// SPDX-License-Identifier: GPL-2.0+ /* * F81532/F81534 USB to Serial Ports Bridge * * F81532 => 2 Serial Ports * F81534 => 4 Serial Ports * * Copyright (C) 2016 Feature Integration Technology Inc., (Fintek) * Copyright (C) 2016 Tom Tsai (Tom_Tsai@fintek.com.tw) * Copyright (C) 2016 Peter Hong (Peter_Hong@fintek.com.tw) * * The F81532/F81534 had 1 control endpoint for setting, 1 endpoint bulk-out * for all serial port TX and 1 endpoint bulk-in for all serial port read in * (Read Data/MSR/LSR). * * Write URB is fixed with 512bytes, per serial port used 128Bytes. * It can be described by f81534_prepare_write_buffer() * * Read URB is 512Bytes max, per serial port used 128Bytes. * It can be described by f81534_process_read_urb() and maybe received with * 128x1,2,3,4 bytes. * */ #include #include #include #include #include #include #include #include /* Serial Port register Address */ #define F81534_UART_BASE_ADDRESS 0x1200 #define F81534_UART_OFFSET 0x10 #define F81534_DIVISOR_LSB_REG (0x00 + F81534_UART_BASE_ADDRESS) #define F81534_DIVISOR_MSB_REG (0x01 + F81534_UART_BASE_ADDRESS) #define F81534_INTERRUPT_ENABLE_REG (0x01 + F81534_UART_BASE_ADDRESS) #define F81534_FIFO_CONTROL_REG (0x02 + F81534_UART_BASE_ADDRESS) #define F81534_LINE_CONTROL_REG (0x03 + F81534_UART_BASE_ADDRESS) #define F81534_MODEM_CONTROL_REG (0x04 + F81534_UART_BASE_ADDRESS) #define F81534_LINE_STATUS_REG (0x05 + F81534_UART_BASE_ADDRESS) #define F81534_MODEM_STATUS_REG (0x06 + F81534_UART_BASE_ADDRESS) #define F81534_CLOCK_REG (0x08 + F81534_UART_BASE_ADDRESS) #define F81534_CONFIG1_REG (0x09 + F81534_UART_BASE_ADDRESS) #define F81534_DEF_CONF_ADDRESS_START 0x3000 #define F81534_DEF_CONF_SIZE 12 #define F81534_CUSTOM_ADDRESS_START 0x2f00 #define F81534_CUSTOM_DATA_SIZE 0x10 #define F81534_CUSTOM_NO_CUSTOM_DATA 0xff #define F81534_CUSTOM_VALID_TOKEN 0xf0 #define F81534_CONF_OFFSET 1 #define F81534_CONF_INIT_GPIO_OFFSET 4 #define F81534_CONF_WORK_GPIO_OFFSET 8 #define F81534_CONF_GPIO_SHUTDOWN 7 #define F81534_CONF_GPIO_RS232 1 #define F81534_MAX_DATA_BLOCK 64 #define F81534_MAX_BUS_RETRY 20 /* Default URB timeout for USB operations */ #define F81534_USB_MAX_RETRY 10 #define F81534_USB_TIMEOUT 2000 #define F81534_SET_GET_REGISTER 0xA0 #define F81534_NUM_PORT 4 #define F81534_UNUSED_PORT 0xff #define F81534_WRITE_BUFFER_SIZE 512 #define DRIVER_DESC "Fintek F81532/F81534" #define FINTEK_VENDOR_ID_1 0x1934 #define FINTEK_VENDOR_ID_2 0x2C42 #define FINTEK_DEVICE_ID 0x1202 #define F81534_MAX_TX_SIZE 124 #define F81534_MAX_RX_SIZE 124 #define F81534_RECEIVE_BLOCK_SIZE 128 #define F81534_MAX_RECEIVE_BLOCK_SIZE 512 #define F81534_TOKEN_RECEIVE 0x01 #define F81534_TOKEN_WRITE 0x02 #define F81534_TOKEN_TX_EMPTY 0x03 #define F81534_TOKEN_MSR_CHANGE 0x04 /* * We used interal SPI bus to access FLASH section. We must wait the SPI bus to * idle if we performed any command. * * SPI Bus status register: F81534_BUS_REG_STATUS * Bit 0/1 : BUSY * Bit 2 : IDLE */ #define F81534_BUS_BUSY (BIT(0) | BIT(1)) #define F81534_BUS_IDLE BIT(2) #define F81534_BUS_READ_DATA 0x1004 #define F81534_BUS_REG_STATUS 0x1003 #define F81534_BUS_REG_START 0x1002 #define F81534_BUS_REG_END 0x1001 #define F81534_CMD_READ 0x03 #define F81534_DEFAULT_BAUD_RATE 9600 #define F81534_PORT_CONF_RS232 0 #define F81534_PORT_CONF_RS485 BIT(0) #define F81534_PORT_CONF_RS485_INVERT (BIT(0) | BIT(1)) #define F81534_PORT_CONF_MODE_MASK GENMASK(1, 0) #define F81534_PORT_CONF_DISABLE_PORT BIT(3) #define F81534_PORT_CONF_NOT_EXIST_PORT BIT(7) #define F81534_PORT_UNAVAILABLE \ (F81534_PORT_CONF_DISABLE_PORT | F81534_PORT_CONF_NOT_EXIST_PORT) #define F81534_1X_RXTRIGGER 0xc3 #define F81534_8X_RXTRIGGER 0xcf /* * F81532/534 Clock registers (offset +08h) * * Bit0: UART Enable (always on) * Bit2-1: Clock source selector * 00: 1.846MHz. * 01: 18.46MHz. * 10: 24MHz. * 11: 14.77MHz. * Bit4: Auto direction(RTS) control (RTS pin Low when TX) * Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX) */ #define F81534_UART_EN BIT(0) #define F81534_CLK_1_846_MHZ 0 #define F81534_CLK_18_46_MHZ BIT(1) #define F81534_CLK_24_MHZ BIT(2) #define F81534_CLK_14_77_MHZ (BIT(1) | BIT(2)) #define F81534_CLK_MASK GENMASK(2, 1) #define F81534_CLK_TX_DELAY_1BIT BIT(3) #define F81534_CLK_RS485_MODE BIT(4) #define F81534_CLK_RS485_INVERT BIT(5) static const struct usb_device_id f81534_id_table[] = { { USB_DEVICE(FINTEK_VENDOR_ID_1, FINTEK_DEVICE_ID) }, { USB_DEVICE(FINTEK_VENDOR_ID_2, FINTEK_DEVICE_ID) }, {} /* Terminating entry */ }; #define F81534_TX_EMPTY_BIT 0 struct f81534_serial_private { u8 conf_data[F81534_DEF_CONF_SIZE]; int tty_idx[F81534_NUM_PORT]; u8 setting_idx; int opened_port; struct mutex urb_mutex; }; struct f81534_port_private { struct mutex mcr_mutex; struct mutex lcr_mutex; struct work_struct