From 8e67fbf68ffeb9eb5f026dd482d73b021660bf9b Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sat, 27 Apr 2024 12:54:18 +0200 Subject: Adding debian version 2.06-3~deb11u6. Signed-off-by: Daniel Baumann --- .../gpxe/src/drivers/net/ath5k/ath5k_phy.c | 2586 ++++++++++++++++++++ 1 file changed, 2586 insertions(+) create mode 100644 debian/grub-extras/disabled/gpxe/src/drivers/net/ath5k/ath5k_phy.c (limited to 'debian/grub-extras/disabled/gpxe/src/drivers/net/ath5k/ath5k_phy.c') diff --git a/debian/grub-extras/disabled/gpxe/src/drivers/net/ath5k/ath5k_phy.c b/debian/grub-extras/disabled/gpxe/src/drivers/net/ath5k/ath5k_phy.c new file mode 100644 index 0000000..8856fa3 --- /dev/null +++ b/debian/grub-extras/disabled/gpxe/src/drivers/net/ath5k/ath5k_phy.c @@ -0,0 +1,2586 @@ +/* + * PHY functions + * + * Copyright (c) 2004-2007 Reyk Floeter + * Copyright (c) 2006-2009 Nick Kossifidis + * Copyright (c) 2007-2008 Jiri Slaby + * Copyright (c) 2008-2009 Felix Fietkau + * + * Lightly modified for gPXE, July 2009, by Joshua Oreman . + * + * Permission to use, copy, modify, and distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + * + */ + +FILE_LICENCE ( MIT ); + +#define _ATH5K_PHY + +#include +#include + +#include "ath5k.h" +#include "reg.h" +#include "base.h" +#include "rfbuffer.h" +#include "rfgain.h" + +static inline int min(int x, int y) +{ + return (x < y) ? x : y; +} + +static inline int max(int x, int y) +{ + return (x > y) ? x : y; +} + +/* + * Used to modify RF Banks before writing them to AR5K_RF_BUFFER + */ +static unsigned int ath5k_hw_rfb_op(struct ath5k_hw *ah, + const struct ath5k_rf_reg *rf_regs, + u32 val, u8 reg_id, int set) +{ + const struct ath5k_rf_reg *rfreg = NULL; + u8 offset, bank, num_bits, col, position; + u16 entry; + u32 mask, data, last_bit, bits_shifted, first_bit; + u32 *rfb; + s32 bits_left; + unsigned i; + + data = 0; + rfb = ah->ah_rf_banks; + + for (i = 0; i < ah->ah_rf_regs_count; i++) { + if (rf_regs[i].index == reg_id) { + rfreg = &rf_regs[i]; + break; + } + } + + if (rfb == NULL || rfreg == NULL) { + DBG("ath5k: RF register not found!\n"); + /* should not happen */ + return 0; + } + + bank = rfreg->bank; + num_bits = rfreg->field.len; + first_bit = rfreg->field.pos; + col = rfreg->field.col; + + /* first_bit is an offset from bank's + * start. Since we have all banks on + * the same array, we use this offset + * to mark each bank's start */ + offset = ah->ah_offset[bank]; + + /* Boundary check */ + if (!(col <= 3 && num_bits <= 32 && first_bit + num_bits <= 319)) { + DBG("ath5k: RF invalid values at offset %d\n", offset); + return 0; + } + + entry = ((first_bit - 1) / 8) + offset; + position = (first_bit - 1) % 8; + + if (set) + data = ath5k_hw_bitswap(val, num_bits); + + for (bits_shifted = 0, bits_left = num_bits; bits_left > 0; + position = 0, entry++) { + + last_bit = (position + bits_left > 8) ? 8 : + position + bits_left; + + mask = (((1 << last_bit) - 1) ^ ((1 << position) - 1)) << + (col * 8); + + if (set) { + rfb[entry] &= ~mask; + rfb[entry] |= ((data << position) << (col * 8)) & mask; + data >>= (8 - position); + } else { + data |= (((rfb[entry] & mask) >> (col * 8)) >> position) + << bits_shifted; + bits_shifted += last_bit - position; + } + + bits_left -= 8 - position; + } + + data = set ? 1 : ath5k_hw_bitswap(data, num_bits); + + return data; +} + +/**********************\ +* RF Gain optimization * +\**********************/ + +/* + * This code is used to optimize rf gain on different environments + * (temprature mostly) based on feedback from a power detector. + * + * It's only used on RF5111 and RF5112, later RF chips seem to have + * auto adjustment on hw -notice they have a much smaller BANK 7 and + * no gain optimization ladder-. + * + * For more infos check out this patent doc + * http://www.freepatentsonline.com/7400691.html + * + * This paper describes power drops as seen on the receiver due to + * probe packets + * http://www.cnri.dit.ie/publications/ICT08%20-%20Practical%20Issues + * %20of%20Power%20Control.pdf + * + * And this is the MadWiFi bug entry related to the above + * http://madwifi-project.org/ticket/1659 + * with various measurements and diagrams + * + * TODO: Deal with power drops due to probes by setting an apropriate + * tx power on the probe packets ! Make this part of the calibration process. + */ + +/* Initialize ah_gain durring attach */ +int ath5k_hw_rfgain_opt_init(struct ath5k_hw *ah) +{ + /* Initialize the gain optimization values */ + switch (ah->ah_radio) { + case AR5K_RF5111: + ah->ah_gain.g_step_idx = rfgain_opt_5111.go_default; + ah->ah_gain.g_low = 20; + ah->ah_gain.g_high = 35; + ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; + break; + case AR5K_RF5112: + ah->ah_gain.g_step_idx = rfgain_opt_5112.go_default; + ah->ah_gain.g_low = 20; + ah->ah_gain.g_high = 85; + ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; + break; + default: + return -EINVAL; + } + + return 0; +} + +/* Schedule a gain probe check on the next transmited packet. + * That means our next packet is going to be sent with lower + * tx power and a Peak to Average Power Detector (PAPD) will try + * to measure the gain. + * + * TODO: Use propper tx power setting for the probe packet so + * that we don't observe a serious power drop on the receiver + * + * XXX: How about forcing a tx packet (bypassing PCU arbitrator etc) + * just after we enable the probe so that we don't mess with + * standard traffic ? Maybe it's time to use sw interrupts and + * a probe tasklet !!! + */ +static void ath5k_hw_request_rfgain_probe(struct ath5k_hw *ah) +{ + + /* Skip if gain calibration is inactive or + * we already handle a probe request */ + if (ah->ah_gain.g_state != AR5K_RFGAIN_ACTIVE) + return; + + /* Send the packet with 2dB below max power as + * patent doc suggest */ + ath5k_hw_reg_write(ah, AR5K_REG_SM(ah->ah_txpower.txp_max_pwr - 4, + AR5K_PHY_PAPD_PROBE_TXPOWER) | + AR5K_PHY_PAPD_PROBE_TX_NEXT, AR5K_PHY_PAPD_PROBE); + + ah->ah_gain.g_state = AR5K_RFGAIN_READ_REQUESTED; + +} + +/* Calculate gain_F measurement correction + * based on the current step for RF5112 rev. 2 */ +static u32 ath5k_hw_rf_gainf_corr(struct ath5k_hw *ah) +{ + u32 mix, step; + u32 *rf; + const struct ath5k_gain_opt *go; + const struct ath5k_gain_opt_step *g_step; + const struct ath5k_rf_reg *rf_regs; + + /* Only RF5112 Rev. 2 supports it */ + if ((ah->ah_radio != AR5K_RF5112) || + (ah->ah_radio_5ghz_revision <= AR5K_SREV_RAD_5112A)) + return 0; + + go = &rfgain_opt_5112; + rf_regs = rf_regs_5112a; + ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112a); + + g_step = &go->go_step[ah->ah_gain.g_step_idx]; + + if (ah->ah_rf_banks == NULL) + return 0; + + rf = ah->ah_rf_banks; + ah->ah_gain.g_f_corr = 0; + + /* No VGA (Variable Gain Amplifier) override, skip */ + if (ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXVGA_OVR, 0) != 1) + return 0; + + /* Mix gain stepping */ + step = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXGAIN_STEP, 0); + + /* Mix gain override */ + mix = g_step->gos_param[0]; + + switch (mix) { + case 3: + ah->ah_gain.g_f_corr = step * 2; + break; + case 2: + ah->ah_gain.g_f_corr = (step - 5) * 2; + break; + case 1: + ah->ah_gain.g_f_corr = step; + break; + default: + ah->ah_gain.g_f_corr = 0; + break; + } + + return ah->ah_gain.g_f_corr; +} + +/* Check if current gain_F measurement is in the range of our + * power detector windows. If we get a measurement outside range + * we know it's not accurate (detectors can't measure anything outside + * their detection window) so we must ignore it */ +static int ath5k_hw_rf_check_gainf_readback(struct ath5k_hw *ah) +{ + const struct ath5k_rf_reg *rf_regs; + u32 step, mix_ovr, level[4]; + u32 *rf; + + if (ah->ah_rf_banks == NULL) + return 0; + + rf = ah->ah_rf_banks; + + if (ah->ah_radio == AR5K_RF5111) { + + rf_regs = rf_regs_5111; + ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5111); + + step = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_RFGAIN_STEP, + 0); + + level[0] = 0; + level[1] = (step == 63) ? 50 : step + 4; + level[2] = (step != 63) ? 