// SPDX-License-Identifier: GPL-2.0-only /* * drivers/mmc/host/sdhci-msm.c - Qualcomm SDHCI Platform driver * * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved. */ #include #include #include #include #include #include #include #include #include #include #include #include #include "sdhci-pltfm.h" #include "cqhci.h" #define CORE_MCI_VERSION 0x50 #define CORE_VERSION_MAJOR_SHIFT 28 #define CORE_VERSION_MAJOR_MASK (0xf << CORE_VERSION_MAJOR_SHIFT) #define CORE_VERSION_MINOR_MASK 0xff #define CORE_MCI_GENERICS 0x70 #define SWITCHABLE_SIGNALING_VOLTAGE BIT(29) #define HC_MODE_EN 0x1 #define CORE_POWER 0x0 #define CORE_SW_RST BIT(7) #define FF_CLK_SW_RST_DIS BIT(13) #define CORE_PWRCTL_BUS_OFF BIT(0) #define CORE_PWRCTL_BUS_ON BIT(1) #define CORE_PWRCTL_IO_LOW BIT(2) #define CORE_PWRCTL_IO_HIGH BIT(3) #define CORE_PWRCTL_BUS_SUCCESS BIT(0) #define CORE_PWRCTL_BUS_FAIL BIT(1) #define CORE_PWRCTL_IO_SUCCESS BIT(2) #define CORE_PWRCTL_IO_FAIL BIT(3) #define REQ_BUS_OFF BIT(0) #define REQ_BUS_ON BIT(1) #define REQ_IO_LOW BIT(2) #define REQ_IO_HIGH BIT(3) #define INT_MASK 0xf #define MAX_PHASES 16 #define CORE_DLL_LOCK BIT(7) #define CORE_DDR_DLL_LOCK BIT(11) #define CORE_DLL_EN BIT(16) #define CORE_CDR_EN BIT(17) #define CORE_CK_OUT_EN BIT(18) #define CORE_CDR_EXT_EN BIT(19) #define CORE_DLL_PDN BIT(29) #define CORE_DLL_RST BIT(30) #define CORE_CMD_DAT_TRACK_SEL BIT(0) #define CORE_DDR_CAL_EN BIT(0) #define CORE_FLL_CYCLE_CNT BIT(18) #define CORE_DLL_CLOCK_DISABLE BIT(21) #define DLL_USR_CTL_POR_VAL 0x10800 #define ENABLE_DLL_LOCK_STATUS BIT(26) #define FINE_TUNE_MODE_EN BIT(27) #define BIAS_OK_SIGNAL BIT(29) #define DLL_CONFIG_3_LOW_FREQ_VAL 0x08 #define DLL_CONFIG_3_HIGH_FREQ_VAL 0x10 #define CORE_VENDOR_SPEC_POR_VAL 0xa9c #define CORE_CLK_PWRSAVE BIT(1) #define CORE_HC_MCLK_SEL_DFLT (2 << 8) #define CORE_HC_MCLK_SEL_HS400 (3 << 8) #define CORE_HC_MCLK_SEL_MASK (3 << 8) #define CORE_IO_PAD_PWR_SWITCH_EN BIT(15) #define CORE_IO_PAD_PWR_SWITCH BIT(16) #define CORE_HC_SELECT_IN_EN BIT(18) #define CORE_HC_SELECT_IN_HS400 (6 << 19) #define CORE_HC_SELECT_IN_MASK (7 << 19) #define CORE_3_0V_SUPPORT BIT(25) #define CORE_1_8V_SUPPORT BIT(26) #define CORE_VOLT_SUPPORT (CORE_3_0V_SUPPORT | CORE_1_8V_SUPPORT) #define CORE_CSR_CDC_CTLR_CFG0 0x130 #define CORE_SW_TRIG_FULL_CALIB BIT(16) #define CORE_HW_AUTOCAL_ENA BIT(17) #define CORE_CSR_CDC_CTLR_CFG1 0x134 #define CORE_CSR_CDC_CAL_TIMER_CFG0 0x138 #define CORE_TIMER_ENA BIT(16) #define CORE_CSR_CDC_CAL_TIMER_CFG1 0x13C #define CORE_CSR_CDC_REFCOUNT_CFG 0x140 #define CORE_CSR_CDC_COARSE_CAL_CFG 0x144 #define CORE_CDC_OFFSET_CFG 0x14C #define CORE_CSR_CDC_DELAY_CFG 0x150 #define CORE_CDC_SLAVE_DDA_CFG 0x160 #define CORE_CSR_CDC_STATUS0 0x164 #define CORE_CALIBRATION_DONE BIT(0) #define CORE_CDC_ERROR_CODE_MASK 0x7000000 #define CORE_CSR_CDC_GEN_CFG 0x178 #define CORE_CDC_SWITCH_BYPASS_OFF BIT(0) #define CORE_CDC_SWITCH_RC_EN BIT(1) #define CORE_CDC_T4_DLY_SEL BIT(0) #define CORE_CMDIN_RCLK_EN BIT(1) #define CORE_START_CDC_TRAFFIC BIT(6) #define CORE_PWRSAVE_DLL BIT(3) #define DDR_CONFIG_POR_VAL 0x80040873 #define INVALID_TUNING_PHASE -1 #define SDHCI_MSM_MIN_CLOCK 400000 #define CORE_FREQ_100MHZ (100 * 1000 * 1000) #define CDR_SELEXT_SHIFT 20 #define CDR_SELEXT_MASK (0xf << CDR_SELEXT_SHIFT) #define CMUX_SHIFT_PHASE_SHIFT 24 #define CMUX_SHIFT_PHASE_MASK (7 << CMUX_SHIFT_PHASE_SHIFT) #define MSM_MMC_AUTOSUSPEND_DELAY_MS 50 /* Timeout value to avoid infinite waiting for pwr_irq */ #define MSM_PWR_IRQ_TIMEOUT_MS 5000 /* Max load for eMMC Vdd-io supply */ #define MMC_VQMMC_MAX_LOAD_UA 325000 #define msm_host_readl(msm_host, host, offset) \ msm_host->var_ops->msm_readl_relaxed(host, offset) #define msm_host_writel(msm_host, val, host, offset) \ msm_host->var_ops->msm_writel_relaxed(val, host, offset) /* CQHCI vendor specific registers */ #define CQHCI_VENDOR_CFG1 0xA00 #define CQHCI_VENDOR_DIS_RST_ON_CQ_EN (0x3 << 13) struct sdhci_msm_offset { u32 core_hc_mode; u32 core_mci_data_cnt; u32 core_mci_status; u32 core_mci_fifo_cnt; u32 core_mci_version; u32 core_generics; u32 core_testbus_config; u32 core_testbus_sel2_bit; u32 core_testbus_ena; u32 core_testbus_sel2; u32 core_pwrctl_status; u32 core_pwrctl_mask; u32 core_pwrctl_clear; u32 core_pwrctl_ctl; u32 core_sdcc_debug_reg; u32 core_dll_config; u32 core_dll_status; u32 core_vendor_spec; u32 core_vendor_spec_adma_err_addr0; u32 core_vendor_spec_adma_err_addr1; u32 core_vendor_spec_func2; u32 core_vendor_spec_capabilities0; u32 core_ddr_200_cfg; u32 core_vendor_spec3; u32 core_dll_config_2; u32 core_dll_config_3; u32 core_ddr_config_old; /* Applicable to sdcc minor ver < 0x49 */ u32 core_ddr_config; u32 core_dll_usr_ctl; /* Present on SDCC5.1 onwards */ }; static const struct sdhci_msm_offset sdhci_msm_v5_offset = { .core_mci_data_cnt = 0x35c, .core_mci_status = 0x324, .core_mci_fifo_cnt = 0x308, .core_mci_version = 0x318, .core_generics = 0x320, .core_testbus_config = 0x32c, .core_testbus_sel2_bit = 3, .core_testbus_ena = (1 << 31), .core_testbus_sel2 = (1 << 3), .core_pwrctl_status = 0x240, .core_pwrctl_mask = 0x244, .core_pwrctl_clear = 0x248, .core_pwrctl_ctl = 0x24c, .core_sdcc_debug_reg = 0x358, .core_dll_config = 0x200, .core_dll_status = 0x208, .core_vendor_spec = 0x20c, .core_vendor_spec_adma_err_addr0 = 0x214, .core_vendor_spec_adma_err_addr1 = 0x218, .core_vendor_spec_func2 = 0x210, .core_vendor_spec_capabilities0 = 0x21c, .core_ddr_200_cfg = 0x224, .core_vendor_spec3 = 0x250, .core_dll_config_2 = 0x254, .core_dll_config_3 = 0x258, .core_ddr_config = 0x25c, .core_dll_usr_ctl = 0x388, }; static const struct sdhci_msm_offset sdhci_msm_mci_offset = { .core_hc_mode = 0x78, .core_mci_data_cnt = 0x30, .core_mci_status = 0x34, .core_mci_fifo_cnt = 0x44, .core_mci_version = 0x050, .core_generics = 0x70, .core_testbus_config = 0x0cc, .core_testbus_sel2_bit = 4, .core_testbus_ena = (1 << 3), .core_testbus_sel2 = (1 << 4), .core_pwrctl_status = 0xdc, .core_pwrctl_mask = 0xe0, .core_pwrctl_clear = 0xe4, .core_pwrctl_ctl = 0xe8, .core_sdcc_debug_reg = 0x124, .core_dll_config = 0x100, .core_dll_status = 0x108, .core_vendor_spec = 0x10c, .core_vendor_spec_adma_err_addr0 = 0x114, .core_vendor_spec_adma_err_addr1 = 0x118, .core_vendor_spec_func2 = 0x110, .core_vendor_spec_capabilities0 = 0x11c, .core_ddr_200_cfg = 0x184, .core_vendor_spec3 = 0x1b0, .core_dll_config_2 = 0x1b4, .core_ddr_config_old = 0x1b8, .core_ddr_config = 0x1bc, }; struct sdhci_msm_variant_ops { u32 (*msm_readl_relaxed)(struct sdhci_host *host, u32 offset); void (*msm_writel_relaxed)(u32 val, struct sdhci_host *host, u32 offset); }; /* * From V5, register spaces have changed. Wrap this info in a structure * and choose the data_structure based on version info mentioned in DT. */ struct sdhci_msm_variant_info { bool mci_removed; bool restore_dll_config; bool uses_tassadar_dll; const struct sdhci_msm_variant_ops *var_ops; const struct sdhci_msm_offset *offset; }; struct sdhci_msm_host { struct platform_device *pdev; void __iomem *core_mem; /* MSM SDCC mapped address */ int pwr_irq; /* power irq */ struct clk *bus_clk; /* SDHC bus voter clock */ struct clk *xo_clk; /* TCXO clk needed for FLL feature of cm_dll*/ struct clk_bulk_data bulk_clks[4]; /* core, iface, cal, sleep clocks */ unsigned long clk_rate; struct mmc_host *mmc; struct opp_table *opp_table; bool use_14lpp_dll_reset; bool tuning_done; bool calibration_done; u8 saved_tuning_phase; bool use_cdclp533; u32 curr_pwr_state; u32 curr_io_level; wait_queue_head_t pwr_irq_wait; bool pwr_irq_flag; u32 caps_0; bool mci_removed; bool restore_dll_config; const struct sdhci_msm_variant_ops *var_ops; const struct sdhci_msm_offset *offset; bool use_cdr; u32 transfer_mode; bool updated_ddr_cfg; bool uses_tassadar_dll; u32 dll_config; u32 ddr_config; bool vqmmc_enabled; }; static const struct sdhci_msm_offset *sdhci_priv_msm_offset(struct sdhci_host *host) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); return msm_host->offset; } /* * APIs to read/write to vendor specific registers which were there in the * core_mem region before MCI was removed. */ static u32 sdhci_msm_mci_variant_readl_relaxed(struct sdhci_host *host, u32 offset) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); return readl_relaxed(msm_host->core_mem + offset); } static u32 sdhci_msm_v5_variant_readl_relaxed(struct sdhci_host *host, u32 offset) { return readl_relaxed(host->ioaddr + offset); } static void sdhci_msm_mci_variant_writel_relaxed(u32 val, struct sdhci_host *host, u32 offset) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); writel_relaxed(val, msm_host->core_mem + offset); } static void sdhci_msm_v5_variant_writel_relaxed(u32 val, struct sdhci_host *host, u32 offset) { writel_relaxed(val, host->ioaddr + offset); } static unsigned int