lsr_work; struct usb_serial_port *port; unsigned long tx_empty; spinlock_t msr_lock; u32 baud_base; u8 shadow_mcr; u8 shadow_lcr; u8 shadow_msr; u8 shadow_clk; u8 phy_num; }; struct f81534_pin_data { const u16 reg_addr; const u8 reg_mask; }; struct f81534_port_out_pin { struct f81534_pin_data pin[3]; }; /* Pin output value for M2/M1/M0(SD) */ static const struct f81534_port_out_pin f81534_port_out_pins[] = { { { { 0x2ae8, BIT(7) }, { 0x2a90, BIT(5) }, { 0x2a90, BIT(4) } } }, { { { 0x2ae8, BIT(6) }, { 0x2ae8, BIT(0) }, { 0x2ae8, BIT(3) } } }, { { { 0x2a90, BIT(0) }, { 0x2ae8, BIT(2) }, { 0x2a80, BIT(6) } } }, { { { 0x2a90, BIT(3) }, { 0x2a90, BIT(2) }, { 0x2a90, BIT(1) } } }, }; static u32 const baudrate_table[] = { 115200, 921600, 1152000, 1500000 }; static u8 const clock_table[] = { F81534_CLK_1_846_MHZ, F81534_CLK_14_77_MHZ, F81534_CLK_18_46_MHZ, F81534_CLK_24_MHZ }; static int f81534_logic_to_phy_port(struct usb_serial *serial, struct usb_serial_port *port) { struct f81534_serial_private *serial_priv = usb_get_serial_data(port->serial); int count = 0; int i; for (i = 0; i < F81534_NUM_PORT; ++i) { if (serial_priv->conf_data[i] & F81534_PORT_UNAVAILABLE) continue; if (port->port_number == count) return i; ++count; } return -ENODEV; } static int f81534_set_register(struct usb_serial *serial, u16 reg, u8 data) { struct usb_interface *interface = serial->interface; struct usb_device *dev = serial->dev; size_t count = F81534_USB_MAX_RETRY; int status; u8 *tmp; tmp = kmalloc(sizeof(u8), GFP_KERNEL); if (!tmp) return -ENOMEM; *tmp = data; /* * Our device maybe not reply when heavily loading, We'll retry for * F81534_USB_MAX_RETRY times. */ while (count--) { status = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), F81534_SET_GET_REGISTER, USB_TYPE_VENDOR | USB_DIR_OUT, reg, 0, tmp, sizeof(u8), F81534_USB_TIMEOUT); if (status > 0) { status = 0; break; } else if (status == 0) { status = -EIO; } } if (status < 0) { dev_err(&interface->dev, "%s: reg: %x data: %x failed: %d\n", __func__, reg, data, status); } kfree(tmp); return status; } static int f81534_get_register(struct usb_serial *serial, u16 reg, u8 *data) { struct usb_interface *interface = serial->interface; struct usb_device *dev = serial->dev; size_t count = F81534_USB_MAX_RETRY; int status; u8 *tmp; tmp = kmalloc(sizeof(u8), GFP_KERNEL); if (!tmp) return -ENOMEM; /* * Our device maybe not reply when heavily loading, We'll retry for * F81534_USB_MAX_RETRY times. */ while (count--) { status = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), F81534_SET_GET_REGISTER, USB_TYPE_VENDOR | USB_DIR_IN, reg, 0, tmp, sizeof(u8), F81534_USB_TIMEOUT); if (status > 0) { status = 0; break; } else if (status == 0) { status = -EIO; } } if (status < 0) { dev_err(&interface->dev, "%s: reg: %x failed: %d\n", __func__, reg, status); goto end; } *data = *tmp; end: kfree(tmp); return status; } static int f81534_set_mask_register(struct usb_serial *serial, u16 reg, u8 mask, u8 data) { int status; u8 tmp; status = f81534_get_register(serial, reg, &tmp); if (status) return status; tmp &= ~mask; tmp |= (mask & data); return f81534_set_register(serial, reg, tmp); } static int f81534_set_phy_port_register(struct usb_serial *serial, int phy, u16 reg, u8 data) { return f81534_set_register(serial, reg + F81534_UART_OFFSET * phy, data); } static int f81534_get_phy_port_register(struct usb_serial *serial, int phy, u16 reg, u8 *data) { return f81534_get_register(serial, reg + F81534_UART_OFFSET * phy, data); } static int f81534_set_port_register(struct usb_serial_port *port, u16 reg, u8 data) { struct f81534_port_private *port_priv = usb_get_serial_port_data(port); return f81534_set_register(port->serial, reg + port_priv->phy_num * F81534_UART_OFFSET, data); } static int f81534_get_port_register(struct usb_serial_port *port, u16 reg, u8 *data) { struct f81534_port_private *port_priv = usb_get_serial_port_data(port); return f81534_get_register(port->serial, reg + port_priv->phy_num * F81534_UART_OFFSET, data); } /* * If we try to access the internal flash via SPI bus, we should check the bus * status for every command. e.g., F81534_BUS_REG_START/F81534_BUS_REG_END */ static int f81534_wait_for_spi_idle(struct usb_serial *serial) { size_t count = F81534_MAX_BUS_RETRY; u8 tmp; int status; do { status = f81534_get_register(serial, F81534_BUS_REG_STATUS, &tmp); if (status) return status; if (tmp & F81534_BUS_BUSY) continue; if (tmp & F81534_BUS_IDLE) break; } while (--count); if (!count) { dev_err(&serial->interface->dev, "%s: timed out waiting for idle SPI bus\n", __func__); return -EIO; } return f81534_set_register(serial, F81534_BUS_REG_STATUS, tmp & ~F81534_BUS_IDLE); } static int f81534_get_spi_register(struct usb_serial *serial, u16 reg, u8 *data) { int