64 : level[0]; + level[3] = level[2] + 50 ; + + ah->ah_gain.g_high = level[3] - + (step == 63 ? AR5K_GAIN_DYN_ADJUST_HI_MARGIN : -5); + ah->ah_gain.g_low = level[0] + + (step == 63 ? AR5K_GAIN_DYN_ADJUST_LO_MARGIN : 0); + } else { + + rf_regs = rf_regs_5112; + ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112); + + mix_ovr = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXVGA_OVR, + 0); + + level[0] = level[2] = 0; + + if (mix_ovr == 1) { + level[1] = level[3] = 83; + } else { + level[1] = level[3] = 107; + ah->ah_gain.g_high = 55; + } + } + + return (ah->ah_gain.g_current >= level[0] && + ah->ah_gain.g_current <= level[1]) || + (ah->ah_gain.g_current >= level[2] && + ah->ah_gain.g_current <= level[3]); +} + +/* Perform gain_F adjustment by choosing the right set + * of parameters from rf gain optimization ladder */ +static s8 ath5k_hw_rf_gainf_adjust(struct ath5k_hw *ah) +{ + const struct ath5k_gain_opt *go; + const struct ath5k_gain_opt_step *g_step; + int ret = 0; + + switch (ah->ah_radio) { + case AR5K_RF5111: + go = &rfgain_opt_5111; + break; + case AR5K_RF5112: + go = &rfgain_opt_5112; + break; + default: + return 0; + } + + g_step = &go->go_step[ah->ah_gain.g_step_idx]; + + if (ah->ah_gain.g_current >= ah->ah_gain.g_high) { + + /* Reached maximum */ + if (ah->ah_gain.g_step_idx == 0) + return -1; + + for (ah->ah_gain.g_target = ah->ah_gain.g_current; + ah->ah_gain.g_target >= ah->ah_gain.g_high && + ah->ah_gain.g_step_idx > 0; + g_step = &go->go_step[ah->ah_gain.g_step_idx]) + ah->ah_gain.g_target -= 2 * + (go->go_step[--(ah->ah_gain.g_step_idx)].gos_gain - + g_step->gos_gain); + + ret = 1; + goto done; + } + + if (ah->ah_gain.g_current <= ah->ah_gain.g_low) { + + /* Reached minimum */ + if (ah->ah_gain.g_step_idx == (go->go_steps_count - 1)) + return -2; + + for (ah->ah_gain.g_target = ah->ah_gain.g_current; + ah->ah_gain.g_target <= ah->ah_gain.g_low && + ah->ah_gain.g_step_idx < go->go_steps_count-1; + g_step = &go->go_step[ah->ah_gain.g_step_idx]) + ah->ah_gain.g_target -= 2 * + (go->go_step[++ah->ah_gain.g_step_idx].gos_gain - + g_step->gos_gain); + + ret = 2; + goto done; + } + +done: + DBG2("ath5k RF adjust: ret %d, gain step %d, current gain %d, " + "target gain %d\n", ret, ah->ah_gain.g_step_idx, + ah->ah_gain.g_current, ah->ah_gain.g_target); + + return ret; +} + +/* Main callback for thermal rf gain calibration engine + * Check for a new gain reading and schedule an adjustment + * if needed. + * + * TODO: Use sw interrupt to schedule reset if gain_F needs + * adjustment */ +enum ath5k_rfgain ath5k_hw_gainf_calibrate(struct ath5k_hw *ah) +{ + u32 data, type; + struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; + + if (ah->ah_rf_banks == NULL || + ah->ah_gain.g_state == AR5K_RFGAIN_INACTIVE) + return AR5K_RFGAIN_INACTIVE; + + /* No check requested, either engine is inactive + * or an adjustment is already requested */ + if (ah->ah_gain.g_state != AR5K_RFGAIN_READ_REQUESTED) + goto done; + + /* Read the PAPD (Peak to Average Power Detector) + * register */ + data = ath5k_hw_reg_read(ah, AR5K_PHY_PAPD_PROBE); + + /* No probe is scheduled, read gain_F measurement */ + if (!(data & AR5K_PHY_PAPD_PROBE_TX_NEXT)) { + ah->ah_gain.g_current = data >> AR5K_PHY_PAPD_PROBE_GAINF_S; + type = AR5K_REG_MS(data, AR5K_PHY_PAPD_PROBE_TYPE); + + /* If tx packet is CCK correct the gain_F measurement + * by cck ofdm gain delta */ + if (type == AR5K_PHY_PAPD_PROBE_TYPE_CCK) { + if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A) + ah->ah_gain.g_current += + ee->ee_cck_ofdm_gain_delta; + else + ah->ah_gain.g_current += + AR5K_GAIN_CCK_PROBE_CORR; + } + + /* Further correct gain_F measurement for + * RF5112A radios */ + if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A) { + ath5k_hw_rf_gainf_corr(ah); + ah->ah_gain.g_current = + ah->ah_gain.g_current >= ah->ah_gain.g_f_corr ? + (ah->ah_gain.g_current-ah->ah_gain.g_f_corr) : + 0; + } + + /* Check if measurement is ok and if we need + * to adjust gain, schedule a gain adjustment, + * else switch back to the acive state */ + if (ath5k_hw_rf_check_gainf_readback(ah) && + AR5K_GAIN_CHECK_ADJUST(&ah->ah_gain) && + ath5k_hw_rf_gainf_adjust(ah)) { + ah->ah_gain.g_state = AR5K_RFGAIN_NEED_CHANGE; + } else { + ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; + } + } + +done: + return ah->ah_gain.g_state; +} + +/* Write initial rf gain table to set the RF sensitivity + * this one works on all RF chips and has nothing to do + * with gain_F calibration */ +int ath5k_hw_rfgain_init(struct ath5k_hw *ah, unsigned int freq) +{ + const struct ath5k_ini_rfgain *ath5k_rfg; + unsigned int i, size; + + switch (ah->ah_radio) { + case AR5K_RF5111: + ath5k_rfg = rfgain_5111; + size = ARRAY_SIZE(rfgain_5111); + break; + case AR5K_RF5112: + ath5k_rfg = rfgain_5112; + size = ARRAY_SIZE(rfgain_5112); + break; + case AR5K_RF2413: + ath5k_rfg = rfgain_2413; + size = ARRAY_SIZE(rfgain_2413); + break; + case AR5K_RF2316: + ath5k_rfg = rfgain_2316; + size = ARRAY_SIZE(rfgain_2316); + break; + case AR5K_RF5413: + ath5k_rfg = rfgain_5413; + size = ARRAY_SIZE(rfgain_5413); + break; + case AR5K_RF2317: + case AR5K_RF2425: + ath5k_rfg = rfgain_2425; + size = ARRAY_SIZE(rfgain_2425); + break; + default: + return -EINVAL; + } + + switch (freq) { + case AR5K_INI_RFGAIN_2GHZ: + case AR5K_INI_RFGAIN_5GHZ: + break; + default: + return -EINVAL; + } + + for (i = 0; i < size; i++) { + AR5K_REG_WAIT(i); + ath5k_hw_reg_write(ah, ath5k_rfg[i].rfg_value[freq], + (u32)ath5k_rfg[i].rfg_register); + } + + return 0; +} + + + +/********************\ +* RF Registers setup * +\********************/ + + +/* + * Setup RF registers by writing rf buffer on hw + */ +int ath5k_hw_rfregs_init(struct ath5k_hw *ah, struct net80211_channel *channel, + unsigned int mode) +{ + const struct ath5k_rf_reg *rf_regs; + const struct ath5k_ini_rfbuffer *ini_rfb; + const struct ath5k_gain_opt *go = NULL; + const struct ath5k_gain_opt_step *g_step; + struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; + u8 ee_mode = 0; + u32 *rfb; + int obdb = -1, bank = -1; + unsigned i; + + switch (ah->ah_radio) { + case AR5K_RF5111: + rf_regs = rf_regs_5111; + ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5111); + ini_rfb = rfb_5111; + ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5111); + go = &rfgain_opt_5111; + break; + case AR5K_RF5112: + if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A) { + rf_regs = rf_regs_5112a; + ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112a); + ini_rfb = rfb_5112a; + ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5112a); + } else { + rf_regs = rf_regs_5112; + ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112); + ini_rfb = rfb_5112; + ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5112); + } + go = &rfgain_opt_5112; + break; + case AR5K_RF2413: + rf_regs = rf_regs_2413; + ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2413); + ini_rfb = rfb_2413; + ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2413); + break; + case AR5K_RF2316: + rf_regs = rf_regs_2316; + ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2316); + ini_rfb = rfb_2316; + ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2316); + break; + case AR5K_RF5413: + rf_regs = rf_regs_5413; + ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5413); + ini_rfb = rfb_5413; + ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5413); + break; + case AR5K_RF2317: + rf_regs = rf_regs_2425; + ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2425); + ini_rfb = rfb_2317; + ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2317); + break; + case AR5K_RF2425: + rf_regs = rf_regs_2425; + ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2425); + if (ah->ah_mac_srev < AR5K_SREV_AR2417) { + ini_rfb = rfb_2425; + ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2425); + } else { + ini_rfb = rfb_2417; + ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2417); + } + break; + default: + return -EINVAL; + } + + /* If it's the first time we set rf buffer, allocate + * ah->ah_rf_banks based on ah->ah_rf_banks_size + * we set above */ + if (ah->ah_rf_banks == NULL) { + ah->ah_rf_banks = malloc(sizeof(u32) * ah->ah_rf_banks_size); + if (ah->ah_rf_banks == NULL) { + return -ENOMEM; + } + } + + /* Copy values to modify them */ + rfb = ah->ah_rf_banks; + + for (i = 0; i < ah->ah_rf_banks_size; i++) { + if (ini_rfb[i].rfb_bank >= AR5K_MAX_RF_BANKS) { + DBG("ath5k: invalid RF register bank\n"); + return -EINVAL; + } + + /* Bank changed, write down the offset */ + if (bank != ini_rfb[i].rfb_bank) { + bank = ini_rfb[i].rfb_bank; + ah->ah_offset[bank] = i; + } + + rfb[i] = ini_rfb[i].rfb_mode_data[mode]; + } + + /* Set Output and Driver bias current (OB/DB) */ + if (channel->hw_value & CHANNEL_2GHZ) { + + if (channel->hw_value & CHANNEL_CCK) + ee_mode = AR5K_EEPROM_MODE_11B; + else + ee_mode = AR5K_EEPROM_MODE_11G; + + /* For RF511X/RF211X combination we + * use b_OB and b_DB parameters stored + * in eeprom on ee->ee_ob[ee_mode][0] + * + * For all other chips we use OB/DB for 2Ghz + * stored in the b/g modal section just like + * 802.11a on ee->ee_ob[ee_mode][1] */ + if ((ah->ah_radio == AR5K_RF5111) || + (ah->ah_radio == AR5K_RF5112)) + obdb = 0; + else + obdb = 1; + + ath5k_hw_rfb_op(ah, rf_regs, ee->ee_ob[ee_mode][obdb], + AR5K_RF_OB_2GHZ, 1); + + ath5k_hw_rfb_op(ah, rf_regs, ee->ee_db[ee_mode][obdb], + AR5K_RF_DB_2GHZ, 1); + + /* RF5111 always needs OB/DB for 5GHz, even if we use 2GHz */ + } else if ((channel->hw_value & CHANNEL_5GHZ) || + (ah->ah_radio == AR5K_RF5111)) { + + /* For 11a, Turbo and XR we need to choose + * OB/DB based on frequency range */ + ee_mode = AR5K_EEPROM_MODE_11A; + obdb = channel->center_freq >= 5725 ? 