_A; + + return (0); +} + +/* + * Parse device configuration information. + */ +int +ahd_parse_vpddata(struct ahd_softc *ahd, struct vpd_config *vpd) +{ + int error; + + error = ahd_verify_vpd_cksum(vpd); + if (error == 0) + return (EINVAL); + if ((vpd->bios_flags & VPDBOOTHOST) != 0) + ahd->flags |= AHD_BOOT_CHANNEL; + return (0); +} + +void +ahd_intr_enable(struct ahd_softc *ahd, int enable) +{ + u_int hcntrl; + + hcntrl = ahd_inb(ahd, HCNTRL); + hcntrl &= ~INTEN; + ahd->pause &= ~INTEN; + ahd->unpause &= ~INTEN; + if (enable) { + hcntrl |= INTEN; + ahd->pause |= INTEN; + ahd->unpause |= INTEN; + } + ahd_outb(ahd, HCNTRL, hcntrl); +} + +static void +ahd_update_coalescing_values(struct ahd_softc *ahd, u_int timer, u_int maxcmds, + u_int mincmds) +{ + if (timer > AHD_TIMER_MAX_US) + timer = AHD_TIMER_MAX_US; + ahd->int_coalescing_timer = timer; + + if (maxcmds > AHD_INT_COALESCING_MAXCMDS_MAX) + maxcmds = AHD_INT_COALESCING_MAXCMDS_MAX; + if (mincmds > AHD_INT_COALESCING_MINCMDS_MAX) + mincmds = AHD_INT_COALESCING_MINCMDS_MAX; + ahd->int_coalescing_maxcmds = maxcmds; + ahd_outw(ahd, INT_COALESCING_TIMER, timer / AHD_TIMER_US_PER_TICK); + ahd_outb(ahd, INT_COALESCING_MAXCMDS, -maxcmds); + ahd_outb(ahd, INT_COALESCING_MINCMDS, -mincmds); +} + +static void +ahd_enable_coalescing(struct ahd_softc *ahd, int enable) +{ + + ahd->hs_mailbox &= ~ENINT_COALESCE; + if (enable) + ahd->hs_mailbox |= ENINT_COALESCE; + ahd_outb(ahd, HS_MAILBOX, ahd->hs_mailbox); + ahd_flush_device_writes(ahd); + ahd_run_qoutfifo(ahd); +} + +/* + * Ensure that the card is paused in a location + * outside of all critical sections and that all + * pending work is completed prior to returning. + * This routine should only be called from outside + * an interrupt context. + */ +void +ahd_pause_and_flushwork(struct ahd_softc *ahd) +{ + u_int intstat; + u_int maxloops; + + maxloops = 1000; + ahd->flags |= AHD_ALL_INTERRUPTS; + ahd_pause(ahd); + /* + * Freeze the outgoing selections. We do this only + * until we are safely paused without further selections + * pending. + */ + ahd->qfreeze_cnt--; + ahd_outw(ahd, KERNEL_QFREEZE_COUNT, ahd->qfreeze_cnt); + ahd_outb(ahd, SEQ_FLAGS2, ahd_inb(ahd, SEQ_FLAGS2) | SELECTOUT_QFROZEN); + do { + + ahd_unpause(ahd); + /* + * Give the sequencer some time to service + * any active selections. + */ + ahd_delay(500); + + ahd_intr(ahd); + ahd_pause(ahd); + intstat = ahd_inb(ahd, INTSTAT); + if ((intstat & INT_PEND) == 0) { + ahd_clear_critical_section(ahd); + intstat = ahd_inb(ahd, INTSTAT); + } + } while (--maxloops + && (intstat != 0xFF || (ahd->features & AHD_REMOVABLE) == 0) + && ((intstat & INT_PEND) != 0 + || (ahd_inb(ahd, SCSISEQ0) & ENSELO) != 0 + || (ahd_inb(ahd, SSTAT0) & (SELDO|SELINGO)) != 0)); + + if (maxloops == 0) { + printk("Infinite interrupt loop, INTSTAT = %x", + ahd_inb(ahd, INTSTAT)); + } + ahd->qfreeze_cnt++; + ahd_outw(ahd, KERNEL_QFREEZE_COUNT, ahd->qfreeze_cnt); + + ahd_flush_qoutfifo(ahd); + + ahd->flags &= ~AHD_ALL_INTERRUPTS; +} + +#ifdef CONFIG_PM +int +ahd_suspend(struct ahd_softc *ahd) +{ + + ahd_pause_and_flushwork(ahd); + + if (LIST_FIRST(&ahd->pending_scbs) != NULL) { + ahd_unpause(ahd); + return (EBUSY); + } + ahd_shutdown(ahd); + return (0); +} + +void +ahd_resume(struct ahd_softc *ahd) +{ + + ahd_reset(ahd, /*reinit*/TRUE); + ahd_intr_enable(ahd, TRUE); + ahd_restart(ahd); +} +#endif + +/************************** Busy Target Table *********************************/ +/* + * Set SCBPTR to the SCB that contains the busy + * table entry for TCL. Return the offset into + * the SCB that contains the entry for TCL. + * saved_scbid is dereferenced and set to the + * scbid that should be restored once manipualtion + * of the TCL entry is complete. + */ +static inline u_int +ahd_index_busy_tcl(struct ahd_softc *ahd, u_int *saved_scbid, u_int tcl) +{ + /* + * Index to the SCB that contains the busy entry. + */ + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + *saved_scbid = ahd_get_scbptr(ahd); + ahd_set_scbptr(ahd, TCL_LUN(tcl) + | ((TCL_TARGET_OFFSET(tcl) & 0xC) << 4)); + + /* + * And now calculate the SCB offset to the entry. + * Each entry is 2 bytes wide, hence the + * multiplication by 2. + */ + return (((TCL_TARGET_OFFSET(tcl) & 0x3) << 1) + SCB_DISCONNECTED_LISTS); +} + +/* + * Return the untagged transaction id for a given target/channel lun. + */ +static u_int +ahd_find_busy_tcl(struct ahd_softc *ahd, u_int tcl) +{ + u_int scbid; + u_int scb_offset; + u_int saved_scbptr; + + scb_offset = ahd_index_busy_tcl(ahd, &saved_scbptr, tcl); + scbid = ahd_inw_scbram(ahd, scb_offset); + ahd_set_scbptr(ahd, saved_scbptr); + return (scbid); +} + +static void +ahd_busy_tcl(struct ahd_softc *ahd, u_int tcl, u_int scbid) +{ + u_int scb_offset; + u_int saved_scbptr; + + scb_offset = ahd_index_busy_tcl(ahd, &saved_scbptr, tcl); + ahd_outw(ahd, scb_offset, scbid); + ahd_set_scbptr(ahd, saved_scbptr); +} + +/************************** SCB and SCB queue management **********************/ +static int +ahd_match_scb(struct ahd_softc *ahd, struct scb *scb, int target, + char channel, int lun, u_int tag, role_t role) +{ + int targ = SCB_GET_TARGET(ahd, scb); + char chan = SCB_GET_CHANNEL(ahd, scb); + int slun = SCB_GET_LUN(scb); + int match; + + match = ((chan == channel) || (channel == ALL_CHANNELS)); + if (match != 0) + match = ((targ == target) || (target == CAM_TARGET_WILDCARD)); + if (match != 0) + match = ((lun == slun) || (lun == CAM_LUN_WILDCARD)); + if (match != 0) { +#ifdef AHD_TARGET_MODE + int group; + + group = XPT_FC_GROUP(scb->io_ctx->ccb_h.func_code); + if (role == ROLE_INITIATOR) { + match = (group != XPT_FC_GROUP_TMODE) + && ((tag == SCB_GET_TAG(scb)) + || (tag == SCB_LIST_NULL)); + } else if (role == ROLE_TARGET) { + match = (group == XPT_FC_GROUP_TMODE) + && ((tag == scb->io_ctx->csio.tag_id) + || (tag == SCB_LIST_NULL)); + } +#else /* !AHD_TARGET_MODE */ + match = ((tag == SCB_GET_TAG(scb)) || (tag == SCB_LIST_NULL)); +#endif /* AHD_TARGET_MODE */ + } + + return match; +} + +static void +ahd_freeze_devq(struct ahd_softc *ahd, struct scb *scb) +{ + int target; + char channel; + int lun; + + target = SCB_GET_TARGET(ahd, scb); + lun = SCB_GET_LUN(scb); + channel = SCB_GET_CHANNEL(ahd, scb); + + ahd_search_qinfifo(ahd, target, channel, lun, + /*tag*/SCB_LIST_NULL, ROLE_UNKNOWN, + CAM_REQUEUE_REQ, SEARCH_COMPLETE); + + ahd_platform_freeze_devq(ahd, scb); +} + +void +ahd_qinfifo_requeue_tail(struct ahd_softc *ahd, struct scb *scb) +{ + struct scb *prev_scb; + ahd_mode_state saved_modes; + + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_CCHAN, AHD_MODE_CCHAN); + prev_scb = NULL; + if (ahd_qinfifo_count(ahd) != 0) { + u_int prev_tag; + u_int prev_pos; + + prev_pos = AHD_QIN_WRAP(ahd->qinfifonext - 1); + prev_tag = ahd->qinfifo[prev_pos]; + prev_scb = ahd_lookup_scb(ahd, prev_tag); + } + ahd_qinfifo_requeue(ahd, prev_scb, scb); + ahd_set_hnscb_qoff(ahd, ahd->qinfifonext); + ahd_restore_modes(ahd, saved_modes); +} + +static void +ahd_qinfifo_requeue(struct ahd_softc *ahd, struct scb *prev_scb, + struct scb *scb) +{ + if (prev_scb == NULL) { + uint32_t busaddr; + + busaddr = ahd_le32toh(scb->hscb->hscb_busaddr); + ahd_outl(ahd, NEXT_QUEUED_SCB_ADDR, busaddr); + } else { + prev_scb->hscb->next_hscb_busaddr = scb->hscb->hscb_busaddr; + ahd_sync_scb(ahd, prev_scb, + BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); + } + ahd->qinfifo[AHD_QIN_WRAP(ahd->qinfifonext)] = SCB_GET_TAG(scb); + ahd->qinfifonext++; + scb->hscb->next_hscb_busaddr = ahd->next_queued_hscb->hscb_busaddr; + ahd_sync_scb(ahd, scb, BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); +} + +static int +ahd_qinfifo_count(struct ahd_softc *ahd) +{ + u_int qinpos; + u_int wrap_qinpos; + u_int wrap_qinfifonext; + + AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK); + qinpos = ahd_get_snscb_qoff(ahd); + wrap_qinpos = AHD_QIN_WRAP(qinpos); + wrap_qinfifonext = AHD_QIN_WRAP(ahd->qinfifonext); + if (wrap_qinfifonext >= wrap_qinpos) + return (wrap_qinfifonext - wrap_qinpos); + else + return (wrap_qinfifonext + + ARRAY_SIZE(ahd->qinfifo) - wrap_qinpos); +} + +static void +ahd_reset_cmds_pending(struct ahd_softc *ahd) +{ + struct scb *scb; + ahd_mode_state saved_modes; + u_int pending_cmds; + + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_CCHAN, AHD_MODE_CCHAN); + + /* + * Don't count any commands as outstanding that the + * sequencer has already marked for completion. + */ + ahd_flush_qoutfifo(ahd); + + pending_cmds = 0; + LIST_FOREACH(scb, &ahd->pending_scbs, pending_links) { + pending_cmds++; + } + ahd_outw(ahd, CMDS_PENDING, pending_cmds - ahd_qinfifo_count(ahd)); + ahd_restore_modes(ahd, saved_modes); + ahd->flags &= ~AHD_UPDATE_PEND_CMDS; +} + +static void +ahd_done_with_status(struct ahd_softc *ahd, struct scb *scb, uint32_t status) +{ + cam_status ostat; + cam_status cstat; + + ostat = ahd_get_transaction_status(scb); + if (ostat == CAM_REQ_INPROG) + ahd_set_transaction_status(scb, status); + cstat = ahd_get_transaction_status(scb); + if (cstat != CAM_REQ_CMP) + ahd_freeze_scb(scb); + ahd_done(ahd, scb); +} + +int +ahd_search_qinfifo(struct ahd_softc *ahd, int target, char channel, + int lun, u_int tag, role_t role, uint32_t status, + ahd_search_action action) +{ + struct scb *scb; + struct scb *mk_msg_scb; + struct scb *prev_scb; + ahd_mode_state saved_modes; + u_int qinstart; + u_int qinpos; + u_int qintail; + u_int tid_next; + u_int tid_prev; + u_int scbid; + u_int seq_flags2; + u_int savedscbptr; + uint32_t busaddr; + int found; + int targets; + + /* Must be in CCHAN mode */ + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_CCHAN, AHD_MODE_CCHAN); + + /* + * Halt any pending SCB DMA. The sequencer will reinitiate + * this dma if the qinfifo is not empty once we unpause. + */ + if ((ahd_inb(ahd, CCSCBCTL) & (CCARREN|CCSCBEN|CCSCBDIR)) + == (CCARREN|CCSCBEN|CCSCBDIR)) { + ahd_outb(ahd, CCSCBCTL, + ahd_inb(ahd, CCSCBCTL) & ~(CCARREN|CCSCBEN)); + while ((ahd_inb(ahd, CCSCBCTL) & (CCARREN|CCSCBEN)) != 0) + ; + } + /* Determine sequencer's position in the qinfifo. */ + qintail = AHD_QIN_WRAP(ahd->qinfifonext); + qinstart = ahd_get_snscb_qoff(ahd); + qinpos = AHD_QIN_WRAP(qinstart); + found = 0; + prev_scb = NULL; + + if (action == SEARCH_PRINT) { + printk("qinstart = %d qinfifonext = %d\nQINFIFO:", + qinstart, ahd->qinfifonext); + } + + /* + * Start with an empty queue. Entries that are not chosen + * for removal will be re-added to the queue as we go. + */ + ahd->qinfifonext = qinstart; + busaddr = ahd_le32toh(ahd->next_queued_hscb->hscb_busaddr); + ahd_outl(ahd, NEXT_QUEUED_SCB_ADDR, busaddr); + + while (qinpos != qintail) { + scb = ahd_lookup_scb(ahd, ahd->qinfifo[qinpos]); + if (scb == NULL) { + printk("qinpos = %d, SCB index = %d\n", + qinpos, ahd->qinfifo[qinpos]); + panic("Loop 1\n"); + } + + if (ahd_match_scb(ahd, scb, target, channel, lun, tag, role)) { + /* + * We found an scb that needs to be acted on. + */ + found++; + switch (action) { + case SEARCH_COMPLETE: + if ((scb->flags & SCB_ACTIVE) == 0) + printk("Inactive SCB in qinfifo\n"); + ahd_done_with_status(ahd, scb, status); + fallthrough; + case SEARCH_REMOVE: + break; + case SEARCH_PRINT: + printk(" 0x%x", ahd->qinfifo[qinpos]); + fallthrough; + case SEARCH_COUNT: + ahd_qinfifo_requeue(ahd, prev_scb, scb); + prev_scb = scb; + break; + } + } else { + ahd_qinfifo_requeue(ahd, prev_scb, scb); + prev_scb = scb; + } + qinpos = AHD_QIN_WRAP(qinpos+1); + } + + ahd_set_hnscb_qoff(ahd, ahd->qinfifonext); + + if (action == SEARCH_PRINT) + printk("\nWAITING_TID_QUEUES:\n"); + + /* + * Search waiting for selection lists. We traverse the + * list of "their ids" waiting for selection and, if + * appropriate, traverse the SCBs of each "their id" + * looking for matches. + */ + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + seq_flags2 = ahd_inb(ahd, SEQ_FLAGS2); + if ((seq_flags2 & PENDING_MK_MESSAGE) != 0) { + scbid = ahd_inw(ahd, MK_MESSAGE_SCB); + mk_msg_scb = ahd_lookup_scb(ahd, scbid); + } else + mk_msg_scb = NULL; + savedscbptr = ahd_get_scbptr(ahd); + tid_next = ahd_inw(ahd, WAITING_TID_HEAD); + tid_prev = SCB_LIST_NULL; + targets = 0; + for (scbid = tid_next; !SCBID_IS_NULL(scbid); scbid = tid_next) { + u_int tid_head; + u_int tid_tail; + + targets++; + if (targets > AHD_NUM_TARGETS) + panic("TID LIST LOOP"); + + if (scbid >= ahd->scb_data.numscbs) { + printk("%s: Waiting TID List inconsistency. " + "SCB index == 0x%x, yet numscbs == 0x%x.", + ahd_name(ahd), scbid, ahd->scb_data.numscbs); + ahd_dump_card_state(ahd); + panic("for safety"); + } + scb = ahd_lookup_scb(ahd, scbid); + if (scb == NULL) { + printk("%s: SCB = 0x%x Not Active!\n", + ahd_name(ahd), scbid); + panic("Waiting TID List traversal\n"); + } + ahd_set_scbptr(ahd, scbid); + tid_next = ahd_inw_scbram(ahd, SCB_NEXT2); + if (ahd_match_scb(ahd, scb, target, channel, CAM_LUN_WILDCARD, + SCB_LIST_NULL, ROLE_UNKNOWN) == 0) { + tid_prev = scbid; + continue; + } + + /* + * We found a list of scbs that needs to be searched. + */ + if (action == SEARCH_PRINT) + printk(" %d ( ", SCB_GET_TARGET(ahd, scb)); + tid_head = scbid; + found += ahd_search_scb_list(ahd, target, channel, + lun, tag, role, status, + action, &tid_head, &tid_tail, + SCB_GET_TARGET(ahd, scb)); + /* + * Check any MK_MESSAGE SCB that is still waiting to + * enter this target's waiting for selection queue. + */ + if (mk_msg_scb != NULL + && ahd_match_scb(ahd, mk_msg_scb, target, channel, + lun, tag, role)) { + + /* + * We found an scb that needs to be acted on. + */ + found++; + switch (action) { + case SEARCH_COMPLETE: + if ((mk_msg_scb->flags & SCB_ACTIVE) == 0) + printk("Inactive SCB pending MK_MSG\n"); + ahd_done_with_status(ahd, mk_msg_scb, status); + fallthrough; + case SEARCH_REMOVE: + { + u_int tail_offset; + + printk("Removing MK_MSG scb\n"); + + /* + * Reset our tail to the tail of the + * main per-target list. + */ + tail_offset = WAITING_SCB_TAILS + + (2 * SCB_GET_TARGET(ahd, mk_msg_scb)); + ahd_outw(ahd, tail_offset, tid_tail); + + seq_flags2 &= ~PENDING_MK_MESSAGE; + ahd_outb(ahd, SEQ_FLAGS2, seq_flags2); + ahd_outw(ahd, CMDS_PENDING, + ahd_inw(ahd, CMDS_PENDING)-1); + mk_msg_scb = NULL; + break; + } + case SEARCH_PRINT: + printk(" 0x%x", SCB_GET_TAG(scb)); + fallthrough; + case SEARCH_COUNT: + break; + } + } + + if (mk_msg_scb != NULL + && SCBID_IS_NULL(tid_head) + && ahd_match_scb(ahd, scb, target, channel, CAM_LUN_WILDCARD, + SCB_LIST_NULL, ROLE_UNKNOWN)) { + + /* + * When removing the last SCB for a target + * queue with a pending MK_MESSAGE scb, we + * must queue the MK_MESSAGE scb. + */ + printk("Queueing mk_msg_scb\n"); + tid_head = ahd_inw(ahd, MK_MESSAGE_SCB); + seq_flags2 &= ~PENDING_MK_MESSAGE; + ahd_outb(ahd, SEQ_FLAGS2, seq_flags2); + mk_msg_scb = NULL; + } + if (tid_head != scbid) + ahd_stitch_tid_list(ahd, tid_prev, tid_head, tid_next); + if (!SCBID_IS_NULL(tid_head)) + tid_prev = tid_head; + if (action == SEARCH_PRINT) + printk(")\n"); + } + + /* Restore saved state. */ + ahd_set_scbptr(ahd, savedscbptr); + ahd_restore_modes(ahd, saved_modes); + return (found); +} + +static int +ahd_search_scb_list(struct ahd_softc *ahd, int target, char channel, + int lun, u_int tag, role_t role, uint32_t status, + ahd_search_action action, u_int *list_head, + u_int *list_tail, u_int tid) +{ + struct scb *scb; + u_int scbid; + u_int next; + u_int prev; + int found; + + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + found = 0; + prev = SCB_LIST_NULL; + next = *list_head; + *list_tail = SCB_LIST_NULL; + for (scbid = next; !SCBID_IS_NULL(scbid); scbid = next) { + if (scbid >= ahd->scb_data.numscbs) { + printk("%s:SCB List inconsistency. " + "SCB == 0x%x, yet numscbs == 0x%x.", + ahd_name(ahd), scbid, ahd->scb_data.numscbs); + ahd_dump_card_state(ahd); + panic("for safety"); + } + scb = ahd_lookup_scb(ahd, scbid); + if (scb == NULL) { + printk("%s: SCB = %d Not Active!\n", + ahd_name(ahd), scbid); + panic("Waiting List traversal\n"); + } + ahd_set_scbptr(ahd, scbid); + *list_tail = scbid; + next = ahd_inw_scbram(ahd, SCB_NEXT); + if (ahd_match_scb(ahd, scb, target, channel, + lun, SCB_LIST_NULL, role) == 0) { + prev = scbid; + continue; + } + found++; + switch (action) { + case SEARCH_COMPLETE: + if ((scb->flags & SCB_ACTIVE) == 0) + printk("Inactive SCB in Waiting List\n"); + ahd_done_with_status(ahd, scb, status); + fallthrough; + case SEARCH_REMOVE: + ahd_rem_wscb(ahd, scbid, prev, next, tid); + *list_tail = prev; + if (SCBID_IS_NULL(prev)) + *list_head = next; + break; + case SEARCH_PRINT: + printk("0x%x ", scbid); + fallthrough; + case SEARCH_COUNT: + prev = scbid; + break; + } + if (found > AHD_SCB_MAX) + panic("SCB LIST LOOP"); + } + if (action == SEARCH_COMPLETE + || action == SEARCH_REMOVE) + ahd_outw(ahd, CMDS_PENDING, ahd_inw(ahd, CMDS_PENDING) - found); + return (found); +} + +static void +ahd_stitch_tid_list(struct ahd_softc *ahd, u_int tid_prev, + u_int tid_cur, u_int tid_next) +{ + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + + if (SCBID_IS_NULL(tid_cur)) { + + /* Bypass current TID list */ + if (SCBID_IS_NULL(tid_prev)) { + ahd_outw(ahd, WAITING_TID_HEAD, tid_next); + } else { + ahd_set_scbptr(ahd, tid_prev); + ahd_outw(ahd, SCB_NEXT2, tid_next); + } + if (SCBID_IS_NULL(tid_next)) + ahd_outw(ahd, WAITING_TID_TAIL, tid_prev); + } else { + + /* Stitch through tid_cur */ + if (SCBID_IS_NULL(tid_prev)) { + ahd_outw(ahd, WAITING_TID_HEAD, tid_cur); + } else { + ahd_set_scbptr(ahd, tid_prev); + ahd_outw(ahd, SCB_NEXT2, tid_cur); + } + ahd_set_scbptr(ahd, tid_cur); + ahd_outw(ahd, SCB_NEXT2, tid_next); + + if (SCBID_IS_NULL(tid_next)) + ahd_outw(ahd, WAITING_TID_TAIL, tid_cur); + } +} + +/* + * Manipulate the waiting for selection list and return the + * scb that follows the one that we remove. + */ +static u_int +ahd_rem_wscb(struct ahd_softc *ahd, u_int scbid, + u_int prev, u_int next, u_int tid) +{ + u_int tail_offset; + + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + if (!SCBID_IS_NULL(prev)) { + ahd_set_scbptr(ahd, prev); + ahd_outw(ahd, SCB_NEXT, next); + } + + /* + * SCBs that have MK_MESSAGE set in them may + * cause the tail pointer to be updated without + * setting the next pointer of the previous tail. + * Only clear the tail if the removed SCB was + * the tail. + */ + tail_offset = WAITING_SCB_TAILS + (2 * tid); + if (SCBID_IS_NULL(next) + && ahd_inw(ahd, tail_offset) == scbid) + ahd_outw(ahd, tail_offset, prev); + + ahd_add_scb_to_free_list(ahd, scbid); + return (next); +} + +/* + * Add the SCB as selected by SCBPTR onto the on chip list of + * free hardware SCBs. This list is empty/unused if we are not + * performing SCB paging. + */ +static void +ahd_add_scb_to_free_list(struct ahd_softc *ahd, u_int scbid) +{ +/* XXX Need some other mechanism to designate "free". */ + /* + * Invalidate the tag so that our abort + * routines don't think it's active. + ahd_outb(ahd, SCB_TAG, SCB_LIST_NULL); + */ +} + +/******************************** Error Handling ******************************/ +/* + * Abort all SCBs that match the given description (target/channel/lun/tag), + * setting their status to the passed in status if the status has not already + * been modified from CAM_REQ_INPROG. This routine assumes that the sequencer + * is paused before it is called. + */ +static int +ahd_abort_scbs(struct ahd_softc *ahd, int target, char channel, + int lun, u_int tag, role_t role, uint32_t status) +{ + struct scb *scbp; + struct scb *scbp_next; + u_int i, j; + u_int maxtarget; + u_int minlun; + u_int maxlun; + int found; + ahd_mode_state saved_modes; + + /* restore this when we're done */ + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + + found = ahd_search_qinfifo(ahd, target, channel, lun, SCB_LIST_NULL, + role, CAM_REQUEUE_REQ, SEARCH_COMPLETE); + + /* + * Clean out the busy target table for any untagged commands. + */ + i = 0; + maxtarget = 16; + if (target != CAM_TARGET_WILDCARD) { + i = target; + if (channel == 'B') + i += 8; + maxtarget = i + 1; + } + + if (lun == CAM_LUN_WILDCARD) { + minlun = 0; + maxlun = AHD_NUM_LUNS_NONPKT; + } else if (lun >= AHD_NUM_LUNS_NONPKT) { + minlun = maxlun = 0; + } else { + minlun = lun; + maxlun = lun + 1; + } + + if (role != ROLE_TARGET) { + for (;i < maxtarget; i++) { + for (j = minlun;j < maxlun; j++) { + u_int scbid; + u_int tcl; + + tcl = BUILD_TCL_RAW(i, 'A', j); + scbid = ahd_find_busy_tcl(ahd, tcl); + scbp = ahd_lookup_scb(ahd, scbid); + if (scbp == NULL + || ahd_match_scb(ahd, scbp, target, channel, + lun, tag, role) == 0) + continue; + ahd_unbusy_tcl(ahd, BUILD_TCL_RAW(i, 'A', j)); + } + } + } + + /* + * Don't abort commands that have already completed, + * but haven't quite made it up to the host yet. + */ + ahd_flush_qoutfifo(ahd); + + /* + * Go through the pending CCB list and look for + * commands for this target that are still active. + * These are other tagged commands that were + * disconnected when the reset occurred. + */ + scbp_next = LIST_FIRST(&ahd->pending_scbs); + while (scbp_next != NULL) { + scbp = scbp_next; + scbp_next = LIST_NEXT(scbp, pending_links); + if (ahd_match_scb(ahd, scbp, target, channel, lun, tag, role)) { + cam_status ostat; + + ostat = ahd_get_transaction_status(scbp); + if (ostat == CAM_REQ_INPROG) + ahd_set_transaction_status(scbp, status); + if (ahd_get_transaction_status(scbp) != CAM_REQ_CMP) + ahd_freeze_scb(scbp); + if ((scbp->flags & SCB_ACTIVE) == 0) + printk("Inactive SCB on pending list\n"); + ahd_done(ahd, scbp); + found++; + } + } + ahd_restore_modes(ahd, saved_modes); + ahd_platform_abort_scbs(ahd, target, channel, lun, tag, role, status); + ahd->flags |= AHD_UPDATE_PEND_CMDS; + return found; +} + +static void +ahd_reset_current_bus(struct ahd_softc *ahd) +{ + uint8_t scsiseq; + + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + ahd_outb(ahd, SIMODE1, ahd_inb(ahd, SIMODE1) & ~ENSCSIRST); + scsiseq = ahd_inb(ahd, SCSISEQ0) & ~(ENSELO|ENARBO|SCSIRSTO); + ahd_outb(ahd, SCSISEQ0, scsiseq | SCSIRSTO); + ahd_flush_device_writes(ahd); + ahd_delay(AHD_BUSRESET_DELAY); + /* Turn off the bus reset */ + ahd_outb(ahd, SCSISEQ0, scsiseq); + ahd_flush_device_writes(ahd); + ahd_delay(AHD_BUSRESET_DELAY); + if ((ahd->bugs & AHD_SCSIRST_BUG) != 0) { + /* + * 2A Razor #474 + * Certain chip state is not cleared for + * SCSI bus resets that we initiate, so + * we must reset the chip. + */ + ahd_reset(ahd, /*reinit*/TRUE); + ahd_intr_enable(ahd, /*enable*/TRUE); + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + } + + ahd_clear_intstat(ahd); +} + +int +ahd_reset_channel(struct ahd_softc *ahd, char channel, int initiate_reset) +{ + struct ahd_devinfo caminfo; + u_int initiator; + u_int target; + u_int max_scsiid; + int found; + u_int fifo; + u_int next_fifo; + uint8_t scsiseq; + + /* + * Check if the last bus reset is cleared + */ + if (ahd->flags & AHD_BUS_RESET_ACTIVE) { + printk("%s: bus reset still active\n", + ahd_name(ahd)); + return 0; + } + ahd->flags |= AHD_BUS_RESET_ACTIVE; + + ahd->pending_device = NULL; + + ahd_compile_devinfo(&caminfo, + CAM_TARGET_WILDCARD, + CAM_TARGET_WILDCARD, + CAM_LUN_WILDCARD, + channel, ROLE_UNKNOWN); + ahd_pause(ahd); + + /* Make sure the sequencer is in a safe location. */ + ahd_clear_critical_section(ahd); + + /* + * Run our command complete fifos to ensure that we perform + * completion processing on any commands that 'completed' + * before the reset occurred. + */ + ahd_run_qoutfifo(ahd); +#ifdef AHD_TARGET_MODE + if ((ahd->flags & AHD_TARGETROLE) != 0) { + ahd_run_tqinfifo(ahd, /*paused*/TRUE); + } +#endif + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + + /* + * Disable selections so no automatic hardware + * functions will modify chip state. + */ + ahd_outb(ahd, SCSISEQ0, 0); + ahd_outb(ahd, SCSISEQ1, 0); + + /* + * Safely shut down our DMA engines. Always start with + * the FIFO that is not currently active (if any are + * actively connected). + */ + next_fifo = fifo = ahd_inb(ahd, DFFSTAT) & CURRFIFO; + if (next_fifo > CURRFIFO_1) + /* If disconneced, arbitrarily start with FIFO1. */ + next_fifo = fifo = 0; + do { + next_fifo ^= CURRFIFO_1; + ahd_set_modes(ahd, next_fifo, next_fifo); + ahd_outb(ahd, DFCNTRL, + ahd_inb(ahd, DFCNTRL) & ~(SCSIEN|HDMAEN)); + while ((ahd_inb(ahd, DFCNTRL) & HDMAENACK) != 0) + ahd_delay(10); + /* + * Set CURRFIFO to the now inactive channel. + */ + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + ahd_outb(ahd, DFFSTAT, next_fifo); + } while (next_fifo != fifo); + + /* + * Reset the bus if we are initiating this reset + */ + ahd_clear_msg_state(ahd); + ahd_outb(ahd, SIMODE1, + ahd_inb(ahd, SIMODE1) & ~(ENBUSFREE|ENSCSIRST)); + + if (initiate_reset) + ahd_reset_current_bus(ahd); + + ahd_clear_intstat(ahd); + + /* + * Clean up all the state information for the + * pending transactions on this bus. + */ + found = ahd_abort_scbs(ahd, CAM_TARGET_WILDCARD, channel, + CAM_LUN_WILDCARD, SCB_LIST_NULL, + ROLE_UNKNOWN, CAM_SCSI_BUS_RESET); + + /* + * Cleanup anything left in the FIFOs. + */ + ahd_clear_fifo(ahd, 0); + ahd_clear_fifo(ahd, 1); + + /* + * Clear SCSI interrupt status + */ + ahd_outb(ahd, CLRSINT1, CLRSCSIRSTI); + + /* + * Reenable selections + */ + ahd_outb(ahd, SIMODE1, ahd_inb(ahd, SIMODE1) | ENSCSIRST); + scsiseq = ahd_inb(ahd, SCSISEQ_TEMPLATE); + ahd_outb(ahd, SCSISEQ1, scsiseq & (ENSELI|ENRSELI|ENAUTOATNP)); + + max_scsiid = (ahd->features & AHD_WIDE) ? 15 : 7; +#ifdef AHD_TARGET_MODE + /* + * Send an immediate notify ccb to all target more peripheral + * drivers affected by this action. + */ + for (target = 0; target <= max_scsiid; target++) { + struct ahd_tmode_tstate* tstate; + u_int lun; + + tstate = ahd->enabled_targets[target]; + if (tstate == NULL) + continue; + for (lun = 0; lun < AHD_NUM_LUNS; lun++) { + struct ahd_tmode_lstate* lstate; + + lstate = tstate->enabled_luns[lun]; + if (lstate == NULL) + continue; + + ahd_queue_lstate_event(ahd, lstate, CAM_TARGET_WILDCARD, + EVENT_TYPE_BUS_RESET, /*arg*/0); + ahd_send_lstate_events(ahd, lstate); + } + } +#endif + /* + * Revert to async/narrow transfers until we renegotiate. + */ + for (target = 0; target <= max_scsiid; target++) { + + if (ahd->enabled_targets[target] == NULL) + continue; + for (initiator = 0; initiator <= max_scsiid; initiator++) { + struct ahd_devinfo devinfo; + + ahd_compile_devinfo(&devinfo, target, initiator, + CAM_LUN_WILDCARD, + 'A', ROLE_UNKNOWN); + ahd_set_width(ahd, &devinfo, MSG_EXT_WDTR_BUS_8_BIT, + AHD_TRANS_CUR, /*paused*/TRUE); + ahd_set_syncrate(ahd, &devinfo, /*period*/0, + /*offset*/0, /*ppr_options*/0, + AHD_TRANS_CUR, /*paused*/TRUE); + } + } + + /* Notify the XPT that a bus reset occurred */ + ahd_send_async(ahd, caminfo.channel, CAM_TARGET_WILDCARD, + CAM_LUN_WILDCARD, AC_BUS_RESET); + + ahd_restart(ahd); + + return (found); +} + +/**************************** Statistics Processing ***************************/ +static void +ahd_stat_timer(struct timer_list *t) +{ + struct ahd_softc *ahd = from_timer(ahd, t, stat_timer); + u_long s; + int enint_coal; + + ahd_lock(ahd, &s); + + enint_coal = ahd->hs_mailbox & ENINT_COALESCE; + if (ahd->cmdcmplt_total > ahd->int_coalescing_threshold) + enint_coal |= ENINT_COALESCE; + else if (ahd->cmdcmplt_total < ahd->int_coalescing_stop_threshold) + enint_coal &= ~ENINT_COALESCE; + + if (enint_coal != (ahd->hs_mailbox & ENINT_COALESCE)) { + ahd_enable_coalescing(ahd, enint_coal); +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_INT_COALESCING) != 0) + printk("%s: Interrupt coalescing " + "now %sabled. Cmds %d\n", + ahd_name(ahd), + (enint_coal & ENINT_COALESCE) ? "en" : "dis", + ahd->cmdcmplt_total); +#endif + } + + ahd->cmdcmplt_bucket = (ahd->cmdcmplt_bucket+1) & (AHD_STAT_BUCKETS-1); + ahd->cmdcmplt_total -= ahd->cmdcmplt_counts[ahd->cmdcmplt_bucket]; + ahd->cmdcmplt_counts[ahd->cmdcmplt_bucket] = 0; + ahd_timer_reset(&ahd->stat_timer, AHD_STAT_UPDATE_US); + ahd_unlock(ahd, &s); +} + +/****************************** Status Processing *****************************/ + +static void +ahd_handle_scsi_status(struct ahd_softc *ahd, struct scb *scb) +{ + struct hardware_scb *hscb; + int paused; + + /* + * The sequencer freezes its select-out queue + * anytime a SCSI status error occurs. We must + * handle the error and increment our qfreeze count + * to allow the sequencer to continue. We don't + * bother clearing critical sections here since all + * operations are on data structures that the sequencer + * is not touching once the queue is frozen. + */ + hscb = scb->hscb; + + if (ahd_is_paused(ahd)) { + paused = 1; + } else { + paused = 0; + ahd_pause(ahd); + } + + /* Freeze the queue until the client sees the error. */ + ahd_freeze_devq(ahd, scb); + ahd_freeze_scb(scb); + ahd->qfreeze_cnt++; + ahd_outw(ahd, KERNEL_QFREEZE_COUNT, ahd->qfreeze_cnt); + + if (paused == 0) + ahd_unpause(ahd); + + /* Don't want to clobber the original sense code */ + if ((scb->flags & SCB_SENSE) != 0) { + /* + * Clear the SCB_SENSE Flag and perform + * a normal command completion. + */ + scb->flags &= ~SCB_SENSE; + ahd_set_transaction_status(scb, CAM_AUTOSENSE_FAIL); + ahd_done(ahd, scb); + return; + } + ahd_set_transaction_status(scb, CAM_SCSI_STATUS_ERROR); + ahd_set_scsi_status(scb, hscb->shared_data.istatus.scsi_status); + switch (hscb->shared_data.istatus.scsi_status) { + case STATUS_PKT_SENSE: + { + struct scsi_status_iu_header *siu; + + ahd_sync_sense(ahd, scb, BUS_DMASYNC_POSTREAD); + siu = (struct scsi_status_iu_header *)scb->sense_data; + ahd_set_scsi_status(scb, siu->status); +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_SENSE) != 0) { + ahd_print_path(ahd, scb); + printk("SCB 0x%x Received PKT Status of 0x%x\n", + SCB_GET_TAG(scb), siu->status); + printk("\tflags = 0x%x, sense len = 0x%x, " + "pktfail = 0x%x\n", + siu->flags, scsi_4btoul(siu->sense_length), + scsi_4btoul(siu->pkt_failures_length)); + } +#endif + if ((siu->flags & SIU_RSPVALID) != 0) { + ahd_print_path(ahd, scb); + if (scsi_4btoul(siu->pkt_failures_length) < 4) { + printk("Unable to parse pkt_failures\n"); + } else { + + switch (SIU_PKTFAIL_CODE(siu)) { + case SIU_PFC_NONE: + printk("No packet failure found\n"); + break; + case SIU_PFC_CIU_FIELDS_INVALID: + printk("Invalid Command IU Field\n"); + break; + case SIU_PFC_TMF_NOT_SUPPORTED: + printk("TMF not supported\n"); + break; + case SIU_PFC_TMF_FAILED: + printk("TMF failed\n"); + break; + case SIU_PFC_INVALID_TYPE_CODE: + printk("Invalid L_Q Type code\n"); + break; + case SIU_PFC_ILLEGAL_REQUEST: + printk("Illegal request\n"); + default: + break; + } + } + if (siu->status == SCSI_STATUS_OK) + ahd_set_transaction_status(scb, + CAM_REQ_CMP_ERR); + } + if ((siu->flags & SIU_SNSVALID) != 0) { + scb->flags |= SCB_PKT_SENSE; +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_SENSE) != 0) + printk("Sense data available\n"); +#endif + } + ahd_done(ahd, scb); + break; + } + case SCSI_STATUS_CMD_TERMINATED: + case SCSI_STATUS_CHECK_COND: + { + struct ahd_devinfo devinfo; + struct ahd_dma_seg *sg; + struct scsi_sense *sc; + struct ahd_initiator_tinfo *targ_info; + struct ahd_tmode_tstate *tstate; + struct ahd_transinfo *tinfo; +#ifdef AHD_DEBUG + if (ahd_debug & AHD_SHOW_SENSE) { + ahd_print_path(ahd, scb); + printk("SCB %d: requests Check Status\n", + SCB_GET_TAG(scb)); + } +#endif + + if (ahd_perform_autosense(scb) == 0) + break; + + ahd_compile_devinfo(&devinfo, SCB_GET_OUR_ID(scb), + SCB_GET_TARGET(ahd, scb), + SCB_GET_LUN(scb), + SCB_GET_CHANNEL(ahd, scb), + ROLE_INITIATOR); + targ_info = ahd_fetch_transinfo(ahd, + devinfo.channel, + devinfo.our_scsiid, + devinfo.target, + &tstate); + tinfo = &targ_info->curr; + sg = scb->sg_list; + sc = (struct scsi_sense *)hscb->shared_data.idata.cdb; + /* + * Save off the residual if there is one. + */ + ahd_update_residual(ahd, scb); +#ifdef AHD_DEBUG + if (ahd_debug & AHD_SHOW_SENSE) { + ahd_print_path(ahd, scb); + printk("Sending Sense\n"); + } +#endif + scb->sg_count = 0; + sg = ahd_sg_setup(ahd, scb, sg, ahd_get_sense_bufaddr(ahd, scb), + ahd_get_sense_bufsize(ahd, scb), + /*last*/TRUE); + sc->opcode = REQUEST_SENSE; + sc->byte2 = 0; + if (tinfo->protocol_version <= SCSI_REV_2 + && SCB_GET_LUN(scb) < 8) + sc->byte2 = SCB_GET_LUN(scb) << 5; + sc->unused[0] = 0; + sc->unused[1] = 0; + sc->length = ahd_get_sense_bufsize(ahd, scb); + sc->control = 0; + + /* + * We can't allow the target to disconnect. + * This will be an untagged transaction and + * having the target disconnect will make this + * transaction indestinguishable from outstanding + * tagged transactions. + */ + hscb->control = 0; + + /* + * This request sense could be because the + * the device lost power or in some other + * way has lost our transfer negotiations. + * Renegotiate if appropriate. Unit attention + * errors will be reported before any data + * phases occur. + */ + if (ahd_get_residual(scb) == ahd_get_transfer_length(scb)) { + ahd_update_neg_request(ahd, &devinfo, + tstate, targ_info, + AHD_NEG_IF_NON_ASYNC); + } + if (tstate->auto_negotiate & devinfo.target_mask) { + hscb->control |= MK_MESSAGE; + scb->flags &= + ~(SCB_NEGOTIATE|SCB_ABORT|SCB_DEVICE_RESET); + scb->flags |= SCB_AUTO_NEGOTIATE; + } + hscb->cdb_len = sizeof(*sc); + ahd_setup_data_scb(ahd, scb); + scb->flags |= SCB_SENSE; + ahd_queue_scb(ahd, scb); + break; + } + case SCSI_STATUS_OK: + printk("%s: Interrupted for status of 0???\n", + ahd_name(ahd)); + fallthrough; + default: + ahd_done(ahd, scb); + break; + } +} + +static void +ahd_handle_scb_status(struct ahd_softc *ahd, struct scb *scb) +{ + if (scb->hscb->shared_data.istatus.scsi_status != 0) { + ahd_handle_scsi_status(ahd, scb); + } else { + ahd_calc_residual(ahd, scb); + ahd_done(ahd, scb); + } +} + +/* + * Calculate the residual for a just completed SCB. + */ +static void +ahd_calc_residual(struct ahd_softc *ahd, struct scb *scb) +{ + struct hardware_scb *hscb; + struct initiator_status *spkt; + uint32_t sgptr; + uint32_t resid_sgptr; + uint32_t resid; + + /* + * 5 cases. + * 1) No residual. + * SG_STATUS_VALID clear in sgptr. + * 2) Transferless command + * 3) Never performed any transfers. + * sgptr has SG_FULL_RESID set. + * 4) No residual but target did not + * save data pointers after the + * last transfer, so sgptr was + * never updated. + * 5) We have a partial residual. + * Use residual_sgptr to determine + * where we are. + */ + + hscb = scb->hscb; + sgptr = ahd_le32toh(hscb->sgptr); + if ((sgptr & SG_STATUS_VALID) == 0) + /* Case 1 */ + return; + sgptr &= ~SG_STATUS_VALID; + + if ((sgptr & SG_LIST_NULL) != 0) + /* Case 2 */ + return; + + /* + * Residual fields are the same in both + * target and initiator status packets, + * so we can always use the initiator fields + * regardless of the role for this SCB. + */ + spkt = &hscb->shared_data.istatus; + resid_sgptr = ahd_le32toh(spkt->residual_sgptr); + if ((sgptr & SG_FULL_RESID) != 0) { + /* Case 3 */ + resid = ahd_get_transfer_length(scb); + } else if ((resid_sgptr & SG_LIST_NULL) != 0) { + /* Case 4 */ + return; + } else if ((resid_sgptr & SG_OVERRUN_RESID) != 0) { + ahd_print_path(ahd, scb); + printk("data overrun detected Tag == 0x%x.\n", + SCB_GET_TAG(scb)); + ahd_freeze_devq(ahd, scb); + ahd_set_transaction_status(scb, CAM_DATA_RUN_ERR); + ahd_freeze_scb(scb); + return; + } else if ((resid_sgptr & ~SG_PTR_MASK) != 0) { + panic("Bogus resid sgptr value 0x%x\n", resid_sgptr); + /* NOTREACHED */ + } else { + struct ahd_dma_seg *sg; + + /* + * Remainder of the SG where the transfer + * stopped. + */ + resid = ahd_le32toh(spkt->residual_datacnt) & AHD_SG_LEN_MASK; + sg = ahd_sg_bus_to_virt(ahd, scb, resid_sgptr & SG_PTR_MASK); + + /* The residual sg_ptr always points to the next sg */ + sg--; + + /* + * Add up the contents of all residual + * SG segments that are after the SG where + * the transfer stopped. + */ + while ((ahd_le32toh(sg->len) & AHD_DMA_LAST_SEG) == 0) { + sg++; + resid += ahd_le32toh(sg->len) & AHD_SG_LEN_MASK; + } + } + if ((scb->flags & SCB_SENSE) == 0) + ahd_set_residual(scb, resid); + else + ahd_set_sense_residual(scb, resid); + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MISC) != 0) { + ahd_print_path(ahd, scb); + printk("Handled %sResidual of %d bytes\n", + (scb->flags & SCB_SENSE) ? "Sense " : "", resid); + } +#endif +} + +/******************************* Target Mode **********************************/ +#ifdef AHD_TARGET_MODE +/* + * Add a target mode event to this lun's queue + */ +static void +ahd_queue_lstate_event(struct ahd_softc *ahd, struct ahd_tmode_lstate *lstate, + u_int initiator_id, u_int event_type, u_int event_arg) +{ + struct ahd_tmode_event *event; + int pending; + + xpt_freeze_devq(lstate->path, /*count*/1); + if (lstate->event_w_idx >= lstate->event_r_idx) + pending = lstate->event_w_idx - lstate->event_r_idx; + else + pending = AHD_TMODE_EVENT_BUFFER_SIZE + 1 + - (lstate->event_r_idx - lstate->event_w_idx); + + if (event_type == EVENT_TYPE_BUS_RESET + || event_type == MSG_BUS_DEV_RESET) { + /* + * Any earlier events are irrelevant, so reset our buffer. + * This has the effect of allowing us to deal with reset + * floods (an external device holding down the reset line) + * without losing the event that is really interesting. + */ + lstate->event_r_idx = 0; + lstate->event_w_idx = 0; + xpt_release_devq(lstate->path, pending, /*runqueue*/FALSE); + } + + if (pending == AHD_TMODE_EVENT_BUFFER_SIZE) { + xpt_print_path(lstate->path); + printk("immediate event %x:%x lost\n", + lstate->event_buffer[lstate->event_r_idx].event_type, + lstate->event_buffer[lstate->event_r_idx].event_arg); + lstate->event_r_idx++; + if (lstate->event_r_idx == AHD_TMODE_EVENT_BUFFER_SIZE) + lstate->event_r_idx = 0; + xpt_release_devq(lstate->path, /*count*/1, /*runqueue*/FALSE); + } + + event = &lstate->event_buffer[lstate->event_w_idx]; + event->initiator_id = initiator_id; + event->event_type = event_type; + event->event_arg = event_arg; + lstate->event_w_idx++; + if (lstate->event_w_idx == AHD_TMODE_EVENT_BUFFER_SIZE) + lstate->event_w_idx = 0; +} + +/* + * Send any target mode events queued up waiting + * for immediate notify resources. + */ +void +ahd_send_lstate_events(struct ahd_softc *ahd, struct ahd_tmode_lstate *lstate) +{ + struct ccb_hdr *ccbh; + struct ccb_immed_notify *inot; + + while (lstate->event_r_idx != lstate->event_w_idx + && (ccbh = SLIST_FIRST(&lstate->immed_notifies)) != NULL) { + struct ahd_tmode_event *event; + + event = &lstate->event_buffer[lstate->event_r_idx]; + SLIST_REMOVE_HEAD(&lstate->immed_notifies, sim_links.sle); + inot = (struct ccb_immed_notify *)ccbh; + switch (event->event_type) { + case EVENT_TYPE_BUS_RESET: + ccbh->status = CAM_SCSI_BUS_RESET|CAM_DEV_QFRZN; + break; + default: + ccbh->status = CAM_MESSAGE_RECV|CAM_DEV_QFRZN; + inot->message_args[0] = event->event_type; + inot->message_args[1] = event->event_arg; + break; + } + inot->initiator_id = event->initiator_id; + inot->sense_len = 0; + xpt_done((union ccb *)inot); + lstate->event_r_idx++; + if (lstate->event_r_idx == AHD_TMODE_EVENT_BUFFER_SIZE) + lstate->event_r_idx = 0; + } +} +#endif + +/******************** Sequencer Program Patching/Download *********************/ + +#ifdef AHD_DUMP_SEQ +void +ahd_dumpseq(struct ahd_softc* ahd) +{ + int i; + int max_prog; + + max_prog = 2048; + + ahd_outb(ahd, SEQCTL0, PERRORDIS|FAILDIS|FASTMODE|LOADRAM); + ahd_outw(ahd, PRGMCNT, 0); + for (i = 0; i < max_prog; i++) { + uint8_t ins_bytes[4]; + + ahd_insb(ahd, SEQRAM, ins_bytes, 4); + printk("0x%08x\n", ins_bytes[0] << 24 + | ins_bytes[1] << 16 + | ins_bytes[2] << 8 + | ins_bytes[3]); + } +} +#endif + +static void +ahd_loadseq(struct ahd_softc *ahd) +{ + struct cs cs_table[NUM_CRITICAL_SECTIONS]; + u_int begin_set[NUM_CRITICAL_SECTIONS]; + u_int end_set[NUM_CRITICAL_SECTIONS]; + const struct patch *cur_patch; + u_int cs_count; + u_int cur_cs; + u_int i; + int downloaded; + u_int skip_addr; + u_int sg_prefetch_cnt; + u_int sg_prefetch_cnt_limit; + u_int sg_prefetch_align; + u_int sg_size; + u_int cacheline_mask; + uint8_t download_consts[DOWNLOAD_CONST_COUNT]; + + if (bootverbose) + printk("%s: Downloading Sequencer Program...", + ahd_name(ahd)); + +#if DOWNLOAD_CONST_COUNT != 8 +#error "Download Const Mismatch" +#endif + /* + * Start out with 0 critical sections + * that apply to this firmware load. + */ + cs_count = 0; + cur_cs = 0; + memset(begin_set, 0, sizeof(begin_set)); + memset(end_set, 0, sizeof(end_set)); + + /* + * Setup downloadable constant table. + * + * The computation for the S/G prefetch variables is + * a bit complicated. We would like to always fetch + * in terms of cachelined sized increments. However, + * if the cacheline is not an even multiple of the + * SG element size or is larger than our SG RAM, using + * just the cache size might leave us with only a portion + * of an SG element at the tail of a prefetch. If the + * cacheline is larger than our S/G prefetch buffer less + * the size of an SG element, we may round down to a cacheline + * that doesn't contain any or all of the S/G of interest + * within the bounds of our S/G ram. Provide variables to + * the sequencer that will allow it to handle these edge + * cases. + */ + /* Start by aligning to the nearest cacheline. */ + sg_prefetch_align = ahd->pci_cachesize; + if (sg_prefetch_align == 0) + sg_prefetch_align = 8; + /* Round down to the nearest power of 2. */ + while (powerof2(sg_prefetch_align) == 0) + sg_prefetch_align--; + + cacheline_mask = sg_prefetch_align - 1; + + /* + * If the cacheline boundary is greater than half our prefetch RAM + * we risk not being able to fetch even a single complete S/G + * segment if we align to that boundary. + */ + if (sg_prefetch_align > CCSGADDR_MAX/2) + sg_prefetch_align = CCSGADDR_MAX/2; + /* Start by fetching a single cacheline. */ + sg_prefetch_cnt = sg_prefetch_align; + /* + * Increment the prefetch count by cachelines until + * at least one S/G element will fit. + */ + sg_size = sizeof(struct ahd_dma_seg); + if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) + sg_size = sizeof(struct ahd_dma64_seg); + while (sg_prefetch_cnt < sg_size) + sg_prefetch_cnt += sg_prefetch_align; + /* + * If the cacheline is not an even multiple of + * the S/G size, we may only get a partial S/G when + * we align. Add a cacheline if this is the case. + */ + if ((sg_prefetch_align % sg_size) != 0 + && (sg_prefetch_cnt < CCSGADDR_MAX)) + sg_prefetch_cnt += sg_prefetch_align; + /* + * Lastly, compute a value that the sequencer can use + * to determine if the remainder of the CCSGRAM buffer + * has a full S/G element in it. + */ + sg_prefetch_cnt_limit = -(sg_prefetch_cnt - sg_size + 1); + download_consts[SG_PREFETCH_CNT] = sg_prefetch_cnt; + download_consts[SG_PREFETCH_CNT_LIMIT] = sg_prefetch_cnt_limit; + download_consts[SG_PREFETCH_ALIGN_MASK] = ~(sg_prefetch_align - 1); + download_consts[SG_PREFETCH_ADDR_MASK] = (sg_prefetch_align - 1); + download_consts[SG_SIZEOF] = sg_size; + download_consts[PKT_OVERRUN_BUFOFFSET] = + (ahd->overrun_buf - (uint8_t *)ahd->qoutfifo) / 256; + download_consts[SCB_TRANSFER_SIZE] = SCB_TRANSFER_SIZE_1BYTE_LUN; + download_consts[CACHELINE_MASK] = cacheline_mask; + cur_patch = patches; + downloaded = 0; + skip_addr = 0; + ahd_outb(ahd, SEQCTL0, PERRORDIS|FAILDIS|FASTMODE|LOADRAM); + ahd_outw(ahd, PRGMCNT, 0); + + for (i = 0; i < sizeof(seqprog)/4; i++) { + if (ahd_check_patch(ahd, &cur_patch, i, &skip_addr) == 0) { + /* + * Don't download this instruction as it + * is in a patch that was removed. + */ + continue; + } + /* + * Move through the CS table until we find a CS + * that might apply to this instruction. + */ + for (; cur_cs < NUM_CRITICAL_SECTIONS; cur_cs++) { + if (critical_sections[cur_cs].end <= i) { + if (begin_set[cs_count] == TRUE + && end_set[cs_count] == FALSE) { + cs_table[cs_count].end = downloaded; + end_set[cs_count] = TRUE; + cs_count++; + } + continue; + } + if (critical_sections[cur_cs].begin <= i + && begin_set[cs_count] == FALSE) { + cs_table[cs_count].begin = downloaded; + begin_set[cs_count] = TRUE; + } + break; + } + ahd_download_instr(ahd, i, download_consts); + downloaded++; + } + + ahd->num_critical_sections = cs_count; + if (cs_count != 0) { + + cs_count *= sizeof(struct cs); + ahd->critical_sections = kmemdup(cs_table, cs_count, GFP_ATOMIC); + if (ahd->critical_sections == NULL) + panic("ahd_loadseq: Could not malloc"); + } + ahd_outb(ahd, SEQCTL0, PERRORDIS|FAILDIS|FASTMODE); + + if (bootverbose) { + printk(" %d instructions downloaded\n", downloaded); + printk("%s: Features 0x%x, Bugs 0x%x, Flags 0x%x\n", + ahd_name(ahd), ahd->features, ahd->bugs, ahd->flags); + } +} + +static int +ahd_check_patch(struct ahd_softc *ahd, const struct patch **start_patch, + u_int start_instr, u_int *skip_addr) +{ + const struct patch *cur_patch; + const struct patch *last_patch; + u_int num_patches; + + num_patches = ARRAY_SIZE(patches); + last_patch = &patches[num_patches]; + cur_patch = *start_patch; + + while (cur_patch < last_patch && start_instr == cur_patch->begin) { + + if (cur_patch->patch_func(ahd) == 0) { + + /* Start rejecting code */ + *skip_addr = start_instr + cur_patch->skip_instr; + cur_patch += cur_patch->skip_patch; + } else { + /* Accepted this patch. Advance to the next + * one and wait for our intruction pointer to + * hit this point. + */ + cur_patch++; + } + } + + *start_patch = cur_patch; + if (start_instr < *skip_addr) + /* Still skipping */ + return (0); + + return (1); +} + +static u_int +ahd_resolve_seqaddr(struct ahd_softc *ahd, u_int address) +{ + const struct patch *cur_patch; + int address_offset; + u_int skip_addr; + u_int i; + + address_offset = 0; + cur_patch = patches; + skip_addr = 0; + + for (i = 0; i < address;) { + + ahd_check_patch(ahd, &cur_patch, i, &skip_addr); + + if (skip_addr > i) { + int end_addr; + + end_addr = min(address, skip_addr); + address_offset += end_addr - i; + i = skip_addr; + } else { + i++; + } + } + return (address - address_offset); +} + +static void +ahd_download_instr(struct ahd_softc *ahd, u_int instrptr, uint8_t *dconsts) +{ + union ins_formats instr; + struct ins_format1 *fmt1_ins; + struct ins_format3 *fmt3_ins; + u_int opcode; + + /* + * The firmware is always compiled into a little endian format. + */ + instr.integer = ahd_le32toh(*(uint32_t*)&seqprog[instrptr * 4]); + + fmt1_ins = &instr.format1; + fmt3_ins = NULL; + + /* Pull the opcode */ + opcode = instr.format1.opcode; + switch (opcode) { + case AIC_OP_JMP: + case AIC_OP_JC: + case AIC_OP_JNC: + case AIC_OP_CALL: + case AIC_OP_JNE: + case AIC_OP_JNZ: + case AIC_OP_JE: + case AIC_OP_JZ: + { + fmt3_ins = &instr.format3; + fmt3_ins->address = ahd_resolve_seqaddr(ahd, fmt3_ins->address); + } + fallthrough; + case AIC_OP_OR: + case AIC_OP_AND: + case AIC_OP_XOR: + case AIC_OP_ADD: + case AIC_OP_ADC: + case AIC_OP_BMOV: + if (fmt1_ins->parity != 0) { + fmt1_ins->immediate = dconsts[fmt1_ins->immediate]; + } + fmt1_ins->parity = 0; + fallthrough; + case AIC_OP_ROL: + { + int i, count; + + /* Calculate odd parity for the instruction */ + for (i = 0, count = 0; i < 31; i++) { + uint32_t mask; + + mask = 0x01 << i; + if ((instr.integer & mask) != 0) + count++; + } + if ((count & 0x01) == 0) + instr.format1.parity = 1; + + /* The sequencer is a little endian cpu */ + instr.integer = ahd_htole32(instr.integer); + ahd_outsb(ahd, SEQRAM, instr.bytes, 4); + break; + } + default: + panic("Unknown opcode encountered in seq program"); + break; + } +} + +static int +ahd_probe_stack_size(struct ahd_softc *ahd) +{ + int last_probe; + + last_probe = 0; + while (1) { + int i; + + /* + * We avoid using 0 as a pattern to avoid + * confusion if the stack implementation + * "back-fills" with zeros when "poping' + * entries. + */ + for (i = 1; i <= last_probe+1; i++) { + ahd_outb(ahd, STACK, i & 0xFF); + ahd_outb(ahd, STACK, (i >> 8) & 0xFF); + } + + /* Verify */ + for (i = last_probe+1; i > 0; i--) { + u_int stack_entry; + + stack_entry = ahd_inb(ahd, STACK) + |(ahd_inb(ahd, STACK) << 8); + if (stack_entry != i) + goto sized; + } + last_probe++; + } +sized: + return (last_probe); +} + +int +ahd_print_register(const ahd_reg_parse_entry_t *table, u_int num_entries, + const char *name, u_int address, u_int value, + u_int *cur_column, u_int wrap_point) +{ + int printed; + u_int printed_mask; + + if (cur_column != NULL && *cur_column >= wrap_point) { + printk("\n"); + *cur_column = 0; + } + printed = printk("%s[0x%x]", name, value); + if (table == NULL) { + printed += printk(" "); + *cur_column += printed; + return (printed); + } + printed_mask = 0; + while (printed_mask != 0xFF) { + int entry; + + for (entry = 0; entry < num_entries; entry++) { + if (((value & table[entry].mask) + != table[entry].value) + || ((printed_mask & table[entry].mask) + == table[entry].mask)) + continue; + + printed += printk("%s%s", + printed_mask == 0 ? ":(" : "|", + table[entry].name); + printed_mask |= table[entry].mask; + + break; + } + if (entry >= num_entries) + break; + } + if (printed_mask != 0) + printed += printk(") "); + else + printed += printk(" "); + if (cur_column != NULL) + *cur_column += printed; + return (printed); +} + +void +ahd_dump_card_state(struct ahd_softc *ahd) +{ + struct scb *scb; + ahd_mode_state saved_modes; + u_int dffstat; + int paused; + u_int scb_index; + u_int saved_scb_index; + u_int cur_col; + int i; + + if (ahd_is_paused(ahd)) { + paused = 1; + } else { + paused = 0; + ahd_pause(ahd); + } + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + printk(">>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<\n" + "%s: Dumping Card State at program address 0x%x Mode 0x%x\n", + ahd_name(ahd), + ahd_inw(ahd, CURADDR), + ahd_build_mode_state(ahd, ahd->saved_src_mode, + ahd->saved_dst_mode)); + if (paused) + printk("Card was paused\n"); + + if (ahd_check_cmdcmpltqueues(ahd)) + printk("Completions are pending\n"); + + /* + * Mode independent registers. + */ + cur_col = 0; + ahd_intstat_print(ahd_inb(ahd, INTSTAT), &cur_col, 50); + ahd_seloid_print(ahd_inb(ahd, SELOID), &cur_col, 50); + ahd_selid_print(ahd_inb(ahd, SELID), &cur_col, 50); + ahd_hs_mailbox_print(ahd_inb(ahd, LOCAL_HS_MAILBOX), &cur_col, 50); + ahd_intctl_print(ahd_inb(ahd, INTCTL), &cur_col, 50); + ahd_seqintstat_print(ahd_inb(ahd, SEQINTSTAT), &cur_col, 50); + ahd_saved_mode_print(ahd_inb(ahd, SAVED_MODE), &cur_col, 50); + ahd_dffstat_print(ahd_inb(ahd, DFFSTAT), &cur_col, 50); + ahd_scsisigi_print(ahd_inb(ahd, SCSISIGI), &cur_col, 50); + ahd_scsiphase_print(ahd_inb(ahd, SCSIPHASE), &cur_col, 50); + ahd_scsibus_print(ahd_inb(ahd, SCSIBUS), &cur_col, 50); + ahd_lastphase_print(ahd_inb(ahd, LASTPHASE), &cur_col, 50); + ahd_scsiseq0_print(ahd_inb(ahd, SCSISEQ0), &cur_col, 50); + ahd_scsiseq1_print(ahd_inb(ahd, SCSISEQ1), &cur_col, 50); + ahd_seqctl0_print(ahd_inb(ahd, SEQCTL0), &cur_col, 50); + ahd_seqintctl_print(ahd_inb(ahd, SEQINTCTL), &cur_col, 50); + ahd_seq_flags_print(ahd_inb(ahd, SEQ_FLAGS), &cur_col, 50); + ahd_seq_flags2_print(ahd_inb(ahd, SEQ_FLAGS2), &cur_col, 50); + ahd_qfreeze_count_print(ahd_inw(ahd, QFREEZE_COUNT), &cur_col, 50); + ahd_kernel_qfreeze_count_print(ahd_inw(ahd, KERNEL_QFREEZE_COUNT), + &cur_col, 50); + ahd_mk_message_scb_print(ahd_inw(ahd, MK_MESSAGE_SCB), &cur_col, 50); + ahd_mk_message_scsiid_print(ahd_inb(ahd, MK_MESSAGE_SCSIID), + &cur_col, 50); + ahd_sstat0_print(ahd_inb(ahd, SSTAT0), &cur_col, 50); + ahd_sstat1_print(ahd_inb(ahd, SSTAT1), &cur_col, 50); + ahd_sstat2_print(ahd_inb(ahd, SSTAT2), &cur_col, 50); + ahd_sstat3_print(ahd_inb(ahd, SSTAT3), &cur_col, 50); + ahd_perrdiag_print(ahd_inb(ahd, PERRDIAG), &cur_col, 50); + ahd_simode1_print(ahd_inb(ahd, SIMODE1), &cur_col, 50); + ahd_lqistat0_print(ahd_inb(ahd, LQISTAT0), &cur_col, 50); + ahd_lqistat1_print(ahd_inb(ahd, LQISTAT1), &cur_col, 50); + ahd_lqistat2_print(ahd_inb(ahd, LQISTAT2), &cur_col, 50); + ahd_lqostat0_print(ahd_inb(ahd, LQOSTAT0), &cur_col, 50); + ahd_lqostat1_print(ahd_inb(ahd, LQOSTAT1), &cur_col, 50); + ahd_lqostat2_print(ahd_inb(ahd, LQOSTAT2), &cur_col, 50); + printk("\n"); + printk("\nSCB Count = %d CMDS_PENDING = %d LASTSCB 0x%x " + "CURRSCB 0x%x NEXTSCB 0x%x\n", + ahd->scb_data.numscbs, ahd_inw(ahd, CMDS_PENDING), + ahd_inw(ahd, LASTSCB), ahd_inw(ahd, CURRSCB), + ahd_inw(ahd, NEXTSCB)); + cur_col = 0; + /* QINFIFO */ + ahd_search_qinfifo(ahd, CAM_TARGET_WILDCARD, ALL_CHANNELS, + CAM_LUN_WILDCARD, SCB_LIST_NULL, + ROLE_UNKNOWN, /*status*/0, SEARCH_PRINT); + saved_scb_index = ahd_get_scbptr(ahd); + printk("Pending list:"); + i = 0; + LIST_FOREACH(scb, &ahd->pending_scbs, pending_links) { + if (i++ > AHD_SCB_MAX) + break; + cur_col = printk("\n%3d FIFO_USE[0x%x] ", SCB_GET_TAG(scb), + ahd_inb_scbram(ahd, SCB_FIFO_USE_COUNT)); + ahd_set_scbptr(ahd, SCB_GET_TAG(scb)); + ahd_scb_control_print(ahd_inb_scbram(ahd, SCB_CONTROL), + &cur_col, 60); + ahd_scb_scsiid_print(ahd_inb_scbram(ahd, SCB_SCSIID), + &cur_col, 60); + } + printk("\nTotal %d\n", i); + + printk("Kernel Free SCB list: "); + i = 0; + TAILQ_FOREACH(scb, &ahd->scb_data.free_scbs, links.tqe) { + struct scb *list_scb; + + list_scb = scb; + do { + printk("%d ", SCB_GET_TAG(list_scb)); + list_scb = LIST_NEXT(list_scb, collision_links); + } while (list_scb && i++ < AHD_SCB_MAX); + } + + LIST_FOREACH(scb, &ahd->scb_data.any_dev_free_scb_list, links.le) { + if (i++ > AHD_SCB_MAX) + break; + printk("%d ", SCB_GET_TAG(scb)); + } + printk("\n"); + + printk("Sequencer Complete DMA-inprog list: "); + scb_index = ahd_inw(ahd, COMPLETE_SCB_DMAINPROG_HEAD); + i = 0; + while (!SCBID_IS_NULL(scb_index) && i++ < AHD_SCB_MAX) { + ahd_set_scbptr(ahd, scb_index); + printk("%d ", scb_index); + scb_index = ahd_inw_scbram(ahd, SCB_NEXT_COMPLETE); + } + printk("\n"); + + printk("Sequencer Complete list: "); + scb_index = ahd_inw(ahd, COMPLETE_SCB_HEAD); + i = 0; + while (!SCBID_IS_NULL(scb_index) && i++ < AHD_SCB_MAX) { + ahd_set_scbptr(ahd, scb_index); + printk("%d ", scb_index); + scb_index = ahd_inw_scbram(ahd, SCB_NEXT_COMPLETE); + } + printk("\n"); + + + printk("Sequencer DMA-Up and Complete list: "); + scb_index = ahd_inw(ahd, COMPLETE_DMA_SCB_HEAD); + i = 0; + while (!SCBID_IS_NULL(scb_index) && i++ < AHD_SCB_MAX) { + ahd_set_scbptr(ahd, scb_index); + printk("%d ", scb_index); + scb_index = ahd_inw_scbram(ahd, SCB_NEXT_COMPLETE); + } + printk("\n"); + printk("Sequencer On QFreeze and Complete list: "); + scb_index = ahd_inw(ahd, COMPLETE_ON_QFREEZE_HEAD); + i = 0; + while (!SCBID_IS_NULL(scb_index) && i++ < AHD_SCB_MAX) { + ahd_set_scbptr(ahd, scb_index); + printk("%d ", scb_index); + scb_index = ahd_inw_scbram(ahd, SCB_NEXT_COMPLETE); + } + printk("\n"); + ahd_set_scbptr(ahd, saved_scb_index); + dffstat = ahd_inb(ahd, DFFSTAT); + for (i = 0; i < 2; i++) { +#ifdef AHD_DEBUG + struct scb *fifo_scb; +#endif + u_int fifo_scbptr; + + ahd_set_modes(ahd, AHD_MODE_DFF0 + i, AHD_MODE_DFF0 + i); + fifo_scbptr = ahd_get_scbptr(ahd); + printk("\n\n%s: FIFO%d %s, LONGJMP == 0x%x, SCB 0x%x\n", + ahd_name(ahd), i, + (dffstat & (FIFO0FREE << i)) ? "Free" : "Active", + ahd_inw(ahd, LONGJMP_ADDR), fifo_scbptr); + cur_col = 0; + ahd_seqimode_print(ahd_inb(ahd, SEQIMODE), &cur_col, 50); + ahd_seqintsrc_print(ahd_inb(ahd, SEQINTSRC), &cur_col, 50); + ahd_dfcntrl_print(ahd_inb(ahd, DFCNTRL), &cur_col, 50); + ahd_dfstatus_print(ahd_inb(ahd, DFSTATUS), &cur_col, 50); + ahd_sg_cache_shadow_print(ahd_inb(ahd, SG_CACHE_SHADOW), + &cur_col, 50); + ahd_sg_state_print(ahd_inb(ahd, SG_STATE), &cur_col, 50); + ahd_dffsxfrctl_print(ahd_inb(ahd, DFFSXFRCTL), &cur_col, 50); + ahd_soffcnt_print(ahd_inb(ahd, SOFFCNT), &cur_col, 50); + ahd_mdffstat_print(ahd_inb(ahd, MDFFSTAT), &cur_col, 50); + if (cur_col > 50) { + printk("\n"); + cur_col = 0; + } + cur_col += printk("SHADDR = 0x%x%x, SHCNT = 0x%x ", + ahd_inl(ahd, SHADDR+4), + ahd_inl(ahd, SHADDR), + (ahd_inb(ahd, SHCNT) + | (ahd_inb(ahd, SHCNT + 1) << 8) + | (ahd_inb(ahd, SHCNT + 2) << 16))); + if (cur_col > 50) { + printk("\n"); + cur_col = 0; + } + cur_col += printk("HADDR = 0x%x%x, HCNT = 0x%x ", + ahd_inl(ahd, HADDR+4), + ahd_inl(ahd, HADDR), + (ahd_inb(ahd, HCNT) + | (ahd_inb(ahd, HCNT + 1) << 8) + | (ahd_inb(ahd, HCNT + 2) << 16))); + ahd_ccsgctl_print(ahd_inb(ahd, CCSGCTL), &cur_col, 50); +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_SG) != 0) { + fifo_scb = ahd_lookup_scb(ahd, fifo_scbptr); + if (fifo_scb != NULL) + ahd_dump_sglist(fifo_scb); + } +#endif + } + printk("\nLQIN: "); + for (i = 0; i < 20; i++) + printk("0x%x ", ahd_inb(ahd, LQIN + i)); + printk("\n"); + ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); + printk("%s: LQISTATE = 0x%x, LQOSTATE = 0x%x, OPTIONMODE = 0x%x\n", + ahd_name(ahd), ahd_inb(ahd, LQISTATE), ahd_inb(ahd, LQOSTATE), + ahd_inb(ahd, OPTIONMODE)); + printk("%s: OS_SPACE_CNT = 0x%x MAXCMDCNT = 0x%x\n", + ahd_name(ahd), ahd_inb(ahd, OS_SPACE_CNT), + ahd_inb(ahd, MAXCMDCNT)); + printk("%s: SAVED_SCSIID = 0x%x SAVED_LUN = 0x%x\n", + ahd_name(ahd), ahd_inb(ahd, SAVED_SCSIID), + ahd_inb(ahd, SAVED_LUN)); + ahd_simode0_print(ahd_inb(ahd, SIMODE0), &cur_col, 50); + printk("\n"); + ahd_set_modes(ahd, AHD_MODE_CCHAN, AHD_MODE_CCHAN); + cur_col = 0; + ahd_ccscbctl_print(ahd_inb(ahd, CCSCBCTL), &cur_col, 50); + printk("\n"); + ahd_set_modes(ahd, ahd->saved_src_mode, ahd->saved_dst_mode); + printk("%s: REG0 == 0x%x, SINDEX = 0x%x, DINDEX = 0x%x\n", + ahd_name(ahd), ahd_inw(ahd, REG0), ahd_inw(ahd, SINDEX), + ahd_inw(ahd, DINDEX)); + printk("%s: SCBPTR == 0x%x, SCB_NEXT == 0x%x, SCB_NEXT2 == 0x%x\n", + ahd_name(ahd), ahd_get_scbptr(ahd), + ahd_inw_scbram(ahd, SCB_NEXT), + ahd_inw_scbram(ahd, SCB_NEXT2)); + printk("CDB %x %x %x %x %x %x\n", + ahd_inb_scbram(ahd, SCB_CDB_STORE), + ahd_inb_scbram(ahd, SCB_CDB_STORE+1), + ahd_inb_scbram(ahd, SCB_CDB_STORE+2), + ahd_inb_scbram(ahd, SCB_CDB_STORE+3), + ahd_inb_scbram(ahd, SCB_CDB_STORE+4), + ahd_inb_scbram(ahd, SCB_CDB_STORE+5)); + printk("STACK:"); + for (i = 0; i < ahd->stack_size; i++) { + ahd->saved_stack[i] = + ahd_inb(ahd, STACK)|(ahd_inb(ahd, STACK) << 8); + printk(" 0x%x", ahd->saved_stack[i]); + } + for (i = ahd->stack_size-1; i >= 0; i--) { + ahd_outb(ahd, STACK, ahd->saved_stack[i] & 0xFF); + ahd_outb(ahd, STACK, (ahd->saved_stack[i] >> 8) & 0xFF); + } + printk("\n<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>\n"); + ahd_restore_modes(ahd, saved_modes); + if (paused == 0) + ahd_unpause(ahd); +} + +#if 0 +void +ahd_dump_scbs(struct ahd_softc *ahd) +{ + ahd_mode_state saved_modes; + u_int saved_scb_index; + int i; + + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + saved_scb_index = ahd_get_scbptr(ahd); + for (i = 0; i < AHD_SCB_MAX; i++) { + ahd_set_scbptr(ahd, i); + printk("%3d", i); + printk("(CTRL 0x%x ID 0x%x N 0x%x N2 0x%x SG 0x%x, RSG 0x%x)\n", + ahd_inb_scbram(ahd, SCB_CONTROL), + ahd_inb_scbram(ahd, SCB_SCSIID), + ahd_inw_scbram(ahd, SCB_NEXT), + ahd_inw_scbram(ahd, SCB_NEXT2), + ahd_inl_scbram(ahd, SCB_SGPTR), + ahd_inl_scbram(ahd, SCB_RESIDUAL_SGPTR)); + } + printk("\n"); + ahd_set_scbptr(ahd, saved_scb_index); + ahd_restore_modes(ahd, saved_modes); +} +#endif /* 0 */ + +/**************************** Flexport Logic **********************************/ +/* + * Read count 16bit words from 16bit word address start_addr from the + * SEEPROM attached to the controller, into buf, using the controller's + * SEEPROM reading state machine. Optionally treat the data as a byte + * stream in terms of byte order. + */ +int +ahd_read_seeprom(struct ahd_softc *ahd, uint16_t *buf, + u_int start_addr, u_int count, int bytestream) +{ + u_int cur_addr; + u_int end_addr; + int error; + + /* + * If we never make it through the loop even once, + * we were passed invalid arguments. + */ + error = EINVAL; + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + end_addr = start_addr + count; + for (cur_addr = start_addr; cur_addr < end_addr; cur_addr++) { + + ahd_outb(ahd, SEEADR, cur_addr); + ahd_outb(ahd, SEECTL, SEEOP_READ | SEESTART); + + error = ahd_wait_seeprom(ahd); + if (error) + break; + if (bytestream != 0) { + uint8_t *bytestream_ptr; + + bytestream_ptr = (uint8_t *)buf; + *bytestream_ptr++ = ahd_inb(ahd, SEEDAT); + *bytestream_ptr = ahd_inb(ahd, SEEDAT+1); + } else { + /* + * ahd_inw() already handles machine byte order. + */ + *buf = ahd_inw(ahd, SEEDAT); + } + buf++; + } + return (error); +} + +/* + * Write count 16bit words from buf, into SEEPROM attache to the + * controller starting at 16bit word address start_addr, using the + * controller's SEEPROM writing state machine. + */ +int +ahd_write_seeprom(struct ahd_softc *ahd, uint16_t *buf, + u_int start_addr, u_int count) +{ + u_int cur_addr; + u_int end_addr; + int error; + int retval; + + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + error = ENOENT; + + /* Place the chip into write-enable mode */ + ahd_outb(ahd, SEEADR, SEEOP_EWEN_ADDR); + ahd_outb(ahd, SEECTL, SEEOP_EWEN | SEESTART); + error = ahd_wait_seeprom(ahd); + if (error) + return (error); + + /* + * Write the data. If we don't get through the loop at + * least once, the arguments were invalid. + */ + retval = EINVAL; + end_addr = start_addr + count; + for (cur_addr = start_addr; cur_addr < end_addr; cur_addr++) { + ahd_outw(ahd, SEEDAT, *buf++); + ahd_outb(ahd, SEEADR, cur_addr); + ahd_outb(ahd, SEECTL, SEEOP_WRITE | SEESTART); + + retval = ahd_wait_seeprom(ahd); + if (retval) + break; + } + + /* + * Disable writes. + */ + ahd_outb(ahd, SEEADR, SEEOP_EWDS_ADDR); + ahd_outb(ahd, SEECTL, SEEOP_EWDS | SEESTART); + error = ahd_wait_seeprom(ahd); + if (error) + return (error); + return (retval); +} + +/* + * Wait ~100us for the serial eeprom to satisfy our request. + */ +static int +ahd_wait_seeprom(struct ahd_softc *ahd) +{ + int cnt; + + cnt = 5000; + while ((ahd_inb(ahd, SEESTAT) & (SEEARBACK|SEEBUSY)) != 0 && --cnt) + ahd_delay(5); + + if (cnt == 0) + return (ETIMEDOUT); + return (0); +} + +/* + * Validate the two checksums in the per_channel + * vital product data struct. + */ +static int +ahd_verify_vpd_cksum(struct vpd_config *vpd) +{ + int i; + int maxaddr; + uint32_t checksum; + uint8_t *vpdarray; + + vpdarray = (uint8_t *)vpd; + maxaddr = offsetof(struct vpd_config, vpd_checksum); + checksum = 0; + for (i = offsetof(struct vpd_config, resource_type); i < maxaddr; i++) + checksum = checksum + vpdarray[i]; + if (checksum == 0 + || (-checksum & 0xFF) != vpd->vpd_checksum) + return (0); + + checksum = 0; + maxaddr = offsetof(struct vpd_config, checksum); + for (i = offsetof(struct vpd_config, default_target_flags); + i < maxaddr; i++) + checksum = checksum + vpdarray[i]; + if (checksum == 0 + || (-checksum & 0xFF) != vpd->checksum) + return (0); + return (1); +} + +int +ahd_verify_cksum(struct seeprom_config *sc) +{ + int i; + int maxaddr; + uint32_t checksum; + uint16_t *scarray; + + maxaddr = (sizeof(*sc)/2) - 1; + checksum = 0; + scarray = (uint16_t *)sc; + + for (i = 0; i < maxaddr; i++) + checksum = checksum + scarray[i]; + if (checksum == 0 + || (checksum & 0xFFFF) != sc->checksum) { + return (0); + } else { + return (1); + } +} + +int +ahd_acquire_seeprom(struct ahd_softc *ahd) +{ + /* + * We should be able to determine the SEEPROM type + * from the flexport logic, but unfortunately not + * all implementations have this logic and there is + * no programatic method for determining if the logic + * is present. + */ + return (1); +#if 0 + uint8_t seetype; + int error; + + error = ahd_read_flexport(ahd, FLXADDR_ROMSTAT_CURSENSECTL, &seetype); + if (error != 0 + || ((seetype & FLX_ROMSTAT_SEECFG) == FLX_ROMSTAT_SEE_NONE)) + return (0); + return (1); +#endif +} + +void +ahd_release_seeprom(struct ahd_softc *ahd) +{ + /* Currently a no-op */ +} + +/* + * Wait at most 2 seconds for flexport arbitration to succeed. + */ +static int +ahd_wait_flexport(struct ahd_softc *ahd) +{ + int cnt; + + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + cnt = 1000000 * 2 / 5; + while ((ahd_inb(ahd, BRDCTL) & FLXARBACK) == 0 && --cnt) + ahd_delay(5); + + if (cnt == 0) + return (ETIMEDOUT); + return (0); +} + +int +ahd_write_flexport(struct ahd_softc *ahd, u_int addr, u_int value) +{ + int error; + + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + if (addr > 7) + panic("ahd_write_flexport: address out of range"); + ahd_outb(ahd, BRDCTL, BRDEN|(addr << 3)); + error = ahd_wait_flexport(ahd); + if (error != 0) + return (error); + ahd_outb(ahd, BRDDAT, value); + ahd_flush_device_writes(ahd); + ahd_outb(ahd, BRDCTL, BRDSTB|BRDEN|(addr << 3)); + ahd_flush_device_writes(ahd); + ahd_outb(ahd, BRDCTL, BRDEN|(addr << 3)); + ahd_flush_device_writes(ahd); + ahd_outb(ahd, BRDCTL, 0); + ahd_flush_device_writes(ahd); + return (0); +} + +int +ahd_read_flexport(struct ahd_softc *ahd, u_int addr, uint8_t *value) +{ + int error; + + AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK); + if (addr > 7) + panic("ahd_read_flexport: address out of range"); + ahd_outb(ahd, BRDCTL, BRDRW|BRDEN|(addr << 3)); + error = ahd_wait_flexport(ahd); + if (error != 0) + return (error); + *value = ahd_inb(ahd, BRDDAT); + ahd_outb(ahd, BRDCTL, 0); + ahd_flush_device_writes(ahd); + return (0); +} + +/************************* Target Mode ****************************************/ +#ifdef AHD_TARGET_MODE +cam_status +ahd_find_tmode_devs(struct ahd_softc *ahd, struct cam_sim *sim, union ccb *ccb, + struct ahd_tmode_tstate **tstate, + struct ahd_tmode_lstate **lstate, + int notfound_failure) +{ + + if ((ahd->features & AHD_TARGETMODE) == 0) + return (CAM_REQ_INVALID); + + /* + * Handle the 'black hole' device that sucks up + * requests to unattached luns on enabled targets. + */ + if (ccb->ccb_h.target_id == CAM_TARGET_WILDCARD + && ccb->ccb_h.target_lun == CAM_LUN_WILDCARD) { + *tstate = NULL; + *lstate = ahd->black_hole; + } else { + u_int max_id; + + max_id = (ahd->features & AHD_WIDE) ? 16 : 8; + if (ccb->ccb_h.target_id >= max_id) + return (CAM_TID_INVALID); + + if (ccb->ccb_h.target_lun >= AHD_NUM_LUNS) + return (CAM_LUN_INVALID); + + *tstate = ahd->enabled_targets[ccb->ccb_h.target_id]; + *lstate = NULL; + if (*tstate != NULL) + *lstate = + (*tstate)->enabled_luns[ccb->ccb_h.target_lun]; + } + + if (notfound_failure != 0 && *lstate == NULL) + return (CAM_PATH_INVALID); + + return (CAM_REQ_CMP); +} + +void +ahd_handle_en_lun(struct ahd_softc *ahd, struct cam_sim *sim, union ccb *ccb) +{ +#if NOT_YET + struct ahd_tmode_tstate *tstate; + struct ahd_tmode_lstate *lstate; + struct ccb_en_lun *cel; + cam_status status; + u_int target; + u_int lun; + u_int target_mask; + u_long s; + char channel; + + status = ahd_find_tmode_devs(ahd, sim, ccb, &tstate, &lstate, + /*notfound_failure*/FALSE); + + if (status != CAM_REQ_CMP) { + ccb->ccb_h.status = status; + return; + } + + if ((ahd->features & AHD_MULTIROLE) != 0) { + u_int our_id; + + our_id = ahd->our_id; + if (ccb->ccb_h.target_id != our_id) { + if ((ahd->features & AHD_MULTI_TID) != 0 + && (ahd->flags & AHD_INITIATORROLE) != 0) { + /* + * Only allow additional targets if + * the initiator role is disabled. + * The hardware cannot handle a re-select-in + * on the initiator id during a re-select-out + * on a different target id. + */ + status = CAM_TID_INVALID; + } else if ((ahd->flags & AHD_INITIATORROLE) != 0 + || ahd->enabled_luns > 0) { + /* + * Only allow our target id to change + * if the initiator role is not configured + * and there are no enabled luns which + * are attached to the currently registered + * scsi id. + */ + status = CAM_TID_INVALID; + } + } + } + + if (status != CAM_REQ_CMP) { + ccb->ccb_h.status = status; + return; + } + + /* + * We now have an id that is valid. + * If we aren't in target mode, switch modes. + */ + if ((ahd->flags & AHD_TARGETROLE) == 0 + && ccb->ccb_h.target_id != CAM_TARGET_WILDCARD) { + u_long s; + + printk("Configuring Target Mode\n"); + ahd_lock(ahd, &s); + if (LIST_FIRST(&ahd->pending_scbs) != NULL) { + ccb->ccb_h.status = CAM_BUSY; + ahd_unlock(ahd, &s); + return; + } + ahd->flags |= AHD_TARGETROLE; + if ((ahd->features & AHD_MULTIROLE) == 0) + ahd->flags &= ~AHD_INITIATORROLE; + ahd_pause(ahd); + ahd_loadseq(ahd); + ahd_restart(ahd); + ahd_unlock(ahd, &s); + } + cel = &ccb->cel; + target = ccb->ccb_h.target_id; + lun = ccb->ccb_h.target_lun; + channel = SIM_CHANNEL(ahd, sim); + target_mask = 0x01 << target; + if (channel == 'B') + target_mask <<= 8; + + if (cel->enable != 0) { + u_int scsiseq1; + + /* Are we already enabled?? */ + if (lstate != NULL) { + xpt_print_path(ccb->ccb_h.path); + printk("Lun already enabled\n"); + ccb->ccb_h.status = CAM_LUN_ALRDY_ENA; + return; + } + + if (cel->grp6_len != 0 + || cel->grp7_len != 0) { + /* + * Don't (yet?) support vendor + * specific commands. + */ + ccb->ccb_h.status = CAM_REQ_INVALID; + printk("Non-zero Group Codes\n"); + return; + } + + /* + * Seems to be okay. + * Setup our data structures. + */ + if (target != CAM_TARGET_WILDCARD && tstate == NULL) { + tstate = ahd_alloc_tstate(ahd, target, channel); + if (tstate == NULL) { + xpt_print_path(ccb->ccb_h.path); + printk("Couldn't allocate tstate\n"); + ccb->ccb_h.status = CAM_RESRC_UNAVAIL; + return; + } + } + lstate = kzalloc(sizeof(*lstate), GFP_ATOMIC); + if (lstate == NULL) { + xpt_print_path(ccb->ccb_h.path); + printk("Couldn't allocate lstate\n"); + ccb->ccb_h.status = CAM_RESRC_UNAVAIL; + return; + } + status = xpt_create_path(&lstate->path, /*periph*/NULL, + xpt_path_path_id(ccb->ccb_h.path), + xpt_path_target_id(ccb->ccb_h.path), + xpt_path_lun_id(ccb->ccb_h.path)); + if (status != CAM_REQ_CMP) { + kfree(lstate); + xpt_print_path(ccb->ccb_h.path); + printk("Couldn't allocate path\n"); + ccb->ccb_h.status = CAM_RESRC_UNAVAIL; + return; + } + SLIST_INIT(&lstate->accept_tios); + SLIST_INIT(&lstate->immed_notifies); + ahd_lock(ahd, &s); + ahd_pause(ahd); + if (target != CAM_TARGET_WILDCARD) { + tstate->enabled_luns[lun] = lstate; + ahd->enabled_luns++; + + if ((ahd->features & AHD_MULTI_TID) != 0) { + u_int targid_mask; + + targid_mask = ahd_inw(ahd, TARGID); + targid_mask |= target_mask; + ahd_outw(ahd, TARGID, targid_mask); + ahd_update_scsiid(ahd, targid_mask); + } else { + u_int our_id; + char channel; + + channel = SIM_CHANNEL(ahd, sim); + our_id = SIM_SCSI_ID(ahd, sim); + + /* + * This can only happen if selections + * are not enabled + */ + if (target != our_id) { + u_int sblkctl; + char cur_channel; + int swap; + + sblkctl = ahd_inb(ahd, SBLKCTL); + cur_channel = (sblkctl & SELBUSB) + ? 'B' : 'A'; + if ((ahd->features & AHD_TWIN) == 0) + cur_channel = 'A'; + swap = cur_channel != channel; + ahd->our_id = target; + + if (swap) + ahd_outb(ahd, SBLKCTL, + sblkctl ^ SELBUSB); + + ahd_outb(ahd, SCSIID, target); + + if (swap) + ahd_outb(ahd, SBLKCTL, sblkctl); + } + } + } else + ahd->black_hole = lstate; + /* Allow select-in operations */ + if (ahd->black_hole != NULL && ahd->enabled_luns > 0) { + scsiseq1 = ahd_inb(ahd, SCSISEQ_TEMPLATE); + scsiseq1 |= ENSELI; + ahd_outb(ahd, SCSISEQ_TEMPLATE, scsiseq1); + scsiseq1 = ahd_inb(ahd, SCSISEQ1); + scsiseq1 |= ENSELI; + ahd_outb(ahd, SCSISEQ1, scsiseq1); + } + ahd_unpause(ahd); + ahd_unlock(ahd, &s); + ccb->ccb_h.status = CAM_REQ_CMP; + xpt_print_path(ccb->ccb_h.path); + printk("Lun now enabled for target mode\n"); + } else { + struct scb *scb; + int i, empty; + + if (lstate == NULL) { + ccb->ccb_h.status = CAM_LUN_INVALID; + return; + } + + ahd_lock(ahd, &s); + + ccb->ccb_h.status = CAM_REQ_CMP; + LIST_FOREACH(scb, &ahd->pending_scbs, pending_links) { + struct ccb_hdr *ccbh; + + ccbh = &scb->io_ctx->ccb_h; + if (ccbh->func_code == XPT_CONT_TARGET_IO + && !xpt_path_comp(ccbh->path, ccb->ccb_h.path)){ + printk("CTIO pending\n"); + ccb->ccb_h.status = CAM_REQ_INVALID; + ahd_unlock(ahd, &s); + return; + } + } + + if (SLIST_FIRST(&lstate->accept_tios) != NULL) { + printk("ATIOs pending\n"); + ccb->ccb_h.status = CAM_REQ_INVALID; + } + + if (SLIST_FIRST(&lstate->immed_notifies) != NULL) { + printk("INOTs pending\n"); + ccb->ccb_h.status = CAM_REQ_INVALID; + } + + if (ccb->ccb_h.status != CAM_REQ_CMP) { + ahd_unlock(ahd, &s); + return; + } + + xpt_print_path(ccb->ccb_h.path); + printk("Target mode disabled\n"); + xpt_free_path(lstate->path); + kfree(lstate); + + ahd_pause(ahd); + /* Can we clean up the target too? */ + if (target != CAM_TARGET_WILDCARD) { + tstate->enabled_luns[lun] = NULL; + ahd->enabled_luns--; + for (empty = 1, i = 0; i < 8; i++) + if (tstate->enabled_luns[i] != NULL) { + empty = 0; + break; + } + + if (empty) { + ahd_free_tstate(ahd, target, channel, + /*force*/FALSE); + if (ahd->features & AHD_MULTI_TID) { + u_int targid_mask; + + targid_mask = ahd_inw(ahd, TARGID); + targid_mask &= ~target_mask; + ahd_outw(ahd, TARGID, targid_mask); + ahd_update_scsiid(ahd, targid_mask); + } + } + } else { + + ahd->black_hole = NULL; + + /* + * We can't allow selections without + * our black hole device. + */ + empty = TRUE; + } + if (ahd->enabled_luns == 0) { + /* Disallow select-in */ + u_int scsiseq1; + + scsiseq1 = ahd_inb(ahd, SCSISEQ_TEMPLATE); + scsiseq1 &= ~ENSELI; + ahd_outb(ahd, SCSISEQ_TEMPLATE, scsiseq1); + scsiseq1 = ahd_inb(ahd, SCSISEQ1); + scsiseq1 &= ~ENSELI; + ahd_outb(ahd, SCSISEQ1, scsiseq1); + + if ((ahd->features & AHD_MULTIROLE) == 0) { + printk("Configuring Initiator Mode\n"); + ahd->flags &= ~AHD_TARGETROLE; + ahd->flags |= AHD_INITIATORROLE; + ahd_pause(ahd); + ahd_loadseq(ahd); + ahd_restart(ahd); + /* + * Unpaused. The extra unpause + * that follows is harmless. + */ + } + } + ahd_unpause(ahd); + ahd_unlock(ahd, &s); + } +#endif +} + +static void +ahd_update_scsiid(struct ahd_softc *ahd, u_int targid_mask) +{ +#if NOT_YET + u_int scsiid_mask; + u_int scsiid; + + if ((ahd->features & AHD_MULTI_TID) == 0) + panic("ahd_update_scsiid called on non-multitid unit\n"); + + /* + * Since we will rely on the TARGID mask + * for selection enables, ensure that OID + * in SCSIID is not set to some other ID + * that we don't want to allow selections on. + */ + if ((ahd->features & AHD_ULTRA2) != 0) + scsiid = ahd_inb(ahd, SCSIID_ULTRA2); + else + scsiid = ahd_inb(ahd, SCSIID); + scsiid_mask = 0x1 << (scsiid & OID); + if ((targid_mask & scsiid_mask) == 0) { + u_int our_id; + + /* ffs counts from 1 */ + our_id = ffs(targid_mask); + if (our_id == 0) + our_id = ahd->our_id; + else + our_id--; + scsiid &= TID; + scsiid |= our_id; + } + if ((ahd->features & AHD_ULTRA2) != 0) + ahd_outb(ahd, SCSIID_ULTRA2, scsiid); + else + ahd_outb(ahd, SCSIID, scsiid); +#endif +} + +static void +ahd_run_tqinfifo(struct ahd_softc *ahd, int paused) +{ + struct target_cmd *cmd; + + ahd_sync_tqinfifo(ahd, BUS_DMASYNC_POSTREAD); + while ((cmd = &ahd->targetcmds[ahd->tqinfifonext])->cmd_valid != 0) { + + /* + * Only advance through the queue if we + * have the resources to process the command. + */ + if (ahd_handle_target_cmd(ahd, cmd) != 0) + break; + + cmd->cmd_valid = 0; + ahd_dmamap_sync(ahd, ahd->shared_data_dmat, + ahd->shared_data_map.dmamap, + ahd_targetcmd_offset(ahd, ahd->tqinfifonext), + sizeof(struct target_cmd), + BUS_DMASYNC_PREREAD); + ahd->tqinfifonext++; + + /* + * Lazily update our position in the target mode incoming + * command queue as seen by the sequencer. + */ + if ((ahd->tqinfifonext & (HOST_TQINPOS - 1)) == 1) { + u_int hs_mailbox; + + hs_mailbox = ahd_inb(ahd, HS_MAILBOX); + hs_mailbox &= ~HOST_TQINPOS; + hs_mailbox |= ahd->tqinfifonext & HOST_TQINPOS; + ahd_outb(ahd, HS_MAILBOX, hs_mailbox); + } + } +} + +static int +ahd_handle_target_cmd(struct ahd_softc *ahd, struct target_cmd *cmd) +{ + struct ahd_tmode_tstate *tstate; + struct ahd_tmode_lstate *lstate; + struct ccb_accept_tio *atio; + uint8_t *byte; + int initiator; + int target; + int lun; + + initiator = SCSIID_TARGET(ahd, cmd->scsiid); + target = SCSIID_OUR_ID(cmd->scsiid); + lun = (cmd->identify & MSG_IDENTIFY_LUNMASK); + + byte = cmd->bytes; + tstate = ahd->enabled_targets[target]; + lstate = NULL; + if (tstate != NULL) + lstate = tstate->enabled_luns[lun]; + + /* + * Commands for disabled luns go to the black hole driver. + */ + if (lstate == NULL) + lstate = ahd->black_hole; + + atio = (struct ccb_accept_tio*)SLIST_FIRST(&lstate->accept_tios); + if (atio == NULL) { + ahd->flags |= AHD_TQINFIFO_BLOCKED; + /* + * Wait for more ATIOs from the peripheral driver for this lun. + */ + return (1); + } else + ahd->flags &= ~AHD_TQINFIFO_BLOCKED; +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_TQIN) != 0) + printk("Incoming command from %d for %d:%d%s\n", + initiator, target, lun, + lstate == ahd->black_hole ? "(Black Holed)" : ""); +#endif + SLIST_REMOVE_HEAD(&lstate->accept_tios, sim_links.sle); + + if (lstate == ahd->black_hole) { + /* Fill in the wildcards */ + atio->ccb_h.target_id = target; + atio->ccb_h.target_lun = lun; + } + + /* + * Package it up and send it off to + * whomever has this lun enabled. + */ + atio->sense_len = 0; + atio->init_id = initiator; + if (byte[0] != 0xFF) { + /* Tag was included */ + atio->tag_action = *byte++; + atio->tag_id = *byte++; + atio->ccb_h.flags = CAM_TAG_ACTION_VALID; + } else { + atio->ccb_h.flags = 0; + } + byte++; + + /* Okay. Now determine the cdb size based on the command code */ + switch (*byte >> CMD_GROUP_CODE_SHIFT) { + case 0: + atio->cdb_len = 6; + break; + case 1: + case 2: + atio->cdb_len = 10; + break; + case 4: + atio->cdb_len = 16; + break; + case 5: + atio->cdb_len = 12; + break; + case 3: + default: + /* Only copy the opcode. */ + atio->cdb_len = 1; + printk("Reserved or VU command code type encountered\n"); + break; + } + + memcpy(atio->cdb_io.cdb_bytes, byte, atio->cdb_len); + + atio->ccb_h.status |= CAM_CDB_RECVD; + + if ((cmd->identify & MSG_IDENTIFY_DISCFLAG) == 0) { + /* + * We weren't allowed to disconnect. + * We're hanging on the bus until a + * continue target I/O comes in response + * to this accept tio. + */ +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_TQIN) != 0) + printk("Received Immediate Command %d:%d:%d - %p\n", + initiator, target, lun, ahd->pending_device); +#endif + ahd->pending_device = lstate; + ahd_freeze_ccb((union ccb *)atio); + atio->ccb_h.flags |= CAM_DIS_DISCONNECT; + } + xpt_done((union ccb*)atio); + return (0); +} + +#endif diff --git a/drivers/scsi/aic7xxx/aic79xx_inline.h b/drivers/scsi/aic7xxx/aic79xx_inline.h new file mode 100644 index 000000000..09335a3c8 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx_inline.h @@ -0,0 +1,172 @@ +/* + * Inline routines shareable across OS platforms. + * + * Copyright (c) 1994-2001 Justin T. Gibbs. + * Copyright (c) 2000-2003 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aic79xx_inline.h#59 $ + * + * $FreeBSD$ + */ + +#ifndef _AIC79XX_INLINE_H_ +#define _AIC79XX_INLINE_H_ + +/******************************** Debugging ***********************************/ +static inline char *ahd_name(struct ahd_softc *ahd); + +static inline char *ahd_name(struct ahd_softc *ahd) +{ + return (ahd->name); +} + +/************************ Sequencer Execution Control *************************/ +static inline void ahd_known_modes(struct ahd_softc *ahd, + ahd_mode src, ahd_mode dst); +static inline ahd_mode_state ahd_build_mode_state(struct ahd_softc *ahd, + ahd_mode src, + ahd_mode dst); +static inline void ahd_extract_mode_state(struct ahd_softc *ahd, + ahd_mode_state state, + ahd_mode *src, ahd_mode *dst); + +void ahd_set_modes(struct ahd_softc *ahd, ahd_mode src, + ahd_mode dst); +ahd_mode_state ahd_save_modes(struct ahd_softc *ahd); +void ahd_restore_modes(struct ahd_softc *ahd, + ahd_mode_state state); +int ahd_is_paused(struct ahd_softc *ahd); +void ahd_pause(struct ahd_softc *ahd); +void ahd_unpause(struct ahd_softc *ahd); + +static inline void +ahd_known_modes(struct ahd_softc *ahd, ahd_mode src, ahd_mode dst) +{ + ahd->src_mode = src; + ahd->dst_mode = dst; + ahd->saved_src_mode = src; + ahd->saved_dst_mode = dst; +} + +static inline ahd_mode_state +ahd_build_mode_state(struct ahd_softc *ahd, ahd_mode src, ahd_mode dst) +{ + return ((src << SRC_MODE_SHIFT) | (dst << DST_MODE_SHIFT)); +} + +static inline void +ahd_extract_mode_state(struct ahd_softc *ahd, ahd_mode_state state, + ahd_mode *src, ahd_mode *dst) +{ + *src = (state & SRC_MODE) >> SRC_MODE_SHIFT; + *dst = (state & DST_MODE) >> DST_MODE_SHIFT; +} + +/*********************** Scatter Gather List Handling *************************/ +void *ahd_sg_setup(struct ahd_softc *ahd, struct scb *scb, + void *sgptr, dma_addr_t addr, + bus_size_t len, int last); + +/************************** Memory mapping routines ***************************/ +static inline size_t ahd_sg_size(struct ahd_softc *ahd); + +void ahd_sync_sglist(struct ahd_softc *ahd, + struct scb *scb, int op); + +static inline size_t ahd_sg_size(struct ahd_softc *ahd) +{ + if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) + return (sizeof(struct ahd_dma64_seg)); + return (sizeof(struct ahd_dma_seg)); +} + +/*********************** Miscellaneous Support Functions ***********************/ +struct ahd_initiator_tinfo * + ahd_fetch_transinfo(struct ahd_softc *ahd, + char channel, u_int our_id, + u_int remote_id, + struct ahd_tmode_tstate **tstate); +uint16_t + ahd_inw(struct ahd_softc *ahd, u_int port); +void ahd_outw(struct ahd_softc *ahd, u_int port, + u_int value); +uint32_t + ahd_inl(struct ahd_softc *ahd, u_int port); +void ahd_outl(struct ahd_softc *ahd, u_int port, + uint32_t value); +uint64_t + ahd_inq(struct ahd_softc *ahd, u_int port); +void ahd_outq(struct ahd_softc *ahd, u_int port, + uint64_t value); +u_int ahd_get_scbptr(struct ahd_softc *ahd); +void ahd_set_scbptr(struct ahd_softc *ahd, u_int scbptr); +u_int ahd_inb_scbram(struct ahd_softc *ahd, u_int offset); +u_int ahd_inw_scbram(struct ahd_softc *ahd, u_int offset); +struct scb * + ahd_lookup_scb(struct ahd_softc *ahd, u_int tag); +void ahd_queue_scb(struct ahd_softc *ahd, struct scb *scb); + +static inline uint8_t *ahd_get_sense_buf(struct ahd_softc *ahd, + struct scb *scb); +static inline uint32_t ahd_get_sense_bufaddr(struct ahd_softc *ahd, + struct scb *scb); + +#if 0 /* unused */ + +#define AHD_COPY_COL_IDX(dst, src) \ +do { \ + dst->hscb->scsiid = src->hscb->scsiid; \ + dst->hscb->lun = src->hscb->lun; \ +} while (0) + +#endif + +static inline uint8_t * +ahd_get_sense_buf(struct ahd_softc *ahd, struct scb *scb) +{ + return (scb->sense_data); +} + +static inline uint32_t +ahd_get_sense_bufaddr(struct ahd_softc *ahd, struct scb *scb) +{ + return (scb->sense_busaddr); +} + +/************************** Interrupt Processing ******************************/ +int ahd_intr(struct ahd_softc *ahd); + +#endif /* _AIC79XX_INLINE_H_ */ diff --git a/drivers/scsi/aic7xxx/aic79xx_osm.c b/drivers/scsi/aic7xxx/aic79xx_osm.c new file mode 100644 index 000000000..f32398939 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx_osm.c @@ -0,0 +1,2863 @@ +/* + * Adaptec AIC79xx device driver for Linux. + * + * $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic79xx_osm.c#171 $ + * + * -------------------------------------------------------------------------- + * Copyright (c) 1994-2000 Justin T. Gibbs. + * Copyright (c) 1997-1999 Doug Ledford + * Copyright (c) 2000-2003 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + */ + +#include "aic79xx_osm.h" +#include "aic79xx_inline.h" +#include <scsi/scsicam.h> + +static struct scsi_transport_template *ahd_linux_transport_template = NULL; + +#include <linux/init.h> /* __setup */ +#include <linux/mm.h> /* For fetching system memory size */ +#include <linux/blkdev.h> /* For block_size() */ +#include <linux/delay.h> /* For ssleep/msleep */ +#include <linux/device.h> +#include <linux/slab.h> + +/* + * Bucket size for counting good commands in between bad ones. + */ +#define AHD_LINUX_ERR_THRESH 1000 + +/* + * Set this to the delay in seconds after SCSI bus reset. + * Note, we honor this only for the initial bus reset. + * The scsi error recovery code performs its own bus settle + * delay handling for error recovery actions. + */ +#ifdef CONFIG_AIC79XX_RESET_DELAY_MS +#define AIC79XX_RESET_DELAY CONFIG_AIC79XX_RESET_DELAY_MS +#else +#define AIC79XX_RESET_DELAY 5000 +#endif + +/* + * To change the default number of tagged transactions allowed per-device, + * add a line to the lilo.conf file like: + * append="aic79xx=verbose,tag_info:{{32,32,32,32},{32,32,32,32}}" + * which will result in the first four devices on the first two + * controllers being set to a tagged queue depth of 32. + * + * The tag_commands is an array of 16 to allow for wide and twin adapters. + * Twin adapters will use indexes 0-7 for channel 0, and indexes 8-15 + * for channel 1. + */ +typedef struct { + uint16_t tag_commands[16]; /* Allow for wide/twin adapters. */ +} adapter_tag_info_t; + +/* + * Modify this as you see fit for your system. + * + * 0 tagged queuing disabled + * 1 <= n <= 253 n == max tags ever dispatched. + * + * The driver will throttle the number of commands dispatched to a + * device if it returns queue full. For devices with a fixed maximum + * queue depth, the driver will eventually determine this depth and + * lock it in (a console message is printed to indicate that a lock + * has occurred). On some devices, queue full is returned for a temporary + * resource shortage. These devices will return queue full at varying + * depths. The driver will throttle back when the queue fulls occur and + * attempt to slowly increase the depth over time as the device recovers + * from the resource shortage. + * + * In this example, the first line will disable tagged queueing for all + * the devices on the first probed aic79xx adapter. + * + * The second line enables tagged queueing with 4 commands/LUN for IDs + * (0, 2-11, 13-15), disables tagged queueing for ID 12, and tells the + * driver to attempt to use up to 64 tags for ID 1. + * + * The third line is the same as the first line. + * + * The fourth line disables tagged queueing for devices 0 and 3. It + * enables tagged queueing for the other IDs, with 16 commands/LUN + * for IDs 1 and 4, 127 commands/LUN for ID 8, and 4 commands/LUN for + * IDs 2, 5-7, and 9-15. + */ + +/* + * NOTE: The below structure is for reference only, the actual structure + * to modify in order to change things is just below this comment block. +adapter_tag_info_t aic79xx_tag_info[] = +{ + {{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}}, + {{4, 64, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 0, 4, 4, 4}}, + {{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}}, + {{0, 16, 4, 0, 16, 4, 4, 4, 127, 4, 4, 4, 4, 4, 4, 4}} +}; +*/ + +#ifdef CONFIG_AIC79XX_CMDS_PER_DEVICE +#define AIC79XX_CMDS_PER_DEVICE CONFIG_AIC79XX_CMDS_PER_DEVICE +#else +#define AIC79XX_CMDS_PER_DEVICE AHD_MAX_QUEUE +#endif + +#define AIC79XX_CONFIGED_TAG_COMMANDS { \ + AIC79XX_CMDS_PER_DEVICE, AIC79XX_CMDS_PER_DEVICE, \ + AIC79XX_CMDS_PER_DEVICE, AIC79XX_CMDS_PER_DEVICE, \ + AIC79XX_CMDS_PER_DEVICE, AIC79XX_CMDS_PER_DEVICE, \ + AIC79XX_CMDS_PER_DEVICE, AIC79XX_CMDS_PER_DEVICE, \ + AIC79XX_CMDS_PER_DEVICE, AIC79XX_CMDS_PER_DEVICE, \ + AIC79XX_CMDS_PER_DEVICE, AIC79XX_CMDS_PER_DEVICE, \ + AIC79XX_CMDS_PER_DEVICE, AIC79XX_CMDS_PER_DEVICE, \ + AIC79XX_CMDS_PER_DEVICE, AIC79XX_CMDS_PER_DEVICE \ +} + +/* + * By default, use the number of commands specified by + * the users kernel configuration. + */ +static adapter_tag_info_t aic79xx_tag_info[] = +{ + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS}, + {AIC79XX_CONFIGED_TAG_COMMANDS} +}; + +/* + * The I/O cell on the chip is very configurable in respect to its analog + * characteristics. Set the defaults here; they can be overriden with + * the proper insmod parameters. + */ +struct ahd_linux_iocell_opts +{ + uint8_t precomp; + uint8_t slewrate; + uint8_t amplitude; +}; +#define AIC79XX_DEFAULT_PRECOMP 0xFF +#define AIC79XX_DEFAULT_SLEWRATE 0xFF +#define AIC79XX_DEFAULT_AMPLITUDE 0xFF +#define AIC79XX_DEFAULT_IOOPTS \ +{ \ + AIC79XX_DEFAULT_PRECOMP, \ + AIC79XX_DEFAULT_SLEWRATE, \ + AIC79XX_DEFAULT_AMPLITUDE \ +} +#define AIC79XX_PRECOMP_INDEX 0 +#define AIC79XX_SLEWRATE_INDEX 1 +#define AIC79XX_AMPLITUDE_INDEX 2 +static const struct ahd_linux_iocell_opts aic79xx_iocell_info[] = +{ + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS, + AIC79XX_DEFAULT_IOOPTS +}; + +/* + * There should be a specific return value for this in scsi.h, but + * it seems that most drivers ignore it. + */ +#define DID_UNDERFLOW DID_ERROR + +void +ahd_print_path(struct ahd_softc *ahd, struct scb *scb) +{ + printk("(scsi%d:%c:%d:%d): ", + ahd->platform_data->host->host_no, + scb != NULL ? SCB_GET_CHANNEL(ahd, scb) : 'X', + scb != NULL ? SCB_GET_TARGET(ahd, scb) : -1, + scb != NULL ? SCB_GET_LUN(scb) : -1); +} + +/* + * XXX - these options apply unilaterally to _all_ adapters + * cards in the system. This should be fixed. Exceptions to this + * rule are noted in the comments. + */ + +/* + * Skip the scsi bus reset. Non 0 make us skip the reset at startup. This + * has no effect on any later resets that might occur due to things like + * SCSI bus timeouts. + */ +static uint32_t aic79xx_no_reset; + +/* + * Should we force EXTENDED translation on a controller. + * 0 == Use whatever is in the SEEPROM or default to off + * 1 == Use whatever is in the SEEPROM or default to on + */ +static uint32_t aic79xx_extended; + +/* + * PCI bus parity checking of the Adaptec controllers. This is somewhat + * dubious at best. To my knowledge, this option has never actually + * solved a PCI parity problem, but on certain machines with broken PCI + * chipset configurations, it can generate tons of false error messages. + * It's included in the driver for completeness. + * 0 = Shut off PCI parity check + * non-0 = Enable PCI parity check + * + * NOTE: you can't actually pass -1 on the lilo prompt. So, to set this + * variable to -1 you would actually want to simply pass the variable + * name without a number. That will invert the 0 which will result in + * -1. + */ +static uint32_t aic79xx_pci_parity = ~0; + +/* + * There are lots of broken chipsets in the world. Some of them will + * violate the PCI spec when we issue byte sized memory writes to our + * controller. I/O mapped register access, if allowed by the given + * platform, will work in almost all cases. + */ +uint32_t aic79xx_allow_memio = ~0; + +/* + * So that we can set how long each device is given as a selection timeout. + * The table of values goes like this: + * 0 - 256ms + * 1 - 128ms + * 2 - 64ms + * 3 - 32ms + * We default to 256ms because some older devices need a longer time + * to respond to initial selection. + */ +static uint32_t aic79xx_seltime; + +/* + * Certain devices do not perform any aging on commands. Should the + * device be saturated by commands in one portion of the disk, it is + * possible for transactions on far away sectors to never be serviced. + * To handle these devices, we can periodically send an ordered tag to + * force all outstanding transactions to be serviced prior to a new + * transaction. + */ +static uint32_t aic79xx_periodic_otag; + +/* Some storage boxes are using an LSI chip which has a bug making it + * impossible to use aic79xx Rev B chip in 320 speeds. The following + * storage boxes have been reported to be buggy: + * EonStor 3U 16-Bay: U16U-G3A3 + * EonStor 2U 12-Bay: U12U-G3A3 + * SentinelRAID: 2500F R5 / R6 + * SentinelRAID: 2500F R1 + * SentinelRAID: 2500F/1500F + * SentinelRAID: 150F + * + * To get around this LSI bug, you can set your board to 160 mode + * or you can enable the SLOWCRC bit. + */ +uint32_t aic79xx_slowcrc; + +/* + * Module information and settable options. + */ +static char *aic79xx = NULL; + +MODULE_AUTHOR("Maintainer: Hannes Reinecke <hare@suse.de>"); +MODULE_DESCRIPTION("Adaptec AIC790X U320 SCSI Host Bus Adapter driver"); +MODULE_LICENSE("Dual BSD/GPL"); +MODULE_VERSION(AIC79XX_DRIVER_VERSION); +module_param(aic79xx, charp, 0444); +MODULE_PARM_DESC(aic79xx, +"period-delimited options string:\n" +" verbose Enable verbose/diagnostic logging\n" +" allow_memio Allow device registers to be memory mapped\n" +" debug Bitmask of debug values to enable\n" +" no_reset Suppress initial bus resets\n" +" extended Enable extended geometry on all controllers\n" +" periodic_otag Send an ordered tagged transaction\n" +" periodically to prevent tag starvation.\n" +" This may be required by some older disk\n" +" or drives/RAID arrays.\n" +" tag_info:<tag_str> Set per-target tag depth\n" +" global_tag_depth:<int> Global tag depth for all targets on all buses\n" +" slewrate:<slewrate_list>Set the signal slew rate (0-15).\n" +" precomp:<pcomp_list> Set the signal precompensation (0-7).\n" +" amplitude:<int> Set the signal amplitude (0-7).\n" +" seltime:<int> Selection Timeout:\n" +" (0/256ms,1/128ms,2/64ms,3/32ms)\n" +" slowcrc Turn on the SLOWCRC bit (Rev B only)\n" +"\n" +" Sample modprobe configuration file:\n" +" # Enable verbose logging\n" +" # Set tag depth on Controller 2/Target 2 to 10 tags\n" +" # Shorten the selection timeout to 128ms\n" +"\n" +" options aic79xx 'aic79xx=verbose.tag_info:{{}.{}.{..10}}.seltime:1'\n" +); + +static void ahd_linux_handle_scsi_status(struct ahd_softc *, + struct scsi_device *, + struct scb *); +static void ahd_linux_queue_cmd_complete(struct ahd_softc *ahd, + struct scsi_cmnd *cmd); +static int ahd_linux_queue_abort_cmd(struct scsi_cmnd *cmd); +static void ahd_linux_initialize_scsi_bus(struct ahd_softc *ahd); +static u_int ahd_linux_user_tagdepth(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo); +static void ahd_linux_device_queue_depth(struct scsi_device *); +static int ahd_linux_run_command(struct ahd_softc*, + struct ahd_linux_device *, + struct scsi_cmnd *); +static void ahd_linux_setup_tag_info_global(char *p); +static int aic79xx_setup(char *c); +static void ahd_freeze_simq(struct ahd_softc *ahd); +static void ahd_release_simq(struct ahd_softc *ahd); + +static int ahd_linux_unit; + + +/************************** OS Utility Wrappers *******************************/ +void ahd_delay(long); +void +ahd_delay(long usec) +{ + /* + * udelay on Linux can have problems for + * multi-millisecond waits. Wait at most + * 1024us per call. + */ + while (usec > 0) { + udelay(usec % 1024); + usec -= 1024; + } +} + + +/***************************** Low Level I/O **********************************/ +uint8_t ahd_inb(struct ahd_softc * ahd, long port); +void ahd_outb(struct ahd_softc * ahd, long port, uint8_t val); +void ahd_outw_atomic(struct ahd_softc * ahd, + long port, uint16_t val); +void ahd_outsb(struct ahd_softc * ahd, long port, + uint8_t *, int count); +void ahd_insb(struct ahd_softc * ahd, long port, + uint8_t *, int count); + +uint8_t +ahd_inb(struct ahd_softc * ahd, long port) +{ + uint8_t x; + + if (ahd->tags[0] == BUS_SPACE_MEMIO) { + x = readb(ahd->bshs[0].maddr + port); + } else { + x = inb(ahd->bshs[(port) >> 8].ioport + ((port) & 0xFF)); + } + mb(); + return (x); +} + +#if 0 /* unused */ +static uint16_t +ahd_inw_atomic(struct ahd_softc * ahd, long port) +{ + uint8_t x; + + if (ahd->tags[0] == BUS_SPACE_MEMIO) { + x = readw(ahd->bshs[0].maddr + port); + } else { + x = inw(ahd->bshs[(port) >> 8].ioport + ((port) & 0xFF)); + } + mb(); + return (x); +} +#endif + +void +ahd_outb(struct ahd_softc * ahd, long port, uint8_t val) +{ + if (ahd->tags[0] == BUS_SPACE_MEMIO) { + writeb(val, ahd->bshs[0].maddr + port); + } else { + outb(val, ahd->bshs[(port) >> 8].ioport + (port & 0xFF)); + } + mb(); +} + +void +ahd_outw_atomic(struct ahd_softc * ahd, long port, uint16_t val) +{ + if (ahd->tags[0] == BUS_SPACE_MEMIO) { + writew(val, ahd->bshs[0].maddr + port); + } else { + outw(val, ahd->bshs[(port) >> 8].ioport + (port & 0xFF)); + } + mb(); +} + +void +ahd_outsb(struct ahd_softc * ahd, long port, uint8_t *array, int count) +{ + int i; + + /* + * There is probably a more efficient way to do this on Linux + * but we don't use this for anything speed critical and this + * should work. + */ + for (i = 0; i < count; i++) + ahd_outb(ahd, port, *array++); +} + +void +ahd_insb(struct ahd_softc * ahd, long port, uint8_t *array, int count) +{ + int i; + + /* + * There is probably a more efficient way to do this on Linux + * but we don't use this for anything speed critical and this + * should work. + */ + for (i = 0; i < count; i++) + *array++ = ahd_inb(ahd, port); +} + +/******************************* PCI Routines *********************************/ +uint32_t +ahd_pci_read_config(ahd_dev_softc_t pci, int reg, int width) +{ + switch (width) { + case 1: + { + uint8_t retval; + + pci_read_config_byte(pci, reg, &retval); + return (retval); + } + case 2: + { + uint16_t retval; + pci_read_config_word(pci, reg, &retval); + return (retval); + } + case 4: + { + uint32_t retval; + pci_read_config_dword(pci, reg, &retval); + return (retval); + } + default: + panic("ahd_pci_read_config: Read size too big"); + /* NOTREACHED */ + return (0); + } +} + +void +ahd_pci_write_config(ahd_dev_softc_t pci, int reg, uint32_t value, int width) +{ + switch (width) { + case 1: + pci_write_config_byte(pci, reg, value); + break; + case 2: + pci_write_config_word(pci, reg, value); + break; + case 4: + pci_write_config_dword(pci, reg, value); + break; + default: + panic("ahd_pci_write_config: Write size too big"); + /* NOTREACHED */ + } +} + +/****************************** Inlines ***************************************/ +static void ahd_linux_unmap_scb(struct ahd_softc*, struct scb*); + +static void +ahd_linux_unmap_scb(struct ahd_softc *ahd, struct scb *scb) +{ + struct scsi_cmnd *cmd; + + cmd = scb->io_ctx; + ahd_sync_sglist(ahd, scb, BUS_DMASYNC_POSTWRITE); + scsi_dma_unmap(cmd); +} + +/******************************** Macros **************************************/ +#define BUILD_SCSIID(ahd, cmd) \ + (((scmd_id(cmd) << TID_SHIFT) & TID) | (ahd)->our_id) + +/* + * Return a string describing the driver. + */ +static const char * +ahd_linux_info(struct Scsi_Host *host) +{ + static char buffer[512]; + char ahd_info[256]; + char *bp; + struct ahd_softc *ahd; + + bp = &buffer[0]; + ahd = *(struct ahd_softc **)host->hostdata; + memset(bp, 0, sizeof(buffer)); + strcpy(bp, "Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev " AIC79XX_DRIVER_VERSION "\n" + " <"); + strcat(bp, ahd->description); + strcat(bp, ">\n" + " "); + ahd_controller_info(ahd, ahd_info); + strcat(bp, ahd_info); + + return (bp); +} + +/* + * Queue an SCB to the controller. + */ +static int +ahd_linux_queue_lck(struct scsi_cmnd * cmd, void (*scsi_done) (struct scsi_cmnd *)) +{ + struct ahd_softc *ahd; + struct ahd_linux_device *dev = scsi_transport_device_data(cmd->device); + int rtn = SCSI_MLQUEUE_HOST_BUSY; + + ahd = *(struct ahd_softc **)cmd->device->host->hostdata; + + cmd->scsi_done = scsi_done; + cmd->result = CAM_REQ_INPROG << 16; + rtn = ahd_linux_run_command(ahd, dev, cmd); + + return rtn; +} + +static DEF_SCSI_QCMD(ahd_linux_queue) + +static struct scsi_target ** +ahd_linux_target_in_softc(struct scsi_target *starget) +{ + struct ahd_softc *ahd = + *((struct ahd_softc **)dev_to_shost(&starget->dev)->hostdata); + unsigned int target_offset; + + target_offset = starget->id; + if (starget->channel != 0) + target_offset += 8; + + return &ahd->platform_data->starget[target_offset]; +} + +static int +ahd_linux_target_alloc(struct scsi_target *starget) +{ + struct ahd_softc *ahd = + *((struct ahd_softc **)dev_to_shost(&starget->dev)->hostdata); + struct seeprom_config *sc = ahd->seep_config; + unsigned long flags; + struct scsi_target **ahd_targp = ahd_linux_target_in_softc(starget); + struct ahd_devinfo devinfo; + struct ahd_initiator_tinfo *tinfo; + struct ahd_tmode_tstate *tstate; + char channel = starget->channel + 'A'; + + ahd_lock(ahd, &flags); + + BUG_ON(*ahd_targp != NULL); + + *ahd_targp = starget; + + if (sc) { + int flags = sc->device_flags[starget->id]; + + tinfo = ahd_fetch_transinfo(ahd, 'A', ahd->our_id, + starget->id, &tstate); + + if ((flags & CFPACKETIZED) == 0) { + /* don't negotiate packetized (IU) transfers */ + spi_max_iu(starget) = 0; + } else { + if ((ahd->features & AHD_RTI) == 0) + spi_rti(starget) = 0; + } + + if ((flags & CFQAS) == 0) + spi_max_qas(starget) = 0; + + /* Transinfo values have been set to BIOS settings */ + spi_max_width(starget) = (flags & CFWIDEB) ? 1 : 0; + spi_min_period(starget) = tinfo->user.period; + spi_max_offset(starget) = tinfo->user.offset; + } + + tinfo = ahd_fetch_transinfo(ahd, channel, ahd->our_id, + starget->id, &tstate); + ahd_compile_devinfo(&devinfo, ahd->our_id, starget->id, + CAM_LUN_WILDCARD, channel, + ROLE_INITIATOR); + ahd_set_syncrate(ahd, &devinfo, 0, 0, 0, + AHD_TRANS_GOAL, /*paused*/FALSE); + ahd_set_width(ahd, &devinfo, MSG_EXT_WDTR_BUS_8_BIT, + AHD_TRANS_GOAL, /*paused*/FALSE); + ahd_unlock(ahd, &flags); + + return 0; +} + +static void +ahd_linux_target_destroy(struct scsi_target *starget) +{ + struct scsi_target **ahd_targp = ahd_linux_target_in_softc(starget); + + *ahd_targp = NULL; +} + +static int +ahd_linux_slave_alloc(struct scsi_device *sdev) +{ + struct ahd_softc *ahd = + *((struct ahd_softc **)sdev->host->hostdata); + struct ahd_linux_device *dev; + + if (bootverbose) + printk("%s: Slave Alloc %d\n", ahd_name(ahd), sdev->id); + + dev = scsi_transport_device_data(sdev); + memset(dev, 0, sizeof(*dev)); + + /* + * We start out life using untagged + * transactions of which we allow one. + */ + dev->openings = 1; + + /* + * Set maxtags to 0. This will be changed if we + * later determine that we are dealing with + * a tagged queuing capable device. + */ + dev->maxtags = 0; + + return (0); +} + +static int +ahd_linux_slave_configure(struct scsi_device *sdev) +{ + if (bootverbose) + sdev_printk(KERN_INFO, sdev, "Slave Configure\n"); + + ahd_linux_device_queue_depth(sdev); + + /* Initial Domain Validation */ + if (!spi_initial_dv(sdev->sdev_target)) + spi_dv_device(sdev); + + return 0; +} + +#if defined(__i386__) +/* + * Return the disk geometry for the given SCSI device. + */ +static int +ahd_linux_biosparam(struct scsi_device *sdev, struct block_device *bdev, + sector_t capacity, int geom[]) +{ + int heads; + int sectors; + int cylinders; + int extended; + struct ahd_softc *ahd; + + ahd = *((struct ahd_softc **)sdev->host->hostdata); + + if (scsi_partsize(bdev, capacity, geom)) + return 0; + + heads = 64; + sectors = 32; + cylinders = aic_sector_div(capacity, heads, sectors); + + if (aic79xx_extended != 0) + extended = 1; + else + extended = (ahd->flags & AHD_EXTENDED_TRANS_A) != 0; + if (extended && cylinders >= 1024) { + heads = 255; + sectors = 63; + cylinders = aic_sector_div(capacity, heads, sectors); + } + geom[0] = heads; + geom[1] = sectors; + geom[2] = cylinders; + return (0); +} +#endif + +/* + * Abort the current SCSI command(s). + */ +static int +ahd_linux_abort(struct scsi_cmnd *cmd) +{ + int error; + + error = ahd_linux_queue_abort_cmd(cmd); + + return error; +} + +/* + * Attempt to send a target reset message to the device that timed out. + */ +static int +ahd_linux_dev_reset(struct scsi_cmnd *cmd) +{ + struct ahd_softc *ahd; + struct ahd_linux_device *dev; + struct scb *reset_scb; + u_int cdb_byte; + int retval = SUCCESS; + struct ahd_initiator_tinfo *tinfo; + struct ahd_tmode_tstate *tstate; + unsigned long flags; + DECLARE_COMPLETION_ONSTACK(done); + + reset_scb = NULL; + + ahd = *(struct ahd_softc **)cmd->device->host->hostdata; + + scmd_printk(KERN_INFO, cmd, + "Attempting to queue a TARGET RESET message:"); + + printk("CDB:"); + for (cdb_byte = 0; cdb_byte < cmd->cmd_len; cdb_byte++) + printk(" 0x%x", cmd->cmnd[cdb_byte]); + printk("\n"); + + /* + * Determine if we currently own this command. + */ + dev = scsi_transport_device_data(cmd->device); + + if (dev == NULL) { + /* + * No target device for this command exists, + * so we must not still own the command. + */ + scmd_printk(KERN_INFO, cmd, "Is not an active device\n"); + return SUCCESS; + } + + /* + * Generate us a new SCB + */ + reset_scb = ahd_get_scb(ahd, AHD_NEVER_COL_IDX); + if (!reset_scb) { + scmd_printk(KERN_INFO, cmd, "No SCB available\n"); + return FAILED; + } + + tinfo = ahd_fetch_transinfo(ahd, 'A', ahd->our_id, + cmd->device->id, &tstate); + reset_scb->io_ctx = cmd; + reset_scb->platform_data->dev = dev; + reset_scb->sg_count = 0; + ahd_set_residual(reset_scb, 0); + ahd_set_sense_residual(reset_scb, 0); + reset_scb->platform_data->xfer_len = 0; + reset_scb->hscb->control = 0; + reset_scb->hscb->scsiid = BUILD_SCSIID(ahd,cmd); + reset_scb->hscb->lun = cmd->device->lun; + reset_scb->hscb->cdb_len = 0; + reset_scb->hscb->task_management = SIU_TASKMGMT_LUN_RESET; + reset_scb->flags |= SCB_DEVICE_RESET|SCB_RECOVERY_SCB|SCB_ACTIVE; + if ((tinfo->curr.ppr_options & MSG_EXT_PPR_IU_REQ) != 0) { + reset_scb->flags |= SCB_PACKETIZED; + } else { + reset_scb->hscb->control |= MK_MESSAGE; + } + dev->openings--; + dev->active++; + dev->commands_issued++; + + ahd_lock(ahd, &flags); + + LIST_INSERT_HEAD(&ahd->pending_scbs, reset_scb, pending_links); + ahd_queue_scb(ahd, reset_scb); + + ahd->platform_data->eh_done = &done; + ahd_unlock(ahd, &flags); + + printk("%s: Device reset code sleeping\n", ahd_name(ahd)); + if (!wait_for_completion_timeout(&done, 5 * HZ)) { + ahd_lock(ahd, &flags); + ahd->platform_data->eh_done = NULL; + ahd_unlock(ahd, &flags); + printk("%s: Device reset timer expired (active %d)\n", + ahd_name(ahd), dev->active); + retval = FAILED; + } + printk("%s: Device reset returning 0x%x\n", ahd_name(ahd), retval); + + return (retval); +} + +/* + * Reset the SCSI bus. + */ +static int +ahd_linux_bus_reset(struct scsi_cmnd *cmd) +{ + struct ahd_softc *ahd; + int found; + unsigned long flags; + + ahd = *(struct ahd_softc **)cmd->device->host->hostdata; +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_RECOVERY) != 0) + printk("%s: Bus reset called for cmd %p\n", + ahd_name(ahd), cmd); +#endif + ahd_lock(ahd, &flags); + + found = ahd_reset_channel(ahd, scmd_channel(cmd) + 'A', + /*initiate reset*/TRUE); + ahd_unlock(ahd, &flags); + + if (bootverbose) + printk("%s: SCSI bus reset delivered. " + "%d SCBs aborted.\n", ahd_name(ahd), found); + + return (SUCCESS); +} + +struct scsi_host_template aic79xx_driver_template = { + .module = THIS_MODULE, + .name = "aic79xx", + .proc_name = "aic79xx", + .show_info = ahd_linux_show_info, + .write_info = ahd_proc_write_seeprom, + .info = ahd_linux_info, + .queuecommand = ahd_linux_queue, + .eh_abort_handler = ahd_linux_abort, + .eh_device_reset_handler = ahd_linux_dev_reset, + .eh_bus_reset_handler = ahd_linux_bus_reset, +#if defined(__i386__) + .bios_param = ahd_linux_biosparam, +#endif + .can_queue = AHD_MAX_QUEUE, + .this_id = -1, + .max_sectors = 8192, + .cmd_per_lun = 2, + .slave_alloc = ahd_linux_slave_alloc, + .slave_configure = ahd_linux_slave_configure, + .target_alloc = ahd_linux_target_alloc, + .target_destroy = ahd_linux_target_destroy, +}; + +/******************************** Bus DMA *************************************/ +int +ahd_dma_tag_create(struct ahd_softc *ahd, bus_dma_tag_t parent, + bus_size_t alignment, bus_size_t boundary, + dma_addr_t lowaddr, dma_addr_t highaddr, + bus_dma_filter_t *filter, void *filterarg, + bus_size_t maxsize, int nsegments, + bus_size_t maxsegsz, int flags, bus_dma_tag_t *ret_tag) +{ + bus_dma_tag_t dmat; + + dmat = kmalloc(sizeof(*dmat), GFP_ATOMIC); + if (dmat == NULL) + return (ENOMEM); + + /* + * Linux is very simplistic about DMA memory. For now don't + * maintain all specification information. Once Linux supplies + * better facilities for doing these operations, or the + * needs of this particular driver change, we might need to do + * more here. + */ + dmat->alignment = alignment; + dmat->boundary = boundary; + dmat->maxsize = maxsize; + *ret_tag = dmat; + return (0); +} + +void +ahd_dma_tag_destroy(struct ahd_softc *ahd, bus_dma_tag_t dmat) +{ + kfree(dmat); +} + +int +ahd_dmamem_alloc(struct ahd_softc *ahd, bus_dma_tag_t dmat, void** vaddr, + int flags, bus_dmamap_t *mapp) +{ + *vaddr = dma_alloc_coherent(&ahd->dev_softc->dev, dmat->maxsize, mapp, + GFP_ATOMIC); + if (*vaddr == NULL) + return (ENOMEM); + return(0); +} + +void +ahd_dmamem_free(struct ahd_softc *ahd, bus_dma_tag_t dmat, + void* vaddr, bus_dmamap_t map) +{ + dma_free_coherent(&ahd->dev_softc->dev, dmat->maxsize, vaddr, map); +} + +int +ahd_dmamap_load(struct ahd_softc *ahd, bus_dma_tag_t dmat, bus_dmamap_t map, + void *buf, bus_size_t buflen, bus_dmamap_callback_t *cb, + void *cb_arg, int flags) +{ + /* + * Assume for now that this will only be used during + * initialization and not for per-transaction buffer mapping. + */ + bus_dma_segment_t stack_sg; + + stack_sg.ds_addr = map; + stack_sg.ds_len = dmat->maxsize; + cb(cb_arg, &stack_sg, /*nseg*/1, /*error*/0); + return (0); +} + +void +ahd_dmamap_destroy(struct ahd_softc *ahd, bus_dma_tag_t dmat, bus_dmamap_t map) +{ +} + +int +ahd_dmamap_unload(struct ahd_softc *ahd, bus_dma_tag_t dmat, bus_dmamap_t map) +{ + /* Nothing to do */ + return (0); +} + +/********************* Platform Dependent Functions ***************************/ +static void +ahd_linux_setup_iocell_info(u_long index, int instance, int targ, int32_t value) +{ + + if ((instance >= 0) + && (instance < ARRAY_SIZE(aic79xx_iocell_info))) { + uint8_t *iocell_info; + + iocell_info = (uint8_t*)&aic79xx_iocell_info[instance]; + iocell_info[index] = value & 0xFFFF; + if (bootverbose) + printk("iocell[%d:%ld] = %d\n", instance, index, value); + } +} + +static void +ahd_linux_setup_tag_info_global(char *p) +{ + int tags, i, j; + + tags = simple_strtoul(p + 1, NULL, 0) & 0xff; + printk("Setting Global Tags= %d\n", tags); + + for (i = 0; i < ARRAY_SIZE(aic79xx_tag_info); i++) { + for (j = 0; j < AHD_NUM_TARGETS; j++) { + aic79xx_tag_info[i].tag_commands[j] = tags; + } + } +} + +static void +ahd_linux_setup_tag_info(u_long arg, int instance, int targ, int32_t value) +{ + + if ((instance >= 0) && (targ >= 0) + && (instance < ARRAY_SIZE(aic79xx_tag_info)) + && (targ < AHD_NUM_TARGETS)) { + aic79xx_tag_info[instance].tag_commands[targ] = value & 0x1FF; + if (bootverbose) + printk("tag_info[%d:%d] = %d\n", instance, targ, value); + } +} + +static char * +ahd_parse_brace_option(char *opt_name, char *opt_arg, char *end, int depth, + void (*callback)(u_long, int, int, int32_t), + u_long callback_arg) +{ + char *tok_end; + char *tok_end2; + int i; + int instance; + int targ; + int done; + char tok_list[] = {'.', ',', '{', '}', '\0'}; + + /* All options use a ':' name/arg separator */ + if (*opt_arg != ':') + return (opt_arg); + opt_arg++; + instance = -1; + targ = -1; + done = FALSE; + /* + * Restore separator that may be in + * the middle of our option argument. + */ + tok_end = strchr(opt_arg, '\0'); + if (tok_end < end) + *tok_end = ','; + while (!done) { + switch (*opt_arg) { + case '{': + if (instance == -1) { + instance = 0; + } else { + if (depth > 1) { + if (targ == -1) + targ = 0; + } else { + printk("Malformed Option %s\n", + opt_name); + done = TRUE; + } + } + opt_arg++; + break; + case '}': + if (targ != -1) + targ = -1; + else if (instance != -1) + instance = -1; + opt_arg++; + break; + case ',': + case '.': + if (instance == -1) + done = TRUE; + else if (targ >= 0) + targ++; + else if (instance >= 0) + instance++; + opt_arg++; + break; + case '\0': + done = TRUE; + break; + default: + tok_end = end; + for (i = 0; tok_list[i]; i++) { + tok_end2 = strchr(opt_arg, tok_list[i]); + if ((tok_end2) && (tok_end2 < tok_end)) + tok_end = tok_end2; + } + callback(callback_arg, instance, targ, + simple_strtol(opt_arg, NULL, 0)); + opt_arg = tok_end; + break; + } + } + return (opt_arg); +} + +/* + * Handle Linux boot parameters. This routine allows for assigning a value + * to a parameter with a ':' between the parameter and the value. + * ie. aic79xx=stpwlev:1,extended + */ +static int +aic79xx_setup(char *s) +{ + int i, n; + char *p; + char *end; + + static const struct { + const char *name; + uint32_t *flag; + } options[] = { + { "extended", &aic79xx_extended }, + { "no_reset", &aic79xx_no_reset }, + { "verbose", &aic79xx_verbose }, + { "allow_memio", &aic79xx_allow_memio}, +#ifdef AHD_DEBUG + { "debug", &ahd_debug }, +#endif + { "periodic_otag", &aic79xx_periodic_otag }, + { "pci_parity", &aic79xx_pci_parity }, + { "seltime", &aic79xx_seltime }, + { "tag_info", NULL }, + { "global_tag_depth", NULL}, + { "slewrate", NULL }, + { "precomp", NULL }, + { "amplitude", NULL }, + { "slowcrc", &aic79xx_slowcrc }, + }; + + end = strchr(s, '\0'); + + /* + * XXX ia64 gcc isn't smart enough to know that ARRAY_SIZE + * will never be 0 in this case. + */ + n = 0; + + while ((p = strsep(&s, ",.")) != NULL) { + if (*p == '\0') + continue; + for (i = 0; i < ARRAY_SIZE(options); i++) { + + n = strlen(options[i].name); + if (strncmp(options[i].name, p, n) == 0) + break; + } + if (i == ARRAY_SIZE(options)) + continue; + + if (strncmp(p, "global_tag_depth", n) == 0) { + ahd_linux_setup_tag_info_global(p + n); + } else if (strncmp(p, "tag_info", n) == 0) { + s = ahd_parse_brace_option("tag_info", p + n, end, + 2, ahd_linux_setup_tag_info, 0); + } else if (strncmp(p, "slewrate", n) == 0) { + s = ahd_parse_brace_option("slewrate", + p + n, end, 1, ahd_linux_setup_iocell_info, + AIC79XX_SLEWRATE_INDEX); + } else if (strncmp(p, "precomp", n) == 0) { + s = ahd_parse_brace_option("precomp", + p + n, end, 1, ahd_linux_setup_iocell_info, + AIC79XX_PRECOMP_INDEX); + } else if (strncmp(p, "amplitude", n) == 0) { + s = ahd_parse_brace_option("amplitude", + p + n, end, 1, ahd_linux_setup_iocell_info, + AIC79XX_AMPLITUDE_INDEX); + } else if (p[n] == ':') { + *(options[i].flag) = simple_strtoul(p + n + 1, NULL, 0); + } else if (!strncmp(p, "verbose", n)) { + *(options[i].flag) = 1; + } else { + *(options[i].flag) ^= 0xFFFFFFFF; + } + } + return 1; +} + +__setup("aic79xx=", aic79xx_setup); + +uint32_t aic79xx_verbose; + +int +ahd_linux_register_host(struct ahd_softc *ahd, struct scsi_host_template *template) +{ + char buf[80]; + struct Scsi_Host *host; + char *new_name; + u_long s; + int retval; + + template->name = ahd->description; + host = scsi_host_alloc(template, sizeof(struct ahd_softc *)); + if (host == NULL) + return (ENOMEM); + + *((struct ahd_softc **)host->hostdata) = ahd; + ahd->platform_data->host = host; + host->can_queue = AHD_MAX_QUEUE; + host->cmd_per_lun = 2; + host->sg_tablesize = AHD_NSEG; + host->this_id = ahd->our_id; + host->irq = ahd->platform_data->irq; + host->max_id = (ahd->features & AHD_WIDE) ? 16 : 8; + host->max_lun = AHD_NUM_LUNS; + host->max_channel = 0; + host->sg_tablesize = AHD_NSEG; + ahd_lock(ahd, &s); + ahd_set_unit(ahd, ahd_linux_unit++); + ahd_unlock(ahd, &s); + sprintf(buf, "scsi%d", host->host_no); + new_name = kmalloc(strlen(buf) + 1, GFP_ATOMIC); + if (new_name != NULL) { + strcpy(new_name, buf); + ahd_set_name(ahd, new_name); + } + host->unique_id = ahd->unit; + ahd_linux_initialize_scsi_bus(ahd); + ahd_intr_enable(ahd, TRUE); + + host->transportt = ahd_linux_transport_template; + + retval = scsi_add_host(host, &ahd->dev_softc->dev); + if (retval) { + printk(KERN_WARNING "aic79xx: scsi_add_host failed\n"); + scsi_host_put(host); + return retval; + } + + scsi_scan_host(host); + return 0; +} + +/* + * Place the SCSI bus into a known state by either resetting it, + * or forcing transfer negotiations on the next command to any + * target. + */ +static void +ahd_linux_initialize_scsi_bus(struct ahd_softc *ahd) +{ + u_int target_id; + u_int numtarg; + unsigned long s; + + target_id = 0; + numtarg = 0; + + if (aic79xx_no_reset != 0) + ahd->flags &= ~AHD_RESET_BUS_A; + + if ((ahd->flags & AHD_RESET_BUS_A) != 0) + ahd_reset_channel(ahd, 'A', /*initiate_reset*/TRUE); + else + numtarg = (ahd->features & AHD_WIDE) ? 16 : 8; + + ahd_lock(ahd, &s); + + /* + * Force negotiation to async for all targets that + * will not see an initial bus reset. + */ + for (; target_id < numtarg; target_id++) { + struct ahd_devinfo devinfo; + struct ahd_initiator_tinfo *tinfo; + struct ahd_tmode_tstate *tstate; + + tinfo = ahd_fetch_transinfo(ahd, 'A', ahd->our_id, + target_id, &tstate); + ahd_compile_devinfo(&devinfo, ahd->our_id, target_id, + CAM_LUN_WILDCARD, 'A', ROLE_INITIATOR); + ahd_update_neg_request(ahd, &devinfo, tstate, + tinfo, AHD_NEG_ALWAYS); + } + ahd_unlock(ahd, &s); + /* Give the bus some time to recover */ + if ((ahd->flags & AHD_RESET_BUS_A) != 0) { + ahd_freeze_simq(ahd); + msleep(AIC79XX_RESET_DELAY); + ahd_release_simq(ahd); + } +} + +int +ahd_platform_alloc(struct ahd_softc *ahd, void *platform_arg) +{ + ahd->platform_data = + kzalloc(sizeof(struct ahd_platform_data), GFP_ATOMIC); + if (ahd->platform_data == NULL) + return (ENOMEM); + ahd->platform_data->irq = AHD_LINUX_NOIRQ; + ahd_lockinit(ahd); + ahd->seltime = (aic79xx_seltime & 0x3) << 4; + return (0); +} + +void +ahd_platform_free(struct ahd_softc *ahd) +{ + struct scsi_target *starget; + int i; + + if (ahd->platform_data != NULL) { + /* destroy all of the device and target objects */ + for (i = 0; i < AHD_NUM_TARGETS; i++) { + starget = ahd->platform_data->starget[i]; + if (starget != NULL) { + ahd->platform_data->starget[i] = NULL; + } + } + + if (ahd->platform_data->irq != AHD_LINUX_NOIRQ) + free_irq(ahd->platform_data->irq, ahd); + if (ahd->tags[0] == BUS_SPACE_PIO + && ahd->bshs[0].ioport != 0) + release_region(ahd->bshs[0].ioport, 256); + if (ahd->tags[1] == BUS_SPACE_PIO + && ahd->bshs[1].ioport != 0) + release_region(ahd->bshs[1].ioport, 256); + if (ahd->tags[0] == BUS_SPACE_MEMIO + && ahd->bshs[0].maddr != NULL) { + iounmap(ahd->bshs[0].maddr); + release_mem_region(ahd->platform_data->mem_busaddr, + 0x1000); + } + if (ahd->platform_data->host) + scsi_host_put(ahd->platform_data->host); + + kfree(ahd->platform_data); + } +} + +void +ahd_platform_init(struct ahd_softc *ahd) +{ + /* + * Lookup and commit any modified IO Cell options. + */ + if (ahd->unit < ARRAY_SIZE(aic79xx_iocell_info)) { + const struct ahd_linux_iocell_opts *iocell_opts; + + iocell_opts = &aic79xx_iocell_info[ahd->unit]; + if (iocell_opts->precomp != AIC79XX_DEFAULT_PRECOMP) + AHD_SET_PRECOMP(ahd, iocell_opts->precomp); + if (iocell_opts->slewrate != AIC79XX_DEFAULT_SLEWRATE) + AHD_SET_SLEWRATE(ahd, iocell_opts->slewrate); + if (iocell_opts->amplitude != AIC79XX_DEFAULT_AMPLITUDE) + AHD_SET_AMPLITUDE(ahd, iocell_opts->amplitude); + } + +} + +void +ahd_platform_freeze_devq(struct ahd_softc *ahd, struct scb *scb) +{ + ahd_platform_abort_scbs(ahd, SCB_GET_TARGET(ahd, scb), + SCB_GET_CHANNEL(ahd, scb), + SCB_GET_LUN(scb), SCB_LIST_NULL, + ROLE_UNKNOWN, CAM_REQUEUE_REQ); +} + +void +ahd_platform_set_tags(struct ahd_softc *ahd, struct scsi_device *sdev, + struct ahd_devinfo *devinfo, ahd_queue_alg alg) +{ + struct ahd_linux_device *dev; + int was_queuing; + int now_queuing; + + if (sdev == NULL) + return; + + dev = scsi_transport_device_data(sdev); + + if (dev == NULL) + return; + was_queuing = dev->flags & (AHD_DEV_Q_BASIC|AHD_DEV_Q_TAGGED); + switch (alg) { + default: + case AHD_QUEUE_NONE: + now_queuing = 0; + break; + case AHD_QUEUE_BASIC: + now_queuing = AHD_DEV_Q_BASIC; + break; + case AHD_QUEUE_TAGGED: + now_queuing = AHD_DEV_Q_TAGGED; + break; + } + if ((dev->flags & AHD_DEV_FREEZE_TIL_EMPTY) == 0 + && (was_queuing != now_queuing) + && (dev->active != 0)) { + dev->flags |= AHD_DEV_FREEZE_TIL_EMPTY; + dev->qfrozen++; + } + + dev->flags &= ~(AHD_DEV_Q_BASIC|AHD_DEV_Q_TAGGED|AHD_DEV_PERIODIC_OTAG); + if (now_queuing) { + u_int usertags; + + usertags = ahd_linux_user_tagdepth(ahd, devinfo); + if (!was_queuing) { + /* + * Start out aggressively and allow our + * dynamic queue depth algorithm to take + * care of the rest. + */ + dev->maxtags = usertags; + dev->openings = dev->maxtags - dev->active; + } + if (dev->maxtags == 0) { + /* + * Queueing is disabled by the user. + */ + dev->openings = 1; + } else if (alg == AHD_QUEUE_TAGGED) { + dev->flags |= AHD_DEV_Q_TAGGED; + if (aic79xx_periodic_otag != 0) + dev->flags |= AHD_DEV_PERIODIC_OTAG; + } else + dev->flags |= AHD_DEV_Q_BASIC; + } else { + /* We can only have one opening. */ + dev->maxtags = 0; + dev->openings = 1 - dev->active; + } + + switch ((dev->flags & (AHD_DEV_Q_BASIC|AHD_DEV_Q_TAGGED))) { + case AHD_DEV_Q_BASIC: + case AHD_DEV_Q_TAGGED: + scsi_change_queue_depth(sdev, + dev->openings + dev->active); + break; + default: + /* + * We allow the OS to queue 2 untagged transactions to + * us at any time even though we can only execute them + * serially on the controller/device. This should + * remove some latency. + */ + scsi_change_queue_depth(sdev, 1); + break; + } +} + +int +ahd_platform_abort_scbs(struct ahd_softc *ahd, int target, char channel, + int lun, u_int tag, role_t role, uint32_t status) +{ + return 0; +} + +static u_int +ahd_linux_user_tagdepth(struct ahd_softc *ahd, struct ahd_devinfo *devinfo) +{ + static int warned_user; + u_int tags; + + tags = 0; + if ((ahd->user_discenable & devinfo->target_mask) != 0) { + if (ahd->unit >= ARRAY_SIZE(aic79xx_tag_info)) { + + if (warned_user == 0) { + printk(KERN_WARNING +"aic79xx: WARNING: Insufficient tag_info instances\n" +"aic79xx: for installed controllers. Using defaults\n" +"aic79xx: Please update the aic79xx_tag_info array in\n" +"aic79xx: the aic79xx_osm.c source file.\n"); + warned_user++; + } + tags = AHD_MAX_QUEUE; + } else { + adapter_tag_info_t *tag_info; + + tag_info = &aic79xx_tag_info[ahd->unit]; + tags = tag_info->tag_commands[devinfo->target_offset]; + if (tags > AHD_MAX_QUEUE) + tags = AHD_MAX_QUEUE; + } + } + return (tags); +} + +/* + * Determines the queue depth for a given device. + */ +static void +ahd_linux_device_queue_depth(struct scsi_device *sdev) +{ + struct ahd_devinfo devinfo; + u_int tags; + struct ahd_softc *ahd = *((struct ahd_softc **)sdev->host->hostdata); + + ahd_compile_devinfo(&devinfo, + ahd->our_id, + sdev->sdev_target->id, sdev->lun, + sdev->sdev_target->channel == 0 ? 'A' : 'B', + ROLE_INITIATOR); + tags = ahd_linux_user_tagdepth(ahd, &devinfo); + if (tags != 0 && sdev->tagged_supported != 0) { + + ahd_platform_set_tags(ahd, sdev, &devinfo, AHD_QUEUE_TAGGED); + ahd_send_async(ahd, devinfo.channel, devinfo.target, + devinfo.lun, AC_TRANSFER_NEG); + ahd_print_devinfo(ahd, &devinfo); + printk("Tagged Queuing enabled. Depth %d\n", tags); + } else { + ahd_platform_set_tags(ahd, sdev, &devinfo, AHD_QUEUE_NONE); + ahd_send_async(ahd, devinfo.channel, devinfo.target, + devinfo.lun, AC_TRANSFER_NEG); + } +} + +static int +ahd_linux_run_command(struct ahd_softc *ahd, struct ahd_linux_device *dev, + struct scsi_cmnd *cmd) +{ + struct scb *scb; + struct hardware_scb *hscb; + struct ahd_initiator_tinfo *tinfo; + struct ahd_tmode_tstate *tstate; + u_int col_idx; + uint16_t mask; + unsigned long flags; + int nseg; + + nseg = scsi_dma_map(cmd); + if (nseg < 0) + return SCSI_MLQUEUE_HOST_BUSY; + + ahd_lock(ahd, &flags); + + /* + * Get an scb to use. + */ + tinfo = ahd_fetch_transinfo(ahd, 'A', ahd->our_id, + cmd->device->id, &tstate); + if ((dev->flags & (AHD_DEV_Q_TAGGED|AHD_DEV_Q_BASIC)) == 0 + || (tinfo->curr.ppr_options & MSG_EXT_PPR_IU_REQ) != 0) { + col_idx = AHD_NEVER_COL_IDX; + } else { + col_idx = AHD_BUILD_COL_IDX(cmd->device->id, + cmd->device->lun); + } + if ((scb = ahd_get_scb(ahd, col_idx)) == NULL) { + ahd->flags |= AHD_RESOURCE_SHORTAGE; + ahd_unlock(ahd, &flags); + scsi_dma_unmap(cmd); + return SCSI_MLQUEUE_HOST_BUSY; + } + + scb->io_ctx = cmd; + scb->platform_data->dev = dev; + hscb = scb->hscb; + cmd->host_scribble = (char *)scb; + + /* + * Fill out basics of the HSCB. + */ + hscb->control = 0; + hscb->scsiid = BUILD_SCSIID(ahd, cmd); + hscb->lun = cmd->device->lun; + scb->hscb->task_management = 0; + mask = SCB_GET_TARGET_MASK(ahd, scb); + + if ((ahd->user_discenable & mask) != 0) + hscb->control |= DISCENB; + + if ((tinfo->curr.ppr_options & MSG_EXT_PPR_IU_REQ) != 0) + scb->flags |= SCB_PACKETIZED; + + if ((tstate->auto_negotiate & mask) != 0) { + scb->flags |= SCB_AUTO_NEGOTIATE; + scb->hscb->control |= MK_MESSAGE; + } + + if ((dev->flags & (AHD_DEV_Q_TAGGED|AHD_DEV_Q_BASIC)) != 0) { + if (dev->commands_since_idle_or_otag == AHD_OTAG_THRESH + && (dev->flags & AHD_DEV_Q_TAGGED) != 0) { + hscb->control |= MSG_ORDERED_TASK; + dev->commands_since_idle_or_otag = 0; + } else { + hscb->control |= MSG_SIMPLE_TASK; + } + } + + hscb->cdb_len = cmd->cmd_len; + memcpy(hscb->shared_data.idata.cdb, cmd->cmnd, hscb->cdb_len); + + scb->platform_data->xfer_len = 0; + ahd_set_residual(scb, 0); + ahd_set_sense_residual(scb, 0); + scb->sg_count = 0; + + if (nseg > 0) { + void *sg = scb->sg_list; + struct scatterlist *cur_seg; + int i; + + scb->platform_data->xfer_len = 0; + + scsi_for_each_sg(cmd, cur_seg, nseg, i) { + dma_addr_t addr; + bus_size_t len; + + addr = sg_dma_address(cur_seg); + len = sg_dma_len(cur_seg); + scb->platform_data->xfer_len += len; + sg = ahd_sg_setup(ahd, scb, sg, addr, len, + i == (nseg - 1)); + } + } + + LIST_INSERT_HEAD(&ahd->pending_scbs, scb, pending_links); + dev->openings--; + dev->active++; + dev->commands_issued++; + + if ((dev->flags & AHD_DEV_PERIODIC_OTAG) != 0) + dev->commands_since_idle_or_otag++; + scb->flags |= SCB_ACTIVE; + ahd_queue_scb(ahd, scb); + + ahd_unlock(ahd, &flags); + + return 0; +} + +/* + * SCSI controller interrupt handler. + */ +irqreturn_t +ahd_linux_isr(int irq, void *dev_id) +{ + struct ahd_softc *ahd; + u_long flags; + int ours; + + ahd = (struct ahd_softc *) dev_id; + ahd_lock(ahd, &flags); + ours = ahd_intr(ahd); + ahd_unlock(ahd, &flags); + return IRQ_RETVAL(ours); +} + +void +ahd_send_async(struct ahd_softc *ahd, char channel, + u_int target, u_int lun, ac_code code) +{ + switch (code) { + case AC_TRANSFER_NEG: + { + struct scsi_target *starget; + struct ahd_initiator_tinfo *tinfo; + struct ahd_tmode_tstate *tstate; + unsigned int target_ppr_options; + + BUG_ON(target == CAM_TARGET_WILDCARD); + + tinfo = ahd_fetch_transinfo(ahd, channel, ahd->our_id, + target, &tstate); + + /* + * Don't bother reporting results while + * negotiations are still pending. + */ + if (tinfo->curr.period != tinfo->goal.period + || tinfo->curr.width != tinfo->goal.width + || tinfo->curr.offset != tinfo->goal.offset + || tinfo->curr.ppr_options != tinfo->goal.ppr_options) + if (bootverbose == 0) + break; + + /* + * Don't bother reporting results that + * are identical to those last reported. + */ + starget = ahd->platform_data->starget[target]; + if (starget == NULL) + break; + + target_ppr_options = + (spi_dt(starget) ? MSG_EXT_PPR_DT_REQ : 0) + + (spi_qas(starget) ? MSG_EXT_PPR_QAS_REQ : 0) + + (spi_iu(starget) ? MSG_EXT_PPR_IU_REQ : 0) + + (spi_rd_strm(starget) ? MSG_EXT_PPR_RD_STRM : 0) + + (spi_pcomp_en(starget) ? MSG_EXT_PPR_PCOMP_EN : 0) + + (spi_rti(starget) ? MSG_EXT_PPR_RTI : 0) + + (spi_wr_flow(starget) ? MSG_EXT_PPR_WR_FLOW : 0) + + (spi_hold_mcs(starget) ? MSG_EXT_PPR_HOLD_MCS : 0); + + if (tinfo->curr.period == spi_period(starget) + && tinfo->curr.width == spi_width(starget) + && tinfo->curr.offset == spi_offset(starget) + && tinfo->curr.ppr_options == target_ppr_options) + if (bootverbose == 0) + break; + + spi_period(starget) = tinfo->curr.period; + spi_width(starget) = tinfo->curr.width; + spi_offset(starget) = tinfo->curr.offset; + spi_dt(starget) = tinfo->curr.ppr_options & MSG_EXT_PPR_DT_REQ ? 1 : 0; + spi_qas(starget) = tinfo->curr.ppr_options & MSG_EXT_PPR_QAS_REQ ? 1 : 0; + spi_iu(starget) = tinfo->curr.ppr_options & MSG_EXT_PPR_IU_REQ ? 1 : 0; + spi_rd_strm(starget) = tinfo->curr.ppr_options & MSG_EXT_PPR_RD_STRM ? 1 : 0; + spi_pcomp_en(starget) = tinfo->curr.ppr_options & MSG_EXT_PPR_PCOMP_EN ? 1 : 0; + spi_rti(starget) = tinfo->curr.ppr_options & MSG_EXT_PPR_RTI ? 1 : 0; + spi_wr_flow(starget) = tinfo->curr.ppr_options & MSG_EXT_PPR_WR_FLOW ? 1 : 0; + spi_hold_mcs(starget) = tinfo->curr.ppr_options & MSG_EXT_PPR_HOLD_MCS ? 1 : 0; + spi_display_xfer_agreement(starget); + break; + } + case AC_SENT_BDR: + { + WARN_ON(lun != CAM_LUN_WILDCARD); + scsi_report_device_reset(ahd->platform_data->host, + channel - 'A', target); + break; + } + case AC_BUS_RESET: + if (ahd->platform_data->host != NULL) { + scsi_report_bus_reset(ahd->platform_data->host, + channel - 'A'); + } + break; + default: + panic("ahd_send_async: Unexpected async event"); + } +} + +/* + * Calls the higher level scsi done function and frees the scb. + */ +void +ahd_done(struct ahd_softc *ahd, struct scb *scb) +{ + struct scsi_cmnd *cmd; + struct ahd_linux_device *dev; + + if ((scb->flags & SCB_ACTIVE) == 0) { + printk("SCB %d done'd twice\n", SCB_GET_TAG(scb)); + ahd_dump_card_state(ahd); + panic("Stopping for safety"); + } + LIST_REMOVE(scb, pending_links); + cmd = scb->io_ctx; + dev = scb->platform_data->dev; + dev->active--; + dev->openings++; + if ((cmd->result & (CAM_DEV_QFRZN << 16)) != 0) { + cmd->result &= ~(CAM_DEV_QFRZN << 16); + dev->qfrozen--; + } + ahd_linux_unmap_scb(ahd, scb); + + /* + * Guard against stale sense data. + * The Linux mid-layer assumes that sense + * was retrieved anytime the first byte of + * the sense buffer looks "sane". + */ + cmd->sense_buffer[0] = 0; + if (ahd_get_transaction_status(scb) == CAM_REQ_INPROG) { +#ifdef AHD_REPORT_UNDERFLOWS + uint32_t amount_xferred; + + amount_xferred = + ahd_get_transfer_length(scb) - ahd_get_residual(scb); +#endif + if ((scb->flags & SCB_TRANSMISSION_ERROR) != 0) { +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_MISC) != 0) { + ahd_print_path(ahd, scb); + printk("Set CAM_UNCOR_PARITY\n"); + } +#endif + ahd_set_transaction_status(scb, CAM_UNCOR_PARITY); +#ifdef AHD_REPORT_UNDERFLOWS + /* + * This code is disabled by default as some + * clients of the SCSI system do not properly + * initialize the underflow parameter. This + * results in spurious termination of commands + * that complete as expected (e.g. underflow is + * allowed as command can return variable amounts + * of data. + */ + } else if (amount_xferred < scb->io_ctx->underflow) { + u_int i; + + ahd_print_path(ahd, scb); + printk("CDB:"); + for (i = 0; i < scb->io_ctx->cmd_len; i++) + printk(" 0x%x", scb->io_ctx->cmnd[i]); + printk("\n"); + ahd_print_path(ahd, scb); + printk("Saw underflow (%ld of %ld bytes). " + "Treated as error\n", + ahd_get_residual(scb), + ahd_get_transfer_length(scb)); + ahd_set_transaction_status(scb, CAM_DATA_RUN_ERR); +#endif + } else { + ahd_set_transaction_status(scb, CAM_REQ_CMP); + } + } else if (ahd_get_transaction_status(scb) == CAM_SCSI_STATUS_ERROR) { + ahd_linux_handle_scsi_status(ahd, cmd->device, scb); + } + + if (dev->openings == 1 + && ahd_get_transaction_status(scb) == CAM_REQ_CMP + && ahd_get_scsi_status(scb) != SCSI_STATUS_QUEUE_FULL) + dev->tag_success_count++; + /* + * Some devices deal with temporary internal resource + * shortages by returning queue full. When the queue + * full occurrs, we throttle back. Slowly try to get + * back to our previous queue depth. + */ + if ((dev->openings + dev->active) < dev->maxtags + && dev->tag_success_count > AHD_TAG_SUCCESS_INTERVAL) { + dev->tag_success_count = 0; + dev->openings++; + } + + if (dev->active == 0) + dev->commands_since_idle_or_otag = 0; + + if ((scb->flags & SCB_RECOVERY_SCB) != 0) { + printk("Recovery SCB completes\n"); + if (ahd_get_transaction_status(scb) == CAM_BDR_SENT + || ahd_get_transaction_status(scb) == CAM_REQ_ABORTED) + ahd_set_transaction_status(scb, CAM_CMD_TIMEOUT); + + if (ahd->platform_data->eh_done) + complete(ahd->platform_data->eh_done); + } + + ahd_free_scb(ahd, scb); + ahd_linux_queue_cmd_complete(ahd, cmd); +} + +static void +ahd_linux_handle_scsi_status(struct ahd_softc *ahd, + struct scsi_device *sdev, struct scb *scb) +{ + struct ahd_devinfo devinfo; + struct ahd_linux_device *dev = scsi_transport_device_data(sdev); + + ahd_compile_devinfo(&devinfo, + ahd->our_id, + sdev->sdev_target->id, sdev->lun, + sdev->sdev_target->channel == 0 ? 