// SPDX-License-Identifier: GPL-1.0+ /* * Open Host Controller Interface (OHCI) driver for USB. * * Maintainer: Alan Stern * * (C) Copyright 1999 Roman Weissgaerber * (C) Copyright 2000-2004 David Brownell * * [ Initialisation is based on Linus' ] * [ uhci code and gregs ohci fragments ] * [ (C) Copyright 1999 Linus Torvalds ] * [ (C) Copyright 1999 Gregory P. Smith] * * * OHCI is the main "non-Intel/VIA" standard for USB 1.1 host controller * interfaces (though some non-x86 Intel chips use it). It supports * smarter hardware than UHCI. A download link for the spec available * through the https://www.usb.org website. * * This file is licenced under the GPL. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #define DRIVER_AUTHOR "Roman Weissgaerber, David Brownell" #define DRIVER_DESC "USB 1.1 'Open' Host Controller (OHCI) Driver" /*-------------------------------------------------------------------------*/ /* For initializing controller (mask in an HCFS mode too) */ #define OHCI_CONTROL_INIT OHCI_CTRL_CBSR #define OHCI_INTR_INIT \ (OHCI_INTR_MIE | OHCI_INTR_RHSC | OHCI_INTR_UE \ | OHCI_INTR_RD | OHCI_INTR_WDH) #ifdef __hppa__ /* On PA-RISC, PDC can leave IR set incorrectly; ignore it there. */ #define IR_DISABLE #endif #ifdef CONFIG_ARCH_OMAP /* OMAP doesn't support IR (no SMM; not needed) */ #define IR_DISABLE #endif /*-------------------------------------------------------------------------*/ static const char hcd_name [] = "ohci_hcd"; #define STATECHANGE_DELAY msecs_to_jiffies(300) #define IO_WATCHDOG_DELAY msecs_to_jiffies(275) #define IO_WATCHDOG_OFF 0xffffff00 #include "ohci.h" #include "pci-quirks.h" static void ohci_dump(struct ohci_hcd *ohci); static void ohci_stop(struct usb_hcd *hcd); static void io_watchdog_func(struct timer_list *t); #include "ohci-hub.c" #include "ohci-dbg.c" #include "ohci-mem.c" #include "ohci-q.c" /* * On architectures with edge-triggered interrupts we must never return * IRQ_NONE. */ #if defined(CONFIG_SA1111) /* ... or other edge-triggered systems */ #define IRQ_NOTMINE IRQ_HANDLED #else #define IRQ_NOTMINE IRQ_NONE #endif /* Some boards misreport power switching/overcurrent */ static bool distrust_firmware; module_param (distrust_firmware, bool, 0); MODULE_PARM_DESC (distrust_firmware, "true to distrust firmware power/overcurrent setup"); /* Some boards leave IR set wrongly, since they fail BIOS/SMM handshakes */ static bool no_handshake; module_param (no_handshake, bool, 0); MODULE_PARM_DESC (no_handshake, "true (not default) disables BIOS handshake"); /*-------------------------------------------------------------------------*/ static int number_of_tds(struct urb *urb) { int len, i, num, this_sg_len; struct scatterlist *sg; len = urb->transfer_buffer_length; i = urb->num_mapped_sgs; if (len > 0 && i > 0) { /* Scatter-gather transfer */ num = 0; sg = urb->sg; for (;;) { this_sg_len = min_t(int, sg_dma_len(sg), len); num += DIV_ROUND_UP(this_sg_len, 4096); len -= this_sg_len; if (--i <= 0 || len <= 0) break; sg = sg_next(sg); } } else { /* Non-SG transfer */ /* one TD for every 4096 Bytes (could be up to 8K) */ num = DIV_ROUND_UP(len, 4096); } return num; } /* * queue up an urb for anything except the root hub */ static int ohci_urb_enqueue ( struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags ) { struct ohci_hcd *ohci = hcd_to_ohci (hcd); struct ed *ed; urb_priv_t *urb_priv; unsigned int pipe = urb->pipe; int i, size = 0; unsigned long flags; int retval = 0; /* every endpoint has a ed, locate and maybe (re)initialize it */ ed = ed_get(ohci, urb->ep, urb->dev, pipe, urb->interval); if (! ed) return -ENOMEM; /* for the private part of the URB we need the number of TDs (size) */ switch (ed->type) { case PIPE_CONTROL: /* td_submit_urb() doesn't yet handle these */ if (urb->transfer_buffer_length > 4096) return -EMSGSIZE; /* 1 TD for setup, 1 for ACK, plus ... */ size = 2; /* FALLTHROUGH */ // case PIPE_INTERRUPT: // case PIPE_BULK: default: size += number_of_tds(urb); /* maybe a zero-length packet to wrap it up */ if (size == 0) size++; else if ((urb->transfer_flags & URB_ZERO_PACKET) != 0 && (urb->transfer_buffer_length % usb_maxpacket (urb->dev, pipe, usb_pipeout (pipe))) == 0) size++; break; case PIPE_ISOCHRONOUS: /* number of packets