msm_get_clock_rate_for_bus_mode(struct sdhci_host *host, unsigned int clock) { struct mmc_ios ios = host->mmc->ios; /* * The SDHC requires internal clock frequency to be double the * actual clock that will be set for DDR mode. The controller * uses the faster clock(100/400MHz) for some of its parts and * send the actual required clock (50/200MHz) to the card. */ if (ios.timing == MMC_TIMING_UHS_DDR50 || ios.timing == MMC_TIMING_MMC_DDR52 || ios.timing == MMC_TIMING_MMC_HS400 || host->flags & SDHCI_HS400_TUNING) clock *= 2; return clock; } static void msm_set_clock_rate_for_bus_mode(struct sdhci_host *host, unsigned int clock) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); struct mmc_ios curr_ios = host->mmc->ios; struct clk *core_clk = msm_host->bulk_clks[0].clk; int rc; clock = msm_get_clock_rate_for_bus_mode(host, clock); rc = dev_pm_opp_set_rate(mmc_dev(host->mmc), clock); if (rc) { pr_err("%s: Failed to set clock at rate %u at timing %d\n", mmc_hostname(host->mmc), clock, curr_ios.timing); return; } msm_host->clk_rate = clock; pr_debug("%s: Setting clock at rate %lu at timing %d\n", mmc_hostname(host->mmc), clk_get_rate(core_clk), curr_ios.timing); } /* Platform specific tuning */ static inline int msm_dll_poll_ck_out_en(struct sdhci_host *host, u8 poll) { u32 wait_cnt = 50; u8 ck_out_en; struct mmc_host *mmc = host->mmc; const struct sdhci_msm_offset *msm_offset = sdhci_priv_msm_offset(host); /* Poll for CK_OUT_EN bit. max. poll time = 50us */ ck_out_en = !!(readl_relaxed(host->ioaddr + msm_offset->core_dll_config) & CORE_CK_OUT_EN); while (ck_out_en != poll) { if (--wait_cnt == 0) { dev_err(mmc_dev(mmc), "%s: CK_OUT_EN bit is not %d\n", mmc_hostname(mmc), poll); return -ETIMEDOUT; } udelay(1); ck_out_en = !!(readl_relaxed(host->ioaddr + msm_offset->core_dll_config) & CORE_CK_OUT_EN); } return 0; } static int msm_config_cm_dll_phase(struct sdhci_host *host, u8 phase) { int rc; static const u8 grey_coded_phase_table[] = { 0x0, 0x1, 0x3, 0x2, 0x6, 0x7, 0x5, 0x4, 0xc, 0xd, 0xf, 0xe, 0xa, 0xb, 0x9, 0x8 }; unsigned long flags; u32 config; struct mmc_host *mmc = host->mmc; const struct sdhci_msm_offset *msm_offset = sdhci_priv_msm_offset(host); if (phase > 0xf) return -EINVAL; spin_lock_irqsave(&host->lock, flags); config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config &= ~(CORE_CDR_EN | CORE_CK_OUT_EN); config |= (CORE_CDR_EXT_EN | CORE_DLL_EN); writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); /* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '0' */ rc = msm_dll_poll_ck_out_en(host, 0); if (rc) goto err_out; /* * Write the selected DLL clock output phase (0 ... 15) * to CDR_SELEXT bit field of DLL_CONFIG register. */ config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config &= ~CDR_SELEXT_MASK; config |= grey_coded_phase_table[phase] << CDR_SELEXT_SHIFT; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config |= CORE_CK_OUT_EN; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); /* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '1' */ rc = msm_dll_poll_ck_out_en(host, 1); if (rc) goto err_out; config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config |= CORE_CDR_EN; config &= ~CORE_CDR_EXT_EN; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); goto out; err_out: dev_err(mmc_dev(mmc), "%s: Failed to set DLL phase: %d\n", mmc_hostname(mmc), phase); out: spin_unlock_irqrestore(&host->lock, flags); return rc; } /* * Find out the greatest range of consecuitive selected * DLL clock output phases that can be used as sampling * setting for SD3.0 UHS-I card read operation (in SDR104 * timing mode) or for eMMC4.5 card read operation (in * HS400/HS200 timing mode). * Select the 3/4 of the range and configure the DLL with the * selected DLL clock output phase. */ static int msm_find_most_appropriate_phase(struct sdhci_host *host, u8 *phase_table, u8 total_phases) { int ret; u8 ranges[MAX_PHASES][MAX_PHASES] = { {0}, {0} }; u8 phases_per_row[MAX_PHASES] = { 0 }; int row_index = 0, col_index = 0, selected_row_index = 0, curr_max = 0; int i, cnt, phase_0_raw_index = 0, phase_15_raw_index = 0; bool phase_0_found = false, phase_15_found = false; struct mmc_host *mmc = host->mmc; if (!total_phases || (total_phases > MAX_PHASES)) { dev_err(mmc_dev(mmc), "%s: Invalid argument: total_phases=%d\n", mmc_hostname(mmc), total_phases); return -EINVAL; } for (cnt = 0; cnt < total_phases; cnt++) { ranges[row_index][col_index] = phase_table[cnt]; phases_per_row[row_index] += 1; col_index++; if ((cnt + 1) == total_phases) { continue; /* check if next phase in phase_table is consecutive or not */ } else if ((phase_table[cnt] + 1) != phase_table[cnt + 1]) { row_index++; col_index = 0; } } if (row_index >= MAX_PHASES) return -EINVAL; /* Check if phase-0 is present in first valid window? */ if (!ranges[0][0]) { phase_0_found = true; phase_0_raw_index = 0; /* Check if cycle exist between 2 valid windows */ for (cnt = 1; cnt <= row_index; cnt++) { if (phases_per_row[cnt]) { for (i = 0; i < phases_per_row[cnt]; i++) { if (ranges[cnt][i] == 15) { phase_15_found = true; phase_15_raw_index = cnt; break; } } } } } /* If 2 valid windows form cycle then merge them as single window */ if (phase_0_found && phase_15_found) { /* number of phases in raw where phase 0 is present */ u8 phases_0 = phases_per_row[phase_0_raw_index]; /* number of phases in raw where phase 15 is present */ u8 phases_15 = phases_per_row[phase_15_raw_index]; if (phases_0 + phases_15 >= MAX_PHASES) /* * If there are more than 1 phase windows then total * number of phases in both the windows should not be * more than or equal to MAX_PHASES. */ return -EINVAL; /* Merge 2 cyclic windows */ i = phases_15; for (cnt = 0; cnt < phases_0; cnt++) { ranges[phase_15_raw_index][i] = ranges[phase_0_raw_index][cnt]; if (++i >= MAX_PHASES) break; } phases_per_row[phase_0_raw_index] = 0; phases_per_row[phase_15_raw_index] = phases_15 + phases_0; } for (cnt = 0; cnt <= row_index; cnt++) { if (phases_per_row[cnt] > curr_max) { curr_max = phases_per_row[cnt]; selected_row_index = cnt; } } i = (curr_max * 3) / 4; if (i) i--; ret = ranges[selected_row_index][i]; if (ret >= MAX_PHASES) { ret = -EINVAL; dev_err(mmc_dev(mmc), "%s: Invalid phase selected=%d\n", mmc_hostname(mmc), ret); } return ret; } static inline void msm_cm_dll_set_freq(struct sdhci_host *host) { u32 mclk_freq = 0, config; const struct sdhci_msm_offset *msm_offset = sdhci_priv_msm_offset(host); /* Program the MCLK value to MCLK_FREQ bit field */ if (host->clock <= 112000000) mclk_freq = 0; else if (host->clock <= 125000000) mclk_freq = 1; else if (host->clock <= 137000000) mclk_freq = 2; else if (host->clock <= 150000000) mclk_freq = 3; else if (host->clock <= 162000000) mclk_freq = 4; else if (host->clock <= 175000000) mclk_freq = 5; else if (host->clock <= 187000000) mclk_freq = 6; else if (host->clock <= 200000000) mclk_freq = 7; config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config &= ~CMUX_SHIFT_PHASE_MASK; config |= mclk_freq << CMUX_SHIFT_PHASE_SHIFT; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); } /* Initialize the DLL (Programmable Delay Line) */ static int msm_init_cm_dll(struct sdhci_host *host) { struct mmc_host *mmc = host->mmc; struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); int wait_cnt = 50; unsigned long flags, xo_clk = 0; u32 config; const struct sdhci_msm_offset *msm_offset = msm_host->offset; if (msm_host->use_14lpp_dll_reset && !IS_ERR_OR_NULL(msm_host->xo_clk)) xo_clk = clk_get_rate(msm_host->xo_clk); spin_lock_irqsave(&host->lock, flags); /* * Make sure that clock is always enabled when DLL * tuning is in progress. Keeping PWRSAVE ON may * turn off the clock. */ config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec); config &= ~CORE_CLK_PWRSAVE; writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec); if (msm_host->dll_config) writel_relaxed(msm_host->dll_config, host->ioaddr + msm_offset->core_dll_config); if (msm_host->use_14lpp_dll_reset) { config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config &= ~CORE_CK_OUT_EN; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config_2); config |= CORE_DLL_CLOCK_DISABLE; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config_2); } config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config |= CORE_DLL_RST; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config |= CORE_DLL_PDN; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); if (!msm_host->dll_config) msm_cm_dll_set_freq(host); if (msm_host->use_14lpp_dll_reset && !IS_ERR_OR_NULL(msm_host->xo_clk)) { u32 mclk_freq = 0; config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config_2); config &= CORE_FLL_CYCLE_CNT; if (config) mclk_freq = DIV_ROUND_CLOSEST_ULL((host->clock * 8), xo_clk); else