3 : + (channel->center_freq >= 5500 ? 2 : + (channel->center_freq >= 5260 ? 1 : + (channel->center_freq > 4000 ? 0 : -1))); + + if (obdb < 0) + return -EINVAL; + + ath5k_hw_rfb_op(ah, rf_regs, ee->ee_ob[ee_mode][obdb], + AR5K_RF_OB_5GHZ, 1); + + ath5k_hw_rfb_op(ah, rf_regs, ee->ee_db[ee_mode][obdb], + AR5K_RF_DB_5GHZ, 1); + } + + g_step = &go->go_step[ah->ah_gain.g_step_idx]; + + /* Bank Modifications (chip-specific) */ + if (ah->ah_radio == AR5K_RF5111) { + + /* Set gain_F settings according to current step */ + if (channel->hw_value & CHANNEL_OFDM) { + + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_FRAME_CTL, + AR5K_PHY_FRAME_CTL_TX_CLIP, + g_step->gos_param[0]); + + ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[1], + AR5K_RF_PWD_90, 1); + + ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[2], + AR5K_RF_PWD_84, 1); + + ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[3], + AR5K_RF_RFGAIN_SEL, 1); + + /* We programmed gain_F parameters, switch back + * to active state */ + ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; + + } + + /* Bank 6/7 setup */ + + ath5k_hw_rfb_op(ah, rf_regs, !ee->ee_xpd[ee_mode], + AR5K_RF_PWD_XPD, 1); + + ath5k_hw_rfb_op(ah, rf_regs, ee->ee_x_gain[ee_mode], + AR5K_RF_XPD_GAIN, 1); + + ath5k_hw_rfb_op(ah, rf_regs, ee->ee_i_gain[ee_mode], + AR5K_RF_GAIN_I, 1); + + ath5k_hw_rfb_op(ah, rf_regs, ee->ee_xpd[ee_mode], + AR5K_RF_PLO_SEL, 1); + + /* TODO: Half/quarter channel support */ + } + + if (ah->ah_radio == AR5K_RF5112) { + + /* Set gain_F settings according to current step */ + if (channel->hw_value & CHANNEL_OFDM) { + + ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[0], + AR5K_RF_MIXGAIN_OVR, 1); + + ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[1], + AR5K_RF_PWD_138, 1); + + ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[2], + AR5K_RF_PWD_137, 1); + + ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[3], + AR5K_RF_PWD_136, 1); + + ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[4], + AR5K_RF_PWD_132, 1); + + ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[5], + AR5K_RF_PWD_131, 1); + + ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[6], + AR5K_RF_PWD_130, 1); + + /* We programmed gain_F parameters, switch back + * to active state */ + ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; + } + + /* Bank 6/7 setup */ + + ath5k_hw_rfb_op(ah, rf_regs, ee->ee_xpd[ee_mode], + AR5K_RF_XPD_SEL, 1); + + if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_5112A) { + /* Rev. 1 supports only one xpd */ + ath5k_hw_rfb_op(ah, rf_regs, + ee->ee_x_gain[ee_mode], + AR5K_RF_XPD_GAIN, 1); + + } else { + /* TODO: Set high and low gain bits */ + ath5k_hw_rfb_op(ah, rf_regs, + ee->ee_x_gain[ee_mode], + AR5K_RF_PD_GAIN_LO, 1); + ath5k_hw_rfb_op(ah, rf_regs, + ee->ee_x_gain[ee_mode], + AR5K_RF_PD_GAIN_HI, 1); + + /* Lower synth voltage on Rev 2 */ + ath5k_hw_rfb_op(ah, rf_regs, 2, + AR5K_RF_HIGH_VC_CP, 1); + + ath5k_hw_rfb_op(ah, rf_regs, 2, + AR5K_RF_MID_VC_CP, 1); + + ath5k_hw_rfb_op(ah, rf_regs, 2, + AR5K_RF_LOW_VC_CP, 1); + + ath5k_hw_rfb_op(ah, rf_regs, 2, + AR5K_RF_PUSH_UP, 1); + + /* Decrease power consumption on 5213+ BaseBand */ + if (ah->ah_phy_revision >= AR5K_SREV_PHY_5212A) { + ath5k_hw_rfb_op(ah, rf_regs, 1, + AR5K_RF_PAD2GND, 1); + + ath5k_hw_rfb_op(ah, rf_regs, 1, + AR5K_RF_XB2_LVL, 1); + + ath5k_hw_rfb_op(ah, rf_regs, 1, + AR5K_RF_XB5_LVL, 1); + + ath5k_hw_rfb_op(ah, rf_regs, 1, + AR5K_RF_PWD_167, 1); + + ath5k_hw_rfb_op(ah, rf_regs, 1, + AR5K_RF_PWD_166, 1); + } + } + + ath5k_hw_rfb_op(ah, rf_regs, ee->ee_i_gain[ee_mode], + AR5K_RF_GAIN_I, 1); + + /* TODO: Half/quarter channel support */ + + } + + if (ah->ah_radio == AR5K_RF5413 && + channel->hw_value & CHANNEL_2GHZ) { + + ath5k_hw_rfb_op(ah, rf_regs, 1, AR5K_RF_DERBY_CHAN_SEL_MODE, + 1); + + /* Set optimum value for early revisions (on pci-e chips) */ + if (ah->ah_mac_srev >= AR5K_SREV_AR5424 && + ah->ah_mac_srev < AR5K_SREV_AR5413) + ath5k_hw_rfb_op(ah, rf_regs, ath5k_hw_bitswap(6, 3), + AR5K_RF_PWD_ICLOBUF_2G, 1); + + } + + /* Write RF banks on hw */ + for (i = 0; i < ah->ah_rf_banks_size; i++) { + AR5K_REG_WAIT(i); + ath5k_hw_reg_write(ah, rfb[i], ini_rfb[i].rfb_ctrl_register); + } + + return 0; +} + + +/**************************\ + PHY/RF channel functions +\**************************/ + +/* + * Check if a channel is supported + */ +int ath5k_channel_ok(struct ath5k_hw *ah, u16 freq, unsigned int flags) +{ + /* Check if the channel is in our supported range */ + if (flags & CHANNEL_2GHZ) { + if ((freq >= ah->ah_capabilities.cap_range.range_2ghz_min) && + (freq <= ah->ah_capabilities.cap_range.range_2ghz_max)) + return 1; + } else if (flags & CHANNEL_5GHZ) + if ((freq >= ah->ah_capabilities.cap_range.range_5ghz_min) && + (freq <= ah->ah_capabilities.cap_range.range_5ghz_max)) + return 1; + + return 0; +} + +/* + * Convertion needed for RF5110 + */ +static u32 ath5k_hw_rf5110_chan2athchan(struct net80211_channel *channel) +{ + u32 athchan; + + /* + * Convert IEEE channel/MHz to an internal channel value used + * by the AR5210 chipset. This has not been verified with + * newer chipsets like the AR5212A who have a completely + * different RF/PHY part. + */ + athchan = (ath5k_hw_bitswap((ath5k_freq_to_channel(channel->center_freq) + - 24) / 2, 5) << 1) + | (1 << 6) | 0x1; + return athchan; +} + +/* + * Set channel on RF5110 + */ +static int ath5k_hw_rf5110_channel(struct ath5k_hw *ah, + struct net80211_channel *channel) +{ + u32 data; + + /* + * Set the channel and wait + */ + data = ath5k_hw_rf5110_chan2athchan(channel); + ath5k_hw_reg_write(ah, data, AR5K_RF_BUFFER); + ath5k_hw_reg_write(ah, 0, AR5K_RF_BUFFER_CONTROL_0); + mdelay(1); + + return 0; +} + +/* + * Convertion needed for 5111 + */ +static int ath5k_hw_rf5111_chan2athchan(unsigned int ieee, + struct ath5k_athchan_2ghz *athchan) +{ + int channel; + + /* Cast this value to catch negative channel numbers (>= -19) */ + channel = (int)ieee; + + /* + * Map 2GHz IEEE channel to 5GHz Atheros channel + */ + if (channel <= 13) { + athchan->a2_athchan = 115 + channel; + athchan->a2_flags = 0x46; + } else if (channel == 14) { + athchan->a2_athchan = 124; + athchan->a2_flags = 0x44; + } else if (channel >= 15 && channel <= 26) { + athchan->a2_athchan = ((channel - 14) * 4) + 132; + athchan->a2_flags = 0x46; + } else + return -EINVAL; + + return 0; +} + +/* + * Set channel on 5111 + */ +static int ath5k_hw_rf5111_channel(struct ath5k_hw *ah, + struct net80211_channel *channel) +{ + struct ath5k_athchan_2ghz ath5k_channel_2ghz; + unsigned int ath5k_channel = ath5k_freq_to_channel(channel->center_freq); + u32 data0, data1, clock; + int ret; + + /* + * Set the channel on the RF5111 radio + */ + data0 = data1 = 0; + + if (channel->hw_value & CHANNEL_2GHZ) { + /* Map 2GHz channel to 5GHz Atheros channel ID */ + ret = ath5k_hw_rf5111_chan2athchan(ath5k_channel, + &ath5k_channel_2ghz); + if (ret) + return ret; + + ath5k_channel = ath5k_channel_2ghz.a2_athchan; + data0 = ((ath5k_hw_bitswap(ath5k_channel_2ghz.a2_flags, 8) & 0xff) + << 5) | (1 << 4); + } + + if (ath5k_channel < 145 || !(ath5k_channel & 1)) { + clock = 1; + data1 = ((ath5k_hw_bitswap(ath5k_channel - 24, 8) & 0xff) << 2) | + (clock << 1) | (1 << 10) | 1; + } else { + clock = 0; + data1 = ((ath5k_hw_bitswap((ath5k_channel - 24) / 2, 8) & 0xff) + << 2) | (clock << 1) | (1 << 10) | 1; + } + + ath5k_hw_reg_write(ah, (data1 & 0xff) | ((data0 & 0xff) << 8), + AR5K_RF_BUFFER); + ath5k_hw_reg_write(ah, ((data1 >> 8) & 0xff) | (data0 & 0xff00), + AR5K_RF_BUFFER_CONTROL_3); + + return 0; +} + +/* + * Set channel on 5112 and newer + */ +static int ath5k_hw_rf5112_channel(struct ath5k_hw *ah, + struct net80211_channel *channel) +{ + u32 data, data0, data1, data2; + u16 c; + + data = data0 = data1 = data2 = 0; + c = channel->center_freq; + + if (c < 4800) { + if (!((c - 2224) % 5)) { + data0 = ((2 * (c - 704)) - 3040) / 10; + data1 = 1; + } else if (!((c - 2192) % 5)) { + data0 = ((2 * (c - 672)) - 3040) / 10; + data1 = 0; + } else + return -EINVAL; + + data0 = ath5k_hw_bitswap((data0 << 2) & 0xff, 8); + } else if ((c - (c % 5)) != 2 || c > 5435) { + if (!(c % 20) && c >= 5120) { + data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8); + data2 = ath5k_hw_bitswap(3, 2); + } else if (!