from URB */ size = urb->number_of_packets; break; } /* allocate the private part of the URB */ urb_priv = kzalloc (sizeof (urb_priv_t) + size * sizeof (struct td *), mem_flags); if (!urb_priv) return -ENOMEM; INIT_LIST_HEAD (&urb_priv->pending); urb_priv->length = size; urb_priv->ed = ed; /* allocate the TDs (deferring hash chain updates) */ for (i = 0; i < size; i++) { urb_priv->td [i] = td_alloc (ohci, mem_flags); if (!urb_priv->td [i]) { urb_priv->length = i; urb_free_priv (ohci, urb_priv); return -ENOMEM; } } spin_lock_irqsave (&ohci->lock, flags); /* don't submit to a dead HC */ if (!HCD_HW_ACCESSIBLE(hcd)) { retval = -ENODEV; goto fail; } if (ohci->rh_state != OHCI_RH_RUNNING) { retval = -ENODEV; goto fail; } retval = usb_hcd_link_urb_to_ep(hcd, urb); if (retval) goto fail; /* schedule the ed if needed */ if (ed->state == ED_IDLE) { retval = ed_schedule (ohci, ed); if (retval < 0) { usb_hcd_unlink_urb_from_ep(hcd, urb); goto fail; } /* Start up the I/O watchdog timer, if it's not running */ if (ohci->prev_frame_no == IO_WATCHDOG_OFF && list_empty(&ohci->eds_in_use) && !(ohci->flags & OHCI_QUIRK_QEMU)) { ohci->prev_frame_no = ohci_frame_no(ohci); mod_timer(&ohci->io_watchdog, jiffies + IO_WATCHDOG_DELAY); } list_add(&ed->in_use_list, &ohci->eds_in_use); if (ed->type == PIPE_ISOCHRONOUS) { u16 frame = ohci_frame_no(ohci); /* delay a few frames before the first TD */ frame += max_t (u16, 8, ed->interval); frame &= ~(ed->interval - 1); frame |= ed->branch; urb->start_frame = frame; ed->last_iso = frame + ed->interval * (size - 1); } } else if (ed->type == PIPE_ISOCHRONOUS) { u16 next = ohci_frame_no(ohci) + 1; u16 frame = ed->last_iso + ed->interval; u16 length = ed->interval * (size - 1); /* Behind the scheduling threshold? */ if (unlikely(tick_before(frame, next))) { /* URB_ISO_ASAP: Round up to the first available slot */ if (urb->transfer_flags & URB_ISO_ASAP) { frame += (next - frame + ed->interval - 1) & -ed->interval; /* * Not ASAP: Use the next slot in the stream, * no matter what. */ } else { /* * Some OHCI hardware doesn't handle late TDs * correctly. After retiring them it proceeds * to the next ED instead of the next TD. * Therefore we have to omit the late TDs * entirely. */ urb_priv->td_cnt = DIV_ROUND_UP( (u16) (next - frame), ed->interval); if (urb_priv->td_cnt >= urb_priv->length) { ++urb_priv->td_cnt; /* Mark it */ ohci_dbg(ohci, "iso underrun %p (%u+%u < %u)\n", urb, frame, length, next); } } } urb->start_frame = frame; ed->last_iso = frame + length; } /* fill the TDs and link them to the ed; and * enable that part of the schedule, if needed * and update count of queued periodic urbs */ urb->hcpriv = urb_priv; td_submit_urb (ohci, urb); fail: if (retval) urb_free_priv (ohci, urb_priv); spin_unlock_irqrestore (&ohci->lock, flags); return retval; } /* * decouple the URB from the HC queues (TDs, urb_priv). * reporting is always done * asynchronously, and we might be dealing with an urb that's * partially transferred, or an ED with other urbs being unlinked. */ static int ohci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status) { struct ohci_hcd *ohci = hcd_to_ohci (hcd); unsigned long flags; int rc; urb_priv_t *urb_priv; spin_lock_irqsave (&ohci->lock, flags); rc = usb_hcd_check_unlink_urb(hcd, urb, status); if (rc == 0) { /* Unless an IRQ completed the unlink while it was being * handed to us, flag it for unlink and giveback, and force * some upcoming INTR_SF to call finish_unlinks() */ urb_priv = urb->hcpriv; if (urb_priv->ed->state == ED_OPER) start_ed_unlink(ohci, urb_priv->ed); if (ohci->rh_state != OHCI_RH_RUNNING) { /* With HC dead, we can clean up right away */ ohci_work(ohci); } } spin_unlock_irqrestore (&ohci->lock, flags); return rc; } /*-------------------------------------------------------------------------*/ /* frees config/altsetting state for endpoints, * including ED memory, dummy TD, and bulk/intr data toggle */ static void ohci_endpoint_disable (struct usb_hcd *hcd, struct usb_host_endpoint *ep) { struct ohci_hcd *ohci = hcd_to_ohci (hcd); unsigned long flags; struct ed *ed = ep->hcpriv; unsigned limit = 1000; /* ASSERT: any requests/urbs are being unlinked */ /* ASSERT: nobody can be submitting urbs for this any more */ if (!ed) return; rescan: spin_lock_irqsave (&ohci->lock, flags); if (ohci->rh_state != OHCI_RH_RUNNING) { sanitize: ed->state = ED_IDLE; ohci_work(ohci); } switch (ed->state) { case ED_UNLINK: /* wait for hw to finish? */ /* major IRQ delivery trouble loses INTR_SF too... */ if (limit-- == 0) { ohci_warn(ohci, "ED unlink timeout\n"); goto sanitize; } spin_unlock_irqrestore (&ohci->lock, flags); schedule_timeout_uninterruptible(1); goto rescan; case ED_IDLE: /* fully unlinked */ if (list_empty (&ed->td_list)) { td_free (ohci, ed->dummy); ed_free (ohci, ed); break; } fallthrough; default: /* caller was supposed to have unlinked any requests; * that's not our job. can't recover; must leak ed. */ ohci_err (ohci, "leak ed %p (#%02x) state %d%s\n", ed, ep->desc.bEndpointAddress, ed->state, list_empty (&ed->td_list) ? "" : " (has tds)"); td_free (ohci, ed->dummy); break; } ep->hcpriv = NULL; spin_unlock_irqrestore (&ohci->lock, flags); } static int ohci_get_frame (struct usb_hcd *hcd) { struct ohci_hcd *ohci = hcd_to_ohci (hcd); return ohci_frame_no(ohci); } static void ohci_usb_reset (struct ohci_hcd *ohci) { ohci->hc_control = ohci_readl (ohci, &ohci->regs->control); ohci->hc_control &= OHCI_CTRL_RWC; ohci_writel (ohci, ohci->hc_control, &ohci->regs->control); ohci->rh_state = OHCI_RH_HALTED; } /* ohci_shutdown forcibly disables IRQs and DMA, helping kexec and * other cases where the next software may expect clean state from the * "firmware". this is bus-neutral, unlike shutdown() methods. */ static void _ohci_shutdown(struct usb_hcd *hcd) { struct ohci_hcd *ohci; ohci = hcd_to_ohci (hcd); ohci_writel(ohci, (u32) ~0, &ohci->regs->intrdisable); /* Software reset, after which the controller goes into SUSPEND */ ohci_writel(ohci, OHCI_HCR, &ohci->regs->cmdstatus); ohci_readl(ohci, &ohci->regs->cmdstatus); /* flush the writes */ udelay(10); ohci_writel(ohci, ohci->fminterval, &ohci->regs->fminterval); ohci->rh_state = OHCI_RH_HALTED; } static void ohci_shutdown(struct usb_hcd *hcd) { struct ohci_hcd *ohci = hcd_to_ohci(hcd); unsigned long flags; spin_lock_irqsave(&ohci->lock, flags); _ohci_shutdown(hcd); spin_unlock_irqrestore(&ohci->lock, flags); } /*-------------------------------------------------------------------------* * HC functions *-------------------------------------------------------------------------*/ /* init memory, and kick BIOS/SMM off */ static int ohci_init (struct ohci_hcd *ohci) { int ret; struct usb_hcd *hcd = ohci_to_hcd(ohci); /* Accept arbitrarily long scatter-gather lists */ if (!hcd->localmem_pool) hcd->self.sg_tablesize = ~0; if (distrust_firmware) ohci->flags |= OHCI_QUIRK_HUB_POWER; ohci->rh_state = OHCI_RH_HALTED; ohci->regs = hcd->regs; /* REVISIT this BIOS handshake is now moved into PCI "quirks", and * was never needed for most non-PCI systems ... remove the code? */ #ifndef IR_DISABLE /* SMM owns the HC? not for long! */ if (!no_handshake && ohci_readl (ohci, &ohci->regs->control) & OHCI_CTRL_IR) { u32 temp; ohci_dbg (ohci, "USB HC TakeOver from BIOS/SMM\n"); /* this timeout is arbitrary. we make it long, so systems * depending on usb keyboards may be usable even if the * BIOS/SMM code seems pretty broken. */ temp = 500; /* arbitrary: five seconds */ ohci_writel (ohci, OHCI_INTR_OC, &ohci->regs->intrenable); ohci_writel (ohci, OHCI_OCR, &ohci->regs->cmdstatus); while (ohci_readl (ohci, &ohci->regs->control) & OHCI_CTRL_IR) { msleep (10); if (--temp == 0) { ohci_err (ohci, "USB HC takeover failed!" " (BIOS/SMM bug)\n"); return -EBUSY; } } ohci_usb_reset (ohci); } #endif /* Disable HC interrupts */ ohci_writel (ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable); /* flush the writes, and save key bits like RWC */ if (ohci_readl (ohci, &ohci->regs->control) & OHCI_CTRL_RWC) ohci->hc_control |= OHCI_CTRL_RWC; /* Read the number of ports unless overridden */ if (ohci->num_ports == 0) ohci->num_ports = roothub_a(ohci) & RH_A_NDP; if (ohci->hcca) return 0; timer_setup(&ohci->io_watchdog, io_watchdog_func, 0); ohci->prev_frame_no = IO_WATCHDOG_OFF; if (hcd->localmem_pool) ohci->hcca = gen_pool_dma_alloc_align(hcd->localmem_pool, sizeof(*ohci->hcca), &ohci->hcca_dma, 256); else ohci->hcca = dma_alloc_coherent(hcd->self.controller, sizeof(*ohci->hcca), &ohci->hcca_dma, GFP_KERNEL); if (!ohci->hcca) return -ENOMEM; if ((ret = ohci_mem_init (ohci)) < 0) ohci_stop (hcd); else { create_debug_files (ohci); } return ret; } /*-------------------------------------------------------------------------*/ /* Start an OHCI controller, set the BUS operational * resets USB and controller * enable interrupts */ static int ohci_run (struct ohci_hcd *ohci) { u32 mask, val; int first = ohci->fminterval == 0; struct usb_hcd *hcd = ohci_to_hcd(ohci); ohci->rh_state = OHCI_RH_HALTED; /* boot firmware should have set this up (5.1.1.3.1) */ if (first) { val = ohci_readl (ohci, &ohci->regs->fminterval); ohci->fminterval = val & 0x3fff; if (ohci->fminterval != FI) ohci_dbg (ohci, "fminterval delta %d\n", ohci->fminterval - FI); ohci->fminterval |= FSMP (ohci->fminterval) << 16; /* also: power/overcurrent flags in roothub.a */ } /* Reset USB nearly "by the book". RemoteWakeupConnected has * to be checked in case boot firmware (BIOS/SMM/...) has set up * wakeup in a way the bus isn't aware of (e.g., legacy PCI PM). * If the bus glue detected wakeup capability then it should * already be enabled; if so we'll just enable it again. */ if ((ohci->hc_control & OHCI_CTRL_RWC) != 0) device_set_wakeup_capable(hcd->self.controller, 1); switch (ohci->hc_control & OHCI_CTRL_HCFS) { case OHCI_USB_OPER: val = 0; break; case OHCI_USB_SUSPEND: case OHCI_USB_RESUME: ohci->hc_control &= OHCI_CTRL_RWC; ohci->hc_control |= OHCI_USB_RESUME; val = 10 /* msec wait */; break; // case OHCI_USB_RESET: default: ohci->hc_control &= OHCI_CTRL_RWC; ohci->hc_control |= OHCI_USB_RESET; val = 50 /* msec wait */; break; } ohci_writel (ohci, ohci->hc_control, &ohci->regs->control); // flush the writes (void) ohci_readl (ohci, &ohci->regs->control); msleep(val); memset (ohci->hcca, 0, sizeof (struct ohci_hcca)); /* 2msec timelimit here means no irqs/preempt */ spin_lock_irq (&ohci->lock); retry: /* HC Reset requires max 10 us delay */ ohci_writel (ohci, OHCI_HCR, &ohci->regs->cmdstatus); val = 30; /* ... allow extra time */ while ((ohci_readl (ohci, &ohci->regs->cmdstatus) & OHCI_HCR) != 0) { if (--val == 0) { spin_unlock_irq (&ohci->lock); ohci_err (ohci, "USB HC reset timed out!\n"); return -1; } udelay (1); } /* now we're in the SUSPEND state ... must go OPERATIONAL * within 2msec else HC enters RESUME * * ... but some hardware won't init fmInterval "by the book" * (SiS, OPTi ...), so reset again instead. SiS doesn't need * this if we write fmInterval after we're OPERATIONAL. * Unclear about ALi, ServerWorks, and others ... this could * easily be a longstanding bug in chip init on Linux. */ if (ohci->flags & OHCI_QUIRK_INITRESET) { ohci_writel (ohci, ohci->hc_control, &ohci->regs->control); // flush those writes (void) ohci_readl (ohci, &ohci->regs->control); } /* Tell the controller where the control and bulk lists are * The lists are empty now. */ ohci_writel (ohci, 0, &ohci->regs->ed_controlhead); ohci_writel (ohci, 0, &ohci->regs->ed_bulkhead); /* a reset clears this */ ohci_writel (ohci, (u32) ohci->hcca_dma, &ohci->regs->hcca); periodic_reinit (ohci); /* some OHCI implementations are finicky about how they init. * bogus values here mean not even enumeration could work. */ if ((ohci_readl (ohci, &ohci->regs->fminterval) & 0x3fff0000) == 0 || !ohci_readl (ohci, &ohci->regs->periodicstart)) { if (!(ohci->flags & OHCI_QUIRK_INITRESET)) { ohci->flags |= OHCI_QUIRK_INITRESET; ohci_dbg (ohci, "enabling initreset quirk\n"); goto retry; } spin_unlock_irq (&ohci->lock); ohci_err (ohci, "init err (%08x %04x)\n", ohci_readl (ohci, &ohci->regs->fminterval), ohci_readl (ohci, &ohci->regs->periodicstart)); return -EOVERFLOW; } /* use rhsc irqs after hub_wq is allocated */ set_bit(HCD_FLAG_POLL_RH, &hcd->flags); hcd->uses_new_polling = 1; /* start controller operations */ ohci->hc_control &= OHCI_CTRL_RWC; ohci->hc_control |= OHCI_CONTROL_INIT | OHCI_USB_OPER; ohci_writel (ohci, ohci->hc_control, &ohci->regs->control); ohci->rh_state = OHCI_RH_RUNNING; /* wake on ConnectStatusChange, matching external hubs */ ohci_writel (ohci, RH_HS_DRWE, &ohci->regs->roothub.status); /* Choose the interrupts we care about now, others later on demand */ mask = OHCI_INTR_INIT; ohci_writel (ohci, ~0, &ohci->regs->intrstatus); ohci_writel (ohci, mask, &ohci->regs->intrenable); /* handle root hub init quirks ... */ val = roothub_a (ohci); /* Configure for per-port over-current protection by default */ val &= ~RH_A_NOCP; val |= RH_A_OCPM; if (ohci->flags & OHCI_QUIRK_SUPERIO) { /* NSC 87560 and maybe others. * Ganged power switching, no over-current protection. */ val |= RH_A_NOCP; val &= ~(RH_A_POTPGT | RH_A_NPS | RH_A_PSM | RH_A_OCPM); } else if ((ohci->flags & OHCI_QUIRK_AMD756) || (ohci->flags & OHCI_QUIRK_HUB_POWER)) { /* hub power always on; required for AMD-756 and some * Mac platforms. */ val |= RH_A_NPS; } ohci_writel(ohci, val, &ohci->regs->roothub.a); ohci_writel (ohci, RH_HS_LPSC, &ohci->regs->roothub.status); ohci_writel (ohci, (val & RH_A_NPS) ? 0 : RH_B_PPCM, &ohci->regs->roothub.b); // flush those writes (void) ohci_readl (ohci, &ohci->regs->control); ohci->next_statechange = jiffies + STATECHANGE_DELAY; spin_unlock_irq (&ohci->lock); // POTPGT delay is bits 24-31, in 2 ms units. mdelay ((val >> 23) & 0x1fe); ohci_dump(ohci); return 0; } /* ohci_setup routine for generic controller initialization */ int ohci_setup(struct usb_hcd *hcd) { struct ohci_hcd *ohci = hcd_to_ohci(hcd); ohci_hcd_init(ohci); return ohci_init(ohci); } EXPORT_SYMBOL_GPL(ohci_setup); /* ohci_start routine for generic controller start of all OHCI bus glue */ static int ohci_start(struct usb_hcd *hcd) { struct ohci_hcd *ohci = hcd_to_ohci(hcd); int ret; ret = ohci_run(ohci); if (ret < 0) { ohci_err(ohci, "can't start\n"); ohci_stop(hcd); } return ret; } /*-------------------------------------------------------------------------*/ /* * Some OHCI controllers are known to lose track of completed TDs. They * don't add the TDs to the hardware done queue, which means we never see * them as being completed. * * This watchdog routine checks for such problems. Without some way to * tell when those TDs have completed, we would never take their EDs off * the unlink list. As a result, URBs could never be dequeued and * endpoints could never be released. */ static void io_watchdog_func(struct timer_list *t) { struct ohci_hcd *ohci = from_timer(ohci, t, io_watchdog); bool takeback_all_pending = false; u32 status; u32 head; struct ed *ed; struct td *td, *td_start, *td_next; unsigned frame_no, prev_frame_no = IO_WATCHDOG_OFF; unsigned long flags; spin_lock_irqsave(&ohci->lock, flags); /* * One way to lose track of completed TDs is if the controller * never writes back the done queue head. If it hasn't been * written back since the last time this function ran and if it * was non-empty at that time, something is badly wrong with the * hardware. */ status = ohci_readl(ohci, &ohci->regs->intrstatus); if (!(status & OHCI_INTR_WDH) && ohci->wdh_cnt == ohci->prev_wdh_cnt) { if (ohci->prev_donehead) { ohci_err(ohci, "HcDoneHead not written back; disabled\n"); died: usb_hc_died(ohci_to_hcd(ohci)); ohci_dump(ohci); _ohci_shutdown(ohci_to_hcd(ohci)); goto done; } else { /* No write back because the done queue was empty */ takeback_all_pending = true; } } /* Check every ED which might have pending TDs */ list_for_each_entry(ed, &ohci->eds_in_use, in_use_list) { if (ed->pending_td) { if (takeback_all_pending || OKAY_TO_TAKEBACK(ohci, ed)) { unsigned tmp = hc32_to_cpu(ohci, ed->hwINFO); ohci_dbg(ohci, "takeback pending TD for dev %d ep 0x%x\n", 0x007f & tmp, (0x000f & (tmp >> 7)) + ((tmp & ED_IN) >> 5)); add_to_done_list(ohci, ed->pending_td); } } /* Starting from the latest pending TD, */ td = ed->pending_td; /* or the last TD on the done list, */ if (!td) { list_for_each_entry(td_next, &ed->td_list, td_list) { if (!td_next->next_dl_td) break; td = td_next; } } /* find the last TD processed by the controller. */ head = hc32_to_cpu(ohci, READ_ONCE(ed->hwHeadP)) & TD_MASK; td_start = td; td_next = list_prepare_entry(td, &ed->td_list, td_list); list_for_each_entry_continue(td_next, &ed->td_list, td_list) { if (head == (u32) td_next->td_dma) break; td = td_next; /* head pointer has passed this TD */ } if (td != td_start) { /* * In case a WDH cycle is in progress, we will wait * for the next two cycles to complete before assuming * this TD will never get on the done queue. */ ed->takeback_wdh_cnt = ohci->wdh_cnt + 2; ed->pending_td = td; } } ohci_work(ohci); if (ohci->rh_state == OHCI_RH_RUNNING) { /* * Sometimes a controller just stops working. We can tell * by checking that the frame counter has advanced since * the last time we ran. * * But be careful: Some controllers violate the spec by * stopping their frame counter when no ports are active. */ frame_no = ohci_frame_no(ohci); if (frame_no == ohci->prev_frame_no) { int active_cnt = 0; int i; unsigned tmp; for (i = 0; i < ohci->num_ports; ++i) { tmp = roothub_portstatus(ohci, i); /* Enabled and not suspended? */ if ((tmp & RH_PS_PES) && !