mclk_freq = DIV_ROUND_CLOSEST_ULL((host->clock * 4), xo_clk); config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config_2); config &= ~(0xFF << 10); config |= mclk_freq << 10; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config_2); /* wait for 5us before enabling DLL clock */ udelay(5); } config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config &= ~CORE_DLL_RST; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config &= ~CORE_DLL_PDN; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); if (msm_host->use_14lpp_dll_reset) { if (!msm_host->dll_config) msm_cm_dll_set_freq(host); config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config_2); config &= ~CORE_DLL_CLOCK_DISABLE; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config_2); } /* * Configure DLL user control register to enable DLL status. * This setting is applicable to SDCC v5.1 onwards only. */ if (msm_host->uses_tassadar_dll) { config = DLL_USR_CTL_POR_VAL | FINE_TUNE_MODE_EN | ENABLE_DLL_LOCK_STATUS | BIAS_OK_SIGNAL; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_usr_ctl); config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config_3); config &= ~0xFF; if (msm_host->clk_rate < 150000000) config |= DLL_CONFIG_3_LOW_FREQ_VAL; else config |= DLL_CONFIG_3_HIGH_FREQ_VAL; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config_3); } config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config |= CORE_DLL_EN; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config |= CORE_CK_OUT_EN; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); /* Wait until DLL_LOCK bit of DLL_STATUS register becomes '1' */ while (!(readl_relaxed(host->ioaddr + msm_offset->core_dll_status) & CORE_DLL_LOCK)) { /* max. wait for 50us sec for LOCK bit to be set */ if (--wait_cnt == 0) { dev_err(mmc_dev(mmc), "%s: DLL failed to LOCK\n", mmc_hostname(mmc)); spin_unlock_irqrestore(&host->lock, flags); return -ETIMEDOUT; } udelay(1); } spin_unlock_irqrestore(&host->lock, flags); return 0; } static void msm_hc_select_default(struct sdhci_host *host) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); u32 config; const struct sdhci_msm_offset *msm_offset = msm_host->offset; if (!msm_host->use_cdclp533) { config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec3); config &= ~CORE_PWRSAVE_DLL; writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec3); } config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec); config &= ~CORE_HC_MCLK_SEL_MASK; config |= CORE_HC_MCLK_SEL_DFLT; writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec); /* * Disable HC_SELECT_IN to be able to use the UHS mode select * configuration from Host Control2 register for all other * modes. * Write 0 to HC_SELECT_IN and HC_SELECT_IN_EN field * in VENDOR_SPEC_FUNC */ config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec); config &= ~CORE_HC_SELECT_IN_EN; config &= ~CORE_HC_SELECT_IN_MASK; writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec); /* * Make sure above writes impacting free running MCLK are completed * before changing the clk_rate at GCC. */ wmb(); } static void msm_hc_select_hs400(struct sdhci_host *host) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); struct mmc_ios ios = host->mmc->ios; u32 config, dll_lock; int rc; const struct sdhci_msm_offset *msm_offset = msm_host->offset; /* Select the divided clock (free running MCLK/2) */ config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec); config &= ~CORE_HC_MCLK_SEL_MASK; config |= CORE_HC_MCLK_SEL_HS400; writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec); /* * Select HS400 mode using the HC_SELECT_IN from VENDOR SPEC * register */ if ((msm_host->tuning_done || ios.enhanced_strobe) && !msm_host->calibration_done) { config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec); config |= CORE_HC_SELECT_IN_HS400; config |= CORE_HC_SELECT_IN_EN; writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec); } if (!msm_host->clk_rate && !msm_host->use_cdclp533) { /* * Poll on DLL_LOCK or DDR_DLL_LOCK bits in * core_dll_status to be set. This should get set * within 15 us at 200 MHz. */ rc = readl_relaxed_poll_timeout(host->ioaddr + msm_offset->core_dll_status, dll_lock, (dll_lock & (CORE_DLL_LOCK | CORE_DDR_DLL_LOCK)), 10, 1000); if (rc == -ETIMEDOUT) pr_err("%s: Unable to get DLL_LOCK/DDR_DLL_LOCK, dll_status: 0x%08x\n", mmc_hostname(host->mmc), dll_lock); } /* * Make sure above writes impacting free running MCLK are completed * before changing the clk_rate at GCC. */ wmb(); } /* * sdhci_msm_hc_select_mode :- In general all timing modes are * controlled via UHS mode select in Host Control2 register. * eMMC specific HS200/HS400 doesn't have their respective modes * defined here, hence we use these values. * * HS200 - SDR104 (Since they both are equivalent in functionality) * HS400 - This involves multiple configurations * Initially SDR104 - when tuning is required as HS200 * Then when switching to DDR @ 400MHz (HS400) we use * the vendor specific HC_SELECT_IN to control the mode. * * In addition to controlling the modes we also need to select the * correct input clock for DLL depending on the mode. * * HS400 - divided clock (free running MCLK/2) * All other modes - default (free running MCLK) */ static void sdhci_msm_hc_select_mode(struct sdhci_host *host) { struct mmc_ios ios = host->mmc->ios; if (ios.timing == MMC_TIMING_MMC_HS400 || host->flags & SDHCI_HS400_TUNING) msm_hc_select_hs400(host); else msm_hc_select_default(host); } static int sdhci_msm_cdclp533_calibration(struct sdhci_host *host) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); u32 config, calib_done; int ret; const struct sdhci_msm_offset *msm_offset = msm_host->offset; pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__); /* * Retuning in HS400 (DDR mode) will fail, just reset the * tuning block and restore the saved tuning phase. */ ret = msm_init_cm_dll(host); if (ret) goto out; /* Set the selected phase in delay line hw block */ ret = msm_config_cm_dll_phase(host, msm_host->saved_tuning_phase); if (ret) goto out; config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config |= CORE_CMD_DAT_TRACK_SEL; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); config = readl_relaxed(host->ioaddr + msm_offset->core_ddr_200_cfg); config &= ~CORE_CDC_T4_DLY_SEL; writel_relaxed(config, host->ioaddr + msm_offset->core_ddr_200_cfg); config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG); config &= ~CORE_CDC_SWITCH_BYPASS_OFF; writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_GEN_CFG); config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG); config |= CORE_CDC_SWITCH_RC_EN; writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_GEN_CFG); config = readl_relaxed(host->ioaddr + msm_offset->core_ddr_200_cfg); config &= ~CORE_START_CDC_TRAFFIC; writel_relaxed(config, host->ioaddr + msm_offset->core_ddr_200_cfg); /* Perform CDC Register Initialization Sequence */ writel_relaxed(0x11800EC, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); writel_relaxed(0x3011111, host->ioaddr + CORE_CSR_CDC_CTLR_CFG1); writel_relaxed(0x1201000, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0); writel_relaxed(0x4, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG1); writel_relaxed(0xCB732020, host->ioaddr + CORE_CSR_CDC_REFCOUNT_CFG); writel_relaxed(0xB19, host->ioaddr + CORE_CSR_CDC_COARSE_CAL_CFG); writel_relaxed(0x4E2, host->ioaddr + CORE_CSR_CDC_DELAY_CFG); writel_relaxed(0x0, host->ioaddr + CORE_CDC_OFFSET_CFG); writel_relaxed(0x16334, host->ioaddr + CORE_CDC_SLAVE_DDA_CFG); /* CDC HW Calibration */ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); config |= CORE_SW_TRIG_FULL_CALIB; writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); config &= ~CORE_SW_TRIG_FULL_CALIB; writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); config |= CORE_HW_AUTOCAL_ENA; writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0); config |= CORE_TIMER_ENA; writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0); ret = readl_relaxed_poll_timeout(host->ioaddr + CORE_CSR_CDC_STATUS0, calib_done, (calib_done & CORE_CALIBRATION_DONE), 1, 50); if (ret == -ETIMEDOUT) { pr_err("%s: %s: CDC calibration was not completed\n", mmc_hostname(host->mmc), __func__); goto out; } ret = readl_relaxed(host->ioaddr + CORE_CSR_CDC_STATUS0) & CORE_CDC_ERROR_CODE_MASK; if (ret) { pr_err("%s: %s: CDC error code %d\n", mmc_hostname(host->mmc), __func__, ret); ret = -EINVAL; goto out; } config = readl_relaxed(host->ioaddr + msm_offset->core_ddr_200_cfg); config |= CORE_START_CDC_TRAFFIC; writel_relaxed(config, host->ioaddr + msm_offset->core_ddr_200_cfg); out: pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc), __func__, ret); return ret; } static int sdhci_msm_cm_dll_sdc4_calibration(struct