'A' : 'B', + ROLE_INITIATOR); + + /* + * We don't currently trust the mid-layer to + * properly deal with queue full or busy. So, + * when one occurs, we tell the mid-layer to + * unconditionally requeue the command to us + * so that we can retry it ourselves. We also + * implement our own throttling mechanism so + * we don't clobber the device with too many + * commands. + */ + switch (ahd_get_scsi_status(scb)) { + default: + break; + case SCSI_STATUS_CHECK_COND: + case SCSI_STATUS_CMD_TERMINATED: + { + struct scsi_cmnd *cmd; + + /* + * Copy sense information to the OS's cmd + * structure if it is available. + */ + cmd = scb->io_ctx; + if ((scb->flags & (SCB_SENSE|SCB_PKT_SENSE)) != 0) { + struct scsi_status_iu_header *siu; + u_int sense_size; + u_int sense_offset; + + if (scb->flags & SCB_SENSE) { + sense_size = min(sizeof(struct scsi_sense_data) + - ahd_get_sense_residual(scb), + (u_long)SCSI_SENSE_BUFFERSIZE); + sense_offset = 0; + } else { + /* + * Copy only the sense data into the provided + * buffer. + */ + siu = (struct scsi_status_iu_header *) + scb->sense_data; + sense_size = min_t(size_t, + scsi_4btoul(siu->sense_length), + SCSI_SENSE_BUFFERSIZE); + sense_offset = SIU_SENSE_OFFSET(siu); + } + + memset(cmd->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE); + memcpy(cmd->sense_buffer, + ahd_get_sense_buf(ahd, scb) + + sense_offset, sense_size); + cmd->result |= (DRIVER_SENSE << 24); + +#ifdef AHD_DEBUG + if (ahd_debug & AHD_SHOW_SENSE) { + int i; + + printk("Copied %d bytes of sense data at %d:", + sense_size, sense_offset); + for (i = 0; i < sense_size; i++) { + if ((i & 0xF) == 0) + printk("\n"); + printk("0x%x ", cmd->sense_buffer[i]); + } + printk("\n"); + } +#endif + } + break; + } + case SCSI_STATUS_QUEUE_FULL: + /* + * By the time the core driver has returned this + * command, all other commands that were queued + * to us but not the device have been returned. + * This ensures that dev->active is equal to + * the number of commands actually queued to + * the device. + */ + dev->tag_success_count = 0; + if (dev->active != 0) { + /* + * Drop our opening count to the number + * of commands currently outstanding. + */ + dev->openings = 0; +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_QFULL) != 0) { + ahd_print_path(ahd, scb); + printk("Dropping tag count to %d\n", + dev->active); + } +#endif + if (dev->active == dev->tags_on_last_queuefull) { + + dev->last_queuefull_same_count++; + /* + * If we repeatedly see a queue full + * at the same queue depth, this + * device has a fixed number of tag + * slots. Lock in this tag depth + * so we stop seeing queue fulls from + * this device. + */ + if (dev->last_queuefull_same_count + == AHD_LOCK_TAGS_COUNT) { + dev->maxtags = dev->active; + ahd_print_path(ahd, scb); + printk("Locking max tag count at %d\n", + dev->active); + } + } else { + dev->tags_on_last_queuefull = dev->active; + dev->last_queuefull_same_count = 0; + } + ahd_set_transaction_status(scb, CAM_REQUEUE_REQ); + ahd_set_scsi_status(scb, SCSI_STATUS_OK); + ahd_platform_set_tags(ahd, sdev, &devinfo, + (dev->flags & AHD_DEV_Q_BASIC) + ? AHD_QUEUE_BASIC : AHD_QUEUE_TAGGED); + break; + } + /* + * Drop down to a single opening, and treat this + * as if the target returned BUSY SCSI status. + */ + dev->openings = 1; + ahd_platform_set_tags(ahd, sdev, &devinfo, + (dev->flags & AHD_DEV_Q_BASIC) + ? AHD_QUEUE_BASIC : AHD_QUEUE_TAGGED); + ahd_set_scsi_status(scb, SCSI_STATUS_BUSY); + } +} + +static void +ahd_linux_queue_cmd_complete(struct ahd_softc *ahd, struct scsi_cmnd *cmd) +{ + int status; + int new_status = DID_OK; + int do_fallback = 0; + int scsi_status; + + /* + * Map CAM error codes into Linux Error codes. We + * avoid the conversion so that the DV code has the + * full error information available when making + * state change decisions. + */ + + status = ahd_cmd_get_transaction_status(cmd); + switch (status) { + case CAM_REQ_INPROG: + case CAM_REQ_CMP: + new_status = DID_OK; + break; + case CAM_AUTOSENSE_FAIL: + new_status = DID_ERROR; + fallthrough; + case CAM_SCSI_STATUS_ERROR: + scsi_status = ahd_cmd_get_scsi_status(cmd); + + switch(scsi_status) { + case SCSI_STATUS_CMD_TERMINATED: + case SCSI_STATUS_CHECK_COND: + if ((cmd->result >> 24) != DRIVER_SENSE) { + do_fallback = 1; + } else { + struct scsi_sense_data *sense; + + sense = (struct scsi_sense_data *) + cmd->sense_buffer; + if (sense->extra_len >= 5 && + (sense->add_sense_code == 0x47 + || sense->add_sense_code == 0x48)) + do_fallback = 1; + } + break; + default: + break; + } + break; + case CAM_REQ_ABORTED: + new_status = DID_ABORT; + break; + case CAM_BUSY: + new_status = DID_BUS_BUSY; + break; + case CAM_REQ_INVALID: + case CAM_PATH_INVALID: + new_status = DID_BAD_TARGET; + break; + case CAM_SEL_TIMEOUT: + new_status = DID_NO_CONNECT; + break; + case CAM_SCSI_BUS_RESET: + case CAM_BDR_SENT: + new_status = DID_RESET; + break; + case CAM_UNCOR_PARITY: + new_status = DID_PARITY; + do_fallback = 1; + break; + case CAM_CMD_TIMEOUT: + new_status = DID_TIME_OUT; + do_fallback = 1; + break; + case CAM_REQ_CMP_ERR: + case CAM_UNEXP_BUSFREE: + case CAM_DATA_RUN_ERR: + new_status = DID_ERROR; + do_fallback = 1; + break; + case CAM_UA_ABORT: + case CAM_NO_HBA: + case CAM_SEQUENCE_FAIL: + case CAM_CCB_LEN_ERR: + case CAM_PROVIDE_FAIL: + case CAM_REQ_TERMIO: + case CAM_UNREC_HBA_ERROR: + case CAM_REQ_TOO_BIG: + new_status = DID_ERROR; + break; + case CAM_REQUEUE_REQ: + new_status = DID_REQUEUE; + break; + default: + /* We should never get here */ + new_status = DID_ERROR; + break; + } + + if (do_fallback) { + printk("%s: device overrun (status %x) on %d:%d:%d\n", + ahd_name(ahd), status, cmd->device->channel, + cmd->device->id, (u8)cmd->device->lun); + } + + ahd_cmd_set_transaction_status(cmd, new_status); + + cmd->scsi_done(cmd); +} + +static void +ahd_freeze_simq(struct ahd_softc *ahd) +{ + scsi_block_requests(ahd->platform_data->host); +} + +static void +ahd_release_simq(struct ahd_softc *ahd) +{ + scsi_unblock_requests(ahd->platform_data->host); +} + +static int +ahd_linux_queue_abort_cmd(struct scsi_cmnd *cmd) +{ + struct ahd_softc *ahd; + struct ahd_linux_device *dev; + struct scb *pending_scb; + u_int saved_scbptr; + u_int active_scbptr; + u_int last_phase; + u_int saved_scsiid; + u_int cdb_byte; + int retval = SUCCESS; + int was_paused; + int paused; + int wait; + int disconnected; + ahd_mode_state saved_modes; + unsigned long flags; + + pending_scb = NULL; + paused = FALSE; + wait = FALSE; + ahd = *(struct ahd_softc **)cmd->device->host->hostdata; + + scmd_printk(KERN_INFO, cmd, + "Attempting to queue an ABORT message:"); + + printk("CDB:"); + for (cdb_byte = 0; cdb_byte < cmd->cmd_len; cdb_byte++) + printk(" 0x%x", cmd->cmnd[cdb_byte]); + printk("\n"); + + ahd_lock(ahd, &flags); + + /* + * First determine if we currently own this command. + * Start by searching the device queue. If not found + * there, check the pending_scb list. If not found + * at all, and the system wanted us to just abort the + * command, return success. + */ + dev = scsi_transport_device_data(cmd->device); + + if (dev == NULL) { + /* + * No target device for this command exists, + * so we must not still own the command. + */ + scmd_printk(KERN_INFO, cmd, "Is not an active device\n"); + goto done; + } + + /* + * See if we can find a matching cmd in the pending list. + */ + LIST_FOREACH(pending_scb, &ahd->pending_scbs, pending_links) { + if (pending_scb->io_ctx == cmd) + break; + } + + if (pending_scb == NULL) { + scmd_printk(KERN_INFO, cmd, "Command not found\n"); + goto done; + } + + if ((pending_scb->flags & SCB_RECOVERY_SCB) != 0) { + /* + * We can't queue two recovery actions using the same SCB + */ + retval = FAILED; + goto done; + } + + /* + * Ensure that the card doesn't do anything + * behind our back. Also make sure that we + * didn't "just" miss an interrupt that would + * affect this cmd. + */ + was_paused = ahd_is_paused(ahd); + ahd_pause_and_flushwork(ahd); + paused = TRUE; + + if ((pending_scb->flags & SCB_ACTIVE) == 0) { + scmd_printk(KERN_INFO, cmd, "Command already completed\n"); + goto done; + } + + printk("%s: At time of recovery, card was %spaused\n", + ahd_name(ahd), was_paused ? "" : "not "); + ahd_dump_card_state(ahd); + + disconnected = TRUE; + if (ahd_search_qinfifo(ahd, cmd->device->id, + cmd->device->channel + 'A', + cmd->device->lun, + pending_scb->hscb->tag, + ROLE_INITIATOR, CAM_REQ_ABORTED, + SEARCH_COMPLETE) > 0) { + printk("%s:%d:%d:%d: Cmd aborted from QINFIFO\n", + ahd_name(ahd), cmd->device->channel, + cmd->device->id, (u8)cmd->device->lun); + goto done; + } + + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + last_phase = ahd_inb(ahd, LASTPHASE); + saved_scbptr = ahd_get_scbptr(ahd); + active_scbptr = saved_scbptr; + if (disconnected && (ahd_inb(ahd, SEQ_FLAGS) & NOT_IDENTIFIED) == 0) { + struct scb *bus_scb; + + bus_scb = ahd_lookup_scb(ahd, active_scbptr); + if (bus_scb == pending_scb) + disconnected = FALSE; + } + + /* + * At this point, pending_scb is the scb associated with the + * passed in command. That command is currently active on the + * bus or is in the disconnected state. + */ + saved_scsiid = ahd_inb(ahd, SAVED_SCSIID); + if (last_phase != P_BUSFREE + && SCB_GET_TAG(pending_scb) == active_scbptr) { + + /* + * We're active on the bus, so assert ATN + * and hope that the target responds. + */ + pending_scb = ahd_lookup_scb(ahd, active_scbptr); + pending_scb->flags |= SCB_RECOVERY_SCB|SCB_ABORT; + ahd_outb(ahd, MSG_OUT, HOST_MSG); + ahd_outb(ahd, SCSISIGO, last_phase|ATNO); + scmd_printk(KERN_INFO, cmd, "Device is active, asserting ATN\n"); + wait = TRUE; + } else if (disconnected) { + + /* + * Actually re-queue this SCB in an attempt + * to select the device before it reconnects. + */ + pending_scb->flags |= SCB_RECOVERY_SCB|SCB_ABORT; + ahd_set_scbptr(ahd, SCB_GET_TAG(pending_scb)); + pending_scb->hscb->cdb_len = 0; + pending_scb->hscb->task_attribute = 0; + pending_scb->hscb->task_management = SIU_TASKMGMT_ABORT_TASK; + + if ((pending_scb->flags & SCB_PACKETIZED) != 0) { + /* + * Mark the SCB has having an outstanding + * task management function. Should the command + * complete normally before the task management + * function can be sent, the host will be notified + * to abort our requeued SCB. + */ + ahd_outb(ahd, SCB_TASK_MANAGEMENT, + pending_scb->hscb->task_management); + } else { + /* + * If non-packetized, set the MK_MESSAGE control + * bit indicating that we desire to send a message. + * We also set the disconnected flag since there is + * no guarantee that our SCB control byte matches + * the version on the card. We don't want the + * sequencer to abort the command thinking an + * unsolicited reselection occurred. + */ + pending_scb->hscb->control |= MK_MESSAGE|DISCONNECTED; + + /* + * The sequencer will never re-reference the + * in-core SCB. To make sure we are notified + * during reselection, set the MK_MESSAGE flag in + * the card's copy of the SCB. + */ + ahd_outb(ahd, SCB_CONTROL, + ahd_inb(ahd, SCB_CONTROL)|MK_MESSAGE); + } + + /* + * Clear out any entries in the QINFIFO first + * so we are the next SCB for this target + * to run. + */ + ahd_search_qinfifo(ahd, cmd->device->id, + cmd->device->channel + 'A', cmd->device->lun, + SCB_LIST_NULL, ROLE_INITIATOR, + CAM_REQUEUE_REQ, SEARCH_COMPLETE); + ahd_qinfifo_requeue_tail(ahd, pending_scb); + ahd_set_scbptr(ahd, saved_scbptr); + ahd_print_path(ahd, pending_scb); + printk("Device is disconnected, re-queuing SCB\n"); + wait = TRUE; + } else { + scmd_printk(KERN_INFO, cmd, "Unable to deliver message\n"); + retval = FAILED; + } + + + ahd_restore_modes(ahd, saved_modes); +done: + if (paused) + ahd_unpause(ahd); + if (wait) { + DECLARE_COMPLETION_ONSTACK(done); + + ahd->platform_data->eh_done = &done; + ahd_unlock(ahd, &flags); + + printk("%s: Recovery code sleeping\n", ahd_name(ahd)); + if (!wait_for_completion_timeout(&done, 5 * HZ)) { + ahd_lock(ahd, &flags); + ahd->platform_data->eh_done = NULL; + ahd_unlock(ahd, &flags); + printk("%s: Timer Expired (active %d)\n", + ahd_name(ahd), dev->active); + retval = FAILED; + } + printk("Recovery code awake\n"); + } else + ahd_unlock(ahd, &flags); + + if (retval != SUCCESS) + printk("%s: Command abort returning 0x%x\n", + ahd_name(ahd), retval); + + return retval; +} + +static void ahd_linux_set_width(struct scsi_target *starget, int width) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahd_softc *ahd = *((struct ahd_softc **)shost->hostdata); + struct ahd_devinfo devinfo; + unsigned long flags; + + ahd_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + ahd_lock(ahd, &flags); + ahd_set_width(ahd, &devinfo, width, AHD_TRANS_GOAL, FALSE); + ahd_unlock(ahd, &flags); +} + +static void ahd_linux_set_period(struct scsi_target *starget, int period) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahd_softc *ahd = *((struct ahd_softc **)shost->hostdata); + struct ahd_tmode_tstate *tstate; + struct ahd_initiator_tinfo *tinfo + = ahd_fetch_transinfo(ahd, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahd_devinfo devinfo; + unsigned int ppr_options = tinfo->goal.ppr_options; + unsigned int dt; + unsigned long flags; + unsigned long offset = tinfo->goal.offset; + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_DV) != 0) + printk("%s: set period to %d\n", ahd_name(ahd), period); +#endif + if (offset == 0) + offset = MAX_OFFSET; + + if (period < 8) + period = 8; + if (period < 10) { + if (spi_max_width(starget)) { + ppr_options |= MSG_EXT_PPR_DT_REQ; + if (period == 8) + ppr_options |= MSG_EXT_PPR_IU_REQ; + } else + period = 10; + } + + dt = ppr_options & MSG_EXT_PPR_DT_REQ; + + ahd_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + + /* all PPR requests apart from QAS require wide transfers */ + if (ppr_options & ~MSG_EXT_PPR_QAS_REQ) { + if (spi_width(starget) == 0) + ppr_options &= MSG_EXT_PPR_QAS_REQ; + } + + ahd_find_syncrate(ahd, &period, &ppr_options, + dt ? AHD_SYNCRATE_MAX : AHD_SYNCRATE_ULTRA2); + + ahd_lock(ahd, &flags); + ahd_set_syncrate(ahd, &devinfo, period, offset, + ppr_options, AHD_TRANS_GOAL, FALSE); + ahd_unlock(ahd, &flags); +} + +static void ahd_linux_set_offset(struct scsi_target *starget, int offset) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahd_softc *ahd = *((struct ahd_softc **)shost->hostdata); + struct ahd_tmode_tstate *tstate; + struct ahd_initiator_tinfo *tinfo + = ahd_fetch_transinfo(ahd, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahd_devinfo devinfo; + unsigned int ppr_options = 0; + unsigned int period = 0; + unsigned int dt = ppr_options & MSG_EXT_PPR_DT_REQ; + unsigned long flags; + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_DV) != 0) + printk("%s: set offset to %d\n", ahd_name(ahd), offset); +#endif + + ahd_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + if (offset != 0) { + period = tinfo->goal.period; + ppr_options = tinfo->goal.ppr_options; + ahd_find_syncrate(ahd, &period, &ppr_options, + dt ? AHD_SYNCRATE_MAX : AHD_SYNCRATE_ULTRA2); + } + + ahd_lock(ahd, &flags); + ahd_set_syncrate(ahd, &devinfo, period, offset, ppr_options, + AHD_TRANS_GOAL, FALSE); + ahd_unlock(ahd, &flags); +} + +static void ahd_linux_set_dt(struct scsi_target *starget, int dt) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahd_softc *ahd = *((struct ahd_softc **)shost->hostdata); + struct ahd_tmode_tstate *tstate; + struct ahd_initiator_tinfo *tinfo + = ahd_fetch_transinfo(ahd, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahd_devinfo devinfo; + unsigned int ppr_options = tinfo->goal.ppr_options + & ~MSG_EXT_PPR_DT_REQ; + unsigned int period = tinfo->goal.period; + unsigned int width = tinfo->goal.width; + unsigned long flags; + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_DV) != 0) + printk("%s: %s DT\n", ahd_name(ahd), + dt ? "enabling" : "disabling"); +#endif + if (dt && spi_max_width(starget)) { + ppr_options |= MSG_EXT_PPR_DT_REQ; + if (!width) + ahd_linux_set_width(starget, 1); + } else { + if (period <= 9) + period = 10; /* If resetting DT, period must be >= 25ns */ + /* IU is invalid without DT set */ + ppr_options &= ~MSG_EXT_PPR_IU_REQ; + } + ahd_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + ahd_find_syncrate(ahd, &period, &ppr_options, + dt ? AHD_SYNCRATE_MAX : AHD_SYNCRATE_ULTRA2); + + ahd_lock(ahd, &flags); + ahd_set_syncrate(ahd, &devinfo, period, tinfo->goal.offset, + ppr_options, AHD_TRANS_GOAL, FALSE); + ahd_unlock(ahd, &flags); +} + +static void ahd_linux_set_qas(struct scsi_target *starget, int qas) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahd_softc *ahd = *((struct ahd_softc **)shost->hostdata); + struct ahd_tmode_tstate *tstate; + struct ahd_initiator_tinfo *tinfo + = ahd_fetch_transinfo(ahd, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahd_devinfo devinfo; + unsigned int ppr_options = tinfo->goal.ppr_options + & ~MSG_EXT_PPR_QAS_REQ; + unsigned int period = tinfo->goal.period; + unsigned int dt; + unsigned long flags; + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_DV) != 0) + printk("%s: %s QAS\n", ahd_name(ahd), + qas ? "enabling" : "disabling"); +#endif + + if (qas) { + ppr_options |= MSG_EXT_PPR_QAS_REQ; + } + + dt = ppr_options & MSG_EXT_PPR_DT_REQ; + + ahd_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + ahd_find_syncrate(ahd, &period, &ppr_options, + dt ? AHD_SYNCRATE_MAX : AHD_SYNCRATE_ULTRA2); + + ahd_lock(ahd, &flags); + ahd_set_syncrate(ahd, &devinfo, period, tinfo->goal.offset, + ppr_options, AHD_TRANS_GOAL, FALSE); + ahd_unlock(ahd, &flags); +} + +static void ahd_linux_set_iu(struct scsi_target *starget, int iu) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahd_softc *ahd = *((struct ahd_softc **)shost->hostdata); + struct ahd_tmode_tstate *tstate; + struct ahd_initiator_tinfo *tinfo + = ahd_fetch_transinfo(ahd, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahd_devinfo devinfo; + unsigned int ppr_options = tinfo->goal.ppr_options + & ~MSG_EXT_PPR_IU_REQ; + unsigned int period = tinfo->goal.period; + unsigned int dt; + unsigned long flags; + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_DV) != 0) + printk("%s: %s IU\n", ahd_name(ahd), + iu ? "enabling" : "disabling"); +#endif + + if (iu && spi_max_width(starget)) { + ppr_options |= MSG_EXT_PPR_IU_REQ; + ppr_options |= MSG_EXT_PPR_DT_REQ; /* IU requires DT */ + } + + dt = ppr_options & MSG_EXT_PPR_DT_REQ; + + ahd_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + ahd_find_syncrate(ahd, &period, &ppr_options, + dt ? AHD_SYNCRATE_MAX : AHD_SYNCRATE_ULTRA2); + + ahd_lock(ahd, &flags); + ahd_set_syncrate(ahd, &devinfo, period, tinfo->goal.offset, + ppr_options, AHD_TRANS_GOAL, FALSE); + ahd_unlock(ahd, &flags); +} + +static void ahd_linux_set_rd_strm(struct scsi_target *starget, int rdstrm) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahd_softc *ahd = *((struct ahd_softc **)shost->hostdata); + struct ahd_tmode_tstate *tstate; + struct ahd_initiator_tinfo *tinfo + = ahd_fetch_transinfo(ahd, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahd_devinfo devinfo; + unsigned int ppr_options = tinfo->goal.ppr_options + & ~MSG_EXT_PPR_RD_STRM; + unsigned int period = tinfo->goal.period; + unsigned int dt = ppr_options & MSG_EXT_PPR_DT_REQ; + unsigned long flags; + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_DV) != 0) + printk("%s: %s Read Streaming\n", ahd_name(ahd), + rdstrm ? "enabling" : "disabling"); +#endif + + if (rdstrm && spi_max_width(starget)) + ppr_options |= MSG_EXT_PPR_RD_STRM; + + ahd_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + ahd_find_syncrate(ahd, &period, &ppr_options, + dt ? AHD_SYNCRATE_MAX : AHD_SYNCRATE_ULTRA2); + + ahd_lock(ahd, &flags); + ahd_set_syncrate(ahd, &devinfo, period, tinfo->goal.offset, + ppr_options, AHD_TRANS_GOAL, FALSE); + ahd_unlock(ahd, &flags); +} + +static void ahd_linux_set_wr_flow(struct scsi_target *starget, int wrflow) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahd_softc *ahd = *((struct ahd_softc **)shost->hostdata); + struct ahd_tmode_tstate *tstate; + struct ahd_initiator_tinfo *tinfo + = ahd_fetch_transinfo(ahd, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahd_devinfo devinfo; + unsigned int ppr_options = tinfo->goal.ppr_options + & ~MSG_EXT_PPR_WR_FLOW; + unsigned int period = tinfo->goal.period; + unsigned int dt = ppr_options & MSG_EXT_PPR_DT_REQ; + unsigned long flags; + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_DV) != 0) + printk("%s: %s Write Flow Control\n", ahd_name(ahd), + wrflow ? "enabling" : "disabling"); +#endif + + if (wrflow && spi_max_width(starget)) + ppr_options |= MSG_EXT_PPR_WR_FLOW; + + ahd_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + ahd_find_syncrate(ahd, &period, &ppr_options, + dt ? AHD_SYNCRATE_MAX : AHD_SYNCRATE_ULTRA2); + + ahd_lock(ahd, &flags); + ahd_set_syncrate(ahd, &devinfo, period, tinfo->goal.offset, + ppr_options, AHD_TRANS_GOAL, FALSE); + ahd_unlock(ahd, &flags); +} + +static void ahd_linux_set_rti(struct scsi_target *starget, int rti) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahd_softc *ahd = *((struct ahd_softc **)shost->hostdata); + struct ahd_tmode_tstate *tstate; + struct ahd_initiator_tinfo *tinfo + = ahd_fetch_transinfo(ahd, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahd_devinfo devinfo; + unsigned int ppr_options = tinfo->goal.ppr_options + & ~MSG_EXT_PPR_RTI; + unsigned int period = tinfo->goal.period; + unsigned int dt = ppr_options & MSG_EXT_PPR_DT_REQ; + unsigned long flags; + + if ((ahd->features & AHD_RTI) == 0) { +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_DV) != 0) + printk("%s: RTI not available\n", ahd_name(ahd)); +#endif + return; + } + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_DV) != 0) + printk("%s: %s RTI\n", ahd_name(ahd), + rti ? "enabling" : "disabling"); +#endif + + if (rti && spi_max_width(starget)) + ppr_options |= MSG_EXT_PPR_RTI; + + ahd_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + ahd_find_syncrate(ahd, &period, &ppr_options, + dt ? AHD_SYNCRATE_MAX : AHD_SYNCRATE_ULTRA2); + + ahd_lock(ahd, &flags); + ahd_set_syncrate(ahd, &devinfo, period, tinfo->goal.offset, + ppr_options, AHD_TRANS_GOAL, FALSE); + ahd_unlock(ahd, &flags); +} + +static void ahd_linux_set_pcomp_en(struct scsi_target *starget, int pcomp) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahd_softc *ahd = *((struct ahd_softc **)shost->hostdata); + struct ahd_tmode_tstate *tstate; + struct ahd_initiator_tinfo *tinfo + = ahd_fetch_transinfo(ahd, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahd_devinfo devinfo; + unsigned int ppr_options = tinfo->goal.ppr_options + & ~MSG_EXT_PPR_PCOMP_EN; + unsigned int period = tinfo->goal.period; + unsigned int dt = ppr_options & MSG_EXT_PPR_DT_REQ; + unsigned long flags; + +#ifdef AHD_DEBUG + if ((ahd_debug & AHD_SHOW_DV) != 0) + printk("%s: %s Precompensation\n", ahd_name(ahd), + pcomp ? "Enable" : "Disable"); +#endif + + if (pcomp && spi_max_width(starget)) { + uint8_t precomp; + + if (ahd->unit < ARRAY_SIZE(aic79xx_iocell_info)) { + const struct ahd_linux_iocell_opts *iocell_opts; + + iocell_opts = &aic79xx_iocell_info[ahd->unit]; + precomp = iocell_opts->precomp; + } else { + precomp = AIC79XX_DEFAULT_PRECOMP; + } + ppr_options |= MSG_EXT_PPR_PCOMP_EN; + AHD_SET_PRECOMP(ahd, precomp); + } else { + AHD_SET_PRECOMP(ahd, 0); + } + + ahd_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + ahd_find_syncrate(ahd, &period, &ppr_options, + dt ? AHD_SYNCRATE_MAX : AHD_SYNCRATE_ULTRA2); + + ahd_lock(ahd, &flags); + ahd_set_syncrate(ahd, &devinfo, period, tinfo->goal.offset, + ppr_options, AHD_TRANS_GOAL, FALSE); + ahd_unlock(ahd, &flags); +} + +static void ahd_linux_set_hold_mcs(struct scsi_target *starget, int hold) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahd_softc *ahd = *((struct ahd_softc **)shost->hostdata); + struct ahd_tmode_tstate *tstate; + struct ahd_initiator_tinfo *tinfo + = ahd_fetch_transinfo(ahd, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahd_devinfo devinfo; + unsigned int ppr_options = tinfo->goal.ppr_options + & ~MSG_EXT_PPR_HOLD_MCS; + unsigned int period = tinfo->goal.period; + unsigned int dt = ppr_options & MSG_EXT_PPR_DT_REQ; + unsigned long flags; + + if (hold && spi_max_width(starget)) + ppr_options |= MSG_EXT_PPR_HOLD_MCS; + + ahd_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + ahd_find_syncrate(ahd, &period, &ppr_options, + dt ? AHD_SYNCRATE_MAX : AHD_SYNCRATE_ULTRA2); + + ahd_lock(ahd, &flags); + ahd_set_syncrate(ahd, &devinfo, period, tinfo->goal.offset, + ppr_options, AHD_TRANS_GOAL, FALSE); + ahd_unlock(ahd, &flags); +} + +static void ahd_linux_get_signalling(struct Scsi_Host *shost) +{ + struct ahd_softc *ahd = *(struct ahd_softc **)shost->hostdata; + unsigned long flags; + u8 mode; + + ahd_lock(ahd, &flags); + ahd_pause(ahd); + mode = ahd_inb(ahd, SBLKCTL); + ahd_unpause(ahd); + ahd_unlock(ahd, &flags); + + if (mode & ENAB40) + spi_signalling(shost) = SPI_SIGNAL_LVD; + else if (mode & ENAB20) + spi_signalling(shost) = SPI_SIGNAL_SE; + else + spi_signalling(shost) = SPI_SIGNAL_UNKNOWN; +} + +static struct spi_function_template ahd_linux_transport_functions = { + .set_offset = ahd_linux_set_offset, + .show_offset = 1, + .set_period = ahd_linux_set_period, + .show_period = 1, + .set_width = ahd_linux_set_width, + .show_width = 1, + .set_dt = ahd_linux_set_dt, + .show_dt = 1, + .set_iu = ahd_linux_set_iu, + .show_iu = 1, + .set_qas = ahd_linux_set_qas, + .show_qas = 1, + .set_rd_strm = ahd_linux_set_rd_strm, + .show_rd_strm = 1, + .set_wr_flow = ahd_linux_set_wr_flow, + .show_wr_flow = 1, + .set_rti = ahd_linux_set_rti, + .show_rti = 1, + .set_pcomp_en = ahd_linux_set_pcomp_en, + .show_pcomp_en = 1, + .set_hold_mcs = ahd_linux_set_hold_mcs, + .show_hold_mcs = 1, + .get_signalling = ahd_linux_get_signalling, +}; + +static int __init +ahd_linux_init(void) +{ + int error = 0; + + /* + * If we've been passed any parameters, process them now. + */ + if (aic79xx) + aic79xx_setup(aic79xx); + + ahd_linux_transport_template = + spi_attach_transport(&ahd_linux_transport_functions); + if (!ahd_linux_transport_template) + return -ENODEV; + + scsi_transport_reserve_device(ahd_linux_transport_template, + sizeof(struct ahd_linux_device)); + + error = ahd_linux_pci_init(); + if (error) + spi_release_transport(ahd_linux_transport_template); + return error; +} + +static void __exit +ahd_linux_exit(void) +{ + ahd_linux_pci_exit(); + spi_release_transport(ahd_linux_transport_template); +} + +module_init(ahd_linux_init); +module_exit(ahd_linux_exit); diff --git a/drivers/scsi/aic7xxx/aic79xx_osm.h b/drivers/scsi/aic7xxx/aic79xx_osm.h new file mode 100644 index 000000000..8a8b7ae7a --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx_osm.h @@ -0,0 +1,683 @@ +/* + * Adaptec AIC79xx device driver for Linux. + * + * Copyright (c) 2000-2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic79xx_osm.h#166 $ + * + */ +#ifndef _AIC79XX_LINUX_H_ +#define _AIC79XX_LINUX_H_ + +#include <linux/types.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/ioport.h> +#include <linux/pci.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <asm/byteorder.h> +#include <asm/io.h> + +#include <scsi/scsi.h> +#include <scsi/scsi_cmnd.h> +#include <scsi/scsi_eh.h> +#include <scsi/scsi_device.h> +#include <scsi/scsi_host.h> +#include <scsi/scsi_tcq.h> +#include <scsi/scsi_transport.h> +#include <scsi/scsi_transport_spi.h> + +/* Core SCSI definitions */ +#define AIC_LIB_PREFIX ahd + +#include "cam.h" +#include "queue.h" +#include "scsi_message.h" +#include "scsi_iu.h" +#include "aiclib.h" + +/*********************************** Debugging ********************************/ +#ifdef CONFIG_AIC79XX_DEBUG_ENABLE +#ifdef CONFIG_AIC79XX_DEBUG_MASK +#define AHD_DEBUG 1 +#define AHD_DEBUG_OPTS CONFIG_AIC79XX_DEBUG_MASK +#else +/* + * Compile in debugging code, but do not enable any printfs. + */ +#define AHD_DEBUG 1 +#define AHD_DEBUG_OPTS 0 +#endif +/* No debugging code. */ +#endif + +/********************************** Misc Macros *******************************/ +#define powerof2(x) ((((x)-1)&(x))==0) + +/************************* Forward Declarations *******************************/ +struct ahd_softc; +typedef struct pci_dev *ahd_dev_softc_t; +typedef struct scsi_cmnd *ahd_io_ctx_t; + +/******************************* Byte Order ***********************************/ +#define ahd_htobe16(x) cpu_to_be16(x) +#define ahd_htobe32(x) cpu_to_be32(x) +#define ahd_htobe64(x) cpu_to_be64(x) +#define ahd_htole16(x) cpu_to_le16(x) +#define ahd_htole32(x) cpu_to_le32(x) +#define ahd_htole64(x) cpu_to_le64(x) + +#define ahd_be16toh(x) be16_to_cpu(x) +#define ahd_be32toh(x) be32_to_cpu(x) +#define ahd_be64toh(x) be64_to_cpu(x) +#define ahd_le16toh(x) le16_to_cpu(x) +#define ahd_le32toh(x) le32_to_cpu(x) +#define ahd_le64toh(x) le64_to_cpu(x) + +/************************* Configuration Data *********************************/ +extern uint32_t aic79xx_allow_memio; +extern struct scsi_host_template aic79xx_driver_template; + +/***************************** Bus Space/DMA **********************************/ + +typedef uint32_t bus_size_t; + +typedef enum { + BUS_SPACE_MEMIO, + BUS_SPACE_PIO +} bus_space_tag_t; + +typedef union { + u_long ioport; + volatile uint8_t __iomem *maddr; +} bus_space_handle_t; + +typedef struct bus_dma_segment +{ + dma_addr_t ds_addr; + bus_size_t ds_len; +} bus_dma_segment_t; + +struct ahd_linux_dma_tag +{ + bus_size_t alignment; + bus_size_t boundary; + bus_size_t maxsize; +}; +typedef struct ahd_linux_dma_tag* bus_dma_tag_t; + +typedef dma_addr_t bus_dmamap_t; + +typedef int bus_dma_filter_t(void*, dma_addr_t); +typedef void bus_dmamap_callback_t(void *, bus_dma_segment_t *, int, int); + +#define BUS_DMA_WAITOK 0x0 +#define BUS_DMA_NOWAIT 0x1 +#define BUS_DMA_ALLOCNOW 0x2 +#define BUS_DMA_LOAD_SEGS 0x4 /* + * Argument is an S/G list not + * a single buffer. + */ + +#define BUS_SPACE_MAXADDR 0xFFFFFFFF +#define BUS_SPACE_MAXADDR_32BIT 0xFFFFFFFF +#define BUS_SPACE_MAXSIZE_32BIT 0xFFFFFFFF + +int ahd_dma_tag_create(struct ahd_softc *, bus_dma_tag_t /*parent*/, + bus_size_t /*alignment*/, bus_size_t /*boundary*/, + dma_addr_t /*lowaddr*/, dma_addr_t /*highaddr*/, + bus_dma_filter_t*/*filter*/, void */*filterarg*/, + bus_size_t /*maxsize*/, int /*nsegments*/, + bus_size_t /*maxsegsz*/, int /*flags*/, + bus_dma_tag_t */*dma_tagp*/); + +void ahd_dma_tag_destroy(struct ahd_softc *, bus_dma_tag_t /*tag*/); + +int ahd_dmamem_alloc(struct ahd_softc *, bus_dma_tag_t /*dmat*/, + void** /*vaddr*/, int /*flags*/, + bus_dmamap_t* /*mapp*/); + +void ahd_dmamem_free(struct ahd_softc *, bus_dma_tag_t /*dmat*/, + void* /*vaddr*/, bus_dmamap_t /*map*/); + +void ahd_dmamap_destroy(struct ahd_softc *, bus_dma_tag_t /*tag*/, + bus_dmamap_t /*map*/); + +int ahd_dmamap_load(struct ahd_softc *ahd, bus_dma_tag_t /*dmat*/, + bus_dmamap_t /*map*/, void * /*buf*/, + bus_size_t /*buflen*/, bus_dmamap_callback_t *, + void */*callback_arg*/, int /*flags*/); + +int ahd_dmamap_unload(struct ahd_softc *, bus_dma_tag_t, bus_dmamap_t); + +/* + * Operations performed by ahd_dmamap_sync(). + */ +#define BUS_DMASYNC_PREREAD 0x01 /* pre-read synchronization */ +#define BUS_DMASYNC_POSTREAD 0x02 /* post-read synchronization */ +#define BUS_DMASYNC_PREWRITE 0x04 /* pre-write synchronization */ +#define BUS_DMASYNC_POSTWRITE 0x08 /* post-write synchronization */ + +/* + * XXX + * ahd_dmamap_sync is only used on buffers allocated with + * the pci_alloc_consistent() API. Although I'm not sure how + * this works on architectures with a write buffer, Linux does + * not have an API to sync "coherent" memory. Perhaps we need + * to do an mb()? + */ +#define ahd_dmamap_sync(ahd, dma_tag, dmamap, offset, len, op) + +/********************************** Includes **********************************/ +#ifdef CONFIG_AIC79XX_REG_PRETTY_PRINT +#define AIC_DEBUG_REGISTERS 1 +#else +#define AIC_DEBUG_REGISTERS 0 +#endif +#include "aic79xx.h" + +/***************************** SMP support ************************************/ +#include <linux/spinlock.h> + +#define AIC79XX_DRIVER_VERSION "3.0" + +/*************************** Device Data Structures ***************************/ +/* + * A per probed device structure used to deal with some error recovery + * scenarios that the Linux mid-layer code just doesn't know how to + * handle. The structure allocated for a device only becomes persistent + * after a successfully completed inquiry command to the target when + * that inquiry data indicates a lun is present. + */ + +typedef enum { + AHD_DEV_FREEZE_TIL_EMPTY = 0x02, /* Freeze queue until active == 0 */ + AHD_DEV_Q_BASIC = 0x10, /* Allow basic device queuing */ + AHD_DEV_Q_TAGGED = 0x20, /* Allow full SCSI2 command queueing */ + AHD_DEV_PERIODIC_OTAG = 0x40, /* Send OTAG to prevent starvation */ +} ahd_linux_dev_flags; + +struct ahd_linux_device { + TAILQ_ENTRY(ahd_linux_device) links; + + /* + * The number of transactions currently + * queued to the device. + */ + int active; + + /* + * The currently allowed number of + * transactions that can be queued to + * the device. Must be signed for + * conversion from tagged to untagged + * mode where the device may have more + * than one outstanding active transaction. + */ + int openings; + + /* + * A positive count indicates that this + * device's queue is halted. + */ + u_int qfrozen; + + /* + * Cumulative command counter. + */ + u_long commands_issued; + + /* + * The number of tagged transactions when + * running at our current opening level + * that have been successfully received by + * this device since the last QUEUE FULL. + */ + u_int tag_success_count; +#define AHD_TAG_SUCCESS_INTERVAL 50 + + ahd_linux_dev_flags flags; + + /* + * Per device timer. + */ + struct timer_list timer; + + /* + * The high limit for the tags variable. + */ + u_int maxtags; + + /* + * The computed number of tags outstanding + * at the time of the last QUEUE FULL event. + */ + u_int tags_on_last_queuefull; + + /* + * How many times we have seen a queue full + * with the same number of tags. This is used + * to stop our adaptive queue depth algorithm + * on devices with a fixed number of tags. + */ + u_int last_queuefull_same_count; +#define AHD_LOCK_TAGS_COUNT 50 + + /* + * How many transactions have been queued + * without the device going idle. We use + * this statistic to determine when to issue + * an ordered tag to prevent transaction + * starvation. This statistic is only updated + * if the AHD_DEV_PERIODIC_OTAG flag is set + * on this device. + */ + u_int commands_since_idle_or_otag; +#define AHD_OTAG_THRESH 500 +}; + +/********************* Definitions Required by the Core ***********************/ +/* + * Number of SG segments we require. So long as the S/G segments for + * a particular transaction are allocated in a physically contiguous + * manner and are allocated below 4GB, the number of S/G segments is + * unrestricted. + */ +#define AHD_NSEG 128 + +/* + * Per-SCB OSM storage. + */ +struct scb_platform_data { + struct ahd_linux_device *dev; + dma_addr_t buf_busaddr; + uint32_t xfer_len; + uint32_t sense_resid; /* Auto-Sense residual */ +}; + +/* + * Define a structure used for each host adapter. All members are + * aligned on a boundary >= the size of the member to honor the + * alignment restrictions of the various platforms supported by + * this driver. + */ +struct ahd_platform_data { + /* + * Fields accessed from interrupt context. + */ + struct scsi_target *starget[AHD_NUM_TARGETS]; + + spinlock_t spin_lock; + struct completion *eh_done; + struct Scsi_Host *host; /* pointer to scsi host */ +#define AHD_LINUX_NOIRQ ((uint32_t)~0) + uint32_t irq; /* IRQ for this adapter */ + uint32_t bios_address; + resource_size_t mem_busaddr; /* Mem Base Addr */ +}; + +void ahd_delay(long); + +/***************************** Low Level I/O **********************************/ +uint8_t ahd_inb(struct ahd_softc * ahd, long port); +void ahd_outb(struct ahd_softc * ahd, long port, uint8_t val); +void ahd_outw_atomic(struct ahd_softc * ahd, + long port, uint16_t val); +void ahd_outsb(struct ahd_softc * ahd, long port, + uint8_t *, int count); +void ahd_insb(struct ahd_softc * ahd, long port, + uint8_t *, int count); + +/**************************** Initialization **********************************/ +int ahd_linux_register_host(struct ahd_softc *, + struct scsi_host_template *); + +/******************************** Locking *************************************/ +static inline void +ahd_lockinit(struct ahd_softc *ahd) +{ + spin_lock_init(&ahd->platform_data->spin_lock); +} + +static inline void +ahd_lock(struct ahd_softc *ahd, unsigned long *flags) +{ + spin_lock_irqsave(&ahd->platform_data->spin_lock, *flags); +} + +static inline void +ahd_unlock(struct ahd_softc *ahd, unsigned long *flags) +{ + spin_unlock_irqrestore(&ahd->platform_data->spin_lock, *flags); +} + +/******************************* PCI Definitions ******************************/ +/* + * PCIM_xxx: mask to locate subfield in register + * PCIR_xxx: config register offset + * PCIC_xxx: device class + * PCIS_xxx: device subclass + * PCIP_xxx: device programming interface + * PCIV_xxx: PCI vendor ID (only required to fixup ancient devices) + * PCID_xxx: device ID + */ +#define PCIR_DEVVENDOR 0x00 +#define PCIR_VENDOR 0x00 +#define PCIR_DEVICE 0x02 +#define PCIR_COMMAND 0x04 +#define PCIM_CMD_PORTEN 0x0001 +#define PCIM_CMD_MEMEN 0x0002 +#define PCIM_CMD_BUSMASTEREN 0x0004 +#define PCIM_CMD_MWRICEN 0x0010 +#define PCIM_CMD_PERRESPEN 0x0040 +#define PCIM_CMD_SERRESPEN 0x0100 +#define PCIR_STATUS 0x06 +#define PCIR_REVID 0x08 +#define PCIR_PROGIF 0x09 +#define PCIR_SUBCLASS 0x0a +#define PCIR_CLASS 0x0b +#define PCIR_CACHELNSZ 0x0c +#define PCIR_LATTIMER 0x0d +#define PCIR_HEADERTYPE 0x0e +#define PCIM_MFDEV 0x80 +#define PCIR_BIST 0x0f +#define PCIR_CAP_PTR 0x34 + +/* config registers for header type 0 devices */ +#define PCIR_MAPS 0x10 +#define PCIR_SUBVEND_0 0x2c +#define PCIR_SUBDEV_0 0x2e + +/****************************** PCI-X definitions *****************************/ +#define PCIXR_COMMAND 0x96 +#define PCIXR_DEVADDR 0x98 +#define PCIXM_DEVADDR_FNUM 0x0003 /* Function Number */ +#define PCIXM_DEVADDR_DNUM 0x00F8 /* Device Number */ +#define PCIXM_DEVADDR_BNUM 0xFF00 /* Bus Number */ +#define PCIXR_STATUS 0x9A +#define PCIXM_STATUS_64BIT 0x0001 /* Active 64bit connection to device. */ +#define PCIXM_STATUS_133CAP 0x0002 /* Device is 133MHz capable */ +#define PCIXM_STATUS_SCDISC 0x0004 /* Split Completion Discarded */ +#define PCIXM_STATUS_UNEXPSC 0x0008 /* Unexpected Split Completion */ +#define PCIXM_STATUS_CMPLEXDEV 0x0010 /* Device Complexity (set == bridge) */ +#define PCIXM_STATUS_MAXMRDBC 0x0060 /* Maximum Burst Read Count */ +#define PCIXM_STATUS_MAXSPLITS 0x0380 /* Maximum Split Transactions */ +#define PCIXM_STATUS_MAXCRDS 0x1C00 /* Maximum Cumulative Read Size */ +#define PCIXM_STATUS_RCVDSCEM 0x2000 /* Received a Split Comp w/Error msg */ + +typedef enum +{ + AHD_POWER_STATE_D0, + AHD_POWER_STATE_D1, + AHD_POWER_STATE_D2, + AHD_POWER_STATE_D3 +} ahd_power_state; + +void ahd_power_state_change(struct ahd_softc *ahd, + ahd_power_state new_state); + +/******************************* PCI Routines *********************************/ +int ahd_linux_pci_init(void); +void ahd_linux_pci_exit(void); +int ahd_pci_map_registers(struct ahd_softc *ahd); +int ahd_pci_map_int(struct ahd_softc *ahd); + +uint32_t ahd_pci_read_config(ahd_dev_softc_t pci, + int reg, int width); +void ahd_pci_write_config(ahd_dev_softc_t pci, + int reg, uint32_t value, + int width); + +static inline int ahd_get_pci_function(ahd_dev_softc_t); +static inline int +ahd_get_pci_function(ahd_dev_softc_t pci) +{ + return (PCI_FUNC(pci->devfn)); +} + +static inline int ahd_get_pci_slot(ahd_dev_softc_t); +static inline int +ahd_get_pci_slot(ahd_dev_softc_t pci) +{ + return (PCI_SLOT(pci->devfn)); +} + +static inline int ahd_get_pci_bus(ahd_dev_softc_t); +static inline int +ahd_get_pci_bus(ahd_dev_softc_t pci) +{ + return (pci->bus->number); +} + +static inline void ahd_flush_device_writes(struct ahd_softc *); +static inline void +ahd_flush_device_writes(struct ahd_softc *ahd) +{ + /* XXX Is this sufficient for all architectures??? */ + ahd_inb(ahd, INTSTAT); +} + +/**************************** Proc FS Support *********************************/ +int ahd_proc_write_seeprom(struct Scsi_Host *, char *, int); +int ahd_linux_show_info(struct seq_file *,struct Scsi_Host *); + +/*********************** Transaction Access Wrappers **************************/ +static inline void ahd_cmd_set_transaction_status(struct scsi_cmnd *, uint32_t); +static inline void ahd_set_transaction_status(struct scb *, uint32_t); +static inline void ahd_cmd_set_scsi_status(struct scsi_cmnd *, uint32_t); +static inline void ahd_set_scsi_status(struct scb *, uint32_t); +static inline uint32_t ahd_cmd_get_transaction_status(struct scsi_cmnd *cmd); +static inline uint32_t ahd_get_transaction_status(struct scb *); +static inline uint32_t ahd_cmd_get_scsi_status(struct scsi_cmnd *cmd); +static inline uint32_t ahd_get_scsi_status(struct scb *); +static inline void ahd_set_transaction_tag(struct scb *, int, u_int); +static inline u_long ahd_get_transfer_length(struct scb *); +static inline int ahd_get_transfer_dir(struct scb *); +static inline void ahd_set_residual(struct scb *, u_long); +static inline void ahd_set_sense_residual(struct scb *scb, u_long resid); +static inline u_long ahd_get_residual(struct scb *); +static inline u_long ahd_get_sense_residual(struct scb *); +static inline int ahd_perform_autosense(struct scb *); +static inline uint32_t ahd_get_sense_bufsize(struct ahd_softc *, + struct scb *); +static inline void ahd_notify_xfer_settings_change(struct ahd_softc *, + struct ahd_devinfo *); +static inline void ahd_platform_scb_free(struct ahd_softc *ahd, + struct scb *scb); +static inline void ahd_freeze_scb(struct scb *scb); + +static inline +void ahd_cmd_set_transaction_status(struct scsi_cmnd *cmd, uint32_t status) +{ + cmd->result &= ~(CAM_STATUS_MASK << 16); + cmd->result |= status << 16; +} + +static inline +void ahd_set_transaction_status(struct scb *scb, uint32_t status) +{ + ahd_cmd_set_transaction_status(scb->io_ctx,status); +} + +static inline +void ahd_cmd_set_scsi_status(struct scsi_cmnd *cmd, uint32_t status) +{ + cmd->result &= ~0xFFFF; + cmd->result |= status; +} + +static inline +void ahd_set_scsi_status(struct scb *scb, uint32_t status) +{ + ahd_cmd_set_scsi_status(scb->io_ctx, status); +} + +static inline +uint32_t ahd_cmd_get_transaction_status(struct scsi_cmnd *cmd) +{ + return ((cmd->result >> 16) & CAM_STATUS_MASK); +} + +static inline +uint32_t ahd_get_transaction_status(struct scb *scb) +{ + return (ahd_cmd_get_transaction_status(scb->io_ctx)); +} + +static inline +uint32_t ahd_cmd_get_scsi_status(struct scsi_cmnd *cmd) +{ + return (cmd->result & 0xFFFF); +} + +static inline +uint32_t ahd_get_scsi_status(struct scb *scb) +{ + return (ahd_cmd_get_scsi_status(scb->io_ctx)); +} + +static inline +void ahd_set_transaction_tag(struct scb *scb, int enabled, u_int type) +{ + /* + * Nothing to do for linux as the incoming transaction + * has no concept of tag/non tagged, etc. + */ +} + +static inline +u_long ahd_get_transfer_length(struct scb *scb) +{ + return (scb->platform_data->xfer_len); +} + +static inline +int ahd_get_transfer_dir(struct scb *scb) +{ + return (scb->io_ctx->sc_data_direction); +} + +static inline +void ahd_set_residual(struct scb *scb, u_long resid) +{ + scsi_set_resid(scb->io_ctx, resid); +} + +static inline +void ahd_set_sense_residual(struct scb *scb, u_long resid) +{ + scb->platform_data->sense_resid = resid; +} + +static inline +u_long ahd_get_residual(struct scb *scb) +{ + return scsi_get_resid(scb->io_ctx); +} + +static inline +u_long ahd_get_sense_residual(struct scb *scb) +{ + return (scb->platform_data->sense_resid); +} + +static inline +int ahd_perform_autosense(struct scb *scb) +{ + /* + * We always perform autosense in Linux. + * On other platforms this is set on a + * per-transaction basis. + */ + return (1); +} + +static inline uint32_t +ahd_get_sense_bufsize(struct ahd_softc *ahd, struct scb *scb) +{ + return (sizeof(struct scsi_sense_data)); +} + +static inline void +ahd_notify_xfer_settings_change(struct ahd_softc *ahd, + struct ahd_devinfo *devinfo) +{ + /* Nothing to do here for linux */ +} + +static inline void +ahd_platform_scb_free(struct ahd_softc *ahd, struct scb *scb) +{ + ahd->flags &= ~AHD_RESOURCE_SHORTAGE; +} + +int ahd_platform_alloc(struct ahd_softc *ahd, void *platform_arg); +void ahd_platform_free(struct ahd_softc *ahd); +void ahd_platform_init(struct ahd_softc *ahd); +void ahd_platform_freeze_devq(struct ahd_softc *ahd, struct scb *scb); + +static inline void +ahd_freeze_scb(struct scb *scb) +{ + if ((scb->io_ctx->result & (CAM_DEV_QFRZN << 16)) == 0) { + scb->io_ctx->result |= CAM_DEV_QFRZN << 16; + scb->platform_data->dev->qfrozen++; + } +} + +void ahd_platform_set_tags(struct ahd_softc *ahd, struct scsi_device *sdev, + struct ahd_devinfo *devinfo, ahd_queue_alg); +int ahd_platform_abort_scbs(struct ahd_softc *ahd, int target, + char channel, int lun, u_int tag, + role_t role, uint32_t status); +irqreturn_t + ahd_linux_isr(int irq, void *dev_id); +void ahd_done(struct ahd_softc*, struct scb*); +void ahd_send_async(struct ahd_softc *, char channel, + u_int target, u_int lun, ac_code); +void ahd_print_path(struct ahd_softc *, struct scb *); + +#ifdef CONFIG_PCI +#define AHD_PCI_CONFIG 1 +#else +#define AHD_PCI_CONFIG 0 +#endif +#define bootverbose aic79xx_verbose +extern uint32_t aic79xx_verbose; + +#endif /* _AIC79XX_LINUX_H_ */ diff --git a/drivers/scsi/aic7xxx/aic79xx_osm_pci.c b/drivers/scsi/aic7xxx/aic79xx_osm_pci.c new file mode 100644 index 000000000..8b891a05d --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx_osm_pci.c @@ -0,0 +1,397 @@ +/* + * Linux driver attachment glue for PCI based U320 controllers. + * + * Copyright (c) 2000-2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic79xx_osm_pci.c#25 $ + */ + +#include "aic79xx_osm.h" +#include "aic79xx_inline.h" +#include "aic79xx_pci.h" + +/* Define the macro locally since it's different for different class of chips. + */ +#define ID(x) \ + ID2C(x), \ + ID2C(IDIROC(x)) + +static const struct pci_device_id ahd_linux_pci_id_table[] = { + /* aic7901 based controllers */ + ID(ID_AHA_29320A), + ID(ID_AHA_29320ALP), + ID(ID_AHA_29320LPE), + /* aic7902 based controllers */ + ID(ID_AHA_29320), + ID(ID_AHA_29320B), + ID(ID_AHA_29320LP), + ID(ID_AHA_39320), + ID(ID_AHA_39320_B), + ID(ID_AHA_39320A), + ID(ID_AHA_39320D), + ID(ID_AHA_39320D_HP), + ID(ID_AHA_39320D_B), + ID(ID_AHA_39320D_B_HP), + /* Generic chip probes for devices we don't know exactly. */ + ID16(ID_AIC7901 & ID_9005_GENERIC_MASK), + ID(ID_AIC7901A & ID_DEV_VENDOR_MASK), + ID16(ID_AIC7902 & ID_9005_GENERIC_MASK), + { 0 } +}; + +MODULE_DEVICE_TABLE(pci, ahd_linux_pci_id_table); + +#ifdef CONFIG_PM +static int +ahd_linux_pci_dev_suspend(struct pci_dev *pdev, pm_message_t mesg) +{ + struct ahd_softc *ahd = pci_get_drvdata(pdev); + int rc; + + if ((rc = ahd_suspend(ahd))) + return rc; + + ahd_pci_suspend(ahd); + + pci_save_state(pdev); + pci_disable_device(pdev); + + if (mesg.event & PM_EVENT_SLEEP) + pci_set_power_state(pdev, PCI_D3hot); + + return rc; +} + +static int +ahd_linux_pci_dev_resume(struct pci_dev *pdev) +{ + struct ahd_softc *ahd = pci_get_drvdata(pdev); + int rc; + + pci_set_power_state(pdev, PCI_D0); + pci_restore_state(pdev); + + if ((rc = pci_enable_device(pdev))) { + dev_printk(KERN_ERR, &pdev->dev, + "failed to enable device after resume (%d)\n", rc); + return rc; + } + + pci_set_master(pdev); + + ahd_pci_resume(ahd); + + ahd_resume(ahd); + + return rc; +} +#endif + +static void +ahd_linux_pci_dev_remove(struct pci_dev *pdev) +{ + struct ahd_softc *ahd = pci_get_drvdata(pdev); + u_long s; + + if (ahd->platform_data && ahd->platform_data->host) + scsi_remove_host(ahd->platform_data->host); + + ahd_lock(ahd, &s); + ahd_intr_enable(ahd, FALSE); + ahd_unlock(ahd, &s); + ahd_free(ahd); +} + +static void +ahd_linux_pci_inherit_flags(struct ahd_softc *ahd) +{ + struct pci_dev *pdev = ahd->dev_softc, *master_pdev; + unsigned int master_devfn = PCI_DEVFN(PCI_SLOT(pdev->devfn), 0); + + master_pdev = pci_get_slot(pdev->bus, master_devfn); + if (master_pdev) { + struct ahd_softc *master = pci_get_drvdata(master_pdev); + if (master) { + ahd->flags &= ~AHD_BIOS_ENABLED; + ahd->flags |= master->flags & AHD_BIOS_ENABLED; + } else + printk(KERN_ERR "aic79xx: no multichannel peer found!\n"); + pci_dev_put(master_pdev); + } +} + +static int +ahd_linux_pci_dev_probe(struct pci_dev *pdev, const struct pci_device_id *ent) +{ + char buf[80]; + struct ahd_softc *ahd; + ahd_dev_softc_t pci; + const struct ahd_pci_identity *entry; + char *name; + int error; + struct device *dev = &pdev->dev; + + pci = pdev; + entry = ahd_find_pci_device(pci); + if (entry == NULL) + return (-ENODEV); + + /* + * Allocate a softc for this card and + * set it up for attachment by our + * common detect routine. + */ + sprintf(buf, "ahd_pci:%d:%d:%d", + ahd_get_pci_bus(pci), + ahd_get_pci_slot(pci), + ahd_get_pci_function(pci)); + name = kstrdup(buf, GFP_ATOMIC); + if (name == NULL) + return (-ENOMEM); + ahd = ahd_alloc(NULL, name); + if (ahd == NULL) + return (-ENOMEM); + if (pci_enable_device(pdev)) { + ahd_free(ahd); + return (-ENODEV); + } + pci_set_master(pdev); + + if (sizeof(dma_addr_t) > 4) { + const u64 required_mask = dma_get_required_mask(dev); + + if (required_mask > DMA_BIT_MASK(39) && + dma_set_mask(dev, DMA_BIT_MASK(64)) == 0) + ahd->flags |= AHD_64BIT_ADDRESSING; + else if (required_mask > DMA_BIT_MASK(32) && + dma_set_mask(dev, DMA_BIT_MASK(39)) == 0) + ahd->flags |= AHD_39BIT_ADDRESSING; + else + dma_set_mask(dev, DMA_BIT_MASK(32)); + } else { + dma_set_mask(dev, DMA_BIT_MASK(32)); + } + ahd->dev_softc = pci; + error = ahd_pci_config(ahd, entry); + if (error != 0) { + ahd_free(ahd); + return (-error); + } + + /* + * Second Function PCI devices need to inherit some + * * settings from function 0. + */ + if ((ahd->features & AHD_MULTI_FUNC) && PCI_FUNC(pdev->devfn) != 0) + ahd_linux_pci_inherit_flags(ahd); + + pci_set_drvdata(pdev, ahd); + + ahd_linux_register_host(ahd, &aic79xx_driver_template); + return (0); +} + +static struct pci_driver aic79xx_pci_driver = { + .name = "aic79xx", + .probe = ahd_linux_pci_dev_probe, +#ifdef CONFIG_PM + .suspend = ahd_linux_pci_dev_suspend, + .resume = ahd_linux_pci_dev_resume, +#endif + .remove = ahd_linux_pci_dev_remove, + .id_table = ahd_linux_pci_id_table +}; + +int +ahd_linux_pci_init(void) +{ + return pci_register_driver(&aic79xx_pci_driver); +} + +void +ahd_linux_pci_exit(void) +{ + pci_unregister_driver(&aic79xx_pci_driver); +} + +static int +ahd_linux_pci_reserve_io_regions(struct ahd_softc *ahd, resource_size_t *base, + resource_size_t *base2) +{ + *base = pci_resource_start(ahd->dev_softc, 0); + /* + * This is really the 3rd bar and should be at index 2, + * but the Linux PCI code doesn't know how to "count" 64bit + * bars. + */ + *base2 = pci_resource_start(ahd->dev_softc, 3); + if (*base == 0 || *base2 == 0) + return (ENOMEM); + if (!request_region(*base, 256, "aic79xx")) + return (ENOMEM); + if (!request_region(*base2, 256, "aic79xx")) { + release_region(*base, 256); + return (ENOMEM); + } + return (0); +} + +static int +ahd_linux_pci_reserve_mem_region(struct ahd_softc *ahd, + resource_size_t *bus_addr, + uint8_t __iomem **maddr) +{ + resource_size_t start; + resource_size_t base_page; + u_long base_offset; + int error = 0; + + if (aic79xx_allow_memio == 0) + return (ENOMEM); + + if ((ahd->bugs & AHD_PCIX_MMAPIO_BUG) != 0) + return (ENOMEM); + + start = pci_resource_start(ahd->dev_softc, 1); + base_page = start & PAGE_MASK; + base_offset = start - base_page; + if (start != 0) { + *bus_addr = start; + if (!request_mem_region(start, 0x1000, "aic79xx")) + error = ENOMEM; + if (!error) { + *maddr = ioremap(base_page, base_offset + 512); + if (*maddr == NULL) { + error = ENOMEM; + release_mem_region(start, 0x1000); + } else + *maddr += base_offset; + } + } else + error = ENOMEM; + return (error); +} + +int +ahd_pci_map_registers(struct ahd_softc *ahd) +{ + uint32_t command; + resource_size_t base; + uint8_t __iomem *maddr; + int error; + + /* + * If its allowed, we prefer memory mapped access. + */ + command = ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, 4); + command &= ~(PCIM_CMD_PORTEN|PCIM_CMD_MEMEN); + base = 0; + maddr = NULL; + error = ahd_linux_pci_reserve_mem_region(ahd, &base, &maddr); + if (error == 0) { + ahd->platform_data->mem_busaddr = base; + ahd->tags[0] = BUS_SPACE_MEMIO; + ahd->bshs[0].maddr = maddr; + ahd->tags[1] = BUS_SPACE_MEMIO; + ahd->bshs[1].maddr = maddr + 0x100; + ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, + command | PCIM_CMD_MEMEN, 4); + + if (ahd_pci_test_register_access(ahd) != 0) { + + printk("aic79xx: PCI Device %d:%d:%d " + "failed memory mapped test. Using PIO.\n", + ahd_get_pci_bus(ahd->dev_softc), + ahd_get_pci_slot(ahd->dev_softc), + ahd_get_pci_function(ahd->dev_softc)); + iounmap(maddr); + release_mem_region(ahd->platform_data->mem_busaddr, + 0x1000); + ahd->bshs[0].maddr = NULL; + maddr = NULL; + } else + command |= PCIM_CMD_MEMEN; + } else if (bootverbose) { + printk("aic79xx: PCI%d:%d:%d MEM region 0x%llx " + "unavailable. Cannot memory map device.\n", + ahd_get_pci_bus(ahd->dev_softc), + ahd_get_pci_slot(ahd->dev_softc), + ahd_get_pci_function(ahd->dev_softc), + (unsigned long long)base); + } + + if (maddr == NULL) { + resource_size_t base2; + + error = ahd_linux_pci_reserve_io_regions(ahd, &base, &base2); + if (error == 0) { + ahd->tags[0] = BUS_SPACE_PIO; + ahd->tags[1] = BUS_SPACE_PIO; + ahd->bshs[0].ioport = (u_long)base; + ahd->bshs[1].ioport = (u_long)base2; + command |= PCIM_CMD_PORTEN; + } else { + printk("aic79xx: PCI%d:%d:%d IO regions 0x%llx and " + "0x%llx unavailable. Cannot map device.\n", + ahd_get_pci_bus(ahd->dev_softc), + ahd_get_pci_slot(ahd->dev_softc), + ahd_get_pci_function(ahd->dev_softc), + (unsigned long long)base, + (unsigned long long)base2); + } + } + ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, command, 4); + return (error); +} + +int +ahd_pci_map_int(struct ahd_softc *ahd) +{ + int error; + + error = request_irq(ahd->dev_softc->irq, ahd_linux_isr, + IRQF_SHARED, "aic79xx", ahd); + if (!error) + ahd->platform_data->irq = ahd->dev_softc->irq; + + return (-error); +} + +void +ahd_power_state_change(struct ahd_softc *ahd, ahd_power_state new_state) +{ + pci_set_power_state(ahd->dev_softc, new_state); +} diff --git a/drivers/scsi/aic7xxx/aic79xx_pci.c b/drivers/scsi/aic7xxx/aic79xx_pci.c new file mode 100644 index 000000000..8397ae93f --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx_pci.c @@ -0,0 +1,1006 @@ +/* + * Product specific probe and attach routines for: + * aic7901 and aic7902 SCSI controllers + * + * Copyright (c) 1994-2001 Justin T. Gibbs. + * Copyright (c) 2000-2002 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aic79xx_pci.c#92 $ + */ + +#include "aic79xx_osm.h" +#include "aic79xx_inline.h" +#include "aic79xx_pci.h" + +static inline uint64_t +ahd_compose_id(u_int device, u_int vendor, u_int subdevice, u_int subvendor) +{ + uint64_t id; + + id = subvendor + | (subdevice << 16) + | ((uint64_t)vendor << 32) + | ((uint64_t)device << 48); + + return (id); +} + +#define ID_AIC7902_PCI_REV_A4 0x3 +#define ID_AIC7902_PCI_REV_B0 0x10 +#define SUBID_HP 0x0E11 + +#define DEVID_9005_HOSTRAID(id) ((id) & 0x80) + +#define DEVID_9005_TYPE(id) ((id) & 0xF) +#define DEVID_9005_TYPE_HBA 0x0 /* Standard Card */ +#define DEVID_9005_TYPE_HBA_2EXT 0x1 /* 2 External Ports */ +#define DEVID_9005_TYPE_IROC 0x8 /* Raid(0,1,10) Card */ +#define DEVID_9005_TYPE_MB 0xF /* On Motherboard */ + +#define DEVID_9005_MFUNC(id) ((id) & 0x10) + +#define DEVID_9005_PACKETIZED(id) ((id) & 0x8000) + +#define SUBID_9005_TYPE(id) ((id) & 0xF) +#define SUBID_9005_TYPE_HBA 0x0 /* Standard Card */ +#define SUBID_9005_TYPE_MB 0xF /* On Motherboard */ + +#define SUBID_9005_AUTOTERM(id) (((id) & 0x10) == 0) + +#define SUBID_9005_LEGACYCONN_FUNC(id) ((id) & 0x20) + +#define SUBID_9005_SEEPTYPE(id) (((id) & 0x0C0) >> 6) +#define SUBID_9005_SEEPTYPE_NONE 0x0 +#define SUBID_9005_SEEPTYPE_4K 0x1 + +static ahd_device_setup_t ahd_aic7901_setup; +static ahd_device_setup_t ahd_aic7901A_setup; +static ahd_device_setup_t ahd_aic7902_setup; +static ahd_device_setup_t ahd_aic790X_setup; + +static const struct ahd_pci_identity ahd_pci_ident_table[] = +{ + /* aic7901 based controllers */ + { + ID_AHA_29320A, + ID_ALL_MASK, + "Adaptec 29320A Ultra320 SCSI adapter", + ahd_aic7901_setup + }, + { + ID_AHA_29320ALP, + ID_ALL_MASK, + "Adaptec 29320ALP PCIx Ultra320 SCSI adapter", + ahd_aic7901_setup + }, + { + ID_AHA_29320LPE, + ID_ALL_MASK, + "Adaptec 29320LPE PCIe Ultra320 SCSI adapter", + ahd_aic7901_setup + }, + /* aic7901A based controllers */ + { + ID_AHA_29320LP, + ID_ALL_MASK, + "Adaptec 29320LP Ultra320 SCSI adapter", + ahd_aic7901A_setup + }, + /* aic7902 based controllers */ + { + ID_AHA_29320, + ID_ALL_MASK, + "Adaptec 29320 Ultra320 SCSI adapter", + ahd_aic7902_setup + }, + { + ID_AHA_29320B, + ID_ALL_MASK, + "Adaptec 29320B Ultra320 SCSI adapter", + ahd_aic7902_setup + }, + { + ID_AHA_39320, + ID_ALL_MASK, + "Adaptec 39320 Ultra320 SCSI adapter", + ahd_aic7902_setup + }, + { + ID_AHA_39320_B, + ID_ALL_MASK, + "Adaptec 39320 Ultra320 SCSI adapter", + ahd_aic7902_setup + }, + { + ID_AHA_39320_B_DELL, + ID_ALL_MASK, + "Adaptec (Dell OEM) 39320 Ultra320 SCSI adapter", + ahd_aic7902_setup + }, + { + ID_AHA_39320A, + ID_ALL_MASK, + "Adaptec 39320A Ultra320 SCSI adapter", + ahd_aic7902_setup + }, + { + ID_AHA_39320D, + ID_ALL_MASK, + "Adaptec 39320D Ultra320 SCSI adapter", + ahd_aic7902_setup + }, + { + ID_AHA_39320D_HP, + ID_ALL_MASK, + "Adaptec (HP OEM) 39320D Ultra320 SCSI adapter", + ahd_aic7902_setup + }, + { + ID_AHA_39320D_B, + ID_ALL_MASK, + "Adaptec 39320D Ultra320 SCSI adapter", + ahd_aic7902_setup + }, + { + ID_AHA_39320D_B_HP, + ID_ALL_MASK, + "Adaptec (HP OEM) 39320D Ultra320 SCSI adapter", + ahd_aic7902_setup + }, + /* Generic chip probes for devices we don't know 'exactly' */ + { + ID_AIC7901 & ID_9005_GENERIC_MASK, + ID_9005_GENERIC_MASK, + "Adaptec AIC7901 Ultra320 SCSI adapter", + ahd_aic7901_setup + }, + { + ID_AIC7901A & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec AIC7901A Ultra320 SCSI adapter", + ahd_aic7901A_setup + }, + { + ID_AIC7902 & ID_9005_GENERIC_MASK, + ID_9005_GENERIC_MASK, + "Adaptec AIC7902 Ultra320 SCSI adapter", + ahd_aic7902_setup + } +}; + +static const u_int ahd_num_pci_devs = ARRAY_SIZE(ahd_pci_ident_table); + +#define DEVCONFIG 0x40 +#define PCIXINITPAT 0x0000E000ul +#define PCIXINIT_PCI33_66 0x0000E000ul +#define PCIXINIT_PCIX50_66 0x0000C000ul +#define PCIXINIT_PCIX66_100 0x0000A000ul +#define PCIXINIT_PCIX100_133 0x00008000ul +#define PCI_BUS_MODES_INDEX(devconfig) \ + (((devconfig) & PCIXINITPAT) >> 13) +static const char *pci_bus_modes[] = +{ + "PCI bus mode unknown", + "PCI bus mode unknown", + "PCI bus mode unknown", + "PCI bus mode unknown", + "PCI-X 101-133MHz", + "PCI-X 67-100MHz", + "PCI-X 50-66MHz", + "PCI 33 or 66MHz" +}; + +#define TESTMODE 0x00000800ul +#define IRDY_RST 0x00000200ul +#define FRAME_RST 0x00000100ul +#define PCI64BIT 0x00000080ul +#define MRDCEN 0x00000040ul +#define ENDIANSEL 0x00000020ul +#define MIXQWENDIANEN 0x00000008ul +#define DACEN 0x00000004ul +#define STPWLEVEL 0x00000002ul +#define QWENDIANSEL 0x00000001ul + +#define DEVCONFIG1 0x44 +#define PREQDIS 0x01 + +#define CSIZE_LATTIME 0x0c +#define CACHESIZE 0x000000fful +#define LATTIME 0x0000ff00ul + +static int ahd_check_extport(struct ahd_softc *ahd); +static void ahd_configure_termination(struct ahd_softc *ahd, + u_int adapter_control); +static void ahd_pci_split_intr(struct ahd_softc *ahd, u_int intstat); +static void ahd_pci_intr(struct ahd_softc *ahd); + +const struct ahd_pci_identity * +ahd_find_pci_device(ahd_dev_softc_t pci) +{ + uint64_t full_id; + uint16_t device; + uint16_t vendor; + uint16_t subdevice; + uint16_t subvendor; + const struct ahd_pci_identity *entry; + u_int i; + + vendor = ahd_pci_read_config(pci, PCIR_DEVVENDOR, /*bytes*/2); + device = ahd_pci_read_config(pci, PCIR_DEVICE, /*bytes*/2); + subvendor = ahd_pci_read_config(pci, PCIR_SUBVEND_0, /*bytes*/2); + subdevice = ahd_pci_read_config(pci, PCIR_SUBDEV_0, /*bytes*/2); + full_id = ahd_compose_id(device, + vendor, + subdevice, + subvendor); + + /* + * Controllers, mask out the IROC/HostRAID bit + */ + + full_id &= ID_ALL_IROC_MASK; + + for (i = 0; i < ahd_num_pci_devs; i++) { + entry = &ahd_pci_ident_table[i]; + if (entry->full_id == (full_id & entry->id_mask)) { + /* Honor exclusion entries. */ + if (entry->name == NULL) + return (NULL); + return (entry); + } + } + return (NULL); +} + +int +ahd_pci_config(struct ahd_softc *ahd, const struct ahd_pci_identity *entry) +{ + u_int command; + uint32_t devconfig; + uint16_t subvendor; + int error; + + ahd->description = entry->name; + /* + * Record if this is an HP board. + */ + subvendor = ahd_pci_read_config(ahd->dev_softc, + PCIR_SUBVEND_0, /*bytes*/2); + if (subvendor == SUBID_HP) + ahd->flags |= AHD_HP_BOARD; + + error = entry->setup(ahd); + if (error != 0) + return (error); + + devconfig = ahd_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4); + if ((devconfig & PCIXINITPAT) == PCIXINIT_PCI33_66) { + ahd->chip |= AHD_PCI; + /* Disable PCIX workarounds when running in PCI mode. */ + ahd->bugs &= ~AHD_PCIX_BUG_MASK; + } else { + ahd->chip |= AHD_PCIX; + } + ahd->bus_description = pci_bus_modes[PCI_BUS_MODES_INDEX(devconfig)]; + + ahd_power_state_change(ahd, AHD_POWER_STATE_D0); + + error = ahd_pci_map_registers(ahd); + if (error != 0) + return (error); + + /* + * If we need to support high memory, enable dual + * address cycles. This bit must be set to enable + * high address bit generation even if we are on a + * 64bit bus (PCI64BIT set in devconfig). + */ + if ((ahd->flags & (AHD_39BIT_ADDRESSING|AHD_64BIT_ADDRESSING)) != 0) { + if (bootverbose) + printk("%s: Enabling 39Bit Addressing\n", + ahd_name(ahd)); + devconfig = ahd_pci_read_config(ahd->dev_softc, + DEVCONFIG, /*bytes*/4); + devconfig |= DACEN; + ahd_pci_write_config(ahd->dev_softc, DEVCONFIG, + devconfig, /*bytes*/4); + } + + /* Ensure busmastering is enabled */ + command = ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2); + command |= PCIM_CMD_BUSMASTEREN; + ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, command, /*bytes*/2); + + error = ahd_softc_init(ahd); + if (error != 0) + return (error); + + ahd->bus_intr = ahd_pci_intr; + + error = ahd_reset(ahd, /*reinit*/FALSE); + if (error != 0) + return (ENXIO); + + ahd->pci_cachesize = + ahd_pci_read_config(ahd->dev_softc, CSIZE_LATTIME, + /*bytes*/1) & CACHESIZE; + ahd->pci_cachesize *= 4; + + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + /* See if we have a SEEPROM and perform auto-term */ + error = ahd_check_extport(ahd); + if (error != 0) + return (error); + + /* Core initialization */ + error = ahd_init(ahd); + if (error != 0) + return (error); + ahd->init_level++; + + /* + * Allow interrupts now that we are completely setup. + */ + return ahd_pci_map_int(ahd); +} + +#ifdef CONFIG_PM +void +ahd_pci_suspend(struct ahd_softc *ahd) +{ + /* + * Save chip register configuration data for chip resets + * that occur during runtime and resume events. + */ + ahd->suspend_state.pci_state.devconfig = + ahd_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4); + ahd->suspend_state.pci_state.command = + ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/1); + ahd->suspend_state.pci_state.csize_lattime = + ahd_pci_read_config(ahd->dev_softc, CSIZE_LATTIME, /*bytes*/1); + +} + +void +ahd_pci_resume(struct ahd_softc *ahd) +{ + ahd_pci_write_config(ahd->dev_softc, DEVCONFIG, + ahd->suspend_state.pci_state.devconfig, /*bytes*/4); + ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, + ahd->suspend_state.pci_state.command, /*bytes*/1); + ahd_pci_write_config(ahd->dev_softc, CSIZE_LATTIME, + ahd->suspend_state.pci_state.csize_lattime, /*bytes*/1); +} +#endif + +/* + * Perform some simple tests that should catch situations where + * our registers are invalidly mapped. + */ +int +ahd_pci_test_register_access(struct ahd_softc *ahd) +{ + uint32_t cmd; + u_int targpcistat; + u_int pci_status1; + int error; + uint8_t hcntrl; + + error = EIO; + + /* + * Enable PCI error interrupt status, but suppress NMIs + * generated by SERR raised due to target aborts. + */ + cmd = ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2); + ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, + cmd & ~PCIM_CMD_SERRESPEN, /*bytes*/2); + + /* + * First a simple test to see if any + * registers can be read. Reading + * HCNTRL has no side effects and has + * at least one bit that is guaranteed to + * be zero so it is a good register to + * use for this test. + */ + hcntrl = ahd_inb(ahd, HCNTRL); + if (hcntrl == 0xFF) + goto fail; + + /* + * Next create a situation where write combining + * or read prefetching could be initiated by the + * CPU or host bridge. Our device does not support + * either, so look for data corruption and/or flaged + * PCI errors. First pause without causing another + * chip reset. + */ + hcntrl &= ~CHIPRST; + ahd_outb(ahd, HCNTRL, hcntrl|PAUSE); + while (ahd_is_paused(ahd) == 0) + ; + + /* Clear any PCI errors that occurred before our driver attached. */ + ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); + targpcistat = ahd_inb(ahd, TARGPCISTAT); + ahd_outb(ahd, TARGPCISTAT, targpcistat); + pci_status1 = ahd_pci_read_config(ahd->dev_softc, + PCIR_STATUS + 1, /*bytes*/1); + ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, + pci_status1, /*bytes*/1); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + ahd_outb(ahd, CLRINT, CLRPCIINT); + + ahd_outb(ahd, SEQCTL0, PERRORDIS); + ahd_outl(ahd, SRAM_BASE, 0x5aa555aa); + if (ahd_inl(ahd, SRAM_BASE) != 0x5aa555aa) + goto fail; + + if ((ahd_inb(ahd, INTSTAT) & PCIINT) != 0) { + ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); + targpcistat = ahd_inb(ahd, TARGPCISTAT); + if ((targpcistat & STA) != 0) + goto fail; + } + + error = 0; + +fail: + if ((ahd_inb(ahd, INTSTAT) & PCIINT) != 0) { + + ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); + targpcistat = ahd_inb(ahd, TARGPCISTAT); + + /* Silently clear any latched errors. */ + ahd_outb(ahd, TARGPCISTAT, targpcistat); + pci_status1 = ahd_pci_read_config(ahd->dev_softc, + PCIR_STATUS + 1, /*bytes*/1); + ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, + pci_status1, /*bytes*/1); + ahd_outb(ahd, CLRINT, CLRPCIINT); + } + ahd_outb(ahd, SEQCTL0, PERRORDIS|FAILDIS); + ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, cmd, /*bytes*/2); + return (error); +} + +/* + * Check the external port logic for a serial eeprom + * and termination/cable detection contrls. + */ +static int +ahd_check_extport(struct ahd_softc *ahd) +{ + struct vpd_config vpd; + struct seeprom_config *sc; + u_int adapter_control; + int have_seeprom; + int error; + + sc = ahd->seep_config; + have_seeprom = ahd_acquire_seeprom(ahd); + if (have_seeprom) { + u_int start_addr; + + /* + * Fetch VPD for this function and parse it. + */ + if (bootverbose) + printk("%s: Reading VPD from SEEPROM...", + ahd_name(ahd)); + + /* Address is always in units of 16bit words */ + start_addr = ((2 * sizeof(*sc)) + + (sizeof(vpd) * (ahd->channel - 'A'))) / 2; + + error = ahd_read_seeprom(ahd, (uint16_t *)&vpd, + start_addr, sizeof(vpd)/2, + /*bytestream*/TRUE); + if (error == 0) + error = ahd_parse_vpddata(ahd, &vpd); + if (bootverbose) + printk("%s: VPD parsing %s\n", + ahd_name(ahd), + error == 0 ? "successful" : "failed"); + + if (bootverbose) + printk("%s: Reading SEEPROM...", ahd_name(ahd)); + + /* Address is always in units of 16bit words */ + start_addr = (sizeof(*sc) / 2) * (ahd->channel - 'A'); + + error = ahd_read_seeprom(ahd, (uint16_t *)sc, + start_addr, sizeof(*sc)/2, + /*bytestream*/FALSE); + + if (error != 0) { + printk("Unable to read SEEPROM\n"); + have_seeprom = 0; + } else { + have_seeprom = ahd_verify_cksum(sc); + + if (bootverbose) { + if (have_seeprom == 0) + printk ("checksum error\n"); + else + printk ("done.\n"); + } + } + ahd_release_seeprom(ahd); + } + + if (!have_seeprom) { + u_int nvram_scb; + + /* + * Pull scratch ram settings and treat them as + * if they are the contents of an seeprom if + * the 'ADPT', 'BIOS', or 'ASPI' signature is found + * in SCB 0xFF. We manually compose the data as 16bit + * values to avoid endian issues. + */ + ahd_set_scbptr(ahd, 0xFF); + nvram_scb = ahd_inb_scbram(ahd, SCB_BASE + NVRAM_SCB_OFFSET); + if (nvram_scb != 0xFF + && ((ahd_inb_scbram(ahd, SCB_BASE + 0) == 'A' + && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'D' + && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'P' + && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'T') + || (ahd_inb_scbram(ahd, SCB_BASE + 0) == 'B' + && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'I' + && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'O' + && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'S') + || (ahd_inb_scbram(ahd, SCB_BASE + 0) == 'A' + && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'S' + && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'P' + && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'I'))) { + uint16_t *sc_data; + int i; + + ahd_set_scbptr(ahd, nvram_scb); + sc_data = (uint16_t *)sc; + for (i = 0; i < 64; i += 2) + *sc_data++ = ahd_inw_scbram(ahd, SCB_BASE+i); + have_seeprom = ahd_verify_cksum(sc); + if (have_seeprom) + ahd->flags |= AHD_SCB_CONFIG_USED; + } + } + +#ifdef AHD_DEBUG + if (have_seeprom != 0 + && (ahd_debug & AHD_DUMP_SEEPROM) != 0) { + uint16_t *sc_data; + int i; + + printk("%s: Seeprom Contents:", ahd_name(ahd)); + sc_data = (uint16_t *)sc; + for (i = 0; i < (sizeof(*sc)); i += 2) + printk("\n\t0x%.4x", sc_data[i]); + printk("\n"); + } +#endif + + if (!have_seeprom) { + if (bootverbose) + printk("%s: No SEEPROM available.\n", ahd_name(ahd)); + ahd->flags |= AHD_USEDEFAULTS; + error = ahd_default_config(ahd); + adapter_control = CFAUTOTERM|CFSEAUTOTERM; + kfree(ahd->seep_config); + ahd->seep_config = NULL; + } else { + error = ahd_parse_cfgdata(ahd, sc); + adapter_control = sc->adapter_control; + } + if (error != 0) + return (error); + + ahd_configure_termination(ahd, adapter_control); + + return (0); +} + +static void +ahd_configure_termination(struct ahd_softc *ahd, u_int adapter_control) +{ + int error; + u_int sxfrctl1; + uint8_t termctl; + uint32_t devconfig; + + devconfig = ahd_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4); + devconfig &= ~STPWLEVEL; + if ((ahd->flags & AHD_STPWLEVEL_A) != 0) + devconfig |= STPWLEVEL; + if (bootverbose) + printk("%s: STPWLEVEL is %s\n", + ahd_name(ahd), (devconfig & STPWLEVEL) ? "on" : "off"); + ahd_pci_write_config(ahd->dev_softc, DEVCONFIG, devconfig, /*bytes*/4); + + /* Make sure current sensing is off. */ + if ((ahd->flags & AHD_CURRENT_SENSING) != 0) { + (void)ahd_write_flexport(ahd, FLXADDR_ROMSTAT_CURSENSECTL, 0); + } + + /* + * Read to sense. Write to set. + */ + error = ahd_read_flexport(ahd, FLXADDR_TERMCTL, &termctl); + if ((adapter_control & CFAUTOTERM) == 0) { + if (bootverbose) + printk("%s: Manual Primary Termination\n", + ahd_name(ahd)); + termctl &= ~(FLX_TERMCTL_ENPRILOW|FLX_TERMCTL_ENPRIHIGH); + if ((adapter_control & CFSTERM) != 0) + termctl |= FLX_TERMCTL_ENPRILOW; + if ((adapter_control & CFWSTERM) != 0) + termctl |= FLX_TERMCTL_ENPRIHIGH; + } else if (error != 0) { + printk("%s: Primary Auto-Term Sensing failed! " + "Using Defaults.\n", ahd_name(ahd)); + termctl = FLX_TERMCTL_ENPRILOW|FLX_TERMCTL_ENPRIHIGH; + } + + if ((adapter_control & CFSEAUTOTERM) == 0) { + if (bootverbose) + printk("%s: Manual Secondary Termination\n", + ahd_name(ahd)); + termctl &= ~(FLX_TERMCTL_ENSECLOW|FLX_TERMCTL_ENSECHIGH); + if ((adapter_control & CFSELOWTERM) != 0) + termctl |= FLX_TERMCTL_ENSECLOW; + if ((adapter_control & CFSEHIGHTERM) != 0) + termctl |= FLX_TERMCTL_ENSECHIGH; + } else if (error != 0) { + printk("%s: Secondary Auto-Term Sensing failed! " + "Using Defaults.\n", ahd_name(ahd)); + termctl |= FLX_TERMCTL_ENSECLOW|FLX_TERMCTL_ENSECHIGH; + } + + /* + * Now set the termination based on what we found. + */ + sxfrctl1 = ahd_inb(ahd, SXFRCTL1) & ~STPWEN; + ahd->flags &= ~AHD_TERM_ENB_A; + if ((termctl & FLX_TERMCTL_ENPRILOW) != 0) { + ahd->flags |= AHD_TERM_ENB_A; + sxfrctl1 |= STPWEN; + } + /* Must set the latch once in order to be effective. */ + ahd_outb(ahd, SXFRCTL1, sxfrctl1|STPWEN); + ahd_outb(ahd, SXFRCTL1, sxfrctl1); + + error = ahd_write_flexport(ahd, FLXADDR_TERMCTL, termctl); + if (error != 0) { + printk("%s: Unable to set termination settings!\n", + ahd_name(ahd)); + } else if (bootverbose) { + printk("%s: Primary High byte termination %sabled\n", + ahd_name(ahd), + (termctl & FLX_TERMCTL_ENPRIHIGH) ? "En" : "Dis"); + + printk("%s: Primary Low byte termination %sabled\n", + ahd_name(ahd), + (termctl & FLX_TERMCTL_ENPRILOW) ? "En" : "Dis"); + + printk("%s: Secondary High byte termination %sabled\n", + ahd_name(ahd), + (termctl & FLX_TERMCTL_ENSECHIGH) ? "En" : "Dis"); + + printk("%s: Secondary Low byte termination %sabled\n", + ahd_name(ahd), + (termctl & FLX_TERMCTL_ENSECLOW) ? "En" : "Dis"); + } + return; +} + +#define DPE 0x80 +#define SSE 0x40 +#define RMA 0x20 +#define RTA 0x10 +#define STA 0x08 +#define DPR 0x01 + +static const char *split_status_source[] = +{ + "DFF0", + "DFF1", + "OVLY", + "CMC", +}; + +static const char *pci_status_source[] = +{ + "DFF0", + "DFF1", + "SG", + "CMC", + "OVLY", + "NONE", + "MSI", + "TARG" +}; + +static const char *split_status_strings[] = +{ + "%s: Received split response in %s.\n", + "%s: Received split completion error message in %s\n", + "%s: Receive overrun in %s\n", + "%s: Count not complete in %s\n", + "%s: Split completion data bucket in %s\n", + "%s: Split completion address error in %s\n", + "%s: Split completion byte count error in %s\n", + "%s: Signaled Target-abort to early terminate a split in %s\n" +}; + +static const char *pci_status_strings[] = +{ + "%s: Data Parity Error has been reported via PERR# in %s\n", + "%s: Target initial wait state error in %s\n", + "%s: Split completion read data parity error in %s\n", + "%s: Split completion address attribute parity error in %s\n", + "%s: Received a Target Abort in %s\n", + "%s: Received a Master Abort in %s\n", + "%s: Signal System Error Detected in %s\n", + "%s: Address or Write Phase Parity Error Detected in %s.\n" +}; + +static void +ahd_pci_intr(struct ahd_softc *ahd) +{ + uint8_t pci_status[8]; + ahd_mode_state saved_modes; + u_int pci_status1; + u_int intstat; + u_int i; + u_int reg; + + intstat = ahd_inb(ahd, INTSTAT); + + if ((intstat & SPLTINT) != 0) + ahd_pci_split_intr(ahd, intstat); + + if ((intstat & PCIINT) == 0) + return; + + printk("%s: PCI error Interrupt\n", ahd_name(ahd)); + saved_modes = ahd_save_modes(ahd); + ahd_dump_card_state(ahd); + ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); + for (i = 0, reg = DF0PCISTAT; i < 8; i++, reg++) { + + if (i == 5) + continue; + pci_status[i] = ahd_inb(ahd, reg); + /* Clear latched errors. So our interrupt deasserts. */ + ahd_outb(ahd, reg, pci_status[i]); + } + + for (i = 0; i < 8; i++) { + u_int bit; + + if (i == 5) + continue; + + for (bit = 0; bit < 8; bit++) { + + if ((pci_status[i] & (0x1 << bit)) != 0) { + const char *s; + + s = pci_status_strings[bit]; + if (i == 7/*TARG*/ && bit == 3) + s = "%s: Signaled Target Abort\n"; + printk(s, ahd_name(ahd), pci_status_source[i]); + } + } + } + pci_status1 = ahd_pci_read_config(ahd->dev_softc, + PCIR_STATUS + 1, /*bytes*/1); + ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, + pci_status1, /*bytes*/1); + ahd_restore_modes(ahd, saved_modes); + ahd_outb(ahd, CLRINT, CLRPCIINT); + ahd_unpause(ahd); +} + +static void +ahd_pci_split_intr(struct ahd_softc *ahd, u_int intstat) +{ + uint8_t split_status[4]; + uint8_t split_status1[4]; + uint8_t sg_split_status[2]; + uint8_t sg_split_status1[2]; + ahd_mode_state saved_modes; + u_int i; + uint16_t pcix_status; + + /* + * Check for splits in all modes. Modes 0 and 1 + * additionally have SG engine splits to look at. + */ + pcix_status = ahd_pci_read_config(ahd->dev_softc, PCIXR_STATUS, + /*bytes*/2); + printk("%s: PCI Split Interrupt - PCI-X status = 0x%x\n", + ahd_name(ahd), pcix_status); + saved_modes = ahd_save_modes(ahd); + for (i = 0; i < 4; i++) { + ahd_set_modes(ahd, i, i); + + split_status[i] = ahd_inb(ahd, DCHSPLTSTAT0); + split_status1[i] = ahd_inb(ahd, DCHSPLTSTAT1); + /* Clear latched errors. So our interrupt deasserts. */ + ahd_outb(ahd, DCHSPLTSTAT0, split_status[i]); + ahd_outb(ahd, DCHSPLTSTAT1, split_status1[i]); + if (i > 1) + continue; + sg_split_status[i] = ahd_inb(ahd, SGSPLTSTAT0); + sg_split_status1[i] = ahd_inb(ahd, SGSPLTSTAT1); + /* Clear latched errors. So our interrupt deasserts. */ + ahd_outb(ahd, SGSPLTSTAT0, sg_split_status[i]); + ahd_outb(ahd, SGSPLTSTAT1, sg_split_status1[i]); + } + + for (i = 0; i < 4; i++) { + u_int bit; + + for (bit = 0; bit < 8; bit++) { + + if ((split_status[i] & (0x1 << bit)) != 0) + printk(split_status_strings[bit], ahd_name(ahd), + split_status_source[i]); + + if (i > 1) + continue; + + if ((sg_split_status[i] & (0x1 << bit)) != 0) + printk(split_status_strings[bit], ahd_name(ahd), "SG"); + } + } + /* + * Clear PCI-X status bits. + */ + ahd_pci_write_config(ahd->dev_softc, PCIXR_STATUS, + pcix_status, /*bytes*/2); + ahd_outb(ahd, CLRINT, CLRSPLTINT); + ahd_restore_modes(ahd, saved_modes); +} + +static int +ahd_aic7901_setup(struct ahd_softc *ahd) +{ + + ahd->chip = AHD_AIC7901; + ahd->features = AHD_AIC7901_FE; + return (ahd_aic790X_setup(ahd)); +} + +static int +ahd_aic7901A_setup(struct ahd_softc *ahd) +{ + + ahd->chip = AHD_AIC7901A; + ahd->features = AHD_AIC7901A_FE; + return (ahd_aic790X_setup(ahd)); +} + +static int +ahd_aic7902_setup(struct ahd_softc *ahd) +{ + ahd->chip = AHD_AIC7902; + ahd->features = AHD_AIC7902_FE; + return (ahd_aic790X_setup(ahd)); +} + +static int +ahd_aic790X_setup(struct ahd_softc *ahd) +{ + ahd_dev_softc_t pci; + u_int rev; + + pci = ahd->dev_softc; + rev = ahd_pci_read_config(pci, PCIR_REVID, /*bytes*/1); + if (rev < ID_AIC7902_PCI_REV_A4) { + printk("%s: Unable to attach to unsupported chip revision %d\n", + ahd_name(ahd), rev); + ahd_pci_write_config(pci, PCIR_COMMAND, 0, /*bytes*/2); + return (ENXIO); + } + ahd->channel = ahd_get_pci_function(pci) + 'A'; + if (rev < ID_AIC7902_PCI_REV_B0) { + /* + * Enable A series workarounds. + */ + ahd->bugs |= AHD_SENT_SCB_UPDATE_BUG|AHD_ABORT_LQI_BUG + | AHD_PKT_BITBUCKET_BUG|AHD_LONG_SETIMO_BUG + | AHD_NLQICRC_DELAYED_BUG|AHD_SCSIRST_BUG + | AHD_LQO_ATNO_BUG|AHD_AUTOFLUSH_BUG + | AHD_CLRLQO_AUTOCLR_BUG|AHD_PCIX_MMAPIO_BUG + | AHD_PCIX_CHIPRST_BUG|AHD_PCIX_SCBRAM_RD_BUG + | AHD_PKTIZED_STATUS_BUG|AHD_PKT_LUN_BUG + | AHD_MDFF_WSCBPTR_BUG|AHD_REG_SLOW_SETTLE_BUG + | AHD_SET_MODE_BUG|AHD_BUSFREEREV_BUG + | AHD_NONPACKFIFO_BUG|AHD_PACED_NEGTABLE_BUG + | AHD_FAINT_LED_BUG; + + /* + * IO Cell parameter setup. + */ + AHD_SET_PRECOMP(ahd, AHD_PRECOMP_CUTBACK_29); + + if ((ahd->flags & AHD_HP_BOARD) == 0) + AHD_SET_SLEWRATE(ahd, AHD_SLEWRATE_DEF_REVA); + } else { + /* This is revision B and newer. */ + extern uint32_t aic79xx_slowcrc; + u_int devconfig1; + + ahd->features |= AHD_RTI|AHD_NEW_IOCELL_OPTS + | AHD_NEW_DFCNTRL_OPTS|AHD_FAST_CDB_DELIVERY + | AHD_BUSFREEREV_BUG; + ahd->bugs |= AHD_LQOOVERRUN_BUG|AHD_EARLY_REQ_BUG; + + /* If the user requested that the SLOWCRC bit to be set. */ + if (aic79xx_slowcrc) + ahd->features |= AHD_AIC79XXB_SLOWCRC; + + /* + * Some issues have been resolved in the 7901B. + */ + if ((ahd->features & AHD_MULTI_FUNC) != 0) + ahd->bugs |= AHD_INTCOLLISION_BUG|AHD_ABORT_LQI_BUG; + + /* + * IO Cell parameter setup. + */ + AHD_SET_PRECOMP(ahd, AHD_PRECOMP_CUTBACK_29); + AHD_SET_SLEWRATE(ahd, AHD_SLEWRATE_DEF_REVB); + AHD_SET_AMPLITUDE(ahd, AHD_AMPLITUDE_DEF); + + /* + * Set the PREQDIS bit for H2B which disables some workaround + * that doesn't work on regular PCI busses. + * XXX - Find out exactly what this does from the hardware + * folks! + */ + devconfig1 = ahd_pci_read_config(pci, DEVCONFIG1, /*bytes*/1); + ahd_pci_write_config(pci, DEVCONFIG1, + devconfig1|PREQDIS, /*bytes*/1); + devconfig1 = ahd_pci_read_config(pci, DEVCONFIG1, /*bytes*/1); + } + + return (0); +} diff --git a/drivers/scsi/aic7xxx/aic79xx_pci.h b/drivers/scsi/aic7xxx/aic79xx_pci.h new file mode 100644 index 000000000..16b7c70a6 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx_pci.h @@ -0,0 +1,72 @@ +/* + * Adaptec AIC79xx device driver for Linux. + * + * Copyright (c) 2000-2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id$ + * + */ +#ifndef _AIC79XX_PCI_H_ +#define _AIC79XX_PCI_H_ + +#define ID_ALL_MASK 0xFFFFFFFFFFFFFFFFull +#define ID_ALL_IROC_MASK 0xFF7FFFFFFFFFFFFFull +#define ID_DEV_VENDOR_MASK 0xFFFFFFFF00000000ull +#define ID_9005_GENERIC_MASK 0xFFF0FFFF00000000ull +#define ID_9005_GENERIC_IROC_MASK 0xFF70FFFF00000000ull + +#define ID_AIC7901 0x800F9005FFFF9005ull +#define ID_AHA_29320A 0x8000900500609005ull +#define ID_AHA_29320ALP 0x8017900500449005ull +#define ID_AHA_29320LPE 0x8017900500459005ull + +#define ID_AIC7901A 0x801E9005FFFF9005ull +#define ID_AHA_29320LP 0x8014900500449005ull + +#define ID_AIC7902 0x801F9005FFFF9005ull +#define ID_AIC7902_B 0x801D9005FFFF9005ull +#define ID_AHA_39320 0x8010900500409005ull +#define ID_AHA_29320 0x8012900500429005ull +#define ID_AHA_29320B 0x8013900500439005ull +#define ID_AHA_39320_B 0x8015900500409005ull +#define ID_AHA_39320_B_DELL 0x8015900501681028ull +#define ID_AHA_39320A 0x8016900500409005ull +#define ID_AHA_39320D 0x8011900500419005ull +#define ID_AHA_39320D_B 0x801C900500419005ull +#define ID_AHA_39320D_HP 0x8011900500AC0E11ull +#define ID_AHA_39320D_B_HP 0x801C900500AC0E11ull + +#endif /* _AIC79XX_PCI_H_ */ diff --git a/drivers/scsi/aic7xxx/aic79xx_proc.c b/drivers/scsi/aic7xxx/aic79xx_proc.c new file mode 100644 index 000000000..add2da581 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx_proc.c @@ -0,0 +1,315 @@ +/* + * Copyright (c) 2000-2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * String handling code courtesy of Gerard Roudier's <groudier@club-internet.fr> + * sym driver. + * + * $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic79xx_proc.c#19 $ + */ +#include "aic79xx_osm.h" +#include "aic79xx_inline.h" + +static void ahd_dump_target_state(struct ahd_softc *ahd, + struct seq_file *m, + u_int our_id, char channel, + u_int target_id); +static void ahd_dump_device_state(struct seq_file *m, + struct scsi_device *sdev); + +/* + * Table of syncrates that don't follow the "divisible by 4" + * rule. This table will be expanded in future SCSI specs. + */ +static const struct { + u_int period_factor; + u_int period; /* in 100ths of ns */ +} scsi_syncrates[] = { + { 0x08, 625 }, /* FAST-160 */ + { 0x09, 1250 }, /* FAST-80 */ + { 0x0a, 2500 }, /* FAST-40 40MHz */ + { 0x0b, 3030 }, /* FAST-40 33MHz */ + { 0x0c, 5000 } /* FAST-20 */ +}; + +/* + * Return the frequency in kHz corresponding to the given + * sync period factor. + */ +static u_int +ahd_calc_syncsrate(u_int period_factor) +{ + int i; + + /* See if the period is in the "exception" table */ + for (i = 0; i < ARRAY_SIZE(scsi_syncrates); i++) { + + if (period_factor == scsi_syncrates[i].period_factor) { + /* Period in kHz */ + return (100000000 / scsi_syncrates[i].period); + } + } + + /* + * Wasn't in the table, so use the standard + * 4 times conversion. + */ + return (10000000 / (period_factor * 4 * 10)); +} + +static void +ahd_format_transinfo(struct seq_file *m, struct ahd_transinfo *tinfo) +{ + u_int speed; + u_int freq; + u_int mb; + + if (tinfo->period == AHD_PERIOD_UNKNOWN) { + seq_puts(m, "Renegotiation Pending\n"); + return; + } + speed = 3300; + freq = 0; + if (tinfo->offset != 0) { + freq = ahd_calc_syncsrate(tinfo->period); + speed = freq; + } + speed *= (0x01 << tinfo->width); + mb = speed / 1000; + if (mb > 0) + seq_printf(m, "%d.%03dMB/s transfers", mb, speed % 1000); + else + seq_printf(m, "%dKB/s transfers", speed); + + if (freq != 0) { + int printed_options; + + printed_options = 0; + seq_printf(m, " (%d.%03dMHz", freq / 1000, freq % 1000); + if ((tinfo->ppr_options & MSG_EXT_PPR_RD_STRM) != 0) { + seq_puts(m, " RDSTRM"); + printed_options++; + } + if ((tinfo->ppr_options & MSG_EXT_PPR_DT_REQ) != 0) { + seq_puts(m, printed_options ? "|DT" : " DT"); + printed_options++; + } + if ((tinfo->ppr_options & MSG_EXT_PPR_IU_REQ) != 0) { + seq_puts(m, printed_options ? "|IU" : " IU"); + printed_options++; + } + if ((tinfo->ppr_options & MSG_EXT_PPR_RTI) != 0) { + seq_puts(m, printed_options ? "|RTI" : " RTI"); + printed_options++; + } + if ((tinfo->ppr_options & MSG_EXT_PPR_QAS_REQ) != 0) { + seq_puts(m, printed_options ? "|QAS" : " QAS"); + printed_options++; + } + } + + if (tinfo->width > 0) { + if (freq != 0) { + seq_puts(m, ", "); + } else { + seq_puts(m, " ("); + } + seq_printf(m, "%dbit)", 8 * (0x01 << tinfo->width)); + } else if (freq != 0) { + seq_putc(m, ')'); + } + seq_putc(m, '\n'); +} + +static void +ahd_dump_target_state(struct ahd_softc *ahd, struct seq_file *m, + u_int our_id, char channel, u_int target_id) +{ + struct scsi_target *starget; + struct ahd_initiator_tinfo *tinfo; + struct ahd_tmode_tstate *tstate; + int lun; + + tinfo = ahd_fetch_transinfo(ahd, channel, our_id, + target_id, &tstate); + seq_printf(m, "Target %d Negotiation Settings\n", target_id); + seq_puts(m, "\tUser: "); + ahd_format_transinfo(m, &tinfo->user); + starget = ahd->platform_data->starget[target_id]; + if (starget == NULL) + return; + + seq_puts(m, "\tGoal: "); + ahd_format_transinfo(m, &tinfo->goal); + seq_puts(m, "\tCurr: "); + ahd_format_transinfo(m, &tinfo->curr); + + for (lun = 0; lun < AHD_NUM_LUNS; lun++) { + struct scsi_device *dev; + + dev = scsi_device_lookup_by_target(starget, lun); + + if (dev == NULL) + continue; + + ahd_dump_device_state(m, dev); + } +} + +static void +ahd_dump_device_state(struct seq_file *m, struct scsi_device *sdev) +{ + struct ahd_linux_device *dev = scsi_transport_device_data(sdev); + + seq_printf(m, "\tChannel %c Target %d Lun %d Settings\n", + sdev->sdev_target->channel + 'A', + sdev->sdev_target->id, (u8)sdev->lun); + + seq_printf(m, "\t\tCommands Queued %ld\n", dev->commands_issued); + seq_printf(m, "\t\tCommands Active %d\n", dev->active); + seq_printf(m, "\t\tCommand Openings %d\n", dev->openings); + seq_printf(m, "\t\tMax Tagged Openings %d\n", dev->maxtags); + seq_printf(m, "\t\tDevice Queue Frozen Count %d\n", dev->qfrozen); +} + +int +ahd_proc_write_seeprom(struct Scsi_Host *shost, char *buffer, int length) +{ + struct ahd_softc *ahd = *(struct ahd_softc **)shost->hostdata; + ahd_mode_state saved_modes; + int have_seeprom; + u_long s; + int paused; + int written; + + /* Default to failure. */ + written = -EINVAL; + ahd_lock(ahd, &s); + paused = ahd_is_paused(ahd); + if (!paused) + ahd_pause(ahd); + + saved_modes = ahd_save_modes(ahd); + ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); + if (length != sizeof(struct seeprom_config)) { + printk("ahd_proc_write_seeprom: incorrect buffer size\n"); + goto done; + } + + have_seeprom = ahd_verify_cksum((struct seeprom_config*)buffer); + if (have_seeprom == 0) { + printk("ahd_proc_write_seeprom: cksum verification failed\n"); + goto done; + } + + have_seeprom = ahd_acquire_seeprom(ahd); + if (!have_seeprom) { + printk("ahd_proc_write_seeprom: No Serial EEPROM\n"); + goto done; + } else { + u_int start_addr; + + if (ahd->seep_config == NULL) { + ahd->seep_config = kmalloc(sizeof(*ahd->seep_config), GFP_ATOMIC); + if (ahd->seep_config == NULL) { + printk("aic79xx: Unable to allocate serial " + "eeprom buffer. Write failing\n"); + goto done; + } + } + printk("aic79xx: Writing Serial EEPROM\n"); + start_addr = 32 * (ahd->channel - 'A'); + ahd_write_seeprom(ahd, (u_int16_t *)buffer, start_addr, + sizeof(struct seeprom_config)/2); + ahd_read_seeprom(ahd, (uint16_t *)ahd->seep_config, + start_addr, sizeof(struct seeprom_config)/2, + /*ByteStream*/FALSE); + ahd_release_seeprom(ahd); + written = length; + } + +done: + ahd_restore_modes(ahd, saved_modes); + if (!paused) + ahd_unpause(ahd); + ahd_unlock(ahd, &s); + return (written); +} +/* + * Return information to handle /proc support for the driver. + */ +int +ahd_linux_show_info(struct seq_file *m, struct Scsi_Host *shost) +{ + struct ahd_softc *ahd = *(struct ahd_softc **)shost->hostdata; + char ahd_info[256]; + u_int max_targ; + u_int i; + + seq_printf(m, "Adaptec AIC79xx driver version: %s\n", + AIC79XX_DRIVER_VERSION); + seq_printf(m, "%s\n", ahd->description); + ahd_controller_info(ahd, ahd_info); + seq_printf(m, "%s\n", ahd_info); + seq_printf(m, "Allocated SCBs: %d, SG List Length: %d\n\n", + ahd->scb_data.numscbs, AHD_NSEG); + + max_targ = 16; + + if (ahd->seep_config == NULL) + seq_puts(m, "No Serial EEPROM\n"); + else { + seq_puts(m, "Serial EEPROM:\n"); + for (i = 0; i < sizeof(*ahd->seep_config)/2; i++) { + if (((i % 8) == 0) && (i != 0)) { + seq_putc(m, '\n'); + } + seq_printf(m, "0x%.4x ", + ((uint16_t*)ahd->seep_config)[i]); + } + seq_putc(m, '\n'); + } + seq_putc(m, '\n'); + + if ((ahd->features & AHD_WIDE) == 0) + max_targ = 8; + + for (i = 0; i < max_targ; i++) { + + ahd_dump_target_state(ahd, m, ahd->our_id, 'A', + /*target_id*/i); + } + return 0; +} diff --git a/drivers/scsi/aic7xxx/aic79xx_reg.h_shipped b/drivers/scsi/aic7xxx/aic79xx_reg.h_shipped new file mode 100644 index 000000000..ddcd5a770 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx_reg.h_shipped @@ -0,0 +1,1810 @@ +/* + * DO NOT EDIT - This file is automatically generated + * from the following source files: + * + * $Id: //depot/aic7xxx/aic7xxx/aic79xx.seq#120 $ + * $Id: //depot/aic7xxx/aic7xxx/aic79xx.reg#77 $ + */ +typedef int (ahd_reg_print_t)(u_int, u_int *, u_int); +typedef struct ahd_reg_parse_entry { + char *name; + uint8_t value; + uint8_t mask; +} ahd_reg_parse_entry_t; + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_intstat_print; +#else +#define ahd_intstat_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "INTSTAT", 0x01, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_hs_mailbox_print; +#else +#define ahd_hs_mailbox_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "HS_MAILBOX", 0x0b, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_seqintstat_print; +#else +#define ahd_seqintstat_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SEQINTSTAT", 0x0c, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_intctl_print; +#else +#define ahd_intctl_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "INTCTL", 0x18, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_dfcntrl_print; +#else +#define ahd_dfcntrl_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "DFCNTRL", 0x19, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_dfstatus_print; +#else +#define ahd_dfstatus_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "DFSTATUS", 0x1a, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_sg_cache_shadow_print; +#else +#define ahd_sg_cache_shadow_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SG_CACHE_SHADOW", 0x1b, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_scsiseq0_print; +#else +#define ahd_scsiseq0_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SCSISEQ0", 0x3a, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_scsiseq1_print; +#else +#define ahd_scsiseq1_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SCSISEQ1", 0x3b, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_dffstat_print; +#else +#define ahd_dffstat_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "DFFSTAT", 0x3f, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_scsisigi_print; +#else +#define ahd_scsisigi_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SCSISIGI", 0x41, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_scsiphase_print; +#else +#define ahd_scsiphase_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SCSIPHASE", 0x42, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_scsibus_print; +#else +#define ahd_scsibus_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SCSIBUS", 0x46, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_selid_print; +#else +#define ahd_selid_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SELID", 0x49, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_simode0_print; +#else +#define ahd_simode0_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SIMODE0", 0x4b, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_sstat0_print; +#else +#define ahd_sstat0_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SSTAT0", 0x4b, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_sstat1_print; +#else +#define ahd_sstat1_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SSTAT1", 0x4c, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_sstat2_print; +#else +#define ahd_sstat2_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SSTAT2", 0x4d, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_perrdiag_print; +#else +#define ahd_perrdiag_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "PERRDIAG", 0x4e, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_soffcnt_print; +#else +#define ahd_soffcnt_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SOFFCNT", 0x4f, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_lqistat0_print; +#else +#define ahd_lqistat0_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "LQISTAT0", 0x50, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_lqistat1_print; +#else +#define ahd_lqistat1_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "LQISTAT1", 0x51, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_lqistat2_print; +#else +#define ahd_lqistat2_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "LQISTAT2", 0x52, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_sstat3_print; +#else +#define ahd_sstat3_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SSTAT3", 0x53, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_lqostat0_print; +#else +#define ahd_lqostat0_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "LQOSTAT0", 0x54, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_lqostat1_print; +#else +#define ahd_lqostat1_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "LQOSTAT1", 0x55, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_lqostat2_print; +#else +#define ahd_lqostat2_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "LQOSTAT2", 0x56, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_simode1_print; +#else +#define ahd_simode1_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SIMODE1", 0x57, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_dffsxfrctl_print; +#else +#define ahd_dffsxfrctl_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "DFFSXFRCTL", 0x5a, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_seqintsrc_print; +#else +#define ahd_seqintsrc_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SEQINTSRC", 0x5b, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_seqimode_print; +#else +#define ahd_seqimode_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SEQIMODE", 0x5c, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_mdffstat_print; +#else +#define ahd_mdffstat_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "MDFFSTAT", 0x5d, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_seloid_print; +#else +#define ahd_seloid_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SELOID", 0x6b, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_sg_state_print; +#else +#define ahd_sg_state_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SG_STATE", 0xa6, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_ccscbctl_print; +#else +#define ahd_ccscbctl_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "CCSCBCTL", 0xad, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_ccsgctl_print; +#else +#define ahd_ccsgctl_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "CCSGCTL", 0xad, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_seqctl0_print; +#else +#define ahd_seqctl0_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SEQCTL0", 0xd6, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_seqintctl_print; +#else +#define ahd_seqintctl_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SEQINTCTL", 0xd9, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_sram_base_print; +#else +#define ahd_sram_base_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SRAM_BASE", 0x100, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_qfreeze_count_print; +#else +#define ahd_qfreeze_count_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "QFREEZE_COUNT", 0x132, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_kernel_qfreeze_count_print; +#else +#define ahd_kernel_qfreeze_count_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "KERNEL_QFREEZE_COUNT", 0x134, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_saved_mode_print; +#else +#define ahd_saved_mode_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SAVED_MODE", 0x136, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_seq_flags_print; +#else +#define ahd_seq_flags_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SEQ_FLAGS", 0x139, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_lastphase_print; +#else +#define ahd_lastphase_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "LASTPHASE", 0x13c, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_seq_flags2_print; +#else +#define ahd_seq_flags2_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SEQ_FLAGS2", 0x14d, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_mk_message_scb_print; +#else +#define ahd_mk_message_scb_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "MK_MESSAGE_SCB", 0x160, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_mk_message_scsiid_print; +#else +#define ahd_mk_message_scsiid_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "MK_MESSAGE_SCSIID", 0x162, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_scb_base_print; +#else +#define ahd_scb_base_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SCB_BASE", 0x180, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_scb_control_print; +#else +#define ahd_scb_control_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SCB_CONTROL", 0x192, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahd_reg_print_t ahd_scb_scsiid_print; +#else +#define ahd_scb_scsiid_print(regvalue, cur_col, wrap) \ + ahd_print_register(NULL, 0, "SCB_SCSIID", 0x193, regvalue, cur_col, wrap) +#endif + + +#define MODE_PTR 0x00 +#define DST_MODE 0x70 +#define SRC_MODE 0x07 + +#define INTSTAT 0x01 +#define INT_PEND 0xff +#define HWERRINT 0x80 +#define BRKADRINT 0x40 +#define SWTMINT 0x20 +#define PCIINT 0x10 +#define SCSIINT 0x08 +#define SEQINT 0x04 +#define CMDCMPLT 0x02 +#define SPLTINT 0x01 + +#define SEQINTCODE 0x02 +#define BAD_SCB_STATUS 0x1a +#define SAW_HWERR 0x19 +#define TRACEPOINT3 0x18 +#define TRACEPOINT2 0x17 +#define TRACEPOINT1 0x16 +#define TRACEPOINT0 0x15 +#define TASKMGMT_CMD_CMPLT_OKAY 0x14 +#define TASKMGMT_FUNC_COMPLETE 0x13 +#define ENTERING_NONPACK 0x12 +#define CFG4OVERRUN 0x11 +#define STATUS_OVERRUN 0x10 +#define CFG4ISTAT_INTR 0x0f +#define INVALID_SEQINT 0x0e +#define ILLEGAL_PHASE 0x0d +#define DUMP_CARD_STATE 0x0c +#define MISSED_BUSFREE 0x0b +#define MKMSG_FAILED 0x0a +#define DATA_OVERRUN 0x09 +#define BAD_STATUS 0x08 +#define HOST_MSG_LOOP 0x07 +#define PDATA_REINIT 0x06 +#define IGN_WIDE_RES 0x05 +#define NO_MATCH 0x04 +#define PROTO_VIOLATION 0x03 +#define SEND_REJECT 0x02 +#define BAD_PHASE 0x01 +#define NO_SEQINT 0x00 + +#define CLRINT 0x03 +#define CLRHWERRINT 0x80 +#define CLRBRKADRINT 0x40 +#define CLRSWTMINT 0x20 +#define CLRPCIINT 0x10 +#define CLRSCSIINT 0x08 +#define CLRSEQINT 0x04 +#define CLRCMDINT 0x02 +#define CLRSPLTINT 0x01 + +#define CLRERR 0x04 +#define CLRCIOPARERR 0x80 +#define CLRCIOACCESFAIL 0x40 +#define CLRMPARERR 0x20 +#define CLRDPARERR 0x10 +#define CLRSQPARERR 0x08 +#define CLRILLOPCODE 0x04 +#define CLRDSCTMOUT 0x02 + +#define ERROR 0x04 +#define CIOPARERR 0x80 +#define CIOACCESFAIL 0x40 +#define MPARERR 0x20 +#define DPARERR 0x10 +#define SQPARERR 0x08 +#define ILLOPCODE 0x04 +#define DSCTMOUT 0x02 + +#define HCNTRL 0x05 +#define SEQ_RESET 0x80 +#define POWRDN 0x40 +#define SWINT 0x10 +#define SWTIMER_START_B 0x08 +#define PAUSE 0x04 +#define INTEN 0x02 +#define CHIPRST 0x01 +#define CHIPRSTACK 0x01 + +#define HNSCB_QOFF 0x06 + +#define HESCB_QOFF 0x08 + +#define HS_MAILBOX 0x0b +#define HOST_TQINPOS 0x80 +#define ENINT_COALESCE 0x40 + +#define SEQINTSTAT 0x0c +#define SEQ_SWTMRTO 0x10 +#define SEQ_SEQINT 0x08 +#define SEQ_SCSIINT 0x04 +#define SEQ_PCIINT 0x02 +#define SEQ_SPLTINT 0x01 + +#define CLRSEQINTSTAT 0x0c +#define CLRSEQ_SWTMRTO 0x10 +#define CLRSEQ_SEQINT 0x08 +#define CLRSEQ_SCSIINT 0x04 +#define CLRSEQ_PCIINT 0x02 +#define CLRSEQ_SPLTINT 0x01 + +#define SWTIMER 0x0e + +#define SNSCB_QOFF 0x10 + +#define SESCB_QOFF 0x12 + +#define SDSCB_QOFF 0x14 + +#define QOFF_CTLSTA 0x16 +#define EMPTY_SCB_AVAIL 0x80 +#define NEW_SCB_AVAIL 0x40 +#define SDSCB_ROLLOVR 0x20 +#define HS_MAILBOX_ACT 0x10 +#define SCB_QSIZE 0x0f +#define SCB_QSIZE_16384 0x0c +#define SCB_QSIZE_8192 0x0b +#define SCB_QSIZE_4096 0x0a +#define SCB_QSIZE_2048 0x09 +#define SCB_QSIZE_1024 0x08 +#define SCB_QSIZE_512 0x07 +#define SCB_QSIZE_256 0x06 +#define SCB_QSIZE_128 0x05 +#define SCB_QSIZE_64 0x04 +#define SCB_QSIZE_32 0x03 +#define SCB_QSIZE_16 0x02 +#define SCB_QSIZE_8 0x01 +#define SCB_QSIZE_4 0x00 + +#define INTCTL 0x18 +#define SWTMINTMASK 0x80 +#define SWTMINTEN 0x40 +#define SWTIMER_START 0x20 +#define AUTOCLRCMDINT 0x10 +#define PCIINTEN 0x08 +#define SCSIINTEN 0x04 +#define SEQINTEN 0x02 +#define SPLTINTEN 0x01 + +#define DFCNTRL 0x19 +#define SCSIENWRDIS 0x40 +#define SCSIENACK 0x20 +#define DIRECTIONACK 0x04 +#define FIFOFLUSHACK 0x02 +#define DIRECTIONEN 0x01 + +#define DSCOMMAND0 0x19 +#define CACHETHEN 0x80 +#define DPARCKEN 0x40 +#define MPARCKEN 0x20 +#define EXTREQLCK 0x10 +#define DISABLE_TWATE 0x02 +#define CIOPARCKEN 0x01 + +#define DFSTATUS 0x1a +#define PRELOAD_AVAIL 0x80 +#define PKT_PRELOAD_AVAIL 0x40 +#define MREQPEND 0x10 +#define HDONE 0x08 +#define DFTHRESH 0x04 +#define FIFOFULL 0x02 +#define FIFOEMP 0x01 + +#define ARBCTL 0x1b +#define RESET_HARB 0x80 +#define RETRY_SWEN 0x08 +#define USE_TIME 0x07 + +#define SG_CACHE_SHADOW 0x1b +#define ODD_SEG 0x04 +#define LAST_SEG 0x02 +#define LAST_SEG_DONE 0x01 + +#define SG_CACHE_PRE 0x1b + +#define TYPEPTR 0x20 + +#define LQIN 0x20 + +#define TAGPTR 0x21 + +#define LUNPTR 0x22 + +#define DATALENPTR 0x23 + +#define STATLENPTR 0x24 + +#define CMDLENPTR 0x25 + +#define ATTRPTR 0x26 + +#define FLAGPTR 0x27 + +#define CMDPTR 0x28 + +#define QNEXTPTR 0x29 + +#define IDPTR 0x2a + +#define ABRTBYTEPTR 0x2b + +#define ABRTBITPTR 0x2c + +#define MAXCMDBYTES 0x2d + +#define MAXCMD2RCV 0x2e + +#define SHORTTHRESH 0x2f + +#define LUNLEN 0x30 +#define TLUNLEN 0xf0 +#define ILUNLEN 0x0f + +#define CDBLIMIT 0x31 + +#define MAXCMD 0x32 + +#define MAXCMDCNT 0x33 + +#define LQRSVD01 0x34 + +#define LQRSVD16 0x35 + +#define LQRSVD17 0x36 + +#define CMDRSVD0 0x37 + +#define LQCTL0 0x38 +#define LQITARGCLT 0xc0 +#define LQIINITGCLT 0x30 +#define LQ0TARGCLT 0x0c +#define LQ0INITGCLT 0x03 + +#define LQCTL1 0x38 +#define PCI2PCI 0x04 +#define SINGLECMD 0x02 +#define ABORTPENDING 0x01 + +#define LQCTL2 0x39 +#define LQIRETRY 0x80 +#define LQICONTINUE 0x40 +#define LQITOIDLE 0x20 +#define LQIPAUSE 0x10 +#define LQORETRY 0x08 +#define LQOCONTINUE 0x04 +#define LQOTOIDLE 0x02 +#define LQOPAUSE 0x01 + +#define SCSBIST0 0x39 +#define GSBISTERR 0x40 +#define GSBISTDONE 0x20 +#define GSBISTRUN 0x10 +#define OSBISTERR 0x04 +#define OSBISTDONE 0x02 +#define OSBISTRUN 0x01 + +#define SCSISEQ0 0x3a +#define TEMODEO 0x80 +#define ENSELO 0x40 +#define ENARBO 0x20 +#define FORCEBUSFREE 0x10 +#define SCSIRSTO 0x01 + +#define SCSBIST1 0x3a +#define NTBISTERR 0x04 +#define NTBISTDONE 0x02 +#define NTBISTRUN 0x01 + +#define SCSISEQ1 0x3b + +#define BUSINITID 0x3c + +#define SXFRCTL0 0x3c +#define DFON 0x80 +#define DFPEXP 0x40 +#define BIOSCANCELEN 0x10 +#define SPIOEN 0x08 + +#define DLCOUNT 0x3c + +#define SXFRCTL1 0x3d +#define BITBUCKET 0x80 +#define ENSACHK 0x40 +#define ENSPCHK 0x20 +#define STIMESEL 0x18 +#define ENSTIMER 0x04 +#define ACTNEGEN 0x02 +#define STPWEN 0x01 + +#define BUSTARGID 0x3e + +#define SXFRCTL2 0x3e +#define AUTORSTDIS 0x10 +#define CMDDMAEN 0x08 +#define ASU 0x07 + +#define DFFSTAT 0x3f +#define CURRFIFO 0x03 +#define FIFO1FREE 0x20 +#define FIFO0FREE 0x10 +#define CURRFIFO_NONE 0x03 +#define CURRFIFO_1 0x01 +#define CURRFIFO_0 0x00 + +#define MULTARGID 0x40 + +#define SCSISIGO 0x40 +#define CDO 0x80 +#define IOO 0x40 +#define MSGO 0x20 +#define ATNO 0x10 +#define SELO 0x08 +#define BSYO 0x04 +#define REQO 0x02 +#define ACKO 0x01 + +#define SCSISIGI 0x41 +#define ATNI 0x10 +#define SELI 0x08 +#define BSYI 0x04 +#define REQI 0x02 +#define ACKI 0x01 + +#define SCSIPHASE 0x42 +#define STATUS_PHASE 0x20 +#define COMMAND_PHASE 0x10 +#define MSG_IN_PHASE 0x08 +#define MSG_OUT_PHASE 0x04 +#define DATA_PHASE_MASK 0x03 +#define DATA_IN_PHASE 0x02 +#define DATA_OUT_PHASE 0x01 + +#define SCSIDAT0_IMG 0x43 + +#define SCSIDAT 0x44 + +#define SCSIBUS 0x46 + +#define TARGIDIN 0x48 +#define CLKOUT 0x80 +#define TARGID 0x0f + +#define SELID 0x49 +#define SELID_MASK 0xf0 +#define ONEBIT 0x08 + +#define OPTIONMODE 0x4a +#define OPTIONMODE_DEFAULTS 0x02 +#define BIOSCANCTL 0x80 +#define AUTOACKEN 0x40 +#define BIASCANCTL 0x20 +#define BUSFREEREV 0x10 +#define ENDGFORMCHK 0x04 +#define AUTO_MSGOUT_DE 0x02 + +#define SBLKCTL 0x4a +#define DIAGLEDEN 0x80 +#define DIAGLEDON 0x40 +#define ENAB40 0x08 +#define ENAB20 0x04 +#define SELWIDE 0x02 + +#define SIMODE0 0x4b +#define ENSELDO 0x40 +#define ENSELDI 0x20 +#define ENSELINGO 0x10 +#define ENIOERR 0x08 +#define ENOVERRUN 0x04 +#define ENSPIORDY 0x02 +#define ENARBDO 0x01 + +#define SSTAT0 0x4b +#define TARGET 0x80 +#define SELDO 0x40 +#define SELDI 0x20 +#define SELINGO 0x10 +#define IOERR 0x08 +#define OVERRUN 0x04 +#define SPIORDY 0x02 +#define ARBDO 0x01 + +#define CLRSINT0 0x4b +#define CLRSELDO 0x40 +#define CLRSELDI 0x20 +#define CLRSELINGO 0x10 +#define CLRIOERR 0x08 +#define CLROVERRUN 0x04 +#define CLRSPIORDY 0x02 +#define CLRARBDO 0x01 + +#define SSTAT1 0x4c +#define SELTO 0x80 +#define ATNTARG 0x40 +#define SCSIRSTI 0x20 +#define PHASEMIS 0x10 +#define BUSFREE 0x08 +#define SCSIPERR 0x04 +#define STRB2FAST 0x02 +#define REQINIT 0x01 + +#define CLRSINT1 0x4c +#define CLRSELTIMEO 0x80 +#define CLRATNO 0x40 +#define CLRSCSIRSTI 0x20 +#define CLRBUSFREE 0x08 +#define CLRSCSIPERR 0x04 +#define CLRSTRB2FAST 0x02 +#define CLRREQINIT 0x01 + +#define SIMODE2 0x4d +#define ENWIDE_RES 0x04 +#define ENSDONE 0x02 +#define ENDMADONE 0x01 + +#define SSTAT2 0x4d +#define BUSFREETIME 0xc0 +#define NONPACKREQ 0x20 +#define EXP_ACTIVE 0x10 +#define BSYX 0x08 +#define WIDE_RES 0x04 +#define SDONE 0x02 +#define DMADONE 0x01 +#define BUSFREE_DFF1 0xc0 +#define BUSFREE_DFF0 0x80 +#define BUSFREE_LQO 0x40 + +#define CLRSINT2 0x4d +#define CLRNONPACKREQ 0x20 +#define CLRWIDE_RES 0x04 +#define CLRSDONE 0x02 +#define CLRDMADONE 0x01 + +#define PERRDIAG 0x4e +#define HIZERO 0x80 +#define HIPERR 0x40 +#define PREVPHASE 0x20 +#define PARITYERR 0x10 +#define AIPERR 0x08 +#define CRCERR 0x04 +#define DGFORMERR 0x02 +#define DTERR 0x01 + +#define LQISTATE 0x4e + +#define LQOSTATE 0x4f + +#define SOFFCNT 0x4f + +#define LQISTAT0 0x50 +#define LQIATNQAS 0x20 +#define LQICRCT1 0x10 +#define LQICRCT2 0x08 +#define LQIBADLQT 0x04 +#define LQIATNLQ 0x02 +#define LQIATNCMD 0x01 + +#define LQIMODE0 0x50 +#define ENLQIATNQASK 0x20 +#define ENLQICRCT1 0x10 +#define ENLQICRCT2 0x08 +#define ENLQIBADLQT 0x04 +#define ENLQIATNLQ 0x02 +#define ENLQIATNCMD 0x01 + +#define CLRLQIINT0 0x50 +#define CLRLQIATNQAS 0x20 +#define CLRLQICRCT1 0x10 +#define CLRLQICRCT2 0x08 +#define CLRLQIBADLQT 0x04 +#define CLRLQIATNLQ 0x02 +#define CLRLQIATNCMD 0x01 + +#define LQIMODE1 0x51 +#define ENLQIPHASE_LQ 0x80 +#define ENLQIPHASE_NLQ 0x40 +#define ENLIQABORT 0x20 +#define ENLQICRCI_LQ 0x10 +#define ENLQICRCI_NLQ 0x08 +#define ENLQIBADLQI 0x04 +#define ENLQIOVERI_LQ 0x02 +#define ENLQIOVERI_NLQ 0x01 + +#define LQISTAT1 0x51 +#define LQIPHASE_LQ 0x80 +#define LQIPHASE_NLQ 0x40 +#define LQIABORT 0x20 +#define LQICRCI_LQ 0x10 +#define LQICRCI_NLQ 0x08 +#define LQIBADLQI 0x04 +#define LQIOVERI_LQ 0x02 +#define LQIOVERI_NLQ 0x01 + +#define CLRLQIINT1 0x51 +#define CLRLQIPHASE_LQ 0x80 +#define CLRLQIPHASE_NLQ 0x40 +#define CLRLIQABORT 0x20 +#define CLRLQICRCI_LQ 0x10 +#define CLRLQICRCI_NLQ 0x08 +#define CLRLQIBADLQI 0x04 +#define CLRLQIOVERI_LQ 0x02 +#define CLRLQIOVERI_NLQ 0x01 + +#define LQISTAT2 0x52 +#define PACKETIZED 0x80 +#define LQIPHASE_OUTPKT 0x40 +#define LQIWORKONLQ 0x20 +#define LQIWAITFIFO 0x10 +#define LQISTOPPKT 0x08 +#define LQISTOPLQ 0x04 +#define LQISTOPCMD 0x02 +#define LQIGSAVAIL 0x01 + +#define SIMODE3 0x53 +#define ENNTRAMPERR 0x02 +#define ENOSRAMPERR 0x01 + +#define SSTAT3 0x53 +#define NTRAMPERR 0x02 +#define OSRAMPERR 0x01 + +#define CLRSINT3 0x53 +#define CLRNTRAMPERR 0x02 +#define CLROSRAMPERR 0x01 + +#define CLRLQOINT0 0x54 +#define CLRLQOTARGSCBPERR 0x10 +#define CLRLQOSTOPT2 0x08 +#define CLRLQOATNLQ 0x04 +#define CLRLQOATNPKT 0x02 +#define CLRLQOTCRC 0x01 + +#define LQOSTAT0 0x54 +#define LQOTARGSCBPERR 0x10 +#define LQOSTOPT2 0x08 +#define LQOATNLQ 0x04 +#define LQOATNPKT 0x02 +#define LQOTCRC 0x01 + +#define LQOMODE0 0x54 +#define ENLQOTARGSCBPERR 0x10 +#define ENLQOSTOPT2 0x08 +#define ENLQOATNLQ 0x04 +#define ENLQOATNPKT 0x02 +#define ENLQOTCRC 0x01 + +#define LQOMODE1 0x55 +#define ENLQOINITSCBPERR 0x10 +#define ENLQOSTOPI2 0x08 +#define ENLQOBADQAS 0x04 +#define ENLQOBUSFREE 0x02 +#define ENLQOPHACHGINPKT 0x01 + +#define CLRLQOINT1 0x55 +#define CLRLQOINITSCBPERR 0x10 +#define CLRLQOSTOPI2 0x08 +#define CLRLQOBADQAS 0x04 +#define CLRLQOBUSFREE 0x02 +#define CLRLQOPHACHGINPKT 0x01 + +#define LQOSTAT1 0x55 +#define LQOINITSCBPERR 0x10 +#define LQOSTOPI2 0x08 +#define LQOBADQAS 0x04 +#define LQOBUSFREE 0x02 +#define LQOPHACHGINPKT 0x01 + +#define LQOSTAT2 0x56 +#define LQOPKT 0xe0 +#define LQOWAITFIFO 0x10 +#define LQOPHACHGOUTPKT 0x02 +#define LQOSTOP0 0x01 + +#define OS_SPACE_CNT 0x56 + +#define SIMODE1 0x57 +#define ENSELTIMO 0x80 +#define ENATNTARG 0x40 +#define ENSCSIRST 0x20 +#define ENPHASEMIS 0x10 +#define ENBUSFREE 0x08 +#define ENSCSIPERR 0x04 +#define ENSTRB2FAST 0x02 +#define ENREQINIT 0x01 + +#define GSFIFO 0x58 + +#define DFFSXFRCTL 0x5a +#define DFFBITBUCKET 0x08 +#define CLRSHCNT 0x04 +#define CLRCHN 0x02 +#define RSTCHN 0x01 + +#define LQOSCSCTL 0x5a +#define LQOH2A_VERSION 0x80 +#define LQOBUSETDLY 0x40 +#define LQONOHOLDLACK 0x02 +#define LQONOCHKOVER 0x01 + +#define NEXTSCB 0x5a + +#define CLRSEQINTSRC 0x5b +#define CLRCTXTDONE 0x40 +#define CLRSAVEPTRS 0x20 +#define CLRCFG4DATA 0x10 +#define CLRCFG4ISTAT 0x08 +#define CLRCFG4TSTAT 0x04 +#define CLRCFG4ICMD 0x02 +#define CLRCFG4TCMD 0x01 + +#define SEQINTSRC 0x5b +#define CTXTDONE 0x40 +#define SAVEPTRS 0x20 +#define CFG4DATA 0x10 +#define CFG4ISTAT 0x08 +#define CFG4TSTAT 0x04 +#define CFG4ICMD 0x02 +#define CFG4TCMD 0x01 + +#define SEQIMODE 0x5c +#define ENCTXTDONE 0x40 +#define ENSAVEPTRS 0x20 +#define ENCFG4DATA 0x10 +#define ENCFG4ISTAT 0x08 +#define ENCFG4TSTAT 0x04 +#define ENCFG4ICMD 0x02 +#define ENCFG4TCMD 0x01 + +#define CURRSCB 0x5c + +#define CRCCONTROL 0x5d +#define CRCVALCHKEN 0x40 + +#define MDFFSTAT 0x5d +#define SHCNTNEGATIVE 0x40 +#define SHCNTMINUS1 0x20 +#define LASTSDONE 0x10 +#define SHVALID 0x08 +#define DLZERO 0x04 +#define DATAINFIFO 0x02 +#define FIFOFREE 0x01 + +#define DFFTAG 0x5e + +#define SCSITEST 0x5e +#define CNTRTEST 0x08 +#define SEL_TXPLL_DEBUG 0x04 + +#define LASTSCB 0x5e + +#define IOPDNCTL 0x5f +#define DISABLE_OE 0x80 +#define PDN_IDIST 0x04 +#define PDN_DIFFSENSE 0x01 + +#define DGRPCRCI 0x60 + +#define NEGOADDR 0x60 + +#define SHADDR 0x60 + +#define NEGPERIOD 0x61 + +#define NEGOFFSET 0x62 + +#define PACKCRCI 0x62 + +#define NEGPPROPTS 0x63 +#define PPROPT_PACE 0x08 +#define PPROPT_QAS 0x04 +#define PPROPT_DT 0x02 +#define PPROPT_IUT 0x01 + +#define NEGCONOPTS 0x64 +#define ENSNAPSHOT 0x40 +#define RTI_WRTDIS 0x20 +#define RTI_OVRDTRN 0x10 +#define ENSLOWCRC 0x08 +#define ENAUTOATNI 0x04 +#define ENAUTOATNO 0x02 +#define WIDEXFER 0x01 + +#define ANNEXCOL 0x65 + +#define ANNEXDAT 0x66 + +#define SCSCHKN 0x66 +#define BIDICHKDIS 0x80 +#define STSELSKIDDIS 0x40 +#define CURRFIFODEF 0x20 +#define WIDERESEN 0x10 +#define SDONEMSKDIS 0x08 +#define DFFACTCLR 0x04 +#define SHVALIDSTDIS 0x02 +#define LSTSGCLRDIS 0x01 + +#define IOWNID 0x67 + +#define PLL960CTL0 0x68 + +#define SHCNT 0x68 + +#define PLL960CTL1 0x69 + +#define TOWNID 0x69 + +#define PLL960CNT0 0x6a + +#define XSIG 0x6a + +#define SELOID 0x6b + +#define FAIRNESS 0x6c + +#define PLL400CTL0 0x6c +#define PLL_VCOSEL 0x80 +#define PLL_PWDN 0x40 +#define PLL_NS 0x30 +#define PLL_ENLUD 0x08 +#define PLL_ENLPF 0x04 +#define PLL_DLPF 0x02 +#define PLL_ENFBM 0x01 + +#define PLL400CTL1 0x6d +#define PLL_CNTEN 0x80 +#define PLL_CNTCLR 0x40 +#define PLL_RST 0x01 + +#define UNFAIRNESS 0x6e + +#define PLL400CNT0 0x6e + +#define HADDR 0x70 + +#define HODMAADR 0x70 + +#define PLLDELAY 0x70 +#define SPLIT_DROP_REQ 0x80 + +#define HCNT 0x78 + +#define HODMACNT 0x78 + +#define HODMAEN 0x7a + +#define SGHADDR 0x7c + +#define SCBHADDR 0x7c + +#define SGHCNT 0x84 + +#define SCBHCNT 0x84 + +#define DFF_THRSH 0x88 +#define WR_DFTHRSH 0x70 +#define RD_DFTHRSH 0x07 +#define WR_DFTHRSH_MAX 0x70 +#define WR_DFTHRSH_90 0x60 +#define WR_DFTHRSH_85 0x50 +#define WR_DFTHRSH_75 0x40 +#define WR_DFTHRSH_63 0x30 +#define WR_DFTHRSH_50 0x20 +#define WR_DFTHRSH_25 0x10 +#define RD_DFTHRSH_MAX 0x07 +#define RD_DFTHRSH_90 0x06 +#define RD_DFTHRSH_85 0x05 +#define RD_DFTHRSH_75 0x04 +#define RD_DFTHRSH_63 0x03 +#define RD_DFTHRSH_50 0x02 +#define RD_DFTHRSH_25 0x01 +#define RD_DFTHRSH_MIN 0x00 +#define WR_DFTHRSH_MIN 0x00 + +#define ROMADDR 0x8a + +#define ROMCNTRL 0x8d +#define ROMOP 0xe0 +#define ROMSPD 0x18 +#define REPEAT 0x02 +#define RDY 0x01 + +#define ROMDATA 0x8e + +#define CMCRXMSG0 0x90 + +#define OVLYRXMSG0 0x90 + +#define DCHRXMSG0 0x90 + +#define ROENABLE 0x90 +#define MSIROEN 0x20 +#define OVLYROEN 0x10 +#define CMCROEN 0x08 +#define SGROEN 0x04 +#define DCH1ROEN 0x02 +#define DCH0ROEN 0x01 + +#define OVLYRXMSG1 0x91 + +#define CMCRXMSG1 0x91 + +#define DCHRXMSG1 0x91 + +#define NSENABLE 0x91 +#define MSINSEN 0x20 +#define OVLYNSEN 0x10 +#define CMCNSEN 0x08 +#define SGNSEN 0x04 +#define DCH1NSEN 0x02 +#define DCH0NSEN 0x01 + +#define DCHRXMSG2 0x92 + +#define CMCRXMSG2 0x92 + +#define OST 0x92 + +#define OVLYRXMSG2 0x92 + +#define DCHRXMSG3 0x93 + +#define OVLYRXMSG3 0x93 + +#define CMCRXMSG3 0x93 + +#define PCIXCTL 0x93 +#define SERRPULSE 0x80 +#define UNEXPSCIEN 0x20 +#define SPLTSMADIS 0x10 +#define SPLTSTADIS 0x08 +#define SRSPDPEEN 0x04 +#define TSCSERREN 0x02 +#define CMPABCDIS 0x01 + +#define CMCSEQBCNT 0x94 + +#define OVLYSEQBCNT 0x94 + +#define DCHSEQBCNT 0x94 + +#define DCHSPLTSTAT0 0x96 + +#define OVLYSPLTSTAT0 0x96 + +#define CMCSPLTSTAT0 0x96 + +#define OVLYSPLTSTAT1 0x97 + +#define DCHSPLTSTAT1 0x97 + +#define CMCSPLTSTAT1 0x97 + +#define SGRXMSG0 0x98 +#define CDNUM 0xf8 +#define CFNUM 0x07 + +#define SLVSPLTOUTADR0 0x98 +#define LOWER_ADDR 0x7f + +#define SGRXMSG1 0x99 +#define CBNUM 0xff + +#define SLVSPLTOUTADR1 0x99 +#define REQ_DNUM 0xf8 +#define REQ_FNUM 0x07 + +#define SGRXMSG2 0x9a +#define MINDEX 0xff + +#define SLVSPLTOUTADR2 0x9a +#define REQ_BNUM 0xff + +#define SGRXMSG3 0x9b +#define MCLASS 0x0f + +#define SLVSPLTOUTADR3 0x9b +#define TAG_NUM 0x1f +#define RLXORD 0x10 + +#define SLVSPLTOUTATTR0 0x9c +#define LOWER_BCNT 0xff + +#define SGSEQBCNT 0x9c + +#define SLVSPLTOUTATTR1 0x9d +#define CMPLT_DNUM 0xf8 +#define CMPLT_FNUM 0x07 + +#define SGSPLTSTAT0 0x9e +#define STAETERM 0x80 +#define SCBCERR 0x40 +#define SCADERR 0x20 +#define SCDATBUCKET 0x10 +#define CNTNOTCMPLT 0x08 +#define RXOVRUN 0x04 +#define RXSCEMSG 0x02 +#define RXSPLTRSP 0x01 + +#define SLVSPLTOUTATTR2 0x9e +#define CMPLT_BNUM 0xff + +#define SGSPLTSTAT1 0x9f +#define RXDATABUCKET 0x01 + +#define SFUNCT 0x9f +#define TEST_GROUP 0xf0 +#define TEST_NUM 0x0f + +#define DF0PCISTAT 0xa0 + +#define REG0 0xa0 + +#define DF1PCISTAT 0xa1 + +#define SGPCISTAT 0xa2 + +#define REG1 0xa2 + +#define CMCPCISTAT 0xa3 + +#define OVLYPCISTAT 0xa4 +#define SCAAPERR 0x08 +#define RDPERR 0x04 + +#define REG_ISR 0xa4 + +#define SG_STATE 0xa6 +#define FETCH_INPROG 0x04 +#define LOADING_NEEDED 0x02 +#define SEGS_AVAIL 0x01 + +#define MSIPCISTAT 0xa6 +#define RMA 0x20 +#define RTA 0x10 +#define CLRPENDMSI 0x08 +#define DPR 0x01 + +#define DATA_COUNT_ODD 0xa7 + +#define TARGPCISTAT 0xa7 +#define DPE 0x80 +#define SSE 0x40 +#define STA 0x08 +#define TWATERR 0x02 + +#define SCBPTR 0xa8 + +#define CCSCBACNT 0xab + +#define SCBAUTOPTR 0xab +#define AUSCBPTR_EN 0x80 +#define SCBPTR_ADDR 0x38 +#define SCBPTR_OFF 0x07 + +#define CCSGADDR 0xac + +#define CCSCBADDR 0xac + +#define CCSCBADR_BK 0xac + +#define CMC_RAMBIST 0xad +#define SG_ELEMENT_SIZE 0x80 +#define SCBRAMBIST_FAIL 0x40 +#define SG_BIST_FAIL 0x20 +#define SG_BIST_EN 0x10 +#define CMC_BUFFER_BIST_FAIL 0x02 +#define CMC_BUFFER_BIST_EN 0x01 + +#define CCSCBCTL 0xad +#define CCSCBDONE 0x80 +#define ARRDONE 0x40 +#define CCARREN 0x10 +#define CCSCBEN 0x08 +#define CCSCBDIR 0x04 +#define CCSCBRESET 0x01 + +#define CCSGCTL 0xad +#define CCSGEN 0x0c +#define CCSGDONE 0x80 +#define SG_CACHE_AVAIL 0x10 +#define CCSGENACK 0x08 +#define SG_FETCH_REQ 0x02 +#define CCSGRESET 0x01 + +#define CCSGRAM 0xb0 + +#define FLEXADR 0xb0 + +#define CCSCBRAM 0xb0 + +#define FLEXCNT 0xb3 + +#define FLEXDMASTAT 0xb5 +#define FLEXDMAERR 0x02 +#define FLEXDMADONE 0x01 + +#define FLEXDATA 0xb6 + +#define BRDDAT 0xb8 + +#define BRDCTL 0xb9 +#define FLXARBACK 0x80 +#define FLXARBREQ 0x40 +#define BRDADDR 0x38 +#define BRDEN 0x04 +#define BRDRW 0x02 +#define BRDSTB 0x01 + +#define SEEADR 0xba + +#define SEEDAT 0xbc + +#define SEECTL 0xbe +#define SEEOP_EWDS 0x40 +#define SEEOP_WALL 0x40 +#define SEEOP_EWEN 0x40 +#define SEEOPCODE 0x70 +#define SEERST 0x02 +#define SEESTART 0x01 +#define SEEOP_ERASE 0x70 +#define SEEOP_READ 0x60 +#define SEEOP_WRITE 0x50 +#define SEEOP_ERAL 0x40 + +#define SEESTAT 0xbe +#define INIT_DONE 0x80 +#define LDALTID_L 0x08 +#define SEEARBACK 0x04 +#define SEEBUSY 0x02 + +#define SCBCNT 0xbf + +#define DSPFLTRCTL 0xc0 +#define FLTRDISABLE 0x20 +#define EDGESENSE 0x10 +#define DSPFCNTSEL 0x0f + +#define DFWADDR 0xc0 + +#define DSPDATACTL 0xc1 +#define BYPASSENAB 0x80 +#define DESQDIS 0x10 +#define RCVROFFSTDIS 0x04 +#define XMITOFFSTDIS 0x02 + +#define DSPREQCTL 0xc2 +#define MANREQCTL 0xc0 +#define MANREQDLY 0x3f + +#define DFRADDR 0xc2 + +#define DSPACKCTL 0xc3 +#define MANACKCTL 0xc0 +#define MANACKDLY 0x3f + +#define DFDAT 0xc4 + +#define DSPSELECT 0xc4 +#define AUTOINCEN 0x80 +#define DSPSEL 0x1f + +#define WRTBIASCTL 0xc5 +#define AUTOXBCDIS 0x80 +#define XMITMANVAL 0x3f + +#define RCVRBIOSCTL 0xc6 +#define AUTORBCDIS 0x80 +#define RCVRMANVAL 0x3f + +#define WRTBIASCALC 0xc7 + +#define DFPTRS 0xc8 + +#define RCVRBIASCALC 0xc8 + +#define DFBKPTR 0xc9 + +#define SKEWCALC 0xc9 + +#define DFDBCTL 0xcb +#define DFF_CIO_WR_RDY 0x20 +#define DFF_CIO_RD_RDY 0x10 +#define DFF_DIR_ERR 0x08 +#define DFF_RAMBIST_FAIL 0x04 +#define DFF_RAMBIST_DONE 0x02 +#define DFF_RAMBIST_EN 0x01 + +#define DFSCNT 0xcc + +#define DFBCNT 0xce + +#define OVLYADDR 0xd4 + +#define SEQCTL0 0xd6 +#define PERRORDIS 0x80 +#define PAUSEDIS 0x40 +#define FAILDIS 0x20 +#define FASTMODE 0x10 +#define BRKADRINTEN 0x08 +#define STEP 0x04 +#define SEQRESET 0x02 +#define LOADRAM 0x01 + +#define SEQCTL1 0xd7 +#define OVRLAY_DATA_CHK 0x08 +#define RAMBIST_DONE 0x04 +#define RAMBIST_FAIL 0x02 +#define RAMBIST_EN 0x01 + +#define FLAGS 0xd8 +#define ZERO 0x02 +#define CARRY 0x01 + +#define SEQINTCTL 0xd9 +#define INTVEC1DSL 0x80 +#define INT1_CONTEXT 0x20 +#define SCS_SEQ_INT1M1 0x10 +#define SCS_SEQ_INT1M0 0x08 +#define INTMASK2 0x04 +#define INTMASK1 0x02 +#define IRET 0x01 + +#define SEQRAM 0xda + +#define PRGMCNT 0xde + +#define ACCUM 0xe0 + +#define SINDEX 0xe2 + +#define DINDEX 0xe4 + +#define BRKADDR0 0xe6 + +#define BRKADDR1 0xe6 +#define BRKDIS 0x80 + +#define ALLONES 0xe8 + +#define ALLZEROS 0xea + +#define NONE 0xea + +#define SINDIR 0xec + +#define DINDIR 0xed + +#define FUNCTION1 0xf0 + +#define STACK 0xf2 + +#define INTVEC1_ADDR 0xf4 + +#define CURADDR 0xf4 + +#define LASTADDR 0xf6 + +#define INTVEC2_ADDR 0xf6 + +#define LONGJMP_ADDR 0xf8 + +#define ACCUM_SAVE 0xfa + +#define AHD_PCI_CONFIG_BASE 0x100 + +#define SRAM_BASE 0x100 + +#define WAITING_SCB_TAILS 0x100 + +#define WAITING_TID_HEAD 0x120 + +#define WAITING_TID_TAIL 0x122 + +#define NEXT_QUEUED_SCB_ADDR 0x124 + +#define COMPLETE_SCB_HEAD 0x128 + +#define COMPLETE_SCB_DMAINPROG_HEAD 0x12a + +#define COMPLETE_DMA_SCB_HEAD 0x12c + +#define COMPLETE_DMA_SCB_TAIL 0x12e + +#define COMPLETE_ON_QFREEZE_HEAD 0x130 + +#define QFREEZE_COUNT 0x132 + +#define KERNEL_QFREEZE_COUNT 0x134 + +#define SAVED_MODE 0x136 + +#define MSG_OUT 0x137 + +#define DMAPARAMS 0x138 +#define PRELOADEN 0x80 +#define WIDEODD 0x40 +#define SCSIEN 0x20 +#define SDMAENACK 0x10 +#define SDMAEN 0x10 +#define HDMAEN 0x08 +#define HDMAENACK 0x08 +#define DIRECTION 0x04 +#define FIFOFLUSH 0x02 +#define FIFORESET 0x01 + +#define SEQ_FLAGS 0x139 +#define NOT_IDENTIFIED 0x80 +#define NO_CDB_SENT 0x40 +#define TARGET_CMD_IS_TAGGED 0x40 +#define DPHASE 0x20 +#define TARG_CMD_PENDING 0x10 +#define CMDPHASE_PENDING 0x08 +#define DPHASE_PENDING 0x04 +#define SPHASE_PENDING 0x02 +#define NO_DISCONNECT 0x01 + +#define SAVED_SCSIID 0x13a + +#define SAVED_LUN 0x13b + +#define LASTPHASE 0x13c +#define PHASE_MASK 0xe0 +#define CDI 0x80 +#define IOI 0x40 +#define MSGI 0x20 +#define P_BUSFREE 0x01 +#define P_MESGIN 0xe0 +#define P_STATUS 0xc0 +#define P_MESGOUT 0xa0 +#define P_COMMAND 0x80 +#define P_DATAIN_DT 0x60 +#define P_DATAIN 0x40 +#define P_DATAOUT_DT 0x20 +#define P_DATAOUT 0x00 + +#define QOUTFIFO_ENTRY_VALID_TAG 0x13d + +#define KERNEL_TQINPOS 0x13e + +#define TQINPOS 0x13f + +#define SHARED_DATA_ADDR 0x140 + +#define QOUTFIFO_NEXT_ADDR 0x144 + +#define ARG_1 0x148 +#define RETURN_1 0x148 +#define SEND_MSG 0x80 +#define SEND_SENSE 0x40 +#define SEND_REJ 0x20 +#define MSGOUT_PHASEMIS 0x10 +#define EXIT_MSG_LOOP 0x08 +#define CONT_MSG_LOOP_WRITE 0x04 +#define CONT_MSG_LOOP_READ 0x03 +#define CONT_MSG_LOOP_TARG 0x02 + +#define ARG_2 0x149 +#define RETURN_2 0x149 + +#define LAST_MSG 0x14a + +#define SCSISEQ_TEMPLATE 0x14b +#define MANUALCTL 0x40 +#define ENSELI 0x20 +#define ENRSELI 0x10 +#define MANUALP 0x0c +#define ENAUTOATNP 0x02 +#define ALTSTIM 0x01 + +#define INITIATOR_TAG 0x14c + +#define SEQ_FLAGS2 0x14d +#define SELECTOUT_QFROZEN 0x04 +#define TARGET_MSG_PENDING 0x02 +#define PENDING_MK_MESSAGE 0x01 + +#define ALLOCFIFO_SCBPTR 0x14e + +#define INT_COALESCING_TIMER 0x150 + +#define INT_COALESCING_MAXCMDS 0x152 + +#define INT_COALESCING_MINCMDS 0x153 + +#define CMDS_PENDING 0x154 + +#define INT_COALESCING_CMDCOUNT 0x156 + +#define LOCAL_HS_MAILBOX 0x157 + +#define CMDSIZE_TABLE 0x158 + +#define MK_MESSAGE_SCB 0x160 + +#define MK_MESSAGE_SCSIID 0x162 + +#define SCB_RESIDUAL_DATACNT 0x180 +#define SCB_CDB_STORE 0x180 +#define SCB_HOST_CDB_PTR 0x180 + +#define SCB_BASE 0x180 + +#define SCB_RESIDUAL_SGPTR 0x184 +#define SG_ADDR_MASK 0xf8 +#define SG_OVERRUN_RESID 0x02 + +#define SCB_SCSI_STATUS 0x188 +#define SCB_HOST_CDB_LEN 0x188 + +#define SCB_TARGET_PHASES 0x189 + +#define SCB_TARGET_DATA_DIR 0x18a + +#define SCB_TARGET_ITAG 0x18b + +#define SCB_SENSE_BUSADDR 0x18c +#define SCB_NEXT_COMPLETE 0x18c + +#define SCB_TAG 0x190 +#define SCB_FIFO_USE_COUNT 0x190 + +#define SCB_CONTROL 0x192 +#define TARGET_SCB 0x80 +#define DISCENB 0x40 +#define TAG_ENB 0x20 +#define MK_MESSAGE 0x10 +#define STATUS_RCVD 0x08 +#define DISCONNECTED 0x04 +#define SCB_TAG_TYPE 0x03 + +#define SCB_SCSIID 0x193 +#define TID 0xf0 +#define OID 0x0f + +#define SCB_LUN 0x194 +#define LID 0xff + +#define SCB_TASK_ATTRIBUTE 0x195 +#define SCB_XFERLEN_ODD 0x01 + +#define SCB_CDB_LEN 0x196 +#define SCB_CDB_LEN_PTR 0x80 + +#define SCB_TASK_MANAGEMENT 0x197 + +#define SCB_DATAPTR 0x198 + +#define SCB_DATACNT 0x1a0 +#define SG_LAST_SEG 0x80 +#define SG_HIGH_ADDR_BITS 0x7f + +#define SCB_SGPTR 0x1a4 +#define SG_STATUS_VALID 0x04 +#define SG_FULL_RESID 0x02 +#define SG_LIST_NULL 0x01 + +#define SCB_BUSADDR 0x1a8 + +#define SCB_NEXT 0x1ac +#define SCB_NEXT_SCB_BUSADDR 0x1ac + +#define SCB_NEXT2 0x1ae + +#define SCB_SPARE 0x1b0 +#define SCB_PKT_LUN 0x1b0 + +#define SCB_DISCONNECTED_LISTS 0x1b8 + + +#define STIMESEL_SHIFT 0x03 +#define STIMESEL_MIN 0x18 +#define INVALID_ADDR 0x80 +#define CMD_GROUP_CODE_SHIFT 0x05 +#define AHD_PRECOMP_MASK 0x07 +#define TARGET_DATA_IN 0x01 +#define SEEOP_EWEN_ADDR 0xc0 +#define NUMDSPS 0x14 +#define DST_MODE_SHIFT 0x04 +#define CCSCBADDR_MAX 0x80 +#define AHD_ANNEXCOL_PER_DEV0 0x04 +#define TARGET_CMD_CMPLT 0xfe +#define SEEOP_WRAL_ADDR 0x40 +#define BUS_8_BIT 0x00 +#define AHD_TIMER_MAX_US 0x18ffe7 +#define AHD_TIMER_MAX_TICKS 0xffff +#define AHD_SENSE_BUFSIZE 0x100 +#define AHD_PRECOMP_SHIFT 0x00 +#define AHD_PRECOMP_CUTBACK_37 0x07 +#define AHD_ANNEXCOL_PRECOMP_SLEW 0x04 +#define AHD_AMPLITUDE_DEF 0x07 +#define WRTBIASCTL_HP_DEFAULT 0x00 +#define TID_SHIFT 0x04 +#define STATUS_QUEUE_FULL 0x28 +#define STATUS_BUSY 0x08 +#define SEEOP_EWDS_ADDR 0x00 +#define SCB_TRANSFER_SIZE_FULL_LUN 0x38 +#define MK_MESSAGE_BIT_OFFSET 0x04 +#define MAX_OFFSET_PACED 0xfe +#define MAX_OFFSET_NON_PACED 0x7f +#define LUNLEN_SINGLE_LEVEL_LUN 0x0f +#define CCSGADDR_MAX 0x80 +#define B_CURRFIFO_0 0x02 +#define BUS_32_BIT 0x02 +#define AHD_TIMER_US_PER_TICK 0x19 +#define AHD_SLEWRATE_SHIFT 0x03 +#define AHD_SLEWRATE_MASK 0x78 +#define AHD_SLEWRATE_DEF_REVA 0x08 +#define AHD_PRECOMP_CUTBACK_29 0x06 +#define AHD_NUM_PER_DEV_ANNEXCOLS 0x04 +#define AHD_ANNEXCOL_AMPLITUDE 0x06 +#define AHD_AMPLITUDE_SHIFT 0x00 +#define AHD_AMPLITUDE_MASK 0x07 +#define STIMESEL_BUG_ADJ 0x08 +#define STATUS_PKT_SENSE 0xff +#define SRC_MODE_SHIFT 0x00 +#define SEEOP_ERAL_ADDR 0x80 +#define NVRAM_SCB_OFFSET 0x2c +#define MAX_OFFSET_PACED_BUG 0x7f +#define CCSGRAM_MAXSEGS 0x10 +#define AHD_SLEWRATE_DEF_REVB 0x08 +#define AHD_PRECOMP_CUTBACK_17 0x04 +#define SCB_TRANSFER_SIZE_1BYTE_LUN 0x30 +#define PKT_OVERRUN_BUFSIZE 0x200 +#define MAX_OFFSET 0xfe +#define HOST_MSG 0xff +#define BUS_16_BIT 0x01 + + +/* Downloaded Constant Definitions */ +#define SG_SIZEOF 0x04 +#define SG_PREFETCH_ALIGN_MASK 0x02 +#define SG_PREFETCH_CNT_LIMIT 0x01 +#define CACHELINE_MASK 0x07 +#define SCB_TRANSFER_SIZE 0x06 +#define PKT_OVERRUN_BUFOFFSET 0x05 +#define SG_PREFETCH_ADDR_MASK 0x03 +#define SG_PREFETCH_CNT 0x00 +#define DOWNLOAD_CONST_COUNT 0x08 + + +/* Exported Labels */ +#define LABEL_timer_isr 0x28b +#define LABEL_seq_isr 0x28f diff --git a/drivers/scsi/aic7xxx/aic79xx_reg_print.c_shipped b/drivers/scsi/aic7xxx/aic79xx_reg_print.c_shipped new file mode 100644 index 000000000..2e0c58905 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx_reg_print.c_shipped @@ -0,0 +1,745 @@ +/* + * DO NOT EDIT - This file is automatically generated + * from the following source files: + * + * $Id: //depot/aic7xxx/aic7xxx/aic79xx.seq#120 $ + * $Id: //depot/aic7xxx/aic7xxx/aic79xx.reg#77 $ + */ + +#include "aic79xx_osm.h" + +static const ahd_reg_parse_entry_t INTSTAT_parse_table[] = { + { "SPLTINT", 0x01, 0x01 }, + { "CMDCMPLT", 0x02, 0x02 }, + { "SEQINT", 0x04, 0x04 }, + { "SCSIINT", 0x08, 0x08 }, + { "PCIINT", 0x10, 0x10 }, + { "SWTMINT", 0x20, 0x20 }, + { "BRKADRINT", 0x40, 0x40 }, + { "HWERRINT", 0x80, 0x80 }, + { "INT_PEND", 0xff, 0xff } +}; + +int +ahd_intstat_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(INTSTAT_parse_table, 9, "INTSTAT", + 0x01, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t HS_MAILBOX_parse_table[] = { + { "ENINT_COALESCE", 0x40, 0x40 }, + { "HOST_TQINPOS", 0x80, 0x80 } +}; + +int +ahd_hs_mailbox_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(HS_MAILBOX_parse_table, 2, "HS_MAILBOX", + 0x0b, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SEQINTSTAT_parse_table[] = { + { "SEQ_SPLTINT", 