(c % 10)) { + data0 = ath5k_hw_bitswap(((c - 4800) / 10 << 1), 8); + data2 = ath5k_hw_bitswap(2, 2); + } else if (!(c % 5)) { + data0 = ath5k_hw_bitswap((c - 4800) / 5, 8); + data2 = ath5k_hw_bitswap(1, 2); + } else + return -EINVAL; + } else { + data0 = ath5k_hw_bitswap((10 * (c - 2) - 4800) / 25 + 1, 8); + data2 = ath5k_hw_bitswap(0, 2); + } + + data = (data0 << 4) | (data1 << 1) | (data2 << 2) | 0x1001; + + ath5k_hw_reg_write(ah, data & 0xff, AR5K_RF_BUFFER); + ath5k_hw_reg_write(ah, (data >> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5); + + return 0; +} + +/* + * Set the channel on the RF2425 + */ +static int ath5k_hw_rf2425_channel(struct ath5k_hw *ah, + struct net80211_channel *channel) +{ + u32 data, data0, data2; + u16 c; + + data = data0 = data2 = 0; + c = channel->center_freq; + + if (c < 4800) { + data0 = ath5k_hw_bitswap((c - 2272), 8); + data2 = 0; + /* ? 5GHz ? */ + } else if ((c - (c % 5)) != 2 || c > 5435) { + if (!(c % 20) && c < 5120) + data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8); + else if (!(c % 10)) + data0 = ath5k_hw_bitswap(((c - 4800) / 10 << 1), 8); + else if (!(c % 5)) + data0 = ath5k_hw_bitswap((c - 4800) / 5, 8); + else + return -EINVAL; + data2 = ath5k_hw_bitswap(1, 2); + } else { + data0 = ath5k_hw_bitswap((10 * (c - 2) - 4800) / 25 + 1, 8); + data2 = ath5k_hw_bitswap(0, 2); + } + + data = (data0 << 4) | data2 << 2 | 0x1001; + + ath5k_hw_reg_write(ah, data & 0xff, AR5K_RF_BUFFER); + ath5k_hw_reg_write(ah, (data >> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5); + + return 0; +} + +/* + * Set a channel on the radio chip + */ +int ath5k_hw_channel(struct ath5k_hw *ah, struct net80211_channel *channel) +{ + int ret; + /* + * Check bounds supported by the PHY (we don't care about regultory + * restrictions at this point). Note: hw_value already has the band + * (CHANNEL_2GHZ, or CHANNEL_5GHZ) so we inform ath5k_channel_ok() + * of the band by that */ + if (!ath5k_channel_ok(ah, channel->center_freq, channel->hw_value)) { + DBG("ath5k: channel frequency (%d MHz) out of supported " + "range\n", channel->center_freq); + return -EINVAL; + } + + /* + * Set the channel and wait + */ + switch (ah->ah_radio) { + case AR5K_RF5110: + ret = ath5k_hw_rf5110_channel(ah, channel); + break; + case AR5K_RF5111: + ret = ath5k_hw_rf5111_channel(ah, channel); + break; + case AR5K_RF2425: + ret = ath5k_hw_rf2425_channel(ah, channel); + break; + default: + ret = ath5k_hw_rf5112_channel(ah, channel); + break; + } + + if (ret) { + DBG("ath5k: setting channel failed: %s\n", strerror(ret)); + return ret; + } + + /* Set JAPAN setting for channel 14 */ + if (channel->center_freq == 2484) { + AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL, + AR5K_PHY_CCKTXCTL_JAPAN); + } else { + AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL, + AR5K_PHY_CCKTXCTL_WORLD); + } + + ah->ah_current_channel = channel; + ah->ah_turbo = (channel->hw_value == CHANNEL_T ? 1 : 0); + + return 0; +} + +/*****************\ + PHY calibration +\*****************/ + +/** + * ath5k_hw_noise_floor_calibration - perform PHY noise floor calibration + * + * @ah: struct ath5k_hw pointer we are operating on + * @freq: the channel frequency, just used for error logging + * + * This function performs a noise floor calibration of the PHY and waits for + * it to complete. Then the noise floor value is compared to some maximum + * noise floor we consider valid. + * + * Note that this is different from what the madwifi HAL does: it reads the + * noise floor and afterwards initiates the calibration. Since the noise floor + * calibration can take some time to finish, depending on the current channel + * use, that avoids the occasional timeout warnings we are seeing now. + * + * See the following link for an Atheros patent on noise floor calibration: + * http://patft.uspto.gov/netacgi/nph-Parser?Sect1=PTO1&Sect2=HITOFF&d=PALL \ + * &p=1&u=%2Fnetahtml%2FPTO%2Fsrchnum.htm&r=1&f=G&l=50&s1=7245893.PN.&OS=PN/7 + * + * XXX: Since during noise floor calibration antennas are detached according to + * the patent, we should stop tx queues here. + */ +int +ath5k_hw_noise_floor_calibration(struct ath5k_hw *ah, short freq) +{ + int ret; + unsigned int i; + s32 noise_floor; + + /* + * Enable noise floor calibration + */ + AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, + AR5K_PHY_AGCCTL_NF); + + ret = ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL, + AR5K_PHY_AGCCTL_NF, 0, 0); + + if (ret) { + DBG("ath5k: noise floor calibration timeout (%d MHz)\n", freq); + return -EAGAIN; + } + + /* Wait until the noise floor is calibrated and read the value */ + for (i = 20; i > 0; i--) { + mdelay(1); + noise_floor = ath5k_hw_reg_read(ah, AR5K_PHY_NF); + noise_floor = AR5K_PHY_NF_RVAL(noise_floor); + if (noise_floor & AR5K_PHY_NF_ACTIVE) { + noise_floor = AR5K_PHY_NF_AVAL(noise_floor); + + if (noise_floor <= AR5K_TUNE_NOISE_FLOOR) + break; + } + } + + DBG2("ath5k: noise floor %d\n", noise_floor); + + if (noise_floor > AR5K_TUNE_NOISE_FLOOR) { + DBG("ath5k: noise floor calibration failed (%d MHz)\n", freq); + return -EAGAIN; + } + + ah->ah_noise_floor = noise_floor; + + return 0; +} + +/* + * Perform a PHY calibration on RF5110 + * -Fix BPSK/QAM Constellation (I/Q correction) + * -Calculate Noise Floor + */ +static int ath5k_hw_rf5110_calibrate(struct ath5k_hw *ah, + struct net80211_channel *channel) +{ + u32 phy_sig, phy_agc, phy_sat, beacon; + int ret; + + /* + * Disable beacons and RX/TX queues, wait + */ + AR5K_REG_ENABLE_BITS(ah, AR5K_DIAG_SW_5210, + AR5K_DIAG_SW_DIS_TX | AR5K_DIAG_SW_DIS_RX_5210); + beacon = ath5k_hw_reg_read(ah, AR5K_BEACON_5210); + ath5k_hw_reg_write(ah, beacon & ~AR5K_BEACON_ENABLE, AR5K_BEACON_5210); + + mdelay(2); + + /* + * Set the channel (with AGC turned off) + */ + AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); + udelay(10); + ret = ath5k_hw_channel(ah, channel); + + /* + * Activate PHY and wait + */ + ath5k_hw_reg_write(ah, AR5K_PHY_ACT_ENABLE, AR5K_PHY_ACT); + mdelay(1); + + AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); + + if (ret) + return ret; + + /* + * Calibrate the radio chip + */ + + /* Remember normal state */ + phy_sig = ath5k_hw_reg_read(ah, AR5K_PHY_SIG); + phy_agc = ath5k_hw_reg_read(ah, AR5K_PHY_AGCCOARSE); + phy_sat = ath5k_hw_reg_read(ah, AR5K_PHY_ADCSAT); + + /* Update radio registers */ + ath5k_hw_reg_write(ah, (phy_sig & ~(AR5K_PHY_SIG_FIRPWR)) | + AR5K_REG_SM(-1, AR5K_PHY_SIG_FIRPWR), AR5K_PHY_SIG); + + ath5k_hw_reg_write(ah, (phy_agc & ~(AR5K_PHY_AGCCOARSE_HI | + AR5K_PHY_AGCCOARSE_LO)) | + AR5K_REG_SM(-1, AR5K_PHY_AGCCOARSE_HI) | + AR5K_REG_SM(-127, AR5K_PHY_AGCCOARSE_LO), AR5K_PHY_AGCCOARSE); + + ath5k_hw_reg_write(ah, (phy_sat & ~(AR5K_PHY_ADCSAT_ICNT | + AR5K_PHY_ADCSAT_THR)) | + AR5K_REG_SM(2, AR5K_PHY_ADCSAT_ICNT) | + AR5K_REG_SM(12, AR5K_PHY_ADCSAT_THR), AR5K_PHY_ADCSAT); + + udelay(20); + + AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); + udelay(10); + ath5k_hw_reg_write(ah, AR5K_PHY_RFSTG_DISABLE, AR5K_PHY_RFSTG); + AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); + + mdelay(1); + + /* + * Enable calibration and wait until completion + */ + AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, AR5K_PHY_AGCCTL_CAL); + + ret = ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL, + AR5K_PHY_AGCCTL_CAL, 0, 0); + + /* Reset to normal state */ + ath5k_hw_reg_write(ah, phy_sig, AR5K_PHY_SIG); + ath5k_hw_reg_write(ah, phy_agc, AR5K_PHY_AGCCOARSE); + ath5k_hw_reg_write(ah, phy_sat, AR5K_PHY_ADCSAT); + + if (ret) { + DBG("ath5k: calibration timeout (%d MHz)\n", + channel->center_freq); + return ret; + } + + ath5k_hw_noise_floor_calibration(ah, channel->center_freq); + + /* + * Re-enable RX/TX and beacons + */ + AR5K_REG_DISABLE_BITS(ah, AR5K_DIAG_SW_5210, + AR5K_DIAG_SW_DIS_TX | AR5K_DIAG_SW_DIS_RX_5210); + ath5k_hw_reg_write(ah, beacon, AR5K_BEACON_5210); + + return 0; +} + +/* + * Perform a PHY calibration on RF5111/5112 and newer chips + */ +static int ath5k_hw_rf511x_calibrate(struct ath5k_hw *ah, + struct net80211_channel *channel) +{ + u32 i_pwr, q_pwr; + s32 iq_corr, i_coff, i_coffd, q_coff, q_coffd; + int i; + + if (!ah->ah_calibration || + ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN) + goto done; + + /* Calibration has finished, get the results and re-run */ + for (i = 0; i <= 10; i++) { + iq_corr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_CORR); + i_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_I); + q_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_Q); + } + + i_coffd = ((i_pwr >> 1) + (q_pwr >> 1)) >> 7; + q_coffd = q_pwr >> 7; + + /* No correction */ + if (i_coffd == 0 || q_coffd == 0) + goto done; + + i_coff = ((-iq_corr) / i_coffd) & 0x3f; + + /* Boundary check */ + if (i_coff > 31) + i_coff = 31; + if (i_coff < -32) + i_coff = -32; + + q_coff = (((s32)i_pwr / q_coffd) - 128) & 0x1f; + + /* Boundary check */ + if (q_coff > 15) + q_coff = 15; + if (q_coff < -16) + q_coff = -16; + + /* Commit new I/Q value */ + AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_ENABLE | + ((u32)q_coff) | ((u32)i_coff << AR5K_PHY_IQ_CORR_Q_I_COFF_S)); + + /* Re-enable calibration -if we don't we'll commit + * the same values again and again */ + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ, + AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15); + AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_RUN); + +done: + + /* TODO: Separate noise floor calibration from I/Q calibration + * since noise floor calibration interrupts rx path while I/Q + * calibration doesn't. We don't need to run noise floor calibration + * as often as I/Q calibration.