diff options
Diffstat (limited to '')
| -rw-r--r-- | doc/dev/network-protocol.rst | 197 |
1 files changed, 197 insertions, 0 deletions
diff --git a/doc/dev/network-protocol.rst b/doc/dev/network-protocol.rst new file mode 100644 index 00000000..f6fb1738 --- /dev/null +++ b/doc/dev/network-protocol.rst @@ -0,0 +1,197 @@ +================== + Network Protocol +================== + +This file describes the network protocol used by Ceph. In order to understand +the way the structures are defined it is recommended to read the introduction +of :doc:`/dev/network-encoding` first. + +Hello +===== + +The protocol starts with a handshake that confirms that both nodes are talking +ceph and shares some basic information. + +Banner +------ + +The first action is the server sending banner to the client. The banner is +defined in ``CEPH_BANNER`` from ``src/include/msgr.h``. This is followed by +the server's then client's address each encoded as a ``entity_addr_t``. + +Once the client verifies that the servers banner matches its own it replies with +its banner and its address. + +Connect +------- + +Once the banners have been verified and the addresses exchanged the connection +negotiation begins. First the client sends a ``ceph_msg_connect`` structure +with its information. + +:: + + // From src/include/msgr.h + struct ceph_msg_connect { + u64le features; // Supported features (CEPH_FEATURE_*) + u32le host_type; // CEPH_ENTITY_TYPE_* + u32le global_seq; // Number of connections initiated by this host. + u32le connect_seq; // Number of connections initiated in this session. + u32le protocol_version; + u32le authorizer_protocol; + u32le authorizer_len; + u8 flags; // CEPH_MSG_CONNECT_* + u8 authorizer[authorizer_len]; + } + +Connect Reply +------------- + +Once the connect has been sent the connection has effectively been opened, +however the first message the server sends must be a connect reply message. + +:: + + struct ceph_msg_connect_reply { + u8 tag; // Tag indicating response code. + u64le features; + u32le global_seq; + u32le connect_seq; + u32le protocol_version; + u32le authorizer_len; + u8 flags; + u8 authorizer[authorizer_len]; + } + +MSGR Protocol +============= + +This is a low level protocol over which messages are delivered. The messages +at this level consist of a tag byte, identifying the type of message, followed +by the message data. + +:: + + // Virtual structure. + struct { + u8 tag; // CEPH_MSGR_TAG_* + u8 data[]; // Length depends on tag and data. + } + +The length of ``data`` is determined by the tag byte and depending on the +message type via information in the ``data`` array itself. + +.. note:: + There is no way to determine the length of the message if you do not + understand the type of message. + +The message tags are defined in ``src/include/msgr.h`` and the current ones +are listed below along with the data they include. Note that the defined +structures don't exist in the source and are merely for representing the +protocol. + +CEPH_MSGR_TAG_CLOSE (0x06) +-------------------------- + +:: + + struct ceph_msgr_close { + u8 tag = 0x06; + u8 data[0]; // No data. + } + +The close message indicates that the connection is being closed. + +CEPH_MSGR_TAG_MSG (0x07) +------------------------ + +:: + + struct ceph_msgr_msg { + u8 tag = 0x07; + ceph_msg_header header; + u8 front [header.front_len ]; + u8 middle[header.middle_len]; + u8 data [header.data_len ]; + ceph_msg_footer footer; + } + + // From src/include/msgr.h + struct ceph_msg_header { + u64le seq; // Sequence number. + u64le tid; // Transaction ID. + u16le type; // Message type (CEPH_MSG_* or MSG_*). + u16le priority; // Priority (higher is more important). + u16le version; // Version of message encoding. + + u32le front_len; // The size of the front section. + u32le middle_len; // The size of the middle section. + u32le data_len; // The size of the data section. + u16le data_off; // The way data should be aligned by the receiver. + + ceph_entity_name src; // Information about the sender. + + u16le compat_version; // Oldest compatible encoding version. + u16le reserved; // Unused. + u32le crc; // CRC of header. + } + + // From src/include/msgr.h + struct ceph_msg_footer { + u32le front_crc; // Checksums of the various sections. + u32le middle_crc; // + u32le data_crc; // + u64le sig; // Crypographic signature. + u8 flags; + } + +Messages are the business logic of Ceph. They are what is used to send data and +requests between nodes. The message header contains the length of the message +so unknown messages can be handled gracefully. + +There are two names for the message type constants ``CEPH_MSG_*`` and ``MSG_*``. +The only difference between the two is that the first are considered "public" +while the second is for internal use only. There is no protocol-level +difference. + +CEPH_MSGR_TAG_ACK (0x08) +------------------------ + +:: + + struct ceph_msgr_ack { + u8 tag = 0x08; + u64le seq; // The sequence number of the message being acknowledged. + } + +CEPH_MSGR_TAG_KEEPALIVE (0x09) +------------------------------ + +:: + + struct ceph_msgr_keepalive { + u8 tag = 0x09; + u8 data[0]; // No data. + } + +CEPH_MSGR_TAG_KEEPALIVE2 (0x0E) +------------------------------- + +:: + + struct ceph_msgr_keepalive2 { + u8 tag = 0x0E; + utime_t timestamp; + } + +CEPH_MSGR_TAG_KEEPALIVE2_ACK (0x0F) +----------------------------------- + +:: + + struct ceph_msgr_keepalive2_ack { + u8 tag = 0x0F; + utime_t timestamp; + } + +.. vi: textwidth=80 noexpandtab |