diff options
Diffstat (limited to 'doc/rados/troubleshooting/troubleshooting-pg.rst')
| -rw-r--r-- | doc/rados/troubleshooting/troubleshooting-pg.rst | 666 |
1 files changed, 666 insertions, 0 deletions
diff --git a/doc/rados/troubleshooting/troubleshooting-pg.rst b/doc/rados/troubleshooting/troubleshooting-pg.rst new file mode 100644 index 00000000..a11b972f --- /dev/null +++ b/doc/rados/troubleshooting/troubleshooting-pg.rst @@ -0,0 +1,666 @@ +===================== + Troubleshooting PGs +===================== + +Placement Groups Never Get Clean +================================ + +When you create a cluster and your cluster remains in ``active``, +``active+remapped`` or ``active+degraded`` status and never achieve an +``active+clean`` status, you likely have a problem with your configuration. + +You may need to review settings in the `Pool, PG and CRUSH Config Reference`_ +and make appropriate adjustments. + +As a general rule, you should run your cluster with more than one OSD and a +pool size greater than 1 object replica. + +One Node Cluster +---------------- + +Ceph no longer provides documentation for operating on a single node, because +you would never deploy a system designed for distributed computing on a single +node. Additionally, mounting client kernel modules on a single node containing a +Ceph daemon may cause a deadlock due to issues with the Linux kernel itself +(unless you use VMs for the clients). You can experiment with Ceph in a 1-node +configuration, in spite of the limitations as described herein. + +If you are trying to create a cluster on a single node, you must change the +default of the ``osd crush chooseleaf type`` setting from ``1`` (meaning +``host`` or ``node``) to ``0`` (meaning ``osd``) in your Ceph configuration +file before you create your monitors and OSDs. This tells Ceph that an OSD +can peer with another OSD on the same host. If you are trying to set up a +1-node cluster and ``osd crush chooseleaf type`` is greater than ``0``, +Ceph will try to peer the PGs of one OSD with the PGs of another OSD on +another node, chassis, rack, row, or even datacenter depending on the setting. + +.. tip:: DO NOT mount kernel clients directly on the same node as your + Ceph Storage Cluster, because kernel conflicts can arise. However, you + can mount kernel clients within virtual machines (VMs) on a single node. + +If you are creating OSDs using a single disk, you must create directories +for the data manually first. For example:: + + ceph-deploy osd create --data {disk} {host} + + +Fewer OSDs than Replicas +------------------------ + +If you have brought up two OSDs to an ``up`` and ``in`` state, but you still +don't see ``active + clean`` placement groups, you may have an +``osd pool default size`` set to greater than ``2``. + +There are a few ways to address this situation. If you want to operate your +cluster in an ``active + degraded`` state with two replicas, you can set the +``osd pool default min size`` to ``2`` so that you can write objects in +an ``active + degraded`` state. You may also set the ``osd pool default size`` +setting to ``2`` so that you only have two stored replicas (the original and +one replica), in which case the cluster should achieve an ``active + clean`` +state. + +.. note:: You can make the changes at runtime. If you make the changes in + your Ceph configuration file, you may need to restart your cluster. + + +Pool Size = 1 +------------- + +If you have the ``osd pool default size`` set to ``1``, you will only have +one copy of the object. OSDs rely on other OSDs to tell them which objects +they should have. If a first OSD has a copy of an object and there is no +second copy, then no second OSD can tell the first OSD that it should have +that copy. For each placement group mapped to the first OSD (see +``ceph pg dump``), you can force the first OSD to notice the placement groups +it needs by running:: + + ceph osd force-create-pg <pgid> + + +CRUSH Map Errors +---------------- + +Another candidate for placement groups remaining unclean involves errors +in your CRUSH map. + + +Stuck Placement Groups +====================== + +It is normal for placement groups to enter states like "degraded" or "peering" +following a failure. Normally these states indicate the normal progression +through the failure recovery process. However, if a placement group stays in one +of these states for a long time this may be an indication of a larger problem. +For this reason, the monitor will warn when placement groups get "stuck" in a +non-optimal