0x01, 0x01 }, + { "SEQ_PCIINT", 0x02, 0x02 }, + { "SEQ_SCSIINT", 0x04, 0x04 }, + { "SEQ_SEQINT", 0x08, 0x08 }, + { "SEQ_SWTMRTO", 0x10, 0x10 } +}; + +int +ahd_seqintstat_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SEQINTSTAT_parse_table, 5, "SEQINTSTAT", + 0x0c, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t INTCTL_parse_table[] = { + { "SPLTINTEN", 0x01, 0x01 }, + { "SEQINTEN", 0x02, 0x02 }, + { "SCSIINTEN", 0x04, 0x04 }, + { "PCIINTEN", 0x08, 0x08 }, + { "AUTOCLRCMDINT", 0x10, 0x10 }, + { "SWTIMER_START", 0x20, 0x20 }, + { "SWTMINTEN", 0x40, 0x40 }, + { "SWTMINTMASK", 0x80, 0x80 } +}; + +int +ahd_intctl_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(INTCTL_parse_table, 8, "INTCTL", + 0x18, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t DFCNTRL_parse_table[] = { + { "DIRECTIONEN", 0x01, 0x01 }, + { "FIFOFLUSH", 0x02, 0x02 }, + { "FIFOFLUSHACK", 0x02, 0x02 }, + { "DIRECTION", 0x04, 0x04 }, + { "DIRECTIONACK", 0x04, 0x04 }, + { "HDMAEN", 0x08, 0x08 }, + { "HDMAENACK", 0x08, 0x08 }, + { "SCSIEN", 0x20, 0x20 }, + { "SCSIENACK", 0x20, 0x20 }, + { "SCSIENWRDIS", 0x40, 0x40 }, + { "PRELOADEN", 0x80, 0x80 } +}; + +int +ahd_dfcntrl_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(DFCNTRL_parse_table, 11, "DFCNTRL", + 0x19, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t DFSTATUS_parse_table[] = { + { "FIFOEMP", 0x01, 0x01 }, + { "FIFOFULL", 0x02, 0x02 }, + { "DFTHRESH", 0x04, 0x04 }, + { "HDONE", 0x08, 0x08 }, + { "MREQPEND", 0x10, 0x10 }, + { "PKT_PRELOAD_AVAIL", 0x40, 0x40 }, + { "PRELOAD_AVAIL", 0x80, 0x80 } +}; + +int +ahd_dfstatus_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(DFSTATUS_parse_table, 7, "DFSTATUS", + 0x1a, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SG_CACHE_SHADOW_parse_table[] = { + { "LAST_SEG_DONE", 0x01, 0x01 }, + { "LAST_SEG", 0x02, 0x02 }, + { "ODD_SEG", 0x04, 0x04 }, + { "SG_ADDR_MASK", 0xf8, 0xf8 } +}; + +int +ahd_sg_cache_shadow_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SG_CACHE_SHADOW_parse_table, 4, "SG_CACHE_SHADOW", + 0x1b, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SCSISEQ0_parse_table[] = { + { "SCSIRSTO", 0x01, 0x01 }, + { "FORCEBUSFREE", 0x10, 0x10 }, + { "ENARBO", 0x20, 0x20 }, + { "ENSELO", 0x40, 0x40 }, + { "TEMODEO", 0x80, 0x80 } +}; + +int +ahd_scsiseq0_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SCSISEQ0_parse_table, 5, "SCSISEQ0", + 0x3a, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SCSISEQ1_parse_table[] = { + { "ALTSTIM", 0x01, 0x01 }, + { "ENAUTOATNP", 0x02, 0x02 }, + { "MANUALP", 0x0c, 0x0c }, + { "ENRSELI", 0x10, 0x10 }, + { "ENSELI", 0x20, 0x20 }, + { "MANUALCTL", 0x40, 0x40 } +}; + +int +ahd_scsiseq1_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SCSISEQ1_parse_table, 6, "SCSISEQ1", + 0x3b, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t DFFSTAT_parse_table[] = { + { "CURRFIFO_0", 0x00, 0x03 }, + { "CURRFIFO_1", 0x01, 0x03 }, + { "CURRFIFO_NONE", 0x03, 0x03 }, + { "FIFO0FREE", 0x10, 0x10 }, + { "FIFO1FREE", 0x20, 0x20 }, + { "CURRFIFO", 0x03, 0x03 } +}; + +int +ahd_dffstat_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(DFFSTAT_parse_table, 6, "DFFSTAT", + 0x3f, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SCSISIGI_parse_table[] = { + { "P_DATAOUT", 0x00, 0xe0 }, + { "P_DATAOUT_DT", 0x20, 0xe0 }, + { "P_DATAIN", 0x40, 0xe0 }, + { "P_DATAIN_DT", 0x60, 0xe0 }, + { "P_COMMAND", 0x80, 0xe0 }, + { "P_MESGOUT", 0xa0, 0xe0 }, + { "P_STATUS", 0xc0, 0xe0 }, + { "P_MESGIN", 0xe0, 0xe0 }, + { "ACKI", 0x01, 0x01 }, + { "REQI", 0x02, 0x02 }, + { "BSYI", 0x04, 0x04 }, + { "SELI", 0x08, 0x08 }, + { "ATNI", 0x10, 0x10 }, + { "MSGI", 0x20, 0x20 }, + { "IOI", 0x40, 0x40 }, + { "CDI", 0x80, 0x80 }, + { "PHASE_MASK", 0xe0, 0xe0 } +}; + +int +ahd_scsisigi_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SCSISIGI_parse_table, 17, "SCSISIGI", + 0x41, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SCSIPHASE_parse_table[] = { + { "DATA_OUT_PHASE", 0x01, 0x03 }, + { "DATA_IN_PHASE", 0x02, 0x03 }, + { "DATA_PHASE_MASK", 0x03, 0x03 }, + { "MSG_OUT_PHASE", 0x04, 0x04 }, + { "MSG_IN_PHASE", 0x08, 0x08 }, + { "COMMAND_PHASE", 0x10, 0x10 }, + { "STATUS_PHASE", 0x20, 0x20 } +}; + +int +ahd_scsiphase_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SCSIPHASE_parse_table, 7, "SCSIPHASE", + 0x42, regvalue, cur_col, wrap)); +} + +int +ahd_scsibus_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(NULL, 0, "SCSIBUS", + 0x46, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SELID_parse_table[] = { + { "ONEBIT", 0x08, 0x08 }, + { "SELID_MASK", 0xf0, 0xf0 } +}; + +int +ahd_selid_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SELID_parse_table, 2, "SELID", + 0x49, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SIMODE0_parse_table[] = { + { "ENARBDO", 0x01, 0x01 }, + { "ENSPIORDY", 0x02, 0x02 }, + { "ENOVERRUN", 0x04, 0x04 }, + { "ENIOERR", 0x08, 0x08 }, + { "ENSELINGO", 0x10, 0x10 }, + { "ENSELDI", 0x20, 0x20 }, + { "ENSELDO", 0x40, 0x40 } +}; + +int +ahd_simode0_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SIMODE0_parse_table, 7, "SIMODE0", + 0x4b, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SSTAT0_parse_table[] = { + { "ARBDO", 0x01, 0x01 }, + { "SPIORDY", 0x02, 0x02 }, + { "OVERRUN", 0x04, 0x04 }, + { "IOERR", 0x08, 0x08 }, + { "SELINGO", 0x10, 0x10 }, + { "SELDI", 0x20, 0x20 }, + { "SELDO", 0x40, 0x40 }, + { "TARGET", 0x80, 0x80 } +}; + +int +ahd_sstat0_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SSTAT0_parse_table, 8, "SSTAT0", + 0x4b, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SSTAT1_parse_table[] = { + { "REQINIT", 0x01, 0x01 }, + { "STRB2FAST", 0x02, 0x02 }, + { "SCSIPERR", 0x04, 0x04 }, + { "BUSFREE", 0x08, 0x08 }, + { "PHASEMIS", 0x10, 0x10 }, + { "SCSIRSTI", 0x20, 0x20 }, + { "ATNTARG", 0x40, 0x40 }, + { "SELTO", 0x80, 0x80 } +}; + +int +ahd_sstat1_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SSTAT1_parse_table, 8, "SSTAT1", + 0x4c, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SSTAT2_parse_table[] = { + { "BUSFREE_LQO", 0x40, 0xc0 }, + { "BUSFREE_DFF0", 0x80, 0xc0 }, + { "BUSFREE_DFF1", 0xc0, 0xc0 }, + { "DMADONE", 0x01, 0x01 }, + { "SDONE", 0x02, 0x02 }, + { "WIDE_RES", 0x04, 0x04 }, + { "BSYX", 0x08, 0x08 }, + { "EXP_ACTIVE", 0x10, 0x10 }, + { "NONPACKREQ", 0x20, 0x20 }, + { "BUSFREETIME", 0xc0, 0xc0 } +}; + +int +ahd_sstat2_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SSTAT2_parse_table, 10, "SSTAT2", + 0x4d, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t PERRDIAG_parse_table[] = { + { "DTERR", 0x01, 0x01 }, + { "DGFORMERR", 0x02, 0x02 }, + { "CRCERR", 0x04, 0x04 }, + { "AIPERR", 0x08, 0x08 }, + { "PARITYERR", 0x10, 0x10 }, + { "PREVPHASE", 0x20, 0x20 }, + { "HIPERR", 0x40, 0x40 }, + { "HIZERO", 0x80, 0x80 } +}; + +int +ahd_perrdiag_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(PERRDIAG_parse_table, 8, "PERRDIAG", + 0x4e, regvalue, cur_col, wrap)); +} + +int +ahd_soffcnt_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(NULL, 0, "SOFFCNT", + 0x4f, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t LQISTAT0_parse_table[] = { + { "LQIATNCMD", 0x01, 0x01 }, + { "LQIATNLQ", 0x02, 0x02 }, + { "LQIBADLQT", 0x04, 0x04 }, + { "LQICRCT2", 0x08, 0x08 }, + { "LQICRCT1", 0x10, 0x10 }, + { "LQIATNQAS", 0x20, 0x20 } +}; + +int +ahd_lqistat0_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(LQISTAT0_parse_table, 6, "LQISTAT0", + 0x50, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t LQISTAT1_parse_table[] = { + { "LQIOVERI_NLQ", 0x01, 0x01 }, + { "LQIOVERI_LQ", 0x02, 0x02 }, + { "LQIBADLQI", 0x04, 0x04 }, + { "LQICRCI_NLQ", 0x08, 0x08 }, + { "LQICRCI_LQ", 0x10, 0x10 }, + { "LQIABORT", 0x20, 0x20 }, + { "LQIPHASE_NLQ", 0x40, 0x40 }, + { "LQIPHASE_LQ", 0x80, 0x80 } +}; + +int +ahd_lqistat1_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(LQISTAT1_parse_table, 8, "LQISTAT1", + 0x51, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t LQISTAT2_parse_table[] = { + { "LQIGSAVAIL", 0x01, 0x01 }, + { "LQISTOPCMD", 0x02, 0x02 }, + { "LQISTOPLQ", 0x04, 0x04 }, + { "LQISTOPPKT", 0x08, 0x08 }, + { "LQIWAITFIFO", 0x10, 0x10 }, + { "LQIWORKONLQ", 0x20, 0x20 }, + { "LQIPHASE_OUTPKT", 0x40, 0x40 }, + { "PACKETIZED", 0x80, 0x80 } +}; + +int +ahd_lqistat2_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(LQISTAT2_parse_table, 8, "LQISTAT2", + 0x52, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SSTAT3_parse_table[] = { + { "OSRAMPERR", 0x01, 0x01 }, + { "NTRAMPERR", 0x02, 0x02 } +}; + +int +ahd_sstat3_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SSTAT3_parse_table, 2, "SSTAT3", + 0x53, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t LQOSTAT0_parse_table[] = { + { "LQOTCRC", 0x01, 0x01 }, + { "LQOATNPKT", 0x02, 0x02 }, + { "LQOATNLQ", 0x04, 0x04 }, + { "LQOSTOPT2", 0x08, 0x08 }, + { "LQOTARGSCBPERR", 0x10, 0x10 } +}; + +int +ahd_lqostat0_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(LQOSTAT0_parse_table, 5, "LQOSTAT0", + 0x54, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t LQOSTAT1_parse_table[] = { + { "LQOPHACHGINPKT", 0x01, 0x01 }, + { "LQOBUSFREE", 0x02, 0x02 }, + { "LQOBADQAS", 0x04, 0x04 }, + { "LQOSTOPI2", 0x08, 0x08 }, + { "LQOINITSCBPERR", 0x10, 0x10 } +}; + +int +ahd_lqostat1_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(LQOSTAT1_parse_table, 5, "LQOSTAT1", + 0x55, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t LQOSTAT2_parse_table[] = { + { "LQOSTOP0", 0x01, 0x01 }, + { "LQOPHACHGOUTPKT", 0x02, 0x02 }, + { "LQOWAITFIFO", 0x10, 0x10 }, + { "LQOPKT", 0xe0, 0xe0 } +}; + +int +ahd_lqostat2_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(LQOSTAT2_parse_table, 4, "LQOSTAT2", + 0x56, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SIMODE1_parse_table[] = { + { "ENREQINIT", 0x01, 0x01 }, + { "ENSTRB2FAST", 0x02, 0x02 }, + { "ENSCSIPERR", 0x04, 0x04 }, + { "ENBUSFREE", 0x08, 0x08 }, + { "ENPHASEMIS", 0x10, 0x10 }, + { "ENSCSIRST", 0x20, 0x20 }, + { "ENATNTARG", 0x40, 0x40 }, + { "ENSELTIMO", 0x80, 0x80 } +}; + +int +ahd_simode1_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SIMODE1_parse_table, 8, "SIMODE1", + 0x57, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t DFFSXFRCTL_parse_table[] = { + { "RSTCHN", 0x01, 0x01 }, + { "CLRCHN", 0x02, 0x02 }, + { "CLRSHCNT", 0x04, 0x04 }, + { "DFFBITBUCKET", 0x08, 0x08 } +}; + +int +ahd_dffsxfrctl_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(DFFSXFRCTL_parse_table, 4, "DFFSXFRCTL", + 0x5a, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SEQINTSRC_parse_table[] = { + { "CFG4TCMD", 0x01, 0x01 }, + { "CFG4ICMD", 0x02, 0x02 }, + { "CFG4TSTAT", 0x04, 0x04 }, + { "CFG4ISTAT", 0x08, 0x08 }, + { "CFG4DATA", 0x10, 0x10 }, + { "SAVEPTRS", 0x20, 0x20 }, + { "CTXTDONE", 0x40, 0x40 } +}; + +int +ahd_seqintsrc_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SEQINTSRC_parse_table, 7, "SEQINTSRC", + 0x5b, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SEQIMODE_parse_table[] = { + { "ENCFG4TCMD", 0x01, 0x01 }, + { "ENCFG4ICMD", 0x02, 0x02 }, + { "ENCFG4TSTAT", 0x04, 0x04 }, + { "ENCFG4ISTAT", 0x08, 0x08 }, + { "ENCFG4DATA", 0x10, 0x10 }, + { "ENSAVEPTRS", 0x20, 0x20 }, + { "ENCTXTDONE", 0x40, 0x40 } +}; + +int +ahd_seqimode_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SEQIMODE_parse_table, 7, "SEQIMODE", + 0x5c, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t MDFFSTAT_parse_table[] = { + { "FIFOFREE", 0x01, 0x01 }, + { "DATAINFIFO", 0x02, 0x02 }, + { "DLZERO", 0x04, 0x04 }, + { "SHVALID", 0x08, 0x08 }, + { "LASTSDONE", 0x10, 0x10 }, + { "SHCNTMINUS1", 0x20, 0x20 }, + { "SHCNTNEGATIVE", 0x40, 0x40 } +}; + +int +ahd_mdffstat_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(MDFFSTAT_parse_table, 7, "MDFFSTAT", + 0x5d, regvalue, cur_col, wrap)); +} + +int +ahd_seloid_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(NULL, 0, "SELOID", + 0x6b, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SG_STATE_parse_table[] = { + { "SEGS_AVAIL", 0x01, 0x01 }, + { "LOADING_NEEDED", 0x02, 0x02 }, + { "FETCH_INPROG", 0x04, 0x04 } +}; + +int +ahd_sg_state_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SG_STATE_parse_table, 3, "SG_STATE", + 0xa6, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t CCSCBCTL_parse_table[] = { + { "CCSCBRESET", 0x01, 0x01 }, + { "CCSCBDIR", 0x04, 0x04 }, + { "CCSCBEN", 0x08, 0x08 }, + { "CCARREN", 0x10, 0x10 }, + { "ARRDONE", 0x40, 0x40 }, + { "CCSCBDONE", 0x80, 0x80 } +}; + +int +ahd_ccscbctl_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(CCSCBCTL_parse_table, 6, "CCSCBCTL", + 0xad, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t CCSGCTL_parse_table[] = { + { "CCSGRESET", 0x01, 0x01 }, + { "SG_FETCH_REQ", 0x02, 0x02 }, + { "CCSGENACK", 0x08, 0x08 }, + { "SG_CACHE_AVAIL", 0x10, 0x10 }, + { "CCSGDONE", 0x80, 0x80 }, + { "CCSGEN", 0x0c, 0x0c } +}; + +int +ahd_ccsgctl_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(CCSGCTL_parse_table, 6, "CCSGCTL", + 0xad, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SEQCTL0_parse_table[] = { + { "LOADRAM", 0x01, 0x01 }, + { "SEQRESET", 0x02, 0x02 }, + { "STEP", 0x04, 0x04 }, + { "BRKADRINTEN", 0x08, 0x08 }, + { "FASTMODE", 0x10, 0x10 }, + { "FAILDIS", 0x20, 0x20 }, + { "PAUSEDIS", 0x40, 0x40 }, + { "PERRORDIS", 0x80, 0x80 } +}; + +int +ahd_seqctl0_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SEQCTL0_parse_table, 8, "SEQCTL0", + 0xd6, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SEQINTCTL_parse_table[] = { + { "IRET", 0x01, 0x01 }, + { "INTMASK1", 0x02, 0x02 }, + { "INTMASK2", 0x04, 0x04 }, + { "SCS_SEQ_INT1M0", 0x08, 0x08 }, + { "SCS_SEQ_INT1M1", 0x10, 0x10 }, + { "INT1_CONTEXT", 0x20, 0x20 }, + { "INTVEC1DSL", 0x80, 0x80 } +}; + +int +ahd_seqintctl_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SEQINTCTL_parse_table, 7, "SEQINTCTL", + 0xd9, regvalue, cur_col, wrap)); +} + +int +ahd_sram_base_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(NULL, 0, "SRAM_BASE", + 0x100, regvalue, cur_col, wrap)); +} + +int +ahd_qfreeze_count_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(NULL, 0, "QFREEZE_COUNT", + 0x132, regvalue, cur_col, wrap)); +} + +int +ahd_kernel_qfreeze_count_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(NULL, 0, "KERNEL_QFREEZE_COUNT", + 0x134, regvalue, cur_col, wrap)); +} + +int +ahd_saved_mode_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(NULL, 0, "SAVED_MODE", + 0x136, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SEQ_FLAGS_parse_table[] = { + { "NO_DISCONNECT", 0x01, 0x01 }, + { "SPHASE_PENDING", 0x02, 0x02 }, + { "DPHASE_PENDING", 0x04, 0x04 }, + { "CMDPHASE_PENDING", 0x08, 0x08 }, + { "TARG_CMD_PENDING", 0x10, 0x10 }, + { "DPHASE", 0x20, 0x20 }, + { "NO_CDB_SENT", 0x40, 0x40 }, + { "TARGET_CMD_IS_TAGGED",0x40, 0x40 }, + { "NOT_IDENTIFIED", 0x80, 0x80 } +}; + +int +ahd_seq_flags_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SEQ_FLAGS_parse_table, 9, "SEQ_FLAGS", + 0x139, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t LASTPHASE_parse_table[] = { + { "P_DATAOUT", 0x00, 0xe0 }, + { "P_DATAOUT_DT", 0x20, 0xe0 }, + { "P_DATAIN", 0x40, 0xe0 }, + { "P_DATAIN_DT", 0x60, 0xe0 }, + { "P_COMMAND", 0x80, 0xe0 }, + { "P_MESGOUT", 0xa0, 0xe0 }, + { "P_STATUS", 0xc0, 0xe0 }, + { "P_MESGIN", 0xe0, 0xe0 }, + { "P_BUSFREE", 0x01, 0x01 }, + { "MSGI", 0x20, 0x20 }, + { "IOI", 0x40, 0x40 }, + { "CDI", 0x80, 0x80 }, + { "PHASE_MASK", 0xe0, 0xe0 } +}; + +int +ahd_lastphase_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(LASTPHASE_parse_table, 13, "LASTPHASE", + 0x13c, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SEQ_FLAGS2_parse_table[] = { + { "PENDING_MK_MESSAGE", 0x01, 0x01 }, + { "TARGET_MSG_PENDING", 0x02, 0x02 }, + { "SELECTOUT_QFROZEN", 0x04, 0x04 } +}; + +int +ahd_seq_flags2_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SEQ_FLAGS2_parse_table, 3, "SEQ_FLAGS2", + 0x14d, regvalue, cur_col, wrap)); +} + +int +ahd_mk_message_scb_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(NULL, 0, "MK_MESSAGE_SCB", + 0x160, regvalue, cur_col, wrap)); +} + +int +ahd_mk_message_scsiid_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(NULL, 0, "MK_MESSAGE_SCSIID", + 0x162, regvalue, cur_col, wrap)); +} + +int +ahd_scb_base_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(NULL, 0, "SCB_BASE", + 0x180, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SCB_CONTROL_parse_table[] = { + { "SCB_TAG_TYPE", 0x03, 0x03 }, + { "DISCONNECTED", 0x04, 0x04 }, + { "STATUS_RCVD", 0x08, 0x08 }, + { "MK_MESSAGE", 0x10, 0x10 }, + { "TAG_ENB", 0x20, 0x20 }, + { "DISCENB", 0x40, 0x40 }, + { "TARGET_SCB", 0x80, 0x80 } +}; + +int +ahd_scb_control_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SCB_CONTROL_parse_table, 7, "SCB_CONTROL", + 0x192, regvalue, cur_col, wrap)); +} + +static const ahd_reg_parse_entry_t SCB_SCSIID_parse_table[] = { + { "OID", 0x0f, 0x0f }, + { "TID", 0xf0, 0xf0 } +}; + +int +ahd_scb_scsiid_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahd_print_register(SCB_SCSIID_parse_table, 2, "SCB_SCSIID", + 0x193, regvalue, cur_col, wrap)); +} + diff --git a/drivers/scsi/aic7xxx/aic79xx_seq.h_shipped b/drivers/scsi/aic7xxx/aic79xx_seq.h_shipped new file mode 100644 index 000000000..fd64a950e --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx_seq.h_shipped @@ -0,0 +1,1189 @@ +/* + * DO NOT EDIT - This file is automatically generated + * from the following source files: + * + * $Id: //depot/aic7xxx/aic7xxx/aic79xx.seq#120 $ + * $Id: //depot/aic7xxx/aic7xxx/aic79xx.reg#77 $ + */ +static const uint8_t seqprog[] = { + 0xff, 0x02, 0x06, 0x78, + 0x00, 0xea, 0x6e, 0x59, + 0x01, 0xea, 0x04, 0x30, + 0xff, 0x04, 0x0c, 0x78, + 0x19, 0xea, 0x6e, 0x59, + 0x19, 0xea, 0x04, 0x00, + 0x33, 0xea, 0x68, 0x59, + 0x33, 0xea, 0x00, 0x00, + 0x60, 0x3a, 0x3a, 0x68, + 0x04, 0x4d, 0x35, 0x78, + 0x01, 0x34, 0xc1, 0x31, + 0x00, 0x32, 0x21, 0x60, + 0x01, 0x35, 0xc1, 0x31, + 0x00, 0x33, 0x21, 0x60, + 0xfb, 0x4d, 0x9b, 0x0a, + 0x00, 0xe2, 0x34, 0x40, + 0x50, 0x4b, 0x3a, 0x68, + 0xff, 0x31, 0x3b, 0x70, + 0x02, 0x30, 0x51, 0x31, + 0xff, 0x8d, 0x2d, 0x70, + 0x02, 0x8c, 0x51, 0x31, + 0xff, 0x8d, 0x29, 0x60, + 0x02, 0x28, 0x19, 0x33, + 0x02, 0x30, 0x51, 0x32, + 0xff, 0xea, 0x62, 0x02, + 0x00, 0xe2, 0x3a, 0x40, + 0xff, 0x21, 0x3b, 0x70, + 0x40, 0x4b, 0xb4, 0x69, + 0x00, 0xe2, 0x72, 0x59, + 0x40, 0x4b, 0xb4, 0x69, + 0x20, 0x4b, 0xa0, 0x69, + 0xfc, 0x42, 0x44, 0x78, + 0x10, 0x40, 0x44, 0x78, + 0x00, 0xe2, 0x10, 0x5e, + 0x20, 0x4d, 0x48, 0x78, + 0x00, 0xe2, 0x10, 0x5e, + 0x30, 0x3f, 0xc0, 0x09, + 0x30, 0xe0, 0x50, 0x60, + 0x7f, 0x4a, 0x94, 0x08, + 0x00, 0xe2, 0x52, 0x40, + 0xc0, 0x4a, 0x94, 0x00, + 0x00, 0xe2, 0x5e, 0x58, + 0x00, 0xe2, 0x76, 0x58, + 0x00, 0xe2, 0x86, 0x58, + 0x00, 0xe2, 0x06, 0x40, + 0x33, 0xea, 0x68, 0x59, + 0x33, 0xea, 0x00, 0x00, + 0x01, 0x52, 0x84, 0x78, + 0x02, 0x58, 0x50, 0x31, + 0xff, 0xea, 0x10, 0x0b, + 0xff, 0x97, 0x6f, 0x78, + 0x50, 0x4b, 0x6a, 0x68, + 0xbf, 0x3a, 0x74, 0x08, + 0x14, 0xea, 0x6e, 0x59, + 0x14, 0xea, 0x04, 0x00, + 0x08, 0x92, 0x25, 0x03, + 0xff, 0x90, 0x5f, 0x68, + 0x00, 0xe2, 0x8a, 0x5b, + 0x00, 0xe2, 0x5e, 0x40, + 0x00, 0xea, 0x68, 0x59, + 0x01, 0xea, 0x00, 0x30, + 0x80, 0xf9, 0x7e, 0x68, + 0x00, 0xe2, 0x66, 0x59, + 0x11, 0xea, 0x68, 0x59, + 0x11, 0xea, 0x00, 0x00, + 0x80, 0xf9, 0x66, 0x79, + 0xff, 0xea, 0xd4, 0x0d, + 0x22, 0xea, 0x68, 0x59, + 0x22, 0xea, 0x00, 0x00, + 0x10, 0x16, 0x90, 0x78, + 0x10, 0x16, 0x2c, 0x00, + 0x01, 0x0b, 0xae, 0x32, + 0x18, 0xad, 0x1c, 0x79, + 0x04, 0xad, 0xdc, 0x68, + 0x80, 0xad, 0x84, 0x78, + 0x10, 0xad, 0xaa, 0x78, + 0xe7, 0xad, 0x5a, 0x09, + 0x02, 0x8c, 0x59, 0x32, + 0xff, 0x8d, 0xa1, 0x60, + 0xff, 0xea, 0x5e, 0x02, + 0xff, 0x88, 0xa7, 0x78, + 0x02, 0x30, 0x19, 0x33, + 0x02, 0xa8, 0x60, 0x36, + 0x02, 0x28, 0x19, 0x33, + 0x02, 0xa8, 0x50, 0x36, + 0xe7, 0xad, 0x5a, 0x09, + 0x00, 0xe2, 0xb8, 0x58, + 0xff, 0xea, 0x56, 0x02, + 0x04, 0x7c, 0x88, 0x32, + 0x20, 0x16, 0x84, 0x78, + 0x04, 0x40, 0x89, 0x32, + 0x80, 0x3d, 0x7b, 0x16, + 0xff, 0x2d, 0xc7, 0x60, + 0xff, 0x29, 0xc7, 0x60, + 0x40, 0x57, 0xd7, 0x78, + 0xff, 0x55, 0xc7, 0x68, + 0xff, 0x53, 0xc1, 0x19, + 0x00, 0x54, 0xd5, 0x19, + 0x00, 0xe2, 0xd6, 0x50, + 0x01, 0x52, 0xc1, 0x31, + 0x00, 0x56, 0xd5, 0x19, + 0x00, 0xe2, 0xd6, 0x48, + 0x80, 0x18, 0x84, 0x78, + 0x02, 0x50, 0x1d, 0x30, + 0x10, 0xea, 0x18, 0x00, + 0x60, 0x18, 0x30, 0x00, + 0x7f, 0x18, 0x30, 0x0c, + 0x02, 0xea, 0x02, 0x00, + 0xff, 0xea, 0xac, 0x0a, + 0x80, 0x18, 0x30, 0x04, + 0x40, 0xad, 0x84, 0x78, + 0xe7, 0xad, 0x5a, 0x09, + 0xff, 0xea, 0xc0, 0x09, + 0x01, 0x54, 0xa9, 0x1a, + 0x00, 0x55, 0xab, 0x22, + 0x01, 0x94, 0x6d, 0x33, + 0xff, 0xea, 0x20, 0x0b, + 0x04, 0xac, 0x49, 0x32, + 0xff, 0xea, 0x5a, 0x03, + 0xff, 0xea, 0x5e, 0x03, + 0x01, 0x10, 0xd4, 0x31, + 0x02, 0xa8, 0x40, 0x31, + 0x01, 0x92, 0xc1, 0x31, + 0x3d, 0x93, 0xc5, 0x29, + 0xfe, 0xe2, 0xc4, 0x09, + 0x01, 0xea, 0xc6, 0x01, + 0x02, 0xe2, 0xc8, 0x31, + 0x02, 0xec, 0x50, 0x31, + 0x02, 0xa0, 0xda, 0x31, + 0xff, 0xa9, 0x10, 0x71, + 0x10, 0xe0, 0x0e, 0x79, + 0x10, 0x92, 0x0f, 0x79, + 0x01, 0x4d, 0x9b, 0x02, + 0x02, 0xa0, 0xc0, 0x32, + 0x01, 0x93, 0xc5, 0x36, + 0x02, 0xa0, 0x58, 0x37, + 0xff, 0x21, 0x19, 0x71, + 0x02, 0x22, 0x51, 0x31, + 0x02, 0xa0, 0x5c, 0x33, + 0x02, 0xa0, 0x44, 0x36, + 0x02, 0xa0, 0x40, 0x32, + 0x02, 0xa0, 0x44, 0x36, + 0x05, 0x4d, 0x21, 0x69, + 0x40, 0x16, 0x52, 0x69, + 0xff, 0x2d, 0x57, 0x61, + 0xff, 0x29, 0x85, 0x70, + 0x02, 0x28, 0x55, 0x32, + 0x01, 0xea, 0x5a, 0x01, + 0x04, 0x44, 0xf9, 0x30, + 0x01, 0x44, 0xc1, 0x31, + 0x02, 0x28, 0x51, 0x31, + 0x02, 0xa8, 0x60, 0x31, + 0x01, 0xa4, 0x61, 0x31, + 0x01, 0x3d, 0x61, 0x31, + 0x01, 0x14, 0xd4, 0x31, + 0x01, 0x56, 0xad, 0x1a, + 0xff, 0x54, 0xa9, 0x1a, + 0xff, 0x55, 0xab, 0x22, + 0xff, 0x8d, 0x4b, 0x71, + 0x80, 0xac, 0x4a, 0x71, + 0x20, 0x16, 0x4a, 0x69, + 0x00, 0xac, 0xc4, 0x19, + 0x07, 0xe2, 0x4a, 0xf9, + 0x02, 0x8c, 0x51, 0x31, + 0x00, 0xe2, 0x2e, 0x41, + 0x01, 0xac, 0x08, 0x31, + 0x09, 0xea, 0x5a, 0x01, + 0x02, 0x8c, 0x51, 0x32, + 0xff, 0xea, 0x1a, 0x07, + 0x04, 0x24, 0xf9, 0x30, + 0x1d, 0xea, 0x5c, 0x41, + 0x02, 0x2c, 0x51, 0x31, + 0x04, 0xa8, 0xf9, 0x30, + 0x19, 0xea, 0x5c, 0x41, + 0x06, 0xea, 0x08, 0x81, + 0x01, 0xe2, 0x5a, 0x35, + 0x02, 0xf2, 0xf0, 0x31, + 0xff, 0xea, 0xd4, 0x0d, + 0x02, 0xf2, 0xf0, 0x31, + 0x02, 0xf8, 0xe4, 0x35, + 0x80, 0xea, 0xb2, 0x01, + 0x01, 0xe2, 0x00, 0x30, + 0xff, 0xea, 0xb2, 0x0d, + 0x01, 0xe2, 0x04, 0x30, + 0x01, 0xea, 0x04, 0x34, + 0x02, 0x20, 0xbd, 0x30, + 0x02, 0x20, 0xb9, 0x30, + 0x02, 0x20, 0x51, 0x31, + 0x4c, 0x93, 0xd7, 0x28, + 0x10, 0x92, 0x81, 0x79, + 0x01, 0x6b, 0xc0, 0x30, + 0x02, 0x64, 0xc8, 0x00, + 0x40, 0x3a, 0x74, 0x04, + 0x00, 0xe2, 0x76, 0x58, + 0x33, 0xea, 0x68, 0x59, + 0x33, 0xea, 0x00, 0x00, + 0x30, 0x3f, 0xc0, 0x09, + 0x30, 0xe0, 0x82, 0x61, + 0x20, 0x3f, 0x98, 0x69, + 0x10, 0x3f, 0x82, 0x79, + 0x02, 0xea, 0x7e, 0x00, + 0x00, 0xea, 0x68, 0x59, + 0x01, 0xea, 0x00, 0x30, + 0x02, 0x4e, 0x51, 0x35, + 0x01, 0xea, 0x7e, 0x00, + 0x11, 0xea, 0x68, 0x59, + 0x11, 0xea, 0x00, 0x00, + 0x02, 0x4e, 0x51, 0x35, + 0xc0, 0x4a, 0x94, 0x00, + 0x04, 0x41, 0xa6, 0x79, + 0x08, 0xea, 0x98, 0x00, + 0x08, 0x57, 0xae, 0x00, + 0x08, 0x3c, 0x78, 0x00, + 0xf0, 0x49, 0x74, 0x0a, + 0x0f, 0x67, 0xc0, 0x09, + 0x00, 0x3a, 0x75, 0x02, + 0x20, 0xea, 0x96, 0x00, + 0x00, 0xe2, 0x28, 0x42, + 0xc0, 0x4a, 0x94, 0x00, + 0x40, 0x3a, 0xd2, 0x69, + 0x02, 0x55, 0x06, 0x68, + 0x02, 0x56, 0xd2, 0x69, + 0xff, 0x5b, 0xd2, 0x61, + 0x02, 0x20, 0x51, 0x31, + 0x80, 0xea, 0xb2, 0x01, + 0x44, 0xea, 0x00, 0x00, + 0x01, 0x33, 0xc0, 0x31, + 0x33, 0xea, 0x00, 0x00, + 0xff, 0xea, 0xb2, 0x09, + 0xff, 0xe0, 0xc0, 0x19, + 0xff, 0xe0, 0xd4, 0x79, + 0x02, 0xac, 0x51, 0x31, + 0x00, 0xe2, 0xca, 0x41, + 0x02, 0x5e, 0x50, 0x31, + 0x02, 0xa8, 0xb8, 0x30, + 0x02, 0x5c, 0x50, 0x31, + 0xff, 0xad, 0xe5, 0x71, + 0x02, 0xac, 0x41, 0x31, + 0x02, 0x22, 0x51, 0x31, + 0x02, 0xa0, 0x5c, 0x33, + 0x02, 0xa0, 0x44, 0x32, + 0x00, 0xe2, 0xf8, 0x41, + 0x01, 0x4d, 0xf1, 0x79, + 0x01, 0x62, 0xc1, 0x31, + 0x00, 0x93, 0xf1, 0x61, + 0xfe, 0x4d, 0x9b, 0x0a, + 0x02, 0x60, 0x41, 0x31, + 0x00, 0xe2, 0xdc, 0x41, + 0x3d, 0x93, 0xc9, 0x29, + 0x01, 0xe4, 0xc8, 0x01, + 0x01, 0xea, 0xca, 0x01, + 0xff, 0xea, 0xda, 0x01, + 0x02, 0x20, 0x51, 0x31, + 0x02, 0xae, 0x41, 0x32, + 0xff, 0x21, 0x01, 0x62, + 0xff, 0xea, 0x46, 0x02, + 0x02, 0x5c, 0x50, 0x31, + 0x40, 0xea, 0x96, 0x00, + 0x02, 0x56, 0x20, 0x6e, + 0x01, 0x55, 0x20, 0x6e, + 0x10, 0x92, 0x0d, 0x7a, + 0x10, 0x40, 0x16, 0x6a, + 0x01, 0x56, 0x16, 0x7a, + 0xff, 0x97, 0x07, 0x78, + 0x13, 0xea, 0x6e, 0x59, + 0x13, 0xea, 0x04, 0x00, + 0x00, 0xe2, 0x06, 0x40, + 0xbf, 0x3a, 0x74, 0x08, + 0x04, 0x41, 0x1c, 0x7a, + 0x08, 0xea, 0x98, 0x00, + 0x08, 0x57, 0xae, 0x00, + 0x01, 0x93, 0x75, 0x32, + 0x01, 0x94, 0x77, 0x32, + 0x40, 0xea, 0x72, 0x02, + 0x08, 0x3c, 0x78, 0x00, + 0x80, 0xea, 0x6e, 0x02, + 0x00, 0xe2, 0xf6, 0x5b, + 0x01, 0x3c, 0xc1, 0x31, + 0x9f, 0xe0, 0x98, 0x7c, + 0x80, 0xe0, 0x3c, 0x72, + 0xa0, 0xe0, 0x78, 0x72, + 0xc0, 0xe0, 0x6e, 0x72, + 0xe0, 0xe0, 0xa8, 0x72, + 0x01, 0xea, 0x6e, 0x59, + 0x01, 0xea, 0x04, 0x00, + 0x00, 0xe2, 0x28, 0x42, + 0x80, 0x39, 0x43, 0x7a, + 0x03, 0xea, 0x6e, 0x59, + 0x03, 0xea, 0x04, 0x00, + 0xee, 0x00, 0x4a, 0x6a, + 0x05, 0xea, 0xb4, 0x00, + 0x33, 0xea, 0x68, 0x59, + 0x33, 0xea, 0x00, 0x00, + 0x02, 0xa8, 0x9c, 0x32, + 0x00, 0xe2, 0x88, 0x59, + 0xef, 0x96, 0xd5, 0x19, + 0x00, 0xe2, 0x5a, 0x52, + 0x09, 0x80, 0xe1, 0x30, + 0x02, 0xea, 0x36, 0x00, + 0xa8, 0xea, 0x32, 0x00, + 0x00, 0xe2, 0x60, 0x42, + 0x01, 0x96, 0xd1, 0x30, + 0x10, 0x80, 0x89, 0x31, + 0x20, 0xea, 0x32, 0x00, + 0xbf, 0x39, 0x73, 0x0a, + 0x10, 0x4c, 0x6a, 0x6a, + 0x20, 0x19, 0x62, 0x6a, + 0x20, 0x19, 0x66, 0x6a, + 0x02, 0x4d, 0x28, 0x6a, + 0x40, 0x39, 0x73, 0x02, + 0x00, 0xe2, 0x28, 0x42, + 0x80, 0x39, 0xe9, 0x6a, + 0x01, 0x44, 0x10, 0x33, + 0x08, 0x92, 0x25, 0x03, + 0x00, 0xe2, 0x28, 0x42, + 0x10, 0xea, 0x80, 0x00, + 0x01, 0x37, 0xc5, 0x31, + 0x80, 0xe2, 0x94, 0x62, + 0x10, 0x92, 0xb9, 0x6a, + 0xc0, 0x94, 0xc5, 0x01, + 0x40, 0x92, 0x85, 0x6a, + 0xbf, 0xe2, 0xc4, 0x09, + 0x20, 0x92, 0x99, 0x7a, + 0x01, 0xe2, 0x88, 0x30, + 0x00, 0xe2, 0xf6, 0x5b, + 0xa0, 0x3c, 0xa1, 0x62, + 0x23, 0x92, 0x89, 0x08, + 0x00, 0xe2, 0xf6, 0x5b, + 0xa0, 0x3c, 0xa1, 0x62, + 0x00, 0xa8, 0x98, 0x42, + 0xff, 0xe2, 0x98, 0x62, + 0x00, 0xe2, 0xb8, 0x42, + 0x40, 0xea, 0x98, 0x00, + 0x01, 0xe2, 0x88, 0x30, + 0x00, 0xe2, 0xf6, 0x5b, + 0xa0, 0x3c, 0x77, 0x72, + 0x40, 0xea, 0x98, 0x00, + 0x01, 0x37, 0x95, 0x32, + 0x08, 0xea, 0x6e, 0x02, + 0x00, 0xe2, 0x28, 0x42, + 0xe0, 0xea, 0x12, 0x5c, + 0x80, 0xe0, 0xf4, 0x6a, + 0x04, 0xe0, 0xa6, 0x73, + 0x02, 0xe0, 0xd8, 0x73, + 0x00, 0xea, 0x52, 0x73, + 0x03, 0xe0, 0xe8, 0x73, + 0x23, 0xe0, 0xca, 0x72, + 0x08, 0xe0, 0xf0, 0x72, + 0x00, 0xe2, 0xf6, 0x5b, + 0x07, 0xea, 0x6e, 0x59, + 0x07, 0xea, 0x04, 0x00, + 0x08, 0x48, 0x29, 0x72, + 0x04, 0x48, 0xc7, 0x62, + 0x01, 0x49, 0x89, 0x30, + 0x00, 0xe2, 0xb8, 0x42, + 0x01, 0x44, 0xd4, 0x31, + 0x00, 0xe2, 0xb8, 0x42, + 0x01, 0x00, 0x6c, 0x32, + 0x33, 0xea, 0x68, 0x59, + 0x33, 0xea, 0x00, 0x00, + 0x4c, 0x3a, 0xc1, 0x28, + 0x01, 0x64, 0xc0, 0x31, + 0x00, 0x36, 0x69, 0x59, + 0x01, 0x36, 0x01, 0x30, + 0x01, 0xe0, 0xee, 0x7a, + 0xa0, 0xea, 0x08, 0x5c, + 0x01, 0xa0, 0xee, 0x62, + 0x01, 0x84, 0xe3, 0x7a, + 0x01, 0x95, 0xf1, 0x6a, + 0x05, 0xea, 0x6e, 0x59, + 0x05, 0xea, 0x04, 0x00, + 0x00, 0xe2, 0xf0, 0x42, + 0x03, 0xea, 0x6e, 0x59, + 0x03, 0xea, 0x04, 0x00, + 0x00, 0xe2, 0xf0, 0x42, + 0x07, 0xea, 0x1a, 0x5c, + 0x01, 0x44, 0xd4, 0x31, + 0x00, 0xe2, 0x28, 0x42, + 0x3f, 0xe0, 0x76, 0x0a, + 0xc0, 0x3a, 0xc1, 0x09, + 0x00, 0x3b, 0x51, 0x01, + 0xff, 0xea, 0x52, 0x09, + 0x30, 0x3a, 0xc5, 0x09, + 0x3d, 0xe2, 0xc4, 0x29, + 0xb8, 0xe2, 0xc4, 0x19, + 0x01, 0xea, 0xc6, 0x01, + 0x02, 0xe2, 0xc8, 0x31, + 0x02, 0xec, 0x40, 0x31, + 0xff, 0xa1, 0x10, 0x73, + 0x02, 0xe8, 0xda, 0x31, + 0x02, 0xa0, 0x50, 0x31, + 0x00, 0xe2, 0x32, 0x43, + 0x80, 0x39, 0x73, 0x02, + 0x01, 0x44, 0xd4, 0x31, + 0x00, 0xe2, 0xf6, 0x5b, + 0x01, 0x39, 0x73, 0x02, + 0xe0, 0x3c, 0x4d, 0x63, + 0x02, 0x39, 0x73, 0x02, + 0x20, 0x46, 0x46, 0x63, + 0xff, 0xea, 0x52, 0x09, + 0xa8, 0xea, 0x08, 0x5c, + 0x04, 0x92, 0x2d, 0x7b, + 0x01, 0x3a, 0xc1, 0x31, + 0x00, 0x93, 0x2d, 0x63, + 0x01, 0x3b, 0xc1, 0x31, + 0x00, 0x94, 0x37, 0x73, + 0x01, 0xa9, 0x52, 0x11, + 0xff, 0xa9, 0x22, 0x6b, + 0x00, 0xe2, 0x46, 0x43, + 0x10, 0x39, 0x73, 0x02, + 0x04, 0x92, 0x47, 0x7b, + 0xfb, 0x92, 0x25, 0x0b, + 0xff, 0xea, 0x72, 0x0a, + 0x01, 0xa4, 0x41, 0x6b, + 0x02, 0xa8, 0x9c, 0x32, + 0x00, 0xe2, 0x88, 0x59, + 0x10, 0x92, 0xf1, 0x7a, + 0xff, 0xea, 0x1a, 0x5c, + 0x00, 0xe2, 0xf0, 0x42, + 0x04, 0xea, 0x6e, 0x59, + 0x04, 0xea, 0x04, 0x00, + 0x00, 0xe2, 0xf0, 0x42, + 0x04, 0xea, 0x6e, 0x59, + 0x04, 0xea, 0x04, 0x00, + 0x00, 0xe2, 0x28, 0x42, + 0x08, 0x92, 0xe9, 0x7a, + 0xc0, 0x39, 0x5d, 0x7b, + 0x80, 0x39, 0xe9, 0x6a, + 0xff, 0x88, 0x5d, 0x6b, + 0x40, 0x39, 0xe9, 0x6a, + 0x10, 0x92, 0x63, 0x7b, + 0x0a, 0xea, 0x6e, 0x59, + 0x0a, 0xea, 0x04, 0x00, + 0x00, 0xe2, 0x82, 0x5b, + 0x00, 0xe2, 0xc2, 0x43, + 0x50, 0x4b, 0x6a, 0x6b, + 0xbf, 0x3a, 0x74, 0x08, + 0x01, 0xe0, 0xf4, 0x31, + 0xff, 0xea, 0xc0, 0x09, + 0x01, 0x32, 0x65, 0x1a, + 0x00, 0x33, 0x67, 0x22, + 0x04, 0x4d, 0x9b, 0x02, + 0x01, 0xfa, 0xc0, 0x35, + 0x02, 0xa8, 0x90, 0x32, + 0x02, 0xea, 0xb4, 0x00, + 0x33, 0xea, 0x68, 0x59, + 0x33, 0xea, 0x00, 0x00, + 0x02, 0x48, 0x51, 0x31, + 0xff, 0x90, 0x85, 0x68, + 0xff, 0x88, 0x8f, 0x6b, + 0x01, 0xa4, 0x8b, 0x6b, + 0x02, 0xa4, 0x93, 0x6b, + 0x01, 0x84, 0x93, 0x7b, + 0x02, 0x28, 0x19, 0x33, + 0x02, 0xa8, 0x50, 0x36, + 0xff, 0x88, 0x93, 0x73, + 0x00, 0xe2, 0x66, 0x5b, + 0x02, 0xa8, 0x20, 0x33, + 0x04, 0xa4, 0x49, 0x03, + 0xff, 0xea, 0x1a, 0x03, + 0xff, 0x2d, 0x9f, 0x63, + 0x02, 0xa8, 0x58, 0x32, + 0x02, 0xa8, 0x5c, 0x36, + 0x02, 0xa8, 0x40, 0x31, + 0x02, 0x2e, 0x51, 0x31, + 0x02, 0xa0, 0x18, 0x33, + 0x02, 0xa0, 0x5c, 0x36, + 0xc0, 0x39, 0xe9, 0x6a, + 0x04, 0x92, 0x25, 0x03, + 0x20, 0x92, 0xc3, 0x6b, + 0x02, 0xa8, 0x40, 0x31, + 0xc0, 0x3a, 0xc1, 0x09, + 0x00, 0x3b, 0x51, 0x01, + 0xff, 0xea, 0x52, 0x09, + 0x30, 0x3a, 0xc5, 0x09, + 0x3d, 0xe2, 0xc4, 0x29, + 0xb8, 0xe2, 0xc4, 0x19, + 0x01, 0xea, 0xc6, 0x01, + 0x02, 0xe2, 0xc8, 0x31, + 0x02, 0xa0, 0xda, 0x31, + 0x02, 0xa0, 0x50, 0x31, + 0xf7, 0x57, 0xae, 0x08, + 0x08, 0xea, 0x98, 0x00, + 0x01, 0x44, 0xd4, 0x31, + 0xee, 0x00, 0xcc, 0x6b, + 0x02, 0xea, 0xb4, 0x00, + 0xc0, 0xea, 0x72, 0x02, + 0x09, 0x4c, 0xce, 0x7b, + 0x01, 0xea, 0x78, 0x02, + 0x08, 0x4c, 0x06, 0x68, + 0x0b, 0xea, 0x6e, 0x59, + 0x0b, 0xea, 0x04, 0x00, + 0x01, 0x44, 0xd4, 0x31, + 0x20, 0x39, 0x29, 0x7a, + 0x00, 0xe2, 0xe0, 0x5b, + 0x00, 0xe2, 0x28, 0x42, + 0x01, 0x84, 0xe5, 0x7b, + 0x01, 0xa4, 0x49, 0x07, + 0x08, 0x60, 0x30, 0x33, + 0x08, 0x80, 0x41, 0x37, + 0xdf, 0x39, 0x73, 0x0a, + 0xee, 0x00, 0xf2, 0x6b, + 0x05, 0xea, 0xb4, 0x00, + 0x33, 0xea, 0x68, 0x59, + 0x33, 0xea, 0x00, 0x00, + 0x00, 0xe2, 0x88, 0x59, + 0x00, 0xe2, 0xf0, 0x42, + 0xff, 0x42, 0x02, 0x6c, + 0x01, 0x41, 0xf6, 0x6b, + 0x02, 0x41, 0xf6, 0x7b, + 0xff, 0x42, 0x02, 0x6c, + 0x01, 0x41, 0xf6, 0x6b, + 0x02, 0x41, 0xf6, 0x7b, + 0xff, 0x42, 0x02, 0x7c, + 0x04, 0x4c, 0xf6, 0x6b, + 0xe0, 0x41, 0x78, 0x0e, + 0x01, 0x44, 0xd4, 0x31, + 0xff, 0x42, 0x0a, 0x7c, + 0x04, 0x4c, 0x0a, 0x6c, + 0xe0, 0x41, 0x78, 0x0a, + 0xe0, 0x3c, 0x29, 0x62, + 0xff, 0xea, 0xca, 0x09, + 0x01, 0xe2, 0xc8, 0x31, + 0x01, 0x46, 0xda, 0x35, + 0x01, 0x44, 0xd4, 0x35, + 0x10, 0xea, 0x80, 0x00, + 0x01, 0xe2, 0x6e, 0x36, + 0x04, 0xa6, 0x22, 0x7c, + 0xff, 0xea, 0x5a, 0x09, + 0xff, 0xea, 0x4c, 0x0d, + 0x01, 0xa6, 0x4e, 0x6c, + 0x10, 0xad, 0x84, 0x78, + 0x80, 0xad, 0x46, 0x6c, + 0x08, 0xad, 0x84, 0x68, + 0x20, 0x19, 0x3a, 0x7c, + 0x80, 0xea, 0xb2, 0x01, + 0x11, 0x00, 0x00, 0x10, + 0x02, 0xa6, 0x36, 0x7c, + 0xff, 0xea, 0xb2, 0x0d, + 0x11, 0x00, 0x00, 0x10, + 0xff, 0xea, 0xb2, 0x09, + 0x04, 0x84, 0xf9, 0x30, + 0x00, 0xea, 0x08, 0x81, + 0xff, 0xea, 0xd4, 0x09, + 0x02, 0x84, 0xf9, 0x88, + 0x0d, 0xea, 0x5a, 0x01, + 0x04, 0xa6, 0x4c, 0x05, + 0x04, 0xa6, 0x84, 0x78, + 0xff, 0xea, 0x5a, 0x09, + 0x03, 0x84, 0x59, 0x89, + 0x03, 0xea, 0x4c, 0x01, + 0x80, 0x1a, 0x84, 0x78, + 0x08, 0x19, 0x84, 0x78, + 0x08, 0xb0, 0xe0, 0x30, + 0x04, 0xb0, 0xe0, 0x30, + 0x03, 0xb0, 0xf0, 0x30, + 0x01, 0xb0, 0x06, 0x33, + 0x7f, 0x83, 0xe9, 0x08, + 0x04, 0xac, 0x58, 0x19, + 0xff, 0xea, 0xc0, 0x09, + 0x04, 0x84, 0x09, 0x9b, + 0x00, 0x85, 0x0b, 0x23, + 0x00, 0x86, 0x0d, 0x23, + 0x00, 0x87, 0x0f, 0x23, + 0x01, 0x84, 0xc5, 0x31, + 0x80, 0x83, 0x71, 0x7c, + 0x02, 0xe2, 0xc4, 0x01, + 0xff, 0xea, 0x4c, 0x09, + 0x01, 0xe2, 0x36, 0x30, + 0xc8, 0x19, 0x32, 0x00, + 0x88, 0x19, 0x32, 0x00, + 0x01, 0xac, 0xd4, 0x99, + 0x00, 0xe2, 0x84, 0x50, + 0xfe, 0xa6, 0x4c, 0x0d, + 0x0b, 0x98, 0xe1, 0x30, + 0xfd, 0xa4, 0x49, 0x09, + 0x80, 0xa3, 0x85, 0x7c, + 0x02, 0xa4, 0x48, 0x01, + 0x01, 0xa4, 0x36, 0x30, + 0xa8, 0xea, 0x32, 0x00, + 0xfd, 0xa4, 0x49, 0x0b, + 0x05, 0xa3, 0x07, 0x33, + 0x80, 0x83, 0x91, 0x6c, + 0x02, 0xea, 0x4c, 0x05, + 0xff, 0xea, 0x4c, 0x0d, + 0x00, 0xe2, 0x60, 0x59, + 0x02, 0xa6, 0x24, 0x6c, + 0x80, 0xf9, 0xf2, 0x05, + 0xc0, 0x39, 0x9f, 0x7c, + 0x03, 0xea, 0x6e, 0x59, + 0x03, 0xea, 0x04, 0x00, + 0x20, 0x39, 0xc3, 0x7c, + 0x01, 0x84, 0xa9, 0x6c, + 0x06, 0xea, 0x6e, 0x59, + 0x06, 0xea, 0x04, 0x00, + 0x00, 0xe2, 0xc6, 0x44, + 0x01, 0x00, 0x6c, 0x32, + 0xee, 0x00, 0xb2, 0x6c, + 0x05, 0xea, 0xb4, 0x00, + 0x33, 0xea, 0x68, 0x59, + 0x33, 0xea, 0x00, 0x00, + 0x80, 0x3d, 0x7a, 0x00, + 0xfc, 0x42, 0xb4, 0x7c, + 0x7f, 0x3d, 0x7a, 0x08, + 0x00, 0x36, 0x69, 0x59, + 0x01, 0x36, 0x01, 0x30, + 0x09, 0xea, 0x6e, 0x59, + 0x09, 0xea, 0x04, 0x00, + 0x00, 0xe2, 0x28, 0x42, + 0x01, 0xa4, 0xa9, 0x6c, + 0x00, 0xe2, 0x7c, 0x5c, + 0x20, 0x39, 0x73, 0x02, + 0x01, 0x00, 0x6c, 0x32, + 0x02, 0xa6, 0xce, 0x7c, + 0x00, 0xe2, 0x92, 0x5c, + 0x00, 0xe2, 0x76, 0x58, + 0x00, 0xe2, 0x86, 0x58, + 0x00, 0xe2, 0x5a, 0x58, + 0x00, 0x36, 0x69, 0x59, + 0x01, 0x36, 0x01, 0x30, + 0x20, 0x19, 0xce, 0x6c, + 0x00, 0xe2, 0xfe, 0x5c, + 0x04, 0x19, 0xe8, 0x6c, + 0x02, 0x19, 0x32, 0x00, + 0x01, 0x84, 0xe9, 0x7c, + 0x01, 0x1b, 0xe2, 0x7c, + 0x01, 0x1a, 0xe8, 0x6c, + 0x00, 0xe2, 0x98, 0x44, + 0x80, 0x4b, 0xee, 0x6c, + 0x01, 0x4c, 0xea, 0x7c, + 0x03, 0x42, 0x98, 0x6c, + 0x00, 0xe2, 0x1e, 0x5c, + 0x80, 0xf9, 0xf2, 0x01, + 0x04, 0x39, 0x29, 0x7a, + 0x00, 0xe2, 0x28, 0x42, + 0x08, 0x5d, 0x06, 0x6d, + 0x00, 0xe2, 0x76, 0x58, + 0x00, 0x36, 0x69, 0x59, + 0x01, 0x36, 0x01, 0x30, + 0x02, 0x1b, 0xf6, 0x7c, + 0x08, 0x5d, 0x04, 0x7d, + 0x03, 0x68, 0x00, 0x37, + 0x01, 0x84, 0x09, 0x07, + 0x80, 0x1b, 0x10, 0x7d, + 0x80, 0x84, 0x11, 0x6d, + 0xff, 0x85, 0x0b, 0x1b, + 0xff, 0x86, 0x0d, 0x23, + 0xff, 0x87, 0x0f, 0x23, + 0xf8, 0x1b, 0x08, 0x0b, + 0xff, 0xea, 0x06, 0x0b, + 0x03, 0x68, 0x00, 0x37, + 0x00, 0xe2, 0xd6, 0x58, + 0x10, 0xea, 0x18, 0x00, + 0xf9, 0xd9, 0xb2, 0x0d, + 0x01, 0xd9, 0xb2, 0x05, + 0x01, 0x52, 0x48, 0x31, + 0x20, 0xa4, 0x3a, 0x7d, + 0x20, 0x5b, 0x3a, 0x7d, + 0x80, 0xf9, 0x48, 0x7d, + 0x02, 0xea, 0xb4, 0x00, + 0x11, 0x00, 0x00, 0x10, + 0x04, 0x19, 0x54, 0x7d, + 0xdf, 0x19, 0x32, 0x08, + 0x60, 0x5b, 0x54, 0x6d, + 0x01, 0x4c, 0x2e, 0x7d, + 0x20, 0x19, 0x32, 0x00, + 0x01, 0xd9, 0xb2, 0x05, + 0x02, 0xea, 0xb4, 0x00, + 0x01, 0xd9, 0xb2, 0x05, + 0x10, 0x5b, 0x4c, 0x6d, + 0x08, 0x5b, 0x56, 0x6d, + 0x20, 0x5b, 0x46, 0x6d, + 0x02, 0x5b, 0x76, 0x6d, + 0x0e, 0xea, 0x6e, 0x59, + 0x0e, 0xea, 0x04, 0x00, + 0x80, 0xf9, 0x36, 0x6d, + 0xdf, 0x5c, 0xb8, 0x08, + 0x01, 0xd9, 0xb2, 0x05, + 0x01, 0xa4, 0x37, 0x6e, + 0x00, 0xe2, 0x7c, 0x5c, + 0x00, 0xe2, 0x80, 0x5d, + 0x01, 0x90, 0x21, 0x1b, + 0x01, 0xd9, 0xb2, 0x05, + 0x00, 0xe2, 0x66, 0x5b, + 0xf3, 0x96, 0xd5, 0x19, + 0x00, 0xe2, 0x64, 0x55, + 0x80, 0x96, 0x65, 0x6d, + 0x0f, 0xea, 0x6e, 0x59, + 0x0f, 0xea, 0x04, 0x00, + 0x00, 0xe2, 0x6c, 0x45, + 0x04, 0x8c, 0xe1, 0x30, + 0x01, 0xea, 0xf2, 0x00, + 0x02, 0xea, 0x36, 0x00, + 0xa8, 0xea, 0x32, 0x00, + 0xff, 0x97, 0x73, 0x7d, + 0x14, 0xea, 0x6e, 0x59, + 0x14, 0xea, 0x04, 0x00, + 0x00, 0xe2, 0xe2, 0x5d, + 0x01, 0xd9, 0xb2, 0x05, + 0x09, 0x80, 0xe1, 0x30, + 0x02, 0xea, 0x36, 0x00, + 0xa8, 0xea, 0x32, 0x00, + 0x00, 0xe2, 0xda, 0x5d, + 0x01, 0xd9, 0xb2, 0x05, + 0x02, 0xa6, 0x90, 0x7d, + 0x00, 0xe2, 0x60, 0x59, + 0x20, 0x5b, 0x9e, 0x6d, + 0xfc, 0x42, 0x8a, 0x7d, + 0x10, 0x40, 0x8c, 0x6d, + 0x20, 0x4d, 0x8e, 0x7d, + 0x08, 0x5d, 0x9e, 0x6d, + 0x02, 0xa6, 0x24, 0x6c, + 0x00, 0xe2, 0x60, 0x59, + 0x20, 0x5b, 0x9e, 0x6d, + 0x01, 0x1b, 0xbe, 0x6d, + 0xfc, 0x42, 0x9a, 0x7d, + 0x10, 0x40, 0x9c, 0x6d, + 0x20, 0x4d, 0x84, 0x78, + 0x08, 0x5d, 0x84, 0x78, + 0x02, 0x19, 0x32, 0x00, + 0x01, 0x5b, 0x40, 0x31, + 0x00, 0xe2, 0xfe, 0x5c, + 0x00, 0xe2, 0xe0, 0x5b, + 0x20, 0xea, 0xb6, 0x00, + 0x00, 0xe2, 0x1e, 0x5c, + 0x20, 0x5c, 0xb8, 0x00, + 0x04, 0x19, 0xb4, 0x6d, + 0x01, 0x1a, 0xb4, 0x6d, + 0x00, 0xe2, 0x60, 0x59, + 0x01, 0x1a, 0x84, 0x78, + 0x80, 0xf9, 0xf2, 0x01, + 0x20, 0xa0, 0x18, 0x7e, + 0xff, 0x90, 0x21, 0x1b, + 0x08, 0x92, 0x77, 0x6b, + 0x02, 0xea, 0xb4, 0x04, + 0x01, 0xa4, 0x49, 0x03, + 0x40, 0x5b, 0xce, 0x6d, + 0x00, 0xe2, 0x60, 0x59, + 0x40, 0x5b, 0xce, 0x6d, + 0x04, 0x5d, 0x38, 0x7e, + 0x01, 0x1a, 0x38, 0x7e, + 0x20, 0x4d, 0x84, 0x78, + 0x40, 0x5b, 0x18, 0x7e, + 0x04, 0x5d, 0x38, 0x7e, + 0x01, 0x1a, 0x38, 0x7e, + 0x80, 0xf9, 0xf2, 0x01, + 0xff, 0x90, 0x21, 0x1b, + 0x08, 0x92, 0x77, 0x6b, + 0x02, 0xea, 0xb4, 0x04, + 0x00, 0xe2, 0x60, 0x59, + 0x01, 0x1b, 0x84, 0x78, + 0x80, 0xf9, 0xf2, 0x01, + 0x02, 0xea, 0xb4, 0x04, + 0x00, 0xe2, 0x60, 0x59, + 0x01, 0x1b, 0xf6, 0x6d, + 0x40, 0x5b, 0x04, 0x7e, + 0x01, 0x1b, 0xf6, 0x6d, + 0x02, 0x19, 0x32, 0x00, + 0x01, 0x1a, 0x84, 0x78, + 0x80, 0xf9, 0xf2, 0x01, + 0xff, 0xea, 0x10, 0x03, + 0x08, 0x92, 0x25, 0x03, + 0x00, 0xe2, 0x76, 0x43, + 0x01, 0x1a, 0x00, 0x7e, + 0x40, 0x5b, 0xfc, 0x7d, + 0x01, 0x1a, 0xea, 0x6d, + 0xfc, 0x42, 0x84, 0x78, + 0x01, 0x1a, 0x04, 0x6e, + 0x10, 0xea, 0x6e, 0x59, + 0x10, 0xea, 0x04, 0x00, + 0xfc, 0x42, 0x84, 0x78, + 0x10, 0x40, 0x0a, 0x6e, + 0x20, 0x4d, 0x84, 0x78, + 0x40, 0x5b, 0xea, 0x6d, + 0x01, 0x1a, 0x84, 0x78, + 0x01, 0x90, 0x21, 0x1b, + 0x30, 0x3f, 0xc0, 0x09, + 0x30, 0xe0, 0x84, 0x60, + 0x40, 0x4b, 0x84, 0x68, + 0xff, 0xea, 0x52, 0x01, + 0xee, 0x00, 0x20, 0x6e, + 0x80, 0xf9, 0xf2, 0x01, + 0xff, 0x90, 0x21, 0x1b, + 0x02, 0xea, 0xb4, 0x00, + 0x20, 0xea, 0x9a, 0x00, + 0x04, 0x41, 0x26, 0x7e, + 0x08, 0xea, 0x98, 0x00, + 0x08, 0x57, 0xae, 0x00, + 0xf3, 0x42, 0x30, 0x6e, + 0x12, 0xea, 0x6e, 0x59, + 0x12, 0xea, 0x04, 0x00, + 0x00, 0xe2, 0x28, 0x42, + 0x0d, 0xea, 0x6e, 0x59, + 0x0d, 0xea, 0x04, 0x00, + 0x00, 0xe2, 0x28, 0x42, + 0x01, 0x90, 0x21, 0x1b, + 0x11, 0xea, 0x6e, 0x59, + 0x11, 0xea, 0x04, 0x00, + 0x00, 0xe2, 0x66, 0x5b, + 0x08, 0x5a, 0xb4, 0x00, + 0x00, 0xe2, 0x5e, 0x5e, + 0xa8, 0xea, 0x32, 0x00, + 0x00, 0xe2, 0x60, 0x59, + 0x80, 0x1a, 0x4c, 0x7e, + 0x00, 0xe2, 0x5e, 0x5e, + 0x80, 0x19, 0x32, 0x00, + 0x40, 0x5b, 0x52, 0x6e, + 0x08, 0x5a, 0x52, 0x7e, + 0x20, 0x4d, 0x84, 0x78, + 0x02, 0x84, 0x09, 0x03, + 0x40, 0x5b, 0x18, 0x7e, + 0xff, 0x90, 0x21, 0x1b, + 0x80, 0xf9, 0xf2, 0x01, + 0x08, 0x92, 0x77, 0x6b, + 0x02, 0xea, 0xb4, 0x04, + 0x01, 0x40, 0xe1, 0x30, + 0x05, 0x41, 0xe3, 0x98, + 0x01, 0xe0, 0xf4, 0x31, + 0xff, 0xea, 0xc0, 0x09, + 0x00, 0x42, 0xe5, 0x20, + 0x00, 0x43, 0xe7, 0x20, + 0x01, 0xfa, 0xc0, 0x31, + 0x04, 0xea, 0xe8, 0x30, + 0xff, 0xea, 0xf0, 0x08, + 0x02, 0xea, 0xf2, 0x00, + 0xff, 0xea, 0xf4, 0x0c +}; + +typedef int ahd_patch_func_t (struct ahd_softc *ahd); +static ahd_patch_func_t ahd_patch23_func; + +static int +ahd_patch23_func(struct ahd_softc *ahd) +{ + return ((ahd->bugs & AHD_PKT_BITBUCKET_BUG) != 0); +} + +static ahd_patch_func_t ahd_patch22_func; + +static int +ahd_patch22_func(struct ahd_softc *ahd) +{ + return ((ahd->bugs & AHD_PKT_BITBUCKET_BUG) == 0); +} + +static ahd_patch_func_t ahd_patch21_func; + +static int +ahd_patch21_func(struct ahd_softc *ahd) +{ + return ((ahd->flags & AHD_INITIATORROLE) != 0); +} + +static ahd_patch_func_t ahd_patch20_func; + +static int +ahd_patch20_func(struct ahd_softc *ahd) +{ + return ((ahd->flags & AHD_TARGETROLE) != 0); +} + +static ahd_patch_func_t ahd_patch19_func; + +static int +ahd_patch19_func(struct ahd_softc *ahd) +{ + return ((ahd->bugs & AHD_AUTOFLUSH_BUG) != 0); +} + +static ahd_patch_func_t ahd_patch18_func; + +static int +ahd_patch18_func(struct ahd_softc *ahd) +{ + return ((ahd->features & AHD_NEW_DFCNTRL_OPTS) != 0); +} + +static ahd_patch_func_t ahd_patch17_func; + +static int +ahd_patch17_func(struct ahd_softc *ahd) +{ + return ((ahd->flags & AHD_39BIT_ADDRESSING) != 0); +} + +static ahd_patch_func_t ahd_patch16_func; + +static int +ahd_patch16_func(struct ahd_softc *ahd) +{ + return ((ahd->flags & AHD_64BIT_ADDRESSING) != 0); +} + +static ahd_patch_func_t ahd_patch15_func; + +static int +ahd_patch15_func(struct ahd_softc *ahd) +{ + return ((ahd->features & AHD_NEW_DFCNTRL_OPTS) == 0); +} + +static ahd_patch_func_t ahd_patch14_func; + +static int +ahd_patch14_func(struct ahd_softc *ahd) +{ + return ((ahd->bugs & AHD_REG_SLOW_SETTLE_BUG) != 0); +} + +static ahd_patch_func_t ahd_patch13_func; + +static int +ahd_patch13_func(struct ahd_softc *ahd) +{ + return ((ahd->features & AHD_RTI) == 0); +} + +static ahd_patch_func_t ahd_patch12_func; + +static int +ahd_patch12_func(struct ahd_softc *ahd) +{ + return ((ahd->bugs & AHD_EARLY_REQ_BUG) != 0); +} + +static ahd_patch_func_t ahd_patch11_func; + +static int +ahd_patch11_func(struct ahd_softc *ahd) +{ + return ((ahd->bugs & AHD_BUSFREEREV_BUG) == 0); +} + +static ahd_patch_func_t ahd_patch10_func; + +static int +ahd_patch10_func(struct ahd_softc *ahd) +{ + return ((ahd->flags & AHD_SEQUENCER_DEBUG) != 0); +} + +static ahd_patch_func_t ahd_patch9_func; + +static int +ahd_patch9_func(struct ahd_softc *ahd) +{ + return ((ahd->features & AHD_FAST_CDB_DELIVERY) != 0); +} + +static ahd_patch_func_t ahd_patch8_func; + +static int +ahd_patch8_func(struct ahd_softc *ahd) +{ + return ((ahd->bugs & AHD_LQO_ATNO_BUG) != 0); +} + +static ahd_patch_func_t ahd_patch7_func; + +static int +ahd_patch7_func(struct ahd_softc *ahd) +{ + return ((ahd->bugs & AHD_BUSFREEREV_BUG) != 0); +} + +static ahd_patch_func_t ahd_patch6_func; + +static int +ahd_patch6_func(struct ahd_softc *ahd) +{ + return ((ahd->bugs & AHD_NONPACKFIFO_BUG) != 0); +} + +static ahd_patch_func_t ahd_patch5_func; + +static int +ahd_patch5_func(struct ahd_softc *ahd) +{ + return ((ahd->bugs & AHD_SENT_SCB_UPDATE_BUG) != 0); +} + +static ahd_patch_func_t ahd_patch4_func; + +static int +ahd_patch4_func(struct ahd_softc *ahd) +{ + return ((ahd->bugs & AHD_PKT_LUN_BUG) != 0); +} + +static ahd_patch_func_t ahd_patch3_func; + +static int +ahd_patch3_func(struct ahd_softc *ahd) +{ + return ((ahd->bugs & AHD_FAINT_LED_BUG) != 0); +} + +static ahd_patch_func_t ahd_patch2_func; + +static int +ahd_patch2_func(struct ahd_softc *ahd) +{ + return ((ahd->bugs & AHD_SET_MODE_BUG) != 0); +} + +static ahd_patch_func_t ahd_patch1_func; + +static int +ahd_patch1_func(struct ahd_softc *ahd) +{ + return ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0); +} + +static ahd_patch_func_t ahd_patch0_func; + +static int +ahd_patch0_func(struct ahd_softc *ahd) +{ + return (0); +} + +static const struct patch { + ahd_patch_func_t *patch_func; + uint32_t begin :10, + skip_instr :10, + skip_patch :12; +} patches[] = { + { ahd_patch1_func, 0, 3, 3 }, + { ahd_patch1_func, 1, 1, 2 }, + { ahd_patch0_func, 2, 1, 1 }, + { ahd_patch1_func, 3, 3, 3 }, + { ahd_patch1_func, 4, 1, 2 }, + { ahd_patch0_func, 5, 1, 1 }, + { ahd_patch2_func, 6, 1, 2 }, + { ahd_patch0_func, 7, 1, 1 }, + { ahd_patch3_func, 36, 5, 1 }, + { ahd_patch2_func, 45, 1, 2 }, + { ahd_patch0_func, 46, 1, 1 }, + { ahd_patch1_func, 53, 1, 2 }, + { ahd_patch0_func, 54, 1, 1 }, + { ahd_patch2_func, 59, 1, 2 }, + { ahd_patch0_func, 60, 1, 1 }, + { ahd_patch2_func, 63, 1, 2 }, + { ahd_patch0_func, 64, 1, 1 }, + { ahd_patch2_func, 67, 1, 2 }, + { ahd_patch0_func, 68, 1, 1 }, + { ahd_patch4_func, 115, 1, 1 }, + { ahd_patch2_func, 180, 3, 1 }, + { ahd_patch1_func, 183, 2, 1 }, + { ahd_patch5_func, 185, 1, 1 }, + { ahd_patch2_func, 194, 1, 2 }, + { ahd_patch0_func, 195, 1, 1 }, + { ahd_patch6_func, 196, 2, 2 }, + { ahd_patch0_func, 198, 6, 3 }, + { ahd_patch2_func, 201, 1, 2 }, + { ahd_patch0_func, 202, 1, 1 }, + { ahd_patch2_func, 205, 1, 2 }, + { ahd_patch0_func, 206, 1, 1 }, + { ahd_patch3_func, 208, 1, 1 }, + { ahd_patch7_func, 209, 3, 1 }, + { ahd_patch3_func, 218, 1, 1 }, + { ahd_patch5_func, 219, 16, 2 }, + { ahd_patch0_func, 235, 1, 1 }, + { ahd_patch8_func, 260, 2, 1 }, + { ahd_patch1_func, 264, 1, 2 }, + { ahd_patch0_func, 265, 1, 1 }, + { ahd_patch7_func, 268, 3, 1 }, + { ahd_patch1_func, 283, 1, 2 }, + { ahd_patch0_func, 284, 1, 1 }, + { ahd_patch1_func, 287, 1, 2 }, + { ahd_patch0_func, 288, 1, 1 }, + { ahd_patch2_func, 291, 1, 2 }, + { ahd_patch0_func, 292, 1, 1 }, + { ahd_patch9_func, 305, 2, 2 }, + { ahd_patch0_func, 307, 1, 1 }, + { ahd_patch1_func, 349, 1, 2 }, + { ahd_patch0_func, 350, 1, 1 }, + { ahd_patch2_func, 358, 1, 2 }, + { ahd_patch0_func, 359, 1, 1 }, + { ahd_patch2_func, 362, 1, 2 }, + { ahd_patch0_func, 363, 1, 1 }, + { ahd_patch1_func, 369, 1, 2 }, + { ahd_patch0_func, 370, 1, 1 }, + { ahd_patch1_func, 372, 1, 2 }, + { ahd_patch0_func, 373, 1, 1 }, + { ahd_patch10_func, 392, 1, 1 }, + { ahd_patch10_func, 395, 1, 1 }, + { ahd_patch10_func, 397, 1, 1 }, + { ahd_patch10_func, 409, 1, 1 }, + { ahd_patch1_func, 419, 1, 2 }, + { ahd_patch0_func, 420, 1, 1 }, + { ahd_patch1_func, 422, 1, 2 }, + { ahd_patch0_func, 423, 1, 1 }, + { ahd_patch1_func, 431, 1, 2 }, + { ahd_patch0_func, 432, 1, 1 }, + { ahd_patch2_func, 445, 1, 2 }, + { ahd_patch0_func, 446, 1, 1 }, + { ahd_patch11_func, 482, 1, 1 }, + { ahd_patch1_func, 490, 1, 2 }, + { ahd_patch0_func, 491, 1, 1 }, + { ahd_patch2_func, 503, 1, 2 }, + { ahd_patch0_func, 504, 1, 1 }, + { ahd_patch12_func, 507, 6, 2 }, + { ahd_patch0_func, 513, 1, 1 }, + { ahd_patch13_func, 534, 7, 1 }, + { ahd_patch14_func, 543, 1, 1 }, + { ahd_patch15_func, 552, 1, 1 }, + { ahd_patch16_func, 553, 1, 2 }, + { ahd_patch0_func, 554, 1, 1 }, + { ahd_patch17_func, 557, 1, 1 }, + { ahd_patch16_func, 558, 1, 1 }, + { ahd_patch18_func, 569, 1, 2 }, + { ahd_patch0_func, 570, 1, 1 }, + { ahd_patch1_func, 589, 1, 2 }, + { ahd_patch0_func, 590, 1, 1 }, + { ahd_patch1_func, 593, 1, 2 }, + { ahd_patch0_func, 594, 1, 1 }, + { ahd_patch2_func, 599, 1, 2 }, + { ahd_patch0_func, 600, 1, 1 }, + { ahd_patch2_func, 604, 1, 2 }, + { ahd_patch0_func, 605, 1, 1 }, + { ahd_patch1_func, 606, 1, 2 }, + { ahd_patch0_func, 607, 1, 1 }, + { ahd_patch2_func, 618, 1, 2 }, + { ahd_patch0_func, 619, 1, 1 }, + { ahd_patch19_func, 623, 1, 1 }, + { ahd_patch20_func, 628, 1, 1 }, + { ahd_patch21_func, 629, 2, 1 }, + { ahd_patch20_func, 633, 1, 2 }, + { ahd_patch0_func, 634, 1, 1 }, + { ahd_patch2_func, 637, 1, 2 }, + { ahd_patch0_func, 638, 1, 1 }, + { ahd_patch2_func, 653, 1, 2 }, + { ahd_patch0_func, 654, 1, 1 }, + { ahd_patch13_func, 655, 14, 1 }, + { ahd_patch1_func, 673, 1, 2 }, + { ahd_patch0_func, 674, 1, 1 }, + { ahd_patch13_func, 675, 1, 1 }, + { ahd_patch1_func, 687, 1, 2 }, + { ahd_patch0_func, 688, 1, 1 }, + { ahd_patch1_func, 695, 1, 2 }, + { ahd_patch0_func, 696, 1, 1 }, + { ahd_patch19_func, 719, 1, 1 }, + { ahd_patch19_func, 757, 1, 1 }, + { ahd_patch1_func, 768, 1, 2 }, + { ahd_patch0_func, 769, 1, 1 }, + { ahd_patch7_func, 785, 3, 1 }, + { ahd_patch1_func, 789, 1, 2 }, + { ahd_patch0_func, 790, 1, 1 }, + { ahd_patch1_func, 792, 1, 2 }, + { ahd_patch0_func, 793, 1, 1 }, + { ahd_patch1_func, 796, 1, 2 }, + { ahd_patch0_func, 797, 1, 1 }, + { ahd_patch22_func, 799, 1, 2 }, + { ahd_patch0_func, 800, 2, 1 }, + { ahd_patch23_func, 803, 4, 2 }, + { ahd_patch0_func, 807, 1, 1 }, + { ahd_patch23_func, 815, 11, 1 } +}; + +static const struct cs { + uint16_t begin; + uint16_t end; +} critical_sections[] = { + { 17, 30 }, + { 47, 58 }, + { 61, 63 }, + { 65, 66 }, + { 72, 92 }, + { 110, 142 }, + { 143, 180 }, + { 185, 193 }, + { 218, 274 }, + { 435, 443 }, + { 453, 455 }, + { 458, 467 }, + { 719, 749 }, + { 759, 763 } +}; + +#define NUM_CRITICAL_SECTIONS ARRAY_SIZE(critical_sections) diff --git a/drivers/scsi/aic7xxx/aic7xxx.h b/drivers/scsi/aic7xxx/aic7xxx.h new file mode 100644 index 000000000..88b90f980 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx.h @@ -0,0 +1,1279 @@ +/* + * Core definitions and data structures shareable across OS platforms. + * + * Copyright (c) 1994-2001 Justin T. Gibbs. + * Copyright (c) 2000-2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aic7xxx.h#85 $ + * + * $FreeBSD$ + */ + +#ifndef _AIC7XXX_H_ +#define _AIC7XXX_H_ + +/* Register Definitions */ +#include "aic7xxx_reg.h" + +/************************* Forward Declarations *******************************/ +struct ahc_platform_data; +struct scb_platform_data; +struct seeprom_descriptor; + +/****************************** Useful Macros *********************************/ +#ifndef TRUE +#define TRUE 1 +#endif +#ifndef FALSE +#define FALSE 0 +#endif + +#define ALL_CHANNELS '\0' +#define ALL_TARGETS_MASK 0xFFFF +#define INITIATOR_WILDCARD (~0) + +#define SCSIID_TARGET(ahc, scsiid) \ + (((scsiid) & ((((ahc)->features & AHC_TWIN) != 0) ? TWIN_TID : TID)) \ + >> TID_SHIFT) +#define SCSIID_OUR_ID(scsiid) \ + ((scsiid) & OID) +#define SCSIID_CHANNEL(ahc, scsiid) \ + ((((ahc)->features & AHC_TWIN) != 0) \ + ? ((((scsiid) & TWIN_CHNLB) != 0) ? 'B' : 'A') \ + : 'A') +#define SCB_IS_SCSIBUS_B(ahc, scb) \ + (SCSIID_CHANNEL(ahc, (scb)->hscb->scsiid) == 'B') +#define SCB_GET_OUR_ID(scb) \ + SCSIID_OUR_ID((scb)->hscb->scsiid) +#define SCB_GET_TARGET(ahc, scb) \ + SCSIID_TARGET((ahc), (scb)->hscb->scsiid) +#define SCB_GET_CHANNEL(ahc, scb) \ + SCSIID_CHANNEL(ahc, (scb)->hscb->scsiid) +#define SCB_GET_LUN(scb) \ + ((scb)->hscb->lun & LID) +#define SCB_GET_TARGET_OFFSET(ahc, scb) \ + (SCB_GET_TARGET(ahc, scb) + (SCB_IS_SCSIBUS_B(ahc, scb) ? 8 : 0)) +#define SCB_GET_TARGET_MASK(ahc, scb) \ + (0x01 << (SCB_GET_TARGET_OFFSET(ahc, scb))) +#ifdef AHC_DEBUG +#define SCB_IS_SILENT(scb) \ + ((ahc_debug & AHC_SHOW_MASKED_ERRORS) == 0 \ + && (((scb)->flags & SCB_SILENT) != 0)) +#else +#define SCB_IS_SILENT(scb) \ + (((scb)->flags & SCB_SILENT) != 0) +#endif +#define TCL_TARGET_OFFSET(tcl) \ + ((((tcl) >> 4) & TID) >> 4) +#define TCL_LUN(tcl) \ + (tcl & (AHC_NUM_LUNS - 1)) +#define BUILD_TCL(scsiid, lun) \ + ((lun) | (((scsiid) & TID) << 4)) + +#ifndef AHC_TARGET_MODE +#undef AHC_TMODE_ENABLE +#define AHC_TMODE_ENABLE 0 +#endif + +/**************************** Driver Constants ********************************/ +/* + * The maximum number of supported targets. + */ +#define AHC_NUM_TARGETS 16 + +/* + * The maximum number of supported luns. + * The identify message only supports 64 luns in SPI3. + * You can have 2^64 luns when information unit transfers are enabled, + * but it is doubtful this driver will ever support IUTs. + */ +#define AHC_NUM_LUNS 64 + +/* + * The maximum transfer per S/G segment. + */ +#define AHC_MAXTRANSFER_SIZE 0x00ffffff /* limited by 24bit counter */ + +/* + * The maximum amount of SCB storage in hardware on a controller. + * This value represents an upper bound. Controllers vary in the number + * they actually support. + */ +#define AHC_SCB_MAX 255 + +/* + * The maximum number of concurrent transactions supported per driver instance. + * Sequencer Control Blocks (SCBs) store per-transaction information. Although + * the space for SCBs on the host adapter varies by model, the driver will + * page the SCBs between host and controller memory as needed. We are limited + * to 253 because: + * 1) The 8bit nature of the RISC engine holds us to an 8bit value. + * 2) We reserve one value, 255, to represent the invalid element. + * 3) Our input queue scheme requires one SCB to always be reserved + * in advance of queuing any SCBs. This takes us down to 254. + * 4) To handle our output queue correctly on machines that only + * support 32bit stores, we must clear the array 4 bytes at a + * time. To avoid colliding with a DMA write from the sequencer, + * we must be sure that 4 slots are empty when we write to clear + * the queue. This reduces us to 253 SCBs: 1 that just completed + * and the known three additional empty slots in the queue that + * precede it. + */ +#define AHC_MAX_QUEUE 253 + +/* + * The maximum amount of SCB storage we allocate in host memory. This + * number should reflect the 1 additional SCB we require to handle our + * qinfifo mechanism. + */ +#define AHC_SCB_MAX_ALLOC (AHC_MAX_QUEUE+1) + +/* + * Ring Buffer of incoming target commands. + * We allocate 256 to simplify the logic in the sequencer + * by using the natural wrap point of an 8bit counter. + */ +#define AHC_TMODE_CMDS 256 + +/* Reset line assertion time in us */ +#define AHC_BUSRESET_DELAY 25 + +/******************* Chip Characteristics/Operating Settings *****************/ +/* + * Chip Type + * The chip order is from least sophisticated to most sophisticated. + */ +typedef enum { + AHC_NONE = 0x0000, + AHC_CHIPID_MASK = 0x00FF, + AHC_AIC7770 = 0x0001, + AHC_AIC7850 = 0x0002, + AHC_AIC7855 = 0x0003, + AHC_AIC7859 = 0x0004, + AHC_AIC7860 = 0x0005, + AHC_AIC7870 = 0x0006, + AHC_AIC7880 = 0x0007, + AHC_AIC7895 = 0x0008, + AHC_AIC7895C = 0x0009, + AHC_AIC7890 = 0x000a, + AHC_AIC7896 = 0x000b, + AHC_AIC7892 = 0x000c, + AHC_AIC7899 = 0x000d, + AHC_VL = 0x0100, /* Bus type VL */ + AHC_EISA = 0x0200, /* Bus type EISA */ + AHC_PCI = 0x0400, /* Bus type PCI */ + AHC_BUS_MASK = 0x0F00 +} ahc_chip; + +/* + * Features available in each chip type. + */ +typedef enum { + AHC_FENONE = 0x00000, + AHC_ULTRA = 0x00001, /* Supports 20MHz Transfers */ + AHC_ULTRA2 = 0x00002, /* Supports 40MHz Transfers */ + AHC_WIDE = 0x00004, /* Wide Channel */ + AHC_TWIN = 0x00008, /* Twin Channel */ + AHC_MORE_SRAM = 0x00010, /* 80 bytes instead of 64 */ + AHC_CMD_CHAN = 0x00020, /* Has a Command DMA Channel */ + AHC_QUEUE_REGS = 0x00040, /* Has Queue management registers */ + AHC_SG_PRELOAD = 0x00080, /* Can perform auto-SG preload */ + AHC_SPIOCAP = 0x00100, /* Has a Serial Port I/O Cap Register */ + AHC_MULTI_TID = 0x00200, /* Has bitmask of TIDs for select-in */ + AHC_HS_MAILBOX = 0x00400, /* Has HS_MAILBOX register */ + AHC_DT = 0x00800, /* Double Transition transfers */ + AHC_NEW_TERMCTL = 0x01000, /* Newer termination scheme */ + AHC_MULTI_FUNC = 0x02000, /* Multi-Function Twin Channel Device */ + AHC_LARGE_SCBS = 0x04000, /* 64byte SCBs */ + AHC_AUTORATE = 0x08000, /* Automatic update of SCSIRATE/OFFSET*/ + AHC_AUTOPAUSE = 0x10000, /* Automatic pause on register access */ + AHC_TARGETMODE = 0x20000, /* Has tested target mode support */ + AHC_MULTIROLE = 0x40000, /* Space for two roles at a time */ + AHC_REMOVABLE = 0x80000, /* Hot-Swap supported */ + AHC_HVD = 0x100000, /* HVD rather than SE */ + AHC_AIC7770_FE = AHC_FENONE, + /* + * The real 7850 does not support Ultra modes, but there are + * several cards that use the generic 7850 PCI ID even though + * they are using an Ultra capable chip (7859/7860). We start + * out with the AHC_ULTRA feature set and then check the DEVSTATUS + * register to determine if the capability is really present. + */ + AHC_AIC7850_FE = AHC_SPIOCAP|AHC_AUTOPAUSE|AHC_TARGETMODE|AHC_ULTRA, + AHC_AIC7860_FE = AHC_AIC7850_FE, + AHC_AIC7870_FE = AHC_TARGETMODE|AHC_AUTOPAUSE, + AHC_AIC7880_FE = AHC_AIC7870_FE|AHC_ULTRA, + /* + * Although we have space for both the initiator and + * target roles on ULTRA2 chips, we currently disable + * the initiator role to allow multi-scsi-id target mode + * configurations. We can only respond on the same SCSI + * ID as our initiator role if we allow initiator operation. + * At some point, we should add a configuration knob to + * allow both roles to be loaded. + */ + AHC_AIC7890_FE = AHC_MORE_SRAM|AHC_CMD_CHAN|AHC_ULTRA2 + |AHC_QUEUE_REGS|AHC_SG_PRELOAD|AHC_MULTI_TID + |AHC_HS_MAILBOX|AHC_NEW_TERMCTL|AHC_LARGE_SCBS + |AHC_TARGETMODE, + AHC_AIC7892_FE = AHC_AIC7890_FE|AHC_DT|AHC_AUTORATE|AHC_AUTOPAUSE, + AHC_AIC7895_FE = AHC_AIC7880_FE|AHC_MORE_SRAM|AHC_AUTOPAUSE + |AHC_CMD_CHAN|AHC_MULTI_FUNC|AHC_LARGE_SCBS, + AHC_AIC7895C_FE = AHC_AIC7895_FE|AHC_MULTI_TID, + AHC_AIC7896_FE = AHC_AIC7890_FE|AHC_MULTI_FUNC, + AHC_AIC7899_FE = AHC_AIC7892_FE|AHC_MULTI_FUNC +} ahc_feature; + +/* + * Bugs in the silicon that we work around in software. + */ +typedef enum { + AHC_BUGNONE = 0x00, + /* + * On all chips prior to the U2 product line, + * the WIDEODD S/G segment feature does not + * work during scsi->HostBus transfers. + */ + AHC_TMODE_WIDEODD_BUG = 0x01, + /* + * On the aic7890/91 Rev 0 chips, the autoflush + * feature does not work. A manual flush of + * the DMA FIFO is required. + */ + AHC_AUTOFLUSH_BUG = 0x02, + /* + * On many chips, cacheline streaming does not work. + */ + AHC_CACHETHEN_BUG = 0x04, + /* + * On the aic7896/97 chips, cacheline + * streaming must be enabled. + */ + AHC_CACHETHEN_DIS_BUG = 0x08, + /* + * PCI 2.1 Retry failure on non-empty data fifo. + */ + AHC_PCI_2_1_RETRY_BUG = 0x10, + /* + * Controller does not handle cacheline residuals + * properly on S/G segments if PCI MWI instructions + * are allowed. + */ + AHC_PCI_MWI_BUG = 0x20, + /* + * An SCB upload using the SCB channel's + * auto array entry copy feature may + * corrupt data. This appears to only + * occur on 66MHz systems. + */ + AHC_SCBCHAN_UPLOAD_BUG = 0x40 +} ahc_bug; + +/* + * Configuration specific settings. + * The driver determines these settings by probing the + * chip/controller's configuration. + */ +typedef enum { + AHC_FNONE = 0x000, + AHC_PRIMARY_CHANNEL = 0x003, /* + * The channel that should + * be probed first. + */ + AHC_USEDEFAULTS = 0x004, /* + * For cards without an seeprom + * or a BIOS to initialize the chip's + * SRAM, we use the default target + * settings. + */ + AHC_SEQUENCER_DEBUG = 0x008, + AHC_SHARED_SRAM = 0x010, + AHC_LARGE_SEEPROM = 0x020, /* Uses C56_66 not C46 */ + AHC_RESET_BUS_A = 0x040, + AHC_RESET_BUS_B = 0x080, + AHC_EXTENDED_TRANS_A = 0x100, + AHC_EXTENDED_TRANS_B = 0x200, + AHC_TERM_ENB_A = 0x400, + AHC_TERM_ENB_B = 0x800, + AHC_INITIATORROLE = 0x1000, /* + * Allow initiator operations on + * this controller. + */ + AHC_TARGETROLE = 0x2000, /* + * Allow target operations on this + * controller. + */ + AHC_NEWEEPROM_FMT = 0x4000, + AHC_TQINFIFO_BLOCKED = 0x10000, /* Blocked waiting for ATIOs */ + AHC_INT50_SPEEDFLEX = 0x20000, /* + * Internal 50pin connector + * sits behind an aic3860 + */ + AHC_SCB_BTT = 0x40000, /* + * The busy targets table is + * stored in SCB space rather + * than SRAM. + */ + AHC_BIOS_ENABLED = 0x80000, + AHC_ALL_INTERRUPTS = 0x100000, + AHC_PAGESCBS = 0x400000, /* Enable SCB paging */ + AHC_EDGE_INTERRUPT = 0x800000, /* Device uses edge triggered ints */ + AHC_39BIT_ADDRESSING = 0x1000000, /* Use 39 bit addressing scheme. */ + AHC_LSCBS_ENABLED = 0x2000000, /* 64Byte SCBs enabled */ + AHC_SCB_CONFIG_USED = 0x4000000, /* No SEEPROM but SCB2 had info. */ + AHC_NO_BIOS_INIT = 0x8000000, /* No BIOS left over settings. */ + AHC_DISABLE_PCI_PERR = 0x10000000, + AHC_HAS_TERM_LOGIC = 0x20000000 +} ahc_flag; + +/************************* Hardware SCB Definition ***************************/ + +/* + * The driver keeps up to MAX_SCB scb structures per card in memory. The SCB + * consists of a "hardware SCB" mirroring the fields available on the card + * and additional information the kernel stores for each transaction. + * + * To minimize space utilization, a portion of the hardware scb stores + * different data during different portions of a SCSI transaction. + * As initialized by the host driver for the initiator role, this area + * contains the SCSI cdb (or a pointer to the cdb) to be executed. After + * the cdb has been presented to the target, this area serves to store + * residual transfer information and the SCSI status byte. + * For the target role, the contents of this area do not change, but + * still serve a different purpose than for the initiator role. See + * struct target_data for details. + */ + +/* + * Status information embedded in the shared poriton of + * an SCB after passing the cdb to the target. The kernel + * driver will only read this data for transactions that + * complete abnormally (non-zero status byte). + */ +struct status_pkt { + uint32_t residual_datacnt; /* Residual in the current S/G seg */ + uint32_t residual_sg_ptr; /* The next S/G for this transfer */ + uint8_t scsi_status; /* Standard SCSI status byte */ +}; + +/* + * Target mode version of the shared data SCB segment. + */ +struct target_data { + uint32_t residual_datacnt; /* Residual in the current S/G seg */ + uint32_t residual_sg_ptr; /* The next S/G for this transfer */ + uint8_t scsi_status; /* SCSI status to give to initiator */ + uint8_t target_phases; /* Bitmap of phases to execute */ + uint8_t data_phase; /* Data-In or Data-Out */ + uint8_t initiator_tag; /* Initiator's transaction tag */ +}; + +struct hardware_scb { +/*0*/ union { + /* + * If the cdb is 12 bytes or less, we embed it directly + * in the SCB. For longer cdbs, we embed the address + * of the cdb payload as seen by the chip and a DMA + * is used to pull it in. + */ + uint8_t cdb[12]; + uint32_t cdb_ptr; + struct status_pkt status; + struct target_data tdata; + } shared_data; +/* + * A word about residuals. + * The scb is presented to the sequencer with the dataptr and datacnt + * fields initialized to the contents of the first S/G element to + * transfer. The sgptr field is initialized to the bus address for + * the S/G element that follows the first in the in core S/G array + * or'ed with the SG_FULL_RESID flag. Sgptr may point to an invalid + * S/G entry for this transfer (single S/G element transfer with the + * first elements address and length preloaded in the dataptr/datacnt + * fields). If no transfer is to occur, sgptr is set to SG_LIST_NULL. + * The SG_FULL_RESID flag ensures that the residual will be correctly + * noted even if no data transfers occur. Once the data phase is entered, + * the residual sgptr and datacnt are loaded from the sgptr and the + * datacnt fields. After each S/G element's dataptr and length are + * loaded into the hardware, the residual sgptr is advanced. After + * each S/G element is expired, its datacnt field is checked to see + * if the LAST_SEG flag is set. If so, SG_LIST_NULL is set in the + * residual sg ptr and the transfer is considered complete. If the + * sequencer determines that there is a residual in the tranfer, it + * will set the SG_RESID_VALID flag in sgptr and dma the scb back into + * host memory. To sumarize: + * + * Sequencer: + * o A residual has occurred if SG_FULL_RESID is set in sgptr, + * or residual_sgptr does not have SG_LIST_NULL set. + * + * o We are transferring the last segment if residual_datacnt has + * the SG_LAST_SEG flag set. + * + * Host: + * o A residual has occurred if a completed scb has the + * SG_RESID_VALID flag set. + * + * o residual_sgptr and sgptr refer to the "next" sg entry + * and so may point beyond the last valid sg entry for the + * transfer. + */ +/*12*/ uint32_t dataptr; +/*16*/ uint32_t datacnt; /* + * Byte 3 (numbered from 0) of + * the datacnt is really the + * 4th byte in that data address. + */ +/*20*/ uint32_t sgptr; +#define SG_PTR_MASK 0xFFFFFFF8 +/*24*/ uint8_t control; /* See SCB_CONTROL in aic7xxx.reg for details */ +/*25*/ uint8_t scsiid; /* what to load in the SCSIID register */ +/*26*/ uint8_t lun; +/*27*/ uint8_t tag; /* + * Index into our kernel SCB array. + * Also used as the tag for tagged I/O + */ +/*28*/ uint8_t cdb_len; +/*29*/ uint8_t scsirate; /* Value for SCSIRATE register */ +/*30*/ uint8_t scsioffset; /* Value for SCSIOFFSET register */ +/*31*/ uint8_t next; /* + * Used for threading SCBs in the + * "Waiting for Selection" and + * "Disconnected SCB" lists down + * in the sequencer. + */ +/*32*/ uint8_t cdb32[32]; /* + * CDB storage for cdbs of size + * 13->32. We store them here + * because hardware scbs are + * allocated from DMA safe + * memory so we are guaranteed + * the controller can access + * this data. + */ +}; + +/************************ Kernel SCB Definitions ******************************/ +/* + * Some fields of the SCB are OS dependent. Here we collect the + * definitions for elements that all OS platforms need to include + * in there SCB definition. + */ + +/* + * Definition of a scatter/gather element as transferred to the controller. + * The aic7xxx chips only support a 24bit length. We use the top byte of + * the length to store additional address bits and a flag to indicate + * that a given segment terminates the transfer. This gives us an + * addressable range of 512GB on machines with 64bit PCI or with chips + * that can support dual address cycles on 32bit PCI busses. + */ +struct ahc_dma_seg { + uint32_t addr; + uint32_t len; +#define AHC_DMA_LAST_SEG 0x80000000 +#define AHC_SG_HIGH_ADDR_MASK 0x7F000000 +#define AHC_SG_LEN_MASK 0x00FFFFFF +}; + +struct sg_map_node { + bus_dmamap_t sg_dmamap; + dma_addr_t sg_physaddr; + struct ahc_dma_seg* sg_vaddr; + SLIST_ENTRY(sg_map_node) links; +}; + +/* + * The current state of this SCB. + */ +typedef enum { + SCB_FREE = 0x0000, + SCB_OTHERTCL_TIMEOUT = 0x0002,/* + * Another device was active + * during the first timeout for + * this SCB so we gave ourselves + * an additional timeout period + * in case it was hogging the + * bus. + */ + SCB_DEVICE_RESET = 0x0004, + SCB_SENSE = 0x0008, + SCB_CDB32_PTR = 0x0010, + SCB_RECOVERY_SCB = 0x0020, + SCB_AUTO_NEGOTIATE = 0x0040,/* Negotiate to achieve goal. */ + SCB_NEGOTIATE = 0x0080,/* Negotiation forced for command. */ + SCB_ABORT = 0x0100, + SCB_UNTAGGEDQ = 0x0200, + SCB_ACTIVE = 0x0400, + SCB_TARGET_IMMEDIATE = 0x0800, + SCB_TRANSMISSION_ERROR = 0x1000,/* + * We detected a parity or CRC + * error that has effected the + * payload of the command. This + * flag is checked when normal + * status is returned to catch + * the case of a target not + * responding to our attempt + * to report the error. + */ + SCB_TARGET_SCB = 0x2000, + SCB_SILENT = 0x4000 /* + * Be quiet about transmission type + * errors. They are expected and we + * don't want to upset the user. This + * flag is typically used during DV. + */ +} scb_flag; + +struct scb { + struct hardware_scb *hscb; + union { + SLIST_ENTRY(scb) sle; + TAILQ_ENTRY(scb) tqe; + } links; + LIST_ENTRY(scb) pending_links; + ahc_io_ctx_t io_ctx; + struct ahc_softc *ahc_softc; + scb_flag flags; + struct scb_platform_data *platform_data; + struct sg_map_node *sg_map; + struct ahc_dma_seg *sg_list; + dma_addr_t sg_list_phys; + u_int sg_count;/* How full ahc_dma_seg is */ +}; + +struct scb_data { + SLIST_HEAD(, scb) free_scbs; /* + * Pool of SCBs ready to be assigned + * commands to execute. + */ + struct scb *scbindex[256]; /* + * Mapping from tag to SCB. + * As tag identifiers are an + * 8bit value, we provide space + * for all possible tag values. + * Any lookups to entries at or + * above AHC_SCB_MAX_ALLOC will + * always fail. + */ + struct hardware_scb *hscbs; /* Array of hardware SCBs */ + struct scb *scbarray; /* Array of kernel SCBs */ + struct scsi_sense_data *sense; /* Per SCB sense data */ + + /* + * "Bus" addresses of our data structures. + */ + bus_dma_tag_t hscb_dmat; /* dmat for our hardware SCB array */ + bus_dmamap_t hscb_dmamap; + dma_addr_t hscb_busaddr; + bus_dma_tag_t sense_dmat; + bus_dmamap_t sense_dmamap; + dma_addr_t sense_busaddr; + bus_dma_tag_t sg_dmat; /* dmat for our sg segments */ + SLIST_HEAD(, sg_map_node) sg_maps; + uint8_t numscbs; + uint8_t maxhscbs; /* Number of SCBs on the card */ + uint8_t init_level; /* + * How far we've initialized + * this structure. + */ +}; + +/************************ Target Mode Definitions *****************************/ + +/* + * Connection descriptor for select-in requests in target mode. + */ +struct target_cmd { + uint8_t scsiid; /* Our ID and the initiator's ID */ + uint8_t identify; /* Identify message */ + uint8_t bytes[22]; /* + * Bytes contains any additional message + * bytes terminated by 0xFF. The remainder + * is the cdb to execute. + */ + uint8_t cmd_valid; /* + * When a command is complete, the firmware + * will set cmd_valid to all bits set. + * After the host has seen the command, + * the bits are cleared. This allows us + * to just peek at host memory to determine + * if more work is complete. cmd_valid is on + * an 8 byte boundary to simplify setting + * it on aic7880 hardware which only has + * limited direct access to the DMA FIFO. + */ + uint8_t pad[7]; +}; + +/* + * Number of events we can buffer up if we run out + * of immediate notify ccbs. + */ +#define AHC_TMODE_EVENT_BUFFER_SIZE 8 +struct ahc_tmode_event { + uint8_t initiator_id; + uint8_t event_type; /* MSG type or EVENT_TYPE_BUS_RESET */ +#define EVENT_TYPE_BUS_RESET 0xFF + uint8_t event_arg; +}; + +/* + * Per enabled lun target mode state. + * As this state is directly influenced by the host OS'es target mode + * environment, we let the OS module define it. Forward declare the + * structure here so we can store arrays of them, etc. in OS neutral + * data structures. + */ +#ifdef AHC_TARGET_MODE +struct ahc_tmode_lstate { + struct cam_path *path; + struct ccb_hdr_slist accept_tios; + struct ccb_hdr_slist immed_notifies; + struct ahc_tmode_event event_buffer[AHC_TMODE_EVENT_BUFFER_SIZE]; + uint8_t event_r_idx; + uint8_t event_w_idx; +}; +#else +struct ahc_tmode_lstate; +#endif + +/******************** Transfer Negotiation Datastructures *********************/ +#define AHC_TRANS_CUR 0x01 /* Modify current neogtiation status */ +#define AHC_TRANS_ACTIVE 0x03 /* Assume this target is on the bus */ +#define AHC_TRANS_GOAL 0x04 /* Modify negotiation goal */ +#define AHC_TRANS_USER 0x08 /* Modify user negotiation settings */ + +#define AHC_WIDTH_UNKNOWN 0xFF +#define AHC_PERIOD_UNKNOWN 0xFF +#define AHC_OFFSET_UNKNOWN 0xFF +#define AHC_PPR_OPTS_UNKNOWN 0xFF + +/* + * Transfer Negotiation Information. + */ +struct ahc_transinfo { + uint8_t protocol_version; /* SCSI Revision level */ + uint8_t transport_version; /* SPI Revision level */ + uint8_t width; /* Bus width */ + uint8_t period; /* Sync rate factor */ + uint8_t offset; /* Sync offset */ + uint8_t ppr_options; /* Parallel Protocol Request options */ +}; + +/* + * Per-initiator current, goal and user transfer negotiation information. */ +struct ahc_initiator_tinfo { + uint8_t scsirate; /* Computed value for SCSIRATE reg */ + struct ahc_transinfo curr; + struct ahc_transinfo goal; + struct ahc_transinfo user; +}; + +/* + * Per enabled target ID state. + * Pointers to lun target state as well as sync/wide negotiation information + * for each initiator<->target mapping. For the initiator role we pretend + * that we are the target and the targets are the initiators since the + * negotiation is the same regardless of role. + */ +struct ahc_tmode_tstate { + struct ahc_tmode_lstate* enabled_luns[AHC_NUM_LUNS]; + struct ahc_initiator_tinfo transinfo[AHC_NUM_TARGETS]; + + /* + * Per initiator state bitmasks. + */ + uint16_t auto_negotiate;/* Auto Negotiation Required */ + uint16_t ultraenb; /* Using ultra sync rate */ + uint16_t discenable; /* Disconnection allowed */ + uint16_t tagenable; /* Tagged Queuing allowed */ +}; + +/* + * Data structure for our table of allowed synchronous transfer rates. + */ +struct ahc_syncrate { + u_int sxfr_u2; /* Value of the SXFR parameter for Ultra2+ Chips */ + u_int sxfr; /* Value of the SXFR parameter for <= Ultra Chips */ +#define ULTRA_SXFR 0x100 /* Rate Requires Ultra Mode set */ +#define ST_SXFR 0x010 /* Rate Single Transition Only */ +#define DT_SXFR 0x040 /* Rate Double Transition Only */ + uint8_t period; /* Period to send to SCSI target */ + const char *rate; +}; + +/* Safe and valid period for async negotiations. */ +#define AHC_ASYNC_XFER_PERIOD 0x45 +#define AHC_ULTRA2_XFER_PERIOD 0x0a + +/* + * Indexes into our table of syncronous transfer rates. + */ +#define AHC_SYNCRATE_DT 0 +#define AHC_SYNCRATE_ULTRA2 1 +#define AHC_SYNCRATE_ULTRA 3 +#define AHC_SYNCRATE_FAST 6 +#define AHC_SYNCRATE_MAX AHC_SYNCRATE_DT +#define AHC_SYNCRATE_MIN 13 + +/***************************** Lookup Tables **********************************/ +/* + * Phase -> name and message out response + * to parity errors in each phase table. + */ +struct ahc_phase_table_entry { + uint8_t phase; + uint8_t mesg_out; /* Message response to parity errors */ + char *phasemsg; +}; + +/************************** Serial EEPROM Format ******************************/ + +struct seeprom_config { +/* + * Per SCSI ID Configuration Flags + */ + uint16_t device_flags[16]; /* words 0-15 */ +#define CFXFER 0x0007 /* synchronous transfer rate */ +#define CFSYNCH 0x0008 /* enable synchronous transfer */ +#define CFDISC 0x0010 /* enable disconnection */ +#define CFWIDEB 0x0020 /* wide bus device */ +#define CFSYNCHISULTRA 0x0040 /* CFSYNCH is an ultra offset (2940AU)*/ +#define CFSYNCSINGLE 0x0080 /* Single-Transition signalling */ +#define CFSTART 0x0100 /* send start unit SCSI command */ +#define CFINCBIOS 0x0200 /* include in BIOS scan */ +#define CFRNFOUND 0x0400 /* report even if not found */ +#define CFMULTILUNDEV 0x0800 /* Probe multiple luns in BIOS scan */ +#define CFWBCACHEENB 0x4000 /* Enable W-Behind Cache on disks */ +#define CFWBCACHENOP 0xc000 /* Don't touch W-Behind Cache */ + +/* + * BIOS Control Bits + */ + uint16_t bios_control; /* word 16 */ +#define CFSUPREM 0x0001 /* support all removeable drives */ +#define CFSUPREMB 0x0002 /* support removeable boot drives */ +#define CFBIOSEN 0x0004 /* BIOS enabled */ +#define CFBIOS_BUSSCAN 0x0008 /* Have the BIOS Scan the Bus */ +#define CFSM2DRV 0x0010 /* support more than two drives */ +#define CFSTPWLEVEL 0x0010 /* Termination level control */ +#define CF284XEXTEND 0x0020 /* extended translation (284x cards) */ +#define CFCTRL_A 0x0020 /* BIOS displays Ctrl-A message */ +#define CFTERM_MENU 0x0040 /* BIOS displays termination menu */ +#define CFEXTEND 0x0080 /* extended translation enabled */ +#define CFSCAMEN 0x0100 /* SCAM enable */ +#define CFMSG_LEVEL 0x0600 /* BIOS Message Level */ +#define CFMSG_VERBOSE 0x0000 +#define CFMSG_SILENT 0x0200 +#define CFMSG_DIAG 0x0400 +#define CFBOOTCD 0x0800 /* Support Bootable CD-ROM */ +/* UNUSED 0xff00 */ + +/* + * Host Adapter Control Bits + */ + uint16_t adapter_control; /* word 17 */ +#define CFAUTOTERM 0x0001 /* Perform Auto termination */ +#define CFULTRAEN 0x0002 /* Ultra SCSI speed enable */ +#define CF284XSELTO 0x0003 /* Selection timeout (284x cards) */ +#define CF284XFIFO 0x000C /* FIFO Threshold (284x cards) */ +#define CFSTERM 0x0004 /* SCSI low byte termination */ +#define CFWSTERM 0x0008 /* SCSI high byte termination */ +#define CFSPARITY 0x0010 /* SCSI parity */ +#define CF284XSTERM 0x0020 /* SCSI low byte term (284x cards) */ +#define CFMULTILUN 0x0020 +#define CFRESETB 0x0040 /* reset SCSI bus at boot */ +#define CFCLUSTERENB 0x0080 /* Cluster Enable */ +#define CFBOOTCHAN 0x0300 /* probe this channel first */ +#define CFBOOTCHANSHIFT 8 +#define CFSEAUTOTERM 0x0400 /* Ultra2 Perform secondary Auto Term*/ +#define CFSELOWTERM 0x0800 /* Ultra2 secondary low term */ +#define CFSEHIGHTERM 0x1000 /* Ultra2 secondary high term */ +#define CFENABLEDV 0x4000 /* Perform Domain Validation*/ + +/* + * Bus Release Time, Host Adapter ID + */ + uint16_t brtime_id; /* word 18 */ +#define CFSCSIID 0x000f /* host adapter SCSI ID */ +/* UNUSED 0x00f0 */ +#define CFBRTIME 0xff00 /* bus release time */ + +/* + * Maximum targets + */ + uint16_t max_targets; /* word 19 */ +#define CFMAXTARG 0x00ff /* maximum targets */ +#define CFBOOTLUN 0x0f00 /* Lun to boot from */ +#define CFBOOTID 0xf000 /* Target to boot from */ + uint16_t res_1[10]; /* words 20-29 */ + uint16_t signature; /* Signature == 0x250 */ +#define CFSIGNATURE 0x250 +#define CFSIGNATURE2 0x300 + uint16_t checksum; /* word 31 */ +}; + +/**************************** Message Buffer *********************************/ +typedef enum { + MSG_TYPE_NONE = 0x00, + MSG_TYPE_INITIATOR_MSGOUT = 0x01, + MSG_TYPE_INITIATOR_MSGIN = 0x02, + MSG_TYPE_TARGET_MSGOUT = 0x03, + MSG_TYPE_TARGET_MSGIN = 0x04 +} ahc_msg_type; + +typedef enum { + MSGLOOP_IN_PROG, + MSGLOOP_MSGCOMPLETE, + MSGLOOP_TERMINATED +} msg_loop_stat; + +/*********************** Software Configuration Structure *********************/ +TAILQ_HEAD(scb_tailq, scb); + +struct ahc_aic7770_softc { + /* + * Saved register state used for chip_init(). + */ + uint8_t busspd; + uint8_t bustime; +}; + +struct ahc_pci_softc { + /* + * Saved register state used for chip_init(). + */ + uint32_t devconfig; + uint16_t targcrccnt; + uint8_t command; + uint8_t csize_lattime; + uint8_t optionmode; + uint8_t crccontrol1; + uint8_t dscommand0; + uint8_t dspcistatus; + uint8_t scbbaddr; + uint8_t dff_thrsh; +}; + +union ahc_bus_softc { + struct ahc_aic7770_softc aic7770_softc; + struct ahc_pci_softc pci_softc; +}; + +typedef void (*ahc_bus_intr_t)(struct ahc_softc *); +typedef int (*ahc_bus_chip_init_t)(struct ahc_softc *); +typedef int (*ahc_bus_suspend_t)(struct ahc_softc *); +typedef int (*ahc_bus_resume_t)(struct ahc_softc *); +typedef void ahc_callback_t (void *); + +struct ahc_softc { + bus_space_tag_t tag; + bus_space_handle_t bsh; + struct scb_data *scb_data; + + struct scb *next_queued_scb; + + /* + * SCBs that have been sent to the controller + */ + BSD_LIST_HEAD(, scb) pending_scbs; + + /* + * Counting lock for deferring the release of additional + * untagged transactions from the untagged_queues. When + * the lock is decremented to 0, all queues in the + * untagged_queues array are run. + */ + u_int untagged_queue_lock; + + /* + * Per-target queue of untagged-transactions. The + * transaction at the head of the queue is the + * currently pending untagged transaction for the + * target. The driver only allows a single untagged + * transaction per target. + */ + struct scb_tailq untagged_queues[AHC_NUM_TARGETS]; + + /* + * Bus attachment specific data. + */ + union ahc_bus_softc bus_softc; + + /* + * Platform specific data. + */ + struct ahc_platform_data *platform_data; + + /* + * Platform specific device information. + */ + ahc_dev_softc_t dev_softc; + struct device *dev; + + /* + * Bus specific device information. + */ + ahc_bus_intr_t bus_intr; + + /* + * Bus specific initialization required + * after a chip reset. + */ + ahc_bus_chip_init_t bus_chip_init; + + /* + * Target mode related state kept on a per enabled lun basis. + * Targets that are not enabled will have null entries. + * As an initiator, we keep one target entry for our initiator + * ID to store our sync/wide transfer settings. + */ + struct ahc_tmode_tstate *enabled_targets[AHC_NUM_TARGETS]; + + /* + * The black hole device responsible for handling requests for + * disabled luns on enabled targets. + */ + struct ahc_tmode_lstate *black_hole; + + /* + * Device instance currently on the bus awaiting a continue TIO + * for a command that was not given the disconnect priveledge. + */ + struct ahc_tmode_lstate *pending_device; + + /* + * Card characteristics + */ + ahc_chip chip; + ahc_feature features; + ahc_bug bugs; + ahc_flag flags; + struct seeprom_config *seep_config; + + /* Values to store in the SEQCTL register for pause and unpause */ + uint8_t unpause; + uint8_t pause; + + /* Command Queues */ + uint8_t qoutfifonext; + uint8_t qinfifonext; + uint8_t *qoutfifo; + uint8_t *qinfifo; + + /* Critical Section Data */ + struct cs *critical_sections; + u_int num_critical_sections; + + /* Channel Names ('A', 'B', etc.) */ + char channel; + char channel_b; + + /* Initiator Bus ID */ + uint8_t our_id; + uint8_t our_id_b; + + /* + * PCI error detection. + */ + int unsolicited_ints; + + /* + * Target incoming command FIFO. + */ + struct target_cmd *targetcmds; + uint8_t tqinfifonext; + + /* + * Cached copy of the sequencer control register. + */ + uint8_t seqctl; + + /* + * Incoming and outgoing message handling. + */ + uint8_t send_msg_perror; + ahc_msg_type msg_type; + uint8_t msgout_buf[12];/* Message we are sending */ + uint8_t msgin_buf[12];/* Message we are receiving */ + u_int msgout_len; /* Length of message to send */ + u_int msgout_index; /* Current index in msgout */ + u_int msgin_index; /* Current index in msgin */ + + /* + * Mapping information for data structures shared + * between the sequencer and kernel. + */ + bus_dma_tag_t parent_dmat; + bus_dma_tag_t shared_data_dmat; + bus_dmamap_t shared_data_dmamap; + dma_addr_t shared_data_busaddr; + + /* + * Bus address of the one byte buffer used to + * work-around a DMA bug for chips <= aic7880 + * in target mode. + */ + dma_addr_t dma_bug_buf; + + /* Number of enabled target mode device on this card */ + u_int enabled_luns; + + /* Initialization level of this data structure */ + u_int init_level; + + /* PCI cacheline size. */ + u_int pci_cachesize; + + /* + * Count of parity errors we have seen as a target. + * We auto-disable parity error checking after seeing + * AHC_PCI_TARGET_PERR_THRESH number of errors. + */ + u_int pci_target_perr_count; +#define AHC_PCI_TARGET_PERR_THRESH 10 + + /* Maximum number of sequencer instructions supported. */ + u_int instruction_ram_size; + + /* Per-Unit descriptive information */ + const char *description; + char *name; + int unit; + + /* Selection Timer settings */ + int seltime; + int seltime_b; + + uint16_t user_discenable;/* Disconnection allowed */ + uint16_t user_tagenable;/* Tagged Queuing allowed */ +}; + +/************************ Active Device Information ***************************/ +typedef enum { + ROLE_UNKNOWN, + ROLE_INITIATOR, + ROLE_TARGET +} role_t; + +struct ahc_devinfo { + int our_scsiid; + int target_offset; + uint16_t target_mask; + u_int target; + u_int lun; + char channel; + role_t role; /* + * Only guaranteed to be correct if not + * in the busfree state. + */ +}; + +/****************************** PCI Structures ********************************/ +typedef int (ahc_device_setup_t)(struct ahc_softc *); + +struct ahc_pci_identity { + uint64_t full_id; + uint64_t id_mask; + const char *name; + ahc_device_setup_t *setup; +}; + +/***************************** VL/EISA Declarations ***************************/ +struct aic7770_identity { + uint32_t full_id; + uint32_t id_mask; + const char *name; + ahc_device_setup_t *setup; +}; +extern struct aic7770_identity aic7770_ident_table[]; +extern const int ahc_num_aic7770_devs; + +#define AHC_EISA_SLOT_OFFSET 0xc00 +#define AHC_EISA_IOSIZE 0x100 + +/*************************** Function Declarations ****************************/ +/******************************************************************************/ + +/***************************** PCI Front End *********************************/ +const struct ahc_pci_identity *ahc_find_pci_device(ahc_dev_softc_t); +int ahc_pci_config(struct ahc_softc *, + const struct ahc_pci_identity *); +int ahc_pci_test_register_access(struct ahc_softc *); +#ifdef CONFIG_PM +void ahc_pci_resume(struct ahc_softc *ahc); +#endif + +/*************************** EISA/VL Front End ********************************/ +struct aic7770_identity *aic7770_find_device(uint32_t); +int aic7770_config(struct ahc_softc *ahc, + struct aic7770_identity *, + u_int port); + +/************************** SCB and SCB queue management **********************/ +int ahc_probe_scbs(struct ahc_softc *); +void ahc_qinfifo_requeue_tail(struct ahc_softc *ahc, + struct scb *scb); +int ahc_match_scb(struct ahc_softc *ahc, struct scb *scb, + int target, char channel, int lun, + u_int tag, role_t role); + +/****************************** Initialization ********************************/ +struct ahc_softc *ahc_alloc(void *platform_arg, char *name); +int ahc_softc_init(struct ahc_softc *); +void ahc_controller_info(struct ahc_softc *ahc, char *buf); +int ahc_chip_init(struct ahc_softc *ahc); +int ahc_init(struct ahc_softc *ahc); +void ahc_intr_enable(struct ahc_softc *ahc, int enable); +void ahc_pause_and_flushwork(struct ahc_softc *ahc); +#ifdef CONFIG_PM +int ahc_suspend(struct ahc_softc *ahc); +int ahc_resume(struct ahc_softc *ahc); +#endif +void ahc_set_unit(struct ahc_softc *, int); +void ahc_set_name(struct ahc_softc *, char *); +void ahc_free(struct ahc_softc *ahc); +int ahc_reset(struct ahc_softc *ahc, int reinit); + +/***************************** Error Recovery *********************************/ +typedef enum { + SEARCH_COMPLETE, + SEARCH_COUNT, + SEARCH_REMOVE +} ahc_search_action; +int ahc_search_qinfifo(struct ahc_softc *ahc, int target, + char channel, int lun, u_int tag, + role_t role, uint32_t status, + ahc_search_action action); +int ahc_search_untagged_queues(struct ahc_softc *ahc, + ahc_io_ctx_t ctx, + int target, char channel, + int lun, uint32_t status, + ahc_search_action action); +int ahc_search_disc_list(struct ahc_softc *ahc, int target, + char channel, int lun, u_int tag, + int stop_on_first, int remove, + int save_state); +int ahc_reset_channel(struct ahc_softc *ahc, char channel, + int initiate_reset); + +/*************************** Utility Functions ********************************/ +void ahc_compile_devinfo(struct ahc_devinfo *devinfo, + u_int our_id, u_int target, + u_int lun, char channel, + role_t role); +/************************** Transfer Negotiation ******************************/ +const struct ahc_syncrate* ahc_find_syncrate(struct ahc_softc *ahc, u_int *period, + u_int *ppr_options, u_int maxsync); +u_int ahc_find_period(struct ahc_softc *ahc, + u_int scsirate, u_int maxsync); +/* + * Negotiation types. These are used to qualify if we should renegotiate + * even if our goal and current transport parameters are identical. + */ +typedef enum { + AHC_NEG_TO_GOAL, /* Renegotiate only if goal and curr differ. */ + AHC_NEG_IF_NON_ASYNC, /* Renegotiate so long as goal is non-async. */ + AHC_NEG_ALWAYS /* Renegotiat even if goal is async. */ +} ahc_neg_type; +int ahc_update_neg_request(struct ahc_softc*, + struct ahc_devinfo*, + struct ahc_tmode_tstate*, + struct ahc_initiator_tinfo*, + ahc_neg_type); +void ahc_set_width(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo, + u_int width, u_int type, int paused); +void ahc_set_syncrate(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo, + const struct ahc_syncrate *syncrate, + u_int period, u_int offset, + u_int ppr_options, + u_int type, int paused); +typedef enum { + AHC_QUEUE_NONE, + AHC_QUEUE_BASIC, + AHC_QUEUE_TAGGED +} ahc_queue_alg; + +/**************************** Target Mode *************************************/ +#ifdef AHC_TARGET_MODE +void ahc_send_lstate_events(struct ahc_softc *, + struct ahc_tmode_lstate *); +void ahc_handle_en_lun(struct ahc_softc *ahc, + struct cam_sim *sim, union ccb *ccb); +cam_status ahc_find_tmode_devs(struct ahc_softc *ahc, + struct cam_sim *sim, union ccb *ccb, + struct ahc_tmode_tstate **tstate, + struct ahc_tmode_lstate **lstate, + int notfound_failure); +#ifndef AHC_TMODE_ENABLE +#define AHC_TMODE_ENABLE 0 +#endif +#endif +/******************************* Debug ***************************************/ +#ifdef AHC_DEBUG +extern uint32_t ahc_debug; +#define AHC_SHOW_MISC 0x0001 +#define AHC_SHOW_SENSE 0x0002 +#define AHC_DUMP_SEEPROM 0x0004 +#define AHC_SHOW_TERMCTL 0x0008 +#define AHC_SHOW_MEMORY 0x0010 +#define AHC_SHOW_MESSAGES 0x0020 +#define AHC_SHOW_DV 0x0040 +#define AHC_SHOW_SELTO 0x0080 +#define AHC_SHOW_QFULL 0x0200 +#define AHC_SHOW_QUEUE 0x0400 +#define AHC_SHOW_TQIN 0x0800 +#define AHC_SHOW_MASKED_ERRORS 0x1000 +#define AHC_DEBUG_SEQUENCER 0x2000 +#endif +void ahc_print_devinfo(struct ahc_softc *ahc, + struct ahc_devinfo *dev); +void ahc_dump_card_state(struct ahc_softc *ahc); +int ahc_print_register(const ahc_reg_parse_entry_t *table, + u_int num_entries, + const char *name, + u_int address, + u_int value, + u_int *cur_column, + u_int wrap_point); +/******************************* SEEPROM *************************************/ +int ahc_acquire_seeprom(struct ahc_softc *ahc, + struct seeprom_descriptor *sd); +void ahc_release_seeprom(struct seeprom_descriptor *sd); +#endif /* _AIC7XXX_H_ */ diff --git a/drivers/scsi/aic7xxx/aic7xxx.reg b/drivers/scsi/aic7xxx/aic7xxx.reg new file mode 100644 index 000000000..00fde2243 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx.reg @@ -0,0 +1,1761 @@ +/* + * Aic7xxx register and scratch ram definitions. + * + * Copyright (c) 1994-2001 Justin T. Gibbs. + * Copyright (c) 2000-2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $FreeBSD$ + */ +VERSION = "$Id: //depot/aic7xxx/aic7xxx/aic7xxx.reg#40 $" + +/* + * This file is processed by the aic7xxx_asm utility for use in assembling + * firmware for the aic7xxx family of SCSI host adapters as well as to generate + * a C header file for use in the kernel portion of the Aic7xxx driver. + * + * All page numbers refer to the Adaptec AIC-7770 Data Book available from + * Adaptec's Technical Documents Department 1-800-934-2766 + */ + +/* + * Registers marked "dont_generate_debug_code" are not (yet) referenced + * from the driver code, and this keyword inhibit generation + * of debug code for them. + * + * REG_PRETTY_PRINT config will complain if dont_generate_debug_code + * is added to the register which is referenced in the driver. + * Unreferenced register with no dont_generate_debug_code will result + * in dead code. No warning is issued. + */ + +/* + * SCSI Sequence Control (p. 3-11). + * Each bit, when set starts a specific SCSI sequence on the bus + */ +register SCSISEQ { + address 0x000 + access_mode RW + field TEMODE 0x80 + field ENSELO 0x40 + field ENSELI 0x20 + field ENRSELI 0x10 + field ENAUTOATNO 0x08 + field ENAUTOATNI 0x04 + field ENAUTOATNP 0x02 + field SCSIRSTO 0x01 +} + +/* + * SCSI Transfer Control 0 Register (pp. 3-13). + * Controls the SCSI module data path. + */ +register SXFRCTL0 { + address 0x001 + access_mode RW + field DFON 0x80 + field DFPEXP 0x40 + field FAST20 0x20 + field CLRSTCNT 0x10 + field SPIOEN 0x08 + field SCAMEN 0x04 + field CLRCHN 0x02 +} + +/* + * SCSI Transfer Control 1 Register (pp. 3-14,15). + * Controls the SCSI module data path. + */ +register SXFRCTL1 { + address 0x002 + access_mode RW + field BITBUCKET 0x80 + field SWRAPEN 0x40 + field ENSPCHK 0x20 + mask STIMESEL 0x18 + field ENSTIMER 0x04 + field ACTNEGEN 0x02 + field STPWEN 0x01 /* Powered Termination */ + dont_generate_debug_code +} + +/* + * SCSI Control Signal Read Register (p. 3-15). + * Reads the actual state of the SCSI bus pins + */ +register SCSISIGI { + address 0x003 + access_mode RO + field CDI 0x80 + field IOI 0x40 + field MSGI 0x20 + field ATNI 0x10 + field SELI 0x08 + field BSYI 0x04 + field REQI 0x02 + field ACKI 0x01 +/* + * Possible phases in SCSISIGI + */ + mask PHASE_MASK CDI|IOI|MSGI + mask P_DATAOUT 0x00 + mask P_DATAIN IOI + mask P_DATAOUT_DT P_DATAOUT|MSGI + mask P_DATAIN_DT P_DATAIN|MSGI + mask P_COMMAND CDI + mask P_MESGOUT CDI|MSGI + mask P_STATUS CDI|IOI + mask P_MESGIN CDI|IOI|MSGI +} + +/* + * SCSI Control Signal Write Register (p. 3-16). + * Writing to this register modifies the control signals on the bus. Only + * those signals that are allowed in the current mode (Initiator/Target) are + * asserted. + */ +register SCSISIGO { + address 0x003 + access_mode WO + field CDO 0x80 + field IOO 0x40 + field MSGO 0x20 + field ATNO 0x10 + field SELO 0x08 + field BSYO 0x04 + field REQO 0x02 + field ACKO 0x01 +/* + * Possible phases to write into SCSISIG0 + */ + mask PHASE_MASK CDI|IOI|MSGI + mask P_DATAOUT 0x00 + mask P_DATAIN IOI + mask P_COMMAND CDI + mask P_MESGOUT CDI|MSGI + mask P_STATUS CDI|IOI + mask P_MESGIN CDI|IOI|MSGI + dont_generate_debug_code +} + +/* + * SCSI Rate Control (p. 3-17). + * Contents of this register determine the Synchronous SCSI data transfer + * rate and the maximum synchronous Req/Ack offset. An offset of 0 in the + * SOFS (3:0) bits disables synchronous data transfers. Any offset value + * greater than 0 enables synchronous transfers. + */ +register SCSIRATE { + address 0x004 + access_mode RW + field WIDEXFER 0x80 /* Wide transfer control */ + field ENABLE_CRC 0x40 /* CRC for D-Phases */ + field SINGLE_EDGE 0x10 /* Disable DT Transfers */ + mask SXFR 0x70 /* Sync transfer rate */ + mask SXFR_ULTRA2 0x0f /* Sync transfer rate */ + mask SOFS 0x0f /* Sync offset */ +} + +/* + * SCSI ID (p. 3-18). + * Contains the ID of the board and the current target on the + * selected channel. + */ +register SCSIID { + address 0x005 + access_mode RW + mask TID 0xf0 /* Target ID mask */ + mask TWIN_TID 0x70 + field TWIN_CHNLB 0x80 + mask OID 0x0f /* Our ID mask */ + /* + * SCSI Maximum Offset (p. 4-61 aic7890/91 Data Book) + * The aic7890/91 allow an offset of up to 127 transfers in both wide + * and narrow mode. + */ + alias SCSIOFFSET + mask SOFS_ULTRA2 0x7f /* Sync offset U2 chips */ + dont_generate_debug_code +} + +/* + * SCSI Latched Data (p. 3-19). + * Read/Write latches used to transfer data on the SCSI bus during + * Automatic or Manual PIO mode. SCSIDATH can be used for the + * upper byte of a 16bit wide asynchronouse data phase transfer. + */ +register SCSIDATL { + address 0x006 + access_mode RW + dont_generate_debug_code +} + +register SCSIDATH { + address 0x007 + access_mode RW +} + +/* + * SCSI Transfer Count (pp. 3-19,20) + * These registers count down the number of bytes transferred + * across the SCSI bus. The counter is decremented only once + * the data has been safely transferred. SDONE in SSTAT0 is + * set when STCNT goes to 0 + */ +register STCNT { + address 0x008 + size 3 + access_mode RW + dont_generate_debug_code +} + +/* ALT_MODE registers (Ultra2 and Ultra160 chips) */ +register SXFRCTL2 { + address 0x013 + access_mode RW + field AUTORSTDIS 0x10 + field CMDDMAEN 0x08 + mask ASYNC_SETUP 0x07 +} + +/* ALT_MODE register on Ultra160 chips */ +register OPTIONMODE { + address 0x008 + access_mode RW + count 2 + field AUTORATEEN 0x80 + field AUTOACKEN 0x40 + field ATNMGMNTEN 0x20 + field BUSFREEREV 0x10 + field EXPPHASEDIS 0x08 + field SCSIDATL_IMGEN 0x04 + field AUTO_MSGOUT_DE 0x02 + field DIS_MSGIN_DUALEDGE 0x01 + mask OPTIONMODE_DEFAULTS AUTO_MSGOUT_DE|DIS_MSGIN_DUALEDGE + dont_generate_debug_code +} + +/* ALT_MODE register on Ultra160 chips */ +register TARGCRCCNT { + address 0x00a + size 2 + access_mode RW + count 2 + dont_generate_debug_code +} + +/* + * Clear SCSI Interrupt 0 (p. 3-20) + * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT0. + */ +register CLRSINT0 { + address 0x00b + access_mode WO + field CLRSELDO 0x40 + field CLRSELDI 0x20 + field CLRSELINGO 0x10 + field CLRSWRAP 0x08 + field CLRIOERR 0x08 /* Ultra2 Only */ + field CLRSPIORDY 0x02 + dont_generate_debug_code +} + +/* + * SCSI Status 0 (p. 3-21) + * Contains one set of SCSI Interrupt codes + * These are most likely of interest to the sequencer + */ +register SSTAT0 { + address 0x00b + access_mode RO + field TARGET 0x80 /* Board acting as target */ + field SELDO 0x40 /* Selection Done */ + field SELDI 0x20 /* Board has been selected */ + field SELINGO 0x10 /* Selection In Progress */ + field SWRAP 0x08 /* 24bit counter wrap */ + field IOERR 0x08 /* LVD Tranceiver mode changed */ + field SDONE 0x04 /* STCNT = 0x000000 */ + field SPIORDY 0x02 /* SCSI PIO Ready */ + field DMADONE 0x01 /* DMA transfer completed */ +} + +/* + * Clear SCSI Interrupt 1 (p. 3-23) + * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT1. + */ +register CLRSINT1 { + address 0x00c + access_mode WO + field CLRSELTIMEO 0x80 + field CLRATNO 0x40 + field CLRSCSIRSTI 0x20 + field CLRBUSFREE 0x08 + field CLRSCSIPERR 0x04 + field CLRPHASECHG 0x02 + field CLRREQINIT 0x01 + dont_generate_debug_code +} + +/* + * SCSI Status 1 (p. 3-24) + */ +register SSTAT1 { + address 0x00c + access_mode RO + field SELTO 0x80 + field ATNTARG 0x40 + field SCSIRSTI 0x20 + field PHASEMIS 0x10 + field BUSFREE 0x08 + field SCSIPERR 0x04 + field PHASECHG 0x02 + field REQINIT 0x01 +} + +/* + * SCSI Status 2 (pp. 3-25,26) + */ +register SSTAT2 { + address 0x00d + access_mode RO + field OVERRUN 0x80 + field SHVALID 0x40 /* Shadow Layer non-zero */ + field EXP_ACTIVE 0x10 /* SCSI Expander Active */ + field CRCVALERR 0x08 /* CRC doesn't match (U3 only) */ + field CRCENDERR 0x04 /* No terminal CRC packet (U3 only) */ + field CRCREQERR 0x02 /* Illegal CRC packet req (U3 only) */ + field DUAL_EDGE_ERR 0x01 /* Incorrect data phase (U3 only) */ + mask SFCNT 0x1f +} + +/* + * SCSI Status 3 (p. 3-26) + */ +register SSTAT3 { + address 0x00e + access_mode RO + count 2 + mask SCSICNT 0xf0 + mask OFFCNT 0x0f + mask U2OFFCNT 0x7f +} + +/* + * SCSI ID for the aic7890/91 chips + */ +register SCSIID_ULTRA2 { + address 0x00f + access_mode RW + mask TID 0xf0 /* Target ID mask */ + mask OID 0x0f /* Our ID mask */ + dont_generate_debug_code +} + +/* + * SCSI Interrupt Mode 1 (p. 3-28) + * Setting any bit will enable the corresponding function + * in SIMODE0 to interrupt via the IRQ pin. + */ +register SIMODE0 { + address 0x010 + access_mode RW + count 2 + field ENSELDO 0x40 + field ENSELDI 0x20 + field ENSELINGO 0x10 + field ENSWRAP 0x08 + field ENIOERR 0x08 /* LVD Tranceiver mode changes */ + field ENSDONE 0x04 + field ENSPIORDY 0x02 + field ENDMADONE 0x01 +} + +/* + * SCSI Interrupt Mode 1 (pp. 3-28,29) + * Setting any bit will enable the corresponding function + * in SIMODE1 to interrupt via the IRQ pin. + */ +register SIMODE1 { + address 0x011 + access_mode RW + field ENSELTIMO 0x80 + field ENATNTARG 0x40 + field ENSCSIRST 0x20 + field ENPHASEMIS 0x10 + field ENBUSFREE 0x08 + field ENSCSIPERR 0x04 + field ENPHASECHG 0x02 + field ENREQINIT 0x01 +} + +/* + * SCSI Data Bus (High) (p. 3-29) + * This register reads data on the SCSI Data bus directly. + */ +register SCSIBUSL { + address 0x012 + access_mode RW +} + +register SCSIBUSH { + address 0x013 + access_mode RW +} + +/* + * SCSI/Host Address (p. 3-30) + * These registers hold the host address for the byte about to be + * transferred on the SCSI bus. They are counted up in the same + * manner as STCNT is counted down. SHADDR should always be used + * to determine the address of the last byte transferred since HADDR + * can be skewed by write ahead. + */ +register SHADDR { + address 0x014 + size 4 + access_mode RO + dont_generate_debug_code +} + +/* + * Selection Timeout Timer (p. 3-30) + */ +register SELTIMER { + address 0x018 + access_mode RW + count 1 + field STAGE6 0x20 + field STAGE5 0x10 + field STAGE4 0x08 + field STAGE3 0x04 + field STAGE2 0x02 + field STAGE1 0x01 + alias TARGIDIN + dont_generate_debug_code +} + +/* + * Selection/Reselection ID (p. 3-31) + * Upper four bits are the device id. The ONEBIT is set when the re/selecting + * device did not set its own ID. + */ +register SELID { + address 0x019 + access_mode RW + mask SELID_MASK 0xf0 + field ONEBIT 0x08 + dont_generate_debug_code +} + +register SCAMCTL { + address 0x01a + access_mode RW + field ENSCAMSELO 0x80 + field CLRSCAMSELID 0x40 + field ALTSTIM 0x20 + field DFLTTID 0x10 + mask SCAMLVL 0x03 +} + +/* + * Target Mode Selecting in ID bitmask (aic7890/91/96/97) + */ +register TARGID { + address 0x01b + size 2 + access_mode RW + count 14 + dont_generate_debug_code +} + +/* + * Serial Port I/O Cabability register (p. 4-95 aic7860 Data Book) + * Indicates if external logic has been attached to the chip to + * perform the tasks of accessing a serial eeprom, testing termination + * strength, and performing cable detection. On the aic7860, most of + * these features are handled on chip, but on the aic7855 an attached + * aic3800 does the grunt work. + */ +register SPIOCAP { + address 0x01b + access_mode RW + count 10 + field SOFT1 0x80 + field SOFT0 0x40 + field SOFTCMDEN 0x20 + field EXT_BRDCTL 0x10 /* External Board control */ + field SEEPROM 0x08 /* External serial eeprom logic */ + field EEPROM 0x04 /* Writable external BIOS ROM */ + field ROM 0x02 /* Logic for accessing external ROM */ + field SSPIOCPS 0x01 /* Termination and cable detection */ + dont_generate_debug_code +} + +register BRDCTL { + address 0x01d + count 11 + field BRDDAT7 0x80 + field BRDDAT6 0x40 + field BRDDAT5 0x20 + field BRDSTB 0x10 + field BRDCS 0x08 + field BRDRW 0x04 + field BRDCTL1 0x02 + field BRDCTL0 0x01 + /* 7890 Definitions */ + field BRDDAT4 0x10 + field BRDDAT3 0x08 + field BRDDAT2 0x04 + field BRDRW_ULTRA2 0x02 + field BRDSTB_ULTRA2 0x01 + dont_generate_debug_code +} + +/* + * Serial EEPROM Control (p. 4-92 in 7870 Databook) + * Controls the reading and writing of an external serial 1-bit + * EEPROM Device. In order to access the serial EEPROM, you must + * first set the SEEMS bit that generates a request to the memory + * port for access to the serial EEPROM device. When the memory + * port is not busy servicing another request, it reconfigures + * to allow access to the serial EEPROM. When this happens, SEERDY + * gets set high to verify that the memory port access has been + * granted. + * + * After successful arbitration for the memory port, the SEECS bit of + * the SEECTL register is connected to the chip select. The SEECK, + * SEEDO, and SEEDI are connected to the clock, data out, and data in + * lines respectively. The SEERDY bit of SEECTL is useful in that it + * gives us an 800 nsec timer. After a write to the SEECTL register, + * the SEERDY goes high 800 nsec later. The one exception to this is + * when we first request access to the memory port. The SEERDY goes + * high to signify that access has been granted and, for this case, has + * no implied timing. + * + * See 93cx6.c for detailed information on the protocol necessary to + * read the serial EEPROM. + */ +register SEECTL { + address 0x01e + count 11 + field EXTARBACK 0x80 + field EXTARBREQ 0x40 + field SEEMS 0x20 + field SEERDY 0x10 + field SEECS 0x08 + field SEECK 0x04 + field SEEDO 0x02 + field SEEDI 0x01 + dont_generate_debug_code +} +/* + * SCSI Block Control (p. 3-32) + * Controls Bus type and channel selection. In a twin channel configuration + * addresses 0x00-0x1e are gated to the appropriate channel based on this + * register. SELWIDE allows for the coexistence of 8bit and 16bit devices + * on a wide bus. + */ +register SBLKCTL { + address 0x01f + access_mode RW + field DIAGLEDEN 0x80 /* Aic78X0 only */ + field DIAGLEDON 0x40 /* Aic78X0 only */ + field AUTOFLUSHDIS 0x20 + field SELBUSB 0x08 + field ENAB40 0x08 /* LVD transceiver active */ + field ENAB20 0x04 /* SE/HVD transceiver active */ + field SELWIDE 0x02 + field XCVR 0x01 /* External transceiver active */ +} + +/* + * Sequencer Control (p. 3-33) + * Error detection mode and speed configuration + */ +register SEQCTL { + address 0x060 + access_mode RW + count 15 + field PERRORDIS 0x80 + field PAUSEDIS 0x40 + field FAILDIS 0x20 + field FASTMODE 0x10 + field BRKADRINTEN 0x08 + field STEP 0x04 + field SEQRESET 0x02 + field LOADRAM 0x01 +} + +/* + * Sequencer RAM Data (p. 3-34) + * Single byte window into the Scratch Ram area starting at the address + * specified by SEQADDR0 and SEQADDR1. To write a full word, simply write + * four bytes in succession. The SEQADDRs will increment after the most + * significant byte is written + */ +register SEQRAM { + address 0x061 + access_mode RW + count 2 + dont_generate_debug_code +} + +/* + * Sequencer Address Registers (p. 3-35) + * Only the first bit of SEQADDR1 holds addressing information + */ +register SEQADDR0 { + address 0x062 + access_mode RW + dont_generate_debug_code +} + +register SEQADDR1 { + address 0x063 + access_mode RW + count 8 + mask SEQADDR1_MASK 0x01 + dont_generate_debug_code +} + +/* + * Accumulator + * We cheat by passing arguments in the Accumulator up to the kernel driver + */ +register ACCUM { + address 0x064 + access_mode RW + accumulator + dont_generate_debug_code +} + +register SINDEX { + address 0x065 + access_mode RW + sindex + dont_generate_debug_code +} + +register DINDEX { + address 0x066 + access_mode RW + dont_generate_debug_code +} + +register ALLONES { + address 0x069 + access_mode RO + allones + dont_generate_debug_code +} + +register ALLZEROS { + address 0x06a + access_mode RO + allzeros + dont_generate_debug_code +} + +register NONE { + address 0x06a + access_mode WO + none + dont_generate_debug_code +} + +register FLAGS { + address 0x06b + access_mode RO + count 18 + field ZERO 0x02 + field CARRY 0x01 + dont_generate_debug_code +} + +register SINDIR { + address 0x06c + access_mode RO + dont_generate_debug_code +} + +register DINDIR { + address 0x06d + access_mode WO + dont_generate_debug_code +} + +register FUNCTION1 { + address 0x06e + access_mode RW +} + +register STACK { + address 0x06f + access_mode RO + count 5 + dont_generate_debug_code +} + +const STACK_SIZE 4 + +/* + * Board Control (p. 3-43) + */ +register BCTL { + address 0x084 + access_mode RW + field ACE 0x08 + field ENABLE 0x01 +} + +/* + * On the aic78X0 chips, Board Control is replaced by the DSCommand + * register (p. 4-64) + */ +register DSCOMMAND0 { + address 0x084 + access_mode RW + count 7 + field CACHETHEN 0x80 /* Cache Threshold enable */ + field DPARCKEN 0x40 /* Data Parity Check Enable */ + field MPARCKEN 0x20 /* Memory Parity Check Enable */ + field EXTREQLCK 0x10 /* External Request Lock */ + /* aic7890/91/96/97 only */ + field INTSCBRAMSEL 0x08 /* Internal SCB RAM Select */ + field RAMPS 0x04 /* External SCB RAM Present */ + field USCBSIZE32 0x02 /* Use 32byte SCB Page Size */ + field CIOPARCKEN 0x01 /* Internal bus parity error enable */ + dont_generate_debug_code +} + +register DSCOMMAND1 { + address 0x085 + access_mode RW + mask DSLATT 0xfc /* PCI latency timer (non-ultra2) */ + field HADDLDSEL1 0x02 /* Host Address Load Select Bits */ + field HADDLDSEL0 0x01 + dont_generate_debug_code +} + +/* + * Bus On/Off Time (p. 3-44) aic7770 only + */ +register BUSTIME { + address 0x085 + access_mode RW + count 2 + mask BOFF 0xf0 + mask BON 0x0f + dont_generate_debug_code +} + +/* + * Bus Speed (p. 3-45) aic7770 only + */ +register BUSSPD { + address 0x086 + access_mode RW + count 2 + mask DFTHRSH 0xc0 + mask STBOFF 0x38 + mask STBON 0x07 + mask DFTHRSH_100 0xc0 + mask DFTHRSH_75 0x80 + dont_generate_debug_code +} + +/* aic7850/55/60/70/80/95 only */ +register DSPCISTATUS { + address 0x086 + count 4 + mask DFTHRSH_100 0xc0 + dont_generate_debug_code +} + +/* aic7890/91/96/97 only */ +register HS_MAILBOX { + address 0x086 + mask HOST_MAILBOX 0xF0 + mask SEQ_MAILBOX 0x0F + mask HOST_TQINPOS 0x80 /* Boundary at either 0 or 128 */ + dont_generate_debug_code +} + +const HOST_MAILBOX_SHIFT 4 +const SEQ_MAILBOX_SHIFT 0 + +/* + * Host Control (p. 3-47) R/W + * Overall host control of the device. + */ +register HCNTRL { + address 0x087 + access_mode RW + count 14 + field POWRDN 0x40 + field SWINT 0x10 + field IRQMS 0x08 + field PAUSE 0x04 + field INTEN 0x02 + field CHIPRST 0x01 + field CHIPRSTACK 0x01 + dont_generate_debug_code +} + +/* + * Host Address (p. 3-48) + * This register contains the address of the byte about + * to be transferred across the host bus. + */ +register HADDR { + address 0x088 + size 4 + access_mode RW + dont_generate_debug_code +} + +register HCNT { + address 0x08c + size 3 + access_mode RW + dont_generate_debug_code +} + +/* + * SCB Pointer (p. 3-49) + * Gate one of the SCBs into the SCBARRAY window. + */ +register SCBPTR { + address 0x090 + access_mode RW + dont_generate_debug_code +} + +/* + * Interrupt Status (p. 3-50) + * Status for system interrupts + */ +register INTSTAT { + address 0x091 + access_mode RW + field BRKADRINT 0x08 + field SCSIINT 0x04 + field CMDCMPLT 0x02 + field SEQINT 0x01 + mask BAD_PHASE SEQINT /* unknown scsi bus phase */ + mask SEND_REJECT 0x10|SEQINT /* sending a message reject */ + mask PROTO_VIOLATION 0x20|SEQINT /* SCSI protocol violation */ + mask NO_MATCH 0x30|SEQINT /* no cmd match for reconnect */ + mask IGN_WIDE_RES 0x40|SEQINT /* Complex IGN Wide Res Msg */ + mask PDATA_REINIT 0x50|SEQINT /* + * Returned to data phase + * that requires data + * transfer pointers to be + * recalculated from the + * transfer residual. + */ + mask HOST_MSG_LOOP 0x60|SEQINT /* + * The bus is ready for the + * host to perform another + * message transaction. This + * mechanism is used for things + * like sync/wide negotiation + * that require a kernel based + * message state engine. + */ + mask BAD_STATUS 0x70|SEQINT /* Bad status from target */ + mask PERR_DETECTED 0x80|SEQINT /* + * Either the phase_lock + * or inb_next routine has + * noticed a parity error. + */ + mask DATA_OVERRUN 0x90|SEQINT /* + * Target attempted to write + * beyond the bounds of its + * command. + */ + mask MKMSG_FAILED 0xa0|SEQINT /* + * Target completed command + * without honoring our ATN + * request to issue a message. + */ + mask MISSED_BUSFREE 0xb0|SEQINT /* + * The sequencer never saw + * the bus go free after + * either a command complete + * or disconnect message. + */ + mask SCB_MISMATCH 0xc0|SEQINT /* + * Downloaded SCB's tag does + * not match the entry we + * intended to download. + */ + mask NO_FREE_SCB 0xd0|SEQINT /* + * get_free_or_disc_scb failed. + */ + mask OUT_OF_RANGE 0xe0|SEQINT + + mask SEQINT_MASK 0xf0|SEQINT /* SEQINT Status Codes */ + mask INT_PEND (BRKADRINT|SEQINT|SCSIINT|CMDCMPLT) + dont_generate_debug_code +} + +/* + * Hard Error (p. 3-53) + * Reporting of catastrophic errors. You usually cannot recover from + * these without a full board reset. + */ +register ERROR { + address 0x092 + access_mode RO + count 26 + field CIOPARERR 0x80 /* Ultra2 only */ + field PCIERRSTAT 0x40 /* PCI only */ + field MPARERR 0x20 /* PCI only */ + field DPARERR 0x10 /* PCI only */ + field SQPARERR 0x08 + field ILLOPCODE 0x04 + field ILLSADDR 0x02 + field ILLHADDR 0x01 +} + +/* + * Clear Interrupt Status (p. 3-52) + */ +register CLRINT { + address 0x092 + access_mode WO + count 24 + field CLRPARERR 0x10 /* PCI only */ + field CLRBRKADRINT 0x08 + field CLRSCSIINT 0x04 + field CLRCMDINT 0x02 + field CLRSEQINT 0x01 + dont_generate_debug_code +} + +register DFCNTRL { + address 0x093 + access_mode RW + field PRELOADEN 0x80 /* aic7890 only */ + field WIDEODD 0x40 + field SCSIEN 0x20 + field SDMAEN 0x10 + field SDMAENACK 0x10 + field HDMAEN 0x08 + field HDMAENACK 0x08 + field DIRECTION 0x04 + field FIFOFLUSH 0x02 + field FIFORESET 0x01 +} + +register DFSTATUS { + address 0x094 + access_mode RO + field PRELOAD_AVAIL 0x80 + field DFCACHETH 0x40 + field FIFOQWDEMP 0x20 + field MREQPEND 0x10 + field HDONE 0x08 + field DFTHRESH 0x04 + field FIFOFULL 0x02 + field FIFOEMP 0x01 +} + +register DFWADDR { + address 0x95 + access_mode RW + dont_generate_debug_code +} + +register DFRADDR { + address 0x97 + access_mode RW +} + +register DFDAT { + address 0x099 + access_mode RW + dont_generate_debug_code +} + +/* + * SCB Auto Increment (p. 3-59) + * Byte offset into the SCB Array and an optional bit to allow auto + * incrementing of the address during download and upload operations + */ +register SCBCNT { + address 0x09a + access_mode RW + count 1 + field SCBAUTO 0x80 + mask SCBCNT_MASK 0x1f + dont_generate_debug_code +} + +/* + * Queue In FIFO (p. 3-60) + * Input queue for queued SCBs (commands that the seqencer has yet to start) + */ +register QINFIFO { + address 0x09b + access_mode RW + count 12 + dont_generate_debug_code +} + +/* + * Queue In Count (p. 3-60) + * Number of queued SCBs + */ +register QINCNT { + address 0x09c + access_mode RO +} + +/* + * Queue Out FIFO (p. 3-61) + * Queue of SCBs that have completed and await the host + */ +register QOUTFIFO { + address 0x09d + access_mode WO + count 7 + dont_generate_debug_code +} + +register CRCCONTROL1 { + address 0x09d + access_mode RW + count 3 + field CRCONSEEN 0x80 + field CRCVALCHKEN 0x40 + field CRCENDCHKEN 0x20 + field CRCREQCHKEN 0x10 + field TARGCRCENDEN 0x08 + field TARGCRCCNTEN 0x04 + dont_generate_debug_code +} + + +/* + * Queue Out Count (p. 3-61) + * Number of queued SCBs in the Out FIFO + */ +register QOUTCNT { + address 0x09e + access_mode RO +} + +register SCSIPHASE { + address 0x09e + access_mode RO + field STATUS_PHASE 0x20 + field COMMAND_PHASE 0x10 + field MSG_IN_PHASE 0x08 + field MSG_OUT_PHASE 0x04 + field DATA_IN_PHASE 0x02 + field DATA_OUT_PHASE 0x01 + mask DATA_PHASE_MASK 0x03 +} + +/* + * Special Function + */ +register SFUNCT { + address 0x09f + access_mode RW + count 4 + field ALT_MODE 0x80 + dont_generate_debug_code +} + +/* + * SCB Definition (p. 5-4) + */ +scb { + address 0x0a0 + size 64 + + SCB_CDB_PTR { + size 4 + alias SCB_RESIDUAL_DATACNT + alias SCB_CDB_STORE + dont_generate_debug_code + } + SCB_RESIDUAL_SGPTR { + size 4 + dont_generate_debug_code + } + SCB_SCSI_STATUS { + size 1 + dont_generate_debug_code + } + SCB_TARGET_PHASES { + size 1 + dont_generate_debug_code + } + SCB_TARGET_DATA_DIR { + size 1 + dont_generate_debug_code + } + SCB_TARGET_ITAG { + size 1 + dont_generate_debug_code + } + SCB_DATAPTR { + size 4 + dont_generate_debug_code + } + SCB_DATACNT { + /* + * The last byte is really the high address bits for + * the data address. + */ + size 4 + field SG_LAST_SEG 0x80 /* In the fourth byte */ + mask SG_HIGH_ADDR_BITS 0x7F /* In the fourth byte */ + dont_generate_debug_code + } + SCB_SGPTR { + size 4 + field SG_RESID_VALID 0x04 /* In the first byte */ + field SG_FULL_RESID 0x02 /* In the first byte */ + field SG_LIST_NULL 0x01 /* In the first byte */ + dont_generate_debug_code + } + SCB_CONTROL { + size 1 + field TARGET_SCB 0x80 + field STATUS_RCVD 0x80 + field DISCENB 0x40 + field TAG_ENB 0x20 + field MK_MESSAGE 0x10 + field ULTRAENB 0x08 + field DISCONNECTED 0x04 + mask SCB_TAG_TYPE 0x03 + } + SCB_SCSIID { + size 1 + field TWIN_CHNLB 0x80 + mask TWIN_TID 0x70 + mask TID 0xf0 + mask OID 0x0f + } + SCB_LUN { + field SCB_XFERLEN_ODD 0x80 + mask LID 0x3f + size 1 + } + SCB_TAG { + size 1 + } + SCB_CDB_LEN { + size 1 + dont_generate_debug_code + } + SCB_SCSIRATE { + size 1 + dont_generate_debug_code + } + SCB_SCSIOFFSET { + size 1 + count 1 + dont_generate_debug_code + } + SCB_NEXT { + size 1 + dont_generate_debug_code + } + SCB_64_SPARE { + size 16 + } + SCB_64_BTT { + size 16 + dont_generate_debug_code + } +} + +const SCB_UPLOAD_SIZE 32 +const SCB_DOWNLOAD_SIZE 32 +const SCB_DOWNLOAD_SIZE_64 48 + +const SG_SIZEOF 0x08 /* sizeof(struct ahc_dma) */ + +/* --------------------- AHA-2840-only definitions -------------------- */ + +register SEECTL_2840 { + address 0x0c0 + access_mode RW + count 2 + field CS_2840 0x04 + field CK_2840 0x02 + field DO_2840 0x01 + dont_generate_debug_code +} + +register STATUS_2840 { + address 0x0c1 + access_mode RW + count 4 + field EEPROM_TF 0x80 + mask BIOS_SEL 0x60 + mask ADSEL 0x1e + field DI_2840 0x01 + dont_generate_debug_code +} + +/* --------------------- AIC-7870-only definitions -------------------- */ + +register CCHADDR { + address 0x0E0 + size 8 + dont_generate_debug_code +} + +register CCHCNT { + address 0x0E8 + dont_generate_debug_code +} + +register CCSGRAM { + address 0x0E9 + dont_generate_debug_code +} + +register CCSGADDR { + address 0x0EA + dont_generate_debug_code +} + +register CCSGCTL { + address 0x0EB + field CCSGDONE 0x80 + field CCSGEN 0x08 + field SG_FETCH_NEEDED 0x02 /* Bit used for software state */ + field CCSGRESET 0x01 + dont_generate_debug_code +} + +register CCSCBCNT { + address 0xEF + count 1 + dont_generate_debug_code +} + +register CCSCBCTL { + address 0x0EE + field CCSCBDONE 0x80 + field ARRDONE 0x40 /* SCB Array prefetch done */ + field CCARREN 0x10 + field CCSCBEN 0x08 + field CCSCBDIR 0x04 + field CCSCBRESET 0x01 + dont_generate_debug_code +} + +register CCSCBADDR { + address 0x0ED + dont_generate_debug_code +} + +register CCSCBRAM { + address 0xEC + dont_generate_debug_code +} + +/* + * SCB bank address (7895/7896/97 only) + */ +register SCBBADDR { + address 0x0F0 + access_mode RW + count 3 + dont_generate_debug_code +} + +register CCSCBPTR { + address 0x0F1 + dont_generate_debug_code +} + +register HNSCB_QOFF { + address 0x0F4 + count 4 + dont_generate_debug_code +} + +register SNSCB_QOFF { + address 0x0F6 + dont_generate_debug_code +} + +register SDSCB_QOFF { + address 0x0F8 + dont_generate_debug_code +} + +register QOFF_CTLSTA { + address 0x0FA + field SCB_AVAIL 0x40 + field SNSCB_ROLLOVER 0x20 + field SDSCB_ROLLOVER 0x10 + mask SCB_QSIZE 0x07 + mask SCB_QSIZE_256 0x06 + dont_generate_debug_code +} + +register DFF_THRSH { + address 0x0FB + mask WR_DFTHRSH 0x70 + mask RD_DFTHRSH 0x07 + mask RD_DFTHRSH_MIN 0x00 + mask RD_DFTHRSH_25 0x01 + mask RD_DFTHRSH_50 0x02 + mask RD_DFTHRSH_63 0x03 + mask RD_DFTHRSH_75 0x04 + mask RD_DFTHRSH_85 0x05 + mask RD_DFTHRSH_90 0x06 + mask RD_DFTHRSH_MAX 0x07 + mask WR_DFTHRSH_MIN 0x00 + mask WR_DFTHRSH_25 0x10 + mask WR_DFTHRSH_50 0x20 + mask WR_DFTHRSH_63 0x30 + mask WR_DFTHRSH_75 0x40 + mask WR_DFTHRSH_85 0x50 + mask WR_DFTHRSH_90 0x60 + mask WR_DFTHRSH_MAX 0x70 + count 4 + dont_generate_debug_code +} + +register SG_CACHE_PRE { + access_mode WO + address 0x0fc + mask SG_ADDR_MASK 0xf8 + field LAST_SEG 0x02 + field LAST_SEG_DONE 0x01 + dont_generate_debug_code +} + +register SG_CACHE_SHADOW { + access_mode RO + address 0x0fc + mask SG_ADDR_MASK 0xf8 + field LAST_SEG 0x02 + field LAST_SEG_DONE 0x01 + dont_generate_debug_code +} +/* ---------------------- Scratch RAM Offsets ------------------------- */ +/* These offsets are either to values that are initialized by the board's + * BIOS or are specified by the sequencer code. + * + * The host adapter card (at least the BIOS) uses 20-2f for SCSI + * device information, 32-33 and 5a-5f as well. As it turns out, the + * BIOS trashes 20-2f, writing the synchronous negotiation results + * on top of the BIOS values, so we re-use those for our per-target + * scratchspace (actually a value that can be copied directly into + * SCSIRATE). The kernel driver will enable synchronous negotiation + * for all targets that have a value other than 0 in the lower four + * bits of the target scratch space. This should work regardless of + * whether the bios has been installed. + */ + +scratch_ram { + address 0x020 + size 58 + + /* + * 1 byte per target starting at this address for configuration values + */ + BUSY_TARGETS { + alias TARG_SCSIRATE + size 16 + dont_generate_debug_code + } + /* + * Bit vector of targets that have ULTRA enabled as set by + * the BIOS. The Sequencer relies on a per-SCB field to + * control whether to enable Ultra transfers or not. During + * initialization, we read this field and reuse it for 2 + * entries in the busy target table. + */ + ULTRA_ENB { + alias CMDSIZE_TABLE + size 2 + count 2 + dont_generate_debug_code + } + /* + * Bit vector of targets that have disconnection disabled as set by + * the BIOS. The Sequencer relies in a per-SCB field to control the + * disconnect priveldge. During initialization, we read this field + * and reuse it for 2 entries in the busy target table. + */ + DISC_DSB { + size 2 + count 6 + dont_generate_debug_code + } + CMDSIZE_TABLE_TAIL { + size 4 + } + /* + * Partial transfer past cacheline end to be + * transferred using an extra S/G. + */ + MWI_RESIDUAL { + size 1 + dont_generate_debug_code + } + /* + * SCBID of the next SCB to be started by the controller. + */ + NEXT_QUEUED_SCB { + size 1 + dont_generate_debug_code + } + /* + * Single byte buffer used to designate the type or message + * to send to a target. + */ + MSG_OUT { + size 1 + dont_generate_debug_code + } + /* Parameters for DMA Logic */ + DMAPARAMS { + size 1 + count 12 + field PRELOADEN 0x80 + field WIDEODD 0x40 + field SCSIEN 0x20 + field SDMAEN 0x10 + field SDMAENACK 0x10 + field HDMAEN 0x08 + field HDMAENACK 0x08 + field DIRECTION 0x04 /* Set indicates PCI->SCSI */ + field FIFOFLUSH 0x02 + field FIFORESET 0x01 + dont_generate_debug_code + } + SEQ_FLAGS { + size 1 + field NOT_IDENTIFIED 0x80 + field NO_CDB_SENT 0x40 + field TARGET_CMD_IS_TAGGED 0x40 + field DPHASE 0x20 + /* Target flags */ + field TARG_CMD_PENDING 0x10 + field CMDPHASE_PENDING 0x08 + field DPHASE_PENDING 0x04 + field SPHASE_PENDING 0x02 + field NO_DISCONNECT 0x01 + } + /* + * Temporary storage for the + * target/channel/lun of a + * reconnecting target + */ + SAVED_SCSIID { + size 1 + dont_generate_debug_code + } + SAVED_LUN { + size 1 + dont_generate_debug_code + } + /* + * The last bus phase as seen by the sequencer. + */ + LASTPHASE { + size 1 + field CDI 0x80 + field IOI 0x40 + field MSGI 0x20 + mask PHASE_MASK CDI|IOI|MSGI + mask P_DATAOUT 0x00 + mask P_DATAIN IOI + mask P_COMMAND CDI + mask P_MESGOUT CDI|MSGI + mask P_STATUS CDI|IOI + mask P_MESGIN CDI|IOI|MSGI + mask P_BUSFREE 0x01 + } + /* + * head of list of SCBs awaiting + * selection + */ + WAITING_SCBH { + size 1 + dont_generate_debug_code + } + /* + * head of list of SCBs that are + * disconnected. Used for SCB + * paging. + */ + DISCONNECTED_SCBH { + size 1 + dont_generate_debug_code + } + /* + * head of list of SCBs that are + * not in use. Used for SCB paging. + */ + FREE_SCBH { + size 1 + dont_generate_debug_code + } + /* + * head of list of SCBs that have + * completed but have not been + * put into the qoutfifo. + */ + COMPLETE_SCBH { + size 1 + } + /* + * Address of the hardware scb array in the host. + */ + HSCB_ADDR { + size 4 + dont_generate_debug_code + } + /* + * Base address of our shared data with the kernel driver in host + * memory. This includes the qoutfifo and target mode + * incoming command queue. + */ + SHARED_DATA_ADDR { + size 4 + dont_generate_debug_code + } + KERNEL_QINPOS { + size 1 + dont_generate_debug_code + } + QINPOS { + size 1 + dont_generate_debug_code + } + QOUTPOS { + size 1 + dont_generate_debug_code + } + /* + * Kernel and sequencer offsets into the queue of + * incoming target mode command descriptors. The + * queue is full when the KERNEL_TQINPOS == TQINPOS. + */ + KERNEL_TQINPOS { + size 1 + dont_generate_debug_code + } + TQINPOS { + size 1 + dont_generate_debug_code + } + ARG_1 { + size 1 + count 1 + mask SEND_MSG 0x80 + mask SEND_SENSE 0x40 + mask SEND_REJ 0x20 + mask MSGOUT_PHASEMIS 0x10 + mask EXIT_MSG_LOOP 0x08 + mask CONT_MSG_LOOP 0x04 + mask CONT_TARG_SESSION 0x02 + alias RETURN_1 + dont_generate_debug_code + } + ARG_2 { + size 1 + alias RETURN_2 + dont_generate_debug_code + } + + /* + * Snapshot of MSG_OUT taken after each message is sent. + */ + LAST_MSG { + size 1 + alias TARG_IMMEDIATE_SCB + dont_generate_debug_code + } + + /* + * Sequences the kernel driver has okayed for us. This allows + * the driver to do things like prevent initiator or target + * operations. + */ + SCSISEQ_TEMPLATE { + size 1 + field ENSELO 0x40 + field ENSELI 0x20 + field ENRSELI 0x10 + field ENAUTOATNO 0x08 + field ENAUTOATNI 0x04 + field ENAUTOATNP 0x02 + dont_generate_debug_code + } +} + +scratch_ram { + address 0x056 + size 4 + /* + * These scratch ram locations are initialized by the 274X BIOS. + * We reuse them after capturing the BIOS settings during + * initialization. + */ + + /* + * The initiator specified tag for this target mode transaction. + */ + HA_274_BIOSGLOBAL { + size 1 + field HA_274_EXTENDED_TRANS 0x01 + alias INITIATOR_TAG + count 1 + dont_generate_debug_code + } + + SEQ_FLAGS2 { + size 1 + field SCB_DMA 0x01 + field TARGET_MSG_PENDING 0x02 + dont_generate_debug_code + } +} + +scratch_ram { + address 0x05a + size 6 + /* + * These are reserved registers in the card's scratch ram on the 2742. + * The EISA configuration chip is mapped here. On Rev E. of the + * aic7770, the sequencer can use this area for scratch, but the + * host cannot directly access these registers. On later chips, this + * area can be read and written by both the host and the sequencer. + * Even on later chips, many of these locations are initialized by + * the BIOS. + */ + SCSICONF { + size 1 + count 12 + field TERM_ENB 0x80 + field RESET_SCSI 0x40 + field ENSPCHK 0x20 + mask HSCSIID 0x07 /* our SCSI ID */ + mask HWSCSIID 0x0f /* our SCSI ID if Wide Bus */ + dont_generate_debug_code + } + INTDEF { + address 0x05c + size 1 + count 1 + field EDGE_TRIG 0x80 + mask VECTOR 0x0f + dont_generate_debug_code + } + HOSTCONF { + address 0x05d + size 1 + count 1 + dont_generate_debug_code + } + HA_274_BIOSCTRL { + address 0x05f + size 1 + count 1 + mask BIOSMODE 0x30 + mask BIOSDISABLED 0x30 + field CHANNEL_B_PRIMARY 0x08 + dont_generate_debug_code + } +} + +scratch_ram { + address 0x070 + size 16 + + /* + * Per target SCSI offset values for Ultra2 controllers. + */ + TARG_OFFSET { + size 16 + count 1 + dont_generate_debug_code + } +} + +const TID_SHIFT 4 +const SCB_LIST_NULL 0xff +const TARGET_CMD_CMPLT 0xfe + +const CCSGADDR_MAX 0x80 +const CCSGRAM_MAXSEGS 16 + +/* WDTR Message values */ +const BUS_8_BIT 0x00 +const BUS_16_BIT 0x01 +const BUS_32_BIT 0x02 + +/* Offset maximums */ +const MAX_OFFSET_8BIT 0x0f +const MAX_OFFSET_16BIT 0x08 +const MAX_OFFSET_ULTRA2 0x7f +const MAX_OFFSET 0x7f +const HOST_MSG 0xff + +/* Target mode command processing constants */ +const CMD_GROUP_CODE_SHIFT 0x05 + +const STATUS_BUSY 0x08 +const STATUS_QUEUE_FULL 0x28 +const TARGET_DATA_IN 1 + +/* + * Downloaded (kernel inserted) constants + */ +/* Offsets into the SCBID array where different data is stored */ +const QOUTFIFO_OFFSET download +const QINFIFO_OFFSET download +const CACHESIZE_MASK download +const INVERTED_CACHESIZE_MASK download +const SG_PREFETCH_CNT download +const SG_PREFETCH_ALIGN_MASK download +const SG_PREFETCH_ADDR_MASK download diff --git a/drivers/scsi/aic7xxx/aic7xxx.seq b/drivers/scsi/aic7xxx/aic7xxx.seq new file mode 100644 index 000000000..e60041e8f --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx.seq @@ -0,0 +1,2399 @@ +/* + * Adaptec 274x/284x/294x device driver firmware for Linux and FreeBSD. + * + * Copyright (c) 1994-2001 Justin T. Gibbs. + * Copyright (c) 2000-2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $FreeBSD$ + */ + +VERSION = "$Id: //depot/aic7xxx/aic7xxx/aic7xxx.seq#58 $" +PATCH_ARG_LIST = "struct ahc_softc *ahc" +PREFIX = "ahc_" + +#include "aic7xxx.reg" +#include "scsi_message.h" + +/* + * A few words on the waiting SCB list: + * After starting the selection hardware, we check for reconnecting targets + * as well as for our selection to complete just in case the reselection wins + * bus arbitration. The problem with this is that we must keep track of the + * SCB that we've already pulled from the QINFIFO and started the selection + * on just in case the reselection wins so that we can retry the selection at + * a later time. This problem cannot be resolved by holding a single entry + * in scratch ram since a reconnecting target can request sense and this will + * create yet another SCB waiting for selection. The solution used here is to + * use byte 27 of the SCB as a pseudo-next pointer and to thread a list + * of SCBs that are awaiting selection. Since 0-0xfe are valid SCB indexes, + * SCB_LIST_NULL is 0xff which is out of range. An entry is also added to + * this list every time a request sense occurs or after completing a non-tagged + * command for which a second SCB has been queued. The sequencer will + * automatically consume the entries. + */ + +bus_free_sel: + /* + * Turn off the selection hardware. We need to reset the + * selection request in order to perform a new selection. + */ + and SCSISEQ, TEMODE|ENSELI|ENRSELI|ENAUTOATNP; + and SIMODE1, ~ENBUSFREE; +poll_for_work: + call clear_target_state; + and SXFRCTL0, ~SPIOEN; + if ((ahc->features & AHC_ULTRA2) != 0) { + clr SCSIBUSL; + } + test SCSISEQ, ENSELO jnz poll_for_selection; + if ((ahc->features & AHC_TWIN) != 0) { + xor SBLKCTL,SELBUSB; /* Toggle to the other bus */ + test SCSISEQ, ENSELO jnz poll_for_selection; + } + cmp WAITING_SCBH,SCB_LIST_NULL jne start_waiting; +poll_for_work_loop: + if ((ahc->features & AHC_TWIN) != 0) { + xor SBLKCTL,SELBUSB; /* Toggle to the other bus */ + } + test SSTAT0, SELDO|SELDI jnz selection; +test_queue: + /* Has the driver posted any work for us? */ +BEGIN_CRITICAL; + if ((ahc->features & AHC_QUEUE_REGS) != 0) { + test QOFF_CTLSTA, SCB_AVAIL jz poll_for_work_loop; + } else { + mov A, QINPOS; + cmp KERNEL_QINPOS, A je poll_for_work_loop; + } + mov ARG_1, NEXT_QUEUED_SCB; + + /* + * We have at least one queued SCB now and we don't have any + * SCBs in the list of SCBs awaiting selection. Allocate a + * card SCB for the host's SCB and get to work on it. + */ + if ((ahc->flags & AHC_PAGESCBS) != 0) { + mov ALLZEROS call get_free_or_disc_scb; + } else { + /* In the non-paging case, the SCBID == hardware SCB index */ + mov SCBPTR, ARG_1; + } + or SEQ_FLAGS2, SCB_DMA; +END_CRITICAL; +dma_queued_scb: + /* + * DMA the SCB from host ram into the current SCB location. + */ + mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET; + mov ARG_1 call dma_scb; + /* + * Check one last time to see if this SCB was canceled + * before we completed the DMA operation. If it was, + * the QINFIFO next pointer will not match our saved + * value. + */ + mov A, ARG_1; +BEGIN_CRITICAL; + cmp NEXT_QUEUED_SCB, A jne abort_qinscb; + if ((ahc->flags & AHC_SEQUENCER_DEBUG) != 0) { + cmp SCB_TAG, A je . + 2; + mvi SCB_MISMATCH call set_seqint; + } + mov NEXT_QUEUED_SCB, SCB_NEXT; + mov SCB_NEXT,WAITING_SCBH; + mov WAITING_SCBH, SCBPTR; + if ((ahc->features & AHC_QUEUE_REGS) != 0) { + mov NONE, SNSCB_QOFF; + } else { + inc QINPOS; + } + and SEQ_FLAGS2, ~SCB_DMA; +END_CRITICAL; +start_waiting: + /* + * Start the first entry on the waiting SCB list. + */ + mov SCBPTR, WAITING_SCBH; + call start_selection; + +poll_for_selection: + /* + * Twin channel devices cannot handle things like SELTO + * interrupts on the "background" channel. So, while + * selecting, keep polling the current channel until + * either a selection or reselection occurs. + */ + test SSTAT0, SELDO|SELDI jz poll_for_selection; + +selection: + /* + * We aren't expecting a bus free, so interrupt + * the kernel driver if it happens. + */ + mvi CLRSINT1,CLRBUSFREE; + if ((ahc->features & AHC_DT) == 0) { + or SIMODE1, ENBUSFREE; + } + + /* + * Guard against a bus free after (re)selection + * but prior to enabling the busfree interrupt. SELDI + * and SELDO will be cleared in that case. + */ + test SSTAT0, SELDI|SELDO jz bus_free_sel; + test SSTAT0,SELDO jnz select_out; +select_in: + if ((ahc->flags & AHC_TARGETROLE) != 0) { + if ((ahc->flags & AHC_INITIATORROLE) != 0) { + test SSTAT0, TARGET jz initiator_reselect; + } + mvi CLRSINT0, CLRSELDI; + + /* + * We've just been selected. Assert BSY and + * setup the phase for receiving messages + * from the target. + */ + mvi SCSISIGO, P_MESGOUT|BSYO; + + /* + * Setup the DMA for sending the identify and + * command information. + */ + mvi SEQ_FLAGS, CMDPHASE_PENDING; + + mov A, TQINPOS; + if ((ahc->features & AHC_CMD_CHAN) != 