sdhci_host *host) { struct mmc_host *mmc = host->mmc; u32 dll_status, config, ddr_cfg_offset; int ret; struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); const struct sdhci_msm_offset *msm_offset = sdhci_priv_msm_offset(host); pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__); /* * Currently the core_ddr_config register defaults to desired * configuration on reset. Currently reprogramming the power on * reset (POR) value in case it might have been modified by * bootloaders. In the future, if this changes, then the desired * values will need to be programmed appropriately. */ if (msm_host->updated_ddr_cfg) ddr_cfg_offset = msm_offset->core_ddr_config; else ddr_cfg_offset = msm_offset->core_ddr_config_old; writel_relaxed(msm_host->ddr_config, host->ioaddr + ddr_cfg_offset); if (mmc->ios.enhanced_strobe) { config = readl_relaxed(host->ioaddr + msm_offset->core_ddr_200_cfg); config |= CORE_CMDIN_RCLK_EN; writel_relaxed(config, host->ioaddr + msm_offset->core_ddr_200_cfg); } config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config_2); config |= CORE_DDR_CAL_EN; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config_2); ret = readl_relaxed_poll_timeout(host->ioaddr + msm_offset->core_dll_status, dll_status, (dll_status & CORE_DDR_DLL_LOCK), 10, 1000); if (ret == -ETIMEDOUT) { pr_err("%s: %s: CM_DLL_SDC4 calibration was not completed\n", mmc_hostname(host->mmc), __func__); goto out; } /* * Set CORE_PWRSAVE_DLL bit in CORE_VENDOR_SPEC3. * When MCLK is gated OFF, it is not gated for less than 0.5us * and MCLK must be switched on for at-least 1us before DATA * starts coming. Controllers with 14lpp and later tech DLL cannot * guarantee above requirement. So PWRSAVE_DLL should not be * turned on for host controllers using this DLL. */ if (!msm_host->use_14lpp_dll_reset) { config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec3); config |= CORE_PWRSAVE_DLL; writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec3); } /* * Drain writebuffer to ensure above DLL calibration * and PWRSAVE DLL is enabled. */ wmb(); out: pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc), __func__, ret); return ret; } static int sdhci_msm_hs400_dll_calibration(struct sdhci_host *host) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); struct mmc_host *mmc = host->mmc; int ret; u32 config; const struct sdhci_msm_offset *msm_offset = msm_host->offset; pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__); /* * Retuning in HS400 (DDR mode) will fail, just reset the * tuning block and restore the saved tuning phase. */ ret = msm_init_cm_dll(host); if (ret) goto out; if (!mmc->ios.enhanced_strobe) { /* Set the selected phase in delay line hw block */ ret = msm_config_cm_dll_phase(host, msm_host->saved_tuning_phase); if (ret) goto out; config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config |= CORE_CMD_DAT_TRACK_SEL; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); } if (msm_host->use_cdclp533) ret = sdhci_msm_cdclp533_calibration(host); else ret = sdhci_msm_cm_dll_sdc4_calibration(host); out: pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc), __func__, ret); return ret; } static bool sdhci_msm_is_tuning_needed(struct sdhci_host *host) { struct mmc_ios *ios = &host->mmc->ios; /* * Tuning is required for SDR104, HS200 and HS400 cards and * if clock frequency is greater than 100MHz in these modes. */ if (host->clock <= CORE_FREQ_100MHZ || !(ios->timing == MMC_TIMING_MMC_HS400 || ios->timing == MMC_TIMING_MMC_HS200 || ios->timing == MMC_TIMING_UHS_SDR104) || ios->enhanced_strobe) return false; return true; } static int sdhci_msm_restore_sdr_dll_config(struct sdhci_host *host) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); int ret; /* * SDR DLL comes into picture only for timing modes which needs * tuning. */ if (!sdhci_msm_is_tuning_needed(host)) return 0; /* Reset the tuning block */ ret = msm_init_cm_dll(host); if (ret) return ret; /* Restore the tuning block */ ret = msm_config_cm_dll_phase(host, msm_host->saved_tuning_phase); return ret; } static void sdhci_msm_set_cdr(struct sdhci_host *host, bool enable) { const struct sdhci_msm_offset *msm_offset = sdhci_priv_msm_offset(host); u32 config, oldconfig = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config = oldconfig; if (enable) { config |= CORE_CDR_EN; config &= ~CORE_CDR_EXT_EN; } else { config &= ~CORE_CDR_EN; config |= CORE_CDR_EXT_EN; } if (config != oldconfig) { writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); } } static int sdhci_msm_execute_tuning(struct mmc_host *mmc, u32 opcode) { struct sdhci_host *host = mmc_priv(mmc); int tuning_seq_cnt = 10; u8 phase, tuned_phases[16], tuned_phase_cnt = 0; int rc; struct mmc_ios ios = host->mmc->ios; struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); if (!sdhci_msm_is_tuning_needed(host)) { msm_host->use_cdr = false; sdhci_msm_set_cdr(host, false); return 0; } /* Clock-Data-Recovery used to dynamically adjust RX sampling point */ msm_host->use_cdr = true; /* * Clear tuning_done flag before tuning to ensure proper * HS400 settings. */ msm_host->tuning_done = 0; /* * For HS400 tuning in HS200 timing requires: * - select MCLK/2 in VENDOR_SPEC * - program MCLK to 400MHz (or nearest supported) in GCC */ if (host->flags & SDHCI_HS400_TUNING) { sdhci_msm_hc_select_mode(host); msm_set_clock_rate_for_bus_mode(host, ios.clock); host->flags &= ~SDHCI_HS400_TUNING; } retry: /* First of all reset the tuning block */ rc = msm_init_cm_dll(host); if (rc) return rc; phase = 0; do { /* Set the phase in delay line hw block */ rc = msm_config_cm_dll_phase(host, phase); if (rc) return rc; rc = mmc_send_tuning(mmc, opcode, NULL); if (!rc) { /* Tuning is successful at this tuning point */ tuned_phases[tuned_phase_cnt++] = phase; dev_dbg(mmc_dev(mmc), "%s: Found good phase = %d\n", mmc_hostname(mmc), phase); } } while (++phase < ARRAY_SIZE(tuned_phases)); if (tuned_phase_cnt) { if (tuned_phase_cnt == ARRAY_SIZE(tuned_phases)) { /* * All phases valid is _almost_ as bad as no phases * valid. Probably all phases are not really reliable * but we didn't detect where the unreliable place is. * That means we'll essentially be guessing and hoping * we get a good phase. Better to try a few times. */ dev_dbg(mmc_dev(mmc), "%s: All phases valid; try again\n", mmc_hostname(mmc)); if (--tuning_seq_cnt) { tuned_phase_cnt = 0; goto retry; } } rc = msm_find_most_appropriate_phase(host, tuned_phases, tuned_phase_cnt); if (rc < 0) return rc; else phase = rc; /* * Finally set the selected phase in delay * line hw block. */ rc = msm_config_cm_dll_phase(host, phase); if (rc) return rc; msm_host->saved_tuning_phase = phase; dev_dbg(mmc_dev(mmc), "%s: Setting the tuning phase to %d\n", mmc_hostname(mmc), phase); } else { if (--tuning_seq_cnt) goto retry; /* Tuning failed */ dev_dbg(mmc_dev(mmc), "%s: No tuning point found\n", mmc_hostname(mmc)); rc = -EIO; } if (!rc) msm_host->tuning_done = true; return rc; } /* * sdhci_msm_hs400 - Calibrate the DLL for HS400 bus speed mode operation. * This needs to be done for both tuning and enhanced_strobe mode. * DLL operation is only needed for clock > 100MHz. For clock <= 100MHz * fixed feedback clock is used. */ static void sdhci_msm_hs400(struct sdhci_host *host, struct mmc_ios *ios) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); int ret; if (host->clock > CORE_FREQ_100MHZ && (msm_host->tuning_done || ios->enhanced_strobe) && !msm_host->calibration_done) { ret = sdhci_msm_hs400_dll_calibration(host); if (!ret) msm_host->calibration_done = true; else pr_err("%s: Failed to calibrate DLL for hs400 mode (%d)\n", mmc_hostname(host->mmc), ret); } } static void sdhci_msm_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs) { struct mmc_host *mmc = host->mmc; struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); u16 ctrl_2; u32 config; const struct sdhci_msm_offset *msm_offset = msm_host->offset; ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); /* Select Bus Speed Mode for host */ ctrl_2 &= ~SDHCI_CTRL_UHS_MASK; switch (uhs) { case MMC_TIMING_UHS_SDR12: ctrl_2 |= SDHCI_CTRL_UHS_SDR12; break; case MMC_TIMING_UHS_SDR25: ctrl_2 |= SDHCI_CTRL_UHS_SDR25; break; case MMC_TIMING_UHS_SDR50: ctrl_2 |= SDHCI_CTRL_UHS_SDR50; break; case MMC_TIMING_MMC_HS400: case MMC_TIMING_MMC_HS200: case MMC_TIMING_UHS_SDR104: ctrl_2 |= SDHCI_CTRL_UHS_SDR104; break; case MMC_TIMING_UHS_DDR50: case MMC_TIMING_MMC_DDR52: ctrl_2 |= SDHCI_CTRL_UHS_DDR50; break; } /* * When clock frequency is less than 100MHz, the feedback clock must be * provided and DLL must not be used so that tuning can be skipped. To * provide feedback clock, the mode selection can be any value less * than 3'b011 in bits [2:0] of HOST CONTROL2 register. */ if (host->clock <= CORE_FREQ_100MHZ) { if (uhs == MMC_TIMING_MMC_HS400 || uhs == MMC_TIMING_MMC_HS200 || uhs == MMC_TIMING_UHS_SDR104) ctrl_2 &= ~SDHCI_CTRL_UHS_MASK; /* * DLL is not required for clock <= 100MHz * Thus, make sure DLL it is disabled when not required */ config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config |= CORE_DLL_RST; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config); config |= CORE_DLL_PDN; writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config); /* * The DLL needs to be restored and CDCLP533 recalibrated * when the clock frequency is set back to 400MHz. */ msm_host->calibration_done = false; } dev_dbg(mmc_dev(mmc), "%s: clock=%u uhs=%u ctrl_2=0x%x\n", mmc_hostname(host->mmc), host->clock, uhs, ctrl_2); sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); if (mmc->ios.timing == MMC_TIMING_MMC_HS400) sdhci_msm_hs400(host, &mmc->ios); } static int sdhci_msm_set_pincfg(struct sdhci_msm_host *msm_host, bool level) { struct platform_device *pdev = msm_host->pdev; int ret; if (level) ret = pinctrl_pm_select_default_state(&pdev->dev); else ret = pinctrl_pm_select_sleep_state(&pdev->dev); return ret; } static int sdhci_msm_set_vmmc(struct mmc_host *mmc) { if (IS_ERR(mmc->supply.vmmc)) return 0; return mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, mmc->ios.vdd); } static int msm_toggle_vqmmc(struct sdhci_msm_host *msm_host, struct mmc_host *mmc, bool level) { int ret; struct mmc_ios ios; if (msm_host->vqmmc_enabled == level) return 0; if (level) { /* Set the IO voltage regulator to default voltage level */ if (msm_host->caps_0 & CORE_3_0V_SUPPORT) ios.signal_voltage = MMC_SIGNAL_VOLTAGE_330; else if (msm_host->caps_0 & CORE_1_8V_SUPPORT) ios.signal_voltage = MMC_SIGNAL_VOLTAGE_180; if (msm_host->caps_0 & CORE_VOLT_SUPPORT) { ret = mmc_regulator_set_vqmmc(mmc, &ios); if (ret < 0) { dev_err(mmc_dev(mmc), "%s: vqmmc set volgate failed: %d\n", mmc_hostname(mmc), ret); goto out; } } ret = regulator_enable(mmc->supply.vqmmc); } else { ret = regulator_disable(mmc->supply.vqmmc); } if (ret) dev_err(mmc_dev(mmc), "%s: vqmm %sable failed: %d\n", mmc_hostname(mmc), level ? "en":"dis", ret); else msm_host->vqmmc_enabled = level; out: return ret; } static int msm_config_vqmmc_mode(struct sdhci_msm_host *msm_host, struct mmc_host *mmc, bool hpm) { int load, ret; load = hpm ? MMC_VQMMC_MAX_LOAD_UA : 0; ret = regulator_set_load(mmc->supply.vqmmc, load); if (ret) dev_err(mmc_dev(mmc), "%s: vqmmc set load failed: %d\n", mmc_hostname(mmc), ret); return ret; } static int sdhci_msm_set_vqmmc(struct sdhci_msm_host *msm_host, struct mmc_host *mmc, bool level) { int ret; bool always_on; if (IS_ERR(mmc->supply.vqmmc) || (mmc->ios.power_mode == MMC_POWER_UNDEFINED)) return 0; /* * For eMMC don't turn off Vqmmc, Instead just configure it in LPM * and HPM modes by setting the corresponding load. * * Till eMMC is initialized (i.e. always_on == 0), just turn on/off * Vqmmc. Vqmmc gets turned off only if init fails and mmc_power_off * gets invoked. Once eMMC is initialized (i.e. always_on == 1), * Vqmmc should remain ON, So just set the load instead of turning it * off/on. */ always_on = !mmc_card_is_removable(mmc) && mmc->card && mmc_card_mmc(mmc->card); if (always_on) ret = msm_config_vqmmc_mode(msm_host, mmc, level); else ret = msm_toggle_vqmmc(msm_host, mmc, level); return ret; } static inline void sdhci_msm_init_pwr_irq_wait(struct sdhci_msm_host *msm_host) { init_waitqueue_head(&msm_host->pwr_irq_wait); } static inline void sdhci_msm_complete_pwr_irq_wait( struct sdhci_msm_host *msm_host) { wake_up(&msm_host->pwr_irq_wait); } /* * sdhci_msm_check_power_status API should be called when registers writes * which can toggle sdhci IO bus ON/OFF or change IO lines HIGH/LOW happens. * To what state the register writes will change the IO lines should be passed * as the argument req_type. This API will check whether the IO line's state * is already the expected state and will wait for power irq only if * power irq is expected to be triggered based on the current IO line state * and expected IO line state. */ static void sdhci_msm_check_power_status(struct sdhci_host *host, u32 req_type) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); bool done = false; u32 val = SWITCHABLE_SIGNALING_VOLTAGE; const struct sdhci_msm_offset *msm_offset = msm_host->offset; pr_debug("%s: %s: request %d curr_pwr_state %x curr_io_level %x\n", mmc_hostname(host->mmc), __func__, req_type, msm_host->curr_pwr_state, msm_host->curr_io_level); /* * The power interrupt will not be generated for signal voltage * switches if SWITCHABLE_SIGNALING_VOLTAGE in MCI_GENERICS is not set. * Since sdhci-msm-v5, this bit has been removed and SW must consider * it as always set. */ if (!msm_host->mci_removed) val = msm_host_readl(msm_host, host, msm_offset->core_generics); if ((req_type & REQ_IO_HIGH || req_type & REQ_IO_LOW) && !(val & SWITCHABLE_SIGNALING_VOLTAGE)) { return; } /* * The IRQ for request type IO High/LOW will be generated when - * there is a state change in 1.8V enable bit (bit 3) of * SDHCI_HOST_CONTROL2 register. The reset state of that bit is 0 * which indicates 3.3V IO voltage. So, when MMC core layer tries * to set it to 3.3V before card detection happens, the * IRQ doesn't get triggered as there is no state change in this bit. * The driver already handles this case by changing the IO voltage * level to high as part of controller power up sequence. Hence, check * for host->pwr to handle a case where IO voltage high request is * issued even before controller power up. */ if ((req_type & REQ_IO_HIGH) && !host->pwr) { pr_debug("%s: do not wait for power IRQ that never comes, req_type: %d\n", mmc_hostname(host->mmc), req_type); return; } if ((req_type & msm_host->curr_pwr_state) || (req_type & msm_host->curr_io_level)) done = true; /* * This is needed here to handle cases where register writes will * not change the current bus state or io level of the controller. * In this case, no power irq will be triggerred and we should * not wait. */ if (!done) { if (!wait_event_timeout(msm_host->pwr_irq_wait, msm_host->pwr_irq_flag, msecs_to_jiffies(MSM_PWR_IRQ_TIMEOUT_MS))) dev_warn(&msm_host->pdev->dev, "%s: pwr_irq for req: (%d) timed out\n", mmc_hostname(host->mmc), req_type); } pr_debug("%s: %s: request %d done\n", mmc_hostname(host->mmc), __func__, req_type); } static void sdhci_msm_dump_pwr_ctrl_regs(struct sdhci_host *host) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); const struct sdhci_msm_offset *msm_offset = msm_host->offset; pr_err("%s: PWRCTL_STATUS: 0x%08x | PWRCTL_MASK: 0x%08x | PWRCTL_CTL: 0x%08x\n", mmc_hostname(host->mmc), msm_host_readl(msm_host, host, msm_offset->core_pwrctl_status), msm_host_readl(msm_host, host, msm_offset->core_pwrctl_mask), msm_host_readl(msm_host, host, msm_offset->core_pwrctl_ctl)); } static void sdhci_msm_handle_pwr_irq(struct sdhci_host *host, int irq) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); struct mmc_host *mmc = host->mmc; u32 irq_status, irq_ack = 0; int retry = 10, ret; u32 pwr_state = 0, io_level = 0; u32 config; const struct sdhci_msm_offset *msm_offset = msm_host->offset; irq_status = msm_host_readl(msm_host, host, msm_offset->core_pwrctl_status); irq_status &= INT_MASK; msm_host_writel(msm_host, irq_status, host, msm_offset->core_pwrctl_clear); /* * There is a rare HW scenario where the first clear pulse could be * lost when actual reset and clear/read of status register is * happening at a time. Hence, retry for at least 10 times to make * sure status register is cleared. Otherwise, this will result in * a spurious power IRQ resulting in system instability. */ while (irq_status & msm_host_readl(msm_host, host, msm_offset->core_pwrctl_status)) { if (retry == 0) { pr_err("%s: Timedout clearing (0x%x) pwrctl status register\n", mmc_hostname(host->mmc), irq_status); sdhci_msm_dump_pwr_ctrl_regs(host); WARN_ON(1); break; } msm_host_writel(msm_host, irq_status, host, msm_offset->core_pwrctl_clear); retry--; udelay(10); } /* Handle BUS ON/OFF*/ if (irq_status & CORE_PWRCTL_BUS_ON) { pwr_state = REQ_BUS_ON; io_level = REQ_IO_HIGH; } if (irq_status & CORE_PWRCTL_BUS_OFF) { pwr_state = REQ_BUS_OFF; io_level = REQ_IO_LOW; } if (pwr_state) { ret = sdhci_msm_set_vmmc(mmc); if (!ret) ret = sdhci_msm_set_vqmmc(msm_host, mmc, pwr_state & REQ_BUS_ON); if (!ret) ret = sdhci_msm_set_pincfg(msm_host, pwr_state & REQ_BUS_ON); if (!ret) irq_ack |= CORE_PWRCTL_BUS_SUCCESS; else irq_ack |= CORE_PWRCTL_BUS_FAIL; } /* Handle IO LOW/HIGH */ if (irq_status & CORE_PWRCTL_IO_LOW) io_level = REQ_IO_LOW; if (irq_status & CORE_PWRCTL_IO_HIGH) io_level = REQ_IO_HIGH; if (io_level) irq_ack |= CORE_PWRCTL_IO_SUCCESS; if (io_level && !IS_ERR(mmc->supply.vqmmc) && !pwr_state) { ret = mmc_regulator_set_vqmmc(mmc, &mmc->ios); if (ret < 0) { dev_err(mmc_dev(mmc), "%s: IO_level setting failed(%d). signal_voltage: %d, vdd: %d irq_status: 0x%08x\n", mmc_hostname(mmc), ret, mmc->ios.signal_voltage, mmc->ios.vdd, irq_status); irq_ack |= CORE_PWRCTL_IO_FAIL; } } /* * The driver has to acknowledge the interrupt, switch voltages and * report back if it succeded or not to this register. The voltage * switches are handled by the sdhci core, so just report success. */ msm_host_writel(msm_host, irq_ack, host, msm_offset->core_pwrctl_ctl); /* * If we don't have info regarding the voltage levels supported by * regulators, don't change the IO PAD PWR SWITCH. */ if (msm_host->caps_0 & CORE_VOLT_SUPPORT) { u32 new_config; /* * We should unset IO PAD PWR switch only if the register write * can set IO lines high and the regulator also switches to 3 V. * Else, we should keep the IO PAD PWR switch set. * This is applicable to certain targets where eMMC vccq supply * is only 1.8V. In such targets, even during REQ_IO_HIGH, the * IO PAD PWR switch must be kept set to reflect actual * regulator voltage. This way, during initialization of * controllers with only 1.8V, we will set the IO PAD bit * without waiting for a REQ_IO_LOW. */ config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec); new_config = config; if ((io_level & REQ_IO_HIGH) && (msm_host->caps_0 & CORE_3_0V_SUPPORT)) new_config &= ~CORE_IO_PAD_PWR_SWITCH; else if ((io_level & REQ_IO_LOW) || (msm_host->caps_0 & CORE_1_8V_SUPPORT)) new_config |= CORE_IO_PAD_PWR_SWITCH; if (config ^ new_config) writel_relaxed(new_config, host->ioaddr + msm_offset->core_vendor_spec); } if (pwr_state) msm_host->curr_pwr_state = pwr_state; if (io_level) msm_host->curr_io_level = io_level; dev_dbg(mmc_dev(mmc), "%s: %s: Handled IRQ(%d), irq_status=0x%x, ack=0x%x\n", mmc_hostname(msm_host->mmc), __func__, irq, irq_status, irq_ack); } static irqreturn_t sdhci_msm_pwr_irq(int irq, void *data) { struct sdhci_host *host = (struct sdhci_host *)data; struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); sdhci_msm_handle_pwr_irq(host, irq); msm_host->pwr_irq_flag = 1; sdhci_msm_complete_pwr_irq_wait(msm_host); return IRQ_HANDLED; } static unsigned int sdhci_msm_get_max_clock(struct sdhci_host *host) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); struct clk *core_clk = msm_host->bulk_clks[0].clk; return clk_round_rate(core_clk, ULONG_MAX); } static unsigned int sdhci_msm_get_min_clock(struct sdhci_host *host) { return SDHCI_MSM_MIN_CLOCK; } /* * __sdhci_msm_set_clock - sdhci_msm clock control. * * Description: * MSM controller does not use internal divider and * instead directly control the GCC clock as per * HW recommendation. **/ static void __sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock) { u16 clk; /* * Keep actual_clock as zero - * - since there is no divider used so no need of having actual_clock. * - MSM controller uses SDCLK for data timeout calculation. If * actual_clock is zero, host->clock is taken for calculation. */ host->mmc->actual_clock = 0; sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL); if (clock == 0) return; /* * MSM controller do not use clock divider. * Thus read SDHCI_CLOCK_CONTROL and only enable * clock with no divider value programmed. */ clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL); sdhci_enable_clk(host, clk); } /* sdhci_msm_set_clock - Called with (host->lock) spinlock held. */ static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); if (!clock) { msm_host->clk_rate = clock; goto out; } sdhci_msm_hc_select_mode(host); msm_set_clock_rate_for_bus_mode(host, clock); out: __sdhci_msm_set_clock(host, clock); } /*****************************************************************************\ * * * MSM Command Queue Engine (CQE) * * * \*****************************************************************************/ static u32 sdhci_msm_cqe_irq(struct sdhci_host *host, u32 intmask) { int cmd_error = 0; int data_error = 0; if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error)) return intmask; cqhci_irq(host->mmc, intmask, cmd_error, data_error); return 0; } static void sdhci_msm_cqe_disable(struct mmc_host *mmc, bool recovery) { struct sdhci_host *host = mmc_priv(mmc); unsigned long flags; u32 ctrl; /* * When CQE is halted, the legacy SDHCI path operates only * on 16-byte descriptors in 64bit mode. */ if (host->flags & SDHCI_USE_64_BIT_DMA) host->desc_sz = 16; spin_lock_irqsave(&host->lock, flags); /* * During CQE command transfers, command complete bit gets latched. * So s/w should clear command complete interrupt status when CQE is * either halted or disabled. Otherwise unexpected SDCHI legacy * interrupt gets triggered when CQE is halted/disabled. */ ctrl = sdhci_readl(host, SDHCI_INT_ENABLE); ctrl |= SDHCI_INT_RESPONSE; sdhci_writel(host, ctrl, SDHCI_INT_ENABLE); sdhci_writel(host, SDHCI_INT_RESPONSE, SDHCI_INT_STATUS); spin_unlock_irqrestore(&host->lock, flags); sdhci_cqe_disable(mmc, recovery); } static void sdhci_msm_set_timeout(struct sdhci_host *host, struct mmc_command *cmd) { u32 count, start = 15; __sdhci_set_timeout(host, cmd); count = sdhci_readb(host, SDHCI_TIMEOUT_CONTROL); /* * Update software timeout value if its value is less than hardware data * timeout value. Qcom SoC hardware data timeout value was calculated * using 4 * MCLK * 2^(count + 13). where MCLK = 1 / host->clock. */ if (cmd && cmd->data && host->clock > 400000 && host->clock <= 50000000 && ((1 << (count + start)) > (10 * host->clock))) host->data_timeout = 22LL * NSEC_PER_SEC; } static const struct cqhci_host_ops sdhci_msm_cqhci_ops = { .enable = sdhci_cqe_enable, .disable = sdhci_msm_cqe_disable, }; static int sdhci_msm_cqe_add_host(struct sdhci_host *host, struct platform_device *pdev) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); struct cqhci_host *cq_host; bool dma64; u32 cqcfg; int ret; /* * When CQE is halted, SDHC operates only on 16byte ADMA descriptors. * So ensure ADMA table is allocated for 16byte descriptors. */ if (host->caps & SDHCI_CAN_64BIT) host->alloc_desc_sz = 16; ret = sdhci_setup_host(host); if (ret) return ret; cq_host = cqhci_pltfm_init(pdev); if (IS_ERR(cq_host)) { ret = PTR_ERR(cq_host); dev_err(&pdev->dev, "cqhci-pltfm init: failed: %d\n", ret); goto cleanup; } msm_host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD; cq_host->ops = &sdhci_msm_cqhci_ops; dma64 = host->flags & SDHCI_USE_64_BIT_DMA; ret = cqhci_init(cq_host, host->mmc, dma64); if (ret) { dev_err(&pdev->dev, "%s: CQE init: failed (%d)\n", mmc_hostname(host->mmc), ret); goto cleanup; } /* Disable cqe reset due to cqe enable signal */ cqcfg = cqhci_readl(cq_host, CQHCI_VENDOR_CFG1); cqcfg |= CQHCI_VENDOR_DIS_RST_ON_CQ_EN; cqhci_writel(cq_host, cqcfg, CQHCI_VENDOR_CFG1); /* * SDHC expects 12byte ADMA descriptors till CQE is enabled. * So limit desc_sz to 12 so that the data commands that are sent * during card initialization (before CQE gets enabled) would * get executed without any issues. */ if (host->flags & SDHCI_USE_64_BIT_DMA) host->desc_sz = 12; ret = __sdhci_add_host(host); if (ret) goto cleanup; dev_info(&pdev->dev, "%s: CQE init: success\n", mmc_hostname(host->mmc)); return ret; cleanup: sdhci_cleanup_host(host); return ret; } /* * Platform specific register write functions. This is so that, if any * register write needs to be followed up by platform specific actions, * they can be added here. These functions can go to sleep when writes * to certain registers are done. * These functions are relying on sdhci_set_ios not using spinlock. */ static int __sdhci_msm_check_write(struct sdhci_host *host, u16 val, int reg) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); u32 req_type = 0; switch (reg) { case SDHCI_HOST_CONTROL2: req_type = (val & SDHCI_CTRL_VDD_180) ? REQ_IO_LOW : REQ_IO_HIGH; break; case SDHCI_SOFTWARE_RESET: if (host->pwr && (val & SDHCI_RESET_ALL)) req_type = REQ_BUS_OFF; break; case SDHCI_POWER_CONTROL: req_type = !val ? REQ_BUS_OFF : REQ_BUS_ON; break; case SDHCI_TRANSFER_MODE: msm_host->transfer_mode = val; break; case SDHCI_COMMAND: if (!msm_host->use_cdr) break; if ((msm_host->transfer_mode & SDHCI_TRNS_READ) && SDHCI_GET_CMD(val) != MMC_SEND_TUNING_BLOCK_HS200 && SDHCI_GET_CMD(val) != MMC_SEND_TUNING_BLOCK) sdhci_msm_set_cdr(host, true); else sdhci_msm_set_cdr(host, false); break; } if (req_type) { msm_host->pwr_irq_flag = 0; /* * Since this register write may trigger a power irq, ensure * all previous register writes are complete by this point. */ mb(); } return req_type; } /* This function may sleep*/ static void sdhci_msm_writew(struct sdhci_host *host, u16 val, int reg) { u32 req_type = 0; req_type = __sdhci_msm_check_write(host, val, reg); writew_relaxed(val, host->ioaddr + reg); if (req_type) sdhci_msm_check_power_status(host, req_type); } /* This