(tmp & RH_PS_PSS)) ++active_cnt; } if (active_cnt > 0) { ohci_err(ohci, "frame counter not updating; disabled\n"); goto died; } } if (!list_empty(&ohci->eds_in_use)) { prev_frame_no = frame_no; ohci->prev_wdh_cnt = ohci->wdh_cnt; ohci->prev_donehead = ohci_readl(ohci, &ohci->regs->donehead); mod_timer(&ohci->io_watchdog, jiffies + IO_WATCHDOG_DELAY); } } done: ohci->prev_frame_no = prev_frame_no; spin_unlock_irqrestore(&ohci->lock, flags); } /* an interrupt happens */ static irqreturn_t ohci_irq (struct usb_hcd *hcd) { struct ohci_hcd *ohci = hcd_to_ohci (hcd); struct ohci_regs __iomem *regs = ohci->regs; int ints; /* Read interrupt status (and flush pending writes). We ignore the * optimization of checking the LSB of hcca->done_head; it doesn't * work on all systems (edge triggering for OHCI can be a factor). */ ints = ohci_readl(ohci, ®s->intrstatus); /* Check for an all 1's result which is a typical consequence * of dead, unclocked, or unplugged (CardBus...) devices */ again: if (ints == ~(u32)0) { ohci->rh_state = OHCI_RH_HALTED; ohci_dbg (ohci, "device removed!\n"); usb_hc_died(hcd); return IRQ_HANDLED; } /* We only care about interrupts that are enabled */ ints &= ohci_readl(ohci, ®s->intrenable); /* interrupt for some other device? */ if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED)) return IRQ_NOTMINE; if (ints & OHCI_INTR_UE) { // e.g. due to PCI Master/Target Abort if (quirk_nec(ohci)) { /* Workaround for a silicon bug in some NEC chips used * in Apple's PowerBooks. Adapted from Darwin code. */ ohci_err (ohci, "OHCI Unrecoverable Error, scheduling NEC chip restart\n"); ohci_writel (ohci, OHCI_INTR_UE, ®s->intrdisable); schedule_work (&ohci->nec_work); } else { ohci_err (ohci, "OHCI Unrecoverable Error, disabled\n"); ohci->rh_state = OHCI_RH_HALTED; usb_hc_died(hcd); } ohci_dump(ohci); ohci_usb_reset (ohci); } if (ints & OHCI_INTR_RHSC) { ohci_dbg(ohci, "rhsc\n"); ohci->next_statechange = jiffies + STATECHANGE_DELAY; ohci_writel(ohci, OHCI_INTR_RD | OHCI_INTR_RHSC, ®s->intrstatus); /* NOTE: Vendors didn't always make the same implementation * choices for RHSC. Many followed the spec; RHSC triggers * on an edge, like setting and maybe clearing a port status * change bit. With others it's level-triggered, active * until hub_wq clears all the port status change bits. We'll * always disable it here and rely on polling until hub_wq * re-enables it. */ ohci_writel(ohci, OHCI_INTR_RHSC, ®s->intrdisable); usb_hcd_poll_rh_status(hcd); } /* For connect and disconnect events, we expect the controller * to turn on RHSC along with RD. But for remote wakeup events * this might not happen. */ else if (ints & OHCI_INTR_RD) { ohci_dbg(ohci, "resume detect\n"); ohci_writel(ohci, OHCI_INTR_RD, ®s->intrstatus); set_bit(HCD_FLAG_POLL_RH, &hcd->flags); if (ohci->autostop) { spin_lock (&ohci->lock); ohci_rh_resume (ohci); spin_unlock (&ohci->lock); } else usb_hcd_resume_root_hub(hcd); } spin_lock(&ohci->lock); if (ints & OHCI_INTR_WDH) update_done_list(ohci); /* could track INTR_SO to reduce available PCI/... bandwidth */ /* handle any pending URB/ED unlinks, leaving INTR_SF enabled * when there's still unlinking to be done (next frame). */ ohci_work(ohci); if ((ints & OHCI_INTR_SF) != 0 && !ohci->ed_rm_list && ohci->rh_state == OHCI_RH_RUNNING) ohci_writel (ohci, OHCI_INTR_SF, ®s->intrdisable); if (ohci->rh_state == OHCI_RH_RUNNING) { ohci_writel (ohci, ints, ®s->intrstatus); if (ints & OHCI_INTR_WDH) ++ohci->wdh_cnt; ohci_writel (ohci, OHCI_INTR_MIE, ®s->intrenable); // flush those writes (void) ohci_readl (ohci, &ohci->regs->control); } spin_unlock(&ohci->lock); /* repeat until all enabled interrupts are handled */ if (ohci->rh_state != OHCI_RH_HALTED) { ints = ohci_readl(ohci, ®s->intrstatus); if (ints && (ints & ohci_readl(ohci, ®s->intrenable))) goto again; } return IRQ_HANDLED; } /*-------------------------------------------------------------------------*/ static void ohci_stop (struct usb_hcd *hcd) { struct ohci_hcd *ohci = hcd_to_ohci (hcd); ohci_dump(ohci); if (quirk_nec(ohci)) flush_work(&ohci->nec_work); del_timer_sync(&ohci->io_watchdog); ohci->prev_frame_no = IO_WATCHDOG_OFF; ohci_writel (ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable); ohci_usb_reset(ohci); free_irq(hcd->irq, hcd); hcd->irq = 0; if (quirk_amdiso(ohci)) usb_amd_dev_put(); remove_debug_files (ohci); ohci_mem_cleanup (ohci); if (ohci->hcca) { if (hcd->localmem_pool) gen_pool_free(hcd->localmem_pool, (unsigned long)ohci->hcca, sizeof(*ohci->hcca)); else dma_free_coherent(hcd->self.controller, sizeof(*ohci->hcca), ohci->hcca, ohci->hcca_dma); ohci->hcca = NULL; ohci->hcca_dma = 0; } } /*-------------------------------------------------------------------------*/ #if defined(CONFIG_PM) || defined(CONFIG_USB_PCI) /* must not be called from interrupt context */ int ohci_restart(struct ohci_hcd *ohci) { int temp; int i; struct urb_priv *priv; ohci_init(ohci); spin_lock_irq(&ohci->lock); ohci->rh_state = OHCI_RH_HALTED; /* Recycle any "live" eds/tds (and urbs). */ if (!list_empty (&ohci->pending)) ohci_dbg(ohci, "abort schedule...\n"); list_for_each_entry (priv, &ohci->pending, pending) { struct urb *urb = priv->td[0]->urb; struct ed *ed = priv->ed; switch (ed->state) { case ED_OPER: ed->state = ED_UNLINK; ed->hwINFO |= cpu_to_hc32(ohci, ED_DEQUEUE); ed_deschedule (ohci, ed); ed->ed_next = ohci->ed_rm_list; ed->ed_prev = NULL; ohci->ed_rm_list = ed; fallthrough; case ED_UNLINK: break; default: ohci_dbg(ohci, "bogus ed %p state %d\n", ed, ed->state); } if (!urb->unlinked) urb->unlinked = -ESHUTDOWN; } ohci_work(ohci); spin_unlock_irq(&ohci->lock); /* paranoia, in case that didn't work: */ /* empty the interrupt branches */ for (i = 0; i < NUM_INTS; i++) ohci->load [i] = 0; for (i = 0; i < NUM_INTS; i++) ohci->hcca->int_table [i] = 0; /* no EDs to remove */ ohci->ed_rm_list = NULL; /* empty control and bulk lists */ ohci->ed_controltail = NULL; ohci->ed_bulktail = NULL; if ((temp = ohci_run (ohci)) < 0) { ohci_err (ohci, "can't restart, %d\n", temp); return temp; } ohci_dbg(ohci, "restart complete\n"); return 0; } EXPORT_SYMBOL_GPL(ohci_restart); #endif #ifdef CONFIG_PM int ohci_suspend(struct usb_hcd *hcd, bool do_wakeup) { struct ohci_hcd *ohci = hcd_to_ohci (hcd); unsigned long flags; int rc = 0; /* Disable irq emission and mark HW unaccessible. Use * the spinlock to properly synchronize with possible pending * RH suspend or resume activity. */ spin_lock_irqsave (&ohci->lock, flags); ohci_writel(ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable); (void)ohci_readl(ohci, &ohci->regs->intrdisable); clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); spin_unlock_irqrestore (&ohci->lock, flags); synchronize_irq(hcd->irq); if (do_wakeup && HCD_WAKEUP_PENDING(hcd)) { ohci_resume(hcd, false); rc = -EBUSY; } return rc; } EXPORT_SYMBOL_GPL(ohci_suspend); int ohci_resume(struct usb_hcd *hcd, bool hibernated) { struct ohci_hcd *ohci = hcd_to_ohci(hcd); int port; bool need_reinit = false; set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); /* Make sure resume from hibernation re-enumerates everything */ if (hibernated) ohci_usb_reset(ohci); /* See if the controller is already running or has been reset */ ohci->hc_control = ohci_readl(ohci, &ohci->regs->control); if (ohci->hc_control & (OHCI_CTRL_IR | OHCI_SCHED_ENABLES)) { need_reinit = true; } else { switch (ohci->hc_control & OHCI_CTRL_HCFS) { case OHCI_USB_OPER: case OHCI_USB_RESET: need_reinit = true; } } /* If needed, reinitialize and suspend the root hub */ if (need_reinit) { spin_lock_irq(&ohci->lock); ohci_rh_resume(ohci); ohci_rh_suspend(ohci, 0); spin_unlock_irq(&ohci->lock); } /* Normally just turn on port power and enable interrupts */ else { ohci_dbg(ohci, "powerup ports\n"); for (port = 0; port < ohci->num_ports; port++) ohci_writel(ohci, RH_PS_PPS, &ohci->regs->roothub.portstatus[port]); ohci_writel(ohci, OHCI_INTR_MIE, &ohci->regs->intrenable); ohci_readl(ohci, &ohci->regs->intrenable); msleep(20); } usb_hcd_resume_root_hub(hcd); return 