0) { + mvi DINDEX, CCHADDR; + mvi SHARED_DATA_ADDR call set_32byte_addr; + mvi CCSCBCTL, CCSCBRESET; + } else { + mvi DINDEX, HADDR; + mvi SHARED_DATA_ADDR call set_32byte_addr; + mvi DFCNTRL, FIFORESET; + } + + /* Initiator that selected us */ + and SAVED_SCSIID, SELID_MASK, SELID; + /* The Target ID we were selected at */ + if ((ahc->features & AHC_MULTI_TID) != 0) { + and A, OID, TARGIDIN; + } else if ((ahc->features & AHC_ULTRA2) != 0) { + and A, OID, SCSIID_ULTRA2; + } else { + and A, OID, SCSIID; + } + or SAVED_SCSIID, A; + if ((ahc->features & AHC_TWIN) != 0) { + test SBLKCTL, SELBUSB jz . + 2; + or SAVED_SCSIID, TWIN_CHNLB; + } + if ((ahc->features & AHC_CMD_CHAN) != 0) { + mov CCSCBRAM, SAVED_SCSIID; + } else { + mov DFDAT, SAVED_SCSIID; + } + + /* + * If ATN isn't asserted, the target isn't interested + * in talking to us. Go directly to bus free. + * XXX SCSI-1 may require us to assume lun 0 if + * ATN is false. + */ + test SCSISIGI, ATNI jz target_busfree; + + /* + * Watch ATN closely now as we pull in messages from the + * initiator. We follow the guidlines from section 6.5 + * of the SCSI-2 spec for what messages are allowed when. + */ + call target_inb; + + /* + * Our first message must be one of IDENTIFY, ABORT, or + * BUS_DEVICE_RESET. + */ + test DINDEX, MSG_IDENTIFYFLAG jz host_target_message_loop; + /* Store for host */ + if ((ahc->features & AHC_CMD_CHAN) != 0) { + mov CCSCBRAM, DINDEX; + } else { + mov DFDAT, DINDEX; + } + and SAVED_LUN, MSG_IDENTIFY_LUNMASK, DINDEX; + + /* Remember for disconnection decision */ + test DINDEX, MSG_IDENTIFY_DISCFLAG jnz . + 2; + /* XXX Honor per target settings too */ + or SEQ_FLAGS, NO_DISCONNECT; + + test SCSISIGI, ATNI jz ident_messages_done; + call target_inb; + /* + * If this is a tagged request, the tagged message must + * immediately follow the identify. We test for a valid + * tag message by seeing if it is >= MSG_SIMPLE_Q_TAG and + * < MSG_IGN_WIDE_RESIDUE. + */ + add A, -MSG_SIMPLE_Q_TAG, DINDEX; + jnc ident_messages_done_msg_pending; + add A, -MSG_IGN_WIDE_RESIDUE, DINDEX; + jc ident_messages_done_msg_pending; + + /* Store for host */ + if ((ahc->features & AHC_CMD_CHAN) != 0) { + mov CCSCBRAM, DINDEX; + } else { + mov DFDAT, DINDEX; + } + + /* + * If the initiator doesn't feel like providing a tag number, + * we've got a failed selection and must transition to bus + * free. + */ + test SCSISIGI, ATNI jz target_busfree; + + /* + * Store the tag for the host. + */ + call target_inb; + if ((ahc->features & AHC_CMD_CHAN) != 0) { + mov CCSCBRAM, DINDEX; + } else { + mov DFDAT, DINDEX; + } + mov INITIATOR_TAG, DINDEX; + or SEQ_FLAGS, TARGET_CMD_IS_TAGGED; + +ident_messages_done: + /* Terminate the ident list */ + if ((ahc->features & AHC_CMD_CHAN) != 0) { + mvi CCSCBRAM, SCB_LIST_NULL; + } else { + mvi DFDAT, SCB_LIST_NULL; + } + or SEQ_FLAGS, TARG_CMD_PENDING; + test SEQ_FLAGS2, TARGET_MSG_PENDING + jnz target_mesgout_pending; + test SCSISIGI, ATNI jnz target_mesgout_continue; + jmp target_ITloop; + + +ident_messages_done_msg_pending: + or SEQ_FLAGS2, TARGET_MSG_PENDING; + jmp ident_messages_done; + + /* + * Pushed message loop to allow the kernel to + * run it's own target mode message state engine. + */ +host_target_message_loop: + mvi HOST_MSG_LOOP call set_seqint; + cmp RETURN_1, EXIT_MSG_LOOP je target_ITloop; + test SSTAT0, SPIORDY jz .; + jmp host_target_message_loop; + } + +if ((ahc->flags & AHC_INITIATORROLE) != 0) { +/* + * Reselection has been initiated by a target. Make a note that we've been + * reselected, but haven't seen an IDENTIFY message from the target yet. + */ +initiator_reselect: + /* XXX test for and handle ONE BIT condition */ + or SXFRCTL0, SPIOEN|CLRSTCNT|CLRCHN; + and SAVED_SCSIID, SELID_MASK, SELID; + if ((ahc->features & AHC_ULTRA2) != 0) { + and A, OID, SCSIID_ULTRA2; + } else { + and A, OID, SCSIID; + } + or SAVED_SCSIID, A; + if ((ahc->features & AHC_TWIN) != 0) { + test SBLKCTL, SELBUSB jz . + 2; + or SAVED_SCSIID, TWIN_CHNLB; + } + mvi CLRSINT0, CLRSELDI; + jmp ITloop; +} + +abort_qinscb: + call add_scb_to_free_list; + jmp poll_for_work_loop; + +start_selection: + /* + * If bus reset interrupts have been disabled (from a previous + * reset), re-enable them now. Resets are only of interest + * when we have outstanding transactions, so we can safely + * defer re-enabling the interrupt until, as an initiator, + * we start sending out transactions again. + */ + test SIMODE1, ENSCSIRST jnz . + 3; + mvi CLRSINT1, CLRSCSIRSTI; + or SIMODE1, ENSCSIRST; + if ((ahc->features & AHC_TWIN) != 0) { + and SINDEX,~SELBUSB,SBLKCTL;/* Clear channel select bit */ + test SCB_SCSIID, TWIN_CHNLB jz . + 2; + or SINDEX, SELBUSB; + mov SBLKCTL,SINDEX; /* select channel */ + } +initialize_scsiid: + if ((ahc->features & AHC_ULTRA2) != 0) { + mov SCSIID_ULTRA2, SCB_SCSIID; + } else if ((ahc->features & AHC_TWIN) != 0) { + and SCSIID, TWIN_TID|OID, SCB_SCSIID; + } else { + mov SCSIID, SCB_SCSIID; + } + if ((ahc->flags & AHC_TARGETROLE) != 0) { + mov SINDEX, SCSISEQ_TEMPLATE; + test SCB_CONTROL, TARGET_SCB jz . + 2; + or SINDEX, TEMODE; + mov SCSISEQ, SINDEX ret; + } else { + mov SCSISEQ, SCSISEQ_TEMPLATE ret; + } + +/* + * Initialize transfer settings with SCB provided settings. + */ +set_transfer_settings: + if ((ahc->features & AHC_ULTRA) != 0) { + test SCB_CONTROL, ULTRAENB jz . + 2; + or SXFRCTL0, FAST20; + } + /* + * Initialize SCSIRATE with the appropriate value for this target. + */ + if ((ahc->features & AHC_ULTRA2) != 0) { + bmov SCSIRATE, SCB_SCSIRATE, 2 ret; + } else { + mov SCSIRATE, SCB_SCSIRATE ret; + } + +if ((ahc->flags & AHC_TARGETROLE) != 0) { +/* + * We carefully toggle SPIOEN to allow us to return the + * message byte we receive so it can be checked prior to + * driving REQ on the bus for the next byte. + */ +target_inb: + /* + * Drive REQ on the bus by enabling SCSI PIO. + */ + or SXFRCTL0, SPIOEN; + /* Wait for the byte */ + test SSTAT0, SPIORDY jz .; + /* Prevent our read from triggering another REQ */ + and SXFRCTL0, ~SPIOEN; + /* Save latched contents */ + mov DINDEX, SCSIDATL ret; +} + +/* + * After the selection, remove this SCB from the "waiting SCB" + * list. This is achieved by simply moving our "next" pointer into + * WAITING_SCBH. Our next pointer will be set to null the next time this + * SCB is used, so don't bother with it now. + */ +select_out: + /* Turn off the selection hardware */ + and SCSISEQ, TEMODE|ENSELI|ENRSELI|ENAUTOATNP, SCSISEQ; + mov SCBPTR, WAITING_SCBH; + mov WAITING_SCBH,SCB_NEXT; + mov SAVED_SCSIID, SCB_SCSIID; + and SAVED_LUN, LID, SCB_LUN; + call set_transfer_settings; + if ((ahc->flags & AHC_TARGETROLE) != 0) { + test SSTAT0, TARGET jz initiator_select; + + or SXFRCTL0, CLRSTCNT|CLRCHN; + + /* + * Put tag in connonical location since not + * all connections have an SCB. + */ + mov INITIATOR_TAG, SCB_TARGET_ITAG; + + /* + * We've just re-selected an initiator. + * Assert BSY and setup the phase for + * sending our identify messages. + */ + mvi P_MESGIN|BSYO call change_phase; + mvi CLRSINT0, CLRSELDO; + + /* + * Start out with a simple identify message. + */ + or SAVED_LUN, MSG_IDENTIFYFLAG call target_outb; + + /* + * If we are the result of a tagged command, send + * a simple Q tag and the tag id. + */ + test SCB_CONTROL, TAG_ENB jz . + 3; + mvi MSG_SIMPLE_Q_TAG call target_outb; + mov SCB_TARGET_ITAG call target_outb; +target_synccmd: + /* + * Now determine what phases the host wants us + * to go through. + */ + mov SEQ_FLAGS, SCB_TARGET_PHASES; + + test SCB_CONTROL, MK_MESSAGE jz target_ITloop; + mvi P_MESGIN|BSYO call change_phase; + jmp host_target_message_loop; +target_ITloop: + /* + * Start honoring ATN signals now that + * we properly identified ourselves. + */ + test SCSISIGI, ATNI jnz target_mesgout; + test SEQ_FLAGS, CMDPHASE_PENDING jnz target_cmdphase; + test SEQ_FLAGS, DPHASE_PENDING jnz target_dphase; + test SEQ_FLAGS, SPHASE_PENDING jnz target_sphase; + + /* + * No more work to do. Either disconnect or not depending + * on the state of NO_DISCONNECT. + */ + test SEQ_FLAGS, NO_DISCONNECT jz target_disconnect; + mvi TARG_IMMEDIATE_SCB, SCB_LIST_NULL; + call complete_target_cmd; + if ((ahc->flags & AHC_PAGESCBS) != 0) { + mov ALLZEROS call get_free_or_disc_scb; + } + cmp TARG_IMMEDIATE_SCB, SCB_LIST_NULL je .; + mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET; + mov TARG_IMMEDIATE_SCB call dma_scb; + call set_transfer_settings; + or SXFRCTL0, CLRSTCNT|CLRCHN; + jmp target_synccmd; + +target_mesgout: + mvi SCSISIGO, P_MESGOUT|BSYO; +target_mesgout_continue: + call target_inb; +target_mesgout_pending: + and SEQ_FLAGS2, ~TARGET_MSG_PENDING; + /* Local Processing goes here... */ + jmp host_target_message_loop; + +target_disconnect: + mvi P_MESGIN|BSYO call change_phase; + test SEQ_FLAGS, DPHASE jz . + 2; + mvi MSG_SAVEDATAPOINTER call target_outb; + mvi MSG_DISCONNECT call target_outb; + +target_busfree_wait: + /* Wait for preceding I/O session to complete. */ + test SCSISIGI, ACKI jnz .; +target_busfree: + and SIMODE1, ~ENBUSFREE; + if ((ahc->features & AHC_ULTRA2) != 0) { + clr SCSIBUSL; + } + clr SCSISIGO; + mvi LASTPHASE, P_BUSFREE; + call complete_target_cmd; + jmp poll_for_work; + +target_cmdphase: + /* + * The target has dropped ATN (doesn't want to abort or BDR) + * and we believe this selection to be valid. If the ring + * buffer for new commands is full, return busy or queue full. + */ + if ((ahc->features & AHC_HS_MAILBOX) != 0) { + and A, HOST_TQINPOS, HS_MAILBOX; + } else { + mov A, KERNEL_TQINPOS; + } + cmp TQINPOS, A jne tqinfifo_has_space; + mvi P_STATUS|BSYO call change_phase; + test SEQ_FLAGS, TARGET_CMD_IS_TAGGED jz . + 3; + mvi STATUS_QUEUE_FULL call target_outb; + jmp target_busfree_wait; + mvi STATUS_BUSY call target_outb; + jmp target_busfree_wait; +tqinfifo_has_space: + mvi P_COMMAND|BSYO call change_phase; + call target_inb; + mov A, DINDEX; + /* Store for host */ + if ((ahc->features & AHC_CMD_CHAN) != 0) { + mov CCSCBRAM, A; + } else { + mov DFDAT, A; + } + + /* + * Determine the number of bytes to read + * based on the command group code via table lookup. + * We reuse the first 8 bytes of the TARG_SCSIRATE + * BIOS array for this table. Count is one less than + * the total for the command since we've already fetched + * the first byte. + */ + shr A, CMD_GROUP_CODE_SHIFT; + add SINDEX, CMDSIZE_TABLE, A; + mov A, SINDIR; + + test A, 0xFF jz command_phase_done; + or SXFRCTL0, SPIOEN; +command_loop: + test SSTAT0, SPIORDY jz .; + cmp A, 1 jne . + 2; + and SXFRCTL0, ~SPIOEN; /* Last Byte */ + if ((ahc->features & AHC_CMD_CHAN) != 0) { + mov CCSCBRAM, SCSIDATL; + } else { + mov DFDAT, SCSIDATL; + } + dec A; + test A, 0xFF jnz command_loop; + +command_phase_done: + and SEQ_FLAGS, ~CMDPHASE_PENDING; + jmp target_ITloop; + +target_dphase: + /* + * Data phases on the bus are from the + * perspective of the initiator. The dma + * code looks at LASTPHASE to determine the + * data direction of the DMA. Toggle it for + * target transfers. + */ + xor LASTPHASE, IOI, SCB_TARGET_DATA_DIR; + or SCB_TARGET_DATA_DIR, BSYO call change_phase; + jmp p_data; + +target_sphase: + mvi P_STATUS|BSYO call change_phase; + mvi LASTPHASE, P_STATUS; + mov SCB_SCSI_STATUS call target_outb; + /* XXX Watch for ATN or parity errors??? */ + mvi SCSISIGO, P_MESGIN|BSYO; + /* MSG_CMDCMPLT is 0, but we can't do an immediate of 0 */ + mov ALLZEROS call target_outb; + jmp target_busfree_wait; + +complete_target_cmd: + test SEQ_FLAGS, TARG_CMD_PENDING jnz . + 2; + mov SCB_TAG jmp complete_post; + if ((ahc->features & AHC_CMD_CHAN) != 0) { + /* Set the valid byte */ + mvi CCSCBADDR, 24; + mov CCSCBRAM, ALLONES; + mvi CCHCNT, 28; + or CCSCBCTL, CCSCBEN|CCSCBRESET; + test CCSCBCTL, CCSCBDONE jz .; + clr CCSCBCTL; + } else { + /* Set the valid byte */ + or DFCNTRL, FIFORESET; + mvi DFWADDR, 3; /* Third 64bit word or byte 24 */ + mov DFDAT, ALLONES; + mvi 28 call set_hcnt; + or DFCNTRL, HDMAEN|FIFOFLUSH; + call dma_finish; + } + inc TQINPOS; + mvi INTSTAT,CMDCMPLT ret; + } + +if ((ahc->flags & AHC_INITIATORROLE) != 0) { +initiator_select: + or SXFRCTL0, SPIOEN|CLRSTCNT|CLRCHN; + /* + * As soon as we get a successful selection, the target + * should go into the message out phase since we have ATN + * asserted. + */ + mvi MSG_OUT, MSG_IDENTIFYFLAG; + mvi SEQ_FLAGS, NO_CDB_SENT; + mvi CLRSINT0, CLRSELDO; + + /* + * Main loop for information transfer phases. Wait for the + * target to assert REQ before checking MSG, C/D and I/O for + * the bus phase. + */ +mesgin_phasemis: +ITloop: + call phase_lock; + + mov A, LASTPHASE; + + test A, ~P_DATAIN jz p_data; + cmp A,P_COMMAND je p_command; + cmp A,P_MESGOUT je p_mesgout; + cmp A,P_STATUS je p_status; + cmp A,P_MESGIN je p_mesgin; + + mvi BAD_PHASE call set_seqint; + jmp ITloop; /* Try reading the bus again. */ + +await_busfree: + and SIMODE1, ~ENBUSFREE; + mov NONE, SCSIDATL; /* Ack the last byte */ + if ((ahc->features & AHC_ULTRA2) != 0) { + clr SCSIBUSL; /* Prevent bit leakage durint SELTO */ + } + and SXFRCTL0, ~SPIOEN; + mvi SEQ_FLAGS, NOT_IDENTIFIED|NO_CDB_SENT; + test SSTAT1,REQINIT|BUSFREE jz .; + test SSTAT1, BUSFREE jnz poll_for_work; + mvi MISSED_BUSFREE call set_seqint; +} + +clear_target_state: + /* + * We assume that the kernel driver may reset us + * at any time, even in the middle of a DMA, so + * clear DFCNTRL too. + */ + clr DFCNTRL; + or SXFRCTL0, CLRSTCNT|CLRCHN; + + /* + * We don't know the target we will connect to, + * so default to narrow transfers to avoid + * parity problems. + */ + if ((ahc->features & AHC_ULTRA2) != 0) { + bmov SCSIRATE, ALLZEROS, 2; + } else { + clr SCSIRATE; + if ((ahc->features & AHC_ULTRA) != 0) { + and SXFRCTL0, ~(FAST20); + } + } + mvi LASTPHASE, P_BUSFREE; + /* clear target specific flags */ + mvi SEQ_FLAGS, NOT_IDENTIFIED|NO_CDB_SENT ret; + +sg_advance: + clr A; /* add sizeof(struct scatter) */ + add SCB_RESIDUAL_SGPTR[0],SG_SIZEOF; + adc SCB_RESIDUAL_SGPTR[1],A; + adc SCB_RESIDUAL_SGPTR[2],A; + adc SCB_RESIDUAL_SGPTR[3],A ret; + +if ((ahc->features & AHC_CMD_CHAN) != 0) { +disable_ccsgen: + test CCSGCTL, CCSGEN jz return; + test CCSGCTL, CCSGDONE jz .; +disable_ccsgen_fetch_done: + clr CCSGCTL; + test CCSGCTL, CCSGEN jnz .; + ret; +idle_loop: + /* + * Do we need any more segments for this transfer? + */ + test SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG jnz return; + + /* Did we just finish fetching segs? */ + cmp CCSGCTL, CCSGEN|CCSGDONE je idle_sgfetch_complete; + + /* Are we actively fetching segments? */ + test CCSGCTL, CCSGEN jnz return; + + /* + * Do we have any prefetch left??? + */ + cmp CCSGADDR, SG_PREFETCH_CNT jne idle_sg_avail; + + /* + * Need to fetch segments, but we can only do that + * if the command channel is completely idle. Make + * sure we don't have an SCB prefetch going on. + */ + test CCSCBCTL, CCSCBEN jnz return; + + /* + * We fetch a "cacheline aligned" and sized amount of data + * so we don't end up referencing a non-existent page. + * Cacheline aligned is in quotes because the kernel will + * set the prefetch amount to a reasonable level if the + * cacheline size is unknown. + */ + mvi CCHCNT, SG_PREFETCH_CNT; + and CCHADDR[0], SG_PREFETCH_ALIGN_MASK, SCB_RESIDUAL_SGPTR; + bmov CCHADDR[1], SCB_RESIDUAL_SGPTR[1], 3; + mvi CCSGCTL, CCSGEN|CCSGRESET ret; +idle_sgfetch_complete: + call disable_ccsgen_fetch_done; + and CCSGADDR, SG_PREFETCH_ADDR_MASK, SCB_RESIDUAL_SGPTR; +idle_sg_avail: + if ((ahc->features & AHC_ULTRA2) != 0) { + /* Does the hardware have space for another SG entry? */ + test DFSTATUS, PRELOAD_AVAIL jz return; + bmov HADDR, CCSGRAM, 7; + bmov SCB_RESIDUAL_DATACNT[3], CCSGRAM, 1; + if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) { + mov SCB_RESIDUAL_DATACNT[3] call set_hhaddr; + } + call sg_advance; + mov SINDEX, SCB_RESIDUAL_SGPTR[0]; + test SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG jz . + 2; + or SINDEX, LAST_SEG; + mov SG_CACHE_PRE, SINDEX; + /* Load the segment */ + or DFCNTRL, PRELOADEN; + } + ret; +} + +if ((ahc->bugs & AHC_PCI_MWI_BUG) != 0 && ahc->pci_cachesize != 0) { +/* + * Calculate the trailing portion of this S/G segment that cannot + * be transferred using memory write and invalidate PCI transactions. + * XXX Can we optimize this for PCI writes only??? + */ +calc_mwi_residual: + /* + * If the ending address is on a cacheline boundary, + * there is no need for an extra segment. + */ + mov A, HCNT[0]; + add A, A, HADDR[0]; + and A, CACHESIZE_MASK; + test A, 0xFF jz return; + + /* + * If the transfer is less than a cachline, + * there is no need for an extra segment. + */ + test HCNT[1], 0xFF jnz calc_mwi_residual_final; + test HCNT[2], 0xFF jnz calc_mwi_residual_final; + add NONE, INVERTED_CACHESIZE_MASK, HCNT[0]; + jnc return; + +calc_mwi_residual_final: + mov MWI_RESIDUAL, A; + not A; + inc A; + add HCNT[0], A; + adc HCNT[1], -1; + adc HCNT[2], -1 ret; +} + +p_data: + test SEQ_FLAGS,NOT_IDENTIFIED|NO_CDB_SENT jz p_data_allowed; + mvi PROTO_VIOLATION call set_seqint; +p_data_allowed: + if ((ahc->features & AHC_ULTRA2) != 0) { + mvi DMAPARAMS, PRELOADEN|SCSIEN|HDMAEN; + } else { + mvi DMAPARAMS, WIDEODD|SCSIEN|SDMAEN|HDMAEN|FIFORESET; + } + test LASTPHASE, IOI jnz . + 2; + or DMAPARAMS, DIRECTION; + if ((ahc->features & AHC_CMD_CHAN) != 0) { + /* We don't have any valid S/G elements */ + mvi CCSGADDR, SG_PREFETCH_CNT; + } + test SEQ_FLAGS, DPHASE jz data_phase_initialize; + + /* + * If we re-enter the data phase after going through another + * phase, our transfer location has almost certainly been + * corrupted by the interveining, non-data, transfers. Ask + * the host driver to fix us up based on the transfer residual. + */ + mvi PDATA_REINIT call set_seqint; + jmp data_phase_loop; + +data_phase_initialize: + /* We have seen a data phase for the first time */ + or SEQ_FLAGS, DPHASE; + + /* + * Initialize the DMA address and counter from the SCB. + * Also set SCB_RESIDUAL_SGPTR, including the LAST_SEG + * flag in the highest byte of the data count. We cannot + * modify the saved values in the SCB until we see a save + * data pointers message. + */ + if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) { + /* The lowest address byte must be loaded last. */ + mov SCB_DATACNT[3] call set_hhaddr; + } + if ((ahc->features & AHC_CMD_CHAN) != 0) { + bmov HADDR, SCB_DATAPTR, 7; + bmov SCB_RESIDUAL_DATACNT[3], SCB_DATACNT[3], 5; + } else { + mvi DINDEX, HADDR; + mvi SCB_DATAPTR call bcopy_7; + mvi DINDEX, SCB_RESIDUAL_DATACNT + 3; + mvi SCB_DATACNT + 3 call bcopy_5; + } + if ((ahc->bugs & AHC_PCI_MWI_BUG) != 0 && ahc->pci_cachesize != 0) { + call calc_mwi_residual; + } + and SCB_RESIDUAL_SGPTR[0], ~SG_FULL_RESID; + + if ((ahc->features & AHC_ULTRA2) == 0) { + if ((ahc->features & AHC_CMD_CHAN) != 0) { + bmov STCNT, HCNT, 3; + } else { + call set_stcnt_from_hcnt; + } + } + +data_phase_loop: + /* Guard against overruns */ + test SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL jz data_phase_inbounds; + + /* + * Turn on `Bit Bucket' mode, wait until the target takes + * us to another phase, and then notify the host. + */ + and DMAPARAMS, DIRECTION; + mov DFCNTRL, DMAPARAMS; + or SXFRCTL1,BITBUCKET; + if ((ahc->features & AHC_DT) == 0) { + test SSTAT1,PHASEMIS jz .; + } else { + test SCSIPHASE, DATA_PHASE_MASK jnz .; + } + and SXFRCTL1, ~BITBUCKET; + mvi DATA_OVERRUN call set_seqint; + jmp ITloop; + +data_phase_inbounds: + if ((ahc->features & AHC_ULTRA2) != 0) { + mov SINDEX, SCB_RESIDUAL_SGPTR[0]; + test SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG jz . + 2; + or SINDEX, LAST_SEG; + mov SG_CACHE_PRE, SINDEX; + mov DFCNTRL, DMAPARAMS; +ultra2_dma_loop: + call idle_loop; + /* + * The transfer is complete if either the last segment + * completes or the target changes phase. + */ + test SG_CACHE_SHADOW, LAST_SEG_DONE jnz ultra2_dmafinish; + if ((ahc->features & AHC_DT) == 0) { + if ((ahc->flags & AHC_TARGETROLE) != 0) { + /* + * As a target, we control the phases, + * so ignore PHASEMIS. + */ + test SSTAT0, TARGET jnz ultra2_dma_loop; + } + if ((ahc->flags & AHC_INITIATORROLE) != 0) { + test SSTAT1,PHASEMIS jz ultra2_dma_loop; + } + } else { + test DFCNTRL, SCSIEN jnz ultra2_dma_loop; + } + +ultra2_dmafinish: + /* + * The transfer has terminated either due to a phase + * change, and/or the completion of the last segment. + * We have two goals here. Do as much other work + * as possible while the data fifo drains on a read + * and respond as quickly as possible to the standard + * messages (save data pointers/disconnect and command + * complete) that usually follow a data phase. + */ + if ((ahc->bugs & AHC_AUTOFLUSH_BUG) != 0) { + /* + * On chips with broken auto-flush, start + * the flushing process now. We'll poke + * the chip from time to time to keep the + * flush process going as we complete the + * data phase. + */ + or DFCNTRL, FIFOFLUSH; + } + /* + * We assume that, even though data may still be + * transferring to the host, that the SCSI side of + * the DMA engine is now in a static state. This + * allows us to update our notion of where we are + * in this transfer. + * + * If, by chance, we stopped before being able + * to fetch additional segments for this transfer, + * yet the last S/G was completely exhausted, + * call our idle loop until it is able to load + * another segment. This will allow us to immediately + * pickup on the next segment on the next data phase. + * + * If we happened to stop on the last segment, then + * our residual information is still correct from + * the idle loop and there is no need to perform + * any fixups. + */ +ultra2_ensure_sg: + test SG_CACHE_SHADOW, LAST_SEG jz ultra2_shvalid; + /* Record if we've consumed all S/G entries */ + test SSTAT2, SHVALID jnz residuals_correct; + or SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL; + jmp residuals_correct; + +ultra2_shvalid: + test SSTAT2, SHVALID jnz sgptr_fixup; + call idle_loop; + jmp ultra2_ensure_sg; + +sgptr_fixup: + /* + * Fixup the residual next S/G pointer. The S/G preload + * feature of the chip allows us to load two elements + * in addition to the currently active element. We + * store the bottom byte of the next S/G pointer in + * the SG_CACEPTR register so we can restore the + * correct value when the DMA completes. If the next + * sg ptr value has advanced to the point where higher + * bytes in the address have been affected, fix them + * too. + */ + test SG_CACHE_SHADOW, 0x80 jz sgptr_fixup_done; + test SCB_RESIDUAL_SGPTR[0], 0x80 jnz sgptr_fixup_done; + add SCB_RESIDUAL_SGPTR[1], -1; + adc SCB_RESIDUAL_SGPTR[2], -1; + adc SCB_RESIDUAL_SGPTR[3], -1; +sgptr_fixup_done: + and SCB_RESIDUAL_SGPTR[0], SG_ADDR_MASK, SG_CACHE_SHADOW; + /* We are not the last seg */ + and SCB_RESIDUAL_DATACNT[3], ~SG_LAST_SEG; +residuals_correct: + /* + * Go ahead and shut down the DMA engine now. + * In the future, we'll want to handle end of + * transfer messages prior to doing this, but this + * requires similar restructuring for pre-ULTRA2 + * controllers. + */ + test DMAPARAMS, DIRECTION jnz ultra2_fifoempty; +ultra2_fifoflush: + if ((ahc->features & AHC_DT) == 0) { + if ((ahc->bugs & AHC_AUTOFLUSH_BUG) != 0) { + /* + * On Rev A of the aic7890, the autoflush + * feature doesn't function correctly. + * Perform an explicit manual flush. During + * a manual flush, the FIFOEMP bit becomes + * true every time the PCI FIFO empties + * regardless of the state of the SCSI FIFO. + * It can take up to 4 clock cycles for the + * SCSI FIFO to get data into the PCI FIFO + * and for FIFOEMP to de-assert. Here we + * guard against this condition by making + * sure the FIFOEMP bit stays on for 5 full + * clock cycles. + */ + or DFCNTRL, FIFOFLUSH; + test DFSTATUS, FIFOEMP jz ultra2_fifoflush; + test DFSTATUS, FIFOEMP jz ultra2_fifoflush; + test DFSTATUS, FIFOEMP jz ultra2_fifoflush; + test DFSTATUS, FIFOEMP jz ultra2_fifoflush; + } + test DFSTATUS, FIFOEMP jz ultra2_fifoflush; + } else { + /* + * We enable the auto-ack feature on DT capable + * controllers. This means that the controller may + * have already transferred some overrun bytes into + * the data FIFO and acked them on the bus. The only + * way to detect this situation is to wait for + * LAST_SEG_DONE to come true on a completed transfer + * and then test to see if the data FIFO is non-empty. + */ + test SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL + jz ultra2_wait_fifoemp; + test SG_CACHE_SHADOW, LAST_SEG_DONE jz .; + /* + * FIFOEMP can lag LAST_SEG_DONE. Wait a few + * clocks before calling this an overrun. + */ + test DFSTATUS, FIFOEMP jnz ultra2_fifoempty; + test DFSTATUS, FIFOEMP jnz ultra2_fifoempty; + test DFSTATUS, FIFOEMP jnz ultra2_fifoempty; + /* Overrun */ + jmp data_phase_loop; +ultra2_wait_fifoemp: + test DFSTATUS, FIFOEMP jz .; + } +ultra2_fifoempty: + /* Don't clobber an inprogress host data transfer */ + test DFSTATUS, MREQPEND jnz ultra2_fifoempty; +ultra2_dmahalt: + and DFCNTRL, ~(SCSIEN|HDMAEN); + test DFCNTRL, SCSIEN|HDMAEN jnz .; + if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) { + /* + * Keep HHADDR cleared for future, 32bit addressed + * only, DMA operations. + * + * Due to bayonette style S/G handling, our residual + * data must be "fixed up" once the transfer is halted. + * Here we fixup the HSHADDR stored in the high byte + * of the residual data cnt. By postponing the fixup, + * we can batch the clearing of HADDR with the fixup. + * If we halted on the last segment, the residual is + * already correct. If we are not on the last + * segment, copy the high address directly from HSHADDR. + * We don't need to worry about maintaining the + * SG_LAST_SEG flag as it will always be false in the + * case where an update is required. + */ + or DSCOMMAND1, HADDLDSEL0; + test SG_CACHE_SHADOW, LAST_SEG jnz . + 2; + mov SCB_RESIDUAL_DATACNT[3], SHADDR; + clr HADDR; + and DSCOMMAND1, ~HADDLDSEL0; + } + } else { + /* If we are the last SG block, tell the hardware. */ + if ((ahc->bugs & AHC_PCI_MWI_BUG) != 0 + && ahc->pci_cachesize != 0) { + test MWI_RESIDUAL, 0xFF jnz dma_mid_sg; + } + test SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG jz dma_mid_sg; + if ((ahc->flags & AHC_TARGETROLE) != 0) { + test SSTAT0, TARGET jz dma_last_sg; + if ((ahc->bugs & AHC_TMODE_WIDEODD_BUG) != 0) { + test DMAPARAMS, DIRECTION jz dma_mid_sg; + } + } +dma_last_sg: + and DMAPARAMS, ~WIDEODD; +dma_mid_sg: + /* Start DMA data transfer. */ + mov DFCNTRL, DMAPARAMS; +dma_loop: + if ((ahc->features & AHC_CMD_CHAN) != 0) { + call idle_loop; + } + test SSTAT0,DMADONE jnz dma_dmadone; + test SSTAT1,PHASEMIS jz dma_loop; /* ie. underrun */ +dma_phasemis: + /* + * We will be "done" DMAing when the transfer count goes to + * zero, or the target changes the phase (in light of this, + * it makes sense that the DMA circuitry doesn't ACK when + * PHASEMIS is active). If we are doing a SCSI->Host transfer, + * the data FIFO should be flushed auto-magically on STCNT=0 + * or a phase change, so just wait for FIFO empty status. + */ +dma_checkfifo: + test DFCNTRL,DIRECTION jnz dma_fifoempty; +dma_fifoflush: + test DFSTATUS,FIFOEMP jz dma_fifoflush; +dma_fifoempty: + /* Don't clobber an inprogress host data transfer */ + test DFSTATUS, MREQPEND jnz dma_fifoempty; + + /* + * Now shut off the DMA and make sure that the DMA + * hardware has actually stopped. Touching the DMA + * counters, etc. while a DMA is active will result + * in an ILLSADDR exception. + */ +dma_dmadone: + and DFCNTRL, ~(SCSIEN|SDMAEN|HDMAEN); +dma_halt: + /* + * Some revisions of the aic78XX have a problem where, if the + * data fifo is full, but the PCI input latch is not empty, + * HDMAEN cannot be cleared. The fix used here is to drain + * the prefetched but unused data from the data fifo until + * there is space for the input latch to drain. + */ + if ((ahc->bugs & AHC_PCI_2_1_RETRY_BUG) != 0) { + mov NONE, DFDAT; + } + test DFCNTRL, (SCSIEN|SDMAEN|HDMAEN) jnz dma_halt; + + /* See if we have completed this last segment */ + test STCNT[0], 0xff jnz data_phase_finish; + test STCNT[1], 0xff jnz data_phase_finish; + test STCNT[2], 0xff jnz data_phase_finish; + + /* + * Advance the scatter-gather pointers if needed + */ + if ((ahc->bugs & AHC_PCI_MWI_BUG) != 0 + && ahc->pci_cachesize != 0) { + test MWI_RESIDUAL, 0xFF jz no_mwi_resid; + /* + * Reload HADDR from SHADDR and setup the + * count to be the size of our residual. + */ + if ((ahc->features & AHC_CMD_CHAN) != 0) { + bmov HADDR, SHADDR, 4; + mov HCNT, MWI_RESIDUAL; + bmov HCNT[1], ALLZEROS, 2; + } else { + mvi DINDEX, HADDR; + mvi SHADDR call bcopy_4; + mov MWI_RESIDUAL call set_hcnt; + } + clr MWI_RESIDUAL; + jmp sg_load_done; +no_mwi_resid: + } + test SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG jz sg_load; + or SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL; + jmp data_phase_finish; +sg_load: + /* + * Load the next SG element's data address and length + * into the DMA engine. If we don't have hardware + * to perform a prefetch, we'll have to fetch the + * segment from host memory first. + */ + if ((ahc->features & AHC_CMD_CHAN) != 0) { + /* Wait for the idle loop to complete */ + test CCSGCTL, CCSGEN jz . + 3; + call idle_loop; + test CCSGCTL, CCSGEN jnz . - 1; + bmov HADDR, CCSGRAM, 7; + /* + * Workaround for flaky external SCB RAM + * on certain aic7895 setups. It seems + * unable to handle direct transfers from + * S/G ram to certain SCB locations. + */ + mov SINDEX, CCSGRAM; + mov SCB_RESIDUAL_DATACNT[3], SINDEX; + } else { + if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) { + mov ALLZEROS call set_hhaddr; + } + mvi DINDEX, HADDR; + mvi SCB_RESIDUAL_SGPTR call bcopy_4; + + mvi SG_SIZEOF call set_hcnt; + + or DFCNTRL, HDMAEN|DIRECTION|FIFORESET; + + call dma_finish; + + mvi DINDEX, HADDR; + call dfdat_in_7; + mov SCB_RESIDUAL_DATACNT[3], DFDAT; + } + + if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) { + mov SCB_RESIDUAL_DATACNT[3] call set_hhaddr; + + /* + * The lowest address byte must be loaded + * last as it triggers the computation of + * some items in the PCI block. The ULTRA2 + * chips do this on PRELOAD. + */ + mov HADDR, HADDR; + } + if ((ahc->bugs & AHC_PCI_MWI_BUG) != 0 + && ahc->pci_cachesize != 0) { + call calc_mwi_residual; + } + + /* Point to the new next sg in memory */ + call sg_advance; + +sg_load_done: + if ((ahc->features & AHC_CMD_CHAN) != 0) { + bmov STCNT, HCNT, 3; + } else { + call set_stcnt_from_hcnt; + } + + if ((ahc->flags & AHC_TARGETROLE) != 0) { + test SSTAT0, TARGET jnz data_phase_loop; + } + } +data_phase_finish: + /* + * If the target has left us in data phase, loop through + * the dma code again. In the case of ULTRA2 adapters, + * we should only loop if there is a data overrun. For + * all other adapters, we'll loop after each S/G element + * is loaded as well as if there is an overrun. + */ + if ((ahc->flags & AHC_TARGETROLE) != 0) { + test SSTAT0, TARGET jnz data_phase_done; + } + if ((ahc->flags & AHC_INITIATORROLE) != 0) { + test SSTAT1, REQINIT jz .; + if ((ahc->features & AHC_DT) == 0) { + test SSTAT1,PHASEMIS jz data_phase_loop; + } else { + test SCSIPHASE, DATA_PHASE_MASK jnz data_phase_loop; + } + } + +data_phase_done: + /* + * After a DMA finishes, save the SG and STCNT residuals back into + * the SCB. We use STCNT instead of HCNT, since it's a reflection + * of how many bytes were transferred on the SCSI (as opposed to the + * host) bus. + */ + if ((ahc->features & AHC_CMD_CHAN) != 0) { + /* Kill off any pending prefetch */ + call disable_ccsgen; + } + + if ((ahc->features & AHC_ULTRA2) == 0) { + /* + * Clear the high address byte so that all other DMA + * operations, which use 32bit addressing, can assume + * HHADDR is 0. + */ + if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) { + mov ALLZEROS call set_hhaddr; + } + } + + /* + * Update our residual information before the information is + * lost by some other type of SCSI I/O (e.g. PIO). If we have + * transferred all data, no update is needed. + * + */ + test SCB_RESIDUAL_SGPTR, SG_LIST_NULL jnz residual_update_done; + if ((ahc->bugs & AHC_PCI_MWI_BUG) != 0 + && ahc->pci_cachesize != 0) { + if ((ahc->features & AHC_CMD_CHAN) != 0) { + test MWI_RESIDUAL, 0xFF jz bmov_resid; + } + mov A, MWI_RESIDUAL; + add SCB_RESIDUAL_DATACNT[0], A, STCNT[0]; + clr A; + adc SCB_RESIDUAL_DATACNT[1], A, STCNT[1]; + adc SCB_RESIDUAL_DATACNT[2], A, STCNT[2]; + clr MWI_RESIDUAL; + if ((ahc->features & AHC_CMD_CHAN) != 0) { + jmp . + 2; +bmov_resid: + bmov SCB_RESIDUAL_DATACNT, STCNT, 3; + } + } else if ((ahc->features & AHC_CMD_CHAN) != 0) { + bmov SCB_RESIDUAL_DATACNT, STCNT, 3; + } else { + mov SCB_RESIDUAL_DATACNT[0], STCNT[0]; + mov SCB_RESIDUAL_DATACNT[1], STCNT[1]; + mov SCB_RESIDUAL_DATACNT[2], STCNT[2]; + } +residual_update_done: + /* + * Since we've been through a data phase, the SCB_RESID* fields + * are now initialized. Clear the full residual flag. + */ + and SCB_SGPTR[0], ~SG_FULL_RESID; + + if ((ahc->features & AHC_ULTRA2) != 0) { + /* Clear the channel in case we return to data phase later */ + or SXFRCTL0, CLRSTCNT|CLRCHN; + or SXFRCTL0, CLRSTCNT|CLRCHN; + } + + if ((ahc->flags & AHC_TARGETROLE) != 0) { + test SEQ_FLAGS, DPHASE_PENDING jz ITloop; + and SEQ_FLAGS, ~DPHASE_PENDING; + /* + * For data-in phases, wait for any pending acks from the + * initiator before changing phase. We only need to + * send Ignore Wide Residue messages for data-in phases. + */ + test DFCNTRL, DIRECTION jz target_ITloop; + test SSTAT1, REQINIT jnz .; + test SCB_LUN, SCB_XFERLEN_ODD jz target_ITloop; + test SCSIRATE, WIDEXFER jz target_ITloop; + /* + * Issue an Ignore Wide Residue Message. + */ + mvi P_MESGIN|BSYO call change_phase; + mvi MSG_IGN_WIDE_RESIDUE call target_outb; + mvi 1 call target_outb; + jmp target_ITloop; + } else { + jmp ITloop; + } + +if ((ahc->flags & AHC_INITIATORROLE) != 0) { +/* + * Command phase. Set up the DMA registers and let 'er rip. + */ +p_command: + test SEQ_FLAGS, NOT_IDENTIFIED jz p_command_okay; + mvi PROTO_VIOLATION call set_seqint; +p_command_okay: + + if ((ahc->features & AHC_ULTRA2) != 0) { + bmov HCNT[0], SCB_CDB_LEN, 1; + bmov HCNT[1], ALLZEROS, 2; + mvi SG_CACHE_PRE, LAST_SEG; + } else if ((ahc->features & AHC_CMD_CHAN) != 0) { + bmov STCNT[0], SCB_CDB_LEN, 1; + bmov STCNT[1], ALLZEROS, 2; + } else { + mov STCNT[0], SCB_CDB_LEN; + clr STCNT[1]; + clr STCNT[2]; + } + add NONE, -13, SCB_CDB_LEN; + mvi SCB_CDB_STORE jnc p_command_embedded; +p_command_from_host: + if ((ahc->features & AHC_ULTRA2) != 0) { + bmov HADDR[0], SCB_CDB_PTR, 4; + mvi DFCNTRL, (PRELOADEN|SCSIEN|HDMAEN|DIRECTION); + } else { + if ((ahc->features & AHC_CMD_CHAN) != 0) { + bmov HADDR[0], SCB_CDB_PTR, 4; + bmov HCNT, STCNT, 3; + } else { + mvi DINDEX, HADDR; + mvi SCB_CDB_PTR call bcopy_4; + mov SCB_CDB_LEN call set_hcnt; + } + mvi DFCNTRL, (SCSIEN|SDMAEN|HDMAEN|DIRECTION|FIFORESET); + } + jmp p_command_xfer; +p_command_embedded: + /* + * The data fifo seems to require 4 byte aligned + * transfers from the sequencer. Force this to + * be the case by clearing HADDR[0] even though + * we aren't going to touch host memory. + */ + clr HADDR[0]; + if ((ahc->features & AHC_ULTRA2) != 0) { + mvi DFCNTRL, (PRELOADEN|SCSIEN|DIRECTION); + bmov DFDAT, SCB_CDB_STORE, 12; + } else if ((ahc->features & AHC_CMD_CHAN) != 0) { + if ((ahc->flags & AHC_SCB_BTT) != 0) { + /* + * On the 7895 the data FIFO will + * get corrupted if you try to dump + * data from external SCB memory into + * the FIFO while it is enabled. So, + * fill the fifo and then enable SCSI + * transfers. + */ + mvi DFCNTRL, (DIRECTION|FIFORESET); + } else { + mvi DFCNTRL, (SCSIEN|SDMAEN|DIRECTION|FIFORESET); + } + bmov DFDAT, SCB_CDB_STORE, 12; + if ((ahc->flags & AHC_SCB_BTT) != 0) { + mvi DFCNTRL, (SCSIEN|SDMAEN|DIRECTION|FIFOFLUSH); + } else { + or DFCNTRL, FIFOFLUSH; + } + } else { + mvi DFCNTRL, (SCSIEN|SDMAEN|DIRECTION|FIFORESET); + call copy_to_fifo_6; + call copy_to_fifo_6; + or DFCNTRL, FIFOFLUSH; + } +p_command_xfer: + and SEQ_FLAGS, ~NO_CDB_SENT; + if ((ahc->features & AHC_DT) == 0) { + test SSTAT0, SDONE jnz . + 2; + test SSTAT1, PHASEMIS jz . - 1; + /* + * Wait for our ACK to go-away on it's own + * instead of being killed by SCSIEN getting cleared. + */ + test SCSISIGI, ACKI jnz .; + } else { + test DFCNTRL, SCSIEN jnz .; + } + test SSTAT0, SDONE jnz p_command_successful; + /* + * Don't allow a data phase if the command + * was not fully transferred. + */ + or SEQ_FLAGS, NO_CDB_SENT; +p_command_successful: + and DFCNTRL, ~(SCSIEN|SDMAEN|HDMAEN); + test DFCNTRL, (SCSIEN|SDMAEN|HDMAEN) jnz .; + jmp ITloop; + +/* + * Status phase. Wait for the data byte to appear, then read it + * and store it into the SCB. + */ +p_status: + test SEQ_FLAGS, NOT_IDENTIFIED jnz mesgin_proto_violation; +p_status_okay: + mov SCB_SCSI_STATUS, SCSIDATL; + or SCB_CONTROL, STATUS_RCVD; + jmp ITloop; + +/* + * Message out phase. If MSG_OUT is MSG_IDENTIFYFLAG, build a full + * indentify message sequence and send it to the target. The host may + * override this behavior by setting the MK_MESSAGE bit in the SCB + * control byte. This will cause us to interrupt the host and allow + * it to handle the message phase completely on its own. If the bit + * associated with this target is set, we will also interrupt the host, + * thereby allowing it to send a message on the next selection regardless + * of the transaction being sent. + * + * If MSG_OUT is == HOST_MSG, also interrupt the host and take a message. + * This is done to allow the host to send messages outside of an identify + * sequence while protecting the seqencer from testing the MK_MESSAGE bit + * on an SCB that might not be for the current nexus. (For example, a + * BDR message in response to a bad reselection would leave us pointed to + * an SCB that doesn't have anything to do with the current target). + * + * Otherwise, treat MSG_OUT as a 1 byte message to send (abort, abort tag, + * bus device reset). + * + * When there are no messages to send, MSG_OUT should be set to MSG_NOOP, + * in case the target decides to put us in this phase for some strange + * reason. + */ +p_mesgout_retry: + /* Turn on ATN for the retry */ + if ((ahc->features & AHC_DT) == 0) { + or SCSISIGO, ATNO, LASTPHASE; + } else { + mvi SCSISIGO, ATNO; + } +p_mesgout: + mov SINDEX, MSG_OUT; + cmp SINDEX, MSG_IDENTIFYFLAG jne p_mesgout_from_host; + test SCB_CONTROL,MK_MESSAGE jnz host_message_loop; +p_mesgout_identify: + or SINDEX, MSG_IDENTIFYFLAG|DISCENB, SAVED_LUN; + test SCB_CONTROL, DISCENB jnz . + 2; + and SINDEX, ~DISCENB; +/* + * Send a tag message if TAG_ENB is set in the SCB control block. + * Use SCB_TAG (the position in the kernel's SCB array) as the tag value. + */ +p_mesgout_tag: + test SCB_CONTROL,TAG_ENB jz p_mesgout_onebyte; + mov SCSIDATL, SINDEX; /* Send the identify message */ + call phase_lock; + cmp LASTPHASE, P_MESGOUT jne p_mesgout_done; + and SCSIDATL,TAG_ENB|SCB_TAG_TYPE,SCB_CONTROL; + call phase_lock; + cmp LASTPHASE, P_MESGOUT jne p_mesgout_done; + mov SCB_TAG jmp p_mesgout_onebyte; +/* + * Interrupt the driver, and allow it to handle this message + * phase and any required retries. + */ +p_mesgout_from_host: + cmp SINDEX, HOST_MSG jne p_mesgout_onebyte; + jmp host_message_loop; + +p_mesgout_onebyte: + mvi CLRSINT1, CLRATNO; + mov SCSIDATL, SINDEX; + +/* + * If the next bus phase after ATN drops is message out, it means + * that the target is requesting that the last message(s) be resent. + */ + call phase_lock; + cmp LASTPHASE, P_MESGOUT je p_mesgout_retry; + +p_mesgout_done: + mvi CLRSINT1,CLRATNO; /* Be sure to turn ATNO off */ + mov LAST_MSG, MSG_OUT; + mvi MSG_OUT, MSG_NOOP; /* No message left */ + jmp ITloop; + +/* + * Message in phase. Bytes are read using Automatic PIO mode. + */ +p_mesgin: + mvi ACCUM call inb_first; /* read the 1st message byte */ + + test A,MSG_IDENTIFYFLAG jnz mesgin_identify; + cmp A,MSG_DISCONNECT je mesgin_disconnect; + cmp A,MSG_SAVEDATAPOINTER je mesgin_sdptrs; + cmp ALLZEROS,A je mesgin_complete; + cmp A,MSG_RESTOREPOINTERS je mesgin_rdptrs; + cmp A,MSG_IGN_WIDE_RESIDUE je mesgin_ign_wide_residue; + cmp A,MSG_NOOP je mesgin_done; + +/* + * Pushed message loop to allow the kernel to + * run it's own message state engine. To avoid an + * extra nop instruction after signaling the kernel, + * we perform the phase_lock before checking to see + * if we should exit the loop and skip the phase_lock + * in the ITloop. Performing back to back phase_locks + * shouldn't hurt, but why do it twice... + */ +host_message_loop: + mvi HOST_MSG_LOOP call set_seqint; + call phase_lock; + cmp RETURN_1, EXIT_MSG_LOOP je ITloop + 1; + jmp host_message_loop; + +mesgin_ign_wide_residue: +if ((ahc->features & AHC_WIDE) != 0) { + test SCSIRATE, WIDEXFER jz mesgin_reject; + /* Pull the residue byte */ + mvi ARG_1 call inb_next; + cmp ARG_1, 0x01 jne mesgin_reject; + test SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL jz . + 2; + test SCB_LUN, SCB_XFERLEN_ODD jnz mesgin_done; + mvi IGN_WIDE_RES call set_seqint; + jmp mesgin_done; +} + +mesgin_proto_violation: + mvi PROTO_VIOLATION call set_seqint; + jmp mesgin_done; +mesgin_reject: + mvi MSG_MESSAGE_REJECT call mk_mesg; +mesgin_done: + mov NONE,SCSIDATL; /*dummy read from latch to ACK*/ + jmp ITloop; + +/* + * We received a "command complete" message. Put the SCB_TAG into the QOUTFIFO, + * and trigger a completion interrupt. Before doing so, check to see if there + * is a residual or the status byte is something other than STATUS_GOOD (0). + * In either of these conditions, we upload the SCB back to the host so it can + * process this information. In the case of a non zero status byte, we + * additionally interrupt the kernel driver synchronously, allowing it to + * decide if sense should be retrieved. If the kernel driver wishes to request + * sense, it will fill the kernel SCB with a request sense command, requeue + * it to the QINFIFO and tell us not to post to the QOUTFIFO by setting + * RETURN_1 to SEND_SENSE. + */ +mesgin_complete: + + /* + * If ATN is raised, we still want to give the target a message. + * Perhaps there was a parity error on this last message byte. + * Either way, the target should take us to message out phase + * and then attempt to complete the command again. We should use a + * critical section here to guard against a timeout triggering + * for this command and setting ATN while we are still processing + * the completion. + test SCSISIGI, ATNI jnz mesgin_done; + */ + + /* + * If we are identified and have successfully sent the CDB, + * any status will do. Optimize this fast path. + */ + test SCB_CONTROL, STATUS_RCVD jz mesgin_proto_violation; + test SEQ_FLAGS, NOT_IDENTIFIED|NO_CDB_SENT jz complete_accepted; + + /* + * If the target never sent an identify message but instead went + * to mesgin to give an invalid message, let the host abort us. + */ + test SEQ_FLAGS, NOT_IDENTIFIED jnz mesgin_proto_violation; + + /* + * If we recevied good status but never successfully sent the + * cdb, abort the command. + */ + test SCB_SCSI_STATUS,0xff jnz complete_accepted; + test SEQ_FLAGS, NO_CDB_SENT jnz mesgin_proto_violation; + +complete_accepted: + /* + * See if we attempted to deliver a message but the target ingnored us. + */ + test SCB_CONTROL, MK_MESSAGE jz . + 2; + mvi MKMSG_FAILED call set_seqint; + + /* + * Check for residuals + */ + test SCB_SGPTR, SG_LIST_NULL jnz check_status;/* No xfer */ + test SCB_SGPTR, SG_FULL_RESID jnz upload_scb;/* Never xfered */ + test SCB_RESIDUAL_SGPTR, SG_LIST_NULL jz upload_scb; +check_status: + test SCB_SCSI_STATUS,0xff jz complete; /* Good Status? */ +upload_scb: + or SCB_SGPTR, SG_RESID_VALID; + mvi DMAPARAMS, FIFORESET; + mov SCB_TAG call dma_scb; + test SCB_SCSI_STATUS, 0xff jz complete; /* Just a residual? */ + mvi BAD_STATUS call set_seqint; /* let driver know */ + cmp RETURN_1, SEND_SENSE jne complete; + call add_scb_to_free_list; + jmp await_busfree; +complete: + mov SCB_TAG call complete_post; + jmp await_busfree; +} + +complete_post: + /* Post the SCBID in SINDEX and issue an interrupt */ + call add_scb_to_free_list; + mov ARG_1, SINDEX; + if ((ahc->features & AHC_QUEUE_REGS) != 0) { + mov A, SDSCB_QOFF; + } else { + mov A, QOUTPOS; + } + mvi QOUTFIFO_OFFSET call post_byte_setup; + mov ARG_1 call post_byte; + if ((ahc->features & AHC_QUEUE_REGS) == 0) { + inc QOUTPOS; + } + mvi INTSTAT,CMDCMPLT ret; + +if ((ahc->flags & AHC_INITIATORROLE) != 0) { +/* + * Is it a disconnect message? Set a flag in the SCB to remind us + * and await the bus going free. If this is an untagged transaction + * store the SCB id for it in our untagged target table for lookup on + * a reselection. + */ +mesgin_disconnect: + /* + * If ATN is raised, we still want to give the target a message. + * Perhaps there was a parity error on this last message byte + * or we want to abort this command. Either way, the target + * should take us to message out phase and then attempt to + * disconnect again. + * XXX - Wait for more testing. + test SCSISIGI, ATNI jnz mesgin_done; + */ + test SEQ_FLAGS, NOT_IDENTIFIED|NO_CDB_SENT + jnz mesgin_proto_violation; + or SCB_CONTROL,DISCONNECTED; + if ((ahc->flags & AHC_PAGESCBS) != 0) { + call add_scb_to_disc_list; + } + test SCB_CONTROL, TAG_ENB jnz await_busfree; + mov ARG_1, SCB_TAG; + and SAVED_LUN, LID, SCB_LUN; + mov SCB_SCSIID call set_busy_target; + jmp await_busfree; + +/* + * Save data pointers message: + * Copying RAM values back to SCB, for Save Data Pointers message, but + * only if we've actually been into a data phase to change them. This + * protects against bogus data in scratch ram and the residual counts + * since they are only initialized when we go into data_in or data_out. + * Ack the message as soon as possible. For chips without S/G pipelining, + * we can only ack the message after SHADDR has been saved. On these + * chips, SHADDR increments with every bus transaction, even PIO. + */ +mesgin_sdptrs: + if ((ahc->features & AHC_ULTRA2) != 0) { + mov NONE,SCSIDATL; /*dummy read from latch to ACK*/ + test SEQ_FLAGS, DPHASE jz ITloop; + } else { + test SEQ_FLAGS, DPHASE jz mesgin_done; + } + + /* + * If we are asked to save our position at the end of the + * transfer, just mark us at the end rather than perform a + * full save. + */ + test SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL jz mesgin_sdptrs_full; + or SCB_SGPTR, SG_LIST_NULL; + if ((ahc->features & AHC_ULTRA2) != 0) { + jmp ITloop; + } else { + jmp mesgin_done; + } + +mesgin_sdptrs_full: + + /* + * The SCB_SGPTR becomes the next one we'll download, + * and the SCB_DATAPTR becomes the current SHADDR. + * Use the residual number since STCNT is corrupted by + * any message transfer. + */ + if ((ahc->features & AHC_CMD_CHAN) != 0) { + bmov SCB_DATAPTR, SHADDR, 4; + if ((ahc->features & AHC_ULTRA2) == 0) { + mov NONE,SCSIDATL; /*dummy read from latch to ACK*/ + } + bmov SCB_DATACNT, SCB_RESIDUAL_DATACNT, 8; + } else { + mvi DINDEX, SCB_DATAPTR; + mvi SHADDR call bcopy_4; + mov NONE,SCSIDATL; /*dummy read from latch to ACK*/ + mvi SCB_RESIDUAL_DATACNT call bcopy_8; + } + jmp ITloop; + +/* + * Restore pointers message? Data pointers are recopied from the + * SCB anytime we enter a data phase for the first time, so all + * we need to do is clear the DPHASE flag and let the data phase + * code do the rest. We also reset/reallocate the FIFO to make + * sure we have a clean start for the next data or command phase. + */ +mesgin_rdptrs: + and SEQ_FLAGS, ~DPHASE; /* + * We'll reload them + * the next time through + * the dataphase. + */ + or SXFRCTL0, CLRSTCNT|CLRCHN; + jmp mesgin_done; + +/* + * Index into our Busy Target table. SINDEX and DINDEX are modified + * upon return. SCBPTR may be modified by this action. + */ +set_busy_target: + shr DINDEX, 4, SINDEX; + if ((ahc->flags & AHC_SCB_BTT) != 0) { + mov SCBPTR, SAVED_LUN; + add DINDEX, SCB_64_BTT; + } else { + add DINDEX, BUSY_TARGETS; + } + mov DINDIR, ARG_1 ret; + +/* + * Identify message? For a reconnecting target, this tells us the lun + * that the reconnection is for - find the correct SCB and switch to it, + * clearing the "disconnected" bit so we don't "find" it by accident later. + */ +mesgin_identify: + /* + * Determine whether a target is using tagged or non-tagged + * transactions by first looking at the transaction stored in + * the busy target array. If there is no untagged transaction + * for this target or the transaction is for a different lun, then + * this must be a tagged transaction. + */ + shr SINDEX, 4, SAVED_SCSIID; + and SAVED_LUN, MSG_IDENTIFY_LUNMASK, A; + if ((ahc->flags & AHC_SCB_BTT) != 0) { + add SINDEX, SCB_64_BTT; + mov SCBPTR, SAVED_LUN; + if ((ahc->flags & AHC_SEQUENCER_DEBUG) != 0) { + add NONE, -SCB_64_BTT, SINDEX; + jc . + 2; + mvi INTSTAT, OUT_OF_RANGE; + nop; + add NONE, -(SCB_64_BTT + 16), SINDEX; + jnc . + 2; + mvi INTSTAT, OUT_OF_RANGE; + nop; + } + } else { + add SINDEX, BUSY_TARGETS; + if ((ahc->flags & AHC_SEQUENCER_DEBUG) != 0) { + add NONE, -BUSY_TARGETS, SINDEX; + jc . + 2; + mvi INTSTAT, OUT_OF_RANGE; + nop; + add NONE, -(BUSY_TARGETS + 16), SINDEX; + jnc . + 2; + mvi INTSTAT, OUT_OF_RANGE; + nop; + } + } + mov ARG_1, SINDIR; + cmp ARG_1, SCB_LIST_NULL je snoop_tag; + if ((ahc->flags & AHC_PAGESCBS) != 0) { + mov ARG_1 call findSCB; + } else { + mov SCBPTR, ARG_1; + } + if ((ahc->flags & AHC_SCB_BTT) != 0) { + jmp setup_SCB_id_lun_okay; + } else { + /* + * We only allow one untagged command per-target + * at a time. So, if the lun doesn't match, look + * for a tag message. + */ + and A, LID, SCB_LUN; + cmp SAVED_LUN, A je setup_SCB_id_lun_okay; + if ((ahc->flags & AHC_PAGESCBS) != 0) { + /* + * findSCB removes the SCB from the + * disconnected list, so we must replace + * it there should this SCB be for another + * lun. + */ + call cleanup_scb; + } + } + +/* + * Here we "snoop" the bus looking for a SIMPLE QUEUE TAG message. + * If we get one, we use the tag returned to find the proper + * SCB. With SCB paging, we must search for non-tagged + * transactions since the SCB may exist in any slot. If we're not + * using SCB paging, we can use the tag as the direct index to the + * SCB. + */ +snoop_tag: + if ((ahc->flags & AHC_SEQUENCER_DEBUG) != 0) { + or SEQ_FLAGS, 0x80; + } + mov NONE,SCSIDATL; /* ACK Identify MSG */ + call phase_lock; + if ((ahc->flags & AHC_SEQUENCER_DEBUG) != 0) { + or SEQ_FLAGS, 0x1; + } + cmp LASTPHASE, P_MESGIN jne not_found; + if ((ahc->flags & AHC_SEQUENCER_DEBUG) != 0) { + or SEQ_FLAGS, 0x2; + } + cmp SCSIBUSL,MSG_SIMPLE_Q_TAG jne not_found; +get_tag: + if ((ahc->flags & AHC_PAGESCBS) != 0) { + mvi ARG_1 call inb_next; /* tag value */ + mov ARG_1 call findSCB; + } else { + mvi ARG_1 call inb_next; /* tag value */ + mov SCBPTR, ARG_1; + } + +/* + * Ensure that the SCB the tag points to is for + * an SCB transaction to the reconnecting target. + */ +setup_SCB: + if ((ahc->flags & AHC_SEQUENCER_DEBUG) != 0) { + or SEQ_FLAGS, 0x4; + } + mov A, SCB_SCSIID; + cmp SAVED_SCSIID, A jne not_found_cleanup_scb; + if ((ahc->flags & AHC_SEQUENCER_DEBUG) != 0) { + or SEQ_FLAGS, 0x8; + } +setup_SCB_id_okay: + and A, LID, SCB_LUN; + cmp SAVED_LUN, A jne not_found_cleanup_scb; +setup_SCB_id_lun_okay: + if ((ahc->flags & AHC_SEQUENCER_DEBUG) != 0) { + or SEQ_FLAGS, 0x10; + } + test SCB_CONTROL,DISCONNECTED jz not_found_cleanup_scb; + and SCB_CONTROL,~DISCONNECTED; + test SCB_CONTROL, TAG_ENB jnz setup_SCB_tagged; + if ((ahc->flags & AHC_SCB_BTT) != 0) { + mov A, SCBPTR; + } + mvi ARG_1, SCB_LIST_NULL; + mov SAVED_SCSIID call set_busy_target; + if ((ahc->flags & AHC_SCB_BTT) != 0) { + mov SCBPTR, A; + } +setup_SCB_tagged: + clr SEQ_FLAGS; /* make note of IDENTIFY */ + call set_transfer_settings; + /* See if the host wants to send a message upon reconnection */ + test SCB_CONTROL, MK_MESSAGE jz mesgin_done; + mvi HOST_MSG call mk_mesg; + jmp mesgin_done; + +not_found_cleanup_scb: + if ((ahc->flags & AHC_PAGESCBS) != 0) { + call cleanup_scb; + } +not_found: + mvi NO_MATCH call set_seqint; + jmp mesgin_done; + +mk_mesg: + if ((ahc->features & AHC_DT) == 0) { + or SCSISIGO, ATNO, LASTPHASE; + } else { + mvi SCSISIGO, ATNO; + } + mov MSG_OUT,SINDEX ret; + +/* + * Functions to read data in Automatic PIO mode. + * + * According to Adaptec's documentation, an ACK is not sent on input from + * the target until SCSIDATL is read from. So we wait until SCSIDATL is + * latched (the usual way), then read the data byte directly off the bus + * using SCSIBUSL. When we have pulled the ATN line, or we just want to + * acknowledge the byte, then we do a dummy read from SCISDATL. The SCSI + * spec guarantees that the target will hold the data byte on the bus until + * we send our ACK. + * + * The assumption here is that these are called in a particular sequence, + * and that REQ is already set when inb_first is called. inb_{first,next} + * use the same calling convention as inb. + */ +inb_next_wait_perr: + mvi PERR_DETECTED call set_seqint; + jmp inb_next_wait; +inb_next: + mov NONE,SCSIDATL; /*dummy read from latch to ACK*/ +inb_next_wait: + /* + * If there is a parity error, wait for the kernel to + * see the interrupt and prepare our message response + * before continuing. + */ + test SSTAT1, REQINIT jz inb_next_wait; + test SSTAT1, SCSIPERR jnz inb_next_wait_perr; +inb_next_check_phase: + and LASTPHASE, PHASE_MASK, SCSISIGI; + cmp LASTPHASE, P_MESGIN jne mesgin_phasemis; +inb_first: + mov DINDEX,SINDEX; + mov DINDIR,SCSIBUSL ret; /*read byte directly from bus*/ +inb_last: + mov NONE,SCSIDATL ret; /*dummy read from latch to ACK*/ +} + +if ((ahc->flags & AHC_TARGETROLE) != 0) { +/* + * Change to a new phase. If we are changing the state of the I/O signal, + * from out to in, wait an additional data release delay before continuing. + */ +change_phase: + /* Wait for preceding I/O session to complete. */ + test SCSISIGI, ACKI jnz .; + + /* Change the phase */ + and DINDEX, IOI, SCSISIGI; + mov SCSISIGO, SINDEX; + and A, IOI, SINDEX; + + /* + * If the data direction has changed, from + * out (initiator driving) to in (target driving), + * we must wait at least a data release delay plus + * the normal bus settle delay. [SCSI III SPI 10.11.0] + */ + cmp DINDEX, A je change_phase_wait; + test SINDEX, IOI jz change_phase_wait; + call change_phase_wait; +change_phase_wait: + nop; + nop; + nop; + nop ret; + +/* + * Send a byte to an initiator in Automatic PIO mode. + */ +target_outb: + or SXFRCTL0, SPIOEN; + test SSTAT0, SPIORDY jz .; + mov SCSIDATL, SINDEX; + test SSTAT0, SPIORDY jz .; + and SXFRCTL0, ~SPIOEN ret; +} + +/* + * Locate a disconnected SCB by SCBID. Upon return, SCBPTR and SINDEX will + * be set to the position of the SCB. If the SCB cannot be found locally, + * it will be paged in from host memory. RETURN_2 stores the address of the + * preceding SCB in the disconnected list which can be used to speed up + * removal of the found SCB from the disconnected list. + */ +if ((ahc->flags & AHC_PAGESCBS) != 0) { +BEGIN_CRITICAL; +findSCB: + mov A, SINDEX; /* Tag passed in SINDEX */ + cmp DISCONNECTED_SCBH, SCB_LIST_NULL je findSCB_notFound; + mov SCBPTR, DISCONNECTED_SCBH; /* Initialize SCBPTR */ + mvi ARG_2, SCB_LIST_NULL; /* Head of list */ + jmp findSCB_loop; +findSCB_next: + cmp SCB_NEXT, SCB_LIST_NULL je findSCB_notFound; + mov ARG_2, SCBPTR; + mov SCBPTR,SCB_NEXT; +findSCB_loop: + cmp SCB_TAG, A jne findSCB_next; +rem_scb_from_disc_list: + cmp ARG_2, SCB_LIST_NULL je rHead; + mov DINDEX, SCB_NEXT; + mov SINDEX, SCBPTR; + mov SCBPTR, ARG_2; + mov SCB_NEXT, DINDEX; + mov SCBPTR, SINDEX ret; +rHead: + mov DISCONNECTED_SCBH,SCB_NEXT ret; +END_CRITICAL; +findSCB_notFound: + /* + * We didn't find it. Page in the SCB. + */ + mov ARG_1, A; /* Save tag */ + mov ALLZEROS call get_free_or_disc_scb; + mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET; + mov ARG_1 jmp dma_scb; +} + +/* + * Prepare the hardware to post a byte to host memory given an + * index of (A + (256 * SINDEX)) and a base address of SHARED_DATA_ADDR. + */ +post_byte_setup: + mov ARG_2, SINDEX; + if ((ahc->features & AHC_CMD_CHAN) != 0) { + mvi DINDEX, CCHADDR; + mvi SHARED_DATA_ADDR call set_1byte_addr; + mvi CCHCNT, 1; + mvi CCSCBCTL, CCSCBRESET ret; + } else { + mvi DINDEX, HADDR; + mvi SHARED_DATA_ADDR call set_1byte_addr; + mvi 1 call set_hcnt; + mvi DFCNTRL, FIFORESET ret; + } + +post_byte: + if ((ahc->features & AHC_CMD_CHAN) != 0) { + bmov CCSCBRAM, SINDEX, 1; + or CCSCBCTL, CCSCBEN|CCSCBRESET; + test CCSCBCTL, CCSCBDONE jz .; + clr CCSCBCTL ret; + } else { + mov DFDAT, SINDEX; + or DFCNTRL, HDMAEN|FIFOFLUSH; + jmp dma_finish; + } + +phase_lock_perr: + mvi PERR_DETECTED call set_seqint; +phase_lock: + /* + * If there is a parity error, wait for the kernel to + * see the interrupt and prepare our message response + * before continuing. + */ + test SSTAT1, REQINIT jz phase_lock; + test SSTAT1, SCSIPERR jnz phase_lock_perr; +phase_lock_latch_phase: + if ((ahc->features & AHC_DT) == 0) { + and SCSISIGO, PHASE_MASK, SCSISIGI; + } + and LASTPHASE, PHASE_MASK, SCSISIGI ret; + +if ((ahc->features & AHC_CMD_CHAN) == 0) { +set_hcnt: + mov HCNT[0], SINDEX; +clear_hcnt: + clr HCNT[1]; + clr HCNT[2] ret; + +set_stcnt_from_hcnt: + mov STCNT[0], HCNT[0]; + mov STCNT[1], HCNT[1]; + mov STCNT[2], HCNT[2] ret; + +bcopy_8: + mov DINDIR, SINDIR; +bcopy_7: + mov DINDIR, SINDIR; + mov DINDIR, SINDIR; +bcopy_5: + mov DINDIR, SINDIR; +bcopy_4: + mov DINDIR, SINDIR; +bcopy_3: + mov DINDIR, SINDIR; + mov DINDIR, SINDIR; + mov DINDIR, SINDIR ret; +} + +if ((ahc->flags & AHC_TARGETROLE) != 0) { +/* + * Setup addr assuming that A is an index into + * an array of 32byte objects, SINDEX contains + * the base address of that array, and DINDEX + * contains the base address of the location + * to store the indexed address. + */ +set_32byte_addr: + shr ARG_2, 3, A; + shl A, 5; + jmp set_1byte_addr; +} + +/* + * Setup addr assuming that A is an index into + * an array of 64byte objects, SINDEX contains + * the base address of that array, and DINDEX + * contains the base address of the location + * to store the indexed address. + */ +set_64byte_addr: + shr ARG_2, 2, A; + shl A, 6; + +/* + * Setup addr assuming that A + (ARG_2 * 256) is an + * index into an array of 1byte objects, SINDEX contains + * the base address of that array, and DINDEX contains + * the base address of the location to store the computed + * address. + */ +set_1byte_addr: + add DINDIR, A, SINDIR; + mov A, ARG_2; + adc DINDIR, A, SINDIR; + clr A; + adc DINDIR, A, SINDIR; + adc DINDIR, A, SINDIR ret; + +/* + * Either post or fetch an SCB from host memory based on the + * DIRECTION bit in DMAPARAMS. The host SCB index is in SINDEX. + */ +dma_scb: + mov A, SINDEX; + if ((ahc->features & AHC_CMD_CHAN) != 0) { + mvi DINDEX, CCHADDR; + mvi HSCB_ADDR call set_64byte_addr; + mov CCSCBPTR, SCBPTR; + test DMAPARAMS, DIRECTION jz dma_scb_tohost; + if ((ahc->flags & AHC_SCB_BTT) != 0) { + mvi CCHCNT, SCB_DOWNLOAD_SIZE_64; + } else { + mvi CCHCNT, SCB_DOWNLOAD_SIZE; + } + mvi CCSCBCTL, CCARREN|CCSCBEN|CCSCBDIR|CCSCBRESET; + cmp CCSCBCTL, CCSCBDONE|ARRDONE|CCARREN|CCSCBEN|CCSCBDIR jne .; + jmp dma_scb_finish; +dma_scb_tohost: + mvi CCHCNT, SCB_UPLOAD_SIZE; + if ((ahc->features & AHC_ULTRA2) == 0) { + mvi CCSCBCTL, CCSCBRESET; + bmov CCSCBRAM, SCB_BASE, SCB_UPLOAD_SIZE; + or CCSCBCTL, CCSCBEN|CCSCBRESET; + test CCSCBCTL, CCSCBDONE jz .; + } else if ((ahc->bugs & AHC_SCBCHAN_UPLOAD_BUG) != 0) { + mvi CCSCBCTL, CCARREN|CCSCBRESET; + cmp CCSCBCTL, ARRDONE|CCARREN jne .; + mvi CCHCNT, SCB_UPLOAD_SIZE; + mvi CCSCBCTL, CCSCBEN|CCSCBRESET; + cmp CCSCBCTL, CCSCBDONE|CCSCBEN jne .; + } else { + mvi CCSCBCTL, CCARREN|CCSCBEN|CCSCBRESET; + cmp CCSCBCTL, CCSCBDONE|ARRDONE|CCARREN|CCSCBEN jne .; + } +dma_scb_finish: + clr CCSCBCTL; + test CCSCBCTL, CCARREN|CCSCBEN jnz .; + ret; + } else { + mvi DINDEX, HADDR; + mvi HSCB_ADDR call set_64byte_addr; + mvi SCB_DOWNLOAD_SIZE call set_hcnt; + mov DFCNTRL, DMAPARAMS; + test DMAPARAMS, DIRECTION jnz dma_scb_fromhost; + /* Fill it with the SCB data */ +copy_scb_tofifo: + mvi SINDEX, SCB_BASE; + add A, SCB_DOWNLOAD_SIZE, SINDEX; +copy_scb_tofifo_loop: + call copy_to_fifo_8; + cmp SINDEX, A jne copy_scb_tofifo_loop; + or DFCNTRL, HDMAEN|FIFOFLUSH; + jmp dma_finish; +dma_scb_fromhost: + mvi DINDEX, SCB_BASE; + if ((ahc->bugs & AHC_PCI_2_1_RETRY_BUG) != 0) { + /* + * The PCI module will only issue a PCI + * retry if the data FIFO is empty. If the + * host disconnects in the middle of a + * transfer, we must empty the fifo of all + * available data to force the chip to + * continue the transfer. This does not + * happen for SCSI transfers as the SCSI module + * will drain the FIFO as data are made available. + * When the hang occurs, we know that a multiple + * of 8 bytes is in the FIFO because the PCI + * module has an 8 byte input latch that only + * dumps to the FIFO when HCNT == 0 or the + * latch is full. + */ + clr A; + /* Wait for at least 8 bytes of data to arrive. */ +dma_scb_hang_fifo: + test DFSTATUS, FIFOQWDEMP jnz dma_scb_hang_fifo; +dma_scb_hang_wait: + test DFSTATUS, MREQPEND jnz dma_scb_hang_wait; + test DFSTATUS, HDONE jnz dma_scb_hang_dma_done; + test DFSTATUS, HDONE jnz dma_scb_hang_dma_done; + test DFSTATUS, HDONE jnz dma_scb_hang_dma_done; + /* + * The PCI module no longer intends to perform + * a PCI transaction. Drain the fifo. + */ +dma_scb_hang_dma_drain_fifo: + not A, HCNT; + add A, SCB_DOWNLOAD_SIZE+SCB_BASE+1; + and A, ~0x7; + mov DINDIR,DFDAT; + cmp DINDEX, A jne . - 1; + cmp DINDEX, SCB_DOWNLOAD_SIZE+SCB_BASE + je dma_finish_nowait; + /* Restore A as the lines left to transfer. */ + add A, -SCB_BASE, DINDEX; + shr A, 3; + jmp dma_scb_hang_fifo; +dma_scb_hang_dma_done: + and DFCNTRL, ~HDMAEN; + test DFCNTRL, HDMAEN jnz .; + add SEQADDR0, A; + } else { + call dma_finish; + } + call dfdat_in_8; + call dfdat_in_8; + call dfdat_in_8; +dfdat_in_8: + mov DINDIR,DFDAT; +dfdat_in_7: + mov DINDIR,DFDAT; + mov DINDIR,DFDAT; + mov DINDIR,DFDAT; + mov DINDIR,DFDAT; + mov DINDIR,DFDAT; +dfdat_in_2: + mov DINDIR,DFDAT; + mov DINDIR,DFDAT ret; + } + +copy_to_fifo_8: + mov DFDAT,SINDIR; + mov DFDAT,SINDIR; +copy_to_fifo_6: + mov DFDAT,SINDIR; +copy_to_fifo_5: + mov DFDAT,SINDIR; +copy_to_fifo_4: + mov DFDAT,SINDIR; + mov DFDAT,SINDIR; + mov DFDAT,SINDIR; + mov DFDAT,SINDIR ret; + +/* + * Wait for DMA from host memory to data FIFO to complete, then disable + * DMA and wait for it to acknowledge that it's off. + */ +dma_finish: + test DFSTATUS,HDONE jz dma_finish; +dma_finish_nowait: + /* Turn off DMA */ + and DFCNTRL, ~HDMAEN; + test DFCNTRL, HDMAEN jnz .; + ret; + +/* + * Restore an SCB that failed to match an incoming reselection + * to the correct/safe state. If the SCB is for a disconnected + * transaction, it must be returned to the disconnected list. + * If it is not in the disconnected state, it must be free. + */ +cleanup_scb: + if ((ahc->flags & AHC_PAGESCBS) != 0) { + test SCB_CONTROL,DISCONNECTED jnz add_scb_to_disc_list; + } +add_scb_to_free_list: + if ((ahc->flags & AHC_PAGESCBS) != 0) { +BEGIN_CRITICAL; + mov SCB_NEXT, FREE_SCBH; + mvi SCB_TAG, SCB_LIST_NULL; + mov FREE_SCBH, SCBPTR ret; +END_CRITICAL; + } else { + mvi SCB_TAG, SCB_LIST_NULL ret; + } + +if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) { +set_hhaddr: + or DSCOMMAND1, HADDLDSEL0; + and HADDR, SG_HIGH_ADDR_BITS, SINDEX; + and DSCOMMAND1, ~HADDLDSEL0 ret; +} + +if ((ahc->flags & AHC_PAGESCBS) != 0) { +get_free_or_disc_scb: +BEGIN_CRITICAL; + cmp FREE_SCBH, SCB_LIST_NULL jne dequeue_free_scb; + cmp DISCONNECTED_SCBH, SCB_LIST_NULL jne dequeue_disc_scb; +return_error: + mvi NO_FREE_SCB call set_seqint; + mvi SINDEX, SCB_LIST_NULL ret; +dequeue_disc_scb: + mov SCBPTR, DISCONNECTED_SCBH; + mov DISCONNECTED_SCBH, SCB_NEXT; +END_CRITICAL; + mvi DMAPARAMS, FIFORESET; + mov SCB_TAG jmp dma_scb; +BEGIN_CRITICAL; +dequeue_free_scb: + mov SCBPTR, FREE_SCBH; + mov FREE_SCBH, SCB_NEXT ret; +END_CRITICAL; + +add_scb_to_disc_list: +/* + * Link this SCB into the DISCONNECTED list. This list holds the + * candidates for paging out an SCB if one is needed for a new command. + * Modifying the disconnected list is a critical(pause dissabled) section. + */ +BEGIN_CRITICAL; + mov SCB_NEXT, DISCONNECTED_SCBH; + mov DISCONNECTED_SCBH, SCBPTR ret; +END_CRITICAL; +} +set_seqint: + mov INTSTAT, SINDEX; + nop; +return: + ret; diff --git a/drivers/scsi/aic7xxx/aic7xxx_93cx6.c b/drivers/scsi/aic7xxx/aic7xxx_93cx6.c new file mode 100644 index 000000000..cc9e41967 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx_93cx6.c @@ -0,0 +1,318 @@ +/* + * Interface for the 93C66/56/46/26/06 serial eeprom parts. + * + * Copyright (c) 1995, 1996 Daniel M. Eischen + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. The name of the author may not be used to endorse or promote products + * derived from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL"). + * + * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR + * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * $Id: //depot/aic7xxx/aic7xxx/aic7xxx_93cx6.c#19 $ + */ + +/* + * The instruction set of the 93C66/56/46/26/06 chips are as follows: + * + * Start OP * + * Function Bit Code Address** Data Description + * ------------------------------------------------------------------- + * READ 1 10 A5 - A0 Reads data stored in memory, + * starting at specified address + * EWEN 1 00 11XXXX Write enable must precede + * all programming modes + * ERASE 1 11 A5 - A0 Erase register A5A4A3A2A1A0 + * WRITE 1 01 A5 - A0 D15 - D0 Writes register + * ERAL 1 00 10XXXX Erase all registers + * WRAL 1 00 01XXXX D15 - D0 Writes to all registers + * EWDS 1 00 00XXXX Disables all programming + * instructions + * *Note: A value of X for address is a don't care condition. + * **Note: There are 8 address bits for the 93C56/66 chips unlike + * the 93C46/26/06 chips which have 6 address bits. + * + * The 93C46 has a four wire interface: clock, chip select, data in, and + * data out. In order to perform one of the above functions, you need + * to enable the chip select for a clock period (typically a minimum of + * 1 usec, with the clock high and low a minimum of 750 and 250 nsec + * respectively). While the chip select remains high, you can clock in + * the instructions (above) starting with the start bit, followed by the + * OP code, Address, and Data (if needed). For the READ instruction, the + * requested 16-bit register contents is read from the data out line but + * is preceded by an initial zero (leading 0, followed by 16-bits, MSB + * first). The clock cycling from low to high initiates the next data + * bit to be sent from the chip. + */ + +#include "aic7xxx_osm.h" +#include "aic7xxx_inline.h" +#include "aic7xxx_93cx6.h" + +/* + * Right now, we only have to read the SEEPROM. But we make it easier to + * add other 93Cx6 functions. + */ +struct seeprom_cmd { + uint8_t len; + uint8_t bits[11]; +}; + +/* Short opcodes for the c46 */ +static const struct seeprom_cmd seeprom_ewen = {9, {1, 0, 0, 1, 1, 0, 0, 0, 0}}; +static const struct seeprom_cmd seeprom_ewds = {9, {1, 0, 0, 0, 0, 0, 0, 0, 0}}; + +/* Long opcodes for the C56/C66 */ +static const struct seeprom_cmd seeprom_long_ewen = {11, {1, 0, 0, 1, 1, 0, 0, 0, 0}}; +static const struct seeprom_cmd seeprom_long_ewds = {11, {1, 0, 0, 0, 0, 0, 0, 0, 0}}; + +/* Common opcodes */ +static const struct seeprom_cmd seeprom_write = {3, {1, 0, 1}}; +static const struct seeprom_cmd seeprom_read = {3, {1, 1, 0}}; + +/* + * Wait for the SEERDY to go high; about 800 ns. + */ +#define CLOCK_PULSE(sd, rdy) \ + while ((SEEPROM_STATUS_INB(sd) & rdy) == 0) { \ + ; /* Do nothing */ \ + } \ + (void)SEEPROM_INB(sd); /* Clear clock */ + +/* + * Send a START condition and the given command + */ +static void +send_seeprom_cmd(struct seeprom_descriptor *sd, const struct seeprom_cmd *cmd) +{ + uint8_t temp; + int i = 0; + + /* Send chip select for one clock cycle. */ + temp = sd->sd_MS ^ sd->sd_CS; + SEEPROM_OUTB(sd, temp ^ sd->sd_CK); + CLOCK_PULSE(sd, sd->sd_RDY); + + for (i = 0; i < cmd->len; i++) { + if (cmd->bits[i] != 0) + temp ^= sd->sd_DO; + SEEPROM_OUTB(sd, temp); + CLOCK_PULSE(sd, sd->sd_RDY); + SEEPROM_OUTB(sd, temp ^ sd->sd_CK); + CLOCK_PULSE(sd, sd->sd_RDY); + if (cmd->bits[i] != 0) + temp ^= sd->sd_DO; + } +} + +/* + * Clear CS put the chip in the reset state, where it can wait for new commands. + */ +static void +reset_seeprom(struct seeprom_descriptor *sd) +{ + uint8_t temp; + + temp = sd->sd_MS; + SEEPROM_OUTB(sd, temp); + CLOCK_PULSE(sd, sd->sd_RDY); + SEEPROM_OUTB(sd, temp ^ sd->sd_CK); + CLOCK_PULSE(sd, sd->sd_RDY); + SEEPROM_OUTB(sd, temp); + CLOCK_PULSE(sd, sd->sd_RDY); +} + +/* + * Read the serial EEPROM and returns 1 if successful and 0 if + * not successful. + */ +int +ahc_read_seeprom(struct seeprom_descriptor *sd, uint16_t *buf, + u_int start_addr, u_int count) +{ + int i = 0; + u_int k = 0; + uint16_t v; + uint8_t temp; + + /* + * Read the requested registers of the seeprom. The loop + * will range from 0 to count-1. + */ + for (k = start_addr; k < count + start_addr; k++) { + /* + * Now we're ready to send the read command followed by the + * address of the 16-bit register we want to read. + */ + send_seeprom_cmd(sd, &seeprom_read); + + /* Send the 6 or 8 bit address (MSB first, LSB last). */ + temp = sd->sd_MS ^ sd->sd_CS; + for (i = (sd->sd_chip - 1); i >= 0; i--) { + if ((k & (1 << i)) != 0) + temp ^= sd->sd_DO; + SEEPROM_OUTB(sd, temp); + CLOCK_PULSE(sd, sd->sd_RDY); + SEEPROM_OUTB(sd, temp ^ sd->sd_CK); + CLOCK_PULSE(sd, sd->sd_RDY); + if ((k & (1 << i)) != 0) + temp ^= sd->sd_DO; + } + + /* + * Now read the 16 bit register. An initial 0 precedes the + * register contents which begins with bit 15 (MSB) and ends + * with bit 0 (LSB). The initial 0 will be shifted off the + * top of our word as we let the loop run from 0 to 16. + */ + v = 0; + for (i = 16; i >= 0; i--) { + SEEPROM_OUTB(sd, temp); + CLOCK_PULSE(sd, sd->sd_RDY); + v <<= 1; + if (SEEPROM_DATA_INB(sd) & sd->sd_DI) + v |= 1; + SEEPROM_OUTB(sd, temp ^ sd->sd_CK); + CLOCK_PULSE(sd, sd->sd_RDY); + } + + buf[k - start_addr] = v; + + /* Reset the chip select for the next command cycle. */ + reset_seeprom(sd); + } +#ifdef AHC_DUMP_EEPROM + printk("\nSerial EEPROM:\n\t"); + for (k = 0; k < count; k = k + 1) { + if (((k % 8) == 0) && (k != 0)) { + printk(KERN_CONT "\n\t"); + } + printk(KERN_CONT " 0x%x", buf[k]); + } + printk(KERN_CONT "\n"); +#endif + return (1); +} + +/* + * Write the serial EEPROM and return 1 if successful and 0 if + * not successful. + */ +int +ahc_write_seeprom(struct seeprom_descriptor *sd, uint16_t *buf, + u_int start_addr, u_int count) +{ + const struct seeprom_cmd *ewen, *ewds; + uint16_t v; + uint8_t temp; + int i, k; + + /* Place the chip into write-enable mode */ + if (sd->sd_chip == C46) { + ewen = &seeprom_ewen; + ewds = &seeprom_ewds; + } else if (sd->sd_chip == C56_66) { + ewen = &seeprom_long_ewen; + ewds = &seeprom_long_ewds; + } else { + printk("ahc_write_seeprom: unsupported seeprom type %d\n", + sd->sd_chip); + return (0); + } + + send_seeprom_cmd(sd, ewen); + reset_seeprom(sd); + + /* Write all requested data out to the seeprom. */ + temp = sd->sd_MS ^ sd->sd_CS; + for (k = start_addr; k < count + start_addr; k++) { + /* Send the write command */ + send_seeprom_cmd(sd, &seeprom_write); + + /* Send the 6 or 8 bit address (MSB first). */ + for (i = (sd->sd_chip - 1); i >= 0; i--) { + if ((k & (1 << i)) != 0) + temp ^= sd->sd_DO; + SEEPROM_OUTB(sd, temp); + CLOCK_PULSE(sd, sd->sd_RDY); + SEEPROM_OUTB(sd, temp ^ sd->sd_CK); + CLOCK_PULSE(sd, sd->sd_RDY); + if ((k & (1 << i)) != 0) + temp ^= sd->sd_DO; + } + + /* Write the 16 bit value, MSB first */ + v = buf[k - start_addr]; + for (i = 15; i >= 0; i--) { + if ((v & (1 << i)) != 0) + temp ^= sd->sd_DO; + SEEPROM_OUTB(sd, temp); + CLOCK_PULSE(sd, sd->sd_RDY); + SEEPROM_OUTB(sd, temp ^ sd->sd_CK); + CLOCK_PULSE(sd, sd->sd_RDY); + if ((v & (1 << i)) != 0) + temp ^= sd->sd_DO; + } + + /* Wait for the chip to complete the write */ + temp = sd->sd_MS; + SEEPROM_OUTB(sd, temp); + CLOCK_PULSE(sd, sd->sd_RDY); + temp = sd->sd_MS ^ sd->sd_CS; + do { + SEEPROM_OUTB(sd, temp); + CLOCK_PULSE(sd, sd->sd_RDY); + SEEPROM_OUTB(sd, temp ^ sd->sd_CK); + CLOCK_PULSE(sd, sd->sd_RDY); + } while ((SEEPROM_DATA_INB(sd) & sd->sd_DI) == 0); + + reset_seeprom(sd); + } + + /* Put the chip back into write-protect mode */ + send_seeprom_cmd(sd, ewds); + reset_seeprom(sd); + + return (1); +} + +int +ahc_verify_cksum(struct seeprom_config *sc) +{ + int i; + int maxaddr; + uint32_t checksum; + uint16_t *scarray; + + maxaddr = (sizeof(*sc)/2) - 1; + checksum = 0; + scarray = (uint16_t *)sc; + + for (i = 0; i < maxaddr; i++) + checksum = checksum + scarray[i]; + if (checksum == 0 + || (checksum & 0xFFFF) != sc->checksum) { + return (0); + } else { + return(1); + } +} diff --git a/drivers/scsi/aic7xxx/aic7xxx_93cx6.h b/drivers/scsi/aic7xxx/aic7xxx_93cx6.h new file mode 100644 index 000000000..859c43ccd --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx_93cx6.h @@ -0,0 +1,102 @@ +/* + * Interface to the 93C46/56 serial EEPROM that is used to store BIOS + * settings for the aic7xxx based adaptec SCSI controllers. It can + * also be used for 93C26 and 93C06 serial EEPROMS. + * + * Copyright (c) 1994, 1995, 2000 Justin T. Gibbs. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aic7xxx_93cx6.h#12 $ + * + * $FreeBSD$ + */ +#ifndef _AIC7XXX_93CX6_H_ +#define _AIC7XXX_93CX6_H_ + +typedef enum { + C46 = 6, + C56_66 = 8 +} seeprom_chip_t; + +struct seeprom_descriptor { + struct ahc_softc *sd_ahc; + u_int sd_control_offset; + u_int sd_status_offset; + u_int sd_dataout_offset; + seeprom_chip_t sd_chip; + uint16_t sd_MS; + uint16_t sd_RDY; + uint16_t sd_CS; + uint16_t sd_CK; + uint16_t sd_DO; + uint16_t sd_DI; +}; + +/* + * This function will read count 16-bit words from the serial EEPROM and + * return their value in buf. The port address of the aic7xxx serial EEPROM + * control register is passed in as offset. The following parameters are + * also passed in: + * + * CS - Chip select + * CK - Clock + * DO - Data out + * DI - Data in + * RDY - SEEPROM ready + * MS - Memory port mode select + * + * A failed read attempt returns 0, and a successful read returns 1. + */ + +#define SEEPROM_INB(sd) \ + ahc_inb(sd->sd_ahc, sd->sd_control_offset) +#define SEEPROM_OUTB(sd, value) \ +do { \ + ahc_outb(sd->sd_ahc, sd->sd_control_offset, value); \ + ahc_flush_device_writes(sd->sd_ahc); \ +} while(0) + +#define SEEPROM_STATUS_INB(sd) \ + ahc_inb(sd->sd_ahc, sd->sd_status_offset) +#define SEEPROM_DATA_INB(sd) \ + ahc_inb(sd->sd_ahc, sd->sd_dataout_offset) + +int ahc_read_seeprom(struct seeprom_descriptor *sd, uint16_t *buf, + u_int start_addr, u_int count); +int ahc_write_seeprom(struct seeprom_descriptor *sd, uint16_t *buf, + u_int start_addr, u_int count); +int ahc_verify_cksum(struct seeprom_config *sc); + +#endif /* _AIC7XXX_93CX6_H_ */ diff --git a/drivers/scsi/aic7xxx/aic7xxx_core.c b/drivers/scsi/aic7xxx/aic7xxx_core.c new file mode 100644 index 000000000..12fed15de --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx_core.c @@ -0,0 +1,7908 @@ +/* + * Core routines and tables shareable across OS platforms. + * + * Copyright (c) 1994-2002 Justin T. Gibbs. + * Copyright (c) 2000-2002 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aic7xxx.c#155 $ + */ + +#include "aic7xxx_osm.h" +#include "aic7xxx_inline.h" +#include "aicasm/aicasm_insformat.h" + +/***************************** Lookup Tables **********************************/ +static const char *const ahc_chip_names[] = { + "NONE", + "aic7770", + "aic7850", + "aic7855", + "aic7859", + "aic7860", + "aic7870", + "aic7880", + "aic7895", + "aic7895C", + "aic7890/91", + "aic7896/97", + "aic7892", + "aic7899" +}; + +/* + * Hardware error codes. + */ +struct ahc_hard_error_entry { + uint8_t errno; + const char *errmesg; +}; + +static const struct ahc_hard_error_entry ahc_hard_errors[] = { + { ILLHADDR, "Illegal Host Access" }, + { ILLSADDR, "Illegal Sequencer Address referenced" }, + { ILLOPCODE, "Illegal Opcode in sequencer program" }, + { SQPARERR, "Sequencer Parity Error" }, + { DPARERR, "Data-path Parity Error" }, + { MPARERR, "Scratch or SCB Memory Parity Error" }, + { PCIERRSTAT, "PCI Error detected" }, + { CIOPARERR, "CIOBUS Parity Error" }, +}; +static const u_int num_errors = ARRAY_SIZE(ahc_hard_errors); + +static const struct ahc_phase_table_entry ahc_phase_table[] = +{ + { P_DATAOUT, MSG_NOOP, "in Data-out phase" }, + { P_DATAIN, MSG_INITIATOR_DET_ERR, "in Data-in phase" }, + { P_DATAOUT_DT, MSG_NOOP, "in DT Data-out phase" }, + { P_DATAIN_DT, MSG_INITIATOR_DET_ERR, "in DT Data-in phase" }, + { P_COMMAND, MSG_NOOP, "in Command phase" }, + { P_MESGOUT, MSG_NOOP, "in Message-out phase" }, + { P_STATUS, MSG_INITIATOR_DET_ERR, "in Status phase" }, + { P_MESGIN, MSG_PARITY_ERROR, "in Message-in phase" }, + { P_BUSFREE, MSG_NOOP, "while idle" }, + { 0, MSG_NOOP, "in unknown phase" } +}; + +/* + * In most cases we only wish to itterate over real phases, so + * exclude the last element from the count. + */ +static const u_int num_phases = ARRAY_SIZE(ahc_phase_table) - 1; + +/* + * Valid SCSIRATE values. (p. 3-17) + * Provides a mapping of tranfer periods in ns to the proper value to + * stick in the scsixfer reg. + */ +static const struct ahc_syncrate ahc_syncrates[] = +{ + /* ultra2 fast/ultra period rate */ + { 0x42, 0x000, 9, "80.0" }, + { 0x03, 0x000, 10, "40.0" }, + { 0x04, 0x000, 11, "33.0" }, + { 0x05, 0x100, 12, "20.0" }, + { 0x06, 0x110, 15, "16.0" }, + { 0x07, 0x120, 18, "13.4" }, + { 0x08, 0x000, 25, "10.0" }, + { 0x19, 0x010, 31, "8.0" }, + { 0x1a, 0x020, 37, "6.67" }, + { 0x1b, 0x030, 43, "5.7" }, + { 0x1c, 0x040, 50, "5.0" }, + { 0x00, 0x050, 56, "4.4" }, + { 0x00, 0x060, 62, "4.0" }, + { 0x00, 0x070, 68, "3.6" }, + { 0x00, 0x000, 0, NULL } +}; + +/* Our Sequencer Program */ +#include "aic7xxx_seq.h" + +/**************************** Function Declarations ***************************/ +static void ahc_force_renegotiation(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo); +static struct ahc_tmode_tstate* + ahc_alloc_tstate(struct ahc_softc *ahc, + u_int scsi_id, char channel); +#ifdef AHC_TARGET_MODE +static void ahc_free_tstate(struct ahc_softc *ahc, + u_int scsi_id, char channel, int force); +#endif +static const struct ahc_syncrate* + ahc_devlimited_syncrate(struct ahc_softc *ahc, + struct ahc_initiator_tinfo *, + u_int *period, + u_int *ppr_options, + role_t role); +static void ahc_update_pending_scbs(struct ahc_softc *ahc); +static void ahc_fetch_devinfo(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo); +static void ahc_scb_devinfo(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo, + struct scb *scb); +static void ahc_assert_atn(struct ahc_softc *ahc); +static void ahc_setup_initiator_msgout(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo, + struct scb *scb); +static void ahc_build_transfer_msg(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo); +static void ahc_construct_sdtr(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo, + u_int period, u_int offset); +static void ahc_construct_wdtr(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo, + u_int bus_width); +static void ahc_construct_ppr(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo, + u_int period, u_int offset, + u_int bus_width, u_int ppr_options); +static void ahc_clear_msg_state(struct ahc_softc *ahc); +static void ahc_handle_proto_violation(struct ahc_softc *ahc); +static void ahc_handle_message_phase(struct ahc_softc *ahc); +typedef enum { + AHCMSG_1B, + AHCMSG_2B, + AHCMSG_EXT +} ahc_msgtype; +static int ahc_sent_msg(struct ahc_softc *ahc, ahc_msgtype type, + u_int msgval, int full); +static int ahc_parse_msg(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo); +static int ahc_handle_msg_reject(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo); +static void ahc_handle_ign_wide_residue(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo); +static void ahc_reinitialize_dataptrs(struct ahc_softc *ahc); +static void ahc_handle_devreset(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo, + cam_status status, char *message, + int verbose_level); +#ifdef AHC_TARGET_MODE +static void ahc_setup_target_msgin(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo, + struct scb *scb); +#endif + +static bus_dmamap_callback_t ahc_dmamap_cb; +static void ahc_build_free_scb_list(struct ahc_softc *ahc); +static int ahc_init_scbdata(struct ahc_softc *ahc); +static void ahc_fini_scbdata(struct ahc_softc *ahc); +static void ahc_qinfifo_requeue(struct ahc_softc *ahc, + struct scb *prev_scb, + struct scb *scb); +static int ahc_qinfifo_count(struct ahc_softc *ahc); +static u_int ahc_rem_scb_from_disc_list(struct ahc_softc *ahc, + u_int prev, u_int scbptr); +static void ahc_add_curscb_to_free_list(struct ahc_softc *ahc); +static u_int ahc_rem_wscb(struct ahc_softc *ahc, + u_int scbpos, u_int prev); +static void ahc_reset_current_bus(struct ahc_softc *ahc); +#ifdef AHC_DUMP_SEQ +static void ahc_dumpseq(struct ahc_softc *ahc); +#endif +static int ahc_loadseq(struct ahc_softc *ahc); +static int ahc_check_patch(struct ahc_softc *ahc, + const struct patch **start_patch, + u_int start_instr, u_int *skip_addr); +static void ahc_download_instr(struct ahc_softc *ahc, + u_int instrptr, uint8_t *dconsts); +#ifdef AHC_TARGET_MODE +static void ahc_queue_lstate_event(struct ahc_softc *ahc, + struct ahc_tmode_lstate *lstate, + u_int initiator_id, + u_int event_type, + u_int event_arg); +static void ahc_update_scsiid(struct ahc_softc *ahc, + u_int targid_mask); +static int ahc_handle_target_cmd(struct ahc_softc *ahc, + struct target_cmd *cmd); +#endif + +static u_int ahc_index_busy_tcl(struct ahc_softc *ahc, u_int tcl); +static void ahc_unbusy_tcl(struct ahc_softc *ahc, u_int tcl); +static void ahc_busy_tcl(struct ahc_softc *ahc, + u_int tcl, u_int busyid); + +/************************** SCB and SCB queue management **********************/ +static void ahc_run_untagged_queues(struct ahc_softc *ahc); +static void ahc_run_untagged_queue(struct ahc_softc *ahc, + struct scb_tailq *queue); + +/****************************** Initialization ********************************/ +static void ahc_alloc_scbs(struct ahc_softc *ahc); +static void ahc_shutdown(void *arg); + +/*************************** Interrupt Services *******************************/ +static void ahc_clear_intstat(struct ahc_softc *ahc); +static void ahc_run_qoutfifo(struct ahc_softc *ahc); +#ifdef AHC_TARGET_MODE +static void ahc_run_tqinfifo(struct ahc_softc *ahc, int paused); +#endif +static void ahc_handle_brkadrint(struct ahc_softc *ahc); +static void ahc_handle_seqint(struct ahc_softc *ahc, u_int intstat); +static void ahc_handle_scsiint(struct ahc_softc *ahc, + u_int intstat); +static void ahc_clear_critical_section(struct ahc_softc *ahc); + +/***************************** Error Recovery *********************************/ +static void ahc_freeze_devq(struct ahc_softc *ahc, struct scb *scb); +static int ahc_abort_scbs(struct ahc_softc *ahc, int target, + char channel, int lun, u_int tag, + role_t role, uint32_t status); +static void ahc_calc_residual(struct ahc_softc *ahc, + struct scb *scb); + +/*********************** Untagged Transaction Routines ************************/ +static inline void ahc_freeze_untagged_queues(struct ahc_softc *ahc); +static inline void ahc_release_untagged_queues(struct ahc_softc *ahc); + +/* + * Block our completion routine from starting the next untagged + * transaction for this target or target lun. + */ +static inline void +ahc_freeze_untagged_queues(struct ahc_softc *ahc) +{ + if ((ahc->flags & AHC_SCB_BTT) == 0) + ahc->untagged_queue_lock++; +} + +/* + * Allow the next untagged transaction for this target or target lun + * to be executed. We use a counting semaphore to allow the lock + * to be acquired recursively. Once the count drops to zero, the + * transaction queues will be run. + */ +static inline void +ahc_release_untagged_queues(struct ahc_softc *ahc) +{ + if ((ahc->flags & AHC_SCB_BTT) == 0) { + ahc->untagged_queue_lock--; + if (ahc->untagged_queue_lock == 0) + ahc_run_untagged_queues(ahc); + } +} + +/************************* Sequencer Execution Control ************************/ +/* + * Work around any chip bugs related to halting sequencer execution. + * On Ultra2 controllers, we must clear the CIOBUS stretch signal by + * reading a register that will set this signal and deassert it. + * Without this workaround, if the chip is paused, by an interrupt or + * manual pause while accessing scb ram, accesses to certain registers + * will hang the system (infinite pci retries). + */ +static void +ahc_pause_bug_fix(struct ahc_softc *ahc) +{ + if ((ahc->features & AHC_ULTRA2) != 0) + (void)ahc_inb(ahc, CCSCBCTL); +} + +/* + * Determine whether the sequencer has halted code execution. + * Returns non-zero status if the sequencer is stopped. + */ +int +ahc_is_paused(struct ahc_softc *ahc) +{ + return ((ahc_inb(ahc, HCNTRL) & PAUSE) != 0); +} + +/* + * Request that the sequencer stop and wait, indefinitely, for it + * to stop. The sequencer will only acknowledge that it is paused + * once it has reached an instruction boundary and PAUSEDIS is + * cleared in the SEQCTL register. The sequencer may use PAUSEDIS + * for critical sections. + */ +void +ahc_pause(struct ahc_softc *ahc) +{ + ahc_outb(ahc, HCNTRL, ahc->pause); + + /* + * Since the sequencer can disable pausing in a critical section, we + * must loop until it actually stops. + */ + while (ahc_is_paused(ahc) == 0) + ; + + ahc_pause_bug_fix(ahc); +} + +/* + * Allow the sequencer to continue program execution. + * We check here to ensure that no additional interrupt + * sources that would cause the sequencer to halt have been + * asserted. If, for example, a SCSI bus reset is detected + * while we are fielding a different, pausing, interrupt type, + * we don't want to release the sequencer before going back + * into our interrupt handler and dealing with this new + * condition. + */ +void +ahc_unpause(struct ahc_softc *ahc) +{ + if ((ahc_inb(ahc, INTSTAT) & (SCSIINT | SEQINT | BRKADRINT)) == 0) + ahc_outb(ahc, HCNTRL, ahc->unpause); +} + +/************************** Memory mapping routines ***************************/ +static struct ahc_dma_seg * +ahc_sg_bus_to_virt(struct scb *scb, uint32_t sg_busaddr) +{ + int sg_index; + + sg_index = (sg_busaddr - scb->sg_list_phys)/sizeof(struct ahc_dma_seg); + /* sg_list_phys points to entry 1, not 0 */ + sg_index++; + + return (&scb->sg_list[sg_index]); +} + +static uint32_t +ahc_sg_virt_to_bus(struct scb *scb, struct ahc_dma_seg *sg) +{ + int sg_index; + + /* sg_list_phys points to entry 1, not 0 */ + sg_index = sg - &scb->sg_list[1]; + + return (scb->sg_list_phys + (sg_index * sizeof(*scb->sg_list))); +} + +static uint32_t +ahc_hscb_busaddr(struct ahc_softc *ahc, u_int index) +{ + return (ahc->scb_data->hscb_busaddr + + (sizeof(struct hardware_scb) * index)); +} + +static void +ahc_sync_scb(struct ahc_softc *ahc, struct scb *scb, int op) +{ + ahc_dmamap_sync(ahc, ahc->scb_data->hscb_dmat, + ahc->scb_data->hscb_dmamap, + /*offset*/(scb->hscb - ahc->hscbs) * sizeof(*scb->hscb), + /*len*/sizeof(*scb->hscb), op); +} + +void +ahc_sync_sglist(struct ahc_softc *ahc, struct scb *scb, int op) +{ + if (scb->sg_count == 0) + return; + + ahc_dmamap_sync(ahc, ahc->scb_data->sg_dmat, scb->sg_map->sg_dmamap, + /*offset*/(scb->sg_list - scb->sg_map->sg_vaddr) + * sizeof(struct ahc_dma_seg), + /*len*/sizeof(struct ahc_dma_seg) * scb->sg_count, op); +} + +#ifdef AHC_TARGET_MODE +static uint32_t +ahc_targetcmd_offset(struct ahc_softc *ahc, u_int index) +{ + return (((uint8_t *)&ahc->targetcmds[index]) - ahc->qoutfifo); +} +#endif + +/*********************** Miscellaneous Support Functions ***********************/ +/* + * Determine whether the sequencer reported a residual + * for this SCB/transaction. + */ +static void +ahc_update_residual(struct ahc_softc *ahc, struct scb *scb) +{ + uint32_t sgptr; + + sgptr = ahc_le32toh(scb->hscb->sgptr); + if ((sgptr & SG_RESID_VALID) != 0) + ahc_calc_residual(ahc, scb); +} + +/* + * Return pointers to the transfer negotiation information + * for the specified our_id/remote_id pair. + */ +struct ahc_initiator_tinfo * +ahc_fetch_transinfo(struct ahc_softc *ahc, char channel, u_int our_id, + u_int remote_id, struct ahc_tmode_tstate **tstate) +{ + /* + * Transfer data structures are stored from the perspective + * of the target role. Since the parameters for a connection + * in the initiator role to a given target are the same as + * when the roles are reversed, we pretend we are the target. + */ + if (channel == 'B') + our_id += 8; + *tstate = ahc->enabled_targets[our_id]; + return (&(*tstate)->transinfo[remote_id]); +} + +uint16_t +ahc_inw(struct ahc_softc *ahc, u_int port) +{ + uint16_t r = ahc_inb(ahc, port+1) << 8; + return r | ahc_inb(ahc, port); +} + +void +ahc_outw(struct ahc_softc *ahc, u_int port, u_int value) +{ + ahc_outb(ahc, port, value & 0xFF); + ahc_outb(ahc, port+1, (value >> 8) & 0xFF); +} + +uint32_t +ahc_inl(struct ahc_softc *ahc, u_int port) +{ + return ((ahc_inb(ahc, port)) + | (ahc_inb(ahc, port+1) << 8) + | (ahc_inb(ahc, port+2) << 16) + | (ahc_inb(ahc, port+3) << 24)); +} + +void +ahc_outl(struct ahc_softc *ahc, u_int port, uint32_t value) +{ + ahc_outb(ahc, port, (value) & 0xFF); + ahc_outb(ahc, port+1, ((value) >> 8) & 0xFF); + ahc_outb(ahc, port+2, ((value) >> 16) & 0xFF); + ahc_outb(ahc, port+3, ((value) >> 24) & 0xFF); +} + +uint64_t +ahc_inq(struct ahc_softc *ahc, u_int port) +{ + return ((ahc_inb(ahc, port)) + | (ahc_inb(ahc, port+1) << 8) + | (ahc_inb(ahc, port+2) << 16) + | (((uint64_t)ahc_inb(ahc, port+3)) << 24) + | (((uint64_t)ahc_inb(ahc, port+4)) << 32) + | (((uint64_t)ahc_inb(ahc, port+5)) << 40) + | (((uint64_t)ahc_inb(ahc, port+6)) << 48) + | (((uint64_t)ahc_inb(ahc, port+7)) << 56)); +} + +void +ahc_outq(struct ahc_softc *ahc, u_int port, uint64_t value) +{ + ahc_outb(ahc, port, value & 0xFF); + ahc_outb(ahc, port+1, (value >> 8) & 0xFF); + ahc_outb(ahc, port+2, (value >> 16) & 0xFF); + ahc_outb(ahc, port+3, (value >> 24) & 0xFF); + ahc_outb(ahc, port+4, (value >> 32) & 0xFF); + ahc_outb(ahc, port+5, (value >> 40) & 0xFF); + ahc_outb(ahc, port+6, (value >> 48) & 0xFF); + ahc_outb(ahc, port+7, (value >> 56) & 0xFF); +} + +/* + * Get a free scb. If there are none, see if we can allocate a new SCB. + */ +struct scb * +ahc_get_scb(struct ahc_softc *ahc) +{ + struct scb *scb; + + if ((scb = SLIST_FIRST(&ahc->scb_data->free_scbs)) == NULL) { + ahc_alloc_scbs(ahc); + scb = SLIST_FIRST(&ahc->scb_data->free_scbs); + if (scb == NULL) + return (NULL); + } + SLIST_REMOVE_HEAD(&ahc->scb_data->free_scbs, links.sle); + return (scb); +} + +/* + * Return an SCB resource to the free list. + */ +void +ahc_free_scb(struct ahc_softc *ahc, struct scb *scb) +{ + struct hardware_scb *hscb; + + hscb = scb->hscb; + /* Clean up for the next user */ + ahc->scb_data->scbindex[hscb->tag] = NULL; + scb->flags = SCB_FREE; + hscb->control = 0; + + SLIST_INSERT_HEAD(&ahc->scb_data->free_scbs, scb, links.sle); + + /* Notify the OSM that a resource is now available. */ + ahc_platform_scb_free(ahc, scb); +} + +struct scb * +ahc_lookup_scb(struct ahc_softc *ahc, u_int tag) +{ + struct scb* scb; + + scb = ahc->scb_data->scbindex[tag]; + if (scb != NULL) + ahc_sync_scb(ahc, scb, + BUS_DMASYNC_POSTREAD|BUS_DMASYNC_POSTWRITE); + return (scb); +} + +static void +ahc_swap_with_next_hscb(struct ahc_softc *ahc, struct scb *scb) +{ + struct hardware_scb *q_hscb; + u_int saved_tag; + + /* + * Our queuing method is a bit tricky. The card + * knows in advance which HSCB to download, and we + * can't disappoint it. To achieve this, the next + * SCB to download is saved off in ahc->next_queued_scb. + * When we are called to queue "an arbitrary scb", + * we copy the contents of the incoming HSCB to the one + * the sequencer knows about, swap HSCB pointers and + * finally assign the SCB to the tag indexed location + * in the scb_array. This makes sure that we can still + * locate the correct SCB by SCB_TAG. + */ + q_hscb = ahc->next_queued_scb->hscb; + saved_tag = q_hscb->tag; + memcpy(q_hscb, scb->hscb, sizeof(*scb->hscb)); + if ((scb->flags & SCB_CDB32_PTR) != 0) { + q_hscb->shared_data.cdb_ptr = + ahc_htole32(ahc_hscb_busaddr(ahc, q_hscb->tag) + + offsetof(struct hardware_scb, cdb32)); + } + q_hscb->tag = saved_tag; + q_hscb->next = scb->hscb->tag; + + /* Now swap HSCB pointers. */ + ahc->next_queued_scb->hscb = scb->hscb; + scb->hscb = q_hscb; + + /* Now define the mapping from tag to SCB in the scbindex */ + ahc->scb_data->scbindex[scb->hscb->tag] = scb; +} + +/* + * Tell the sequencer about a new transaction to execute. + */ +void +ahc_queue_scb(struct ahc_softc *ahc, struct scb *scb) +{ + ahc_swap_with_next_hscb(ahc, scb); + + if (scb->hscb->tag == SCB_LIST_NULL + || scb->hscb->next == SCB_LIST_NULL) + panic("Attempt to queue invalid SCB tag %x:%x\n", + scb->hscb->tag, scb->hscb->next); + + /* + * Setup data "oddness". + */ + scb->hscb->lun &= LID; + if (ahc_get_transfer_length(scb) & 0x1) + scb->hscb->lun |= SCB_XFERLEN_ODD; + + /* + * Keep a history of SCBs we've downloaded in the qinfifo. + */ + ahc->qinfifo[ahc->qinfifonext++] = scb->hscb->tag; + + /* + * Make sure our data is consistent from the + * perspective of the adapter. + */ + ahc_sync_scb(ahc, scb, BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); + + /* Tell the adapter about the newly queued SCB */ + if ((ahc->features & AHC_QUEUE_REGS) != 0) { + ahc_outb(ahc, HNSCB_QOFF, ahc->qinfifonext); + } else { + if ((ahc->features & AHC_AUTOPAUSE) == 0) + ahc_pause(ahc); + ahc_outb(ahc, KERNEL_QINPOS, ahc->qinfifonext); + if ((ahc->features & AHC_AUTOPAUSE) == 0) + ahc_unpause(ahc); + } +} + +struct scsi_sense_data * +ahc_get_sense_buf(struct ahc_softc *ahc, struct scb *scb) +{ + int offset; + + offset = scb - ahc->scb_data->scbarray; + return (&ahc->scb_data->sense[offset]); +} + +static uint32_t +ahc_get_sense_bufaddr(struct ahc_softc *ahc, struct scb *scb) +{ + int offset; + + offset = scb - ahc->scb_data->scbarray; + return (ahc->scb_data->sense_busaddr + + (offset * sizeof(struct scsi_sense_data))); +} + +/************************** Interrupt Processing ******************************/ +static void +ahc_sync_qoutfifo(struct ahc_softc *ahc, int op) +{ + ahc_dmamap_sync(ahc, ahc->shared_data_dmat, ahc->shared_data_dmamap, + /*offset*/0, /*len*/256, op); +} + +static void +ahc_sync_tqinfifo(struct ahc_softc *ahc, int op) +{ +#ifdef AHC_TARGET_MODE + if ((ahc->flags & AHC_TARGETROLE) != 0) { + ahc_dmamap_sync(ahc, ahc->shared_data_dmat, + ahc->shared_data_dmamap, + ahc_targetcmd_offset(ahc, 0), + sizeof(struct target_cmd) * AHC_TMODE_CMDS, + op); + } +#endif +} + +/* + * See if the firmware has posted any completed commands + * into our in-core command complete fifos. + */ +#define AHC_RUN_QOUTFIFO 0x1 +#define AHC_RUN_TQINFIFO 0x2 +static u_int +ahc_check_cmdcmpltqueues(struct ahc_softc *ahc) +{ + u_int retval; + + retval = 0; + ahc_dmamap_sync(ahc, ahc->shared_data_dmat, ahc->shared_data_dmamap, + /*offset*/ahc->qoutfifonext, /*len*/1, + BUS_DMASYNC_POSTREAD); + if (ahc->qoutfifo[ahc->qoutfifonext] != SCB_LIST_NULL) + retval |= AHC_RUN_QOUTFIFO; +#ifdef AHC_TARGET_MODE + if ((ahc->flags & AHC_TARGETROLE) != 0 + && (ahc->flags & AHC_TQINFIFO_BLOCKED) == 0) { + ahc_dmamap_sync(ahc, ahc->shared_data_dmat, + ahc->shared_data_dmamap, + ahc_targetcmd_offset(ahc, ahc->tqinfifofnext), + /*len*/sizeof(struct target_cmd), + BUS_DMASYNC_POSTREAD); + if (ahc->targetcmds[ahc->tqinfifonext].cmd_valid != 0) + retval |= AHC_RUN_TQINFIFO; + } +#endif + return (retval); +} + +/* + * Catch an interrupt from the adapter + */ +int +ahc_intr(struct ahc_softc *ahc) +{ + u_int intstat; + + if ((ahc->pause & INTEN) == 0) { + /* + * Our interrupt is not enabled on the chip + * and may be disabled for re-entrancy reasons, + * so just return. This is likely just a shared + * interrupt. + */ + return (0); + } + /* + * Instead of directly reading the interrupt status register, + * infer the cause of the interrupt by checking our in-core + * completion queues. This avoids a costly PCI bus read in + * most cases. + */ + if ((ahc->flags & (AHC_ALL_INTERRUPTS|AHC_EDGE_INTERRUPT)) == 0 + && (ahc_check_cmdcmpltqueues(ahc) != 0)) + intstat = CMDCMPLT; + else { + intstat = ahc_inb(ahc, INTSTAT); + } + + if ((intstat & INT_PEND) == 0) { +#if AHC_PCI_CONFIG > 0 + if (ahc->unsolicited_ints > 500) { + ahc->unsolicited_ints = 0; + if ((ahc->chip & AHC_PCI) != 0 + && (ahc_inb(ahc, ERROR) & PCIERRSTAT) != 0) + ahc->bus_intr(ahc); + } +#endif + ahc->unsolicited_ints++; + return (0); + } + ahc->unsolicited_ints = 0; + + if (intstat & CMDCMPLT) { + ahc_outb(ahc, CLRINT, CLRCMDINT); + + /* + * Ensure that the chip sees that we've cleared + * this interrupt before we walk the output fifo. + * Otherwise, we may, due to posted bus writes, + * clear the interrupt after we finish the scan, + * and after the sequencer has added new entries + * and asserted the interrupt again. + */ + ahc_flush_device_writes(ahc); + ahc_run_qoutfifo(ahc); +#ifdef AHC_TARGET_MODE + if ((ahc->flags & AHC_TARGETROLE) != 0) + ahc_run_tqinfifo(ahc, /*paused*/FALSE); +#endif + } + + /* + * Handle statuses that may invalidate our cached + * copy of INTSTAT separately. + */ + if (intstat == 0xFF && (ahc->features & AHC_REMOVABLE) != 0) { + /* Hot eject. Do nothing */ + } else if (intstat & BRKADRINT) { + ahc_handle_brkadrint(ahc); + } else if ((intstat & (SEQINT|SCSIINT)) != 0) { + + ahc_pause_bug_fix(ahc); + + if ((intstat & SEQINT) != 0) + ahc_handle_seqint(ahc, intstat); + + if ((intstat & SCSIINT) != 0) + ahc_handle_scsiint(ahc, intstat); + } + return (1); +} + +/************************* Sequencer Execution Control ************************/ +/* + * Restart the sequencer program from address zero + */ +static void +ahc_restart(struct ahc_softc *ahc) +{ + uint8_t sblkctl; + + ahc_pause(ahc); + + /* No more pending messages. */ + ahc_clear_msg_state(ahc); + + ahc_outb(ahc, SCSISIGO, 0); /* De-assert BSY */ + ahc_outb(ahc, MSG_OUT, MSG_NOOP); /* No message to send */ + ahc_outb(ahc, SXFRCTL1, ahc_inb(ahc, SXFRCTL1) & ~BITBUCKET); + ahc_outb(ahc, LASTPHASE, P_BUSFREE); + ahc_outb(ahc, SAVED_SCSIID, 0xFF); + ahc_outb(ahc, SAVED_LUN, 0xFF); + + /* + * Ensure that the sequencer's idea of TQINPOS + * matches our own. The sequencer increments TQINPOS + * only after it sees a DMA complete and a reset could + * occur before the increment leaving the kernel to believe + * the command arrived but the sequencer to not. + */ + ahc_outb(ahc, TQINPOS, ahc->tqinfifonext); + + /* Always allow reselection */ + ahc_outb(ahc, SCSISEQ, + ahc_inb(ahc, SCSISEQ_TEMPLATE) & (ENSELI|ENRSELI|ENAUTOATNP)); + if ((ahc->features & AHC_CMD_CHAN) != 0) { + /* Ensure that no DMA operations are in progress */ + ahc_outb(ahc, CCSCBCNT, 0); + ahc_outb(ahc, CCSGCTL, 0); + ahc_outb(ahc, CCSCBCTL, 0); + } + /* + * If we were in the process of DMA'ing SCB data into + * an SCB, replace that SCB on the free list. This prevents + * an SCB leak. + */ + if ((ahc_inb(ahc, SEQ_FLAGS2) & SCB_DMA) != 0) { + ahc_add_curscb_to_free_list(ahc); + ahc_outb(ahc, SEQ_FLAGS2, + ahc_inb(ahc, SEQ_FLAGS2) & ~SCB_DMA); + } + + /* + * Clear any pending sequencer interrupt. It is no + * longer relevant since we're resetting the Program + * Counter. + */ + ahc_outb(ahc, CLRINT, CLRSEQINT); + + ahc_outb(ahc, MWI_RESIDUAL, 0); + ahc_outb(ahc, SEQCTL, ahc->seqctl); + ahc_outb(ahc, SEQADDR0, 0); + ahc_outb(ahc, SEQADDR1, 0); + + /* + * Take the LED out of diagnostic mode on PM resume, too + */ + sblkctl = ahc_inb(ahc, SBLKCTL); + ahc_outb(ahc, SBLKCTL, (sblkctl & ~(DIAGLEDEN|DIAGLEDON))); + + ahc_unpause(ahc); +} + +/************************* Input/Output Queues ********************************/ +static void +ahc_run_qoutfifo(struct ahc_softc *ahc) +{ + struct scb *scb; + u_int scb_index; + + ahc_sync_qoutfifo(ahc, BUS_DMASYNC_POSTREAD); + while (ahc->qoutfifo[ahc->qoutfifonext] != SCB_LIST_NULL) { + + scb_index = ahc->qoutfifo[ahc->qoutfifonext]; + if ((ahc->qoutfifonext & 0x03) == 0x03) { + u_int modnext; + + /* + * Clear 32bits of QOUTFIFO at a time + * so that we don't clobber an incoming + * byte DMA to the array on architectures + * that only support 32bit load and store + * operations. + */ + modnext = ahc->qoutfifonext & ~0x3; + *((uint32_t *)(&ahc->qoutfifo[modnext])) = 0xFFFFFFFFUL; + ahc_dmamap_sync(ahc, ahc->shared_data_dmat, + ahc->shared_data_dmamap, + /*offset*/modnext, /*len*/4, + BUS_DMASYNC_PREREAD); + } + ahc->qoutfifonext++; + + scb = ahc_lookup_scb(ahc, scb_index); + if (scb == NULL) { + printk("%s: WARNING no command for scb %d " + "(cmdcmplt)\nQOUTPOS = %d\n", + ahc_name(ahc), scb_index, + (ahc->qoutfifonext - 1) & 0xFF); + continue; + } + + /* + * Save off the residual + * if there is one. + */ + ahc_update_residual(ahc, scb); + ahc_done(ahc, scb); + } +} + +static void +ahc_run_untagged_queues(struct ahc_softc *ahc) +{ + int i; + + for (i = 0; i < 16; i++) + ahc_run_untagged_queue(ahc, &ahc->untagged_queues[i]); +} + +static void +ahc_run_untagged_queue(struct ahc_softc *ahc, struct scb_tailq *queue) +{ + struct scb *scb; + + if (ahc->untagged_queue_lock != 0) + return; + + if ((scb = TAILQ_FIRST(queue)) != NULL + && (scb->flags & SCB_ACTIVE) == 0) { + scb->flags |= SCB_ACTIVE; + ahc_queue_scb(ahc, scb); + } +} + +/************************* Interrupt Handling *********************************/ +static void +ahc_handle_brkadrint(struct ahc_softc *ahc) +{ + /* + * We upset the sequencer :-( + * Lookup the error message + */ + int i; + int error; + + error = ahc_inb(ahc, ERROR); + for (i = 0; error != 1 && i < num_errors; i++) + error >>= 1; + printk("%s: brkadrint, %s at seqaddr = 0x%x\n", + ahc_name(ahc), ahc_hard_errors[i].errmesg, + ahc_inb(ahc, SEQADDR0) | + (ahc_inb(ahc, SEQADDR1) << 8)); + + ahc_dump_card_state(ahc); + + /* Tell everyone that this HBA is no longer available */ + ahc_abort_scbs(ahc, CAM_TARGET_WILDCARD, ALL_CHANNELS, + CAM_LUN_WILDCARD, SCB_LIST_NULL, ROLE_UNKNOWN, + CAM_NO_HBA); + + /* Disable all interrupt sources by resetting the controller */ + ahc_shutdown(ahc); +} + +static void +ahc_handle_seqint(struct ahc_softc *ahc, u_int intstat) +{ + struct scb *scb; + struct ahc_devinfo devinfo; + + ahc_fetch_devinfo(ahc, &devinfo); + + /* + * Clear the upper byte that holds SEQINT status + * codes and clear the SEQINT bit. We will unpause + * the sequencer, if appropriate, after servicing + * the request. + */ + ahc_outb(ahc, CLRINT, CLRSEQINT); + switch (intstat & SEQINT_MASK) { + case BAD_STATUS: + { + u_int scb_index; + struct hardware_scb *hscb; + + /* + * Set the default return value to 0 (don't + * send sense). The sense code will change + * this if needed. + */ + ahc_outb(ahc, RETURN_1, 0); + + /* + * The sequencer will notify us when a command + * has an error that would be of interest to + * the kernel. This allows us to leave the sequencer + * running in the common case of command completes + * without error. The sequencer will already have + * dma'd the SCB back up to us, so we can reference + * the in kernel copy directly. + */ + scb_index = ahc_inb(ahc, SCB_TAG); + scb = ahc_lookup_scb(ahc, scb_index); + if (scb == NULL) { + ahc_print_devinfo(ahc, &devinfo); + printk("ahc_intr - referenced scb " + "not valid during seqint 0x%x scb(%d)\n", + intstat, scb_index); + ahc_dump_card_state(ahc); + panic("for safety"); + goto unpause; + } + + hscb = scb->hscb; + + /* Don't want to clobber the original sense code */ + if ((scb->flags & SCB_SENSE) != 0) { + /* + * Clear the SCB_SENSE Flag and have + * the sequencer do a normal command + * complete. + */ + scb->flags &= ~SCB_SENSE; + ahc_set_transaction_status(scb, CAM_AUTOSENSE_FAIL); + break; + } + ahc_set_transaction_status(scb, CAM_SCSI_STATUS_ERROR); + /* Freeze the queue until the client sees the error. */ + ahc_freeze_devq(ahc, scb); + ahc_freeze_scb(scb); + ahc_set_scsi_status(scb, hscb->shared_data.status.scsi_status); + switch (hscb->shared_data.status.scsi_status) { + case SCSI_STATUS_OK: + printk("%s: Interrupted for status of 0???\n", + ahc_name(ahc)); + break; + case SCSI_STATUS_CMD_TERMINATED: + case SCSI_STATUS_CHECK_COND: + { + struct ahc_dma_seg *sg; + struct scsi_sense *sc; + struct ahc_initiator_tinfo *targ_info; + struct ahc_tmode_tstate *tstate; + struct ahc_transinfo *tinfo; +#ifdef AHC_DEBUG + if (ahc_debug & AHC_SHOW_SENSE) { + ahc_print_path(ahc, scb); + printk("SCB %d: requests Check Status\n", + scb->hscb->tag); + } +#endif + + if (ahc_perform_autosense(scb) == 0) + break; + + targ_info = ahc_fetch_transinfo(ahc, + devinfo.channel, + devinfo.our_scsiid, + devinfo.target, + &tstate); + tinfo = &targ_info->curr; + sg = scb->sg_list; + sc = (struct scsi_sense *)(&hscb->shared_data.cdb); + /* + * Save off the residual if there is one. + */ + ahc_update_residual(ahc, scb); +#ifdef AHC_DEBUG + if (ahc_debug & AHC_SHOW_SENSE) { + ahc_print_path(ahc, scb); + printk("Sending Sense\n"); + } +#endif + sg->addr = ahc_get_sense_bufaddr(ahc, scb); + sg->len = ahc_get_sense_bufsize(ahc, scb); + sg->len |= AHC_DMA_LAST_SEG; + + /* Fixup byte order */ + sg->addr = ahc_htole32(sg->addr); + sg->len = ahc_htole32(sg->len); + + sc->opcode = REQUEST_SENSE; + sc->byte2 = 0; + if (tinfo->protocol_version <= SCSI_REV_2 + && SCB_GET_LUN(scb) < 8) + sc->byte2 = SCB_GET_LUN(scb) << 5; + sc->unused[0] = 0; + sc->unused[1] = 0; + sc->length = sg->len; + sc->control = 0; + + /* + * We can't allow the target to disconnect. + * This will be an untagged transaction and + * having the target disconnect will make this + * transaction indestinguishable from outstanding + * tagged transactions. + */ + hscb->control = 0; + + /* + * This request sense could be because the + * the device lost power or in some other + * way has lost our transfer negotiations. + * Renegotiate if appropriate. Unit attention + * errors will be reported before any data + * phases occur. + */ + if (ahc_get_residual(scb) + == ahc_get_transfer_length(scb)) { + ahc_update_neg_request(ahc, &devinfo, + tstate, targ_info, + AHC_NEG_IF_NON_ASYNC); + } + if (tstate->auto_negotiate & devinfo.target_mask) { + hscb->control |= MK_MESSAGE; + scb->flags &= ~SCB_NEGOTIATE; + scb->flags |= SCB_AUTO_NEGOTIATE; + } + hscb->cdb_len = sizeof(*sc); + hscb->dataptr = sg->addr; + hscb->datacnt = sg->len; + hscb->sgptr = scb->sg_list_phys | SG_FULL_RESID; + hscb->sgptr = ahc_htole32(hscb->sgptr); + scb->sg_count = 1; + scb->flags |= SCB_SENSE; + ahc_qinfifo_requeue_tail(ahc, scb); + ahc_outb(ahc, RETURN_1, SEND_SENSE); + /* + * Ensure we have enough time to actually + * retrieve the sense. + */ + ahc_scb_timer_reset(scb, 5 * 1000000); + break; + } + default: + break; + } + break; + } + case NO_MATCH: + { + /* Ensure we don't leave the selection hardware on */ + ahc_outb(ahc, SCSISEQ, + ahc_inb(ahc, SCSISEQ) & (ENSELI|ENRSELI|ENAUTOATNP)); + + printk("%s:%c:%d: no active SCB for reconnecting " + "target - issuing BUS DEVICE RESET\n", + ahc_name(ahc), devinfo.channel, devinfo.target); + printk("SAVED_SCSIID == 0x%x, SAVED_LUN == 0x%x, " + "ARG_1 == 0x%x ACCUM = 0x%x\n", + ahc_inb(ahc, SAVED_SCSIID), ahc_inb(ahc, SAVED_LUN), + ahc_inb(ahc, ARG_1), ahc_inb(ahc, ACCUM)); + printk("SEQ_FLAGS == 0x%x, SCBPTR == 0x%x, BTT == 0x%x, " + "SINDEX == 0x%x\n", + ahc_inb(ahc, SEQ_FLAGS), ahc_inb(ahc, SCBPTR), + ahc_index_busy_tcl(ahc, + BUILD_TCL(ahc_inb(ahc, SAVED_SCSIID), + ahc_inb(ahc, SAVED_LUN))), + ahc_inb(ahc, SINDEX)); + printk("SCSIID == 0x%x, SCB_SCSIID == 0x%x, SCB_LUN == 0x%x, " + "SCB_TAG == 0x%x, SCB_CONTROL == 0x%x\n", + ahc_inb(ahc, SCSIID), ahc_inb(ahc, SCB_SCSIID), + ahc_inb(ahc, SCB_LUN), ahc_inb(ahc, SCB_TAG), + ahc_inb(ahc, SCB_CONTROL)); + printk("SCSIBUSL == 0x%x, SCSISIGI == 0x%x\n", + ahc_inb(ahc, SCSIBUSL), ahc_inb(ahc, SCSISIGI)); + printk("SXFRCTL0 == 0x%x\n", ahc_inb(ahc, SXFRCTL0)); + printk("SEQCTL == 0x%x\n", ahc_inb(ahc, SEQCTL)); + ahc_dump_card_state(ahc); + ahc->msgout_buf[0] = MSG_BUS_DEV_RESET; + ahc->msgout_len = 1; + ahc->msgout_index = 0; + ahc->msg_type = MSG_TYPE_INITIATOR_MSGOUT; + ahc_outb(ahc, MSG_OUT, HOST_MSG); + ahc_assert_atn(ahc); + break; + } + case SEND_REJECT: + { + u_int rejbyte = ahc_inb(ahc, ACCUM); + printk("%s:%c:%d: Warning - unknown message received from " + "target (0x%x). Rejecting\n", + ahc_name(ahc), devinfo.channel, devinfo.target, rejbyte); + break; + } + case PROTO_VIOLATION: + { + ahc_handle_proto_violation(ahc); + break; + } + case IGN_WIDE_RES: + ahc_handle_ign_wide_residue(ahc, &devinfo); + break; + case PDATA_REINIT: + ahc_reinitialize_dataptrs(ahc); + break; + case BAD_PHASE: + { + u_int lastphase; + + lastphase = ahc_inb(ahc, LASTPHASE); + printk("%s:%c:%d: unknown scsi bus phase %x, " + "lastphase = 0x%x. Attempting to continue\n", + ahc_name(ahc), devinfo.channel, devinfo.target, + lastphase, ahc_inb(ahc, SCSISIGI)); + break; + } + case MISSED_BUSFREE: + { + u_int lastphase; + + lastphase = ahc_inb(ahc, LASTPHASE); + printk("%s:%c:%d: Missed busfree. " + "Lastphase = 0x%x, Curphase = 0x%x\n", + ahc_name(ahc), devinfo.channel, devinfo.target, + lastphase, ahc_inb(ahc, SCSISIGI)); + ahc_restart(ahc); + return; + } + case HOST_MSG_LOOP: + { + /* + * The sequencer has encountered a message phase + * that requires host assistance for completion. + * While handling the message phase(s), we will be + * notified by the sequencer after each byte is + * transferred so we can track bus phase changes. + * + * If this is the first time we've seen a HOST_MSG_LOOP + * interrupt, initialize the state of the host message + * loop. + */ + if (ahc->msg_type == MSG_TYPE_NONE) { + struct scb *scb; + u_int scb_index; + u_int bus_phase; + + bus_phase = ahc_inb(ahc, SCSISIGI) & PHASE_MASK; + if (bus_phase != P_MESGIN + && bus_phase != P_MESGOUT) { + printk("ahc_intr: HOST_MSG_LOOP bad " + "phase 0x%x\n", + bus_phase); + /* + * Probably transitioned to bus free before + * we got here. Just punt the message. + */ + ahc_clear_intstat(ahc); + ahc_restart(ahc); + return; + } + + scb_index = ahc_inb(ahc, SCB_TAG); + scb = ahc_lookup_scb(ahc, scb_index); + if (devinfo.role == ROLE_INITIATOR) { + if (bus_phase == P_MESGOUT) { + if (scb == NULL) + panic("HOST_MSG_LOOP with " + "invalid SCB %x\n", + scb_index); + + ahc_setup_initiator_msgout(ahc, + &devinfo, + scb); + } else { + ahc->msg_type = + MSG_TYPE_INITIATOR_MSGIN; + ahc->msgin_index = 0; + } + } +#ifdef AHC_TARGET_MODE + else { + if (bus_phase == P_MESGOUT) { + ahc->msg_type = + MSG_TYPE_TARGET_MSGOUT; + ahc->msgin_index = 0; + } + else + ahc_setup_target_msgin(ahc, + &devinfo, + scb); + } +#endif + } + + ahc_handle_message_phase(ahc); + break; + } + case PERR_DETECTED: + { + /* + * If we've cleared the parity error interrupt + * but the sequencer still believes that SCSIPERR + * is true, it must be that the parity error is + * for the currently presented byte on the bus, + * and we are not in a phase (data-in) where we will + * eventually ack this byte. Ack the byte and + * throw it away in the hope that the target will + * take us to message out to deliver the appropriate + * error message. + */ + if ((intstat & SCSIINT) == 0 + && (ahc_inb(ahc, SSTAT1) & SCSIPERR) != 0) { + + if ((ahc->features & AHC_DT) == 0) { + u_int curphase; + + /* + * The hardware will only let you ack bytes + * if the expected phase in SCSISIGO matches + * the current phase. Make sure this is + * currently the case. + */ + curphase = ahc_inb(ahc, SCSISIGI) & PHASE_MASK; + ahc_outb(ahc, LASTPHASE, curphase); + ahc_outb(ahc, SCSISIGO, curphase); + } + if ((ahc_inb(ahc, SCSISIGI) & (CDI|MSGI)) == 0) { + int wait; + + /* + * In a data phase. Faster to bitbucket + * the data than to individually ack each + * byte. This is also the only strategy + * that will work with AUTOACK enabled. + */ + ahc_outb(ahc, SXFRCTL1, + ahc_inb(ahc, SXFRCTL1) | BITBUCKET); + wait = 5000; + while (--wait != 0) { + if ((ahc_inb(ahc, SCSISIGI) + & (CDI|MSGI)) != 0) + break; + ahc_delay(100); + } + ahc_outb(ahc, SXFRCTL1, + ahc_inb(ahc, SXFRCTL1) & ~BITBUCKET); + if (wait == 0) { + struct scb *scb; + u_int scb_index; + + ahc_print_devinfo(ahc, &devinfo); + printk("Unable to clear parity error. " + "Resetting bus.\n"); + scb_index = ahc_inb(ahc, SCB_TAG); + scb = ahc_lookup_scb(ahc, scb_index); + if (scb != NULL) + ahc_set_transaction_status(scb, + CAM_UNCOR_PARITY); + ahc_reset_channel(ahc, devinfo.channel, + /*init reset*/TRUE); + } + } else { + ahc_inb(ahc, SCSIDATL); + } + } + break; + } + case DATA_OVERRUN: + { + /* + * When the sequencer detects an overrun, it + * places the controller in "BITBUCKET" mode + * and allows the target to complete its transfer. + * Unfortunately, none of the counters get updated + * when the controller is in this mode, so we have + * no way of knowing how large the overrun was. + */ + u_int scbindex = ahc_inb(ahc, SCB_TAG); + u_int lastphase = ahc_inb(ahc, LASTPHASE); + u_int i; + + scb = ahc_lookup_scb(ahc, scbindex); + for (i = 0; i < num_phases; i++) { + if (lastphase == ahc_phase_table[i].phase) + break; + } + ahc_print_path(ahc, scb); + printk("data overrun detected %s." + " Tag == 0x%x.\n", + ahc_phase_table[i].phasemsg, + scb->hscb->tag); + ahc_print_path(ahc, scb); + printk("%s seen Data Phase. Length = %ld. NumSGs = %d.\n", + ahc_inb(ahc, SEQ_FLAGS) & DPHASE ? "Have" : "Haven't", + ahc_get_transfer_length(scb), scb->sg_count); + if (scb->sg_count > 0) { + for (i = 0; i < scb->sg_count; i++) { + + printk("sg[%d] - Addr 0x%x%x : Length %d\n", + i, + (ahc_le32toh(scb->sg_list[i].len) >> 24 + & SG_HIGH_ADDR_BITS), + ahc_le32toh(scb->sg_list[i].addr), + ahc_le32toh(scb->sg_list[i].len) + & AHC_SG_LEN_MASK); + } + } + /* + * Set this and it will take effect when the + * target does a command complete. + */ + ahc_freeze_devq(ahc, scb); + if ((scb->flags & SCB_SENSE) == 0) { + ahc_set_transaction_status(scb, CAM_DATA_RUN_ERR); + } else { + scb->flags &= ~SCB_SENSE; + ahc_set_transaction_status(scb, CAM_AUTOSENSE_FAIL); + } + ahc_freeze_scb(scb); + + if ((ahc->features & AHC_ULTRA2) != 0) { + /* + * Clear the channel in case we return + * to data phase later. + */ + ahc_outb(ahc, SXFRCTL0, + ahc_inb(ahc, SXFRCTL0) | CLRSTCNT|CLRCHN); + ahc_outb(ahc, SXFRCTL0, + ahc_inb(ahc, SXFRCTL0) | CLRSTCNT|CLRCHN); + } + if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) { + u_int dscommand1; + + /* Ensure HHADDR is 0 for future DMA operations. */ + dscommand1 = ahc_inb(ahc, DSCOMMAND1); + ahc_outb(ahc, DSCOMMAND1, dscommand1 | HADDLDSEL0); + ahc_outb(ahc, HADDR, 0); + ahc_outb(ahc, DSCOMMAND1, dscommand1); + } + break; + } + case MKMSG_FAILED: + { + u_int scbindex; + + printk("%s:%c:%d:%d: Attempt to issue message failed\n", + ahc_name(ahc), devinfo.channel, devinfo.target, + devinfo.lun); + scbindex = ahc_inb(ahc, SCB_TAG); + scb = ahc_lookup_scb(ahc, scbindex); + if (scb != NULL + && (scb->flags & SCB_RECOVERY_SCB) != 0) + /* + * Ensure that we didn't put a second instance of this + * SCB into the QINFIFO. + */ + ahc_search_qinfifo(ahc, SCB_GET_TARGET(ahc, scb), + SCB_GET_CHANNEL(ahc, scb), + SCB_GET_LUN(scb), scb->hscb->tag, + ROLE_INITIATOR, /*status*/0, + SEARCH_REMOVE); + break; + } + case NO_FREE_SCB: + { + printk("%s: No free or disconnected SCBs\n", ahc_name(ahc)); + ahc_dump_card_state(ahc); + panic("for safety"); + break; + } + case SCB_MISMATCH: + { + u_int scbptr; + + scbptr = ahc_inb(ahc, SCBPTR); + printk("Bogus TAG after DMA. SCBPTR %d, tag %d, our tag %d\n", + scbptr, ahc_inb(ahc, ARG_1), + ahc->scb_data->hscbs[scbptr].tag); + ahc_dump_card_state(ahc); + panic("for safety"); + break; + } + case OUT_OF_RANGE: + { + printk("%s: BTT calculation out of range\n", ahc_name(ahc)); + printk("SAVED_SCSIID == 0x%x, SAVED_LUN == 0x%x, " + "ARG_1 == 0x%x ACCUM = 0x%x\n", + ahc_inb(ahc, SAVED_SCSIID), ahc_inb(ahc, SAVED_LUN), + ahc_inb(ahc, ARG_1), ahc_inb(ahc, ACCUM)); + printk("SEQ_FLAGS == 0x%x, SCBPTR == 0x%x, BTT == 0x%x, " + "SINDEX == 0x%x\n, A == 0x%x\n", + ahc_inb(ahc, SEQ_FLAGS), ahc_inb(ahc, SCBPTR), + ahc_index_busy_tcl(ahc, + BUILD_TCL(ahc_inb(ahc, SAVED_SCSIID), + ahc_inb(ahc, SAVED_LUN))), + ahc_inb(ahc, SINDEX), + ahc_inb(ahc, ACCUM)); + printk("SCSIID == 0x%x, SCB_SCSIID == 0x%x, SCB_LUN == 0x%x, " + "SCB_TAG == 0x%x, SCB_CONTROL == 0x%x\n", + ahc_inb(ahc, SCSIID), ahc_inb(ahc, SCB_SCSIID), + ahc_inb(ahc, SCB_LUN), ahc_inb(ahc, SCB_TAG), + ahc_inb(ahc, SCB_CONTROL)); + printk("SCSIBUSL == 0x%x, SCSISIGI == 0x%x\n", + ahc_inb(ahc, SCSIBUSL), ahc_inb(ahc, SCSISIGI)); + ahc_dump_card_state(ahc); + panic("for safety"); + break; + } + default: + printk("ahc_intr: seqint, " + "intstat == 0x%x, scsisigi = 0x%x\n", + intstat, ahc_inb(ahc, SCSISIGI)); + break; + } +unpause: + /* + * The sequencer is paused immediately on + * a SEQINT, so we should restart it when + * we're done. + */ + ahc_unpause(ahc); +} + +static void +ahc_handle_scsiint(struct ahc_softc *ahc, u_int intstat) +{ + u_int scb_index; + u_int status0; + u_int status; + struct scb *scb; + char cur_channel; + char intr_channel; + + if ((ahc->features & AHC_TWIN) != 0 + && ((ahc_inb(ahc, SBLKCTL) & SELBUSB) != 0)) + cur_channel = 'B'; + else + cur_channel = 'A'; + intr_channel = cur_channel; + + if ((ahc->features & AHC_ULTRA2) != 0) + status0 = ahc_inb(ahc, SSTAT0) & IOERR; + else + status0 = 0; + status = ahc_inb(ahc, SSTAT1) & (SELTO|SCSIRSTI|BUSFREE|SCSIPERR); + if (status == 0 && status0 == 0) { + if ((ahc->features & AHC_TWIN) != 0) { + /* Try the other channel */ + ahc_outb(ahc, SBLKCTL, ahc_inb(ahc, SBLKCTL) ^ SELBUSB); + status = ahc_inb(ahc, SSTAT1) + & (SELTO|SCSIRSTI|BUSFREE|SCSIPERR); + intr_channel = (cur_channel == 'A') ? 'B' : 'A'; + } + if (status == 0) { + printk("%s: Spurious SCSI interrupt\n", ahc_name(ahc)); + ahc_outb(ahc, CLRINT, CLRSCSIINT); + ahc_unpause(ahc); + return; + } + } + + /* Make sure the sequencer is in a safe location. */ + ahc_clear_critical_section(ahc); + + scb_index = ahc_inb(ahc, SCB_TAG); + scb = ahc_lookup_scb(ahc, scb_index); + if (scb != NULL + && (ahc_inb(ahc, SEQ_FLAGS) & NOT_IDENTIFIED) != 0) + scb = NULL; + + if ((ahc->features & AHC_ULTRA2) != 0 + && (status0 & IOERR) != 0) { + int now_lvd; + + now_lvd = ahc_inb(ahc, SBLKCTL) & ENAB40; + printk("%s: Transceiver State Has Changed to %s mode\n", + ahc_name(ahc), now_lvd ? "LVD" : "SE"); + ahc_outb(ahc, CLRSINT0, CLRIOERR); + /* + * When transitioning to SE mode, the reset line + * glitches, triggering an arbitration bug in some + * Ultra2 controllers. This bug is cleared when we + * assert the reset line. Since a reset glitch has + * already occurred with this transition and a + * transceiver state change is handled just like + * a bus reset anyway, asserting the reset line + * ourselves is safe. + */ + ahc_reset_channel(ahc, intr_channel, + /*Initiate Reset*/now_lvd == 0); + } else if ((status & SCSIRSTI) != 0) { + printk("%s: Someone reset channel %c\n", + ahc_name(ahc), intr_channel); + if (intr_channel != cur_channel) + ahc_outb(ahc, SBLKCTL, ahc_inb(ahc, SBLKCTL) ^ SELBUSB); + ahc_reset_channel(ahc, intr_channel, /*Initiate Reset*/FALSE); + } else if ((status & SCSIPERR) != 0) { + /* + * Determine the bus phase and queue an appropriate message. + * SCSIPERR is latched true as soon as a parity error + * occurs. If the sequencer acked the transfer that + * caused the parity error and the currently presented + * transfer on the bus has correct parity, SCSIPERR will + * be cleared by CLRSCSIPERR. Use this to determine if + * we should look at the last phase the sequencer recorded, + * or the current phase presented on the bus. + */ + struct ahc_devinfo devinfo; + u_int mesg_out; + u_int curphase; + u_int errorphase; + u_int lastphase; + u_int scsirate; + u_int i; + u_int sstat2; + int silent; + + lastphase = ahc_inb(ahc, LASTPHASE); + curphase = ahc_inb(ahc, SCSISIGI) & PHASE_MASK; + sstat2 = ahc_inb(ahc, SSTAT2); + ahc_outb(ahc, CLRSINT1, CLRSCSIPERR); + /* + * For all phases save DATA, the sequencer won't + * automatically ack a byte that has a parity error + * in it. So the only way that the current phase + * could be 'data-in' is if the parity error is for + * an already acked byte in the data phase. During + * synchronous data-in transfers, we may actually + * ack bytes before latching the current phase in + * LASTPHASE, leading to the discrepancy between + * curphase and lastphase. + */ + if ((ahc_inb(ahc, SSTAT1) & SCSIPERR) != 0 + || curphase == P_DATAIN || curphase == P_DATAIN_DT) + errorphase = curphase; + else + errorphase = lastphase; + + for (i = 0; i < num_phases; i++) { + if (errorphase == ahc_phase_table[i].phase) + break; + } + mesg_out = ahc_phase_table[i].mesg_out; + silent = FALSE; + if (scb != NULL) { + if (SCB_IS_SILENT(scb)) + silent = TRUE; + else + ahc_print_path(ahc, scb); + scb->flags |= SCB_TRANSMISSION_ERROR; + } else + printk("%s:%c:%d: ", ahc_name(ahc), intr_channel, + SCSIID_TARGET(ahc, ahc_inb(ahc, SAVED_SCSIID))); + scsirate = ahc_inb(ahc, SCSIRATE); + if (silent == FALSE) { + printk("parity error detected %s. " + "SEQADDR(0x%x) SCSIRATE(0x%x)\n", + ahc_phase_table[i].phasemsg, + ahc_inw(ahc, SEQADDR0), + scsirate); + if ((ahc->features & AHC_DT) != 0) { + if ((sstat2 & CRCVALERR) != 0) + printk("\tCRC Value Mismatch\n"); + if ((sstat2 & CRCENDERR) != 0) + printk("\tNo terminal CRC packet " + "received\n"); + if ((sstat2 & CRCREQERR) != 0) + printk("\tIllegal CRC packet " + "request\n"); + if ((sstat2 & DUAL_EDGE_ERR) != 0) + printk("\tUnexpected %sDT Data Phase\n", + (scsirate & SINGLE_EDGE) + ? "" : "non-"); + } + } + + if ((ahc->features & AHC_DT) != 0 + && (sstat2 & DUAL_EDGE_ERR) != 0) { + /* + * This error applies regardless of + * data direction, so ignore the value + * in the phase table. + */ + mesg_out = MSG_INITIATOR_DET_ERR; + } + + /* + * We've set the hardware to assert ATN if we + * get a parity error on "in" phases, so all we + * need to do is stuff the message buffer with + * the appropriate message. "In" phases have set + * mesg_out to something other than MSG_NOP. + */ + if (mesg_out != MSG_NOOP) { + if (ahc->msg_type != MSG_TYPE_NONE) + ahc->send_msg_perror = TRUE; + else + ahc_outb(ahc, MSG_OUT, mesg_out); + } + /* + * Force a renegotiation with this target just in + * case we are out of sync for some external reason + * unknown (or unreported) by the target. + */ + ahc_fetch_devinfo(ahc, &devinfo); + ahc_force_renegotiation(ahc, &devinfo); + + ahc_outb(ahc, CLRINT, CLRSCSIINT); + ahc_unpause(ahc); + } else if ((status & SELTO) != 0) { + u_int scbptr; + + /* Stop the selection */ + ahc_outb(ahc, SCSISEQ, 0); + + /* No more pending messages */ + ahc_clear_msg_state(ahc); + + /* Clear interrupt state */ + ahc_outb(ahc, SIMODE1, ahc_inb(ahc, SIMODE1) & ~ENBUSFREE); + ahc_outb(ahc, CLRSINT1, CLRSELTIMEO|CLRBUSFREE|CLRSCSIPERR); + + /* + * Although the driver does not care about the + * 'Selection in Progress' status bit, the busy + * LED does. SELINGO is only cleared by a successful + * selection, so we must manually clear it to insure + * the LED turns off just incase no future successful + * selections occur (e.g. no devices on the bus). + */ + ahc_outb(ahc, CLRSINT0, CLRSELINGO); + + scbptr = ahc_inb(ahc, WAITING_SCBH); + ahc_outb(ahc, SCBPTR, scbptr); + scb_index = ahc_inb(ahc, SCB_TAG); + + scb = ahc_lookup_scb(ahc, scb_index); + if (scb == NULL) { + printk("%s: ahc_intr - referenced scb not " + "valid during SELTO scb(%d, %d)\n", + ahc_name(ahc), scbptr, scb_index); + ahc_dump_card_state(ahc); + } else { + struct ahc_devinfo devinfo; +#ifdef AHC_DEBUG + if ((ahc_debug & AHC_SHOW_SELTO) != 0) { + ahc_print_path(ahc, scb); + printk("Saw Selection Timeout for SCB 0x%x\n", + scb_index); + } +#endif + ahc_scb_devinfo(ahc, &devinfo, scb); + ahc_set_transaction_status(scb, CAM_SEL_TIMEOUT); + ahc_freeze_devq(ahc, scb); + + /* + * Cancel any pending transactions on the device + * now that it seems to be missing. This will + * also revert us to async/narrow transfers until + * we can renegotiate with the device. + */ + ahc_handle_devreset(ahc, &devinfo, + CAM_SEL_TIMEOUT, + "Selection Timeout", + /*verbose_level*/1); + } + ahc_outb(ahc, CLRINT, CLRSCSIINT); + ahc_restart(ahc); + } else if ((status & BUSFREE) != 0 + && (ahc_inb(ahc, SIMODE1) & ENBUSFREE) != 0) { + struct ahc_devinfo devinfo; + u_int lastphase; + u_int saved_scsiid; + u_int saved_lun; + u_int target; + u_int initiator_role_id; + char channel; + int printerror; + + /* + * Clear our selection hardware as soon as possible. + * We may have an entry in the waiting Q for this target, + * that is affected by this busfree and we don't want to + * go about selecting the target while we handle the event. + */ + ahc_outb(ahc, SCSISEQ, + ahc_inb(ahc, SCSISEQ) & (ENSELI|ENRSELI|ENAUTOATNP)); + + /* + * Disable busfree interrupts and clear the busfree + * interrupt status. We do this here so that several + * bus transactions occur prior to clearing the SCSIINT + * latch. It can take a bit for the clearing to take effect. + */ + ahc_outb(ahc, SIMODE1, ahc_inb(ahc, SIMODE1) & ~ENBUSFREE); + ahc_outb(ahc, CLRSINT1, CLRBUSFREE|CLRSCSIPERR); + + /* + * Look at what phase we were last in. + * If its message out, chances are pretty good + * that the busfree was in response to one of + * our abort requests. + */ + lastphase = ahc_inb(ahc, LASTPHASE); + saved_scsiid = ahc_inb(ahc, SAVED_SCSIID); + saved_lun = ahc_inb(ahc, SAVED_LUN); + target = SCSIID_TARGET(ahc, saved_scsiid); + initiator_role_id = SCSIID_OUR_ID(saved_scsiid); + channel = SCSIID_CHANNEL(ahc, saved_scsiid); + ahc_compile_devinfo(&devinfo, initiator_role_id, + target, saved_lun, channel, ROLE_INITIATOR); + printerror = 1; + + if (lastphase == P_MESGOUT) { + u_int tag; + + tag = SCB_LIST_NULL; + if (ahc_sent_msg(ahc, AHCMSG_1B, MSG_ABORT_TAG, TRUE) + || ahc_sent_msg(ahc, AHCMSG_1B, MSG_ABORT, TRUE)) { + if (ahc->msgout_buf[ahc->msgout_index - 1] + == MSG_ABORT_TAG) + tag = scb->hscb->tag; + ahc_print_path(ahc, scb); + printk("SCB %d - Abort%s Completed.