state. Specifically, we check for: + +* ``inactive`` - The placement group has not been ``active`` for too long + (i.e., it hasn't been able to service read/write requests). + +* ``unclean`` - The placement group has not been ``clean`` for too long + (i.e., it hasn't been able to completely recover from a previous failure). + +* ``stale`` - The placement group status has not been updated by a ``ceph-osd``, + indicating that all nodes storing this placement group may be ``down``. + +You can explicitly list stuck placement groups with one of:: + + ceph pg dump_stuck stale + ceph pg dump_stuck inactive + ceph pg dump_stuck unclean + +For stuck ``stale`` placement groups, it is normally a matter of getting the +right ``ceph-osd`` daemons running again. For stuck ``inactive`` placement +groups, it is usually a peering problem (see :ref:`failures-osd-peering`). For +stuck ``unclean`` placement groups, there is usually something preventing +recovery from completing, like unfound objects (see +:ref:`failures-osd-unfound`); + + + +.. _failures-osd-peering: + +Placement Group Down - Peering Failure +====================================== + +In certain cases, the ``ceph-osd`` `Peering` process can run into +problems, preventing a PG from becoming active and usable. For +example, ``ceph health`` might report:: + + ceph health detail + HEALTH_ERR 7 pgs degraded; 12 pgs down; 12 pgs peering; 1 pgs recovering; 6 pgs stuck unclean; 114/3300 degraded (3.455%); 1/3 in osds are down + ... + pg 0.5 is down+peering + pg 1.4 is down+peering + ... + osd.1 is down since epoch 69, last address 192.168.106.220:6801/8651 + +We can query the cluster to determine exactly why the PG is marked ``down`` with:: + + ceph pg 0.5 query + +.. code-block:: javascript + + { "state": "down+peering", + ... + "recovery_state": [ + { "name": "Started\/Primary\/Peering\/GetInfo", + "enter_time": "2012-03-06 14:40:16.169679", + "requested_info_from": []}, + { "name": "Started\/Primary\/Peering", + "enter_time": "2012-03-06 14:40:16.169659", + "probing_osds": [ + 0, + 1], + "blocked": "peering is blocked due to down osds", + "down_osds_we_would_probe": [ + 1], + "peering_blocked_by": [ + { "osd": 1, + "current_lost_at": 0, + "comment": "starting or marking this osd lost may let us proceed"}]}, + { "name": "Started", + "enter_time": "2012-03-06 14:40:16.169513"} + ] + } + +The ``recovery_state`` section tells us that peering is blocked due to +down ``ceph-osd`` daemons, specifically ``osd.1``. In this case, we can start that ``ceph-osd`` +and things will recover. + +Alternatively, if there is a catastrophic failure of ``osd.1`` (e.g., disk +failure), we can tell the cluster that it is ``lost`` and to cope as +best it can. + +.. important:: This is dangerous in that the cluster cannot + guarantee that the other copies of the data are consistent + and up to date. + +To instruct Ceph to continue anyway:: + + ceph osd lost 1 + +Recovery will proceed. + + +.. _failures-osd-unfound: + +Unfound Objects +=============== + +Under certain combinations of failures Ceph may complain about +``unfound`` objects:: + + ceph health detail + HEALTH_WARN 1 pgs degraded; 78/3778 unfound (2.065%) + pg 2.4 is active+degraded, 78 unfound + +This means that the storage cluster knows that some objects (or newer +copies of existing objects) exist, but it hasn't found copies of them. +One example of how this might come about for a PG whose data is on ceph-osds +1 and 2: + +* 1 goes down +* 2 handles some writes, alone +* 1 comes up +* 1 and 2 repeer, and the objects missing on 1 are queued for recovery. +* Before the new objects are copied, 2 goes down. + +Now 1 knows that these object exist, but there is no live ``ceph-osd`` who +has a copy. In this case, IO to those objects will block, and the +cluster will hope that the failed node comes back soon; this is +assumed to be preferable to returning an IO error to the user. + +First, you can identify which objects are unfound with:: + + ceph pg 2.4 list_unfound [starting offset, in json] + +.. code-block:: javascript + + { "offset": { "oid": "", + "key": "", + "snapid": 0, + "hash": 0, + "max": 0}, + "num_missing": 0, + "num_unfound": 0, + "objects": [ + { "oid": "object 1", + "key": "", + "hash": 0, + "max": 0 }, + ... + ], + "more": 0} + +If there are too many objects to list in a single result, the ``more`` +field will be true and you can query for more. (Eventually the +command line tool will hide this from you, but not yet.) + +Second, you can identify which OSDs have been probed or might contain +data:: + + ceph