status; status = f81534_get_register(serial, reg, data); if (status) return status; return f81534_wait_for_spi_idle(serial); } static int f81534_set_spi_register(struct usb_serial *serial, u16 reg, u8 data) { int status; status = f81534_set_register(serial, reg, data); if (status) return status; return f81534_wait_for_spi_idle(serial); } static int f81534_read_flash(struct usb_serial *serial, u32 address, size_t size, u8 *buf) { u8 tmp_buf[F81534_MAX_DATA_BLOCK]; size_t block = 0; size_t read_size; size_t count; int status; int offset; u16 reg_tmp; status = f81534_set_spi_register(serial, F81534_BUS_REG_START, F81534_CMD_READ); if (status) return status; status = f81534_set_spi_register(serial, F81534_BUS_REG_START, (address >> 16) & 0xff); if (status) return status; status = f81534_set_spi_register(serial, F81534_BUS_REG_START, (address >> 8) & 0xff); if (status) return status; status = f81534_set_spi_register(serial, F81534_BUS_REG_START, (address >> 0) & 0xff); if (status) return status; /* Continuous read mode */ do { read_size = min_t(size_t, F81534_MAX_DATA_BLOCK, size); for (count = 0; count < read_size; ++count) { /* To write F81534_BUS_REG_END when final byte */ if (size <= F81534_MAX_DATA_BLOCK && read_size == count + 1) reg_tmp = F81534_BUS_REG_END; else reg_tmp = F81534_BUS_REG_START; /* * Dummy code, force IC to generate a read pulse, the * set of value 0xf1 is dont care (any value is ok) */ status = f81534_set_spi_register(serial, reg_tmp, 0xf1); if (status) return status; status = f81534_get_spi_register(serial, F81534_BUS_READ_DATA, &tmp_buf[count]); if (status) return status; offset = count + block * F81534_MAX_DATA_BLOCK; buf[offset] = tmp_buf[count]; } size -= read_size; ++block; } while (size); return 0; } static void f81534_prepare_write_buffer(struct usb_serial_port *port, u8 *buf) { struct f81534_port_private *port_priv = usb_get_serial_port_data(port); int phy_num = port_priv->phy_num; u8 tx_len; int i; /* * The block layout is fixed with 4x128 Bytes, per 128 Bytes a port. * index 0: port phy idx (e.g., 0,1,2,3) * index 1: only F81534_TOKEN_WRITE * index 2: serial TX out length * index 3: fix to 0 * index 4~127: serial out data block */ for (i = 0; i < F81534_NUM_PORT; ++i) { buf[i * F81534_RECEIVE_BLOCK_SIZE] = i; buf[i * F81534_RECEIVE_BLOCK_SIZE + 1] = F81534_TOKEN_WRITE; buf[i * F81534_RECEIVE_BLOCK_SIZE + 2] = 0; buf[i * F81534_RECEIVE_BLOCK_SIZE + 3] = 0; } tx_len = kfifo_out_locked(&port->write_fifo, &buf[phy_num * F81534_RECEIVE_BLOCK_SIZE + 4], F81534_MAX_TX_SIZE, &port->lock); buf[phy_num * F81534_RECEIVE_BLOCK_SIZE + 2] = tx_len; } static int f81534_submit_writer(struct usb_serial_port *port, gfp_t mem_flags) { struct f81534_port_private *port_priv = usb_get_serial_port_data(port); struct urb *urb; unsigned long flags; int result; /* Check is any data in write_fifo */ spin_lock_irqsave(&port->lock, flags); if (kfifo_is_empty(&port->write_fifo)) { spin_unlock_irqrestore(&port->lock, flags); return 0; } spin_unlock_irqrestore(&port->lock, flags); /* Check H/W is TXEMPTY */ if (!test_and_clear_bit(F81534_TX_EMPTY_BIT, &port_priv->tx_empty)) return 0; urb = port->write_urbs[0]; f81534_prepare_write_buffer(port, port->bulk_out_buffers[0]); urb->transfer_buffer_length = F81534_WRITE_BUFFER_SIZE; result = usb_submit_urb(urb, mem_flags); if (result) { set_bit(F81534_TX_EMPTY_BIT, &port_priv->tx_empty); dev_err(&port->dev, "%s: submit failed: %d\n", __func__, result); return result; } usb_serial_port_softint(port); return 0; } static u32 f81534_calc_baud_divisor(u32 baudrate, u32 clockrate) { /* Round to nearest divisor */ return DIV_ROUND_CLOSEST(clockrate, baudrate); } static int f81534_find_clk(u32 baudrate) { int idx; for (idx = 0; idx < ARRAY_SIZE(baudrate_table); ++idx) { if (baudrate <= baudrate_table[idx] && baudrate_table[idx] % baudrate == 0) return idx; } return -EINVAL; } static int f81534_set_port_config(struct usb_serial_port *port, struct tty_struct *tty, u32 baudrate, u32 old_baudrate, u8 lcr) { struct f81534_port_private *port_priv = usb_get_serial_port_data(port); u32 divisor; int status; int i; int idx; u8 value; u32 baud_list[] = {baudrate, old_baudrate, F81534_DEFAULT_BAUD_RATE}; for (i = 0; i < ARRAY_SIZE(baud_list); ++i) { baudrate = baud_list[i]; if (baudrate == 0) { tty_encode_baud_rate(tty, 0, 0); return 0; } idx = f81534_find_clk(baudrate); if (idx >= 0) { tty_encode_baud_rate(tty, baudrate, baudrate); break; } } if (idx < 0) return -EINVAL; port_priv->baud_base = baudrate_table[idx]; port_priv->shadow_clk &= ~F81534_CLK_MASK; port_priv->shadow_clk |= clock_table[idx]; status = f81534_set_port_register(port, F81534_CLOCK_REG, port_priv->shadow_clk); if (status) { dev_err(&port->dev, "CLOCK_REG setting failed\n"); return status; } if (baudrate <= 1200) value = F81534_1X_RXTRIGGER; /* 128 FIFO & TL: 1x */ else value = F81534_8X_RXTRIGGER; /* 128 FIFO & TL: 8x */ status = f81534_set_port_register(port, F81534_CONFIG1_REG, value); if (status) { dev_err(&port->dev, "%s: CONFIG1 setting failed\n", __func__); return status; } if (baudrate <= 1200) value = UART_FCR_TRIGGER_1 | UART_FCR_ENABLE_FIFO; /* TL: 1 */ else value = UART_FCR_TRIGGER_8 | UART_FCR_ENABLE_FIFO; /* TL: 8 */ status = f81534_set_port_register(port, F81534_FIFO_CONTROL_REG, value); if (status) { dev_err(&port->dev, "%s: FCR setting failed\n", __func__); return status; } divisor = f81534_calc_baud_divisor(baudrate, port_priv->baud_base); mutex_lock(&port_priv->lcr_mutex); value = UART_LCR_DLAB; status = f81534_set_port_register(port, F81534_LINE_CONTROL_REG, value); if (status) { dev_err(&port->dev, "%s: set LCR failed\n", __func__); goto out_unlock; } value = divisor & 0xff; status = f81534_set_port_register(port, F81534_DIVISOR_LSB_REG, value); if (status) { dev_err(&port->dev, "%s: set DLAB LSB failed\n", __func__); goto out_unlock; } value = (divisor >> 8) & 0xff; status = f81534_set_port_register(port, F81534_DIVISOR_MSB_REG, value); if (status) { dev_err(&port->dev, "%s: set DLAB MSB failed\n", __func__); goto out_unlock; } value = lcr | (port_priv->shadow_lcr & UART_LCR_SBC); status = f81534_set_port_register(port, F81534_LINE_CONTROL_REG, value); if (status) { dev_err(&port->dev, "%s: set LCR failed\n", __func__); goto out_unlock; } port_priv->shadow_lcr = value; out_unlock: mutex_unlock(&port_priv->lcr_mutex); return status; } static void f81534_break_ctl(struct tty_struct *tty, int break_state) { struct usb_serial_port *port = tty->driver_data; struct f81534_port_private *port_priv = usb_get_serial_port_data(port); int status; mutex_lock(&port_priv->lcr_mutex); if (break_state) port_priv->shadow_lcr |= UART_LCR_SBC; else port_priv->shadow_lcr &= ~UART_LCR_SBC; status = f81534_set_port_register(port, F81534_LINE_CONTROL_REG, port_priv->shadow_lcr); if (status) dev_err(&port->dev, "set break failed: %d\n", status); mutex_unlock(&port_priv->lcr_mutex); } static int f81534_update_mctrl(struct usb_serial_port *port, unsigned int set, unsigned int clear) { struct f81534_port_private *port_priv = usb_get_serial_port_data(port); int status; u8 tmp; if (((set | clear) & (TIOCM_DTR | TIOCM_RTS)) == 0) return 0; /* no change */ mutex_lock(&port_priv->mcr_mutex); /* 'Set' takes precedence over 'Clear' */ clear &= ~set; /* Always enable UART_MCR_OUT2 */ tmp = UART_MCR_OUT2 | port_priv->shadow_mcr; if (clear & TIOCM_DTR) tmp &= ~UART_MCR_DTR; if (clear & TIOCM_RTS) tmp &= ~UART_MCR_RTS; if (set & TIOCM_DTR) tmp |= UART_MCR_DTR; if (set & TIOCM_RTS) tmp |= UART_MCR_RTS; status = f81534_set_port_register(port, F81534_MODEM_CONTROL_REG, tmp); if (status < 0) { dev_err(&port->dev, "%s: MCR write failed\n", __func__); mutex_unlock(&port_priv->mcr_mutex); return status; } port_priv->shadow_mcr = tmp; mutex_unlock(&port_priv->mcr_mutex); return 0; } /* * This function will search the data area with token F81534_CUSTOM_VALID_TOKEN * for latest configuration index. If nothing found * (*index = F81534_CUSTOM_NO_CUSTOM_DATA), We'll load default configure in * F81534_DEF_CONF_ADDRESS_START section. * * Due to we only use block0 to save data, so *index should be 0 or * F81534_CUSTOM_NO_CUSTOM_DATA. */ static int f81534_find_config_idx(struct usb_serial *serial, u8 *index) { u8 tmp; int status; status = f81534_read_flash(serial, F81534_CUSTOM_ADDRESS_START, 1, &tmp); if (status) { dev_err(&serial->interface->dev, "%s: read failed: %d\n", __func__, status); return status; } /* We'll use the custom data when the data is valid. */ if (tmp == F81534_CUSTOM_VALID_TOKEN) *index = 0; else *index = F81534_CUSTOM_NO_CUSTOM_DATA; return 0; } /* * The F81532/534 will not report serial port to USB serial subsystem when * H/W DCD/DSR/CTS/RI/RX pin connected to ground. * * To detect RX pin status, we'll enable MCR interal loopback, disable it and * delayed for 60ms. It connected to ground If LSR register report UART_LSR_BI. */ static bool f81534_check_port_hw_disabled(struct usb_serial *serial, int phy) { int status; u8 old_mcr; u8 msr; u8 lsr; u8 msr_mask; msr_mask = UART_MSR_DCD | UART_MSR_RI | UART_MSR_DSR | UART_MSR_CTS; status = f81534_get_phy_port_register(serial, phy, F81534_MODEM_STATUS_REG, &msr); if (status) return false; if ((msr & msr_mask) != msr_mask) return false; status = f81534_set_phy_port_register(serial, phy, F81534_FIFO_CONTROL_REG, UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); if (status) return false; status = f81534_get_phy_port_register(serial, phy, F81534_MODEM_CONTROL_REG, &old_mcr); if (status) return false; status = f81534_set_phy_port_register(serial, phy, F81534_MODEM_CONTROL_REG, UART_MCR_LOOP); if (status) return false; status = f81534_set_phy_port_register(serial, phy, F81534_MODEM_CONTROL_REG, 0x0); if (status) return false; msleep(60); status = f81534_get_phy_port_register(serial, phy, F81534_LINE_STATUS_REG, &lsr); if (status) return false; status = f81534_set_phy_port_register(serial, phy, F81534_MODEM_CONTROL_REG, old_mcr); if (status) return false; if ((lsr & UART_LSR_BI) == UART_LSR_BI) return true; return false; } /* * We had 2 generation of F81532/534 IC. All has an internal storage. * * 1st is pure USB-to-TTL RS232 IC and designed for 4 ports only, no any * internal data will used. All mode and gpio control should manually set * by AP or Driver and all storage space value are 0xff. The * f81534_calc_num_ports() will run to final we marked as "oldest version" * for this IC. * * 2rd is designed to more generic to use any transceiver and this is our * mass production type. We'll save data in F81534_CUSTOM_ADDRESS_START * (0x2f00) with 9bytes. The 1st byte is a indicater. If the token is * F81534_CUSTOM_VALID_TOKEN(0xf0), the IC is 2nd gen type, the following * 4bytes save port mode (0:RS232/1:RS485 Invert/2:RS485), and the last * 4bytes save GPIO state(value from 0~7 to represent 3 GPIO output pin). * The f81534_calc_num_ports() will run to "new style" with checking * F81534_PORT_UNAVAILABLE section. */ static int f81534_calc_num_ports(struct usb_serial *serial, struct usb_serial_endpoints *epds) { struct f81534_serial_private *serial_priv; struct device *dev = &serial->interface->dev; int size_bulk_in = usb_endpoint_maxp(epds->bulk_in[0]); int size_bulk_out = usb_endpoint_maxp(epds->bulk_out[0]); u8 num_port = 0; int index = 0; int status; int i; if (size_bulk_out != F81534_WRITE_BUFFER_SIZE || size_bulk_in != F81534_MAX_RECEIVE_BLOCK_SIZE) { dev_err(dev, "unsupported endpoint max packet size\n"); return -ENODEV; } serial_priv = devm_kzalloc(&serial->interface->dev, sizeof(*serial_priv), GFP_KERNEL); if (!serial_priv) return -ENOMEM; usb_set_serial_data(serial, serial_priv); mutex_init(&serial_priv->urb_mutex); /* Check had custom setting */ status = f81534_find_config_idx(serial, &serial_priv->setting_idx); if (status) { dev_err(&serial->interface->dev, "%s: find idx failed: %d\n", __func__, status); return status; } /* * We'll read custom data only when data available, otherwise we'll * read default value instead. */ if (serial_priv->setting_idx != F81534_CUSTOM_NO_CUSTOM_DATA) { status = f81534_read_flash(serial, F81534_CUSTOM_ADDRESS_START + F81534_CONF_OFFSET, sizeof(serial_priv->conf_data), serial_priv->conf_data); if (status) { dev_err(&serial->interface->dev, "%s: get custom data failed: %d\n", __func__, status); return status; } dev_dbg(&serial->interface->dev, "%s: read config from block: %d\n", __func__, serial_priv->setting_idx); } else { /* Read default board setting */ status = f81534_read_flash(serial, F81534_DEF_CONF_ADDRESS_START, sizeof(serial_priv->conf_data), serial_priv->conf_data); if (status) { dev_err(&serial->interface->dev, "%s: read failed: %d\n", __func__, status); return status; } dev_dbg(&serial->interface->dev, "%s: read default config\n", __func__); } /* New style, find all possible ports */ for (i = 0; i < F81534_NUM_PORT; ++i) { if (f81534_check_port_hw_disabled(serial, i)) serial_priv->conf_data[i] |= F81534_PORT_UNAVAILABLE; if (serial_priv->conf_data[i] & F81534_PORT_UNAVAILABLE) continue; ++num_port; } if (!num_port) { dev_warn(&serial->interface->dev, "no config found, assuming 4 ports\n"); num_port = 4; /* Nothing found, oldest version IC */ } /* Assign phy-to-logic mapping */ for (i = 0; i < F81534_NUM_PORT; ++i) { if (serial_priv->conf_data[i] & F81534_PORT_UNAVAILABLE) continue; serial_priv->tty_idx[i] = index++; dev_dbg(&serial->interface->dev, "%s: phy_num: %d, tty_idx: %d\n", __func__, i, serial_priv->tty_idx[i]); } /* * Setup bulk-out endpoint multiplexing. All ports share the same * bulk-out endpoint. */ BUILD_BUG_ON(ARRAY_SIZE(epds->bulk_out) < F81534_NUM_PORT); for (i = 1; i < num_port; ++i) epds->bulk_out[i] = epds->bulk_out[0]; epds->num_bulk_out = num_port; return num_port; } static void f81534_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old_termios) { u8 new_lcr = 0; int status; u32 baud; u32 old_baud; if (C_BAUD(tty) == B0) f81534_update_mctrl(port, 0, TIOCM_DTR | TIOCM_RTS); else if (old_termios && (old_termios->c_cflag & CBAUD) == B0) f81534_update_mctrl(port, TIOCM_DTR | TIOCM_RTS, 0); if (C_PARENB(tty)) { new_lcr |= UART_LCR_PARITY; if (!C_PARODD(tty)) new_lcr |= UART_LCR_EPAR; if (C_CMSPAR(tty)) new_lcr |= UART_LCR_SPAR; } if (C_CSTOPB(tty)) new_lcr |= UART_LCR_STOP; switch (C_CSIZE(tty)) { case CS5: new_lcr |= UART_LCR_WLEN5; break; case CS6: new_lcr |= UART_LCR_WLEN6; break; case CS7: new_lcr |= UART_LCR_WLEN7; break; default: case CS8: new_lcr |= UART_LCR_WLEN8; break; } baud = tty_get_baud_rate(tty); if (!baud) return; if (old_termios) old_baud = tty_termios_baud_rate(old_termios); else old_baud = F81534_DEFAULT_BAUD_RATE; dev_dbg(&port->dev, "%s: baud: %d\n", __func__, baud); status = f81534_set_port_config(port, tty, baud, old_baud, new_lcr); if (status < 0) { dev_err(&port->dev, "%s: set port config failed: %d\n", __func__, status); } } static int f81534_submit_read_urb(struct usb_serial *serial, gfp_t flags) { return usb_serial_generic_submit_read_urbs(serial->port[0], flags); } static void f81534_msr_changed(struct usb_serial_port *port, u8 msr) { struct f81534_port_private *port_priv = usb_get_serial_port_data(port); struct tty_struct *tty; unsigned long flags; u8 old_msr; if (!(msr & UART_MSR_ANY_DELTA)) return; spin_lock_irqsave(&port_priv->msr_lock, flags); old_msr = port_priv->shadow_msr; port_priv->shadow_msr = msr; spin_unlock_irqrestore(&port_priv->msr_lock, flags); dev_dbg(&port->dev, "%s: MSR from %02x to %02x\n", __func__, old_msr, msr); /* Update input line counters */ if (msr & UART_MSR_DCTS) port->icount.cts++; if (msr & UART_MSR_DDSR) port->icount.dsr++; if (msr & UART_MSR_DDCD) port->icount.dcd++; if (msr & UART_MSR_TERI) port->icount.rng++; wake_up_interruptible(&port->port.delta_msr_wait); if (!(msr & UART_MSR_DDCD)) return; dev_dbg(&port->dev, "%s: DCD Changed: phy_num: %d from %x to %x\n", __func__, port_priv->phy_num, old_msr, msr); tty = tty_port_tty_get(&port->port); if (!tty) return; usb_serial_handle_dcd_change(port, tty, msr & UART_MSR_DCD); tty_kref_put(tty); } static int f81534_read_msr(struct usb_serial_port *port) { struct f81534_port_private *port_priv = usb_get_serial_port_data(port); unsigned long flags; int status; u8 msr; /* Get MSR initial value */ status = f81534_get_port_register(port, F81534_MODEM_STATUS_REG, &msr); if (status) return status; /* Force update current state */ spin_lock_irqsave(&port_priv->msr_lock, flags); port_priv->shadow_msr = msr; spin_unlock_irqrestore(&port_priv->msr_lock, flags); return 0; } static int f81534_open(struct tty_struct *tty, struct usb_serial_port *port) { struct f81534_serial_private *serial_priv = usb_get_serial_data(port->serial); struct f81534_port_private *port_priv = usb_get_serial_port_data(port); int status; status = f81534_set_port_register(port, F81534_FIFO_CONTROL_REG, UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); if (status) { dev_err(&port->dev, "%s: Clear FIFO failed: %d\n", __func__, status); return status; } if (tty) f81534_set_termios(tty, port, NULL); status = f81534_read_msr(port); if (status) return status; mutex_lock(&serial_priv->urb_mutex); /* Submit Read URBs for first port opened */ if (!serial_priv->opened_port) { status = f81534_submit_read_urb(port->serial, GFP_KERNEL); if (status) goto exit; } serial_priv->opened_port++; exit: mutex_unlock(&serial_priv->urb_mutex); set_bit(F81534_TX_EMPTY_BIT, &port_priv->tx_empty); return status; } static void f81534_close(struct usb_serial_port *port) { struct f81534_serial_private *serial_priv = usb_get_serial_data(port->serial); struct usb_serial_port *port0 = port->serial->port[0]; unsigned long flags; size_t i; usb_kill_urb(port->write_urbs[0]); spin_lock_irqsave(&port->lock, flags); kfifo_reset_out(&port->write_fifo); spin_unlock_irqrestore(&port->lock, flags); /* Kill Read URBs when final port closed */ mutex_lock(&serial_priv->urb_mutex); serial_priv->opened_port--; if (!serial_priv->opened_port) { for (i = 0; i < ARRAY_SIZE(port0->read_urbs); ++i) usb_kill_urb(port0->read_urbs[i]); } mutex_unlock(&serial_priv->urb_mutex); } static int f81534_get_serial_info(struct tty_struct *tty, struct serial_struct *ss) { struct usb_serial_port *port = tty->driver_data; struct f81534_port_private *port_priv; port_priv = usb_get_serial_port_data(port); ss->type = PORT_16550A; ss->port = port->port_number; ss->line = port->minor; ss->baud_base = port_priv->baud_base; return 0; } static void f81534_process_per_serial_block(struct usb_serial_port *port, u8 *data) { struct f81534_port_private *port_priv = usb_get_serial_port_data(port); int phy_num = data[0]; size_t read_size = 0; size_t i; char tty_flag; int status; u8 lsr; /* * The block layout is 128 Bytes * index 0: port phy idx (e.g., 0,1,2,3), * index 1: It's could be * F81534_TOKEN_RECEIVE * F81534_TOKEN_TX_EMPTY * F81534_TOKEN_MSR_CHANGE * index 2: serial in size (data+lsr, must be even) * meaningful for F81534_TOKEN_RECEIVE only * index 3: current MSR with this device * index 4~127: serial in data block (data+lsr, must be even) */ switch (data[1]) { case F81534_TOKEN_TX_EMPTY: set_bit(F81534_TX_EMPTY_BIT, &port_priv->tx_empty); /* Try