diff options
Diffstat (limited to 'drivers/spi/spi-meson-spifc.c')
| -rw-r--r-- | drivers/spi/spi-meson-spifc.c | 457 |
1 files changed, 457 insertions, 0 deletions
diff --git a/drivers/spi/spi-meson-spifc.c b/drivers/spi/spi-meson-spifc.c new file mode 100644 index 000000000..c8ed7815c --- /dev/null +++ b/drivers/spi/spi-meson-spifc.c @@ -0,0 +1,457 @@ +// SPDX-License-Identifier: GPL-2.0+ +// +// Driver for Amlogic Meson SPI flash controller (SPIFC) +// +// Copyright (C) 2014 Beniamino Galvani <b.galvani@gmail.com> +// + +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/pm_runtime.h> +#include <linux/regmap.h> +#include <linux/spi/spi.h> +#include <linux/types.h> + +/* register map */ +#define REG_CMD 0x00 +#define REG_ADDR 0x04 +#define REG_CTRL 0x08 +#define REG_CTRL1 0x0c +#define REG_STATUS 0x10 +#define REG_CTRL2 0x14 +#define REG_CLOCK 0x18 +#define REG_USER 0x1c +#define REG_USER1 0x20 +#define REG_USER2 0x24 +#define REG_USER3 0x28 +#define REG_USER4 0x2c +#define REG_SLAVE 0x30 +#define REG_SLAVE1 0x34 +#define REG_SLAVE2 0x38 +#define REG_SLAVE3 0x3c +#define REG_C0 0x40 +#define REG_B8 0x60 +#define REG_MAX 0x7c + +/* register fields */ +#define CMD_USER BIT(18) +#define CTRL_ENABLE_AHB BIT(17) +#define CLOCK_SOURCE BIT(31) +#define CLOCK_DIV_SHIFT 12 +#define CLOCK_DIV_MASK (0x3f << CLOCK_DIV_SHIFT) +#define CLOCK_CNT_HIGH_SHIFT 6 +#define CLOCK_CNT_HIGH_MASK (0x3f << CLOCK_CNT_HIGH_SHIFT) +#define CLOCK_CNT_LOW_SHIFT 0 +#define CLOCK_CNT_LOW_MASK (0x3f << CLOCK_CNT_LOW_SHIFT) +#define USER_DIN_EN_MS BIT(0) +#define USER_CMP_MODE BIT(2) +#define USER_UC_DOUT_SEL BIT(27) +#define USER_UC_DIN_SEL BIT(28) +#define USER_UC_MASK ((BIT(5) - 1) << 27) +#define USER1_BN_UC_DOUT_SHIFT 17 +#define USER1_BN_UC_DOUT_MASK (0xff << 16) +#define USER1_BN_UC_DIN_SHIFT 8 +#define USER1_BN_UC_DIN_MASK (0xff << 8) +#define USER4_CS_ACT BIT(30) +#define SLAVE_TRST_DONE BIT(4) +#define SLAVE_OP_MODE BIT(30) +#define SLAVE_SW_RST BIT(31) + +#define SPIFC_BUFFER_SIZE 64 + +/** + * struct meson_spifc + * @master: the SPI master + * @regmap: regmap for device registers + * @clk: input clock of the built-in baud rate generator + * @dev: the device structure + */ +struct meson_spifc { + struct spi_master *master; + struct regmap *regmap; + struct clk *clk; + struct device *dev; +}; + +static const struct regmap_config spifc_regmap_config = { + .reg_bits = 32, + .val_bits = 32, + .reg_stride = 4, + .max_register = REG_MAX, +}; + +/** + * meson_spifc_wait_ready() - wait for the current operation to terminate + * @spifc: the Meson SPI device + * Return: 0 on success, a negative value on error + */ +static int meson_spifc_wait_ready(struct meson_spifc *spifc) +{ + unsigned long deadline = jiffies + msecs_to_jiffies(5); + u32 data; + + do { + regmap_read(spifc->regmap, REG_SLAVE, &data); + if (data & SLAVE_TRST_DONE) + return 0; + cond_resched(); + } while (!time_after(jiffies, deadline)); + + return -ETIMEDOUT; +} + +/** + * meson_spifc_drain_buffer() - copy data from device buffer to memory + * @spifc: the Meson SPI device + * @buf: the destination buffer + * @len: number of bytes to copy + */ +static void meson_spifc_drain_buffer(struct meson_spifc *spifc, u8 *buf, + int len) +{ + u32 data; + int i = 0; + + while (i < len) { + regmap_read(spifc->regmap, REG_C0 + i, &data); + + if (len - i >= 4) { + *((u32 *)buf) = data; + buf += 4; + } else { + memcpy(buf, &data, len - i); + break; + } + i += 4; + } +} + +/** + * meson_spifc_fill_buffer() - copy data from memory to device buffer + * @spifc: the Meson SPI device + * @buf: the source buffer + * @len: number of bytes to copy + */ +static void meson_spifc_fill_buffer(struct meson_spifc *spifc, const u8 *buf, + int len) +{ + u32 data; + int i = 0; + + while (i < len) { + if (len - i >= 4) + data = *(u32 *)buf; + else + memcpy(&data, buf, len - i); + + regmap_write(spifc->regmap, REG_C0 + i, data); + + buf += 4; + i += 4; + } +} + +/** + * meson_spifc_setup_speed() - program the clock divider + * @spifc: the Meson SPI device + * @speed: desired speed in Hz + */ +static void meson_spifc_setup_speed(struct meson_spifc *spifc, u32 speed) +{ + unsigned long parent, value; + int n; + + parent = clk_get_rate(spifc->clk); + n = max_t(int, parent / speed - 1, 1); + + dev_dbg(spifc->dev, "parent %lu, speed %u, n %d\n", parent, + speed, n); + + value = (n << CLOCK_DIV_SHIFT) & CLOCK_DIV_MASK; + value |= (n << CLOCK_CNT_LOW_SHIFT) & CLOCK_CNT_LOW_MASK; + value |= (((n + 1) / 2 - 1) << CLOCK_CNT_HIGH_SHIFT) & + CLOCK_CNT_HIGH_MASK; + + regmap_write(spifc->regmap, REG_CLOCK, value); +} + +/** + * meson_spifc_txrx() - transfer a chunk of data + * @spifc: the Meson SPI device + * @xfer: the current SPI transfer + * @offset: offset of the data to transfer + * @len: length of the data to transfer + * @last_xfer: whether this is the last transfer of the message + * @last_chunk: whether this is the last chunk of the transfer + * Return: 0 on success, a negative value on error + */ +static int meson_spifc_txrx(struct meson_spifc *spifc, + struct spi_transfer *xfer, + int offset, int len, bool last_xfer, + bool last_chunk) +{ + bool keep_cs = true; + int ret; + + if (xfer->tx_buf) + meson_spifc_fill_buffer(spifc, xfer->tx_buf + offset, len); + + /* enable DOUT stage */ + regmap_update_bits(spifc->regmap, REG_USER, USER_UC_MASK, + USER_UC_DOUT_SEL); + regmap_write(spifc->regmap, REG_USER1, + (8 * len - 1) << USER1_BN_UC_DOUT_SHIFT); + + /* enable data input during DOUT */ + regmap_update_bits(spifc->regmap, REG_USER, USER_DIN_EN_MS, + USER_DIN_EN_MS); + + if (last_chunk) { + if (last_xfer) + keep_cs = xfer->cs_change; + else + keep_cs = !xfer->cs_change; + } + + regmap_update_bits(spifc->regmap, REG_USER4, USER4_CS_ACT, + keep_cs ? USER4_CS_ACT : 0); + + /* clear transition done bit */ + regmap_update_bits(spifc->regmap, REG_SLAVE, SLAVE_TRST_DONE, 0); + /* start transfer */ + regmap_update_bits(spifc->regmap, REG_CMD, CMD_USER, CMD_USER); + + ret = meson_spifc_wait_ready(spifc); + + if (!ret && xfer->rx_buf) + meson_spifc_drain_buffer(spifc, xfer->rx_buf + offset, len); + + return ret; +} + +/** + * meson_spifc_transfer_one() - perform a single transfer + * @master: the SPI master + * @spi: the SPI device + * @xfer: the current SPI transfer + * Return: 0 on success, a negative value on error + */ +static int meson_spifc_transfer_one(struct spi_master *master, + struct spi_device *spi, + struct spi_transfer *xfer) +{ + struct meson_spifc *spifc = spi_master_get_devdata(master); + int len, done = 0, ret = 0; + + meson_spifc_setup_speed(spifc, xfer->speed_hz); + + regmap_update_bits(spifc->regmap, REG_CTRL, CTRL_ENABLE_AHB, 0); + + while (done < xfer->len && !ret) { + len = min_t(int, xfer->len - done, SPIFC_BUFFER_SIZE); + ret = meson_spifc_txrx(spifc, xfer, done, len, + spi_transfer_is_last(master, xfer), + done + len >= xfer->len); + done += len; + } + + regmap_update_bits(spifc->regmap, REG_CTRL, CTRL_ENABLE_AHB, + CTRL_ENABLE_AHB); + + return ret; +} + +/** + * meson_spifc_hw_init() - reset and initialize the SPI controller + * @spifc: the Meson SPI device + */ +static void meson_spifc_hw_init(struct meson_spifc *spifc) +{ + /* reset device */ + regmap_update_bits(spifc->regmap, REG_SLAVE, SLAVE_SW_RST, + SLAVE_SW_RST); + /* disable compatible mode */ + regmap_update_bits(spifc->regmap, REG_USER, USER_CMP_MODE, 0); + /* set master mode */ + regmap_update_bits(spifc->regmap, REG_SLAVE, SLAVE_OP_MODE, 0); +} + +static int meson_spifc_probe(struct platform_device *pdev) +{ + struct spi_master *master; + struct meson_spifc *spifc; + void __iomem *base; + unsigned int rate; + int ret = 0; + + master = spi_alloc_master(&pdev->dev, sizeof(struct meson_spifc)); + if (!master) + return -ENOMEM; + + platform_set_drvdata(pdev, master); + + spifc = spi_master_get_devdata(master); + spifc->dev = &pdev->dev; + + base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(base)) { + ret = PTR_ERR(base); + goto out_err; + } + + spifc->regmap = devm_regmap_init_mmio(spifc->dev, base, + &spifc_regmap_config); + if (IS_ERR(spifc->regmap)) { + ret = PTR_ERR(spifc->regmap); + goto out_err; + } + + spifc->clk = devm_clk_get(spifc->dev, NULL); + if (IS_ERR(spifc->clk)) { + dev_err(spifc->dev, "missing clock\n"); + ret = PTR_ERR(spifc->clk); + goto out_err; + } + + ret = clk_prepare_enable(spifc->clk); + if (ret) { + dev_err(spifc->dev, "can't prepare clock\n"); + goto out_err; + } + + rate = clk_get_rate(spifc->clk); + + master->num_chipselect = 1; + master->dev.of_node = pdev->dev.of_node; + master->bits_per_word_mask = SPI_BPW_MASK(8); + master->auto_runtime_pm = true; + master->transfer_one = meson_spifc_transfer_one; + master->min_speed_hz = rate >> 6; + master->max_speed_hz = rate >> 1; + + meson_spifc_hw_init(spifc); + + pm_runtime_set_active(spifc->dev); + pm_runtime_enable(spifc->dev); + + ret = devm_spi_register_master(spifc->dev, master); + if (ret) { + dev_err(spifc->dev, "failed to register spi master\n"); + goto out_clk; + } + + return 0; +out_clk: + clk_disable_unprepare(spifc->clk); + pm_runtime_disable(spifc->dev); +out_err: + spi_master_put(master); + return ret; +} + +static int meson_spifc_remove(struct platform_device *pdev) +{ + struct spi_master *master = platform_get_drvdata(pdev); + struct meson_spifc *spifc = spi_master_get_devdata(master); + + pm_runtime_get_sync(&pdev->dev); + clk_disable_unprepare(spifc->clk); + pm_runtime_disable(&pdev->dev); + + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int meson_spifc_suspend(struct device *dev) +{ + struct spi_master *master = dev_get_drvdata(dev); + struct meson_spifc *spifc = spi_master_get_devdata(master); + int ret; + + ret = spi_master_suspend(master); + if (ret) + return ret; + + if (!pm_runtime_suspended(dev)) + clk_disable_unprepare(spifc->clk); + + return 0; +} + +static int meson_spifc_resume(struct device *dev) +{ + struct spi_master *master = dev_get_drvdata(dev); + struct meson_spifc *spifc = spi_master_get_devdata(master); + int ret; + + if (!pm_runtime_suspended(dev)) { + ret = clk_prepare_enable(spifc->clk); + if (ret) + return ret; + } + + meson_spifc_hw_init(spifc); + + ret = spi_master_resume(master); + if (ret) + clk_disable_unprepare(spifc->clk); + + return ret; +} +#endif /* CONFIG_PM_SLEEP */ + +#ifdef CONFIG_PM +static int meson_spifc_runtime_suspend(struct device *dev) +{ + struct spi_master *master = dev_get_drvdata(dev); + struct meson_spifc *spifc = spi_master_get_devdata(master); + + clk_disable_unprepare(spifc->clk); + + return 0; +} + +static int meson_spifc_runtime_resume(struct device *dev) +{ + struct spi_master *master = dev_get_drvdata(dev); + struct meson_spifc *spifc = spi_master_get_devdata(master); + + return clk_prepare_enable(spifc->clk); +} +#endif /* CONFIG_PM */ + +static const struct dev_pm_ops meson_spifc_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(meson_spifc_suspend, meson_spifc_resume) + SET_RUNTIME_PM_OPS(meson_spifc_runtime_suspend, + meson_spifc_runtime_resume, + NULL) +}; + +static const struct of_device_id meson_spifc_dt_match[] = { + { .compatible = "amlogic,meson6-spifc", }, + { .compatible = "amlogic,meson-gxbb-spifc", }, + { }, +}; +MODULE_DEVICE_TABLE(of, meson_spifc_dt_match); + +static struct platform_driver meson_spifc_driver = { + .probe = meson_spifc_probe, + .remove = meson_spifc_remove, + .driver = { + .name = "meson-spifc", + .of_match_table = of_match_ptr(meson_spifc_dt_match), + .pm = &meson_spifc_pm_ops, + }, +}; + +module_platform_driver(meson_spifc_driver); + +MODULE_AUTHOR("Beniamino Galvani <b.galvani@gmail.com>"); +MODULE_DESCRIPTION("Amlogic Meson SPIFC driver"); +MODULE_LICENSE("GPL v2"); |