pg 2.4 query + +.. code-block:: javascript + + "recovery_state": [ + { "name": "Started\/Primary\/Active", + "enter_time": "2012-03-06 15:15:46.713212", + "might_have_unfound": [ + { "osd": 1, + "status": "osd is down"}]}, + +In this case, for example, the cluster knows that ``osd.1`` might have +data, but it is ``down``. The full range of possible states include: + +* already probed +* querying +* OSD is down +* not queried (yet) + +Sometimes it simply takes some time for the cluster to query possible +locations. + +It is possible that there are other locations where the object can +exist that are not listed. For example, if a ceph-osd is stopped and +taken out of the cluster, the cluster fully recovers, and due to some +future set of failures ends up with an unfound object, it won't +consider the long-departed ceph-osd as a potential location to +consider. (This scenario, however, is unlikely.) + +If all possible locations have been queried and objects are still +lost, you may have to give up on the lost objects. This, again, is +possible given unusual combinations of failures that allow the cluster +to learn about writes that were performed before the writes themselves +are recovered. To mark the "unfound" objects as "lost":: + + ceph pg 2.5 mark_unfound_lost revert|delete + +This the final argument specifies how the cluster should deal with +lost objects. + +The "delete" option will forget about them entirely. + +The "revert" option (not available for erasure coded pools) will +either roll back to a previous version of the object or (if it was a +new object) forget about it entirely. Use this with caution, as it +may confuse applications that expected the object to exist. + + +Homeless Placement Groups +========================= + +It is possible for all OSDs that had copies of a given placement groups to fail. +If that's the case, that subset of the object store is unavailable, and the +monitor will receive no status updates for those placement groups. To detect +this situation, the monitor marks any placement group whose primary OSD has +failed as ``stale``. For example:: + + ceph health + HEALTH_WARN 24 pgs stale; 3/300 in osds are down + +You can identify which placement groups are ``stale``, and what the last OSDs to +store them were, with:: + + ceph health detail + HEALTH_WARN 24 pgs stale; 3/300 in osds are down + ... + pg 2.5 is stuck stale+active+remapped, last acting [2,0] + ... + osd.10 is down since epoch 23, last address 192.168.106.220:6800/11080 + osd.11 is down since epoch 13, last address 192.168.106.220:6803/11539 + osd.12 is down since epoch 24, last address 192.168.106.220:6806/11861 + +If we want to get placement group 2.5 back online, for example, this tells us that +it was last managed by ``osd.0`` and ``osd.2``. Restarting those ``ceph-osd`` +daemons will allow the cluster to recover that placement group (and, presumably, +many others). + + +Only a Few OSDs Receive Data +============================ + +If you have many nodes in your cluster and only a few of them receive data, +`check`_ the number of placement groups in your pool. Since placement groups get +mapped to OSDs, a small number of placement groups will not distribute across +your cluster. Try creating a pool with a placement group count that is a +multiple of the number of OSDs. See `Placement Groups`_ for details. The default +placement group count for pools is not useful, but you can change it `here`_. + + +Can't Write Data +================ + +If your cluster is up, but some OSDs are down and you cannot write data, +check to ensure that you have the minimum number of OSDs running for the +placement group. If you don't have the minimum number of OSDs running, +Ceph will not allow you to write data because there is no guarantee +that Ceph can replicate your data. See ``osd pool default min size`` +in the `Pool, PG and CRUSH Config Reference`_ for details. + + +PGs Inconsistent +================ + +If you receive an ``active + clean + inconsistent`` state, this may happen +due to an error during scrubbing. As always, we can identify the inconsistent +placement group(s) with:: + + $ ceph health detail + HEALTH_ERR 1 pgs inconsistent; 2 scrub errors + pg 0.6 is active+clean+inconsistent, acting [0,1,2] + 2 scrub errors + +Or if you prefer inspecting the output in a programmatic way:: + + $ rados list-inconsistent-pg rbd + ["0.6"] + +There is only one consistent state, but in the worst case, we could have +different inconsistencies in multiple perspectives found in more than one +objects. If