*/ + ath5k_hw_noise_floor_calibration(ah, channel->center_freq); + + /* Initiate a gain_F calibration */ + ath5k_hw_request_rfgain_probe(ah); + + return 0; +} + +/* + * Perform a PHY calibration + */ +int ath5k_hw_phy_calibrate(struct ath5k_hw *ah, + struct net80211_channel *channel) +{ + int ret; + + if (ah->ah_radio == AR5K_RF5110) + ret = ath5k_hw_rf5110_calibrate(ah, channel); + else + ret = ath5k_hw_rf511x_calibrate(ah, channel); + + return ret; +} + +int ath5k_hw_phy_disable(struct ath5k_hw *ah) +{ + ath5k_hw_reg_write(ah, AR5K_PHY_ACT_DISABLE, AR5K_PHY_ACT); + + return 0; +} + +/********************\ + Misc PHY functions +\********************/ + +/* + * Get the PHY Chip revision + */ +u16 ath5k_hw_radio_revision(struct ath5k_hw *ah, unsigned int chan) +{ + unsigned int i; + u32 srev; + u16 ret; + + /* + * Set the radio chip access register + */ + switch (chan) { + case CHANNEL_2GHZ: + ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_2GHZ, AR5K_PHY(0)); + break; + case CHANNEL_5GHZ: + ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0)); + break; + default: + return 0; + } + + mdelay(2); + + /* ...wait until PHY is ready and read the selected radio revision */ + ath5k_hw_reg_write(ah, 0x00001c16, AR5K_PHY(0x34)); + + for (i = 0; i < 8; i++) + ath5k_hw_reg_write(ah, 0x00010000, AR5K_PHY(0x20)); + + if (ah->ah_version == AR5K_AR5210) { + srev = ath5k_hw_reg_read(ah, AR5K_PHY(256) >> 28) & 0xf; + ret = (u16)ath5k_hw_bitswap(srev, 4) + 1; + } else { + srev = (ath5k_hw_reg_read(ah, AR5K_PHY(0x100)) >> 24) & 0xff; + ret = (u16)ath5k_hw_bitswap(((srev & 0xf0) >> 4) | + ((srev & 0x0f) << 4), 8); + } + + /* Reset to the 5GHz mode */ + ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0)); + + return ret; +} + +void /*TODO:Boundary check*/ +ath5k_hw_set_def_antenna(struct ath5k_hw *ah, unsigned int ant) +{ + if (ah->ah_version != AR5K_AR5210) + ath5k_hw_reg_write(ah, ant, AR5K_DEFAULT_ANTENNA); +} + +unsigned int ath5k_hw_get_def_antenna(struct ath5k_hw *ah) +{ + if (ah->ah_version != AR5K_AR5210) + return ath5k_hw_reg_read(ah, AR5K_DEFAULT_ANTENNA); + + return 0; /*XXX: What do we return for 5210 ?*/ +} + + +/****************\ +* TX power setup * +\****************/ + +/* + * Helper functions + */ + +/* + * Do linear interpolation between two given (x, y) points + */ +static s16 +ath5k_get_interpolated_value(s16 target, s16 x_left, s16 x_right, + s16 y_left, s16 y_right) +{ + s16 ratio, result; + + /* Avoid divide by zero and skip interpolation + * if we have the same point */ + if ((x_left == x_right) || (y_left == y_right)) + return y_left; + + /* + * Since we use ints and not fps, we need to scale up in + * order to get a sane ratio value (or else we 'll eg. get + * always 1 instead of 1.25, 1.75 etc). We scale up by 100 + * to have some accuracy both for 0.5 and 0.25 steps. + */ + ratio = ((100 * y_right - 100 * y_left)/(x_right - x_left)); + + /* Now scale down to be in range */ + result = y_left + (ratio * (target - x_left) / 100); + + return result; +} + +/* + * Find vertical boundary (min pwr) for the linear PCDAC curve. + * + * Since we have the top of the curve and we draw the line below + * until we reach 1 (1 pcdac step) we need to know which point + * (x value) that is so that we don't go below y axis and have negative + * pcdac values when creating the curve, or fill the table with zeroes. + */ +static s16 +ath5k_get_linear_pcdac_min(const u8 *stepL, const u8 *stepR, + const s16 *pwrL, const s16 *pwrR) +{ + s8 tmp; + s16 min_pwrL, min_pwrR; + s16 pwr_i; + + if (pwrL[0] == pwrL[1]) + min_pwrL = pwrL[0]; + else { + pwr_i = pwrL[0]; + do { + pwr_i--; + tmp = (s8) ath5k_get_interpolated_value(pwr_i, + pwrL[0], pwrL[1], + stepL[0], stepL[1]); + } while (tmp > 1); + + min_pwrL = pwr_i; + } + + if (pwrR[0] == pwrR[1]) + min_pwrR = pwrR[0]; + else { + pwr_i = pwrR[0]; + do { + pwr_i--; + tmp = (s8) ath5k_get_interpolated_value(pwr_i, + pwrR[0], pwrR[1], + stepR[0], stepR[1]); + } while (tmp > 1); + + min_pwrR = pwr_i; + } + + /* Keep the right boundary so that it works for both curves */ + return max(min_pwrL, min_pwrR); +} + +/* + * Interpolate (pwr,vpd) points to create a Power to PDADC or a + * Power to PCDAC curve. + * + * Each curve has power on x axis (in 0.5dB units) and PCDAC/PDADC + * steps (offsets) on y axis. Power can go up to 31.5dB and max + * PCDAC/PDADC step for each curve is 64 but we can write more than + * one curves on hw so we can go up to 128 (which is the max step we + * can write on the final table). + * + * We write y values (PCDAC/PDADC steps) on hw. + */ +static void +ath5k_create_power_curve(s16 pmin, s16 pmax, + const s16 *pwr, const u8 *vpd, + u8 num_points, + u8 *vpd_table, u8 type) +{ + u8 idx[2] = { 0, 1 }; + s16 pwr_i = 2*pmin; + int i; + + if (num_points < 2) + return; + + /* We want the whole line, so adjust boundaries + * to cover the entire power range. Note that + * power values are already 0.25dB so no need + * to multiply pwr_i by 2 */ + if (type == AR5K_PWRTABLE_LINEAR_PCDAC) { + pwr_i = pmin; + pmin = 0; + pmax = 63; + } + + /* Find surrounding turning points (TPs) + * and interpolate between them */ + for (i = 0; (i <= (u16) (pmax - pmin)) && + (i < AR5K_EEPROM_POWER_TABLE_SIZE); i++) { + + /* We passed the right TP, move to the next set of TPs + * if we pass the last TP, extrapolate above using the last + * two TPs for ratio */ + if ((pwr_i > pwr[idx[1]]) && (idx[1] < num_points - 1)) { + idx[0]++; + idx[1]++; + } + + vpd_table[i] = (u8) ath5k_get_interpolated_value(pwr_i, + pwr[idx[0]], pwr[idx[1]], + vpd[idx[0]], vpd[idx[1]]); + + /* Increase by 0.5dB + * (0.25 dB units) */ + pwr_i += 2; + } +} + +/* + * Get the surrounding per-channel power calibration piers + * for a given frequency so that we can interpolate between + * them and come up with an apropriate dataset for our current + * channel. + */ +static void +ath5k_get_chan_pcal_surrounding_piers(struct ath5k_hw *ah, + struct net80211_channel *channel, + struct ath5k_chan_pcal_info **pcinfo_l, + struct ath5k_chan_pcal_info **pcinfo_r) +{ + struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; + struct ath5k_chan_pcal_info *pcinfo; + u8 idx_l, idx_r; + u8 mode, max, i; + u32 target = channel->center_freq; + + idx_l = 0; + idx_r = 0; + + if (!(channel->hw_value & CHANNEL_OFDM)) { + pcinfo = ee->ee_pwr_cal_b; + mode = AR5K_EEPROM_MODE_11B; + } else if (channel->hw_value & CHANNEL_2GHZ) { + pcinfo = ee->ee_pwr_cal_g; + mode = AR5K_EEPROM_MODE_11G; + } else { + pcinfo = ee->ee_pwr_cal_a; + mode = AR5K_EEPROM_MODE_11A; + } + max = ee->ee_n_piers[mode] - 1; + + /* Frequency is below our calibrated + * range. Use the lowest power curve + * we have */ + if (target < pcinfo[0].freq) { + idx_l = idx_r = 0; + goto done; + } + + /* Frequency is above our calibrated + * range. Use the highest power curve + * we have */ + if (target > pcinfo[max].freq) { + idx_l = idx_r = max; + goto done; + } + + /* Frequency is inside our calibrated + * channel range. Pick the surrounding + * calibration piers so that we can + * interpolate */ + for (i = 0; i <= max; i++) { + + /* Frequency matches one of our calibration + * piers, no need to interpolate, just use + * that calibration pier */ + if (pcinfo[i].freq == target) { + idx_l = idx_r = i; + goto done; + } + + /* We found a calibration pier that's above + * frequency, use this pier and the previous + * one to interpolate */ + if (target < pcinfo[i].freq) { + idx_r = i; + idx_l = idx_r - 1; + goto done; + } + } + +done: + *pcinfo_l = &pcinfo[idx_l]; + *pcinfo_r = &pcinfo[idx_r]; + + return; +} + +/* + * Get the surrounding per-rate power calibration data + * for a given frequency and interpolate between power + * values to set max target power supported by hw for + * each rate. + */ +static void +ath5k_get_rate_pcal_data(struct ath5k_hw *ah, + struct net80211_channel *channel, + struct ath5k_rate_pcal_info *rates) +{ + struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; + struct ath5k_rate_pcal_info *rpinfo; + u8 idx_l, idx_r; + u8 mode, max, i; + u32 target = channel->center_freq; + + idx_l = 0; + idx_r = 0; + + if (!