\n", + scb->hscb->tag, tag == SCB_LIST_NULL ? + "" : " Tag"); + ahc_abort_scbs(ahc, target, channel, + saved_lun, tag, + ROLE_INITIATOR, + CAM_REQ_ABORTED); + printerror = 0; + } else if (ahc_sent_msg(ahc, AHCMSG_1B, + MSG_BUS_DEV_RESET, TRUE)) { + ahc_compile_devinfo(&devinfo, + initiator_role_id, + target, + CAM_LUN_WILDCARD, + channel, + ROLE_INITIATOR); + ahc_handle_devreset(ahc, &devinfo, + CAM_BDR_SENT, + "Bus Device Reset", + /*verbose_level*/0); + printerror = 0; + } else if (ahc_sent_msg(ahc, AHCMSG_EXT, + MSG_EXT_PPR, FALSE)) { + struct ahc_initiator_tinfo *tinfo; + struct ahc_tmode_tstate *tstate; + + /* + * PPR Rejected. Try non-ppr negotiation + * and retry command. + */ + tinfo = ahc_fetch_transinfo(ahc, + devinfo.channel, + devinfo.our_scsiid, + devinfo.target, + &tstate); + tinfo->curr.transport_version = 2; + tinfo->goal.transport_version = 2; + tinfo->goal.ppr_options = 0; + ahc_qinfifo_requeue_tail(ahc, scb); + printerror = 0; + } else if (ahc_sent_msg(ahc, AHCMSG_EXT, + MSG_EXT_WDTR, FALSE)) { + /* + * Negotiation Rejected. Go-narrow and + * retry command. + */ + ahc_set_width(ahc, &devinfo, + MSG_EXT_WDTR_BUS_8_BIT, + AHC_TRANS_CUR|AHC_TRANS_GOAL, + /*paused*/TRUE); + ahc_qinfifo_requeue_tail(ahc, scb); + printerror = 0; + } else if (ahc_sent_msg(ahc, AHCMSG_EXT, + MSG_EXT_SDTR, FALSE)) { + /* + * Negotiation Rejected. Go-async and + * retry command. + */ + ahc_set_syncrate(ahc, &devinfo, + /*syncrate*/NULL, + /*period*/0, /*offset*/0, + /*ppr_options*/0, + AHC_TRANS_CUR|AHC_TRANS_GOAL, + /*paused*/TRUE); + ahc_qinfifo_requeue_tail(ahc, scb); + printerror = 0; + } + } + if (printerror != 0) { + u_int i; + + if (scb != NULL) { + u_int tag; + + if ((scb->hscb->control & TAG_ENB) != 0) + tag = scb->hscb->tag; + else + tag = SCB_LIST_NULL; + ahc_print_path(ahc, scb); + ahc_abort_scbs(ahc, target, channel, + SCB_GET_LUN(scb), tag, + ROLE_INITIATOR, + CAM_UNEXP_BUSFREE); + } else { + /* + * We had not fully identified this connection, + * so we cannot abort anything. + */ + printk("%s: ", ahc_name(ahc)); + } + for (i = 0; i < num_phases; i++) { + if (lastphase == ahc_phase_table[i].phase) + break; + } + if (lastphase != P_BUSFREE) { + /* + * Renegotiate with this device at the + * next opportunity just in case this busfree + * is due to a negotiation mismatch with the + * device. + */ + ahc_force_renegotiation(ahc, &devinfo); + } + printk("Unexpected busfree %s\n" + "SEQADDR == 0x%x\n", + ahc_phase_table[i].phasemsg, + ahc_inb(ahc, SEQADDR0) + | (ahc_inb(ahc, SEQADDR1) << 8)); + } + ahc_outb(ahc, CLRINT, CLRSCSIINT); + ahc_restart(ahc); + } else { + printk("%s: Missing case in ahc_handle_scsiint. status = %x\n", + ahc_name(ahc), status); + ahc_outb(ahc, CLRINT, CLRSCSIINT); + } +} + +/* + * Force renegotiation to occur the next time we initiate + * a command to the current device. + */ +static void +ahc_force_renegotiation(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) +{ + struct ahc_initiator_tinfo *targ_info; + struct ahc_tmode_tstate *tstate; + + targ_info = ahc_fetch_transinfo(ahc, + devinfo->channel, + devinfo->our_scsiid, + devinfo->target, + &tstate); + ahc_update_neg_request(ahc, devinfo, tstate, + targ_info, AHC_NEG_IF_NON_ASYNC); +} + +#define AHC_MAX_STEPS 2000 +static void +ahc_clear_critical_section(struct ahc_softc *ahc) +{ + int stepping; + int steps; + u_int simode0; + u_int simode1; + + if (ahc->num_critical_sections == 0) + return; + + stepping = FALSE; + steps = 0; + simode0 = 0; + simode1 = 0; + for (;;) { + struct cs *cs; + u_int seqaddr; + u_int i; + + seqaddr = ahc_inb(ahc, SEQADDR0) + | (ahc_inb(ahc, SEQADDR1) << 8); + + /* + * Seqaddr represents the next instruction to execute, + * so we are really executing the instruction just + * before it. + */ + if (seqaddr != 0) + seqaddr -= 1; + cs = ahc->critical_sections; + for (i = 0; i < ahc->num_critical_sections; i++, cs++) { + + if (cs->begin < seqaddr && cs->end >= seqaddr) + break; + } + + if (i == ahc->num_critical_sections) + break; + + if (steps > AHC_MAX_STEPS) { + printk("%s: Infinite loop in critical section\n", + ahc_name(ahc)); + ahc_dump_card_state(ahc); + panic("critical section loop"); + } + + steps++; + if (stepping == FALSE) { + + /* + * Disable all interrupt sources so that the + * sequencer will not be stuck by a pausing + * interrupt condition while we attempt to + * leave a critical section. + */ + simode0 = ahc_inb(ahc, SIMODE0); + ahc_outb(ahc, SIMODE0, 0); + simode1 = ahc_inb(ahc, SIMODE1); + if ((ahc->features & AHC_DT) != 0) + /* + * On DT class controllers, we + * use the enhanced busfree logic. + * Unfortunately we cannot re-enable + * busfree detection within the + * current connection, so we must + * leave it on while single stepping. + */ + ahc_outb(ahc, SIMODE1, simode1 & ENBUSFREE); + else + ahc_outb(ahc, SIMODE1, 0); + ahc_outb(ahc, CLRINT, CLRSCSIINT); + ahc_outb(ahc, SEQCTL, ahc->seqctl | STEP); + stepping = TRUE; + } + if ((ahc->features & AHC_DT) != 0) { + ahc_outb(ahc, CLRSINT1, CLRBUSFREE); + ahc_outb(ahc, CLRINT, CLRSCSIINT); + } + ahc_outb(ahc, HCNTRL, ahc->unpause); + while (!ahc_is_paused(ahc)) + ahc_delay(200); + } + if (stepping) { + ahc_outb(ahc, SIMODE0, simode0); + ahc_outb(ahc, SIMODE1, simode1); + ahc_outb(ahc, SEQCTL, ahc->seqctl); + } +} + +/* + * Clear any pending interrupt status. + */ +static void +ahc_clear_intstat(struct ahc_softc *ahc) +{ + /* Clear any interrupt conditions this may have caused */ + ahc_outb(ahc, CLRSINT1, CLRSELTIMEO|CLRATNO|CLRSCSIRSTI + |CLRBUSFREE|CLRSCSIPERR|CLRPHASECHG| + CLRREQINIT); + ahc_flush_device_writes(ahc); + ahc_outb(ahc, CLRSINT0, CLRSELDO|CLRSELDI|CLRSELINGO); + ahc_flush_device_writes(ahc); + ahc_outb(ahc, CLRINT, CLRSCSIINT); + ahc_flush_device_writes(ahc); +} + +/**************************** Debugging Routines ******************************/ +#ifdef AHC_DEBUG +uint32_t ahc_debug = AHC_DEBUG_OPTS; +#endif + +#if 0 /* unused */ +static void +ahc_print_scb(struct scb *scb) +{ + int i; + + struct hardware_scb *hscb = scb->hscb; + + printk("scb:%p control:0x%x scsiid:0x%x lun:%d cdb_len:%d\n", + (void *)scb, + hscb->control, + hscb->scsiid, + hscb->lun, + hscb->cdb_len); + printk("Shared Data: "); + for (i = 0; i < sizeof(hscb->shared_data.cdb); i++) + printk("%#02x", hscb->shared_data.cdb[i]); + printk(" dataptr:%#x datacnt:%#x sgptr:%#x tag:%#x\n", + ahc_le32toh(hscb->dataptr), + ahc_le32toh(hscb->datacnt), + ahc_le32toh(hscb->sgptr), + hscb->tag); + if (scb->sg_count > 0) { + for (i = 0; i < scb->sg_count; i++) { + printk("sg[%d] - Addr 0x%x%x : Length %d\n", + i, + (ahc_le32toh(scb->sg_list[i].len) >> 24 + & SG_HIGH_ADDR_BITS), + ahc_le32toh(scb->sg_list[i].addr), + ahc_le32toh(scb->sg_list[i].len)); + } + } +} +#endif + +/************************* Transfer Negotiation *******************************/ +/* + * Allocate per target mode instance (ID we respond to as a target) + * transfer negotiation data structures. + */ +static struct ahc_tmode_tstate * +ahc_alloc_tstate(struct ahc_softc *ahc, u_int scsi_id, char channel) +{ + struct ahc_tmode_tstate *master_tstate; + struct ahc_tmode_tstate *tstate; + int i; + + master_tstate = ahc->enabled_targets[ahc->our_id]; + if (channel == 'B') { + scsi_id += 8; + master_tstate = ahc->enabled_targets[ahc->our_id_b + 8]; + } + if (ahc->enabled_targets[scsi_id] != NULL + && ahc->enabled_targets[scsi_id] != master_tstate) + panic("%s: ahc_alloc_tstate - Target already allocated", + ahc_name(ahc)); + tstate = kmalloc(sizeof(*tstate), GFP_ATOMIC); + if (tstate == NULL) + return (NULL); + + /* + * If we have allocated a master tstate, copy user settings from + * the master tstate (taken from SRAM or the EEPROM) for this + * channel, but reset our current and goal settings to async/narrow + * until an initiator talks to us. + */ + if (master_tstate != NULL) { + memcpy(tstate, master_tstate, sizeof(*tstate)); + memset(tstate->enabled_luns, 0, sizeof(tstate->enabled_luns)); + tstate->ultraenb = 0; + for (i = 0; i < AHC_NUM_TARGETS; i++) { + memset(&tstate->transinfo[i].curr, 0, + sizeof(tstate->transinfo[i].curr)); + memset(&tstate->transinfo[i].goal, 0, + sizeof(tstate->transinfo[i].goal)); + } + } else + memset(tstate, 0, sizeof(*tstate)); + ahc->enabled_targets[scsi_id] = tstate; + return (tstate); +} + +#ifdef AHC_TARGET_MODE +/* + * Free per target mode instance (ID we respond to as a target) + * transfer negotiation data structures. + */ +static void +ahc_free_tstate(struct ahc_softc *ahc, u_int scsi_id, char channel, int force) +{ + struct ahc_tmode_tstate *tstate; + + /* + * Don't clean up our "master" tstate. + * It has our default user settings. + */ + if (((channel == 'B' && scsi_id == ahc->our_id_b) + || (channel == 'A' && scsi_id == ahc->our_id)) + && force == FALSE) + return; + + if (channel == 'B') + scsi_id += 8; + tstate = ahc->enabled_targets[scsi_id]; + kfree(tstate); + ahc->enabled_targets[scsi_id] = NULL; +} +#endif + +/* + * Called when we have an active connection to a target on the bus, + * this function finds the nearest syncrate to the input period limited + * by the capabilities of the bus connectivity of and sync settings for + * the target. + */ +static const struct ahc_syncrate * +ahc_devlimited_syncrate(struct ahc_softc *ahc, + struct ahc_initiator_tinfo *tinfo, + u_int *period, u_int *ppr_options, role_t role) +{ + struct ahc_transinfo *transinfo; + u_int maxsync; + + if ((ahc->features & AHC_ULTRA2) != 0) { + if ((ahc_inb(ahc, SBLKCTL) & ENAB40) != 0 + && (ahc_inb(ahc, SSTAT2) & EXP_ACTIVE) == 0) { + maxsync = AHC_SYNCRATE_DT; + } else { + maxsync = AHC_SYNCRATE_ULTRA; + /* Can't do DT on an SE bus */ + *ppr_options &= ~MSG_EXT_PPR_DT_REQ; + } + } else if ((ahc->features & AHC_ULTRA) != 0) { + maxsync = AHC_SYNCRATE_ULTRA; + } else { + maxsync = AHC_SYNCRATE_FAST; + } + /* + * Never allow a value higher than our current goal + * period otherwise we may allow a target initiated + * negotiation to go above the limit as set by the + * user. In the case of an initiator initiated + * sync negotiation, we limit based on the user + * setting. This allows the system to still accept + * incoming negotiations even if target initiated + * negotiation is not performed. + */ + if (role == ROLE_TARGET) + transinfo = &tinfo->user; + else + transinfo = &tinfo->goal; + *ppr_options &= transinfo->ppr_options; + if (transinfo->width == MSG_EXT_WDTR_BUS_8_BIT) { + maxsync = max(maxsync, (u_int)AHC_SYNCRATE_ULTRA2); + *ppr_options &= ~MSG_EXT_PPR_DT_REQ; + } + if (transinfo->period == 0) { + *period = 0; + *ppr_options = 0; + return (NULL); + } + *period = max(*period, (u_int)transinfo->period); + return (ahc_find_syncrate(ahc, period, ppr_options, maxsync)); +} + +/* + * Look up the valid period to SCSIRATE conversion in our table. + * Return the period and offset that should be sent to the target + * if this was the beginning of an SDTR. + */ +const struct ahc_syncrate * +ahc_find_syncrate(struct ahc_softc *ahc, u_int *period, + u_int *ppr_options, u_int maxsync) +{ + const struct ahc_syncrate *syncrate; + + if ((ahc->features & AHC_DT) == 0) + *ppr_options &= ~MSG_EXT_PPR_DT_REQ; + + /* Skip all DT only entries if DT is not available */ + if ((*ppr_options & MSG_EXT_PPR_DT_REQ) == 0 + && maxsync < AHC_SYNCRATE_ULTRA2) + maxsync = AHC_SYNCRATE_ULTRA2; + + /* Now set the maxsync based on the card capabilities + * DT is already done above */ + if ((ahc->features & (AHC_DT | AHC_ULTRA2)) == 0 + && maxsync < AHC_SYNCRATE_ULTRA) + maxsync = AHC_SYNCRATE_ULTRA; + if ((ahc->features & (AHC_DT | AHC_ULTRA2 | AHC_ULTRA)) == 0 + && maxsync < AHC_SYNCRATE_FAST) + maxsync = AHC_SYNCRATE_FAST; + + for (syncrate = &ahc_syncrates[maxsync]; + syncrate->rate != NULL; + syncrate++) { + + /* + * The Ultra2 table doesn't go as low + * as for the Fast/Ultra cards. + */ + if ((ahc->features & AHC_ULTRA2) != 0 + && (syncrate->sxfr_u2 == 0)) + break; + + if (*period <= syncrate->period) { + /* + * When responding to a target that requests + * sync, the requested rate may fall between + * two rates that we can output, but still be + * a rate that we can receive. Because of this, + * we want to respond to the target with + * the same rate that it sent to us even + * if the period we use to send data to it + * is lower. Only lower the response period + * if we must. + */ + if (syncrate == &ahc_syncrates[maxsync]) + *period = syncrate->period; + + /* + * At some speeds, we only support + * ST transfers. + */ + if ((syncrate->sxfr_u2 & ST_SXFR) != 0) + *ppr_options &= ~MSG_EXT_PPR_DT_REQ; + break; + } + } + + if ((*period == 0) + || (syncrate->rate == NULL) + || ((ahc->features & AHC_ULTRA2) != 0 + && (syncrate->sxfr_u2 == 0))) { + /* Use asynchronous transfers. */ + *period = 0; + syncrate = NULL; + *ppr_options &= ~MSG_EXT_PPR_DT_REQ; + } + return (syncrate); +} + +/* + * Convert from an entry in our syncrate table to the SCSI equivalent + * sync "period" factor. + */ +u_int +ahc_find_period(struct ahc_softc *ahc, u_int scsirate, u_int maxsync) +{ + const struct ahc_syncrate *syncrate; + + if ((ahc->features & AHC_ULTRA2) != 0) + scsirate &= SXFR_ULTRA2; + else + scsirate &= SXFR; + + /* now set maxsync based on card capabilities */ + if ((ahc->features & AHC_DT) == 0 && maxsync < AHC_SYNCRATE_ULTRA2) + maxsync = AHC_SYNCRATE_ULTRA2; + if ((ahc->features & (AHC_DT | AHC_ULTRA2)) == 0 + && maxsync < AHC_SYNCRATE_ULTRA) + maxsync = AHC_SYNCRATE_ULTRA; + if ((ahc->features & (AHC_DT | AHC_ULTRA2 | AHC_ULTRA)) == 0 + && maxsync < AHC_SYNCRATE_FAST) + maxsync = AHC_SYNCRATE_FAST; + + + syncrate = &ahc_syncrates[maxsync]; + while (syncrate->rate != NULL) { + + if ((ahc->features & AHC_ULTRA2) != 0) { + if (syncrate->sxfr_u2 == 0) + break; + else if (scsirate == (syncrate->sxfr_u2 & SXFR_ULTRA2)) + return (syncrate->period); + } else if (scsirate == (syncrate->sxfr & SXFR)) { + return (syncrate->period); + } + syncrate++; + } + return (0); /* async */ +} + +/* + * Truncate the given synchronous offset to a value the + * current adapter type and syncrate are capable of. + */ +static void +ahc_validate_offset(struct ahc_softc *ahc, + struct ahc_initiator_tinfo *tinfo, + const struct ahc_syncrate *syncrate, + u_int *offset, int wide, role_t role) +{ + u_int maxoffset; + + /* Limit offset to what we can do */ + if (syncrate == NULL) { + maxoffset = 0; + } else if ((ahc->features & AHC_ULTRA2) != 0) { + maxoffset = MAX_OFFSET_ULTRA2; + } else { + if (wide) + maxoffset = MAX_OFFSET_16BIT; + else + maxoffset = MAX_OFFSET_8BIT; + } + *offset = min(*offset, maxoffset); + if (tinfo != NULL) { + if (role == ROLE_TARGET) + *offset = min(*offset, (u_int)tinfo->user.offset); + else + *offset = min(*offset, (u_int)tinfo->goal.offset); + } +} + +/* + * Truncate the given transfer width parameter to a value the + * current adapter type is capable of. + */ +static void +ahc_validate_width(struct ahc_softc *ahc, struct ahc_initiator_tinfo *tinfo, + u_int *bus_width, role_t role) +{ + switch (*bus_width) { + default: + if (ahc->features & AHC_WIDE) { + /* Respond Wide */ + *bus_width = MSG_EXT_WDTR_BUS_16_BIT; + break; + } + fallthrough; + case MSG_EXT_WDTR_BUS_8_BIT: + *bus_width = MSG_EXT_WDTR_BUS_8_BIT; + break; + } + if (tinfo != NULL) { + if (role == ROLE_TARGET) + *bus_width = min((u_int)tinfo->user.width, *bus_width); + else + *bus_width = min((u_int)tinfo->goal.width, *bus_width); + } +} + +/* + * Update the bitmask of targets for which the controller should + * negotiate with at the next convenient opportunity. This currently + * means the next time we send the initial identify messages for + * a new transaction. + */ +int +ahc_update_neg_request(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, + struct ahc_tmode_tstate *tstate, + struct ahc_initiator_tinfo *tinfo, ahc_neg_type neg_type) +{ + u_int auto_negotiate_orig; + + auto_negotiate_orig = tstate->auto_negotiate; + if (neg_type == AHC_NEG_ALWAYS) { + /* + * Force our "current" settings to be + * unknown so that unless a bus reset + * occurs the need to renegotiate is + * recorded persistently. + */ + if ((ahc->features & AHC_WIDE) != 0) + tinfo->curr.width = AHC_WIDTH_UNKNOWN; + tinfo->curr.period = AHC_PERIOD_UNKNOWN; + tinfo->curr.offset = AHC_OFFSET_UNKNOWN; + } + if (tinfo->curr.period != tinfo->goal.period + || tinfo->curr.width != tinfo->goal.width + || tinfo->curr.offset != tinfo->goal.offset + || tinfo->curr.ppr_options != tinfo->goal.ppr_options + || (neg_type == AHC_NEG_IF_NON_ASYNC + && (tinfo->goal.offset != 0 + || tinfo->goal.width != MSG_EXT_WDTR_BUS_8_BIT + || tinfo->goal.ppr_options != 0))) + tstate->auto_negotiate |= devinfo->target_mask; + else + tstate->auto_negotiate &= ~devinfo->target_mask; + + return (auto_negotiate_orig != tstate->auto_negotiate); +} + +/* + * Update the user/goal/curr tables of synchronous negotiation + * parameters as well as, in the case of a current or active update, + * any data structures on the host controller. In the case of an + * active update, the specified target is currently talking to us on + * the bus, so the transfer parameter update must take effect + * immediately. + */ +void +ahc_set_syncrate(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, + const struct ahc_syncrate *syncrate, u_int period, + u_int offset, u_int ppr_options, u_int type, int paused) +{ + struct ahc_initiator_tinfo *tinfo; + struct ahc_tmode_tstate *tstate; + u_int old_period; + u_int old_offset; + u_int old_ppr; + int active; + int update_needed; + + active = (type & AHC_TRANS_ACTIVE) == AHC_TRANS_ACTIVE; + update_needed = 0; + + if (syncrate == NULL) { + period = 0; + offset = 0; + } + + tinfo = ahc_fetch_transinfo(ahc, devinfo->channel, devinfo->our_scsiid, + devinfo->target, &tstate); + + if ((type & AHC_TRANS_USER) != 0) { + tinfo->user.period = period; + tinfo->user.offset = offset; + tinfo->user.ppr_options = ppr_options; + } + + if ((type & AHC_TRANS_GOAL) != 0) { + tinfo->goal.period = period; + tinfo->goal.offset = offset; + tinfo->goal.ppr_options = ppr_options; + } + + old_period = tinfo->curr.period; + old_offset = tinfo->curr.offset; + old_ppr = tinfo->curr.ppr_options; + + if ((type & AHC_TRANS_CUR) != 0 + && (old_period != period + || old_offset != offset + || old_ppr != ppr_options)) { + u_int scsirate; + + update_needed++; + scsirate = tinfo->scsirate; + if ((ahc->features & AHC_ULTRA2) != 0) { + + scsirate &= ~(SXFR_ULTRA2|SINGLE_EDGE|ENABLE_CRC); + if (syncrate != NULL) { + scsirate |= syncrate->sxfr_u2; + if ((ppr_options & MSG_EXT_PPR_DT_REQ) != 0) + scsirate |= ENABLE_CRC; + else + scsirate |= SINGLE_EDGE; + } + } else { + + scsirate &= ~(SXFR|SOFS); + /* + * Ensure Ultra mode is set properly for + * this target. + */ + tstate->ultraenb &= ~devinfo->target_mask; + if (syncrate != NULL) { + if (syncrate->sxfr & ULTRA_SXFR) { + tstate->ultraenb |= + devinfo->target_mask; + } + scsirate |= syncrate->sxfr & SXFR; + scsirate |= offset & SOFS; + } + if (active) { + u_int sxfrctl0; + + sxfrctl0 = ahc_inb(ahc, SXFRCTL0); + sxfrctl0 &= ~FAST20; + if (tstate->ultraenb & devinfo->target_mask) + sxfrctl0 |= FAST20; + ahc_outb(ahc, SXFRCTL0, sxfrctl0); + } + } + if (active) { + ahc_outb(ahc, SCSIRATE, scsirate); + if ((ahc->features & AHC_ULTRA2) != 0) + ahc_outb(ahc, SCSIOFFSET, offset); + } + + tinfo->scsirate = scsirate; + tinfo->curr.period = period; + tinfo->curr.offset = offset; + tinfo->curr.ppr_options = ppr_options; + + ahc_send_async(ahc, devinfo->channel, devinfo->target, + CAM_LUN_WILDCARD, AC_TRANSFER_NEG); + if (bootverbose) { + if (offset != 0) { + printk("%s: target %d synchronous at %sMHz%s, " + "offset = 0x%x\n", ahc_name(ahc), + devinfo->target, syncrate->rate, + (ppr_options & MSG_EXT_PPR_DT_REQ) + ? " DT" : "", offset); + } else { + printk("%s: target %d using " + "asynchronous transfers\n", + ahc_name(ahc), devinfo->target); + } + } + } + + update_needed += ahc_update_neg_request(ahc, devinfo, tstate, + tinfo, AHC_NEG_TO_GOAL); + + if (update_needed) + ahc_update_pending_scbs(ahc); +} + +/* + * Update the user/goal/curr tables of wide negotiation + * parameters as well as, in the case of a current or active update, + * any data structures on the host controller. In the case of an + * active update, the specified target is currently talking to us on + * the bus, so the transfer parameter update must take effect + * immediately. + */ +void +ahc_set_width(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, + u_int width, u_int type, int paused) +{ + struct ahc_initiator_tinfo *tinfo; + struct ahc_tmode_tstate *tstate; + u_int oldwidth; + int active; + int update_needed; + + active = (type & AHC_TRANS_ACTIVE) == AHC_TRANS_ACTIVE; + update_needed = 0; + tinfo = ahc_fetch_transinfo(ahc, devinfo->channel, devinfo->our_scsiid, + devinfo->target, &tstate); + + if ((type & AHC_TRANS_USER) != 0) + tinfo->user.width = width; + + if ((type & AHC_TRANS_GOAL) != 0) + tinfo->goal.width = width; + + oldwidth = tinfo->curr.width; + if ((type & AHC_TRANS_CUR) != 0 && oldwidth != width) { + u_int scsirate; + + update_needed++; + scsirate = tinfo->scsirate; + scsirate &= ~WIDEXFER; + if (width == MSG_EXT_WDTR_BUS_16_BIT) + scsirate |= WIDEXFER; + + tinfo->scsirate = scsirate; + + if (active) + ahc_outb(ahc, SCSIRATE, scsirate); + + tinfo->curr.width = width; + + ahc_send_async(ahc, devinfo->channel, devinfo->target, + CAM_LUN_WILDCARD, AC_TRANSFER_NEG); + if (bootverbose) { + printk("%s: target %d using %dbit transfers\n", + ahc_name(ahc), devinfo->target, + 8 * (0x01 << width)); + } + } + + update_needed += ahc_update_neg_request(ahc, devinfo, tstate, + tinfo, AHC_NEG_TO_GOAL); + if (update_needed) + ahc_update_pending_scbs(ahc); +} + +/* + * Update the current state of tagged queuing for a given target. + */ +static void +ahc_set_tags(struct ahc_softc *ahc, struct scsi_cmnd *cmd, + struct ahc_devinfo *devinfo, ahc_queue_alg alg) +{ + struct scsi_device *sdev = cmd->device; + + ahc_platform_set_tags(ahc, sdev, devinfo, alg); + ahc_send_async(ahc, devinfo->channel, devinfo->target, + devinfo->lun, AC_TRANSFER_NEG); +} + +/* + * When the transfer settings for a connection change, update any + * in-transit SCBs to contain the new data so the hardware will + * be set correctly during future (re)selections. + */ +static void +ahc_update_pending_scbs(struct ahc_softc *ahc) +{ + struct scb *pending_scb; + int pending_scb_count; + int i; + int paused; + u_int saved_scbptr; + + /* + * Traverse the pending SCB list and ensure that all of the + * SCBs there have the proper settings. + */ + pending_scb_count = 0; + LIST_FOREACH(pending_scb, &ahc->pending_scbs, pending_links) { + struct ahc_devinfo devinfo; + struct hardware_scb *pending_hscb; + struct ahc_initiator_tinfo *tinfo; + struct ahc_tmode_tstate *tstate; + + ahc_scb_devinfo(ahc, &devinfo, pending_scb); + tinfo = ahc_fetch_transinfo(ahc, devinfo.channel, + devinfo.our_scsiid, + devinfo.target, &tstate); + pending_hscb = pending_scb->hscb; + pending_hscb->control &= ~ULTRAENB; + if ((tstate->ultraenb & devinfo.target_mask) != 0) + pending_hscb->control |= ULTRAENB; + pending_hscb->scsirate = tinfo->scsirate; + pending_hscb->scsioffset = tinfo->curr.offset; + if ((tstate->auto_negotiate & devinfo.target_mask) == 0 + && (pending_scb->flags & SCB_AUTO_NEGOTIATE) != 0) { + pending_scb->flags &= ~SCB_AUTO_NEGOTIATE; + pending_hscb->control &= ~MK_MESSAGE; + } + ahc_sync_scb(ahc, pending_scb, + BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); + pending_scb_count++; + } + + if (pending_scb_count == 0) + return; + + if (ahc_is_paused(ahc)) { + paused = 1; + } else { + paused = 0; + ahc_pause(ahc); + } + + saved_scbptr = ahc_inb(ahc, SCBPTR); + /* Ensure that the hscbs down on the card match the new information */ + for (i = 0; i < ahc->scb_data->maxhscbs; i++) { + struct hardware_scb *pending_hscb; + u_int control; + u_int scb_tag; + + ahc_outb(ahc, SCBPTR, i); + scb_tag = ahc_inb(ahc, SCB_TAG); + pending_scb = ahc_lookup_scb(ahc, scb_tag); + if (pending_scb == NULL) + continue; + + pending_hscb = pending_scb->hscb; + control = ahc_inb(ahc, SCB_CONTROL); + control &= ~(ULTRAENB|MK_MESSAGE); + control |= pending_hscb->control & (ULTRAENB|MK_MESSAGE); + ahc_outb(ahc, SCB_CONTROL, control); + ahc_outb(ahc, SCB_SCSIRATE, pending_hscb->scsirate); + ahc_outb(ahc, SCB_SCSIOFFSET, pending_hscb->scsioffset); + } + ahc_outb(ahc, SCBPTR, saved_scbptr); + + if (paused == 0) + ahc_unpause(ahc); +} + +/**************************** Pathing Information *****************************/ +static void +ahc_fetch_devinfo(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) +{ + u_int saved_scsiid; + role_t role; + int our_id; + + if (ahc_inb(ahc, SSTAT0) & TARGET) + role = ROLE_TARGET; + else + role = ROLE_INITIATOR; + + if (role == ROLE_TARGET + && (ahc->features & AHC_MULTI_TID) != 0 + && (ahc_inb(ahc, SEQ_FLAGS) + & (CMDPHASE_PENDING|TARG_CMD_PENDING|NO_DISCONNECT)) != 0) { + /* We were selected, so pull our id from TARGIDIN */ + our_id = ahc_inb(ahc, TARGIDIN) & OID; + } else if ((ahc->features & AHC_ULTRA2) != 0) + our_id = ahc_inb(ahc, SCSIID_ULTRA2) & OID; + else + our_id = ahc_inb(ahc, SCSIID) & OID; + + saved_scsiid = ahc_inb(ahc, SAVED_SCSIID); + ahc_compile_devinfo(devinfo, + our_id, + SCSIID_TARGET(ahc, saved_scsiid), + ahc_inb(ahc, SAVED_LUN), + SCSIID_CHANNEL(ahc, saved_scsiid), + role); +} + +static const struct ahc_phase_table_entry* +ahc_lookup_phase_entry(int phase) +{ + const struct ahc_phase_table_entry *entry; + const struct ahc_phase_table_entry *last_entry; + + /* + * num_phases doesn't include the default entry which + * will be returned if the phase doesn't match. + */ + last_entry = &ahc_phase_table[num_phases]; + for (entry = ahc_phase_table; entry < last_entry; entry++) { + if (phase == entry->phase) + break; + } + return (entry); +} + +void +ahc_compile_devinfo(struct ahc_devinfo *devinfo, u_int our_id, u_int target, + u_int lun, char channel, role_t role) +{ + devinfo->our_scsiid = our_id; + devinfo->target = target; + devinfo->lun = lun; + devinfo->target_offset = target; + devinfo->channel = channel; + devinfo->role = role; + if (channel == 'B') + devinfo->target_offset += 8; + devinfo->target_mask = (0x01 << devinfo->target_offset); +} + +void +ahc_print_devinfo(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) +{ + printk("%s:%c:%d:%d: ", ahc_name(ahc), devinfo->channel, + devinfo->target, devinfo->lun); +} + +static void +ahc_scb_devinfo(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, + struct scb *scb) +{ + role_t role; + int our_id; + + our_id = SCSIID_OUR_ID(scb->hscb->scsiid); + role = ROLE_INITIATOR; + if ((scb->flags & SCB_TARGET_SCB) != 0) + role = ROLE_TARGET; + ahc_compile_devinfo(devinfo, our_id, SCB_GET_TARGET(ahc, scb), + SCB_GET_LUN(scb), SCB_GET_CHANNEL(ahc, scb), role); +} + + +/************************ Message Phase Processing ****************************/ +static void +ahc_assert_atn(struct ahc_softc *ahc) +{ + u_int scsisigo; + + scsisigo = ATNO; + if ((ahc->features & AHC_DT) == 0) + scsisigo |= ahc_inb(ahc, SCSISIGI); + ahc_outb(ahc, SCSISIGO, scsisigo); +} + +/* + * When an initiator transaction with the MK_MESSAGE flag either reconnects + * or enters the initial message out phase, we are interrupted. Fill our + * outgoing message buffer with the appropriate message and beging handing + * the message phase(s) manually. + */ +static void +ahc_setup_initiator_msgout(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, + struct scb *scb) +{ + /* + * To facilitate adding multiple messages together, + * each routine should increment the index and len + * variables instead of setting them explicitly. + */ + ahc->msgout_index = 0; + ahc->msgout_len = 0; + + if ((scb->flags & SCB_DEVICE_RESET) == 0 + && ahc_inb(ahc, MSG_OUT) == MSG_IDENTIFYFLAG) { + u_int identify_msg; + + identify_msg = MSG_IDENTIFYFLAG | SCB_GET_LUN(scb); + if ((scb->hscb->control & DISCENB) != 0) + identify_msg |= MSG_IDENTIFY_DISCFLAG; + ahc->msgout_buf[ahc->msgout_index++] = identify_msg; + ahc->msgout_len++; + + if ((scb->hscb->control & TAG_ENB) != 0) { + ahc->msgout_buf[ahc->msgout_index++] = + scb->hscb->control & (TAG_ENB|SCB_TAG_TYPE); + ahc->msgout_buf[ahc->msgout_index++] = scb->hscb->tag; + ahc->msgout_len += 2; + } + } + + if (scb->flags & SCB_DEVICE_RESET) { + ahc->msgout_buf[ahc->msgout_index++] = MSG_BUS_DEV_RESET; + ahc->msgout_len++; + ahc_print_path(ahc, scb); + printk("Bus Device Reset Message Sent\n"); + /* + * Clear our selection hardware in advance of + * the busfree. We may have an entry in the waiting + * Q for this target, and we don't want to go about + * selecting while we handle the busfree and blow it + * away. + */ + ahc_outb(ahc, SCSISEQ, (ahc_inb(ahc, SCSISEQ) & ~ENSELO)); + } else if ((scb->flags & SCB_ABORT) != 0) { + if ((scb->hscb->control & TAG_ENB) != 0) + ahc->msgout_buf[ahc->msgout_index++] = MSG_ABORT_TAG; + else + ahc->msgout_buf[ahc->msgout_index++] = MSG_ABORT; + ahc->msgout_len++; + ahc_print_path(ahc, scb); + printk("Abort%s Message Sent\n", + (scb->hscb->control & TAG_ENB) != 0 ? " Tag" : ""); + /* + * Clear our selection hardware in advance of + * the busfree. We may have an entry in the waiting + * Q for this target, and we don't want to go about + * selecting while we handle the busfree and blow it + * away. + */ + ahc_outb(ahc, SCSISEQ, (ahc_inb(ahc, SCSISEQ) & ~ENSELO)); + } else if ((scb->flags & (SCB_AUTO_NEGOTIATE|SCB_NEGOTIATE)) != 0) { + ahc_build_transfer_msg(ahc, devinfo); + } else { + printk("ahc_intr: AWAITING_MSG for an SCB that " + "does not have a waiting message\n"); + printk("SCSIID = %x, target_mask = %x\n", scb->hscb->scsiid, + devinfo->target_mask); + panic("SCB = %d, SCB Control = %x, MSG_OUT = %x " + "SCB flags = %x", scb->hscb->tag, scb->hscb->control, + ahc_inb(ahc, MSG_OUT), scb->flags); + } + + /* + * Clear the MK_MESSAGE flag from the SCB so we aren't + * asked to send this message again. + */ + ahc_outb(ahc, SCB_CONTROL, ahc_inb(ahc, SCB_CONTROL) & ~MK_MESSAGE); + scb->hscb->control &= ~MK_MESSAGE; + ahc->msgout_index = 0; + ahc->msg_type = MSG_TYPE_INITIATOR_MSGOUT; +} + +/* + * Build an appropriate transfer negotiation message for the + * currently active target. + */ +static void +ahc_build_transfer_msg(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) +{ + /* + * We need to initiate transfer negotiations. + * If our current and goal settings are identical, + * we want to renegotiate due to a check condition. + */ + struct ahc_initiator_tinfo *tinfo; + struct ahc_tmode_tstate *tstate; + const struct ahc_syncrate *rate; + int dowide; + int dosync; + int doppr; + u_int period; + u_int ppr_options; + u_int offset; + + tinfo = ahc_fetch_transinfo(ahc, devinfo->channel, devinfo->our_scsiid, + devinfo->target, &tstate); + /* + * Filter our period based on the current connection. + * If we can't perform DT transfers on this segment (not in LVD + * mode for instance), then our decision to issue a PPR message + * may change. + */ + period = tinfo->goal.period; + offset = tinfo->goal.offset; + ppr_options = tinfo->goal.ppr_options; + /* Target initiated PPR is not allowed in the SCSI spec */ + if (devinfo->role == ROLE_TARGET) + ppr_options = 0; + rate = ahc_devlimited_syncrate(ahc, tinfo, &period, + &ppr_options, devinfo->role); + dowide = tinfo->curr.width != tinfo->goal.width; + dosync = tinfo->curr.offset != offset || tinfo->curr.period != period; + /* + * Only use PPR if we have options that need it, even if the device + * claims to support it. There might be an expander in the way + * that doesn't. + */ + doppr = ppr_options != 0; + + if (!dowide && !dosync && !doppr) { + dowide = tinfo->goal.width != MSG_EXT_WDTR_BUS_8_BIT; + dosync = tinfo->goal.offset != 0; + } + + if (!dowide && !dosync && !doppr) { + /* + * Force async with a WDTR message if we have a wide bus, + * or just issue an SDTR with a 0 offset. + */ + if ((ahc->features & AHC_WIDE) != 0) + dowide = 1; + else + dosync = 1; + + if (bootverbose) { + ahc_print_devinfo(ahc, devinfo); + printk("Ensuring async\n"); + } + } + + /* Target initiated PPR is not allowed in the SCSI spec */ + if (devinfo->role == ROLE_TARGET) + doppr = 0; + + /* + * Both the PPR message and SDTR message require the + * goal syncrate to be limited to what the target device + * is capable of handling (based on whether an LVD->SE + * expander is on the bus), so combine these two cases. + * Regardless, guarantee that if we are using WDTR and SDTR + * messages that WDTR comes first. + */ + if (doppr || (dosync && !dowide)) { + + offset = tinfo->goal.offset; + ahc_validate_offset(ahc, tinfo, rate, &offset, + doppr ? tinfo->goal.width + : tinfo->curr.width, + devinfo->role); + if (doppr) { + ahc_construct_ppr(ahc, devinfo, period, offset, + tinfo->goal.width, ppr_options); + } else { + ahc_construct_sdtr(ahc, devinfo, period, offset); + } + } else { + ahc_construct_wdtr(ahc, devinfo, tinfo->goal.width); + } +} + +/* + * Build a synchronous negotiation message in our message + * buffer based on the input parameters. + */ +static void +ahc_construct_sdtr(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, + u_int period, u_int offset) +{ + if (offset == 0) + period = AHC_ASYNC_XFER_PERIOD; + ahc->msgout_index += spi_populate_sync_msg( + ahc->msgout_buf + ahc->msgout_index, period, offset); + ahc->msgout_len += 5; + if (bootverbose) { + printk("(%s:%c:%d:%d): Sending SDTR period %x, offset %x\n", + ahc_name(ahc), devinfo->channel, devinfo->target, + devinfo->lun, period, offset); + } +} + +/* + * Build a wide negotiation message in our message + * buffer based on the input parameters. + */ +static void +ahc_construct_wdtr(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, + u_int bus_width) +{ + ahc->msgout_index += spi_populate_width_msg( + ahc->msgout_buf + ahc->msgout_index, bus_width); + ahc->msgout_len += 4; + if (bootverbose) { + printk("(%s:%c:%d:%d): Sending WDTR %x\n", + ahc_name(ahc), devinfo->channel, devinfo->target, + devinfo->lun, bus_width); + } +} + +/* + * Build a parallel protocol request message in our message + * buffer based on the input parameters. + */ +static void +ahc_construct_ppr(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, + u_int period, u_int offset, u_int bus_width, + u_int ppr_options) +{ + if (offset == 0) + period = AHC_ASYNC_XFER_PERIOD; + ahc->msgout_index += spi_populate_ppr_msg( + ahc->msgout_buf + ahc->msgout_index, period, offset, + bus_width, ppr_options); + ahc->msgout_len += 8; + if (bootverbose) { + printk("(%s:%c:%d:%d): Sending PPR bus_width %x, period %x, " + "offset %x, ppr_options %x\n", ahc_name(ahc), + devinfo->channel, devinfo->target, devinfo->lun, + bus_width, period, offset, ppr_options); + } +} + +/* + * Clear any active message state. + */ +static void +ahc_clear_msg_state(struct ahc_softc *ahc) +{ + ahc->msgout_len = 0; + ahc->msgin_index = 0; + ahc->msg_type = MSG_TYPE_NONE; + if ((ahc_inb(ahc, SCSISIGI) & ATNI) != 0) { + /* + * The target didn't care to respond to our + * message request, so clear ATN. + */ + ahc_outb(ahc, CLRSINT1, CLRATNO); + } + ahc_outb(ahc, MSG_OUT, MSG_NOOP); + ahc_outb(ahc, SEQ_FLAGS2, + ahc_inb(ahc, SEQ_FLAGS2) & ~TARGET_MSG_PENDING); +} + +static void +ahc_handle_proto_violation(struct ahc_softc *ahc) +{ + struct ahc_devinfo devinfo; + struct scb *scb; + u_int scbid; + u_int seq_flags; + u_int curphase; + u_int lastphase; + int found; + + ahc_fetch_devinfo(ahc, &devinfo); + scbid = ahc_inb(ahc, SCB_TAG); + scb = ahc_lookup_scb(ahc, scbid); + seq_flags = ahc_inb(ahc, SEQ_FLAGS); + curphase = ahc_inb(ahc, SCSISIGI) & PHASE_MASK; + lastphase = ahc_inb(ahc, LASTPHASE); + if ((seq_flags & NOT_IDENTIFIED) != 0) { + + /* + * The reconnecting target either did not send an + * identify message, or did, but we didn't find an SCB + * to match. + */ + ahc_print_devinfo(ahc, &devinfo); + printk("Target did not send an IDENTIFY message. " + "LASTPHASE = 0x%x.\n", lastphase); + scb = NULL; + } else if (scb == NULL) { + /* + * We don't seem to have an SCB active for this + * transaction. Print an error and reset the bus. + */ + ahc_print_devinfo(ahc, &devinfo); + printk("No SCB found during protocol violation\n"); + goto proto_violation_reset; + } else { + ahc_set_transaction_status(scb, CAM_SEQUENCE_FAIL); + if ((seq_flags & NO_CDB_SENT) != 0) { + ahc_print_path(ahc, scb); + printk("No or incomplete CDB sent to device.\n"); + } else if ((ahc_inb(ahc, SCB_CONTROL) & STATUS_RCVD) == 0) { + /* + * The target never bothered to provide status to + * us prior to completing the command. Since we don't + * know the disposition of this command, we must attempt + * to abort it. Assert ATN and prepare to send an abort + * message. + */ + ahc_print_path(ahc, scb); + printk("Completed command without status.\n"); + } else { + ahc_print_path(ahc, scb); + printk("Unknown protocol violation.\n"); + ahc_dump_card_state(ahc); + } + } + if ((lastphase & ~P_DATAIN_DT) == 0 + || lastphase == P_COMMAND) { +proto_violation_reset: + /* + * Target either went directly to data/command + * phase or didn't respond to our ATN. + * The only safe thing to do is to blow + * it away with a bus reset. + */ + found = ahc_reset_channel(ahc, 'A', TRUE); + printk("%s: Issued Channel %c Bus Reset. " + "%d SCBs aborted\n", ahc_name(ahc), 'A', found); + } else { + /* + * Leave the selection hardware off in case + * this abort attempt will affect yet to + * be sent commands. + */ + ahc_outb(ahc, SCSISEQ, + ahc_inb(ahc, SCSISEQ) & ~ENSELO); + ahc_assert_atn(ahc); + ahc_outb(ahc, MSG_OUT, HOST_MSG); + if (scb == NULL) { + ahc_print_devinfo(ahc, &devinfo); + ahc->msgout_buf[0] = MSG_ABORT_TASK; + ahc->msgout_len = 1; + ahc->msgout_index = 0; + ahc->msg_type = MSG_TYPE_INITIATOR_MSGOUT; + } else { + ahc_print_path(ahc, scb); + scb->flags |= SCB_ABORT; + } + printk("Protocol violation %s. Attempting to abort.\n", + ahc_lookup_phase_entry(curphase)->phasemsg); + } +} + +/* + * Manual message loop handler. + */ +static void +ahc_handle_message_phase(struct ahc_softc *ahc) +{ + struct ahc_devinfo devinfo; + u_int bus_phase; + int end_session; + + ahc_fetch_devinfo(ahc, &devinfo); + end_session = FALSE; + bus_phase = ahc_inb(ahc, SCSISIGI) & PHASE_MASK; + +reswitch: + switch (ahc->msg_type) { + case MSG_TYPE_INITIATOR_MSGOUT: + { + int lastbyte; + int phasemis; + int msgdone; + + if (ahc->msgout_len == 0) + panic("HOST_MSG_LOOP interrupt with no active message"); + +#ifdef AHC_DEBUG + if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) { + ahc_print_devinfo(ahc, &devinfo); + printk("INITIATOR_MSG_OUT"); + } +#endif + phasemis = bus_phase != P_MESGOUT; + if (phasemis) { +#ifdef AHC_DEBUG + if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) { + printk(" PHASEMIS %s\n", + ahc_lookup_phase_entry(bus_phase) + ->phasemsg); + } +#endif + if (bus_phase == P_MESGIN) { + /* + * Change gears and see if + * this messages is of interest to + * us or should be passed back to + * the sequencer. + */ + ahc_outb(ahc, CLRSINT1, CLRATNO); + ahc->send_msg_perror = FALSE; + ahc->msg_type = MSG_TYPE_INITIATOR_MSGIN; + ahc->msgin_index = 0; + goto reswitch; + } + end_session = TRUE; + break; + } + + if (ahc->send_msg_perror) { + ahc_outb(ahc, CLRSINT1, CLRATNO); + ahc_outb(ahc, CLRSINT1, CLRREQINIT); +#ifdef AHC_DEBUG + if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) + printk(" byte 0x%x\n", ahc->send_msg_perror); +#endif + ahc_outb(ahc, SCSIDATL, MSG_PARITY_ERROR); + break; + } + + msgdone = ahc->msgout_index == ahc->msgout_len; + if (msgdone) { + /* + * The target has requested a retry. + * Re-assert ATN, reset our message index to + * 0, and try again. + */ + ahc->msgout_index = 0; + ahc_assert_atn(ahc); + } + + lastbyte = ahc->msgout_index == (ahc->msgout_len - 1); + if (lastbyte) { + /* Last byte is signified by dropping ATN */ + ahc_outb(ahc, CLRSINT1, CLRATNO); + } + + /* + * Clear our interrupt status and present + * the next byte on the bus. + */ + ahc_outb(ahc, CLRSINT1, CLRREQINIT); +#ifdef AHC_DEBUG + if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) + printk(" byte 0x%x\n", + ahc->msgout_buf[ahc->msgout_index]); +#endif + ahc_outb(ahc, SCSIDATL, ahc->msgout_buf[ahc->msgout_index++]); + break; + } + case MSG_TYPE_INITIATOR_MSGIN: + { + int phasemis; + int message_done; + +#ifdef AHC_DEBUG + if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) { + ahc_print_devinfo(ahc, &devinfo); + printk("INITIATOR_MSG_IN"); + } +#endif + phasemis = bus_phase != P_MESGIN; + if (phasemis) { +#ifdef AHC_DEBUG + if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) { + printk(" PHASEMIS %s\n", + ahc_lookup_phase_entry(bus_phase) + ->phasemsg); + } +#endif + ahc->msgin_index = 0; + if (bus_phase == P_MESGOUT + && (ahc->send_msg_perror == TRUE + || (ahc->msgout_len != 0 + && ahc->msgout_index == 0))) { + ahc->msg_type = MSG_TYPE_INITIATOR_MSGOUT; + goto reswitch; + } + end_session = TRUE; + break; + } + + /* Pull the byte in without acking it */ + ahc->msgin_buf[ahc->msgin_index] = ahc_inb(ahc, SCSIBUSL); +#ifdef AHC_DEBUG + if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) + printk(" byte 0x%x\n", + ahc->msgin_buf[ahc->msgin_index]); +#endif + + message_done = ahc_parse_msg(ahc, &devinfo); + + if (message_done) { + /* + * Clear our incoming message buffer in case there + * is another message following this one. + */ + ahc->msgin_index = 0; + + /* + * If this message illicited a response, + * assert ATN so the target takes us to the + * message out phase. + */ + if (ahc->msgout_len != 0) { +#ifdef AHC_DEBUG + if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) { + ahc_print_devinfo(ahc, &devinfo); + printk("Asserting ATN for response\n"); + } +#endif + ahc_assert_atn(ahc); + } + } else + ahc->msgin_index++; + + if (message_done == MSGLOOP_TERMINATED) { + end_session = TRUE; + } else { + /* Ack the byte */ + ahc_outb(ahc, CLRSINT1, CLRREQINIT); + ahc_inb(ahc, SCSIDATL); + } + break; + } + case MSG_TYPE_TARGET_MSGIN: + { + int msgdone; + int msgout_request; + + if (ahc->msgout_len == 0) + panic("Target MSGIN with no active message"); + + /* + * If we interrupted a mesgout session, the initiator + * will not know this until our first REQ. So, we + * only honor mesgout requests after we've sent our + * first byte. + */ + if ((ahc_inb(ahc, SCSISIGI) & ATNI) != 0 + && ahc->msgout_index > 0) + msgout_request = TRUE; + else + msgout_request = FALSE; + + if (msgout_request) { + + /* + * Change gears and see if + * this messages is of interest to + * us or should be passed back to + * the sequencer. + */ + ahc->msg_type = MSG_TYPE_TARGET_MSGOUT; + ahc_outb(ahc, SCSISIGO, P_MESGOUT | BSYO); + ahc->msgin_index = 0; + /* Dummy read to REQ for first byte */ + ahc_inb(ahc, SCSIDATL); + ahc_outb(ahc, SXFRCTL0, + ahc_inb(ahc, SXFRCTL0) | SPIOEN); + break; + } + + msgdone = ahc->msgout_index == ahc->msgout_len; + if (msgdone) { + ahc_outb(ahc, SXFRCTL0, + ahc_inb(ahc, SXFRCTL0) & ~SPIOEN); + end_session = TRUE; + break; + } + + /* + * Present the next byte on the bus. + */ + ahc_outb(ahc, SXFRCTL0, ahc_inb(ahc, SXFRCTL0) | SPIOEN); + ahc_outb(ahc, SCSIDATL, ahc->msgout_buf[ahc->msgout_index++]); + break; + } + case MSG_TYPE_TARGET_MSGOUT: + { + int lastbyte; + int msgdone; + + /* + * The initiator signals that this is + * the last byte by dropping ATN. + */ + lastbyte = (ahc_inb(ahc, SCSISIGI) & ATNI) == 0; + + /* + * Read the latched byte, but turn off SPIOEN first + * so that we don't inadvertently cause a REQ for the + * next byte. + */ + ahc_outb(ahc, SXFRCTL0, ahc_inb(ahc, SXFRCTL0) & ~SPIOEN); + ahc->msgin_buf[ahc->msgin_index] = ahc_inb(ahc, SCSIDATL); + msgdone = ahc_parse_msg(ahc, &devinfo); + if (msgdone == MSGLOOP_TERMINATED) { + /* + * The message is *really* done in that it caused + * us to go to bus free. The sequencer has already + * been reset at this point, so pull the ejection + * handle. + */ + return; + } + + ahc->msgin_index++; + + /* + * XXX Read spec about initiator dropping ATN too soon + * and use msgdone to detect it. + */ + if (msgdone == MSGLOOP_MSGCOMPLETE) { + ahc->msgin_index = 0; + + /* + * If this message illicited a response, transition + * to the Message in phase and send it. + */ + if (ahc->msgout_len != 0) { + ahc_outb(ahc, SCSISIGO, P_MESGIN | BSYO); + ahc_outb(ahc, SXFRCTL0, + ahc_inb(ahc, SXFRCTL0) | SPIOEN); + ahc->msg_type = MSG_TYPE_TARGET_MSGIN; + ahc->msgin_index = 0; + break; + } + } + + if (lastbyte) + end_session = TRUE; + else { + /* Ask for the next byte. */ + ahc_outb(ahc, SXFRCTL0, + ahc_inb(ahc, SXFRCTL0) | SPIOEN); + } + + break; + } + default: + panic("Unknown REQINIT message type"); + } + + if (end_session) { + ahc_clear_msg_state(ahc); + ahc_outb(ahc, RETURN_1, EXIT_MSG_LOOP); + } else + ahc_outb(ahc, RETURN_1, CONT_MSG_LOOP); +} + +/* + * See if we sent a particular extended message to the target. + * If "full" is true, return true only if the target saw the full + * message. If "full" is false, return true if the target saw at + * least the first byte of the message. + */ +static int +ahc_sent_msg(struct ahc_softc *ahc, ahc_msgtype type, u_int msgval, int full) +{ + int found; + u_int index; + + found = FALSE; + index = 0; + + while (index < ahc->msgout_len) { + if (ahc->msgout_buf[index] == MSG_EXTENDED) { + u_int end_index; + + end_index = index + 1 + ahc->msgout_buf[index + 1]; + if (ahc->msgout_buf[index+2] == msgval + && type == AHCMSG_EXT) { + + if (full) { + if (ahc->msgout_index > end_index) + found = TRUE; + } else if (ahc->msgout_index > index) + found = TRUE; + } + index = end_index; + } else if (ahc->msgout_buf[index] >= MSG_SIMPLE_TASK + && ahc->msgout_buf[index] <= MSG_IGN_WIDE_RESIDUE) { + + /* Skip tag type and tag id or residue param*/ + index += 2; + } else { + /* Single byte message */ + if (type == AHCMSG_1B + && ahc->msgout_buf[index] == msgval + && ahc->msgout_index > index) + found = TRUE; + index++; + } + + if (found) + break; + } + return (found); +} + +/* + * Wait for a complete incoming message, parse it, and respond accordingly. + */ +static int +ahc_parse_msg(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) +{ + struct ahc_initiator_tinfo *tinfo; + struct ahc_tmode_tstate *tstate; + int reject; + int done; + int response; + u_int targ_scsirate; + + done = MSGLOOP_IN_PROG; + response = FALSE; + reject = FALSE; + tinfo = ahc_fetch_transinfo(ahc, devinfo->channel, devinfo->our_scsiid, + devinfo->target, &tstate); + targ_scsirate = tinfo->scsirate; + + /* + * Parse as much of the message as is available, + * rejecting it if we don't support it. When + * the entire message is available and has been + * handled, return MSGLOOP_MSGCOMPLETE, indicating + * that we have parsed an entire message. + * + * In the case of extended messages, we accept the length + * byte outright and perform more checking once we know the + * extended message type. + */ + switch (ahc->msgin_buf[0]) { + case MSG_DISCONNECT: + case MSG_SAVEDATAPOINTER: + case MSG_CMDCOMPLETE: + case MSG_RESTOREPOINTERS: + case MSG_IGN_WIDE_RESIDUE: + /* + * End our message loop as these are messages + * the sequencer handles on its own. + */ + done = MSGLOOP_TERMINATED; + break; + case MSG_MESSAGE_REJECT: + response = ahc_handle_msg_reject(ahc, devinfo); + fallthrough; + case MSG_NOOP: + done = MSGLOOP_MSGCOMPLETE; + break; + case MSG_EXTENDED: + { + /* Wait for enough of the message to begin validation */ + if (ahc->msgin_index < 2) + break; + switch (ahc->msgin_buf[2]) { + case MSG_EXT_SDTR: + { + const struct ahc_syncrate *syncrate; + u_int period; + u_int ppr_options; + u_int offset; + u_int saved_offset; + + if (ahc->msgin_buf[1] != MSG_EXT_SDTR_LEN) { + reject = TRUE; + break; + } + + /* + * Wait until we have both args before validating + * and acting on this message. + * + * Add one to MSG_EXT_SDTR_LEN to account for + * the extended message preamble. + */ + if (ahc->msgin_index < (MSG_EXT_SDTR_LEN + 1)) + break; + + period = ahc->msgin_buf[3]; + ppr_options = 0; + saved_offset = offset = ahc->msgin_buf[4]; + syncrate = ahc_devlimited_syncrate(ahc, tinfo, &period, + &ppr_options, + devinfo->role); + ahc_validate_offset(ahc, tinfo, syncrate, &offset, + targ_scsirate & WIDEXFER, + devinfo->role); + if (bootverbose) { + printk("(%s:%c:%d:%d): Received " + "SDTR period %x, offset %x\n\t" + "Filtered to period %x, offset %x\n", + ahc_name(ahc), devinfo->channel, + devinfo->target, devinfo->lun, + ahc->msgin_buf[3], saved_offset, + period, offset); + } + ahc_set_syncrate(ahc, devinfo, + syncrate, period, + offset, ppr_options, + AHC_TRANS_ACTIVE|AHC_TRANS_GOAL, + /*paused*/TRUE); + + /* + * See if we initiated Sync Negotiation + * and didn't have to fall down to async + * transfers. + */ + if (ahc_sent_msg(ahc, AHCMSG_EXT, MSG_EXT_SDTR, TRUE)) { + /* We started it */ + if (saved_offset != offset) { + /* Went too low - force async */ + reject = TRUE; + } + } else { + /* + * Send our own SDTR in reply + */ + if (bootverbose + && devinfo->role == ROLE_INITIATOR) { + printk("(%s:%c:%d:%d): Target " + "Initiated SDTR\n", + ahc_name(ahc), devinfo->channel, + devinfo->target, devinfo->lun); + } + ahc->msgout_index = 0; + ahc->msgout_len = 0; + ahc_construct_sdtr(ahc, devinfo, + period, offset); + ahc->msgout_index = 0; + response = TRUE; + } + done = MSGLOOP_MSGCOMPLETE; + break; + } + case MSG_EXT_WDTR: + { + u_int bus_width; + u_int saved_width; + u_int sending_reply; + + sending_reply = FALSE; + if (ahc->msgin_buf[1] != MSG_EXT_WDTR_LEN) { + reject = TRUE; + break; + } + + /* + * Wait until we have our arg before validating + * and acting on this message. + * + * Add one to MSG_EXT_WDTR_LEN to account for + * the extended message preamble. + */ + if (ahc->msgin_index < (MSG_EXT_WDTR_LEN + 1)) + break; + + bus_width = ahc->msgin_buf[3]; + saved_width = bus_width; + ahc_validate_width(ahc, tinfo, &bus_width, + devinfo->role); + if (bootverbose) { + printk("(%s:%c:%d:%d): Received WDTR " + "%x filtered to %x\n", + ahc_name(ahc), devinfo->channel, + devinfo->target, devinfo->lun, + saved_width, bus_width); + } + + if (ahc_sent_msg(ahc, AHCMSG_EXT, MSG_EXT_WDTR, TRUE)) { + /* + * Don't send a WDTR back to the + * target, since we asked first. + * If the width went higher than our + * request, reject it. + */ + if (saved_width > bus_width) { + reject = TRUE; + printk("(%s:%c:%d:%d): requested %dBit " + "transfers. Rejecting...\n", + ahc_name(ahc), devinfo->channel, + devinfo->target, devinfo->lun, + 8 * (0x01 << bus_width)); + bus_width = 0; + } + } else { + /* + * Send our own WDTR in reply + */ + if (bootverbose + && devinfo->role == ROLE_INITIATOR) { + printk("(%s:%c:%d:%d): Target " + "Initiated WDTR\n", + ahc_name(ahc), devinfo->channel, + devinfo->target, devinfo->lun); + } + ahc->msgout_index = 0; + ahc->msgout_len = 0; + ahc_construct_wdtr(ahc, devinfo, bus_width); + ahc->msgout_index = 0; + response = TRUE; + sending_reply = TRUE; + } + /* + * After a wide message, we are async, but + * some devices don't seem to honor this portion + * of the spec. Force a renegotiation of the + * sync component of our transfer agreement even + * if our goal is async. By updating our width + * after forcing the negotiation, we avoid + * renegotiating for width. + */ + ahc_update_neg_request(ahc, devinfo, tstate, + tinfo, AHC_NEG_ALWAYS); + ahc_set_width(ahc, devinfo, bus_width, + AHC_TRANS_ACTIVE|AHC_TRANS_GOAL, + /*paused*/TRUE); + if (sending_reply == FALSE && reject == FALSE) { + + /* + * We will always have an SDTR to send. + */ + ahc->msgout_index = 0; + ahc->msgout_len = 0; + ahc_build_transfer_msg(ahc, devinfo); + ahc->msgout_index = 0; + response = TRUE; + } + done = MSGLOOP_MSGCOMPLETE; + break; + } + case MSG_EXT_PPR: + { + const struct ahc_syncrate *syncrate; + u_int period; + u_int offset; + u_int bus_width; + u_int ppr_options; + u_int saved_width; + u_int saved_offset; + u_int saved_ppr_options; + + if (ahc->msgin_buf[1] != MSG_EXT_PPR_LEN) { + reject = TRUE; + break; + } + + /* + * Wait until we have all args before validating + * and acting on this message. + * + * Add one to MSG_EXT_PPR_LEN to account for + * the extended message preamble. + */ + if (ahc->msgin_index < (MSG_EXT_PPR_LEN + 1)) + break; + + period = ahc->msgin_buf[3]; + offset = ahc->msgin_buf[5]; + bus_width = ahc->msgin_buf[6]; + saved_width = bus_width; + ppr_options = ahc->msgin_buf[7]; + /* + * According to the spec, a DT only + * period factor with no DT option + * set implies async. + */ + if ((ppr_options & MSG_EXT_PPR_DT_REQ) == 0 + && period == 9) + offset = 0; + saved_ppr_options = ppr_options; + saved_offset = offset; + + /* + * Mask out any options we don't support + * on any controller. Transfer options are + * only available if we are negotiating wide. + */ + ppr_options &= MSG_EXT_PPR_DT_REQ; + if (bus_width == 0) + ppr_options = 0; + + ahc_validate_width(ahc, tinfo, &bus_width, + devinfo->role); + syncrate = ahc_devlimited_syncrate(ahc, tinfo, &period, + &ppr_options, + devinfo->role); + ahc_validate_offset(ahc, tinfo, syncrate, + &offset, bus_width, + devinfo->role); + + if (ahc_sent_msg(ahc, AHCMSG_EXT, MSG_EXT_PPR, TRUE)) { + /* + * If we are unable to do any of the + * requested options (we went too low), + * then we'll have to reject the message. + */ + if (saved_width > bus_width + || saved_offset != offset + || saved_ppr_options != ppr_options) { + reject = TRUE; + period = 0; + offset = 0; + bus_width = 0; + ppr_options = 0; + syncrate = NULL; + } + } else { + if (devinfo->role != ROLE_TARGET) + printk("(%s:%c:%d:%d): Target " + "Initiated PPR\n", + ahc_name(ahc), devinfo->channel, + devinfo->target, devinfo->lun); + else + printk("(%s:%c:%d:%d): Initiator " + "Initiated PPR\n", + ahc_name(ahc), devinfo->channel, + devinfo->target, devinfo->lun); + ahc->msgout_index = 0; + ahc->msgout_len = 0; + ahc_construct_ppr(ahc, devinfo, period, offset, + bus_width, ppr_options); + ahc->msgout_index = 0; + response = TRUE; + } + if (bootverbose) { + printk("(%s:%c:%d:%d): Received PPR width %x, " + "period %x, offset %x,options %x\n" + "\tFiltered to width %x, period %x, " + "offset %x, options %x\n", + ahc_name(ahc), devinfo->channel, + devinfo->target, devinfo->lun, + saved_width, ahc->msgin_buf[3], + saved_offset, saved_ppr_options, + bus_width, period, offset, ppr_options); + } + ahc_set_width(ahc, devinfo, bus_width, + AHC_TRANS_ACTIVE|AHC_TRANS_GOAL, + /*paused*/TRUE); + ahc_set_syncrate(ahc, devinfo, + syncrate, period, + offset, ppr_options, + AHC_TRANS_ACTIVE|AHC_TRANS_GOAL, + /*paused*/TRUE); + done = MSGLOOP_MSGCOMPLETE; + break; + } + default: + /* Unknown extended message. Reject it. */ + reject = TRUE; + break; + } + break; + } +#ifdef AHC_TARGET_MODE + case MSG_BUS_DEV_RESET: + ahc_handle_devreset(ahc, devinfo, + CAM_BDR_SENT, + "Bus Device Reset Received", + /*verbose_level*/0); + ahc_restart(ahc); + done = MSGLOOP_TERMINATED; + break; + case MSG_ABORT_TAG: + case MSG_ABORT: + case MSG_CLEAR_QUEUE: + { + int tag; + + /* Target mode messages */ + if (devinfo->role != ROLE_TARGET) { + reject = TRUE; + break; + } + tag = SCB_LIST_NULL; + if (ahc->msgin_buf[0] == MSG_ABORT_TAG) + tag = ahc_inb(ahc, INITIATOR_TAG); + ahc_abort_scbs(ahc, devinfo->target, devinfo->channel, + devinfo->lun, tag, ROLE_TARGET, + CAM_REQ_ABORTED); + + tstate = ahc->enabled_targets[devinfo->our_scsiid]; + if (tstate != NULL) { + struct ahc_tmode_lstate* lstate; + + lstate = tstate->enabled_luns[devinfo->lun]; + if (lstate != NULL) { + ahc_queue_lstate_event(ahc, lstate, + devinfo->our_scsiid, + ahc->msgin_buf[0], + /*arg*/tag); + ahc_send_lstate_events(ahc, lstate); + } + } + ahc_restart(ahc); + done = MSGLOOP_TERMINATED; + break; + } +#endif + case MSG_TERM_IO_PROC: + default: + reject = TRUE; + break; + } + + if (reject) { + /* + * Setup to reject the message. + */ + ahc->msgout_index = 0; + ahc->msgout_len = 1; + ahc->msgout_buf[0] = MSG_MESSAGE_REJECT; + done = MSGLOOP_MSGCOMPLETE; + response = TRUE; + } + + if (done != MSGLOOP_IN_PROG && !response) + /* Clear the outgoing message buffer */ + ahc->msgout_len = 0; + + return (done); +} + +/* + * Process a message reject message. + */ +static int +ahc_handle_msg_reject(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) +{ + /* + * What we care about here is if we had an + * outstanding SDTR or WDTR message for this + * target. If we did, this is a signal that + * the target is refusing negotiation. + */ + struct scb *scb; + struct ahc_initiator_tinfo *tinfo; + struct ahc_tmode_tstate *tstate; + u_int scb_index; + u_int last_msg; + int response = 0; + + scb_index = ahc_inb(ahc, SCB_TAG); + scb = ahc_lookup_scb(ahc, scb_index); + tinfo = ahc_fetch_transinfo(ahc, devinfo->channel, + devinfo->our_scsiid, + devinfo->target, &tstate); + /* Might be necessary */ + last_msg = ahc_inb(ahc, LAST_MSG); + + if (ahc_sent_msg(ahc, AHCMSG_EXT, MSG_EXT_PPR, /*full*/FALSE)) { + /* + * Target does not support the PPR message. + * Attempt to negotiate SPI-2 style. + */ + if (bootverbose) { + printk("(%s:%c:%d:%d): PPR Rejected. " + "Trying WDTR/SDTR\n", + ahc_name(ahc), devinfo->channel, + devinfo->target, devinfo->lun); + } + tinfo->goal.ppr_options = 0; + tinfo->curr.transport_version = 2; + tinfo->goal.transport_version = 2; + ahc->msgout_index = 0; + ahc->msgout_len = 0; + ahc_build_transfer_msg(ahc, devinfo); + ahc->msgout_index = 0; + response = 1; + } else if (ahc_sent_msg(ahc, AHCMSG_EXT, MSG_EXT_WDTR, /*full*/FALSE)) { + + /* note 8bit xfers */ + printk("(%s:%c:%d:%d): refuses WIDE negotiation. Using " + "8bit transfers\n", ahc_name(ahc), + devinfo->channel, devinfo->target, devinfo->lun); + ahc_set_width(ahc, devinfo, MSG_EXT_WDTR_BUS_8_BIT, + AHC_TRANS_ACTIVE|AHC_TRANS_GOAL, + /*paused*/TRUE); + /* + * No need to clear the sync rate. If the target + * did not accept the command, our syncrate is + * unaffected. If the target started the negotiation, + * but rejected our response, we already cleared the + * sync rate before sending our WDTR. + */ + if (tinfo->goal.offset != tinfo->curr.offset) { + + /* Start the sync negotiation */ + ahc->msgout_index = 0; + ahc->msgout_len = 0; + ahc_build_transfer_msg(ahc, devinfo); + ahc->msgout_index = 0; + response = 1; + } + } else if (ahc_sent_msg(ahc, AHCMSG_EXT, MSG_EXT_SDTR, /*full*/FALSE)) { + /* note asynch xfers and clear flag */ + ahc_set_syncrate(ahc, devinfo, /*syncrate*/NULL, /*period*/0, + /*offset*/0, /*ppr_options*/0, + AHC_TRANS_ACTIVE|AHC_TRANS_GOAL, + /*paused*/TRUE); + printk("(%s:%c:%d:%d): refuses synchronous negotiation. " + "Using asynchronous transfers\n", + ahc_name(ahc), devinfo->channel, + devinfo->target, devinfo->lun); + } else if ((scb->hscb->control & MSG_SIMPLE_TASK) != 0) { + int tag_type; + int mask; + + tag_type = (scb->hscb->control & MSG_SIMPLE_TASK); + + if (tag_type == MSG_SIMPLE_TASK) { + printk("(%s:%c:%d:%d): refuses tagged commands. " + "Performing non-tagged I/O\n", ahc_name(ahc), + devinfo->channel, devinfo->target, devinfo->lun); + ahc_set_tags(ahc, scb->io_ctx, devinfo, AHC_QUEUE_NONE); + mask = ~0x23; + } else { + printk("(%s:%c:%d:%d): refuses %s tagged commands. " + "Performing simple queue tagged I/O only\n", + ahc_name(ahc), devinfo->channel, devinfo->target, + devinfo->lun, tag_type == MSG_ORDERED_TASK + ? "ordered" : "head of queue"); + ahc_set_tags(ahc, scb->io_ctx, devinfo, AHC_QUEUE_BASIC); + mask = ~0x03; + } + + /* + * Resend the identify for this CCB as the target + * may believe that the selection is invalid otherwise. + */ + ahc_outb(ahc, SCB_CONTROL, + ahc_inb(ahc, SCB_CONTROL) & mask); + scb->hscb->control &= mask; + ahc_set_transaction_tag(scb, /*enabled*/FALSE, + /*type*/MSG_SIMPLE_TASK); + ahc_outb(ahc, MSG_OUT, MSG_IDENTIFYFLAG); + ahc_assert_atn(ahc); + + /* + * This transaction is now at the head of + * the untagged queue for this target. + */ + if ((ahc->flags & AHC_SCB_BTT) == 0) { + struct scb_tailq *untagged_q; + + untagged_q = + &(ahc->untagged_queues[devinfo->target_offset]); + TAILQ_INSERT_HEAD(untagged_q, scb, links.tqe); + scb->flags |= SCB_UNTAGGEDQ; + } + ahc_busy_tcl(ahc, BUILD_TCL(scb->hscb->scsiid, devinfo->lun), + scb->hscb->tag); + + /* + * Requeue all tagged commands for this target + * currently in our possession so they can be + * converted to untagged commands. + */ + ahc_search_qinfifo(ahc, SCB_GET_TARGET(ahc, scb), + SCB_GET_CHANNEL(ahc, scb), + SCB_GET_LUN(scb), /*tag*/SCB_LIST_NULL, + ROLE_INITIATOR, CAM_REQUEUE_REQ, + SEARCH_COMPLETE); + } else { + /* + * Otherwise, we ignore it. + */ + printk("%s:%c:%d: Message reject for %x -- ignored\n", + ahc_name(ahc), devinfo->channel, devinfo->target, + last_msg); + } + return (response); +} + +/* + * Process an ingnore wide residue message. + */ +static void +ahc_handle_ign_wide_residue(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) +{ + u_int scb_index; + struct scb *scb; + + scb_index = ahc_inb(ahc, SCB_TAG); + scb = ahc_lookup_scb(ahc, scb_index); + /* + * XXX Actually check data direction in the sequencer? + * Perhaps add datadir to some spare bits in the hscb? + */ + if ((ahc_inb(ahc, SEQ_FLAGS) & DPHASE) == 0 + || ahc_get_transfer_dir(scb) != CAM_DIR_IN) { + /* + * Ignore the message if we haven't + * seen an appropriate data phase yet. + */ + } else { + /* + * If the residual occurred on the last + * transfer and the transfer request was + * expected to end on an odd count, do + * nothing. Otherwise, subtract a byte + * and update the residual count accordingly. + */ + uint32_t sgptr; + + sgptr = ahc_inb(ahc, SCB_RESIDUAL_SGPTR); + if ((sgptr & SG_LIST_NULL) != 0 + && (ahc_inb(ahc, SCB_LUN) & SCB_XFERLEN_ODD) != 0) { + /* + * If the residual occurred on the last + * transfer and the transfer request was + * expected to end on an odd count, do + * nothing. + */ + } else { + struct ahc_dma_seg *sg; + uint32_t data_cnt; + uint32_t data_addr; + uint32_t sglen; + + /* Pull in all of the sgptr */ + sgptr = ahc_inl(ahc, SCB_RESIDUAL_SGPTR); + data_cnt = ahc_inl(ahc, SCB_RESIDUAL_DATACNT); + + if ((sgptr & SG_LIST_NULL) != 0) { + /* + * The residual data count is not updated + * for the command run to completion case. + * Explicitly zero the count. + */ + data_cnt &= ~AHC_SG_LEN_MASK; + } + + data_addr = ahc_inl(ahc, SHADDR); + + data_cnt += 1; + data_addr -= 1; + sgptr &= SG_PTR_MASK; + + sg = ahc_sg_bus_to_virt(scb, sgptr); + + /* + * The residual sg ptr points to the next S/G + * to load so we must go back one. + */ + sg--; + sglen = ahc_le32toh(sg->len) & AHC_SG_LEN_MASK; + if (sg != scb->sg_list + && sglen < (data_cnt & AHC_SG_LEN_MASK)) { + + sg--; + sglen = ahc_le32toh(sg->len); + /* + * Preserve High Address and SG_LIST bits + * while setting the count to 1. + */ + data_cnt = 1 | (sglen & (~AHC_SG_LEN_MASK)); + data_addr = ahc_le32toh(sg->addr) + + (sglen & AHC_SG_LEN_MASK) - 1; + + /* + * Increment sg so it points to the + * "next" sg. + */ + sg++; + sgptr = ahc_sg_virt_to_bus(scb, sg); + } + ahc_outl(ahc, SCB_RESIDUAL_SGPTR, sgptr); + ahc_outl(ahc, SCB_RESIDUAL_DATACNT, data_cnt); + /* + * Toggle the "oddness" of the transfer length + * to handle this mid-transfer ignore wide + * residue. This ensures that the oddness is + * correct for subsequent data transfers. + */ + ahc_outb(ahc, SCB_LUN, + ahc_inb(ahc, SCB_LUN) ^ SCB_XFERLEN_ODD); + } + } +} + + +/* + * Reinitialize the data pointers for the active transfer + * based on its current residual. + */ +static void +ahc_reinitialize_dataptrs(struct ahc_softc *ahc) +{ + struct scb *scb; + struct ahc_dma_seg *sg; + u_int scb_index; + uint32_t sgptr; + uint32_t resid; + uint32_t dataptr; + + scb_index = ahc_inb(ahc, SCB_TAG); + scb = ahc_lookup_scb(ahc, scb_index); + sgptr = (ahc_inb(ahc, SCB_RESIDUAL_SGPTR + 3) << 24) + | (ahc_inb(ahc, SCB_RESIDUAL_SGPTR + 2) << 16) + | (ahc_inb(ahc, SCB_RESIDUAL_SGPTR + 1) << 8) + | ahc_inb(ahc, SCB_RESIDUAL_SGPTR); + + sgptr &= SG_PTR_MASK; + sg = ahc_sg_bus_to_virt(scb, sgptr); + + /* The residual sg_ptr always points to the next sg */ + sg--; + + resid = (ahc_inb(ahc, SCB_RESIDUAL_DATACNT + 2) << 16) + | (ahc_inb(ahc, SCB_RESIDUAL_DATACNT + 1) << 8) + | ahc_inb(ahc, SCB_RESIDUAL_DATACNT); + + dataptr = ahc_le32toh(sg->addr) + + (ahc_le32toh(sg->len) & AHC_SG_LEN_MASK) + - resid; + if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) { + u_int dscommand1; + + dscommand1 = ahc_inb(ahc, DSCOMMAND1); + ahc_outb(ahc, DSCOMMAND1, dscommand1 | HADDLDSEL0); + ahc_outb(ahc, HADDR, + (ahc_le32toh(sg->len) >> 24) & SG_HIGH_ADDR_BITS); + ahc_outb(ahc, DSCOMMAND1, dscommand1); + } + ahc_outb(ahc, HADDR + 3, dataptr >> 24); + ahc_outb(ahc, HADDR + 2, dataptr >> 16); + ahc_outb(ahc, HADDR + 1, dataptr >> 8); + ahc_outb(ahc, HADDR, dataptr); + ahc_outb(ahc, HCNT + 2, resid >> 16); + ahc_outb(ahc, HCNT + 1, resid >> 8); + ahc_outb(ahc, HCNT, resid); + if ((ahc->features & AHC_ULTRA2) == 0) { + ahc_outb(ahc, STCNT + 2, resid >> 16); + ahc_outb(ahc, STCNT + 1, resid >> 8); + ahc_outb(ahc, STCNT, resid); + } +} + +/* + * Handle the effects of issuing a bus device reset message. + */ +static void +ahc_handle_devreset(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, + cam_status status, char *message, int verbose_level) +{ +#ifdef AHC_TARGET_MODE + struct ahc_tmode_tstate* tstate; + u_int lun; +#endif + int found; + + found = ahc_abort_scbs(ahc, devinfo->target, devinfo->channel, + CAM_LUN_WILDCARD, SCB_LIST_NULL, devinfo->role, + status); + +#ifdef AHC_TARGET_MODE + /* + * Send an immediate notify ccb to all target mord peripheral + * drivers affected by this action. + */ + tstate = ahc->enabled_targets[devinfo->our_scsiid]; + if (tstate != NULL) { + for (lun = 0; lun < AHC_NUM_LUNS; lun++) { + struct ahc_tmode_lstate* lstate; + + lstate = tstate->enabled_luns[lun]; + if (lstate == NULL) + continue; + + ahc_queue_lstate_event(ahc, lstate, devinfo->our_scsiid, + MSG_BUS_DEV_RESET, /*arg*/0); + ahc_send_lstate_events(ahc, lstate); + } + } +#endif + + /* + * Go back to async/narrow transfers and renegotiate. + */ + ahc_set_width(ahc, devinfo, MSG_EXT_WDTR_BUS_8_BIT, + AHC_TRANS_CUR, /*paused*/TRUE); + ahc_set_syncrate(ahc, devinfo, /*syncrate*/NULL, + /*period*/0, /*offset*/0, /*ppr_options*/0, + AHC_TRANS_CUR, /*paused*/TRUE); + + if (status != CAM_SEL_TIMEOUT) + ahc_send_async(ahc, devinfo->channel, devinfo->target, + CAM_LUN_WILDCARD, AC_SENT_BDR); + + if (message != NULL + && (verbose_level <= bootverbose)) + printk("%s: %s on %c:%d. %d SCBs aborted\n", ahc_name(ahc), + message, devinfo->channel, devinfo->target, found); +} + +#ifdef AHC_TARGET_MODE +static void +ahc_setup_target_msgin(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, + struct scb *scb) +{ + + /* + * To facilitate adding multiple messages together, + * each routine should increment the index and len + * variables instead of setting them explicitly. + */ + ahc->msgout_index = 0; + ahc->msgout_len = 0; + + if (scb != NULL && (scb->flags & SCB_AUTO_NEGOTIATE) != 0) + ahc_build_transfer_msg(ahc, devinfo); + else + panic("ahc_intr: AWAITING target message with no message"); + + ahc->msgout_index = 0; + ahc->msg_type = MSG_TYPE_TARGET_MSGIN; +} +#endif +/**************************** Initialization **********************************/ +/* + * Allocate a controller structure for a new device + * and perform initial initializion. + */ +struct ahc_softc * +ahc_alloc(void *platform_arg, char *name) +{ + struct ahc_softc *ahc; + int i; + + ahc = kzalloc(sizeof(*ahc), GFP_ATOMIC); + if (!ahc) { + printk("aic7xxx: cannot malloc softc!\n"); + kfree(name); + return NULL; + } + + ahc->seep_config = kmalloc(sizeof(*ahc->seep_config), GFP_ATOMIC); + if (ahc->seep_config == NULL) { + kfree(ahc); + kfree(name); + return (NULL); + } + LIST_INIT(&ahc->pending_scbs); + /* We don't know our unit number until the OSM sets it */ + ahc->name = name; + ahc->unit = -1; + ahc->description = NULL; + ahc->channel = 'A'; + ahc->channel_b = 'B'; + ahc->chip = AHC_NONE; + ahc->features = AHC_FENONE; + ahc->bugs = AHC_BUGNONE; + ahc->flags = AHC_FNONE; + /* + * Default to all error reporting enabled with the + * sequencer operating at its fastest speed. + * The bus attach code may modify this. + */ + ahc->seqctl = FASTMODE; + + for (i = 0; i < AHC_NUM_TARGETS; i++) + TAILQ_INIT(&ahc->untagged_queues[i]); + if (ahc_platform_alloc(ahc, platform_arg) != 0) { + ahc_free(ahc); + ahc = NULL; + } + return (ahc); +} + +int +ahc_softc_init(struct ahc_softc *ahc) +{ + + /* The IRQMS bit is only valid on VL and EISA chips */ + if ((ahc->chip & AHC_PCI) == 0) + ahc->unpause = ahc_inb(ahc, HCNTRL) & IRQMS; + else + ahc->unpause = 0; + ahc->pause = ahc->unpause | PAUSE; + /* XXX The shared scb data stuff should be deprecated */ + if (ahc->scb_data == NULL) { + ahc->scb_data = kzalloc(sizeof(*ahc->scb_data), GFP_ATOMIC); + if (ahc->scb_data == NULL) + return (ENOMEM); + } + + return (0); +} + +void +ahc_set_unit(struct ahc_softc *ahc, int unit) +{ + ahc->unit = unit; +} + +void +ahc_set_name(struct ahc_softc *ahc, char *name) +{ + kfree(ahc->name); + ahc->name = name; +} + +void +ahc_free(struct ahc_softc *ahc) +{ + int i; + + switch (ahc->init_level) { + default: + case 5: + ahc_shutdown(ahc); + fallthrough; + case 4: + ahc_dmamap_unload(ahc, ahc->shared_data_dmat, + ahc->shared_data_dmamap); + fallthrough; + case 3: + ahc_dmamem_free(ahc, ahc->shared_data_dmat, ahc->qoutfifo, + ahc->shared_data_dmamap); + ahc_dmamap_destroy(ahc, ahc->shared_data_dmat, + ahc->shared_data_dmamap); + fallthrough; + case 2: + ahc_dma_tag_destroy(ahc, ahc->shared_data_dmat); + case 1: + break; + case 0: + break; + } + + ahc_platform_free(ahc); + ahc_fini_scbdata(ahc); + for (i = 0; i < AHC_NUM_TARGETS; i++) { + struct ahc_tmode_tstate *tstate; + + tstate = ahc->enabled_targets[i]; + if (tstate != NULL) { +#ifdef AHC_TARGET_MODE + int j; + + for (j = 0; j < AHC_NUM_LUNS; j++) { + struct ahc_tmode_lstate *lstate; + + lstate = tstate->enabled_luns[j]; + if (lstate != NULL) { + xpt_free_path(lstate->path); + kfree(lstate); + } + } +#endif + kfree(tstate); + } + } +#ifdef AHC_TARGET_MODE + if (ahc->black_hole != NULL) { + xpt_free_path(ahc->black_hole->path); + kfree(ahc->black_hole); + } +#endif + kfree(ahc->name); + kfree(ahc->seep_config); + kfree(ahc); + return; +} + +static void +ahc_shutdown(void *arg) +{ + struct ahc_softc *ahc; + int i; + + ahc = (struct ahc_softc *)arg; + + /* This will reset most registers to 0, but not all */ + ahc_reset(ahc, /*reinit*/FALSE); + ahc_outb(ahc, SCSISEQ, 0); + ahc_outb(ahc, SXFRCTL0, 0); + ahc_outb(ahc, DSPCISTATUS, 0); + + for (i = TARG_SCSIRATE; i < SCSICONF; i++) + ahc_outb(ahc, i, 0); +} + +/* + * Reset the controller and record some information about it + * that is only available just after a reset. If "reinit" is + * non-zero, this reset occurred after initial configuration + * and the caller requests that the chip be fully reinitialized + * to a runable state. Chip interrupts are *not* enabled after + * a reinitialization. The caller must enable interrupts via + * ahc_intr_enable(). + */ +int +ahc_reset(struct ahc_softc *ahc, int reinit) +{ + u_int sblkctl; + u_int sxfrctl1_a, sxfrctl1_b; + int error; + int wait; + + /* + * Preserve the value of the SXFRCTL1 register for all channels. + * It contains settings that affect termination and we don't want + * to disturb the integrity of the bus. + */ + ahc_pause(ahc); + sxfrctl1_b = 0; + if ((ahc->chip & AHC_CHIPID_MASK) == AHC_AIC7770) { + u_int sblkctl; + + /* + * Save channel B's settings in case this chip + * is setup for TWIN channel operation. + */ + sblkctl = ahc_inb(ahc, SBLKCTL); + ahc_outb(ahc, SBLKCTL, sblkctl | SELBUSB); + sxfrctl1_b = ahc_inb(ahc, SXFRCTL1); + ahc_outb(ahc, SBLKCTL, sblkctl & ~SELBUSB); + } + sxfrctl1_a = ahc_inb(ahc, SXFRCTL1); + + ahc_outb(ahc, HCNTRL, CHIPRST | ahc->pause); + + /* + * Ensure that the reset has finished. We delay 1000us + * prior to reading the register to make sure the chip + * has sufficiently completed its reset to handle register + * accesses. + */ + wait = 1000; + do { + ahc_delay(1000); + } while (--wait && !(ahc_inb(ahc, HCNTRL) & CHIPRSTACK)); + + if (wait == 0) { + printk("%s: WARNING - Failed chip reset! " + "Trying to initialize anyway.\n", ahc_name(ahc)); + } + ahc_outb(ahc, HCNTRL, ahc->pause); + + /* Determine channel configuration */ + sblkctl = ahc_inb(ahc, SBLKCTL) & (SELBUSB|SELWIDE); + /* No Twin Channel PCI cards */ + if ((ahc->chip & AHC_PCI) != 0) + sblkctl &= ~SELBUSB; + switch (sblkctl) { + case 0: + /* Single Narrow Channel */ + break; + case 2: + /* Wide Channel */ + ahc->features |= AHC_WIDE; + break; + case 8: + /* Twin Channel */ + ahc->features |= AHC_TWIN; + break; + default: + printk(" Unsupported adapter type. Ignoring\n"); + return(-1); + } + + /* + * Reload sxfrctl1. + * + * We must always initialize STPWEN to 1 before we + * restore the saved values. STPWEN is initialized + * to a tri-state condition which can only be cleared + * by turning it on. + */ + if ((ahc->features & AHC_TWIN) != 0) { + u_int sblkctl; + + sblkctl = ahc_inb(ahc, SBLKCTL); + ahc_outb(ahc, SBLKCTL, sblkctl | SELBUSB); + ahc_outb(ahc, SXFRCTL1, sxfrctl1_b); + ahc_outb(ahc, SBLKCTL, sblkctl & ~SELBUSB); + } + ahc_outb(ahc, SXFRCTL1, sxfrctl1_a); + + error = 0; + if (reinit != 0) + /* + * If a recovery action has forced a chip reset, + * re-initialize the chip to our liking. + */ + error = ahc->bus_chip_init(ahc); +#ifdef AHC_DUMP_SEQ + else + ahc_dumpseq(ahc); +#endif + + return (error); +} + +/* + * Determine the number of SCBs available on the controller + */ +int +ahc_probe_scbs(struct ahc_softc *ahc) { + int i; + + for (i = 0; i < AHC_SCB_MAX; i++) { + + ahc_outb(ahc, SCBPTR, i); + ahc_outb(ahc, SCB_BASE, i); + if (ahc_inb(ahc, SCB_BASE) != i) + break; + ahc_outb(ahc, SCBPTR, 0); + if (ahc_inb(ahc, SCB_BASE) != 0) + break; + } + return (i); +} + +static void +ahc_dmamap_cb(void *arg, bus_dma_segment_t *segs, int nseg, int error) +{ + dma_addr_t *baddr; + + baddr = (dma_addr_t *)arg; + *baddr = segs->ds_addr; +} + +static void +ahc_build_free_scb_list(struct ahc_softc *ahc) +{ + int scbsize; + int i; + + scbsize = 32; + if ((ahc->flags & AHC_LSCBS_ENABLED) != 0) + scbsize = 64; + + for (i = 0; i < ahc->scb_data->maxhscbs; i++) { + int j; + + ahc_outb(ahc, SCBPTR, i); + + /* + * Touch all SCB bytes to avoid parity errors + * should one of our debugging routines read + * an otherwise uninitiatlized byte. + */ + for (j = 0; j < scbsize; j++) + ahc_outb(ahc, SCB_BASE+j, 0xFF); + + /* Clear the control byte. */ + ahc_outb(ahc, SCB_CONTROL, 0); + + /* Set the next pointer */ + if ((ahc->flags & AHC_PAGESCBS) != 0) + ahc_outb(ahc, SCB_NEXT, i+1); + else + ahc_outb(ahc, SCB_NEXT, SCB_LIST_NULL); + + /* Make the tag number, SCSIID, and lun invalid */ + ahc_outb(ahc, SCB_TAG, SCB_LIST_NULL); + ahc_outb(ahc, SCB_SCSIID, 0xFF); + ahc_outb(ahc, SCB_LUN, 0xFF); + } + + if ((ahc->flags & AHC_PAGESCBS) != 0) { + /* SCB 0 heads the free list. */ + ahc_outb(ahc, FREE_SCBH, 0); + } else { + /* No free list. */ + ahc_outb(ahc, FREE_SCBH, SCB_LIST_NULL); + } + + /* Make sure that the last SCB terminates the free list */ + ahc_outb(ahc, SCBPTR, i-1); + ahc_outb(ahc, SCB_NEXT, SCB_LIST_NULL); +} + +static int +ahc_init_scbdata(struct ahc_softc *ahc) +{ + struct scb_data *scb_data; + + scb_data = ahc->scb_data; + SLIST_INIT(&scb_data->free_scbs); + SLIST_INIT(&scb_data->sg_maps); + + /* Allocate SCB resources */ + scb_data->scbarray = kcalloc(AHC_SCB_MAX_ALLOC, sizeof(struct scb), + GFP_ATOMIC); + if (scb_data->scbarray == NULL) + return (ENOMEM); + + /* Determine the number of hardware SCBs and initialize them */ + + scb_data->maxhscbs = ahc_probe_scbs(ahc); + if (ahc->scb_data->maxhscbs == 0) { + printk("%s: No SCB space found\n", ahc_name(ahc)); + return (ENXIO); + } + + /* + * Create our DMA tags. These tags define the kinds of device + * accessible memory allocations and memory mappings we will + * need to perform during normal operation. + * + * Unless we need to further restrict the allocation, we rely + * on the restrictions of the parent dmat, hence the common + * use of MAXADDR and MAXSIZE. + */ + + /* DMA tag for our hardware scb structures */ + if (ahc_dma_tag_create(ahc, ahc->parent_dmat, /*alignment*/1, + /*boundary*/BUS_SPACE_MAXADDR_32BIT + 1, + /*lowaddr*/BUS_SPACE_MAXADDR_32BIT, + /*highaddr*/BUS_SPACE_MAXADDR, + /*filter*/NULL, /*filterarg*/NULL, + AHC_SCB_MAX_ALLOC * sizeof(struct hardware_scb), + /*nsegments*/1, + /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, + /*flags*/0, &scb_data->hscb_dmat) != 0) { + goto error_exit; + } + + scb_data->init_level++; + + /* Allocation for our hscbs */ + if (ahc_dmamem_alloc(ahc, scb_data->hscb_dmat, + (void **)&scb_data->hscbs, + BUS_DMA_NOWAIT, &scb_data->hscb_dmamap) != 0) { + goto error_exit; + } + + scb_data->init_level++; + + /* And permanently map them */ + ahc_dmamap_load(ahc, scb_data->hscb_dmat, scb_data->hscb_dmamap, + scb_data->hscbs, + AHC_SCB_MAX_ALLOC * sizeof(struct hardware_scb), + ahc_dmamap_cb, &scb_data->hscb_busaddr, /*flags*/0); + + scb_data->init_level++; + + /* DMA tag for our sense buffers */ + if (ahc_dma_tag_create(ahc, ahc->parent_dmat, /*alignment*/1, + /*boundary*/BUS_SPACE_MAXADDR_32BIT + 1, + /*lowaddr*/BUS_SPACE_MAXADDR_32BIT, + /*highaddr*/BUS_SPACE_MAXADDR, + /*filter*/NULL, /*filterarg*/NULL, + AHC_SCB_MAX_ALLOC * sizeof(struct scsi_sense_data), + /*nsegments*/1, + /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, + /*flags*/0, &scb_data->sense_dmat) != 0) { + goto error_exit; + } + + scb_data->init_level++; + + /* Allocate them */ + if (ahc_dmamem_alloc(ahc, scb_data->sense_dmat, + (void **)&scb_data->sense, + BUS_DMA_NOWAIT, &scb_data->sense_dmamap) != 0) { + goto error_exit; + } + + scb_data->init_level++; + + /* And permanently map them */ + ahc_dmamap_load(ahc, scb_data->sense_dmat, scb_data->sense_dmamap, + scb_data->sense, + AHC_SCB_MAX_ALLOC * sizeof(struct scsi_sense_data), + ahc_dmamap_cb, &scb_data->sense_busaddr, /*flags*/0); + + scb_data->init_level++; + + /* DMA tag for our S/G structures. We allocate in page sized chunks */ + if (ahc_dma_tag_create(ahc, ahc->parent_dmat, /*alignment*/8, + /*boundary*/BUS_SPACE_MAXADDR_32BIT + 1, + /*lowaddr*/BUS_SPACE_MAXADDR_32BIT, + /*highaddr*/BUS_SPACE_MAXADDR, + /*filter*/NULL, /*filterarg*/NULL, + PAGE_SIZE, /*nsegments*/1, + /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, + /*flags*/0, &scb_data->sg_dmat) != 0) { + goto error_exit; + } + + scb_data->init_level++; + + /* Perform initial CCB allocation */ + memset(scb_data->hscbs, 0, + AHC_SCB_MAX_ALLOC * sizeof(struct hardware_scb)); + ahc_alloc_scbs(ahc); + + if (scb_data->numscbs == 0) { + printk("%s: ahc_init_scbdata - " + "Unable to allocate initial scbs\n", + ahc_name(ahc)); + goto error_exit; + } + + /* + * Reserve the next queued SCB. + */ + ahc->next_queued_scb = ahc_get_scb(ahc); + + /* + * Note that we were successful + */ + return (0); + +error_exit: + + return (ENOMEM); +} + +static void +ahc_fini_scbdata(struct ahc_softc *ahc) +{ + struct scb_data *scb_data; + + scb_data = ahc->scb_data; + if (scb_data == NULL) + return; + + switch (scb_data->init_level) { + default: + case 7: + { + struct sg_map_node *sg_map; + + while ((sg_map = SLIST_FIRST(&scb_data->sg_maps))!= NULL) { + SLIST_REMOVE_HEAD(&scb_data->sg_maps, links); + ahc_dmamap_unload(ahc, scb_data->sg_dmat, + sg_map->sg_dmamap); + ahc_dmamem_free(ahc, scb_data->sg_dmat, + sg_map->sg_vaddr, + sg_map->sg_dmamap); + kfree(sg_map); + } + ahc_dma_tag_destroy(ahc, scb_data->sg_dmat); + } + fallthrough; + case 6: + ahc_dmamap_unload(ahc, scb_data->sense_dmat, + scb_data->sense_dmamap); + fallthrough; + case 5: + ahc_dmamem_free(ahc, scb_data->sense_dmat, scb_data->sense, + scb_data->sense_dmamap); + ahc_dmamap_destroy(ahc, scb_data->sense_dmat, + scb_data->sense_dmamap); + fallthrough; + case 4: + ahc_dma_tag_destroy(ahc, scb_data->sense_dmat); + fallthrough; + case 3: + ahc_dmamap_unload(ahc, scb_data->hscb_dmat, + scb_data->hscb_dmamap); + fallthrough; + case 2: + ahc_dmamem_free(ahc, scb_data->hscb_dmat, scb_data->hscbs, + scb_data->hscb_dmamap); + ahc_dmamap_destroy(ahc, scb_data->hscb_dmat, + scb_data->hscb_dmamap); + fallthrough; + case 1: + ahc_dma_tag_destroy(ahc, scb_data->hscb_dmat); + break; + case 0: + break; + } + kfree(scb_data->scbarray); +} + +static void +ahc_alloc_scbs(struct ahc_softc *ahc) +{ + struct scb_data *scb_data; + struct scb *next_scb; + struct sg_map_node *sg_map; + dma_addr_t physaddr; + struct ahc_dma_seg *segs; + int newcount; + int i; + + scb_data = ahc->scb_data; + if (scb_data->numscbs >= AHC_SCB_MAX_ALLOC) + /* Can't allocate any more */ + return; + + next_scb = &scb_data->scbarray[scb_data->numscbs]; + + sg_map = kmalloc(sizeof(*sg_map), GFP_ATOMIC); + + if (sg_map == NULL) + return; + + /* Allocate S/G space for the next batch of SCBS */ + if (ahc_dmamem_alloc(ahc, scb_data->sg_dmat, + (void **)&sg_map->sg_vaddr, + BUS_DMA_NOWAIT, &sg_map->sg_dmamap) != 0) { + kfree(sg_map); + return; + } + + SLIST_INSERT_HEAD(&scb_data->sg_maps, sg_map, links); + + ahc_dmamap_load(ahc, scb_data->sg_dmat, sg_map->sg_dmamap, + sg_map->sg_vaddr, PAGE_SIZE, ahc_dmamap_cb, + &sg_map->sg_physaddr, /*flags*/0); + + segs = sg_map->sg_vaddr; + physaddr = sg_map->sg_physaddr; + + newcount = (PAGE_SIZE / (AHC_NSEG * sizeof(struct ahc_dma_seg))); + newcount = min(newcount, (AHC_SCB_MAX_ALLOC - scb_data->numscbs)); + for (i = 0; i < newcount; i++) { + struct scb_platform_data *pdata; + + pdata = kmalloc(sizeof(*pdata), GFP_ATOMIC); + if (pdata == NULL) + break; + next_scb->platform_data = pdata; + next_scb->sg_map = sg_map; + next_scb->sg_list = segs; + /* + * The sequencer always starts with the second entry. + * The first entry is embedded in the scb. + */ + next_scb->sg_list_phys = physaddr + sizeof(struct ahc_dma_seg); + next_scb->ahc_softc = ahc; + next_scb->flags = SCB_FREE; + next_scb->hscb = &scb_data->hscbs[scb_data->numscbs]; + next_scb->hscb->tag = ahc->scb_data->numscbs; + SLIST_INSERT_HEAD(&ahc->scb_data->free_scbs, + next_scb, links.sle); + segs += AHC_NSEG; + physaddr += (AHC_NSEG * sizeof(struct ahc_dma_seg)); + next_scb++; + ahc->scb_data->numscbs++; + } +} + +void +ahc_controller_info(struct ahc_softc *ahc, char *buf) +{ + int len; + + len = sprintf(buf, "%s: ", ahc_chip_names[ahc->chip & AHC_CHIPID_MASK]); + buf += len; + if ((ahc->features & AHC_TWIN) != 0) + len = sprintf(buf, "Twin Channel, A SCSI Id=%d, " + "B SCSI Id=%d, primary %c, ", + ahc->our_id, ahc->our_id_b, + (ahc->flags & AHC_PRIMARY_CHANNEL) + 'A'); + else { + const char *speed; + const char *type; + + speed = ""; + if ((ahc->features & AHC_ULTRA) != 0) { + speed = "Ultra "; + } else if ((ahc->features & AHC_DT) != 0) { + speed = "Ultra160 "; + } else if ((ahc->features & AHC_ULTRA2) != 0) { + speed = "Ultra2 "; + } + if ((ahc->features & AHC_WIDE) != 0) { + type = "Wide"; + } else { + type = "Single"; + } + len = sprintf(buf, "%s%s Channel %c, SCSI Id=%d, ", + speed, type, ahc->channel, ahc->our_id); + } + buf += len; + + if ((ahc->flags & AHC_PAGESCBS) != 0) + sprintf(buf, "%d/%d SCBs", + ahc->scb_data->maxhscbs, AHC_MAX_QUEUE); + else + sprintf(buf, "%d SCBs", ahc->scb_data->maxhscbs); +} + +int +ahc_chip_init(struct ahc_softc *ahc) +{ + int term; + int error; + u_int i; + u_int scsi_conf; + u_int scsiseq_template; + uint32_t physaddr; + + ahc_outb(ahc, SEQ_FLAGS, 0); + ahc_outb(ahc, SEQ_FLAGS2, 0); + + /* Set the SCSI Id, SXFRCTL0, SXFRCTL1, and SIMODE1, for both channels*/ + if (ahc->features & AHC_TWIN) { + + /* + * Setup Channel B first. + */ + ahc_outb(ahc, SBLKCTL, ahc_inb(ahc, SBLKCTL) | SELBUSB); + term = (ahc->flags & AHC_TERM_ENB_B) != 0 ? STPWEN : 0; + ahc_outb(ahc, SCSIID, ahc->our_id_b); + scsi_conf = ahc_inb(ahc, SCSICONF + 1); + ahc_outb(ahc, SXFRCTL1, (scsi_conf & (ENSPCHK|STIMESEL)) + |term|ahc->seltime_b|ENSTIMER|ACTNEGEN); + if ((ahc->features & AHC_ULTRA2) != 0) + ahc_outb(ahc, SIMODE0, ahc_inb(ahc, SIMODE0)|ENIOERR); + ahc_outb(ahc, SIMODE1, ENSELTIMO|ENSCSIRST|ENSCSIPERR); + ahc_outb(ahc, SXFRCTL0, DFON|SPIOEN); + + /* Select Channel A */ + ahc_outb(ahc, SBLKCTL, ahc_inb(ahc, SBLKCTL) & ~SELBUSB); + } + term = (ahc->flags & AHC_TERM_ENB_A) != 0 ? STPWEN : 0; + if ((ahc->features & AHC_ULTRA2) != 0) + ahc_outb(ahc, SCSIID_ULTRA2, ahc->our_id); + else + ahc_outb(ahc, SCSIID, ahc->our_id); + scsi_conf = ahc_inb(ahc, SCSICONF); + ahc_outb(ahc, SXFRCTL1, (scsi_conf & (ENSPCHK|STIMESEL)) + |term|ahc->seltime + |ENSTIMER|ACTNEGEN); + if ((ahc->features & AHC_ULTRA2) != 0) + ahc_outb(ahc, SIMODE0, ahc_inb(ahc, SIMODE0)|ENIOERR); + ahc_outb(ahc, SIMODE1, ENSELTIMO|ENSCSIRST|ENSCSIPERR); + ahc_outb(ahc, SXFRCTL0, DFON|SPIOEN); + + /* There are no untagged SCBs active yet. */ + for (i = 0; i < 16; i++) { + ahc_unbusy_tcl(ahc, BUILD_TCL(i << 4, 0)); + if ((ahc->flags & AHC_SCB_BTT) != 0) { + int lun; + + /* + * The SCB based BTT allows an entry per + * target and lun pair. + */ + for (lun = 1; lun < AHC_NUM_LUNS; lun++) + ahc_unbusy_tcl(ahc, BUILD_TCL(i << 4, lun)); + } + } + + /* All of our queues are empty */ + for (i = 0; i < 256; i++) + ahc->qoutfifo[i] = SCB_LIST_NULL; + ahc_sync_qoutfifo(ahc, BUS_DMASYNC_PREREAD); + + for (i = 0; i < 256; i++) + ahc->qinfifo[i] = SCB_LIST_NULL; + + if ((ahc->features & AHC_MULTI_TID) != 0) { + ahc_outb(ahc, TARGID, 0); + ahc_outb(ahc, TARGID + 1, 0); + } + + /* + * Tell the sequencer where it can find our arrays in memory. + */ + physaddr = ahc->scb_data->hscb_busaddr; + ahc_outb(ahc, HSCB_ADDR, physaddr & 0xFF); + ahc_outb(ahc, HSCB_ADDR + 1, (physaddr >> 8) & 0xFF); + ahc_outb(ahc, HSCB_ADDR + 2, (physaddr >> 16) & 0xFF); + ahc_outb(ahc, HSCB_ADDR + 3, (physaddr >> 24) & 0xFF); + + physaddr = ahc->shared_data_busaddr; + ahc_outb(ahc, SHARED_DATA_ADDR, physaddr & 0xFF); + ahc_outb(ahc, SHARED_DATA_ADDR + 1, (physaddr >> 8) & 0xFF); + ahc_outb(ahc, SHARED_DATA_ADDR + 2, (physaddr >> 16) & 0xFF); + ahc_outb(ahc, SHARED_DATA_ADDR + 3, (physaddr >> 24) & 0xFF); + + /* + * Initialize the group code to command length table. + * This overrides the values in TARG_SCSIRATE, so only + * setup the table after we have processed that information. + */ + ahc_outb(ahc, CMDSIZE_TABLE, 5); + ahc_outb(ahc, CMDSIZE_TABLE + 1, 9); + ahc_outb(ahc, CMDSIZE_TABLE + 2, 9); + ahc_outb(ahc, CMDSIZE_TABLE + 3, 0); + ahc_outb(ahc, CMDSIZE_TABLE + 4, 15); + ahc_outb(ahc, CMDSIZE_TABLE + 5, 11); + ahc_outb(ahc, CMDSIZE_TABLE + 6, 0); + ahc_outb(ahc, CMDSIZE_TABLE + 7, 0); + + if ((ahc->features & AHC_HS_MAILBOX) != 0) + ahc_outb(ahc, HS_MAILBOX, 0); + + /* Tell the sequencer of our initial queue positions */ + if ((ahc->features & AHC_TARGETMODE) != 0) { + ahc->tqinfifonext = 1; + ahc_outb(ahc, KERNEL_TQINPOS, ahc->tqinfifonext - 1); + ahc_outb(ahc, TQINPOS, ahc->tqinfifonext); + } + ahc->qinfifonext = 0; + ahc->qoutfifonext = 0; + if ((ahc->features & AHC_QUEUE_REGS) != 0) { + ahc_outb(ahc, QOFF_CTLSTA, SCB_QSIZE_256); + ahc_outb(ahc, HNSCB_QOFF, ahc->qinfifonext); + ahc_outb(ahc, SNSCB_QOFF, ahc->qinfifonext); + ahc_outb(ahc, SDSCB_QOFF, 0); + } else { + ahc_outb(ahc, KERNEL_QINPOS, ahc->qinfifonext); + ahc_outb(ahc, QINPOS, ahc->qinfifonext); + ahc_outb(ahc, QOUTPOS, ahc->qoutfifonext); + } + + /* We don't have any waiting selections */ + ahc_outb(ahc, WAITING_SCBH, SCB_LIST_NULL); + + /* Our disconnection list is empty too */ + ahc_outb(ahc, DISCONNECTED_SCBH, SCB_LIST_NULL); + + /* Message out buffer starts empty */ + ahc_outb(ahc, MSG_OUT, MSG_NOOP); + + /* + * Setup the allowed SCSI Sequences based on operational mode. + * If we are a target, we'll enable select in operations once + * we've had a lun enabled. + */ + scsiseq_template = ENSELO|ENAUTOATNO|ENAUTOATNP; + if ((ahc->flags & AHC_INITIATORROLE) != 0) + scsiseq_template |= ENRSELI; + ahc_outb(ahc, SCSISEQ_TEMPLATE, scsiseq_template); + + /* Initialize our list of free SCBs. */ + ahc_build_free_scb_list(ahc); + + /* + * Tell the sequencer which SCB will be the next one it receives. + */ + ahc_outb(ahc, NEXT_QUEUED_SCB, ahc->next_queued_scb->hscb->tag); + + /* + * Load the Sequencer program and Enable the adapter + * in "fast" mode. + */ + if (bootverbose) + printk("%s: Downloading Sequencer Program...", + ahc_name(ahc)); + + error = ahc_loadseq(ahc); + if (error != 0) + return (error); + + if ((ahc->features & AHC_ULTRA2) != 0) { + int wait; + + /* + * Wait for up to 500ms for our transceivers + * to settle. If the adapter does not have + * a cable attached, the transceivers may + * never settle, so don't complain if we + * fail here. + */ + for (wait = 5000; + (ahc_inb(ahc, SBLKCTL) & (ENAB40|ENAB20)) == 0 && wait; + wait--) + ahc_delay(100); + } + ahc_restart(ahc); + return (0); +} + +/* + * Start the board, ready for normal operation + */ +int +ahc_init(struct ahc_softc *ahc) +{ + int max_targ; + u_int i; + u_int scsi_conf; + u_int ultraenb; + u_int discenable; + u_int tagenable; + size_t driver_data_size; + +#ifdef AHC_DEBUG + if ((ahc_debug & AHC_DEBUG_SEQUENCER) != 0) + ahc->flags |= AHC_SEQUENCER_DEBUG; +#endif + +#ifdef AHC_PRINT_SRAM + printk("Scratch Ram:"); + for (i = 0x20; i < 0x5f; i++) { + if (((i % 8) == 0) && (i != 0)) { + printk ("\n "); + } + printk (" 0x%x", ahc_inb(ahc, i)); + } + if ((ahc->features & AHC_MORE_SRAM) != 0) { + for (i = 0x70; i < 0x7f; i++) { + if (((i % 8) == 0) && (i != 0)) { + printk ("\n "); + } + printk (" 0x%x", ahc_inb(ahc, i)); + } + } + printk ("\n"); + /* + * Reading uninitialized scratch ram may + * generate parity errors. + */ + ahc_outb(ahc, CLRINT, CLRPARERR); + ahc_outb(ahc, CLRINT, CLRBRKADRINT); +#endif + max_targ = 15; + + /* + * Assume we have a board at this stage and it has been reset. + */ + if ((ahc->flags & AHC_USEDEFAULTS) != 0) + ahc->our_id = ahc->our_id_b = 7; + + /* + * Default to allowing initiator operations. + */ + ahc->flags |= AHC_INITIATORROLE; + + /* + * Only allow target mode features if this unit has them enabled. + */ + if ((AHC_TMODE_ENABLE & (0x1 << ahc->unit)) == 0) + ahc->features &= ~AHC_TARGETMODE; + + ahc->init_level++; + + /* + * DMA tag for our command fifos and other data in system memory + * the card's sequencer must be able to access. For initiator + * roles, we need to allocate space for the qinfifo and qoutfifo. + * The qinfifo and qoutfifo are composed of 256 1 byte elements. + * When providing for the target mode role, we must additionally + * provide space for the incoming target command fifo and an extra + * byte to deal with a dma bug in some chip versions. + */ + driver_data_size = 2 * 256 * sizeof(uint8_t); + if ((ahc->features & AHC_TARGETMODE) != 0) + driver_data_size += AHC_TMODE_CMDS * sizeof(struct target_cmd) + + /*DMA WideOdd Bug Buffer*/1; + if (ahc_dma_tag_create(ahc, ahc->parent_dmat, /*alignment*/1, + /*boundary*/BUS_SPACE_MAXADDR_32BIT + 1, + /*lowaddr*/BUS_SPACE_MAXADDR_32BIT, + /*highaddr*/BUS_SPACE_MAXADDR, + /*filter*/NULL, /*filterarg*/NULL, + driver_data_size, + /*nsegments*/1, + /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, + /*flags*/0, &ahc->shared_data_dmat) != 0) { + return (ENOMEM); + } + + ahc->init_level++; + + /* Allocation of driver data */ + if (ahc_dmamem_alloc(ahc, ahc->shared_data_dmat, + (void **)&ahc->qoutfifo, + BUS_DMA_NOWAIT, &ahc->shared_data_dmamap) != 0) { + return (ENOMEM); + } + + ahc->init_level++; + + /* And permanently map it in */ + ahc_dmamap_load(ahc, ahc->shared_data_dmat, ahc->shared_data_dmamap, + ahc->qoutfifo, driver_data_size, ahc_dmamap_cb, + &ahc->shared_data_busaddr, /*flags*/0); + + if ((ahc->features & AHC_TARGETMODE) != 0) { + ahc->targetcmds = (struct target_cmd *)ahc->qoutfifo; + ahc->qoutfifo = (uint8_t *)&ahc->targetcmds[AHC_TMODE_CMDS]; + ahc->dma_bug_buf = ahc->shared_data_busaddr + + driver_data_size - 1; + /* All target command blocks start out invalid. */ + for (i = 0; i < AHC_TMODE_CMDS; i++) + ahc->targetcmds[i].cmd_valid = 0; + ahc_sync_tqinfifo(ahc, BUS_DMASYNC_PREREAD); + ahc->qoutfifo = (uint8_t *)&ahc->targetcmds[256]; + } + ahc->qinfifo = &ahc->qoutfifo[256]; + + ahc->init_level++; + + /* Allocate SCB data now that buffer_dmat is initialized */ + if (ahc->scb_data->maxhscbs == 0) + if (ahc_init_scbdata(ahc) != 0) + return (ENOMEM); + + /* + * Allocate a tstate to house information for our + * initiator presence on the bus as well as the user + * data for any target mode initiator. + */ + if (ahc_alloc_tstate(ahc, ahc->our_id, 'A') == NULL) { + printk("%s: unable to allocate ahc_tmode_tstate. " + "Failing attach\n", ahc_name(ahc)); + return (ENOMEM); + } + + if ((ahc->features & AHC_TWIN) != 0) { + if (ahc_alloc_tstate(ahc, ahc->our_id_b, 'B') == NULL) { + printk("%s: unable to allocate ahc_tmode_tstate. " + "Failing attach\n", ahc_name(ahc)); + return (ENOMEM); + } + } + + if (ahc->scb_data->maxhscbs < AHC_SCB_MAX_ALLOC) { + ahc->flags |= AHC_PAGESCBS; + } else { + ahc->flags &= ~AHC_PAGESCBS; + } + +#ifdef AHC_DEBUG + if (ahc_debug & AHC_SHOW_MISC) { + printk("%s: hardware scb %u bytes; kernel scb %u bytes; " + "ahc_dma %u bytes\n", + ahc_name(ahc), + (u_int)sizeof(struct hardware_scb), + (u_int)sizeof(struct scb), + (u_int)sizeof(struct ahc_dma_seg)); + } +#endif /* AHC_DEBUG */ + + /* + * Look at the information that board initialization or + * the board bios has left us. + */ + if (ahc->features & AHC_TWIN) { + scsi_conf = ahc_inb(ahc, SCSICONF + 1); + if ((scsi_conf & RESET_SCSI) != 0 + && (ahc->flags & AHC_INITIATORROLE) != 0) + ahc->flags |= AHC_RESET_BUS_B; + } + + scsi_conf = ahc_inb(ahc, SCSICONF); + if ((scsi_conf & RESET_SCSI) != 0 + && (ahc->flags & AHC_INITIATORROLE) != 0) + ahc->flags |= AHC_RESET_BUS_A; + + ultraenb = 0; + tagenable = ALL_TARGETS_MASK; + + /* Grab the disconnection disable table and invert it for our needs */ + if ((ahc->flags & AHC_USEDEFAULTS) != 0) { + printk("%s: Host Adapter Bios disabled. Using default SCSI " + "device parameters\n", ahc_name(ahc)); + ahc->flags |= AHC_EXTENDED_TRANS_A|AHC_EXTENDED_TRANS_B| + AHC_TERM_ENB_A|AHC_TERM_ENB_B; + discenable = ALL_TARGETS_MASK; + if ((ahc->features & AHC_ULTRA) != 0) + ultraenb = ALL_TARGETS_MASK; + } else { + discenable = ~((ahc_inb(ahc, DISC_DSB + 1) << 8) + | ahc_inb(ahc, DISC_DSB)); + if ((ahc->features & (AHC_ULTRA|AHC_ULTRA2)) != 0) + ultraenb = (ahc_inb(ahc, ULTRA_ENB + 1) << 8) + | ahc_inb(ahc, ULTRA_ENB); + } + + if ((ahc->features & (AHC_WIDE|AHC_TWIN)) == 0) + max_targ = 7; + + for (i = 0; i <= max_targ; i++) { + struct ahc_initiator_tinfo *tinfo; + struct ahc_tmode_tstate *tstate; + u_int our_id; + u_int target_id; + char channel; + + channel = 'A'; + our_id = ahc->our_id; + target_id = i; + if (i > 7 && (ahc->features & AHC_TWIN) != 0) { + channel = 'B'; + our_id = ahc->our_id_b; + target_id = i % 8; + } + tinfo = ahc_fetch_transinfo(ahc, channel, our_id, + target_id, &tstate); + /* Default to async narrow across the board */ + memset(tinfo, 0, sizeof(*tinfo)); + if (ahc->flags & AHC_USEDEFAULTS) { + if ((ahc->features & AHC_WIDE) != 0) + tinfo->user.width = MSG_EXT_WDTR_BUS_16_BIT; + + /* + * These will be truncated when we determine the + * connection type we have with the target. + */ + tinfo->user.period = ahc_syncrates->period; + tinfo->user.offset = MAX_OFFSET; + } else { + u_int scsirate; + uint16_t mask; + + /* Take the settings leftover in scratch RAM. */ + scsirate = ahc_inb(ahc, TARG_SCSIRATE + i); + mask = (0x01 << i); + if ((ahc->features & AHC_ULTRA2) != 0) { + u_int offset; + u_int maxsync; + + if ((scsirate & SOFS) == 0x0F) { + /* + * Haven't negotiated yet, + * so the format is different. + */ + scsirate = (scsirate & SXFR) >> 4 + | (ultraenb & mask) + ? 0x08 : 0x0 + | (scsirate & WIDEXFER); + offset = MAX_OFFSET_ULTRA2; + } else + offset = ahc_inb(ahc, TARG_OFFSET + i); + if ((scsirate & ~WIDEXFER) == 0 && offset != 0) + /* Set to the lowest sync rate, 5MHz */ + scsirate |= 0x1c; + maxsync = AHC_SYNCRATE_ULTRA2; + if ((ahc->features & AHC_DT) != 0) + maxsync = AHC_SYNCRATE_DT; + tinfo->user.period = + ahc_find_period(ahc, scsirate, maxsync); + if (offset == 0) + tinfo->user.period = 0; + else + tinfo->user.offset = MAX_OFFSET; + if ((scsirate & SXFR_ULTRA2) <= 8/*10MHz*/ + && (ahc->features & AHC_DT) != 0) + tinfo->user.ppr_options = + MSG_EXT_PPR_DT_REQ; + } else if ((scsirate & SOFS) != 0) { + if ((scsirate & SXFR) == 0x40 + && (ultraenb & mask) != 0) { + /* Treat 10MHz as a non-ultra speed */ + scsirate &= ~SXFR; + ultraenb &= ~mask; + } + tinfo->user.period = + ahc_find_period(ahc, scsirate, + (ultraenb & mask) + ? AHC_SYNCRATE_ULTRA + : AHC_SYNCRATE_FAST); + if (tinfo->user.period != 0) + tinfo->user.offset = MAX_OFFSET; + } + if (tinfo->user.period == 0) + tinfo->user.offset = 0; + if ((scsirate & WIDEXFER) != 0 + && (ahc->features & AHC_WIDE) != 0) + tinfo->user.width = MSG_EXT_WDTR_BUS_16_BIT; + tinfo->user.protocol_version = 4; + if ((ahc->features & AHC_DT) != 0) + tinfo->user.transport_version = 3; + else + tinfo->user.transport_version = 2; + tinfo->goal.protocol_version = 2; + tinfo->goal.transport_version = 2; + tinfo->curr.protocol_version = 2; + tinfo->curr.transport_version = 2; + } + tstate->ultraenb = 0; + } + ahc->user_discenable = discenable; + ahc->user_tagenable = tagenable; + + return (ahc->bus_chip_init(ahc)); +} + +void +ahc_intr_enable(struct ahc_softc *ahc, int enable) +{ + u_int hcntrl; + + hcntrl = ahc_inb(ahc, HCNTRL); + hcntrl &= ~INTEN; + ahc->pause &= ~INTEN; + ahc->unpause &= ~INTEN; + if (enable) { + hcntrl |= INTEN; + ahc->pause |= INTEN; + ahc->unpause |= INTEN; + } + ahc_outb(ahc, HCNTRL, hcntrl); +} + +/* + * Ensure that the card is paused in a location + * outside of all critical sections and that all + * pending work is completed prior to returning. + * This routine should only be called from outside + * an interrupt context. + */ +void +ahc_pause_and_flushwork(struct ahc_softc *ahc) +{ + int intstat; + int maxloops; + int paused; + + maxloops = 1000; + ahc->flags |= AHC_ALL_INTERRUPTS; + paused = FALSE; + do { + if (paused) { + ahc_unpause(ahc); + /* + * Give the sequencer some time to service + * any active selections. + */ + ahc_delay(500); + } + ahc_intr(ahc); + ahc_pause(ahc); + paused = TRUE; + ahc_outb(ahc, SCSISEQ, ahc_inb(ahc, SCSISEQ) & ~ENSELO); + intstat = ahc_inb(ahc, INTSTAT); + if ((intstat & INT_PEND) == 0) { + ahc_clear_critical_section(ahc); + intstat = ahc_inb(ahc, INTSTAT); + } + } while (--maxloops + && (intstat != 0xFF || (ahc->features & AHC_REMOVABLE) == 0) + && ((intstat & INT_PEND) != 0 + || (ahc_inb(ahc, SSTAT0) & (SELDO|SELINGO)) != 0)); + if (maxloops == 0) { + printk("Infinite interrupt loop, INTSTAT = %x", + ahc_inb(ahc, INTSTAT)); + } + ahc_platform_flushwork(ahc); + ahc->flags &= ~AHC_ALL_INTERRUPTS; +} + +#ifdef CONFIG_PM +int +ahc_suspend(struct ahc_softc *ahc) +{ + + ahc_pause_and_flushwork(ahc); + + if (LIST_FIRST(&ahc->pending_scbs) != NULL) { + ahc_unpause(ahc); + return (EBUSY); + } + +#ifdef AHC_TARGET_MODE + /* + * XXX What about ATIOs that have not yet been serviced? + * Perhaps we should just refuse to be suspended if we + * are acting in a target role. + */ + if (ahc->pending_device != NULL) { + ahc_unpause(ahc); + return (EBUSY); + } +#endif + ahc_shutdown(ahc); + return (0); +} + +int +ahc_resume(struct ahc_softc *ahc) +{ + + ahc_reset(ahc, /*reinit*/TRUE); + ahc_intr_enable(ahc, TRUE); + ahc_restart(ahc); + return (0); +} +#endif +/************************** Busy Target Table *********************************/ +/* + * Return the untagged transaction id for a given target/channel lun. + * Optionally, clear the entry. + */ +static u_int +ahc_index_busy_tcl(struct ahc_softc *ahc, u_int tcl) +{ + u_int scbid; + u_int target_offset; + + if ((ahc->flags & AHC_SCB_BTT) != 0) { + u_int saved_scbptr; + + saved_scbptr = ahc_inb(ahc, SCBPTR); + ahc_outb(ahc, SCBPTR, TCL_LUN(tcl)); + scbid = ahc_inb(ahc, SCB_64_BTT + TCL_TARGET_OFFSET(tcl)); + ahc_outb(ahc, SCBPTR, saved_scbptr); + } else { + target_offset = TCL_TARGET_OFFSET(tcl); + scbid = ahc_inb(ahc, BUSY_TARGETS + target_offset); + } + + return (scbid); +} + +static void +ahc_unbusy_tcl(struct ahc_softc *ahc, u_int tcl) +{ + u_int target_offset; + + if ((ahc->flags & AHC_SCB_BTT) != 0) { + u_int saved_scbptr; + + saved_scbptr = ahc_inb(ahc, SCBPTR); + ahc_outb(ahc, SCBPTR, TCL_LUN(tcl)); + ahc_outb(ahc, SCB_64_BTT+TCL_TARGET_OFFSET(tcl), SCB_LIST_NULL); + ahc_outb(ahc, SCBPTR, saved_scbptr); + } else { + target_offset = TCL_TARGET_OFFSET(tcl); + ahc_outb(ahc, BUSY_TARGETS + target_offset, SCB_LIST_NULL); + } +} + +static void +ahc_busy_tcl(struct ahc_softc *ahc, u_int tcl, u_int scbid) +{ + u_int target_offset; + + if ((ahc->flags & AHC_SCB_BTT) != 0) { + u_int saved_scbptr; + + saved_scbptr = ahc_inb(ahc, SCBPTR); + ahc_outb(ahc, SCBPTR, TCL_LUN(tcl)); + ahc_outb(ahc, SCB_64_BTT + TCL_TARGET_OFFSET(tcl), scbid); + ahc_outb(ahc, SCBPTR, saved_scbptr); + } else { + target_offset = TCL_TARGET_OFFSET(tcl); + ahc_outb(ahc, BUSY_TARGETS + target_offset, scbid); + } +} + +/************************** SCB and SCB queue management **********************/ +int +ahc_match_scb(struct ahc_softc *ahc, struct scb *scb, int target, + char channel, int lun, u_int tag, role_t role) +{ + int targ = SCB_GET_TARGET(ahc, scb); + char chan = SCB_GET_CHANNEL(ahc, scb); + int slun = SCB_GET_LUN(scb); + int match; + + match = ((chan == channel) || (channel == ALL_CHANNELS)); + if (match != 0) + match = ((targ == target) || (target == CAM_TARGET_WILDCARD)); + if (match != 0) + match = ((lun == slun) || (lun == CAM_LUN_WILDCARD)); + if (match != 0) { +#ifdef AHC_TARGET_MODE + int group; + + group = XPT_FC_GROUP(scb->io_ctx->ccb_h.func_code); + if (role == ROLE_INITIATOR) { + match = (group != XPT_FC_GROUP_TMODE) + && ((tag == scb->hscb->tag) + || (tag == SCB_LIST_NULL)); + } else if (role == ROLE_TARGET) { + match = (group == XPT_FC_GROUP_TMODE) + && ((tag == scb->io_ctx->csio.tag_id) + || (tag == SCB_LIST_NULL)); + } +#else /* !AHC_TARGET_MODE */ + match = ((tag == scb->hscb->tag) || (tag == SCB_LIST_NULL)); +#endif /* AHC_TARGET_MODE */ + } + + return match; +} + +static void +ahc_freeze_devq(struct ahc_softc *ahc, struct scb *scb) +{ + int target; + char channel; + int lun; + + target = SCB_GET_TARGET(ahc, scb); + lun = SCB_GET_LUN(scb); + channel = SCB_GET_CHANNEL(ahc, scb); + + ahc_search_qinfifo(ahc, target, channel, lun, + /*tag*/SCB_LIST_NULL, ROLE_UNKNOWN, + CAM_REQUEUE_REQ, SEARCH_COMPLETE); + + ahc_platform_freeze_devq(ahc, scb); +} + +void +ahc_qinfifo_requeue_tail(struct ahc_softc *ahc, struct scb *scb) +{ + struct scb *prev_scb; + + prev_scb = NULL; + if (ahc_qinfifo_count(ahc) != 0) { + u_int prev_tag; + uint8_t prev_pos; + + prev_pos = ahc->qinfifonext - 1; + prev_tag = ahc->qinfifo[prev_pos]; + prev_scb = ahc_lookup_scb(ahc, prev_tag); + } + ahc_qinfifo_requeue(ahc, prev_scb, scb); + if ((ahc->features & AHC_QUEUE_REGS) != 0) { + ahc_outb(ahc, HNSCB_QOFF, ahc->qinfifonext); + } else { + ahc_outb(ahc, KERNEL_QINPOS, ahc->qinfifonext); + } +} + +static void +ahc_qinfifo_requeue(struct ahc_softc *ahc, struct scb *prev_scb, + struct scb *scb) +{ + if (prev_scb == NULL) { + ahc_outb(ahc, NEXT_QUEUED_SCB, scb->hscb->tag); + } else { + prev_scb->hscb->next = scb->hscb->tag; + ahc_sync_scb(ahc, prev_scb, + BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); + } + ahc->qinfifo[ahc->qinfifonext++] = scb->hscb->tag; + scb->hscb->next = ahc->next_queued_scb->hscb->tag; + ahc_sync_scb(ahc, scb, BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); +} + +static int +ahc_qinfifo_count(struct ahc_softc *ahc) +{ + uint8_t qinpos; + uint8_t diff; + + if ((ahc->features & AHC_QUEUE_REGS) != 0) { + qinpos = ahc_inb(ahc, SNSCB_QOFF); + ahc_outb(ahc, SNSCB_QOFF, qinpos); + } else + qinpos = ahc_inb(ahc, QINPOS); + diff = ahc->qinfifonext - qinpos; + return (diff); +} + +int +ahc_search_qinfifo(struct ahc_softc *ahc, int target, char channel, + int lun, u_int tag, role_t role, uint32_t status, + ahc_search_action action) +{ + struct scb *scb; + struct scb *prev_scb; + uint8_t qinstart; + uint8_t qinpos; + uint8_t qintail; + uint8_t next; + uint8_t prev; + uint8_t curscbptr; + int found; + int have_qregs; + + qintail = ahc->qinfifonext; + have_qregs = (ahc->features & AHC_QUEUE_REGS) != 0; + if (have_qregs) { + qinstart = ahc_inb(ahc, SNSCB_QOFF); + ahc_outb(ahc, SNSCB_QOFF, qinstart); + } else + qinstart = ahc_inb(ahc, QINPOS); + qinpos = qinstart; + found = 0; + prev_scb = NULL; + + if (action == SEARCH_COMPLETE) { + /* + * Don't attempt to run any queued untagged transactions + * until we are done with the abort process. + */ + ahc_freeze_untagged_queues(ahc); + } + + /* + * Start with an empty queue. Entries that are not chosen + * for removal will be re-added to the queue as we go. + */ + ahc->qinfifonext = qinpos; + ahc_outb(ahc, NEXT_QUEUED_SCB, ahc->next_queued_scb->hscb->tag); + + while (qinpos != qintail) { + scb = ahc_lookup_scb(ahc, ahc->qinfifo[qinpos]); + if (scb == NULL) { + printk("qinpos = %d, SCB index = %d\n", + qinpos, ahc->qinfifo[qinpos]); + panic("Loop 1\n"); + } + + if (ahc_match_scb(ahc, scb, target, channel, lun, tag, role)) { + /* + * We found an scb that needs to be acted on. + */ + found++; + switch (action) { + case SEARCH_COMPLETE: + { + cam_status ostat; + cam_status cstat; + + ostat = ahc_get_transaction_status(scb); + if (ostat == CAM_REQ_INPROG) + ahc_set_transaction_status(scb, status); + cstat = ahc_get_transaction_status(scb); + if (cstat != CAM_REQ_CMP) + ahc_freeze_scb(scb); + if ((scb->flags & SCB_ACTIVE) == 0) + printk("Inactive SCB in qinfifo\n"); + ahc_done(ahc, scb); + + /* FALLTHROUGH */ + } + case SEARCH_REMOVE: + break; + case SEARCH_COUNT: + ahc_qinfifo_requeue(ahc, prev_scb, scb); + prev_scb = scb; + break; + } + } else { + ahc_qinfifo_requeue(ahc, prev_scb, scb); + prev_scb = scb; + } + qinpos++; + } + + if ((ahc->features & AHC_QUEUE_REGS) != 0) { + ahc_outb(ahc, HNSCB_QOFF, ahc->qinfifonext); + } else { + ahc_outb(ahc, KERNEL_QINPOS, ahc->qinfifonext); + } + + if (action != SEARCH_COUNT + && (found != 0) + && (qinstart != ahc->qinfifonext)) { + /* + * The sequencer may be in the process of dmaing + * down the SCB at the beginning of the queue. + * This could be problematic if either the first, + * or the second SCB is removed from the queue + * (the first SCB includes a pointer to the "next" + * SCB to dma). If we have removed any entries, swap + * the first element in the queue with the next HSCB + * so the sequencer will notice that NEXT_QUEUED_SCB + * has changed during its dma attempt and will retry + * the DMA. + */ + scb = ahc_lookup_scb(ahc, ahc->qinfifo[qinstart]); + + if (scb == NULL) { + printk("found = %d, qinstart = %d, qinfifionext = %d\n", + found, qinstart, ahc->qinfifonext); + panic("First/Second Qinfifo fixup\n"); + } + /* + * ahc_swap_with_next_hscb forces our next pointer to + * point to the reserved SCB for future commands. Save + * and restore our original next pointer to maintain + * queue integrity. + */ + next = scb->hscb->next; + ahc->scb_data->scbindex[scb->hscb->tag] = NULL; + ahc_swap_with_next_hscb(ahc, scb); + scb->hscb->next = next; + ahc->qinfifo[qinstart] = scb->hscb->tag; + + /* Tell the card about the new head of the qinfifo. */ + ahc_outb(ahc, NEXT_QUEUED_SCB, scb->hscb->tag); + + /* Fixup the tail "next" pointer. */ + qintail = ahc->qinfifonext - 1; + scb = ahc_lookup_scb(ahc, ahc->qinfifo[qintail]); + scb->hscb->next = ahc->next_queued_scb->hscb->tag; + } + + /* + * Search waiting for selection list. + */ + curscbptr = ahc_inb(ahc, SCBPTR); + next = ahc_inb(ahc, WAITING_SCBH); /* Start at head of list. */ + prev = SCB_LIST_NULL; + + while (next != SCB_LIST_NULL) { + uint8_t scb_index; + + ahc_outb(ahc, SCBPTR, next); + scb_index = ahc_inb(ahc, SCB_TAG); + if (scb_index >= ahc->scb_data->numscbs) { + printk("Waiting List inconsistency. " + "SCB index == %d, yet numscbs == %d.", + scb_index, ahc->scb_data->numscbs); + ahc_dump_card_state(ahc); + panic("for safety"); + } + scb = ahc_lookup_scb(ahc, scb_index); + if (scb == NULL) { + printk("scb_index = %d, next = %d\n", + scb_index, next); + panic("Waiting List traversal\n"); + } + if (ahc_match_scb(ahc, scb, target, channel, + lun, SCB_LIST_NULL, role)) { + /* + * We found an scb that needs to be acted on. + */ + found++; + switch (action) { + case SEARCH_COMPLETE: + { + cam_status ostat; + cam_status cstat; + + ostat = ahc_get_transaction_status(scb); + if (ostat == CAM_REQ_INPROG) + ahc_set_transaction_status(scb, + status); + cstat = ahc_get_transaction_status(scb); + if (cstat != CAM_REQ_CMP) + ahc_freeze_scb(scb); + if ((scb->flags & SCB_ACTIVE) == 0) + printk("Inactive SCB in Waiting List\n"); + ahc_done(ahc, scb); + } + fallthrough; + case SEARCH_REMOVE: + next = ahc_rem_wscb(ahc, next, prev); + break; + case SEARCH_COUNT: + prev = next; + next = ahc_inb(ahc, SCB_NEXT); + break; + } + } else { + + prev = next; + next = ahc_inb(ahc, SCB_NEXT); + } + } + ahc_outb(ahc, SCBPTR, curscbptr); + + found += ahc_search_untagged_queues(ahc, /*ahc_io_ctx_t*/NULL, target, + channel, lun, status, action); + + if (action == SEARCH_COMPLETE) + ahc_release_untagged_queues(ahc); + return (found); +} + +int +ahc_search_untagged_queues(struct ahc_softc *ahc, ahc_io_ctx_t ctx, + int target, char channel, int lun, uint32_t status, + ahc_search_action action) +{ + struct scb *scb; + int maxtarget; + int found; + int i; + + if (action == SEARCH_COMPLETE) { + /* + * Don't attempt to run any queued untagged transactions + * until we are done with the abort process. + */ + ahc_freeze_untagged_queues(ahc); + } + + found = 0; + i = 0; + if ((ahc->flags & AHC_SCB_BTT) == 0) { + + maxtarget = 16; + if (target != CAM_TARGET_WILDCARD) { + + i = target; + if (channel == 'B') + i += 8; + maxtarget = i + 1; + } + } else { + maxtarget = 0; + } + + for (; i < maxtarget; i++) { + struct scb_tailq *untagged_q; + struct scb *next_scb; + + untagged_q = &(ahc->untagged_queues[i]); + next_scb = TAILQ_FIRST(untagged_q); + while (next_scb != NULL) { + + scb = next_scb; + next_scb = TAILQ_NEXT(scb, links.tqe); + + /* + * The head of the list may be the currently + * active untagged command for a device. + * We're only searching for commands that + * have not been started. A transaction + * marked active but still in the qinfifo + * is removed by the qinfifo scanning code + * above. + */ + if ((scb->flags & SCB_ACTIVE) != 0) + continue; + + if (ahc_match_scb(ahc, scb, target, channel, lun, + SCB_LIST_NULL, ROLE_INITIATOR) == 0 + || (ctx != NULL && ctx != scb->io_ctx)) + continue; + + /* + * We found an scb that needs to be acted on. + */ + found++; + switch (action) { + case SEARCH_COMPLETE: + { + cam_status ostat; + cam_status cstat; + + ostat = ahc_get_transaction_status(scb); + if (ostat == CAM_REQ_INPROG) + ahc_set_transaction_status(scb, status); + cstat = ahc_get_transaction_status(scb); + if (cstat != CAM_REQ_CMP) + ahc_freeze_scb(scb); + if ((scb->flags & SCB_ACTIVE) == 0) + printk("Inactive SCB in untaggedQ\n"); + ahc_done(ahc, scb); + break; + } + case SEARCH_REMOVE: + scb->flags &= ~SCB_UNTAGGEDQ; + TAILQ_REMOVE(untagged_q, scb, links.tqe); + break; + case SEARCH_COUNT: + break; + } + } + } + + if (action == SEARCH_COMPLETE) + ahc_release_untagged_queues(ahc); + return (found); +} + +int +ahc_search_disc_list(struct ahc_softc *ahc, int target, char channel, + int lun, u_int tag, int stop_on_first, int remove, + int save_state) +{ + struct scb *scbp; + u_int next; + u_int prev; + u_int count; + u_int active_scb; + + count = 0; + next = ahc_inb(ahc, DISCONNECTED_SCBH); + prev = SCB_LIST_NULL; + + if (save_state) { + /* restore this when we're done */ + active_scb = ahc_inb(ahc, SCBPTR); + } else + /* Silence compiler */ + active_scb = SCB_LIST_NULL; + + while (next != SCB_LIST_NULL) { + u_int scb_index; + + ahc_outb(ahc, SCBPTR, next); + scb_index = ahc_inb(ahc, SCB_TAG); + if (scb_index >= ahc->scb_data->numscbs) { + printk("Disconnected List inconsistency. " + "SCB index == %d, yet numscbs == %d.", + scb_index, ahc->scb_data->numscbs); + ahc_dump_card_state(ahc); + panic("for safety"); + } + + if (next == prev) { + panic("Disconnected List Loop. " + "cur SCBPTR == %x, prev SCBPTR == %x.", + next, prev); + } + scbp = ahc_lookup_scb(ahc, scb_index); + if (ahc_match_scb(ahc, scbp, target, channel, lun, + tag, ROLE_INITIATOR)) { + count++; + if (remove) { + next = + ahc_rem_scb_from_disc_list(ahc, prev, next); + } else { + prev = next; + next = ahc_inb(ahc, SCB_NEXT); + } + if (stop_on_first) + break; + } else { + prev = next; + next = ahc_inb(ahc, SCB_NEXT); + } + } + if (save_state) + ahc_outb(ahc, SCBPTR, active_scb); + return (count); +} + +/* + * Remove an SCB from the on chip list of disconnected transactions. + * This is empty/unused if we are not performing SCB paging. + */ +static u_int +ahc_rem_scb_from_disc_list(struct ahc_softc *ahc, u_int prev, u_int scbptr) +{ + u_int next; + + ahc_outb(ahc, SCBPTR, scbptr); + next = ahc_inb(ahc, SCB_NEXT); + + ahc_outb(ahc, SCB_CONTROL, 0); + + ahc_add_curscb_to_free_list(ahc); + + if (prev != SCB_LIST_NULL) { + ahc_outb(ahc, SCBPTR, prev); + ahc_outb(ahc, SCB_NEXT, next); + } else + ahc_outb(ahc, DISCONNECTED_SCBH, next); + + return (next); +} + +/* + * Add the SCB as selected by SCBPTR onto the on chip list of + * free hardware SCBs. This list is empty/unused if we are not + * performing SCB paging. + */ +static void +ahc_add_curscb_to_free_list(struct ahc_softc *ahc) +{ + /* + * Invalidate the tag so that our abort + * routines don't think it's active. + */ + ahc_outb(ahc, SCB_TAG, SCB_LIST_NULL); + + if ((ahc->flags & AHC_PAGESCBS) != 0) { + ahc_outb(ahc, SCB_NEXT, ahc_inb(ahc, FREE_SCBH)); + ahc_outb(ahc, FREE_SCBH, ahc_inb(ahc, SCBPTR)); + } +} + +/* + * Manipulate the waiting for selection list and return the + * scb that follows the one that we remove. + */ +static u_int +ahc_rem_wscb(struct ahc_softc *ahc, u_int scbpos, u_int prev) +{ + u_int curscb, next; + + /* + * Select the SCB we want to abort and + * pull the next pointer out of it. + */ + curscb = ahc_inb(ahc, SCBPTR); + ahc_outb(ahc, SCBPTR, scbpos); + next = ahc_inb(ahc, SCB_NEXT); + + /* Clear the necessary fields */ + ahc_outb(ahc, SCB_CONTROL, 0); + + ahc_add_curscb_to_free_list(ahc); + + /* update the waiting list */ + if (prev == SCB_LIST_NULL) { + /* First in the list */ + ahc_outb(ahc, WAITING_SCBH, next); + + /* + * Ensure we aren't attempting to perform + * selection for this entry. + */ + ahc_outb(ahc, SCSISEQ, (ahc_inb(ahc, SCSISEQ) & ~ENSELO)); + } else { + /* + * Select the scb that pointed to us + * and update its next pointer. + */ + ahc_outb(ahc, SCBPTR, prev); + ahc_outb(ahc, SCB_NEXT, next); + } + + /* + * Point us back at the original scb position. + */ + ahc_outb(ahc, SCBPTR, curscb); + return next; +} + +/******************************** Error Handling ******************************/ +/* + * Abort all SCBs that match the given description (target/channel/lun/tag), + * setting their status to the passed in status if the status has not already + * been modified from CAM_REQ_INPROG. This routine assumes that the sequencer + * is paused before it is called. + */ +static int +ahc_abort_scbs(struct ahc_softc *ahc, int target, char channel, + int lun, u_int tag, role_t role, uint32_t status) +{ + struct scb *scbp; + struct scb *scbp_next; + u_int active_scb; + int i, j; + int maxtarget; + int minlun; + int maxlun; + + int found; + + /* + * Don't attempt to run any queued untagged transactions + * until we are done with the abort process. + */ + ahc_freeze_untagged_queues(ahc); + + /* restore this when we're done */ + active_scb = ahc_inb(ahc, SCBPTR); + + found = ahc_search_qinfifo(ahc, target, channel, lun, SCB_LIST_NULL, + role, CAM_REQUEUE_REQ, SEARCH_COMPLETE); + + /* + * Clean out the busy target table for any untagged commands. + */ + i = 0; + maxtarget = 16; + if (target != CAM_TARGET_WILDCARD) { + i = target; + if (channel == 'B') + i += 8; + maxtarget = i + 1; + } + + if (lun == CAM_LUN_WILDCARD) { + + /* + * Unless we are using an SCB based + * busy targets table, there is only + * one table entry for all luns of + * a target. + */ + minlun = 0; + maxlun = 1; + if ((ahc->flags & AHC_SCB_BTT) != 0) + maxlun = AHC_NUM_LUNS; + } else { + minlun = lun; + maxlun = lun + 1; + } + + if (role != ROLE_TARGET) { + for (;i < maxtarget; i++) { + for (j = minlun;j < maxlun; j++) { + u_int scbid; + u_int tcl; + + tcl = BUILD_TCL(i << 4, j); + scbid = ahc_index_busy_tcl(ahc, tcl); + scbp = ahc_lookup_scb(ahc, scbid); + if (scbp == NULL + || ahc_match_scb(ahc, scbp, target, channel, + lun, tag, role) == 0) + continue; + ahc_unbusy_tcl(ahc, BUILD_TCL(i << 4, j)); + } + } + + /* + * Go through the disconnected list and remove any entries we + * have queued for completion, 0'ing their control byte too. + * We save the active SCB and restore it ourselves, so there + * is no reason for this search to restore it too. + */ + ahc_search_disc_list(ahc, target, channel, lun, tag, + /*stop_on_first*/FALSE, /*remove*/TRUE, + /*save_state*/FALSE); + } + + /* + * Go through the hardware SCB array looking for commands that + * were active but not on any list. In some cases, these remnants + * might not still have mappings in the scbindex array (e.g. unexpected + * bus free with the same scb queued for an abort). Don't hold this + * against them. + */ + for (i = 0; i < ahc->scb_data->maxhscbs; i++) { + u_int scbid; + + ahc_outb(ahc, SCBPTR, i); + scbid = ahc_inb(ahc, SCB_TAG); + scbp = ahc_lookup_scb(ahc, scbid); + if ((scbp == NULL && scbid != SCB_LIST_NULL) + || (scbp != NULL + && ahc_match_scb(ahc, scbp, target, channel, lun, tag, role))) + ahc_add_curscb_to_free_list(ahc); + } + + /* + * Go through the pending CCB list and look for + * commands for this target that are still active. + * These are other tagged commands that were + * disconnected when the reset occurred. + */ + scbp_next = LIST_FIRST(&ahc->pending_scbs); + while (scbp_next != NULL) { + scbp = scbp_next; + scbp_next = LIST_NEXT(scbp, pending_links); + if (ahc_match_scb(ahc, scbp, target, channel, lun, tag, role)) { + cam_status ostat; + + ostat = ahc_get_transaction_status(scbp); + if (ostat == CAM_REQ_INPROG) + ahc_set_transaction_status(scbp, status); + if (ahc_get_transaction_status(scbp) != CAM_REQ_CMP) + ahc_freeze_scb(scbp); + if ((scbp->flags & SCB_ACTIVE) == 0) + printk("Inactive SCB on pending list\n"); + ahc_done(ahc, scbp); + found++; + } + } + ahc_outb(ahc, SCBPTR, active_scb); + ahc_platform_abort_scbs(ahc, target, channel, lun, tag, role, status); + ahc_release_untagged_queues(ahc); + return found; +} + +static void +ahc_reset_current_bus(struct ahc_softc *ahc) +{ + uint8_t scsiseq; + + ahc_outb(ahc, SIMODE1, ahc_inb(ahc, SIMODE1) & ~ENSCSIRST); + scsiseq = ahc_inb(ahc, SCSISEQ); + ahc_outb(ahc, SCSISEQ, scsiseq | SCSIRSTO); + ahc_flush_device_writes(ahc); + ahc_delay(AHC_BUSRESET_DELAY); + /* Turn off the bus reset */ + ahc_outb(ahc, SCSISEQ, scsiseq & ~SCSIRSTO); + + ahc_clear_intstat(ahc); + + /* Re-enable reset interrupts */ + ahc_outb(ahc, SIMODE1, ahc_inb(ahc, SIMODE1) | ENSCSIRST); +} + +int +ahc_reset_channel(struct ahc_softc *ahc, char channel, int initiate_reset) +{ + struct ahc_devinfo devinfo; + u_int initiator, target, max_scsiid; + u_int sblkctl; + u_int scsiseq; + u_int simode1; + int found; + int restart_needed; + char cur_channel; + + ahc->pending_device = NULL; + + ahc_compile_devinfo(&devinfo, + CAM_TARGET_WILDCARD, + CAM_TARGET_WILDCARD, + CAM_LUN_WILDCARD, + channel, ROLE_UNKNOWN); + ahc_pause(ahc); + + /* Make sure the sequencer is in a safe location. */ + ahc_clear_critical_section(ahc); + + /* + * Run our command complete fifos to ensure that we perform + * completion processing on any commands that 'completed' + * before the reset occurred. + */ + ahc_run_qoutfifo(ahc); +#ifdef AHC_TARGET_MODE + /* + * XXX - In Twin mode, the tqinfifo may have commands + * for an unaffected channel in it. However, if + * we have run out of ATIO resources to drain that + * queue, we may not get them all out here. Further, + * the blocked transactions for the reset channel + * should just be killed off, irrespecitve of whether + * we are blocked on ATIO resources. Write a routine + * to compact the tqinfifo appropriately. + */ + if ((ahc->flags & AHC_TARGETROLE) != 0) { + ahc_run_tqinfifo(ahc, /*paused*/TRUE); + } +#endif + + /* + * Reset the bus if we are initiating this reset + */ + sblkctl = ahc_inb(ahc, SBLKCTL); + cur_channel = 'A'; + if ((ahc->features & AHC_TWIN) != 0 + && ((sblkctl & SELBUSB) != 0)) + cur_channel = 'B'; + scsiseq = ahc_inb(ahc, SCSISEQ_TEMPLATE); + if (cur_channel != channel) { + /* Case 1: Command for another bus is active + * Stealthily reset the other bus without + * upsetting the current bus. + */ + ahc_outb(ahc, SBLKCTL, sblkctl ^ SELBUSB); + simode1 = ahc_inb(ahc, SIMODE1) & ~(ENBUSFREE|ENSCSIRST); +#ifdef AHC_TARGET_MODE + /* + * Bus resets clear ENSELI, so we cannot + * defer re-enabling bus reset interrupts + * if we are in target mode. + */ + if ((ahc->flags & AHC_TARGETROLE) != 0) + simode1 |= ENSCSIRST; +#endif + ahc_outb(ahc, SIMODE1, simode1); + if (initiate_reset) + ahc_reset_current_bus(ahc); + ahc_clear_intstat(ahc); + ahc_outb(ahc, SCSISEQ, scsiseq & (ENSELI|ENRSELI|ENAUTOATNP)); + ahc_outb(ahc, SBLKCTL, sblkctl); + restart_needed = FALSE; + } else { + /* Case 2: A command from this bus is active or we're idle */ + simode1 = ahc_inb(ahc, SIMODE1) & ~(ENBUSFREE|ENSCSIRST); +#ifdef AHC_TARGET_MODE + /* + * Bus resets clear ENSELI, so we cannot + * defer re-enabling bus reset interrupts + * if we are in target mode. + */ + if ((ahc->flags & AHC_TARGETROLE) != 0) + simode1 |= ENSCSIRST; +#endif + ahc_outb(ahc, SIMODE1, simode1); + if (initiate_reset) + ahc_reset_current_bus(ahc); + ahc_clear_intstat(ahc); + ahc_outb(ahc, SCSISEQ, scsiseq & (ENSELI|ENRSELI|ENAUTOATNP)); + restart_needed = TRUE; + } + + /* + * Clean up all the state information for the + * pending transactions on this bus. + */ + found = ahc_abort_scbs(ahc, CAM_TARGET_WILDCARD, channel, + CAM_LUN_WILDCARD, SCB_LIST_NULL, + ROLE_UNKNOWN, CAM_SCSI_BUS_RESET); + + max_scsiid = (ahc->features & AHC_WIDE) ? 15 : 7; + +#ifdef AHC_TARGET_MODE + /* + * Send an immediate notify ccb to all target more peripheral + * drivers affected by this action. + */ + for (target = 0; target <= max_scsiid; target++) { + struct ahc_tmode_tstate* tstate; + u_int lun; + + tstate = ahc->enabled_targets[target]; + if (tstate == NULL) + continue; + for (lun = 0; lun < AHC_NUM_LUNS; lun++) { + struct ahc_tmode_lstate* lstate; + + lstate = tstate->enabled_luns[lun]; + if (lstate == NULL) + continue; + + ahc_queue_lstate_event(ahc, lstate, CAM_TARGET_WILDCARD, + EVENT_TYPE_BUS_RESET, /*arg*/0); + ahc_send_lstate_events(ahc, lstate); + } + } +#endif + /* Notify the XPT that a bus reset occurred */ + ahc_send_async(ahc, devinfo.channel, CAM_TARGET_WILDCARD, + CAM_LUN_WILDCARD, AC_BUS_RESET); + + /* + * Revert to async/narrow transfers until we renegotiate. + */ + for (target = 0; target <= max_scsiid; target++) { + + if (ahc->enabled_targets[target] == NULL) + continue; + for (initiator = 0; initiator <= max_scsiid; initiator++) { + struct ahc_devinfo devinfo; + + ahc_compile_devinfo(&devinfo, target, initiator, + CAM_LUN_WILDCARD, + channel, ROLE_UNKNOWN); + ahc_set_width(ahc, &devinfo, MSG_EXT_WDTR_BUS_8_BIT, + AHC_TRANS_CUR, /*paused*/TRUE); + ahc_set_syncrate(ahc, &devinfo, /*syncrate*/NULL, + /*period*/0, /*offset*/0, + /*ppr_options*/0, AHC_TRANS_CUR, + /*paused*/TRUE); + } + } + + if (restart_needed) + ahc_restart(ahc); + else + ahc_unpause(ahc); + return found; +} + + +/***************************** Residual Processing ****************************/ +/* + * Calculate the residual for a just completed SCB. + */ +static void +ahc_calc_residual(struct ahc_softc *ahc, struct scb *scb) +{ + struct hardware_scb *hscb; + struct status_pkt *spkt; + uint32_t sgptr; + uint32_t resid_sgptr; + uint32_t resid; + + /* + * 5 cases. + * 1) No residual. + * SG_RESID_VALID clear in sgptr. + * 2) Transferless command + * 3) Never performed any transfers. + * sgptr has SG_FULL_RESID set. + * 4) No residual but target did not + * save data pointers after the + * last transfer, so sgptr was + * never updated. + * 5) We have a partial residual. + * Use residual_sgptr to determine + * where we are. + */ + + hscb = scb->hscb; + sgptr = ahc_le32toh(hscb->sgptr); + if ((sgptr & SG_RESID_VALID) == 0) + /* Case 1 */ + return; + sgptr &= ~SG_RESID_VALID; + + if ((sgptr & SG_LIST_NULL) != 0) + /* Case 2 */ + return; + + spkt = &hscb->shared_data.status; + resid_sgptr = ahc_le32toh(spkt->residual_sg_ptr); + if ((sgptr & SG_FULL_RESID) != 0) { + /* Case 3 */ + resid = ahc_get_transfer_length(scb); + } else if ((resid_sgptr & SG_LIST_NULL) != 0) { + /* Case 4 */ + return; + } else if ((resid_sgptr & ~SG_PTR_MASK) != 0) { + panic("Bogus resid sgptr value 0x%x\n", resid_sgptr); + } else { + struct ahc_dma_seg *sg; + + /* + * Remainder of the SG where the transfer + * stopped. + */ + resid = ahc_le32toh(spkt->residual_datacnt) & AHC_SG_LEN_MASK; + sg = ahc_sg_bus_to_virt(scb, resid_sgptr & SG_PTR_MASK); + + /* The residual sg_ptr always points to the next sg */ + sg--; + + /* + * Add up the contents of all residual + * SG segments that are after the SG where + * the transfer stopped. + */ + while ((ahc_le32toh(sg->len) & AHC_DMA_LAST_SEG) == 0) { + sg++; + resid += ahc_le32toh(sg->len) & AHC_SG_LEN_MASK; + } + } + if ((scb->flags & SCB_SENSE) == 0) + ahc_set_residual(scb, resid); + else + ahc_set_sense_residual(scb, resid); + +#ifdef AHC_DEBUG + if ((ahc_debug & AHC_SHOW_MISC) != 0) { + ahc_print_path(ahc, scb); + printk("Handled %sResidual of %d bytes\n", + (scb->flags & SCB_SENSE) ? "Sense " : "", resid); + } +#endif +} + +/******************************* Target Mode **********************************/ +#ifdef AHC_TARGET_MODE +/* + * Add a target mode event to this lun's queue + */ +static void +ahc_queue_lstate_event(struct ahc_softc *ahc, struct ahc_tmode_lstate *lstate, + u_int initiator_id, u_int event_type, u_int event_arg) +{ + struct ahc_tmode_event *event; + int pending; + + xpt_freeze_devq(lstate->path, /*count*/1); + if (lstate->event_w_idx >= lstate->event_r_idx) + pending = lstate->event_w_idx - lstate->event_r_idx; + else + pending = AHC_TMODE_EVENT_BUFFER_SIZE + 1 + - (lstate->event_r_idx - lstate->event_w_idx); + + if (event_type == EVENT_TYPE_BUS_RESET + || event_type == MSG_BUS_DEV_RESET) { + /* + * Any earlier events are irrelevant, so reset our buffer. + * This has the effect of allowing us to deal with reset + * floods (an external device holding down the reset line) + * without losing the event that is really interesting. + */ + lstate->event_r_idx = 0; + lstate->event_w_idx = 0; + xpt_release_devq(lstate->path, pending, /*runqueue*/FALSE); + } + + if (pending == AHC_TMODE_EVENT_BUFFER_SIZE) { + xpt_print_path(lstate->path); + printk("immediate event %x:%x lost\n", + lstate->event_buffer[lstate->event_r_idx].event_type, + lstate->event_buffer[lstate->event_r_idx].event_arg); + lstate->event_r_idx++; + if (lstate->event_r_idx == AHC_TMODE_EVENT_BUFFER_SIZE) + lstate->event_r_idx = 0; + xpt_release_devq(lstate->path, /*count*/1, /*runqueue*/FALSE); + } + + event = &lstate->event_buffer[lstate->event_w_idx]; + event->initiator_id = initiator_id; + event->event_type = event_type; + event->event_arg = event_arg; + lstate->event_w_idx++; + if (lstate->event_w_idx == AHC_TMODE_EVENT_BUFFER_SIZE) + lstate->event_w_idx = 0; +} + +/* + * Send any target mode events queued up waiting + * for immediate notify resources. + */ +void +ahc_send_lstate_events(struct ahc_softc *ahc, struct ahc_tmode_lstate *lstate) +{ + struct ccb_hdr *ccbh; + struct ccb_immed_notify *inot; + + while (lstate->event_r_idx != lstate->event_w_idx + && (ccbh = SLIST_FIRST(&lstate->immed_notifies)) != NULL) { + struct ahc_tmode_event *event; + + event = &lstate->event_buffer[lstate->event_r_idx]; + SLIST_REMOVE_HEAD(&lstate->immed_notifies, sim_links.sle); + inot = (struct ccb_immed_notify *)ccbh; + switch (event->event_type) { + case EVENT_TYPE_BUS_RESET: + ccbh->status = CAM_SCSI_BUS_RESET|CAM_DEV_QFRZN; + break; + default: + ccbh->status = CAM_MESSAGE_RECV|CAM_DEV_QFRZN; + inot->message_args[0] = event->event_type; + inot->message_args[1] = event->event_arg; + break; + } + inot->initiator_id = event->initiator_id; + inot->sense_len = 0; + xpt_done((union ccb *)inot); + lstate->event_r_idx++; + if (lstate->event_r_idx == AHC_TMODE_EVENT_BUFFER_SIZE) + lstate->event_r_idx = 0; + } +} +#endif + +/******************** Sequencer Program Patching/Download *********************/ + +#ifdef AHC_DUMP_SEQ +void +ahc_dumpseq(struct ahc_softc* ahc) +{ + int i; + + ahc_outb(ahc, SEQCTL, PERRORDIS|FAILDIS|FASTMODE|LOADRAM); + ahc_outb(ahc, SEQADDR0, 0); + ahc_outb(ahc, SEQADDR1, 0); + for (i = 0; i < ahc->instruction_ram_size; i++) { + uint8_t ins_bytes[4]; + + ahc_insb(ahc, SEQRAM, ins_bytes, 4); + printk("0x%08x\n", ins_bytes[0] << 24 + | ins_bytes[1] << 16 + | ins_bytes[2] << 8 + | ins_bytes[3]); + } +} +#endif + +static int +ahc_loadseq(struct ahc_softc *ahc) +{ + struct cs cs_table[NUM_CRITICAL_SECTIONS]; + u_int begin_set[NUM_CRITICAL_SECTIONS]; + u_int end_set[NUM_CRITICAL_SECTIONS]; + const struct patch *cur_patch; + u_int cs_count; + u_int cur_cs; + u_int i; + u_int skip_addr; + u_int sg_prefetch_cnt; + int downloaded; + uint8_t download_consts[7]; + + /* + * Start out with 0 critical sections + * that apply to this firmware load. + */ + cs_count = 0; + cur_cs = 0; + memset(begin_set, 0, sizeof(begin_set)); + memset(end_set, 0, sizeof(end_set)); + + /* Setup downloadable constant table */ + download_consts[QOUTFIFO_OFFSET] = 0; + if (ahc->targetcmds != NULL) + download_consts[QOUTFIFO_OFFSET] += 32; + download_consts[QINFIFO_OFFSET] = download_consts[QOUTFIFO_OFFSET] + 1; + download_consts[CACHESIZE_MASK] = ahc->pci_cachesize - 1; + download_consts[INVERTED_CACHESIZE_MASK] = ~(ahc->pci_cachesize - 1); + sg_prefetch_cnt = ahc->pci_cachesize; + if (sg_prefetch_cnt < (2 * sizeof(struct ahc_dma_seg))) + sg_prefetch_cnt = 2 * sizeof(struct ahc_dma_seg); + download_consts[SG_PREFETCH_CNT] = sg_prefetch_cnt; + download_consts[SG_PREFETCH_ALIGN_MASK] = ~(sg_prefetch_cnt - 1); + download_consts[SG_PREFETCH_ADDR_MASK] = (sg_prefetch_cnt - 1); + + cur_patch = patches; + downloaded = 0; + skip_addr = 0; + ahc_outb(ahc, SEQCTL, PERRORDIS|FAILDIS|FASTMODE|LOADRAM); + ahc_outb(ahc, SEQADDR0, 0); + ahc_outb(ahc, SEQADDR1, 0); + + for (i = 0; i < sizeof(seqprog)/4; i++) { + if (ahc_check_patch(ahc, &cur_patch, i, &skip_addr) == 0) { + /* + * Don't download this instruction as it + * is in a patch that was removed. + */ + continue; + } + + if (downloaded == ahc->instruction_ram_size) { + /* + * We're about to exceed the instruction + * storage capacity for this chip. Fail + * the load. + */ + printk("\n%s: Program too large for instruction memory " + "size of %d!