function may sleep*/ static void sdhci_msm_writeb(struct sdhci_host *host, u8 val, int reg) { u32 req_type = 0; req_type = __sdhci_msm_check_write(host, val, reg); writeb_relaxed(val, host->ioaddr + reg); if (req_type) sdhci_msm_check_power_status(host, req_type); } static void sdhci_msm_set_regulator_caps(struct sdhci_msm_host *msm_host) { struct mmc_host *mmc = msm_host->mmc; struct regulator *supply = mmc->supply.vqmmc; u32 caps = 0, config; struct sdhci_host *host = mmc_priv(mmc); const struct sdhci_msm_offset *msm_offset = msm_host->offset; if (!IS_ERR(mmc->supply.vqmmc)) { if (regulator_is_supported_voltage(supply, 1700000, 1950000)) caps |= CORE_1_8V_SUPPORT; if (regulator_is_supported_voltage(supply, 2700000, 3600000)) caps |= CORE_3_0V_SUPPORT; if (!caps) pr_warn("%s: 1.8/3V not supported for vqmmc\n", mmc_hostname(mmc)); } if (caps) { /* * Set the PAD_PWR_SWITCH_EN bit so that the PAD_PWR_SWITCH * bit can be used as required later on. */ u32 io_level = msm_host->curr_io_level; config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec); config |= CORE_IO_PAD_PWR_SWITCH_EN; if ((io_level & REQ_IO_HIGH) && (caps & CORE_3_0V_SUPPORT)) config &= ~CORE_IO_PAD_PWR_SWITCH; else if ((io_level & REQ_IO_LOW) || (caps & CORE_1_8V_SUPPORT)) config |= CORE_IO_PAD_PWR_SWITCH; writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec); } msm_host->caps_0 |= caps; pr_debug("%s: supported caps: 0x%08x\n", mmc_hostname(mmc), caps); } static void sdhci_msm_reset(struct sdhci_host *host, u8 mask) { if ((host->mmc->caps2 & MMC_CAP2_CQE) && (mask & SDHCI_RESET_ALL)) cqhci_deactivate(host->mmc); sdhci_reset(host, mask); } static int sdhci_msm_register_vreg(struct sdhci_msm_host *msm_host) { int ret; ret = mmc_regulator_get_supply(msm_host->mmc); if (ret) return ret; sdhci_msm_set_regulator_caps(msm_host); return 0; } static int sdhci_msm_start_signal_voltage_switch(struct mmc_host *mmc, struct mmc_ios *ios) { struct sdhci_host *host = mmc_priv(mmc); u16 ctrl, status; /* * Signal Voltage Switching is only applicable for Host Controllers * v3.00 and above. */ if (host->version < SDHCI_SPEC_300) return 0; ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2); switch (ios->signal_voltage) { case MMC_SIGNAL_VOLTAGE_330: if (!(host->flags & SDHCI_SIGNALING_330)) return -EINVAL; /* Set 1.8V Signal Enable in the Host Control2 register to 0 */ ctrl &= ~SDHCI_CTRL_VDD_180; break; case MMC_SIGNAL_VOLTAGE_180: if (!(host->flags & SDHCI_SIGNALING_180)) return -EINVAL; /* Enable 1.8V Signal Enable in the Host Control2 register */ ctrl |= SDHCI_CTRL_VDD_180; break; default: return -EINVAL; } sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2); /* Wait for 5ms */ usleep_range(5000, 5500); /* regulator output should be stable within 5 ms */ status = ctrl & SDHCI_CTRL_VDD_180; ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2); if ((ctrl & SDHCI_CTRL_VDD_180) == status) return 0; dev_warn(mmc_dev(mmc), "%s: Regulator output did not became stable\n", mmc_hostname(mmc)); return -EAGAIN; } #define DRIVER_NAME "sdhci_msm" #define SDHCI_MSM_DUMP(f, x...) \ pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x) static void sdhci_msm_dump_vendor_regs(struct sdhci_host *host) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); const struct sdhci_msm_offset *msm_offset = msm_host->offset; SDHCI_MSM_DUMP("----------- VENDOR REGISTER DUMP -----------\n"); SDHCI_MSM_DUMP( "DLL sts: 0x%08x | DLL cfg: 0x%08x | DLL cfg2: 0x%08x\n", readl_relaxed(host->ioaddr + msm_offset->core_dll_status), readl_relaxed(host->ioaddr + msm_offset->core_dll_config), readl_relaxed(host->ioaddr + msm_offset->core_dll_config_2)); SDHCI_MSM_DUMP( "DLL cfg3: 0x%08x | DLL usr ctl: 0x%08x | DDR cfg: 0x%08x\n", readl_relaxed(host->ioaddr + msm_offset->core_dll_config_3), readl_relaxed(host->ioaddr + msm_offset->core_dll_usr_ctl), readl_relaxed(host->ioaddr + msm_offset->core_ddr_config)); SDHCI_MSM_DUMP( "Vndr func: 0x%08x | Vndr func2 : 0x%08x Vndr func3: 0x%08x\n", readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec), readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec_func2), readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec3)); } static const struct sdhci_msm_variant_ops mci_var_ops = { .msm_readl_relaxed = sdhci_msm_mci_variant_readl_relaxed, .msm_writel_relaxed = sdhci_msm_mci_variant_writel_relaxed, }; static const struct sdhci_msm_variant_ops v5_var_ops = { .msm_readl_relaxed = sdhci_msm_v5_variant_readl_relaxed, .msm_writel_relaxed = sdhci_msm_v5_variant_writel_relaxed, }; static const struct sdhci_msm_variant_info sdhci_msm_mci_var = { .var_ops = &mci_var_ops, .offset = &sdhci_msm_mci_offset, }; static const struct sdhci_msm_variant_info sdhci_msm_v5_var = { .mci_removed = true, .var_ops = &v5_var_ops, .offset = &sdhci_msm_v5_offset, }; static const struct sdhci_msm_variant_info sdm845_sdhci_var = { .mci_removed = true, .restore_dll_config = true, .var_ops = &v5_var_ops, .offset = &sdhci_msm_v5_offset, }; static const struct sdhci_msm_variant_info sm8250_sdhci_var = { .mci_removed = true, .uses_tassadar_dll = true, .var_ops = &v5_var_ops, .offset = &sdhci_msm_v5_offset, }; static const struct of_device_id sdhci_msm_dt_match[] = { {.compatible = "qcom,sdhci-msm-v4", .data = &sdhci_msm_mci_var}, {.compatible = "qcom,sdhci-msm-v5", .data = &sdhci_msm_v5_var}, {.compatible = "qcom,sdm670-sdhci", .data = &sdm845_sdhci_var}, {.compatible = "qcom,sdm845-sdhci", .data = &sdm845_sdhci_var}, {.compatible = "qcom,sm8250-sdhci", .data = &sm8250_sdhci_var}, {.compatible = "qcom,sc7180-sdhci", .data = &sdm845_sdhci_var}, {}, }; MODULE_DEVICE_TABLE(of, sdhci_msm_dt_match); static const struct sdhci_ops sdhci_msm_ops = { .reset = sdhci_msm_reset, .set_clock = sdhci_msm_set_clock, .get_min_clock = sdhci_msm_get_min_clock, .get_max_clock = sdhci_msm_get_max_clock, .set_bus_width = sdhci_set_bus_width, .set_uhs_signaling = sdhci_msm_set_uhs_signaling, .write_w = sdhci_msm_writew, .write_b = sdhci_msm_writeb, .irq = sdhci_msm_cqe_irq, .dump_vendor_regs = sdhci_msm_dump_vendor_regs, .set_power = sdhci_set_power_noreg, .set_timeout = sdhci_msm_set_timeout, }; static const struct sdhci_pltfm_data sdhci_msm_pdata = { .quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION | SDHCI_QUIRK_SINGLE_POWER_WRITE | SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN | SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12, .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN, .ops = &sdhci_msm_ops, }; static inline void sdhci_msm_get_of_property(struct platform_device *pdev, struct sdhci_host *host) { struct device_node *node = pdev->dev.of_node; struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); if (of_property_read_u32(node, "qcom,ddr-config", &msm_host->ddr_config)) msm_host->ddr_config = DDR_CONFIG_POR_VAL; of_property_read_u32(node, "qcom,dll-config", &msm_host->dll_config); if (of_device_is_compatible(node, "qcom,msm8916-sdhci")) host->quirks2 |= SDHCI_QUIRK2_BROKEN_64_BIT_DMA; } static int sdhci_msm_gcc_reset(struct device *dev, struct sdhci_host *host) { struct reset_control *reset; int ret = 0; reset = reset_control_get_optional_exclusive(dev, NULL); if (IS_ERR(reset)) return dev_err_probe(dev, PTR_ERR(reset), "unable to acquire core_reset\n"); if (!reset) return ret; ret = reset_control_assert(reset); if (ret) { reset_control_put(reset); return dev_err_probe(dev, ret, "core_reset assert failed\n"); } /* * The hardware requirement for delay between assert/deassert * is at least 3-4 sleep clock (32.7KHz) cycles, which comes to * ~125us (4/32768). To be on the safe side add 200us delay. */ usleep_range(200, 210); ret = reset_control_deassert(reset); if (ret) { reset_control_put(reset); return dev_err_probe(dev, ret, "core_reset deassert failed\n"); } usleep_range(200, 210); reset_control_put(reset); return ret; } static int sdhci_msm_probe(struct platform_device *pdev) { struct sdhci_host *host; struct sdhci_pltfm_host *pltfm_host; struct sdhci_msm_host *msm_host; struct clk *clk; int ret; u16 host_version, core_minor; u32 core_version, config; u8 core_major; const struct sdhci_msm_offset *msm_offset; const struct sdhci_msm_variant_info *var_info; struct device_node *node = pdev->dev.of_node; host = sdhci_pltfm_init(pdev, &sdhci_msm_pdata, sizeof(*msm_host)); if (IS_ERR(host)) return PTR_ERR(host); host->sdma_boundary = 0; pltfm_host = sdhci_priv(host); msm_host = sdhci_pltfm_priv(pltfm_host); msm_host->mmc = host->mmc; msm_host->pdev = pdev; ret = mmc_of_parse(host->mmc); if (ret) goto pltfm_free; /* * Based on the compatible string, load the required msm host info from * the data associated with the version info. */ var_info = of_device_get_match_data(&pdev->dev); msm_host->mci_removed = var_info->mci_removed; msm_host->restore_dll_config = var_info->restore_dll_config; msm_host->var_ops = var_info->var_ops; msm_host->offset = var_info->offset; msm_host->uses_tassadar_dll = var_info->uses_tassadar_dll; msm_offset = msm_host->offset; sdhci_get_of_property(pdev); sdhci_msm_get_of_property(pdev, host); msm_host->saved_tuning_phase = INVALID_TUNING_PHASE; ret = sdhci_msm_gcc_reset(&pdev->dev, host); if (ret) goto pltfm_free; /* Setup SDCC bus voter clock. */ msm_host->bus_clk = devm_clk_get(&pdev->dev, "bus"); if (!IS_ERR(msm_host->bus_clk)) { /* Vote for max. clk rate for max. performance */ ret = clk_set_rate(msm_host->bus_clk, INT_MAX); if (ret) goto pltfm_free; ret = clk_prepare_enable(msm_host->bus_clk); if (ret) goto pltfm_free; } /* Setup main peripheral bus clock */ clk = devm_clk_get(&pdev->dev, "iface"); if (IS_ERR(clk)) { ret = PTR_ERR(clk); dev_err(&pdev->dev, "Peripheral clk setup failed (%d)\n", ret); goto bus_clk_disable; } msm_host->bulk_clks[1].clk = clk; /* Setup SDC MMC clock */ clk = devm_clk_get(&pdev->dev, "core"); if (IS_ERR(clk)) { ret = PTR_ERR(clk); dev_err(&pdev->dev, "SDC MMC clk setup failed (%d)\n", ret); goto bus_clk_disable; } msm_host->bulk_clks[0].clk = clk; /* Check for optional interconnect paths */ ret = dev_pm_opp_of_find_icc_paths(&pdev->dev, NULL); if (ret) goto bus_clk_disable; msm_host->opp_table = dev_pm_opp_set_clkname(&pdev->dev, "core"); if (IS_ERR(msm_host->opp_table)) { ret = PTR_ERR(msm_host->opp_table); goto bus_clk_disable; } /* OPP table is optional */ ret = dev_pm_opp_of_add_table(&pdev->dev); if (ret && ret != -ENODEV) { dev_err(&pdev->dev, "Invalid OPP table in Device tree\n"); goto opp_put_clkname; } /* Vote for maximum clock rate for maximum performance */ ret = dev_pm_opp_set_rate(&pdev->dev, INT_MAX); if (ret) dev_warn(&pdev->dev, "core clock boost failed\n"); clk = devm_clk_get(&pdev->dev, "cal"); if (IS_ERR(clk)) clk = NULL; msm_host->bulk_clks[2].clk = clk; clk = devm_clk_get(&pdev->dev, "sleep"); if (IS_ERR(clk)) clk = NULL; msm_host->bulk_clks[3].clk = clk; ret = clk_bulk_prepare_enable(ARRAY_SIZE(msm_host->bulk_clks), msm_host->bulk_clks); if (ret) goto opp_cleanup; /* * xo clock is needed for FLL feature of cm_dll. * In case if xo clock is not mentioned in DT, warn and proceed. */ msm_host->xo_clk = devm_clk_get(&pdev->dev, "xo"); if (IS_ERR(msm_host->xo_clk)) { ret = PTR_ERR(msm_host->xo_clk); dev_warn(&pdev->dev, "TCXO clk not present (%d)\n", ret); } if (!msm_host->mci_removed) { msm_host->core_mem = devm_platform_ioremap_resource(pdev, 1); if (IS_ERR(msm_host->core_mem)) { ret = PTR_ERR(msm_host->core_mem); goto clk_disable; } } /* Reset the vendor spec register to power on reset state */ writel_relaxed(CORE_VENDOR_SPEC_POR_VAL, host->ioaddr + msm_offset->core_vendor_spec); if (!msm_host->mci_removed) { /* Set HC_MODE_EN bit in HC_MODE register */ msm_host_writel(msm_host, HC_MODE_EN, host, msm_offset->core_hc_mode); config = msm_host_readl(msm_host, host, msm_offset->core_hc_mode); config |= FF_CLK_SW_RST_DIS; msm_host_writel(msm_host, config, host, msm_offset->core_hc_mode); } host_version = readw_relaxed((host->ioaddr + SDHCI_HOST_VERSION)); dev_dbg(&pdev->dev, "Host Version: 0x%x Vendor Version 0x%x\n", host_version, ((host_version & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT)); core_version = msm_host_readl(msm_host, host, msm_offset->core_mci_version); core_major = (core_version & CORE_VERSION_MAJOR_MASK) >> CORE_VERSION_MAJOR_SHIFT; core_minor = core_version & CORE_VERSION_MINOR_MASK; dev_dbg(&pdev->dev, "MCI Version: 0x%08x, major: 0x%04x, minor: 0x%02x\n", core_version, core_major, core_minor); if (core_major == 1 && core_minor >= 0x42) msm_host->use_14lpp_dll_reset = true; /* * SDCC 5 controller with major version 1, minor version 0x34 and later * with HS 400 mode support will use CM DLL instead of CDC LP 533 DLL. */ if (core_major == 1 && core_minor < 0x34) msm_host->use_cdclp533 = true; /* * Support for some capabilities is not advertised by newer * controller versions and must be explicitly enabled. */ if (core_major >= 1 && core_minor != 0x11 && core_minor != 0x12) { config = readl_relaxed(host->ioaddr + SDHCI_CAPABILITIES); config |= SDHCI_CAN_VDD_300 | SDHCI_CAN_DO_8BIT; writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec_capabilities0); } if (core_major == 1 && core_minor >= 0x49) msm_host->updated_ddr_cfg = true; ret = sdhci_msm_register_vreg(msm_host); if (ret) goto clk_disable; /* * Power on reset state may trigger power irq if previous status of * PWRCTL was either BUS_ON or IO_HIGH_V. So before enabling pwr irq * interrupt in GIC, any pending power irq interrupt should be * acknowledged. Otherwise power irq interrupt handler would be * fired prematurely. */ sdhci_msm_handle_pwr_irq(host, 0); /* * Ensure that above writes are propogated before interrupt enablement * in GIC. */ mb(); /* Setup IRQ for handling power/voltage tasks with PMIC */ msm_host->pwr_irq = platform_get_irq_byname(pdev, "pwr_irq"); if (msm_host->pwr_irq < 0) { ret = msm_host->pwr_irq; goto clk_disable; } sdhci_msm_init_pwr_irq_wait(msm_host); /* Enable pwr irq interrupts */ msm_host_writel(msm_host, INT_MASK, host, msm_offset->core_pwrctl_mask); ret = devm_request_threaded_irq(&pdev->dev, msm_host->pwr_irq, NULL, sdhci_msm_pwr_irq, IRQF_ONESHOT, dev_name(&pdev->dev), host); if (ret) { dev_err(&pdev->dev, "Request IRQ failed (%d)\n", ret); goto clk_disable; } msm_host->mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY | MMC_CAP_NEED_RSP_BUSY; pm_runtime_get_noresume(&pdev->dev); pm_runtime_set_active(&pdev->dev); pm_runtime_enable(&pdev->dev); pm_runtime_set_autosuspend_delay(&pdev->dev, MSM_MMC_AUTOSUSPEND_DELAY_MS); pm_runtime_use_autosuspend(&pdev->dev); host->mmc_host_ops.start_signal_voltage_switch = sdhci_msm_start_signal_voltage_switch; host->mmc_host_ops.execute_tuning = sdhci_msm_execute_tuning; if (of_property_read_bool(node, "supports-cqe")) ret = sdhci_msm_cqe_add_host(host, pdev); else ret = sdhci_add_host(host); if (ret) goto pm_runtime_disable; pm_runtime_mark_last_busy(&pdev->dev); pm_runtime_put_autosuspend(&pdev->dev); return 0; pm_runtime_disable: pm_runtime_disable(&pdev->dev); pm_runtime_set_suspended(&pdev->dev); pm_runtime_put_noidle(&pdev->dev); clk_disable: clk_bulk_disable_unprepare(ARRAY_SIZE(msm_host->bulk_clks), msm_host->bulk_clks); opp_cleanup: dev_pm_opp_of_remove_table(&pdev->dev); opp_put_clkname: dev_pm_opp_put_clkname(msm_host->opp_table); bus_clk_disable: if (!IS_ERR(msm_host->bus_clk)) clk_disable_unprepare(msm_host->bus_clk); pltfm_free: sdhci_pltfm_free(pdev); return ret; } static int sdhci_msm_remove(struct platform_device *pdev) { struct sdhci_host *host = platform_get_drvdata(pdev); struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); int dead = (readl_relaxed(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff); sdhci_remove_host(host, dead); dev_pm_opp_of_remove_table(&pdev->dev); dev_pm_opp_put_clkname(msm_host->opp_table); pm_runtime_get_sync(&pdev->dev); pm_runtime_disable(&pdev->dev); pm_runtime_put_noidle(&pdev->dev); clk_bulk_disable_unprepare(ARRAY_SIZE(msm_host->bulk_clks), msm_host->bulk_clks); if (!IS_ERR(msm_host->bus_clk)) clk_disable_unprepare(msm_host->bus_clk); sdhci_pltfm_free(pdev); return 0; } static __maybe_unused int sdhci_msm_runtime_suspend(struct device *dev) { struct sdhci_host *host = dev_get_drvdata(dev); struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); /* Drop the performance vote */ dev_pm_opp_set_rate(dev, 0); clk_bulk_disable_unprepare(ARRAY_SIZE(msm_host->bulk_clks), msm_host->bulk_clks); return 0; } static __maybe_unused int sdhci_msm_runtime_resume(struct device *dev) { struct sdhci_host *host = dev_get_drvdata(dev); struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); int ret; ret = clk_bulk_prepare_enable(ARRAY_SIZE(msm_host->bulk_clks), msm_host->bulk_clks); if (ret) return ret; /* * Whenever core-clock is gated dynamically, it's needed to * restore the SDR DLL settings when the clock is ungated. */ if (msm_host->restore_dll_config && msm_host->clk_rate) ret = sdhci_msm_restore_sdr_dll_config(host); dev_pm_opp_set_rate(dev, msm_host->clk_rate); return ret; } static const struct dev_pm_ops sdhci_msm_pm_ops = { SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, pm_runtime_force_resume) SET_RUNTIME_PM_OPS(sdhci_msm_runtime_suspend, sdhci_msm_runtime_resume, NULL) }; static struct platform_driver sdhci_msm_driver = { .probe = sdhci_msm_probe, .remove = sdhci_msm_remove, .driver = { .name = "sdhci_msm", .of_match_table = sdhci_msm_dt_match, .pm = &sdhci_msm_pm_ops, .probe_type = PROBE_PREFER_ASYNCHRONOUS, }, }; module_platform_driver(sdhci_msm_driver); MODULE_DESCRIPTION("Qualcomm Secure Digital Host Controller Interface driver"); MODULE_LICENSE("GPL v2");