(channel->hw_value & CHANNEL_OFDM)) { + rpinfo = ee->ee_rate_tpwr_b; + mode = AR5K_EEPROM_MODE_11B; + } else if (channel->hw_value & CHANNEL_2GHZ) { + rpinfo = ee->ee_rate_tpwr_g; + mode = AR5K_EEPROM_MODE_11G; + } else { + rpinfo = ee->ee_rate_tpwr_a; + mode = AR5K_EEPROM_MODE_11A; + } + max = ee->ee_rate_target_pwr_num[mode] - 1; + + /* Get the surrounding calibration + * piers - same as above */ + if (target < rpinfo[0].freq) { + idx_l = idx_r = 0; + goto done; + } + + if (target > rpinfo[max].freq) { + idx_l = idx_r = max; + goto done; + } + + for (i = 0; i <= max; i++) { + + if (rpinfo[i].freq == target) { + idx_l = idx_r = i; + goto done; + } + + if (target < rpinfo[i].freq) { + idx_r = i; + idx_l = idx_r - 1; + goto done; + } + } + +done: + /* Now interpolate power value, based on the frequency */ + rates->freq = target; + + rates->target_power_6to24 = + ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, + rpinfo[idx_r].freq, + rpinfo[idx_l].target_power_6to24, + rpinfo[idx_r].target_power_6to24); + + rates->target_power_36 = + ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, + rpinfo[idx_r].freq, + rpinfo[idx_l].target_power_36, + rpinfo[idx_r].target_power_36); + + rates->target_power_48 = + ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, + rpinfo[idx_r].freq, + rpinfo[idx_l].target_power_48, + rpinfo[idx_r].target_power_48); + + rates->target_power_54 = + ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, + rpinfo[idx_r].freq, + rpinfo[idx_l].target_power_54, + rpinfo[idx_r].target_power_54); +} + +/* + * Get the max edge power for this channel if + * we have such data from EEPROM's Conformance Test + * Limits (CTL), and limit max power if needed. + * + * FIXME: Only works for world regulatory domains + */ +static void +ath5k_get_max_ctl_power(struct ath5k_hw *ah, + struct net80211_channel *channel) +{ + struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; + struct ath5k_edge_power *rep = ee->ee_ctl_pwr; + u8 *ctl_val = ee->ee_ctl; + s16 max_chan_pwr = ah->ah_txpower.txp_max_pwr / 4; + s16 edge_pwr = 0; + u8 rep_idx; + u8 i, ctl_mode; + u8 ctl_idx = 0xFF; + u32 target = channel->center_freq; + + /* Find out a CTL for our mode that's not mapped + * on a specific reg domain. + * + * TODO: Map our current reg domain to one of the 3 available + * reg domain ids so that we can support more CTLs. */ + switch (channel->hw_value & CHANNEL_MODES) { + case CHANNEL_A: + ctl_mode = AR5K_CTL_11A | AR5K_CTL_NO_REGDOMAIN; + break; + case CHANNEL_G: + ctl_mode = AR5K_CTL_11G | AR5K_CTL_NO_REGDOMAIN; + break; + case CHANNEL_B: + ctl_mode = AR5K_CTL_11B | AR5K_CTL_NO_REGDOMAIN; + break; + case CHANNEL_T: + ctl_mode = AR5K_CTL_TURBO | AR5K_CTL_NO_REGDOMAIN; + break; + case CHANNEL_TG: + ctl_mode = AR5K_CTL_TURBOG | AR5K_CTL_NO_REGDOMAIN; + break; + case CHANNEL_XR: + /* Fall through */ + default: + return; + } + + for (i = 0; i < ee->ee_ctls; i++) { + if (ctl_val[i] == ctl_mode) { + ctl_idx = i; + break; + } + } + + /* If we have a CTL dataset available grab it and find the + * edge power for our frequency */ + if (ctl_idx == 0xFF) + return; + + /* Edge powers are sorted by frequency from lower + * to higher. Each CTL corresponds to 8 edge power + * measurements. */ + rep_idx = ctl_idx * AR5K_EEPROM_N_EDGES; + + /* Don't do boundaries check because we + * might have more that one bands defined + * for this mode */ + + /* Get the edge power that's closer to our + * frequency */ + for (i = 0; i < AR5K_EEPROM_N_EDGES; i++) { + rep_idx += i; + if (target <= rep[rep_idx].freq) + edge_pwr = (s16) rep[rep_idx].edge; + } + + if (edge_pwr) { + ah->ah_txpower.txp_max_pwr = 4*min(edge_pwr, max_chan_pwr); + } +} + + +/* + * Power to PCDAC table functions + */ + +/* + * Fill Power to PCDAC table on RF5111 + * + * No further processing is needed for RF5111, the only thing we have to + * do is fill the values below and above calibration range since eeprom data + * may not cover the entire PCDAC table. + */ +static void +ath5k_fill_pwr_to_pcdac_table(struct ath5k_hw *ah, s16* table_min, + s16 *table_max) +{ + u8 *pcdac_out = ah->ah_txpower.txp_pd_table; + u8 *pcdac_tmp = ah->ah_txpower.tmpL[0]; + u8 pcdac_0, pcdac_n, pcdac_i, pwr_idx, i; + s16 min_pwr, max_pwr; + + /* Get table boundaries */ + min_pwr = table_min[0]; + pcdac_0 = pcdac_tmp[0]; + + max_pwr = table_max[0]; + pcdac_n = pcdac_tmp[table_max[0] - table_min[0]]; + + /* Extrapolate below minimum using pcdac_0 */ + pcdac_i = 0; + for (i = 0; i < min_pwr; i++) + pcdac_out[pcdac_i++] = pcdac_0; + + /* Copy values from pcdac_tmp */ + pwr_idx = min_pwr; + for (i = 0 ; pwr_idx <= max_pwr && + pcdac_i < AR5K_EEPROM_POWER_TABLE_SIZE; i++) { + pcdac_out[pcdac_i++] = pcdac_tmp[i]; + pwr_idx++; + } + + /* Extrapolate above maximum */ + while (pcdac_i < AR5K_EEPROM_POWER_TABLE_SIZE) + pcdac_out[pcdac_i++] = pcdac_n; + +} + +/* + * Combine available XPD Curves and fill Linear Power to PCDAC table + * on RF5112 + * + * RFX112 can have up to 2 curves (one for low txpower range and one for + * higher txpower range). We need to put them both on pcdac_out and place + * them in the correct location. In case we only have one curve available + * just fit it on pcdac_out (it's supposed to cover the entire range of + * available pwr levels since it's always the higher power curve). Extrapolate + * below and above final table if needed. + */ +static void +ath5k_combine_linear_pcdac_curves(struct ath5k_hw *ah, s16* table_min, + s16 *table_max, u8 pdcurves) +{ + u8 *pcdac_out = ah->ah_txpower.txp_pd_table; + u8 *pcdac_low_pwr; + u8 *pcdac_high_pwr; + u8 *pcdac_tmp; + u8 pwr; + s16 max_pwr_idx; + s16 min_pwr_idx; + s16 mid_pwr_idx = 0; + /* Edge flag turs on the 7nth bit on the PCDAC + * to delcare the higher power curve (force values + * to be greater than 64). If we only have one curve + * we don't need to set this, if we have 2 curves and + * fill the table backwards this can also be used to + * switch from higher power curve to lower power curve */ + u8 edge_flag; + int i; + + /* When we have only one curve available + * that's the higher power curve. If we have + * two curves the first is the high power curve + * and the next is the low power curve. */ + if (pdcurves > 1) { + pcdac_low_pwr = ah->ah_txpower.tmpL[1]; + pcdac_high_pwr = ah->ah_txpower.tmpL[0]; + mid_pwr_idx = table_max[1] - table_min[1] - 1; + max_pwr_idx = (table_max[0] - table_min[0]) / 2; + + /* If table size goes beyond 31.5dB, keep the + * upper 31.5dB range when setting tx power. + * Note: 126 = 31.5 dB in quarter dB steps */ + if (table_max[0] - table_min[1] > 126) + min_pwr_idx = table_max[0] - 126; + else + min_pwr_idx = table_min[1]; + + /* Since we fill table backwards + * start from high power curve */ + pcdac_tmp = pcdac_high_pwr; + + edge_flag = 0x40; + } else { + pcdac_low_pwr = ah->ah_txpower.tmpL[1]; /* Zeroed */ + pcdac_high_pwr = ah->ah_txpower.tmpL[0]; + min_pwr_idx = table_min[0]; + max_pwr_idx = (table_max[0] - table_min[0]) / 2; + pcdac_tmp = pcdac_high_pwr; + edge_flag = 0; + } + + /* This is used when setting tx power*/ + ah->ah_txpower.txp_min_idx = min_pwr_idx/2; + + /* Fill Power to PCDAC table backwards */ + pwr = max_pwr_idx; + for (i = 63; i >= 0; i--) { + /* Entering lower power range, reset + * edge flag and set pcdac_tmp to lower + * power curve.