to submit writer */ status = f81534_submit_writer(port, GFP_ATOMIC); if (status) dev_err(&port->dev, "%s: submit failed\n", __func__); return; case F81534_TOKEN_MSR_CHANGE: f81534_msr_changed(port, data[3]); return; case F81534_TOKEN_RECEIVE: read_size = data[2]; if (read_size > F81534_MAX_RX_SIZE) { dev_err(&port->dev, "%s: phy: %d read_size: %zu larger than: %d\n", __func__, phy_num, read_size, F81534_MAX_RX_SIZE); return; } break; default: dev_warn(&port->dev, "%s: unknown token: %02x\n", __func__, data[1]); return; } for (i = 4; i < 4 + read_size; i += 2) { tty_flag = TTY_NORMAL; lsr = data[i + 1]; if (lsr & UART_LSR_BRK_ERROR_BITS) { if (lsr & UART_LSR_BI) { tty_flag = TTY_BREAK; port->icount.brk++; usb_serial_handle_break(port); } else if (lsr & UART_LSR_PE) { tty_flag = TTY_PARITY; port->icount.parity++; } else if (lsr & UART_LSR_FE) { tty_flag = TTY_FRAME; port->icount.frame++; } if (lsr & UART_LSR_OE) { port->icount.overrun++; tty_insert_flip_char(&port->port, 0, TTY_OVERRUN); } schedule_work(&port_priv->lsr_work); } if (port->sysrq) { if (usb_serial_handle_sysrq_char(port, data[i])) continue; } tty_insert_flip_char(&port->port, data[i], tty_flag); } tty_flip_buffer_push(&port->port); } static void f81534_process_read_urb(struct urb *urb) { struct f81534_serial_private *serial_priv; struct usb_serial_port *port; struct usb_serial *serial; u8 *buf; int phy_port_num; int tty_port_num; size_t i; if (!urb->actual_length || urb->actual_length % F81534_RECEIVE_BLOCK_SIZE) { return; } port = urb->context; serial = port->serial; buf = urb->transfer_buffer; serial_priv = usb_get_serial_data(serial); for (i = 0; i < urb->actual_length; i += F81534_RECEIVE_BLOCK_SIZE) { phy_port_num = buf[i]; if (phy_port_num >= F81534_NUM_PORT) { dev_err(&port->dev, "%s: phy_port_num: %d larger than: %d\n", __func__, phy_port_num, F81534_NUM_PORT); continue; } tty_port_num = serial_priv->tty_idx[phy_port_num]; port = serial->port[tty_port_num]; if (tty_port_initialized(&port->port)) f81534_process_per_serial_block(port, &buf[i]); } } static void f81534_write_usb_callback(struct urb *urb) { struct usb_serial_port *port = urb->context; switch (urb->status) { case 0: break; case -ENOENT: case -ECONNRESET: case -ESHUTDOWN: dev_dbg(&port->dev, "%s - urb stopped: %d\n", __func__, urb->status); return; case -EPIPE: dev_err(&port->dev, "%s - urb stopped: %d\n", __func__, urb->status); return; default: dev_dbg(&port->dev, "%s - nonzero urb status: %d\n", __func__, urb->status); break; } } static void f81534_lsr_worker(struct work_struct *work) { struct f81534_port_private *port_priv; struct usb_serial_port *port; int status; u8 tmp; port_priv = container_of(work, struct f81534_port_private, lsr_work); port = port_priv->port; status = f81534_get_port_register(port, F81534_LINE_STATUS_REG, &tmp); if (status) dev_warn(&port->dev, "read LSR failed: %d\n", status); } static int f81534_set_port_output_pin(struct usb_serial_port *port) { struct f81534_serial_private *serial_priv; struct f81534_port_private *port_priv; struct usb_serial *serial; const struct f81534_port_out_pin *pins; int status; int i; u8 value; u8 idx; serial = port->serial; serial_priv = usb_get_serial_data(serial); port_priv = usb_get_serial_port_data(port); idx = F81534_CONF_INIT_GPIO_OFFSET + port_priv->phy_num; value = serial_priv->conf_data[idx]; if (value >= F81534_CONF_GPIO_SHUTDOWN) { /* * Newer IC configure will make transceiver in shutdown mode on * initial power on. We need enable it before using UARTs. */ idx = F81534_CONF_WORK_GPIO_OFFSET + port_priv->phy_num; value = serial_priv->conf_data[idx]; if (value >= F81534_CONF_GPIO_SHUTDOWN) value = F81534_CONF_GPIO_RS232; } pins = &f81534_port_out_pins[port_priv->phy_num]; for (i = 0; i < ARRAY_SIZE(pins->pin); ++i) { status = f81534_set_mask_register(serial, pins->pin[i].reg_addr, pins->pin[i].reg_mask, value & BIT(i) ? pins->pin[i].reg_mask : 0); if (status) return status; } dev_dbg(&port->dev, "Output pin (M0/M1/M2): %d\n", value); return 0; } static int f81534_port_probe(struct usb_serial_port *port) { struct f81534_serial_private *serial_priv; struct f81534_port_private *port_priv; int ret; u8 value; serial_priv = usb_get_serial_data(port->serial); port_priv = devm_kzalloc(&port->dev, sizeof(*port_priv), GFP_KERNEL); if (!port_priv) return -ENOMEM; /* * We'll make tx frame error when baud rate from 384~500kps. So we'll * delay all tx data frame with 1bit. */ port_priv->shadow_clk = F81534_UART_EN | F81534_CLK_TX_DELAY_1BIT; spin_lock_init(&port_priv->msr_lock); mutex_init(&port_priv->mcr_mutex); mutex_init(&port_priv->lcr_mutex); INIT_WORK(&port_priv->lsr_work, f81534_lsr_worker); /* Assign logic-to-phy mapping */ ret = f81534_logic_to_phy_port(port->serial, port); if (ret < 