\n", ahc_name(ahc), + ahc->instruction_ram_size); + return (ENOMEM); + } + + /* + * Move through the CS table until we find a CS + * that might apply to this instruction. + */ + for (; cur_cs < NUM_CRITICAL_SECTIONS; cur_cs++) { + if (critical_sections[cur_cs].end <= i) { + if (begin_set[cs_count] == TRUE + && end_set[cs_count] == FALSE) { + cs_table[cs_count].end = downloaded; + end_set[cs_count] = TRUE; + cs_count++; + } + continue; + } + if (critical_sections[cur_cs].begin <= i + && begin_set[cs_count] == FALSE) { + cs_table[cs_count].begin = downloaded; + begin_set[cs_count] = TRUE; + } + break; + } + ahc_download_instr(ahc, i, download_consts); + downloaded++; + } + + ahc->num_critical_sections = cs_count; + if (cs_count != 0) { + + cs_count *= sizeof(struct cs); + ahc->critical_sections = kmemdup(cs_table, cs_count, GFP_ATOMIC); + if (ahc->critical_sections == NULL) + panic("ahc_loadseq: Could not malloc"); + } + ahc_outb(ahc, SEQCTL, PERRORDIS|FAILDIS|FASTMODE); + + if (bootverbose) { + printk(" %d instructions downloaded\n", downloaded); + printk("%s: Features 0x%x, Bugs 0x%x, Flags 0x%x\n", + ahc_name(ahc), ahc->features, ahc->bugs, ahc->flags); + } + return (0); +} + +static int +ahc_check_patch(struct ahc_softc *ahc, const struct patch **start_patch, + u_int start_instr, u_int *skip_addr) +{ + const struct patch *cur_patch; + const struct patch *last_patch; + u_int num_patches; + + num_patches = ARRAY_SIZE(patches); + last_patch = &patches[num_patches]; + cur_patch = *start_patch; + + while (cur_patch < last_patch && start_instr == cur_patch->begin) { + + if (cur_patch->patch_func(ahc) == 0) { + + /* Start rejecting code */ + *skip_addr = start_instr + cur_patch->skip_instr; + cur_patch += cur_patch->skip_patch; + } else { + /* Accepted this patch. Advance to the next + * one and wait for our intruction pointer to + * hit this point. + */ + cur_patch++; + } + } + + *start_patch = cur_patch; + if (start_instr < *skip_addr) + /* Still skipping */ + return (0); + + return (1); +} + +static void +ahc_download_instr(struct ahc_softc *ahc, u_int instrptr, uint8_t *dconsts) +{ + union ins_formats instr; + struct ins_format1 *fmt1_ins; + struct ins_format3 *fmt3_ins; + u_int opcode; + + /* + * The firmware is always compiled into a little endian format. + */ + instr.integer = ahc_le32toh(*(uint32_t*)&seqprog[instrptr * 4]); + + fmt1_ins = &instr.format1; + fmt3_ins = NULL; + + /* Pull the opcode */ + opcode = instr.format1.opcode; + switch (opcode) { + case AIC_OP_JMP: + case AIC_OP_JC: + case AIC_OP_JNC: + case AIC_OP_CALL: + case AIC_OP_JNE: + case AIC_OP_JNZ: + case AIC_OP_JE: + case AIC_OP_JZ: + { + const struct patch *cur_patch; + int address_offset; + u_int address; + u_int skip_addr; + u_int i; + + fmt3_ins = &instr.format3; + address_offset = 0; + address = fmt3_ins->address; + cur_patch = patches; + skip_addr = 0; + + for (i = 0; i < address;) { + + ahc_check_patch(ahc, &cur_patch, i, &skip_addr); + + if (skip_addr > i) { + int end_addr; + + end_addr = min(address, skip_addr); + address_offset += end_addr - i; + i = skip_addr; + } else { + i++; + } + } + address -= address_offset; + fmt3_ins->address = address; + } + fallthrough; + case AIC_OP_OR: + case AIC_OP_AND: + case AIC_OP_XOR: + case AIC_OP_ADD: + case AIC_OP_ADC: + case AIC_OP_BMOV: + if (fmt1_ins->parity != 0) { + fmt1_ins->immediate = dconsts[fmt1_ins->immediate]; + } + fmt1_ins->parity = 0; + if ((ahc->features & AHC_CMD_CHAN) == 0 + && opcode == AIC_OP_BMOV) { + /* + * Block move was added at the same time + * as the command channel. Verify that + * this is only a move of a single element + * and convert the BMOV to a MOV + * (AND with an immediate of FF). + */ + if (fmt1_ins->immediate != 1) + panic("%s: BMOV not supported\n", + ahc_name(ahc)); + fmt1_ins->opcode = AIC_OP_AND; + fmt1_ins->immediate = 0xff; + } + fallthrough; + case AIC_OP_ROL: + if ((ahc->features & AHC_ULTRA2) != 0) { + int i, count; + + /* Calculate odd parity for the instruction */ + for (i = 0, count = 0; i < 31; i++) { + uint32_t mask; + + mask = 0x01 << i; + if ((instr.integer & mask) != 0) + count++; + } + if ((count & 0x01) == 0) + instr.format1.parity = 1; + } else { + /* Compress the instruction for older sequencers */ + if (fmt3_ins != NULL) { + instr.integer = + fmt3_ins->immediate + | (fmt3_ins->source << 8) + | (fmt3_ins->address << 16) + | (fmt3_ins->opcode << 25); + } else { + instr.integer = + fmt1_ins->immediate + | (fmt1_ins->source << 8) + | (fmt1_ins->destination << 16) + | (fmt1_ins->ret << 24) + | (fmt1_ins->opcode << 25); + } + } + /* The sequencer is a little endian cpu */ + instr.integer = ahc_htole32(instr.integer); + ahc_outsb(ahc, SEQRAM, instr.bytes, 4); + break; + default: + panic("Unknown opcode encountered in seq program"); + break; + } +} + +int +ahc_print_register(const ahc_reg_parse_entry_t *table, u_int num_entries, + const char *name, u_int address, u_int value, + u_int *cur_column, u_int wrap_point) +{ + int printed; + u_int printed_mask; + + if (cur_column != NULL && *cur_column >= wrap_point) { + printk("\n"); + *cur_column = 0; + } + printed = printk("%s[0x%x]", name, value); + if (table == NULL) { + printed += printk(" "); + *cur_column += printed; + return (printed); + } + printed_mask = 0; + while (printed_mask != 0xFF) { + int entry; + + for (entry = 0; entry < num_entries; entry++) { + if (((value & table[entry].mask) + != table[entry].value) + || ((printed_mask & table[entry].mask) + == table[entry].mask)) + continue; + + printed += printk("%s%s", + printed_mask == 0 ? ":(" : "|", + table[entry].name); + printed_mask |= table[entry].mask; + + break; + } + if (entry >= num_entries) + break; + } + if (printed_mask != 0) + printed += printk(") "); + else + printed += printk(" "); + if (cur_column != NULL) + *cur_column += printed; + return (printed); +} + +void +ahc_dump_card_state(struct ahc_softc *ahc) +{ + struct scb *scb; + struct scb_tailq *untagged_q; + u_int cur_col; + int paused; + int target; + int maxtarget; + int i; + uint8_t last_phase; + uint8_t qinpos; + uint8_t qintail; + uint8_t qoutpos; + uint8_t scb_index; + uint8_t saved_scbptr; + + if (ahc_is_paused(ahc)) { + paused = 1; + } else { + paused = 0; + ahc_pause(ahc); + } + + saved_scbptr = ahc_inb(ahc, SCBPTR); + last_phase = ahc_inb(ahc, LASTPHASE); + printk(">>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<\n" + "%s: Dumping Card State %s, at SEQADDR 0x%x\n", + ahc_name(ahc), ahc_lookup_phase_entry(last_phase)->phasemsg, + ahc_inb(ahc, SEQADDR0) | (ahc_inb(ahc, SEQADDR1) << 8)); + if (paused) + printk("Card was paused\n"); + printk("ACCUM = 0x%x, SINDEX = 0x%x, DINDEX = 0x%x, ARG_2 = 0x%x\n", + ahc_inb(ahc, ACCUM), ahc_inb(ahc, SINDEX), ahc_inb(ahc, DINDEX), + ahc_inb(ahc, ARG_2)); + printk("HCNT = 0x%x SCBPTR = 0x%x\n", ahc_inb(ahc, HCNT), + ahc_inb(ahc, SCBPTR)); + cur_col = 0; + if ((ahc->features & AHC_DT) != 0) + ahc_scsiphase_print(ahc_inb(ahc, SCSIPHASE), &cur_col, 50); + ahc_scsisigi_print(ahc_inb(ahc, SCSISIGI), &cur_col, 50); + ahc_error_print(ahc_inb(ahc, ERROR), &cur_col, 50); + ahc_scsibusl_print(ahc_inb(ahc, SCSIBUSL), &cur_col, 50); + ahc_lastphase_print(ahc_inb(ahc, LASTPHASE), &cur_col, 50); + ahc_scsiseq_print(ahc_inb(ahc, SCSISEQ), &cur_col, 50); + ahc_sblkctl_print(ahc_inb(ahc, SBLKCTL), &cur_col, 50); + ahc_scsirate_print(ahc_inb(ahc, SCSIRATE), &cur_col, 50); + ahc_seqctl_print(ahc_inb(ahc, SEQCTL), &cur_col, 50); + ahc_seq_flags_print(ahc_inb(ahc, SEQ_FLAGS), &cur_col, 50); + ahc_sstat0_print(ahc_inb(ahc, SSTAT0), &cur_col, 50); + ahc_sstat1_print(ahc_inb(ahc, SSTAT1), &cur_col, 50); + ahc_sstat2_print(ahc_inb(ahc, SSTAT2), &cur_col, 50); + ahc_sstat3_print(ahc_inb(ahc, SSTAT3), &cur_col, 50); + ahc_simode0_print(ahc_inb(ahc, SIMODE0), &cur_col, 50); + ahc_simode1_print(ahc_inb(ahc, SIMODE1), &cur_col, 50); + ahc_sxfrctl0_print(ahc_inb(ahc, SXFRCTL0), &cur_col, 50); + ahc_dfcntrl_print(ahc_inb(ahc, DFCNTRL), &cur_col, 50); + ahc_dfstatus_print(ahc_inb(ahc, DFSTATUS), &cur_col, 50); + if (cur_col != 0) + printk("\n"); + printk("STACK:"); + for (i = 0; i < STACK_SIZE; i++) + printk(" 0x%x", ahc_inb(ahc, STACK)|(ahc_inb(ahc, STACK) << 8)); + printk("\nSCB count = %d\n", ahc->scb_data->numscbs); + printk("Kernel NEXTQSCB = %d\n", ahc->next_queued_scb->hscb->tag); + printk("Card NEXTQSCB = %d\n", ahc_inb(ahc, NEXT_QUEUED_SCB)); + /* QINFIFO */ + printk("QINFIFO entries: "); + if ((ahc->features & AHC_QUEUE_REGS) != 0) { + qinpos = ahc_inb(ahc, SNSCB_QOFF); + ahc_outb(ahc, SNSCB_QOFF, qinpos); + } else + qinpos = ahc_inb(ahc, QINPOS); + qintail = ahc->qinfifonext; + while (qinpos != qintail) { + printk("%d ", ahc->qinfifo[qinpos]); + qinpos++; + } + printk("\n"); + + printk("Waiting Queue entries: "); + scb_index = ahc_inb(ahc, WAITING_SCBH); + i = 0; + while (scb_index != SCB_LIST_NULL && i++ < 256) { + ahc_outb(ahc, SCBPTR, scb_index); + printk("%d:%d ", scb_index, ahc_inb(ahc, SCB_TAG)); + scb_index = ahc_inb(ahc, SCB_NEXT); + } + printk("\n"); + + printk("Disconnected Queue entries: "); + scb_index = ahc_inb(ahc, DISCONNECTED_SCBH); + i = 0; + while (scb_index != SCB_LIST_NULL && i++ < 256) { + ahc_outb(ahc, SCBPTR, scb_index); + printk("%d:%d ", scb_index, ahc_inb(ahc, SCB_TAG)); + scb_index = ahc_inb(ahc, SCB_NEXT); + } + printk("\n"); + + ahc_sync_qoutfifo(ahc, BUS_DMASYNC_POSTREAD); + printk("QOUTFIFO entries: "); + qoutpos = ahc->qoutfifonext; + i = 0; + while (ahc->qoutfifo[qoutpos] != SCB_LIST_NULL && i++ < 256) { + printk("%d ", ahc->qoutfifo[qoutpos]); + qoutpos++; + } + printk("\n"); + + printk("Sequencer Free SCB List: "); + scb_index = ahc_inb(ahc, FREE_SCBH); + i = 0; + while (scb_index != SCB_LIST_NULL && i++ < 256) { + ahc_outb(ahc, SCBPTR, scb_index); + printk("%d ", scb_index); + scb_index = ahc_inb(ahc, SCB_NEXT); + } + printk("\n"); + + printk("Sequencer SCB Info: "); + for (i = 0; i < ahc->scb_data->maxhscbs; i++) { + ahc_outb(ahc, SCBPTR, i); + cur_col = printk("\n%3d ", i); + + ahc_scb_control_print(ahc_inb(ahc, SCB_CONTROL), &cur_col, 60); + ahc_scb_scsiid_print(ahc_inb(ahc, SCB_SCSIID), &cur_col, 60); + ahc_scb_lun_print(ahc_inb(ahc, SCB_LUN), &cur_col, 60); + ahc_scb_tag_print(ahc_inb(ahc, SCB_TAG), &cur_col, 60); + } + printk("\n"); + + printk("Pending list: "); + i = 0; + LIST_FOREACH(scb, &ahc->pending_scbs, pending_links) { + if (i++ > 256) + break; + cur_col = printk("\n%3d ", scb->hscb->tag); + ahc_scb_control_print(scb->hscb->control, &cur_col, 60); + ahc_scb_scsiid_print(scb->hscb->scsiid, &cur_col, 60); + ahc_scb_lun_print(scb->hscb->lun, &cur_col, 60); + if ((ahc->flags & AHC_PAGESCBS) == 0) { + ahc_outb(ahc, SCBPTR, scb->hscb->tag); + printk("("); + ahc_scb_control_print(ahc_inb(ahc, SCB_CONTROL), + &cur_col, 60); + ahc_scb_tag_print(ahc_inb(ahc, SCB_TAG), &cur_col, 60); + printk(")"); + } + } + printk("\n"); + + printk("Kernel Free SCB list: "); + i = 0; + SLIST_FOREACH(scb, &ahc->scb_data->free_scbs, links.sle) { + if (i++ > 256) + break; + printk("%d ", scb->hscb->tag); + } + printk("\n"); + + maxtarget = (ahc->features & (AHC_WIDE|AHC_TWIN)) ? 15 : 7; + for (target = 0; target <= maxtarget; target++) { + untagged_q = &ahc->untagged_queues[target]; + if (TAILQ_FIRST(untagged_q) == NULL) + continue; + printk("Untagged Q(%d): ", target); + i = 0; + TAILQ_FOREACH(scb, untagged_q, links.tqe) { + if (i++ > 256) + break; + printk("%d ", scb->hscb->tag); + } + printk("\n"); + } + + printk("\n<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>\n"); + ahc_outb(ahc, SCBPTR, saved_scbptr); + if (paused == 0) + ahc_unpause(ahc); +} + +/************************* Target Mode ****************************************/ +#ifdef AHC_TARGET_MODE +cam_status +ahc_find_tmode_devs(struct ahc_softc *ahc, struct cam_sim *sim, union ccb *ccb, + struct ahc_tmode_tstate **tstate, + struct ahc_tmode_lstate **lstate, + int notfound_failure) +{ + + if ((ahc->features & AHC_TARGETMODE) == 0) + return (CAM_REQ_INVALID); + + /* + * Handle the 'black hole' device that sucks up + * requests to unattached luns on enabled targets. + */ + if (ccb->ccb_h.target_id == CAM_TARGET_WILDCARD + && ccb->ccb_h.target_lun == CAM_LUN_WILDCARD) { + *tstate = NULL; + *lstate = ahc->black_hole; + } else { + u_int max_id; + + max_id = (ahc->features & AHC_WIDE) ? 16 : 8; + if (ccb->ccb_h.target_id >= max_id) + return (CAM_TID_INVALID); + + if (ccb->ccb_h.target_lun >= AHC_NUM_LUNS) + return (CAM_LUN_INVALID); + + *tstate = ahc->enabled_targets[ccb->ccb_h.target_id]; + *lstate = NULL; + if (*tstate != NULL) + *lstate = + (*tstate)->enabled_luns[ccb->ccb_h.target_lun]; + } + + if (notfound_failure != 0 && *lstate == NULL) + return (CAM_PATH_INVALID); + + return (CAM_REQ_CMP); +} + +void +ahc_handle_en_lun(struct ahc_softc *ahc, struct cam_sim *sim, union ccb *ccb) +{ + struct ahc_tmode_tstate *tstate; + struct ahc_tmode_lstate *lstate; + struct ccb_en_lun *cel; + cam_status status; + u_long s; + u_int target; + u_int lun; + u_int target_mask; + u_int our_id; + int error; + char channel; + + status = ahc_find_tmode_devs(ahc, sim, ccb, &tstate, &lstate, + /*notfound_failure*/FALSE); + + if (status != CAM_REQ_CMP) { + ccb->ccb_h.status = status; + return; + } + + if (cam_sim_bus(sim) == 0) + our_id = ahc->our_id; + else + our_id = ahc->our_id_b; + + if (ccb->ccb_h.target_id != our_id) { + /* + * our_id represents our initiator ID, or + * the ID of the first target to have an + * enabled lun in target mode. There are + * two cases that may preclude enabling a + * target id other than our_id. + * + * o our_id is for an active initiator role. + * Since the hardware does not support + * reselections to the initiator role at + * anything other than our_id, and our_id + * is used by the hardware to indicate the + * ID to use for both select-out and + * reselect-out operations, the only target + * ID we can support in this mode is our_id. + * + * o The MULTARGID feature is not available and + * a previous target mode ID has been enabled. + */ + if ((ahc->features & AHC_MULTIROLE) != 0) { + + if ((ahc->features & AHC_MULTI_TID) != 0 + && (ahc->flags & AHC_INITIATORROLE) != 0) { + /* + * Only allow additional targets if + * the initiator role is disabled. + * The hardware cannot handle a re-select-in + * on the initiator id during a re-select-out + * on a different target id. + */ + status = CAM_TID_INVALID; + } else if ((ahc->flags & AHC_INITIATORROLE) != 0 + || ahc->enabled_luns > 0) { + /* + * Only allow our target id to change + * if the initiator role is not configured + * and there are no enabled luns which + * are attached to the currently registered + * scsi id. + */ + status = CAM_TID_INVALID; + } + } else if ((ahc->features & AHC_MULTI_TID) == 0 + && ahc->enabled_luns > 0) { + + status = CAM_TID_INVALID; + } + } + + if (status != CAM_REQ_CMP) { + ccb->ccb_h.status = status; + return; + } + + /* + * We now have an id that is valid. + * If we aren't in target mode, switch modes. + */ + if ((ahc->flags & AHC_TARGETROLE) == 0 + && ccb->ccb_h.target_id != CAM_TARGET_WILDCARD) { + u_long s; + ahc_flag saved_flags; + + printk("Configuring Target Mode\n"); + ahc_lock(ahc, &s); + if (LIST_FIRST(&ahc->pending_scbs) != NULL) { + ccb->ccb_h.status = CAM_BUSY; + ahc_unlock(ahc, &s); + return; + } + saved_flags = ahc->flags; + ahc->flags |= AHC_TARGETROLE; + if ((ahc->features & AHC_MULTIROLE) == 0) + ahc->flags &= ~AHC_INITIATORROLE; + ahc_pause(ahc); + error = ahc_loadseq(ahc); + if (error != 0) { + /* + * Restore original configuration and notify + * the caller that we cannot support target mode. + * Since the adapter started out in this + * configuration, the firmware load will succeed, + * so there is no point in checking ahc_loadseq's + * return value. + */ + ahc->flags = saved_flags; + (void)ahc_loadseq(ahc); + ahc_restart(ahc); + ahc_unlock(ahc, &s); + ccb->ccb_h.status = CAM_FUNC_NOTAVAIL; + return; + } + ahc_restart(ahc); + ahc_unlock(ahc, &s); + } + cel = &ccb->cel; + target = ccb->ccb_h.target_id; + lun = ccb->ccb_h.target_lun; + channel = SIM_CHANNEL(ahc, sim); + target_mask = 0x01 << target; + if (channel == 'B') + target_mask <<= 8; + + if (cel->enable != 0) { + u_int scsiseq; + + /* Are we already enabled?? */ + if (lstate != NULL) { + xpt_print_path(ccb->ccb_h.path); + printk("Lun already enabled\n"); + ccb->ccb_h.status = CAM_LUN_ALRDY_ENA; + return; + } + + if (cel->grp6_len != 0 + || cel->grp7_len != 0) { + /* + * Don't (yet?) support vendor + * specific commands. + */ + ccb->ccb_h.status = CAM_REQ_INVALID; + printk("Non-zero Group Codes\n"); + return; + } + + /* + * Seems to be okay. + * Setup our data structures. + */ + if (target != CAM_TARGET_WILDCARD && tstate == NULL) { + tstate = ahc_alloc_tstate(ahc, target, channel); + if (tstate == NULL) { + xpt_print_path(ccb->ccb_h.path); + printk("Couldn't allocate tstate\n"); + ccb->ccb_h.status = CAM_RESRC_UNAVAIL; + return; + } + } + lstate = kzalloc(sizeof(*lstate), GFP_ATOMIC); + if (lstate == NULL) { + xpt_print_path(ccb->ccb_h.path); + printk("Couldn't allocate lstate\n"); + ccb->ccb_h.status = CAM_RESRC_UNAVAIL; + return; + } + status = xpt_create_path(&lstate->path, /*periph*/NULL, + xpt_path_path_id(ccb->ccb_h.path), + xpt_path_target_id(ccb->ccb_h.path), + xpt_path_lun_id(ccb->ccb_h.path)); + if (status != CAM_REQ_CMP) { + kfree(lstate); + xpt_print_path(ccb->ccb_h.path); + printk("Couldn't allocate path\n"); + ccb->ccb_h.status = CAM_RESRC_UNAVAIL; + return; + } + SLIST_INIT(&lstate->accept_tios); + SLIST_INIT(&lstate->immed_notifies); + ahc_lock(ahc, &s); + ahc_pause(ahc); + if (target != CAM_TARGET_WILDCARD) { + tstate->enabled_luns[lun] = lstate; + ahc->enabled_luns++; + + if ((ahc->features & AHC_MULTI_TID) != 0) { + u_int targid_mask; + + targid_mask = ahc_inb(ahc, TARGID) + | (ahc_inb(ahc, TARGID + 1) << 8); + + targid_mask |= target_mask; + ahc_outb(ahc, TARGID, targid_mask); + ahc_outb(ahc, TARGID+1, (targid_mask >> 8)); + + ahc_update_scsiid(ahc, targid_mask); + } else { + u_int our_id; + char channel; + + channel = SIM_CHANNEL(ahc, sim); + our_id = SIM_SCSI_ID(ahc, sim); + + /* + * This can only happen if selections + * are not enabled + */ + if (target != our_id) { + u_int sblkctl; + char cur_channel; + int swap; + + sblkctl = ahc_inb(ahc, SBLKCTL); + cur_channel = (sblkctl & SELBUSB) + ? 'B' : 'A'; + if ((ahc->features & AHC_TWIN) == 0) + cur_channel = 'A'; + swap = cur_channel != channel; + if (channel == 'A') + ahc->our_id = target; + else + ahc->our_id_b = target; + + if (swap) + ahc_outb(ahc, SBLKCTL, + sblkctl ^ SELBUSB); + + ahc_outb(ahc, SCSIID, target); + + if (swap) + ahc_outb(ahc, SBLKCTL, sblkctl); + } + } + } else + ahc->black_hole = lstate; + /* Allow select-in operations */ + if (ahc->black_hole != NULL && ahc->enabled_luns > 0) { + scsiseq = ahc_inb(ahc, SCSISEQ_TEMPLATE); + scsiseq |= ENSELI; + ahc_outb(ahc, SCSISEQ_TEMPLATE, scsiseq); + scsiseq = ahc_inb(ahc, SCSISEQ); + scsiseq |= ENSELI; + ahc_outb(ahc, SCSISEQ, scsiseq); + } + ahc_unpause(ahc); + ahc_unlock(ahc, &s); + ccb->ccb_h.status = CAM_REQ_CMP; + xpt_print_path(ccb->ccb_h.path); + printk("Lun now enabled for target mode\n"); + } else { + struct scb *scb; + int i, empty; + + if (lstate == NULL) { + ccb->ccb_h.status = CAM_LUN_INVALID; + return; + } + + ahc_lock(ahc, &s); + + ccb->ccb_h.status = CAM_REQ_CMP; + LIST_FOREACH(scb, &ahc->pending_scbs, pending_links) { + struct ccb_hdr *ccbh; + + ccbh = &scb->io_ctx->ccb_h; + if (ccbh->func_code == XPT_CONT_TARGET_IO + && !xpt_path_comp(ccbh->path, ccb->ccb_h.path)){ + printk("CTIO pending\n"); + ccb->ccb_h.status = CAM_REQ_INVALID; + ahc_unlock(ahc, &s); + return; + } + } + + if (SLIST_FIRST(&lstate->accept_tios) != NULL) { + printk("ATIOs pending\n"); + ccb->ccb_h.status = CAM_REQ_INVALID; + } + + if (SLIST_FIRST(&lstate->immed_notifies) != NULL) { + printk("INOTs pending\n"); + ccb->ccb_h.status = CAM_REQ_INVALID; + } + + if (ccb->ccb_h.status != CAM_REQ_CMP) { + ahc_unlock(ahc, &s); + return; + } + + xpt_print_path(ccb->ccb_h.path); + printk("Target mode disabled\n"); + xpt_free_path(lstate->path); + kfree(lstate); + + ahc_pause(ahc); + /* Can we clean up the target too? */ + if (target != CAM_TARGET_WILDCARD) { + tstate->enabled_luns[lun] = NULL; + ahc->enabled_luns--; + for (empty = 1, i = 0; i < 8; i++) + if (tstate->enabled_luns[i] != NULL) { + empty = 0; + break; + } + + if (empty) { + ahc_free_tstate(ahc, target, channel, + /*force*/FALSE); + if (ahc->features & AHC_MULTI_TID) { + u_int targid_mask; + + targid_mask = ahc_inb(ahc, TARGID) + | (ahc_inb(ahc, TARGID + 1) + << 8); + + targid_mask &= ~target_mask; + ahc_outb(ahc, TARGID, targid_mask); + ahc_outb(ahc, TARGID+1, + (targid_mask >> 8)); + ahc_update_scsiid(ahc, targid_mask); + } + } + } else { + + ahc->black_hole = NULL; + + /* + * We can't allow selections without + * our black hole device. + */ + empty = TRUE; + } + if (ahc->enabled_luns == 0) { + /* Disallow select-in */ + u_int scsiseq; + + scsiseq = ahc_inb(ahc, SCSISEQ_TEMPLATE); + scsiseq &= ~ENSELI; + ahc_outb(ahc, SCSISEQ_TEMPLATE, scsiseq); + scsiseq = ahc_inb(ahc, SCSISEQ); + scsiseq &= ~ENSELI; + ahc_outb(ahc, SCSISEQ, scsiseq); + + if ((ahc->features & AHC_MULTIROLE) == 0) { + printk("Configuring Initiator Mode\n"); + ahc->flags &= ~AHC_TARGETROLE; + ahc->flags |= AHC_INITIATORROLE; + /* + * Returning to a configuration that + * fit previously will always succeed. + */ + (void)ahc_loadseq(ahc); + ahc_restart(ahc); + /* + * Unpaused. The extra unpause + * that follows is harmless. + */ + } + } + ahc_unpause(ahc); + ahc_unlock(ahc, &s); + } +} + +static void +ahc_update_scsiid(struct ahc_softc *ahc, u_int targid_mask) +{ + u_int scsiid_mask; + u_int scsiid; + + if ((ahc->features & AHC_MULTI_TID) == 0) + panic("ahc_update_scsiid called on non-multitid unit\n"); + + /* + * Since we will rely on the TARGID mask + * for selection enables, ensure that OID + * in SCSIID is not set to some other ID + * that we don't want to allow selections on. + */ + if ((ahc->features & AHC_ULTRA2) != 0) + scsiid = ahc_inb(ahc, SCSIID_ULTRA2); + else + scsiid = ahc_inb(ahc, SCSIID); + scsiid_mask = 0x1 << (scsiid & OID); + if ((targid_mask & scsiid_mask) == 0) { + u_int our_id; + + /* ffs counts from 1 */ + our_id = ffs(targid_mask); + if (our_id == 0) + our_id = ahc->our_id; + else + our_id--; + scsiid &= TID; + scsiid |= our_id; + } + if ((ahc->features & AHC_ULTRA2) != 0) + ahc_outb(ahc, SCSIID_ULTRA2, scsiid); + else + ahc_outb(ahc, SCSIID, scsiid); +} + +static void +ahc_run_tqinfifo(struct ahc_softc *ahc, int paused) +{ + struct target_cmd *cmd; + + /* + * If the card supports auto-access pause, + * we can access the card directly regardless + * of whether it is paused or not. + */ + if ((ahc->features & AHC_AUTOPAUSE) != 0) + paused = TRUE; + + ahc_sync_tqinfifo(ahc, BUS_DMASYNC_POSTREAD); + while ((cmd = &ahc->targetcmds[ahc->tqinfifonext])->cmd_valid != 0) { + + /* + * Only advance through the queue if we + * have the resources to process the command. + */ + if (ahc_handle_target_cmd(ahc, cmd) != 0) + break; + + cmd->cmd_valid = 0; + ahc_dmamap_sync(ahc, ahc->shared_data_dmat, + ahc->shared_data_dmamap, + ahc_targetcmd_offset(ahc, ahc->tqinfifonext), + sizeof(struct target_cmd), + BUS_DMASYNC_PREREAD); + ahc->tqinfifonext++; + + /* + * Lazily update our position in the target mode incoming + * command queue as seen by the sequencer. + */ + if ((ahc->tqinfifonext & (HOST_TQINPOS - 1)) == 1) { + if ((ahc->features & AHC_HS_MAILBOX) != 0) { + u_int hs_mailbox; + + hs_mailbox = ahc_inb(ahc, HS_MAILBOX); + hs_mailbox &= ~HOST_TQINPOS; + hs_mailbox |= ahc->tqinfifonext & HOST_TQINPOS; + ahc_outb(ahc, HS_MAILBOX, hs_mailbox); + } else { + if (!paused) + ahc_pause(ahc); + ahc_outb(ahc, KERNEL_TQINPOS, + ahc->tqinfifonext & HOST_TQINPOS); + if (!paused) + ahc_unpause(ahc); + } + } + } +} + +static int +ahc_handle_target_cmd(struct ahc_softc *ahc, struct target_cmd *cmd) +{ + struct ahc_tmode_tstate *tstate; + struct ahc_tmode_lstate *lstate; + struct ccb_accept_tio *atio; + uint8_t *byte; + int initiator; + int target; + int lun; + + initiator = SCSIID_TARGET(ahc, cmd->scsiid); + target = SCSIID_OUR_ID(cmd->scsiid); + lun = (cmd->identify & MSG_IDENTIFY_LUNMASK); + + byte = cmd->bytes; + tstate = ahc->enabled_targets[target]; + lstate = NULL; + if (tstate != NULL) + lstate = tstate->enabled_luns[lun]; + + /* + * Commands for disabled luns go to the black hole driver. + */ + if (lstate == NULL) + lstate = ahc->black_hole; + + atio = (struct ccb_accept_tio*)SLIST_FIRST(&lstate->accept_tios); + if (atio == NULL) { + ahc->flags |= AHC_TQINFIFO_BLOCKED; + /* + * Wait for more ATIOs from the peripheral driver for this lun. + */ + if (bootverbose) + printk("%s: ATIOs exhausted\n", ahc_name(ahc)); + return (1); + } else + ahc->flags &= ~AHC_TQINFIFO_BLOCKED; +#if 0 + printk("Incoming command from %d for %d:%d%s\n", + initiator, target, lun, + lstate == ahc->black_hole ? "(Black Holed)" : ""); +#endif + SLIST_REMOVE_HEAD(&lstate->accept_tios, sim_links.sle); + + if (lstate == ahc->black_hole) { + /* Fill in the wildcards */ + atio->ccb_h.target_id = target; + atio->ccb_h.target_lun = lun; + } + + /* + * Package it up and send it off to + * whomever has this lun enabled. + */ + atio->sense_len = 0; + atio->init_id = initiator; + if (byte[0] != 0xFF) { + /* Tag was included */ + atio->tag_action = *byte++; + atio->tag_id = *byte++; + atio->ccb_h.flags = CAM_TAG_ACTION_VALID; + } else { + atio->ccb_h.flags = 0; + } + byte++; + + /* Okay. Now determine the cdb size based on the command code */ + switch (*byte >> CMD_GROUP_CODE_SHIFT) { + case 0: + atio->cdb_len = 6; + break; + case 1: + case 2: + atio->cdb_len = 10; + break; + case 4: + atio->cdb_len = 16; + break; + case 5: + atio->cdb_len = 12; + break; + case 3: + default: + /* Only copy the opcode. */ + atio->cdb_len = 1; + printk("Reserved or VU command code type encountered\n"); + break; + } + + memcpy(atio->cdb_io.cdb_bytes, byte, atio->cdb_len); + + atio->ccb_h.status |= CAM_CDB_RECVD; + + if ((cmd->identify & MSG_IDENTIFY_DISCFLAG) == 0) { + /* + * We weren't allowed to disconnect. + * We're hanging on the bus until a + * continue target I/O comes in response + * to this accept tio. + */ +#if 0 + printk("Received Immediate Command %d:%d:%d - %p\n", + initiator, target, lun, ahc->pending_device); +#endif + ahc->pending_device = lstate; + ahc_freeze_ccb((union ccb *)atio); + atio->ccb_h.flags |= CAM_DIS_DISCONNECT; + } + xpt_done((union ccb*)atio); + return (0); +} + +#endif diff --git a/drivers/scsi/aic7xxx/aic7xxx_inline.h b/drivers/scsi/aic7xxx/aic7xxx_inline.h new file mode 100644 index 000000000..0b57b783e --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx_inline.h @@ -0,0 +1,97 @@ +/* + * Inline routines shareable across OS platforms. + * + * Copyright (c) 1994-2001 Justin T. Gibbs. + * Copyright (c) 2000-2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aic7xxx_inline.h#43 $ + * + * $FreeBSD$ + */ + +#ifndef _AIC7XXX_INLINE_H_ +#define _AIC7XXX_INLINE_H_ + +/************************* Sequencer Execution Control ************************/ +int ahc_is_paused(struct ahc_softc *ahc); +void ahc_pause(struct ahc_softc *ahc); +void ahc_unpause(struct ahc_softc *ahc); + +/************************** Memory mapping routines ***************************/ +void ahc_sync_sglist(struct ahc_softc *ahc, + struct scb *scb, int op); + +/******************************** Debugging ***********************************/ +static inline char *ahc_name(struct ahc_softc *ahc); + +static inline char *ahc_name(struct ahc_softc *ahc) +{ + return (ahc->name); +} + +/*********************** Miscellaneous Support Functions ***********************/ + +struct ahc_initiator_tinfo * + ahc_fetch_transinfo(struct ahc_softc *ahc, + char channel, u_int our_id, + u_int remote_id, + struct ahc_tmode_tstate **tstate); +uint16_t + ahc_inw(struct ahc_softc *ahc, u_int port); +void ahc_outw(struct ahc_softc *ahc, u_int port, + u_int value); +uint32_t + ahc_inl(struct ahc_softc *ahc, u_int port); +void ahc_outl(struct ahc_softc *ahc, u_int port, + uint32_t value); +uint64_t + ahc_inq(struct ahc_softc *ahc, u_int port); +void ahc_outq(struct ahc_softc *ahc, u_int port, + uint64_t value); +struct scb* + ahc_get_scb(struct ahc_softc *ahc); +void ahc_free_scb(struct ahc_softc *ahc, struct scb *scb); +struct scb * + ahc_lookup_scb(struct ahc_softc *ahc, u_int tag); +void ahc_queue_scb(struct ahc_softc *ahc, struct scb *scb); +struct scsi_sense_data * + ahc_get_sense_buf(struct ahc_softc *ahc, + struct scb *scb); + +/************************** Interrupt Processing ******************************/ +int ahc_intr(struct ahc_softc *ahc); + +#endif /* _AIC7XXX_INLINE_H_ */ diff --git a/drivers/scsi/aic7xxx/aic7xxx_osm.c b/drivers/scsi/aic7xxx/aic7xxx_osm.c new file mode 100644 index 000000000..7bba961d1 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx_osm.c @@ -0,0 +1,2574 @@ +/* + * Adaptec AIC7xxx device driver for Linux. + * + * $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic7xxx_osm.c#235 $ + * + * Copyright (c) 1994 John Aycock + * The University of Calgary Department of Computer Science. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * Sources include the Adaptec 1740 driver (aha1740.c), the Ultrastor 24F + * driver (ultrastor.c), various Linux kernel source, the Adaptec EISA + * config file (!adp7771.cfg), the Adaptec AHA-2740A Series User's Guide, + * the Linux Kernel Hacker's Guide, Writing a SCSI Device Driver for Linux, + * the Adaptec 1542 driver (aha1542.c), the Adaptec EISA overlay file + * (adp7770.ovl), the Adaptec AHA-2740 Series Technical Reference Manual, + * the Adaptec AIC-7770 Data Book, the ANSI SCSI specification, the + * ANSI SCSI-2 specification (draft 10c), ... + * + * -------------------------------------------------------------------------- + * + * Modifications by Daniel M. Eischen (deischen@iworks.InterWorks.org): + * + * Substantially modified to include support for wide and twin bus + * adapters, DMAing of SCBs, tagged queueing, IRQ sharing, bug fixes, + * SCB paging, and other rework of the code. + * + * -------------------------------------------------------------------------- + * Copyright (c) 1994-2000 Justin T. Gibbs. + * Copyright (c) 2000-2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + *--------------------------------------------------------------------------- + * + * Thanks also go to (in alphabetical order) the following: + * + * Rory Bolt - Sequencer bug fixes + * Jay Estabrook - Initial DEC Alpha support + * Doug Ledford - Much needed abort/reset bug fixes + * Kai Makisara - DMAing of SCBs + * + * A Boot time option was also added for not resetting the scsi bus. + * + * Form: aic7xxx=extended + * aic7xxx=no_reset + * aic7xxx=verbose + * + * Daniel M. Eischen, deischen@iworks.InterWorks.org, 1/23/97 + * + * Id: aic7xxx.c,v 4.1 1997/06/12 08:23:42 deang Exp + */ + +/* + * Further driver modifications made by Doug Ledford <dledford@redhat.com> + * + * Copyright (c) 1997-1999 Doug Ledford + * + * These changes are released under the same licensing terms as the FreeBSD + * driver written by Justin Gibbs. Please see his Copyright notice above + * for the exact terms and conditions covering my changes as well as the + * warranty statement. + * + * Modifications made to the aic7xxx.c,v 4.1 driver from Dan Eischen include + * but are not limited to: + * + * 1: Import of the latest FreeBSD sequencer code for this driver + * 2: Modification of kernel code to accommodate different sequencer semantics + * 3: Extensive changes throughout kernel portion of driver to improve + * abort/reset processing and error hanndling + * 4: Other work contributed by various people on the Internet + * 5: Changes to printk information and verbosity selection code + * 6: General reliability related changes, especially in IRQ management + * 7: Modifications to the default probe/attach order for supported cards + * 8: SMP friendliness has been improved + * + */ + +#include "aic7xxx_osm.h" +#include "aic7xxx_inline.h" +#include <scsi/scsicam.h> + +static struct scsi_transport_template *ahc_linux_transport_template = NULL; + +#include <linux/init.h> /* __setup */ +#include <linux/mm.h> /* For fetching system memory size */ +#include <linux/blkdev.h> /* For block_size() */ +#include <linux/delay.h> /* For ssleep/msleep */ +#include <linux/slab.h> + + +/* + * Set this to the delay in seconds after SCSI bus reset. + * Note, we honor this only for the initial bus reset. + * The scsi error recovery code performs its own bus settle + * delay handling for error recovery actions. + */ +#ifdef CONFIG_AIC7XXX_RESET_DELAY_MS +#define AIC7XXX_RESET_DELAY CONFIG_AIC7XXX_RESET_DELAY_MS +#else +#define AIC7XXX_RESET_DELAY 5000 +#endif + +/* + * To change the default number of tagged transactions allowed per-device, + * add a line to the lilo.conf file like: + * append="aic7xxx=verbose,tag_info:{{32,32,32,32},{32,32,32,32}}" + * which will result in the first four devices on the first two + * controllers being set to a tagged queue depth of 32. + * + * The tag_commands is an array of 16 to allow for wide and twin adapters. + * Twin adapters will use indexes 0-7 for channel 0, and indexes 8-15 + * for channel 1. + */ +typedef struct { + uint8_t tag_commands[16]; /* Allow for wide/twin adapters. */ +} adapter_tag_info_t; + +/* + * Modify this as you see fit for your system. + * + * 0 tagged queuing disabled + * 1 <= n <= 253 n == max tags ever dispatched. + * + * The driver will throttle the number of commands dispatched to a + * device if it returns queue full. For devices with a fixed maximum + * queue depth, the driver will eventually determine this depth and + * lock it in (a console message is printed to indicate that a lock + * has occurred). On some devices, queue full is returned for a temporary + * resource shortage. These devices will return queue full at varying + * depths. The driver will throttle back when the queue fulls occur and + * attempt to slowly increase the depth over time as the device recovers + * from the resource shortage. + * + * In this example, the first line will disable tagged queueing for all + * the devices on the first probed aic7xxx adapter. + * + * The second line enables tagged queueing with 4 commands/LUN for IDs + * (0, 2-11, 13-15), disables tagged queueing for ID 12, and tells the + * driver to attempt to use up to 64 tags for ID 1. + * + * The third line is the same as the first line. + * + * The fourth line disables tagged queueing for devices 0 and 3. It + * enables tagged queueing for the other IDs, with 16 commands/LUN + * for IDs 1 and 4, 127 commands/LUN for ID 8, and 4 commands/LUN for + * IDs 2, 5-7, and 9-15. + */ + +/* + * NOTE: The below structure is for reference only, the actual structure + * to modify in order to change things is just below this comment block. +adapter_tag_info_t aic7xxx_tag_info[] = +{ + {{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}}, + {{4, 64, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 0, 4, 4, 4}}, + {{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}}, + {{0, 16, 4, 0, 16, 4, 4, 4, 127, 4, 4, 4, 4, 4, 4, 4}} +}; +*/ + +#ifdef CONFIG_AIC7XXX_CMDS_PER_DEVICE +#define AIC7XXX_CMDS_PER_DEVICE CONFIG_AIC7XXX_CMDS_PER_DEVICE +#else +#define AIC7XXX_CMDS_PER_DEVICE AHC_MAX_QUEUE +#endif + +#define AIC7XXX_CONFIGED_TAG_COMMANDS { \ + AIC7XXX_CMDS_PER_DEVICE, AIC7XXX_CMDS_PER_DEVICE, \ + AIC7XXX_CMDS_PER_DEVICE, AIC7XXX_CMDS_PER_DEVICE, \ + AIC7XXX_CMDS_PER_DEVICE, AIC7XXX_CMDS_PER_DEVICE, \ + AIC7XXX_CMDS_PER_DEVICE, AIC7XXX_CMDS_PER_DEVICE, \ + AIC7XXX_CMDS_PER_DEVICE, AIC7XXX_CMDS_PER_DEVICE, \ + AIC7XXX_CMDS_PER_DEVICE, AIC7XXX_CMDS_PER_DEVICE, \ + AIC7XXX_CMDS_PER_DEVICE, AIC7XXX_CMDS_PER_DEVICE, \ + AIC7XXX_CMDS_PER_DEVICE, AIC7XXX_CMDS_PER_DEVICE \ +} + +/* + * By default, use the number of commands specified by + * the users kernel configuration. + */ +static adapter_tag_info_t aic7xxx_tag_info[] = +{ + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS}, + {AIC7XXX_CONFIGED_TAG_COMMANDS} +}; + +/* + * There should be a specific return value for this in scsi.h, but + * it seems that most drivers ignore it. + */ +#define DID_UNDERFLOW DID_ERROR + +void +ahc_print_path(struct ahc_softc *ahc, struct scb *scb) +{ + printk("(scsi%d:%c:%d:%d): ", + ahc->platform_data->host->host_no, + scb != NULL ? SCB_GET_CHANNEL(ahc, scb) : 'X', + scb != NULL ? SCB_GET_TARGET(ahc, scb) : -1, + scb != NULL ? SCB_GET_LUN(scb) : -1); +} + +/* + * XXX - these options apply unilaterally to _all_ 274x/284x/294x + * cards in the system. This should be fixed. Exceptions to this + * rule are noted in the comments. + */ + +/* + * Skip the scsi bus reset. Non 0 make us skip the reset at startup. This + * has no effect on any later resets that might occur due to things like + * SCSI bus timeouts. + */ +static uint32_t aic7xxx_no_reset; + +/* + * Should we force EXTENDED translation on a controller. + * 0 == Use whatever is in the SEEPROM or default to off + * 1 == Use whatever is in the SEEPROM or default to on + */ +static uint32_t aic7xxx_extended; + +/* + * PCI bus parity checking of the Adaptec controllers. This is somewhat + * dubious at best. To my knowledge, this option has never actually + * solved a PCI parity problem, but on certain machines with broken PCI + * chipset configurations where stray PCI transactions with bad parity are + * the norm rather than the exception, the error messages can be overwhelming. + * It's included in the driver for completeness. + * 0 = Shut off PCI parity check + * non-0 = reverse polarity pci parity checking + */ +static uint32_t aic7xxx_pci_parity = ~0; + +/* + * There are lots of broken chipsets in the world. Some of them will + * violate the PCI spec when we issue byte sized memory writes to our + * controller. I/O mapped register access, if allowed by the given + * platform, will work in almost all cases. + */ +uint32_t aic7xxx_allow_memio = ~0; + +/* + * So that we can set how long each device is given as a selection timeout. + * The table of values goes like this: + * 0 - 256ms + * 1 - 128ms + * 2 - 64ms + * 3 - 32ms + * We default to 256ms because some older devices need a longer time + * to respond to initial selection. + */ +static uint32_t aic7xxx_seltime; + +/* + * Certain devices do not perform any aging on commands. Should the + * device be saturated by commands in one portion of the disk, it is + * possible for transactions on far away sectors to never be serviced. + * To handle these devices, we can periodically send an ordered tag to + * force all outstanding transactions to be serviced prior to a new + * transaction. + */ +static uint32_t aic7xxx_periodic_otag; + +/* + * Module information and settable options. + */ +static char *aic7xxx = NULL; + +MODULE_AUTHOR("Maintainer: Hannes Reinecke <hare@suse.de>"); +MODULE_DESCRIPTION("Adaptec AIC77XX/78XX SCSI Host Bus Adapter driver"); +MODULE_LICENSE("Dual BSD/GPL"); +MODULE_VERSION(AIC7XXX_DRIVER_VERSION); +module_param(aic7xxx, charp, 0444); +MODULE_PARM_DESC(aic7xxx, +"period-delimited options string:\n" +" verbose Enable verbose/diagnostic logging\n" +" allow_memio Allow device registers to be memory mapped\n" +" debug Bitmask of debug values to enable\n" +" no_probe Toggle EISA/VLB controller probing\n" +" probe_eisa_vl Toggle EISA/VLB controller probing\n" +" no_reset Suppress initial bus resets\n" +" extended Enable extended geometry on all controllers\n" +" periodic_otag Send an ordered tagged transaction\n" +" periodically to prevent tag starvation.\n" +" This may be required by some older disk\n" +" drives or RAID arrays.\n" +" tag_info:<tag_str> Set per-target tag depth\n" +" global_tag_depth:<int> Global tag depth for every target\n" +" on every bus\n" +" seltime:<int> Selection Timeout\n" +" (0/256ms,1/128ms,2/64ms,3/32ms)\n" +"\n" +" Sample modprobe configuration file:\n" +" # Toggle EISA/VLB probing\n" +" # Set tag depth on Controller 1/Target 1 to 10 tags\n" +" # Shorten the selection timeout to 128ms\n" +"\n" +" options aic7xxx 'aic7xxx=probe_eisa_vl.tag_info:{{}.{.10}}.seltime:1'\n" +); + +static void ahc_linux_handle_scsi_status(struct ahc_softc *, + struct scsi_device *, + struct scb *); +static void ahc_linux_queue_cmd_complete(struct ahc_softc *ahc, + struct scsi_cmnd *cmd); +static void ahc_linux_freeze_simq(struct ahc_softc *ahc); +static void ahc_linux_release_simq(struct ahc_softc *ahc); +static int ahc_linux_queue_recovery_cmd(struct scsi_cmnd *cmd, scb_flag flag); +static void ahc_linux_initialize_scsi_bus(struct ahc_softc *ahc); +static u_int ahc_linux_user_tagdepth(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo); +static void ahc_linux_device_queue_depth(struct scsi_device *); +static int ahc_linux_run_command(struct ahc_softc*, + struct ahc_linux_device *, + struct scsi_cmnd *); +static void ahc_linux_setup_tag_info_global(char *p); +static int aic7xxx_setup(char *s); + +static int ahc_linux_unit; + + +/************************** OS Utility Wrappers *******************************/ +void +ahc_delay(long usec) +{ + /* + * udelay on Linux can have problems for + * multi-millisecond waits. Wait at most + * 1024us per call. + */ + while (usec > 0) { + udelay(usec % 1024); + usec -= 1024; + } +} + +/***************************** Low Level I/O **********************************/ +uint8_t +ahc_inb(struct ahc_softc * ahc, long port) +{ + uint8_t x; + + if (ahc->tag == BUS_SPACE_MEMIO) { + x = readb(ahc->bsh.maddr + port); + } else { + x = inb(ahc->bsh.ioport + port); + } + mb(); + return (x); +} + +void +ahc_outb(struct ahc_softc * ahc, long port, uint8_t val) +{ + if (ahc->tag == BUS_SPACE_MEMIO) { + writeb(val, ahc->bsh.maddr + port); + } else { + outb(val, ahc->bsh.ioport + port); + } + mb(); +} + +void +ahc_outsb(struct ahc_softc * ahc, long port, uint8_t *array, int count) +{ + int i; + + /* + * There is probably a more efficient way to do this on Linux + * but we don't use this for anything speed critical and this + * should work. + */ + for (i = 0; i < count; i++) + ahc_outb(ahc, port, *array++); +} + +void +ahc_insb(struct ahc_softc * ahc, long port, uint8_t *array, int count) +{ + int i; + + /* + * There is probably a more efficient way to do this on Linux + * but we don't use this for anything speed critical and this + * should work. + */ + for (i = 0; i < count; i++) + *array++ = ahc_inb(ahc, port); +} + +/********************************* Inlines ************************************/ +static void ahc_linux_unmap_scb(struct ahc_softc*, struct scb*); + +static int ahc_linux_map_seg(struct ahc_softc *ahc, struct scb *scb, + struct ahc_dma_seg *sg, + dma_addr_t addr, bus_size_t len); + +static void +ahc_linux_unmap_scb(struct ahc_softc *ahc, struct scb *scb) +{ + struct scsi_cmnd *cmd; + + cmd = scb->io_ctx; + ahc_sync_sglist(ahc, scb, BUS_DMASYNC_POSTWRITE); + + scsi_dma_unmap(cmd); +} + +static int +ahc_linux_map_seg(struct ahc_softc *ahc, struct scb *scb, + struct ahc_dma_seg *sg, dma_addr_t addr, bus_size_t len) +{ + int consumed; + + if ((scb->sg_count + 1) > AHC_NSEG) + panic("Too few segs for dma mapping. " + "Increase AHC_NSEG\n"); + + consumed = 1; + sg->addr = ahc_htole32(addr & 0xFFFFFFFF); + scb->platform_data->xfer_len += len; + + if (sizeof(dma_addr_t) > 4 + && (ahc->flags & AHC_39BIT_ADDRESSING) != 0) + len |= (addr >> 8) & AHC_SG_HIGH_ADDR_MASK; + + sg->len = ahc_htole32(len); + return (consumed); +} + +/* + * Return a string describing the driver. + */ +static const char * +ahc_linux_info(struct Scsi_Host *host) +{ + static char buffer[512]; + char ahc_info[256]; + char *bp; + struct ahc_softc *ahc; + + bp = &buffer[0]; + ahc = *(struct ahc_softc **)host->hostdata; + memset(bp, 0, sizeof(buffer)); + strcpy(bp, "Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev " AIC7XXX_DRIVER_VERSION "\n" + " <"); + strcat(bp, ahc->description); + strcat(bp, ">\n" + " "); + ahc_controller_info(ahc, ahc_info); + strcat(bp, ahc_info); + strcat(bp, "\n"); + + return (bp); +} + +/* + * Queue an SCB to the controller. + */ +static int +ahc_linux_queue_lck(struct scsi_cmnd * cmd, void (*scsi_done) (struct scsi_cmnd *)) +{ + struct ahc_softc *ahc; + struct ahc_linux_device *dev = scsi_transport_device_data(cmd->device); + int rtn = SCSI_MLQUEUE_HOST_BUSY; + unsigned long flags; + + ahc = *(struct ahc_softc **)cmd->device->host->hostdata; + + ahc_lock(ahc, &flags); + if (ahc->platform_data->qfrozen == 0) { + cmd->scsi_done = scsi_done; + cmd->result = CAM_REQ_INPROG << 16; + rtn = ahc_linux_run_command(ahc, dev, cmd); + } + ahc_unlock(ahc, &flags); + + return rtn; +} + +static DEF_SCSI_QCMD(ahc_linux_queue) + +static inline struct scsi_target ** +ahc_linux_target_in_softc(struct scsi_target *starget) +{ + struct ahc_softc *ahc = + *((struct ahc_softc **)dev_to_shost(&starget->dev)->hostdata); + unsigned int target_offset; + + target_offset = starget->id; + if (starget->channel != 0) + target_offset += 8; + + return &ahc->platform_data->starget[target_offset]; +} + +static int +ahc_linux_target_alloc(struct scsi_target *starget) +{ + struct ahc_softc *ahc = + *((struct ahc_softc **)dev_to_shost(&starget->dev)->hostdata); + struct seeprom_config *sc = ahc->seep_config; + unsigned long flags; + struct scsi_target **ahc_targp = ahc_linux_target_in_softc(starget); + unsigned short scsirate; + struct ahc_devinfo devinfo; + char channel = starget->channel + 'A'; + unsigned int our_id = ahc->our_id; + unsigned int target_offset; + + target_offset = starget->id; + if (starget->channel != 0) + target_offset += 8; + + if (starget->channel) + our_id = ahc->our_id_b; + + ahc_lock(ahc, &flags); + + BUG_ON(*ahc_targp != NULL); + + *ahc_targp = starget; + + if (sc) { + int maxsync = AHC_SYNCRATE_DT; + int ultra = 0; + int flags = sc->device_flags[target_offset]; + + if (ahc->flags & AHC_NEWEEPROM_FMT) { + if (flags & CFSYNCHISULTRA) + ultra = 1; + } else if (flags & CFULTRAEN) + ultra = 1; + /* AIC nutcase; 10MHz appears as ultra = 1, CFXFER = 0x04 + * change it to ultra=0, CFXFER = 0 */ + if(ultra && (flags & CFXFER) == 0x04) { + ultra = 0; + flags &= ~CFXFER; + } + + if ((ahc->features & AHC_ULTRA2) != 0) { + scsirate = (flags & CFXFER) | (ultra ? 0x8 : 0); + } else { + scsirate = (flags & CFXFER) << 4; + maxsync = ultra ? AHC_SYNCRATE_ULTRA : + AHC_SYNCRATE_FAST; + } + spi_max_width(starget) = (flags & CFWIDEB) ? 1 : 0; + if (!(flags & CFSYNCH)) + spi_max_offset(starget) = 0; + spi_min_period(starget) = + ahc_find_period(ahc, scsirate, maxsync); + } + ahc_compile_devinfo(&devinfo, our_id, starget->id, + CAM_LUN_WILDCARD, channel, + ROLE_INITIATOR); + ahc_set_syncrate(ahc, &devinfo, NULL, 0, 0, 0, + AHC_TRANS_GOAL, /*paused*/FALSE); + ahc_set_width(ahc, &devinfo, MSG_EXT_WDTR_BUS_8_BIT, + AHC_TRANS_GOAL, /*paused*/FALSE); + ahc_unlock(ahc, &flags); + + return 0; +} + +static void +ahc_linux_target_destroy(struct scsi_target *starget) +{ + struct scsi_target **ahc_targp = ahc_linux_target_in_softc(starget); + + *ahc_targp = NULL; +} + +static int +ahc_linux_slave_alloc(struct scsi_device *sdev) +{ + struct ahc_softc *ahc = + *((struct ahc_softc **)sdev->host->hostdata); + struct scsi_target *starget = sdev->sdev_target; + struct ahc_linux_device *dev; + + if (bootverbose) + printk("%s: Slave Alloc %d\n", ahc_name(ahc), sdev->id); + + dev = scsi_transport_device_data(sdev); + memset(dev, 0, sizeof(*dev)); + + /* + * We start out life using untagged + * transactions of which we allow one. + */ + dev->openings = 1; + + /* + * Set maxtags to 0. This will be changed if we + * later determine that we are dealing with + * a tagged queuing capable device. + */ + dev->maxtags = 0; + + spi_period(starget) = 0; + + return 0; +} + +static int +ahc_linux_slave_configure(struct scsi_device *sdev) +{ + if (bootverbose) + sdev_printk(KERN_INFO, sdev, "Slave Configure\n"); + + ahc_linux_device_queue_depth(sdev); + + /* Initial Domain Validation */ + if (!spi_initial_dv(sdev->sdev_target)) + spi_dv_device(sdev); + + return 0; +} + +#if defined(__i386__) +/* + * Return the disk geometry for the given SCSI device. + */ +static int +ahc_linux_biosparam(struct scsi_device *sdev, struct block_device *bdev, + sector_t capacity, int geom[]) +{ + int heads; + int sectors; + int cylinders; + int extended; + struct ahc_softc *ahc; + u_int channel; + + ahc = *((struct ahc_softc **)sdev->host->hostdata); + channel = sdev_channel(sdev); + + if (scsi_partsize(bdev, capacity, geom)) + return 0; + + heads = 64; + sectors = 32; + cylinders = aic_sector_div(capacity, heads, sectors); + + if (aic7xxx_extended != 0) + extended = 1; + else if (channel == 0) + extended = (ahc->flags & AHC_EXTENDED_TRANS_A) != 0; + else + extended = (ahc->flags & AHC_EXTENDED_TRANS_B) != 0; + if (extended && cylinders >= 1024) { + heads = 255; + sectors = 63; + cylinders = aic_sector_div(capacity, heads, sectors); + } + geom[0] = heads; + geom[1] = sectors; + geom[2] = cylinders; + return (0); +} +#endif + +/* + * Abort the current SCSI command(s). + */ +static int +ahc_linux_abort(struct scsi_cmnd *cmd) +{ + int error; + + error = ahc_linux_queue_recovery_cmd(cmd, SCB_ABORT); + if (error != SUCCESS) + printk("aic7xxx_abort returns 0x%x\n", error); + return (error); +} + +/* + * Attempt to send a target reset message to the device that timed out. + */ +static int +ahc_linux_dev_reset(struct scsi_cmnd *cmd) +{ + int error; + + error = ahc_linux_queue_recovery_cmd(cmd, SCB_DEVICE_RESET); + if (error != SUCCESS) + printk("aic7xxx_dev_reset returns 0x%x\n", error); + return (error); +} + +/* + * Reset the SCSI bus. + */ +static int +ahc_linux_bus_reset(struct scsi_cmnd *cmd) +{ + struct ahc_softc *ahc; + int found; + unsigned long flags; + + ahc = *(struct ahc_softc **)cmd->device->host->hostdata; + + ahc_lock(ahc, &flags); + found = ahc_reset_channel(ahc, scmd_channel(cmd) + 'A', + /*initiate reset*/TRUE); + ahc_unlock(ahc, &flags); + + if (bootverbose) + printk("%s: SCSI bus reset delivered. " + "%d SCBs aborted.\n", ahc_name(ahc), found); + + return SUCCESS; +} + +struct scsi_host_template aic7xxx_driver_template = { + .module = THIS_MODULE, + .name = "aic7xxx", + .proc_name = "aic7xxx", + .show_info = ahc_linux_show_info, + .write_info = ahc_proc_write_seeprom, + .info = ahc_linux_info, + .queuecommand = ahc_linux_queue, + .eh_abort_handler = ahc_linux_abort, + .eh_device_reset_handler = ahc_linux_dev_reset, + .eh_bus_reset_handler = ahc_linux_bus_reset, +#if defined(__i386__) + .bios_param = ahc_linux_biosparam, +#endif + .can_queue = AHC_MAX_QUEUE, + .this_id = -1, + .max_sectors = 8192, + .cmd_per_lun = 2, + .slave_alloc = ahc_linux_slave_alloc, + .slave_configure = ahc_linux_slave_configure, + .target_alloc = ahc_linux_target_alloc, + .target_destroy = ahc_linux_target_destroy, +}; + +/**************************** Tasklet Handler *********************************/ + +/******************************** Macros **************************************/ +#define BUILD_SCSIID(ahc, cmd) \ + ((((cmd)->device->id << TID_SHIFT) & TID) \ + | (((cmd)->device->channel == 0) ? (ahc)->our_id : (ahc)->our_id_b) \ + | (((cmd)->device->channel == 0) ? 0 : TWIN_CHNLB)) + +/******************************** Bus DMA *************************************/ +int +ahc_dma_tag_create(struct ahc_softc *ahc, bus_dma_tag_t parent, + bus_size_t alignment, bus_size_t boundary, + dma_addr_t lowaddr, dma_addr_t highaddr, + bus_dma_filter_t *filter, void *filterarg, + bus_size_t maxsize, int nsegments, + bus_size_t maxsegsz, int flags, bus_dma_tag_t *ret_tag) +{ + bus_dma_tag_t dmat; + + dmat = kmalloc(sizeof(*dmat), GFP_ATOMIC); + if (dmat == NULL) + return (ENOMEM); + + /* + * Linux is very simplistic about DMA memory. For now don't + * maintain all specification information. Once Linux supplies + * better facilities for doing these operations, or the + * needs of this particular driver change, we might need to do + * more here. + */ + dmat->alignment = alignment; + dmat->boundary = boundary; + dmat->maxsize = maxsize; + *ret_tag = dmat; + return (0); +} + +void +ahc_dma_tag_destroy(struct ahc_softc *ahc, bus_dma_tag_t dmat) +{ + kfree(dmat); +} + +int +ahc_dmamem_alloc(struct ahc_softc *ahc, bus_dma_tag_t dmat, void** vaddr, + int flags, bus_dmamap_t *mapp) +{ + /* XXX: check if we really need the GFP_ATOMIC and unwind this mess! */ + *vaddr = dma_alloc_coherent(ahc->dev, dmat->maxsize, mapp, GFP_ATOMIC); + if (*vaddr == NULL) + return ENOMEM; + return 0; +} + +void +ahc_dmamem_free(struct ahc_softc *ahc, bus_dma_tag_t dmat, + void* vaddr, bus_dmamap_t map) +{ + dma_free_coherent(ahc->dev, dmat->maxsize, vaddr, map); +} + +int +ahc_dmamap_load(struct ahc_softc *ahc, bus_dma_tag_t dmat, bus_dmamap_t map, + void *buf, bus_size_t buflen, bus_dmamap_callback_t *cb, + void *cb_arg, int flags) +{ + /* + * Assume for now that this will only be used during + * initialization and not for per-transaction buffer mapping. + */ + bus_dma_segment_t stack_sg; + + stack_sg.ds_addr = map; + stack_sg.ds_len = dmat->maxsize; + cb(cb_arg, &stack_sg, /*nseg*/1, /*error*/0); + return (0); +} + +void +ahc_dmamap_destroy(struct ahc_softc *ahc, bus_dma_tag_t dmat, bus_dmamap_t map) +{ +} + +int +ahc_dmamap_unload(struct ahc_softc *ahc, bus_dma_tag_t dmat, bus_dmamap_t map) +{ + /* Nothing to do */ + return (0); +} + +static void +ahc_linux_setup_tag_info_global(char *p) +{ + int tags, i, j; + + tags = simple_strtoul(p + 1, NULL, 0) & 0xff; + printk("Setting Global Tags= %d\n", tags); + + for (i = 0; i < ARRAY_SIZE(aic7xxx_tag_info); i++) { + for (j = 0; j < AHC_NUM_TARGETS; j++) { + aic7xxx_tag_info[i].tag_commands[j] = tags; + } + } +} + +static void +ahc_linux_setup_tag_info(u_long arg, int instance, int targ, int32_t value) +{ + + if ((instance >= 0) && (targ >= 0) + && (instance < ARRAY_SIZE(aic7xxx_tag_info)) + && (targ < AHC_NUM_TARGETS)) { + aic7xxx_tag_info[instance].tag_commands[targ] = value & 0xff; + if (bootverbose) + printk("tag_info[%d:%d] = %d\n", instance, targ, value); + } +} + +static char * +ahc_parse_brace_option(char *opt_name, char *opt_arg, char *end, int depth, + void (*callback)(u_long, int, int, int32_t), + u_long callback_arg) +{ + char *tok_end; + char *tok_end2; + int i; + int instance; + int targ; + int done; + char tok_list[] = {'.', ',', '{', '}', '\0'}; + + /* All options use a ':' name/arg separator */ + if (*opt_arg != ':') + return (opt_arg); + opt_arg++; + instance = -1; + targ = -1; + done = FALSE; + /* + * Restore separator that may be in + * the middle of our option argument. + */ + tok_end = strchr(opt_arg, '\0'); + if (tok_end < end) + *tok_end = ','; + while (!done) { + switch (*opt_arg) { + case '{': + if (instance == -1) { + instance = 0; + } else { + if (depth > 1) { + if (targ == -1) + targ = 0; + } else { + printk("Malformed Option %s\n", + opt_name); + done = TRUE; + } + } + opt_arg++; + break; + case '}': + if (targ != -1) + targ = -1; + else if (instance != -1) + instance = -1; + opt_arg++; + break; + case ',': + case '.': + if (instance == -1) + done = TRUE; + else if (targ >= 0) + targ++; + else if (instance >= 0) + instance++; + opt_arg++; + break; + case '\0': + done = TRUE; + break; + default: + tok_end = end; + for (i = 0; tok_list[i]; i++) { + tok_end2 = strchr(opt_arg, tok_list[i]); + if ((tok_end2) && (tok_end2 < tok_end)) + tok_end = tok_end2; + } + callback(callback_arg, instance, targ, + simple_strtol(opt_arg, NULL, 0)); + opt_arg = tok_end; + break; + } + } + return (opt_arg); +} + +/* + * Handle Linux boot parameters. This routine allows for assigning a value + * to a parameter with a ':' between the parameter and the value. + * ie. aic7xxx=stpwlev:1,extended + */ +static int +aic7xxx_setup(char *s) +{ + int i, n; + char *p; + char *end; + + static const struct { + const char *name; + uint32_t *flag; + } options[] = { + { "extended", &aic7xxx_extended }, + { "no_reset", &aic7xxx_no_reset }, + { "verbose", &aic7xxx_verbose }, + { "allow_memio", &aic7xxx_allow_memio}, +#ifdef AHC_DEBUG + { "debug", &ahc_debug }, +#endif + { "periodic_otag", &aic7xxx_periodic_otag }, + { "pci_parity", &aic7xxx_pci_parity }, + { "seltime", &aic7xxx_seltime }, + { "tag_info", NULL }, + { "global_tag_depth", NULL }, + { "dv", NULL } + }; + + end = strchr(s, '\0'); + + /* + * XXX ia64 gcc isn't smart enough to know that ARRAY_SIZE + * will never be 0 in this case. + */ + n = 0; + + while ((p = strsep(&s, ",.")) != NULL) { + if (*p == '\0') + continue; + for (i = 0; i < ARRAY_SIZE(options); i++) { + + n = strlen(options[i].name); + if (strncmp(options[i].name, p, n) == 0) + break; + } + if (i == ARRAY_SIZE(options)) + continue; + + if (strncmp(p, "global_tag_depth", n) == 0) { + ahc_linux_setup_tag_info_global(p + n); + } else if (strncmp(p, "tag_info", n) == 0) { + s = ahc_parse_brace_option("tag_info", p + n, end, + 2, ahc_linux_setup_tag_info, 0); + } else if (p[n] == ':') { + *(options[i].flag) = simple_strtoul(p + n + 1, NULL, 0); + } else if (strncmp(p, "verbose", n) == 0) { + *(options[i].flag) = 1; + } else { + *(options[i].flag) ^= 0xFFFFFFFF; + } + } + return 1; +} + +__setup("aic7xxx=", aic7xxx_setup); + +uint32_t aic7xxx_verbose; + +int +ahc_linux_register_host(struct ahc_softc *ahc, struct scsi_host_template *template) +{ + char buf[80]; + struct Scsi_Host *host; + char *new_name; + u_long s; + int retval; + + template->name = ahc->description; + host = scsi_host_alloc(template, sizeof(struct ahc_softc *)); + if (host == NULL) + return (ENOMEM); + + *((struct ahc_softc **)host->hostdata) = ahc; + ahc->platform_data->host = host; + host->can_queue = AHC_MAX_QUEUE; + host->cmd_per_lun = 2; + /* XXX No way to communicate the ID for multiple channels */ + host->this_id = ahc->our_id; + host->irq = ahc->platform_data->irq; + host->max_id = (ahc->features & AHC_WIDE) ? 16 : 8; + host->max_lun = AHC_NUM_LUNS; + host->max_channel = (ahc->features & AHC_TWIN) ? 1 : 0; + host->sg_tablesize = AHC_NSEG; + ahc_lock(ahc, &s); + ahc_set_unit(ahc, ahc_linux_unit++); + ahc_unlock(ahc, &s); + sprintf(buf, "scsi%d", host->host_no); + new_name = kmalloc(strlen(buf) + 1, GFP_ATOMIC); + if (new_name != NULL) { + strcpy(new_name, buf); + ahc_set_name(ahc, new_name); + } + host->unique_id = ahc->unit; + ahc_linux_initialize_scsi_bus(ahc); + ahc_intr_enable(ahc, TRUE); + + host->transportt = ahc_linux_transport_template; + + retval = scsi_add_host(host, ahc->dev); + if (retval) { + printk(KERN_WARNING "aic7xxx: scsi_add_host failed\n"); + scsi_host_put(host); + return retval; + } + + scsi_scan_host(host); + return 0; +} + +/* + * Place the SCSI bus into a known state by either resetting it, + * or forcing transfer negotiations on the next command to any + * target. + */ +static void +ahc_linux_initialize_scsi_bus(struct ahc_softc *ahc) +{ + int i; + int numtarg; + unsigned long s; + + i = 0; + numtarg = 0; + + ahc_lock(ahc, &s); + + if (aic7xxx_no_reset != 0) + ahc->flags &= ~(AHC_RESET_BUS_A|AHC_RESET_BUS_B); + + if ((ahc->flags & AHC_RESET_BUS_A) != 0) + ahc_reset_channel(ahc, 'A', /*initiate_reset*/TRUE); + else + numtarg = (ahc->features & AHC_WIDE) ? 16 : 8; + + if ((ahc->features & AHC_TWIN) != 0) { + + if ((ahc->flags & AHC_RESET_BUS_B) != 0) { + ahc_reset_channel(ahc, 'B', /*initiate_reset*/TRUE); + } else { + if (numtarg == 0) + i = 8; + numtarg += 8; + } + } + + /* + * Force negotiation to async for all targets that + * will not see an initial bus reset. + */ + for (; i < numtarg; i++) { + struct ahc_devinfo devinfo; + struct ahc_initiator_tinfo *tinfo; + struct ahc_tmode_tstate *tstate; + u_int our_id; + u_int target_id; + char channel; + + channel = 'A'; + our_id = ahc->our_id; + target_id = i; + if (i > 7 && (ahc->features & AHC_TWIN) != 0) { + channel = 'B'; + our_id = ahc->our_id_b; + target_id = i % 8; + } + tinfo = ahc_fetch_transinfo(ahc, channel, our_id, + target_id, &tstate); + ahc_compile_devinfo(&devinfo, our_id, target_id, + CAM_LUN_WILDCARD, channel, ROLE_INITIATOR); + ahc_update_neg_request(ahc, &devinfo, tstate, + tinfo, AHC_NEG_ALWAYS); + } + ahc_unlock(ahc, &s); + /* Give the bus some time to recover */ + if ((ahc->flags & (AHC_RESET_BUS_A|AHC_RESET_BUS_B)) != 0) { + ahc_linux_freeze_simq(ahc); + msleep(AIC7XXX_RESET_DELAY); + ahc_linux_release_simq(ahc); + } +} + +int +ahc_platform_alloc(struct ahc_softc *ahc, void *platform_arg) +{ + + ahc->platform_data = + kzalloc(sizeof(struct ahc_platform_data), GFP_ATOMIC); + if (ahc->platform_data == NULL) + return (ENOMEM); + ahc->platform_data->irq = AHC_LINUX_NOIRQ; + ahc_lockinit(ahc); + ahc->seltime = (aic7xxx_seltime & 0x3) << 4; + ahc->seltime_b = (aic7xxx_seltime & 0x3) << 4; + if (aic7xxx_pci_parity == 0) + ahc->flags |= AHC_DISABLE_PCI_PERR; + + return (0); +} + +void +ahc_platform_free(struct ahc_softc *ahc) +{ + struct scsi_target *starget; + int i; + + if (ahc->platform_data != NULL) { + /* destroy all of the device and target objects */ + for (i = 0; i < AHC_NUM_TARGETS; i++) { + starget = ahc->platform_data->starget[i]; + if (starget != NULL) { + ahc->platform_data->starget[i] = NULL; + } + } + + if (ahc->platform_data->irq != AHC_LINUX_NOIRQ) + free_irq(ahc->platform_data->irq, ahc); + if (ahc->tag == BUS_SPACE_PIO + && ahc->bsh.ioport != 0) + release_region(ahc->bsh.ioport, 256); + if (ahc->tag == BUS_SPACE_MEMIO + && ahc->bsh.maddr != NULL) { + iounmap(ahc->bsh.maddr); + release_mem_region(ahc->platform_data->mem_busaddr, + 0x1000); + } + + if (ahc->platform_data->host) + scsi_host_put(ahc->platform_data->host); + + kfree(ahc->platform_data); + } +} + +void +ahc_platform_freeze_devq(struct ahc_softc *ahc, struct scb *scb) +{ + ahc_platform_abort_scbs(ahc, SCB_GET_TARGET(ahc, scb), + SCB_GET_CHANNEL(ahc, scb), + SCB_GET_LUN(scb), SCB_LIST_NULL, + ROLE_UNKNOWN, CAM_REQUEUE_REQ); +} + +void +ahc_platform_set_tags(struct ahc_softc *ahc, struct scsi_device *sdev, + struct ahc_devinfo *devinfo, ahc_queue_alg alg) +{ + struct ahc_linux_device *dev; + int was_queuing; + int now_queuing; + + if (sdev == NULL) + return; + dev = scsi_transport_device_data(sdev); + + was_queuing = dev->flags & (AHC_DEV_Q_BASIC|AHC_DEV_Q_TAGGED); + switch (alg) { + default: + case AHC_QUEUE_NONE: + now_queuing = 0; + break; + case AHC_QUEUE_BASIC: + now_queuing = AHC_DEV_Q_BASIC; + break; + case AHC_QUEUE_TAGGED: + now_queuing = AHC_DEV_Q_TAGGED; + break; + } + if ((dev->flags & AHC_DEV_FREEZE_TIL_EMPTY) == 0 + && (was_queuing != now_queuing) + && (dev->active != 0)) { + dev->flags |= AHC_DEV_FREEZE_TIL_EMPTY; + dev->qfrozen++; + } + + dev->flags &= ~(AHC_DEV_Q_BASIC|AHC_DEV_Q_TAGGED|AHC_DEV_PERIODIC_OTAG); + if (now_queuing) { + u_int usertags; + + usertags = ahc_linux_user_tagdepth(ahc, devinfo); + if (!was_queuing) { + /* + * Start out aggressively and allow our + * dynamic queue depth algorithm to take + * care of the rest. + */ + dev->maxtags = usertags; + dev->openings = dev->maxtags - dev->active; + } + if (dev->maxtags == 0) { + /* + * Queueing is disabled by the user. + */ + dev->openings = 1; + } else if (alg == AHC_QUEUE_TAGGED) { + dev->flags |= AHC_DEV_Q_TAGGED; + if (aic7xxx_periodic_otag != 0) + dev->flags |= AHC_DEV_PERIODIC_OTAG; + } else + dev->flags |= AHC_DEV_Q_BASIC; + } else { + /* We can only have one opening. */ + dev->maxtags = 0; + dev->openings = 1 - dev->active; + } + switch ((dev->flags & (AHC_DEV_Q_BASIC|AHC_DEV_Q_TAGGED))) { + case AHC_DEV_Q_BASIC: + case AHC_DEV_Q_TAGGED: + scsi_change_queue_depth(sdev, + dev->openings + dev->active); + break; + default: + /* + * We allow the OS to queue 2 untagged transactions to + * us at any time even though we can only execute them + * serially on the controller/device. This should + * remove some latency. + */ + scsi_change_queue_depth(sdev, 2); + break; + } +} + +int +ahc_platform_abort_scbs(struct ahc_softc *ahc, int target, char channel, + int lun, u_int tag, role_t role, uint32_t status) +{ + return 0; +} + +static u_int +ahc_linux_user_tagdepth(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) +{ + static int warned_user; + u_int tags; + + tags = 0; + if ((ahc->user_discenable & devinfo->target_mask) != 0) { + if (ahc->unit >= ARRAY_SIZE(aic7xxx_tag_info)) { + if (warned_user == 0) { + + printk(KERN_WARNING +"aic7xxx: WARNING: Insufficient tag_info instances\n" +"aic7xxx: for installed controllers. Using defaults\n" +"aic7xxx: Please update the aic7xxx_tag_info array in\n" +"aic7xxx: the aic7xxx_osm..c source file.\n"); + warned_user++; + } + tags = AHC_MAX_QUEUE; + } else { + adapter_tag_info_t *tag_info; + + tag_info = &aic7xxx_tag_info[ahc->unit]; + tags = tag_info->tag_commands[devinfo->target_offset]; + if (tags > AHC_MAX_QUEUE) + tags = AHC_MAX_QUEUE; + } + } + return (tags); +} + +/* + * Determines the queue depth for a given device. + */ +static void +ahc_linux_device_queue_depth(struct scsi_device *sdev) +{ + struct ahc_devinfo devinfo; + u_int tags; + struct ahc_softc *ahc = *((struct ahc_softc **)sdev->host->hostdata); + + ahc_compile_devinfo(&devinfo, + sdev->sdev_target->channel == 0 + ? ahc->our_id : ahc->our_id_b, + sdev->sdev_target->id, sdev->lun, + sdev->sdev_target->channel == 0 ? 'A' : 'B', + ROLE_INITIATOR); + tags = ahc_linux_user_tagdepth(ahc, &devinfo); + if (tags != 0 && sdev->tagged_supported != 0) { + + ahc_platform_set_tags(ahc, sdev, &devinfo, AHC_QUEUE_TAGGED); + ahc_send_async(ahc, devinfo.channel, devinfo.target, + devinfo.lun, AC_TRANSFER_NEG); + ahc_print_devinfo(ahc, &devinfo); + printk("Tagged Queuing enabled. Depth %d\n", tags); + } else { + ahc_platform_set_tags(ahc, sdev, &devinfo, AHC_QUEUE_NONE); + ahc_send_async(ahc, devinfo.channel, devinfo.target, + devinfo.lun, AC_TRANSFER_NEG); + } +} + +static int +ahc_linux_run_command(struct ahc_softc *ahc, struct ahc_linux_device *dev, + struct scsi_cmnd *cmd) +{ + struct scb *scb; + struct hardware_scb *hscb; + struct ahc_initiator_tinfo *tinfo; + struct ahc_tmode_tstate *tstate; + uint16_t mask; + struct scb_tailq *untagged_q = NULL; + int nseg; + + /* + * Schedule us to run later. The only reason we are not + * running is because the whole controller Q is frozen. + */ + if (ahc->platform_data->qfrozen != 0) + return SCSI_MLQUEUE_HOST_BUSY; + + /* + * We only allow one untagged transaction + * per target in the initiator role unless + * we are storing a full busy target *lun* + * table in SCB space. + */ + if (!(cmd->flags & SCMD_TAGGED) + && (ahc->features & AHC_SCB_BTT) == 0) { + int target_offset; + + target_offset = cmd->device->id + cmd->device->channel * 8; + untagged_q = &(ahc->untagged_queues[target_offset]); + if (!TAILQ_EMPTY(untagged_q)) + /* if we're already executing an untagged command + * we're busy to another */ + return SCSI_MLQUEUE_DEVICE_BUSY; + } + + nseg = scsi_dma_map(cmd); + if (nseg < 0) + return SCSI_MLQUEUE_HOST_BUSY; + + /* + * Get an scb to use. + */ + scb = ahc_get_scb(ahc); + if (!scb) { + scsi_dma_unmap(cmd); + return SCSI_MLQUEUE_HOST_BUSY; + } + + scb->io_ctx = cmd; + scb->platform_data->dev = dev; + hscb = scb->hscb; + cmd->host_scribble = (char *)scb; + + /* + * Fill out basics of the HSCB. + */ + hscb->control = 0; + hscb->scsiid = BUILD_SCSIID(ahc, cmd); + hscb->lun = cmd->device->lun; + mask = SCB_GET_TARGET_MASK(ahc, scb); + tinfo = ahc_fetch_transinfo(ahc, SCB_GET_CHANNEL(ahc, scb), + SCB_GET_OUR_ID(scb), + SCB_GET_TARGET(ahc, scb), &tstate); + hscb->scsirate = tinfo->scsirate; + hscb->scsioffset = tinfo->curr.offset; + if ((tstate->ultraenb & mask) != 0) + hscb->control |= ULTRAENB; + + if ((ahc->user_discenable & mask) != 0) + hscb->control |= DISCENB; + + if ((tstate->auto_negotiate & mask) != 0) { + scb->flags |= SCB_AUTO_NEGOTIATE; + scb->hscb->control |= MK_MESSAGE; + } + + if ((dev->flags & (AHC_DEV_Q_TAGGED|AHC_DEV_Q_BASIC)) != 0) { + if (dev->commands_since_idle_or_otag == AHC_OTAG_THRESH + && (dev->flags & AHC_DEV_Q_TAGGED) != 0) { + hscb->control |= MSG_ORDERED_TASK; + dev->commands_since_idle_or_otag = 0; + } else { + hscb->control |= MSG_SIMPLE_TASK; + } + } + + hscb->cdb_len = cmd->cmd_len; + if (hscb->cdb_len <= 12) { + memcpy(hscb->shared_data.cdb, cmd->cmnd, hscb->cdb_len); + } else { + memcpy(hscb->cdb32, cmd->cmnd, hscb->cdb_len); + scb->flags |= SCB_CDB32_PTR; + } + + scb->platform_data->xfer_len = 0; + ahc_set_residual(scb, 0); + ahc_set_sense_residual(scb, 0); + scb->sg_count = 0; + + if (nseg > 0) { + struct ahc_dma_seg *sg; + struct scatterlist *cur_seg; + int i; + + /* Copy the segments into the SG list. */ + sg = scb->sg_list; + /* + * The sg_count may be larger than nseg if + * a transfer crosses a 32bit page. + */ + scsi_for_each_sg(cmd, cur_seg, nseg, i) { + dma_addr_t addr; + bus_size_t len; + int consumed; + + addr = sg_dma_address(cur_seg); + len = sg_dma_len(cur_seg); + consumed = ahc_linux_map_seg(ahc, scb, + sg, addr, len); + sg += consumed; + scb->sg_count += consumed; + } + sg--; + sg->len |= ahc_htole32(AHC_DMA_LAST_SEG); + + /* + * Reset the sg list pointer. + */ + scb->hscb->sgptr = + ahc_htole32(scb->sg_list_phys | SG_FULL_RESID); + + /* + * Copy the first SG into the "current" + * data pointer area. + */ + scb->hscb->dataptr = scb->sg_list->addr; + scb->hscb->datacnt = scb->sg_list->len; + } else { + scb->hscb->sgptr = ahc_htole32(SG_LIST_NULL); + scb->hscb->dataptr = 0; + scb->hscb->datacnt = 0; + scb->sg_count = 0; + } + + LIST_INSERT_HEAD(&ahc->pending_scbs, scb, pending_links); + dev->openings--; + dev->active++; + dev->commands_issued++; + if ((dev->flags & AHC_DEV_PERIODIC_OTAG) != 0) + dev->commands_since_idle_or_otag++; + + scb->flags |= SCB_ACTIVE; + if (untagged_q) { + TAILQ_INSERT_TAIL(untagged_q, scb, links.tqe); + scb->flags |= SCB_UNTAGGEDQ; + } + ahc_queue_scb(ahc, scb); + return 0; +} + +/* + * SCSI controller interrupt handler. + */ +irqreturn_t +ahc_linux_isr(int irq, void *dev_id) +{ + struct ahc_softc *ahc; + u_long flags; + int ours; + + ahc = (struct ahc_softc *) dev_id; + ahc_lock(ahc, &flags); + ours = ahc_intr(ahc); + ahc_unlock(ahc, &flags); + return IRQ_RETVAL(ours); +} + +void +ahc_platform_flushwork(struct ahc_softc *ahc) +{ + +} + +void +ahc_send_async(struct ahc_softc *ahc, char channel, + u_int target, u_int lun, ac_code code) +{ + switch (code) { + case AC_TRANSFER_NEG: + { + struct scsi_target *starget; + struct ahc_initiator_tinfo *tinfo; + struct ahc_tmode_tstate *tstate; + int target_offset; + unsigned int target_ppr_options; + + BUG_ON(target == CAM_TARGET_WILDCARD); + + tinfo = ahc_fetch_transinfo(ahc, channel, + channel == 'A' ? ahc->our_id + : ahc->our_id_b, + target, &tstate); + + /* + * Don't bother reporting results while + * negotiations are still pending. + */ + if (tinfo->curr.period != tinfo->goal.period + || tinfo->curr.width != tinfo->goal.width + || tinfo->curr.offset != tinfo->goal.offset + || tinfo->curr.ppr_options != tinfo->goal.ppr_options) + if (bootverbose == 0) + break; + + /* + * Don't bother reporting results that + * are identical to those last reported. + */ + target_offset = target; + if (channel == 'B') + target_offset += 8; + starget = ahc->platform_data->starget[target_offset]; + if (starget == NULL) + break; + + target_ppr_options = + (spi_dt(starget) ? MSG_EXT_PPR_DT_REQ : 0) + + (spi_qas(starget) ? MSG_EXT_PPR_QAS_REQ : 0) + + (spi_iu(starget) ? MSG_EXT_PPR_IU_REQ : 0); + + if (tinfo->curr.period == spi_period(starget) + && tinfo->curr.width == spi_width(starget) + && tinfo->curr.offset == spi_offset(starget) + && tinfo->curr.ppr_options == target_ppr_options) + if (bootverbose == 0) + break; + + spi_period(starget) = tinfo->curr.period; + spi_width(starget) = tinfo->curr.width; + spi_offset(starget) = tinfo->curr.offset; + spi_dt(starget) = tinfo->curr.ppr_options & MSG_EXT_PPR_DT_REQ ? 1 : 0; + spi_qas(starget) = tinfo->curr.ppr_options & MSG_EXT_PPR_QAS_REQ ? 1 : 0; + spi_iu(starget) = tinfo->curr.ppr_options & MSG_EXT_PPR_IU_REQ ? 1 : 0; + spi_display_xfer_agreement(starget); + break; + } + case AC_SENT_BDR: + { + WARN_ON(lun != CAM_LUN_WILDCARD); + scsi_report_device_reset(ahc->platform_data->host, + channel - 'A', target); + break; + } + case AC_BUS_RESET: + if (ahc->platform_data->host != NULL) { + scsi_report_bus_reset(ahc->platform_data->host, + channel - 'A'); + } + break; + default: + panic("ahc_send_async: Unexpected async event"); + } +} + +/* + * Calls the higher level scsi done function and frees the scb. + */ +void +ahc_done(struct ahc_softc *ahc, struct scb *scb) +{ + struct scsi_cmnd *cmd; + struct ahc_linux_device *dev; + + LIST_REMOVE(scb, pending_links); + if ((scb->flags & SCB_UNTAGGEDQ) != 0) { + struct scb_tailq *untagged_q; + int target_offset; + + target_offset = SCB_GET_TARGET_OFFSET(ahc, scb); + untagged_q = &(ahc->untagged_queues[target_offset]); + TAILQ_REMOVE(untagged_q, scb, links.tqe); + BUG_ON(!TAILQ_EMPTY(untagged_q)); + } else if ((scb->flags & SCB_ACTIVE) == 0) { + /* + * Transactions aborted from the untagged queue may + * not have been dispatched to the controller, so + * only check the SCB_ACTIVE flag for tagged transactions. + */ + printk("SCB %d done'd twice\n", scb->hscb->tag); + ahc_dump_card_state(ahc); + panic("Stopping for safety"); + } + cmd = scb->io_ctx; + dev = scb->platform_data->dev; + dev->active--; + dev->openings++; + if ((cmd->result & (CAM_DEV_QFRZN << 16)) != 0) { + cmd->result &= ~(CAM_DEV_QFRZN << 16); + dev->qfrozen--; + } + ahc_linux_unmap_scb(ahc, scb); + + /* + * Guard against stale sense data. + * The Linux mid-layer assumes that sense + * was retrieved anytime the first byte of + * the sense buffer looks "sane". + */ + cmd->sense_buffer[0] = 0; + if (ahc_get_transaction_status(scb) == CAM_REQ_INPROG) { +#ifdef AHC_REPORT_UNDERFLOWS + uint32_t amount_xferred; + + amount_xferred = + ahc_get_transfer_length(scb) - ahc_get_residual(scb); +#endif + if ((scb->flags & SCB_TRANSMISSION_ERROR) != 0) { +#ifdef AHC_DEBUG + if ((ahc_debug & AHC_SHOW_MISC) != 0) { + ahc_print_path(ahc, scb); + printk("Set CAM_UNCOR_PARITY\n"); + } +#endif + ahc_set_transaction_status(scb, CAM_UNCOR_PARITY); +#ifdef AHC_REPORT_UNDERFLOWS + /* + * This code is disabled by default as some + * clients of the SCSI system do not properly + * initialize the underflow parameter. This + * results in spurious termination of commands + * that complete as expected (e.g. underflow is + * allowed as command can return variable amounts + * of data. + */ + } else if (amount_xferred < scb->io_ctx->underflow) { + u_int i; + + ahc_print_path(ahc, scb); + printk("CDB:"); + for (i = 0; i < scb->io_ctx->cmd_len; i++) + printk(" 0x%x", scb->io_ctx->cmnd[i]); + printk("\n"); + ahc_print_path(ahc, scb); + printk("Saw underflow (%ld of %ld bytes). " + "Treated as error\n", + ahc_get_residual(scb), + ahc_get_transfer_length(scb)); + ahc_set_transaction_status(scb, CAM_DATA_RUN_ERR); +#endif + } else { + ahc_set_transaction_status(scb, CAM_REQ_CMP); + } + } else if (ahc_get_transaction_status(scb) == CAM_SCSI_STATUS_ERROR) { + ahc_linux_handle_scsi_status(ahc, cmd->device, scb); + } + + if (dev->openings == 1 + && ahc_get_transaction_status(scb) == CAM_REQ_CMP + && ahc_get_scsi_status(scb) != SCSI_STATUS_QUEUE_FULL) + dev->tag_success_count++; + /* + * Some devices deal with temporary internal resource + * shortages by returning queue full. When the queue + * full occurrs, we throttle back. Slowly try to get + * back to our previous queue depth. + */ + if ((dev->openings + dev->active) < dev->maxtags + && dev->tag_success_count > AHC_TAG_SUCCESS_INTERVAL) { + dev->tag_success_count = 0; + dev->openings++; + } + + if (dev->active == 0) + dev->commands_since_idle_or_otag = 0; + + if ((scb->flags & SCB_RECOVERY_SCB) != 0) { + printk("Recovery SCB completes\n"); + if (ahc_get_transaction_status(scb) == CAM_BDR_SENT + || ahc_get_transaction_status(scb) == CAM_REQ_ABORTED) + ahc_set_transaction_status(scb, CAM_CMD_TIMEOUT); + + if (ahc->platform_data->eh_done) + complete(ahc->platform_data->eh_done); + } + + ahc_free_scb(ahc, scb); + ahc_linux_queue_cmd_complete(ahc, cmd); +} + +static void +ahc_linux_handle_scsi_status(struct ahc_softc *ahc, + struct scsi_device *sdev, struct scb *scb) +{ + struct ahc_devinfo devinfo; + struct ahc_linux_device *dev = scsi_transport_device_data(sdev); + + ahc_compile_devinfo(&devinfo, + ahc->our_id, + sdev->sdev_target->id, sdev->lun, + sdev->sdev_target->channel == 0 ? 'A' : 'B', + ROLE_INITIATOR); + + /* + * We don't currently trust the mid-layer to + * properly deal with queue full or busy. So, + * when one occurs, we tell the mid-layer to + * unconditionally requeue the command to us + * so that we can retry it ourselves. We also + * implement our own throttling mechanism so + * we don't clobber the device with too many + * commands. + */ + switch (ahc_get_scsi_status(scb)) { + default: + break; + case SCSI_STATUS_CHECK_COND: + case SCSI_STATUS_CMD_TERMINATED: + { + struct scsi_cmnd *cmd; + + /* + * Copy sense information to the OS's cmd + * structure if it is available. + */ + cmd = scb->io_ctx; + if (scb->flags & SCB_SENSE) { + u_int sense_size; + + sense_size = min(sizeof(struct scsi_sense_data) + - ahc_get_sense_residual(scb), + (u_long)SCSI_SENSE_BUFFERSIZE); + memcpy(cmd->sense_buffer, + ahc_get_sense_buf(ahc, scb), sense_size); + if (sense_size < SCSI_SENSE_BUFFERSIZE) + memset(&cmd->sense_buffer[sense_size], 0, + SCSI_SENSE_BUFFERSIZE - sense_size); + cmd->result |= (DRIVER_SENSE << 24); +#ifdef AHC_DEBUG + if (ahc_debug & AHC_SHOW_SENSE) { + int i; + + printk("Copied %d bytes of sense data:", + sense_size); + for (i = 0; i < sense_size; i++) { + if ((i & 0xF) == 0) + printk("\n"); + printk("0x%x ", cmd->sense_buffer[i]); + } + printk("\n"); + } +#endif + } + break; + } + case SCSI_STATUS_QUEUE_FULL: + { + /* + * By the time the core driver has returned this + * command, all other commands that were queued + * to us but not the device have been returned. + * This ensures that dev->active is equal to + * the number of commands actually queued to + * the device. + */ + dev->tag_success_count = 0; + if (dev->active != 0) { + /* + * Drop our opening count to the number + * of commands currently outstanding. + */ + dev->openings = 0; +/* + ahc_print_path(ahc, scb); + printk("Dropping tag count to %d\n", dev->active); + */ + if (dev->active == dev->tags_on_last_queuefull) { + + dev->last_queuefull_same_count++; + /* + * If we repeatedly see a queue full + * at the same queue depth, this + * device has a fixed number of tag + * slots. Lock in this tag depth + * so we stop seeing queue fulls from + * this device. + */ + if (dev->last_queuefull_same_count + == AHC_LOCK_TAGS_COUNT) { + dev->maxtags = dev->active; + ahc_print_path(ahc, scb); + printk("Locking max tag count at %d\n", + dev->active); + } + } else { + dev->tags_on_last_queuefull = dev->active; + dev->last_queuefull_same_count = 0; + } + ahc_set_transaction_status(scb, CAM_REQUEUE_REQ); + ahc_set_scsi_status(scb, SCSI_STATUS_OK); + ahc_platform_set_tags(ahc, sdev, &devinfo, + (dev->flags & AHC_DEV_Q_BASIC) + ? AHC_QUEUE_BASIC : AHC_QUEUE_TAGGED); + break; + } + /* + * Drop down to a single opening, and treat this + * as if the target returned BUSY SCSI status. + */ + dev->openings = 1; + ahc_set_scsi_status(scb, SCSI_STATUS_BUSY); + ahc_platform_set_tags(ahc, sdev, &devinfo, + (dev->flags & AHC_DEV_Q_BASIC) + ? AHC_QUEUE_BASIC : AHC_QUEUE_TAGGED); + break; + } + } +} + +static void +ahc_linux_queue_cmd_complete(struct ahc_softc *ahc, struct scsi_cmnd *cmd) +{ + /* + * Map CAM error codes into Linux Error codes. We + * avoid the conversion so that the DV code has the + * full error information available when making + * state change decisions. + */ + { + u_int new_status; + + switch (ahc_cmd_get_transaction_status(cmd)) { + case CAM_REQ_INPROG: + case CAM_REQ_CMP: + case CAM_SCSI_STATUS_ERROR: + new_status = DID_OK; + break; + case CAM_REQ_ABORTED: + new_status = DID_ABORT; + break; + case CAM_BUSY: + new_status = DID_BUS_BUSY; + break; + case CAM_REQ_INVALID: + case CAM_PATH_INVALID: + new_status = DID_BAD_TARGET; + break; + case CAM_SEL_TIMEOUT: + new_status = DID_NO_CONNECT; + break; + case CAM_SCSI_BUS_RESET: + case CAM_BDR_SENT: + new_status = DID_RESET; + break; + case CAM_UNCOR_PARITY: + new_status = DID_PARITY; + break; + case CAM_CMD_TIMEOUT: + new_status = DID_TIME_OUT; + break; + case CAM_UA_ABORT: + case CAM_REQ_CMP_ERR: + case CAM_AUTOSENSE_FAIL: + case CAM_NO_HBA: + case CAM_DATA_RUN_ERR: + case CAM_UNEXP_BUSFREE: + case CAM_SEQUENCE_FAIL: + case CAM_CCB_LEN_ERR: + case CAM_PROVIDE_FAIL: + case CAM_REQ_TERMIO: + case CAM_UNREC_HBA_ERROR: + case CAM_REQ_TOO_BIG: + new_status = DID_ERROR; + break; + case CAM_REQUEUE_REQ: + new_status = DID_REQUEUE; + break; + default: + /* We should never get here */ + new_status = DID_ERROR; + break; + } + + ahc_cmd_set_transaction_status(cmd, new_status); + } + + cmd->scsi_done(cmd); +} + +static void +ahc_linux_freeze_simq(struct ahc_softc *ahc) +{ + unsigned long s; + + ahc_lock(ahc, &s); + ahc->platform_data->qfrozen++; + if (ahc->platform_data->qfrozen == 1) { + scsi_block_requests(ahc->platform_data->host); + + /* XXX What about Twin channels? */ + ahc_platform_abort_scbs(ahc, CAM_TARGET_WILDCARD, ALL_CHANNELS, + CAM_LUN_WILDCARD, SCB_LIST_NULL, + ROLE_INITIATOR, CAM_REQUEUE_REQ); + } + ahc_unlock(ahc, &s); +} + +static void +ahc_linux_release_simq(struct ahc_softc *ahc) +{ + u_long s; + int unblock_reqs; + + unblock_reqs = 0; + ahc_lock(ahc, &s); + if (ahc->platform_data->qfrozen > 0) + ahc->platform_data->qfrozen--; + if (ahc->platform_data->qfrozen == 0) + unblock_reqs = 1; + ahc_unlock(ahc, &s); + /* + * There is still a race here. The mid-layer + * should keep its own freeze count and use + * a bottom half handler to run the queues + * so we can unblock with our own lock held. + */ + if (unblock_reqs) + scsi_unblock_requests(ahc->platform_data->host); +} + +static int +ahc_linux_queue_recovery_cmd(struct scsi_cmnd *cmd, scb_flag flag) +{ + struct ahc_softc *ahc; + struct ahc_linux_device *dev; + struct scb *pending_scb; + u_int saved_scbptr; + u_int active_scb_index; + u_int last_phase; + u_int saved_scsiid; + u_int cdb_byte; + int retval; + int was_paused; + int paused; + int wait; + int disconnected; + unsigned long flags; + + pending_scb = NULL; + paused = FALSE; + wait = FALSE; + ahc = *(struct ahc_softc **)cmd->device->host->hostdata; + + scmd_printk(KERN_INFO, cmd, "Attempting to queue a%s message\n", + flag == SCB_ABORT ? "n ABORT" : " TARGET RESET"); + + printk("CDB:"); + for (cdb_byte = 0; cdb_byte < cmd->cmd_len; cdb_byte++) + printk(" 0x%x", cmd->cmnd[cdb_byte]); + printk("\n"); + + ahc_lock(ahc, &flags); + + /* + * First determine if we currently own this command. + * Start by searching the device queue. If not found + * there, check the pending_scb list. If not found + * at all, and the system wanted us to just abort the + * command, return success. + */ + dev = scsi_transport_device_data(cmd->device); + + if (dev == NULL) { + /* + * No target device for this command exists, + * so we must not still own the command. + */ + printk("%s:%d:%d:%d: Is not an active device\n", + ahc_name(ahc), cmd->device->channel, cmd->device->id, + (u8)cmd->device->lun); + retval = SUCCESS; + goto no_cmd; + } + + if ((dev->flags & (AHC_DEV_Q_BASIC|AHC_DEV_Q_TAGGED)) == 0 + && ahc_search_untagged_queues(ahc, cmd, cmd->device->id, + cmd->device->channel + 'A', + (u8)cmd->device->lun, + CAM_REQ_ABORTED, SEARCH_COMPLETE) != 0) { + printk("%s:%d:%d:%d: Command found on untagged queue\n", + ahc_name(ahc), cmd->device->channel, cmd->device->id, + (u8)cmd->device->lun); + retval = SUCCESS; + goto done; + } + + /* + * See if we can find a matching cmd in the pending list. + */ + LIST_FOREACH(pending_scb, &ahc->pending_scbs, pending_links) { + if (pending_scb->io_ctx == cmd) + break; + } + + if (pending_scb == NULL && flag == SCB_DEVICE_RESET) { + + /* Any SCB for this device will do for a target reset */ + LIST_FOREACH(pending_scb, &ahc->pending_scbs, pending_links) { + if (ahc_match_scb(ahc, pending_scb, scmd_id(cmd), + scmd_channel(cmd) + 'A', + CAM_LUN_WILDCARD, + SCB_LIST_NULL, ROLE_INITIATOR)) + break; + } + } + + if (pending_scb == NULL) { + scmd_printk(KERN_INFO, cmd, "Command not found\n"); + goto no_cmd; + } + + if ((pending_scb->flags & SCB_RECOVERY_SCB) != 0) { + /* + * We can't queue two recovery actions using the same SCB + */ + retval = FAILED; + goto done; + } + + /* + * Ensure that the card doesn't do anything + * behind our back and that we didn't "just" miss + * an interrupt that would affect this cmd. + */ + was_paused = ahc_is_paused(ahc); + ahc_pause_and_flushwork(ahc); + paused = TRUE; + + if ((pending_scb->flags & SCB_ACTIVE) == 0) { + scmd_printk(KERN_INFO, cmd, "Command already completed\n"); + goto no_cmd; + } + + printk("%s: At time of recovery, card was %spaused\n", + ahc_name(ahc), was_paused ? "" : "not "); + ahc_dump_card_state(ahc); + + disconnected = TRUE; + if (flag == SCB_ABORT) { + if (ahc_search_qinfifo(ahc, cmd->device->id, + cmd->device->channel + 'A', + cmd->device->lun, + pending_scb->hscb->tag, + ROLE_INITIATOR, CAM_REQ_ABORTED, + SEARCH_COMPLETE) > 0) { + printk("%s:%d:%d:%d: Cmd aborted from QINFIFO\n", + ahc_name(ahc), cmd->device->channel, + cmd->device->id, (u8)cmd->device->lun); + retval = SUCCESS; + goto done; + } + } else if (ahc_search_qinfifo(ahc, cmd->device->id, + cmd->device->channel + 'A', + cmd->device->lun, + pending_scb->hscb->tag, + ROLE_INITIATOR, /*status*/0, + SEARCH_COUNT) > 0) { + disconnected = FALSE; + } + + if (disconnected && (ahc_inb(ahc, SEQ_FLAGS) & NOT_IDENTIFIED) == 0) { + struct scb *bus_scb; + + bus_scb = ahc_lookup_scb(ahc, ahc_inb(ahc, SCB_TAG)); + if (bus_scb == pending_scb) + disconnected = FALSE; + else if (flag != SCB_ABORT + && ahc_inb(ahc, SAVED_SCSIID) == pending_scb->hscb->scsiid + && ahc_inb(ahc, SAVED_LUN) == SCB_GET_LUN(pending_scb)) + disconnected = FALSE; + } + + /* + * At this point, pending_scb is the scb associated with the + * passed in command. That command is currently active on the + * bus, is in the disconnected state, or we're hoping to find + * a command for the same target active on the bus to abuse to + * send a BDR. Queue the appropriate message based on which of + * these states we are in. + */ + last_phase = ahc_inb(ahc, LASTPHASE); + saved_scbptr = ahc_inb(ahc, SCBPTR); + active_scb_index = ahc_inb(ahc, SCB_TAG); + saved_scsiid = ahc_inb(ahc, SAVED_SCSIID); + if (last_phase != P_BUSFREE + && (pending_scb->hscb->tag == active_scb_index + || (flag == SCB_DEVICE_RESET + && SCSIID_TARGET(ahc, saved_scsiid) == scmd_id(cmd)))) { + + /* + * We're active on the bus, so assert ATN + * and hope that the target responds. + */ + pending_scb = ahc_lookup_scb(ahc, active_scb_index); + pending_scb->flags |= SCB_RECOVERY_SCB|flag; + ahc_outb(ahc, MSG_OUT, HOST_MSG); + ahc_outb(ahc, SCSISIGO, last_phase|ATNO); + scmd_printk(KERN_INFO, cmd, "Device is active, asserting ATN\n"); + wait = TRUE; + } else if (disconnected) { + + /* + * Actually re-queue this SCB in an attempt + * to select the device before it reconnects. + * In either case (selection or reselection), + * we will now issue the approprate message + * to the timed-out device. + * + * Set the MK_MESSAGE control bit indicating + * that we desire to send a message. We + * also set the disconnected flag since + * in the paging case there is no guarantee + * that our SCB control byte matches the + * version on the card. We don't want the + * sequencer to abort the command thinking + * an unsolicited reselection occurred. + */ + pending_scb->hscb->control |= MK_MESSAGE|DISCONNECTED; + pending_scb->flags |= SCB_RECOVERY_SCB|flag; + + /* + * Remove any cached copy of this SCB in the + * disconnected list in preparation for the + * queuing of our abort SCB. We use the + * same element in the SCB, SCB_NEXT, for + * both the qinfifo and the disconnected list. + */ + ahc_search_disc_list(ahc, cmd->device->id, + cmd->device->channel + 'A', + cmd->device->lun, pending_scb->hscb->tag, + /*stop_on_first*/TRUE, + /*remove*/TRUE, + /*save_state*/FALSE); + + /* + * In the non-paging case, the sequencer will + * never re-reference the in-core SCB. + * To make sure we are notified during + * reselection, set the MK_MESSAGE flag in + * the card's copy of the SCB. + */ + if ((ahc->flags & AHC_PAGESCBS) == 0) { + ahc_outb(ahc, SCBPTR, pending_scb->hscb->tag); + ahc_outb(ahc, SCB_CONTROL, + ahc_inb(ahc, SCB_CONTROL)|MK_MESSAGE); + } + + /* + * Clear out any entries in the QINFIFO first + * so we are the next SCB for this target + * to run. + */ + ahc_search_qinfifo(ahc, cmd->device->id, + cmd->device->channel + 'A', + cmd->device->lun, SCB_LIST_NULL, + ROLE_INITIATOR, CAM_REQUEUE_REQ, + SEARCH_COMPLETE); + ahc_qinfifo_requeue_tail(ahc, pending_scb); + ahc_outb(ahc, SCBPTR, saved_scbptr); + ahc_print_path(ahc, pending_scb); + printk("Device is disconnected, re-queuing SCB\n"); + wait = TRUE; + } else { + scmd_printk(KERN_INFO, cmd, "Unable to deliver message\n"); + retval = FAILED; + goto done; + } + +no_cmd: + /* + * Our assumption is that if we don't have the command, no + * recovery action was required, so we return success. Again, + * the semantics of the mid-layer recovery engine are not + * well defined, so this may change in time. + */ + retval = SUCCESS; +done: + if (paused) + ahc_unpause(ahc); + if (wait) { + DECLARE_COMPLETION_ONSTACK(done); + + ahc->platform_data->eh_done = &done; + ahc_unlock(ahc, &flags); + + printk("Recovery code sleeping\n"); + if (!wait_for_completion_timeout(&done, 5 * HZ)) { + ahc_lock(ahc, &flags); + ahc->platform_data->eh_done = NULL; + ahc_unlock(ahc, &flags); + + printk("Timer Expired\n"); + retval = FAILED; + } + printk("Recovery code awake\n"); + } else + ahc_unlock(ahc, &flags); + return (retval); +} + +static void ahc_linux_set_width(struct scsi_target *starget, int width) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahc_softc *ahc = *((struct ahc_softc **)shost->hostdata); + struct ahc_devinfo devinfo; + unsigned long flags; + + ahc_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + ahc_lock(ahc, &flags); + ahc_set_width(ahc, &devinfo, width, AHC_TRANS_GOAL, FALSE); + ahc_unlock(ahc, &flags); +} + +static void ahc_linux_set_period(struct scsi_target *starget, int period) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahc_softc *ahc = *((struct ahc_softc **)shost->hostdata); + struct ahc_tmode_tstate *tstate; + struct ahc_initiator_tinfo *tinfo + = ahc_fetch_transinfo(ahc, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahc_devinfo devinfo; + unsigned int ppr_options = tinfo->goal.ppr_options; + unsigned long flags; + unsigned long offset = tinfo->goal.offset; + const struct ahc_syncrate *syncrate; + + if (offset == 0) + offset = MAX_OFFSET; + + if (period < 9) + period = 9; /* 12.5ns is our minimum */ + if (period == 9) { + if (spi_max_width(starget)) + ppr_options |= MSG_EXT_PPR_DT_REQ; + else + /* need wide for DT and need DT for 12.5 ns */ + period = 10; + } + + ahc_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + + /* all PPR requests apart from QAS require wide transfers */ + if (ppr_options & ~MSG_EXT_PPR_QAS_REQ) { + if (spi_width(starget) == 0) + ppr_options &= MSG_EXT_PPR_QAS_REQ; + } + + syncrate = ahc_find_syncrate(ahc, &period, &ppr_options, AHC_SYNCRATE_DT); + ahc_lock(ahc, &flags); + ahc_set_syncrate(ahc, &devinfo, syncrate, period, offset, + ppr_options, AHC_TRANS_GOAL, FALSE); + ahc_unlock(ahc, &flags); +} + +static void ahc_linux_set_offset(struct scsi_target *starget, int offset) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahc_softc *ahc = *((struct ahc_softc **)shost->hostdata); + struct ahc_tmode_tstate *tstate; + struct ahc_initiator_tinfo *tinfo + = ahc_fetch_transinfo(ahc, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahc_devinfo devinfo; + unsigned int ppr_options = 0; + unsigned int period = 0; + unsigned long flags; + const struct ahc_syncrate *syncrate = NULL; + + ahc_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + if (offset != 0) { + syncrate = ahc_find_syncrate(ahc, &period, &ppr_options, AHC_SYNCRATE_DT); + period = tinfo->goal.period; + ppr_options = tinfo->goal.ppr_options; + } + ahc_lock(ahc, &flags); + ahc_set_syncrate(ahc, &devinfo, syncrate, period, offset, + ppr_options, AHC_TRANS_GOAL, FALSE); + ahc_unlock(ahc, &flags); +} + +static void ahc_linux_set_dt(struct scsi_target *starget, int dt) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahc_softc *ahc = *((struct ahc_softc **)shost->hostdata); + struct ahc_tmode_tstate *tstate; + struct ahc_initiator_tinfo *tinfo + = ahc_fetch_transinfo(ahc, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahc_devinfo devinfo; + unsigned int ppr_options = tinfo->goal.ppr_options + & ~MSG_EXT_PPR_DT_REQ; + unsigned int period = tinfo->goal.period; + unsigned int width = tinfo->goal.width; + unsigned long flags; + const struct ahc_syncrate *syncrate; + + if (dt && spi_max_width(starget)) { + ppr_options |= MSG_EXT_PPR_DT_REQ; + if (!width) + ahc_linux_set_width(starget, 1); + } else if (period == 9) + period = 10; /* if resetting DT, period must be >= 25ns */ + + ahc_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + syncrate = ahc_find_syncrate(ahc, &period, &ppr_options,AHC_SYNCRATE_DT); + ahc_lock(ahc, &flags); + ahc_set_syncrate(ahc, &devinfo, syncrate, period, tinfo->goal.offset, + ppr_options, AHC_TRANS_GOAL, FALSE); + ahc_unlock(ahc, &flags); +} + +#if 0 +/* FIXME: This code claims to support IU and QAS. However, the actual + * sequencer code and aic7xxx_core have no support for these parameters and + * will get into a bad state if they're negotiated. Do not enable this + * unless you know what you're doing */ +static void ahc_linux_set_qas(struct scsi_target *starget, int qas) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahc_softc *ahc = *((struct ahc_softc **)shost->hostdata); + struct ahc_tmode_tstate *tstate; + struct ahc_initiator_tinfo *tinfo + = ahc_fetch_transinfo(ahc, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahc_devinfo devinfo; + unsigned int ppr_options = tinfo->goal.ppr_options + & ~MSG_EXT_PPR_QAS_REQ; + unsigned int period = tinfo->goal.period; + unsigned long flags; + struct ahc_syncrate *syncrate; + + if (qas) + ppr_options |= MSG_EXT_PPR_QAS_REQ; + + ahc_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + syncrate = ahc_find_syncrate(ahc, &period, &ppr_options, AHC_SYNCRATE_DT); + ahc_lock(ahc, &flags); + ahc_set_syncrate(ahc, &devinfo, syncrate, period, tinfo->goal.offset, + ppr_options, AHC_TRANS_GOAL, FALSE); + ahc_unlock(ahc, &flags); +} + +static void ahc_linux_set_iu(struct scsi_target *starget, int iu) +{ + struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); + struct ahc_softc *ahc = *((struct ahc_softc **)shost->hostdata); + struct ahc_tmode_tstate *tstate; + struct ahc_initiator_tinfo *tinfo + = ahc_fetch_transinfo(ahc, + starget->channel + 'A', + shost->this_id, starget->id, &tstate); + struct ahc_devinfo devinfo; + unsigned int ppr_options = tinfo->goal.ppr_options + & ~MSG_EXT_PPR_IU_REQ; + unsigned int period = tinfo->goal.period; + unsigned long flags; + struct ahc_syncrate *syncrate; + + if (iu) + ppr_options |= MSG_EXT_PPR_IU_REQ; + + ahc_compile_devinfo(&devinfo, shost->this_id, starget->id, 0, + starget->channel + 'A', ROLE_INITIATOR); + syncrate = ahc_find_syncrate(ahc, &period, &ppr_options, AHC_SYNCRATE_DT); + ahc_lock(ahc, &flags); + ahc_set_syncrate(ahc, &devinfo, syncrate, period, tinfo->goal.offset, + ppr_options, AHC_TRANS_GOAL, FALSE); + ahc_unlock(ahc, &flags); +} +#endif + +static void ahc_linux_get_signalling(struct Scsi_Host *shost) +{ + struct ahc_softc *ahc = *(struct ahc_softc **)shost->hostdata; + unsigned long flags; + u8 mode; + + if (!(ahc->features & AHC_ULTRA2)) { + /* non-LVD chipset, may not have SBLKCTL reg */ + spi_signalling(shost) = + ahc->features & AHC_HVD ? + SPI_SIGNAL_HVD : + SPI_SIGNAL_SE; + return; + } + + ahc_lock(ahc, &flags); + ahc_pause(ahc); + mode = ahc_inb(ahc, SBLKCTL); + ahc_unpause(ahc); + ahc_unlock(ahc, &flags); + + if (mode & ENAB40) + spi_signalling(shost) = SPI_SIGNAL_LVD; + else if (mode & ENAB20) + spi_signalling(shost) = SPI_SIGNAL_SE; + else + spi_signalling(shost) = SPI_SIGNAL_UNKNOWN; +} + +static struct spi_function_template ahc_linux_transport_functions = { + .set_offset = ahc_linux_set_offset, + .show_offset = 1, + .set_period = ahc_linux_set_period, + .show_period = 1, + .set_width = ahc_linux_set_width, + .show_width = 1, + .set_dt = ahc_linux_set_dt, + .show_dt = 1, +#if 0 + .set_iu = ahc_linux_set_iu, + .show_iu = 1, + .set_qas = ahc_linux_set_qas, + .show_qas = 1, +#endif + .get_signalling = ahc_linux_get_signalling, +}; + + + +static int __init +ahc_linux_init(void) +{ + /* + * If we've been passed any parameters, process them now. + */ + if (aic7xxx) + aic7xxx_setup(aic7xxx); + + ahc_linux_transport_template = + spi_attach_transport(&ahc_linux_transport_functions); + if (!ahc_linux_transport_template) + return -ENODEV; + + scsi_transport_reserve_device(ahc_linux_transport_template, + sizeof(struct ahc_linux_device)); + + ahc_linux_pci_init(); + ahc_linux_eisa_init(); + return 0; +} + +static void +ahc_linux_exit(void) +{ + ahc_linux_pci_exit(); + ahc_linux_eisa_exit(); + spi_release_transport(ahc_linux_transport_template); +} + +module_init(ahc_linux_init); +module_exit(ahc_linux_exit); diff --git a/drivers/scsi/aic7xxx/aic7xxx_osm.h b/drivers/scsi/aic7xxx/aic7xxx_osm.h new file mode 100644 index 000000000..f8489078f --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx_osm.h @@ -0,0 +1,699 @@ +/* + * Adaptec AIC7xxx device driver for Linux. + * + * Copyright (c) 1994 John Aycock + * The University of Calgary Department of Computer Science. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * Copyright (c) 2000-2003 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic7xxx_osm.h#151 $ + * + */ +#ifndef _AIC7XXX_LINUX_H_ +#define _AIC7XXX_LINUX_H_ + +#include <linux/types.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/ioport.h> +#include <linux/pci.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <asm/byteorder.h> +#include <asm/io.h> + +#include <scsi/scsi.h> +#include <scsi/scsi_cmnd.h> +#include <scsi/scsi_eh.h> +#include <scsi/scsi_device.h> +#include <scsi/scsi_host.h> +#include <scsi/scsi_tcq.h> +#include <scsi/scsi_transport.h> +#include <scsi/scsi_transport_spi.h> + +/* Core SCSI definitions */ +#define AIC_LIB_PREFIX ahc + +#include "cam.h" +#include "queue.h" +#include "scsi_message.h" +#include "aiclib.h" + +/*********************************** Debugging ********************************/ +#ifdef CONFIG_AIC7XXX_DEBUG_ENABLE +#ifdef CONFIG_AIC7XXX_DEBUG_MASK +#define AHC_DEBUG 1 +#define AHC_DEBUG_OPTS CONFIG_AIC7XXX_DEBUG_MASK +#else +/* + * Compile in debugging code, but do not enable any printfs. + */ +#define AHC_DEBUG 1 +#endif +/* No debugging code. */ +#endif + +/************************* Forward Declarations *******************************/ +struct ahc_softc; +typedef struct pci_dev *ahc_dev_softc_t; +typedef struct scsi_cmnd *ahc_io_ctx_t; + +/******************************* Byte Order ***********************************/ +#define ahc_htobe16(x) cpu_to_be16(x) +#define ahc_htobe32(x) cpu_to_be32(x) +#define ahc_htobe64(x) cpu_to_be64(x) +#define ahc_htole16(x) cpu_to_le16(x) +#define ahc_htole32(x) cpu_to_le32(x) +#define ahc_htole64(x) cpu_to_le64(x) + +#define ahc_be16toh(x) be16_to_cpu(x) +#define ahc_be32toh(x) be32_to_cpu(x) +#define ahc_be64toh(x) be64_to_cpu(x) +#define ahc_le16toh(x) le16_to_cpu(x) +#define ahc_le32toh(x) le32_to_cpu(x) +#define ahc_le64toh(x) le64_to_cpu(x) + +/************************* Configuration Data *********************************/ +extern u_int aic7xxx_no_probe; +extern u_int aic7xxx_allow_memio; +extern struct scsi_host_template aic7xxx_driver_template; + +/***************************** Bus Space/DMA **********************************/ + +typedef uint32_t bus_size_t; + +typedef enum { + BUS_SPACE_MEMIO, + BUS_SPACE_PIO +} bus_space_tag_t; + +typedef union { + u_long ioport; + volatile uint8_t __iomem *maddr; +} bus_space_handle_t; + +typedef struct bus_dma_segment +{ + dma_addr_t ds_addr; + bus_size_t ds_len; +} bus_dma_segment_t; + +struct ahc_linux_dma_tag +{ + bus_size_t alignment; + bus_size_t boundary; + bus_size_t maxsize; +}; +typedef struct ahc_linux_dma_tag* bus_dma_tag_t; + +typedef dma_addr_t bus_dmamap_t; + +typedef int bus_dma_filter_t(void*, dma_addr_t); +typedef void bus_dmamap_callback_t(void *, bus_dma_segment_t *, int, int); + +#define BUS_DMA_WAITOK 0x0 +#define BUS_DMA_NOWAIT 0x1 +#define BUS_DMA_ALLOCNOW 0x2 +#define BUS_DMA_LOAD_SEGS 0x4 /* + * Argument is an S/G list not + * a single buffer. + */ + +#define BUS_SPACE_MAXADDR 0xFFFFFFFF +#define BUS_SPACE_MAXADDR_32BIT 0xFFFFFFFF +#define BUS_SPACE_MAXSIZE_32BIT 0xFFFFFFFF + +int ahc_dma_tag_create(struct ahc_softc *, bus_dma_tag_t /*parent*/, + bus_size_t /*alignment*/, bus_size_t /*boundary*/, + dma_addr_t /*lowaddr*/, dma_addr_t /*highaddr*/, + bus_dma_filter_t*/*filter*/, void */*filterarg*/, + bus_size_t /*maxsize*/, int /*nsegments*/, + bus_size_t /*maxsegsz*/, int /*flags*/, + bus_dma_tag_t */*dma_tagp*/); + +void ahc_dma_tag_destroy(struct ahc_softc *, bus_dma_tag_t /*tag*/); + +int ahc_dmamem_alloc(struct ahc_softc *, bus_dma_tag_t /*dmat*/, + void** /*vaddr*/, int /*flags*/, + bus_dmamap_t* /*mapp*/); + +void ahc_dmamem_free(struct ahc_softc *, bus_dma_tag_t /*dmat*/, + void* /*vaddr*/, bus_dmamap_t /*map*/); + +void ahc_dmamap_destroy(struct ahc_softc *, bus_dma_tag_t /*tag*/, + bus_dmamap_t /*map*/); + +int ahc_dmamap_load(struct ahc_softc *ahc, bus_dma_tag_t /*dmat*/, + bus_dmamap_t /*map*/, void * /*buf*/, + bus_size_t /*buflen*/, bus_dmamap_callback_t *, + void */*callback_arg*/, int /*flags*/); + +int ahc_dmamap_unload(struct ahc_softc *, bus_dma_tag_t, bus_dmamap_t); + +/* + * Operations performed by ahc_dmamap_sync(). + */ +#define BUS_DMASYNC_PREREAD 0x01 /* pre-read synchronization */ +#define BUS_DMASYNC_POSTREAD 0x02 /* post-read synchronization */ +#define BUS_DMASYNC_PREWRITE 0x04 /* pre-write synchronization */ +#define BUS_DMASYNC_POSTWRITE 0x08 /* post-write synchronization */ + +/* + * XXX + * ahc_dmamap_sync is only used on buffers allocated with + * the pci_alloc_consistent() API. Although I'm not sure how + * this works on architectures with a write buffer, Linux does + * not have an API to sync "coherent" memory. Perhaps we need + * to do an mb()? + */ +#define ahc_dmamap_sync(ahc, dma_tag, dmamap, offset, len, op) + +/********************************** Includes **********************************/ +#ifdef CONFIG_AIC7XXX_REG_PRETTY_PRINT +#define AIC_DEBUG_REGISTERS 1 +#else +#define AIC_DEBUG_REGISTERS 0 +#endif +#include "aic7xxx.h" + +/***************************** Timer Facilities *******************************/ +static inline void +ahc_scb_timer_reset(struct scb *scb, u_int usec) +{ +} + +/***************************** SMP support ************************************/ +#include <linux/spinlock.h> + +#define AIC7XXX_DRIVER_VERSION "7.0" + +/*************************** Device Data Structures ***************************/ +/* + * A per probed device structure used to deal with some error recovery + * scenarios that the Linux mid-layer code just doesn't know how to + * handle. The structure allocated for a device only becomes persistent + * after a successfully completed inquiry command to the target when + * that inquiry data indicates a lun is present. + */ +typedef enum { + AHC_DEV_FREEZE_TIL_EMPTY = 0x02, /* Freeze queue until active == 0 */ + AHC_DEV_Q_BASIC = 0x10, /* Allow basic device queuing */ + AHC_DEV_Q_TAGGED = 0x20, /* Allow full SCSI2 command queueing */ + AHC_DEV_PERIODIC_OTAG = 0x40, /* Send OTAG to prevent starvation */ +} ahc_linux_dev_flags; + +struct ahc_linux_device { + /* + * The number of transactions currently + * queued to the device. + */ + int active; + + /* + * The currently allowed number of + * transactions that can be queued to + * the device. Must be signed for + * conversion from tagged to untagged + * mode where the device may have more + * than one outstanding active transaction. + */ + int openings; + + /* + * A positive count indicates that this + * device's queue is halted. + */ + u_int qfrozen; + + /* + * Cumulative command counter. + */ + u_long commands_issued; + + /* + * The number of tagged transactions when + * running at our current opening level + * that have been successfully received by + * this device since the last QUEUE FULL. + */ + u_int tag_success_count; +#define AHC_TAG_SUCCESS_INTERVAL 50 + + ahc_linux_dev_flags flags; + + /* + * The high limit for the tags variable. + */ + u_int maxtags; + + /* + * The computed number of tags outstanding + * at the time of the last QUEUE FULL event. + */ + u_int tags_on_last_queuefull; + + /* + * How many times we have seen a queue full + * with the same number of tags. This is used + * to stop our adaptive queue depth algorithm + * on devices with a fixed number of tags. + */ + u_int last_queuefull_same_count; +#define AHC_LOCK_TAGS_COUNT 50 + + /* + * How many transactions have been queued + * without the device going idle. We use + * this statistic to determine when to issue + * an ordered tag to prevent transaction + * starvation. This statistic is only updated + * if the AHC_DEV_PERIODIC_OTAG flag is set + * on this device. + */ + u_int commands_since_idle_or_otag; +#define AHC_OTAG_THRESH 500 +}; + +/********************* Definitions Required by the Core ***********************/ +/* + * Number of SG segments we require. So long as the S/G segments for + * a particular transaction are allocated in a physically contiguous + * manner and are allocated below 4GB, the number of S/G segments is + * unrestricted. + */ +#define AHC_NSEG 128 + +/* + * Per-SCB OSM storage. + */ +struct scb_platform_data { + struct ahc_linux_device *dev; + dma_addr_t buf_busaddr; + uint32_t xfer_len; + uint32_t sense_resid; /* Auto-Sense residual */ +}; + +/* + * Define a structure used for each host adapter. All members are + * aligned on a boundary >= the size of the member to honor the + * alignment restrictions of the various platforms supported by + * this driver. + */ +struct ahc_platform_data { + /* + * Fields accessed from interrupt context. + */ + struct scsi_target *starget[AHC_NUM_TARGETS]; + + spinlock_t spin_lock; + u_int qfrozen; + struct completion *eh_done; + struct Scsi_Host *host; /* pointer to scsi host */ +#define AHC_LINUX_NOIRQ ((uint32_t)~0) + uint32_t irq; /* IRQ for this adapter */ + uint32_t bios_address; + resource_size_t mem_busaddr; /* Mem Base Addr */ +}; + +void ahc_delay(long); + + +/***************************** Low Level I/O **********************************/ +uint8_t ahc_inb(struct ahc_softc * ahc, long port); +void ahc_outb(struct ahc_softc * ahc, long port, uint8_t val); +void ahc_outsb(struct ahc_softc * ahc, long port, + uint8_t *, int count); +void ahc_insb(struct ahc_softc * ahc, long port, + uint8_t *, int count); + +/**************************** Initialization **********************************/ +int ahc_linux_register_host(struct ahc_softc *, + struct scsi_host_template *); + +/******************************** Locking *************************************/ +/* Lock protecting internal data structures */ + +static inline void +ahc_lockinit(struct ahc_softc *ahc) +{ + spin_lock_init(&ahc->platform_data->spin_lock); +} + +static inline void +ahc_lock(struct ahc_softc *ahc, unsigned long *flags) +{ + spin_lock_irqsave(&ahc->platform_data->spin_lock, *flags); +} + +static inline void +ahc_unlock(struct ahc_softc *ahc, unsigned long *flags) +{ + spin_unlock_irqrestore(&ahc->platform_data->spin_lock, *flags); +} + +/******************************* PCI Definitions ******************************/ +/* + * PCIM_xxx: mask to locate subfield in register + * PCIR_xxx: config register offset + * PCIC_xxx: device class + * PCIS_xxx: device subclass + * PCIP_xxx: device programming interface + * PCIV_xxx: PCI vendor ID (only required to fixup ancient devices) + * PCID_xxx: device ID + */ +#define PCIR_DEVVENDOR 0x00 +#define PCIR_VENDOR 0x00 +#define PCIR_DEVICE 0x02 +#define PCIR_COMMAND 0x04 +#define PCIM_CMD_PORTEN 0x0001 +#define PCIM_CMD_MEMEN 0x0002 +#define PCIM_CMD_BUSMASTEREN 0x0004 +#define PCIM_CMD_MWRICEN 0x0010 +#define PCIM_CMD_PERRESPEN 0x0040 +#define PCIM_CMD_SERRESPEN 0x0100 +#define PCIR_STATUS 0x06 +#define PCIR_REVID 0x08 +#define PCIR_PROGIF 0x09 +#define PCIR_SUBCLASS 0x0a +#define PCIR_CLASS 0x0b +#define PCIR_CACHELNSZ 0x0c +#define PCIR_LATTIMER 0x0d +#define PCIR_HEADERTYPE 0x0e +#define PCIM_MFDEV 0x80 +#define PCIR_BIST 0x0f +#define PCIR_CAP_PTR 0x34 + +/* config registers for header type 0 devices */ +#define PCIR_MAPS 0x10 +#define PCIR_SUBVEND_0 0x2c +#define PCIR_SUBDEV_0 0x2e + +typedef enum +{ + AHC_POWER_STATE_D0, + AHC_POWER_STATE_D1, + AHC_POWER_STATE_D2, + AHC_POWER_STATE_D3 +} ahc_power_state; + +/**************************** VL/EISA Routines ********************************/ +#ifdef CONFIG_EISA +int ahc_linux_eisa_init(void); +void ahc_linux_eisa_exit(void); +int aic7770_map_registers(struct ahc_softc *ahc, + u_int port); +int aic7770_map_int(struct ahc_softc *ahc, u_int irq); +#else +static inline int ahc_linux_eisa_init(void) { + return -ENODEV; +} +static inline void ahc_linux_eisa_exit(void) { +} +#endif + +/******************************* PCI Routines *********************************/ +#ifdef CONFIG_PCI +int ahc_linux_pci_init(void); +void ahc_linux_pci_exit(void); +int ahc_pci_map_registers(struct ahc_softc *ahc); +int ahc_pci_map_int(struct ahc_softc *ahc); + +uint32_t ahc_pci_read_config(ahc_dev_softc_t pci, + int reg, int width); + +void ahc_pci_write_config(ahc_dev_softc_t pci, + int reg, uint32_t value, + int width); + +static inline int ahc_get_pci_function(ahc_dev_softc_t); +static inline int +ahc_get_pci_function(ahc_dev_softc_t pci) +{ + return (PCI_FUNC(pci->devfn)); +} + +static inline int ahc_get_pci_slot(ahc_dev_softc_t); +static inline int +ahc_get_pci_slot(ahc_dev_softc_t pci) +{ + return (PCI_SLOT(pci->devfn)); +} + +static inline int ahc_get_pci_bus(ahc_dev_softc_t); +static inline int +ahc_get_pci_bus(ahc_dev_softc_t pci) +{ + return (pci->bus->number); +} +#else +static inline int ahc_linux_pci_init(void) { + return 0; +} +static inline void ahc_linux_pci_exit(void) { +} +#endif + +static inline void ahc_flush_device_writes(struct ahc_softc *); +static inline void +ahc_flush_device_writes(struct ahc_softc *ahc) +{ + /* XXX Is this sufficient for all architectures??? */ + ahc_inb(ahc, INTSTAT); +} + +/**************************** Proc FS Support *********************************/ +int ahc_proc_write_seeprom(struct Scsi_Host *, char *, int); +int ahc_linux_show_info(struct seq_file *, struct Scsi_Host *); + +/*************************** Domain Validation ********************************/ +/*********************** Transaction Access Wrappers *************************/ +static inline void ahc_cmd_set_transaction_status(struct scsi_cmnd *, uint32_t); +static inline void ahc_set_transaction_status(struct scb *, uint32_t); +static inline void ahc_cmd_set_scsi_status(struct scsi_cmnd *, uint32_t); +static inline void ahc_set_scsi_status(struct scb *, uint32_t); +static inline uint32_t ahc_cmd_get_transaction_status(struct scsi_cmnd *cmd); +static inline uint32_t ahc_get_transaction_status(struct scb *); +static inline uint32_t ahc_cmd_get_scsi_status(struct scsi_cmnd *cmd); +static inline uint32_t ahc_get_scsi_status(struct scb *); +static inline void ahc_set_transaction_tag(struct scb *, int, u_int); +static inline u_long ahc_get_transfer_length(struct scb *); +static inline int ahc_get_transfer_dir(struct scb *); +static inline void ahc_set_residual(struct scb *, u_long); +static inline void ahc_set_sense_residual(struct scb *scb, u_long resid); +static inline u_long ahc_get_residual(struct scb *); +static inline u_long ahc_get_sense_residual(struct scb *); +static inline int ahc_perform_autosense(struct scb *); +static inline uint32_t ahc_get_sense_bufsize(struct ahc_softc *, + struct scb *); +static inline void ahc_notify_xfer_settings_change(struct ahc_softc *, + struct ahc_devinfo *); +static inline void ahc_platform_scb_free(struct ahc_softc *ahc, + struct scb *scb); +static inline void ahc_freeze_scb(struct scb *scb); + +static inline +void ahc_cmd_set_transaction_status(struct scsi_cmnd *cmd, uint32_t status) +{ + cmd->result &= ~(CAM_STATUS_MASK << 16); + cmd->result |= status << 16; +} + +static inline +void ahc_set_transaction_status(struct scb *scb, uint32_t status) +{ + ahc_cmd_set_transaction_status(scb->io_ctx,status); +} + +static inline +void ahc_cmd_set_scsi_status(struct scsi_cmnd *cmd, uint32_t status) +{ + cmd->result &= ~0xFFFF; + cmd->result |= status; +} + +static inline +void ahc_set_scsi_status(struct scb *scb, uint32_t status) +{ + ahc_cmd_set_scsi_status(scb->io_ctx, status); +} + +static inline +uint32_t ahc_cmd_get_transaction_status(struct scsi_cmnd *cmd) +{ + return ((cmd->result >> 16) & CAM_STATUS_MASK); +} + +static inline +uint32_t ahc_get_transaction_status(struct scb *scb) +{ + return (ahc_cmd_get_transaction_status(scb->io_ctx)); +} + +static inline +uint32_t ahc_cmd_get_scsi_status(struct scsi_cmnd *cmd) +{ + return (cmd->result & 0xFFFF); +} + +static inline +uint32_t ahc_get_scsi_status(struct scb *scb) +{ + return (ahc_cmd_get_scsi_status(scb->io_ctx)); +} + +static inline +void ahc_set_transaction_tag(struct scb *scb, int enabled, u_int type) +{ + /* + * Nothing to do for linux as the incoming transaction + * has no concept of tag/non tagged, etc. + */ +} + +static inline +u_long ahc_get_transfer_length(struct scb *scb) +{ + return (scb->platform_data->xfer_len); +} + +static inline +int ahc_get_transfer_dir(struct scb *scb) +{ + return (scb->io_ctx->sc_data_direction); +} + +static inline +void ahc_set_residual(struct scb *scb, u_long resid) +{ + scsi_set_resid(scb->io_ctx, resid); +} + +static inline +void ahc_set_sense_residual(struct scb *scb, u_long resid) +{ + scb->platform_data->sense_resid = resid; +} + +static inline +u_long ahc_get_residual(struct scb *scb) +{ + return scsi_get_resid(scb->io_ctx); +} + +static inline +u_long ahc_get_sense_residual(struct scb *scb) +{ + return (scb->platform_data->sense_resid); +} + +static inline +int ahc_perform_autosense(struct scb *scb) +{ + /* + * We always perform autosense in Linux. + * On other platforms this is set on a + * per-transaction basis. + */ + return (1); +} + +static inline uint32_t +ahc_get_sense_bufsize(struct ahc_softc *ahc, struct scb *scb) +{ + return (sizeof(struct scsi_sense_data)); +} + +static inline void +ahc_notify_xfer_settings_change(struct ahc_softc *ahc, + struct ahc_devinfo *devinfo) +{ + /* Nothing to do here for linux */ +} + +static inline void +ahc_platform_scb_free(struct ahc_softc *ahc, struct scb *scb) +{ +} + +int ahc_platform_alloc(struct ahc_softc *ahc, void *platform_arg); +void ahc_platform_free(struct ahc_softc *ahc); +void ahc_platform_freeze_devq(struct ahc_softc *ahc, struct scb *scb); + +static inline void +ahc_freeze_scb(struct scb *scb) +{ + if ((scb->io_ctx->result & (CAM_DEV_QFRZN << 16)) == 0) { + scb->io_ctx->result |= CAM_DEV_QFRZN << 16; + scb->platform_data->dev->qfrozen++; + } +} + +void ahc_platform_set_tags(struct ahc_softc *ahc, struct scsi_device *sdev, + struct ahc_devinfo *devinfo, ahc_queue_alg); +int ahc_platform_abort_scbs(struct ahc_softc *ahc, int target, + char channel, int lun, u_int tag, + role_t role, uint32_t status); +irqreturn_t + ahc_linux_isr(int irq, void *dev_id); +void ahc_platform_flushwork(struct ahc_softc *ahc); +void ahc_done(struct ahc_softc*, struct scb*); +void ahc_send_async(struct ahc_softc *, char channel, + u_int target, u_int lun, ac_code); +void ahc_print_path(struct ahc_softc *, struct scb *); + +#ifdef CONFIG_PCI +#define AHC_PCI_CONFIG 1 +#else +#define AHC_PCI_CONFIG 0 +#endif +#define bootverbose aic7xxx_verbose +extern u_int aic7xxx_verbose; +#endif /* _AIC7XXX_LINUX_H_ */ diff --git a/drivers/scsi/aic7xxx/aic7xxx_osm_pci.c b/drivers/scsi/aic7xxx/aic7xxx_osm_pci.c new file mode 100644 index 000000000..9b293b1f0 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx_osm_pci.c @@ -0,0 +1,471 @@ +/* + * Linux driver attachment glue for PCI based controllers. + * + * Copyright (c) 2000-2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic7xxx_osm_pci.c#47 $ + */ + +#include "aic7xxx_osm.h" +#include "aic7xxx_pci.h" + +/* Define the macro locally since it's different for different class of chips. +*/ +#define ID(x) ID_C(x, PCI_CLASS_STORAGE_SCSI) + +static const struct pci_device_id ahc_linux_pci_id_table[] = { + /* aic7850 based controllers */ + ID(ID_AHA_2902_04_10_15_20C_30C), + /* aic7860 based controllers */ + ID(ID_AHA_2930CU), + ID(ID_AHA_1480A & ID_DEV_VENDOR_MASK), + ID(ID_AHA_2940AU_0 & ID_DEV_VENDOR_MASK), + ID(ID_AHA_2940AU_CN & ID_DEV_VENDOR_MASK), + ID(ID_AHA_2930C_VAR & ID_DEV_VENDOR_MASK), + /* aic7870 based controllers */ + ID(ID_AHA_2940), + ID(ID_AHA_3940), + ID(ID_AHA_398X), + ID(ID_AHA_2944), + ID(ID_AHA_3944), + ID(ID_AHA_4944), + /* aic7880 based controllers */ + ID(ID_AHA_2940U & ID_DEV_VENDOR_MASK), + ID(ID_AHA_3940U & ID_DEV_VENDOR_MASK), + ID(ID_AHA_2944U & ID_DEV_VENDOR_MASK), + ID(ID_AHA_3944U & ID_DEV_VENDOR_MASK), + ID(ID_AHA_398XU & ID_DEV_VENDOR_MASK), + ID(ID_AHA_4944U & ID_DEV_VENDOR_MASK), + ID(ID_AHA_2930U & ID_DEV_VENDOR_MASK), + ID(ID_AHA_2940U_PRO & ID_DEV_VENDOR_MASK), + ID(ID_AHA_2940U_CN & ID_DEV_VENDOR_MASK), + /* aic7890 based controllers */ + ID(ID_AHA_2930U2), + ID(ID_AHA_2940U2B), + ID(ID_AHA_2940U2_OEM), + ID(ID_AHA_2940U2), + ID(ID_AHA_2950U2B), + ID16(ID_AIC7890_ARO & ID_AIC7895_ARO_MASK), + ID(ID_AAA_131U2), + /* aic7890 based controllers */ + ID(ID_AHA_29160), + ID(ID_AHA_29160_CPQ), + ID(ID_AHA_29160N), + ID(ID_AHA_29160C), + ID(ID_AHA_29160B), + ID(ID_AHA_19160B), + ID(ID_AIC7892_ARO), + /* aic7892 based controllers */ + ID(ID_AHA_2940U_DUAL), + ID(ID_AHA_3940AU), + ID(ID_AHA_3944AU), + ID(ID_AIC7895_ARO), + ID(ID_AHA_3950U2B_0), + ID(ID_AHA_3950U2B_1), + ID(ID_AHA_3950U2D_0), + ID(ID_AHA_3950U2D_1), + ID(ID_AIC7896_ARO), + /* aic7899 based controllers */ + ID(ID_AHA_3960D), + ID(ID_AHA_3960D_CPQ), + ID(ID_AIC7899_ARO), + /* Generic chip probes for devices we don't know exactly. */ + ID(ID_AIC7850 & ID_DEV_VENDOR_MASK), + ID(ID_AIC7855 & ID_DEV_VENDOR_MASK), + ID(ID_AIC7859 & ID_DEV_VENDOR_MASK), + ID(ID_AIC7860 & ID_DEV_VENDOR_MASK), + ID(ID_AIC7870 & ID_DEV_VENDOR_MASK), + ID(ID_AIC7880 & ID_DEV_VENDOR_MASK), + ID16(ID_AIC7890 & ID_9005_GENERIC_MASK), + ID16(ID_AIC7892 & ID_9005_GENERIC_MASK), + ID(ID_AIC7895 & ID_DEV_VENDOR_MASK), + ID16(ID_AIC7896 & ID_9005_GENERIC_MASK), + ID16(ID_AIC7899 & ID_9005_GENERIC_MASK), + ID(ID_AIC7810 & ID_DEV_VENDOR_MASK), + ID(ID_AIC7815 & ID_DEV_VENDOR_MASK), + { 0 } +}; + +MODULE_DEVICE_TABLE(pci, ahc_linux_pci_id_table); + +#ifdef CONFIG_PM +static int +ahc_linux_pci_dev_suspend(struct pci_dev *pdev, pm_message_t mesg) +{ + struct ahc_softc *ahc = pci_get_drvdata(pdev); + int rc; + + if ((rc = ahc_suspend(ahc))) + return rc; + + pci_save_state(pdev); + pci_disable_device(pdev); + + if (mesg.event & PM_EVENT_SLEEP) + pci_set_power_state(pdev, PCI_D3hot); + + return rc; +} + +static int +ahc_linux_pci_dev_resume(struct pci_dev *pdev) +{ + struct ahc_softc *ahc = pci_get_drvdata(pdev); + int rc; + + pci_set_power_state(pdev, PCI_D0); + pci_restore_state(pdev); + + if ((rc = pci_enable_device(pdev))) { + dev_printk(KERN_ERR, &pdev->dev, + "failed to enable device after resume (%d)\n", rc); + return rc; + } + + pci_set_master(pdev); + + ahc_pci_resume(ahc); + + return (ahc_resume(ahc)); +} +#endif + +static void +ahc_linux_pci_dev_remove(struct pci_dev *pdev) +{ + struct ahc_softc *ahc = pci_get_drvdata(pdev); + u_long s; + + if (ahc->platform_data && ahc->platform_data->host) + scsi_remove_host(ahc->platform_data->host); + + ahc_lock(ahc, &s); + ahc_intr_enable(ahc, FALSE); + ahc_unlock(ahc, &s); + ahc_free(ahc); +} + +static void +ahc_linux_pci_inherit_flags(struct ahc_softc *ahc) +{ + struct pci_dev *pdev = ahc->dev_softc, *master_pdev; + unsigned int master_devfn = PCI_DEVFN(PCI_SLOT(pdev->devfn), 0); + + master_pdev = pci_get_slot(pdev->bus, master_devfn); + if (master_pdev) { + struct ahc_softc *master = pci_get_drvdata(master_pdev); + if (master) { + ahc->flags &= ~AHC_BIOS_ENABLED; + ahc->flags |= master->flags & AHC_BIOS_ENABLED; + + ahc->flags &= ~AHC_PRIMARY_CHANNEL; + ahc->flags |= master->flags & AHC_PRIMARY_CHANNEL; + } else + printk(KERN_ERR "aic7xxx: no multichannel peer found!\n"); + pci_dev_put(master_pdev); + } +} + +static int +ahc_linux_pci_dev_probe(struct pci_dev *pdev, const struct pci_device_id *ent) +{ + char buf[80]; + const uint64_t mask_39bit = 0x7FFFFFFFFFULL; + struct ahc_softc *ahc; + ahc_dev_softc_t pci; + const struct ahc_pci_identity *entry; + char *name; + int error; + struct device *dev = &pdev->dev; + + pci = pdev; + entry = ahc_find_pci_device(pci); + if (entry == NULL) + return (-ENODEV); + + /* + * Allocate a softc for this card and + * set it up for attachment by our + * common detect routine. + */ + sprintf(buf, "ahc_pci:%d:%d:%d", + ahc_get_pci_bus(pci), + ahc_get_pci_slot(pci), + ahc_get_pci_function(pci)); + name = kstrdup(buf, GFP_ATOMIC); + if (name == NULL) + return (-ENOMEM); + ahc = ahc_alloc(NULL, name); + if (ahc == NULL) + return (-ENOMEM); + if (pci_enable_device(pdev)) { + ahc_free(ahc); + return (-ENODEV); + } + pci_set_master(pdev); + + if (sizeof(dma_addr_t) > 4 + && ahc->features & AHC_LARGE_SCBS + && dma_set_mask(dev, mask_39bit) == 0 + && dma_get_required_mask(dev) > DMA_BIT_MASK(32)) { + ahc->flags |= AHC_39BIT_ADDRESSING; + } else { + if (dma_set_mask(dev, DMA_BIT_MASK(32))) { + ahc_free(ahc); + printk(KERN_WARNING "aic7xxx: No suitable DMA available.\n"); + return (-ENODEV); + } + } + ahc->dev_softc = pci; + ahc->dev = &pci->dev; + error = ahc_pci_config(ahc, entry); + if (error != 0) { + ahc_free(ahc); + return (-error); + } + + /* + * Second Function PCI devices need to inherit some + * settings from function 0. + */ + if ((ahc->features & AHC_MULTI_FUNC) && PCI_FUNC(pdev->devfn) != 0) + ahc_linux_pci_inherit_flags(ahc); + + pci_set_drvdata(pdev, ahc); + ahc_linux_register_host(ahc, &aic7xxx_driver_template); + return (0); +} + +/******************************* PCI Routines *********************************/ +uint32_t +ahc_pci_read_config(ahc_dev_softc_t pci, int reg, int width) +{ + switch (width) { + case 1: + { + uint8_t retval; + + pci_read_config_byte(pci, reg, &retval); + return (retval); + } + case 2: + { + uint16_t retval; + pci_read_config_word(pci, reg, &retval); + return (retval); + } + case 4: + { + uint32_t retval; + pci_read_config_dword(pci, reg, &retval); + return (retval); + } + default: + panic("ahc_pci_read_config: Read size too big"); + /* NOTREACHED */ + return (0); + } +} + +void +ahc_pci_write_config(ahc_dev_softc_t pci, int reg, uint32_t value, int width) +{ + switch (width) { + case 1: + pci_write_config_byte(pci, reg, value); + break; + case 2: + pci_write_config_word(pci, reg, value); + break; + case 4: + pci_write_config_dword(pci, reg, value); + break; + default: + panic("ahc_pci_write_config: Write size too big"); + /* NOTREACHED */ + } +} + + +static struct pci_driver aic7xxx_pci_driver = { + .name = "aic7xxx", + .probe = ahc_linux_pci_dev_probe, +#ifdef CONFIG_PM + .suspend = ahc_linux_pci_dev_suspend, + .resume = ahc_linux_pci_dev_resume, +#endif + .remove = ahc_linux_pci_dev_remove, + .id_table = ahc_linux_pci_id_table +}; + +int +ahc_linux_pci_init(void) +{ + return pci_register_driver(&aic7xxx_pci_driver); +} + +void +ahc_linux_pci_exit(void) +{ + pci_unregister_driver(&aic7xxx_pci_driver); +} + +static int +ahc_linux_pci_reserve_io_region(struct ahc_softc *ahc, resource_size_t *base) +{ + if (aic7xxx_allow_memio == 0) + return (ENOMEM); + + *base = pci_resource_start(ahc->dev_softc, 0); + if (*base == 0) + return (ENOMEM); + if (!request_region(*base, 256, "aic7xxx")) + return (ENOMEM); + return (0); +} + +static int +ahc_linux_pci_reserve_mem_region(struct ahc_softc *ahc, + resource_size_t *bus_addr, + uint8_t __iomem **maddr) +{ + resource_size_t start; + int error; + + error = 0; + start = pci_resource_start(ahc->dev_softc, 1); + if (start != 0) { + *bus_addr = start; + if (!request_mem_region(start, 0x1000, "aic7xxx")) + error = ENOMEM; + if (error == 0) { + *maddr = ioremap(start, 256); + if (*maddr == NULL) { + error = ENOMEM; + release_mem_region(start, 0x1000); + } + } + } else + error = ENOMEM; + return (error); +} + +int +ahc_pci_map_registers(struct ahc_softc *ahc) +{ + uint32_t command; + resource_size_t base; + uint8_t __iomem *maddr; + int error; + + /* + * If its allowed, we prefer memory mapped access. + */ + command = ahc_pci_read_config(ahc->dev_softc, PCIR_COMMAND, 4); + command &= ~(PCIM_CMD_PORTEN|PCIM_CMD_MEMEN); + base = 0; + maddr = NULL; + error = ahc_linux_pci_reserve_mem_region(ahc, &base, &maddr); + if (error == 0) { + ahc->platform_data->mem_busaddr = base; + ahc->tag = BUS_SPACE_MEMIO; + ahc->bsh.maddr = maddr; + ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, + command | PCIM_CMD_MEMEN, 4); + + /* + * Do a quick test to see if memory mapped + * I/O is functioning correctly. + */ + if (ahc_pci_test_register_access(ahc) != 0) { + + printk("aic7xxx: PCI Device %d:%d:%d " + "failed memory mapped test. Using PIO.\n", + ahc_get_pci_bus(ahc->dev_softc), + ahc_get_pci_slot(ahc->dev_softc), + ahc_get_pci_function(ahc->dev_softc)); + iounmap(maddr); + release_mem_region(ahc->platform_data->mem_busaddr, + 0x1000); + ahc->bsh.maddr = NULL; + maddr = NULL; + } else + command |= PCIM_CMD_MEMEN; + } else { + printk("aic7xxx: PCI%d:%d:%d MEM region 0x%llx " + "unavailable. Cannot memory map device.\n", + ahc_get_pci_bus(ahc->dev_softc), + ahc_get_pci_slot(ahc->dev_softc), + ahc_get_pci_function(ahc->dev_softc), + (unsigned long long)base); + } + + /* + * We always prefer memory mapped access. + */ + if (maddr == NULL) { + + error = ahc_linux_pci_reserve_io_region(ahc, &base); + if (error == 0) { + ahc->tag = BUS_SPACE_PIO; + ahc->bsh.ioport = (u_long)base; + command |= PCIM_CMD_PORTEN; + } else { + printk("aic7xxx: PCI%d:%d:%d IO region 0x%llx[0..255] " + "unavailable. Cannot map device.\n", + ahc_get_pci_bus(ahc->dev_softc), + ahc_get_pci_slot(ahc->dev_softc), + ahc_get_pci_function(ahc->dev_softc), + (unsigned long long)base); + } + } + ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, command, 4); + return (error); +} + +int +ahc_pci_map_int(struct ahc_softc *ahc) +{ + int error; + + error = request_irq(ahc->dev_softc->irq, ahc_linux_isr, + IRQF_SHARED, "aic7xxx", ahc); + if (error == 0) + ahc->platform_data->irq = ahc->dev_softc->irq; + + return (-error); +} + diff --git a/drivers/scsi/aic7xxx/aic7xxx_pci.c b/drivers/scsi/aic7xxx/aic7xxx_pci.c new file mode 100644 index 000000000..656f680c7 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx_pci.c @@ -0,0 +1,2462 @@ +/* + * Product specific probe and attach routines for: + * 3940, 2940, aic7895, aic7890, aic7880, + * aic7870, aic7860 and aic7850 SCSI controllers + * + * Copyright (c) 1994-2001 Justin T. Gibbs. + * Copyright (c) 2000-2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aic7xxx_pci.c#79 $ + */ + +#include "aic7xxx_osm.h" +#include "aic7xxx_inline.h" +#include "aic7xxx_93cx6.h" +#include "aic7xxx_pci.h" + +static inline uint64_t +ahc_compose_id(u_int device, u_int vendor, u_int subdevice, u_int subvendor) +{ + uint64_t id; + + id = subvendor + | (subdevice << 16) + | ((uint64_t)vendor << 32) + | ((uint64_t)device << 48); + + return (id); +} + +#define AHC_PCI_IOADDR PCIR_MAPS /* I/O Address */ +#define AHC_PCI_MEMADDR (PCIR_MAPS + 4) /* Mem I/O Address */ + +#define DEVID_9005_TYPE(id) ((id) & 0xF) +#define DEVID_9005_TYPE_HBA 0x0 /* Standard Card */ +#define DEVID_9005_TYPE_AAA 0x3 /* RAID Card */ +#define DEVID_9005_TYPE_SISL 0x5 /* Container ROMB */ +#define DEVID_9005_TYPE_MB 0xF /* On Motherboard */ + +#define DEVID_9005_MAXRATE(id) (((id) & 0x30) >> 4) +#define DEVID_9005_MAXRATE_U160 0x0 +#define DEVID_9005_MAXRATE_ULTRA2 0x1 +#define DEVID_9005_MAXRATE_ULTRA 0x2 +#define DEVID_9005_MAXRATE_FAST 0x3 + +#define DEVID_9005_MFUNC(id) (((id) & 0x40) >> 6) + +#define DEVID_9005_CLASS(id) (((id) & 0xFF00) >> 8) +#define DEVID_9005_CLASS_SPI 0x0 /* Parallel SCSI */ + +#define SUBID_9005_TYPE(id) ((id) & 0xF) +#define SUBID_9005_TYPE_MB 0xF /* On Motherboard */ +#define SUBID_9005_TYPE_CARD 0x0 /* Standard Card */ +#define SUBID_9005_TYPE_LCCARD 0x1 /* Low Cost Card */ +#define SUBID_9005_TYPE_RAID 0x3 /* Combined with Raid */ + +#define SUBID_9005_TYPE_KNOWN(id) \ + ((((id) & 0xF) == SUBID_9005_TYPE_MB) \ + || (((id) & 0xF) == SUBID_9005_TYPE_CARD) \ + || (((id) & 0xF) == SUBID_9005_TYPE_LCCARD) \ + || (((id) & 0xF) == SUBID_9005_TYPE_RAID)) + +#define SUBID_9005_MAXRATE(id) (((id) & 0x30) >> 4) +#define SUBID_9005_MAXRATE_ULTRA2 0x0 +#define SUBID_9005_MAXRATE_ULTRA 0x1 +#define SUBID_9005_MAXRATE_U160 0x2 +#define SUBID_9005_MAXRATE_RESERVED 0x3 + +#define SUBID_9005_SEEPTYPE(id) \ + ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \ + ? ((id) & 0xC0) >> 6 \ + : ((id) & 0x300) >> 8) +#define SUBID_9005_SEEPTYPE_NONE 0x0 +#define SUBID_9005_SEEPTYPE_1K 0x1 +#define SUBID_9005_SEEPTYPE_2K_4K 0x2 +#define SUBID_9005_SEEPTYPE_RESERVED 0x3 +#define SUBID_9005_AUTOTERM(id) \ + ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \ + ? (((id) & 0x400) >> 10) == 0 \ + : (((id) & 0x40) >> 6) == 0) + +#define SUBID_9005_NUMCHAN(id) \ + ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \ + ? ((id) & 0x300) >> 8 \ + : ((id) & 0xC00) >> 10) + +#define SUBID_9005_LEGACYCONN(id) \ + ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \ + ? 