an object named ``foo`` in PG ``0.6`` is truncated, we will have:: + + $ rados list-inconsistent-obj 0.6 --format=json-pretty + +.. code-block:: javascript + + { + "epoch": 14, + "inconsistents": [ + { + "object": { + "name": "foo", + "nspace": "", + "locator": "", + "snap": "head", + "version": 1 + }, + "errors": [ + "data_digest_mismatch", + "size_mismatch" + ], + "union_shard_errors": [ + "data_digest_mismatch_info", + "size_mismatch_info" + ], + "selected_object_info": "0:602f83fe:::foo:head(16'1 client.4110.0:1 dirty|data_digest|omap_digest s 968 uv 1 dd e978e67f od ffffffff alloc_hint [0 0 0])", + "shards": [ + { + "osd": 0, + "errors": [], + "size": 968, + "omap_digest": "0xffffffff", + "data_digest": "0xe978e67f" + }, + { + "osd": 1, + "errors": [], + "size": 968, + "omap_digest": "0xffffffff", + "data_digest": "0xe978e67f" + }, + { + "osd": 2, + "errors": [ + "data_digest_mismatch_info", + "size_mismatch_info" + ], + "size": 0, + "omap_digest": "0xffffffff", + "data_digest": "0xffffffff" + } + ] + } + ] + } + +In this case, we can learn from the output: + +* The only inconsistent object is named ``foo``, and it is its head that has + inconsistencies. +* The inconsistencies fall into two categories: + + * ``errors``: these errors indicate inconsistencies between shards without a + determination of which shard(s) are bad. Check for the ``errors`` in the + `shards` array, if available, to pinpoint the problem. + + * ``data_digest_mismatch``: the digest of the replica read from OSD.2 is + different from the ones of OSD.0 and OSD.1 + * ``size_mismatch``: the size of the replica read from OSD.2 is 0, while + the size reported by OSD.0 and OSD.1 is 968. + * ``union_shard_errors``: the union of all shard specific ``errors`` in + ``shards`` array. The ``errors`` are set for the given shard that has the + problem. They include errors like ``read_error``. The ``errors`` ending in + ``oi`` indicate a comparison with ``selected_object_info``. Look at the + ``shards`` array to determine which shard has which error(s). + + * ``data_digest_mismatch_info``: the digest stored in the object-info is not + ``0xffffffff``, which is calculated from the shard read from OSD.2 + * ``size_mismatch_info``: the size stored in the object-info is different + from the one read from OSD.2. The latter is 0. + +You can repair the inconsistent placement group by executing:: + + ceph pg repair {placement-group-ID} + +Which overwrites the `bad` copies with the `authoritative` ones. In most cases, +Ceph is able to choose authoritative copies from all available replicas using +some predefined criteria. But this does not always work. For example, the stored +data digest could be missing, and the calculated digest will be ignored when +choosing the authoritative copies. So, please use the above command with caution. + +If ``read_error`` is listed in the ``errors`` attribute of a shard, the +inconsistency is likely due to disk errors. You might want to check your disk +used by that OSD. + +If you receive ``active + clean + inconsistent`` states periodically due to +clock skew, you may consider configuring your `NTP`_ daemons on your +monitor hosts to act as peers. See `The Network Time Protocol`_ and Ceph +`Clock Settings`_ for additional details. + + +Erasure Coded PGs are not active+clean +====================================== + +When CRUSH fails to find enough OSDs to map to a PG, it will show as a +``2147483647`` which is ITEM_NONE or ``no OSD found``. For instance:: + + [2,1,6,0,5,8,2147483647,7,4] + +Not enough OSDs +--------------- + +If the Ceph cluster only has 8 OSDs and the erasure coded pool needs +9, that is what it will show. You can either create another erasure +coded pool that requires less OSDs:: + + ceph osd erasure-code-profile set myprofile k=5 m=3 + ceph osd pool create erasurepool 16 16 erasure myprofile + +or add a new OSDs and the PG will automatically use them. + +CRUSH constraints cannot be satisfied +------------------------------------- + +If the cluster has enough OSDs, it is possible that the CRUSH rule +imposes constraints that cannot be satisfied. If there are 10 OSDs on +two hosts and the CRUSH rule requires that no two OSDs from the +same host are used in the same PG, the mapping may fail because only +two OSDs will be found. You can check the constraint by displaying ("dumping") +the rule:: + + $ ceph osd crush rule ls + [ + "replicated_rule", + "erasurepool"] + $ ceph osd crush rule dump erasurepool + { "rule_id": 1, + "rule_name": "erasurepool", + "ruleset": 1, + "type": 