diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/tty/serial/8250/8250_bcm2835aux.c | 212 |
1 files changed, 212 insertions, 0 deletions
diff --git a/drivers/tty/serial/8250/8250_bcm2835aux.c b/drivers/tty/serial/8250/8250_bcm2835aux.c new file mode 100644 index 000000000..fd95860cd --- /dev/null +++ b/drivers/tty/serial/8250/8250_bcm2835aux.c @@ -0,0 +1,212 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Serial port driver for BCM2835AUX UART + * + * Copyright (C) 2016 Martin Sperl <kernel@martin.sperl.org> + * + * Based on 8250_lpc18xx.c: + * Copyright (C) 2015 Joachim Eastwood <manabian@gmail.com> + * + * The bcm2835aux is capable of RTS auto flow-control, but this driver doesn't + * take advantage of it yet. When adding support, be sure not to enable it + * simultaneously to rs485. + */ + +#include <linux/clk.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> + +#include "8250.h" + +#define BCM2835_AUX_UART_CNTL 8 +#define BCM2835_AUX_UART_CNTL_RXEN 0x01 /* Receiver enable */ +#define BCM2835_AUX_UART_CNTL_TXEN 0x02 /* Transmitter enable */ +#define BCM2835_AUX_UART_CNTL_AUTORTS 0x04 /* RTS set by RX fill level */ +#define BCM2835_AUX_UART_CNTL_AUTOCTS 0x08 /* CTS stops transmitter */ +#define BCM2835_AUX_UART_CNTL_RTS3 0x00 /* RTS set until 3 chars left */ +#define BCM2835_AUX_UART_CNTL_RTS2 0x10 /* RTS set until 2 chars left */ +#define BCM2835_AUX_UART_CNTL_RTS1 0x20 /* RTS set until 1 chars left */ +#define BCM2835_AUX_UART_CNTL_RTS4 0x30 /* RTS set until 4 chars left */ +#define BCM2835_AUX_UART_CNTL_RTSINV 0x40 /* Invert auto RTS polarity */ +#define BCM2835_AUX_UART_CNTL_CTSINV 0x80 /* Invert auto CTS polarity */ + +/** + * struct bcm2835aux_data - driver private data of BCM2835 auxiliary UART + * @clk: clock producer of the port's uartclk + * @line: index of the port's serial8250_ports[] entry + * @cntl: cached copy of CNTL register + */ +struct bcm2835aux_data { + struct clk *clk; + int line; + u32 cntl; +}; + +static void bcm2835aux_rs485_start_tx(struct uart_8250_port *up) +{ + if (!(up->port.rs485.flags & SER_RS485_RX_DURING_TX)) { + struct bcm2835aux_data *data = dev_get_drvdata(up->port.dev); + + data->cntl &= ~BCM2835_AUX_UART_CNTL_RXEN; + serial_out(up, BCM2835_AUX_UART_CNTL, data->cntl); + } + + /* + * On the bcm2835aux, the MCR register contains no other + * flags besides RTS. So no need for a read-modify-write. + */ + if (up->port.rs485.flags & SER_RS485_RTS_ON_SEND) + serial8250_out_MCR(up, 0); + else + serial8250_out_MCR(up, UART_MCR_RTS); +} + +static void bcm2835aux_rs485_stop_tx(struct uart_8250_port *up) +{ + if (up->port.rs485.flags & SER_RS485_RTS_AFTER_SEND) + serial8250_out_MCR(up, 0); + else + serial8250_out_MCR(up, UART_MCR_RTS); + + if (!(up->port.rs485.flags & SER_RS485_RX_DURING_TX)) { + struct bcm2835aux_data *data = dev_get_drvdata(up->port.dev); + + data->cntl |= BCM2835_AUX_UART_CNTL_RXEN; + serial_out(up, BCM2835_AUX_UART_CNTL, data->cntl); + } +} + +static int bcm2835aux_serial_probe(struct platform_device *pdev) +{ + struct uart_8250_port up = { }; + struct bcm2835aux_data *data; + struct resource *res; + int ret; + + /* allocate the custom structure */ + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); + if (!data) + return -ENOMEM; + + /* initialize data */ + up.capabilities = UART_CAP_FIFO | UART_CAP_MINI; + up.port.dev = &pdev->dev; + up.port.regshift = 2; + up.port.type = PORT_16550; + up.port.iotype = UPIO_MEM; + up.port.fifosize = 8; + up.port.flags = UPF_SHARE_IRQ | UPF_FIXED_PORT | UPF_FIXED_TYPE | + UPF_SKIP_TEST | UPF_IOREMAP; + up.port.rs485_config = serial8250_em485_config; + up.rs485_start_tx = bcm2835aux_rs485_start_tx; + up.rs485_stop_tx = bcm2835aux_rs485_stop_tx; + + /* initialize cached copy with power-on reset value */ + data->cntl = BCM2835_AUX_UART_CNTL_RXEN | BCM2835_AUX_UART_CNTL_TXEN; + + platform_set_drvdata(pdev, data); + + /* get the clock - this also enables the HW */ + data->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(data->clk)) + return dev_err_probe(&pdev->dev, PTR_ERR(data->clk), "could not get clk\n"); + + /* get the interrupt */ + ret = platform_get_irq(pdev, 0); + if (ret < 0) + return ret; + up.port.irq = ret; + + /* map the main registers */ + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "memory resource not found"); + return -EINVAL; + } + up.port.mapbase = res->start; + up.port.mapsize = resource_size(res); + + /* Check for a fixed line number */ + ret = of_alias_get_id(pdev->dev.of_node, "serial"); + if (ret >= 0) + up.port.line = ret; + + /* enable the clock as a last step */ + ret = clk_prepare_enable(data->clk); + if (ret) { + dev_err(&pdev->dev, "unable to enable uart clock - %d\n", + ret); + return ret; + } + + /* the HW-clock divider for bcm2835aux is 8, + * but 8250 expects a divider of 16, + * so we have to multiply the actual clock by 2 + * to get identical baudrates. + */ + up.port.uartclk = clk_get_rate(data->clk) * 2; + + /* register the port */ + ret = serial8250_register_8250_port(&up); + if (ret < 0) { + dev_err_probe(&pdev->dev, ret, "unable to register 8250 port\n"); + goto dis_clk; + } + data->line = ret; + + return 0; + +dis_clk: + clk_disable_unprepare(data->clk); + return ret; +} + +static int bcm2835aux_serial_remove(struct platform_device *pdev) +{ + struct bcm2835aux_data *data = platform_get_drvdata(pdev); + + serial8250_unregister_port(data->line); + clk_disable_unprepare(data->clk); + + return 0; +} + +static const struct of_device_id bcm2835aux_serial_match[] = { + { .compatible = "brcm,bcm2835-aux-uart" }, + { }, +}; +MODULE_DEVICE_TABLE(of, bcm2835aux_serial_match); + +static struct platform_driver bcm2835aux_serial_driver = { + .driver = { + .name = "bcm2835-aux-uart", + .of_match_table = bcm2835aux_serial_match, + }, + .probe = bcm2835aux_serial_probe, + .remove = bcm2835aux_serial_remove, +}; +module_platform_driver(bcm2835aux_serial_driver); + +#ifdef CONFIG_SERIAL_8250_CONSOLE + +static int __init early_bcm2835aux_setup(struct earlycon_device *device, + const char *options) +{ + if (!device->port.membase) + return -ENODEV; + + device->port.iotype = UPIO_MEM32; + device->port.regshift = 2; + + return early_serial8250_setup(device, NULL); +} + +OF_EARLYCON_DECLARE(bcm2835aux, "brcm,bcm2835-aux-uart", + early_bcm2835aux_setup); +#endif + +MODULE_DESCRIPTION("BCM2835 auxiliar UART driver"); +MODULE_AUTHOR("Martin Sperl <kernel@martin.sperl.org>"); +MODULE_LICENSE("GPL v2"); |