0 \ + : ((id) & 0x80) >> 7) + +#define SUBID_9005_MFUNCENB(id) \ + ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \ + ? ((id) & 0x800) >> 11 \ + : ((id) & 0x1000) >> 12) +/* + * Informational only. Should use chip register to be + * certain, but may be use in identification strings. + */ +#define SUBID_9005_CARD_SCSIWIDTH_MASK 0x2000 +#define SUBID_9005_CARD_PCIWIDTH_MASK 0x4000 +#define SUBID_9005_CARD_SEDIFF_MASK 0x8000 + +static ahc_device_setup_t ahc_aic785X_setup; +static ahc_device_setup_t ahc_aic7860_setup; +static ahc_device_setup_t ahc_apa1480_setup; +static ahc_device_setup_t ahc_aic7870_setup; +static ahc_device_setup_t ahc_aic7870h_setup; +static ahc_device_setup_t ahc_aha394X_setup; +static ahc_device_setup_t ahc_aha394Xh_setup; +static ahc_device_setup_t ahc_aha494X_setup; +static ahc_device_setup_t ahc_aha494Xh_setup; +static ahc_device_setup_t ahc_aha398X_setup; +static ahc_device_setup_t ahc_aic7880_setup; +static ahc_device_setup_t ahc_aic7880h_setup; +static ahc_device_setup_t ahc_aha2940Pro_setup; +static ahc_device_setup_t ahc_aha394XU_setup; +static ahc_device_setup_t ahc_aha394XUh_setup; +static ahc_device_setup_t ahc_aha398XU_setup; +static ahc_device_setup_t ahc_aic7890_setup; +static ahc_device_setup_t ahc_aic7892_setup; +static ahc_device_setup_t ahc_aic7895_setup; +static ahc_device_setup_t ahc_aic7895h_setup; +static ahc_device_setup_t ahc_aic7896_setup; +static ahc_device_setup_t ahc_aic7899_setup; +static ahc_device_setup_t ahc_aha29160C_setup; +static ahc_device_setup_t ahc_raid_setup; +static ahc_device_setup_t ahc_aha394XX_setup; +static ahc_device_setup_t ahc_aha494XX_setup; +static ahc_device_setup_t ahc_aha398XX_setup; + +static const struct ahc_pci_identity ahc_pci_ident_table[] = { + /* aic7850 based controllers */ + { + ID_AHA_2902_04_10_15_20C_30C, + ID_ALL_MASK, + "Adaptec 2902/04/10/15/20C/30C SCSI adapter", + ahc_aic785X_setup + }, + /* aic7860 based controllers */ + { + ID_AHA_2930CU, + ID_ALL_MASK, + "Adaptec 2930CU SCSI adapter", + ahc_aic7860_setup + }, + { + ID_AHA_1480A & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 1480A Ultra SCSI adapter", + ahc_apa1480_setup + }, + { + ID_AHA_2940AU_0 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2940A Ultra SCSI adapter", + ahc_aic7860_setup + }, + { + ID_AHA_2940AU_CN & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2940A/CN Ultra SCSI adapter", + ahc_aic7860_setup + }, + { + ID_AHA_2930C_VAR & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2930C Ultra SCSI adapter (VAR)", + ahc_aic7860_setup + }, + /* aic7870 based controllers */ + { + ID_AHA_2940, + ID_ALL_MASK, + "Adaptec 2940 SCSI adapter", + ahc_aic7870_setup + }, + { + ID_AHA_3940, + ID_ALL_MASK, + "Adaptec 3940 SCSI adapter", + ahc_aha394X_setup + }, + { + ID_AHA_398X, + ID_ALL_MASK, + "Adaptec 398X SCSI RAID adapter", + ahc_aha398X_setup + }, + { + ID_AHA_2944, + ID_ALL_MASK, + "Adaptec 2944 SCSI adapter", + ahc_aic7870h_setup + }, + { + ID_AHA_3944, + ID_ALL_MASK, + "Adaptec 3944 SCSI adapter", + ahc_aha394Xh_setup + }, + { + ID_AHA_4944, + ID_ALL_MASK, + "Adaptec 4944 SCSI adapter", + ahc_aha494Xh_setup + }, + /* aic7880 based controllers */ + { + ID_AHA_2940U & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2940 Ultra SCSI adapter", + ahc_aic7880_setup + }, + { + ID_AHA_3940U & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 3940 Ultra SCSI adapter", + ahc_aha394XU_setup + }, + { + ID_AHA_2944U & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2944 Ultra SCSI adapter", + ahc_aic7880h_setup + }, + { + ID_AHA_3944U & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 3944 Ultra SCSI adapter", + ahc_aha394XUh_setup + }, + { + ID_AHA_398XU & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 398X Ultra SCSI RAID adapter", + ahc_aha398XU_setup + }, + { + /* + * XXX Don't know the slot numbers + * so we can't identify channels + */ + ID_AHA_4944U & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 4944 Ultra SCSI adapter", + ahc_aic7880h_setup + }, + { + ID_AHA_2930U & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2930 Ultra SCSI adapter", + ahc_aic7880_setup + }, + { + ID_AHA_2940U_PRO & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2940 Pro Ultra SCSI adapter", + ahc_aha2940Pro_setup + }, + { + ID_AHA_2940U_CN & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2940/CN Ultra SCSI adapter", + ahc_aic7880_setup + }, + /* Ignore all SISL (AAC on MB) based controllers. */ + { + ID_9005_SISL_ID, + ID_9005_SISL_MASK, + NULL, + NULL + }, + /* aic7890 based controllers */ + { + ID_AHA_2930U2, + ID_ALL_MASK, + "Adaptec 2930 Ultra2 SCSI adapter", + ahc_aic7890_setup + }, + { + ID_AHA_2940U2B, + ID_ALL_MASK, + "Adaptec 2940B Ultra2 SCSI adapter", + ahc_aic7890_setup + }, + { + ID_AHA_2940U2_OEM, + ID_ALL_MASK, + "Adaptec 2940 Ultra2 SCSI adapter (OEM)", + ahc_aic7890_setup + }, + { + ID_AHA_2940U2, + ID_ALL_MASK, + "Adaptec 2940 Ultra2 SCSI adapter", + ahc_aic7890_setup + }, + { + ID_AHA_2950U2B, + ID_ALL_MASK, + "Adaptec 2950 Ultra2 SCSI adapter", + ahc_aic7890_setup + }, + { + ID_AIC7890_ARO, + ID_ALL_MASK, + "Adaptec aic7890/91 Ultra2 SCSI adapter (ARO)", + ahc_aic7890_setup + }, + { + ID_AAA_131U2, + ID_ALL_MASK, + "Adaptec AAA-131 Ultra2 RAID adapter", + ahc_aic7890_setup + }, + /* aic7892 based controllers */ + { + ID_AHA_29160, + ID_ALL_MASK, + "Adaptec 29160 Ultra160 SCSI adapter", + ahc_aic7892_setup + }, + { + ID_AHA_29160_CPQ, + ID_ALL_MASK, + "Adaptec (Compaq OEM) 29160 Ultra160 SCSI adapter", + ahc_aic7892_setup + }, + { + ID_AHA_29160N, + ID_ALL_MASK, + "Adaptec 29160N Ultra160 SCSI adapter", + ahc_aic7892_setup + }, + { + ID_AHA_29160C, + ID_ALL_MASK, + "Adaptec 29160C Ultra160 SCSI adapter", + ahc_aha29160C_setup + }, + { + ID_AHA_29160B, + ID_ALL_MASK, + "Adaptec 29160B Ultra160 SCSI adapter", + ahc_aic7892_setup + }, + { + ID_AHA_19160B, + ID_ALL_MASK, + "Adaptec 19160B Ultra160 SCSI adapter", + ahc_aic7892_setup + }, + { + ID_AIC7892_ARO, + ID_ALL_MASK, + "Adaptec aic7892 Ultra160 SCSI adapter (ARO)", + ahc_aic7892_setup + }, + { + ID_AHA_2915_30LP, + ID_ALL_MASK, + "Adaptec 2915/30LP Ultra160 SCSI adapter", + ahc_aic7892_setup + }, + /* aic7895 based controllers */ + { + ID_AHA_2940U_DUAL, + ID_ALL_MASK, + "Adaptec 2940/DUAL Ultra SCSI adapter", + ahc_aic7895_setup + }, + { + ID_AHA_3940AU, + ID_ALL_MASK, + "Adaptec 3940A Ultra SCSI adapter", + ahc_aic7895_setup + }, + { + ID_AHA_3944AU, + ID_ALL_MASK, + "Adaptec 3944A Ultra SCSI adapter", + ahc_aic7895h_setup + }, + { + ID_AIC7895_ARO, + ID_AIC7895_ARO_MASK, + "Adaptec aic7895 Ultra SCSI adapter (ARO)", + ahc_aic7895_setup + }, + /* aic7896/97 based controllers */ + { + ID_AHA_3950U2B_0, + ID_ALL_MASK, + "Adaptec 3950B Ultra2 SCSI adapter", + ahc_aic7896_setup + }, + { + ID_AHA_3950U2B_1, + ID_ALL_MASK, + "Adaptec 3950B Ultra2 SCSI adapter", + ahc_aic7896_setup + }, + { + ID_AHA_3950U2D_0, + ID_ALL_MASK, + "Adaptec 3950D Ultra2 SCSI adapter", + ahc_aic7896_setup + }, + { + ID_AHA_3950U2D_1, + ID_ALL_MASK, + "Adaptec 3950D Ultra2 SCSI adapter", + ahc_aic7896_setup + }, + { + ID_AIC7896_ARO, + ID_ALL_MASK, + "Adaptec aic7896/97 Ultra2 SCSI adapter (ARO)", + ahc_aic7896_setup + }, + /* aic7899 based controllers */ + { + ID_AHA_3960D, + ID_ALL_MASK, + "Adaptec 3960D Ultra160 SCSI adapter", + ahc_aic7899_setup + }, + { + ID_AHA_3960D_CPQ, + ID_ALL_MASK, + "Adaptec (Compaq OEM) 3960D Ultra160 SCSI adapter", + ahc_aic7899_setup + }, + { + ID_AIC7899_ARO, + ID_ALL_MASK, + "Adaptec aic7899 Ultra160 SCSI adapter (ARO)", + ahc_aic7899_setup + }, + /* Generic chip probes for devices we don't know 'exactly' */ + { + ID_AIC7850 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7850 SCSI adapter", + ahc_aic785X_setup + }, + { + ID_AIC7855 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7855 SCSI adapter", + ahc_aic785X_setup + }, + { + ID_AIC7859 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7859 SCSI adapter", + ahc_aic7860_setup + }, + { + ID_AIC7860 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7860 Ultra SCSI adapter", + ahc_aic7860_setup + }, + { + ID_AIC7870 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7870 SCSI adapter", + ahc_aic7870_setup + }, + { + ID_AIC7880 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7880 Ultra SCSI adapter", + ahc_aic7880_setup + }, + { + ID_AIC7890 & ID_9005_GENERIC_MASK, + ID_9005_GENERIC_MASK, + "Adaptec aic7890/91 Ultra2 SCSI adapter", + ahc_aic7890_setup + }, + { + ID_AIC7892 & ID_9005_GENERIC_MASK, + ID_9005_GENERIC_MASK, + "Adaptec aic7892 Ultra160 SCSI adapter", + ahc_aic7892_setup + }, + { + ID_AIC7895 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7895 Ultra SCSI adapter", + ahc_aic7895_setup + }, + { + ID_AIC7896 & ID_9005_GENERIC_MASK, + ID_9005_GENERIC_MASK, + "Adaptec aic7896/97 Ultra2 SCSI adapter", + ahc_aic7896_setup + }, + { + ID_AIC7899 & ID_9005_GENERIC_MASK, + ID_9005_GENERIC_MASK, + "Adaptec aic7899 Ultra160 SCSI adapter", + ahc_aic7899_setup + }, + { + ID_AIC7810 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7810 RAID memory controller", + ahc_raid_setup + }, + { + ID_AIC7815 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7815 RAID memory controller", + ahc_raid_setup + } +}; + +static const u_int ahc_num_pci_devs = ARRAY_SIZE(ahc_pci_ident_table); + +#define AHC_394X_SLOT_CHANNEL_A 4 +#define AHC_394X_SLOT_CHANNEL_B 5 + +#define AHC_398X_SLOT_CHANNEL_A 4 +#define AHC_398X_SLOT_CHANNEL_B 8 +#define AHC_398X_SLOT_CHANNEL_C 12 + +#define AHC_494X_SLOT_CHANNEL_A 4 +#define AHC_494X_SLOT_CHANNEL_B 5 +#define AHC_494X_SLOT_CHANNEL_C 6 +#define AHC_494X_SLOT_CHANNEL_D 7 + +#define DEVCONFIG 0x40 +#define PCIERRGENDIS 0x80000000ul +#define SCBSIZE32 0x00010000ul /* aic789X only */ +#define REXTVALID 0x00001000ul /* ultra cards only */ +#define MPORTMODE 0x00000400ul /* aic7870+ only */ +#define RAMPSM 0x00000200ul /* aic7870+ only */ +#define VOLSENSE 0x00000100ul +#define PCI64BIT 0x00000080ul /* 64Bit PCI bus (Ultra2 Only)*/ +#define SCBRAMSEL 0x00000080ul +#define MRDCEN 0x00000040ul +#define EXTSCBTIME 0x00000020ul /* aic7870 only */ +#define EXTSCBPEN 0x00000010ul /* aic7870 only */ +#define BERREN 0x00000008ul +#define DACEN 0x00000004ul +#define STPWLEVEL 0x00000002ul +#define DIFACTNEGEN 0x00000001ul /* aic7870 only */ + +#define CSIZE_LATTIME 0x0c +#define CACHESIZE 0x0000003ful /* only 5 bits */ +#define LATTIME 0x0000ff00ul + +/* PCI STATUS definitions */ +#define DPE 0x80 +#define SSE 0x40 +#define RMA 0x20 +#define RTA 0x10 +#define STA 0x08 +#define DPR 0x01 + +static int ahc_9005_subdevinfo_valid(uint16_t device, uint16_t vendor, + uint16_t subdevice, uint16_t subvendor); +static int ahc_ext_scbram_present(struct ahc_softc *ahc); +static void ahc_scbram_config(struct ahc_softc *ahc, int enable, + int pcheck, int fast, int large); +static void ahc_probe_ext_scbram(struct ahc_softc *ahc); +static void check_extport(struct ahc_softc *ahc, u_int *sxfrctl1); +static void ahc_parse_pci_eeprom(struct ahc_softc *ahc, + struct seeprom_config *sc); +static void configure_termination(struct ahc_softc *ahc, + struct seeprom_descriptor *sd, + u_int adapter_control, + u_int *sxfrctl1); + +static void ahc_new_term_detect(struct ahc_softc *ahc, + int *enableSEC_low, + int *enableSEC_high, + int *enablePRI_low, + int *enablePRI_high, + int *eeprom_present); +static void aic787X_cable_detect(struct ahc_softc *ahc, int *internal50_present, + int *internal68_present, + int *externalcable_present, + int *eeprom_present); +static void aic785X_cable_detect(struct ahc_softc *ahc, int *internal50_present, + int *externalcable_present, + int *eeprom_present); +static void write_brdctl(struct ahc_softc *ahc, uint8_t value); +static uint8_t read_brdctl(struct ahc_softc *ahc); +static void ahc_pci_intr(struct ahc_softc *ahc); +static int ahc_pci_chip_init(struct ahc_softc *ahc); + +static int +ahc_9005_subdevinfo_valid(uint16_t device, uint16_t vendor, + uint16_t subdevice, uint16_t subvendor) +{ + int result; + + /* Default to invalid. */ + result = 0; + if (vendor == 0x9005 + && subvendor == 0x9005 + && subdevice != device + && SUBID_9005_TYPE_KNOWN(subdevice) != 0) { + + switch (SUBID_9005_TYPE(subdevice)) { + case SUBID_9005_TYPE_MB: + break; + case SUBID_9005_TYPE_CARD: + case SUBID_9005_TYPE_LCCARD: + /* + * Currently only trust Adaptec cards to + * get the sub device info correct. + */ + if (DEVID_9005_TYPE(device) == DEVID_9005_TYPE_HBA) + result = 1; + break; + case SUBID_9005_TYPE_RAID: + break; + default: + break; + } + } + return (result); +} + +const struct ahc_pci_identity * +ahc_find_pci_device(ahc_dev_softc_t pci) +{ + uint64_t full_id; + uint16_t device; + uint16_t vendor; + uint16_t subdevice; + uint16_t subvendor; + const struct ahc_pci_identity *entry; + u_int i; + + vendor = ahc_pci_read_config(pci, PCIR_DEVVENDOR, /*bytes*/2); + device = ahc_pci_read_config(pci, PCIR_DEVICE, /*bytes*/2); + subvendor = ahc_pci_read_config(pci, PCIR_SUBVEND_0, /*bytes*/2); + subdevice = ahc_pci_read_config(pci, PCIR_SUBDEV_0, /*bytes*/2); + full_id = ahc_compose_id(device, vendor, subdevice, subvendor); + + /* + * If the second function is not hooked up, ignore it. + * Unfortunately, not all MB vendors implement the + * subdevice ID as per the Adaptec spec, so do our best + * to sanity check it prior to accepting the subdevice + * ID as valid. + */ + if (ahc_get_pci_function(pci) > 0 + && ahc_9005_subdevinfo_valid(device, vendor, subdevice, subvendor) + && SUBID_9005_MFUNCENB(subdevice) == 0) + return (NULL); + + for (i = 0; i < ahc_num_pci_devs; i++) { + entry = &ahc_pci_ident_table[i]; + if (entry->full_id == (full_id & entry->id_mask)) { + /* Honor exclusion entries. */ + if (entry->name == NULL) + return (NULL); + return (entry); + } + } + return (NULL); +} + +int +ahc_pci_config(struct ahc_softc *ahc, const struct ahc_pci_identity *entry) +{ + u_int command; + u_int our_id; + u_int sxfrctl1; + u_int scsiseq; + u_int dscommand0; + uint32_t devconfig; + int error; + uint8_t sblkctl; + + our_id = 0; + error = entry->setup(ahc); + if (error != 0) + return (error); + ahc->chip |= AHC_PCI; + ahc->description = entry->name; + + pci_set_power_state(ahc->dev_softc, AHC_POWER_STATE_D0); + + error = ahc_pci_map_registers(ahc); + if (error != 0) + return (error); + + /* + * Before we continue probing the card, ensure that + * its interrupts are *disabled*. We don't want + * a misstep to hang the machine in an interrupt + * storm. + */ + ahc_intr_enable(ahc, FALSE); + + devconfig = ahc_pci_read_config(ahc->dev_softc, DEVCONFIG, /*bytes*/4); + + /* + * If we need to support high memory, enable dual + * address cycles. This bit must be set to enable + * high address bit generation even if we are on a + * 64bit bus (PCI64BIT set in devconfig). + */ + if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) { + + if (bootverbose) + printk("%s: Enabling 39Bit Addressing\n", + ahc_name(ahc)); + devconfig |= DACEN; + } + + /* Ensure that pci error generation, a test feature, is disabled. */ + devconfig |= PCIERRGENDIS; + + ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, devconfig, /*bytes*/4); + + /* Ensure busmastering is enabled */ + command = ahc_pci_read_config(ahc->dev_softc, PCIR_COMMAND, /*bytes*/2); + command |= PCIM_CMD_BUSMASTEREN; + + ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, command, /*bytes*/2); + + /* On all PCI adapters, we allow SCB paging */ + ahc->flags |= AHC_PAGESCBS; + + error = ahc_softc_init(ahc); + if (error != 0) + return (error); + + /* + * Disable PCI parity error checking. Users typically + * do this to work around broken PCI chipsets that get + * the parity timing wrong and thus generate lots of spurious + * errors. The chip only allows us to disable *all* parity + * error reporting when doing this, so CIO bus, scb ram, and + * scratch ram parity errors will be ignored too. + */ + if ((ahc->flags & AHC_DISABLE_PCI_PERR) != 0) + ahc->seqctl |= FAILDIS; + + ahc->bus_intr = ahc_pci_intr; + ahc->bus_chip_init = ahc_pci_chip_init; + + /* Remember how the card was setup in case there is no SEEPROM */ + if ((ahc_inb(ahc, HCNTRL) & POWRDN) == 0) { + ahc_pause(ahc); + if ((ahc->features & AHC_ULTRA2) != 0) + our_id = ahc_inb(ahc, SCSIID_ULTRA2) & OID; + else + our_id = ahc_inb(ahc, SCSIID) & OID; + sxfrctl1 = ahc_inb(ahc, SXFRCTL1) & STPWEN; + scsiseq = ahc_inb(ahc, SCSISEQ); + } else { + sxfrctl1 = STPWEN; + our_id = 7; + scsiseq = 0; + } + + error = ahc_reset(ahc, /*reinit*/FALSE); + if (error != 0) + return (ENXIO); + + if ((ahc->features & AHC_DT) != 0) { + u_int sfunct; + + /* Perform ALT-Mode Setup */ + sfunct = ahc_inb(ahc, SFUNCT) & ~ALT_MODE; + ahc_outb(ahc, SFUNCT, sfunct | ALT_MODE); + ahc_outb(ahc, OPTIONMODE, + OPTIONMODE_DEFAULTS|AUTOACKEN|BUSFREEREV|EXPPHASEDIS); + ahc_outb(ahc, SFUNCT, sfunct); + + /* Normal mode setup */ + ahc_outb(ahc, CRCCONTROL1, CRCVALCHKEN|CRCENDCHKEN|CRCREQCHKEN + |TARGCRCENDEN); + } + + dscommand0 = ahc_inb(ahc, DSCOMMAND0); + dscommand0 |= MPARCKEN|CACHETHEN; + if ((ahc->features & AHC_ULTRA2) != 0) { + + /* + * DPARCKEN doesn't work correctly on + * some MBs so don't use it. + */ + dscommand0 &= ~DPARCKEN; + } + + /* + * Handle chips that must have cache line + * streaming (dis/en)abled. + */ + if ((ahc->bugs & AHC_CACHETHEN_DIS_BUG) != 0) + dscommand0 |= CACHETHEN; + + if ((ahc->bugs & AHC_CACHETHEN_BUG) != 0) + dscommand0 &= ~CACHETHEN; + + ahc_outb(ahc, DSCOMMAND0, dscommand0); + + ahc->pci_cachesize = + ahc_pci_read_config(ahc->dev_softc, CSIZE_LATTIME, + /*bytes*/1) & CACHESIZE; + ahc->pci_cachesize *= 4; + + if ((ahc->bugs & AHC_PCI_2_1_RETRY_BUG) != 0 + && ahc->pci_cachesize == 4) { + + ahc_pci_write_config(ahc->dev_softc, CSIZE_LATTIME, + 0, /*bytes*/1); + ahc->pci_cachesize = 0; + } + + /* + * We cannot perform ULTRA speeds without the presence + * of the external precision resistor. + */ + if ((ahc->features & AHC_ULTRA) != 0) { + uint32_t devconfig; + + devconfig = ahc_pci_read_config(ahc->dev_softc, + DEVCONFIG, /*bytes*/4); + if ((devconfig & REXTVALID) == 0) + ahc->features &= ~AHC_ULTRA; + } + + /* See if we have a SEEPROM and perform auto-term */ + check_extport(ahc, &sxfrctl1); + + /* + * Take the LED out of diagnostic mode + */ + sblkctl = ahc_inb(ahc, SBLKCTL); + ahc_outb(ahc, SBLKCTL, (sblkctl & ~(DIAGLEDEN|DIAGLEDON))); + + if ((ahc->features & AHC_ULTRA2) != 0) { + ahc_outb(ahc, DFF_THRSH, RD_DFTHRSH_MAX|WR_DFTHRSH_MAX); + } else { + ahc_outb(ahc, DSPCISTATUS, DFTHRSH_100); + } + + if (ahc->flags & AHC_USEDEFAULTS) { + /* + * PCI Adapter default setup + * Should only be used if the adapter does not have + * a SEEPROM. + */ + /* See if someone else set us up already */ + if ((ahc->flags & AHC_NO_BIOS_INIT) == 0 + && scsiseq != 0) { + printk("%s: Using left over BIOS settings\n", + ahc_name(ahc)); + ahc->flags &= ~AHC_USEDEFAULTS; + ahc->flags |= AHC_BIOS_ENABLED; + } else { + /* + * Assume only one connector and always turn + * on termination. + */ + our_id = 0x07; + sxfrctl1 = STPWEN; + } + ahc_outb(ahc, SCSICONF, our_id|ENSPCHK|RESET_SCSI); + + ahc->our_id = our_id; + } + + /* + * Take a look to see if we have external SRAM. + * We currently do not attempt to use SRAM that is + * shared among multiple controllers. + */ + ahc_probe_ext_scbram(ahc); + + /* + * Record our termination setting for the + * generic initialization routine. + */ + if ((sxfrctl1 & STPWEN) != 0) + ahc->flags |= AHC_TERM_ENB_A; + + /* + * Save chip register configuration data for chip resets + * that occur during runtime and resume events. + */ + ahc->bus_softc.pci_softc.devconfig = + ahc_pci_read_config(ahc->dev_softc, DEVCONFIG, /*bytes*/4); + ahc->bus_softc.pci_softc.command = + ahc_pci_read_config(ahc->dev_softc, PCIR_COMMAND, /*bytes*/1); + ahc->bus_softc.pci_softc.csize_lattime = + ahc_pci_read_config(ahc->dev_softc, CSIZE_LATTIME, /*bytes*/1); + ahc->bus_softc.pci_softc.dscommand0 = ahc_inb(ahc, DSCOMMAND0); + ahc->bus_softc.pci_softc.dspcistatus = ahc_inb(ahc, DSPCISTATUS); + if ((ahc->features & AHC_DT) != 0) { + u_int sfunct; + + sfunct = ahc_inb(ahc, SFUNCT) & ~ALT_MODE; + ahc_outb(ahc, SFUNCT, sfunct | ALT_MODE); + ahc->bus_softc.pci_softc.optionmode = ahc_inb(ahc, OPTIONMODE); + ahc->bus_softc.pci_softc.targcrccnt = ahc_inw(ahc, TARGCRCCNT); + ahc_outb(ahc, SFUNCT, sfunct); + ahc->bus_softc.pci_softc.crccontrol1 = + ahc_inb(ahc, CRCCONTROL1); + } + if ((ahc->features & AHC_MULTI_FUNC) != 0) + ahc->bus_softc.pci_softc.scbbaddr = ahc_inb(ahc, SCBBADDR); + + if ((ahc->features & AHC_ULTRA2) != 0) + ahc->bus_softc.pci_softc.dff_thrsh = ahc_inb(ahc, DFF_THRSH); + + /* Core initialization */ + error = ahc_init(ahc); + if (error != 0) + return (error); + ahc->init_level++; + + /* + * Allow interrupts now that we are completely setup. + */ + return ahc_pci_map_int(ahc); +} + +/* + * Test for the presence of external sram in an + * "unshared" configuration. + */ +static int +ahc_ext_scbram_present(struct ahc_softc *ahc) +{ + u_int chip; + int ramps; + int single_user; + uint32_t devconfig; + + chip = ahc->chip & AHC_CHIPID_MASK; + devconfig = ahc_pci_read_config(ahc->dev_softc, + DEVCONFIG, /*bytes*/4); + single_user = (devconfig & MPORTMODE) != 0; + + if ((ahc->features & AHC_ULTRA2) != 0) + ramps = (ahc_inb(ahc, DSCOMMAND0) & RAMPS) != 0; + else if (chip == AHC_AIC7895 || chip == AHC_AIC7895C) + /* + * External SCBRAM arbitration is flakey + * on these chips. Unfortunately this means + * we don't use the extra SCB ram space on the + * 3940AUW. + */ + ramps = 0; + else if (chip >= AHC_AIC7870) + ramps = (devconfig & RAMPSM) != 0; + else + ramps = 0; + + if (ramps && single_user) + return (1); + return (0); +} + +/* + * Enable external scbram. + */ +static void +ahc_scbram_config(struct ahc_softc *ahc, int enable, int pcheck, + int fast, int large) +{ + uint32_t devconfig; + + if (ahc->features & AHC_MULTI_FUNC) { + /* + * Set the SCB Base addr (highest address bit) + * depending on which channel we are. + */ + ahc_outb(ahc, SCBBADDR, ahc_get_pci_function(ahc->dev_softc)); + } + + ahc->flags &= ~AHC_LSCBS_ENABLED; + if (large) + ahc->flags |= AHC_LSCBS_ENABLED; + devconfig = ahc_pci_read_config(ahc->dev_softc, DEVCONFIG, /*bytes*/4); + if ((ahc->features & AHC_ULTRA2) != 0) { + u_int dscommand0; + + dscommand0 = ahc_inb(ahc, DSCOMMAND0); + if (enable) + dscommand0 &= ~INTSCBRAMSEL; + else + dscommand0 |= INTSCBRAMSEL; + if (large) + dscommand0 &= ~USCBSIZE32; + else + dscommand0 |= USCBSIZE32; + ahc_outb(ahc, DSCOMMAND0, dscommand0); + } else { + if (fast) + devconfig &= ~EXTSCBTIME; + else + devconfig |= EXTSCBTIME; + if (enable) + devconfig &= ~SCBRAMSEL; + else + devconfig |= SCBRAMSEL; + if (large) + devconfig &= ~SCBSIZE32; + else + devconfig |= SCBSIZE32; + } + if (pcheck) + devconfig |= EXTSCBPEN; + else + devconfig &= ~EXTSCBPEN; + + ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, devconfig, /*bytes*/4); +} + +/* + * Take a look to see if we have external SRAM. + * We currently do not attempt to use SRAM that is + * shared among multiple controllers. + */ +static void +ahc_probe_ext_scbram(struct ahc_softc *ahc) +{ + int num_scbs; + int test_num_scbs; + int enable; + int pcheck; + int fast; + int large; + + enable = FALSE; + pcheck = FALSE; + fast = FALSE; + large = FALSE; + num_scbs = 0; + + if (ahc_ext_scbram_present(ahc) == 0) + goto done; + + /* + * Probe for the best parameters to use. + */ + ahc_scbram_config(ahc, /*enable*/TRUE, pcheck, fast, large); + num_scbs = ahc_probe_scbs(ahc); + if (num_scbs == 0) { + /* The SRAM wasn't really present. */ + goto done; + } + enable = TRUE; + + /* + * Clear any outstanding parity error + * and ensure that parity error reporting + * is enabled. + */ + ahc_outb(ahc, SEQCTL, 0); + ahc_outb(ahc, CLRINT, CLRPARERR); + ahc_outb(ahc, CLRINT, CLRBRKADRINT); + + /* Now see if we can do parity */ + ahc_scbram_config(ahc, enable, /*pcheck*/TRUE, fast, large); + num_scbs = ahc_probe_scbs(ahc); + if ((ahc_inb(ahc, INTSTAT) & BRKADRINT) == 0 + || (ahc_inb(ahc, ERROR) & MPARERR) == 0) + pcheck = TRUE; + + /* Clear any resulting parity error */ + ahc_outb(ahc, CLRINT, CLRPARERR); + ahc_outb(ahc, CLRINT, CLRBRKADRINT); + + /* Now see if we can do fast timing */ + ahc_scbram_config(ahc, enable, pcheck, /*fast*/TRUE, large); + test_num_scbs = ahc_probe_scbs(ahc); + if (test_num_scbs == num_scbs + && ((ahc_inb(ahc, INTSTAT) & BRKADRINT) == 0 + || (ahc_inb(ahc, ERROR) & MPARERR) == 0)) + fast = TRUE; + + /* + * See if we can use large SCBs and still maintain + * the same overall count of SCBs. + */ + if ((ahc->features & AHC_LARGE_SCBS) != 0) { + ahc_scbram_config(ahc, enable, pcheck, fast, /*large*/TRUE); + test_num_scbs = ahc_probe_scbs(ahc); + if (test_num_scbs >= num_scbs) { + large = TRUE; + num_scbs = test_num_scbs; + if (num_scbs >= 64) { + /* + * We have enough space to move the + * "busy targets table" into SCB space + * and make it qualify all the way to the + * lun level. + */ + ahc->flags |= AHC_SCB_BTT; + } + } + } +done: + /* + * Disable parity error reporting until we + * can load instruction ram. + */ + ahc_outb(ahc, SEQCTL, PERRORDIS|FAILDIS); + /* Clear any latched parity error */ + ahc_outb(ahc, CLRINT, CLRPARERR); + ahc_outb(ahc, CLRINT, CLRBRKADRINT); + if (bootverbose && enable) { + printk("%s: External SRAM, %s access%s, %dbytes/SCB\n", + ahc_name(ahc), fast ? "fast" : "slow", + pcheck ? ", parity checking enabled" : "", + large ? 64 : 32); + } + ahc_scbram_config(ahc, enable, pcheck, fast, large); +} + +/* + * Perform some simple tests that should catch situations where + * our registers are invalidly mapped. + */ +int +ahc_pci_test_register_access(struct ahc_softc *ahc) +{ + int error; + u_int status1; + uint32_t cmd; + uint8_t hcntrl; + + error = EIO; + + /* + * Enable PCI error interrupt status, but suppress NMIs + * generated by SERR raised due to target aborts. + */ + cmd = ahc_pci_read_config(ahc->dev_softc, PCIR_COMMAND, /*bytes*/2); + ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, + cmd & ~PCIM_CMD_SERRESPEN, /*bytes*/2); + + /* + * First a simple test to see if any + * registers can be read. Reading + * HCNTRL has no side effects and has + * at least one bit that is guaranteed to + * be zero so it is a good register to + * use for this test. + */ + hcntrl = ahc_inb(ahc, HCNTRL); + + if (hcntrl == 0xFF) + goto fail; + + if ((hcntrl & CHIPRST) != 0) { + /* + * The chip has not been initialized since + * PCI/EISA/VLB bus reset. Don't trust + * "left over BIOS data". + */ + ahc->flags |= AHC_NO_BIOS_INIT; + } + + /* + * Next create a situation where write combining + * or read prefetching could be initiated by the + * CPU or host bridge. Our device does not support + * either, so look for data corruption and/or flagged + * PCI errors. First pause without causing another + * chip reset. + */ + hcntrl &= ~CHIPRST; + ahc_outb(ahc, HCNTRL, hcntrl|PAUSE); + while (ahc_is_paused(ahc) == 0) + ; + + /* Clear any PCI errors that occurred before our driver attached. */ + status1 = ahc_pci_read_config(ahc->dev_softc, + PCIR_STATUS + 1, /*bytes*/1); + ahc_pci_write_config(ahc->dev_softc, PCIR_STATUS + 1, + status1, /*bytes*/1); + ahc_outb(ahc, CLRINT, CLRPARERR); + + ahc_outb(ahc, SEQCTL, PERRORDIS); + ahc_outb(ahc, SCBPTR, 0); + ahc_outl(ahc, SCB_BASE, 0x5aa555aa); + if (ahc_inl(ahc, SCB_BASE) != 0x5aa555aa) + goto fail; + + status1 = ahc_pci_read_config(ahc->dev_softc, + PCIR_STATUS + 1, /*bytes*/1); + if ((status1 & STA) != 0) + goto fail; + + error = 0; + +fail: + /* Silently clear any latched errors. */ + status1 = ahc_pci_read_config(ahc->dev_softc, + PCIR_STATUS + 1, /*bytes*/1); + ahc_pci_write_config(ahc->dev_softc, PCIR_STATUS + 1, + status1, /*bytes*/1); + ahc_outb(ahc, CLRINT, CLRPARERR); + ahc_outb(ahc, SEQCTL, PERRORDIS|FAILDIS); + ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, cmd, /*bytes*/2); + return (error); +} + +/* + * Check the external port logic for a serial eeprom + * and termination/cable detection contrls. + */ +static void +check_extport(struct ahc_softc *ahc, u_int *sxfrctl1) +{ + struct seeprom_descriptor sd; + struct seeprom_config *sc; + int have_seeprom; + int have_autoterm; + + sd.sd_ahc = ahc; + sd.sd_control_offset = SEECTL; + sd.sd_status_offset = SEECTL; + sd.sd_dataout_offset = SEECTL; + sc = ahc->seep_config; + + /* + * For some multi-channel devices, the c46 is simply too + * small to work. For the other controller types, we can + * get our information from either SEEPROM type. Set the + * type to start our probe with accordingly. + */ + if (ahc->flags & AHC_LARGE_SEEPROM) + sd.sd_chip = C56_66; + else + sd.sd_chip = C46; + + sd.sd_MS = SEEMS; + sd.sd_RDY = SEERDY; + sd.sd_CS = SEECS; + sd.sd_CK = SEECK; + sd.sd_DO = SEEDO; + sd.sd_DI = SEEDI; + + have_seeprom = ahc_acquire_seeprom(ahc, &sd); + if (have_seeprom) { + + if (bootverbose) + printk("%s: Reading SEEPROM...", ahc_name(ahc)); + + for (;;) { + u_int start_addr; + + start_addr = 32 * (ahc->channel - 'A'); + + have_seeprom = ahc_read_seeprom(&sd, (uint16_t *)sc, + start_addr, + sizeof(*sc)/2); + + if (have_seeprom) + have_seeprom = ahc_verify_cksum(sc); + + if (have_seeprom != 0 || sd.sd_chip == C56_66) { + if (bootverbose) { + if (have_seeprom == 0) + printk ("checksum error\n"); + else + printk ("done.\n"); + } + break; + } + sd.sd_chip = C56_66; + } + ahc_release_seeprom(&sd); + + /* Remember the SEEPROM type for later */ + if (sd.sd_chip == C56_66) + ahc->flags |= AHC_LARGE_SEEPROM; + } + + if (!have_seeprom) { + /* + * Pull scratch ram settings and treat them as + * if they are the contents of an seeprom if + * the 'ADPT' signature is found in SCB2. + * We manually compose the data as 16bit values + * to avoid endian issues. + */ + ahc_outb(ahc, SCBPTR, 2); + if (ahc_inb(ahc, SCB_BASE) == 'A' + && ahc_inb(ahc, SCB_BASE + 1) == 'D' + && ahc_inb(ahc, SCB_BASE + 2) == 'P' + && ahc_inb(ahc, SCB_BASE + 3) == 'T') { + uint16_t *sc_data; + int i; + + sc_data = (uint16_t *)sc; + for (i = 0; i < 32; i++, sc_data++) { + int j; + + j = i * 2; + *sc_data = ahc_inb(ahc, SRAM_BASE + j) + | ahc_inb(ahc, SRAM_BASE + j + 1) << 8; + } + have_seeprom = ahc_verify_cksum(sc); + if (have_seeprom) + ahc->flags |= AHC_SCB_CONFIG_USED; + } + /* + * Clear any SCB parity errors in case this data and + * its associated parity was not initialized by the BIOS + */ + ahc_outb(ahc, CLRINT, CLRPARERR); + ahc_outb(ahc, CLRINT, CLRBRKADRINT); + } + + if (!have_seeprom) { + if (bootverbose) + printk("%s: No SEEPROM available.\n", ahc_name(ahc)); + ahc->flags |= AHC_USEDEFAULTS; + kfree(ahc->seep_config); + ahc->seep_config = NULL; + sc = NULL; + } else { + ahc_parse_pci_eeprom(ahc, sc); + } + + /* + * Cards that have the external logic necessary to talk to + * a SEEPROM, are almost certain to have the remaining logic + * necessary for auto-termination control. This assumption + * hasn't failed yet... + */ + have_autoterm = have_seeprom; + + /* + * Some low-cost chips have SEEPROM and auto-term control built + * in, instead of using a GAL. They can tell us directly + * if the termination logic is enabled. + */ + if ((ahc->features & AHC_SPIOCAP) != 0) { + if ((ahc_inb(ahc, SPIOCAP) & SSPIOCPS) == 0) + have_autoterm = FALSE; + } + + if (have_autoterm) { + ahc->flags |= AHC_HAS_TERM_LOGIC; + ahc_acquire_seeprom(ahc, &sd); + configure_termination(ahc, &sd, sc->adapter_control, sxfrctl1); + ahc_release_seeprom(&sd); + } else if (have_seeprom) { + *sxfrctl1 &= ~STPWEN; + if ((sc->adapter_control & CFSTERM) != 0) + *sxfrctl1 |= STPWEN; + if (bootverbose) + printk("%s: Low byte termination %sabled\n", + ahc_name(ahc), + (*sxfrctl1 & STPWEN) ? "en" : "dis"); + } +} + +static void +ahc_parse_pci_eeprom(struct ahc_softc *ahc, struct seeprom_config *sc) +{ + /* + * Put the data we've collected down into SRAM + * where ahc_init will find it. + */ + int i; + int max_targ = sc->max_targets & CFMAXTARG; + u_int scsi_conf; + uint16_t discenable; + uint16_t ultraenb; + + discenable = 0; + ultraenb = 0; + if ((sc->adapter_control & CFULTRAEN) != 0) { + /* + * Determine if this adapter has a "newstyle" + * SEEPROM format. + */ + for (i = 0; i < max_targ; i++) { + if ((sc->device_flags[i] & CFSYNCHISULTRA) != 0) { + ahc->flags |= AHC_NEWEEPROM_FMT; + break; + } + } + } + + for (i = 0; i < max_targ; i++) { + u_int scsirate; + uint16_t target_mask; + + target_mask = 0x01 << i; + if (sc->device_flags[i] & CFDISC) + discenable |= target_mask; + if ((ahc->flags & AHC_NEWEEPROM_FMT) != 0) { + if ((sc->device_flags[i] & CFSYNCHISULTRA) != 0) + ultraenb |= target_mask; + } else if ((sc->adapter_control & CFULTRAEN) != 0) { + ultraenb |= target_mask; + } + if ((sc->device_flags[i] & CFXFER) == 0x04 + && (ultraenb & target_mask) != 0) { + /* Treat 10MHz as a non-ultra speed */ + sc->device_flags[i] &= ~CFXFER; + ultraenb &= ~target_mask; + } + if ((ahc->features & AHC_ULTRA2) != 0) { + u_int offset; + + if (sc->device_flags[i] & CFSYNCH) + offset = MAX_OFFSET_ULTRA2; + else + offset = 0; + ahc_outb(ahc, TARG_OFFSET + i, offset); + + /* + * The ultra enable bits contain the + * high bit of the ultra2 sync rate + * field. + */ + scsirate = (sc->device_flags[i] & CFXFER) + | ((ultraenb & target_mask) ? 0x8 : 0x0); + if (sc->device_flags[i] & CFWIDEB) + scsirate |= WIDEXFER; + } else { + scsirate = (sc->device_flags[i] & CFXFER) << 4; + if (sc->device_flags[i] & CFSYNCH) + scsirate |= SOFS; + if (sc->device_flags[i] & CFWIDEB) + scsirate |= WIDEXFER; + } + ahc_outb(ahc, TARG_SCSIRATE + i, scsirate); + } + ahc->our_id = sc->brtime_id & CFSCSIID; + + scsi_conf = (ahc->our_id & 0x7); + if (sc->adapter_control & CFSPARITY) + scsi_conf |= ENSPCHK; + if (sc->adapter_control & CFRESETB) + scsi_conf |= RESET_SCSI; + + ahc->flags |= (sc->adapter_control & CFBOOTCHAN) >> CFBOOTCHANSHIFT; + + if (sc->bios_control & CFEXTEND) + ahc->flags |= AHC_EXTENDED_TRANS_A; + + if (sc->bios_control & CFBIOSEN) + ahc->flags |= AHC_BIOS_ENABLED; + if (ahc->features & AHC_ULTRA + && (ahc->flags & AHC_NEWEEPROM_FMT) == 0) { + /* Should we enable Ultra mode? */ + if (!(sc->adapter_control & CFULTRAEN)) + /* Treat us as a non-ultra card */ + ultraenb = 0; + } + + if (sc->signature == CFSIGNATURE + || sc->signature == CFSIGNATURE2) { + uint32_t devconfig; + + /* Honor the STPWLEVEL settings */ + devconfig = ahc_pci_read_config(ahc->dev_softc, + DEVCONFIG, /*bytes*/4); + devconfig &= ~STPWLEVEL; + if ((sc->bios_control & CFSTPWLEVEL) != 0) + devconfig |= STPWLEVEL; + ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, + devconfig, /*bytes*/4); + } + /* Set SCSICONF info */ + ahc_outb(ahc, SCSICONF, scsi_conf); + ahc_outb(ahc, DISC_DSB, ~(discenable & 0xff)); + ahc_outb(ahc, DISC_DSB + 1, ~((discenable >> 8) & 0xff)); + ahc_outb(ahc, ULTRA_ENB, ultraenb & 0xff); + ahc_outb(ahc, ULTRA_ENB + 1, (ultraenb >> 8) & 0xff); +} + +static void +configure_termination(struct ahc_softc *ahc, + struct seeprom_descriptor *sd, + u_int adapter_control, + u_int *sxfrctl1) +{ + uint8_t brddat; + + brddat = 0; + + /* + * Update the settings in sxfrctl1 to match the + * termination settings + */ + *sxfrctl1 = 0; + + /* + * SEECS must be on for the GALS to latch + * the data properly. Be sure to leave MS + * on or we will release the seeprom. + */ + SEEPROM_OUTB(sd, sd->sd_MS | sd->sd_CS); + if ((adapter_control & CFAUTOTERM) != 0 + || (ahc->features & AHC_NEW_TERMCTL) != 0) { + int internal50_present; + int internal68_present; + int externalcable_present; + int eeprom_present; + int enableSEC_low; + int enableSEC_high; + int enablePRI_low; + int enablePRI_high; + int sum; + + enableSEC_low = 0; + enableSEC_high = 0; + enablePRI_low = 0; + enablePRI_high = 0; + if ((ahc->features & AHC_NEW_TERMCTL) != 0) { + ahc_new_term_detect(ahc, &enableSEC_low, + &enableSEC_high, + &enablePRI_low, + &enablePRI_high, + &eeprom_present); + if ((adapter_control & CFSEAUTOTERM) == 0) { + if (bootverbose) + printk("%s: Manual SE Termination\n", + ahc_name(ahc)); + enableSEC_low = (adapter_control & CFSELOWTERM); + enableSEC_high = + (adapter_control & CFSEHIGHTERM); + } + if ((adapter_control & CFAUTOTERM) == 0) { + if (bootverbose) + printk("%s: Manual LVD Termination\n", + ahc_name(ahc)); + enablePRI_low = (adapter_control & CFSTERM); + enablePRI_high = (adapter_control & CFWSTERM); + } + /* Make the table calculations below happy */ + internal50_present = 0; + internal68_present = 1; + externalcable_present = 1; + } else if ((ahc->features & AHC_SPIOCAP) != 0) { + aic785X_cable_detect(ahc, &internal50_present, + &externalcable_present, + &eeprom_present); + /* Can never support a wide connector. */ + internal68_present = 0; + } else { + aic787X_cable_detect(ahc, &internal50_present, + &internal68_present, + &externalcable_present, + &eeprom_present); + } + + if ((ahc->features & AHC_WIDE) == 0) + internal68_present = 0; + + if (bootverbose + && (ahc->features & AHC_ULTRA2) == 0) { + printk("%s: internal 50 cable %s present", + ahc_name(ahc), + internal50_present ? "is":"not"); + + if ((ahc->features & AHC_WIDE) != 0) + printk(", internal 68 cable %s present", + internal68_present ? "is":"not"); + printk("\n%s: external cable %s present\n", + ahc_name(ahc), + externalcable_present ? "is":"not"); + } + if (bootverbose) + printk("%s: BIOS eeprom %s present\n", + ahc_name(ahc), eeprom_present ? "is" : "not"); + + if ((ahc->flags & AHC_INT50_SPEEDFLEX) != 0) { + /* + * The 50 pin connector is a separate bus, + * so force it to always be terminated. + * In the future, perform current sensing + * to determine if we are in the middle of + * a properly terminated bus. + */ + internal50_present = 0; + } + + /* + * Now set the termination based on what + * we found. + * Flash Enable = BRDDAT7 + * Secondary High Term Enable = BRDDAT6 + * Secondary Low Term Enable = BRDDAT5 (7890) + * Primary High Term Enable = BRDDAT4 (7890) + */ + if ((ahc->features & AHC_ULTRA2) == 0 + && (internal50_present != 0) + && (internal68_present != 0) + && (externalcable_present != 0)) { + printk("%s: Illegal cable configuration!!. " + "Only two connectors on the " + "adapter may be used at a " + "time!\n", ahc_name(ahc)); + + /* + * Pretend there are no cables in the hope + * that having all of the termination on + * gives us a more stable bus. + */ + internal50_present = 0; + internal68_present = 0; + externalcable_present = 0; + } + + if ((ahc->features & AHC_WIDE) != 0 + && ((externalcable_present == 0) + || (internal68_present == 0) + || (enableSEC_high != 0))) { + brddat |= BRDDAT6; + if (bootverbose) { + if ((ahc->flags & AHC_INT50_SPEEDFLEX) != 0) + printk("%s: 68 pin termination " + "Enabled\n", ahc_name(ahc)); + else + printk("%s: %sHigh byte termination " + "Enabled\n", ahc_name(ahc), + enableSEC_high ? "Secondary " + : ""); + } + } + + sum = internal50_present + internal68_present + + externalcable_present; + if (sum < 2 || (enableSEC_low != 0)) { + if ((ahc->features & AHC_ULTRA2) != 0) + brddat |= BRDDAT5; + else + *sxfrctl1 |= STPWEN; + if (bootverbose) { + if ((ahc->flags & AHC_INT50_SPEEDFLEX) != 0) + printk("%s: 50 pin termination " + "Enabled\n", ahc_name(ahc)); + else + printk("%s: %sLow byte termination " + "Enabled\n", ahc_name(ahc), + enableSEC_low ? "Secondary " + : ""); + } + } + + if (enablePRI_low != 0) { + *sxfrctl1 |= STPWEN; + if (bootverbose) + printk("%s: Primary Low Byte termination " + "Enabled\n", ahc_name(ahc)); + } + + /* + * Setup STPWEN before setting up the rest of + * the termination per the tech note on the U160 cards. + */ + ahc_outb(ahc, SXFRCTL1, *sxfrctl1); + + if (enablePRI_high != 0) { + brddat |= BRDDAT4; + if (bootverbose) + printk("%s: Primary High Byte " + "termination Enabled\n", + ahc_name(ahc)); + } + + write_brdctl(ahc, brddat); + + } else { + if ((adapter_control & CFSTERM) != 0) { + *sxfrctl1 |= STPWEN; + + if (bootverbose) + printk("%s: %sLow byte termination Enabled\n", + ahc_name(ahc), + (ahc->features & AHC_ULTRA2) ? "Primary " + : ""); + } + + if ((adapter_control & CFWSTERM) != 0 + && (ahc->features & AHC_WIDE) != 0) { + brddat |= BRDDAT6; + if (bootverbose) + printk("%s: %sHigh byte termination Enabled\n", + ahc_name(ahc), + (ahc->features & AHC_ULTRA2) + ? "Secondary " : ""); + } + + /* + * Setup STPWEN before setting up the rest of + * the termination per the tech note on the U160 cards. + */ + ahc_outb(ahc, SXFRCTL1, *sxfrctl1); + + if ((ahc->features & AHC_WIDE) != 0) + write_brdctl(ahc, brddat); + } + SEEPROM_OUTB(sd, sd->sd_MS); /* Clear CS */ +} + +static void +ahc_new_term_detect(struct ahc_softc *ahc, int *enableSEC_low, + int *enableSEC_high, int *enablePRI_low, + int *enablePRI_high, int *eeprom_present) +{ + uint8_t brdctl; + + /* + * BRDDAT7 = Eeprom + * BRDDAT6 = Enable Secondary High Byte termination + * BRDDAT5 = Enable Secondary Low Byte termination + * BRDDAT4 = Enable Primary high byte termination + * BRDDAT3 = Enable Primary low byte termination + */ + brdctl = read_brdctl(ahc); + *eeprom_present = brdctl & BRDDAT7; + *enableSEC_high = (brdctl & BRDDAT6); + *enableSEC_low = (brdctl & BRDDAT5); + *enablePRI_high = (brdctl & BRDDAT4); + *enablePRI_low = (brdctl & BRDDAT3); +} + +static void +aic787X_cable_detect(struct ahc_softc *ahc, int *internal50_present, + int *internal68_present, int *externalcable_present, + int *eeprom_present) +{ + uint8_t brdctl; + + /* + * First read the status of our cables. + * Set the rom bank to 0 since the + * bank setting serves as a multiplexor + * for the cable detection logic. + * BRDDAT5 controls the bank switch. + */ + write_brdctl(ahc, 0); + + /* + * Now read the state of the internal + * connectors. BRDDAT6 is INT50 and + * BRDDAT7 is INT68. + */ + brdctl = read_brdctl(ahc); + *internal50_present = (brdctl & BRDDAT6) ? 0 : 1; + *internal68_present = (brdctl & BRDDAT7) ? 0 : 1; + + /* + * Set the rom bank to 1 and determine + * the other signals. + */ + write_brdctl(ahc, BRDDAT5); + + /* + * Now read the state of the external + * connectors. BRDDAT6 is EXT68 and + * BRDDAT7 is EPROMPS. + */ + brdctl = read_brdctl(ahc); + *externalcable_present = (brdctl & BRDDAT6) ? 0 : 1; + *eeprom_present = (brdctl & BRDDAT7) ? 1 : 0; +} + +static void +aic785X_cable_detect(struct ahc_softc *ahc, int *internal50_present, + int *externalcable_present, int *eeprom_present) +{ + uint8_t brdctl; + uint8_t spiocap; + + spiocap = ahc_inb(ahc, SPIOCAP); + spiocap &= ~SOFTCMDEN; + spiocap |= EXT_BRDCTL; + ahc_outb(ahc, SPIOCAP, spiocap); + ahc_outb(ahc, BRDCTL, BRDRW|BRDCS); + ahc_flush_device_writes(ahc); + ahc_delay(500); + ahc_outb(ahc, BRDCTL, 0); + ahc_flush_device_writes(ahc); + ahc_delay(500); + brdctl = ahc_inb(ahc, BRDCTL); + *internal50_present = (brdctl & BRDDAT5) ? 0 : 1; + *externalcable_present = (brdctl & BRDDAT6) ? 0 : 1; + *eeprom_present = (ahc_inb(ahc, SPIOCAP) & EEPROM) ? 1 : 0; +} + +int +ahc_acquire_seeprom(struct ahc_softc *ahc, struct seeprom_descriptor *sd) +{ + int wait; + + if ((ahc->features & AHC_SPIOCAP) != 0 + && (ahc_inb(ahc, SPIOCAP) & SEEPROM) == 0) + return (0); + + /* + * Request access of the memory port. When access is + * granted, SEERDY will go high. We use a 1 second + * timeout which should be near 1 second more than + * is needed. Reason: after the chip reset, there + * should be no contention. + */ + SEEPROM_OUTB(sd, sd->sd_MS); + wait = 1000; /* 1 second timeout in msec */ + while (--wait && ((SEEPROM_STATUS_INB(sd) & sd->sd_RDY) == 0)) { + ahc_delay(1000); /* delay 1 msec */ + } + if ((SEEPROM_STATUS_INB(sd) & sd->sd_RDY) == 0) { + SEEPROM_OUTB(sd, 0); + return (0); + } + return(1); +} + +void +ahc_release_seeprom(struct seeprom_descriptor *sd) +{ + /* Release access to the memory port and the serial EEPROM. */ + SEEPROM_OUTB(sd, 0); +} + +static void +write_brdctl(struct ahc_softc *ahc, uint8_t value) +{ + uint8_t brdctl; + + if ((ahc->chip & AHC_CHIPID_MASK) == AHC_AIC7895) { + brdctl = BRDSTB; + if (ahc->channel == 'B') + brdctl |= BRDCS; + } else if ((ahc->features & AHC_ULTRA2) != 0) { + brdctl = 0; + } else { + brdctl = BRDSTB|BRDCS; + } + ahc_outb(ahc, BRDCTL, brdctl); + ahc_flush_device_writes(ahc); + brdctl |= value; + ahc_outb(ahc, BRDCTL, brdctl); + ahc_flush_device_writes(ahc); + if ((ahc->features & AHC_ULTRA2) != 0) + brdctl |= BRDSTB_ULTRA2; + else + brdctl &= ~BRDSTB; + ahc_outb(ahc, BRDCTL, brdctl); + ahc_flush_device_writes(ahc); + if ((ahc->features & AHC_ULTRA2) != 0) + brdctl = 0; + else + brdctl &= ~BRDCS; + ahc_outb(ahc, BRDCTL, brdctl); +} + +static uint8_t +read_brdctl(struct ahc_softc *ahc) +{ + uint8_t brdctl; + uint8_t value; + + if ((ahc->chip & AHC_CHIPID_MASK) == AHC_AIC7895) { + brdctl = BRDRW; + if (ahc->channel == 'B') + brdctl |= BRDCS; + } else if ((ahc->features & AHC_ULTRA2) != 0) { + brdctl = BRDRW_ULTRA2; + } else { + brdctl = BRDRW|BRDCS; + } + ahc_outb(ahc, BRDCTL, brdctl); + ahc_flush_device_writes(ahc); + value = ahc_inb(ahc, BRDCTL); + ahc_outb(ahc, BRDCTL, 0); + return (value); +} + +static void +ahc_pci_intr(struct ahc_softc *ahc) +{ + u_int error; + u_int status1; + + error = ahc_inb(ahc, ERROR); + if ((error & PCIERRSTAT) == 0) + return; + + status1 = ahc_pci_read_config(ahc->dev_softc, + PCIR_STATUS + 1, /*bytes*/1); + + printk("%s: PCI error Interrupt at seqaddr = 0x%x\n", + ahc_name(ahc), + ahc_inb(ahc, SEQADDR0) | (ahc_inb(ahc, SEQADDR1) << 8)); + + if (status1 & DPE) { + ahc->pci_target_perr_count++; + printk("%s: Data Parity Error Detected during address " + "or write data phase\n", ahc_name(ahc)); + } + if (status1 & SSE) { + printk("%s: Signal System Error Detected\n", ahc_name(ahc)); + } + if (status1 & RMA) { + printk("%s: Received a Master Abort\n", ahc_name(ahc)); + } + if (status1 & RTA) { + printk("%s: Received a Target Abort\n", ahc_name(ahc)); + } + if (status1 & STA) { + printk("%s: Signaled a Target Abort\n", ahc_name(ahc)); + } + if (status1 & DPR) { + printk("%s: Data Parity Error has been reported via PERR#\n", + ahc_name(ahc)); + } + + /* Clear latched errors. */ + ahc_pci_write_config(ahc->dev_softc, PCIR_STATUS + 1, + status1, /*bytes*/1); + + if ((status1 & (DPE|SSE|RMA|RTA|STA|DPR)) == 0) { + printk("%s: Latched PCIERR interrupt with " + "no status bits set\n", ahc_name(ahc)); + } else { + ahc_outb(ahc, CLRINT, CLRPARERR); + } + + if (ahc->pci_target_perr_count > AHC_PCI_TARGET_PERR_THRESH) { + printk( +"%s: WARNING WARNING WARNING WARNING\n" +"%s: Too many PCI parity errors observed as a target.\n" +"%s: Some device on this bus is generating bad parity.\n" +"%s: This is an error *observed by*, not *generated by*, this controller.\n" +"%s: PCI parity error checking has been disabled.\n" +"%s: WARNING WARNING WARNING WARNING\n", + ahc_name(ahc), ahc_name(ahc), ahc_name(ahc), + ahc_name(ahc), ahc_name(ahc), ahc_name(ahc)); + ahc->seqctl |= FAILDIS; + ahc_outb(ahc, SEQCTL, ahc->seqctl); + } + ahc_unpause(ahc); +} + +static int +ahc_pci_chip_init(struct ahc_softc *ahc) +{ + ahc_outb(ahc, DSCOMMAND0, ahc->bus_softc.pci_softc.dscommand0); + ahc_outb(ahc, DSPCISTATUS, ahc->bus_softc.pci_softc.dspcistatus); + if ((ahc->features & AHC_DT) != 0) { + u_int sfunct; + + sfunct = ahc_inb(ahc, SFUNCT) & ~ALT_MODE; + ahc_outb(ahc, SFUNCT, sfunct | ALT_MODE); + ahc_outb(ahc, OPTIONMODE, ahc->bus_softc.pci_softc.optionmode); + ahc_outw(ahc, TARGCRCCNT, ahc->bus_softc.pci_softc.targcrccnt); + ahc_outb(ahc, SFUNCT, sfunct); + ahc_outb(ahc, CRCCONTROL1, + ahc->bus_softc.pci_softc.crccontrol1); + } + if ((ahc->features & AHC_MULTI_FUNC) != 0) + ahc_outb(ahc, SCBBADDR, ahc->bus_softc.pci_softc.scbbaddr); + + if ((ahc->features & AHC_ULTRA2) != 0) + ahc_outb(ahc, DFF_THRSH, ahc->bus_softc.pci_softc.dff_thrsh); + + return (ahc_chip_init(ahc)); +} + +#ifdef CONFIG_PM +void +ahc_pci_resume(struct ahc_softc *ahc) +{ + /* + * We assume that the OS has restored our register + * mappings, etc. Just update the config space registers + * that the OS doesn't know about and rely on our chip + * reset handler to handle the rest. + */ + ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, + ahc->bus_softc.pci_softc.devconfig, /*bytes*/4); + ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, + ahc->bus_softc.pci_softc.command, /*bytes*/1); + ahc_pci_write_config(ahc->dev_softc, CSIZE_LATTIME, + ahc->bus_softc.pci_softc.csize_lattime, /*bytes*/1); + if ((ahc->flags & AHC_HAS_TERM_LOGIC) != 0) { + struct seeprom_descriptor sd; + u_int sxfrctl1; + + sd.sd_ahc = ahc; + sd.sd_control_offset = SEECTL; + sd.sd_status_offset = SEECTL; + sd.sd_dataout_offset = SEECTL; + + ahc_acquire_seeprom(ahc, &sd); + configure_termination(ahc, &sd, + ahc->seep_config->adapter_control, + &sxfrctl1); + ahc_release_seeprom(&sd); + } +} +#endif + +static int +ahc_aic785X_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + uint8_t rev; + + pci = ahc->dev_softc; + ahc->channel = 'A'; + ahc->chip = AHC_AIC7850; + ahc->features = AHC_AIC7850_FE; + ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG; + rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1); + if (rev >= 1) + ahc->bugs |= AHC_PCI_2_1_RETRY_BUG; + ahc->instruction_ram_size = 512; + return (0); +} + +static int +ahc_aic7860_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + uint8_t rev; + + pci = ahc->dev_softc; + ahc->channel = 'A'; + ahc->chip = AHC_AIC7860; + ahc->features = AHC_AIC7860_FE; + ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG; + rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1); + if (rev >= 1) + ahc->bugs |= AHC_PCI_2_1_RETRY_BUG; + ahc->instruction_ram_size = 512; + return (0); +} + +static int +ahc_apa1480_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7860_setup(ahc); + if (error != 0) + return (error); + ahc->features |= AHC_REMOVABLE; + return (0); +} + +static int +ahc_aic7870_setup(struct ahc_softc *ahc) +{ + + ahc->channel = 'A'; + ahc->chip = AHC_AIC7870; + ahc->features = AHC_AIC7870_FE; + ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG; + ahc->instruction_ram_size = 512; + return (0); +} + +static int +ahc_aic7870h_setup(struct ahc_softc *ahc) +{ + int error = ahc_aic7870_setup(ahc); + + ahc->features |= AHC_HVD; + + return error; +} + +static int +ahc_aha394X_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7870_setup(ahc); + if (error == 0) + error = ahc_aha394XX_setup(ahc); + return (error); +} + +static int +ahc_aha394Xh_setup(struct ahc_softc *ahc) +{ + int error = ahc_aha394X_setup(ahc); + + ahc->features |= AHC_HVD; + + return error; +} + +static int +ahc_aha398X_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7870_setup(ahc); + if (error == 0) + error = ahc_aha398XX_setup(ahc); + return (error); +} + +static int +ahc_aha494X_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7870_setup(ahc); + if (error == 0) + error = ahc_aha494XX_setup(ahc); + return (error); +} + +static int +ahc_aha494Xh_setup(struct ahc_softc *ahc) +{ + int error = ahc_aha494X_setup(ahc); + + ahc->features |= AHC_HVD; + + return error; +} + +static int +ahc_aic7880_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + uint8_t rev; + + pci = ahc->dev_softc; + ahc->channel = 'A'; + ahc->chip = AHC_AIC7880; + ahc->features = AHC_AIC7880_FE; + ahc->bugs |= AHC_TMODE_WIDEODD_BUG; + rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1); + if (rev >= 1) { + ahc->bugs |= AHC_PCI_2_1_RETRY_BUG; + } else { + ahc->bugs |= AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG; + } + ahc->instruction_ram_size = 512; + return (0); +} + +static int +ahc_aic7880h_setup(struct ahc_softc *ahc) +{ + int error = ahc_aic7880_setup(ahc); + + ahc->features |= AHC_HVD; + + return error; +} + + +static int +ahc_aha2940Pro_setup(struct ahc_softc *ahc) +{ + + ahc->flags |= AHC_INT50_SPEEDFLEX; + return (ahc_aic7880_setup(ahc)); +} + +static int +ahc_aha394XU_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7880_setup(ahc); + if (error == 0) + error = ahc_aha394XX_setup(ahc); + return (error); +} + +static int +ahc_aha394XUh_setup(struct ahc_softc *ahc) +{ + int error = ahc_aha394XU_setup(ahc); + + ahc->features |= AHC_HVD; + + return error; +} + +static int +ahc_aha398XU_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7880_setup(ahc); + if (error == 0) + error = ahc_aha398XX_setup(ahc); + return (error); +} + +static int +ahc_aic7890_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + uint8_t rev; + + pci = ahc->dev_softc; + ahc->channel = 'A'; + ahc->chip = AHC_AIC7890; + ahc->features = AHC_AIC7890_FE; + ahc->flags |= AHC_NEWEEPROM_FMT; + rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1); + if (rev == 0) + ahc->bugs |= AHC_AUTOFLUSH_BUG|AHC_CACHETHEN_BUG; + ahc->instruction_ram_size = 768; + return (0); +} + +static int +ahc_aic7892_setup(struct ahc_softc *ahc) +{ + + ahc->channel = 'A'; + ahc->chip = AHC_AIC7892; + ahc->features = AHC_AIC7892_FE; + ahc->flags |= AHC_NEWEEPROM_FMT; + ahc->bugs |= AHC_SCBCHAN_UPLOAD_BUG; + ahc->instruction_ram_size = 1024; + return (0); +} + +static int +ahc_aic7895_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + uint8_t rev; + + pci = ahc->dev_softc; + ahc->channel = ahc_get_pci_function(pci) == 1 ? 'B' : 'A'; + /* + * The 'C' revision of the aic7895 has a few additional features. + */ + rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1); + if (rev >= 4) { + ahc->chip = AHC_AIC7895C; + ahc->features = AHC_AIC7895C_FE; + } else { + u_int command; + + ahc->chip = AHC_AIC7895; + ahc->features = AHC_AIC7895_FE; + + /* + * The BIOS disables the use of MWI transactions + * since it does not have the MWI bug work around + * we have. Disabling MWI reduces performance, so + * turn it on again. + */ + command = ahc_pci_read_config(pci, PCIR_COMMAND, /*bytes*/1); + command |= PCIM_CMD_MWRICEN; + ahc_pci_write_config(pci, PCIR_COMMAND, command, /*bytes*/1); + ahc->bugs |= AHC_PCI_MWI_BUG; + } + /* + * XXX Does CACHETHEN really not work??? What about PCI retry? + * on C level chips. Need to test, but for now, play it safe. + */ + ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_PCI_2_1_RETRY_BUG + | AHC_CACHETHEN_BUG; + +#if 0 + uint32_t devconfig; + + /* + * Cachesize must also be zero due to stray DAC + * problem when sitting behind some bridges. + */ + ahc_pci_write_config(pci, CSIZE_LATTIME, 0, /*bytes*/1); + devconfig = ahc_pci_read_config(pci, DEVCONFIG, /*bytes*/1); + devconfig |= MRDCEN; + ahc_pci_write_config(pci, DEVCONFIG, devconfig, /*bytes*/1); +#endif + ahc->flags |= AHC_NEWEEPROM_FMT; + ahc->instruction_ram_size = 512; + return (0); +} + +static int +ahc_aic7895h_setup(struct ahc_softc *ahc) +{ + int error = ahc_aic7895_setup(ahc); + + ahc->features |= AHC_HVD; + + return error; +} + +static int +ahc_aic7896_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + + pci = ahc->dev_softc; + ahc->channel = ahc_get_pci_function(pci) == 1 ? 'B' : 'A'; + ahc->chip = AHC_AIC7896; + ahc->features = AHC_AIC7896_FE; + ahc->flags |= AHC_NEWEEPROM_FMT; + ahc->bugs |= AHC_CACHETHEN_DIS_BUG; + ahc->instruction_ram_size = 768; + return (0); +} + +static int +ahc_aic7899_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + + pci = ahc->dev_softc; + ahc->channel = ahc_get_pci_function(pci) == 1 ? 'B' : 'A'; + ahc->chip = AHC_AIC7899; + ahc->features = AHC_AIC7899_FE; + ahc->flags |= AHC_NEWEEPROM_FMT; + ahc->bugs |= AHC_SCBCHAN_UPLOAD_BUG; + ahc->instruction_ram_size = 1024; + return (0); +} + +static int +ahc_aha29160C_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7899_setup(ahc); + if (error != 0) + return (error); + ahc->features |= AHC_REMOVABLE; + return (0); +} + +static int +ahc_raid_setup(struct ahc_softc *ahc) +{ + printk("RAID functionality unsupported\n"); + return (ENXIO); +} + +static int +ahc_aha394XX_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + + pci = ahc->dev_softc; + switch (ahc_get_pci_slot(pci)) { + case AHC_394X_SLOT_CHANNEL_A: + ahc->channel = 'A'; + break; + case AHC_394X_SLOT_CHANNEL_B: + ahc->channel = 'B'; + break; + default: + printk("adapter at unexpected slot %d\n" + "unable to map to a channel\n", + ahc_get_pci_slot(pci)); + ahc->channel = 'A'; + } + return (0); +} + +static int +ahc_aha398XX_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + + pci = ahc->dev_softc; + switch (ahc_get_pci_slot(pci)) { + case AHC_398X_SLOT_CHANNEL_A: + ahc->channel = 'A'; + break; + case AHC_398X_SLOT_CHANNEL_B: + ahc->channel = 'B'; + break; + case AHC_398X_SLOT_CHANNEL_C: + ahc->channel = 'C'; + break; + default: + printk("adapter at unexpected slot %d\n" + "unable to map to a channel\n", + ahc_get_pci_slot(pci)); + ahc->channel = 'A'; + break; + } + ahc->flags |= AHC_LARGE_SEEPROM; + return (0); +} + +static int +ahc_aha494XX_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + + pci = ahc->dev_softc; + switch (ahc_get_pci_slot(pci)) { + case AHC_494X_SLOT_CHANNEL_A: + ahc->channel = 'A'; + break; + case AHC_494X_SLOT_CHANNEL_B: + ahc->channel = 'B'; + break; + case AHC_494X_SLOT_CHANNEL_C: + ahc->channel = 'C'; + break; + case AHC_494X_SLOT_CHANNEL_D: + ahc->channel = 'D'; + break; + default: + printk("adapter at unexpected slot %d\n" + "unable to map to a channel\n", + ahc_get_pci_slot(pci)); + ahc->channel = 'A'; + } + ahc->flags |= AHC_LARGE_SEEPROM; + return (0); +} diff --git a/drivers/scsi/aic7xxx/aic7xxx_pci.h b/drivers/scsi/aic7xxx/aic7xxx_pci.h new file mode 100644 index 000000000..263f85da4 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx_pci.h @@ -0,0 +1,125 @@ +/* + * Adaptec AIC7xxx device driver for Linux. + * + * Copyright (c) 2000-2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id$ + * + */ +#ifndef _AIC7XXX_PCI_H_ +#define _AIC7XXX_PCI_H_ + +#define ID_ALL_MASK 0xFFFFFFFFFFFFFFFFull +#define ID_DEV_VENDOR_MASK 0xFFFFFFFF00000000ull +#define ID_9005_GENERIC_MASK 0xFFF0FFFF00000000ull +#define ID_9005_SISL_MASK 0x000FFFFF00000000ull +#define ID_9005_SISL_ID 0x0005900500000000ull +#define ID_AIC7850 0x5078900400000000ull +#define ID_AHA_2902_04_10_15_20C_30C 0x5078900478509004ull +#define ID_AIC7855 0x5578900400000000ull +#define ID_AIC7859 0x3860900400000000ull +#define ID_AHA_2930CU 0x3860900438699004ull +#define ID_AIC7860 0x6078900400000000ull +#define ID_AIC7860C 0x6078900478609004ull +#define ID_AHA_1480A 0x6075900400000000ull +#define ID_AHA_2940AU_0 0x6178900400000000ull +#define ID_AHA_2940AU_1 0x6178900478619004ull +#define ID_AHA_2940AU_CN 0x2178900478219004ull +#define ID_AHA_2930C_VAR 0x6038900438689004ull + +#define ID_AIC7870 0x7078900400000000ull +#define ID_AHA_2940 0x7178900400000000ull +#define ID_AHA_3940 0x7278900400000000ull +#define ID_AHA_398X 0x7378900400000000ull +#define ID_AHA_2944 0x7478900400000000ull +#define ID_AHA_3944 0x7578900400000000ull +#define ID_AHA_4944 0x7678900400000000ull + +#define ID_AIC7880 0x8078900400000000ull +#define ID_AIC7880_B 0x8078900478809004ull +#define ID_AHA_2940U 0x8178900400000000ull +#define ID_AHA_3940U 0x8278900400000000ull +#define ID_AHA_2944U 0x8478900400000000ull +#define ID_AHA_3944U 0x8578900400000000ull +#define ID_AHA_398XU 0x8378900400000000ull +#define ID_AHA_4944U 0x8678900400000000ull +#define ID_AHA_2940UB 0x8178900478819004ull +#define ID_AHA_2930U 0x8878900478889004ull +#define ID_AHA_2940U_PRO 0x8778900478879004ull +#define ID_AHA_2940U_CN 0x0078900478009004ull + +#define ID_AIC7895 0x7895900478959004ull +#define ID_AIC7895_ARO 0x7890900478939004ull +#define ID_AIC7895_ARO_MASK 0xFFF0FFFFFFFFFFFFull +#define ID_AHA_2940U_DUAL 0x7895900478919004ull +#define ID_AHA_3940AU 0x7895900478929004ull +#define ID_AHA_3944AU 0x7895900478949004ull + +#define ID_AIC7890 0x001F9005000F9005ull +#define ID_AIC7890_ARO 0x00139005000F9005ull +#define ID_AAA_131U2 0x0013900500039005ull +#define ID_AHA_2930U2 0x0011900501819005ull +#define ID_AHA_2940U2B 0x00109005A1009005ull +#define ID_AHA_2940U2_OEM 0x0010900521809005ull +#define ID_AHA_2940U2 0x00109005A1809005ull +#define ID_AHA_2950U2B 0x00109005E1009005ull + +#define ID_AIC7892 0x008F9005FFFF9005ull +#define ID_AIC7892_ARO 0x00839005FFFF9005ull +#define ID_AHA_29160 0x00809005E2A09005ull +#define ID_AHA_29160_CPQ 0x00809005E2A00E11ull +#define ID_AHA_29160N 0x0080900562A09005ull +#define ID_AHA_29160C 0x0080900562209005ull +#define ID_AHA_29160B 0x00809005E2209005ull +#define ID_AHA_19160B 0x0081900562A19005ull +#define ID_AHA_2915_30LP 0x0082900502109005ull + +#define ID_AIC7896 0x005F9005FFFF9005ull +#define ID_AIC7896_ARO 0x00539005FFFF9005ull +#define ID_AHA_3950U2B_0 0x00509005FFFF9005ull +#define ID_AHA_3950U2B_1 0x00509005F5009005ull +#define ID_AHA_3950U2D_0 0x00519005FFFF9005ull +#define ID_AHA_3950U2D_1 0x00519005B5009005ull + +#define ID_AIC7899 0x00CF9005FFFF9005ull +#define ID_AIC7899_ARO 0x00C39005FFFF9005ull +#define ID_AHA_3960D 0x00C09005F6209005ull +#define ID_AHA_3960D_CPQ 0x00C09005F6200E11ull + +#define ID_AIC7810 0x1078900400000000ull +#define ID_AIC7815 0x7815900400000000ull + +#endif /* _AIC7XXX_PCI_H_ */ diff --git a/drivers/scsi/aic7xxx/aic7xxx_proc.c b/drivers/scsi/aic7xxx/aic7xxx_proc.c new file mode 100644 index 000000000..18459605d --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx_proc.c @@ -0,0 +1,342 @@ +/* + * Copyright (c) 2000-2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * String handling code courtesy of Gerard Roudier's <groudier@club-internet.fr> + * sym driver. + * + * $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic7xxx_proc.c#29 $ + */ +#include "aic7xxx_osm.h" +#include "aic7xxx_inline.h" +#include "aic7xxx_93cx6.h" + +static void ahc_dump_target_state(struct ahc_softc *ahc, + struct seq_file *m, + u_int our_id, char channel, + u_int target_id, u_int target_offset); +static void ahc_dump_device_state(struct seq_file *m, + struct scsi_device *dev); + +/* + * Table of syncrates that don't follow the "divisible by 4" + * rule. This table will be expanded in future SCSI specs. + */ +static const struct { + u_int period_factor; + u_int period; /* in 100ths of ns */ +} scsi_syncrates[] = { + { 0x08, 625 }, /* FAST-160 */ + { 0x09, 1250 }, /* FAST-80 */ + { 0x0a, 2500 }, /* FAST-40 40MHz */ + { 0x0b, 3030 }, /* FAST-40 33MHz */ + { 0x0c, 5000 } /* FAST-20 */ +}; + +/* + * Return the frequency in kHz corresponding to the given + * sync period factor. + */ +static u_int +ahc_calc_syncsrate(u_int period_factor) +{ + int i; + + /* See if the period is in the "exception" table */ + for (i = 0; i < ARRAY_SIZE(scsi_syncrates); i++) { + + if (period_factor == scsi_syncrates[i].period_factor) { + /* Period in kHz */ + return (100000000 / scsi_syncrates[i].period); + } + } + + /* + * Wasn't in the table, so use the standard + * 4 times conversion. + */ + return (10000000 / (period_factor * 4 * 10)); +} + +static void +ahc_format_transinfo(struct seq_file *m, struct ahc_transinfo *tinfo) +{ + u_int speed; + u_int freq; + u_int mb; + + speed = 3300; + freq = 0; + if (tinfo->offset != 0) { + freq = ahc_calc_syncsrate(tinfo->period); + speed = freq; + } + speed *= (0x01 << tinfo->width); + mb = speed / 1000; + if (mb > 0) + seq_printf(m, "%d.%03dMB/s transfers", mb, speed % 1000); + else + seq_printf(m, "%dKB/s transfers", speed); + + if (freq != 0) { + seq_printf(m, " (%d.%03dMHz%s, offset %d", + freq / 1000, freq % 1000, + (tinfo->ppr_options & MSG_EXT_PPR_DT_REQ) != 0 + ? " DT" : "", tinfo->offset); + } + + if (tinfo->width > 0) { + if (freq != 0) { + seq_puts(m, ", "); + } else { + seq_puts(m, " ("); + } + seq_printf(m, "%dbit)", 8 * (0x01 << tinfo->width)); + } else if (freq != 0) { + seq_putc(m, ')'); + } + seq_putc(m, '\n'); +} + +static void +ahc_dump_target_state(struct ahc_softc *ahc, struct seq_file *m, + u_int our_id, char channel, u_int target_id, + u_int target_offset) +{ + struct scsi_target *starget; + struct ahc_initiator_tinfo *tinfo; + struct ahc_tmode_tstate *tstate; + int lun; + + tinfo = ahc_fetch_transinfo(ahc, channel, our_id, + target_id, &tstate); + if ((ahc->features & AHC_TWIN) != 0) + seq_printf(m, "Channel %c ", channel); + seq_printf(m, "Target %d Negotiation Settings\n", target_id); + seq_puts(m, "\tUser: "); + ahc_format_transinfo(m, &tinfo->user); + starget = ahc->platform_data->starget[target_offset]; + if (!starget) + return; + + seq_puts(m, "\tGoal: "); + ahc_format_transinfo(m, &tinfo->goal); + seq_puts(m, "\tCurr: "); + ahc_format_transinfo(m, &tinfo->curr); + + for (lun = 0; lun < AHC_NUM_LUNS; lun++) { + struct scsi_device *sdev; + + sdev = scsi_device_lookup_by_target(starget, lun); + + if (sdev == NULL) + continue; + + ahc_dump_device_state(m, sdev); + } +} + +static void +ahc_dump_device_state(struct seq_file *m, struct scsi_device *sdev) +{ + struct ahc_linux_device *dev = scsi_transport_device_data(sdev); + + seq_printf(m, "\tChannel %c Target %d Lun %d Settings\n", + sdev->sdev_target->channel + 'A', + sdev->sdev_target->id, (u8)sdev->lun); + + seq_printf(m, "\t\tCommands Queued %ld\n", dev->commands_issued); + seq_printf(m, "\t\tCommands Active %d\n", dev->active); + seq_printf(m, "\t\tCommand Openings %d\n", dev->openings); + seq_printf(m, "\t\tMax Tagged Openings %d\n", dev->maxtags); + seq_printf(m, "\t\tDevice Queue Frozen Count %d\n", dev->qfrozen); +} + +int +ahc_proc_write_seeprom(struct Scsi_Host *shost, char *buffer, int length) +{ + struct ahc_softc *ahc = *(struct ahc_softc **)shost->hostdata; + struct seeprom_descriptor sd; + int have_seeprom; + u_long s; + int paused; + int written; + + /* Default to failure. */ + written = -EINVAL; + ahc_lock(ahc, &s); + paused = ahc_is_paused(ahc); + if (!paused) + ahc_pause(ahc); + + if (length != sizeof(struct seeprom_config)) { + printk("ahc_proc_write_seeprom: incorrect buffer size\n"); + goto done; + } + + have_seeprom = ahc_verify_cksum((struct seeprom_config*)buffer); + if (have_seeprom == 0) { + printk("ahc_proc_write_seeprom: cksum verification failed\n"); + goto done; + } + + sd.sd_ahc = ahc; +#if AHC_PCI_CONFIG > 0 + if ((ahc->chip & AHC_PCI) != 0) { + sd.sd_control_offset = SEECTL; + sd.sd_status_offset = SEECTL; + sd.sd_dataout_offset = SEECTL; + if (ahc->flags & AHC_LARGE_SEEPROM) + sd.sd_chip = C56_66; + else + sd.sd_chip = C46; + sd.sd_MS = SEEMS; + sd.sd_RDY = SEERDY; + sd.sd_CS = SEECS; + sd.sd_CK = SEECK; + sd.sd_DO = SEEDO; + sd.sd_DI = SEEDI; + have_seeprom = ahc_acquire_seeprom(ahc, &sd); + } else +#endif + if ((ahc->chip & AHC_VL) != 0) { + sd.sd_control_offset = SEECTL_2840; + sd.sd_status_offset = STATUS_2840; + sd.sd_dataout_offset = STATUS_2840; + sd.sd_chip = C46; + sd.sd_MS = 0; + sd.sd_RDY = EEPROM_TF; + sd.sd_CS = CS_2840; + sd.sd_CK = CK_2840; + sd.sd_DO = DO_2840; + sd.sd_DI = DI_2840; + have_seeprom = TRUE; + } else { + printk("ahc_proc_write_seeprom: unsupported adapter type\n"); + goto done; + } + + if (!have_seeprom) { + printk("ahc_proc_write_seeprom: No Serial EEPROM\n"); + goto done; + } else { + u_int start_addr; + + if (ahc->seep_config == NULL) { + ahc->seep_config = kmalloc(sizeof(*ahc->seep_config), GFP_ATOMIC); + if (ahc->seep_config == NULL) { + printk("aic7xxx: Unable to allocate serial " + "eeprom buffer. Write failing\n"); + goto done; + } + } + printk("aic7xxx: Writing Serial EEPROM\n"); + start_addr = 32 * (ahc->channel - 'A'); + ahc_write_seeprom(&sd, (u_int16_t *)buffer, start_addr, + sizeof(struct seeprom_config)/2); + ahc_read_seeprom(&sd, (uint16_t *)ahc->seep_config, + start_addr, sizeof(struct seeprom_config)/2); +#if AHC_PCI_CONFIG > 0 + if ((ahc->chip & AHC_VL) == 0) + ahc_release_seeprom(&sd); +#endif + written = length; + } + +done: + if (!paused) + ahc_unpause(ahc); + ahc_unlock(ahc, &s); + return (written); +} + +/* + * Return information to handle /proc support for the driver. + */ +int +ahc_linux_show_info(struct seq_file *m, struct Scsi_Host *shost) +{ + struct ahc_softc *ahc = *(struct ahc_softc **)shost->hostdata; + char ahc_info[256]; + u_int max_targ; + u_int i; + + seq_printf(m, "Adaptec AIC7xxx driver version: %s\n", + AIC7XXX_DRIVER_VERSION); + seq_printf(m, "%s\n", ahc->description); + ahc_controller_info(ahc, ahc_info); + seq_printf(m, "%s\n", ahc_info); + seq_printf(m, "Allocated SCBs: %d, SG List Length: %d\n\n", + ahc->scb_data->numscbs, AHC_NSEG); + + + if (ahc->seep_config == NULL) + seq_puts(m, "No Serial EEPROM\n"); + else { + seq_puts(m, "Serial EEPROM:\n"); + for (i = 0; i < sizeof(*ahc->seep_config)/2; i++) { + if (((i % 8) == 0) && (i != 0)) { + seq_putc(m, '\n'); + } + seq_printf(m, "0x%.4x ", + ((uint16_t*)ahc->seep_config)[i]); + } + seq_putc(m, '\n'); + } + seq_putc(m, '\n'); + + max_targ = 16; + if ((ahc->features & (AHC_WIDE|AHC_TWIN)) == 0) + max_targ = 8; + + for (i = 0; i < max_targ; i++) { + u_int our_id; + u_int target_id; + char channel; + + channel = 'A'; + our_id = ahc->our_id; + target_id = i; + if (i > 7 && (ahc->features & AHC_TWIN) != 0) { + channel = 'B'; + our_id = ahc->our_id_b; + target_id = i % 8; + } + + ahc_dump_target_state(ahc, m, our_id, + channel, target_id, i); + } + return 0; +} diff --git a/drivers/scsi/aic7xxx/aic7xxx_reg.h_shipped b/drivers/scsi/aic7xxx/aic7xxx_reg.h_shipped new file mode 100644 index 000000000..473039df0 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx_reg.h_shipped @@ -0,0 +1,912 @@ +/* + * DO NOT EDIT - This file is automatically generated + * from the following source files: + * + * $Id: //depot/aic7xxx/aic7xxx/aic7xxx.seq#58 $ + * $Id: //depot/aic7xxx/aic7xxx/aic7xxx.reg#40 $ + */ +typedef int (ahc_reg_print_t)(u_int, u_int *, u_int); +typedef struct ahc_reg_parse_entry { + char *name; + uint8_t value; + uint8_t mask; +} ahc_reg_parse_entry_t; + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_scsiseq_print; +#else +#define ahc_scsiseq_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SCSISEQ", 0x00, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_sxfrctl0_print; +#else +#define ahc_sxfrctl0_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SXFRCTL0", 0x01, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_scsisigi_print; +#else +#define ahc_scsisigi_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SCSISIGI", 0x03, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_scsirate_print; +#else +#define ahc_scsirate_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SCSIRATE", 0x04, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_sstat0_print; +#else +#define ahc_sstat0_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SSTAT0", 0x0b, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_sstat1_print; +#else +#define ahc_sstat1_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SSTAT1", 0x0c, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_sstat2_print; +#else +#define ahc_sstat2_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SSTAT2", 0x0d, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_sstat3_print; +#else +#define ahc_sstat3_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SSTAT3", 0x0e, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_simode0_print; +#else +#define ahc_simode0_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SIMODE0", 0x10, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_simode1_print; +#else +#define ahc_simode1_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SIMODE1", 0x11, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_scsibusl_print; +#else +#define ahc_scsibusl_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SCSIBUSL", 0x12, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_sblkctl_print; +#else +#define ahc_sblkctl_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SBLKCTL", 0x1f, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_seq_flags_print; +#else +#define ahc_seq_flags_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SEQ_FLAGS", 0x3c, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_lastphase_print; +#else +#define ahc_lastphase_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "LASTPHASE", 0x3f, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_seqctl_print; +#else +#define ahc_seqctl_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SEQCTL", 0x60, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_sram_base_print; +#else +#define ahc_sram_base_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SRAM_BASE", 0x70, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_error_print; +#else +#define ahc_error_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "ERROR", 0x92, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_dfcntrl_print; +#else +#define ahc_dfcntrl_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "DFCNTRL", 0x93, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_dfstatus_print; +#else +#define ahc_dfstatus_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "DFSTATUS", 0x94, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_scsiphase_print; +#else +#define ahc_scsiphase_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SCSIPHASE", 0x9e, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_scb_base_print; +#else +#define ahc_scb_base_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SCB_BASE", 0xa0, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_scb_control_print; +#else +#define ahc_scb_control_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SCB_CONTROL", 0xb8, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_scb_scsiid_print; +#else +#define ahc_scb_scsiid_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SCB_SCSIID", 0xb9, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_scb_lun_print; +#else +#define ahc_scb_lun_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SCB_LUN", 0xba, regvalue, cur_col, wrap) +#endif + +#if AIC_DEBUG_REGISTERS +ahc_reg_print_t ahc_scb_tag_print; +#else +#define ahc_scb_tag_print(regvalue, cur_col, wrap) \ + ahc_print_register(NULL, 0, "SCB_TAG", 0xbb, regvalue, cur_col, wrap) +#endif + + +#define SCSISEQ 0x00 +#define TEMODE 0x80 +#define SCSIRSTO 0x01 + +#define SXFRCTL0 0x01 +#define DFON 0x80 +#define DFPEXP 0x40 +#define FAST20 0x20 +#define CLRSTCNT 0x10 +#define SPIOEN 0x08 +#define SCAMEN 0x04 +#define CLRCHN 0x02 + +#define SXFRCTL1 0x02 +#define STIMESEL 0x18 +#define BITBUCKET 0x80 +#define SWRAPEN 0x40 +#define ENSTIMER 0x04 +#define ACTNEGEN 0x02 +#define STPWEN 0x01 + +#define SCSISIGO 0x03 +#define CDO 0x80 +#define IOO 0x40 +#define MSGO 0x20 +#define ATNO 0x10 +#define SELO 0x08 +#define BSYO 0x04 +#define REQO 0x02 +#define ACKO 0x01 + +#define SCSISIGI 0x03 +#define P_DATAIN_DT 0x60 +#define P_DATAOUT_DT 0x20 +#define ATNI 0x10 +#define SELI 0x08 +#define BSYI 0x04 +#define REQI 0x02 +#define ACKI 0x01 + +#define SCSIRATE 0x04 +#define SXFR 0x70 +#define SOFS 0x0f +#define SXFR_ULTRA2 0x0f +#define WIDEXFER 0x80 +#define ENABLE_CRC 0x40 +#define SINGLE_EDGE 0x10 + +#define SCSIID 0x05 +#define SCSIOFFSET 0x05 +#define SOFS_ULTRA2 0x7f + +#define SCSIDATL 0x06 + +#define SCSIDATH 0x07 + +#define OPTIONMODE 0x08 +#define OPTIONMODE_DEFAULTS 0x03 +#define AUTORATEEN 0x80 +#define AUTOACKEN 0x40 +#define ATNMGMNTEN 0x20 +#define BUSFREEREV 0x10 +#define EXPPHASEDIS 0x08 +#define SCSIDATL_IMGEN 0x04 +#define AUTO_MSGOUT_DE 0x02 +#define DIS_MSGIN_DUALEDGE 0x01 + +#define STCNT 0x08 + +#define TARGCRCCNT 0x0a + +#define CLRSINT0 0x0b +#define CLRSELDO 0x40 +#define CLRSELDI 0x20 +#define CLRSELINGO 0x10 +#define CLRIOERR 0x08 +#define CLRSWRAP 0x08 +#define CLRSPIORDY 0x02 + +#define SSTAT0 0x0b +#define TARGET 0x80 +#define SELDO 0x40 +#define SELDI 0x20 +#define SELINGO 0x10 +#define SWRAP 0x08 +#define IOERR 0x08 +#define SDONE 0x04 +#define SPIORDY 0x02 +#define DMADONE 0x01 + +#define CLRSINT1 0x0c +#define CLRSELTIMEO 0x80 +#define CLRATNO 0x40 +#define CLRSCSIRSTI 0x20 +#define CLRBUSFREE 0x08 +#define CLRSCSIPERR 0x04 +#define CLRPHASECHG 0x02 +#define CLRREQINIT 0x01 + +#define SSTAT1 0x0c +#define SELTO 0x80 +#define ATNTARG 0x40 +#define SCSIRSTI 0x20 +#define PHASEMIS 0x10 +#define BUSFREE 0x08 +#define SCSIPERR 0x04 +#define PHASECHG 0x02 +#define REQINIT 0x01 + +#define SSTAT2 0x0d +#define SFCNT 0x1f +#define OVERRUN 0x80 +#define SHVALID 0x40 +#define EXP_ACTIVE 0x10 +#define CRCVALERR 0x08 +#define CRCENDERR 0x04 +#define CRCREQERR 0x02 +#define DUAL_EDGE_ERR 0x01 + +#define SSTAT3 0x0e +#define SCSICNT 0xf0 +#define U2OFFCNT 0x7f +#define OFFCNT 0x0f + +#define SCSIID_ULTRA2 0x0f + +#define SIMODE0 0x10 +#define ENSELDO 0x40 +#define ENSELDI 0x20 +#define ENSELINGO 0x10 +#define ENIOERR 0x08 +#define ENSWRAP 0x08 +#define ENSDONE 0x04 +#define ENSPIORDY 0x02 +#define ENDMADONE 0x01 + +#define SIMODE1 0x11 +#define ENSELTIMO 0x80 +#define ENATNTARG 0x40 +#define ENSCSIRST 0x20 +#define ENPHASEMIS 0x10 +#define ENBUSFREE 0x08 +#define ENSCSIPERR 0x04 +#define ENPHASECHG 0x02 +#define ENREQINIT 0x01 + +#define SCSIBUSL 0x12 + +#define SCSIBUSH 0x13 + +#define SXFRCTL2 0x13 +#define ASYNC_SETUP 0x07 +#define AUTORSTDIS 0x10 +#define CMDDMAEN 0x08 + +#define SHADDR 0x14 + +#define SELTIMER 0x18 +#define TARGIDIN 0x18 +#define STAGE6 0x20 +#define STAGE5 0x10 +#define STAGE4 0x08 +#define STAGE3 0x04 +#define STAGE2 0x02 +#define STAGE1 0x01 + +#define SELID 0x19 +#define SELID_MASK 0xf0 +#define ONEBIT 0x08 + +#define SCAMCTL 0x1a +#define SCAMLVL 0x03 +#define ENSCAMSELO 0x80 +#define CLRSCAMSELID 0x40 +#define ALTSTIM 0x20 +#define DFLTTID 0x10 + +#define SPIOCAP 0x1b +#define SOFT1 0x80 +#define SOFT0 0x40 +#define SOFTCMDEN 0x20 +#define EXT_BRDCTL 0x10 +#define SEEPROM 0x08 +#define EEPROM 0x04 +#define ROM 0x02 +#define SSPIOCPS 0x01 + +#define TARGID 0x1b + +#define BRDCTL 0x1d +#define BRDDAT7 0x80 +#define BRDDAT6 0x40 +#define BRDDAT5 0x20 +#define BRDSTB 0x10 +#define BRDDAT4 0x10 +#define BRDDAT3 0x08 +#define BRDCS 0x08 +#define BRDDAT2 0x04 +#define BRDRW 0x04 +#define BRDRW_ULTRA2 0x02 +#define BRDCTL1 0x02 +#define BRDCTL0 0x01 +#define BRDSTB_ULTRA2 0x01 + +#define SEECTL 0x1e +#define EXTARBACK 0x80 +#define EXTARBREQ 0x40 +#define SEEMS 0x20 +#define SEERDY 0x10 +#define SEECS 0x08 +#define SEECK 0x04 +#define SEEDO 0x02 +#define SEEDI 0x01 + +#define SBLKCTL 0x1f +#define DIAGLEDEN 0x80 +#define DIAGLEDON 0x40 +#define AUTOFLUSHDIS 0x20 +#define SELBUSB 0x08 +#define ENAB40 0x08 +#define ENAB20 0x04 +#define SELWIDE 0x02 +#define XCVR 0x01 + +#define BUSY_TARGETS 0x20 +#define TARG_SCSIRATE 0x20 + +#define ULTRA_ENB 0x30 +#define CMDSIZE_TABLE 0x30 + +#define DISC_DSB 0x32 + +#define CMDSIZE_TABLE_TAIL 0x34 + +#define MWI_RESIDUAL 0x38 + +#define NEXT_QUEUED_SCB 0x39 + +#define MSG_OUT 0x3a + +#define DMAPARAMS 0x3b +#define PRELOADEN 0x80 +#define WIDEODD 0x40 +#define SCSIEN 0x20 +#define SDMAEN 0x10 +#define SDMAENACK 0x10 +#define HDMAEN 0x08 +#define HDMAENACK 0x08 +#define DIRECTION 0x04 +#define FIFOFLUSH 0x02 +#define FIFORESET 0x01 + +#define SEQ_FLAGS 0x3c +#define NOT_IDENTIFIED 0x80 +#define NO_CDB_SENT 0x40 +#define TARGET_CMD_IS_TAGGED 0x40 +#define DPHASE 0x20 +#define TARG_CMD_PENDING 0x10 +#define CMDPHASE_PENDING 0x08 +#define DPHASE_PENDING 0x04 +#define SPHASE_PENDING 0x02 +#define NO_DISCONNECT 0x01 + +#define SAVED_SCSIID 0x3d + +#define SAVED_LUN 0x3e + +#define LASTPHASE 0x3f +#define P_MESGIN 0xe0 +#define PHASE_MASK 0xe0 +#define P_STATUS 0xc0 +#define P_MESGOUT 0xa0 +#define P_COMMAND 0x80 +#define P_DATAIN 0x40 +#define P_BUSFREE 0x01 +#define P_DATAOUT 0x00 +#define CDI 0x80 +#define IOI 0x40 +#define MSGI 0x20 + +#define WAITING_SCBH 0x40 + +#define DISCONNECTED_SCBH 0x41 + +#define FREE_SCBH 0x42 + +#define COMPLETE_SCBH 0x43 + +#define HSCB_ADDR 0x44 + +#define SHARED_DATA_ADDR 0x48 + +#define KERNEL_QINPOS 0x4c + +#define QINPOS 0x4d + +#define QOUTPOS 0x4e + +#define KERNEL_TQINPOS 0x4f + +#define TQINPOS 0x50 + +#define ARG_1 0x51 +#define RETURN_1 0x51 +#define SEND_MSG 0x80 +#define SEND_SENSE 0x40 +#define SEND_REJ 0x20 +#define MSGOUT_PHASEMIS 0x10 +#define EXIT_MSG_LOOP 0x08 +#define CONT_MSG_LOOP 0x04 +#define CONT_TARG_SESSION 0x02 + +#define ARG_2 0x52 +#define RETURN_2 0x52 + +#define LAST_MSG 0x53 +#define TARG_IMMEDIATE_SCB 0x53 + +#define SCSISEQ_TEMPLATE 0x54 +#define ENSELO 0x40 +#define ENSELI 0x20 +#define ENRSELI 0x10 +#define ENAUTOATNO 0x08 +#define ENAUTOATNI 0x04 +#define ENAUTOATNP 0x02 + +#define HA_274_BIOSGLOBAL 0x56 +#define INITIATOR_TAG 0x56 +#define HA_274_EXTENDED_TRANS 0x01 + +#define SEQ_FLAGS2 0x57 +#define TARGET_MSG_PENDING 0x02 +#define SCB_DMA 0x01 + +#define SCSICONF 0x5a +#define HWSCSIID 0x0f +#define HSCSIID 0x07 +#define TERM_ENB 0x80 +#define RESET_SCSI 0x40 +#define ENSPCHK 0x20 + +#define INTDEF 0x5c +#define VECTOR 0x0f +#define EDGE_TRIG 0x80 + +#define HOSTCONF 0x5d + +#define HA_274_BIOSCTRL 0x5f +#define BIOSDISABLED 0x30 +#define BIOSMODE 0x30 +#define CHANNEL_B_PRIMARY 0x08 + +#define SEQCTL 0x60 +#define PERRORDIS 0x80 +#define PAUSEDIS 0x40 +#define FAILDIS 0x20 +#define FASTMODE 0x10 +#define BRKADRINTEN 0x08 +#define STEP 0x04 +#define SEQRESET 0x02 +#define LOADRAM 0x01 + +#define SEQRAM 0x61 + +#define SEQADDR0 0x62 + +#define SEQADDR1 0x63 +#define SEQADDR1_MASK 0x01 + +#define ACCUM 0x64 + +#define SINDEX 0x65 + +#define DINDEX 0x66 + +#define ALLONES 0x69 + +#define ALLZEROS 0x6a + +#define NONE 0x6a + +#define FLAGS 0x6b +#define ZERO 0x02 +#define CARRY 0x01 + +#define SINDIR 0x6c + +#define DINDIR 0x6d + +#define FUNCTION1 0x6e + +#define STACK 0x6f + +#define TARG_OFFSET 0x70 + +#define SRAM_BASE 0x70 + +#define BCTL 0x84 +#define ACE 0x08 +#define ENABLE 0x01 + +#define DSCOMMAND0 0x84 +#define CACHETHEN 0x80 +#define DPARCKEN 0x40 +#define MPARCKEN 0x20 +#define EXTREQLCK 0x10 +#define INTSCBRAMSEL 0x08 +#define RAMPS 0x04 +#define USCBSIZE32 0x02 +#define CIOPARCKEN 0x01 + +#define BUSTIME 0x85 +#define BOFF 0xf0 +#define BON 0x0f + +#define DSCOMMAND1 0x85 +#define DSLATT 0xfc +#define HADDLDSEL1 0x02 +#define HADDLDSEL0 0x01 + +#define BUSSPD 0x86 +#define DFTHRSH 0xc0 +#define DFTHRSH_75 0x80 +#define STBOFF 0x38 +#define STBON 0x07 + +#define HS_MAILBOX 0x86 +#define HOST_MAILBOX 0xf0 +#define HOST_TQINPOS 0x80 +#define SEQ_MAILBOX 0x0f + +#define DSPCISTATUS 0x86 +#define DFTHRSH_100 0xc0 + +#define HCNTRL 0x87 +#define POWRDN 0x40 +#define SWINT 0x10 +#define IRQMS 0x08 +#define PAUSE 0x04 +#define INTEN 0x02 +#define CHIPRST 0x01 +#define CHIPRSTACK 0x01 + +#define HADDR 0x88 + +#define HCNT 0x8c + +#define SCBPTR 0x90 + +#define INTSTAT 0x91 +#define SEQINT_MASK 0xf1 +#define OUT_OF_RANGE 0xe1 +#define NO_FREE_SCB 0xd1 +#define SCB_MISMATCH 0xc1 +#define MISSED_BUSFREE 0xb1 +#define MKMSG_FAILED 0xa1 +#define DATA_OVERRUN 0x91 +#define PERR_DETECTED 0x81 +#define BAD_STATUS 0x71 +#define HOST_MSG_LOOP 0x61 +#define PDATA_REINIT 0x51 +#define IGN_WIDE_RES 0x41 +#define NO_MATCH 0x31 +#define PROTO_VIOLATION 0x21 +#define SEND_REJECT 0x11 +#define INT_PEND 0x0f +#define BAD_PHASE 0x01 +#define BRKADRINT 0x08 +#define SCSIINT 0x04 +#define CMDCMPLT 0x02 +#define SEQINT 0x01 + +#define CLRINT 0x92 +#define CLRPARERR 0x10 +#define CLRBRKADRINT 0x08 +#define CLRSCSIINT 0x04 +#define CLRCMDINT 0x02 +#define CLRSEQINT 0x01 + +#define ERROR 0x92 +#define CIOPARERR 0x80 +#define PCIERRSTAT 0x40 +#define MPARERR 0x20 +#define DPARERR 0x10 +#define SQPARERR 0x08 +#define ILLOPCODE 0x04 +#define ILLSADDR 0x02 +#define ILLHADDR 0x01 + +#define DFCNTRL 0x93 + +#define DFSTATUS 0x94 +#define PRELOAD_AVAIL 0x80 +#define DFCACHETH 0x40 +#define FIFOQWDEMP 0x20 +#define MREQPEND 0x10 +#define HDONE 0x08 +#define DFTHRESH 0x04 +#define FIFOFULL 0x02 +#define FIFOEMP 0x01 + +#define DFWADDR 0x95 + +#define DFRADDR 0x97 + +#define DFDAT 0x99 + +#define SCBCNT 0x9a +#define SCBCNT_MASK 0x1f +#define SCBAUTO 0x80 + +#define QINFIFO 0x9b + +#define QINCNT 0x9c + +#define QOUTFIFO 0x9d + +#define CRCCONTROL1 0x9d +#define CRCONSEEN 0x80 +#define CRCVALCHKEN 0x40 +#define CRCENDCHKEN 0x20 +#define CRCREQCHKEN 0x10 +#define TARGCRCENDEN 0x08 +#define TARGCRCCNTEN 0x04 + +#define QOUTCNT 0x9e + +#define SCSIPHASE 0x9e +#define DATA_PHASE_MASK 0x03 +#define STATUS_PHASE 0x20 +#define COMMAND_PHASE 0x10 +#define MSG_IN_PHASE 0x08 +#define MSG_OUT_PHASE 0x04 +#define DATA_IN_PHASE 0x02 +#define DATA_OUT_PHASE 0x01 + +#define SFUNCT 0x9f +#define ALT_MODE 0x80 + +#define SCB_BASE 0xa0 + +#define SCB_CDB_PTR 0xa0 +#define SCB_CDB_STORE 0xa0 +#define SCB_RESIDUAL_DATACNT 0xa0 + +#define SCB_RESIDUAL_SGPTR 0xa4 + +#define SCB_SCSI_STATUS 0xa8 + +#define SCB_TARGET_PHASES 0xa9 + +#define SCB_TARGET_DATA_DIR 0xaa + +#define SCB_TARGET_ITAG 0xab + +#define SCB_DATAPTR 0xac + +#define SCB_DATACNT 0xb0 +#define SG_HIGH_ADDR_BITS 0x7f +#define SG_LAST_SEG 0x80 + +#define SCB_SGPTR 0xb4 +#define SG_RESID_VALID 0x04 +#define SG_FULL_RESID 0x02 +#define SG_LIST_NULL 0x01 + +#define SCB_CONTROL 0xb8 +#define SCB_TAG_TYPE 0x03 +#define TARGET_SCB 0x80 +#define STATUS_RCVD 0x80 +#define DISCENB 0x40 +#define TAG_ENB 0x20 +#define MK_MESSAGE 0x10 +#define ULTRAENB 0x08 +#define DISCONNECTED 0x04 + +#define SCB_SCSIID 0xb9 +#define TID 0xf0 +#define TWIN_TID 0x70 +#define OID 0x0f +#define TWIN_CHNLB 0x80 + +#define SCB_LUN 0xba +#define LID 0x3f +#define SCB_XFERLEN_ODD 0x80 + +#define SCB_TAG 0xbb + +#define SCB_CDB_LEN 0xbc + +#define SCB_SCSIRATE 0xbd + +#define SCB_SCSIOFFSET 0xbe + +#define SCB_NEXT 0xbf + +#define SCB_64_SPARE 0xc0 + +#define SEECTL_2840 0xc0 +#define CS_2840 0x04 +#define CK_2840 0x02 +#define DO_2840 0x01 + +#define STATUS_2840 0xc1 +#define BIOS_SEL 0x60 +#define ADSEL 0x1e +#define EEPROM_TF 0x80 +#define DI_2840 0x01 + +#define SCB_64_BTT 0xd0 + +#define CCHADDR 0xe0 + +#define CCHCNT 0xe8 + +#define CCSGRAM 0xe9 + +#define CCSGADDR 0xea + +#define CCSGCTL 0xeb +#define CCSGDONE 0x80 +#define CCSGEN 0x08 +#define SG_FETCH_NEEDED 0x02 +#define CCSGRESET 0x01 + +#define CCSCBRAM 0xec + +#define CCSCBADDR 0xed + +#define CCSCBCTL 0xee +#define CCSCBDONE 0x80 +#define ARRDONE 0x40 +#define CCARREN 0x10 +#define CCSCBEN 0x08 +#define CCSCBDIR 0x04 +#define CCSCBRESET 0x01 + +#define CCSCBCNT 0xef + +#define SCBBADDR 0xf0 + +#define CCSCBPTR 0xf1 + +#define HNSCB_QOFF 0xf4 + +#define SNSCB_QOFF 0xf6 + +#define SDSCB_QOFF 0xf8 + +#define QOFF_CTLSTA 0xfa +#define SCB_QSIZE 0x07 +#define SCB_QSIZE_256 0x06 +#define SCB_AVAIL 0x40 +#define SNSCB_ROLLOVER 0x20 +#define SDSCB_ROLLOVER 0x10 + +#define DFF_THRSH 0xfb +#define WR_DFTHRSH 0x70 +#define WR_DFTHRSH_MAX 0x70 +#define WR_DFTHRSH_90 0x60 +#define WR_DFTHRSH_85 0x50 +#define WR_DFTHRSH_75 0x40 +#define WR_DFTHRSH_63 0x30 +#define WR_DFTHRSH_50 0x20 +#define WR_DFTHRSH_25 0x10 +#define RD_DFTHRSH 0x07 +#define RD_DFTHRSH_MAX 0x07 +#define RD_DFTHRSH_90 0x06 +#define RD_DFTHRSH_85 0x05 +#define RD_DFTHRSH_75 0x04 +#define RD_DFTHRSH_63 0x03 +#define RD_DFTHRSH_50 0x02 +#define RD_DFTHRSH_25 0x01 +#define RD_DFTHRSH_MIN 0x00 +#define WR_DFTHRSH_MIN 0x00 + +#define SG_CACHE_SHADOW 0xfc +#define SG_ADDR_MASK 0xf8 +#define LAST_SEG 0x02 +#define LAST_SEG_DONE 0x01 + +#define SG_CACHE_PRE 0xfc + + +#define TARGET_CMD_CMPLT 0xfe +#define MAX_OFFSET_ULTRA2 0x7f +#define MAX_OFFSET_16BIT 0x08 +#define BUS_8_BIT 0x00 +#define TID_SHIFT 0x04 +#define STATUS_QUEUE_FULL 0x28 +#define STATUS_BUSY 0x08 +#define SCB_DOWNLOAD_SIZE_64 0x30 +#define MAX_OFFSET_8BIT 0x0f +#define HOST_MAILBOX_SHIFT 0x04 +#define CCSGADDR_MAX 0x80 +#define BUS_32_BIT 0x02 +#define SG_SIZEOF 0x08 +#define SEQ_MAILBOX_SHIFT 0x00 +#define SCB_LIST_NULL 0xff +#define SCB_DOWNLOAD_SIZE 0x20 +#define CMD_GROUP_CODE_SHIFT 0x05 +#define CCSGRAM_MAXSEGS 0x10 +#define TARGET_DATA_IN 0x01 +#define STACK_SIZE 0x04 +#define SCB_UPLOAD_SIZE 0x20 +#define MAX_OFFSET 0x7f +#define HOST_MSG 0xff +#define BUS_16_BIT 0x01 + + +/* Downloaded Constant Definitions */ +#define INVERTED_CACHESIZE_MASK 0x03 +#define SG_PREFETCH_ALIGN_MASK 0x05 +#define SG_PREFETCH_ADDR_MASK 0x06 +#define QOUTFIFO_OFFSET 0x00 +#define SG_PREFETCH_CNT 0x04 +#define QINFIFO_OFFSET 0x01 +#define CACHESIZE_MASK 0x02 +#define DOWNLOAD_CONST_COUNT 0x07 + + +/* Exported Labels */ diff --git a/drivers/scsi/aic7xxx/aic7xxx_reg_print.c_shipped b/drivers/scsi/aic7xxx/aic7xxx_reg_print.c_shipped new file mode 100644 index 000000000..9f9b88047 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx_reg_print.c_shipped @@ -0,0 +1,413 @@ +/* + * DO NOT EDIT - This file is automatically generated + * from the following source files: + * + * $Id: //depot/aic7xxx/aic7xxx/aic7xxx.seq#58 $ + * $Id: //depot/aic7xxx/aic7xxx/aic7xxx.reg#40 $ + */ + +#include "aic7xxx_osm.h" + +static const ahc_reg_parse_entry_t SCSISEQ_parse_table[] = { + { "SCSIRSTO", 0x01, 0x01 }, + { "ENAUTOATNP", 0x02, 0x02 }, + { "ENAUTOATNI", 0x04, 0x04 }, + { "ENAUTOATNO", 0x08, 0x08 }, + { "ENRSELI", 0x10, 0x10 }, + { "ENSELI", 0x20, 0x20 }, + { "ENSELO", 0x40, 0x40 }, + { "TEMODE", 0x80, 0x80 } +}; + +int +ahc_scsiseq_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SCSISEQ_parse_table, 8, "SCSISEQ", + 0x00, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SXFRCTL0_parse_table[] = { + { "CLRCHN", 0x02, 0x02 }, + { "SCAMEN", 0x04, 0x04 }, + { "SPIOEN", 0x08, 0x08 }, + { "CLRSTCNT", 0x10, 0x10 }, + { "FAST20", 0x20, 0x20 }, + { "DFPEXP", 0x40, 0x40 }, + { "DFON", 0x80, 0x80 } +}; + +int +ahc_sxfrctl0_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SXFRCTL0_parse_table, 7, "SXFRCTL0", + 0x01, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SCSISIGI_parse_table[] = { + { "ACKI", 0x01, 0x01 }, + { "REQI", 0x02, 0x02 }, + { "BSYI", 0x04, 0x04 }, + { "SELI", 0x08, 0x08 }, + { "ATNI", 0x10, 0x10 }, + { "MSGI", 0x20, 0x20 }, + { "IOI", 0x40, 0x40 }, + { "CDI", 0x80, 0x80 }, + { "P_DATAOUT", 0x00, 0x00 }, + { "P_DATAOUT_DT", 0x20, 0x20 }, + { "P_DATAIN", 0x40, 0x40 }, + { "P_DATAIN_DT", 0x60, 0x60 }, + { "P_COMMAND", 0x80, 0x80 }, + { "P_MESGOUT", 0xa0, 0xa0 }, + { "P_STATUS", 0xc0, 0xc0 }, + { "PHASE_MASK", 0xe0, 0xe0 }, + { "P_MESGIN", 0xe0, 0xe0 } +}; + +int +ahc_scsisigi_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SCSISIGI_parse_table, 17, "SCSISIGI", + 0x03, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SCSIRATE_parse_table[] = { + { "SINGLE_EDGE", 0x10, 0x10 }, + { "ENABLE_CRC", 0x40, 0x40 }, + { "WIDEXFER", 0x80, 0x80 }, + { "SXFR_ULTRA2", 0x0f, 0x0f }, + { "SOFS", 0x0f, 0x0f }, + { "SXFR", 0x70, 0x70 } +}; + +int +ahc_scsirate_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SCSIRATE_parse_table, 6, "SCSIRATE", + 0x04, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SSTAT0_parse_table[] = { + { "DMADONE", 0x01, 0x01 }, + { "SPIORDY", 0x02, 0x02 }, + { "SDONE", 0x04, 0x04 }, + { "SWRAP", 0x08, 0x08 }, + { "IOERR", 0x08, 0x08 }, + { "SELINGO", 0x10, 0x10 }, + { "SELDI", 0x20, 0x20 }, + { "SELDO", 0x40, 0x40 }, + { "TARGET", 0x80, 0x80 } +}; + +int +ahc_sstat0_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SSTAT0_parse_table, 9, "SSTAT0", + 0x0b, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SSTAT1_parse_table[] = { + { "REQINIT", 0x01, 0x01 }, + { "PHASECHG", 0x02, 0x02 }, + { "SCSIPERR", 0x04, 0x04 }, + { "BUSFREE", 0x08, 0x08 }, + { "PHASEMIS", 0x10, 0x10 }, + { "SCSIRSTI", 0x20, 0x20 }, + { "ATNTARG", 0x40, 0x40 }, + { "SELTO", 0x80, 0x80 } +}; + +int +ahc_sstat1_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SSTAT1_parse_table, 8, "SSTAT1", + 0x0c, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SSTAT2_parse_table[] = { + { "DUAL_EDGE_ERR", 0x01, 0x01 }, + { "CRCREQERR", 0x02, 0x02 }, + { "CRCENDERR", 0x04, 0x04 }, + { "CRCVALERR", 0x08, 0x08 }, + { "EXP_ACTIVE", 0x10, 0x10 }, + { "SHVALID", 0x40, 0x40 }, + { "OVERRUN", 0x80, 0x80 }, + { "SFCNT", 0x1f, 0x1f } +}; + +int +ahc_sstat2_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SSTAT2_parse_table, 8, "SSTAT2", + 0x0d, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SSTAT3_parse_table[] = { + { "OFFCNT", 0x0f, 0x0f }, + { "U2OFFCNT", 0x7f, 0x7f }, + { "SCSICNT", 0xf0, 0xf0 } +}; + +int +ahc_sstat3_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SSTAT3_parse_table, 3, "SSTAT3", + 0x0e, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SIMODE0_parse_table[] = { + { "ENDMADONE", 0x01, 0x01 }, + { "ENSPIORDY", 0x02, 0x02 }, + { "ENSDONE", 0x04, 0x04 }, + { "ENSWRAP", 0x08, 0x08 }, + { "ENIOERR", 0x08, 0x08 }, + { "ENSELINGO", 0x10, 0x10 }, + { "ENSELDI", 0x20, 0x20 }, + { "ENSELDO", 0x40, 0x40 } +}; + +int +ahc_simode0_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SIMODE0_parse_table, 8, "SIMODE0", + 0x10, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SIMODE1_parse_table[] = { + { "ENREQINIT", 0x01, 0x01 }, + { "ENPHASECHG", 0x02, 0x02 }, + { "ENSCSIPERR", 0x04, 0x04 }, + { "ENBUSFREE", 0x08, 0x08 }, + { "ENPHASEMIS", 0x10, 0x10 }, + { "ENSCSIRST", 0x20, 0x20 }, + { "ENATNTARG", 0x40, 0x40 }, + { "ENSELTIMO", 0x80, 0x80 } +}; + +int +ahc_simode1_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SIMODE1_parse_table, 8, "SIMODE1", + 0x11, regvalue, cur_col, wrap)); +} + +int +ahc_scsibusl_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(NULL, 0, "SCSIBUSL", + 0x12, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SBLKCTL_parse_table[] = { + { "XCVR", 0x01, 0x01 }, + { "SELWIDE", 0x02, 0x02 }, + { "ENAB20", 0x04, 0x04 }, + { "SELBUSB", 0x08, 0x08 }, + { "ENAB40", 0x08, 0x08 }, + { "AUTOFLUSHDIS", 0x20, 0x20 }, + { "DIAGLEDON", 0x40, 0x40 }, + { "DIAGLEDEN", 0x80, 0x80 } +}; + +int +ahc_sblkctl_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SBLKCTL_parse_table, 8, "SBLKCTL", + 0x1f, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SEQ_FLAGS_parse_table[] = { + { "NO_DISCONNECT", 0x01, 0x01 }, + { "SPHASE_PENDING", 0x02, 0x02 }, + { "DPHASE_PENDING", 0x04, 0x04 }, + { "CMDPHASE_PENDING", 0x08, 0x08 }, + { "TARG_CMD_PENDING", 0x10, 0x10 }, + { "DPHASE", 0x20, 0x20 }, + { "NO_CDB_SENT", 0x40, 0x40 }, + { "TARGET_CMD_IS_TAGGED",0x40, 0x40 }, + { "NOT_IDENTIFIED", 0x80, 0x80 } +}; + +int +ahc_seq_flags_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SEQ_FLAGS_parse_table, 9, "SEQ_FLAGS", + 0x3c, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t LASTPHASE_parse_table[] = { + { "MSGI", 0x20, 0x20 }, + { "IOI", 0x40, 0x40 }, + { "CDI", 0x80, 0x80 }, + { "P_DATAOUT", 0x00, 0x00 }, + { "P_BUSFREE", 0x01, 0x01 }, + { "P_DATAIN", 0x40, 0x40 }, + { "P_COMMAND", 0x80, 0x80 }, + { "P_MESGOUT", 0xa0, 0xa0 }, + { "P_STATUS", 0xc0, 0xc0 }, + { "PHASE_MASK", 0xe0, 0xe0 }, + { "P_MESGIN", 0xe0, 0xe0 } +}; + +int +ahc_lastphase_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(LASTPHASE_parse_table, 11, "LASTPHASE", + 0x3f, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SEQCTL_parse_table[] = { + { "LOADRAM", 0x01, 0x01 }, + { "SEQRESET", 0x02, 0x02 }, + { "STEP", 0x04, 0x04 }, + { "BRKADRINTEN", 0x08, 0x08 }, + { "FASTMODE", 0x10, 0x10 }, + { "FAILDIS", 0x20, 0x20 }, + { "PAUSEDIS", 0x40, 0x40 }, + { "PERRORDIS", 0x80, 0x80 } +}; + +int +ahc_seqctl_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SEQCTL_parse_table, 8, "SEQCTL", + 0x60, regvalue, cur_col, wrap)); +} + +int +ahc_sram_base_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(NULL, 0, "SRAM_BASE", + 0x70, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t ERROR_parse_table[] = { + { "ILLHADDR", 0x01, 0x01 }, + { "ILLSADDR", 0x02, 0x02 }, + { "ILLOPCODE", 0x04, 0x04 }, + { "SQPARERR", 0x08, 0x08 }, + { "DPARERR", 0x10, 0x10 }, + { "MPARERR", 0x20, 0x20 }, + { "PCIERRSTAT", 0x40, 0x40 }, + { "CIOPARERR", 0x80, 0x80 } +}; + +int +ahc_error_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(ERROR_parse_table, 8, "ERROR", + 0x92, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t DFCNTRL_parse_table[] = { + { "FIFORESET", 0x01, 0x01 }, + { "FIFOFLUSH", 0x02, 0x02 }, + { "DIRECTION", 0x04, 0x04 }, + { "HDMAEN", 0x08, 0x08 }, + { "HDMAENACK", 0x08, 0x08 }, + { "SDMAEN", 0x10, 0x10 }, + { "SDMAENACK", 0x10, 0x10 }, + { "SCSIEN", 0x20, 0x20 }, + { "WIDEODD", 0x40, 0x40 }, + { "PRELOADEN", 0x80, 0x80 } +}; + +int +ahc_dfcntrl_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(DFCNTRL_parse_table, 10, "DFCNTRL", + 0x93, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t DFSTATUS_parse_table[] = { + { "FIFOEMP", 0x01, 0x01 }, + { "FIFOFULL", 0x02, 0x02 }, + { "DFTHRESH", 0x04, 0x04 }, + { "HDONE", 0x08, 0x08 }, + { "MREQPEND", 0x10, 0x10 }, + { "FIFOQWDEMP", 0x20, 0x20 }, + { "DFCACHETH", 0x40, 0x40 }, + { "PRELOAD_AVAIL", 0x80, 0x80 } +}; + +int +ahc_dfstatus_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(DFSTATUS_parse_table, 8, "DFSTATUS", + 0x94, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SCSIPHASE_parse_table[] = { + { "DATA_OUT_PHASE", 0x01, 0x01 }, + { "DATA_IN_PHASE", 0x02, 0x02 }, + { "MSG_OUT_PHASE", 0x04, 0x04 }, + { "MSG_IN_PHASE", 0x08, 0x08 }, + { "COMMAND_PHASE", 0x10, 0x10 }, + { "STATUS_PHASE", 0x20, 0x20 }, + { "DATA_PHASE_MASK", 0x03, 0x03 } +}; + +int +ahc_scsiphase_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SCSIPHASE_parse_table, 7, "SCSIPHASE", + 0x9e, regvalue, cur_col, wrap)); +} + +int +ahc_scb_base_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(NULL, 0, "SCB_BASE", + 0xa0, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SCB_CONTROL_parse_table[] = { + { "DISCONNECTED", 0x04, 0x04 }, + { "ULTRAENB", 0x08, 0x08 }, + { "MK_MESSAGE", 0x10, 0x10 }, + { "TAG_ENB", 0x20, 0x20 }, + { "DISCENB", 0x40, 0x40 }, + { "TARGET_SCB", 0x80, 0x80 }, + { "STATUS_RCVD", 0x80, 0x80 }, + { "SCB_TAG_TYPE", 0x03, 0x03 } +}; + +int +ahc_scb_control_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SCB_CONTROL_parse_table, 8, "SCB_CONTROL", + 0xb8, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SCB_SCSIID_parse_table[] = { + { "TWIN_CHNLB", 0x80, 0x80 }, + { "OID", 0x0f, 0x0f }, + { "TWIN_TID", 0x70, 0x70 }, + { "TID", 0xf0, 0xf0 } +}; + +int +ahc_scb_scsiid_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SCB_SCSIID_parse_table, 4, "SCB_SCSIID", + 0xb9, regvalue, cur_col, wrap)); +} + +static const ahc_reg_parse_entry_t SCB_LUN_parse_table[] = { + { "SCB_XFERLEN_ODD", 0x80, 0x80 }, + { "LID", 0x3f, 0x3f } +}; + +int +ahc_scb_lun_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(SCB_LUN_parse_table, 2, "SCB_LUN", + 0xba, regvalue, cur_col, wrap)); +} + +int +ahc_scb_tag_print(u_int regvalue, u_int *cur_col, u_int wrap) +{ + return (ahc_print_register(NULL, 0, "SCB_TAG", + 0xbb, regvalue, cur_col, wrap)); +} + diff --git a/drivers/scsi/aic7xxx/aic7xxx_seq.h_shipped b/drivers/scsi/aic7xxx/aic7xxx_seq.h_shipped new file mode 100644 index 000000000..f37362bc8 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic7xxx_seq.h_shipped @@ -0,0 +1,1307 @@ +/* + * DO NOT EDIT - This file is automatically generated + * from the following source files: + * + * $Id: //depot/aic7xxx/aic7xxx/aic7xxx.seq#58 $ + * $Id: //depot/aic7xxx/aic7xxx/aic7xxx.reg#40 $ + */ +static const uint8_t seqprog[] = { + 0xb2, 0x00, 0x00, 0x08, + 0xf7, 0x11, 0x22, 0x08, + 0x00, 0x65, 0xee, 0x59, + 0xf7, 0x01, 0x02, 0x08, + 0xff, 0x6a, 0x24, 0x08, + 0x40, 0x00, 0x40, 0x68, + 0x08, 0x1f, 0x3e, 0x10, + 0x40, 0x00, 0x40, 0x68, + 0xff, 0x40, 0x3c, 0x60, + 0x08, 0x1f, 0x3e, 0x10, + 0x60, 0x0b, 0x42, 0x68, + 0x40, 0xfa, 0x12, 0x78, + 0x01, 0x4d, 0xc8, 0x30, + 0x00, 0x4c, 0x12, 0x70, + 0x01, 0x39, 0xa2, 0x30, + 0x00, 0x6a, 0xc2, 0x5e, + 0x01, 0x51, 0x20, 0x31, + 0x01, 0x57, 0xae, 0x00, + 0x0d, 0x6a, 0x76, 0x00, + 0x00, 0x51, 0x14, 0x5e, + 0x01, 0x51, 0xc8, 0x30, + 0x00, 0x39, 0xc8, 0x60, + 0x00, 0xbb, 0x30, 0x70, + 0xc1, 0x6a, 0xda, 0x5e, + 0x01, 0xbf, 0x72, 0x30, + 0x01, 0x40, 0x7e, 0x31, + 0x01, 0x90, 0x80, 0x30, + 0x01, 0xf6, 0xd4, 0x30, + 0x01, 0x4d, 0x9a, 0x18, + 0xfe, 0x57, 0xae, 0x08, + 0x01, 0x40, 0x20, 0x31, + 0x00, 0x65, 0xcc, 0x58, + 0x60, 0x0b, 0x40, 0x78, + 0x08, 0x6a, 0x18, 0x00, + 0x08, 0x11, 0x22, 0x00, + 0x60, 0x0b, 0x00, 0x78, + 0x40, 0x0b, 0xfa, 0x68, + 0x80, 0x0b, 0xb6, 0x78, + 0x20, 0x6a, 0x16, 0x00, + 0xa4, 0x6a, 0x06, 0x00, + 0x08, 0x6a, 0x78, 0x00, + 0x01, 0x50, 0xc8, 0x30, + 0xe0, 0x6a, 0xcc, 0x00, + 0x48, 0x6a, 0xfe, 0x5d, + 0x01, 0x6a, 0xdc, 0x01, + 0x88, 0x6a, 0xcc, 0x00, + 0x48, 0x6a, 0xfe, 0x5d, + 0x01, 0x6a, 0x26, 0x01, + 0xf0, 0x19, 0x7a, 0x08, + 0x0f, 0x18, 0xc8, 0x08, + 0x0f, 0x0f, 0xc8, 0x08, + 0x0f, 0x05, 0xc8, 0x08, + 0x00, 0x3d, 0x7a, 0x00, + 0x08, 0x1f, 0x6e, 0x78, + 0x80, 0x3d, 0x7a, 0x00, + 0x01, 0x3d, 0xd8, 0x31, + 0x01, 0x3d, 0x32, 0x31, + 0x10, 0x03, 0x4e, 0x79, + 0x00, 0x65, 0xf2, 0x58, + 0x80, 0x66, 0xae, 0x78, + 0x01, 0x66, 0xd8, 0x31, + 0x01, 0x66, 0x32, 0x31, + 0x3f, 0x66, 0x7c, 0x08, + 0x40, 0x66, 0x82, 0x68, + 0x01, 0x3c, 0x78, 0x00, + 0x10, 0x03, 0x9e, 0x78, + 0x00, 0x65, 0xf2, 0x58, + 0xe0, 0x66, 0xc8, 0x18, + 0x00, 0x65, 0xaa, 0x50, + 0xdd, 0x66, 0xc8, 0x18, + 0x00, 0x65, 0xaa, 0x48, + 0x01, 0x66, 0xd8, 0x31, + 0x01, 0x66, 0x32, 0x31, + 0x10, 0x03, 0x4e, 0x79, + 0x00, 0x65, 0xf2, 0x58, + 0x01, 0x66, 0xd8, 0x31, + 0x01, 0x66, 0x32, 0x31, + 0x01, 0x66, 0xac, 0x30, + 0x40, 0x3c, 0x78, 0x00, + 0xff, 0x6a, 0xd8, 0x01, + 0xff, 0x6a, 0x32, 0x01, + 0x10, 0x3c, 0x78, 0x00, + 0x02, 0x57, 0x40, 0x69, + 0x10, 0x03, 0x3e, 0x69, + 0x00, 0x65, 0x20, 0x41, + 0x02, 0x57, 0xae, 0x00, + 0x00, 0x65, 0x9e, 0x40, + 0x61, 0x6a, 0xda, 0x5e, + 0x08, 0x51, 0x20, 0x71, + 0x02, 0x0b, 0xb2, 0x78, + 0x00, 0x65, 0xae, 0x40, + 0x1a, 0x01, 0x02, 0x00, + 0xf0, 0x19, 0x7a, 0x08, + 0x0f, 0x0f, 0xc8, 0x08, + 0x0f, 0x05, 0xc8, 0x08, + 0x00, 0x3d, 0x7a, 0x00, + 0x08, 0x1f, 0xc4, 0x78, + 0x80, 0x3d, 0x7a, 0x00, + 0x20, 0x6a, 0x16, 0x00, + 0x00, 0x65, 0xcc, 0x41, + 0x00, 0x65, 0xb4, 0x5e, + 0x00, 0x65, 0x12, 0x40, + 0x20, 0x11, 0xd2, 0x68, + 0x20, 0x6a, 0x18, 0x00, + 0x20, 0x11, 0x22, 0x00, + 0xf7, 0x1f, 0xca, 0x08, + 0x80, 0xb9, 0xd8, 0x78, + 0x08, 0x65, 0xca, 0x00, + 0x01, 0x65, 0x3e, 0x30, + 0x01, 0xb9, 0x1e, 0x30, + 0x7f, 0xb9, 0x0a, 0x08, + 0x01, 0xb9, 0x0a, 0x30, + 0x01, 0x54, 0xca, 0x30, + 0x80, 0xb8, 0xe6, 0x78, + 0x80, 0x65, 0xca, 0x00, + 0x01, 0x65, 0x00, 0x34, + 0x01, 0x54, 0x00, 0x34, + 0x08, 0xb8, 0xee, 0x78, + 0x20, 0x01, 0x02, 0x00, + 0x02, 0xbd, 0x08, 0x34, + 0x01, 0xbd, 0x08, 0x34, + 0x08, 0x01, 0x02, 0x00, + 0x02, 0x0b, 0xf4, 0x78, + 0xf7, 0x01, 0x02, 0x08, + 0x01, 0x06, 0xcc, 0x34, + 0xb2, 0x00, 0x00, 0x08, + 0x01, 0x40, 0x20, 0x31, + 0x01, 0xbf, 0x80, 0x30, + 0x01, 0xb9, 0x7a, 0x30, + 0x3f, 0xba, 0x7c, 0x08, + 0x00, 0x65, 0xea, 0x58, + 0x80, 0x0b, 0xc4, 0x79, + 0x12, 0x01, 0x02, 0x00, + 0x01, 0xab, 0xac, 0x30, + 0xe4, 0x6a, 0x70, 0x5d, + 0x40, 0x6a, 0x16, 0x00, + 0x80, 0x3e, 0x86, 0x5d, + 0x20, 0xb8, 0x18, 0x79, + 0x20, 0x6a, 0x86, 0x5d, + 0x00, 0xab, 0x86, 0x5d, + 0x01, 0xa9, 0x78, 0x30, + 0x10, 0xb8, 0x20, 0x79, + 0xe4, 0x6a, 0x70, 0x5d, + 0x00, 0x65, 0xae, 0x40, + 0x10, 0x03, 0x3c, 0x69, + 0x08, 0x3c, 0x5a, 0x69, + 0x04, 0x3c, 0x92, 0x69, + 0x02, 0x3c, 0x98, 0x69, + 0x01, 0x3c, 0x44, 0x79, + 0xff, 0x6a, 0xa6, 0x00, + 0x00, 0x65, 0xa4, 0x59, + 0x00, 0x6a, 0xc2, 0x5e, + 0xff, 0x53, 0x30, 0x71, + 0x0d, 0x6a, 0x76, 0x00, + 0x00, 0x53, 0x14, 0x5e, + 0x00, 0x65, 0xea, 0x58, + 0x12, 0x01, 0x02, 0x00, + 0x00, 0x65, 0x18, 0x41, + 0xa4, 0x6a, 0x06, 0x00, + 0x00, 0x65, 0xf2, 0x58, + 0xfd, 0x57, 0xae, 0x08, + 0x00, 0x65, 0xae, 0x40, + 0xe4, 0x6a, 0x70, 0x5d, + 0x20, 0x3c, 0x4a, 0x79, + 0x02, 0x6a, 0x86, 0x5d, + 0x04, 0x6a, 0x86, 0x5d, + 0x01, 0x03, 0x4c, 0x69, + 0xf7, 0x11, 0x22, 0x08, + 0xff, 0x6a, 0x24, 0x08, + 0xff, 0x6a, 0x06, 0x08, + 0x01, 0x6a, 0x7e, 0x00, + 0x00, 0x65, 0xa4, 0x59, + 0x00, 0x65, 0x04, 0x40, + 0x80, 0x86, 0xc8, 0x08, + 0x01, 0x4f, 0xc8, 0x30, + 0x00, 0x50, 0x6c, 0x61, + 0xc4, 0x6a, 0x70, 0x5d, + 0x40, 0x3c, 0x68, 0x79, + 0x28, 0x6a, 0x86, 0x5d, + 0x00, 0x65, 0x4c, 0x41, + 0x08, 0x6a, 0x86, 0x5d, + 0x00, 0x65, 0x4c, 0x41, + 0x84, 0x6a, 0x70, 0x5d, + 0x00, 0x65, 0xf2, 0x58, + 0x01, 0x66, 0xc8, 0x30, + 0x01, 0x64, 0xd8, 0x31, + 0x01, 0x64, 0x32, 0x31, + 0x5b, 0x64, 0xc8, 0x28, + 0x30, 0x64, 0xca, 0x18, + 0x01, 0x6c, 0xc8, 0x30, + 0xff, 0x64, 0x8e, 0x79, + 0x08, 0x01, 0x02, 0x00, + 0x02, 0x0b, 0x80, 0x79, + 0x01, 0x64, 0x86, 0x61, + 0xf7, 0x01, 0x02, 0x08, + 0x01, 0x06, 0xd8, 0x31, + 0x01, 0x06, 0x32, 0x31, + 0xff, 0x64, 0xc8, 0x18, + 0xff, 0x64, 0x80, 0x69, + 0xf7, 0x3c, 0x78, 0x08, + 0x00, 0x65, 0x20, 0x41, + 0x40, 0xaa, 0x7e, 0x10, + 0x04, 0xaa, 0x70, 0x5d, + 0x00, 0x65, 0x58, 0x42, + 0xc4, 0x6a, 0x70, 0x5d, + 0xc0, 0x6a, 0x7e, 0x00, + 0x00, 0xa8, 0x86, 0x5d, + 0xe4, 0x6a, 0x06, 0x00, + 0x00, 0x6a, 0x86, 0x5d, + 0x00, 0x65, 0x4c, 0x41, + 0x10, 0x3c, 0xa8, 0x69, + 0x00, 0xbb, 0x8c, 0x44, + 0x18, 0x6a, 0xda, 0x01, + 0x01, 0x69, 0xd8, 0x31, + 0x1c, 0x6a, 0xd0, 0x01, + 0x09, 0xee, 0xdc, 0x01, + 0x80, 0xee, 0xb0, 0x79, + 0xff, 0x6a, 0xdc, 0x09, + 0x01, 0x93, 0x26, 0x01, + 0x03, 0x6a, 0x2a, 0x01, + 0x01, 0x69, 0x32, 0x31, + 0x1c, 0x6a, 0xe2, 0x5d, + 0x0a, 0x93, 0x26, 0x01, + 0x00, 0x65, 0xaa, 0x5e, + 0x01, 0x50, 0xa0, 0x18, + 0x02, 0x6a, 0x22, 0x05, + 0x1a, 0x01, 0x02, 0x00, + 0x80, 0x6a, 0x74, 0x00, + 0x40, 0x6a, 0x78, 0x00, + 0x40, 0x6a, 0x16, 0x00, + 0x00, 0x65, 0xda, 0x5d, + 0x01, 0x3f, 0xc8, 0x30, + 0xbf, 0x64, 0x58, 0x7a, + 0x80, 0x64, 0xa0, 0x73, + 0xa0, 0x64, 0x02, 0x74, + 0xc0, 0x64, 0xf6, 0x73, + 0xe0, 0x64, 0x32, 0x74, + 0x01, 0x6a, 0xda, 0x5e, + 0x00, 0x65, 0xcc, 0x41, + 0xf7, 0x11, 0x22, 0x08, + 0x01, 0x06, 0xd4, 0x30, + 0xff, 0x6a, 0x24, 0x08, + 0xf7, 0x01, 0x02, 0x08, + 0xc0, 0x6a, 0x78, 0x00, + 0x09, 0x0c, 0xe8, 0x79, + 0x08, 0x0c, 0x04, 0x68, + 0xb1, 0x6a, 0xda, 0x5e, + 0xff, 0x6a, 0x26, 0x09, + 0x12, 0x01, 0x02, 0x00, + 0x02, 0x6a, 0x08, 0x30, + 0xff, 0x6a, 0x08, 0x08, + 0xdf, 0x01, 0x02, 0x08, + 0x01, 0x6a, 0x7e, 0x00, + 0xc0, 0x6a, 0x78, 0x04, + 0xff, 0x6a, 0xc8, 0x08, + 0x08, 0xa4, 0x48, 0x19, + 0x00, 0xa5, 0x4a, 0x21, + 0x00, 0xa6, 0x4c, 0x21, + 0x00, 0xa7, 0x4e, 0x25, + 0x08, 0xeb, 0xde, 0x7e, + 0x80, 0xeb, 0x08, 0x7a, + 0xff, 0x6a, 0xd6, 0x09, + 0x08, 0xeb, 0x0c, 0x6a, + 0xff, 0x6a, 0xd4, 0x0c, + 0x80, 0xa3, 0xde, 0x6e, + 0x88, 0xeb, 0x22, 0x72, + 0x08, 0xeb, 0xde, 0x6e, + 0x04, 0xea, 0x26, 0xe2, + 0x08, 0xee, 0xde, 0x6e, + 0x04, 0x6a, 0xd0, 0x81, + 0x05, 0xa4, 0xc0, 0x89, + 0x03, 0xa5, 0xc2, 0x31, + 0x09, 0x6a, 0xd6, 0x05, + 0x00, 0x65, 0x0a, 0x5a, + 0x06, 0xa4, 0xd4, 0x89, + 0x80, 0x94, 0xde, 0x7e, + 0x07, 0xe9, 0x10, 0x31, + 0x01, 0xe9, 0x46, 0x31, + 0x00, 0xa3, 0xbc, 0x5e, + 0x00, 0x65, 0xfc, 0x59, + 0x01, 0xa4, 0xca, 0x30, + 0x80, 0xa3, 0x36, 0x7a, + 0x02, 0x65, 0xca, 0x00, + 0x01, 0x65, 0xf8, 0x31, + 0x80, 0x93, 0x26, 0x01, + 0xff, 0x6a, 0xd4, 0x0c, + 0x01, 0x8c, 0xc8, 0x30, + 0x00, 0x88, 0xc8, 0x18, + 0x02, 0x64, 0xc8, 0x88, + 0xff, 0x64, 0xde, 0x7e, + 0xff, 0x8d, 0x4c, 0x6a, + 0xff, 0x8e, 0x4c, 0x6a, + 0x03, 0x8c, 0xd4, 0x98, + 0x00, 0x65, 0xde, 0x56, + 0x01, 0x64, 0x70, 0x30, + 0xff, 0x64, 0xc8, 0x10, + 0x01, 0x64, 0xc8, 0x18, + 0x00, 0x8c, 0x18, 0x19, + 0xff, 0x8d, 0x1a, 0x21, + 0xff, 0x8e, 0x1c, 0x25, + 0xc0, 0x3c, 0x5c, 0x7a, + 0x21, 0x6a, 0xda, 0x5e, + 0xa8, 0x6a, 0x76, 0x00, + 0x79, 0x6a, 0x76, 0x00, + 0x40, 0x3f, 0x64, 0x6a, + 0x04, 0x3b, 0x76, 0x00, + 0x04, 0x6a, 0xd4, 0x81, + 0x20, 0x3c, 0x6c, 0x7a, + 0x51, 0x6a, 0xda, 0x5e, + 0x00, 0x65, 0x84, 0x42, + 0x20, 0x3c, 0x78, 0x00, + 0x00, 0xb3, 0xbc, 0x5e, + 0x07, 0xac, 0x10, 0x31, + 0x05, 0xb3, 0x46, 0x31, + 0x88, 0x6a, 0xcc, 0x00, + 0xac, 0x6a, 0xf0, 0x5d, + 0xa3, 0x6a, 0xcc, 0x00, + 0xb3, 0x6a, 0xf4, 0x5d, + 0x00, 0x65, 0x3c, 0x5a, + 0xfd, 0xa4, 0x48, 0x09, + 0x03, 0x8c, 0x10, 0x30, + 0x00, 0x65, 0xe8, 0x5d, + 0x01, 0xa4, 0x96, 0x7a, + 0x04, 0x3b, 0x76, 0x08, + 0x01, 0x3b, 0x26, 0x31, + 0x80, 0x02, 0x04, 0x00, + 0x10, 0x0c, 0x8c, 0x7a, + 0x03, 0x9e, 0x8e, 0x6a, + 0x7f, 0x02, 0x04, 0x08, + 0x91, 0x6a, 0xda, 0x5e, + 0x00, 0x65, 0xcc, 0x41, + 0x01, 0xa4, 0xca, 0x30, + 0x80, 0xa3, 0x9c, 0x7a, + 0x02, 0x65, 0xca, 0x00, + 0x01, 0x65, 0xf8, 0x31, + 0x01, 0x3b, 0x26, 0x31, + 0x00, 0x65, 0x10, 0x5a, + 0x01, 0xfc, 0xaa, 0x6a, + 0x80, 0x0b, 0xa0, 0x6a, + 0x10, 0x0c, 0xa0, 0x7a, + 0x20, 0x93, 0xa0, 0x6a, + 0x02, 0x93, 0x26, 0x01, + 0x02, 0xfc, 0xb4, 0x7a, + 0x40, 0x0d, 0xc8, 0x6a, + 0x01, 0xa4, 0x48, 0x01, + 0x00, 0x65, 0xc8, 0x42, + 0x40, 0x0d, 0xba, 0x6a, + 0x00, 0x65, 0x10, 0x5a, + 0x00, 0x65, 0xac, 0x42, + 0x80, 0xfc, 0xc4, 0x7a, + 0x80, 0xa4, 0xc4, 0x6a, + 0xff, 0xa5, 0x4a, 0x19, + 0xff, 0xa6, 0x4c, 0x21, + 0xff, 0xa7, 0x4e, 0x21, + 0xf8, 0xfc, 0x48, 0x09, + 0x7f, 0xa3, 0x46, 0x09, + 0x04, 0x3b, 0xe4, 0x6a, + 0x02, 0x93, 0x26, 0x01, + 0x01, 0x94, 0xca, 0x7a, + 0x01, 0x94, 0xca, 0x7a, + 0x01, 0x94, 0xca, 0x7a, + 0x01, 0x94, 0xca, 0x7a, + 0x01, 0x94, 0xca, 0x7a, + 0x01, 0xa4, 0xe2, 0x7a, + 0x01, 0xfc, 0xd8, 0x7a, + 0x01, 0x94, 0xe4, 0x6a, + 0x01, 0x94, 0xe4, 0x6a, + 0x01, 0x94, 0xe4, 0x6a, + 0x00, 0x65, 0x84, 0x42, + 0x01, 0x94, 0xe2, 0x7a, + 0x10, 0x94, 0xe4, 0x6a, + 0xd7, 0x93, 0x26, 0x09, + 0x28, 0x93, 0xe8, 0x6a, + 0x01, 0x85, 0x0a, 0x01, + 0x02, 0xfc, 0xf0, 0x6a, + 0x01, 0x14, 0x46, 0x31, + 0xff, 0x6a, 0x10, 0x09, + 0xfe, 0x85, 0x0a, 0x09, + 0xff, 0x38, 0xfe, 0x6a, + 0x80, 0xa3, 0xfe, 0x7a, + 0x80, 0x0b, 0xfc, 0x7a, + 0x04, 0x3b, 0xfe, 0x7a, + 0xbf, 0x3b, 0x76, 0x08, + 0x01, 0x3b, 0x26, 0x31, + 0x00, 0x65, 0x10, 0x5a, + 0x01, 0x0b, 0x0c, 0x6b, + 0x10, 0x0c, 0x00, 0x7b, + 0x04, 0x93, 0x0a, 0x6b, + 0x01, 0x94, 0x08, 0x7b, + 0x10, 0x94, 0x0a, 0x6b, + 0xc7, 0x93, 0x26, 0x09, + 0x01, 0x99, 0xd4, 0x30, + 0x38, 0x93, 0x0e, 0x6b, + 0xff, 0x08, 0x5c, 0x6b, + 0xff, 0x09, 0x5c, 0x6b, + 0xff, 0x0a, 0x5c, 0x6b, + 0xff, 0x38, 0x2a, 0x7b, + 0x04, 0x14, 0x10, 0x31, + 0x01, 0x38, 0x18, 0x31, + 0x02, 0x6a, 0x1a, 0x31, + 0x88, 0x6a, 0xcc, 0x00, + 0x14, 0x6a, 0xf6, 0x5d, + 0x00, 0x38, 0xe2, 0x5d, + 0xff, 0x6a, 0x70, 0x08, + 0x00, 0x65, 0x56, 0x43, + 0x80, 0xa3, 0x30, 0x7b, + 0x01, 0xa4, 0x48, 0x01, + 0x00, 0x65, 0x5c, 0x43, + 0x08, 0xeb, 0x36, 0x7b, + 0x00, 0x65, 0x10, 0x5a, + 0x08, 0xeb, 0x32, 0x6b, + 0x07, 0xe9, 0x10, 0x31, + 0x01, 0xe9, 0xca, 0x30, + 0x01, 0x65, 0x46, 0x31, + 0x00, 0x6a, 0xbc, 0x5e, + 0x88, 0x6a, 0xcc, 0x00, + 0xa4, 0x6a, 0xf6, 0x5d, + 0x08, 0x6a, 0xe2, 0x5d, + 0x0d, 0x93, 0x26, 0x01, + 0x00, 0x65, 0xaa, 0x5e, + 0x88, 0x6a, 0xcc, 0x00, + 0x00, 0x65, 0x8c, 0x5e, + 0x01, 0x99, 0x46, 0x31, + 0x00, 0xa3, 0xbc, 0x5e, + 0x01, 0x88, 0x10, 0x31, + 0x00, 0x65, 0x3c, 0x5a, + 0x00, 0x65, 0xfc, 0x59, + 0x03, 0x8c, 0x10, 0x30, + 0x00, 0x65, 0xe8, 0x5d, + 0x80, 0x0b, 0x84, 0x6a, + 0x80, 0x0b, 0x64, 0x6b, + 0x01, 0x0c, 0x5e, 0x7b, + 0x10, 0x0c, 0x84, 0x7a, + 0x03, 0x9e, 0x84, 0x6a, + 0x00, 0x65, 0x06, 0x5a, + 0x00, 0x6a, 0xbc, 0x5e, + 0x01, 0xa4, 0x84, 0x6b, + 0xff, 0x38, 0x7a, 0x7b, + 0x01, 0x38, 0xc8, 0x30, + 0x00, 0x08, 0x40, 0x19, + 0xff, 0x6a, 0xc8, 0x08, + 0x00, 0x09, 0x42, 0x21, + 0x00, 0x0a, 0x44, 0x21, + 0xff, 0x6a, 0x70, 0x08, + 0x00, 0x65, 0x7c, 0x43, + 0x03, 0x08, 0x40, 0x31, + 0x03, 0x08, 0x40, 0x31, + 0x01, 0x08, 0x40, 0x31, + 0x01, 0x09, 0x42, 0x31, + 0x01, 0x0a, 0x44, 0x31, + 0xfd, 0xb4, 0x68, 0x09, + 0x12, 0x01, 0x02, 0x00, + 0x12, 0x01, 0x02, 0x00, + 0x04, 0x3c, 0xcc, 0x79, + 0xfb, 0x3c, 0x78, 0x08, + 0x04, 0x93, 0x20, 0x79, + 0x01, 0x0c, 0x90, 0x6b, + 0x80, 0xba, 0x20, 0x79, + 0x80, 0x04, 0x20, 0x79, + 0xe4, 0x6a, 0x70, 0x5d, + 0x23, 0x6a, 0x86, 0x5d, + 0x01, 0x6a, 0x86, 0x5d, + 0x00, 0x65, 0x20, 0x41, + 0x00, 0x65, 0xcc, 0x41, + 0x80, 0x3c, 0xa4, 0x7b, + 0x21, 0x6a, 0xda, 0x5e, + 0x01, 0xbc, 0x18, 0x31, + 0x02, 0x6a, 0x1a, 0x31, + 0x02, 0x6a, 0xf8, 0x01, + 0x01, 0xbc, 0x10, 0x30, + 0x02, 0x6a, 0x12, 0x30, + 0x01, 0xbc, 0x10, 0x30, + 0xff, 0x6a, 0x12, 0x08, + 0xff, 0x6a, 0x14, 0x08, + 0xf3, 0xbc, 0xd4, 0x18, + 0xa0, 0x6a, 0xca, 0x53, + 0x04, 0xa0, 0x10, 0x31, + 0xac, 0x6a, 0x26, 0x01, + 0x04, 0xa0, 0x10, 0x31, + 0x03, 0x08, 0x18, 0x31, + 0x88, 0x6a, 0xcc, 0x00, + 0xa0, 0x6a, 0xf6, 0x5d, + 0x00, 0xbc, 0xe2, 0x5d, + 0x3d, 0x6a, 0x26, 0x01, + 0x00, 0x65, 0xe2, 0x43, + 0xff, 0x6a, 0x10, 0x09, + 0xa4, 0x6a, 0x26, 0x01, + 0x0c, 0xa0, 0x32, 0x31, + 0x05, 0x6a, 0x26, 0x01, + 0x35, 0x6a, 0x26, 0x01, + 0x0c, 0xa0, 0x32, 0x31, + 0x36, 0x6a, 0x26, 0x01, + 0x02, 0x93, 0x26, 0x01, + 0x35, 0x6a, 0x26, 0x01, + 0x00, 0x65, 0x9e, 0x5e, + 0x00, 0x65, 0x9e, 0x5e, + 0x02, 0x93, 0x26, 0x01, + 0xbf, 0x3c, 0x78, 0x08, + 0x04, 0x0b, 0xe8, 0x6b, + 0x10, 0x0c, 0xe4, 0x7b, + 0x01, 0x03, 0xe8, 0x6b, + 0x20, 0x93, 0xea, 0x6b, + 0x04, 0x0b, 0xf0, 0x6b, + 0x40, 0x3c, 0x78, 0x00, + 0xc7, 0x93, 0x26, 0x09, + 0x38, 0x93, 0xf2, 0x6b, + 0x00, 0x65, 0xcc, 0x41, + 0x80, 0x3c, 0x58, 0x6c, + 0x01, 0x06, 0x50, 0x31, + 0x80, 0xb8, 0x70, 0x01, + 0x00, 0x65, 0xcc, 0x41, + 0x10, 0x3f, 0x06, 0x00, + 0x10, 0x6a, 0x06, 0x00, + 0x01, 0x3a, 0xca, 0x30, + 0x80, 0x65, 0x1e, 0x64, + 0x10, 0xb8, 0x42, 0x6c, + 0xc0, 0x3e, 0xca, 0x00, + 0x40, 0xb8, 0x0e, 0x6c, + 0xbf, 0x65, 0xca, 0x08, + 0x20, 0xb8, 0x22, 0x7c, + 0x01, 0x65, 0x0c, 0x30, + 0x00, 0x65, 0xda, 0x5d, + 0xa0, 0x3f, 0x2a, 0x64, + 0x23, 0xb8, 0x0c, 0x08, + 0x00, 0x65, 0xda, 0x5d, + 0xa0, 0x3f, 0x2a, 0x64, + 0x00, 0xbb, 0x22, 0x44, + 0xff, 0x65, 0x22, 0x64, + 0x00, 0x65, 0x42, 0x44, + 0x40, 0x6a, 0x18, 0x00, + 0x01, 0x65, 0x0c, 0x30, + 0x00, 0x65, 0xda, 0x5d, + 0xa0, 0x3f, 0xfe, 0x73, + 0x40, 0x6a, 0x18, 0x00, + 0x01, 0x3a, 0xa6, 0x30, + 0x08, 0x6a, 0x74, 0x00, + 0x00, 0x65, 0xcc, 0x41, + 0x64, 0x6a, 0x6a, 0x5d, + 0x80, 0x64, 0xda, 0x6c, + 0x04, 0x64, 0x9c, 0x74, + 0x02, 0x64, 0xac, 0x74, + 0x00, 0x6a, 0x62, 0x74, + 0x03, 0x64, 0xca, 0x74, + 0x23, 0x64, 0x4a, 0x74, + 0x08, 0x64, 0x5e, 0x74, + 0x61, 0x6a, 0xda, 0x5e, + 0x00, 0x65, 0xda, 0x5d, + 0x08, 0x51, 0xce, 0x71, + 0x00, 0x65, 0x42, 0x44, + 0x80, 0x04, 0x5c, 0x7c, + 0x51, 0x6a, 0x60, 0x5d, + 0x01, 0x51, 0x5c, 0x64, + 0x01, 0xa4, 0x54, 0x7c, + 0x80, 0xba, 0x5e, 0x6c, + 0x41, 0x6a, 0xda, 0x5e, + 0x00, 0x65, 0x5e, 0x44, + 0x21, 0x6a, 0xda, 0x5e, + 0x00, 0x65, 0x5e, 0x44, + 0x07, 0x6a, 0x56, 0x5d, + 0x01, 0x06, 0xd4, 0x30, + 0x00, 0x65, 0xcc, 0x41, + 0x80, 0xb8, 0x58, 0x7c, + 0xc0, 0x3c, 0x6c, 0x7c, + 0x80, 0x3c, 0x58, 0x6c, + 0xff, 0xa8, 0x6c, 0x6c, + 0x40, 0x3c, 0x58, 0x6c, + 0x10, 0xb8, 0x70, 0x7c, + 0xa1, 0x6a, 0xda, 0x5e, + 0x01, 0xb4, 0x76, 0x6c, + 0x02, 0xb4, 0x78, 0x6c, + 0x01, 0xa4, 0x78, 0x7c, + 0xff, 0xa8, 0x88, 0x7c, + 0x04, 0xb4, 0x68, 0x01, + 0x01, 0x6a, 0x76, 0x00, + 0x00, 0xbb, 0x14, 0x5e, + 0xff, 0xa8, 0x88, 0x7c, + 0x71, 0x6a, 0xda, 0x5e, + 0x40, 0x51, 0x88, 0x64, + 0x00, 0x65, 0xb4, 0x5e, + 0x00, 0x65, 0xde, 0x41, + 0x00, 0xbb, 0x8c, 0x5c, + 0x00, 0x65, 0xde, 0x41, + 0x00, 0x65, 0xb4, 0x5e, + 0x01, 0x65, 0xa2, 0x30, + 0x01, 0xf8, 0xc8, 0x30, + 0x01, 0x4e, 0xc8, 0x30, + 0x00, 0x6a, 0xb8, 0xdd, + 0x00, 0x51, 0xca, 0x5d, + 0x01, 0x4e, 0x9c, 0x18, + 0x02, 0x6a, 0x22, 0x05, + 0xc0, 0x3c, 0x58, 0x6c, + 0x04, 0xb8, 0x70, 0x01, + 0x00, 0x65, 0xd6, 0x5e, + 0x20, 0xb8, 0xde, 0x69, + 0x01, 0xbb, 0xa2, 0x30, + 0x3f, 0xba, 0x7c, 0x08, + 0x00, 0xb9, 0xd0, 0x5c, + 0x00, 0x65, 0xde, 0x41, + 0x01, 0x06, 0xd4, 0x30, + 0x20, 0x3c, 0xcc, 0x79, + 0x20, 0x3c, 0x5e, 0x7c, + 0x01, 0xa4, 0xba, 0x7c, + 0x01, 0xb4, 0x68, 0x01, + 0x00, 0x65, 0xcc, 0x41, + 0x00, 0x65, 0x5e, 0x44, + 0x04, 0x14, 0x58, 0x31, + 0x01, 0x06, 0xd4, 0x30, + 0x08, 0xa0, 0x60, 0x31, + 0xac, 0x6a, 0xcc, 0x00, + 0x14, 0x6a, 0xf6, 0x5d, + 0x01, 0x06, 0xd4, 0x30, + 0xa0, 0x6a, 0xee, 0x5d, + 0x00, 0x65, 0xcc, 0x41, + 0xdf, 0x3c, 0x78, 0x08, + 0x12, 0x01, 0x02, 0x00, + 0x00, 0x65, 0x5e, 0x44, + 0x4c, 0x65, 0xcc, 0x28, + 0x01, 0x3e, 0x20, 0x31, + 0xd0, 0x66, 0xcc, 0x18, + 0x20, 0x66, 0xcc, 0x18, + 0x01, 0x51, 0xda, 0x34, + 0x4c, 0x3d, 0xca, 0x28, + 0x3f, 0x64, 0x7c, 0x08, + 0xd0, 0x65, 0xca, 0x18, + 0x01, 0x3e, 0x20, 0x31, + 0x30, 0x65, 0xd4, 0x18, + 0x00, 0x65, 0xe8, 0x4c, + 0xe1, 0x6a, 0x22, 0x01, + 0xff, 0x6a, 0xd4, 0x08, + 0x20, 0x65, 0xd4, 0x18, + 0x00, 0x65, 0xf0, 0x54, + 0xe1, 0x6a, 0x22, 0x01, + 0xff, 0x6a, 0xd4, 0x08, + 0x20, 0x65, 0xca, 0x18, + 0xe0, 0x65, 0xd4, 0x18, + 0x00, 0x65, 0xfa, 0x4c, + 0xe1, 0x6a, 0x22, 0x01, + 0xff, 0x6a, 0xd4, 0x08, + 0xd0, 0x65, 0xd4, 0x18, + 0x00, 0x65, 0x02, 0x55, + 0xe1, 0x6a, 0x22, 0x01, + 0xff, 0x6a, 0xd4, 0x08, + 0x01, 0x6c, 0xa2, 0x30, + 0xff, 0x51, 0x14, 0x75, + 0x00, 0x51, 0x90, 0x5d, + 0x01, 0x51, 0x20, 0x31, + 0x00, 0x65, 0x36, 0x45, + 0x3f, 0xba, 0xc8, 0x08, + 0x00, 0x3e, 0x36, 0x75, + 0x00, 0x65, 0xb2, 0x5e, + 0x80, 0x3c, 0x78, 0x00, + 0x01, 0x06, 0xd4, 0x30, + 0x00, 0x65, 0xda, 0x5d, + 0x01, 0x3c, 0x78, 0x00, + 0xe0, 0x3f, 0x52, 0x65, + 0x02, 0x3c, 0x78, 0x00, + 0x20, 0x12, 0x52, 0x65, + 0x51, 0x6a, 0x60, 0x5d, + 0x00, 0x51, 0x90, 0x5d, + 0x51, 0x6a, 0x60, 0x5d, + 0x01, 0x51, 0x20, 0x31, + 0x04, 0x3c, 0x78, 0x00, + 0x01, 0xb9, 0xc8, 0x30, + 0x00, 0x3d, 0x50, 0x65, + 0x08, 0x3c, 0x78, 0x00, + 0x3f, 0xba, 0xc8, 0x08, + 0x00, 0x3e, 0x50, 0x65, + 0x10, 0x3c, 0x78, 0x00, + 0x04, 0xb8, 0x50, 0x7d, + 0xfb, 0xb8, 0x70, 0x09, + 0x20, 0xb8, 0x46, 0x6d, + 0x01, 0x90, 0xc8, 0x30, + 0xff, 0x6a, 0xa2, 0x00, + 0x00, 0x3d, 0xd0, 0x5c, + 0x01, 0x64, 0x20, 0x31, + 0xff, 0x6a, 0x78, 0x08, + 0x00, 0x65, 0xea, 0x58, + 0x10, 0xb8, 0x5e, 0x7c, + 0xff, 0x6a, 0x56, 0x5d, + 0x00, 0x65, 0x5e, 0x44, + 0x00, 0x65, 0xb2, 0x5e, + 0x31, 0x6a, 0xda, 0x5e, + 0x00, 0x65, 0x5e, 0x44, + 0x10, 0x3f, 0x06, 0x00, + 0x10, 0x6a, 0x06, 0x00, + 0x01, 0x65, 0x74, 0x34, + 0x81, 0x6a, 0xda, 0x5e, + 0x00, 0x65, 0x62, 0x45, + 0x01, 0x06, 0xd4, 0x30, + 0x01, 0x0c, 0x62, 0x7d, + 0x04, 0x0c, 0x5c, 0x6d, + 0xe0, 0x03, 0x7e, 0x08, + 0xe0, 0x3f, 0xcc, 0x61, + 0x01, 0x65, 0xcc, 0x30, + 0x01, 0x12, 0xda, 0x34, + 0x01, 0x06, 0xd4, 0x34, + 0x01, 0x03, 0x70, 0x6d, + 0x40, 0x03, 0xcc, 0x08, + 0x01, 0x65, 0x06, 0x30, + 0x40, 0x65, 0xc8, 0x08, + 0x00, 0x66, 0x7e, 0x75, + 0x40, 0x65, 0x7e, 0x7d, + 0x00, 0x65, 0x7e, 0x5d, + 0xff, 0x6a, 0xd4, 0x08, + 0xff, 0x6a, 0xd4, 0x08, + 0xff, 0x6a, 0xd4, 0x08, + 0xff, 0x6a, 0xd4, 0x0c, + 0x08, 0x01, 0x02, 0x00, + 0x02, 0x0b, 0x88, 0x7d, + 0x01, 0x65, 0x0c, 0x30, + 0x02, 0x0b, 0x8c, 0x7d, + 0xf7, 0x01, 0x02, 0x0c, + 0x01, 0x65, 0xc8, 0x30, + 0xff, 0x41, 0xb0, 0x75, + 0x01, 0x41, 0x20, 0x31, + 0xff, 0x6a, 0xa4, 0x00, + 0x00, 0x65, 0xa0, 0x45, + 0xff, 0xbf, 0xb0, 0x75, + 0x01, 0x90, 0xa4, 0x30, + 0x01, 0xbf, 0x20, 0x31, + 0x00, 0xbb, 0x9a, 0x65, + 0xff, 0x52, 0xae, 0x75, + 0x01, 0xbf, 0xcc, 0x30, + 0x01, 0x90, 0xca, 0x30, + 0x01, 0x52, 0x20, 0x31, + 0x01, 0x66, 0x7e, 0x31, + 0x01, 0x65, 0x20, 0x35, + 0x01, 0xbf, 0x82, 0x34, + 0x01, 0x64, 0xa2, 0x30, + 0x00, 0x6a, 0xc2, 0x5e, + 0x0d, 0x6a, 0x76, 0x00, + 0x00, 0x51, 0x14, 0x46, + 0x01, 0x65, 0xa4, 0x30, + 0xe0, 0x6a, 0xcc, 0x00, + 0x48, 0x6a, 0x08, 0x5e, + 0x01, 0x6a, 0xd0, 0x01, + 0x01, 0x6a, 0xdc, 0x05, + 0x88, 0x6a, 0xcc, 0x00, + 0x48, 0x6a, 0x08, 0x5e, + 0x01, 0x6a, 0xe2, 0x5d, + 0x01, 0x6a, 0x26, 0x05, + 0x01, 0x65, 0xd8, 0x31, + 0x09, 0xee, 0xdc, 0x01, + 0x80, 0xee, 0xce, 0x7d, + 0xff, 0x6a, 0xdc, 0x0d, + 0x01, 0x65, 0x32, 0x31, + 0x0a, 0x93, 0x26, 0x01, + 0x00, 0x65, 0xaa, 0x46, + 0x81, 0x6a, 0xda, 0x5e, + 0x01, 0x0c, 0xda, 0x7d, + 0x04, 0x0c, 0xd8, 0x6d, + 0xe0, 0x03, 0x06, 0x08, + 0xe0, 0x03, 0x7e, 0x0c, + 0x01, 0x65, 0x18, 0x31, + 0xff, 0x6a, 0x1a, 0x09, + 0xff, 0x6a, 0x1c, 0x0d, + 0x01, 0x8c, 0x10, 0x30, + 0x01, 0x8d, 0x12, 0x30, + 0x01, 0x8e, 0x14, 0x34, + 0x01, 0x6c, 0xda, 0x30, + 0x01, 0x6c, 0xda, 0x30, + 0x01, 0x6c, 0xda, 0x30, + 0x01, 0x6c, 0xda, 0x30, + 0x01, 0x6c, 0xda, 0x30, + 0x01, 0x6c, 0xda, 0x30, + 0x01, 0x6c, 0xda, 0x30, + 0x01, 0x6c, 0xda, 0x34, + 0x3d, 0x64, 0xa4, 0x28, + 0x55, 0x64, 0xc8, 0x28, + 0x00, 0x65, 0x08, 0x46, + 0x2e, 0x64, 0xa4, 0x28, + 0x66, 0x64, 0xc8, 0x28, + 0x00, 0x6c, 0xda, 0x18, + 0x01, 0x52, 0xc8, 0x30, + 0x00, 0x6c, 0xda, 0x20, + 0xff, 0x6a, 0xc8, 0x08, + 0x00, 0x6c, 0xda, 0x20, + 0x00, 0x6c, 0xda, 0x24, + 0x01, 0x65, 0xc8, 0x30, + 0xe0, 0x6a, 0xcc, 0x00, + 0x44, 0x6a, 0x04, 0x5e, + 0x01, 0x90, 0xe2, 0x31, + 0x04, 0x3b, 0x28, 0x7e, + 0x30, 0x6a, 0xd0, 0x01, + 0x20, 0x6a, 0xd0, 0x01, + 0x1d, 0x6a, 0xdc, 0x01, + 0xdc, 0xee, 0x24, 0x66, + 0x00, 0x65, 0x40, 0x46, + 0x20, 0x6a, 0xd0, 0x01, + 0x01, 0x6a, 0xdc, 0x01, + 0x20, 0xa0, 0xd8, 0x31, + 0x09, 0xee, 0xdc, 0x01, + 0x80, 0xee, 0x30, 0x7e, + 0x11, 0x6a, 0xdc, 0x01, + 0x50, 0xee, 0x34, 0x66, + 0x20, 0x6a, 0xd0, 0x01, + 0x09, 0x6a, 0xdc, 0x01, + 0x88, 0xee, 0x3a, 0x66, + 0x19, 0x6a, 0xdc, 0x01, + 0xd8, 0xee, 0x3e, 0x66, + 0xff, 0x6a, 0xdc, 0x09, + 0x18, 0xee, 0x42, 0x6e, + 0xff, 0x6a, 0xd4, 0x0c, + 0x88, 0x6a, 0xcc, 0x00, + 0x44, 0x6a, 0x04, 0x5e, + 0x20, 0x6a, 0xe2, 0x5d, + 0x01, 0x3b, 0x26, 0x31, + 0x04, 0x3b, 0x5c, 0x6e, + 0xa0, 0x6a, 0xca, 0x00, + 0x20, 0x65, 0xc8, 0x18, + 0x00, 0x65, 0x9a, 0x5e, + 0x00, 0x65, 0x54, 0x66, + 0x0a, 0x93, 0x26, 0x01, + 0x00, 0x65, 0xaa, 0x46, + 0xa0, 0x6a, 0xcc, 0x00, + 0xff, 0x6a, 0xc8, 0x08, + 0x20, 0x94, 0x60, 0x6e, + 0x10, 0x94, 0x62, 0x6e, + 0x08, 0x94, 0x7c, 0x6e, + 0x08, 0x94, 0x7c, 0x6e, + 0x08, 0x94, 0x7c, 0x6e, + 0xff, 0x8c, 0xc8, 0x10, + 0xc1, 0x64, 0xc8, 0x18, + 0xf8, 0x64, 0xc8, 0x08, + 0x01, 0x99, 0xda, 0x30, + 0x00, 0x66, 0x70, 0x66, + 0xc0, 0x66, 0xac, 0x76, + 0x60, 0x66, 0xc8, 0x18, + 0x3d, 0x64, 0xc8, 0x28, + 0x00, 0x65, 0x60, 0x46, + 0xf7, 0x93, 0x26, 0x09, + 0x08, 0x93, 0x7e, 0x6e, + 0x00, 0x62, 0xc4, 0x18, + 0x00, 0x65, 0xaa, 0x5e, + 0x00, 0x65, 0x8a, 0x5e, + 0x00, 0x65, 0x8a, 0x5e, + 0x00, 0x65, 0x8a, 0x5e, + 0x01, 0x99, 0xda, 0x30, + 0x01, 0x99, 0xda, 0x30, + 0x01, 0x99, 0xda, 0x30, + 0x01, 0x99, 0xda, 0x30, + 0x01, 0x99, 0xda, 0x30, + 0x01, 0x99, 0xda, 0x30, + 0x01, 0x99, 0xda, 0x30, + 0x01, 0x99, 0xda, 0x34, + 0x01, 0x6c, 0x32, 0x31, + 0x01, 0x6c, 0x32, 0x31, + 0x01, 0x6c, 0x32, 0x31, + 0x01, 0x6c, 0x32, 0x31, + 0x01, 0x6c, 0x32, 0x31, + 0x01, 0x6c, 0x32, 0x31, + 0x01, 0x6c, 0x32, 0x31, + 0x01, 0x6c, 0x32, 0x35, + 0x08, 0x94, 0xaa, 0x7e, + 0xf7, 0x93, 0x26, 0x09, + 0x08, 0x93, 0xae, 0x6e, + 0xff, 0x6a, 0xd4, 0x0c, + 0x04, 0xb8, 0xd6, 0x6e, + 0x01, 0x42, 0x7e, 0x31, + 0xff, 0x6a, 0x76, 0x01, + 0x01, 0x90, 0x84, 0x34, + 0xff, 0x6a, 0x76, 0x05, + 0x01, 0x85, 0x0a, 0x01, + 0x7f, 0x65, 0x10, 0x09, + 0xfe, 0x85, 0x0a, 0x0d, + 0xff, 0x42, 0xd2, 0x66, + 0xff, 0x41, 0xca, 0x66, + 0xd1, 0x6a, 0xda, 0x5e, + 0xff, 0x6a, 0xca, 0x04, + 0x01, 0x41, 0x20, 0x31, + 0x01, 0xbf, 0x82, 0x30, + 0x01, 0x6a, 0x76, 0x00, + 0x00, 0xbb, 0x14, 0x46, + 0x01, 0x42, 0x20, 0x31, + 0x01, 0xbf, 0x84, 0x34, + 0x01, 0x41, 0x7e, 0x31, + 0x01, 0x90, 0x82, 0x34, + 0x01, 0x65, 0x22, 0x31, + 0xff, 0x6a, 0xd4, 0x08, + 0xff, 0x6a, 0xd4, 0x0c +}; + +typedef int ahc_patch_func_t (struct ahc_softc *ahc); +static ahc_patch_func_t ahc_patch23_func; + +static int +ahc_patch23_func(struct ahc_softc *ahc) +{ + return ((ahc->bugs & AHC_SCBCHAN_UPLOAD_BUG) != 0); +} + +static ahc_patch_func_t ahc_patch22_func; + +static int +ahc_patch22_func(struct ahc_softc *ahc) +{ + return ((ahc->features & AHC_CMD_CHAN) == 0); +} + +static ahc_patch_func_t ahc_patch21_func; + +static int +ahc_patch21_func(struct ahc_softc *ahc) +{ + return ((ahc->features & AHC_QUEUE_REGS) == 0); +} + +static ahc_patch_func_t ahc_patch20_func; + +static int +ahc_patch20_func(struct ahc_softc *ahc) +{ + return ((ahc->features & AHC_WIDE) != 0); +} + +static ahc_patch_func_t ahc_patch19_func; + +static int +ahc_patch19_func(struct ahc_softc *ahc) +{ + return ((ahc->flags & AHC_SCB_BTT) != 0); +} + +static ahc_patch_func_t ahc_patch18_func; + +static int +ahc_patch18_func(struct ahc_softc *ahc) +{ + return ((ahc->bugs & AHC_PCI_2_1_RETRY_BUG) != 0); +} + +static ahc_patch_func_t ahc_patch17_func; + +static int +ahc_patch17_func(struct ahc_softc *ahc) +{ + return ((ahc->bugs & AHC_TMODE_WIDEODD_BUG) != 0); +} + +static ahc_patch_func_t ahc_patch16_func; + +static int +ahc_patch16_func(struct ahc_softc *ahc) +{ + return ((ahc->bugs & AHC_AUTOFLUSH_BUG) != 0); +} + +static ahc_patch_func_t ahc_patch15_func; + +static int +ahc_patch15_func(struct ahc_softc *ahc) +{ + return ((ahc->features & AHC_ULTRA2) == 0); +} + +static ahc_patch_func_t ahc_patch14_func; + +static int +ahc_patch14_func(struct ahc_softc *ahc) +{ + return ((ahc->bugs & AHC_PCI_MWI_BUG) != 0 && ahc->pci_cachesize != 0); +} + +static ahc_patch_func_t ahc_patch13_func; + +static int +ahc_patch13_func(struct ahc_softc *ahc) +{ + return ((ahc->flags & AHC_39BIT_ADDRESSING) != 0); +} + +static ahc_patch_func_t ahc_patch12_func; + +static int +ahc_patch12_func(struct ahc_softc *ahc) +{ + return ((ahc->features & AHC_HS_MAILBOX) != 0); +} + +static ahc_patch_func_t ahc_patch11_func; + +static int +ahc_patch11_func(struct ahc_softc *ahc) +{ + return ((ahc->features & AHC_ULTRA) != 0); +} + +static ahc_patch_func_t ahc_patch10_func; + +static int +ahc_patch10_func(struct ahc_softc *ahc) +{ + return ((ahc->features & AHC_MULTI_TID) != 0); +} + +static ahc_patch_func_t ahc_patch9_func; + +static int +ahc_patch9_func(struct ahc_softc *ahc) +{ + return ((ahc->features & AHC_CMD_CHAN) != 0); +} + +static ahc_patch_func_t ahc_patch8_func; + +static int +ahc_patch8_func(struct ahc_softc *ahc) +{ + return ((ahc->flags & AHC_INITIATORROLE) != 0); +} + +static ahc_patch_func_t ahc_patch7_func; + +static int +ahc_patch7_func(struct ahc_softc *ahc) +{ + return ((ahc->flags & AHC_TARGETROLE) != 0); +} + +static ahc_patch_func_t ahc_patch6_func; + +static int +ahc_patch6_func(struct ahc_softc *ahc) +{ + return ((ahc->features & AHC_DT) == 0); +} + +static ahc_patch_func_t ahc_patch5_func; + +static int +ahc_patch5_func(struct ahc_softc *ahc) +{ + return ((ahc->flags & AHC_SEQUENCER_DEBUG) != 0); +} + +static ahc_patch_func_t ahc_patch4_func; + +static int +ahc_patch4_func(struct ahc_softc *ahc) +{ + return ((ahc->flags & AHC_PAGESCBS) != 0); +} + +static ahc_patch_func_t ahc_patch3_func; + +static int +ahc_patch3_func(struct ahc_softc *ahc) +{ + return ((ahc->features & AHC_QUEUE_REGS) != 0); +} + +static ahc_patch_func_t ahc_patch2_func; + +static int +ahc_patch2_func(struct ahc_softc *ahc) +{ + return ((ahc->features & AHC_TWIN) != 0); +} + +static ahc_patch_func_t ahc_patch1_func; + +static int +ahc_patch1_func(struct ahc_softc *ahc) +{ + return ((ahc->features & AHC_ULTRA2) != 0); +} + +static ahc_patch_func_t ahc_patch0_func; + +static int +ahc_patch0_func(struct ahc_softc *ahc) +{ + return (0); +} + +static const struct patch { + ahc_patch_func_t *patch_func; + uint32_t begin :10, + skip_instr :10, + skip_patch :12; +} patches[] = { + { ahc_patch1_func, 4, 1, 1 }, + { ahc_patch2_func, 6, 2, 1 }, + { ahc_patch2_func, 9, 1, 1 }, + { ahc_patch3_func, 11, 1, 2 }, + { ahc_patch0_func, 12, 2, 1 }, + { ahc_patch4_func, 15, 1, 2 }, + { ahc_patch0_func, 16, 1, 1 }, + { ahc_patch5_func, 22, 2, 1 }, + { ahc_patch3_func, 27, 1, 2 }, + { ahc_patch0_func, 28, 1, 1 }, + { ahc_patch6_func, 34, 1, 1 }, + { ahc_patch7_func, 37, 54, 19 }, + { ahc_patch8_func, 37, 1, 1 }, + { ahc_patch9_func, 42, 3, 2 }, + { ahc_patch0_func, 45, 3, 1 }, + { ahc_patch10_func, 49, 1, 2 }, + { ahc_patch0_func, 50, 2, 3 }, + { ahc_patch1_func, 50, 1, 2 }, + { ahc_patch0_func, 51, 1, 1 }, + { ahc_patch2_func, 53, 2, 1 }, + { ahc_patch9_func, 55, 1, 2 }, + { ahc_patch0_func, 56, 1, 1 }, + { ahc_patch9_func, 60, 1, 2 }, + { ahc_patch0_func, 61, 1, 1 }, + { ahc_patch9_func, 71, 1, 2 }, + { ahc_patch0_func, 72, 1, 1 }, + { ahc_patch9_func, 75, 1, 2 }, + { ahc_patch0_func, 76, 1, 1 }, + { ahc_patch9_func, 79, 1, 2 }, + { ahc_patch0_func, 80, 1, 1 }, + { ahc_patch8_func, 91, 9, 4 }, + { ahc_patch1_func, 93, 1, 2 }, + { ahc_patch0_func, 94, 1, 1 }, + { ahc_patch2_func, 96, 2, 1 }, + { ahc_patch2_func, 105, 4, 1 }, + { ahc_patch1_func, 109, 1, 2 }, + { ahc_patch0_func, 110, 2, 3 }, + { ahc_patch2_func, 110, 1, 2 }, + { ahc_patch0_func, 111, 1, 1 }, + { ahc_patch7_func, 112, 4, 2 }, + { ahc_patch0_func, 116, 1, 1 }, + { ahc_patch11_func, 117, 2, 1 }, + { ahc_patch1_func, 119, 1, 2 }, + { ahc_patch0_func, 120, 1, 1 }, + { ahc_patch7_func, 121, 4, 1 }, + { ahc_patch7_func, 131, 95, 11 }, + { ahc_patch4_func, 151, 1, 1 }, + { ahc_patch1_func, 168, 1, 1 }, + { ahc_patch12_func, 173, 1, 2 }, + { ahc_patch0_func, 174, 1, 1 }, + { ahc_patch9_func, 185, 1, 2 }, + { ahc_patch0_func, 186, 1, 1 }, + { ahc_patch9_func, 195, 1, 2 }, + { ahc_patch0_func, 196, 1, 1 }, + { ahc_patch9_func, 212, 6, 2 }, + { ahc_patch0_func, 218, 6, 1 }, + { ahc_patch8_func, 226, 21, 2 }, + { ahc_patch1_func, 241, 1, 1 }, + { ahc_patch1_func, 249, 1, 2 }, + { ahc_patch0_func, 250, 2, 2 }, + { ahc_patch11_func, 251, 1, 1 }, + { ahc_patch9_func, 259, 27, 3 }, + { ahc_patch1_func, 275, 10, 2 }, + { ahc_patch13_func, 278, 1, 1 }, + { ahc_patch14_func, 286, 14, 1 }, + { ahc_patch1_func, 302, 1, 2 }, + { ahc_patch0_func, 303, 1, 1 }, + { ahc_patch9_func, 306, 1, 1 }, + { ahc_patch13_func, 311, 1, 1 }, + { ahc_patch9_func, 312, 2, 2 }, + { ahc_patch0_func, 314, 4, 1 }, + { ahc_patch14_func, 318, 1, 1 }, + { ahc_patch15_func, 320, 2, 3 }, + { ahc_patch9_func, 320, 1, 2 }, + { ahc_patch0_func, 321, 1, 1 }, + { ahc_patch6_func, 326, 1, 2 }, + { ahc_patch0_func, 327, 1, 1 }, + { ahc_patch1_func, 331, 47, 11 }, + { ahc_patch6_func, 338, 2, 4 }, + { ahc_patch7_func, 338, 1, 1 }, + { ahc_patch8_func, 339, 1, 1 }, + { ahc_patch0_func, 340, 1, 1 }, + { ahc_patch16_func, 341, 1, 1 }, + { ahc_patch6_func, 357, 6, 3 }, + { ahc_patch16_func, 357, 5, 1 }, + { ahc_patch0_func, 363, 7, 1 }, + { ahc_patch13_func, 373, 5, 1 }, + { ahc_patch0_func, 378, 52, 17 }, + { ahc_patch14_func, 378, 1, 1 }, + { ahc_patch7_func, 380, 2, 2 }, + { ahc_patch17_func, 381, 1, 1 }, + { ahc_patch9_func, 384, 1, 1 }, + { ahc_patch18_func, 391, 1, 1 }, + { ahc_patch14_func, 396, 9, 3 }, + { ahc_patch9_func, 397, 3, 2 }, + { ahc_patch0_func, 400, 3, 1 }, + { ahc_patch9_func, 408, 6, 2 }, + { ahc_patch0_func, 414, 9, 2 }, + { ahc_patch13_func, 414, 1, 1 }, + { ahc_patch13_func, 423, 2, 1 }, + { ahc_patch14_func, 425, 1, 1 }, + { ahc_patch9_func, 427, 1, 2 }, + { ahc_patch0_func, 428, 1, 1 }, + { ahc_patch7_func, 429, 1, 1 }, + { ahc_patch7_func, 430, 1, 1 }, + { ahc_patch8_func, 431, 3, 3 }, + { ahc_patch6_func, 432, 1, 2 }, + { ahc_patch0_func, 433, 1, 1 }, + { ahc_patch9_func, 434, 1, 1 }, + { ahc_patch15_func, 435, 1, 2 }, + { ahc_patch13_func, 435, 1, 1 }, + { ahc_patch14_func, 437, 9, 4 }, + { ahc_patch9_func, 437, 1, 1 }, + { ahc_patch9_func, 444, 2, 1 }, + { ahc_patch0_func, 446, 4, 3 }, + { ahc_patch9_func, 446, 1, 2 }, + { ahc_patch0_func, 447, 3, 1 }, + { ahc_patch1_func, 451, 2, 1 }, + { ahc_patch7_func, 453, 10, 2 }, + { ahc_patch0_func, 463, 1, 1 }, + { ahc_patch8_func, 464, 118, 22 }, + { ahc_patch1_func, 466, 3, 2 }, + { ahc_patch0_func, 469, 5, 3 }, + { ahc_patch9_func, 469, 2, 2 }, + { ahc_patch0_func, 471, 3, 1 }, + { ahc_patch1_func, 476, 2, 2 }, + { ahc_patch0_func, 478, 6, 3 }, + { ahc_patch9_func, 478, 2, 2 }, + { ahc_patch0_func, 480, 3, 1 }, + { ahc_patch1_func, 486, 2, 2 }, + { ahc_patch0_func, 488, 9, 7 }, + { ahc_patch9_func, 488, 5, 6 }, + { ahc_patch19_func, 488, 1, 2 }, + { ahc_patch0_func, 489, 1, 1 }, + { ahc_patch19_func, 491, 1, 2 }, + { ahc_patch0_func, 492, 1, 1 }, + { ahc_patch0_func, 493, 4, 1 }, + { ahc_patch6_func, 498, 3, 2 }, + { ahc_patch0_func, 501, 1, 1 }, + { ahc_patch6_func, 511, 1, 2 }, + { ahc_patch0_func, 512, 1, 1 }, + { ahc_patch20_func, 549, 7, 1 }, + { ahc_patch3_func, 584, 1, 2 }, + { ahc_patch0_func, 585, 1, 1 }, + { ahc_patch21_func, 588, 1, 1 }, + { ahc_patch8_func, 590, 106, 33 }, + { ahc_patch4_func, 592, 1, 1 }, + { ahc_patch1_func, 598, 2, 2 }, + { ahc_patch0_func, 600, 1, 1 }, + { ahc_patch1_func, 603, 1, 2 }, + { ahc_patch0_func, 604, 1, 1 }, + { ahc_patch9_func, 605, 3, 3 }, + { ahc_patch15_func, 606, 1, 1 }, + { ahc_patch0_func, 608, 4, 1 }, + { ahc_patch19_func, 617, 2, 2 }, + { ahc_patch0_func, 619, 1, 1 }, + { ahc_patch19_func, 623, 10, 3 }, + { ahc_patch5_func, 625, 8, 1 }, + { ahc_patch0_func, 633, 9, 2 }, + { ahc_patch5_func, 634, 8, 1 }, + { ahc_patch4_func, 644, 1, 2 }, + { ahc_patch0_func, 645, 1, 1 }, + { ahc_patch19_func, 646, 1, 2 }, + { ahc_patch0_func, 647, 3, 2 }, + { ahc_patch4_func, 649, 1, 1 }, + { ahc_patch5_func, 650, 1, 1 }, + { ahc_patch5_func, 653, 1, 1 }, + { ahc_patch5_func, 655, 1, 1 }, + { ahc_patch4_func, 657, 2, 2 }, + { ahc_patch0_func, 659, 2, 1 }, + { ahc_patch5_func, 661, 1, 1 }, + { ahc_patch5_func, 664, 1, 1 }, + { ahc_patch5_func, 667, 1, 1 }, + { ahc_patch19_func, 671, 1, 1 }, + { ahc_patch19_func, 674, 1, 1 }, + { ahc_patch4_func, 680, 1, 1 }, + { ahc_patch6_func, 683, 1, 2 }, + { ahc_patch0_func, 684, 1, 1 }, + { ahc_patch7_func, 696, 16, 1 }, + { ahc_patch4_func, 712, 20, 1 }, + { ahc_patch9_func, 733, 4, 2 }, + { ahc_patch0_func, 737, 4, 1 }, + { ahc_patch9_func, 741, 4, 2 }, + { ahc_patch0_func, 745, 3, 1 }, + { ahc_patch6_func, 751, 1, 1 }, + { ahc_patch22_func, 753, 14, 1 }, + { ahc_patch7_func, 767, 3, 1 }, + { ahc_patch9_func, 779, 24, 8 }, + { ahc_patch19_func, 783, 1, 2 }, + { ahc_patch0_func, 784, 1, 1 }, + { ahc_patch15_func, 789, 4, 2 }, + { ahc_patch0_func, 793, 7, 3 }, + { ahc_patch23_func, 793, 5, 2 }, + { ahc_patch0_func, 798, 2, 1 }, + { ahc_patch0_func, 803, 42, 3 }, + { ahc_patch18_func, 815, 18, 2 }, + { ahc_patch0_func, 833, 1, 1 }, + { ahc_patch4_func, 857, 1, 1 }, + { ahc_patch4_func, 858, 3, 2 }, + { ahc_patch0_func, 861, 1, 1 }, + { ahc_patch13_func, 862, 3, 1 }, + { ahc_patch4_func, 865, 12, 1 } +}; + +static const struct cs { + uint16_t begin; + uint16_t end; +} critical_sections[] = { + { 11, 18 }, + { 21, 30 }, + { 712, 728 }, + { 858, 861 }, + { 865, 871 }, + { 873, 875 }, + { 875, 877 } +}; + +#define NUM_CRITICAL_SECTIONS ARRAY_SIZE(critical_sections) diff --git a/drivers/scsi/aic7xxx/aicasm/Makefile b/drivers/scsi/aic7xxx/aicasm/Makefile new file mode 100644 index 000000000..243adb0a3 --- /dev/null +++ b/drivers/scsi/aic7xxx/aicasm/Makefile @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: GPL-2.0 +PROG= aicasm + +OUTDIR ?