0; } EXPORT_SYMBOL_GPL(ohci_resume); #endif /*-------------------------------------------------------------------------*/ /* * Generic structure: This gets copied for platform drivers so that * individual entries can be overridden as needed. */ static const struct hc_driver ohci_hc_driver = { .description = hcd_name, .product_desc = "OHCI Host Controller", .hcd_priv_size = sizeof(struct ohci_hcd), /* * generic hardware linkage */ .irq = ohci_irq, .flags = HCD_MEMORY | HCD_DMA | HCD_USB11, /* * basic lifecycle operations */ .reset = ohci_setup, .start = ohci_start, .stop = ohci_stop, .shutdown = ohci_shutdown, /* * managing i/o requests and associated device resources */ .urb_enqueue = ohci_urb_enqueue, .urb_dequeue = ohci_urb_dequeue, .endpoint_disable = ohci_endpoint_disable, /* * scheduling support */ .get_frame_number = ohci_get_frame, /* * root hub support */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, #endif .start_port_reset = ohci_start_port_reset, }; void ohci_init_driver(struct hc_driver *drv, const struct ohci_driver_overrides *over) { /* Copy the generic table to drv and then apply the overrides */ *drv = ohci_hc_driver; if (over) { drv->product_desc = over->product_desc; drv->hcd_priv_size += over->extra_priv_size; if (over->reset) drv->reset = over->reset; } } EXPORT_SYMBOL_GPL(ohci_init_driver); /*-------------------------------------------------------------------------*/ MODULE_AUTHOR (DRIVER_AUTHOR); MODULE_DESCRIPTION(DRIVER_DESC); MODULE_LICENSE ("GPL"); #if defined(CONFIG_ARCH_SA1100) && defined(CONFIG_SA1111) #include "ohci-sa1111.c" #define SA1111_DRIVER ohci_hcd_sa1111_driver #endif #ifdef CONFIG_USB_OHCI_HCD_PPC_OF #include "ohci-ppc-of.c" #define OF_PLATFORM_DRIVER ohci_hcd_ppc_of_driver #endif #ifdef CONFIG_PPC_PS3 #include "ohci-ps3.c" #define PS3_SYSTEM_BUS_DRIVER ps3_ohci_driver #endif #ifdef CONFIG_MFD_SM501 #include "ohci-sm501.c" #define SM501_OHCI_DRIVER ohci_hcd_sm501_driver #endif #ifdef CONFIG_MFD_TC6393XB #include "ohci-tmio.c" #define TMIO_OHCI_DRIVER ohci_hcd_tmio_driver #endif static int __init ohci_hcd_mod_init(void) { int retval = 0; if (usb_disabled()) return -ENODEV; printk(KERN_INFO "%s: " DRIVER_DESC "\n", hcd_name); pr_debug ("%s: block sizes: ed %zd td %zd\n", hcd_name, sizeof (struct ed), sizeof (struct td)); set_bit(USB_OHCI_LOADED, &usb_hcds_loaded); ohci_debug_root = debugfs_create_dir("ohci", usb_debug_root); #ifdef PS3_SYSTEM_BUS_DRIVER retval = ps3_ohci_driver_register(&PS3_SYSTEM_BUS_DRIVER); if (retval < 0) goto error_ps3; #endif #ifdef OF_PLATFORM_DRIVER retval = platform_driver_register(&OF_PLATFORM_DRIVER); if (retval < 0) goto error_of_platform; #endif #ifdef SA1111_DRIVER retval = sa1111_driver_register(&SA1111_DRIVER); if (retval < 0) goto error_sa1111; #endif #ifdef SM501_OHCI_DRIVER retval = platform_driver_register(&SM501_OHCI_DRIVER); if (retval < 0) goto error_sm501; #endif #ifdef TMIO_OHCI_DRIVER retval = platform_driver_register(&TMIO_OHCI_DRIVER); if (retval < 0) goto error_tmio; #endif return retval; /* Error path */ #ifdef TMIO_OHCI_DRIVER platform_driver_unregister(&TMIO_OHCI_DRIVER); error_tmio: #endif #ifdef SM501_OHCI_DRIVER platform_driver_unregister(&SM501_OHCI_DRIVER); error_sm501: #endif #ifdef SA1111_DRIVER sa1111_driver_unregister(&SA1111_DRIVER); error_sa1111: #endif #ifdef OF_PLATFORM_DRIVER platform_driver_unregister(&OF_PLATFORM_DRIVER); error_of_platform: #endif #ifdef PS3_SYSTEM_BUS_DRIVER ps3_ohci_driver_unregister(&PS3_SYSTEM_BUS_DRIVER); error_ps3: #endif debugfs_remove(ohci_debug_root); ohci_debug_root = NULL; clear_bit(USB_OHCI_LOADED, &usb_hcds_loaded); return retval; } module_init(ohci_hcd_mod_init); static void __exit ohci_hcd_mod_exit(void) { #ifdef TMIO_OHCI_DRIVER platform_driver_unregister(&TMIO_OHCI_DRIVER); #endif #ifdef SM501_OHCI_DRIVER platform_driver_unregister(&SM501_OHCI_DRIVER); #endif #ifdef SA1111_DRIVER sa1111_driver_unregister(&SA1111_DRIVER); #endif #ifdef OF_PLATFORM_DRIVER platform_driver_unregister(&OF_PLATFORM_DRIVER); #endif #ifdef PS3_SYSTEM_BUS_DRIVER ps3_ohci_driver_unregister(&PS3_SYSTEM_BUS_DRIVER); #endif debugfs_remove(ohci_debug_root); clear_bit(USB_OHCI_LOADED, &usb_hcds_loaded); } module_exit(ohci_hcd_mod_exit);