From 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sat, 27 Apr 2024 12:05:51 +0200 Subject: Adding upstream version 5.10.209. Signed-off-by: Daniel Baumann --- .../devicetree/bindings/spi/spi-controller.yaml | 174 +++++++++++++++++++++ 1 file changed, 174 insertions(+) create mode 100644 Documentation/devicetree/bindings/spi/spi-controller.yaml (limited to 'Documentation/devicetree/bindings/spi/spi-controller.yaml') diff --git a/Documentation/devicetree/bindings/spi/spi-controller.yaml b/Documentation/devicetree/bindings/spi/spi-controller.yaml new file mode 100644 index 000000000..1b56d5e40 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-controller.yaml @@ -0,0 +1,174 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/spi-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SPI Controller Generic Binding + +maintainers: + - Mark Brown + +description: | + SPI busses can be described with a node for the SPI controller device + and a set of child nodes for each SPI slave on the bus. The system SPI + controller may be described for use in SPI master mode or in SPI slave mode, + but not for both at the same time. + +properties: + $nodename: + pattern: "^spi(@.*|-[0-9a-f])*$" + + "#address-cells": + enum: [0, 1] + + "#size-cells": + const: 0 + + cs-gpios: + description: | + GPIOs used as chip selects. + If that property is used, the number of chip selects will be + increased automatically with max(cs-gpios, hardware chip selects). + + So if, for example, the controller has 4 CS lines, and the + cs-gpios looks like this + cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>; + + Then it should be configured so that num_chipselect = 4, with + the following mapping + cs0 : &gpio1 0 0 + cs1 : native + cs2 : &gpio1 1 0 + cs3 : &gpio1 2 0 + + num-cs: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Total number of chip selects. + + spi-slave: + $ref: /schemas/types.yaml#/definitions/flag + description: + The SPI controller acts as a slave, instead of a master. + +allOf: + - if: + not: + required: + - spi-slave + then: + properties: + "#address-cells": + const: 1 + else: + properties: + "#address-cells": + const: 0 + +patternProperties: + "^slave$": + type: object + + properties: + compatible: + description: + Compatible of the SPI device. + + required: + - compatible + + "^.*@[0-9a-f]+$": + type: object + + properties: + compatible: + description: + Compatible of the SPI device. + + reg: + minimum: 0 + maximum: 256 + description: + Chip select used by the device. + + spi-3wire: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires 3-wire mode. + + spi-cpha: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires shifted clock phase (CPHA) mode. + + spi-cpol: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires inverse clock polarity (CPOL) mode. + + spi-cs-high: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires the chip select active high. + + spi-lsb-first: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires the LSB first mode. + + spi-max-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Maximum SPI clocking speed of the device in Hz. + + spi-rx-bus-width: + description: + Bus width to the SPI bus used for read transfers. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2, 4, 8] + default: 1 + + spi-rx-delay-us: + description: + Delay, in microseconds, after a read transfer. + + spi-tx-bus-width: + description: + Bus width to the SPI bus used for write transfers. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2, 4, 8] + default: 1 + + spi-tx-delay-us: + description: + Delay, in microseconds, after a write transfer. + + required: + - compatible + - reg + +additionalProperties: true + +examples: + - | + spi@f00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; + reg = <0xf00 0x20>; + interrupts = <2 13 0 2 14 0>; + interrupt-parent = <&mpc5200_pic>; + + ethernet-switch@0 { + compatible = "micrel,ks8995m"; + spi-max-frequency = <1000000>; + reg = <0>; + }; + + codec@1 { + compatible = "ti,tlv320aic26"; + spi-max-frequency = <100000>; + reg = <1>; + }; + }; -- cgit v1.2.3