= ./ + +.SUFFIXES= .l .y .c .h + +CSRCS= aicasm.c aicasm_symbol.c +YSRCS= aicasm_gram.y aicasm_macro_gram.y +LSRCS= aicasm_scan.l aicasm_macro_scan.l + +GENHDRS= $(addprefix ${OUTDIR}/,aicdb.h $(YSRCS:.y=.h)) +GENSRCS= $(addprefix ${OUTDIR}/,$(YSRCS:.y=.c) $(LSRCS:.l=.c)) + +SRCS= ${CSRCS} ${GENSRCS} +LIBS= -ldb +clean-files:= ${GENSRCS} ${GENHDRS} $(YSRCS:.y=.output) $(PROG) +# Override default kernel CFLAGS. This is a userland app. +AICASM_CFLAGS:= -I/usr/include -I. -I$(OUTDIR) +LEX= flex +YACC= bison +YFLAGS= -d + +NOMAN= noman + +ifneq ($(HOSTCC),) +AICASM_CC= $(HOSTCC) +else +AICASM_CC= $(CC) +endif + +ifdef DEBUG +CFLAGS+= -DDEBUG -g +YFLAGS+= -t -v +LFLAGS= -d +endif + +$(PROG): $(OUTDIR) ${GENHDRS} $(SRCS) + $(AICASM_CC) $(AICASM_CFLAGS) $(SRCS) -o $(OUTDIR)/$(PROG) $(LIBS) + +$(OUTDIR): + mkdir -p $(OUTDIR) + +$(OUTDIR)/aicdb.h: + @if [ -e "/usr/include/db4/db_185.h" ]; then \ + echo "#include <db4/db_185.h>" > $@; \ + elif [ -e "/usr/include/db3/db_185.h" ]; then \ + echo "#include <db3/db_185.h>" > $@; \ + elif [ -e "/usr/include/db2/db_185.h" ]; then \ + echo "#include <db2/db_185.h>" > $@; \ + elif [ -e "/usr/include/db1/db_185.h" ]; then \ + echo "#include <db1/db_185.h>" > $@; \ + elif [ -e "/usr/include/db/db_185.h" ]; then \ + echo "#include <db/db_185.h>" > $@; \ + elif [ -e "/usr/include/db_185.h" ]; then \ + echo "#include <db_185.h>" > $@; \ + else \ + echo "*** Install db development libraries"; \ + fi + +clean: + rm -f $(clean-files) + +# Create a dependency chain in generated files +# to avoid concurrent invocations of the single +# rule that builds them all. +$(OUTDIR)/aicasm_gram.c: $(OUTDIR)/aicasm_gram.h +$(OUTDIR)/aicasm_gram.c $(OUTDIR)/aicasm_gram.h: aicasm_gram.y + $(YACC) $(YFLAGS) -b $(<:.y=) $< + mv $(<:.y=).tab.c $(OUTDIR)/$(<:.y=.c) + mv $(<:.y=).tab.h $(OUTDIR)/$(<:.y=.h) + +# Create a dependency chain in generated files +# to avoid concurrent invocations of the single +# rule that builds them all. +$(OUTDIR)/aicasm_macro_gram.c: $(OUTDIR)/aicasm_macro_gram.h +$(OUTDIR)/aicasm_macro_gram.c $(OUTDIR)/aicasm_macro_gram.h: aicasm_macro_gram.y + $(YACC) $(YFLAGS) -b $(<:.y=) -p mm $< + mv $(<:.y=).tab.c $(OUTDIR)/$(<:.y=.c) + mv $(<:.y=).tab.h $(OUTDIR)/$(<:.y=.h) + +$(OUTDIR)/aicasm_scan.c: aicasm_scan.l + $(LEX) $(LFLAGS) -o $@ $< + +$(OUTDIR)/aicasm_macro_scan.c: aicasm_macro_scan.l + $(LEX) $(LFLAGS) -Pmm -o $@ $< diff --git a/drivers/scsi/aic7xxx/aicasm/aicasm.c b/drivers/scsi/aic7xxx/aicasm/aicasm.c new file mode 100644 index 000000000..5f474e490 --- /dev/null +++ b/drivers/scsi/aic7xxx/aicasm/aicasm.c @@ -0,0 +1,843 @@ +/* + * Aic7xxx SCSI host adapter firmware assembler + * + * Copyright (c) 1997, 1998, 2000, 2001 Justin T. Gibbs. + * Copyright (c) 2001, 2002 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aicasm/aicasm.c#23 $ + * + * $FreeBSD$ + */ +#include <sys/types.h> +#include <sys/mman.h> + +#include <ctype.h> +#include <inttypes.h> +#include <regex.h> +#include <stdio.h> +#include <stdlib.h> +#include <string.h> +#include <sysexits.h> +#include <unistd.h> + +#if linux +#include <endian.h> +#else +#include <machine/endian.h> +#endif + +#include "aicasm.h" +#include "aicasm_symbol.h" +#include "aicasm_insformat.h" + +typedef struct patch { + STAILQ_ENTRY(patch) links; + int patch_func; + u_int begin; + u_int skip_instr; + u_int skip_patch; +} patch_t; + +STAILQ_HEAD(patch_list, patch) patches; + +static void usage(void); +static void back_patch(void); +static void output_code(void); +static void output_listing(char *ifilename); +static void dump_scope(scope_t *scope); +static void emit_patch(scope_t *scope, int patch); +static int check_patch(patch_t **start_patch, int start_instr, + int *skip_addr, int *func_vals); + +struct path_list search_path; +int includes_search_curdir; +char *appname; +char *stock_include_file; +FILE *ofile; +char *ofilename; +char *regfilename; +FILE *regfile; +char *listfilename; +FILE *listfile; +char *regdiagfilename; +FILE *regdiagfile; +int src_mode; +int dst_mode; + +static STAILQ_HEAD(,instruction) seq_program; +struct cs_tailq cs_tailq; +struct scope_list scope_stack; +symlist_t patch_functions; + +#if DEBUG +extern int yy_flex_debug; +extern int mm_flex_debug; +extern int yydebug; +extern int mmdebug; +#endif +extern FILE *yyin; +extern int yyparse(void); + +int main(int argc, char *argv[]); + +int +main(int argc, char *argv[]) +{ + extern char *optarg; + extern int optind; + int ch; + int retval; + char *inputfilename; + scope_t *sentinal; + + STAILQ_INIT(&patches); + SLIST_INIT(&search_path); + STAILQ_INIT(&seq_program); + TAILQ_INIT(&cs_tailq); + SLIST_INIT(&scope_stack); + + /* Set Sentinal scope node */ + sentinal = scope_alloc(); + sentinal->type = SCOPE_ROOT; + + includes_search_curdir = 1; + appname = *argv; + regfile = NULL; + listfile = NULL; +#if DEBUG + yy_flex_debug = 0; + mm_flex_debug = 0; + yydebug = 0; + mmdebug = 0; +#endif + while ((ch = getopt(argc, argv, "d:i:l:n:o:p:r:I:")) != -1) { + switch(ch) { + case 'd': +#if DEBUG + if (strcmp(optarg, "s") == 0) { + yy_flex_debug = 1; + mm_flex_debug = 1; + } else if (strcmp(optarg, "p") == 0) { + yydebug = 1; + mmdebug = 1; + } else { + fprintf(stderr, "%s: -d Requires either an " + "'s' or 'p' argument\n", appname); + usage(); + } +#else + stop("-d: Assembler not built with debugging " + "information", EX_SOFTWARE); +#endif + break; + case 'i': + stock_include_file = optarg; + break; + case 'l': + /* Create a program listing */ + if ((listfile = fopen(optarg, "w")) == NULL) { + perror(optarg); + stop(NULL, EX_CANTCREAT); + } + listfilename = optarg; + break; + case 'n': + /* Don't complain about the -nostdinc directrive */ + if (strcmp(optarg, "ostdinc")) { + fprintf(stderr, "%s: Unknown option -%c%s\n", + appname, ch, optarg); + usage(); + /* NOTREACHED */ + } + break; + case 'o': + if ((ofile = fopen(optarg, "w")) == NULL) { + perror(optarg); + stop(NULL, EX_CANTCREAT); + } + ofilename = optarg; + break; + case 'p': + /* Create Register Diagnostic "printing" Functions */ + if ((regdiagfile = fopen(optarg, "w")) == NULL) { + perror(optarg); + stop(NULL, EX_CANTCREAT); + } + regdiagfilename = optarg; + break; + case 'r': + if ((regfile = fopen(optarg, "w")) == NULL) { + perror(optarg); + stop(NULL, EX_CANTCREAT); + } + regfilename = optarg; + break; + case 'I': + { + path_entry_t include_dir; + + if (strcmp(optarg, "-") == 0) { + if (includes_search_curdir == 0) { + fprintf(stderr, "%s: Warning - '-I-' " + "specified multiple " + "times\n", appname); + } + includes_search_curdir = 0; + for (include_dir = SLIST_FIRST(&search_path); + include_dir != NULL; + include_dir = SLIST_NEXT(include_dir, + links)) + /* + * All entries before a '-I-' only + * apply to includes specified with + * quotes instead of "<>". + */ + include_dir->quoted_includes_only = 1; + } else { + include_dir = + (path_entry_t)malloc(sizeof(*include_dir)); + if (include_dir == NULL) { + perror(optarg); + stop(NULL, EX_OSERR); + } + include_dir->directory = strdup(optarg); + if (include_dir->directory == NULL) { + perror(optarg); + stop(NULL, EX_OSERR); + } + include_dir->quoted_includes_only = 0; + SLIST_INSERT_HEAD(&search_path, include_dir, + links); + } + break; + } + case '?': + default: + usage(); + /* NOTREACHED */ + } + } + argc -= optind; + argv += optind; + + if (argc != 1) { + fprintf(stderr, "%s: No input file specified\n", appname); + usage(); + /* NOTREACHED */ + } + + if (regdiagfile != NULL + && (regfile == NULL || stock_include_file == NULL)) { + fprintf(stderr, + "%s: The -p option requires the -r and -i options.\n", + appname); + usage(); + /* NOTREACHED */ + } + symtable_open(); + inputfilename = *argv; + include_file(*argv, SOURCE_FILE); + retval = yyparse(); + if (retval == 0) { + if (SLIST_FIRST(&scope_stack) == NULL + || SLIST_FIRST(&scope_stack)->type != SCOPE_ROOT) { + stop("Unterminated conditional expression", EX_DATAERR); + /* NOTREACHED */ + } + + /* Process outmost scope */ + process_scope(SLIST_FIRST(&scope_stack)); + /* + * Decend the tree of scopes and insert/emit + * patches as appropriate. We perform a depth first + * tranversal, recursively handling each scope. + */ + /* start at the root scope */ + dump_scope(SLIST_FIRST(&scope_stack)); + + /* Patch up forward jump addresses */ + back_patch(); + + if (ofile != NULL) + output_code(); + if (regfile != NULL) + symtable_dump(regfile, regdiagfile); + if (listfile != NULL) + output_listing(inputfilename); + } + + stop(NULL, 0); + /* NOTREACHED */ + return (0); +} + +static void +usage() +{ + + (void)fprintf(stderr, +"usage: %-16s [-nostdinc] [-I-] [-I directory] [-o output_file]\n" +" [-r register_output_file [-p register_diag_file -i includefile]]\n" +" [-l program_list_file]\n" +" input_file\n", appname); + exit(EX_USAGE); +} + +static void +back_patch() +{ + struct instruction *cur_instr; + + for (cur_instr = STAILQ_FIRST(&seq_program); + cur_instr != NULL; + cur_instr = STAILQ_NEXT(cur_instr, links)) { + if (cur_instr->patch_label != NULL) { + struct ins_format3 *f3_instr; + u_int address; + + if (cur_instr->patch_label->type != LABEL) { + char buf[255]; + + snprintf(buf, sizeof(buf), + "Undefined label %s", + cur_instr->patch_label->name); + stop(buf, EX_DATAERR); + /* NOTREACHED */ + } + f3_instr = &cur_instr->format.format3; + address = f3_instr->address; + address += cur_instr->patch_label->info.linfo->address; + f3_instr->address = address; + } + } +} + +static void +output_code() +{ + struct instruction *cur_instr; + patch_t *cur_patch; + critical_section_t *cs; + symbol_node_t *cur_node; + int instrcount; + + instrcount = 0; + fprintf(ofile, +"/*\n" +" * DO NOT EDIT - This file is automatically generated\n" +" * from the following source files:\n" +" *\n" +"%s */\n", versions); + + fprintf(ofile, "static const uint8_t seqprog[] = {\n"); + for (cur_instr = STAILQ_FIRST(&seq_program); + cur_instr != NULL; + cur_instr = STAILQ_NEXT(cur_instr, links)) { + + fprintf(ofile, "%s\t0x%02x, 0x%02x, 0x%02x, 0x%02x", + cur_instr == STAILQ_FIRST(&seq_program) ? "" : ",\n", +#ifdef __LITTLE_ENDIAN + cur_instr->format.bytes[0], + cur_instr->format.bytes[1], + cur_instr->format.bytes[2], + cur_instr->format.bytes[3]); +#else + cur_instr->format.bytes[3], + cur_instr->format.bytes[2], + cur_instr->format.bytes[1], + cur_instr->format.bytes[0]); +#endif + instrcount++; + } + fprintf(ofile, "\n};\n\n"); + + if (patch_arg_list == NULL) + stop("Patch argument list not defined", + EX_DATAERR); + + /* + * Output patch information. Patch functions first. + */ + fprintf(ofile, +"typedef int %spatch_func_t (%s);\n", prefix, patch_arg_list); + + for (cur_node = SLIST_FIRST(&patch_functions); + cur_node != NULL; + cur_node = SLIST_NEXT(cur_node,links)) { + fprintf(ofile, +"static %spatch_func_t %spatch%d_func;\n" +"\n" +"static int\n" +"%spatch%d_func(%s)\n" +"{\n" +" return (%s);\n" +"}\n\n", + prefix, + prefix, + cur_node->symbol->info.condinfo->func_num, + prefix, + cur_node->symbol->info.condinfo->func_num, + patch_arg_list, + cur_node->symbol->name); + } + + fprintf(ofile, +"static const struct patch {\n" +" %spatch_func_t *patch_func;\n" +" uint32_t begin :10,\n" +" skip_instr :10,\n" +" skip_patch :12;\n" +"} patches[] = {\n", prefix); + + for (cur_patch = STAILQ_FIRST(&patches); + cur_patch != NULL; + cur_patch = STAILQ_NEXT(cur_patch,links)) { + fprintf(ofile, "%s\t{ %spatch%d_func, %d, %d, %d }", + cur_patch == STAILQ_FIRST(&patches) ? "" : ",\n", + prefix, + cur_patch->patch_func, cur_patch->begin, + cur_patch->skip_instr, cur_patch->skip_patch); + } + + fprintf(ofile, "\n};\n\n"); + + fprintf(ofile, +"static const struct cs {\n" +" uint16_t begin;\n" +" uint16_t end;\n" +"} critical_sections[] = {\n"); + + for (cs = TAILQ_FIRST(&cs_tailq); + cs != NULL; + cs = TAILQ_NEXT(cs, links)) { + fprintf(ofile, "%s\t{ %d, %d }", + cs == TAILQ_FIRST(&cs_tailq) ? "" : ",\n", + cs->begin_addr, cs->end_addr); + } + + fprintf(ofile, "\n};\n\n"); + + fprintf(ofile, + "#define NUM_CRITICAL_SECTIONS ARRAY_SIZE(critical_sections)\n"); + + fprintf(stderr, "%s: %d instructions used\n", appname, instrcount); +} + +static void +dump_scope(scope_t *scope) +{ + scope_t *cur_scope; + + /* + * Emit the first patch for this scope + */ + emit_patch(scope, 0); + + /* + * Dump each scope within this one. + */ + cur_scope = TAILQ_FIRST(&scope->inner_scope); + + while (cur_scope != NULL) { + + dump_scope(cur_scope); + + cur_scope = TAILQ_NEXT(cur_scope, scope_links); + } + + /* + * Emit the second, closing, patch for this scope + */ + emit_patch(scope, 1); +} + +void +emit_patch(scope_t *scope, int patch) +{ + patch_info_t *pinfo; + patch_t *new_patch; + + pinfo = &scope->patches[patch]; + + if (pinfo->skip_instr == 0) + /* No-Op patch */ + return; + + new_patch = (patch_t *)malloc(sizeof(*new_patch)); + + if (new_patch == NULL) + stop("Could not malloc patch structure", EX_OSERR); + + memset(new_patch, 0, sizeof(*new_patch)); + + if (patch == 0) { + new_patch->patch_func = scope->func_num; + new_patch->begin = scope->begin_addr; + } else { + new_patch->patch_func = 0; + new_patch->begin = scope->end_addr; + } + new_patch->skip_instr = pinfo->skip_instr; + new_patch->skip_patch = pinfo->skip_patch; + STAILQ_INSERT_TAIL(&patches, new_patch, links); +} + +void +output_listing(char *ifilename) +{ + char buf[1024]; + FILE *ifile; + struct instruction *cur_instr; + patch_t *cur_patch; + symbol_node_t *cur_func; + int *func_values; + int instrcount; + int instrptr; + int line; + int func_count; + int skip_addr; + + instrcount = 0; + instrptr = 0; + line = 1; + skip_addr = 0; + if ((ifile = fopen(ifilename, "r")) == NULL) { + perror(ifilename); + stop(NULL, EX_DATAERR); + } + + /* + * Determine which options to apply to this listing. + */ + for (func_count = 0, cur_func = SLIST_FIRST(&patch_functions); + cur_func != NULL; + cur_func = SLIST_NEXT(cur_func, links)) + func_count++; + + func_values = NULL; + if (func_count != 0) { + func_values = (int *)malloc(func_count * sizeof(int)); + + if (func_values == NULL) + stop("Could not malloc", EX_OSERR); + + func_values[0] = 0; /* FALSE func */ + func_count--; + + /* + * Ask the user to fill in the return values for + * the rest of the functions. + */ + + + for (cur_func = SLIST_FIRST(&patch_functions); + cur_func != NULL && SLIST_NEXT(cur_func, links) != NULL; + cur_func = SLIST_NEXT(cur_func, links), func_count--) { + int input; + + fprintf(stdout, "\n(%s)\n", cur_func->symbol->name); + fprintf(stdout, + "Enter the return value for " + "this expression[T/F]:"); + + while (1) { + + input = getchar(); + input = toupper(input); + + if (input == 'T') { + func_values[func_count] = 1; + break; + } else if (input == 'F') { + func_values[func_count] = 0; + break; + } + } + if (isatty(fileno(stdin)) == 0) + putchar(input); + } + fprintf(stdout, "\nThanks!\n"); + } + + /* Now output the listing */ + cur_patch = STAILQ_FIRST(&patches); + for (cur_instr = STAILQ_FIRST(&seq_program); + cur_instr != NULL; + cur_instr = STAILQ_NEXT(cur_instr, links), instrcount++) { + + if (check_patch(&cur_patch, instrcount, + &skip_addr, func_values) == 0) { + /* Don't count this instruction as it is in a patch + * that was removed. + */ + continue; + } + + while (line < cur_instr->srcline) { + fgets(buf, sizeof(buf), ifile); + fprintf(listfile, " \t%s", buf); + line++; + } + fprintf(listfile, "%04x %02x%02x%02x%02x", instrptr, +#ifdef __LITTLE_ENDIAN + cur_instr->format.bytes[0], + cur_instr->format.bytes[1], + cur_instr->format.bytes[2], + cur_instr->format.bytes[3]); +#else + cur_instr->format.bytes[3], + cur_instr->format.bytes[2], + cur_instr->format.bytes[1], + cur_instr->format.bytes[0]); +#endif + /* + * Macro expansions can cause several instructions + * to be output for a single source line. Only + * advance the line once in these cases. + */ + if (line == cur_instr->srcline) { + fgets(buf, sizeof(buf), ifile); + fprintf(listfile, "\t%s", buf); + line++; + } else { + fprintf(listfile, "\n"); + } + instrptr++; + } + /* Dump the remainder of the file */ + while(fgets(buf, sizeof(buf), ifile) != NULL) + fprintf(listfile, " %s", buf); + + fclose(ifile); +} + +static int +check_patch(patch_t **start_patch, int start_instr, + int *skip_addr, int *func_vals) +{ + patch_t *cur_patch; + + cur_patch = *start_patch; + + while (cur_patch != NULL && start_instr == cur_patch->begin) { + if (func_vals[cur_patch->patch_func] == 0) { + int skip; + + /* Start rejecting code */ + *skip_addr = start_instr + cur_patch->skip_instr; + for (skip = cur_patch->skip_patch; + skip > 0 && cur_patch != NULL; + skip--) + cur_patch = STAILQ_NEXT(cur_patch, links); + } else { + /* Accepted this patch. Advance to the next + * one and wait for our intruction pointer to + * hit this point. + */ + cur_patch = STAILQ_NEXT(cur_patch, links); + } + } + + *start_patch = cur_patch; + if (start_instr < *skip_addr) + /* Still skipping */ + return (0); + + return (1); +} + +/* + * Print out error information if appropriate, and clean up before + * terminating the program. + */ +void +stop(const char *string, int err_code) +{ + if (string != NULL) { + fprintf(stderr, "%s: ", appname); + if (yyfilename != NULL) { + fprintf(stderr, "Stopped at file %s, line %d - ", + yyfilename, yylineno); + } + fprintf(stderr, "%s\n", string); + } + + if (ofile != NULL) { + fclose(ofile); + if (err_code != 0) { + fprintf(stderr, "%s: Removing %s due to error\n", + appname, ofilename); + unlink(ofilename); + } + } + + if (regfile != NULL) { + fclose(regfile); + if (err_code != 0) { + fprintf(stderr, "%s: Removing %s due to error\n", + appname, regfilename); + unlink(regfilename); + } + } + + if (listfile != NULL) { + fclose(listfile); + if (err_code != 0) { + fprintf(stderr, "%s: Removing %s due to error\n", + appname, listfilename); + unlink(listfilename); + } + } + + symlist_free(&patch_functions); + symtable_close(); + + exit(err_code); +} + +struct instruction * +seq_alloc() +{ + struct instruction *new_instr; + + new_instr = (struct instruction *)malloc(sizeof(struct instruction)); + if (new_instr == NULL) + stop("Unable to malloc instruction object", EX_SOFTWARE); + memset(new_instr, 0, sizeof(*new_instr)); + STAILQ_INSERT_TAIL(&seq_program, new_instr, links); + new_instr->srcline = yylineno; + return new_instr; +} + +critical_section_t * +cs_alloc() +{ + critical_section_t *new_cs; + + new_cs= (critical_section_t *)malloc(sizeof(critical_section_t)); + if (new_cs == NULL) + stop("Unable to malloc critical_section object", EX_SOFTWARE); + memset(new_cs, 0, sizeof(*new_cs)); + + TAILQ_INSERT_TAIL(&cs_tailq, new_cs, links); + return new_cs; +} + +scope_t * +scope_alloc() +{ + scope_t *new_scope; + + new_scope = (scope_t *)malloc(sizeof(scope_t)); + if (new_scope == NULL) + stop("Unable to malloc scope object", EX_SOFTWARE); + memset(new_scope, 0, sizeof(*new_scope)); + TAILQ_INIT(&new_scope->inner_scope); + + if (SLIST_FIRST(&scope_stack) != NULL) { + TAILQ_INSERT_TAIL(&SLIST_FIRST(&scope_stack)->inner_scope, + new_scope, scope_links); + } + /* This patch is now the current scope */ + SLIST_INSERT_HEAD(&scope_stack, new_scope, scope_stack_links); + return new_scope; +} + +void +process_scope(scope_t *scope) +{ + /* + * We are "leaving" this scope. We should now have + * enough information to process the lists of scopes + * we encapsulate. + */ + scope_t *cur_scope; + u_int skip_patch_count; + u_int skip_instr_count; + + cur_scope = TAILQ_LAST(&scope->inner_scope, scope_tailq); + skip_patch_count = 0; + skip_instr_count = 0; + while (cur_scope != NULL) { + u_int patch0_patch_skip; + + patch0_patch_skip = 0; + switch (cur_scope->type) { + case SCOPE_IF: + case SCOPE_ELSE_IF: + if (skip_instr_count != 0) { + /* Create a tail patch */ + patch0_patch_skip++; + cur_scope->patches[1].skip_patch = + skip_patch_count + 1; + cur_scope->patches[1].skip_instr = + skip_instr_count; + } + + /* Count Head patch */ + patch0_patch_skip++; + + /* Count any patches contained in our inner scope */ + patch0_patch_skip += cur_scope->inner_scope_patches; + + cur_scope->patches[0].skip_patch = patch0_patch_skip; + cur_scope->patches[0].skip_instr = + cur_scope->end_addr - cur_scope->begin_addr; + + skip_instr_count += cur_scope->patches[0].skip_instr; + + skip_patch_count += patch0_patch_skip; + if (cur_scope->type == SCOPE_IF) { + scope->inner_scope_patches += skip_patch_count; + skip_patch_count = 0; + skip_instr_count = 0; + } + break; + case SCOPE_ELSE: + /* Count any patches contained in our innter scope */ + skip_patch_count += cur_scope->inner_scope_patches; + + skip_instr_count += cur_scope->end_addr + - cur_scope->begin_addr; + break; + case SCOPE_ROOT: + stop("Unexpected scope type encountered", EX_SOFTWARE); + /* NOTREACHED */ + } + + cur_scope = TAILQ_PREV(cur_scope, scope_tailq, scope_links); + } +} diff --git a/drivers/scsi/aic7xxx/aicasm/aicasm.h b/drivers/scsi/aic7xxx/aicasm/aicasm.h new file mode 100644 index 000000000..716a2aefc --- /dev/null +++ b/drivers/scsi/aic7xxx/aicasm/aicasm.h @@ -0,0 +1,91 @@ +/* + * Assembler for the sequencer program downloaded to Aic7xxx SCSI host adapters + * + * Copyright (c) 1997 Justin T. Gibbs. + * Copyright (c) 2001, 2002 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aicasm/aicasm.h#14 $ + * + * $FreeBSD$ + */ + +#include "../queue.h" + +#ifndef TRUE +#define TRUE 1 +#endif + +#ifndef FALSE +#define FALSE 0 +#endif + +typedef struct path_entry { + char *directory; + int quoted_includes_only; + SLIST_ENTRY(path_entry) links; +} *path_entry_t; + +typedef enum { + QUOTED_INCLUDE, + BRACKETED_INCLUDE, + SOURCE_FILE +} include_type; + +SLIST_HEAD(path_list, path_entry); + +extern struct path_list search_path; +extern struct cs_tailq cs_tailq; +extern struct scope_list scope_stack; +extern struct symlist patch_functions; +extern int includes_search_curdir; /* False if we've seen -I- */ +extern char *appname; +extern char *stock_include_file; +extern int yylineno; +extern char *yyfilename; +extern char *prefix; +extern char *patch_arg_list; +extern char *versions; +extern int src_mode; +extern int dst_mode; +struct symbol; + +void stop(const char *errstring, int err_code); +void include_file(char *file_name, include_type type); +void expand_macro(struct symbol *macro_symbol); +struct instruction *seq_alloc(void); +struct critical_section *cs_alloc(void); +struct scope *scope_alloc(void); +void process_scope(struct scope *); diff --git a/drivers/scsi/aic7xxx/aicasm/aicasm_gram.y b/drivers/scsi/aic7xxx/aicasm/aicasm_gram.y new file mode 100644 index 000000000..924d55a8a --- /dev/null +++ b/drivers/scsi/aic7xxx/aicasm/aicasm_gram.y @@ -0,0 +1,2000 @@ +%{ +/* + * Parser for the Aic7xxx SCSI Host adapter sequencer assembler. + * + * Copyright (c) 1997, 1998, 2000 Justin T. Gibbs. + * Copyright (c) 2001, 2002 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aicasm/aicasm_gram.y#30 $ + * + * $FreeBSD$ + */ + +#include <sys/types.h> + +#include <inttypes.h> +#include <regex.h> +#include <stdio.h> +#include <stdlib.h> +#include <string.h> +#include <sysexits.h> + +#include "../queue.h" + +#include "aicasm.h" +#include "aicasm_symbol.h" +#include "aicasm_insformat.h" + +int yylineno; +char *yyfilename; +char stock_prefix[] = "aic_"; +char *prefix = stock_prefix; +char *patch_arg_list; +char *versions; +static char errbuf[255]; +static char regex_pattern[255]; +static symbol_t *cur_symbol; +static symbol_t *field_symbol; +static symbol_t *scb_or_sram_symbol; +static symtype cur_symtype; +static symbol_ref_t accumulator; +static symbol_ref_t mode_ptr; +static symbol_ref_t allones; +static symbol_ref_t allzeros; +static symbol_ref_t none; +static symbol_ref_t sindex; +static int instruction_ptr; +static int num_srams; +static int sram_or_scb_offset; +static int download_constant_count; +static int in_critical_section; +static u_int enum_increment; +static u_int enum_next_value; + +static void process_field(int field_type, symbol_t *sym, int mask); +static void initialize_symbol(symbol_t *symbol); +static void add_macro_arg(const char *argtext, int position); +static void add_macro_body(const char *bodytext); +static void process_register(symbol_t **p_symbol); +static void format_1_instr(int opcode, symbol_ref_t *dest, + expression_t *immed, symbol_ref_t *src, int ret); +static void format_2_instr(int opcode, symbol_ref_t *dest, + expression_t *places, symbol_ref_t *src, int ret); +static void format_3_instr(int opcode, symbol_ref_t *src, + expression_t *immed, symbol_ref_t *address); +static void test_readable_symbol(symbol_t *symbol); +static void test_writable_symbol(symbol_t *symbol); +static void type_check(symbol_ref_t *sym, expression_t *expression, int and_op); +static void make_expression(expression_t *immed, int value); +static void add_conditional(symbol_t *symbol); +static void add_version(const char *verstring); +static int is_download_const(expression_t *immed); +static int is_location_address(symbol_t *symbol); +void yyerror(const char *string); + +#define SRAM_SYMNAME "SRAM_BASE" +#define SCB_SYMNAME "SCB_BASE" +%} + +%union { + u_int value; + char *str; + symbol_t *sym; + symbol_ref_t sym_ref; + expression_t expression; +} + +%token T_REGISTER + +%token <value> T_CONST + +%token T_EXPORT + +%token T_DOWNLOAD + +%token T_SCB + +%token T_SRAM + +%token T_ALIAS + +%token T_SIZE + +%token T_EXPR_LSHIFT + +%token T_EXPR_RSHIFT + +%token <value> T_ADDRESS + +%token T_COUNT + +%token T_ACCESS_MODE + +%token T_DONT_GENERATE_DEBUG_CODE + +%token T_MODES + +%token T_DEFINE + +%token T_SET_SRC_MODE + +%token T_SET_DST_MODE + +%token <value> T_MODE + +%token T_BEGIN_CS + +%token T_END_CS + +%token T_PAD_PAGE + +%token T_FIELD + +%token T_ENUM + +%token T_MASK + +%token <value> T_NUMBER + +%token <str> T_PATH T_STRING T_ARG T_MACROBODY + +%token <sym> T_CEXPR + +%token T_EOF T_INCLUDE T_VERSION T_PREFIX T_PATCH_ARG_LIST + +%token <value> T_SHR T_SHL T_ROR T_ROL + +%token <value> T_MVI T_MOV T_CLR T_BMOV + +%token <value> T_JMP T_JC T_JNC T_JE T_JNE T_JNZ T_JZ T_CALL + +%token <value> T_ADD T_ADC + +%token <value> T_INC T_DEC + +%token <value> T_STC T_CLC + +%token <value> T_CMP T_NOT T_XOR + +%token <value> T_TEST T_AND + +%token <value> T_OR + +/* 16 bit extensions, not implemented + * %token <value> T_OR16 T_AND16 T_XOR16 T_ADD16 + * %token <value> T_ADC16 T_MVI16 T_TEST16 T_CMP16 T_CMPXCHG + */ +%token T_RET + +%token T_NOP + +%token T_ACCUM T_ALLONES T_ALLZEROS T_NONE T_SINDEX T_MODE_PTR + +%token T_A + +%token <sym> T_SYMBOL + +%token T_NL + +%token T_IF T_ELSE T_ELSE_IF T_ENDIF + +%type <sym_ref> reg_symbol address destination source opt_source + +%type <expression> expression immediate immediate_or_a + +%type <value> export ret f1_opcode f2_opcode jmp_jc_jnc_call jz_jnz je_jne + +%type <value> mode_value mode_list macro_arglist + +%left '|' +%left '&' +%left T_EXPR_LSHIFT T_EXPR_RSHIFT +%left '+' '-' +%left '*' '/' +%right '~' +%nonassoc UMINUS +%% + +program: + include +| program include +| prefix +| program prefix +| patch_arg_list +| program patch_arg_list +| version +| program version +| register +| program register +| constant +| program constant +| macrodefn +| program macrodefn +| scratch_ram +| program scratch_ram +| scb +| program scb +| label +| program label +| set_src_mode +| program set_src_mode +| set_dst_mode +| program set_dst_mode +| critical_section_start +| program critical_section_start +| critical_section_end +| program critical_section_end +| conditional +| program conditional +| code +| program code +; + +include: + T_INCLUDE '<' T_PATH '>' + { + include_file($3, BRACKETED_INCLUDE); + } +| T_INCLUDE '"' T_PATH '"' + { + include_file($3, QUOTED_INCLUDE); + } +; + +prefix: + T_PREFIX '=' T_STRING + { + if (prefix != stock_prefix) + stop("Prefix multiply defined", + EX_DATAERR); + prefix = strdup($3); + if (prefix == NULL) + stop("Unable to record prefix", EX_SOFTWARE); + } +; + +patch_arg_list: + T_PATCH_ARG_LIST '=' T_STRING + { + if (patch_arg_list != NULL) + stop("Patch argument list multiply defined", + EX_DATAERR); + patch_arg_list = strdup($3); + if (patch_arg_list == NULL) + stop("Unable to record patch arg list", EX_SOFTWARE); + } +; + +version: + T_VERSION '=' T_STRING + { add_version($3); } +; + +register: + T_REGISTER { cur_symtype = REGISTER; } reg_definition +; + +reg_definition: + T_SYMBOL '{' + { + if ($1->type != UNINITIALIZED) { + stop("Register multiply defined", EX_DATAERR); + /* NOTREACHED */ + } + cur_symbol = $1; + cur_symbol->type = cur_symtype; + initialize_symbol(cur_symbol); + } + reg_attribute_list + '}' + { + /* + * Default to allowing everything in for registers + * with no bit or mask definitions. + */ + if (cur_symbol->info.rinfo->valid_bitmask == 0) + cur_symbol->info.rinfo->valid_bitmask = 0xFF; + + if (cur_symbol->info.rinfo->size == 0) + cur_symbol->info.rinfo->size = 1; + + /* + * This might be useful for registers too. + */ + if (cur_symbol->type != REGISTER) { + if (cur_symbol->info.rinfo->address == 0) + cur_symbol->info.rinfo->address = + sram_or_scb_offset; + sram_or_scb_offset += + cur_symbol->info.rinfo->size; + } + cur_symbol = NULL; + } +; + +reg_attribute_list: + reg_attribute +| reg_attribute_list reg_attribute +; + +reg_attribute: + reg_address +| size +| count +| access_mode +| dont_generate_debug_code +| modes +| field_defn +| enum_defn +| mask_defn +| alias +| accumulator +| mode_pointer +| allones +| allzeros +| none +| sindex +; + +reg_address: + T_ADDRESS T_NUMBER + { + cur_symbol->info.rinfo->address = $2; + } +; + +size: + T_SIZE T_NUMBER + { + cur_symbol->info.rinfo->size = $2; + if (scb_or_sram_symbol != NULL) { + u_int max_addr; + u_int sym_max_addr; + + max_addr = scb_or_sram_symbol->info.rinfo->address + + scb_or_sram_symbol->info.rinfo->size; + sym_max_addr = cur_symbol->info.rinfo->address + + cur_symbol->info.rinfo->size; + + if (sym_max_addr > max_addr) + stop("SCB or SRAM space exhausted", EX_DATAERR); + } + } +; + +count: + T_COUNT T_NUMBER + { + cur_symbol->count += $2; + } +; + +access_mode: + T_ACCESS_MODE T_MODE + { + cur_symbol->info.rinfo->mode = $2; + } +; + +dont_generate_debug_code: + T_DONT_GENERATE_DEBUG_CODE + { + cur_symbol->dont_generate_debug_code = 1; + } +; + +modes: + T_MODES mode_list + { + cur_symbol->info.rinfo->modes = $2; + } +; + +mode_list: + mode_value + { + $$ = $1; + } +| mode_list ',' mode_value + { + $$ = $1 | $3; + } +; + +mode_value: + T_NUMBER + { + if ($1 > 4) { + stop("Valid register modes range between 0 and 4.", + EX_DATAERR); + /* NOTREACHED */ + } + + $$ = (0x1 << $1); + } +| T_SYMBOL + { + symbol_t *symbol; + + symbol = $1; + if (symbol->type != CONST) { + stop("Only \"const\" symbols allowed in " + "mode definitions.", EX_DATAERR); + /* NOTREACHED */ + } + if (symbol->info.cinfo->value > 4) { + stop("Valid register modes range between 0 and 4.", + EX_DATAERR); + /* NOTREACHED */ + } + $$ = (0x1 << symbol->info.cinfo->value); + } +; + +field_defn: + T_FIELD + { + field_symbol = NULL; + enum_next_value = 0; + enum_increment = 1; + } + '{' enum_entry_list '}' +| T_FIELD T_SYMBOL expression + { + process_field(FIELD, $2, $3.value); + field_symbol = $2; + enum_next_value = 0; + enum_increment = 0x01 << (ffs($3.value) - 1); + } + '{' enum_entry_list '}' +| T_FIELD T_SYMBOL expression + { + process_field(FIELD, $2, $3.value); + } +; + +enum_defn: + T_ENUM + { + field_symbol = NULL; + enum_next_value = 0; + enum_increment = 1; + } + '{' enum_entry_list '}' +| T_ENUM T_SYMBOL expression + { + process_field(ENUM, $2, $3.value); + field_symbol = $2; + enum_next_value = 0; + enum_increment = 0x01 << (ffs($3.value) - 1); + } + '{' enum_entry_list '}' +; + +enum_entry_list: + enum_entry +| enum_entry_list ',' enum_entry +; + +enum_entry: + T_SYMBOL + { + process_field(ENUM_ENTRY, $1, enum_next_value); + enum_next_value += enum_increment; + } +| T_SYMBOL expression + { + process_field(ENUM_ENTRY, $1, $2.value); + enum_next_value = $2.value + enum_increment; + } +; + +mask_defn: + T_MASK T_SYMBOL expression + { + process_field(MASK, $2, $3.value); + } +; + +alias: + T_ALIAS T_SYMBOL + { + if ($2->type != UNINITIALIZED) { + stop("Re-definition of register alias", + EX_DATAERR); + /* NOTREACHED */ + } + $2->type = ALIAS; + initialize_symbol($2); + $2->info.ainfo->parent = cur_symbol; + } +; + +accumulator: + T_ACCUM + { + if (accumulator.symbol != NULL) { + stop("Only one accumulator definition allowed", + EX_DATAERR); + /* NOTREACHED */ + } + accumulator.symbol = cur_symbol; + } +; + +mode_pointer: + T_MODE_PTR + { + if (mode_ptr.symbol != NULL) { + stop("Only one mode pointer definition allowed", + EX_DATAERR); + /* NOTREACHED */ + } + mode_ptr.symbol = cur_symbol; + } +; + +allones: + T_ALLONES + { + if (allones.symbol != NULL) { + stop("Only one definition of allones allowed", + EX_DATAERR); + /* NOTREACHED */ + } + allones.symbol = cur_symbol; + } +; + +allzeros: + T_ALLZEROS + { + if (allzeros.symbol != NULL) { + stop("Only one definition of allzeros allowed", + EX_DATAERR); + /* NOTREACHED */ + } + allzeros.symbol = cur_symbol; + } +; + +none: + T_NONE + { + if (none.symbol != NULL) { + stop("Only one definition of none allowed", + EX_DATAERR); + /* NOTREACHED */ + } + none.symbol = cur_symbol; + } +; + +sindex: + T_SINDEX + { + if (sindex.symbol != NULL) { + stop("Only one definition of sindex allowed", + EX_DATAERR); + /* NOTREACHED */ + } + sindex.symbol = cur_symbol; + } +; + +expression: + expression '|' expression + { + $$.value = $1.value | $3.value; + symlist_merge(&$$.referenced_syms, + &$1.referenced_syms, + &$3.referenced_syms); + } +| expression '&' expression + { + $$.value = $1.value & $3.value; + symlist_merge(&$$.referenced_syms, + &$1.referenced_syms, + &$3.referenced_syms); + } +| expression '+' expression + { + $$.value = $1.value + $3.value; + symlist_merge(&$$.referenced_syms, + &$1.referenced_syms, + &$3.referenced_syms); + } +| expression '-' expression + { + $$.value = $1.value - $3.value; + symlist_merge(&($$.referenced_syms), + &($1.referenced_syms), + &($3.referenced_syms)); + } +| expression '*' expression + { + $$.value = $1.value * $3.value; + symlist_merge(&($$.referenced_syms), + &($1.referenced_syms), + &($3.referenced_syms)); + } +| expression '/' expression + { + $$.value = $1.value / $3.value; + symlist_merge(&($$.referenced_syms), + &($1.referenced_syms), + &($3.referenced_syms)); + } +| expression T_EXPR_LSHIFT expression + { + $$.value = $1.value << $3.value; + symlist_merge(&$$.referenced_syms, + &$1.referenced_syms, + &$3.referenced_syms); + } +| expression T_EXPR_RSHIFT expression + { + $$.value = $1.value >> $3.value; + symlist_merge(&$$.referenced_syms, + &$1.referenced_syms, + &$3.referenced_syms); + } +| '(' expression ')' + { + $$ = $2; + } +| '~' expression + { + $$ = $2; + $$.value = (~$$.value) & 0xFF; + } +| '-' expression %prec UMINUS + { + $$ = $2; + $$.value = -$$.value; + } +| T_NUMBER + { + $$.value = $1; + SLIST_INIT(&$$.referenced_syms); + } +| T_SYMBOL + { + symbol_t *symbol; + + symbol = $1; + switch (symbol->type) { + case ALIAS: + symbol = $1->info.ainfo->parent; + case REGISTER: + case SCBLOC: + case SRAMLOC: + $$.value = symbol->info.rinfo->address; + break; + case MASK: + case FIELD: + case ENUM: + case ENUM_ENTRY: + $$.value = symbol->info.finfo->value; + break; + case DOWNLOAD_CONST: + case CONST: + $$.value = symbol->info.cinfo->value; + break; + case UNINITIALIZED: + default: + { + snprintf(errbuf, sizeof(errbuf), + "Undefined symbol %s referenced", + symbol->name); + stop(errbuf, EX_DATAERR); + /* NOTREACHED */ + break; + } + } + SLIST_INIT(&$$.referenced_syms); + symlist_add(&$$.referenced_syms, symbol, SYMLIST_INSERT_HEAD); + } +; + +constant: + T_CONST T_SYMBOL expression + { + if ($2->type != UNINITIALIZED) { + stop("Re-definition of symbol as a constant", + EX_DATAERR); + /* NOTREACHED */ + } + $2->type = CONST; + initialize_symbol($2); + $2->info.cinfo->value = $3.value; + } +| T_CONST T_SYMBOL T_DOWNLOAD + { + if ($1) { + stop("Invalid downloaded constant declaration", + EX_DATAERR); + /* NOTREACHED */ + } + if ($2->type != UNINITIALIZED) { + stop("Re-definition of symbol as a downloaded constant", + EX_DATAERR); + /* NOTREACHED */ + } + $2->type = DOWNLOAD_CONST; + initialize_symbol($2); + $2->info.cinfo->value = download_constant_count++; + } +; + +macrodefn_prologue: + T_DEFINE T_SYMBOL + { + if ($2->type != UNINITIALIZED) { + stop("Re-definition of symbol as a macro", + EX_DATAERR); + /* NOTREACHED */ + } + cur_symbol = $2; + cur_symbol->type = MACRO; + initialize_symbol(cur_symbol); + } +; + +macrodefn: + macrodefn_prologue T_MACROBODY + { + add_macro_body($2); + } +| macrodefn_prologue '(' macro_arglist ')' T_MACROBODY + { + add_macro_body($5); + cur_symbol->info.macroinfo->narg = $3; + } +; + +macro_arglist: + { + /* Macros can take no arguments */ + $$ = 0; + } +| T_ARG + { + $$ = 1; + add_macro_arg($1, 0); + } +| macro_arglist ',' T_ARG + { + if ($1 == 0) { + stop("Comma without preceding argument in arg list", + EX_DATAERR); + /* NOTREACHED */ + } + $$ = $1 + 1; + add_macro_arg($3, $1); + } +; + +scratch_ram: + T_SRAM '{' + { + snprintf(errbuf, sizeof(errbuf), "%s%d", SRAM_SYMNAME, + num_srams); + cur_symbol = symtable_get(SRAM_SYMNAME); + cur_symtype = SRAMLOC; + cur_symbol->type = SRAMLOC; + initialize_symbol(cur_symbol); + cur_symbol->count += 1; + } + reg_address + { + sram_or_scb_offset = cur_symbol->info.rinfo->address; + } + size + { + scb_or_sram_symbol = cur_symbol; + } + scb_or_sram_attributes + '}' + { + cur_symbol = NULL; + scb_or_sram_symbol = NULL; + } +; + +scb: + T_SCB '{' + { + cur_symbol = symtable_get(SCB_SYMNAME); + cur_symtype = SCBLOC; + if (cur_symbol->type != UNINITIALIZED) { + stop("Only one SRAM definition allowed", + EX_SOFTWARE); + /* NOTREACHED */ + } + cur_symbol->type = SCBLOC; + initialize_symbol(cur_symbol); + /* 64 bytes of SCB space */ + cur_symbol->info.rinfo->size = 64; + cur_symbol->count += 1; + } + reg_address + { + sram_or_scb_offset = cur_symbol->info.rinfo->address; + } + size + { + scb_or_sram_symbol = cur_symbol; + } + scb_or_sram_attributes + '}' + { + cur_symbol = NULL; + scb_or_sram_symbol = NULL; + } +; + +scb_or_sram_attributes: + /* NULL definition is okay */ +| modes +| scb_or_sram_reg_list +| modes scb_or_sram_reg_list +; + +scb_or_sram_reg_list: + reg_definition +| scb_or_sram_reg_list reg_definition +; + +reg_symbol: + T_SYMBOL + { + process_register(&$1); + $$.symbol = $1; + $$.offset = 0; + } +| T_SYMBOL '[' T_SYMBOL ']' + { + process_register(&$1); + if ($3->type != CONST) { + stop("register offset must be a constant", EX_DATAERR); + /* NOTREACHED */ + } + if (($3->info.cinfo->value + 1) > $1->info.rinfo->size) { + stop("Accessing offset beyond range of register", + EX_DATAERR); + /* NOTREACHED */ + } + $$.symbol = $1; + $$.offset = $3->info.cinfo->value; + } +| T_SYMBOL '[' T_NUMBER ']' + { + process_register(&$1); + if (($3 + 1) > $1->info.rinfo->size) { + stop("Accessing offset beyond range of register", + EX_DATAERR); + /* NOTREACHED */ + } + $$.symbol = $1; + $$.offset = $3; + } +| T_A + { + if (accumulator.symbol == NULL) { + stop("No accumulator has been defined", EX_DATAERR); + /* NOTREACHED */ + } + $$.symbol = accumulator.symbol; + $$.offset = 0; + } +; + +destination: + reg_symbol + { + test_writable_symbol($1.symbol); + $$ = $1; + } +; + +immediate: + expression + { $$ = $1; } +; + +immediate_or_a: + expression + { + if ($1.value == 0 && is_download_const(&$1) == 0) { + snprintf(errbuf, sizeof(errbuf), + "\nExpression evaluates to 0 and thus " + "references the accumulator.\n " + "If this is the desired effect, use 'A' " + "instead.\n"); + stop(errbuf, EX_DATAERR); + } + $$ = $1; + } +| T_A + { + SLIST_INIT(&$$.referenced_syms); + symlist_add(&$$.referenced_syms, accumulator.symbol, + SYMLIST_INSERT_HEAD); + $$.value = 0; + } +; + +source: + reg_symbol + { + test_readable_symbol($1.symbol); + $$ = $1; + } +; + +opt_source: + { + $$.symbol = NULL; + $$.offset = 0; + } +| ',' source + { $$ = $2; } +; + +ret: + { $$ = 0; } +| T_RET + { $$ = 1; } +; + +set_src_mode: + T_SET_SRC_MODE T_NUMBER ';' + { + src_mode = $2; + } +; + +set_dst_mode: + T_SET_DST_MODE T_NUMBER ';' + { + dst_mode = $2; + } +; + +critical_section_start: + T_BEGIN_CS ';' + { + critical_section_t *cs; + + if (in_critical_section != FALSE) { + stop("Critical Section within Critical Section", + EX_DATAERR); + /* NOTREACHED */ + } + cs = cs_alloc(); + cs->begin_addr = instruction_ptr; + in_critical_section = TRUE; + } +; + +critical_section_end: + T_END_CS ';' + { + critical_section_t *cs; + + if (in_critical_section == FALSE) { + stop("Unballanced 'end_cs'", EX_DATAERR); + /* NOTREACHED */ + } + cs = TAILQ_LAST(&cs_tailq, cs_tailq); + cs->end_addr = instruction_ptr; + in_critical_section = FALSE; + } +; + +export: + { $$ = 0; } +| T_EXPORT + { $$ = 1; } +; + +label: + export T_SYMBOL ':' + { + if ($2->type != UNINITIALIZED) { + stop("Program label multiply defined", EX_DATAERR); + /* NOTREACHED */ + } + $2->type = LABEL; + initialize_symbol($2); + $2->info.linfo->address = instruction_ptr; + $2->info.linfo->exported = $1; + } +; + +address: + T_SYMBOL + { + $$.symbol = $1; + $$.offset = 0; + } +| T_SYMBOL '+' T_NUMBER + { + $$.symbol = $1; + $$.offset = $3; + } +| T_SYMBOL '-' T_NUMBER + { + $$.symbol = $1; + $$.offset = -$3; + } +| '.' + { + $$.symbol = NULL; + $$.offset = 0; + } +| '.' '+' T_NUMBER + { + $$.symbol = NULL; + $$.offset = $3; + } +| '.' '-' T_NUMBER + { + $$.symbol = NULL; + $$.offset = -$3; + } +; + +conditional: + T_IF T_CEXPR '{' + { + scope_t *new_scope; + + add_conditional($2); + new_scope = scope_alloc(); + new_scope->type = SCOPE_IF; + new_scope->begin_addr = instruction_ptr; + new_scope->func_num = $2->info.condinfo->func_num; + } +| T_ELSE T_IF T_CEXPR '{' + { + scope_t *new_scope; + scope_t *scope_context; + scope_t *last_scope; + + /* + * Ensure that the previous scope is either an + * if or and else if. + */ + scope_context = SLIST_FIRST(&scope_stack); + last_scope = TAILQ_LAST(&scope_context->inner_scope, + scope_tailq); + if (last_scope == NULL + || last_scope->type == T_ELSE) { + + stop("'else if' without leading 'if'", EX_DATAERR); + /* NOTREACHED */ + } + add_conditional($3); + new_scope = scope_alloc(); + new_scope->type = SCOPE_ELSE_IF; + new_scope->begin_addr = instruction_ptr; + new_scope->func_num = $3->info.condinfo->func_num; + } +| T_ELSE '{' + { + scope_t *new_scope; + scope_t *scope_context; + scope_t *last_scope; + + /* + * Ensure that the previous scope is either an + * if or and else if. + */ + scope_context = SLIST_FIRST(&scope_stack); + last_scope = TAILQ_LAST(&scope_context->inner_scope, + scope_tailq); + if (last_scope == NULL + || last_scope->type == SCOPE_ELSE) { + + stop("'else' without leading 'if'", EX_DATAERR); + /* NOTREACHED */ + } + new_scope = scope_alloc(); + new_scope->type = SCOPE_ELSE; + new_scope->begin_addr = instruction_ptr; + } +; + +conditional: + '}' + { + scope_t *scope_context; + + scope_context = SLIST_FIRST(&scope_stack); + if (scope_context->type == SCOPE_ROOT) { + stop("Unexpected '}' encountered", EX_DATAERR); + /* NOTREACHED */ + } + + scope_context->end_addr = instruction_ptr; + + /* Pop the scope */ + SLIST_REMOVE_HEAD(&scope_stack, scope_stack_links); + + process_scope(scope_context); + + if (SLIST_FIRST(&scope_stack) == NULL) { + stop("Unexpected '}' encountered", EX_DATAERR); + /* NOTREACHED */ + } + } +; + +f1_opcode: + T_AND { $$ = AIC_OP_AND; } +| T_XOR { $$ = AIC_OP_XOR; } +| T_ADD { $$ = AIC_OP_ADD; } +| T_ADC { $$ = AIC_OP_ADC; } +; + +code: + f1_opcode destination ',' immediate_or_a opt_source ret ';' + { + format_1_instr($1, &$2, &$4, &$5, $6); + } +; + +code: + T_OR reg_symbol ',' immediate_or_a opt_source ret ';' + { + format_1_instr(AIC_OP_OR, &$2, &$4, &$5, $6); + } +; + +code: + T_INC destination opt_source ret ';' + { + expression_t immed; + + make_expression(&immed, 1); + format_1_instr(AIC_OP_ADD, &$2, &immed, &$3, $4); + } +; + +code: + T_DEC destination opt_source ret ';' + { + expression_t immed; + + make_expression(&immed, -1); + format_1_instr(AIC_OP_ADD, &$2, &immed, &$3, $4); + } +; + +code: + T_CLC ret ';' + { + expression_t immed; + + make_expression(&immed, -1); + format_1_instr(AIC_OP_ADD, &none, &immed, &allzeros, $2); + } +| T_CLC T_MVI destination ',' immediate_or_a ret ';' + { + format_1_instr(AIC_OP_ADD, &$3, &$5, &allzeros, $6); + } +; + +code: + T_STC ret ';' + { + expression_t immed; + + make_expression(&immed, 1); + format_1_instr(AIC_OP_ADD, &none, &immed, &allones, $2); + } +| T_STC destination ret ';' + { + expression_t immed; + + make_expression(&immed, 1); + format_1_instr(AIC_OP_ADD, &$2, &immed, &allones, $3); + } +; + +code: + T_BMOV destination ',' source ',' immediate ret ';' + { + format_1_instr(AIC_OP_BMOV, &$2, &$6, &$4, $7); + } +; + +code: + T_MOV destination ',' source ret ';' + { + expression_t immed; + + make_expression(&immed, 1); + format_1_instr(AIC_OP_BMOV, &$2, &immed, &$4, $5); + } +; + +code: + T_MVI destination ',' immediate ret ';' + { + if ($4.value == 0 + && is_download_const(&$4) == 0) { + expression_t immed; + + /* + * Allow move immediates of 0 so that macros, + * that can't know the immediate's value and + * otherwise compensate, still work. + */ + make_expression(&immed, 1); + format_1_instr(AIC_OP_BMOV, &$2, &immed, &allzeros, $5); + } else { + format_1_instr(AIC_OP_OR, &$2, &$4, &allzeros, $5); + } + } +; + +code: + T_NOT destination opt_source ret ';' + { + expression_t immed; + + make_expression(&immed, 0xff); + format_1_instr(AIC_OP_XOR, &$2, &immed, &$3, $4); + } +; + +code: + T_CLR destination ret ';' + { + expression_t immed; + + make_expression(&immed, 0xff); + format_1_instr(AIC_OP_AND, &$2, &immed, &allzeros, $3); + } +; + +code: + T_NOP ret ';' + { + expression_t immed; + + make_expression(&immed, 0xff); + format_1_instr(AIC_OP_AND, &none, &immed, &allzeros, $2); + } +; + +code: + T_RET ';' + { + expression_t immed; + + make_expression(&immed, 0xff); + format_1_instr(AIC_OP_AND, &none, &immed, &allzeros, TRUE); + } +; + + /* + * This grammar differs from the one in the aic7xxx + * reference manual since the grammar listed there is + * ambiguous and causes a shift/reduce conflict. + * It also seems more logical as the "immediate" + * argument is listed as the second arg like the + * other formats. + */ + +f2_opcode: + T_SHL { $$ = AIC_OP_SHL; } +| T_SHR { $$ = AIC_OP_SHR; } +| T_ROL { $$ = AIC_OP_ROL; } +| T_ROR { $$ = AIC_OP_ROR; } +; + +/* + * 16bit opcodes, not used + * + *f4_opcode: + * T_OR16 { $$ = AIC_OP_OR16; } + *| T_AND16 { $$ = AIC_OP_AND16; } + *| T_XOR16 { $$ = AIC_OP_XOR16; } + *| T_ADD16 { $$ = AIC_OP_ADD16; } + *| T_ADC16 { $$ = AIC_OP_ADC16; } + *| T_MVI16 { $$ = AIC_OP_MVI16; } + *; + */ + +code: + f2_opcode destination ',' expression opt_source ret ';' + { + format_2_instr($1, &$2, &$4, &$5, $6); + } +; + +jmp_jc_jnc_call: + T_JMP { $$ = AIC_OP_JMP; } +| T_JC { $$ = AIC_OP_JC; } +| T_JNC { $$ = AIC_OP_JNC; } +| T_CALL { $$ = AIC_OP_CALL; } +; + +jz_jnz: + T_JZ { $$ = AIC_OP_JZ; } +| T_JNZ { $$ = AIC_OP_JNZ; } +; + +je_jne: + T_JE { $$ = AIC_OP_JE; } +| T_JNE { $$ = AIC_OP_JNE; } +; + +code: + jmp_jc_jnc_call address ';' + { + expression_t immed; + + make_expression(&immed, 0); + format_3_instr($1, &sindex, &immed, &$2); + } +; + +code: + T_OR reg_symbol ',' immediate jmp_jc_jnc_call address ';' + { + type_check(&$2, &$4, AIC_OP_OR); + format_3_instr($5, &$2, &$4, &$6); + } +; + +code: + T_TEST source ',' immediate_or_a jz_jnz address ';' + { + format_3_instr($5, &$2, &$4, &$6); + } +; + +code: + T_CMP source ',' immediate_or_a je_jne address ';' + { + format_3_instr($5, &$2, &$4, &$6); + } +; + +code: + T_MOV source jmp_jc_jnc_call address ';' + { + expression_t immed; + + make_expression(&immed, 0); + format_3_instr($3, &$2, &immed, &$4); + } +; + +code: + T_MVI immediate jmp_jc_jnc_call address ';' + { + format_3_instr($3, &allzeros, &$2, &$4); + } +; + +%% + +static void +process_field(int field_type, symbol_t *sym, int value) +{ + /* + * Add the current register to its + * symbol list, if it already exists, + * warn if we are setting it to a + * different value, or in the bit to + * the "allowed bits" of this register. + */ + if (sym->type == UNINITIALIZED) { + sym->type = field_type; + initialize_symbol(sym); + sym->info.finfo->value = value; + if (field_type != ENUM_ENTRY) { + if (field_type != MASK && value == 0) { + stop("Empty Field, or Enum", EX_DATAERR); + /* NOTREACHED */ + } + sym->info.finfo->value = value; + sym->info.finfo->mask = value; + } else if (field_symbol != NULL) { + sym->info.finfo->mask = field_symbol->info.finfo->value; + } else { + sym->info.finfo->mask = 0xFF; + } + } else if (sym->type != field_type) { + stop("Field definition mirrors a definition of the same " + " name, but a different type", EX_DATAERR); + /* NOTREACHED */ + } else if (value != sym->info.finfo->value) { + stop("Field redefined with a conflicting value", EX_DATAERR); + /* NOTREACHED */ + } + /* Fail if this symbol is already listed */ + if (symlist_search(&(sym->info.finfo->symrefs), + cur_symbol->name) != NULL) { + stop("Field defined multiple times for register", EX_DATAERR); + /* NOTREACHED */ + } + symlist_add(&(sym->info.finfo->symrefs), cur_symbol, + SYMLIST_INSERT_HEAD); + cur_symbol->info.rinfo->valid_bitmask |= sym->info.finfo->mask; + cur_symbol->info.rinfo->typecheck_masks = TRUE; + symlist_add(&(cur_symbol->info.rinfo->fields), sym, SYMLIST_SORT); +} + +static void +initialize_symbol(symbol_t *symbol) +{ + switch (symbol->type) { + case UNINITIALIZED: + stop("Call to initialize_symbol with type field unset", + EX_SOFTWARE); + /* NOTREACHED */ + break; + case REGISTER: + case SRAMLOC: + case SCBLOC: + symbol->info.rinfo = + (struct reg_info *)malloc(sizeof(struct reg_info)); + if (symbol->info.rinfo == NULL) { + stop("Can't create register info", EX_SOFTWARE); + /* NOTREACHED */ + } + memset(symbol->info.rinfo, 0, + sizeof(struct reg_info)); + SLIST_INIT(&(symbol->info.rinfo->fields)); + /* + * Default to allowing access in all register modes + * or to the mode specified by the SCB or SRAM space + * we are in. + */ + if (scb_or_sram_symbol != NULL) + symbol->info.rinfo->modes = + scb_or_sram_symbol->info.rinfo->modes; + else + symbol->info.rinfo->modes = ~0; + break; + case ALIAS: + symbol->info.ainfo = + (struct alias_info *)malloc(sizeof(struct alias_info)); + if (symbol->info.ainfo == NULL) { + stop("Can't create alias info", EX_SOFTWARE); + /* NOTREACHED */ + } + memset(symbol->info.ainfo, 0, + sizeof(struct alias_info)); + break; + case MASK: + case FIELD: + case ENUM: + case ENUM_ENTRY: + symbol->info.finfo = + (struct field_info *)malloc(sizeof(struct field_info)); + if (symbol->info.finfo == NULL) { + stop("Can't create field info", EX_SOFTWARE); + /* NOTREACHED */ + } + memset(symbol->info.finfo, 0, sizeof(struct field_info)); + SLIST_INIT(&(symbol->info.finfo->symrefs)); + break; + case CONST: + case DOWNLOAD_CONST: + symbol->info.cinfo = + (struct const_info *)malloc(sizeof(struct const_info)); + if (symbol->info.cinfo == NULL) { + stop("Can't create alias info", EX_SOFTWARE); + /* NOTREACHED */ + } + memset(symbol->info.cinfo, 0, + sizeof(struct const_info)); + break; + case LABEL: + symbol->info.linfo = + (struct label_info *)malloc(sizeof(struct label_info)); + if (symbol->info.linfo == NULL) { + stop("Can't create label info", EX_SOFTWARE); + /* NOTREACHED */ + } + memset(symbol->info.linfo, 0, + sizeof(struct label_info)); + break; + case CONDITIONAL: + symbol->info.condinfo = + (struct cond_info *)malloc(sizeof(struct cond_info)); + if (symbol->info.condinfo == NULL) { + stop("Can't create conditional info", EX_SOFTWARE); + /* NOTREACHED */ + } + memset(symbol->info.condinfo, 0, + sizeof(struct cond_info)); + break; + case MACRO: + symbol->info.macroinfo = + (struct macro_info *)malloc(sizeof(struct macro_info)); + if (symbol->info.macroinfo == NULL) { + stop("Can't create macro info", EX_SOFTWARE); + /* NOTREACHED */ + } + memset(symbol->info.macroinfo, 0, + sizeof(struct macro_info)); + STAILQ_INIT(&symbol->info.macroinfo->args); + break; + default: + stop("Call to initialize_symbol with invalid symbol type", + EX_SOFTWARE); + /* NOTREACHED */ + break; + } +} + +static void +add_macro_arg(const char *argtext, int argnum) +{ + struct macro_arg *marg; + int i; + int retval; + + if (cur_symbol == NULL || cur_symbol->type != MACRO) { + stop("Invalid current symbol for adding macro arg", + EX_SOFTWARE); + /* NOTREACHED */ + } + + marg = (struct macro_arg *)malloc(sizeof(*marg)); + if (marg == NULL) { + stop("Can't create macro_arg structure", EX_SOFTWARE); + /* NOTREACHED */ + } + marg->replacement_text = NULL; + retval = snprintf(regex_pattern, sizeof(regex_pattern), + "[^-/A-Za-z0-9_](%s)([^-/A-Za-z0-9_]|$)", + argtext); + if (retval >= sizeof(regex_pattern)) { + stop("Regex text buffer too small for arg", + EX_SOFTWARE); + /* NOTREACHED */ + } + retval = regcomp(&marg->arg_regex, regex_pattern, REG_EXTENDED); + if (retval != 0) { + stop("Regex compilation failed", EX_SOFTWARE); + /* NOTREACHED */ + } + STAILQ_INSERT_TAIL(&cur_symbol->info.macroinfo->args, marg, links); +} + +static void +add_macro_body(const char *bodytext) +{ + if (cur_symbol == NULL || cur_symbol->type != MACRO) { + stop("Invalid current symbol for adding macro arg", + EX_SOFTWARE); + /* NOTREACHED */ + } + cur_symbol->info.macroinfo->body = strdup(bodytext); + if (cur_symbol->info.macroinfo->body == NULL) { + stop("Can't duplicate macro body text", EX_SOFTWARE); + /* NOTREACHED */ + } +} + +static void +process_register(symbol_t **p_symbol) +{ + symbol_t *symbol = *p_symbol; + + if (symbol->type == UNINITIALIZED) { + snprintf(errbuf, sizeof(errbuf), "Undefined register %s", + symbol->name); + stop(errbuf, EX_DATAERR); + /* NOTREACHED */ + } else if (symbol->type == ALIAS) { + *p_symbol = symbol->info.ainfo->parent; + } else if ((symbol->type != REGISTER) + && (symbol->type != SCBLOC) + && (symbol->type != SRAMLOC)) { + snprintf(errbuf, sizeof(errbuf), + "Specified symbol %s is not a register", + symbol->name); + stop(errbuf, EX_DATAERR); + } +} + +static void +format_1_instr(int opcode, symbol_ref_t *dest, expression_t *immed, + symbol_ref_t *src, int ret) +{ + struct instruction *instr; + struct ins_format1 *f1_instr; + + if (src->symbol == NULL) + src = dest; + + /* Test register permissions */ + test_writable_symbol(dest->symbol); + test_readable_symbol(src->symbol); + + if (!is_location_address(dest->symbol)) { + /* Ensure that immediate makes sense for this destination */ + type_check(dest, immed, opcode); + } + + /* Allocate sequencer space for the instruction and fill it out */ + instr = seq_alloc(); + f1_instr = &instr->format.format1; + f1_instr->ret = ret ? 1 : 0; + f1_instr->opcode = opcode; + f1_instr->destination = dest->symbol->info.rinfo->address + + dest->offset; + f1_instr->source = src->symbol->info.rinfo->address + + src->offset; + f1_instr->immediate = immed->value; + + if (is_download_const(immed)) + f1_instr->parity = 1; + else if (dest->symbol == mode_ptr.symbol) { + u_int src_value; + u_int dst_value; + + /* + * Attempt to update mode information if + * we are operating on the mode register. + */ + if (src->symbol == allones.symbol) + src_value = 0xFF; + else if (src->symbol == allzeros.symbol) + src_value = 0; + else if (src->symbol == mode_ptr.symbol) + src_value = (dst_mode << 4) | src_mode; + else + goto cant_update; + + switch (opcode) { + case AIC_OP_AND: + dst_value = src_value & immed->value; + break; + case AIC_OP_XOR: + dst_value = src_value ^ immed->value; + break; + case AIC_OP_ADD: + dst_value = (src_value + immed->value) & 0xFF; + break; + case AIC_OP_OR: + dst_value = src_value | immed->value; + break; + case AIC_OP_BMOV: + dst_value = src_value; + break; + default: + goto cant_update; + } + src_mode = dst_value & 0xF; + dst_mode = (dst_value >> 4) & 0xF; + } + +cant_update: + symlist_free(&immed->referenced_syms); + instruction_ptr++; +} + +static void +format_2_instr(int opcode, symbol_ref_t *dest, expression_t *places, + symbol_ref_t *src, int ret) +{ + struct instruction *instr; + struct ins_format2 *f2_instr; + uint8_t shift_control; + + if (src->symbol == NULL) + src = dest; + + /* Test register permissions */ + test_writable_symbol(dest->symbol); + test_readable_symbol(src->symbol); + + /* Allocate sequencer space for the instruction and fill it out */ + instr = seq_alloc(); + f2_instr = &instr->format.format2; + f2_instr->ret = ret ? 1 : 0; + f2_instr->opcode = AIC_OP_ROL; + f2_instr->destination = dest->symbol->info.rinfo->address + + dest->offset; + f2_instr->source = src->symbol->info.rinfo->address + + src->offset; + if (places->value > 8 || places->value <= 0) { + stop("illegal shift value", EX_DATAERR); + /* NOTREACHED */ + } + switch (opcode) { + case AIC_OP_SHL: + if (places->value == 8) + shift_control = 0xf0; + else + shift_control = (places->value << 4) | places->value; + break; + case AIC_OP_SHR: + if (places->value == 8) { + shift_control = 0xf8; + } else { + shift_control = (places->value << 4) + | (8 - places->value) + | 0x08; + } + break; + case AIC_OP_ROL: + shift_control = places->value & 0x7; + break; + case AIC_OP_ROR: + shift_control = (8 - places->value) | 0x08; + break; + default: + shift_control = 0; /* Quiet Compiler */ + stop("Invalid shift operation specified", EX_SOFTWARE); + /* NOTREACHED */ + break; + }; + f2_instr->shift_control = shift_control; + symlist_free(&places->referenced_syms); + instruction_ptr++; +} + +static void +format_3_instr(int opcode, symbol_ref_t *src, + expression_t *immed, symbol_ref_t *address) +{ + struct instruction *instr; + struct ins_format3 *f3_instr; + int addr; + + /* Test register permissions */ + test_readable_symbol(src->symbol); + + /* Allocate sequencer space for the instruction and fill it out */ + instr = seq_alloc(); + f3_instr = &instr->format.format3; + if (address->symbol == NULL) { + /* 'dot' reference. Use the current instruction pointer */ + addr = instruction_ptr + address->offset; + } else if (address->symbol->type == UNINITIALIZED) { + /* forward reference */ + addr = address->offset; + instr->patch_label = address->symbol; + } else + addr = address->symbol->info.linfo->address + address->offset; + f3_instr->opcode = opcode; + f3_instr->address = addr; + f3_instr->source = src->symbol->info.rinfo->address + + src->offset; + f3_instr->immediate = immed->value; + + if (is_download_const(immed)) + f3_instr->parity = 1; + + symlist_free(&immed->referenced_syms); + instruction_ptr++; +} + +static void +test_readable_symbol(symbol_t *symbol) +{ + if ((symbol->info.rinfo->modes & (0x1 << src_mode)) == 0) { + snprintf(errbuf, sizeof(errbuf), + "Register %s unavailable in source reg mode %d", + symbol->name, src_mode); + stop(errbuf, EX_DATAERR); + } + + if (symbol->info.rinfo->mode == WO) { + stop("Write Only register specified as source", + EX_DATAERR); + /* NOTREACHED */ + } +} + +static void +test_writable_symbol(symbol_t *symbol) +{ + if ((symbol->info.rinfo->modes & (0x1 << dst_mode)) == 0) { + snprintf(errbuf, sizeof(errbuf), + "Register %s unavailable in destination reg mode %d", + symbol->name, dst_mode); + stop(errbuf, EX_DATAERR); + } + + if (symbol->info.rinfo->mode == RO) { + stop("Read Only register specified as destination", + EX_DATAERR); + /* NOTREACHED */ + } +} + +static void +type_check(symbol_ref_t *sym, expression_t *expression, int opcode) +{ + symbol_t *symbol = sym->symbol; + symbol_node_t *node; + int and_op; + int8_t value, mask; + + and_op = FALSE; + /* + * Make sure that we aren't attempting to write something + * that hasn't been defined. If this is an and operation, + * this is a mask, so "undefined" bits are okay. + */ + if (opcode == AIC_OP_AND || opcode == AIC_OP_JNZ || + opcode == AIC_OP_JZ || opcode == AIC_OP_JNE || + opcode == AIC_OP_BMOV) + and_op = TRUE; + + /* + * Defaulting to 8 bit logic + */ + mask = (int8_t)~symbol->info.rinfo->valid_bitmask; + value = (int8_t)expression->value; + + if (and_op == FALSE && (mask & value) != 0 ) { + snprintf(errbuf, sizeof(errbuf), + "Invalid bit(s) 0x%x in immediate written to %s", + (mask & value), + symbol->name); + stop(errbuf, EX_DATAERR); + /* NOTREACHED */ + } + + /* + * Now make sure that all of the symbols referenced by the + * expression are defined for this register. + */ + if (symbol->info.rinfo->typecheck_masks != FALSE) { + for(node = expression->referenced_syms.slh_first; + node != NULL; + node = node->links.sle_next) { + if ((node->symbol->type == MASK + || node->symbol->type == FIELD + || node->symbol->type == ENUM + || node->symbol->type == ENUM_ENTRY) + && symlist_search(&node->symbol->info.finfo->symrefs, + symbol->name) == NULL) { + snprintf(errbuf, sizeof(errbuf), + "Invalid field or mask %s " + "for register %s", + node->symbol->name, symbol->name); + stop(errbuf, EX_DATAERR); + /* NOTREACHED */ + } + } + } +} + +static void +make_expression(expression_t *immed, int value) +{ + SLIST_INIT(&immed->referenced_syms); + immed->value = value & 0xff; +} + +static void +add_conditional(symbol_t *symbol) +{ + static int numfuncs; + + if (numfuncs == 0) { + /* add a special conditional, "0" */ + symbol_t *false_func; + + false_func = symtable_get("0"); + if (false_func->type != UNINITIALIZED) { + stop("Conditional expression '0' " + "conflicts with a symbol", EX_DATAERR); + /* NOTREACHED */ + } + false_func->type = CONDITIONAL; + initialize_symbol(false_func); + false_func->info.condinfo->func_num = numfuncs++; + symlist_add(&patch_functions, false_func, SYMLIST_INSERT_HEAD); + } + + /* This condition has occurred before */ + if (symbol->type == CONDITIONAL) + return; + + if (symbol->type != UNINITIALIZED) { + stop("Conditional expression conflicts with a symbol", + EX_DATAERR); + /* NOTREACHED */ + } + + symbol->type = CONDITIONAL; + initialize_symbol(symbol); + symbol->info.condinfo->func_num = numfuncs++; + symlist_add(&patch_functions, symbol, SYMLIST_INSERT_HEAD); +} + +static void +add_version(const char *verstring) +{ + const char prefix[] = " * "; + int newlen; + int oldlen; + + newlen = strlen(verstring) + strlen(prefix); + oldlen = 0; + if (versions != NULL) + oldlen = strlen(versions); + versions = realloc(versions, newlen + oldlen + 2); + if (versions == NULL) + stop("Can't allocate version string", EX_SOFTWARE); + strcpy(&versions[oldlen], prefix); + strcpy(&versions[oldlen + strlen(prefix)], verstring); + versions[newlen + oldlen] = '\n'; + versions[newlen + oldlen + 1] = '\0'; +} + +void +yyerror(const char *string) +{ + stop(string, EX_DATAERR); +} + +static int +is_download_const(expression_t *immed) +{ + if ((immed->referenced_syms.slh_first != NULL) + && (immed->referenced_syms.slh_first->symbol->type == DOWNLOAD_CONST)) + return (TRUE); + + return (FALSE); +} + +static int +is_location_address(symbol_t *sym) +{ + if (sym->type == SCBLOC || + sym->type == SRAMLOC) + return (TRUE); + return (FALSE); +} + diff --git a/drivers/scsi/aic7xxx/aicasm/aicasm_insformat.h b/drivers/scsi/aic7xxx/aicasm/aicasm_insformat.h new file mode 100644 index 000000000..8373447bd --- /dev/null +++ b/drivers/scsi/aic7xxx/aicasm/aicasm_insformat.h @@ -0,0 +1,218 @@ +/* + * Instruction formats for the sequencer program downloaded to + * Aic7xxx SCSI host adapters + * + * Copyright (c) 1997, 1998, 2000 Justin T. Gibbs. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aicasm/aicasm_insformat.h#12 $ + * + * $FreeBSD$ + */ + +#include <asm/byteorder.h> + +/* 8bit ALU logic operations */ +struct ins_format1 { +#ifdef __LITTLE_ENDIAN + uint32_t immediate : 8, + source : 9, + destination : 9, + ret : 1, + opcode : 4, + parity : 1; +#else + uint32_t parity : 1, + opcode : 4, + ret : 1, + destination : 9, + source : 9, + immediate : 8; +#endif +}; + +/* 8bit ALU shift/rotate operations */ +struct ins_format2 { +#ifdef __LITTLE_ENDIAN + uint32_t shift_control : 8, + source : 9, + destination : 9, + ret : 1, + opcode : 4, + parity : 1; +#else + uint32_t parity : 1, + opcode : 4, + ret : 1, + destination : 9, + source : 9, + shift_control : 8; +#endif +}; + +/* 8bit branch control operations */ +struct ins_format3 { +#ifdef __LITTLE_ENDIAN + uint32_t immediate : 8, + source : 9, + address : 10, + opcode : 4, + parity : 1; +#else + uint32_t parity : 1, + opcode : 4, + address : 10, + source : 9, + immediate : 8; +#endif +}; + +/* 16bit ALU logic operations */ +struct ins_format4 { +#ifdef __LITTLE_ENDIAN + uint32_t opcode_ext : 8, + source : 9, + destination : 9, + ret : 1, + opcode : 4, + parity : 1; +#else + uint32_t parity : 1, + opcode : 4, + ret : 1, + destination : 9, + source : 9, + opcode_ext : 8; +#endif +}; + +/* 16bit branch control operations */ +struct ins_format5 { +#ifdef __LITTLE_ENDIAN + uint32_t opcode_ext : 8, + source : 9, + address : 10, + opcode : 4, + parity : 1; +#else + uint32_t parity : 1, + opcode : 4, + address : 10, + source : 9, + opcode_ext : 8; +#endif +}; + +/* Far branch operations */ +struct ins_format6 { +#ifdef __LITTLE_ENDIAN + uint32_t page : 3, + opcode_ext : 5, + source : 9, + address : 10, + opcode : 4, + parity : 1; +#else + uint32_t parity : 1, + opcode : 4, + address : 10, + source : 9, + opcode_ext : 5, + page : 3; +#endif +}; + +union ins_formats { + struct ins_format1 format1; + struct ins_format2 format2; + struct ins_format3 format3; + struct ins_format4 format4; + struct ins_format5 format5; + struct ins_format6 format6; + uint8_t bytes[4]; + uint32_t integer; +}; +struct instruction { + union ins_formats format; + u_int srcline; + struct symbol *patch_label; + STAILQ_ENTRY(instruction) links; +}; + +#define AIC_OP_OR 0x0 +#define AIC_OP_AND 0x1 +#define AIC_OP_XOR 0x2 +#define AIC_OP_ADD 0x3 +#define AIC_OP_ADC 0x4 +#define AIC_OP_ROL 0x5 +#define AIC_OP_BMOV 0x6 + +#define AIC_OP_MVI16 0x7 + +#define AIC_OP_JMP 0x8 +#define AIC_OP_JC 0x9 +#define AIC_OP_JNC 0xa +#define AIC_OP_CALL 0xb +#define AIC_OP_JNE 0xc +#define AIC_OP_JNZ 0xd +#define AIC_OP_JE 0xe +#define AIC_OP_JZ 0xf + +/* Pseudo Ops */ +#define AIC_OP_SHL 0x10 +#define AIC_OP_SHR 0x20 +#define AIC_OP_ROR 0x30 + +/* 16bit Ops. Low byte main opcode. High byte extended opcode. */ +#define AIC_OP_OR16 0x8005 +#define AIC_OP_AND16 0x8105 +#define AIC_OP_XOR16 0x8205 +#define AIC_OP_ADD16 0x8305 +#define AIC_OP_ADC16 0x8405 +#define AIC_OP_JNE16 0x8805 +#define AIC_OP_JNZ16 0x8905 +#define AIC_OP_JE16 0x8C05 +#define AIC_OP_JZ16 0x8B05 +#define AIC_OP_JMP16 0x9005 +#define AIC_OP_JC16 0x9105 +#define AIC_OP_JNC16 0x9205 +#define AIC_OP_CALL16 0x9305 + +/* Page extension is low three bits of second opcode byte. */ +#define AIC_OP_JMPF 0xA005 +#define AIC_OP_CALLF 0xB005 +#define AIC_OP_JCF 0xC005 +#define AIC_OP_JNCF 0xD005 +#define AIC_OP_CMPXCHG 0xE005 diff --git a/drivers/scsi/aic7xxx/aicasm/aicasm_macro_gram.y b/drivers/scsi/aic7xxx/aicasm/aicasm_macro_gram.y new file mode 100644 index 000000000..8c0479865 --- /dev/null +++ b/drivers/scsi/aic7xxx/aicasm/aicasm_macro_gram.y @@ -0,0 +1,161 @@ +%{ +/* + * Sub-parser for macro invocation in the Aic7xxx SCSI + * Host adapter sequencer assembler. + * + * Copyright (c) 2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aicasm/aicasm_macro_gram.y#5 $ + * + * $FreeBSD$ + */ + +#include <sys/types.h> + +#include <inttypes.h> +#include <regex.h> +#include <stdio.h> +#include <stdlib.h> +#include <string.h> +#include <sysexits.h> + +#include "../queue.h" + +#include "aicasm.h" +#include "aicasm_symbol.h" +#include "aicasm_insformat.h" + +static symbol_t *macro_symbol; + +static void add_macro_arg(const char *argtext, int position); +void mmerror(const char *string); + +%} + +%union { + int value; + char *str; + symbol_t *sym; +} + + +%token <str> T_ARG + +%token <sym> T_SYMBOL + +%type <value> macro_arglist + +%% + +macrocall: + T_SYMBOL '(' + { + macro_symbol = $1; + } + macro_arglist ')' + { + if (macro_symbol->info.macroinfo->narg != $4) { + printf("Narg == %d", macro_symbol->info.macroinfo->narg); + stop("Too few arguments for macro invocation", + EX_DATAERR); + /* NOTREACHED */ + } + macro_symbol = NULL; + YYACCEPT; + } +; + +macro_arglist: + { + /* Macros can take 0 arguments */ + $$ = 0; + } +| T_ARG + { + $$ = 1; + add_macro_arg($1, 1); + } +| macro_arglist ',' T_ARG + { + if ($1 == 0) { + stop("Comma without preceding argument in arg list", + EX_DATAERR); + /* NOTREACHED */ + } + $$ = $1 + 1; + add_macro_arg($3, $$); + } +; + +%% + +static void +add_macro_arg(const char *argtext, int argnum) +{ + struct macro_arg *marg; + int i; + + if (macro_symbol == NULL || macro_symbol->type != MACRO) { + stop("Invalid current symbol for adding macro arg", + EX_SOFTWARE); + /* NOTREACHED */ + } + /* + * Macro Invocation. Find the appropriate argument and fill + * in the replace ment text for this call. + */ + i = 0; + STAILQ_FOREACH(marg, ¯o_symbol->info.macroinfo->args, links) { + i++; + if (i == argnum) + break; + } + if (marg == NULL) { + stop("Too many arguments for macro invocation", EX_DATAERR); + /* NOTREACHED */ + } + marg->replacement_text = strdup(argtext); + if (marg->replacement_text == NULL) { + stop("Unable to replicate replacement text", EX_SOFTWARE); + /* NOTREACHED */ + } +} + +void +mmerror(const char *string) +{ + stop(string, EX_DATAERR); +} diff --git a/drivers/scsi/aic7xxx/aicasm/aicasm_macro_scan.l b/drivers/scsi/aic7xxx/aicasm/aicasm_macro_scan.l new file mode 100644 index 000000000..98e9959c6 --- /dev/null +++ b/drivers/scsi/aic7xxx/aicasm/aicasm_macro_scan.l @@ -0,0 +1,153 @@ +%{ +/* + * Sub-Lexical Analyzer for macro invokation in + * the Aic7xxx SCSI Host adapter sequencer assembler. + * + * Copyright (c) 2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aicasm/aicasm_macro_scan.l#8 $ + * + * $FreeBSD$ + */ + +#include <sys/types.h> + +#include <inttypes.h> +#include <limits.h> +#include <regex.h> +#include <stdio.h> +#include <string.h> +#include <sysexits.h> +#include "../queue.h" + +#include "aicasm.h" +#include "aicasm_symbol.h" +#include "aicasm_macro_gram.h" + +#define MAX_STR_CONST 4096 +static char string_buf[MAX_STR_CONST]; +static char *string_buf_ptr; +static int parren_count; +static char buf[255]; +int mmlineno; +%} + +WORD [A-Za-z_][-A-Za-z_0-9]* +SPACE [ \t]+ +MCARG [^(), \t]+ + +%x ARGLIST + +%% +\n { + ++mmlineno; + } +\r ; +<ARGLIST>{SPACE} ; +<ARGLIST>\( { + parren_count++; + if (parren_count == 1) { + string_buf_ptr = string_buf; + return ('('); + } + *string_buf_ptr++ = '('; + } +<ARGLIST>\) { + if (parren_count == 1) { + if (string_buf_ptr != string_buf) { + /* + * Return an argument and + * rescan this parren so we + * can return it as well. + */ + *string_buf_ptr = '\0'; + mmlval.str = string_buf; + string_buf_ptr = string_buf; + unput(')'); + return T_ARG; + } + BEGIN INITIAL; + return (')'); + } + parren_count--; + *string_buf_ptr++ = ')'; + } +<ARGLIST>{MCARG} { + char *yptr; + + yptr = mmtext; + while (*yptr) + *string_buf_ptr++ = *yptr++; + } +<ARGLIST>\, { + if (string_buf_ptr != string_buf) { + /* + * Return an argument and + * rescan this comma so we + * can return it as well. + */ + *string_buf_ptr = '\0'; + mmlval.str = string_buf; + string_buf_ptr = string_buf; + unput(','); + return T_ARG; + } + return ','; + } +{WORD}[(] { + /* May be a symbol or a macro invocation. */ + mmlval.sym = symtable_get(mmtext); + if (mmlval.sym->type != MACRO) { + stop("Expecting Macro Name", + EX_DATAERR); + } + unput('('); + parren_count = 0; + BEGIN ARGLIST; + return T_SYMBOL; + } +. { + snprintf(buf, sizeof(buf), "Invalid character " + "'%c'", mmtext[0]); + stop(buf, EX_DATAERR); + } +%% + +int +mmwrap() +{ + stop("EOF encountered in macro call", EX_DATAERR); +} diff --git a/drivers/scsi/aic7xxx/aicasm/aicasm_scan.l b/drivers/scsi/aic7xxx/aicasm/aicasm_scan.l new file mode 100644 index 000000000..c78d4f68e --- /dev/null +++ b/drivers/scsi/aic7xxx/aicasm/aicasm_scan.l @@ -0,0 +1,618 @@ +%{ +/* + * Lexical Analyzer for the Aic7xxx SCSI Host adapter sequencer assembler. + * + * Copyright (c) 1997, 1998, 2000 Justin T. Gibbs. + * Copyright (c) 2001, 2002 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aicasm/aicasm_scan.l#20 $ + * + * $FreeBSD$ + */ + +#include <sys/types.h> + +#include <inttypes.h> +#include <limits.h> +#include <regex.h> +#include <stdio.h> +#include <string.h> +#include <sysexits.h> +#include "../queue.h" + +#include "aicasm.h" +#include "aicasm_symbol.h" +#include "aicasm_gram.h" + +/* This is used for macro body capture too, so err on the large size. */ +#define MAX_STR_CONST 4096 +static char string_buf[MAX_STR_CONST]; +static char *string_buf_ptr; +static int parren_count; +static int quote_count; +static char buf[255]; +%} + +PATH ([/]*[-A-Za-z0-9_.])+ +WORD [A-Za-z_][-A-Za-z_0-9]* +SPACE [ \t]+ +MCARG [^(), \t]+ +MBODY ((\\[^\n])*[^\n\\]*)+ + +%x COMMENT +%x CEXPR +%x INCLUDE +%x STRING +%x MACRODEF +%x MACROARGLIST +%x MACROCALLARGS +%x MACROBODY + +%% +\n { ++yylineno; } +\r ; +"/*" { BEGIN COMMENT; /* Enter comment eating state */ } +<COMMENT>"/*" { fprintf(stderr, "Warning! Comment within comment."); } +<COMMENT>\n { ++yylineno; } +<COMMENT>[^*/\n]* ; +<COMMENT>"*"+[^*/\n]* ; +<COMMENT>"/"+[^*/\n]* ; +<COMMENT>"*"+"/" { BEGIN INITIAL; } +if[ \t]*\( { + string_buf_ptr = string_buf; + parren_count = 1; + BEGIN CEXPR; + return T_IF; + } +<CEXPR>\( { *string_buf_ptr++ = '('; parren_count++; } +<CEXPR>\) { + parren_count--; + if (parren_count == 0) { + /* All done */ + BEGIN INITIAL; + *string_buf_ptr = '\0'; + yylval.sym = symtable_get(string_buf); + return T_CEXPR; + } else { + *string_buf_ptr++ = ')'; + } + } +<CEXPR>\n { ++yylineno; } +<CEXPR>\r ; +<CEXPR>[^()\n]+ { + char *yptr; + + yptr = yytext; + while (*yptr != '\0') { + /* Remove duplicate spaces */ + if (*yptr == '\t') + *yptr = ' '; + if (*yptr == ' ' + && string_buf_ptr != string_buf + && string_buf_ptr[-1] == ' ') + yptr++; + else + *string_buf_ptr++ = *yptr++; + } + } +else { return T_ELSE; } +VERSION { return T_VERSION; } +PREFIX { return T_PREFIX; } +PATCH_ARG_LIST { return T_PATCH_ARG_LIST; } +\" { + string_buf_ptr = string_buf; + BEGIN STRING; + } +<STRING>[^"]+ { + char *yptr; + + yptr = yytext; + while (*yptr) + *string_buf_ptr++ = *yptr++; + } +<STRING>\" { + /* All done */ + BEGIN INITIAL; + *string_buf_ptr = '\0'; + yylval.str = string_buf; + return T_STRING; + } +{SPACE} ; + + /* Register/SCB/SRAM definition keywords */ +export { return T_EXPORT; } +register { return T_REGISTER; } +const { yylval.value = FALSE; return T_CONST; } +download { return T_DOWNLOAD; } +address { return T_ADDRESS; } +count { return T_COUNT; } +access_mode { return T_ACCESS_MODE; } +dont_generate_debug_code { return T_DONT_GENERATE_DEBUG_CODE; } +modes { return T_MODES; } +RW|RO|WO { + if (strcmp(yytext, "RW") == 0) + yylval.value = RW; + else if (strcmp(yytext, "RO") == 0) + yylval.value = RO; + else + yylval.value = WO; + return T_MODE; + } +field { return T_FIELD; } +enum { return T_ENUM; } +mask { return T_MASK; } +alias { return T_ALIAS; } +size { return T_SIZE; } +scb { return T_SCB; } +scratch_ram { return T_SRAM; } +accumulator { return T_ACCUM; } +mode_pointer { return T_MODE_PTR; } +allones { return T_ALLONES; } +allzeros { return T_ALLZEROS; } +none { return T_NONE; } +sindex { return T_SINDEX; } +A { return T_A; } + + /* Instruction Formatting */ +PAD_PAGE { return T_PAD_PAGE; } +BEGIN_CRITICAL { return T_BEGIN_CS; } +END_CRITICAL { return T_END_CS; } +SET_SRC_MODE { return T_SET_SRC_MODE; } +SET_DST_MODE { return T_SET_DST_MODE; } + + /* Opcodes */ +shl { return T_SHL; } +shr { return T_SHR; } +ror { return T_ROR; } +rol { return T_ROL; } +mvi { return T_MVI; } +mov { return T_MOV; } +clr { return T_CLR; } +jmp { return T_JMP; } +jc { return T_JC; } +jnc { return T_JNC; } +je { return T_JE; } +jne { return T_JNE; } +jz { return T_JZ; } +jnz { return T_JNZ; } +call { return T_CALL; } +add { return T_ADD; } +adc { return T_ADC; } +bmov { return T_BMOV; } +inc { return T_INC; } +dec { return T_DEC; } +stc { return T_STC; } +clc { return T_CLC; } +cmp { return T_CMP; } +not { return T_NOT; } +xor { return T_XOR; } +test { return T_TEST;} +and { return T_AND; } +or { return T_OR; } +ret { return T_RET; } +nop { return T_NOP; } + + /* ARP2 16bit extensions */ + /* or16 { return T_OR16; } */ + /* and16 { return T_AND16; }*/ + /* xor16 { return T_XOR16; }*/ + /* add16 { return T_ADD16; }*/ + /* adc16 { return T_ADC16; }*/ + /* mvi16 { return T_MVI16; }*/ + /* test16 { return T_TEST16; }*/ + /* cmp16 { return T_CMP16; }*/ + /* cmpxchg { return T_CMPXCHG; }*/ + + /* Allowed Symbols */ +\<\< { return T_EXPR_LSHIFT; } +\>\> { return T_EXPR_RSHIFT; } +[-+,:()~|&."{};<>[\]/*!=] { return yytext[0]; } + + /* Number processing */ +0[0-7]* { + yylval.value = strtol(yytext, NULL, 8); + return T_NUMBER; + } + +0[xX][0-9a-fA-F]+ { + yylval.value = strtoul(yytext + 2, NULL, 16); + return T_NUMBER; + } + +[1-9][0-9]* { + yylval.value = strtol(yytext, NULL, 10); + return T_NUMBER; + } + /* Include Files */ +#include{SPACE} { + BEGIN INCLUDE; + quote_count = 0; + return T_INCLUDE; + } +<INCLUDE>[<] { return yytext[0]; } +<INCLUDE>[>] { BEGIN INITIAL; return yytext[0]; } +<INCLUDE>[\"] { + if (quote_count != 0) + BEGIN INITIAL; + quote_count++; + return yytext[0]; + } +<INCLUDE>{PATH} { + char *yptr; + + yptr = yytext; + string_buf_ptr = string_buf; + while (*yptr) + *string_buf_ptr++ = *yptr++; + yylval.str = string_buf; + *string_buf_ptr = '\0'; + return T_PATH; + } +<INCLUDE>. { stop("Invalid include line", EX_DATAERR); } +#define{SPACE} { + BEGIN MACRODEF; + return T_DEFINE; + } +<MACRODEF>{WORD}{SPACE} { + char *yptr; + + /* Strip space and return as a normal symbol */ + yptr = yytext; + while (*yptr != ' ' && *yptr != '\t') + yptr++; + *yptr = '\0'; + yylval.sym = symtable_get(yytext); + string_buf_ptr = string_buf; + BEGIN MACROBODY; + return T_SYMBOL; + } +<MACRODEF>{WORD}\( { + /* + * We store the symbol with its opening + * parren so we can differentiate macros + * that take args from macros with the + * same name that do not take args as + * is allowed in C. + */ + BEGIN MACROARGLIST; + yylval.sym = symtable_get(yytext); + unput('('); + return T_SYMBOL; + } +<MACROARGLIST>{WORD} { + yylval.str = yytext; + return T_ARG; + } +<MACROARGLIST>{SPACE} ; +<MACROARGLIST>[(,] { + return yytext[0]; + } +<MACROARGLIST>[)] { + string_buf_ptr = string_buf; + BEGIN MACROBODY; + return ')'; + } +<MACROARGLIST>. { + snprintf(buf, sizeof(buf), "Invalid character " + "'%c' in macro argument list", + yytext[0]); + stop(buf, EX_DATAERR); + } +<MACROCALLARGS>{SPACE} ; +<MACROCALLARGS>\( { + parren_count++; + if (parren_count == 1) + return ('('); + *string_buf_ptr++ = '('; + } +<MACROCALLARGS>\) { + parren_count--; + if (parren_count == 0) { + BEGIN INITIAL; + return (')'); + } + *string_buf_ptr++ = ')'; + } +<MACROCALLARGS>{MCARG} { + char *yptr; + + yptr = yytext; + while (*yptr) + *string_buf_ptr++ = *yptr++; + } +<MACROCALLARGS>\, { + if (string_buf_ptr != string_buf) { + /* + * Return an argument and + * rescan this comma so we + * can return it as well. + */ + *string_buf_ptr = '\0'; + yylval.str = string_buf; + string_buf_ptr = string_buf; + unput(','); + return T_ARG; + } + return ','; + } +<MACROBODY>\\\n { + /* Eat escaped newlines. */ + ++yylineno; + } +<MACROBODY>\r ; +<MACROBODY>\n { + /* Macros end on the first unescaped newline. */ + BEGIN INITIAL; + *string_buf_ptr = '\0'; + yylval.str = string_buf; + ++yylineno; + return T_MACROBODY; + } +<MACROBODY>{MBODY} { + char *yptr; + char c; + + yptr = yytext; + while (c = *yptr++) { + /* + * Strip carriage returns. + */ + if (c == '\r') + continue; + *string_buf_ptr++ = c; + } + } +{WORD}\( { + char *yptr; + char *ycopy; + + /* May be a symbol or a macro invocation. */ + yylval.sym = symtable_get(yytext); + if (yylval.sym->type == MACRO) { + YY_BUFFER_STATE old_state; + YY_BUFFER_STATE temp_state; + + ycopy = strdup(yytext); + yptr = ycopy + yyleng; + while (yptr > ycopy) + unput(*--yptr); + old_state = YY_CURRENT_BUFFER; + temp_state = + yy_create_buffer(stdin, + YY_BUF_SIZE); + yy_switch_to_buffer(temp_state); + mm_switch_to_buffer(old_state); + mmparse(); + mm_switch_to_buffer(temp_state); + yy_switch_to_buffer(old_state); + mm_delete_buffer(temp_state); + expand_macro(yylval.sym); + } else { + if (yylval.sym->type == UNINITIALIZED) { + /* Try without the '(' */ + symbol_delete(yylval.sym); + yytext[yyleng-1] = '\0'; + yylval.sym = + symtable_get(yytext); + } + unput('('); + return T_SYMBOL; + } + } +{WORD} { + yylval.sym = symtable_get(yytext); + if (yylval.sym->type == MACRO) { + expand_macro(yylval.sym); + } else { + return T_SYMBOL; + } + } +. { + snprintf(buf, sizeof(buf), "Invalid character " + "'%c'", yytext[0]); + stop(buf, EX_DATAERR); + } +%% + +typedef struct include { + YY_BUFFER_STATE buffer; + int lineno; + char *filename; + SLIST_ENTRY(include) links; +}include_t; + +SLIST_HEAD(, include) include_stack; + +void +include_file(char *file_name, include_type type) +{ + FILE *newfile; + include_t *include; + + newfile = NULL; + /* Try the current directory first */ + if (includes_search_curdir != 0 || type == SOURCE_FILE) + newfile = fopen(file_name, "r"); + + if (newfile == NULL && type != SOURCE_FILE) { + path_entry_t include_dir; + for (include_dir = search_path.slh_first; + include_dir != NULL; + include_dir = include_dir->links.sle_next) { + char fullname[PATH_MAX]; + + if ((include_dir->quoted_includes_only == TRUE) + && (type != QUOTED_INCLUDE)) + continue; + + snprintf(fullname, sizeof(fullname), + "%s/%s", include_dir->directory, file_name); + + if ((newfile = fopen(fullname, "r")) != NULL) + break; + } + } + + if (newfile == NULL) { + perror(file_name); + stop("Unable to open input file", EX_SOFTWARE); + /* NOTREACHED */ + } + + if (type != SOURCE_FILE) { + include = (include_t *)malloc(sizeof(include_t)); + if (include == NULL) { + stop("Unable to allocate include stack entry", + EX_SOFTWARE); + /* NOTREACHED */ + } + include->buffer = YY_CURRENT_BUFFER; + include->lineno = yylineno; + include->filename = yyfilename; + SLIST_INSERT_HEAD(&include_stack, include, links); + } + yy_switch_to_buffer(yy_create_buffer(newfile, YY_BUF_SIZE)); + yylineno = 1; + yyfilename = strdup(file_name); +} + +static void next_substitution(struct symbol *mac_symbol, const char *body_pos, + const char **next_match, + struct macro_arg **match_marg, regmatch_t *match); + +void +expand_macro(struct symbol *macro_symbol) +{ + struct macro_arg *marg; + struct macro_arg *match_marg; + const char *body_head; + const char *body_pos; + const char *next_match; + + /* + * Due to the nature of unput, we must work + * backwards through the macro body performing + * any expansions. + */ + body_head = macro_symbol->info.macroinfo->body; + body_pos = body_head + strlen(body_head); + while (body_pos > body_head) { + regmatch_t match; + + next_match = body_head; + match_marg = NULL; + next_substitution(macro_symbol, body_pos, &next_match, + &match_marg, &match); + + /* Put back everything up until the replacement. */ + while (body_pos > next_match) + unput(*--body_pos); + + /* Perform the replacement. */ + if (match_marg != NULL) { + const char *strp; + + next_match = match_marg->replacement_text; + strp = next_match + strlen(next_match); + while (strp > next_match) + unput(*--strp); + + /* Skip past the unexpanded macro arg. */ + body_pos -= match.rm_eo - match.rm_so; + } + } + + /* Cleanup replacement text. */ + STAILQ_FOREACH(marg, ¯o_symbol->info.macroinfo->args, links) { + free(marg->replacement_text); + } +} + +/* + * Find the next substitution in the macro working backwards from + * body_pos until the beginning of the macro buffer. next_match + * should be initialized to the beginning of the macro buffer prior + * to calling this routine. + */ +static void +next_substitution(struct symbol *mac_symbol, const char *body_pos, + const char **next_match, struct macro_arg **match_marg, + regmatch_t *match) +{ + regmatch_t matches[2]; + struct macro_arg *marg; + const char *search_pos; + int retval; + + do { + search_pos = *next_match; + + STAILQ_FOREACH(marg, &mac_symbol->info.macroinfo->args, links) { + + retval = regexec(&marg->arg_regex, search_pos, 2, + matches, 0); + if (retval == 0 + && (matches[1].rm_eo + search_pos) <= body_pos + && (matches[1].rm_eo + search_pos) > *next_match) { + *match = matches[1]; + *next_match = match->rm_eo + search_pos; + *match_marg = marg; + } + } + } while (search_pos != *next_match); +} + +int +yywrap() +{ + include_t *include; + + yy_delete_buffer(YY_CURRENT_BUFFER); + (void)fclose(yyin); + if (yyfilename != NULL) + free(yyfilename); + yyfilename = NULL; + include = include_stack.slh_first; + if (include != NULL) { + yy_switch_to_buffer(include->buffer); + yylineno = include->lineno; + yyfilename = include->filename; + SLIST_REMOVE_HEAD(&include_stack, links); + free(include); + return (0); + } + return (1); +} diff --git a/drivers/scsi/aic7xxx/aicasm/aicasm_symbol.c b/drivers/scsi/aic7xxx/aicasm/aicasm_symbol.c new file mode 100644 index 000000000..975fcfcc0 --- /dev/null +++ b/drivers/scsi/aic7xxx/aicasm/aicasm_symbol.c @@ -0,0 +1,689 @@ +/* + * Aic7xxx SCSI host adapter firmware assembler symbol table implementation + * + * Copyright (c) 1997 Justin T. Gibbs. + * Copyright (c) 2002 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aicasm/aicasm_symbol.c#24 $ + * + * $FreeBSD$ + */ + +#include <sys/types.h> + +#include "aicdb.h" +#include <fcntl.h> +#include <inttypes.h> +#include <regex.h> +#include <stdio.h> +#include <stdlib.h> +#include <string.h> +#include <sysexits.h> + +#include "aicasm_symbol.h" +#include "aicasm.h" + +static DB *symtable; + +symbol_t * +symbol_create(char *name) +{ + symbol_t *new_symbol; + + new_symbol = (symbol_t *)malloc(sizeof(symbol_t)); + if (new_symbol == NULL) { + perror("Unable to create new symbol"); + exit(EX_SOFTWARE); + } + memset(new_symbol, 0, sizeof(*new_symbol)); + new_symbol->name = strdup(name); + if (new_symbol->name == NULL) + stop("Unable to strdup symbol name", EX_SOFTWARE); + new_symbol->type = UNINITIALIZED; + new_symbol->count = 1; + return (new_symbol); +} + +void +symbol_delete(symbol_t *symbol) +{ + if (symtable != NULL) { + DBT key; + + key.data = symbol->name; + key.size = strlen(symbol->name); + symtable->del(symtable, &key, /*flags*/0); + } + switch(symbol->type) { + case SCBLOC: + case SRAMLOC: + case REGISTER: + if (symbol->info.rinfo != NULL) + free(symbol->info.rinfo); + break; + case ALIAS: + if (symbol->info.ainfo != NULL) + free(symbol->info.ainfo); + break; + case MASK: + case FIELD: + case ENUM: + case ENUM_ENTRY: + if (symbol->info.finfo != NULL) { + symlist_free(&symbol->info.finfo->symrefs); + free(symbol->info.finfo); + } + break; + case DOWNLOAD_CONST: + case CONST: + if (symbol->info.cinfo != NULL) + free(symbol->info.cinfo); + break; + case LABEL: + if (symbol->info.linfo != NULL) + free(symbol->info.linfo); + break; + case UNINITIALIZED: + default: + break; + } + free(symbol->name); + free(symbol); +} + +void +symtable_open() +{ + symtable = dbopen(/*filename*/NULL, + O_CREAT | O_NONBLOCK | O_RDWR, /*mode*/0, DB_HASH, + /*openinfo*/NULL); + + if (symtable == NULL) { + perror("Symbol table creation failed"); + exit(EX_SOFTWARE); + /* NOTREACHED */ + } +} + +void +symtable_close() +{ + if (symtable != NULL) { + DBT key; + DBT data; + + while (symtable->seq(symtable, &key, &data, R_FIRST) == 0) { + symbol_t *stored_ptr; + + memcpy(&stored_ptr, data.data, sizeof(stored_ptr)); + symbol_delete(stored_ptr); + } + symtable->close(symtable); + } +} + +/* + * The semantics of get is to return an uninitialized symbol entry + * if a lookup fails. + */ +symbol_t * +symtable_get(char *name) +{ + symbol_t *stored_ptr; + DBT key; + DBT data; + int retval; + + key.data = (void *)name; + key.size = strlen(name); + + if ((retval = symtable->get(symtable, &key, &data, /*flags*/0)) != 0) { + if (retval == -1) { + perror("Symbol table get operation failed"); + exit(EX_SOFTWARE); + /* NOTREACHED */ + } else if (retval == 1) { + /* Symbol wasn't found, so create a new one */ + symbol_t *new_symbol; + + new_symbol = symbol_create(name); + data.data = &new_symbol; + data.size = sizeof(new_symbol); + if (symtable->put(symtable, &key, &data, + /*flags*/0) !=0) { + perror("Symtable put failed"); + exit(EX_SOFTWARE); + } + return (new_symbol); + } else { + perror("Unexpected return value from db get routine"); + exit(EX_SOFTWARE); + /* NOTREACHED */ + } + } + memcpy(&stored_ptr, data.data, sizeof(stored_ptr)); + stored_ptr->count++; + data.data = &stored_ptr; + if (symtable->put(symtable, &key, &data, /*flags*/0) !=0) { + perror("Symtable put failed"); + exit(EX_SOFTWARE); + } + return (stored_ptr); +} + +symbol_node_t * +symlist_search(symlist_t *symlist, char *symname) +{ + symbol_node_t *curnode; + + curnode = SLIST_FIRST(symlist); + while(curnode != NULL) { + if (strcmp(symname, curnode->symbol->name) == 0) + break; + curnode = SLIST_NEXT(curnode, links); + } + return (curnode); +} + +void +symlist_add(symlist_t *symlist, symbol_t *symbol, int how) +{ + symbol_node_t *newnode; + + newnode = (symbol_node_t *)malloc(sizeof(symbol_node_t)); + if (newnode == NULL) { + stop("symlist_add: Unable to malloc symbol_node", EX_SOFTWARE); + /* NOTREACHED */ + } + newnode->symbol = symbol; + if (how == SYMLIST_SORT) { + symbol_node_t *curnode; + int field; + + field = FALSE; + switch(symbol->type) { + case REGISTER: + case SCBLOC: + case SRAMLOC: + break; + case FIELD: + case MASK: + case ENUM: + case ENUM_ENTRY: + field = TRUE; + break; + default: + stop("symlist_add: Invalid symbol type for sorting", + EX_SOFTWARE); + /* NOTREACHED */ + } + + curnode = SLIST_FIRST(symlist); + if (curnode == NULL + || (field + && (curnode->symbol->type > newnode->symbol->type + || (curnode->symbol->type == newnode->symbol->type + && (curnode->symbol->info.finfo->value > + newnode->symbol->info.finfo->value)))) + || (!field && (curnode->symbol->info.rinfo->address > + newnode->symbol->info.rinfo->address))) { + SLIST_INSERT_HEAD(symlist, newnode, links); + return; + } + + while (1) { + if (SLIST_NEXT(curnode, links) == NULL) { + SLIST_INSERT_AFTER(curnode, newnode, + links); + break; + } else { + symbol_t *cursymbol; + + cursymbol = SLIST_NEXT(curnode, links)->symbol; + if ((field + && (cursymbol->type > symbol->type + || (cursymbol->type == symbol->type + && (cursymbol->info.finfo->value > + symbol->info.finfo->value)))) + || (!field + && (cursymbol->info.rinfo->address > + symbol->info.rinfo->address))) { + SLIST_INSERT_AFTER(curnode, newnode, + links); + break; + } + } + curnode = SLIST_NEXT(curnode, links); + } + } else { + SLIST_INSERT_HEAD(symlist, newnode, links); + } +} + +void +symlist_free(symlist_t *symlist) +{ + symbol_node_t *node1, *node2; + + node1 = SLIST_FIRST(symlist); + while (node1 != NULL) { + node2 = SLIST_NEXT(node1, links); + free(node1); + node1 = node2; + } + SLIST_INIT(symlist); +} + +void +symlist_merge(symlist_t *symlist_dest, symlist_t *symlist_src1, + symlist_t *symlist_src2) +{ + symbol_node_t *node; + + *symlist_dest = *symlist_src1; + while((node = SLIST_FIRST(symlist_src2)) != NULL) { + SLIST_REMOVE_HEAD(symlist_src2, links); + SLIST_INSERT_HEAD(symlist_dest, node, links); + } + + /* These are now empty */ + SLIST_INIT(symlist_src1); + SLIST_INIT(symlist_src2); +} + +void +aic_print_file_prologue(FILE *ofile) +{ + + if (ofile == NULL) + return; + + fprintf(ofile, +"/*\n" +" * DO NOT EDIT - This file is automatically generated\n" +" * from the following source files:\n" +" *\n" +"%s */\n", + versions); +} + +void +aic_print_include(FILE *dfile, char *include_file) +{ + + if (dfile == NULL) + return; + fprintf(dfile, "\n#include \"%s\"\n\n", include_file); +} + +void +aic_print_reg_dump_types(FILE *ofile) +{ + if (ofile == NULL) + return; + + fprintf(ofile, +"typedef int (%sreg_print_t)(u_int, u_int *, u_int);\n" +"typedef struct %sreg_parse_entry {\n" +" char *name;\n" +" uint8_t value;\n" +" uint8_t mask;\n" +"} %sreg_parse_entry_t;\n" +"\n", + prefix, prefix, prefix); +} + +static void +aic_print_reg_dump_start(FILE *dfile, symbol_node_t *regnode) +{ + if (dfile == NULL) + return; + + fprintf(dfile, +"static const %sreg_parse_entry_t %s_parse_table[] = {\n", + prefix, + regnode->symbol->name); +} + +static void +aic_print_reg_dump_end(FILE *ofile, FILE *dfile, + symbol_node_t *regnode, u_int num_entries) +{ + char *lower_name; + char *letter; + + lower_name = strdup(regnode->symbol->name); + if (lower_name == NULL) + stop("Unable to strdup symbol name", EX_SOFTWARE); + + for (letter = lower_name; *letter != '\0'; letter++) + *letter = tolower(*letter); + + if (dfile != NULL) { + if (num_entries != 0) + fprintf(dfile, +"\n" +"};\n" +"\n"); + + fprintf(dfile, +"int\n" +"%s%s_print(u_int regvalue, u_int *cur_col, u_int wrap)\n" +"{\n" +" return (%sprint_register(%s%s, %d, \"%s\",\n" +" 0x%02x, regvalue, cur_col, wrap));\n" +"}\n" +"\n", + prefix, + lower_name, + prefix, + num_entries != 0 ? regnode->symbol->name : "NULL", + num_entries != 0 ? "_parse_table" : "", + num_entries, + regnode->symbol->name, + regnode->symbol->info.rinfo->address); + } + + fprintf(ofile, +"#if AIC_DEBUG_REGISTERS\n" +"%sreg_print_t %s%s_print;\n" +"#else\n" +"#define %s%s_print(regvalue, cur_col, wrap) \\\n" +" %sprint_register(NULL, 0, \"%s\", 0x%02x, regvalue, cur_col, wrap)\n" +"#endif\n" +"\n", + prefix, + prefix, + lower_name, + prefix, + lower_name, + prefix, + regnode->symbol->name, + regnode->symbol->info.rinfo->address); +} + +static void +aic_print_reg_dump_entry(FILE *dfile, symbol_node_t *curnode) +{ + int num_tabs; + + if (dfile == NULL) + return; + + fprintf(dfile, +" { \"%s\",", + curnode->symbol->name); + + num_tabs = 3 - (strlen(curnode->symbol->name) + 5) / 8; + + while (num_tabs-- > 0) + fputc('\t', dfile); + fprintf(dfile, "0x%02x, 0x%02x }", + curnode->symbol->info.finfo->value, + curnode->symbol->info.finfo->mask); +} + +void +symtable_dump(FILE *ofile, FILE *dfile) +{ + /* + * Sort the registers by address with a simple insertion sort. + * Put bitmasks next to the first register that defines them. + * Put constants at the end. + */ + symlist_t registers; + symlist_t masks; + symlist_t constants; + symlist_t download_constants; + symlist_t aliases; + symlist_t exported_labels; + symbol_node_t *curnode; + symbol_node_t *regnode; + DBT key; + DBT data; + int flag; + int reg_count = 0, reg_used = 0; + u_int i; + + if (symtable == NULL) + return; + + SLIST_INIT(®isters); + SLIST_INIT(&masks); + SLIST_INIT(&constants); + SLIST_INIT(&download_constants); + SLIST_INIT(&aliases); + SLIST_INIT(&exported_labels); + flag = R_FIRST; + while (symtable->seq(symtable, &key, &data, flag) == 0) { + symbol_t *cursym; + + memcpy(&cursym, data.data, sizeof(cursym)); + switch(cursym->type) { + case REGISTER: + case SCBLOC: + case SRAMLOC: + symlist_add(®isters, cursym, SYMLIST_SORT); + break; + case MASK: + case FIELD: + case ENUM: + case ENUM_ENTRY: + symlist_add(&masks, cursym, SYMLIST_SORT); + break; + case CONST: + symlist_add(&constants, cursym, + SYMLIST_INSERT_HEAD); + break; + case DOWNLOAD_CONST: + symlist_add(&download_constants, cursym, + SYMLIST_INSERT_HEAD); + break; + case ALIAS: + symlist_add(&aliases, cursym, + SYMLIST_INSERT_HEAD); + break; + case LABEL: + if (cursym->info.linfo->exported == 0) + break; + symlist_add(&exported_labels, cursym, + SYMLIST_INSERT_HEAD); + break; + default: + break; + } + flag = R_NEXT; + } + + /* Register dianostic functions/declarations first. */ + aic_print_file_prologue(ofile); + aic_print_reg_dump_types(ofile); + aic_print_file_prologue(dfile); + aic_print_include(dfile, stock_include_file); + SLIST_FOREACH(curnode, ®isters, links) { + + if (curnode->symbol->dont_generate_debug_code) + continue; + + switch(curnode->symbol->type) { + case REGISTER: + case SCBLOC: + case SRAMLOC: + { + symlist_t *fields; + symbol_node_t *fieldnode; + int num_entries; + + num_entries = 0; + reg_count++; + if (curnode->symbol->count == 1) + break; + fields = &curnode->symbol->info.rinfo->fields; + SLIST_FOREACH(fieldnode, fields, links) { + if (num_entries == 0) + aic_print_reg_dump_start(dfile, + curnode); + else if (dfile != NULL) + fputs(",\n", dfile); + num_entries++; + aic_print_reg_dump_entry(dfile, fieldnode); + } + aic_print_reg_dump_end(ofile, dfile, + curnode, num_entries); + reg_used++; + } + default: + break; + } + } + fprintf(stderr, "%s: %d of %d register definitions used\n", appname, + reg_used, reg_count); + + /* Fold in the masks and bits */ + while (SLIST_FIRST(&masks) != NULL) { + char *regname; + + curnode = SLIST_FIRST(&masks); + SLIST_REMOVE_HEAD(&masks, links); + + regnode = SLIST_FIRST(&curnode->symbol->info.finfo->symrefs); + regname = regnode->symbol->name; + regnode = symlist_search(®isters, regname); + SLIST_INSERT_AFTER(regnode, curnode, links); + } + + /* Add the aliases */ + while (SLIST_FIRST(&aliases) != NULL) { + char *regname; + + curnode = SLIST_FIRST(&aliases); + SLIST_REMOVE_HEAD(&aliases, links); + + regname = curnode->symbol->info.ainfo->parent->name; + regnode = symlist_search(®isters, regname); + SLIST_INSERT_AFTER(regnode, curnode, links); + } + + /* Output generated #defines. */ + while (SLIST_FIRST(®isters) != NULL) { + symbol_node_t *curnode; + u_int value; + char *tab_str; + char *tab_str2; + + curnode = SLIST_FIRST(®isters); + SLIST_REMOVE_HEAD(®isters, links); + switch(curnode->symbol->type) { + case REGISTER: + case SCBLOC: + case SRAMLOC: + fprintf(ofile, "\n"); + value = curnode->symbol->info.rinfo->address; + tab_str = "\t"; + tab_str2 = "\t\t"; + break; + case ALIAS: + { + symbol_t *parent; + + parent = curnode->symbol->info.ainfo->parent; + value = parent->info.rinfo->address; + tab_str = "\t"; + tab_str2 = "\t\t"; + break; + } + case MASK: + case FIELD: + case ENUM: + case ENUM_ENTRY: + value = curnode->symbol->info.finfo->value; + tab_str = "\t\t"; + tab_str2 = "\t"; + break; + default: + value = 0; /* Quiet compiler */ + tab_str = NULL; + tab_str2 = NULL; + stop("symtable_dump: Invalid symbol type " + "encountered", EX_SOFTWARE); + break; + } + fprintf(ofile, "#define%s%-16s%s0x%02x\n", + tab_str, curnode->symbol->name, tab_str2, + value); + free(curnode); + } + fprintf(ofile, "\n\n"); + + while (SLIST_FIRST(&constants) != NULL) { + symbol_node_t *curnode; + + curnode = SLIST_FIRST(&constants); + SLIST_REMOVE_HEAD(&constants, links); + fprintf(ofile, "#define\t%-8s\t0x%02x\n", + curnode->symbol->name, + curnode->symbol->info.cinfo->value); + free(curnode); + } + + fprintf(ofile, "\n\n/* Downloaded Constant Definitions */\n"); + + for (i = 0; SLIST_FIRST(&download_constants) != NULL; i++) { + symbol_node_t *curnode; + + curnode = SLIST_FIRST(&download_constants); + SLIST_REMOVE_HEAD(&download_constants, links); + fprintf(ofile, "#define\t%-8s\t0x%02x\n", + curnode->symbol->name, + curnode->symbol->info.cinfo->value); + free(curnode); + } + fprintf(ofile, "#define\tDOWNLOAD_CONST_COUNT\t0x%02x\n", i); + + fprintf(ofile, "\n\n/* Exported Labels */\n"); + + while (SLIST_FIRST(&exported_labels) != NULL) { + symbol_node_t *curnode; + + curnode = SLIST_FIRST(&exported_labels); + SLIST_REMOVE_HEAD(&exported_labels, links); + fprintf(ofile, "#define\tLABEL_%-8s\t0x%02x\n", + curnode->symbol->name, + curnode->symbol->info.linfo->address); + free(curnode); + } +} + diff --git a/drivers/scsi/aic7xxx/aicasm/aicasm_symbol.h b/drivers/scsi/aic7xxx/aicasm/aicasm_symbol.h new file mode 100644 index 000000000..7bf7fd595 --- /dev/null +++ b/drivers/scsi/aic7xxx/aicasm/aicasm_symbol.h @@ -0,0 +1,205 @@ +/* + * Aic7xxx SCSI host adapter firmware assembler symbol table definitions + * + * Copyright (c) 1997 Justin T. Gibbs. + * Copyright (c) 2002 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aicasm/aicasm_symbol.h#17 $ + * + * $FreeBSD$ + */ + +#include "../queue.h" + +typedef enum { + UNINITIALIZED, + REGISTER, + ALIAS, + SCBLOC, + SRAMLOC, + ENUM_ENTRY, + FIELD, + MASK, + ENUM, + CONST, + DOWNLOAD_CONST, + LABEL, + CONDITIONAL, + MACRO +} symtype; + +typedef enum { + RO = 0x01, + WO = 0x02, + RW = 0x03 +}amode_t; + +typedef SLIST_HEAD(symlist, symbol_node) symlist_t; + +struct reg_info { + u_int address; + int size; + amode_t mode; + symlist_t fields; + uint8_t valid_bitmask; + uint8_t modes; + int typecheck_masks; +}; + +struct field_info { + symlist_t symrefs; + uint8_t value; + uint8_t mask; +}; + +struct const_info { + u_int value; + int define; +}; + +struct alias_info { + struct symbol *parent; +}; + +struct label_info { + int address; + int exported; +}; + +struct cond_info { + int func_num; +}; + +struct macro_arg { + STAILQ_ENTRY(macro_arg) links; + regex_t arg_regex; + char *replacement_text; +}; +STAILQ_HEAD(macro_arg_list, macro_arg) args; + +struct macro_info { + struct macro_arg_list args; + int narg; + const char* body; +}; + +typedef struct expression_info { + symlist_t referenced_syms; + int value; +} expression_t; + +typedef struct symbol { + char *name; + symtype type; + int count; + union { + struct reg_info *rinfo; + struct field_info *finfo; + struct const_info *cinfo; + struct alias_info *ainfo; + struct label_info *linfo; + struct cond_info *condinfo; + struct macro_info *macroinfo; + } info; + int dont_generate_debug_code; +} symbol_t; + +typedef struct symbol_ref { + symbol_t *symbol; + int offset; +} symbol_ref_t; + +typedef struct symbol_node { + SLIST_ENTRY(symbol_node) links; + symbol_t *symbol; +} symbol_node_t; + +typedef struct critical_section { + TAILQ_ENTRY(critical_section) links; + int begin_addr; + int end_addr; +} critical_section_t; + +typedef enum { + SCOPE_ROOT, + SCOPE_IF, + SCOPE_ELSE_IF, + SCOPE_ELSE +} scope_type; + +typedef struct patch_info { + int skip_patch; + int skip_instr; +} patch_info_t; + +typedef struct scope { + SLIST_ENTRY(scope) scope_stack_links; + TAILQ_ENTRY(scope) scope_links; + TAILQ_HEAD(, scope) inner_scope; + scope_type type; + int inner_scope_patches; + int begin_addr; + int end_addr; + patch_info_t patches[2]; + int func_num; +} scope_t; + +TAILQ_HEAD(cs_tailq, critical_section); +SLIST_HEAD(scope_list, scope); +TAILQ_HEAD(scope_tailq, scope); + +void symbol_delete(symbol_t *symbol); + +void symtable_open(void); + +void symtable_close(void); + +symbol_t * + symtable_get(char *name); + +symbol_node_t * + symlist_search(symlist_t *symlist, char *symname); + +void + symlist_add(symlist_t *symlist, symbol_t *symbol, int how); +#define SYMLIST_INSERT_HEAD 0x00 +#define SYMLIST_SORT 0x01 + +void symlist_free(symlist_t *symlist); + +void symlist_merge(symlist_t *symlist_dest, symlist_t *symlist_src1, + symlist_t *symlist_src2); +void symtable_dump(FILE *ofile, FILE *dfile); diff --git a/drivers/scsi/aic7xxx/aiclib.h b/drivers/scsi/aic7xxx/aiclib.h new file mode 100644 index 000000000..f8fd198aa --- /dev/null +++ b/drivers/scsi/aic7xxx/aiclib.h @@ -0,0 +1,195 @@ +/* + * Largely written by Julian Elischer (julian@tfs.com) + * for TRW Financial Systems. + * + * TRW Financial Systems, in accordance with their agreement with Carnegie + * Mellon University, makes this software available to CMU to distribute + * or use in any manner that they see fit as long as this message is kept with + * the software. For this reason TFS also grants any other persons or + * organisations permission to use or modify this software. + * + * TFS supplies this software to be publicly redistributed + * on the understanding that TFS is not responsible for the correct + * functioning of this software in any circumstances. + * + * Ported to run under 386BSD by Julian Elischer (julian@tfs.com) Sept 1992 + * + * $FreeBSD: src/sys/cam/scsi/scsi_all.h,v 1.21 2002/10/08 17:12:44 ken Exp $ + * + * Copyright (c) 2003 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id$ + */ + +#ifndef _AICLIB_H +#define _AICLIB_H + +struct scsi_sense +{ + uint8_t opcode; + uint8_t byte2; + uint8_t unused[2]; + uint8_t length; + uint8_t control; +}; + +#define SCSI_REV_0 0 +#define SCSI_REV_CCS 1 +#define SCSI_REV_2 2 +#define SCSI_REV_SPC 3 +#define SCSI_REV_SPC2 4 + +struct scsi_sense_data +{ + uint8_t error_code; +#define SSD_ERRCODE 0x7F +#define SSD_CURRENT_ERROR 0x70 +#define SSD_DEFERRED_ERROR 0x71 +#define SSD_ERRCODE_VALID 0x80 + uint8_t segment; + uint8_t flags; +#define SSD_KEY 0x0F +#define SSD_KEY_NO_SENSE 0x00 +#define SSD_KEY_RECOVERED_ERROR 0x01 +#define SSD_KEY_NOT_READY 0x02 +#define SSD_KEY_MEDIUM_ERROR 0x03 +#define SSD_KEY_HARDWARE_ERROR 0x04 +#define SSD_KEY_ILLEGAL_REQUEST 0x05 +#define SSD_KEY_UNIT_ATTENTION 0x06 +#define SSD_KEY_DATA_PROTECT 0x07 +#define SSD_KEY_BLANK_CHECK 0x08 +#define SSD_KEY_Vendor_Specific 0x09 +#define SSD_KEY_COPY_ABORTED 0x0a +#define SSD_KEY_ABORTED_COMMAND 0x0b +#define SSD_KEY_EQUAL 0x0c +#define SSD_KEY_VOLUME_OVERFLOW 0x0d +#define SSD_KEY_MISCOMPARE 0x0e +#define SSD_KEY_RESERVED 0x0f +#define SSD_ILI 0x20 +#define SSD_EOM 0x40 +#define SSD_FILEMARK 0x80 + uint8_t info[4]; + uint8_t extra_len; + uint8_t cmd_spec_info[4]; + uint8_t add_sense_code; + uint8_t add_sense_code_qual; + uint8_t fru; + uint8_t sense_key_spec[3]; +#define SSD_SCS_VALID 0x80 +#define SSD_FIELDPTR_CMD 0x40 +#define SSD_BITPTR_VALID 0x08 +#define SSD_BITPTR_VALUE 0x07 +#define SSD_MIN_SIZE 18 + uint8_t extra_bytes[14]; +#define SSD_FULL_SIZE sizeof(struct scsi_sense_data) +}; + +/* + * Status Byte + */ +#define SCSI_STATUS_OK 0x00 +#define SCSI_STATUS_CHECK_COND 0x02 +#define SCSI_STATUS_COND_MET 0x04 +#define SCSI_STATUS_BUSY 0x08 +#define SCSI_STATUS_INTERMED 0x10 +#define SCSI_STATUS_INTERMED_COND_MET 0x14 +#define SCSI_STATUS_RESERV_CONFLICT 0x18 +#define SCSI_STATUS_CMD_TERMINATED 0x22 /* Obsolete in SAM-2 */ +#define SCSI_STATUS_QUEUE_FULL 0x28 +#define SCSI_STATUS_ACA_ACTIVE 0x30 +#define SCSI_STATUS_TASK_ABORTED 0x40 + +/************************* Large Disk Handling ********************************/ +static inline int +aic_sector_div(sector_t capacity, int heads, int sectors) +{ + /* ugly, ugly sector_div calling convention.. */ + sector_div(capacity, (heads * sectors)); + return (int)capacity; +} + +static inline uint32_t +scsi_4btoul(uint8_t *bytes) +{ + uint32_t rv; + + rv = (bytes[0] << 24) | + (bytes[1] << 16) | + (bytes[2] << 8) | + bytes[3]; + return (rv); +} + +/* Macros for generating the elements of the PCI ID tables. */ + +#define GETID(v, s) (unsigned)(((v) >> (s)) & 0xFFFF ?: PCI_ANY_ID) + +#define ID_C(x, c) \ +{ \ + GETID(x,32), GETID(x,48), GETID(x,0), GETID(x,16), \ + (c) << 8, 0xFFFF00, 0 \ +} + +#define ID2C(x) \ + ID_C(x, PCI_CLASS_STORAGE_SCSI), \ + ID_C(x, PCI_CLASS_STORAGE_RAID) + +#define IDIROC(x) ((x) | ~ID_ALL_IROC_MASK) + +/* Generate IDs for all 16 possibilites. + * The argument has already masked out + * the 4 least significant bits of the device id. + * (e.g., mask: ID_9005_GENERIC_MASK). + */ +#define ID16(x) \ + ID(x), \ + ID((x) | 0x0001000000000000ull), \ + ID((x) | 0x0002000000000000ull), \ + ID((x) | 0x0003000000000000ull), \ + ID((x) | 0x0004000000000000ull), \ + ID((x) | 0x0005000000000000ull), \ + ID((x) | 0x0006000000000000ull), \ + ID((x) | 0x0007000000000000ull), \ + ID((x) | 0x0008000000000000ull), \ + ID((x) | 0x0009000000000000ull), \ + ID((x) | 0x000A000000000000ull), \ + ID((x) | 0x000B000000000000ull), \ + ID((x) | 0x000C000000000000ull), \ + ID((x) | 0x000D000000000000ull), \ + ID((x) | 0x000E000000000000ull), \ + ID((x) | 0x000F000000000000ull) + +#endif /*_AICLIB_H */ diff --git a/drivers/scsi/aic7xxx/cam.h b/drivers/scsi/aic7xxx/cam.h new file mode 100644 index 000000000..687aef6ef --- /dev/null +++ b/drivers/scsi/aic7xxx/cam.h @@ -0,0 +1,111 @@ +/* + * Data structures and definitions for the CAM system. + * + * Copyright (c) 1997 Justin T. Gibbs. + * Copyright (c) 2000 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. The name of the author may not be used to endorse or promote products + * derived from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL"). + * + * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR + * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/cam.h#15 $ + */ + +#ifndef _AIC7XXX_CAM_H +#define _AIC7XXX_CAM_H 1 + +#include <linux/types.h> + +#define CAM_BUS_WILDCARD ((u_int)~0) +#define CAM_TARGET_WILDCARD ((u_int)~0) +#define CAM_LUN_WILDCARD ((u_int)~0) + +/* CAM Status field values */ +typedef enum { + CAM_REQ_INPROG, /* CCB request is in progress */ + CAM_REQ_CMP, /* CCB request completed without error */ + CAM_REQ_ABORTED, /* CCB request aborted by the host */ + CAM_UA_ABORT, /* Unable to abort CCB request */ + CAM_REQ_CMP_ERR, /* CCB request completed with an error */ + CAM_BUSY, /* CAM subsystem is busy */ + CAM_REQ_INVALID, /* CCB request was invalid */ + CAM_PATH_INVALID, /* Supplied Path ID is invalid */ + CAM_SEL_TIMEOUT, /* Target Selection Timeout */ + CAM_CMD_TIMEOUT, /* Command timeout */ + CAM_SCSI_STATUS_ERROR, /* SCSI error, look at error code in CCB */ + CAM_SCSI_BUS_RESET, /* SCSI Bus Reset Sent/Received */ + CAM_UNCOR_PARITY, /* Uncorrectable parity error occurred */ + CAM_AUTOSENSE_FAIL, /* Autosense: request sense cmd fail */ + CAM_NO_HBA, /* No HBA Detected Error */ + CAM_DATA_RUN_ERR, /* Data Overrun error */ + CAM_UNEXP_BUSFREE, /* Unexpected Bus Free */ + CAM_SEQUENCE_FAIL, /* Protocol Violation */ + CAM_CCB_LEN_ERR, /* CCB length supplied is inadequate */ + CAM_PROVIDE_FAIL, /* Unable to provide requested capability */ + CAM_BDR_SENT, /* A SCSI BDR msg was sent to target */ + CAM_REQ_TERMIO, /* CCB request terminated by the host */ + CAM_UNREC_HBA_ERROR, /* Unrecoverable Host Bus Adapter Error */ + CAM_REQ_TOO_BIG, /* The request was too large for this host */ + CAM_UA_TERMIO, /* Unable to terminate I/O CCB request */ + CAM_MSG_REJECT_REC, /* Message Reject Received */ + CAM_DEV_NOT_THERE, /* SCSI Device Not Installed/there */ + CAM_RESRC_UNAVAIL, /* Resource Unavailable */ + /* + * This request should be requeued to preserve + * transaction ordering. This typically occurs + * when the SIM recognizes an error that should + * freeze the queue and must place additional + * requests for the target at the sim level + * back into the XPT queue. + */ + CAM_REQUEUE_REQ, + CAM_DEV_QFRZN = 0x40, + + CAM_STATUS_MASK = 0x3F +} cam_status; + +/* + * Definitions for the asynchronous callback CCB fields. + */ +typedef enum { + AC_GETDEV_CHANGED = 0x800,/* Getdev info might have changed */ + AC_INQ_CHANGED = 0x400,/* Inquiry info might have changed */ + AC_TRANSFER_NEG = 0x200,/* New transfer settings in effect */ + AC_LOST_DEVICE = 0x100,/* A device went away */ + AC_FOUND_DEVICE = 0x080,/* A new device was found */ + AC_PATH_DEREGISTERED = 0x040,/* A path has de-registered */ + AC_PATH_REGISTERED = 0x020,/* A new path has been registered */ + AC_SENT_BDR = 0x010,/* A BDR message was sent to target */ + AC_SCSI_AEN = 0x008,/* A SCSI AEN has been received */ + AC_UNSOL_RESEL = 0x002,/* Unsolicited reselection occurred */ + AC_BUS_RESET = 0x001 /* A SCSI bus reset occurred */ +} ac_code; + +typedef enum { + CAM_DIR_IN = DMA_FROM_DEVICE, + CAM_DIR_OUT = DMA_TO_DEVICE, + CAM_DIR_NONE = DMA_NONE, +} ccb_flags; + +#endif /* _AIC7XXX_CAM_H */ diff --git a/drivers/scsi/aic7xxx/queue.h b/drivers/scsi/aic7xxx/queue.h new file mode 100644 index 000000000..ba602981f --- /dev/null +++ b/drivers/scsi/aic7xxx/queue.h @@ -0,0 +1,501 @@ +/* + * Copyright (c) 1991, 1993 + * The Regents of the University of California. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * + * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * @(#)queue.h 8.5 (Berkeley) 8/20/94 + * $FreeBSD: src/sys/sys/queue.h,v 1.38 2000/05/26 02:06:56 jake Exp $ + */ + +#ifndef _SYS_QUEUE_H_ +#define _SYS_QUEUE_H_ + +/* + * This file defines five types of data structures: singly-linked lists, + * singly-linked tail queues, lists, tail queues, and circular queues. + * + * A singly-linked list is headed by a single forward pointer. The elements + * are singly linked for minimum space and pointer manipulation overhead at + * the expense of O(n) removal for arbitrary elements. New elements can be + * added to the list after an existing element or at the head of the list. + * Elements being removed from the head of the list should use the explicit + * macro for this purpose for optimum efficiency. A singly-linked list may + * only be traversed in the forward direction. Singly-linked lists are ideal + * for applications with large datasets and few or no removals or for + * implementing a LIFO queue. + * + * A singly-linked tail queue is headed by a pair of pointers, one to the + * head of the list and the other to the tail of the list. The elements are + * singly linked for minimum space and pointer manipulation overhead at the + * expense of O(n) removal for arbitrary elements. New elements can be added + * to the list after an existing element, at the head of the list, or at the + * end of the list. Elements being removed from the head of the tail queue + * should use the explicit macro for this purpose for optimum efficiency. + * A singly-linked tail queue may only be traversed in the forward direction. + * Singly-linked tail queues are ideal for applications with large datasets + * and few or no removals or for implementing a FIFO queue. + * + * A list is headed by a single forward pointer (or an array of forward + * pointers for a hash table header). The elements are doubly linked + * so that an arbitrary element can be removed without a need to + * traverse the list. New elements can be added to the list before + * or after an existing element or at the head of the list. A list + * may only be traversed in the forward direction. + * + * A tail queue is headed by a pair of pointers, one to the head of the + * list and the other to the tail of the list. The elements are doubly + * linked so that an arbitrary element can be removed without a need to + * traverse the list. New elements can be added to the list before or + * after an existing element, at the head of the list, or at the end of + * the list. A tail queue may be traversed in either direction. + * + * A circle queue is headed by a pair of pointers, one to the head of the + * list and the other to the tail of the list. The elements are doubly + * linked so that an arbitrary element can be removed without a need to + * traverse the list. New elements can be added to the list before or after + * an existing element, at the head of the list, or at the end of the list. + * A circle queue may be traversed in either direction, but has a more + * complex end of list detection. + * + * For details on the use of these macros, see the queue(3) manual page. + * + * + * SLIST LIST STAILQ TAILQ CIRCLEQ + * _HEAD + + + + + + * _HEAD_INITIALIZER + + + + + + * _ENTRY + + + + + + * _INIT + + + + + + * _EMPTY + + + + + + * _FIRST + + + + + + * _NEXT + + + + + + * _PREV - - - + + + * _LAST - - + + + + * _FOREACH + + + + + + * _FOREACH_REVERSE - - - + + + * _INSERT_HEAD + + + + + + * _INSERT_BEFORE - + - + + + * _INSERT_AFTER + + + + + + * _INSERT_TAIL - - + + + + * _REMOVE_HEAD + - + - - + * _REMOVE + + + + + + * + */ + +/* + * Singly-linked List declarations. + */ +#define SLIST_HEAD(name, type) \ +struct name { \ + struct type *slh_first; /* first element */ \ +} + +#define SLIST_HEAD_INITIALIZER(head) \ + { NULL } + +#define SLIST_ENTRY(type) \ +struct { \ + struct type *sle_next; /* next element */ \ +} + +/* + * Singly-linked List functions. + */ +#define SLIST_EMPTY(head) ((head)->slh_first == NULL) + +#define SLIST_FIRST(head) ((head)->slh_first) + +#define SLIST_FOREACH(var, head, field) \ + for ((var) = SLIST_FIRST((head)); \ + (var); \ + (var) = SLIST_NEXT((var), field)) + +#define SLIST_INIT(head) do { \ + SLIST_FIRST((head)) = NULL; \ +} while (0) + +#define SLIST_INSERT_AFTER(slistelm, elm, field) do { \ + SLIST_NEXT((elm), field) = SLIST_NEXT((slistelm), field); \ + SLIST_NEXT((slistelm), field) = (elm); \ +} while (0) + +#define SLIST_INSERT_HEAD(head, elm, field) do { \ + SLIST_NEXT((elm), field) = SLIST_FIRST((head)); \ + SLIST_FIRST((head)) = (elm); \ +} while (0) + +#define SLIST_NEXT(elm, field) ((elm)->field.sle_next) + +#define SLIST_REMOVE(head, elm, type, field) do { \ + if (SLIST_FIRST((head)) == (elm)) { \ + SLIST_REMOVE_HEAD((head), field); \ + } \ + else { \ + struct type *curelm = SLIST_FIRST((head)); \ + while (SLIST_NEXT(curelm, field) != (elm)) \ + curelm = SLIST_NEXT(curelm, field); \ + SLIST_NEXT(curelm, field) = \ + SLIST_NEXT(SLIST_NEXT(curelm, field), field); \ + } \ +} while (0) + +#define SLIST_REMOVE_HEAD(head, field) do { \ + SLIST_FIRST((head)) = SLIST_NEXT(SLIST_FIRST((head)), field); \ +} while (0) + +/* + * Singly-linked Tail queue declarations. + */ +#define STAILQ_HEAD(name, type) \ +struct name { \ + struct type *stqh_first;/* first element */ \ + struct type **stqh_last;/* addr of last next element */ \ +} + +#define STAILQ_HEAD_INITIALIZER(head) \ + { NULL, &(head).stqh_first } + +#define STAILQ_ENTRY(type) \ +struct { \ + struct type *stqe_next; /* next element */ \ +} + +/* + * Singly-linked Tail queue functions. + */ +#define STAILQ_EMPTY(head) ((head)->stqh_first == NULL) + +#define STAILQ_FIRST(head) ((head)->stqh_first) + +#define STAILQ_FOREACH(var, head, field) \ + for((var) = STAILQ_FIRST((head)); \ + (var); \ + (var) = STAILQ_NEXT((var), field)) + +#define STAILQ_INIT(head) do { \ + STAILQ_FIRST((head)) = NULL; \ + (head)->stqh_last = &STAILQ_FIRST((head)); \ +} while (0) + +#define STAILQ_INSERT_AFTER(head, tqelm, elm, field) do { \ + if ((STAILQ_NEXT((elm), field) = STAILQ_NEXT((tqelm), field)) == NULL)\ + (head)->stqh_last = &STAILQ_NEXT((elm), field); \ + STAILQ_NEXT((tqelm), field) = (elm); \ +} while (0) + +#define STAILQ_INSERT_HEAD(head, elm, field) do { \ + if ((STAILQ_NEXT((elm), field) = STAILQ_FIRST((head))) == NULL) \ + (head)->stqh_last = &STAILQ_NEXT((elm), field); \ + STAILQ_FIRST((head)) = (elm); \ +} while (0) + +#define STAILQ_INSERT_TAIL(head, elm, field) do { \ + STAILQ_NEXT((elm), field) = NULL; \ + STAILQ_LAST((head)) = (elm); \ + (head)->stqh_last = &STAILQ_NEXT((elm), field); \ +} while (0) + +#define STAILQ_LAST(head) (*(head)->stqh_last) + +#define STAILQ_NEXT(elm, field) ((elm)->field.stqe_next) + +#define STAILQ_REMOVE(head, elm, type, field) do { \ + if (STAILQ_FIRST((head)) == (elm)) { \ + STAILQ_REMOVE_HEAD(head, field); \ + } \ + else { \ + struct type *curelm = STAILQ_FIRST((head)); \ + while (STAILQ_NEXT(curelm, field) != (elm)) \ + curelm = STAILQ_NEXT(curelm, field); \ + if ((STAILQ_NEXT(curelm, field) = \ + STAILQ_NEXT(STAILQ_NEXT(curelm, field), field)) == NULL)\ + (head)->stqh_last = &STAILQ_NEXT((curelm), field);\ + } \ +} while (0) + +#define STAILQ_REMOVE_HEAD(head, field) do { \ + if ((STAILQ_FIRST((head)) = \ + STAILQ_NEXT(STAILQ_FIRST((head)), field)) == NULL) \ + (head)->stqh_last = &STAILQ_FIRST((head)); \ +} while (0) + +#define STAILQ_REMOVE_HEAD_UNTIL(head, elm, field) do { \ + if ((STAILQ_FIRST((head)) = STAILQ_NEXT((elm), field)) == NULL) \ + (head)->stqh_last = &STAILQ_FIRST((head)); \ +} while (0) + +/* + * List declarations. + */ +#define BSD_LIST_HEAD(name, type) \ +struct name { \ + struct type *lh_first; /* first element */ \ +} + +#define LIST_HEAD_INITIALIZER(head) \ + { NULL } + +#define LIST_ENTRY(type) \ +struct { \ + struct type *le_next; /* next element */ \ + struct type **le_prev; /* address of previous next element */ \ +} + +/* + * List functions. + */ + +#define LIST_EMPTY(head) ((head)->lh_first == NULL) + +#define LIST_FIRST(head) ((head)->lh_first) + +#define LIST_FOREACH(var, head, field) \ + for ((var) = LIST_FIRST((head)); \ + (var); \ + (var) = LIST_NEXT((var), field)) + +#define LIST_INIT(head) do { \ + LIST_FIRST((head)) = NULL; \ +} while (0) + +#define LIST_INSERT_AFTER(listelm, elm, field) do { \ + if ((LIST_NEXT((elm), field) = LIST_NEXT((listelm), field)) != NULL)\ + LIST_NEXT((listelm), field)->field.le_prev = \ + &LIST_NEXT((elm), field); \ + LIST_NEXT((listelm), field) = (elm); \ + (elm)->field.le_prev = &LIST_NEXT((listelm), field); \ +} while (0) + +#define LIST_INSERT_BEFORE(listelm, elm, field) do { \ + (elm)->field.le_prev = (listelm)->field.le_prev; \ + LIST_NEXT((elm), field) = (listelm); \ + *(listelm)->field.le_prev = (elm); \ + (listelm)->field.le_prev = &LIST_NEXT((elm), field); \ +} while (0) + +#define LIST_INSERT_HEAD(head, elm, field) do { \ + if ((LIST_NEXT((elm), field) = LIST_FIRST((head))) != NULL) \ + LIST_FIRST((head))->field.le_prev = &LIST_NEXT((elm), field);\ + LIST_FIRST((head)) = (elm); \ + (elm)->field.le_prev = &LIST_FIRST((head)); \ +} while (0) + +#define LIST_NEXT(elm, field) ((elm)->field.le_next) + +#define LIST_REMOVE(elm, field) do { \ + if (LIST_NEXT((elm), field) != NULL) \ + LIST_NEXT((elm), field)->field.le_prev = \ + (elm)->field.le_prev; \ + *(elm)->field.le_prev = LIST_NEXT((elm), field); \ +} while (0) + +/* + * Tail queue declarations. + */ +#define TAILQ_HEAD(name, type) \ +struct name { \ + struct type *tqh_first; /* first element */ \ + struct type **tqh_last; /* addr of last next element */ \ +} + +#define TAILQ_HEAD_INITIALIZER(head) \ + { NULL, &(head).tqh_first } + +#define TAILQ_ENTRY(type) \ +struct { \ + struct type *tqe_next; /* next element */ \ + struct type **tqe_prev; /* address of previous next element */ \ +} + +/* + * Tail queue functions. + */ +#define TAILQ_EMPTY(head) ((head)->tqh_first == NULL) + +#define TAILQ_FIRST(head) ((head)->tqh_first) + +#define TAILQ_FOREACH(var, head, field) \ + for ((var) = TAILQ_FIRST((head)); \ + (var); \ + (var) = TAILQ_NEXT((var), field)) + +#define TAILQ_FOREACH_REVERSE(var, head, headname, field) \ + for ((var) = TAILQ_LAST((head), headname); \ + (var); \ + (var) = TAILQ_PREV((var), headname, field)) + +#define TAILQ_INIT(head) do { \ + TAILQ_FIRST((head)) = NULL; \ + (head)->tqh_last = &TAILQ_FIRST((head)); \ +} while (0) + +#define TAILQ_INSERT_AFTER(head, listelm, elm, field) do { \ + if ((TAILQ_NEXT((elm), field) = TAILQ_NEXT((listelm), field)) != NULL)\ + TAILQ_NEXT((elm), field)->field.tqe_prev = \ + &TAILQ_NEXT((elm), field); \ + else \ + (head)->tqh_last = &TAILQ_NEXT((elm), field); \ + TAILQ_NEXT((listelm), field) = (elm); \ + (elm)->field.tqe_prev = &TAILQ_NEXT((listelm), field); \ +} while (0) + +#define TAILQ_INSERT_BEFORE(listelm, elm, field) do { \ + (elm)->field.tqe_prev = (listelm)->field.tqe_prev; \ + TAILQ_NEXT((elm), field) = (listelm); \ + *(listelm)->field.tqe_prev = (elm); \ + (listelm)->field.tqe_prev = &TAILQ_NEXT((elm), field); \ +} while (0) + +#define TAILQ_INSERT_HEAD(head, elm, field) do { \ + if ((TAILQ_NEXT((elm), field) = TAILQ_FIRST((head))) != NULL) \ + TAILQ_FIRST((head))->field.tqe_prev = \ + &TAILQ_NEXT((elm), field); \ + else \ + (head)->tqh_last = &TAILQ_NEXT((elm), field); \ + TAILQ_FIRST((head)) = (elm); \ + (elm)->field.tqe_prev = &TAILQ_FIRST((head)); \ +} while (0) + +#define TAILQ_INSERT_TAIL(head, elm, field) do { \ + TAILQ_NEXT((elm), field) = NULL; \ + (elm)->field.tqe_prev = (head)->tqh_last; \ + *(head)->tqh_last = (elm); \ + (head)->tqh_last = &TAILQ_NEXT((elm), field); \ +} while (0) + +#define TAILQ_LAST(head, headname) \ + (*(((struct headname *)((head)->tqh_last))->tqh_last)) + +#define TAILQ_NEXT(elm, field) ((elm)->field.tqe_next) + +#define TAILQ_PREV(elm, headname, field) \ + (*(((struct headname *)((elm)->field.tqe_prev))->tqh_last)) + +#define TAILQ_REMOVE(head, elm, field) do { \ + if ((TAILQ_NEXT((elm), field)) != NULL) \ + TAILQ_NEXT((elm), field)->field.tqe_prev = \ + (elm)->field.tqe_prev; \ + else \ + (head)->tqh_last = (elm)->field.tqe_prev; \ + *(elm)->field.tqe_prev = TAILQ_NEXT((elm), field); \ +} while (0) + +/* + * Circular queue declarations. + */ +#define CIRCLEQ_HEAD(name, type) \ +struct name { \ + struct type *cqh_first; /* first element */ \ + struct type *cqh_last; /* last element */ \ +} + +#define CIRCLEQ_HEAD_INITIALIZER(head) \ + { (void *)&(head), (void *)&(head) } + +#define CIRCLEQ_ENTRY(type) \ +struct { \ + struct type *cqe_next; /* next element */ \ + struct type *cqe_prev; /* previous element */ \ +} + +/* + * Circular queue functions. + */ +#define CIRCLEQ_EMPTY(head) ((head)->cqh_first == (void *)(head)) + +#define CIRCLEQ_FIRST(head) ((head)->cqh_first) + +#define CIRCLEQ_FOREACH(var, head, field) \ + for ((var) = CIRCLEQ_FIRST((head)); \ + (var) != (void *)(head); \ + (var) = CIRCLEQ_NEXT((var), field)) + +#define CIRCLEQ_FOREACH_REVERSE(var, head, field) \ + for ((var) = CIRCLEQ_LAST((head)); \ + (var) != (void *)(head); \ + (var) = CIRCLEQ_PREV((var), field)) + +#define CIRCLEQ_INIT(head) do { \ + CIRCLEQ_FIRST((head)) = (void *)(head); \ + CIRCLEQ_LAST((head)) = (void *)(head); \ +} while (0) + +#define CIRCLEQ_INSERT_AFTER(head, listelm, elm, field) do { \ + CIRCLEQ_NEXT((elm), field) = CIRCLEQ_NEXT((listelm), field); \ + CIRCLEQ_PREV((elm), field) = (listelm); \ + if (CIRCLEQ_NEXT((listelm), field) == (void *)(head)) \ + CIRCLEQ_LAST((head)) = (elm); \ + else \ + CIRCLEQ_PREV(CIRCLEQ_NEXT((listelm), field), field) = (elm);\ + CIRCLEQ_NEXT((listelm), field) = (elm); \ +} while (0) + +#define CIRCLEQ_INSERT_BEFORE(head, listelm, elm, field) do { \ + CIRCLEQ_NEXT((elm), field) = (listelm); \ + CIRCLEQ_PREV((elm), field) = CIRCLEQ_PREV((listelm), field); \ + if (CIRCLEQ_PREV((listelm), field) == (void *)(head)) \ + CIRCLEQ_FIRST((head)) = (elm); \ + else \ + CIRCLEQ_NEXT(CIRCLEQ_PREV((listelm), field), field) = (elm);\ + CIRCLEQ_PREV((listelm), field) = (elm); \ +} while (0) + +#define CIRCLEQ_INSERT_HEAD(head, elm, field) do { \ + CIRCLEQ_NEXT((elm), field) = CIRCLEQ_FIRST((head)); \ + CIRCLEQ_PREV((elm), field) = (void *)(head); \ + if (CIRCLEQ_LAST((head)) == (void *)(head)) \ + CIRCLEQ_LAST((head)) = (elm); \ + else \ + CIRCLEQ_PREV(CIRCLEQ_FIRST((head)), field) = (elm); \ + CIRCLEQ_FIRST((head)) = (elm); \ +} while (0) + +#define CIRCLEQ_INSERT_TAIL(head, elm, field) do { \ + CIRCLEQ_NEXT((elm), field) = (void *)(head); \ + CIRCLEQ_PREV((elm), field) = CIRCLEQ_LAST((head)); \ + if (CIRCLEQ_FIRST((head)) == (void *)(head)) \ + CIRCLEQ_FIRST((head)) = (elm); \ + else \ + CIRCLEQ_NEXT(CIRCLEQ_LAST((head)), field) = (elm); \ + CIRCLEQ_LAST((head)) = (elm); \ +} while (0) + +#define CIRCLEQ_LAST(head) ((head)->cqh_last) + +#define CIRCLEQ_NEXT(elm,field) ((elm)->field.cqe_next) + +#define CIRCLEQ_PREV(elm,field) ((elm)->field.cqe_prev) + +#define CIRCLEQ_REMOVE(head, elm, field) do { \ + if (CIRCLEQ_NEXT((elm), field) == (void *)(head)) \ + CIRCLEQ_LAST((head)) = CIRCLEQ_PREV((elm), field); \ + else \ + CIRCLEQ_PREV(CIRCLEQ_NEXT((elm), field), field) = \ + CIRCLEQ_PREV((elm), field); \ + if (CIRCLEQ_PREV((elm), field) == (void *)(head)) \ + CIRCLEQ_FIRST((head)) = CIRCLEQ_NEXT((elm), field); \ + else \ + CIRCLEQ_NEXT(CIRCLEQ_PREV((elm), field), field) = \ + CIRCLEQ_NEXT((elm), field); \ +} while (0) + +#endif /* !_SYS_QUEUE_H_ */ diff --git a/drivers/scsi/aic7xxx/scsi_iu.h b/drivers/scsi/aic7xxx/scsi_iu.h new file mode 100644 index 000000000..0eafd3c17 --- /dev/null +++ b/drivers/scsi/aic7xxx/scsi_iu.h @@ -0,0 +1,39 @@ +/* + * This file is in the public domain. + */ +#ifndef _SCSI_SCSI_IU_H +#define _SCSI_SCSI_IU_H 1 + +struct scsi_status_iu_header +{ + u_int8_t reserved[2]; + u_int8_t flags; +#define SIU_SNSVALID 0x2 +#define SIU_RSPVALID 0x1 + u_int8_t status; + u_int8_t sense_length[4]; + u_int8_t pkt_failures_length[4]; + u_int8_t pkt_failures[1]; +}; + +#define SIU_PKTFAIL_OFFSET(siu) 12 +#define SIU_PKTFAIL_CODE(siu) (scsi_4btoul((siu)->pkt_failures) & 0xFF) +#define SIU_PFC_NONE 0 +#define SIU_PFC_CIU_FIELDS_INVALID 2 +#define SIU_PFC_TMF_NOT_SUPPORTED 4 +#define SIU_PFC_TMF_FAILED 5 +#define SIU_PFC_INVALID_TYPE_CODE 6 +#define SIU_PFC_ILLEGAL_REQUEST 7 +#define SIU_SENSE_OFFSET(siu) \ + (12 + (((siu)->flags & SIU_RSPVALID) \ + ? scsi_4btoul((siu)->pkt_failures_length) \ + : 0)) + +#define SIU_TASKMGMT_NONE 0x00 +#define SIU_TASKMGMT_ABORT_TASK 0x01 +#define SIU_TASKMGMT_ABORT_TASK_SET 0x02 +#define SIU_TASKMGMT_CLEAR_TASK_SET 0x04 +#define SIU_TASKMGMT_LUN_RESET 0x08 +#define SIU_TASKMGMT_TARGET_RESET 0x20 +#define SIU_TASKMGMT_CLEAR_ACA 0x40 +#endif /*_SCSI_SCSI_IU_H*/ diff --git a/drivers/scsi/aic7xxx/scsi_message.h b/drivers/scsi/aic7xxx/scsi_message.h new file mode 100644 index 000000000..75811e245 --- /dev/null +++ b/drivers/scsi/aic7xxx/scsi_message.h @@ -0,0 +1,70 @@ +/* + * This file is in the public domain. + * $FreeBSD: src/sys/cam/scsi/scsi_message.h,v 1.2 2000/05/01 20:21:29 peter Exp $ + */ + +/* Messages (1 byte) */ /* I/T (M)andatory or (O)ptional */ +#define MSG_CMDCOMPLETE 0x00 /* M/M */ +#define MSG_TASK_COMPLETE 0x00 /* M/M */ /* SPI3 Terminology */ +#define MSG_EXTENDED 0x01 /* O/O */ +#define MSG_SAVEDATAPOINTER 0x02 /* O/O */ +#define MSG_RESTOREPOINTERS 0x03 /* O/O */ +#define MSG_DISCONNECT 0x04 /* O/O */ +#define MSG_INITIATOR_DET_ERR 0x05 /* M/M */ +#define MSG_ABORT 0x06 /* O/M */ +#define MSG_ABORT_TASK_SET 0x06 /* O/M */ /* SPI3 Terminology */ +#define MSG_MESSAGE_REJECT 0x07 /* M/M */ +#define MSG_NOOP 0x08 /* M/M */ +#define MSG_PARITY_ERROR 0x09 /* M/M */ +#define MSG_LINK_CMD_COMPLETE 0x0a /* O/O */ +#define MSG_LINK_CMD_COMPLETEF 0x0b /* O/O */ +#define MSG_BUS_DEV_RESET 0x0c /* O/M */ +#define MSG_TARGET_RESET 0x0c /* O/M */ /* SPI3 Terminology */ +#define MSG_ABORT_TAG 0x0d /* O/O */ +#define MSG_ABORT_TASK 0x0d /* O/O */ /* SPI3 Terminology */ +#define MSG_CLEAR_QUEUE 0x0e /* O/O */ +#define MSG_CLEAR_TASK_SET 0x0e /* O/O */ /* SPI3 Terminology */ +#define MSG_INIT_RECOVERY 0x0f /* O/O */ /* Deprecated in SPI3 */ +#define MSG_REL_RECOVERY 0x10 /* O/O */ /* Deprecated in SPI3 */ +#define MSG_TERM_IO_PROC 0x11 /* O/O */ /* Deprecated in SPI3 */ +#define MSG_CLEAR_ACA 0x16 /* O/O */ /* SPI3 */ +#define MSG_LOGICAL_UNIT_RESET 0x17 /* O/O */ /* SPI3 */ +#define MSG_QAS_REQUEST 0x55 /* O/O */ /* SPI3 */ + +/* Messages (2 byte) */ +#define MSG_SIMPLE_Q_TAG 0x20 /* O/O */ +#define MSG_SIMPLE_TASK 0x20 /* O/O */ /* SPI3 Terminology */ +#define MSG_HEAD_OF_Q_TAG 0x21 /* O/O */ +#define MSG_HEAD_OF_QUEUE_TASK 0x21 /* O/O */ /* SPI3 Terminology */ +#define MSG_ORDERED_Q_TAG 0x22 /* O/O */ +#define MSG_ORDERED_TASK 0x22 /* O/O */ /* SPI3 Terminology */ +#define MSG_IGN_WIDE_RESIDUE 0x23 /* O/O */ +#define MSG_ACA_TASK 0x24 /* 0/0 */ /* SPI3 */ + +/* Identify message */ /* M/M */ +#define MSG_IDENTIFYFLAG 0x80 +#define MSG_IDENTIFY_DISCFLAG 0x40 +#define MSG_IDENTIFY(lun, disc) (((disc) ? 0xc0 : MSG_IDENTIFYFLAG) | (lun)) +#define MSG_ISIDENTIFY(m) ((m) & MSG_IDENTIFYFLAG) +#define MSG_IDENTIFY_LUNMASK 0x3F + +/* Extended messages (opcode and length) */ +#define MSG_EXT_SDTR 0x01 +#define MSG_EXT_SDTR_LEN 0x03 + +#define MSG_EXT_WDTR 0x03 +#define MSG_EXT_WDTR_LEN 0x02 +#define MSG_EXT_WDTR_BUS_8_BIT 0x00 +#define MSG_EXT_WDTR_BUS_16_BIT 0x01 +#define MSG_EXT_WDTR_BUS_32_BIT 0x02 /* Deprecated in SPI3 */ + +#define MSG_EXT_PPR 0x04 /* SPI3 */ +#define MSG_EXT_PPR_LEN 0x06 +#define MSG_EXT_PPR_PCOMP_EN 0x80 +#define MSG_EXT_PPR_RTI 0x40 +#define MSG_EXT_PPR_RD_STRM 0x20 +#define MSG_EXT_PPR_WR_FLOW 0x10 +#define MSG_EXT_PPR_HOLD_MCS 0x08 +#define MSG_EXT_PPR_QAS_REQ 0x04 +#define MSG_EXT_PPR_DT_REQ 0x02 +#define MSG_EXT_PPR_IU_REQ 0x01 |