0) return ret; port_priv->phy_num = ret; port_priv->port = port; usb_set_serial_port_data(port, port_priv); dev_dbg(&port->dev, "%s: port_number: %d, phy_num: %d\n", __func__, port->port_number, port_priv->phy_num); /* * The F81532/534 will hang-up when enable LSR interrupt in IER and * occur data overrun. So we'll disable the LSR interrupt in probe() * and submit the LSR worker to clear LSR state when reported LSR error * bit with bulk-in data in f81534_process_per_serial_block(). */ ret = f81534_set_port_register(port, F81534_INTERRUPT_ENABLE_REG, UART_IER_RDI | UART_IER_THRI | UART_IER_MSI); if (ret) return ret; value = serial_priv->conf_data[port_priv->phy_num]; switch (value & F81534_PORT_CONF_MODE_MASK) { case F81534_PORT_CONF_RS485_INVERT: port_priv->shadow_clk |= F81534_CLK_RS485_MODE | F81534_CLK_RS485_INVERT; dev_dbg(&port->dev, "RS485 invert mode\n"); break; case F81534_PORT_CONF_RS485: port_priv->shadow_clk |= F81534_CLK_RS485_MODE; dev_dbg(&port->dev, "RS485 mode\n"); break; default: case F81534_PORT_CONF_RS232: dev_dbg(&port->dev, "RS232 mode\n"); break; } return f81534_set_port_output_pin(port); } static int f81534_port_remove(struct usb_serial_port *port) { struct f81534_port_private *port_priv = usb_get_serial_port_data(port); flush_work(&port_priv->lsr_work); return 0; } static int f81534_tiocmget(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; struct f81534_port_private *port_priv = usb_get_serial_port_data(port); int status; int r; u8 msr; u8 mcr; /* Read current MSR from device */ status = f81534_get_port_register(port, F81534_MODEM_STATUS_REG, &msr); if (status) return status; mutex_lock(&port_priv->mcr_mutex); mcr = port_priv->shadow_mcr; mutex_unlock(&port_priv->mcr_mutex); r = (mcr & UART_MCR_DTR ? TIOCM_DTR : 0) | (mcr & UART_MCR_RTS ? TIOCM_RTS : 0) | (msr & UART_MSR_CTS ? TIOCM_CTS : 0) | (msr & UART_MSR_DCD ? TIOCM_CAR : 0) | (msr & UART_MSR_RI ? TIOCM_RI : 0) | (msr & UART_MSR_DSR ? TIOCM_DSR : 0); return r; } static int f81534_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear) { struct usb_serial_port *port = tty->driver_data; return f81534_update_mctrl(port, set, clear); } static void f81534_dtr_rts(struct usb_serial_port *port, int on) { if (on) f81534_update_mctrl(port, TIOCM_DTR | TIOCM_RTS, 0); else f81534_update_mctrl(port, 0, TIOCM_DTR | TIOCM_RTS); } static int f81534_write(struct tty_struct *tty, struct usb_serial_port *port, const u8 *buf, int count) { int bytes_out, status; if (!count) return 0; bytes_out = kfifo_in_locked(&port->write_fifo, buf, count, &port->lock); status = f81534_submit_writer(port, GFP_ATOMIC); if (status) { dev_err(&port->dev, "%s: submit failed\n", __func__); return status; } return bytes_out; } static bool f81534_tx_empty(struct usb_serial_port *port) { struct f81534_port_private *port_priv = usb_get_serial_port_data(port); return test_bit(F81534_TX_EMPTY_BIT, &port_priv->tx_empty); } static int f81534_resume(struct usb_serial *serial) { struct f81534_serial_private *serial_priv = usb_get_serial_data(serial); struct usb_serial_port *port; int error = 0; int status; size_t i; /* * We'll register port 0 bulkin when port had opened, It'll take all * port received data, MSR register change and TX_EMPTY information. */ mutex_lock(&serial_priv->urb_mutex); if (serial_priv->opened_port) { status = f81534_submit_read_urb(serial, GFP_NOIO); if (status) { mutex_unlock(&serial_priv->urb_mutex); return status; } } mutex_unlock(&serial_priv->urb_mutex); for (i = 0; i < serial->num_ports; i++) { port = serial->port[i]; if (!tty_port_initialized(&port->port)) continue; status = f81534_submit_writer(port, GFP_NOIO); if (status) { dev_err(&port->dev, "%s: submit failed\n", __func__); ++error; } } if (error) return -EIO; return 0; } static struct usb_serial_driver f81534_device = { .driver = { .owner = THIS_MODULE, .name = "f81534", }, .description = DRIVER_DESC, .id_table = f81534_id_table, .num_bulk_in = 1, .num_bulk_out = 1, .open = f81534_open, .close = f81534_close, .write = f81534_write, .tx_empty = f81534_tx_empty, .calc_num_ports = f81534_calc_num_ports, .port_probe = f81534_port_probe, .port_remove = f81534_port_remove, .break_ctl = f81534_break_ctl, .dtr_rts = f81534_dtr_rts, .process_read_urb = f81534_process_read_urb, .get_serial = f81534_get_serial_info, .tiocmget = f81534_tiocmget, .tiocmset = f81534_tiocmset, .write_bulk_callback = f81534_write_usb_callback, .set_termios = f81534_set_termios, .resume = f81534_resume, }; static struct usb_serial_driver *const serial_drivers[] = { &f81534_device, NULL }; module_usb_serial_driver(serial_drivers, f81534_id_table); MODULE_DEVICE_TABLE(usb, f81534_id_table); MODULE_DESCRIPTION(DRIVER_DESC); MODULE_AUTHOR("Peter Hong "); MODULE_AUTHOR("Tom Tsai "); MODULE_LICENSE("GPL");