*/ + if (edge_flag == 0x40 && + (2*pwr <= (table_max[1] - table_min[0]) || pwr == 0)) { + edge_flag = 0x00; + pcdac_tmp = pcdac_low_pwr; + pwr = mid_pwr_idx/2; + } + + /* Don't go below 1, extrapolate below if we have + * already swithced to the lower power curve -or + * we only have one curve and edge_flag is zero + * anyway */ + if (pcdac_tmp[pwr] < 1 && (edge_flag == 0x00)) { + while (i >= 0) { + pcdac_out[i] = pcdac_out[i + 1]; + i--; + } + break; + } + + pcdac_out[i] = pcdac_tmp[pwr] | edge_flag; + + /* Extrapolate above if pcdac is greater than + * 126 -this can happen because we OR pcdac_out + * value with edge_flag on high power curve */ + if (pcdac_out[i] > 126) + pcdac_out[i] = 126; + + /* Decrease by a 0.5dB step */ + pwr--; + } +} + +/* Write PCDAC values on hw */ +static void +ath5k_setup_pcdac_table(struct ath5k_hw *ah) +{ + u8 *pcdac_out = ah->ah_txpower.txp_pd_table; + int i; + + /* + * Write TX power values + */ + for (i = 0; i < (AR5K_EEPROM_POWER_TABLE_SIZE / 2); i++) { + ath5k_hw_reg_write(ah, + (((pcdac_out[2*i + 0] << 8 | 0xff) & 0xffff) << 0) | + (((pcdac_out[2*i + 1] << 8 | 0xff) & 0xffff) << 16), + AR5K_PHY_PCDAC_TXPOWER(i)); + } +} + + +/* + * Power to PDADC table functions + */ + +/* + * Set the gain boundaries and create final Power to PDADC table + * + * We can have up to 4 pd curves, we need to do a simmilar process + * as we do for RF5112. This time we don't have an edge_flag but we + * set the gain boundaries on a separate register. + */ +static void +ath5k_combine_pwr_to_pdadc_curves(struct ath5k_hw *ah, + s16 *pwr_min, s16 *pwr_max, u8 pdcurves) +{ + u8 gain_boundaries[AR5K_EEPROM_N_PD_GAINS]; + u8 *pdadc_out = ah->ah_txpower.txp_pd_table; + u8 *pdadc_tmp; + s16 pdadc_0; + u8 pdadc_i, pdadc_n, pwr_step, pdg, max_idx, table_size; + u8 pd_gain_overlap; + + /* Note: Register value is initialized on initvals + * there is no feedback from hw. + * XXX: What about pd_gain_overlap from EEPROM ? */ + pd_gain_overlap = (u8) ath5k_hw_reg_read(ah, AR5K_PHY_TPC_RG5) & + AR5K_PHY_TPC_RG5_PD_GAIN_OVERLAP; + + /* Create final PDADC table */ + for (pdg = 0, pdadc_i = 0; pdg < pdcurves; pdg++) { + pdadc_tmp = ah->ah_txpower.tmpL[pdg]; + + if (pdg == pdcurves - 1) + /* 2 dB boundary stretch for last + * (higher power) curve */ + gain_boundaries[pdg] = pwr_max[pdg] + 4; + else + /* Set gain boundary in the middle + * between this curve and the next one */ + gain_boundaries[pdg] = + (pwr_max[pdg] + pwr_min[pdg + 1]) / 2; + + /* Sanity check in case our 2 db stretch got out of + * range. */ + if (gain_boundaries[pdg] > AR5K_TUNE_MAX_TXPOWER) + gain_boundaries[pdg] = AR5K_TUNE_MAX_TXPOWER; + + /* For the first curve (lower power) + * start from 0 dB */ + if (pdg == 0) + pdadc_0 = 0; + else + /* For the other curves use the gain overlap */ + pdadc_0 = (gain_boundaries[pdg - 1] - pwr_min[pdg]) - + pd_gain_overlap; + + /* Force each power step to be at least 0.5 dB */ + if ((pdadc_tmp[1] - pdadc_tmp[0]) > 1) + pwr_step = pdadc_tmp[1] - pdadc_tmp[0]; + else + pwr_step = 1; + + /* If pdadc_0 is negative, we need to extrapolate + * below this pdgain by a number of pwr_steps */ + while ((pdadc_0 < 0) && (pdadc_i < 128)) { + s16 tmp = pdadc_tmp[0] + pdadc_0 * pwr_step; + pdadc_out[pdadc_i++] = (tmp < 0) ? 0 : (u8) tmp; + pdadc_0++; + } + + /* Set last pwr level, using gain boundaries */ + pdadc_n = gain_boundaries[pdg] + pd_gain_overlap - pwr_min[pdg]; + /* Limit it to be inside pwr range */ + table_size = pwr_max[pdg] - pwr_min[pdg]; + max_idx = (pdadc_n < table_size) ? pdadc_n : table_size; + + /* Fill pdadc_out table */ + while (pdadc_0 < max_idx) + pdadc_out[pdadc_i++] = pdadc_tmp[pdadc_0++]; + + /* Need to extrapolate above this pdgain? */ + if (pdadc_n <= max_idx) + continue; + + /* Force each power step to be at least 0.5 dB */ + if ((pdadc_tmp[table_size - 1] - pdadc_tmp[table_size - 2]) > 1) + pwr_step = pdadc_tmp[table_size - 1] - + pdadc_tmp[table_size - 2]; + else + pwr_step = 1; + + /* Extrapolate above */ + while ((pdadc_0 < (s16) pdadc_n) && + (pdadc_i < AR5K_EEPROM_POWER_TABLE_SIZE * 2)) { + s16 tmp = pdadc_tmp[table_size - 1] + + (pdadc_0 - max_idx) * pwr_step; + pdadc_out[pdadc_i++] = (tmp > 127) ? 127 : (u8) tmp; + pdadc_0++; + } + } + + while (pdg < AR5K_EEPROM_N_PD_GAINS) { + gain_boundaries[pdg] = gain_boundaries[pdg - 1]; + pdg++; + } + + while (pdadc_i < AR5K_EEPROM_POWER_TABLE_SIZE * 2) { + pdadc_out[pdadc_i] = pdadc_out[pdadc_i - 1]; + pdadc_i++; + } + + /* Set gain boundaries */ + ath5k_hw_reg_write(ah, + AR5K_REG_SM(pd_gain_overlap, + AR5K_PHY_TPC_RG5_PD_GAIN_OVERLAP) | + AR5K_REG_SM(gain_boundaries[0], + AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_1) | + AR5K_REG_SM(gain_boundaries[1], + AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_2) | + AR5K_REG_SM(gain_boundaries[2], + AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_3) | + AR5K_REG_SM(gain_boundaries[3], + AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_4), + AR5K_PHY_TPC_RG5); + + /* Used for setting rate power table */ + ah->ah_txpower.txp_min_idx = pwr_min[0]; + +} + +/* Write PDADC values on hw */ +static void +ath5k_setup_pwr_to_pdadc_table(struct ath5k_hw *ah, + u8 pdcurves, u8 *pdg_to_idx) +{ + u8 *pdadc_out = ah->ah_txpower.txp_pd_table; + u32 reg; + u8 i; + + /* Select the right pdgain curves */ + + /* Clear current settings */ + reg = ath5k_hw_reg_read(ah, AR5K_PHY_TPC_RG1); + reg &= ~(AR5K_PHY_TPC_RG1_PDGAIN_1 | + AR5K_PHY_TPC_RG1_PDGAIN_2 | + AR5K_PHY_TPC_RG1_PDGAIN_3 | + AR5K_PHY_TPC_RG1_NUM_PD_GAIN); + + /* + * Use pd_gains curve from eeprom + * + * This overrides the default setting from initvals + * in case some vendors (e.g. Zcomax) don't use the default + * curves. If we don't honor their settings we 'll get a + * 5dB (1 * gain overlap ?) drop. + */ + reg |= AR5K_REG_SM(pdcurves, AR5K_PHY_TPC_RG1_NUM_PD_GAIN); + + switch (pdcurves) { + case 3: + reg |= AR5K_REG_SM(pdg_to_idx[2], AR5K_PHY_TPC_RG1_PDGAIN_3); + /* Fall through */ + case 2: + reg |= AR5K_REG_SM(pdg_to_idx[1], AR5K_PHY_TPC_RG1_PDGAIN_2); + /* Fall through */ + case 1: + reg |= AR5K_REG_SM(pdg_to_idx[0], AR5K_PHY_TPC_RG1_PDGAIN_1); + break; + } + ath5k_hw_reg_write(ah, reg, AR5K_PHY_TPC_RG1); + + /* + * Write TX power values + */ + for (i = 0; i < (AR5K_EEPROM_POWER_TABLE_SIZE / 2); i++) { + ath5k_hw_reg_write(ah, + ((pdadc_out[4*i + 0] & 0xff) << 0) | + ((pdadc_out[4*i + 1] & 0xff) << 8) | + ((pdadc_out[4*i + 2] & 0xff) << 16) | + ((pdadc_out[4*i + 3] & 0xff) << 24), + AR5K_PHY_PDADC_TXPOWER(i)); + } +} + + +/* + * Common code for PCDAC/PDADC tables + */ + +/* + * This is the main function that uses all of the above + * to set PCDAC/PDADC table on hw for the current channel. + * This table is used for tx power calibration on the basband, + * without it we get weird tx power levels and in some cases + * distorted spectral mask + */ +static int +ath5k_setup_channel_powertable(struct ath5k_hw *ah, + struct net80211_channel *channel, + u8 ee_mode, u8 type) +{ + struct ath5k_pdgain_info *pdg_L, *pdg_R; + struct ath5k_chan_pcal_info *pcinfo_L; + struct ath5k_chan_pcal_info *pcinfo_R; + struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; + u8 *pdg_curve_to_idx = ee->ee_pdc_to_idx[ee_mode]; + s16 table_min[AR5K_EEPROM_N_PD_GAINS]; + s16 table_max[AR5K_EEPROM_N_PD_GAINS]; + u8 *tmpL; + u8 *tmpR; + u32 target = channel->center_freq; + int pdg, i; + + /* Get surounding freq piers for this channel */ + ath5k_get_chan_pcal_surrounding_piers(ah, channel, + &pcinfo_L, + &pcinfo_R); + + /* Loop over pd gain curves on + * surounding freq piers by index */ + for (pdg = 0; pdg < ee->ee_pd_gains[ee_mode]; pdg++) { + + /* Fill curves in reverse order + * from lower power (max gain) + * to higher power. Use curve -> idx + * backmaping we did on eeprom init */ + u8 idx = pdg_curve_to_idx[pdg]; + + /* Grab the needed curves by index */ + pdg_L = &pcinfo_L->pd_curves[idx]; + pdg_R = &pcinfo_R->pd_curves[idx]; + + /* Initialize the temp tables */ + tmpL = ah->ah_txpower.tmpL[pdg]; + tmpR = ah->ah_txpower.tmpR[pdg]; + + /* Set curve's x boundaries and create + * curves so that they cover the same + * range (if we don't do that one table + * will have values on some range and the + * other one won't have any so interpolation + * will fail) */ + table_min[pdg] = min(pdg_L->pd_pwr[0], + pdg_R->pd_pwr[0]) / 2; + + table_max[pdg] = max(pdg_L->pd_pwr[pdg_L->pd_points - 1], + pdg_R->pd_pwr[pdg_R->pd_points - 1]) / 2; + + /* Now create the curves on surrounding channels + * and interpolate if needed to get the final + * curve for this gain on this channel */ + switch (type) { + case AR5K_PWRTABLE_LINEAR_PCDAC: + /* Override min/max so that we don't loose + * accuracy (don't divide by 2) */ + table_min[pdg] = min(pdg_L->pd_pwr[0], + pdg_R->pd_pwr[0]); + + table_max[pdg] = + max(pdg_L->pd_pwr[pdg_L->pd_points - 1], + pdg_R->pd_pwr[pdg_R->pd_points - 1]); + + /* Override minimum so that we don't get + * out of bounds while extrapolating + * below. Don't do this when we have 2 + * curves and we are on the high power curve + * because table_min is ok in this case */ + if (!