3, + "min_size": 3, + "max_size": 20, + "steps": [ + { "op": "take", + "item": -1, + "item_name": "default"}, + { "op": "chooseleaf_indep", + "num": 0, + "type": "host"}, + { "op": "emit"}]} + + +You can resolve the problem by creating a new pool in which PGs are allowed +to have OSDs residing on the same host with:: + + ceph osd erasure-code-profile set myprofile crush-failure-domain=osd + ceph osd pool create erasurepool 16 16 erasure myprofile + +CRUSH gives up too soon +----------------------- + +If the Ceph cluster has just enough OSDs to map the PG (for instance a +cluster with a total of 9 OSDs and an erasure coded pool that requires +9 OSDs per PG), it is possible that CRUSH gives up before finding a +mapping. It can be resolved by: + +* lowering the erasure coded pool requirements to use less OSDs per PG + (that requires the creation of another pool as erasure code profiles + cannot be dynamically modified). + +* adding more OSDs to the cluster (that does not require the erasure + coded pool to be modified, it will become clean automatically) + +* use a handmade CRUSH rule that tries more times to find a good + mapping. This can be done by setting ``set_choose_tries`` to a value + greater than the default. + +You should first verify the problem with ``crushtool`` after +extracting the crushmap from the cluster so your experiments do not +modify the Ceph cluster and only work on a local files:: + + $ ceph osd crush rule dump erasurepool + { "rule_name": "erasurepool", + "ruleset": 1, + "type": 3, + "min_size": 3, + "max_size": 20, + "steps": [ + { "op": "take", + "item": -1, + "item_name": "default"}, + { "op": "chooseleaf_indep", + "num": 0, + "type": "host"}, + { "op": "emit"}]} + $ ceph osd getcrushmap > crush.map + got crush map from osdmap epoch 13 + $ crushtool -i crush.map --test --show-bad-mappings \ + --rule 1 \ + --num-rep 9 \ + --min-x 1 --max-x $((1024 * 1024)) + bad mapping rule 8 x 43 num_rep 9 result [3,2,7,1,2147483647,8,5,6,0] + bad mapping rule 8 x 79 num_rep 9 result [6,0,2,1,4,7,2147483647,5,8] + bad mapping rule 8 x 173 num_rep 9 result [0,4,6,8,2,1,3,7,2147483647] + +Where ``--num-rep`` is the number of OSDs the erasure code CRUSH +rule needs, ``--rule`` is the value of the ``ruleset`` field +displayed by ``ceph osd crush rule dump``. The test will try mapping +one million values (i.e. the range defined by ``[--min-x,--max-x]``) +and must display at least one bad mapping. If it outputs nothing it +means all mappings are successful and you can stop right there: the +problem is elsewhere. + +The CRUSH rule can be edited by decompiling the crush map:: + + $ crushtool --decompile crush.map > crush.txt + +and adding the following line to the rule:: + + step set_choose_tries 100 + +The relevant part of of the ``crush.txt`` file should look something +like:: + + rule erasurepool { + ruleset 1 + type erasure + min_size 3 + max_size 20 + step set_chooseleaf_tries 5 + step set_choose_tries 100 + step take default + step chooseleaf indep 0 type host + step emit + } + +It can then be compiled and tested again:: + + $ crushtool --compile crush.txt -o better-crush.map + +When all mappings succeed, an histogram of the number of tries that +were necessary to find all of them can be displayed with the +``--show-choose-tries`` option of ``crushtool``:: + + $ crushtool -i better-crush.map --test --show-bad-mappings \ + --show-choose-tries \ + --rule 1 \ + --num-rep 9 \ + --min-x 1 --max-x $((1024 * 1024)) + ... + 11: 42 + 12: 44 + 13: 54 + 14: 45 + 15: 35 + 16: 34 + 17: 30 + 18: 25 + 19: 19 + 20: 22 + 21: 20 + 22: 17 + 23: 13 + 24: 16 + 25: 13 + 26: 11 + 27: 11 + 28: 13 + 29: 11 + 30: 10 + 31: 6 + 32: 5 + 33: 10 + 34: 3 + 35: 7 + 36: 5 + 37: 2 + 38: 5 + 39: 5 + 40: 2 + 41: 5 + 42: 4 + 43: 1 + 44: 2 + 45: 2 + 46: 3 + 47: 1 + 48: 0 + ... + 102: 0 + 103: 1 + 104: 0 + ... + +It took 11 tries to map 42 PGs, 12 tries to map 44 PGs etc. The highest number of tries is the minimum value of ``set_choose_tries`` that prevents bad mappings (i.e. 103 in the above output because it did not take more than 103 tries for any PG to be mapped). + +.. _check: ../../operations/placement-groups#get-the-number-of-placement-groups +.. _here: ../../configuration/pool-pg-config-ref +.. _Placement Groups: ../../operations/placement-groups +.. _Pool, PG and CRUSH Config Reference: ../../configuration/pool-pg-config-ref +.. _NTP: https://en.wikipedia.org/wiki/Network_Time_Protocol +.. _The Network Time Protocol: http://www.ntp.org/ +.. _Clock Settings: ../../configuration/mon-config-ref/#clock + + |