(ee->ee_pd_gains[ee_mode] > 1 && pdg == 0)) { + + table_min[pdg] = + ath5k_get_linear_pcdac_min(pdg_L->pd_step, + pdg_R->pd_step, + pdg_L->pd_pwr, + pdg_R->pd_pwr); + + /* Don't go too low because we will + * miss the upper part of the curve. + * Note: 126 = 31.5dB (max power supported) + * in 0.25dB units */ + if (table_max[pdg] - table_min[pdg] > 126) + table_min[pdg] = table_max[pdg] - 126; + } + + /* Fall through */ + case AR5K_PWRTABLE_PWR_TO_PCDAC: + case AR5K_PWRTABLE_PWR_TO_PDADC: + + ath5k_create_power_curve(table_min[pdg], + table_max[pdg], + pdg_L->pd_pwr, + pdg_L->pd_step, + pdg_L->pd_points, tmpL, type); + + /* We are in a calibration + * pier, no need to interpolate + * between freq piers */ + if (pcinfo_L == pcinfo_R) + continue; + + ath5k_create_power_curve(table_min[pdg], + table_max[pdg], + pdg_R->pd_pwr, + pdg_R->pd_step, + pdg_R->pd_points, tmpR, type); + break; + default: + return -EINVAL; + } + + /* Interpolate between curves + * of surounding freq piers to + * get the final curve for this + * pd gain. Re-use tmpL for interpolation + * output */ + for (i = 0; (i < (u16) (table_max[pdg] - table_min[pdg])) && + (i < AR5K_EEPROM_POWER_TABLE_SIZE); i++) { + tmpL[i] = (u8) ath5k_get_interpolated_value(target, + (s16) pcinfo_L->freq, + (s16) pcinfo_R->freq, + (s16) tmpL[i], + (s16) tmpR[i]); + } + } + + /* Now we have a set of curves for this + * channel on tmpL (x range is table_max - table_min + * and y values are tmpL[pdg][]) sorted in the same + * order as EEPROM (because we've used the backmaping). + * So for RF5112 it's from higher power to lower power + * and for RF2413 it's from lower power to higher power. + * For RF5111 we only have one curve. */ + + /* Fill min and max power levels for this + * channel by interpolating the values on + * surounding channels to complete the dataset */ + ah->ah_txpower.txp_min_pwr = ath5k_get_interpolated_value(target, + (s16) pcinfo_L->freq, + (s16) pcinfo_R->freq, + pcinfo_L->min_pwr, pcinfo_R->min_pwr); + + ah->ah_txpower.txp_max_pwr = ath5k_get_interpolated_value(target, + (s16) pcinfo_L->freq, + (s16) pcinfo_R->freq, + pcinfo_L->max_pwr, pcinfo_R->max_pwr); + + /* We are ready to go, fill PCDAC/PDADC + * table and write settings on hardware */ + switch (type) { + case AR5K_PWRTABLE_LINEAR_PCDAC: + /* For RF5112 we can have one or two curves + * and each curve covers a certain power lvl + * range so we need to do some more processing */ + ath5k_combine_linear_pcdac_curves(ah, table_min, table_max, + ee->ee_pd_gains[ee_mode]); + + /* Set txp.offset so that we can + * match max power value with max + * table index */ + ah->ah_txpower.txp_offset = 64 - (table_max[0] / 2); + + /* Write settings on hw */ + ath5k_setup_pcdac_table(ah); + break; + case AR5K_PWRTABLE_PWR_TO_PCDAC: + /* We are done for RF5111 since it has only + * one curve, just fit the curve on the table */ + ath5k_fill_pwr_to_pcdac_table(ah, table_min, table_max); + + /* No rate powertable adjustment for RF5111 */ + ah->ah_txpower.txp_min_idx = 0; + ah->ah_txpower.txp_offset = 0; + + /* Write settings on hw */ + ath5k_setup_pcdac_table(ah); + break; + case AR5K_PWRTABLE_PWR_TO_PDADC: + /* Set PDADC boundaries and fill + * final PDADC table */ + ath5k_combine_pwr_to_pdadc_curves(ah, table_min, table_max, + ee->ee_pd_gains[ee_mode]); + + /* Write settings on hw */ + ath5k_setup_pwr_to_pdadc_table(ah, pdg, pdg_curve_to_idx); + + /* Set txp.offset, note that table_min + * can be negative */ + ah->ah_txpower.txp_offset = table_min[0]; + break; + default: + return -EINVAL; + } + + return 0; +} + + +/* + * Per-rate tx power setting + * + * This is the code that sets the desired tx power (below + * maximum) on hw for each rate (we also have TPC that sets + * power per packet). We do that by providing an index on the + * PCDAC/PDADC table we set up. + */ + +/* + * Set rate power table + * + * For now we only limit txpower based on maximum tx power + * supported by hw (what's inside rate_info). We need to limit + * this even more, based on regulatory domain etc. + * + * Rate power table contains indices to PCDAC/PDADC table (0.5dB steps) + * and is indexed as follows: + * rates[0] - rates[7] -> OFDM rates + * rates[8] - rates[14] -> CCK rates + * rates[15] -> XR rates (they all have the same power) + */ +static void +ath5k_setup_rate_powertable(struct ath5k_hw *ah, u16 max_pwr, + struct ath5k_rate_pcal_info *rate_info, + u8 ee_mode) +{ + unsigned int i; + u16 *rates; + + /* max_pwr is power level we got from driver/user in 0.5dB + * units, switch to 0.25dB units so we can compare */ + max_pwr *= 2; + max_pwr = min(max_pwr, (u16) ah->ah_txpower.txp_max_pwr) / 2; + + /* apply rate limits */ + rates = ah->ah_txpower.txp_rates_power_table; + + /* OFDM rates 6 to 24Mb/s */ + for (i = 0; i < 5; i++) + rates[i] = min(max_pwr, rate_info->target_power_6to24); + + /* Rest OFDM rates */ + rates[5] = min(rates[0], rate_info->target_power_36); + rates[6] = min(rates[0], rate_info->target_power_48); + rates[7] = min(rates[0], rate_info->target_power_54); + + /* CCK rates */ + /* 1L */ + rates[8] = min(rates[0], rate_info->target_power_6to24); + /* 2L */ + rates[9] = min(rates[0], rate_info->target_power_36); + /* 2S */ + rates[10] = min(rates[0], rate_info->target_power_36); + /* 5L */ + rates[11] = min(rates[0], rate_info->target_power_48); + /* 5S */ + rates[12] = min(rates[0], rate_info->target_power_48); + /* 11L */ + rates[13] = min(rates[0], rate_info->target_power_54); + /* 11S */ + rates[14] = min(rates[0], rate_info->target_power_54); + + /* XR rates */ + rates[15] = min(rates[0], rate_info->target_power_6to24); + + /* CCK rates have different peak to average ratio + * so we have to tweak their power so that gainf + * correction works ok. For this we use OFDM to + * CCK delta from eeprom */ + if ((ee_mode == AR5K_EEPROM_MODE_11G) && + (ah->ah_phy_revision < AR5K_SREV_PHY_5212A)) + for (i = 8; i <= 15; i++) + rates[i] -= ah->ah_txpower.txp_cck_ofdm_gainf_delta; + + ah->ah_txpower.txp_min_pwr = rates[7]; + ah->ah_txpower.txp_max_pwr = rates[0]; + ah->ah_txpower.txp_ofdm = rates[7]; +} + + +/* + * Set transmition power + */ +int +ath5k_hw_txpower(struct ath5k_hw *ah, struct net80211_channel *channel, + u8 ee_mode, u8 txpower) +{ + struct ath5k_rate_pcal_info rate_info; + u8 type; + int ret; + + if (txpower > AR5K_TUNE_MAX_TXPOWER) { + DBG("ath5k: invalid tx power %d\n", txpower); + return -EINVAL; + } + if (txpower == 0) + txpower = AR5K_TUNE_DEFAULT_TXPOWER; + + /* Reset TX power values */ + memset(&ah->ah_txpower, 0, sizeof(ah->ah_txpower)); + ah->ah_txpower.txp_tpc = AR5K_TUNE_TPC_TXPOWER; + ah->ah_txpower.txp_min_pwr = 0; + ah->ah_txpower.txp_max_pwr = AR5K_TUNE_MAX_TXPOWER; + + /* Initialize TX power table */ + switch (ah->ah_radio) { + case AR5K_RF5111: + type = AR5K_PWRTABLE_PWR_TO_PCDAC; + break; + case AR5K_RF5112: + type = AR5K_PWRTABLE_LINEAR_PCDAC; + break; + case AR5K_RF2413: + case AR5K_RF5413: + case AR5K_RF2316: + case AR5K_RF2317: + case AR5K_RF2425: + type = AR5K_PWRTABLE_PWR_TO_PDADC; + break; + default: + return -EINVAL; + } + + /* FIXME: Only on channel/mode change */ + ret = ath5k_setup_channel_powertable(ah, channel, ee_mode, type); + if (ret) + return ret; + + /* Limit max power if we have a CTL available */ + ath5k_get_max_ctl_power(ah, channel); + + /* FIXME: Tx power limit for this regdomain + * XXX: Mac80211/CRDA will do that anyway ? */ + + /* FIXME: Antenna reduction stuff */ + + /* FIXME: Limit power on turbo modes */ + + /* FIXME: TPC scale reduction */ + + /* Get surounding channels for per-rate power table + * calibration */ + ath5k_get_rate_pcal_data(ah, channel, &rate_info); + + /* Setup rate power table */ + ath5k_setup_rate_powertable(ah, txpower, &rate_info, ee_mode); + + /* Write rate power table on hw */ + ath5k_hw_reg_write(ah, AR5K_TXPOWER_OFDM(3, 24) | + AR5K_TXPOWER_OFDM(2, 16) | AR5K_TXPOWER_OFDM(1, 8) | + AR5K_TXPOWER_OFDM(0, 0), AR5K_PHY_TXPOWER_RATE1); + + ath5k_hw_reg_write(ah, AR5K_TXPOWER_OFDM(7, 24) | + AR5K_TXPOWER_OFDM(6, 16) | AR5K_TXPOWER_OFDM(5, 8) | + AR5K_TXPOWER_OFDM(4, 0), AR5K_PHY_TXPOWER_RATE2); + + ath5k_hw_reg_write(ah, AR5K_TXPOWER_CCK(10, 24) | + AR5K_TXPOWER_CCK(9, 16) | AR5K_TXPOWER_CCK(15, 8) | + AR5K_TXPOWER_CCK(8, 0), AR5K_PHY_TXPOWER_RATE3); + + ath5k_hw_reg_write(ah, AR5K_TXPOWER_CCK(14, 24) | + AR5K_TXPOWER_CCK(13, 16) | AR5K_TXPOWER_CCK(12, 8) | + AR5K_TXPOWER_CCK(11, 0), AR5K_PHY_TXPOWER_RATE4); + + /* FIXME: TPC support */ + if (ah->ah_txpower.txp_tpc) { + ath5k_hw_reg_write(ah, AR5K_PHY_TXPOWER_RATE_MAX_TPC_ENABLE | + AR5K_TUNE_MAX_TXPOWER, AR5K_PHY_TXPOWER_RATE_MAX); + + ath5k_hw_reg_write(ah, + AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_ACK) | + AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_CTS) | + AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_CHIRP), + AR5K_TPC); + } else { + ath5k_hw_reg_write(ah, AR5K_PHY_TXPOWER_RATE_MAX | + AR5K_TUNE_MAX_TXPOWER, AR5K_PHY_TXPOWER_RATE_MAX); + } + + return 0; +} + +int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 mode, u8 txpower) +{ + struct net80211_channel *channel = ah->ah_current_channel; + + DBG2("ath5k: changing txpower to %d\n", txpower); + + return ath5k_hw_txpower(ah, channel, mode, txpower); +} + +#undef _ATH5K_PHY -- cgit v1.2.3